=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2008.03.21 11:21:46 =~=~=~=~=~=~=~=~=~=~=~= RACK98AS>8 [Resuming connection 8 to s1 ... ] S1(config)#hostname S1 S1(config)#! S1(config)#! S1(config)#username CISCO password 0 CISCO S1(config)#ip subnet-zero S1(config)#ip routing S1(config)#no ip domain-lookup S1(config)#! S1(config)#vtp domain CCIE Changing VTP domain name from NULL to CCIE S1(config)#vlan 3 S1(config-vlan)#name R3 S1(config-vlan)#vlan 174 S1(config-vlan)#name R1-7-4 S1(config-vlan)#vlan 52 S1(config-vlan)#name R5-2 S1(config-vlan)#no file verify auto S1(config)#spanning-tree mode pvst S1(config)#spanning-tree extend system-id S1(config)#interface Port-channel1 S1(config-if)# switchport trunk encapsulation dot1q S1(config-if)# switchport mode trunk S1(config-if)#! S1(config-if)#interface FastEthernet0/1 S1(config-if)# switchport access vlan 174 S1(config-if)# switchport mode access S1(config-if)# l2protocol-tunnel cdp S1(config-if)# no cdp enable S1(config-if)#! S1(config-if)#interface FastEthernet0/2 S1(config-if)# switchport access vlan 52 S1(config-if)# switchport mode access S1(config-if)#! S1(config-if)#interface FastEthernet0/3 S1(config-if)# switchport access vlan 3 S1(config-if)# switchport mode access S1(config-if)#! S1(config-if)#interface FastEthernet0/4 S1(config-if)# switchport mode dynamic desirable S1(config-if)#! S1(config-if)#interface FastEthernet0/5 S1(config-if)# switchport mode dynamic desirable S1(config-if)#! S1(config-if)#interface FastEthernet0/6 S1(config-if)# switchport mode dynamic desirable S1(config-if)#! S1(config-if)#interface FastEthernet0/7 S1(config-if)# switchport access vlan 174 S1(config-if)# switchport mode access S1(config-if)# l2protocol-tunnel cdp S1(config-if)# no cdp enable S1(config-if)#! S1(config-if)#interface FastEthernet0/12 S1(config-if)# switchport trunk encapsulation dot1q S1(config-if)# switchport mode trunk S1(config-if)#! S1(config-if)#interface FastEthernet0/13 S1(config-if)# switchport trunk encapsulation dot1q S1(config-if)# switchport mode trunk S1(config-if)#! S1(config-if)#interface FastEthernet0/20 S1(config-if)# switchport mode dynamic desirable S1(config-if)# shutdown S1(config-if)#! S1(config-if)#interface FastEthernet0/22 S1(config-if)# switchport trunk encapsulation dot1q S1(config-if)# switchport mode trunk S1(config-if)# channel-group 1 mode desirable S1(config-if)#! S1(config-if)#interface FastEthernet0/23 S1(config-if)# switchport trunk encapsulation dot1q S1(config-if)# switchport mode trunk S1(config-if)# channel-group 1 mode desirable S1(config-if)#! S1(config-if)#interface FastEthernet0/24 S1(config-if)# switchport trunk encapsulation dot1q S1(config-if)# switchport mode trunk S1(config-if)# channel-group 1 mode desirable S1(config-if)#! S1(config-if)#interface Vlan174 S1(config-if)# ip address 172.22.174.8 255.255.255.192 S1(config-if)# no shutdown S1(config-if)#! S1(config-if)#router eigrp 174 S1(config-router)# network 172.22.0.0 S1(config-router)# no auto-summary S1(config-router)#! S1(config-router)#line con 0 S1(config-line)# exec-timeout 0 0 S1(config-line)# privilege level 15 S1(config-line)# logging synchronous S1(config-line)#line vty 0 4 S1(config-line)# password cisco S1(config-line)# login local S1(config-line)#line vty 5 15 S1(config-line)# password cisco S1(config-line)# login local S1(config-line)#! S1(config-line)#end S1# 02:41:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/12, changed state to down 02:41:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down 02:41:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down 02:41:10: %SYS-5-CONFIG_I: Configured from console by console 02:41:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down 02:41:11: %LINEPROTO-5-UPDOWN: Line protocol on In S1#terface FastEthernet0/24, changed state to down 02:41:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan174, changed state to down S1# 02:41:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/12, changed state to up 02:41:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up S1#wr Building configuration... [OK] S1# RACK98AS>9 [Resuming connection 9 to s2 ... ] 02:41:04: %LINE S2(config)# RACK98AS>5 [Resuming connection 5 to r5 ... ] R5(config)#do sh iunt     nt fa 0/1 FastEthernet0/1 is up, line protocol is up Hardware is Gt96k FE, address is 001a.6d1a.3e81 (bia 001a.6d1a.3e81) Internet address is 172.22.52.5/27 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:03, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 487 packets input, 75872 bytes Received 487 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 1143 packets output, 118197 bytes, 0 underruns 0 output errors, 0 collisions, 3 interface resets --More-- RACK98AS>9 [Resuming connection 9 to s2 ... ] S2(config)#hostname S2 S2(config)#! S2(config)#username CISCO password 0 CISCO S2(config)#ip subnet-zero S2(config)#ip routing S2(config)#no ip domain-lookup S2(config)#! S2(config)#! Need to get R5 mac address from Fa0/1 and update this ACL S2(config)#! S2(config)#no mac access-list extended R5 S2(config)# mac access-list extended R5 S2(config-ext-macl)# permit host 001a.6d1a.3e81 any S2(config-ext-macl)#! S2(config-ext-macl)# vlan access-map R5 10 S2(config-access-map)# action drop S2(config-access-map)# match mac address R5 S2(config-access-map)# vlan access-map R5 20 S2(config-access-map)# action forward S2(config-access-map)# vlan filter R5 vlan-list 1-51,53-4094 S2(config)#! S2(config)#interface Port-channel1 S2(config-if)# switchport trunk encapsulation dot1q S2(config-if)# switchport mode trunk S2(config-if)#! S2(config-if)#interface FastEthernet0/4 S2(config-if)# switchport access vlan 174 S2(config-if)# switchport mode access S2(config-if)#! S2(config-if)#interface FastEthernet0/5 S2(config-if)# switchport trunk encapsulation isl S2(config-if)# switchport mode trunk S2(config-if)#! S2(config-if)#interface FastEthernet0/12 S2(config-if)# switchport trunk encapsulation dot1q S2(config-if)# switchport mode trunk S2(config-if)#! S2(config-if)#interface FastEthernet0/13 S2(config-if)# switchport trunk encapsulation dot1q S2(config-if)# switchport mode trunk S2(config-if)#! S2(config-if)#interface FastEthernet0/20 S2(config-if)# switchport mode dynamic desirable S2(config-if)# shutdown S2(config-if)#! S2(config-if)#interface FastEthernet0/22 S2(config-if)# switchport trunk encapsulation dot1q S2(config-if)# switchport mode trunk S2(config-if)# channel-group 1 mode desirable S2(config-if)#! S2(config-if)#interface FastEthernet0/23 S2(config-if)# switchport trunk encapsulation dot1q S2(config-if)# switchport mode trunk S2(config-if)# channel-group 1 mode desirable S2(config-if)#! S2(config-if)#interface FastEthernet0/24 S2(config-if)# switchport trunk encapsulation dot1q S2(config-if)# switchport mode trunk S2(config-if)# channel-group 1 mode desirable S2(config-if)#! S2(config-if)#interface Vlan52 S2(config-if)# ip address 172.22.52.9 255.255.255.224 S2(config-if)# no shutdown S2(config-if)#! S2(config-if)#router ospf 1 S2(config-router)# router-id 9.9.9.9 S2(config-router)# log-adjacency-changes S2(config-router)# auto-cost reference-bandwidth 1000 % OSPF: Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers. S2(config-router)# network 172.22.52.9 0.0.0.0 area 1 S2(config-router)#! S2(config-router)#line con 0 S2(config-line)# exec-timeout 0 0 S2(config-line)# privilege level 15 S2(config-line)# logging synchronous S2(config-line)#line vty 0 4 S2(config-line)# password cisco S2(config-line)# login local S2(config-line)#line vty 5 15 S2(config-line)# password cisco S2(config-line)# login local S2(config-line)#! S2(config-line)#end S2#wr Building configuration... 02:43:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to down 02:43:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/12, changed state to down 02:43:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down 02:43:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state t[OK] S2#o down 02:43:28: %SYS-5-CONFIG_I: Configured from console by console 02:43:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down 02:43:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down 02:43:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan52, changed state to up S2# 02:43:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to up 02:43:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/12, changed state to up 02:43:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to up 02:43:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up S2# 02:43:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up 02:43:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up S2# 02:43:32: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up 02:43:33: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel1, changed state to up S2# RACK98AS>10 [Resuming connection 10 to s3 ... ] 02:41:10: S3(config)#hostname S2 S2(config)#! S2(config)#username CISCO password 0 CISCO S2(config)#ip subnet-zero S2(config)#ip routing S2(config)#no ip domain-lookup S2(config)#! S2(config)#! Need to get R5 mac address from Fa0/1 and update this ACL S2(config)#! S2(config)#no mac access-list extended R5 S2(config)# mac access-list extended R5 S2(config-ext-macl)# permit host 001a.6d1a.3e81 any S2(config-ext-macl)#! S2(config-ext-macl)# vlan access-map R5 10 S2(config-access-map)# action drop S2(config-access-map)# match mac address R5 S2(config-access-map)# vlan access-map R5 20 S2(config-access-map)# action forward S2(config-access-map)# vlan filter R5 vlan-list 1-51,53-4094 S2(config)#! S2(config)#interface Port-channel1 S2(config-if)# switchport trunk encapsulation dot1q S2(config-if)# switchport mode trunk S2(config-if)#! S2(config-if)#interface FastEthernet0/4 ^ % Invalid input detected at '^' marker. S2(config)# switchport access vlan 174 ^ % Invalid input detected at '^' marker. S2(config)# switchport mode access ^ % Invalid input detected at '^' marker. S2(config)#! S2(config)#interface FastEthernet0/5 ^ % Invalid input detected at '^' marker. S2(config)# switchport trunk encapsulation isl ^ % Invalid input detected at '^' marker. S2(config)# switchport mode trunk ^ % Invalid input detected at '^' marker. S2(config)#! S2(config)#interface FastEthernet0/12 ^ % Invalid input detected at '^' marker. S2(config)# switchport trunk encapsulation dot1q ^ % Invalid input detected at '^' marker. S2(config)# switchport mode trunk ^ % Invalid input detected at '^' marker. S2(config)#! S2(config)#interface FastEthernet0/13 ^ % Invalid input detected at '^' marker. S2(config)# switchport trunk encapsulation dot1q ^ % Invalid input detected at '^' marker. S2(config)# switchport mode trunk ^ % Invalid input detected at '^' marker. S2(config)#! S2(config)#interface FastEthernet0/20 ^ % Invalid input detected at '^' marker. S2(config)# switchport mode dynamic desirable ^ % Invalid input detected at '^' marker. S2(config)# shutdown % Incomplete command. S2(config)#! S2(config)#interface FastEthernet0/22 ^ % Invalid input detected at '^' marker. S2(config)# switchport trunk encapsulation dot1q ^ % Invalid input detected at '^' marker. S2(config)# switchport mode trunk ^ % Invalid input detected at '^' marker. S2(config)# channel-group 1 mode desirable ^ % Invalid input detected at '^' marker. S2(config)#! S2(config)#interface FastEthernet0/23 ^ % Invalid input detected at '^' marker. S2(config)# switchport trunk encapsulation dot1q ^ % Invalid input detected at '^' marker. S2(config)# switchport mode trunk ^ % Invalid input detected at '^' marker. S2(config)# channel-group 1 mode desirable ^ % Invalid input detected at '^' marker. S2(config)#! S2(config)#interface FastEthernet0/24 ^ % Invalid input detected at '^' marker. S2(config)# switchport trunk encapsulation dot1q ^ % Invalid input detected at '^' marker. S2(config)# switchport mode trunk ^ % Invalid input detected at '^' marker. S2(config)# channel-group 1 mode desirable ^ % Invalid input detected at '^' marker. S2(config)#! S2(config)#interface Vlan52 S2(config-if)# ip address 172.22.52.9 255.255.255.224 S2(config-if)# no shutdown S2(config-if)#! S2(config-if)#router ospf 1 S2(config-router)# router-id 9.9.9.9 S2(config-router)# log-adjacency-changes S2(config-router)# auto-cost reference-bandwidth 1000 % OSPF: Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers. S2(config-router)# network 172.22.52.9 0.0.0.0 area 1 S2(config-router)#! S2(config-router)#line con 0 S2(config-line)# exec-timeout 0 0 S2(config-line)# privilege level 15 S2(config-line)# logging synchronous S2(config-line)#line vty 0 4 S2(config-line)# password cisco S2(config-line)# login local S2(config-line)#line vty 5 15 S2(config-line)# password cisco S2(config-line)# login local S2(config-line)#! S2(config-line)#end S2#wr Building configuration... [OK] S2# 02:45:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan52, changed state to up 02:45:15: %SYS-5-CONFIG_I: Configured from console by console S2# S2# S2# S2# S2#re  wr er Erasing the nvram filesystem will remove all configuration files! Continue? [confirm] [OK] Erase of nvram: complete S2# 02:45:50: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram S2#reload Proceed with reload? [confirm] RACK98AS>11 [Resuming connection 11 to s4 ... ] 02:43:02: % S4(config)# 02:45:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/15, changed state to down 02:45:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/16, changed state to down 02:45:29: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to down S4(config)# 02:45:30: %LINK-3-UPDOWN: Interface GigabitEthernet0/16, changed state to down S4(config)#! S4(config)#hostname S4 S4(config)#! S4(config)#! S4(config)#username CISCO password 0 CISCO S4(config)#no aaa new-model S4(config)#ip subnet-zero S4(config)#no ip domain-lookup S4(config)#! S4(config)#interface GigabitEthernet0/12 S4(config-if)# switchport trunk encapsulation dot1q S4(config-if)# switchport mode trunk S4(config-if)#! S4(config-if)#interface GigabitEthernet0/13 S4(config-if)# switchport trunk encapsulation dot1q S4(config-if)# switchport mode trunk S4(config-if)#! S4(config-if)#interface GigabitEthernet0/15 S4(config-if)# switchport trunk encapsulation dot1q S4(config-if)# switchport mode trunk S4(config-if)#! S4(config-if)#interface GigabitEthernet0/16 S4(config-if)# switchport trunk encapsulation dot1q S4(config-if)# switchport mode trunk S4(config-if)#! S4(config-if)#interface GigabitEthernet0/20 S4(config-if)# shutdown S4(config-if)#! S4(config-if)#line con 0 S4(config-line)# exec-timeout 0 0 S4(config-line)# privilege level 15 S4(config-line)# logging synchronous S4(config-line)#line vty 0 4 S4(config-line)# password cisco S4(config-line)# login local S4(config-line)#line vty 5 15 S4(config-line)# password cisco S4(config-line)# login local S4(config-line)#! S4(config-line)#end S4#wr Building configuration... [OK] S4# 02:46:29: %SYS-5-CONFIG_I: Configured from console by console S4# RACK98AS>210   10 [Resuming connection 10 to s3 ... ] 02:45:55: %SYS-5-RE@@@@@@@@@@@@@@ File "flash:/c3560-ipservices-mz.122-25.SEE2/c3560-advipservicesk9-mz.122-25.SEE2.bin" uncompressed and installed, entry point: 0x3000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Fri 28-Jul-06 12:34 by yenanh Image text-base: 0x00003000, data-base: 0x012237D0 Initializing flashfs... flashfs[1]: 400 files, 6 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 32514048 flashfs[1]: Bytes used: 9688064 flashfs[1]: Bytes available: 22825984 flashfs[1]: flashfs fsck took 6 seconds. flashfs[1]: Initialization complete....done Initializing flashfs. front_end/ (directory) extracting front_end/fe_type_1 (34696 bytes) extracting front_end/fe_type_2 (54584 bytes) extracting front_end/front_end_ucode_info (86 bytes) extracting ucode_info (76 bytes) POST: CPU MIC register Tests : Begin POST: CPU MIC register Tests : End, Status Passed POST: PortASIC Memory Tests : Begin POST: PortASIC Memory Tests : End, Status Passed POST: CPU MIC PortASIC interface Loopback Tests : Begin POST: CPU MIC PortASIC interface Loopback Tests : End, Status Passed POST: PortASIC RingLoopback Tests : Begin POST: PortASIC RingLoopback Tests : End, Status Passed RACK98AS>8 [Resuming connection 8 to s1 ... ] 02:41:22: %LINEPROTO S1#conf t Enter configuration commands, one per line. End with CNTL/Z. S1(config)#clust S1(config)#cluster ? commander-address configures cluster commander address discovery cluster discovery config enable configures cluster commander holdtime configures cluster heartbeat holdtime member configures a cluster member outside-interface configures cluster outside interface run This will enable clustering on the device standby-group HSRP group name timer configures cluster heartbeat interval S1(config)#cluster en S1(config)#cluster enable ? WORD cluster name S1(config)#cluster enable CCIE ? <0-15> commander member number S1(config)#cluster enable CCIE S1(config)#cluster mn=   meme S1(config)#cluster meme  S1(config)#cluster member ma S1(config)#cluster member mac-address RACK98AS>9 [Resuming connection 9 to s2 ... ] 02:45:54: %LINEPROTO- S2#sh ver Cisco IOS Software, C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Fri 28-Jul-06 12:20 by yenanh Image text-base: 0x00003000, data-base: 0x00DC0AC4 ROM: Bootstrap program is C3550 boot loader S2 uptime is 2 hours, 47 minutes System returned to ROM by power-on System image file is "flash:/c3550-ipservices-mz.122-25.SEB4/c3550-ipservicesk9-mz.122-25.SEE2.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. --More--  A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. Cisco WS-C3550-24 (PowerPC) processor (revision R0) with 65526K/8192K bytes of memory. Processor board ID CAT1018N161 Last reset from warm-reset Running Layer2/3 Switching Image Ethernet-controller 1 has 12 Fast Ethernet/IEEE 802.3 interfaces Ethernet-controller 2 has 12 Fast Ethernet/IEEE 802.3 interfaces Ethernet-controller 3 has 1 Gigabit Ethernet/IEEE 802.3 interface Ethernet-controller 4 has 1 Gigabit Ethernet/IEEE 802.3 interface 24 FastEthernet interfaces 2 Gigabit Ethernet interfaces --More--  The password-recovery mechanism is enabled. 384K bytes of flash-simulated NVRAM. Base ethernet MAC Address: 00:17:E0:6F:14:80 Motherboard assembly number: 73-5700-12 Power supply part number: 34-0966-04 Motherboard serial number: CAT10171Y0X Power supply serial number: DTH10156X53 Model revision number: R0 Motherboard revision number: A0 Model number: WS-C3550-24-EMI System serial number: CAT1018N161 Configuration register is 0x10F S2# RACK98AS>8 [Resuming connection 8 to s1 ... ] 00:17:E0:6F:14:80 S1(config)#cluster member mac-address 00:17:E0:6F:14:80                  RACK98AS>10 [Resuming connection 10 to s3 ... ] POST: POST: PortASIC CAM Subsystem Tests : End, Status Passed POST: PortASIC Port Loopback Tests : Begin POST: PortASIC Port Loopback Tests : End, Status Passed Waiting for Port download...Complete This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco WS-C3560G-24PS (PowerPC405) processor (revision F0) with 118784K/12280K bytes of memory. Processor board ID FOC1051Y642 Last reset from power-on 1 Virtual Ethernet interface 28 Gigabit Ethernet interfaces The password-recovery mechanism is enabled. 512K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : 00:1A:A2:1B:E3:80 Motherboard assembly number : 73-10213-04 Power supply part number : 341-0108-03 Motherboard serial number : FOC105122KS Power supply serial number : DCA1046A248 Model revision number : F0 Motherboard revision number : B0 Model number : WS-C3560G-24PS-E System serial number : FOC1051Y642 Top Assembly Part Number : 800-27478-01 Top Assembly Revision Number : A0 Version ID : V05 CLEI Code Number : CNMW300ARC Hardware Board Revision Number : 0x09 Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 28 WS-C3560G-24PS 12.2(25)SEE2 C3560-ADVIPSERVICESK RACK98AS>8 [Resuming connection 8 to s1 ... ] 00:1A:A2:1B:E3:80 RACK98AS>10 [Resuming connection 10 to s3 ... ]  Press RETURN to get started! 00:01:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down 00:01:32: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan 00:01:53: %SYS-5-RESTART: System restarted -- Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Fri 28-Jul-06 12:34 by yenanh 00:01:55: %LINK-3-UPDOWN: Interface GigabitEthernet0/12, changed state to up 00:01:55: %LINK-3-UPDOWN Would you like to terminate autoinstall? [yes]: --- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: % Please answer 'yes' or 'no'. Would you like to enter the initial configuration dialog? [yes/no]: % Please answer 'yes' or 'no'. Would you like to enter the initial configuration dialog? [yes/no]: : Interface GigabitEthernet0/13, changed state to up 00:01:55: %LINK-3-UPDOWN: Interface GigabitEthernet0/14, changed state to up 00:01:58: %DTP-5-DOMAINMISMATCH: Unable to perform trunk negotiation on port Gi0/20 because of VTP domain mismatch. 00:01:59: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/14, changed state to up 00:01:59: %LINK-3-UPDOWN: Interface GigabitEthernet0/16, changed state to up 00:01:59: %LINK-3-UPDOWN: Interface GigabitEthernet0/20, changed state to up 00:01:59: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to up 00:02:00: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up 00:02:00: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/13, changed state to up 00:02:00: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/20, changed state to up Switch>en Switch# Switch# 00:02:02: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/16, changed state to up 00:02:02: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/15, changed state to upconf t Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#! Switch(config)#hostname S3 S3(config)#username CISCO password 0 CISCO S3(config)#no aaa new-model S3(config)#ip subnet-zero S3(config)#no ip domain-lookup S3(config)#! S3(config)#! S3(config)#interface GigabitEthernet0/12 S3(config-if)# switchport trunk encapsulation dot1q S3(config-if)# switchport mode trunk S3(config-if)#! S3(config-if)#interface GigabitEthernet0/13 S3(config-if)# switchport trunk encapsulation dot1q S3(config-if)# switchport mode trunk S3(config-if)#! S3(config-if)#interface GigabitEthernet0/15 S3(config-if)# switchport trunk encapsulation dot1q S3(config-if)# switchport mode trunk S3(config-if)#! S3(config-if)#interface GigabitEthernet0/16 S3(config-if)# switchport trunk encapsulation dot1q S3(config-if)# switchport mode trunk S3(config-if)#! S3(config-if)#interface GigabitEthernet0/20 S3(config-if)# shutdown S3(config-if)#! S3(config-if)#line con 0 S3(config-line)# exec-timeout 0 0 S3(config-line)# privilege level 15 S3(config-line)# logging synchronous S3(config-line)#line vty 0 4 S3(config-line)# password cisco S3(config-line)# login local S3(config-line)#line vty 5 15 S3(config-line)# password cisco S3(config-line)# login local S3(config-line)#! S3(config-line)#end S3#wr Building configuration... [OK] S3# 00:02:11: %SYS-5-CONFIG_I: Configured from console by console 00:02:12: %LINK-5-CHANGED: Interface GigabitEthernet0/20, changed state to administratively down S3# RACK98AS>8 [Resuming connection 8 to s1 ... ] 02:49:03: %LINK-3-U %ERROR: member unreachable S1(config)#cluster member mac-address 00:1A:A2:1B:E3:80 S1(config)#cluster member mac-address 00:1A:A2:1B:E3:80                  RACK98AS>11 [Resuming connection 11 to s4 ... ] 02:48:34: %LINK- S4#sh ver Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Fri 28-Jul-06 12:34 by yenanh Image text-base: 0x00003000, data-base: 0x012237D0 ROM: Bootstrap program is C3560 boot loader BOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SEE4, RELEASE SOFTWARE (fc1) S4 uptime is 2 hours, 49 minutes System returned to ROM by power-on System image file is "flash:/c3560-ipservices-mz.122-25.SEE2/c3560-advipservicesk9-mz.122-25.SEE2.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable --More--  to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco WS-C3560G-24PS (PowerPC405) processor (revision F0) with 118784K/12280K bytes of memory. Processor board ID FOC1051Y629 Last reset from power-on 1 Virtual Ethernet interface 28 Gigabit Ethernet interfaces The password-recovery mechanism is enabled. 512K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : 00:1A:A2:1B:E3:00 Motherboard assembly number : 73-10213-04 Power supply part number : 341-0108-03 Motherboard serial number : FOC105122JD Power supply serial number : DCA1046A22X Model revision number : F0 --More--  Motherboard revision number : B0 Model number : WS-C3560G-24PS-E System serial number : FOC1051Y629 Top Assembly Part Number : 800-27478-01 Top Assembly Revision Number : A0 Version ID : V05 CLEI Code Number : CNMW300ARC Hardware Board Revision Number : 0x09 Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 28 WS-C3560G-24PS 12.2(25)SEE2 C3560-ADVIPSERVICESK Configuration register is 0xF S4# RACK98AS>8 [Resuming connection 8 to s1 ... ] 00:1A:A2:1B:E3:00 S1(config)# S1(config)#cluster member mac-address 00:1A:A2:1B:E3:00 cluster member mac-address 00:1A:A2:1B:E3:0000:1A:A2:1B:E3:00 ^ % Invalid input detected at '^' marker. S1(config)#^Z S1#wr Building configuration... [OK] S1# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1(config)#! R1(config)#hostname R1 R1(config)#ip cef R1(config)#no ip domain lookup R1(config)#! R1(config)#ipv6 unicast-routing R1(config)#! R1(config)#username R5 password 0 BluesBrothers R1(config)#! R1(config)#interface Loopback0 R1(config-if)# ip address 172.22.81.1 255.255.255.0 R1(config-if)#! R1(config-if)#interface Loopback1 R1(config-if)# no ip address R1(config-if)# ipv6 address 2006:1:1::/128 R1(config-if)# ipv6 ospf 1 area 0 R1(config-if)#! R1(config-if)#interface Loopback2 R1(config-if)# description To inject into OSPFv3 for the prefix to R5 R1(config-if)# ip address 199.199.199.1 255.255.255.0 R1(config-if)#! R1(config-if)#interface Loopback100 R1(config-if)# description for BGP announce R1(config-if)# ip address 131.108.1.1 255.255.255.0 R1(config-if)#! R1(config-if)#interface FastEthernet0/0 R1(config-if)# ip address 172.22.174.1 255.255.255.192 R1(config-if)# ip policy route-map Telnet-PBR R1(config-if)# duplex auto R1(config-if)# speed auto R1(config-if)#! R1(config-if)#interface Serial0/0 R1(config-if)# no ip address R1(config-if)# encapsulation frame-relay R1(config-if)#! R1(config-if)#interface Serial0/0.1 multipoint R1(config-subif)# bandwidth 128 R1(config-subif)# ip address 172.22.142.1 255.255.255.0 R1(config-subif)# ip ospf message-digest-key 1 md5 CISCO R1(config-subif)# ip ospf network point-to-multipoint R1(config-subif)# ip ospf hello-interval 60 R1(config-subif)# ipv6 address 2005:124:124::1/64 R1(config-subif)# ipv6 address FE80::1 link-local R1(config-subif)# ipv6 nat R1(config-subif)# ipv6 ospf network point-to-point R1(config-subif)# ipv6 ospf 1 area 124 R1(config-subif)# frame-relay map ipv6 FE80::2 122 broadcast R1(config-subif)# frame-relay map ip 172.22.142.1 122 R1(config-subif)# frame-relay map ip 172.22.142.2 122 broadcast R1(config-subif)# frame-relay map ip 172.22.142.4 122 R1(config-subif)# frame-relay map ipv6 2005:124:124::2 122 broadcast R1(config-subif)# frame-relay map ipv6 2005:124:124::4 122 R1(config-subif)#! R1(config-subif)#interface Serial0/0.2 point-to-point R1(config-subif)# frame-relay interface-dlci 125 ppp Virtual-Template1 R1(config-fr-dlci)#! R1(config-fr-dlci)#interface FastEthernet0/1 R1(config-if)# shutdown R1(config-if)#! R1(config-if)#interface Serial0/1 R1(config-if)# shutdown R1(config-if)#! R1(config-if)#interface Virtua 02:47:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up 02:47:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback2, changed state to up 02:47:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback100, changed state to up 02:47:19: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to upl-Template1 R1(config-if)# bandwidth 64 R1(config-if)# ip address 172.22.51.1 255.255.255.252 R1(config-if)# ip bandwidth-percent eigrp 174 100 R1(config-if)# 02:47:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up ip hello-interval eigrp 174 10 R1(config-if)# ip hold-time eigrp 174 30 R1(config-if)# ipv6 nat R1(config-if)# ppp authentication chap R1(config-if)#! R1(config-if)#router eigrp 174 R1(config-router)# redistribute ospf 1 metric 32 2000 255 1 1500 route-map No$te ospf 1 metric 32 2000 255 1 1500 route-map NoE igrp R1(config-router)# passive-interface Serial0/0 R1(config-router)# passive-interface Loopback0 R1(config-router)# network 172.22.0.0 R1(config-router)# network 199.199.199.1 0.0.0.0 R1(config-router)# distance eigrp 90 90 R1(config-router)# no auto-summary R1(config-router)# eigrp router-id 172.22.81.1 R1(config-router)#! R1(config-router)#router ospf 1 R1(config-router)# router-id 1.1.1.1 R1(config-router)# log-adjacency-changes R1(config-router)# auto-cost reference-bandwidth 1000 % OSPF: Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers. R1(config-router)# area 0 authentication message-digest R1(config-router)# timers throttle spf 5000 60000 60000 R1(config-router)# redistribute eigrp 174 metric 10000 metric-type 1 subnets R1(config-router)# network 172.22.142.1 0.0.0.0 area 0 R1(config-router)# distance ospf external 89 R1(config-router)#! R1(config-router)#router bgp 124 R1(config-router)# no synchronization R1(config-router)# bgp router-id 1.1.1.1 R1(config-router)# bgp log-neighbor-changes R1(config-router)# bgp confederation identifier 4321 R1(config-router)# bgp confederation peers 300 R1(config-router)# timers bgp 300 900 R1(config-router)# redistribute connected route-map intoBGP R1(config-router)# neighbor 172.22.82.1 remote-as 124 R1(config-router)# neighbor 172.22.82.1 update-source Loopback0 R1(config-router)# neighbor 172.22.82.1 advertisement-interval 300 R1(config-router)# no auto-summary R1(config-router)#! R1(config-router)#ip access-list standard R6Loop0 R1(config-std-nacl)# permit 172.22.86.0 R1(config-std-nacl)#! R1(config-std-nacl)#ip access-list extended Telnet-PBR R1(config-ext-nacl)# permit tcp host 172.22.87.1 host 172.22.82.1 eq telnet R1(config-ext-nacl)# permit tcp host 172.22.87.1 eq telnet host 172.22.82.1 R1(config-ext-nacl)#! R1(config-ext-nacl)#ipv6 router ospf 1 R1(config-rtr)# router-id 1.1.1.1 R1(config-rtr)# log-adjacency-changes R1(config-rtr)# area 124 virtual-link 4.4.4.4 R1(config-rtr)# distribute-list prefix-list NATPT out connected R1(config-rtr)# redistribute connected R1(config-rtr)#! R1(config-rtr)#ipv6 nat v4v6 source 172.22.52.5 2006:5:5::5 R1(config)#ipv6 nat v6v4 source list NATPT pool MyPool R1(config)#ipv6 nat v6v4 pool MyPool 199.199.199.2 199.199.199.100 prefix-len$v4 pool MyPool 199.199.199.2 199.199.199.100 prefix-leng th 24 R1(config)#ipv6 nat prefix 2006:5:5::/96 R1(config)#! R1(config)#! R1(config)#ipv6 prefix-list NATPT seq 5 permit 2006:5:5::/96 R1(config)#route-map intoBGP permit 10 R1(config-route-map)# match interface Loopback100 R1(config-route-map)#! R1(config-route-map)#route-map Telnet-PBR permit 10 R1(config-route-map)# match ip address Telnet-PBR R1(config-route-map)# set ip next-hop 172.22.51.2 R1(config-route-m 02:47:28: %OSPFv3-3-RECONF_VL: OSPF process 1 is changing router-id. Reconfigure virtual link neighbors with our new router-idap)#! R1(config-route-map)#route-map NoEigrp permit 10 R1(config-route-map)# match ip address R6Loop0 R1(config-route-map)#! R1(config-route-map)#route-map NoEigrp deny 20 R1(config-route-map)# match tag 6 R1(config-route-map)#! R1(config-route-map)#route-map NoEigrp permit 30 R1(config-route-map)#! R1(config-route-map)#ipv6 access-list NATPT R1(config-ipv6-acl)# 5 02:47:29: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.174.8 (FastEthernet0/0) is up: new adjacency R1(config-ipv6-acl)# 5  02:47:36: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.174.8 (FastEthernet0/0) is down: route configuration changed R1(config-ipv6-acl)# 02:47:38: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.174.8 (FastEthernet0/0) is up: new adjacency R1(config-ipv6-acl)# permit ipv6 any any R1(config-ipv6-acl)#! R1(config-ipv6-acl)#line con 0 R1(config-line)# exec-timeout 0 0 R1(config-line)# privilege level 15 R1(config-line)# logging synchronous R1(config-line)#line aux 0 R1(config-line)#line vty 0 4 R1(config-line)# password cisco R1(config-line)# login R1(config-line)#line vty 5 15 R1(config-line)# password cisco R1(config-line)# login R1(config-line)#! R1(config-line)#end R1#wr Building configuration... RACK98AS>2 [Resuming connection 2 to r2 ... ] R2(config)#! R2(config)#hostname R2 R2(config)#! R2(config)#ip cef R2(config)#! R2(config)#no ip domain lookup R2(config)#! R2(config)#ipv6 unicast-routing R2(config)#! R2(config)#interface Loopback0 R2(config-if)# ip address 172.22.82.1 255.255.255.128 R2(config-if)# ip rip advertise 60 R2(config-if)# ip ospf 1 area 0 R2(config-if)#! R2(config-if)#interface Loopback1 R2(config-if)# no ip address R2(config-if)# ipv6 address 2006:2:2::/128 R2(config-if)# ipv6 rip R2 enable R2(config-if)#! R2(config-if)#interface Tunnel0 R2(config-if)# no ip address R2(config-if)# ipv6 address 2005:26:26::2/64 R2(config-if)# ipv6 rip R2 enable R2(config-if)# keepalive 10 3 R2(config-if)# tunnel source Serial0/2 R2(config-if)# tunnel destination 172.22.62.6 R2(config-if)# tunnel mode ipv6ip R2(config-if)# no shutdown R2(config-if)#! R2(config-if)#interface FastEthernet0/0 R2(config-if)# ip address 172.22.52.2 255.255.255.224 R2(config-if)# ip rip advertise 60 R2(config-if)# ip ospf 1 area 1 R2(config-if)# speed auto R2(config-if)# duplex auto R2(config-if)# no shutdown R2(config-if)#! R2(config-if)#interface Serial0/0 R2(config-if)# no ip address R2(config-if)# encapsulation frame-relay R2(config-if)# no fair-queue R2(config-if)# no frame-relay inverse-arp R2(config-if)# no shutdown R2(config-if)#! R2(config-if)#interface Serial0/0.1 point-to-point R2(config-subif)# ip address 172.22.32.2 255.255.255.0 R2(config-subif)# ip rip advertise 60 R2(config-subif)# ipv6 address 2005:23:23::2/64 R2(config-subif)# ipv6 address FE80::2 link-local R2(config-subif)# ipv6 ospf network non-broadcast R2(config-subif)# ipv6 ospf 1 area 23 R2(config-subif)# frame-relay interface-dlci 223 R2(config-fr-dlci)# 02:49:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up 02:49:07: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up no shutdown R2(config-subif)#! R2(config-subif)#interface Serial0/0.2 multipoint R2(config-subif)# ip address 172.22.142.2 255.255.255.0 R2(config-subif)# ip rip advertise 60 R2(config-subif)# ip ospf message-digest-key 1 md5 CISCO R2(config-subif)# ip ospf network point-to-multipoint R2(config-subif)# ip ospf hello-interval 60 R2(config-subif)# ip ospf 1 area 0 R2(config-subif)# ipv6 address 2005:124:124::2/64 R2(config-subif)# ipv6 address FE80::2 link-local R2(config-subif)# ipv6 ospf network point-to-multipoint R2(config-subif)# ipv6 ospf hello 10 R2(config-subif)# ipv6 ospf 1 area 124 R2(config-subif)# frame-relay map ipv6 FE80::4 224 broadcast R2(config-subif)# frame-relay map ip 172.22.142.1 221 broadcast R2(config-subif)# frame-relay map ip 172.22.142.4 224 broadcast R2(config-subif)# frame-relay map ipv6 2005:124:124::1 221 broadcast R2(config-subif)# frame-relay map ipv6 2005:124:124::4 224 broadcast R2(config-subif)# frame-relay map ipv6 FE80::1 221 broadcast R2(config-subif)# no shutdown R2(config-subif)#! R2(config-subif)#interface FastEthernet0/1 R2(config-if)# shutdown R2(config-if)#! R2(config-if)#interface Serial0/1 R2(config-if)# shutdown R2(config-if)#! R2(config-if)#interface Serial0/2 R2(config-if)# ip address 172.22.62.2 255.255.255.0 R2(config-if)# ip rip advertise 60 R2(config-if)# clock rate 128000 R2(config-if)# no shutdown R2(config-if)#! R2(config-if)#router ospf 1 R2(config-router)# router-id 2.2.2.2 Reload or use "clear ip ospf process" command, for this to take effect R2(config-router)# log-adjacency-changes R2(config-router)# auto-cost reference-bandwidth 1000 % OSPF: Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers. R2(config-router)# area 0 authentication message-digest R2(config-router)# area 0 range 172.22.84.0 255.255.254.0 R2(config-router)# area 1 virtual-link 5.5.5.5 message-digest-key 1 md5 CISCO R2(config-router)# timers throttle spf 6000 6000 6000 R2(config-router)# redistribute rip metric-type 1 subnets tag 2 route-map Fro$te rip metric-type 1 subnets tag 2 route-map From R6 R2(config-router)# distance ospf external 121 R2(config-router)#! R2(config-router)#router rip R2(config-router)# version 2 R2(config-router)# timers basic 60 240 240 300 R2(config-router)# redistribute ospf 1 metric 2 R2(config-router)# passive-interface FastEthernet0/0 R2(config-router)# passive-interface Serial0/0.2 R2(config-router)# output-delay 24 R2(config-router)# network 172.22.0.0 R2(config-router)# distribute-list 100 in Serial0/2 R2(config-router)# no auto-summary R2(config-router)#! R2(config-router)#router bgp 124 R2(config-router)# no synchronization R2(config-router)# bgp router-id 2.2.2.2 R2(config-router)# bgp log-neighbor-changes R2(config-router)# bgp confederation identifier 4321 R2(config-router)# bgp confederation peers 300 R2(config-router)# bgp dampening route-map R3Routes R2(config-router)# timers bgp 300 900 R2(config-router)# neighbor 172.22.32.3 remote-as 300 R2(config-router)# neighbor 172.22.81.1 remote-as 124 R2(config-router)# neighbor 172.22.81.1 update-source Loopback0 R2(config-router)# neighbor 172.22.81.1 route-reflector-client R2(config-router)# neighbor 172.22.142.4 remote-as 124 R2(config-router)# neighbor 172.22.142.4 route-reflector-client R2(config-router)# no auto-summary R2(config-router)#! R2(config-router)#ip access-list standard R6 R2(config-std-nacl)# permit 172.22.62.6 R2(config-std-nacl)#! R2(config-std-nacl)#ip prefix-list R3Routes seq 5 permit 172.22.33.0/24 R2(config)#ip prefix-list R3Routes seq 10 permit 172.22.83.0/24 R2(config)#! R2(config)#access-list 100 deny ip host 172.22.62.6 0.1.1.0 255.254.254.255 R2(config)#access-list 100 permit ip any any R2(config)#ipv6 router ospf 1 R2(config-rtr)# router-id 2.2.2.2 R2(config-rtr)# log-adjacency-changes R2(config-rtr)# redistribute rip R2 include-connected R2(config-rtr)#! R2(config-rtr)#ipv6 router rip R2 R2(config-rtr)# redistribute connected R2(config-rtr)# redistribute ospf 1 metric 2 R2(config-rtr)#! R2(config-rtr)#route-map R3Routes permit 10 R2(config-route-map)# match ip address prefix-list R3Routes R2(config-route-map)# set dampening 15 750 4000 60 R2(config-route-map)#! R2(config-route-map)#route-map R3Routes permit 20 R2(config-route-map)#! R2(config-route-map)#route-map FromR6 permit 10 R2(config-route-map)# match ip route-source R6 R2(config-route-map)# match metric 1 R2(config-route-map)# set tag 6 R2(config-route-map)#! R2(config-route-map)#route-map FromR6 permit 20 R2(config-route-map)#! R2(config-route-map)#line con 0 R2(config-line)# exec-timeout 0 0 R2(config-line)# privilege level 15 R2(config-line)# logging synchronous R2(config-line)#line aux 0 R2(config-line)#line vty 0 4 R2(config-line)# password cisco R2(config-line)# loine vty 5 15 ^ % Invalid input detected at '^' marker. R2(config-line)# password 02:49:12: %OSPF-5-ADJCHG: Process 1, Nbr 9.9.9.9 on FastEthernet0/0 from LOADING to FULL, Loading Done 02:49:12: %OSPFv3-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Serial0/0.2 from LOADING to FULL, Loading Done R2(config-line)# passwordloine vty 5 15password ciscoloine vty 5 15 02:49:21: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Serial0/0.2 from LOADING to FULL, Loading Done R2(config-line)# loine vty 5 15ine vty 5 15  R2(config-line)# line vty 5 15oine vty 5 15password ciscoloine vty 5 15ine vty 5 15   line vty 5 15oine vty 5 15 02:49:27: %BGP-5-ADJCHANGE: neighbor 172.22.81.1 Up R2(config-line)# loine vty 5 15password cisco R2(config-line)#login R2(config-line)#^Z R2#wr Building configuration... RACK98AS>3 [Resuming connection 3 to r3 ... ] R3(config)#! R3(config)#hostname R3 R3(config)#ip cef R3(config)#! R3(config)#! R3(config)#no ip domain lookup R3(config)#! R3(config)#ipv6 unicast-routing R3(config)#! R3(config)#interface Loopback0 R3(config-if)# ip address 172.22.83.1 255.255.255.0 R3(config-if)# ip rip advertise 60 R3(config-if)#! R3(config-if)#interface Loopback1 R3(config-if)# no ip address R3(config-if)# ipv6 address 2006:3:3::/128 R3(config-if)# ipv6 ospf 1 area 0 R3(config-if)#! R3(config-if)#interface Tunnel0 R3(config-if)# no ip address R3(config-if)# ipv6 address 2005:34:34::3/64 R3(config-if)# ipv6 ospf 1 area 0 R3(config-if)# keepalive 10 3 R3(config-if)# tunnel source Loopback0 R3(config-if)# tunnel destination 172.22.84.1 R3(config-if)# tunnel mode ipv6ip R3(config-if)# no shutdown R3(config-if)#! R3(config-if)#interface FastEthernet0/0 R3(config-if)# ip address 172.22.33.3 255.255.255.0 R3(config-if)# ip rip advertise 60 R3(config-if)# speed auto R3(config-if)# duplex auto R3(config-if)# ipv6 address 2005:3:3::3/64 R3(config-if)# ipv6 ospf 1 area 23 R3(config-if)# no shutdown R3(config-if)#! R3(config-if)#interface FastEthernet0/1 R3(config-if)# shutdown R3(config-if)#! R3(config-if)#interface Serial0/0/0 R3(config-if)# ip address 172.22.32.3 255.255.255.0 R3(config-if)# ip rip advertise 60 R3(config-if)# encapsulation frame-relay R3(config-if)# ipv6 address 2005:23:23::3/64 R3(config-if)# ipv6 address FE80::3 link-local R3(config-if)# ipv6 ospf neighbor FE80::2 R3(config-if)# ipv6 ospf 1 area 23 R3(config-if)# traffic-shape rate 128000 32000 32000 1000 R3(config-if)# traffic-shape adaptive 96000 R3(config-if)# frame-relay map ipv6 FE80::2 322 broadcast R3(config-if)# frame-relay map ip 172.22.32.2 322 broadcast R3(config-if)# frame-relay map ipv6 2005:23:23::2 322 broadcast R3(config-if)# no frame-relay inverse-arp R3(config-if)# no shutdown R3(config-if)#! R3(config-if)#interface Serial0/0/1 R3(config-if)# shutdown R3(config-if)#! R3(config-if)#interface Serial0/1/0 R3(config-if)# ip address 172.22.63.3 255.255.255.0 R3(config-if)# ip rip advertise 60 R3(config-if)# clock rate 128000 R3(config-if)# no shutdown R3(config-if)#! R3(config-if)#router rip R3(config-router)# version 2 R3(config-router)# timers basic 60 240 240 300 R3(config-router)# passive-interface FastEthernet0/0 R3(config-router)# output-delay 24 R3(config-router)# network 17 02:55:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up 02:55:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down2.22.0.0 R3(config-router)# neighbor 172.22.33.44 R3(config-router)# distribute-list 100 in Serial0/1/0 R3(config-router)# distance 255 R3(config-router)# distance 120 172.22.33.44 0.0.0.0 R3(config-router)# distance 120 172.22.32.2 0.0.0.0 R3(config-router)# distance 120 172.22.63.6 0.0.0.0 R3(config-router)# no auto-summary R3(config-router)#! R3(config-router)#router bgp 300 R3(config-router)# no synchronization R3(config-router)# bgp router-id 3.3.3.3 R3(config-router)# bgp log-neighbor-changes R3(config-router)# bgp confederation identifier 4321 R3(config-router)# bgp confederation peers 124 R3(config-router)# bgp dampening route-map Multicast R3(config-router)# aggregate-address 215.7.0.0 255.255.240.0 summary-only R3(config-router)# redistribute connected R3(config-router)# neighbor 172.22.32.2 remote-as 124 R3(config-router)# neighbor 172.22.32.2 filter-list 1 out R3(config-router)# neighbor 172.22.63.6 remote-as 600 R3(config-router)# neighbor 172.22.63.6 send-community R3(config-router)# neighbor 172.22.63.6 route-map 200route in R3(config-router)# neighbor 172.22.63.6 route-map PodLoops out R3(config-router)# neighbor 172.22.142.4 remote-as 124 R3(config-router)# neighbor 172.22.142.4 ebgp-multihop 2 R3(config-router)# neighbor 172.22.142.4 filter-list 1 out R3(config-router)# no auto-summary R3(config-router)#! R3(config-router)#ip as-path access-list 1 permit _4000(_0-9+)*_7000$ R3(config)#ip as-path access-list 1 permit _(1000|7000)_ R3(config)#ip as-path access-list 1 deny _4000_ R3(config)#ip as-path access-list 1 permit _1000$ R3(config)#ip as-path access-list 1 permit _900$ R3(config)#ip as-path access-list 1 permit ^$ R3(config)#! R3(config)#no ip http server R3(config)#no ip http secure-server R3(config)#! R3(config)#ip prefix-list 200route seq 5 permit 200.1.0.0/16 R3(config)#! R3(config)#ip prefix-list Multicast seq 5 permit 224.0.0.0/4 le 32 R3(config)#! R3(config)#ip prefix-list PodLoops seq 5 permit 172.22.83.0/24 R3(config)#ip prefix-list PodLoops seq 10 permit 172.22.82.0/24 R3(config)#ip prefix-list PodLoops seq 15 permit 172.22.84.0/24 R3(config)#access-list 100 deny ip host 172.22.63.6 0.1.1.0 255.254.254.255 R3(config)#access-list 100 permit ip any any R3(config)#ipv6 router ospf 1 R3(config-rtr)# router-id 3.3.3.3 R3(config-rtr)# log-adjacency-changes R3(config-rtr)#! R3(config-rtr)#route-map PodLoops permit 10 R3(config-route-map)# match ip address prefix-list PodLoops R3(config-route-map)# set community no-export R3(config-route-map)#! R3(config-route-map)#route-map 200route permit 10 R3(config-route-map)# set as-path prepend 550 500 450 R3(config-route-map)#! R3(config-route-map)#route-map 200route permit 20 R3(config-route-map)#! R3(config-route-map)#route-map Multicast permit 10 R3(config-route-map)# match ip address prefix-list Multicast R3(config-route-map)# set dampening 5 500 999 5 R3(config-route-map)#! R3(config-route-map)#route-map Multicast permit 20 R3(config-route-map)#! R3(config-route-map)#line con 0 R3(config-line)# exec-timeout 0 0 R3(config-line)# privilege level 15 R3(config-line)# logging synchronous R3(config-line)#line aux 0 R3(config-line)#line vty 0 4 R3(config-line)# password cisco R3(config-line)# login R3(config-line)#line vty 5 15 R3(config-line)# password cisco R3(config-line)# login R3(config-line)#! R3(config-line)#end R3#wr Building configuration... [OK] R3# 02:55:20: %SYS-5-CONFIG RACK98AS>4 [Resuming connection 4 to r4 ... ] R4(config)#! R4(config)#hostname R4 R4(config)#! R4(config)#ip cef R4(config)#! R4(config)#no ip domain lookup R4(config)#! R4(config)#ipv6 unicast-routing R4(config)#! R4(config)#class-map match-all af13 R4(config-cmap)# match ip dscp af13 R4(config-cmap)#class-map match-all af22 R4(config-cmap)# match ip dscp af22 R4(config-cmap)#class-map match-all prec1 R4(config-cmap)# match ip precedence 1 R4(config-cmap)#class-map match-all prec2 R4(config-cmap)# match ip precedence 2 R4(config-cmap)#! R4(config-cmap)#policy-map test R4(config-pmap)# class af22 R4(config-pmap-c)# class af13 R4(config-pmap-c)# class prec1 R4(config-pmap-c)# class prec2 R4(config-pmap-c)#! R4(config-pmap-c)#interface Loopback0 R4(config-if)# ip address 172.22.84.1 255.255.255.0 R4(config-if)# ip ospf 1 area 0 R4(config-if)#! R4(config-if)#interface Loopback1 R4(config-if)# no ip address R4(config-if)# ipv6 address 2006:4:4::/128 R4(config-if)# ipv6 ospf 1 area 0 R4(config-if)#! R4(config-if)#interface Tunnel0 R4(config-if)# no ip address R4(config-if)# ipv6 address 2005:34:34::4/64 R4(config-if)# ipv6 ospf 1 area 0 R4(config-if)# keepalive 10 3 R4(config-if)# tunnel source Loopback0 R4(config-if)# tunnel destination 172.22.83.1 R4(config-if)# tunnel mode ipv6ip R4(config-if)# no shutdown R4(config-if)#! R4(config-if)#interface FastEthernet0/0 R4(config-if)# shutdown R4(config-if)#! R4(config-if)#interface FastEthernet0/1 R4(config-if)# ip address 172.22.174.4 255.255.255.192 R4(config-if)# speed auto R4(config-if)# duplex auto R4(config-if)# service-policy input test R4(config-if)# no shutdown R4(config-if)#! R4(config-if)#interface Serial0/0/0 R4(config-if)# ip address 172.22.142.4 255.255.255.0 R4(config-if)# encapsulation frame-relay R4(config-if)# ip ospf message-digest-key 1 md5 CISCO R4(config-if)# ip ospf network point-to-point R4(config-if)# ip ospf hello-interval 60 R4(config-if)# ip ospf 1 area 0 R4(config-if)# ipv6 address 2005:124:124::4/64 R4(config-if)# ipv6 address FE80::4 link-local R4(config-if)# ipv6 ospf network point-to-point R4(config-if)# ipv6 ospf 1 area 124 R4(config-if)# traffic-shape rate 256000 7936 7936 1000 R4(config-if)# frame-relay map ipv6 FE80::2 422 broadcast R4(config-if)# frame-relay map ip 172.22.142.1 422 R4(config-if)# frame-relay map ip 172.22.142.2 422 broadcast R4(config-if)# frame-relay map ipv6 2005:124:124::1 422 R4(config-if)# frame-relay map ipv6 2005:124:124::2 422 broadcast R4(config-if)# no shutdown R4(config-if)#! R4(config- 02:56:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up 02:56:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down 02:56:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to upif)#interface Serial0/0/1 R4(config-if)# shutdown R4(config-if)#! R4(config-if)#interface Serial0/1/0 R4(config-if)# shutdown R4(config-if)#! R4(config-if)#interface Serial0/1/1 R4(config-if)# shutdown R4(config-if)#! R4(config-if)#router eigrp 174 R4(config-router)# redistribute ospf 1 metric 10000 1000 255 1 1500 route-map$te ospf 1 metric 10000 1000 255 1 1500 route-map NotFromR6 R4(config-router)# passive-interface Serial0/0/0 R4(config-router)# network 172.22.0.0 R4(config-router)# distance eigrp 90 90 R4(config-router)# no auto-summary R4(config-router)#! R4(config-router)#router ospf 1 R4(config-router)# router-id 4.4.4.4 R4(config-router)# log-adjacency-changes R4(config-router)# auto-cost reference-bandwidth 1000 % OSPF: Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers. R4(config-router)# area 0 authentication message-digest R4(config-router)# timers throttle spf 6000 6000 6000 R4(config-router)# redistribute eigrp 174 metric-type 1 subnets tag 4 R4(config-router)# distance ospf intra-area 88 inter-area 89 R4(config-router)#! R4(config-router)#router bgp 124 R4(config-router)# no synchronization R4(config-router)# bgp router-id 4.4.4.4 R4(config-router)# bgp log-neighbor-changes R4(config-router)# bgp confederation identifier 4321 R4(config-router)# bgp confederation peers 300 R4(config-router)# neighbor 172.22.32.3 remote-as 300 R4(config-router)# neighbor 172.22.32.3 ebgp-multihop 2 R4(config-router)# neighbor 172.22.142.2 remote-as 124 R4(config-router)# no auto-summary R4(config-router)#! R4(config-router)#ipv6 router ospf 1 R4(config-rtr)# router-id 4.4.4.4 R4(config-rtr)# log-adjacency-changes R4(config-rtr)#! R4(config-rtr)#! R4(config-rtr)#route-map NotFromR6 deny 10 R4(config-route-map)# match tag 6 R4(config-route-map)#! R4(config-route-map)#route-map NotFromR6 permit 20 R4(config-route-map)#line con 0 R4(config-line)# exec-timeout 0 0 R4(config-line)# privilege level 15 R4(config-line)# logging synchronous R4(config-line)#line aux 0 R4(config-line)#line vty 0 4 R4(config-line)# password cisco R4(config-line)# login R4(config-line)#! R4(config-line)#end R4#wr Building configuration... 02:56:39: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.174.1 (FastEthernet0/1) is up: new adjacency 02:56:39: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.174.1 (FastEthernet0/1) is resync: summary configured 02:56:41: %SYS-5-CONFIG_I: Configured from console by console[OK] R4# 02:56:43: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.174.8 (FastEthernet0/1) is up RACK98AS>5 [Resuming connection 5 to r5 ... ]   323 unknown protocol drops --More--   R5(config)#! R5(config)#hostname R5 R5(config)#! R5(config)#ip cef R5(config)#! R5(config)#no ip domain lookup R5(config)#! R5(config)#username R1 password 0 BluesBrothers R5(config)#! R5(config)#interface Loopback0 R5(config-if)# ip address 172.22.85.1 255.255.255.0 R5(config-if)# ip ospf 1 area 1 R5(config-if)#! R5(config-if)#interface Loopback1 R5(config-if)# ip address 144.251.100.201 255.255.255.252 R5(config-if)# ip ospf 1 area 2 R5(config-if)#! R5(config-if)#interface FastEthernet0/0 R5(config-if)# shutdown R5(config-if)#! R5(config-if)#interface FastEthernet0/1 R5(config-if)# no shutdown R5(config-if)#! R5(config-if)#interface FastEthernet0/1.52 R5(config-subif)# encapsulation isl 52 R5(config-subif)# ip address 172.22.52.5 255.255.255.224 % 172.22.52.0 overlaps with FastEthernet0/1 R5(config-subif)# no ip redirects R5(config-subif)# ip ospf 1 area 1 % OSPF will not operate on this interface until IP is configured on it. R5(config-subif)# no snmp trap link-status R5(config-subif)# no shutdown R5(config-subif)#! R5(config-subif)#interface FastEthernet1/0 R5(config-if)# shutdown R5(config-if)#! R5(config-if)#interface Serial1/0 R5(config-if)# no ip address R5(config-if)# encapsulation frame-relay R5(config-if)# frame-relay interface-dlci 521 ppp Virtual-Template1 R5(config-fr-dlci)# no frame-relay inverse-arp R5(config-if)# no shutdown R5(config-if)#! R5(config-if)#interface FastEthernet1/1 R5(config-if)# shutdown R5(config-if)#! R5(config-if)#interface Serial1/1 R5(config-if)# shutdown R5(config-if)#! R5(config-if)#interface Serial1/2 R5(config-if)# shutdown R5(config-if)#! R5(config-if)#interface Serial1/3 R5(config-if)# shutdown R5(config-if)#! R5(config-if)#interface Virtual-Template1 R5(config-if)# bandwidth 64 R5(config-if)# ip address 172.22.51.2 255.255.255.252 R5(config-if)# ip bandwidth-percent eigrp 174 100 R5(config-if)# ip hello-interval eigrp 174 10 R5(config-if)# 02:57:22: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up ip hold-time eigrp 174 30 R5(config-if)# ppp authentication chap R5(config-if)# no shutdown R5(config-if)#! R5(config-if)#router eigrp 174 R5(config-router)# redistribute ospf 1 metric 10000 1000 255 1 1500 R5(config-router)# passive-interface FastEthernet0/1 R5(config-router)# network 172.22.0.0 R5(config-router)# no auto-summary R5(config-router)#! R5(config-router)#router ospf 1 R5(config-router)# router-id 5.5.5.5 R5(config-router)# log-adjacency-changes R5(config-router)# auto-cost reference-bandwidth 1000 % OSPF: Reference bandwidth is changed. Pleas 02:57:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up 02:57:23: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.51.1 (Virtual-Access1) is up: new adjacency 02:57:23: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to upe ensure reference bandwidth is consistent across all routers. R5(config-router)# area 0 authentication message-digest R5(config-router)# area 1 virtual-link 2.2.2.2 message-digest-key 1 md5 CISCO R5(config-router)# redistribute eigrp 174 metric-type 1 subnets tag 5 R5(config-router)#! R5(config-router)#line con 0 R5(config)# exec-timeout 0 0 ^ % Invalid input detected at '^' marker. R5(config)# privilege level 15 ^ % Invalid input detected at '^' marker. R5(config)# logging synchronous Translating "synchronous" ^ % Invalid input detected at '^' marker. R5(config)#line aux 0 R5(config-line)#line vty 0 4 R5(config-line)# password cisco R5(config-line)# login R5(config-line)#line vty 5 15 R5(config-line)# password cisco R5(config-line)# login R5(config-line)#! R5(config-line)#! R5(config-line)#end R5#wr Building configuration... 02:57:24: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 02:57:24: %PARSER-4-INVLDLINE: Invalid line in NV generation: 521 02:57:24: %SYS-5-CONFIG_I: Configured from console by console[OK] R5#conf t Enter configuration commands, one per line. End with CNTL/Z. R5(config)#interface FastEthernet0/1 R5(config-if)# no ip address R5(config-if)# no shutdown R5(config-if)#! R5(config-if)#interface FastEthernet0/1.52 R5(config-subif)# encapsulation isl 52 R5(config-subif)# ip address 172.22.52.5 255.255.255.224 R5(config-subif)# no ip redirects R5(config-subif)# ip ospf 1 area 1 R5(config-subif)# no snmp trap link-status R5(config-subif)# no shutdown R5(config-subif)# 02:58:21: %OSPF-5-ADJCHG: Process 1, Nbr 172.22.82.1 on FastEthernet0/1.52 from LOADING to FULL, Loading Done R5(config-subif)# 02:58:26: %OSPF-5-ADJCHG: Process 1, Nbr 9.9.9.9 on FastEthernet0/1.52 from LOADING to FULL, Loading Done R5(config-subif)#exit R5(config)#! R5(config)#line con 0 R5(config-line)# exec-timeout 0 0 R5(config-line)# privilege level 15 R5(config-line)# logging synchronous R5(config-line)#line aux 0 R5(config-line)#line vty 0 4 R5(config-line)# password cisco R5(config-line)# login R5(config-line)#line vty 5 15 R5(config-line)# password cisco R5(config-line)# login R5(config-line)#! R5(config-line)#! R5(config-line)#end R5#wr Building configuration... 02:58:36: %SYS-5-CONFIG_I: Configured from console by console RACK98AS>6 [Resuming connection 6 to r6 ... ] 02:55:36: %BGP-5-ADJCHANGE: neighbor 172.22.63.3 Up R6(config)# R6(config)#! R6(config)#hostname R6 R6(config)#ip cef R6(config)#no ip domain lookup R6(config)#ip host SW2 172.22.52.9 R6(config)#ip host SW1 172.22.174.8 R6(config)#ip host R7 172.22.87.1 R6(config)#ip host R6 172.22.86.1 R6(config)#ip host R5 172.22.85.1 R6(config)#ip host R4 172.22.84.1 R6(config)#ip host R3 172.22.83.1 R6(config)#ip host R2 172.22.82.1 R6(config)#ip host R1 172.22.81.1 R6(config)#! R6(config)#ipv6 unicast-routing R6(config)#interface Loopback0 R6(config-if)# ip address 172.22.86.1 255.255.255.0 R6(config-if)# ip rip advertise 60 R6(config-if)#! R6(config-if)#interface Loopback1 R6(config-if)# ip address 172.217.59.6 255.255.255.0 secondary R6(config-if)# ip address 150.153.59.6 255.255.255.0 secondary R6(config-if)# ip address 172.153.43.6 255.255.255.0 secondary R6(config-if)# ip address 150.217.43.6 255.255.255.0 secondary R6(config-if)# ip address 150.153.43.6 255.255.255.0 secondary R6(config-if)# ip address 150.217.59.6 255.255.255.0 secondary R6(config-if)# ip address 172.153.59.6 255.255.255.0 secondary R6(config-if)# ip address 200.200.200.1 255.255.255.0 secondary R6(config-if)# ip address 201.201.201.1 255.255.255.0 secondary R6(config-if)# ip address 202.202.202.1 255.255.255.0 secondary R6(config-if)# ip address 172.217.43.6 255.255.255.0 R6(config-if)# ip rip advertise 60 R6(config-if)# ipv6 address 2006:6:6::/128 R6(config-if)# ipv6 rip R6 enable R6(config-if)#! R6(config-if)#interface Tunnel0 R6(config-if)# no ip address R6(config-if)# ipv6 address 2005:26:26::6/64 R6(config-if)# ipv6 rip R6 enable R6(config-if)# keepalive 10 3 R6(config-if)# tunnel source Serial0/0/2 R6(config-if)# tunnel destination 172.22.62.2 R6(config-if)# tunnel mode ipv6ip R6(config-if)# no shutdown R6(config-if)#! R6(config-if)#interface GigabitEthernet0/0 R6(config-if)# shutdown R6(config-if)#! R6(config-if)#interface GigabitEthernet0/1 R6(config-if)# shutdown R6(config-if)#! R6(config-if)#interface Serial0/0/0 R6(config-if)# shutdown R6(config-if)#! R6(config-if)#interface Serial0/0/1 R6(config-if)# shutdown R6(config-if)#! R6(config-if)#interface Serial0/0/2 R6(config-if)# ip address 172.22.62.6 255.255.255.0 R6(config-if)# ip rip advertise 60 R6(config-if)# no fair-queue R6(config-if)# no shutdown R6(config-if)#! R6(config-if)#interface Serial0/0/3 R6(config-if)# ip address 172.22.63.6 255.255.255.0 R6(config-if)# ip rip advertise 60 R6(config-if)# no shutdown R6(config-if)#! R6(config-if)#interface FastEthernet1/0 R6(config-if)# shutdown R6(config-if)#! R6(config-if)#interface FastEthernet1/1 R6(config-if)# shutdown R6(config-if)#! R6(config-if)#router rip R6(config-router)# version 2 R6(config-router)# timers basic 60 240 240 300 R6(config-router)# network 150.153.0.0 R6(config-router)# network 150.217.0.0 R6(config-router)# network 172.16.0.0 R6(config-router)# network 172.21.0.0 R6(config-router)# network 172.22.0.0 R6(config-router)# network 172.23.0.0 R6(config-router)# network 172.153.0.0 R6(config-router)# network 172.217.0.0 R6(config-router)# network 200.200.200.0 R6(config-router)# network 201.201.201.0 R6(config-router)# network 202.202.202.0 R6(config-router)# no auto-summary R6(config-router)#! R6(config-router)#router bgp 600 R6(config-router)# no synchronization R6(config-router)# bgp log-neighbor-changes R6(config-router)# redistribute static route-map filter-statics R6(config-router)# neighbor 172.22.63.3 remote-as 4321 R6(config-router)# neighbor 172.22.63.3 route-map adjust-as out R6(config-router)# no auto-summary R6(config-router)#! R6(config-router)#ip route 200.1.0.0 255.255.0.0 Null0 R6(config)#ip route 206.206.206.0 255.255.255.0 Null0 R6(config)#ip route 206.206.207.0 255.255.255.0 Null0 R6(config)#ip route 207.1.0.0 255.255.255.0 Null0 R6(config)#ip route 207.1.4.0 255.255.255.0 Null0 R6(config)#ip route 207.4.0.0 255.255.255.0 Null0 R6(config)#ip route 208.1.0.0 255.255.255.0 Null0 R6(config) 03:00:58: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up#ip route 208.1.4.0 255.255.255.0 Null0 R6(config)#ip route 208.7.1.0 255.255.255.0 Null0 R6(config)#ip route 208.7.4.0 255.255.255.0 Null0 R6(config)#ip route 215.7.1.0 255.255.255.0 Null0 R6(config)#ip route 215.7.10.0 255.255.255.0 Null0 R6(config)#ip route 215.7.20.0 255.255.255.0 Null0 R6(config)#ip route 215.7.30.0 255.255.255.0 Null0 R6(config)#! R6(config)#access-list 1 permit 208.1.0.0 R6(config)#access-list 2 permit 208.1.4.0 R6(config)#access-list 3 permit 207.4.0.0 R6(config)#access-list 4 permit 207.1.0.0 R6(config)#access-list 5 permit 208.7.4.0 R6(config)#access-list 6 permit 208.7.1.0 R6(config)#access-list 7 permit 207.1.4.0 R6(config)#access-list 8 permit 206.206.206.0 R6(config)#access-list 9 permit 206.206.207.0 R6(config)#access-list 10 permit 208.0.0.0 0.255.255.255 R6(config)#access-list 10 permit 207.0.0.0 0.255.255.255 R6(config)#access-list 10 permit 215.0.0.0 0.255.255.255 R6(config)#access-list 10 permit 200.0.0.0 0.255.255.255 R6(config)#access-list 10 permit 206.0.0.0 0.255.255.255 R6(config)#ipv6 router rip R6 R6(config-rtr)#! R6(config-rtr)#route-map adjust-as permit 10 R6(config-route-map)# match ip address 1 R6(config-route-map)# set as-path prepend 1000 8000 R6(config-route-map)#! R6(config-route-map)#route-map adjust-as permit 15 R6(config-route-map)# match ip address 8 R6(config-route-map)# set as-path prepend 5000 6000 7000 8000 R6(config-route-map)#! R6(config-route-map)#route-map adjust-as permit 18 R6(config-route-map)# match ip address 9 R6(config-route-map)# set as-path prepend 500 1000 1500 R6(config-route-map)#! R6(config-route-map)#route-map adjust-as permit 20 R6(config-route-map)# match ip address 2 R6(config-route-map)# set as-path prepend 4000 1000 8000 R6(config-route-map)#! R6(config-route-map)#route-map adjust-as permit 30 R6(config-route-map)# match ip address 3 R6(config-route-map)# set as-path prepend 4000 7000 R6(config-route-map)#! R6(config-route-map)#route-map adjust-as permit 35 R6(config-route-map)# match ip address 7 R6(config-route-map)# set as-path prepend 4000 1 7000 R6(config-route-map)#! R6(config-route-map)#route-map adjust-as permit 40 R6(config-route-map)# match ip address 4 R6(config-route-map)# set as-path prepend 1000 7000 R6(config-route-map)#! R6(config-route-map)#route-map adjust-as permit 50 R6(config-route-map)# match ip address 5 R6(config-route-map)# set as-path prepend 4000 7000 8000 R6(config-route-map)#! R6(config-route-map)#route-map adjust-as permit 60 R6(config-route-map)# match ip address 6 R6(config-route-map)# set as-path prepend 1000 7000 8000 R6(config-route-map)#! R6(config-route-map)#route-map adjust-as permit 70 R6(config-route-map)# set as-path prepend 900 R6(config-route-map)#! R6(config-route-map)#route-map filter-statics permit 10 R6(config-route-map)# match ip address 10 R6(config-route-map)#! R6(config-route-map)#line con 0 R6(config-line)# exec-timeout 0 0 R6(config-line)# privilege level 15 R6(config-line)# logging synchronous R6(config-line)# stopbits 1 R6(config-line)#line aux 0 R6(config-line)# stopbits 1 R6(config-line)#line vty 0 4 R6(config-line)# password cisco R6(config-line)# login R6(config-line)#! R6(config-line)#end R6#wr Building configuration... [OK] 03:01:03: %SYS-5-CONFIG_I: Configured from console by console R6# RACK98AS>7 [Resuming connection 7 to r7 ... ] *Mar 4 02:25:05.16 R7-FS(config)#! R7-FS(config)#hostname R7-FS R7-FS(config)#! R7-FS(config)#ip cef R7-FS(config)#no ip domain lookup R7-FS(config)#! R7-FS(config)#frame-relay switching R7-FS(config)#! R7-FS(config)#interface Loopback0 R7-FS(config-if)# ip address 172.22.87.1 255.255.255.0 R7-FS(config-if)#! R7-FS(config-if)#interface Loopback99 R7-FS(config-if)# ip address 1.1.1.1 255.255.255.255 R7-FS(config-if)#! R7-FS(config-if)#interface FastEthernet0/0 R7-FS(config-if)# ip address 172.22.174.7 255.255.255.192 R7-FS(config-if)# speed auto R7-FS(config-if)# duplex auto R7-FS(config-if)# no shutdown R7-FS(config-if)#! R7-FS(config-if)#interface FastEthernet0/1 R7-FS(config-if)# shutdown R7-FS(config-if)#! R7-FS(config-if)#interface Serial1/0 R7-FS(config-if)# description To R1 Serial 0/0 R7-FS(config-if)# no ip address R7-FS(config-if)# encapsulation frame-relay R7-FS(config-if)# no fair-queue R7-FS(config-if)# clock rate 128000 R7-FS(config-if)# frame-relay intf-type dce R7-FS(config-if)# frame-relay route 122 interface Serial1/1 221 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 123 interface Serial1/2 321 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 124 interface Serial1/3 421 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 125 interface Serial1/4 521 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 126 interface Serial1/5 621 Can't use same dlci on overlapping circuits R7-FS(config-if)# no shutdown R7-FS(config-if)#! R7-FS(config-if)#interface Serial1/1 R7-FS(config-if)# description To R2 Serial 0/0 R7-FS(config-if)# no ip address R7-FS(config-if)# encapsulation frame-relay R7-FS(config-if)# no fair-queue R7-FS(config-if)# clock rate 128000 R7-FS(config-if)# frame-relay intf-type dce R7-FS(config-if)# frame-relay route 221 interface Serial1/0 122 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 223 interface Serial1/2 322 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 224 interface Serial1/3 422 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 225 interface Serial1/4 522 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 226 interface Serial1/5 622 Can't use same dlci on overlapping circuits R7-FS(config-if)# no shutdown R7-FS(config-if)#! R7-FS(config-if)#interface Serial1/2 R7-FS(config-if)# description To R3 Serial 0/0/0 R7-FS(config-if)# no ip address R7-FS(config-if)# encapsulation frame-relay R7-FS(config-if)# no fair-queue R7-FS(config-if)# clock rate 128000 R7-FS(config-if)# frame-relay intf-type dce R7-FS(config-if)# frame-relay route 321 interface Serial1/0 123 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 322 interface Serial1/1 223 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 324 interface Serial1/3 423 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 325 interface Serial1/4 523 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 326 interface Serial1/5 623 Can't use same dlci on overlapping circuits R7-FS(config-if)# no shutdown R7-FS(config-if)#! R7-FS(config-if)#interface Serial1/3 R7-FS(config-if)# description To R4 Serial 0/0/0 R7-FS(config-if)# no ip address R7-FS(config-if)# encapsulation frame-relay R7-FS(config-if)# no fair-queue R7-FS(config-if)# clock rate 128000 R7-FS(config-if)# frame-relay intf-type dce R7-FS(config-if)# frame-relay route 421 interface Serial1/0 124 Can't use same dlci on over *Mar 4 02:30:46.840: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to uplapping circuits R7-FS(config-if)# frame-relay route 422 interface Serial1/1 224 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 423 interface Serial1/2 324 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 425 interface Serial1/4 524 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 426 interface Serial1/5 624 Can't use same dlci on overlapping circuits R7-FS(config-if)# no shutdown R7-FS(config-if)#! R7-FS(config-if)#interface Serial1/4 R7-FS(config-if)# description To R5 Serial 1/0 R7-FS(config-if)# no ip address R7-FS(config-if)# encapsulation frame-relay R7-FS(config-if)# no fair-queue R7-FS(config-if)# clock rate 128000 R7-FS(config-if)# frame-relay intf-type dce R7-FS(config-if)# frame-relay route 521 interface Serial1/0 125 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 522 interface Serial1/1 225 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 523 interface Serial1/2 325 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 524 interface Serial1/3 425 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 526 interface Serial1/5 625 Can't use same dlci on overlapping circuits R7-FS(config-if)# no shutdown R7-FS(config-if)#! R7-FS(config-if)#interface Serial1/5 R7-FS(config-if)# description To R6 Serial 0/0/0 R7-FS(config-if)# no ip address R7-FS(config-if)# encapsulation frame-relay R7-FS(config-if)# no fair-queue R7-FS(config-if)# clock rate 128000 R7-FS(config-if)# frame-relay intf-type dce R7-FS(config-if)# frame-relay route 621 interface Serial1/0 126 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 622 interface Serial1/1 226 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 623 interface Serial1/2 326 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 624 interface Serial1/3 426 Can't use same dlci on overlapping circuits R7-FS(config-if)# frame-relay route 625 interface Serial1/4 526 Can't use same dlci on overlapping circuits R7-FS(config-if)# no shutdown R7-FS(config-if)#! R7-FS(config-if)#interface Serial1/6 R7-FS(config-if)# shutdown R7-FS(config-if)#! R7-FS(config-if)#interface Serial1/7 R7-FS(config-if)# shutdown R7-FS(config-if)#! R7-FS(config-if)#router eigrp 174 R7-FS(config-router)# network 172.22.0.0 R7-FS(config-router)# no auto-summary R7-FS(config-router)#! R7-FS(config-router)#line con 0 R7-FS(config-line)# exec-timeout 0 0 R7-FS(config-line)# privilege level 15 R7-FS(config-line)# logging synchronous R7-FS(config-line)#line aux 0 R7-FS(config-line)#line vty 0 4 R7-FS(config-line)# password cisco R7-FS(config-line)# login R7-FS(config-line)#! R7-FS(config-line)#end R7-FS#wr Building configuration... *Mar 4 02:30:51.047: %SYS-5-CONFIG_I: Configured from console by console *Mar 4 02:30:54.376: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up[OK] R7-FS# *Mar 4 02:31:17.747: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.174.8 (FastEthernet0/0) is up: new adjacency *Mar 4 02:31:17.755: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.174.4 (FastEthernet0/0) is up: new adjacency *Mar 4 02:31:17.759: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 174: Neighbor 172.22.174.1 (FastEthernet0/0) is up: new adjacency R7-FS#x  RACK98AS>8 [Resuming connection 8 to s1 ... ] 02:50:02: %SYS-5-CON S1#sh mls qos QoS is disabled S1#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   S1#[C  sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Default DSCP Mutation Map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 S1#sh int fa 0/1 qu S1#sh int fa 0/1 que               wrr    wrr S1#sh wrr? % Unrecognized command S1#sh wrr   int fa 0/1 ? accounting Show interface accounting capabilities Show interface capabilities information controller Show interface status, configuration and controller status counters Show interface counters crb Show interface routing/bridging info dampening Show interface dampening info debounce Show interface debounce time info description Show interface description etherchannel Show interface etherchannel information fair-queue Show interface Weighted Fair Queueing (WFQ) info flowcontrol Show interface flowcontrol information irb Show interface routing/bridging info mac-accounting Show interface MAC accounting info mpls-exp Show interface MPLS experimental accounting info mtu Show interface mtu precedence Show interface precedence accounting info private-vlan Show interface private vlan information pruning Show interface trunk VTP pruning information random-detect Show interface Weighted Random Early Detection (WRED) info rate-limit Show interface rate-limit info stats Show interface packets & octets, in & out, by switching path status Show interface line status --More--   summary Show interface summary switchport Show interface switchport information transceiver Show interface transceiver trunk Show interface trunk information vlan Show interface vlan information | Output modifiers S1#sh int fa 0/1            mls qos int fa0/1 qu S1#sh mls qos int fa0/1 queueing FastEthernet0/1 QoS is disabled. Only one queue is used When QoS is enabled, following settings will be applied Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 Cos-queue map: cos-qid 0 - 1 1 - 1 2 - 2 3 - 2 4 - 3 5 - 3 6 - 4 7 - 4 S1# RACK98AS>10 [Resuming connection 10 to s3 ... ] 00:02:13: %LINEPROT S3#sah mls qos map ^ % Invalid input detected at '^' marker. S3#sah mls qos mapsah mls qos map \h mls qos maph mls qos map  Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Cos-dscp map: --More--   cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-outputq-threshold map: d1 :d2 0 1 2 3 4 5 6 7 8 9 ------------------------------------------------------------ 0 : 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 1 : 02-01 02-01 02-01 02-01 02-01 02-01 03-01 03-01 03-01 03-01 2 : 03-01 03-01 03-01 03-01 03-01 03-01 03-01 03-01 03-01 03-01 3 : 03-01 03-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 4 : 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 04-01 04-01 5 : 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 6 : 04-01 04-01 04-01 04-01 Dscp-inputq-threshold map: d1 :d2 0 1 2 3 4 5 6 7 8 9 ------------------------------------------------------------ --More-- RACK98AS>8 [Resuming connection 8 to s1 ... ] S1#sh mls qos int fa0/1 queueing FastEthernet0/1 QoS is disabled. Only one queue is used When QoS is enabled, following settings will be applied Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 Cos-queue map: cos-qid 0 - 1 1 - 1 2 - 2 3 - 2 4 - 3 5 - 3 6 - 4 7 - 4 S1#sh mls qos int fa0/1 queueing a0/1 queueing 0/1 queueing g0/1 queueing i0/1 queueing  GigabitEthernet0/1 QoS is disabled. Only one queue is used When QoS is enabled, following settings will be applied Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 Dscp-threshold map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 01 01 01 01 01 01 01 01 01 01 1 : 01 01 01 01 01 01 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 01 01 01 01 01 01 01 01 4 : 01 01 01 01 01 01 01 01 01 01 5 : 01 01 01 01 01 01 01 01 01 01 6 : 01 01 01 01 Cos-queue map: cos-qid 0 - 1 1 - 1 2 - 2 3 - 2 4 - 3 5 - 3 6 - 4 7 - 4 S1# RACK98AS>10 [Resuming connection 10 to s3 ... ]   0 : 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 --More--   S3#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Cos-dscp map: --More--   cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-outputq-threshold map: d1 :d2 0 1 2 3 4 5 6 7 8 9 ------------------------------------------------------------ 0 : 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 1 : 02-01 02-01 02-01 02-01 02-01 02-01 03-01 03-01 03-01 03-01 2 : 03-01 03-01 03-01 03-01 03-01 03-01 03-01 03-01 03-01 03-01 3 : 03-01 03-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 4 : 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 04-01 04-01 5 : 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 6 : 04-01 04-01 04-01 04-01 Dscp-inputq-threshold map: d1 :d2 0 1 2 3 4 5 6 7 8 9 ------------------------------------------------------------ --More--   0 : 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 --More--   1 : 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 --More--   2 : 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 --More--   3 : 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 --More--   4 : 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 01-01 01-01 --More--   5 : 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 --More--   6 : 01-01 01-01 01-01 01-01 --More--   --More--   Cos-outputq-threshold map: --More--   cos: 0 1 2 3 4 5 6 7 --More--   ------------------------------------ --More--   queue-threshold: 2-1 2-1 3-1 3-1 4-1 1-1 4-1 4-1 --More--   --More--   Cos-inputq-threshold map: --More--   cos: 0 1 2 3 4 5 6 7 --More--   ------------------------------------ --More--   queue-threshold: 1-1 1-1 1-1 1-1 1-1 2-1 1-1 1-1 --More--   --More--   Dscp-dscp mutation map: Default DSCP Mutation Map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 S3#sh mls qos int gi 0/1 qu GigabitEthernet0/1 QoS is disabled. When QoS is enabled, following settings will be applied Egress Priority Queue : disabled Shaped queue weights (absolute) : 25 0 0 0 Shared queue weights : 25 25 25 25 The port bandwidth limit : 100 (Operational Bandwidth:100.0) The port is mapped to qset : 1 S3# RACK98AS>2 [Resuming connection 2 to r2 ... ] 02:49:38: %SYS-5- R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#map R2(config)#map-c R2(config)#map-class l >? % Unrecognized command R2(config)#map-class > ? atm Asynchronous transfer mode dialer Dial on Demand frame-relay Frame Relay R2(config)#map-class fr R2(config)#map-class frame-relay ? WORD Static map class name R2(config)#map-class frame-relay ToR3 R2(config-map-class)#? Static maps class configuration commands: default Set a command to its defaults exit-class Exit from static map class configuration mode frame-relay Configure Map parameters help Description of the interactive help system no Negate a command or set its defaults service-policy class-based service policy R2(config-map-class)#frame-relay ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 7000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R2(config-map-class)#frame-relay cir ? <1-45000000> Applied to both Incoming/Outgoing CIR, Bits per second in Incoming CIR out Outgoing CIR R2(config-map-class)#frame-relay cir 128000 R2(config-map-class)#fram bc R2(config-map-class)#fram bc ? <300-16000000> Applied to both Incoming/Outgoing Bc, Bits in Incoming Bc out Outgoing Bc R2(config-map-class)#fram bc 32000 R2(config-map-class)#fr R2(config-map-class)#frame-relay ad R2(config-map-class)#frame-relay adaptive-shaping ? becn Enable rate adjustment in response to BECN foresight Enable rate adjustment in response to ForeSight messages and BECN interface-congestion Enable rate adjustment depend on interface queue R2(config-map-class)#frame-relay adaptive-shaping BE R2(config-map-class)#frame-relay adaptive-shaping BEcn R2(config-map-class)#fram R2(config-map-class)#frame-relay mi R2(config-map-class)#frame-relay mincir ? <1000-45000000> Applied to both Incoming/Outgoing CIR, Bits per second in Incoming minimum acceptable CIR (Frame-Relay SVC only) out Outgoing minimum acceptable CIR R2(config-map-class)#frame-relay mincir 96000 R2(config-map-class)#exit R2(config)#map R2(config)#map-f cl R2(config)#map-class fr R2(config)#map-class frame-relay ToR4 R2(config-map-class)#fram R2(config-map-class)#frame-relay ci R2(config-map-class)#frame-relay cir 256000 R2(config-map-class)#exit R2(config)#exitframe-relay cir 256000map-class frame-relay ToR4 1 R2(config-map-class)#map-class frame-relay ToR1exit frame-relay cir 256000      312000 R2(config-map-class)#frame-relay cir 312000          be 32000 R2(config-map-class)#int s 0/0.1 R2(config-subif)#do sh run int s 0/0.1 Building configuration... Current configuration : 256 bytes ! interface Serial0/0.1 point-to-point ip address 172.22.32.2 255.255.255.0 ip rip advertise 60 ipv6 address 2005:23:23::2/64 ipv6 address FE80::2 link-local ipv6 ospf network non-broadcast ipv6 ospf 1 area 23 frame-relay interface-dlci 223 end R2(config-subif)#fram clas R2(config-subif)#fram class ToR3 R2(config-subif)#uin   fram class ToR3do sh run int s 0/0.1int s 0/0.1  2 R2(config-subif)#int s 0/0.2fram class ToR3do sh run int s 0/0.1 2 Building configuration... Current configuration : 664 bytes ! interface Serial0/0.2 multipoint ip address 172.22.142.2 255.255.255.0 ip rip advertise 60 ip ospf message-digest-key 1 md5 CISCO ip ospf network point-to-multipoint ip ospf hello-interval 60 ip ospf 1 area 0 ipv6 address 2005:124:124::2/64 ipv6 address FE80::2 link-local ipv6 ospf network point-to-multipoint ipv6 ospf hello-interval 10 ipv6 ospf 1 area 124 frame-relay map ipv6 FE80::4 224 broadcast frame-relay map ip 172.22.142.1 221 broadcast frame-relay map ip 172.22.142.4 224 broadcast frame-relay map ipv6 2005:124:124::1 221 broadcast frame-relay map ipv6 2005:124:124::4 224 broadcast frame-relay map ipv6 FE80::1 221 broadcast end R2(config-subif)#fram inter R2(config-subif)#fram interface-dlci ? <16-1007> Define a switched or locally terminated DLCI R2(config-subif)#fram interface-dlci 224 R2(config-fr-dlci)#? Frame Relay dlci configuration commands: auto Configure Automation class Assign a mapclass to a dlci default Set a command to its defaults exit Exit from FR dlci configuration mode help Description of the interactive help system load-interval Specify interval for load calculation for a dlci no Negate a command or set its defaults vofr Voice over Frame-Relay R2(config-fr-dlci)#l clas R2(config-fr-dlci)#class ToR4 R2(config-fr-dlci)#exit R2(config-subif)#exitclass ToR4fram interface-dlci 224 1 R2(config-fr-dlci)#fram interface-dlci 221exit class ToR4 1 R2(config-fr-dlci)#do sh traffic R2(config-fr-dlci)#int s 0/0 R2(config-if)#fram R2(config-if)#frame-relay traff R2(config-if)#frame-relay traffic-shaping R2(config-if)#frame-relay traffic-shaping int s 0/0 do sh traffic Interface Se0/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 225 56000 875 7000 0 125 875 - 226 56000 875 7000 0 125 875 - Interface Se0/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 223 128000 2000 32000 0 125 2000 BECN Interface Se0/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 224 256000 4000 256000 0 125 4000 - 221 312000 8875 312000 32000 125 4875 - R2(config-if)# RACK98AS>3 [Resuming connection 3 to r3 ... ] _I: Configured from con R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int     do sh ru nin    n iunt   nt s 0/0/0 Building configuration... Current configuration : 470 bytes ! interface Serial0/0/0 ip address 172.22.32.3 255.255.255.0 ip rip advertise 60 encapsulation frame-relay ipv6 address 2005:23:23::3/64 ipv6 address FE80::3 link-local ipv6 ospf neighbor FE80::2 ipv6 ospf 1 area 23 traffic-shape rate 128000 32000 32000 1000 traffic-shape adaptive 96000 frame-relay map ipv6 FE80::2 322 broadcast frame-relay map ip 172.22.32.2 322 broadcast frame-relay map ipv6 2005:23:23::2 322 broadcast no frame-relay inverse-arp end R3(config)#int s 0/0/0 R3(config-if)#traff R3(config-if)#traffic-shape ? adaptive Enable Traffic Shaping adaptation to BECN fecn-adapt Enable Traffic Shaping reflection of FECN as BECN group configure token bucket: group CIR (bps) [Bc (bits) [Be (bits)]] rate configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]] R3(config-if)#traffic-shape rate 128000 ? <0-100000000> bits per interval, sustained R3(config-if)#traffic-shape rate 128000 32000 ? <0-100000000> bits per interval, excess in first interval R3(config-if)#traffic-shape rate 128000 32000 R3(config-if)#traff R3(config-if)#traffic-shape ad R3(config-if)#traffic-shape adaptive ? <1-100000000> Lower Bound Target Bit Rate (bits per second) R3(config-if)#traffic-shape adaptive 96000 R3(config-if)#do sh traff Interface Se0/0/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 128000 8000 32000 32000 250 4000 BECN R3(config-if)# RACK98AS>4 [Resuming connection 4 to r4 ... ] : new adjacency R4# R4#conf t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#do sh run int s 0/09 /0 Building configuration... Current configuration : 598 bytes ! interface Serial0/0/0 ip address 172.22.142.4 255.255.255.0 encapsulation frame-relay ip ospf message-digest-key 1 md5 CISCO ip ospf network point-to-point ip ospf hello-interval 60 ip ospf 1 area 0 ipv6 address 2005:124:124::4/64 ipv6 address FE80::4 link-local ipv6 ospf network point-to-point ipv6 ospf 1 area 124 traffic-shape rate 256000 7936 7936 1000 frame-relay map ipv6 FE80::2 422 broadcast frame-relay map ip 172.22.142.1 422 frame-relay map ip 172.22.142.2 422 broadcast frame-relay map ipv6 2005:124:124::1 422 frame-relay map ipv6 2005:124:124::2 422 broadcast end R4(config)#int s 0/0/0 R4(config-if)#traff R4(config-if)#traffic-shape rate 256000 R4(config-if)#int      RACK98AS>1 [Resuming connection 1 to r1 ... ] 02:47:56: %SYS-5-C R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#do sh run int s 0/0.1 Building configuration... Current configuration : 621 bytes ! interface Serial0/0.1 multipoint bandwidth 128 ip address 172.22.142.1 255.255.255.0 ip ospf message-digest-key 1 md5 CISCO ip ospf network point-to-multipoint ip ospf hello-interval 60 ipv6 address 2005:124:124::1/64 ipv6 address FE80::1 link-local ipv6 nat ipv6 ospf network point-to-point ipv6 ospf 1 area 124 frame-relay map ipv6 FE80::2 122 broadcast frame-relay map ip 172.22.142.1 122 frame-relay map ip 172.22.142.2 122 broadcast frame-relay map ip 172.22.142.4 122 frame-relay map ipv6 2005:124:124::2 122 broadcast frame-relay map ipv6 2005:124:124::4 122 frame-relay interface-dlci 122 end R1(config-subif)#traff R1(config-subif)#traffic-shape rate 312000 ? <0-100000000> bits per interval, sustained R1(config-subif)#traffic-shape rate 312000 ? <0-100000000> bits per interval, sustained R1(config-subif)#traffic-shape rate 312000 39000 >? % Unrecognized command R1(config-subif)#traffic-shape rate 312000 39000 > ? <0-100000000> bits per interval, excess in first interval R1(config-subif)#traffic-shape rate 312000 39000 32000 R1(config-subif)#do sh traff Interface Se0/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 312000 8875 39000 32000 125 4875 - R1(config-subif)# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)# RACK98AS>4 [Resuming connection 4 to r4 ... ] R4(config-if)#do sh int fa 0/1 FastEthernet0/1 is up, line protocol is up Hardware is MV96340 Ethernet, address is 001a.6d2a.cbc9 (bia 001a.6d2a.cbc9) Internet address is 172.22.174.4/26 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 8557 packets input, 746910 bytes Received 8333 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 6604 packets output, 618865 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets --More-- RACK98AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#exit R2(config)#ip acces R2(config)#ip access-list ToVlan174 ^ % Invalid input detected at '^' marker. R2(config)#ip access-list ToVlan174 eToVlan174 xToVlan174  ToVlan174  R2(config-ext-nacl)#per tcp any 172.22.174.0 0.0.0.63 eq www R2(config-ext-nacl)#per tcp any 172.22.174.0 0.0.0.63 eq www   ftp R2(config-ext-nacl)#per tcp any 172.22.174.0 0.0.0.63 eq ftp- R2(config-ext-nacl)#per tcp any 172.22.174.0 0.0.0.63 eq ftp-data R2(config-ext-nacl)#per tcp any 172.22.174.0 0.0.0.63 eq ftp-data  per tcp any 172.22.174.0 0.0.0.63 eq ftp-data             cp any 172.22.174.0 0.0.0.63 icp any 172.22.174.0 0.0.0.63 cmp any 172.22.174.0 0.0.0.63 p any 172.22.174.0 0.0.0.63 echop  R2(config-ext-nacl)#exit R2(config)#route- -map ToVlan174 R2(config-route-map)#match ip add ToVlan174 R2(config-route-map)#set ? as-path Prepend string for a BGP AS-path attribute automatic-tag Automatically compute TAG value clns OSI summary address comm-list set BGP community list (for deletion) community BGP community attribute dampening Set BGP route flap dampening parameters default Set default information extcommunity BGP extended community attribute interface Output interface ip IP specific information ipv6 IPv6 specific information level Where to import route local-preference BGP local preference path attribute metric Metric value for destination routing protocol metric-type Type of metric for destination routing protocol mpls-label Set MPLS label for prefix nlri BGP NLRI type origin BGP origin code tag Tag value for destination routing protocol traffic-index BGP traffic classification number for accounting vrf Define VRF name weight BGP weight for routing table --More--   R2(config-route-map)#set RACK98AS>1 [Resuming connection 1 to r1 ... ] R1(config-subif)#do sh run int s 0/0.1 Building configuration... Current configuration : 665 bytes ! interface Serial0/0.1 multipoint bandwidth 128 ip address 172.22.142.1 255.255.255.0 ip ospf message-digest-key 1 md5 CISCO ip ospf network point-to-multipoint ip ospf hello-interval 60 ipv6 address 2005:124:124::1/64 ipv6 address FE80::1 link-local ipv6 nat ipv6 ospf network point-to-point ipv6 ospf 1 area 124 traffic-shape rate 312000 39000 32000 1000 frame-relay map ipv6 FE80::2 122 broadcast frame-relay map ip 172.22.142.1 122 frame-relay map ip 172.22.142.2 122 broadcast frame-relay map ip 172.22.142.4 122 frame-relay map ipv6 2005:124:124::2 122 broadcast frame-relay map ipv6 2005:124:124::4 122 frame-relay interface-dlci 122 end --More-- RACK98AS>2 [Resuming connection 2 to r2 ... ] % Incomplete command. R2(config-route-map)#set ip ne R2(config-route-map)#set ip next-hop ? A.B.C.D IP address of next hop dynamic application dynamically sets next hop peer-address Use peer address (for BGP only) recursive Recursive next-hop verify-availability Verify if nexthop is reachable R2(config-route-map)#set ip next-hop 172.22.142.1 R2(config-route-map)#int s 0/.2  0.2 R2(config-subif)#int s 0/0.2 1 R2(config-subif)#ip pol R2(config-subif)#ip policy rou R2(config-subif)#ip policy route-map ToVlan174 ? R2(config-subif)#ip policy route-map ToVlan174   R2(config-subif)#int s0/2 R2(config-if)#int s0/2p policy route-map ToVlan174 R2(config-if)#int fa0/0 R2(config-if)#int fa0/0p policy route-map ToVlan174 R2(config-if)#exit R2(config)#ip lo R2(config)#ip local ? policy Enable policy routing pool IP Local address pool lists R2(config)#ip local po R2(config)#ip local po? policy pool R2(config)#ip local pol R2(config)#ip local policy rou R2(config)#ip local policy route-map ToVlan174 R2(config)#^Z R2# 06:16:23: %SYS-5-CONFIG_I: Configured from console by console R2#deb ip pol R2#deb ip policy Policy routing debugging is on R2#ping 172 06:16:31: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected(no match) - normal forwarding R2#ping 172.22.174.4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 172.22.174.4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/36 ms R2# 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4, len 100, policy match 06:16:37: IP: route map ToVlan174, item 10, permit 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4 (Serial0/0.2), len 100, policy routed 06:16:37: IP: local to Serial0/0.2 172.22.142.1 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4, len 100, policy match 06:16:37: IP: route map ToVlan174, item 10, permit 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4 (Serial0/0.2), len 100, policy routed 06:16:37: IP: local to Serial0/0.2 172.22.142.1 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4, len 100, policy match 06:16:37: IP: route map ToVlan174, item 10, permit R2# 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4 (Serial0/0.2), len 100, policy routed 06:16:37: IP: local to Serial0/0.2 172.22.142.1 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4, len 100, policy match 06:16:37: IP: route map ToVlan174, item 10, permit 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4 (Serial0/0.2), len 100, policy routed 06:16:37: IP: local to Serial0/0.2 172.22.142.1 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4, len 100, policy match 06:16:37: IP: route map ToVlan174, item 10, permit 06:16:37: IP: s=172.22.52.2 (local), d=172.22.174.4 (Serial0/0.2), len 100, policy routed 06:16:37: IP: local to Serial0/0.2 172.22.142.1 R2# 06:16:41: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected(no match) - normal forwarding R2# 06:16:45: IP: s=172.22.142.2 (local), d=172.22.142.4, len 59, policy rejected -- normal forwarding 06:16:45: IP: s=172.22.142.2 (local), d=172.22.142.4, len 40, policy rejected -- normal forwarding R2# 06:16:51: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected(no match) - normal forwarding R2# 06:17:01: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected(no match) - normal forwarding R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# 06:17:11: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected(no match) - normal forwarding R2(config)#ip local policy route-map ToVlan174exit ip policy route-map ToVlan174nt fa0/0 p policy route-map ToVlan174nt s0/2 p policy route-map ToVlan174nt s 0/0.1 2set ip next-hop 172.22.142.1 06:17:16: IP: s=172.22.32.2 (local), d=172.22.32.3, len 59, policy rejected -- normal forwarding 06:17:16: IP: s=172.22.32.2 (local), d=172.22.32.3, len 40, policy rejected -- normal forwarding R2(config)#set ip next-hop 172.22.142.1 match ip add ToVlan174route-map ToVlan174 match ip add ToVlan174route-map ToVlan174  20 R2(config-route-map)# 06:17:21: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected(no match) - normal forwarding R2(config-route-map)# 06:17:31: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy match 06:17:31: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected - normal forwarding R2(config-route-map)# 06:17:41: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy match 06:17:41: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected - normal forwarding 06:17:42: IP: s=172.22.142.2 (local), d=172.22.142.4, len 100, policy match 06:17:42: IP: route map ToVlan174, item 20, permit 06:17:42: IP: s=172.22.142.2 (local), d=172.22.142.4 (Serial0/0.2), len 100, policy rejected -- normal forwarding 06:17:42: IP: s=172.22.142.2 (local), d=172.22.142.1, len 100, policy match 06:17:42: IP: route map ToVlan174, item 20, permit 06:17:42: IP: s=172.22.142.2 (local), d=172.22.142.1 (Serial0/0.2), len 100, policy rejected -- normal forwarding R2(config-route-map)# 06:17:42: IP: s=172.22.142.2 (local), d=172.22.142.4, len 100, policy match 06:17:42: IP: route map ToVlan174, item 20, permit 06:17:42: IP: s=172.22.142.2 (local), d=172.22.142.4 (Serial0/0.2), len 100, policy rejected -- normal forwarding 06:17:42: IP: s=172.22.142.2 (local), d=172.22.142.1, len 100, policy match 06:17:42: IP: route map ToVlan174, item 20, permit 06:17:42: IP: s=172.22.142.2 (local), d=172.22.142.1 (Serial0/0.2), len 100, policy rejected -- normal forwarding R2(config-route-map)# 06:17:44: IP: s=172.22.142.2 (local), d=172.22.142.4, len 100, policy match 06:17:44: IP: route map ToVlan174, item 20, permit 06:17:44: IP: s=172.22.142.2 (local), d=172.22.142.4 (Serial0/0.2), len 100, policy rejected -- normal forwarding 06:17:44: IP: s=172.22.142.2 (local), d=172.22.142.1, len 100, policy match 06:17:44: IP: route map ToVlan174, item 20, permit 06:17:44: IP: s=172.22.142.2 (local), d=172.22.142.1 (Serial0/0.2), len 100, policy rejected -- normal forwarding 06:17:45: IP: s=172.22.142.2 (local), d=172.22.142.4, len 59, policy match 06:17:45: IP: route map ToVlan174, item 20, permit 06:17:45: IP: s=172.22.142.2 (local), d=172.22.142.4 R2(config-route-map)#, len 59, policy rejected -- normal forwarding 06:17:45: IP: s=172.22.142.2 (local), d=172.22.142.4, len 40, policy match 06:17:45: IP: route map ToVlan174, item 20, permit 06:17:45: IP: s=172.22.142.2 (local), d=172.22.142.4, len 40, policy rejected -- normal forwarding R2(config-route-map)# 06:17:51: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy match 06:17:51: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected - normal forwarding R2(config-route-map)#do uall 06:18:01: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy match 06:18:01: IP: s=172.22.83.1 (Serial0/0.1), d=172.22.84.1, len 100, FIB policy rejected - normal forwarding R2(config-route-map)#do uall uall ^ % Invalid input detected at '^' marker. R2(config-route-map)#do uall all All possible debugging has been turned off R2(config-route-map)#eix ^ % Invalid input detected at '^' marker. R2(config-route-map)#t exit R2(config)#ip access-list ex ToVlan174B R2(config-ext-nacl)#per ip any 172.22.174.0 0.0.0.63 R2(config-ext-nacl)#exiyt ^ % Invalid input detected at '^' marker. R2(config-ext-nacl)#exiyt  ^ % Invalid input detected at '^' marker. R2(config-ext-nacl)#exiy exiy t R2(config)#clas R2(config)#class-map www R2(config-cmap)#match ip    ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R2(config-cmap)#match acc R2(config-cmap)#match access-group ? <1-2699> Access list index name Named Access List R2(config-cmap)#match access-group name ? WORD Access List name R2(config-cmap)#match access-group name ToVlan174B R2(config-cmap)#match pro R2(config-cmap)#match protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Systems ICA protocol clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP (VJ) cuseeme CU-SeeMe desktop video conference decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching (Direct encapsulation only) dns Domain Name Server lookup edonkey eDonkey --More--   egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Version2 Traffic - BearShare, Shareeza, Morpheus ... gopher Gopher gre Generic Routing Encapsulation h323 H323 Protocol http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) ipsec IP Security Protocol (ESP/AH) ipv6 IPV6 ipx Novell IPX irc Internet Relay Chat kazaa2 Kazaa Version 2 kerberos Kerberos l2tp L2F/L2TP tunnel --More--   R2(config-cmap)#match protocol http R2(config-cmap)#exit R2(config)#clas R2(config)#class-map ftp R2(config-cmap)#class-map ftpexit match protocol httpaccess-group name ToVlan174B R2(config-cmap)#match access-group name ToVlan174B match prot R2(config-cmap)#match protocol ftp R2(config-cmap)#match protocol ftp? ftp R2(config-cmap)#match protocol ftp                  exit R2(config)#do sh ip nbar port ftp port-map ftp tcp 21 R2(config)# R2(config)# R2(config)# R2(config)# R2(config)#ip nbar port ftp tcp 20 R2(config)#ip nbar port ftp tcp 20do sh ip nbar port ftp  port-map ftp tcp 20 R2(config)# R2(config)# R2(config)# R2(config)#do sh ip nbar port ftpip nbar port ftp tcp 20 21 R2(config)#clas R2(config)#class-map echo R2(config-cmap)#match pro R2(config-cmap)#match protocol ec? % Unrecognized command R2(config-cmap)#match protocol ec  icm? icmp R2(config-cmap)#match protocol icm ? R2(config-cmap)#match protocol icm                    exit R2(config)#ip access R2(config)#ip access-list ex R2(config)#ip access-list extended Vlanecho R2(config-ext-nacl)#per icmp any 172.22.0 174.0 0.0.0.63 echo R2(config-ext-nacl)#exit R2(config)#clas R2(config)#class-map      ? class-map R2(config)#class ? % Unrecognized command R2(config)#class   echo ^ % Invalid input detected at '^' marker. R2(config)#class echo      R2(config)#class-map echo R2(config-cmap)#match i acc R2(config-cmap)#match access-group n R2(config-cmap)#match access-group name Vlanecho R2(config-cmap)#exit R2(config)#pol R2(config)#policy-map R2(config)#policy-map ToVlan174 R2(config-pmap)#class R2(config-pmap)#class www R2(config-pmap-c)#pri R2(config-pmap-c)#priority ? <8-2000000> Kilo Bits per second percent % of total bandwidth R2(config-pmap-c)#priority 100 ? <32-2000000> Burst in bytes R2(config-pmap-c)#priority 100   R2(config-pmap-c)#exit R2(config-pmap)#ftp ^ % Invalid input detected at '^' marker. R2(config-pmap)#class ctp   Ftp % class map Ftp not configured R2(config-pmap)#class ftp R2(config-pmap-c)#bas R2(config-pmap-c)#bas  R2(config-pmap-c)#bandwidth ? <8-2000000> Kilo Bits per second percent % of total Bandwidth remaining % of the remaining bandwidth R2(config-pmap-c)#bandwidth 64 R2(config-pmap-c)#exit R2(config-pmap)#class echo R2(config-pmap-c)#pol R2(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate rate Specify police rate R2(config-pmap-c)#police 64000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R2(config-pmap-c)#police 64000 con R2(config-pmap-c)#police 64000 conform-action ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R2(config-pmap-c)#police 64000 conform-action se R2(config-pmap-c)#police 64000 conform-action set-p R2(config-pmap-c)#police 64000 conform-action set-prec-transmit 2 ? exceed-action action when rate is within conform and conform + exceed burst R2(config-pmap-c)#police 64000 conform-action set-prec-transmit 2 ex R2(config-pmap-c)#$0 conform-action set-prec-transmit 2 exceed-action set R2(config-pmap-c)#$0 conform-action set-prec-transmit 2 exceed-action set-p R2(config-pmap-c)#$-prec-transmit 2 exceed-action set-prec-transmit 1 R2(config-pmap-c-police)#exit R2(config-pmap-c)#exit R2(config-pmap)#int s 0/0.1 R2(config-subif)#int s 0/0.1 2exit  R2(config)#exit int s 0/0.1 2 R2(config-subif)#serv R2(config-subif)#service-policy ? input Assign policy-map to the input of an interface output Assign policy-map to the output of an interface R2(config-subif)#service-policy out R2(config-subif)#service-policy output ToVlan174 CBWFQ : Not supported on subinterfaces R2(config-subif)#do sh run int s 0/0.1 2 Building configuration... Current configuration : 754 bytes ! interface Serial0/0.2 multipoint ip address 172.22.142.2 255.255.255.0 ip rip advertise 60 ip ospf message-digest-key 1 md5 CISCO ip ospf network point-to-multipoint ip ospf hello-interval 60 ip ospf 1 area 0 ipv6 address 2005:124:124::2/64 ipv6 address FE80::2 link-local ipv6 ospf network point-to-multipoint ipv6 ospf hello-interval 10 ipv6 ospf 1 area 124 frame-relay map ipv6 FE80::4 224 broadcast frame-relay map ip 172.22.142.1 221 broadcast frame-relay map ip 172.22.142.4 224 broadcast frame-relay map ipv6 2005:124:124::1 221 broadcast frame-relay map ipv6 2005:124:124::4 224 broadcast frame-relay map ipv6 FE80::1 221 broadcast frame-relay interface-dlci 221 class ToR1 --More--   R2(config-subif)#exut ^ % Invalid input detected at '^' marker. R2(config-subif)#exit R2(config)#map R2(config)#map-cl R2(config)#map-class fr R2(config)#map-class frame-relay  R2(config)#map-class frame-relay ToR1 R2(config-map-class)#ser R2(config-map-class)#service-policy ? input input policy output output policy R2(config-map-class)#service-policy out ToVlan174 I/f Serial0/0.2 DLCI 221 class ftp requested bandwidth 64 (kbps), available only 56 (kbps) R2(config-map-class)#do sh ap  map-class sh map-class ^ % Invalid input detected at '^' marker. R2(config-map-class)#do sh map-class      ~    fram map-class sh fram map-class ^ % Invalid input detected at '^' marker. R2(config-map-class)#do sh run | b map-class ToR1 R2(config-map-class)#do sh run | b map-class ToR1      map-class frame-relay ToR3 frame-relay cir 128000 frame-relay bc 32000 frame-relay mincir 96000 frame-relay adaptive-shaping becn ! map-class frame-relay ToR4 frame-relay cir 256000 ! map-class frame-relay ToR1 frame-relay cir 312000 frame-relay be 32000 access-list 100 deny ip host 172.22.62.6 0.1.1.0 255.254.254.255 access-list 100 permit ip any any ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes redistribute rip R2 include-connected ! ipv6 router rip R2 redistribute connected redistribute ospf 1 metric 2 ! --More--   R2(config-map-class)#fram R2(config-map-class)#frame-relay min R2(config-map-class)#frame-relay mincir 312000 R2(config-map-class)#frame-relay mincir 312000do sh run | b map-class  ToR1fram map-class map-class service-policy out ToVlan174 R2(config-map-class)#^Z R2#sh p 06:32:04: %SYS-5-CONFIG_I: Configured from console by console R2#sh pol R2#sh policy-maint   p R2#sh policy-map int s0/.0.   0.2 Serial0/0.2: DLCI 221 - Service-policy output: ToVlan174 Class-map: www (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group name ToVlan174B Match: protocol http Queueing Strict Priority Output Queue: Conversation 40 Bandwidth 100 (kbps) Burst 2500 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group name ToVlan174B Match: protocol ftp Queueing Output Queue: Conversation 41 --More--   Bandwidth 64 (kbps)Max Threshold 64 (packets)