=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2007.03.01 18:57:38 =~=~=~=~=~=~=~=~=~=~=~= R1# R1# R1# R1# R1# R1# RACK13AS>sh sess Conn Host Address Byte Idle Conn Name * 1 r1 1.1.1.1 0 0 r1 2 r2 1.1.1.1 0 01:59 r2 3 r3 1.1.1.1 0 01:59 r3 4 r4 1.1.1.1 0 01:59 r4 5 r5 1.1.1.1 0 01:59 r5 6 r6 1.1.1.1 0 01:59 r6 7 r7 1.1.1.1 4 01:59 r7 RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#conf t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#router bgp 300 S6(config-router)#no auto S6(config-router)#bgp rout S6(config-router)#bgp router-id 6.6.6.6 S6(config-router)#net 9 60.0.0.0 S6(config-router)#net 17.57.101.0 mask 255.255.255.0 S6(config-router)#\net 17.57.101.0 mask 255.255.255.0\ net 17.57.101.0 mask 255.255.255.0.0 mask 255.255.255.0 2.0 mask 255.255.255.0 S6(config-router)#net 17.57.102.0 mask 255.255.255.02.0 mask 255.255.255.0 3.0 mask 255.255.255.0 S6(config-router)#net 17.57.103.0 mask 255.255.255.03.0 mask 255.255.255.0 0.0 mask 255.255.255.0 S6(config-router)#nei 17.57.100.1 remote 300 S6(config-router)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router bgp 300 R1(config-router)#no auto R1(config-router)#bgp rout 1.1.1.1 R1(config-router)#net 19 0.0.0.0 R1(config-router)#net 208.28.1.64 mask 255.255.255.240 R1(config-router)#net 180.40.7.128 mask 255.255.255.224 R1(config-router)#net 180.40.7.128 mask 255.255.255.224 mask 255.255.255.224  mask 255.255.255.224  mask 255.255.255.224 6 mask 255.255.255.2244 mask 255.255.255.224 R1(config-router)#net 208.28.1.0 mask 255.255.255.248 R1(config-router)#nei 17.57.100.2 remote 300 R1(config-router)#neoi  i 208.28.1.65 remote 200 R1(config-router)#nei 180.40.7.129 remote 100 R1(config-router)#nei 180.40.7.129 remote 100 remote 100  remote 100  remote 100 6 remote 1005 remote 100 R1(config-router)#nei 208.28.1.2 *Mar 1 04:39:10.526: %BGP-5-ADJCHANGE: neighbor 17.57.100.2 Up R1(config-router)#nei 208.28.1.2 remote 100 R1(config-router)# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#rouetr     ter bgp 200 S5(config-router)#no auto S5(config-router)#bgp rout 5.5.5.5 S5(config-router)#net 50.0.00 .0 S5(config-router)#net 208.28.1.128 mask 255.255.255.224 S5(config-router)#nei 208.18  28.1.66 remote 300 S5(config-router)#nei 208.28.1.129 remote 100 S5(config-router)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#conif    fi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#route  r bgp 100 R2(config-router)#no auto R2(config-router)#bgp rout 2.2.2.2 R2(config-router)#net 20.0.0.0 R2(config-router)#net 180.40.7.0 mask 255.255.255.224 R2(config-router)#nei 208.28.1.130 remote 200 R2(config-router)#nei 180.40.7.66 remote 300 R2(config-router)#nei 180.40.7.66 remote 300 remote 300  remote 300  remote 300 . remote 3001 remote 3003 remote 3000 remote 300 R2(config-router)#nei 180.40.7.3 remote 100 R2(config-router)# *Mar 1 04:40:28.365: %BGP-5-ADJCHANGE: neighbor 180.40.7.130 Up R2(config-router)# *Mar 1 04:40:31.895: %BGP-5-ADJCHANGE: neighbor 180.40.7.66 Up R2(config-router)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router bgp 100 R3(config-router)#no auto R3(config-router)#bgp rout   R3(config-router)#bgp router-id 3.3.3.3 R3(config-router)#net 30.0.0.0 R3(config-router)#nei 180.40.7.2 remote 100 R3(config-router)#nei 208.28.1.1 remote 300 R3(config-router)#nei 17.80.12 .2 remote 100 R3(config-router)# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router bgp 100 R4(config-router)#no auto R4(config-router)#bgp rout R4(config-router)#bgp router-id 4.4.4.4 R4(config-router)#net 40.0.0.0 R4(config-router)#net 17.80.1.0 mask 255.255.255.0 R4(config-router)#nei 17.80.1.1 remote 100 R4(config-router)# RACK13AS>6 [Resuming connection 6 to r6 ... ] 04:4 S6(config-router)#^Z S6#sh ip 04:45:16: %SYS-5-CONFIG_I: Configured from console by consolebgp sum BGP router identifier 6.6.6.6, local AS number 300 BGP table version is 17, main routing table version 17 14 network entries using 1582 bytes of memory 14 path entries using 728 bytes of memory 5/4 BGP path/bestpath attribute entries using 540 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 2898 total bytes of memory BGP activity 14/0 prefixes, 14/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 17.57.100.1 4 300 13 9 17 0 0 00:04:23 9 S6# S6# S6# S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 4 subnets C 17.57.100.0 is directly connected, FastEthernet0/1 C 17.57.101.0 is directly connected, Loopback0 C 17.57.102.0 is directly connected, Loopback1 C 17.57.103.0 is directly connected, Loopback2 B 50.0.0.0/8 [200/0] via 208.28.1.65, 00:01:35 B 20.0.0.0/8 [200/0] via 180.40.7.65, 00:00:56 B 10.0.0.0/8 [200/0] via 17.57.100.1, 00:04:32 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks B 208.28.1.128/27 [200/0] via 208.28.1.65, 00:01:36 B 208.28.1.64/28 [200/0] via 17.57.100.1, 00:04:33 B 208.28.1.0/29 [200/0] via 17.57.100.1, 00:04:24 180.40.0.0/27 is subnetted, 3 subnets --More--  B 180.40.7.128 [200/0] via 17.57.100.1, 00:04:34 B 180.40.7.0 [200/0] via 180.40.7.65, 00:00:57 B 180.40.7.64 [200/0] via 17.57.100.1, 00:04:34 C 60.0.0.0/8 is directly connected, Loopback99 S6# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Mar R1(config-router)#^Z R1#sh ip bg *Mar 1 04:44:23.895: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip bgp sum BGP router identifier 1.1.1.1, local AS number 300 BGP table version is 21, main routing table version 21 17 network entries using 1717 bytes of memory 30 path entries using 1440 bytes of memory 7 BGP path attribute entries using 420 bytes of memory 4 BGP AS-PATH entries using 96 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 3673 total bytes of memory BGP activity 17/0 prefixes, 30/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 17.57.100.2 4 300 10 16 21 0 0 00:05:15 5 180.40.7.65 4 100 9 11 21 0 0 00:02:40 5 180.40.7.129 4 100 11 12 21 0 0 00:02:43 5 208.28.1.2 4 100 8 9 21 0 0 00:01:26 5 208.28.1.65 4 200 13 12 21 0 0 00:03:26 5 R1# R1# R1# R1# R1# RACK13AS>5 [Resuming connection 5 to r5 ... ] 04:42 S5(config-router)#^Z S5#sh i 04:46:55: %SYS-5-CONFIG_I: Configured from console by console S5#sh ip bgp sum BGP router identifier 5.5.5.5, local AS number 200 BGP table version is 18, main routing table version 18 17 network entries using 1921 bytes of memory 30 path entries using 1560 bytes of memory 8/6 BGP path/bestpath attribute entries using 864 bytes of memory 4 BGP AS-PATH entries using 96 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 4441 total bytes of memory BGP activity 17/0 prefixes, 30/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 208.28.1.66 4 300 13 14 18 0 0 00:04:12 15 208.28.1.129 4 100 11 13 18 0 0 00:03:03 13 S5# S5# S5# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Mar R2(config-router)#do sh ip bgp sum BGP router identifier 2.2.2.2, local AS number 100 BGP table version is 19, main routing table version 19 15 network entries using 1515 bytes of memory 51 path entries using 2448 bytes of memory 9 BGP path attribute entries using 540 bytes of memory 4 BGP AS-PATH entries using 96 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 4599 total bytes of memory BGP activity 15/0 prefixes, 53/2 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 180.40.7.3 4 100 13 11 19 0 0 00:03:05 13 180.40.7.66 4 300 13 11 19 0 0 00:04:01 12 180.40.7.130 4 300 14 13 19 0 0 00:04:05 12 208.28.1.130 4 200 13 11 19 0 0 00:03:39 12 R2(config-router)# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-router)#do  do sh ip bgp sum BGP router identifier 3.3.3.3, local AS number 100 BGP table version is 25, main routing table version 25 17 network entries using 1717 bytes of memory 29 path entries using 1392 bytes of memory 7 BGP path attribute entries using 420 bytes of memory 3 BGP AS-PATH entries using 72 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 3601 total bytes of memory BGP activity 17/0 prefixes, 29/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 17.80.1.2 4 100 7 12 25 0 0 00:02:10 2 180.40.7.2 4 100 11 13 25 0 0 00:03:14 14 208.28.1.1 4 300 10 11 25 0 0 00:02:57 12 R3(config-router)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip bgpo  BGP table version is 20, local router ID is 6.6.6.6 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *>i10.0.0.0 17.57.100.1 0 100 0 i *> 17.57.100.0/24 0.0.0.0 0 32768 i *> 17.57.101.0/24 0.0.0.0 0 32768 i *> 17.57.102.0/24 0.0.0.0 0 32768 i *> 17.57.103.0/24 0.0.0.0 0 32768 i *>i17.80.1.0/24 208.28.1.2 0 100 0 100 i *>i20.0.0.0 180.40.7.65 0 100 0 100 i *>i30.0.0.0 208.28.1.2 0 100 0 100 i *>i40.0.0.0 208.28.1.2 0 100 0 100 i *>i50.0.0.0 208.28.1.65 0 100 0 200 i *> 60.0.0.0 0.0.0.0 0 32768 i *>i180.40.7.0/27 180.40.7.65 0 100 0 100 i *>i180.40.7.64/27 17.57.100.1 0 100 0 i *>i180.40.7.128/27 17.57.100.1 0 100 0 i *>i208.28.1.0/29 17.57.100.1 0 100 0 i *>i208.28.1.64/28 17.57.100.1 0 100 0 i *>i208.28.1.128/27 208.28.1.65 0 100 0 200 i S6#sh ip rout sum IP routing table name is Default-IP-Routing-Table(0) IP routing table maximum-paths is 32 Route Source Networks Subnets Overhead Memory (bytes) connected 1 4 320 760 static 0 0 0 0 bgp 300 5 7 768 1824 External: 0 Internal: 12 Local: 0 internal 3 3516 Total 9 11 1088 6100 S6# S6# S6# S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 5 subnets B 17.80.1.0 [200/0] via 208.28.1.2, 00:04:32 C 17.57.100.0 is directly connected, FastEthernet0/1 C 17.57.101.0 is directly connected, Loopback0 C 17.57.102.0 is directly connected, Loopback1 C 17.57.103.0 is directly connected, Loopback2 B 50.0.0.0/8 [200/0] via 208.28.1.65, 00:06:39 B 20.0.0.0/8 [200/0] via 180.40.7.65, 00:06:00 B 40.0.0.0/8 [200/0] via 208.28.1.2, 00:04:32 B 10.0.0.0/8 [200/0] via 17.57.100.1, 00:09:36 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks B 208.28.1.128/27 [200/0] via 208.28.1.65, 00:06:40 B 208.28.1.64/28 [200/0] via 17.57.100.1, 00:09:37 --More--  B 208.28.1.0/29 [200/0] via 17.57.100.1, 00:09:29 180.40.0.0/27 is subnetted, 3 subnets B 180.40.7.128 [200/0] via 17.57.100.1, 00:09:38 B 180.40.7.0 [200/0] via 180.40.7.65, 00:06:02 B 180.40.7.64 [200/0] via 17.57.100.1, 00:09:38 C 60.0.0.0/8 is directly connected, Loopback99 B 30.0.0.0/8 [200/0] via 208.28.1.2, 00:05:03 S6#sh ip route sum IP routing table name is Default-IP-Routing-Table(0) IP routing table maximum-paths is 32 Route Source Networks Subnets Overhead Memory (bytes) connected 1 4 320 760 static 0 0 0 0 bgp 300 5 7 768 1824 External: 0 Internal: 12 Local: 0 internal 3 3516 Total 9 11 1088 6100 S6# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip bgp     rout sum IP routing table name is Default-IP-Routing-Table(0) Route Source Networks Subnets Overhead Memory (bytes) connected 1 5 384 912 static 0 0 0 0 bgp 300 5 6 704 1672 External: 7 Internal: 4 Local: 0 internal 3 3516 Total 9 11 1088 6100 R1# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip rout sum IP routing table name is Default-IP-Routing-Table(0) IP routing table maximum-paths is 32 Route Source Networks Subnets Overhead Memory (bytes) connected 1 2 192 456 static 0 0 0 0 bgp 200 5 10 960 2280 External: 15 Internal: 0 Local: 0 internal 3 3516 Total 9 12 1152 6252 S5#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 5 subnets B 17.80.1.0 [20/0] via 208.28.1.66, 00:05:55 B 17.57.100.0 [20/0] via 208.28.1.66, 00:08:04 B 17.57.101.0 [20/0] via 208.28.1.66, 00:08:04 B 17.57.102.0 [20/0] via 208.28.1.66, 00:08:04 B 17.57.103.0 [20/0] via 208.28.1.66, 00:08:04 C 50.0.0.0/8 is directly connected, Loopback99 B 20.0.0.0/8 [20/0] via 208.28.1.129, 00:07:29 B 40.0.0.0/8 [20/0] via 208.28.1.66, 00:05:55 B 10.0.0.0/8 [20/0] via 208.28.1.66, 00:08:04 208.28.1.0/24 is variably subnetted, 4 subnets, 3 masks C 208.28.1.128/27 is directly connected, Vlan20 C 208.28.1.64/29 is directly connected, Vlan10 --More--  B 208.28.1.64/28 [20/0] via 208.28.1.66, 00:08:16 B 208.28.1.0/29 [20/0] via 208.28.1.66, 00:08:16 180.40.0.0/27 is subnetted, 3 subnets B 180.40.7.128 [20/0] via 208.28.1.66, 00:08:16 B 180.40.7.0 [20/0] via 208.28.1.129, 00:07:42 B 180.40.7.64 [20/0] via 208.28.1.66, 00:08:16 B 60.0.0.0/8 [20/0] via 208.28.1.66, 00:08:16 B 30.0.0.0/8 [20/0] via 208.28.1.129, 00:06:38 S5#conf t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int vlan 10 S5(config-if)#ip add 208.28.1.65 255.255.255.240 S5(config-if)#^Z S5#conf tsh ip route 04:54:11: %SYS-5-CONFIG_I: Configured from console by console S5#sh ip route sum IP routing table name is Default-IP-Routing-Table(0) IP routing table maximum-paths is 32 Route Source Networks Subnets Overhead Memory (bytes) connected 1 2 192 456 static 0 0 0 0 bgp 200 5 9 896 2128 External: 14 Internal: 0 Local: 0 internal 3 3516 Total 9 11 1088 6100 S5# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#do sh ip rout sum IP routing table name is Default-IP-Routing-Table(0) Route Source Networks Subnets Overhead Memory (bytes) connected 1 4 320 760 static 0 0 0 0 bgp 100 4 6 640 1520 External: 9 Internal: 1 Local: 0 internal 3 3516 Total 8 10 960 5796 R2(config-router)#do sh ip bgp BGP table version is 19, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i10.0.0.0 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i --More--  * 208.28.1.130 0 200 300 i --More--  *> 180.40.7.66 0 300 i --More--  * 180.40.7.130 0 300 i --More--  *> 20.0.0.0 0.0.0.0 0 32768 i --More--  *>i30.0.0.0 180.40.7.3 0 100 0 i --More--  * 50.0.0.0 180.40.7.130 0 300 200 i --More--  * 180.40.7.66 0 300 200 i --More--  *> 208.28.1.130 0 0 200 i --More--   Network Next Hop Metric LocPrf Weight Path * i60.0.0.0 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i *> 180.40.7.0/27 0.0.0.0 0 32768 i r i180.40.7.64/27 208.28.1.1 0 100 0 300 i r 208.28.1.130 0 200 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r i180.40.7.128/27 208.28.1.1 0 100 0 300 i r 208.28.1.130 0 200 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i * i208.28.1.0/29 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * i208.28.1.64/28 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i r 208.28.1.128/27 180.40.7.130 0 300 200 i --More--   Network Next Hop Metric LocPrf Weight Path r 180.40.7.66 0 300 200 i r> 208.28.1.130 0 0 200 i R2(config-router)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 4 subnets B 17.57.100.0 [20/0] via 180.40.7.66, 00:10:46 B 17.57.101.0 [20/0] via 180.40.7.66, 00:10:46 B 17.57.102.0 [20/0] via 180.40.7.66, 00:10:46 B 17.57.103.0 [20/0] via 180.40.7.66, 00:10:46 B 50.0.0.0/8 [20/0] via 208.28.1.130, 00:10:46 C 20.0.0.0/8 is directly connected, Loopback99 B 10.0.0.0/8 [20/0] via 180.40.7.66, 00:10:46 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks C 208.28.1.128/27 is directly connected, FastEthernet0/1 B 208.28.1.64/28 [20/0] via 180.40.7.66, 00:10:47 B 208.28.1.0/29 [20/0] via 180.40.7.66, 00:10:47 180.40.0.0/27 is subnetted, 3 subnets --More--  C 180.40.7.128 is directly connected, Serial1/1 C 180.40.7.0 is directly connected, Serial1/2 C 180.40.7.64 is directly connected, Serial1/0 B 60.0.0.0/8 [20/0] via 180.40.7.66, 00:10:48 B 30.0.0.0/8 [200/0] via 180.40.7.3, 00:09:44 R2(config-router)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#do sh ip bgp sumnei 17.80.1.2 remote 100          rou R3(config-router)#nei 17.80.1.2 route-r R3(config-router)#nei 17.80.1.2 route-reflector-client R3(config-router)# *Mar 1 04:53:21.184: %BGP-5-ADJCHANGE: neighbor 17.80.1.2 Down RR client config change R3(config-router)# *Mar 1 04:53:47.976: %BGP-5-ADJCHANGE: neighbor 17.80.1.2 Up R3(config-router)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 4 subnets B 17.57.100.0 [20/0] via 180.40.7.66, 00:12:35 B 17.57.101.0 [20/0] via 180.40.7.66, 00:12:35 B 17.57.102.0 [20/0] via 180.40.7.66, 00:12:35 B 17.57.103.0 [20/0] via 180.40.7.66, 00:12:35 B 50.0.0.0/8 [20/0] via 208.28.1.130, 00:12:35 C 20.0.0.0/8 is directly connected, Loopback99 B 10.0.0.0/8 [20/0] via 180.40.7.66, 00:12:35 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks C 208.28.1.128/27 is directly connected, FastEthernet0/1 B 208.28.1.64/28 [20/0] via 180.40.7.66, 00:12:36 B 208.28.1.0/29 [20/0] via 180.40.7.66, 00:12:36 180.40.0.0/27 is subnetted, 3 subnets --More--   R2(config-router)#do sh ip routebgp  BGP table version is 19, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i10.0.0.0 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.80.1.0/24 17.80.1.2 0 100 0 i *> 20.0.0.0 0.0.0.0 0 32768 i *>i30.0.0.0 180.40.7.3 0 100 0 i * i40.0.0.0 17.80.1.2 0 100 0 i * 50.0.0.0 180.40.7.130 0 300 200 i * 180.40.7.66 0 300 200 i *> 208.28.1.130 0 0 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i *> 180.40.7.0/27 0.0.0.0 0 32768 i r i180.40.7.64/27 208.28.1.1 0 100 0 300 i r 208.28.1.130 0 200 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r i180.40.7.128/27 208.28.1.1 0 100 0 300 i r 208.28.1.130 0 200 300 i r> 180.40.7.66 0 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path r 180.40.7.130 0 0 300 i * i208.28.1.0/29 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * i208.28.1.64/28 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i r 208.28.1.128/27 180.40.7.130 0 300 200 i r 180.40.7.66 0 300 200 i r> 208.28.1.130 0 0 200 i R2(config-router)#do sh ip bgp BGP table version is 19, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i10.0.0.0 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.80.1.0/24 17.80.1.2 0 100 0 i *> 20.0.0.0 0.0.0.0 0 32768 i *>i30.0.0.0 180.40.7.3 0 100 0 i * i40.0.0.0 17.80.1.2 0 100 0 i * 50.0.0.0 180.40.7.130 0 300 200 i * 180.40.7.66 0 300 200 i *> 208.28.1.130 0 0 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i *> 180.40.7.0/27 0.0.0.0 0 32768 i r i180.40.7.64/27 208.28.1.1 0 100 0 300 i r 208.28.1.130 0 200 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r i180.40.7.128/27 208.28.1.1 0 100 0 300 i r 208.28.1.130 0 200 300 i r> 180.40.7.66 0 0 300 i --More--   R2(config-router)# RACK13AS>4 [Resuming connection 4 to r4 ... ] 04:4 R4(config-router)#ddo    o sh ip bgp BGP table version is 6, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i10.0.0.0 208.28.1.1 0 100 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i *> 17.80.1.0/24 0.0.0.0 0 32768 i * i20.0.0.0 180.40.7.2 0 100 0 i *>i30.0.0.0 17.80.1.1 0 100 0 i *> 40.0.0.0 0.0.0.0 0 32768 i * i50.0.0.0 208.28.1.130 0 100 0 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i * i180.40.7.0/27 180.40.7.2 0 100 0 i * i180.40.7.64/27 208.28.1.1 0 100 0 300 i * i180.40.7.128/27 208.28.1.1 0 100 0 300 i * i208.28.1.0/29 208.28.1.1 0 100 0 300 i * i208.28.1.64/28 208.28.1.1 0 100 0 300 i * i208.28.1.128/27 208.28.1.130 0 100 0 200 i R4(config-router)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#do sh ip bgp BGP table version is 52, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 10.0.0.0 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.100.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.101.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.102.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.103.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i r>i17.80.1.0/24 17.80.1.2 0 100 0 i *>i20.0.0.0 180.40.7.2 0 100 0 i *> 30.0.0.0 0.0.0.0 0 32768 i *>i40.0.0.0 17.80.1.2 0 100 0 i * 50.0.0.0 208.28.1.1 0 300 200 i *>i 208.28.1.130 0 100 0 200 i *> 60.0.0.0 208.28.1.1 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * i 180.40.7.66 0 100 0 300 i r>i180.40.7.0/27 180.40.7.2 0 100 0 i *> 180.40.7.64/27 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *> 180.40.7.128/27 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i r> 208.28.1.0/29 208.28.1.1 0 0 300 i r i 180.40.7.66 0 100 0 300 i *> 208.28.1.64/28 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *> 208.28.1.128/27 208.28.1.1 0 300 200 i * i 208.28.1.130 0 100 0 200 i R3(config-router)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#do sh ip bgproutebgp rout sumbgp sum nei 180.40.7.3 remote 100          nex R2(config-router)#nei 180.40.7.3 next-hop-s R2(config-router)#nei 180.40.7.3 next-hop-self R2(config-router)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#do sh ip bgp BGP table version is 56, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 10.0.0.0 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.100.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.101.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.102.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.103.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i r>i17.80.1.0/24 17.80.1.2 0 100 0 i *>i20.0.0.0 180.40.7.2 0 100 0 i *> 30.0.0.0 0.0.0.0 0 32768 i *>i40.0.0.0 17.80.1.2 0 100 0 i * 50.0.0.0 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i *> 60.0.0.0 208.28.1.1 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * i 180.40.7.2 0 100 0 300 i r>i180.40.7.0/27 180.40.7.2 0 100 0 i *> 180.40.7.64/27 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i *> 180.40.7.128/27 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i r> 208.28.1.0/29 208.28.1.1 0 0 300 i r i 180.40.7.2 0 100 0 300 i *> 208.28.1.64/28 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i * 208.28.1.128/27 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i R3(config-router)# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config-router)#sh ip bgp ^ % Invalid input detected at '^' marker. R4(config-router)#do sh ip bgp BGP table version is 6, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i10.0.0.0 208.28.1.1 0 100 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i *> 17.80.1.0/24 0.0.0.0 0 32768 i * i20.0.0.0 180.40.7.2 0 100 0 i *>i30.0.0.0 17.80.1.1 0 100 0 i *> 40.0.0.0 0.0.0.0 0 32768 i * i50.0.0.0 180.40.7.2 0 100 0 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i * i180.40.7.0/27 180.40.7.2 0 100 0 i * i180.40.7.64/27 208.28.1.1 0 100 0 300 i * i180.40.7.128/27 208.28.1.1 0 100 0 300 i * i208.28.1.0/29 208.28.1.1 0 100 0 300 i * i208.28.1.64/28 208.28.1.1 0 100 0 300 i * i208.28.1.128/27 180.40.7.2 0 100 0 200 i R4(config-router)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#do sh ip bgpnei 17.80.1.2 route-reflector-client                        nex R3(config-router)#nei 17.80.1.2 next-hop-s R3(config-router)#nei 17.80.1.2 next-hop-self R3(config-router)# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config-router)#do sh ip bgp BGP table version is 16, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *>i10.0.0.0 17.80.1.1 0 100 0 300 i *>i17.57.100.0/24 17.80.1.1 0 100 0 300 i *>i17.57.101.0/24 17.80.1.1 0 100 0 300 i *>i17.57.102.0/24 17.80.1.1 0 100 0 300 i *>i17.57.103.0/24 17.80.1.1 0 100 0 300 i *> 17.80.1.0/24 0.0.0.0 0 32768 i * i20.0.0.0 180.40.7.2 0 100 0 i *>i30.0.0.0 17.80.1.1 0 100 0 i *> 40.0.0.0 0.0.0.0 0 32768 i * i50.0.0.0 180.40.7.2 0 100 0 200 i *>i60.0.0.0 17.80.1.1 0 100 0 300 i * i180.40.7.0/27 180.40.7.2 0 100 0 i *>i180.40.7.64/27 17.80.1.1 0 100 0 300 i *>i180.40.7.128/27 17.80.1.1 0 100 0 300 i *>i208.28.1.0/29 17.80.1.1 0 100 0 300 i *>i208.28.1.64/28 17.80.1.1 0 100 0 300 i * i208.28.1.128/27 180.40.7.2 0 100 0 200 i R4(config-router)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#nei 17.80.1.2 next-hop-self nnei 17.80.1.2 next-hop-self onei 17.80.1.2 next-hop-self  nei 17.80.1.2 next-hop-self  R3(config-router)# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config-router)#exit R4(config)#route-map FromR3 R4(config-route-map)#set n ip R4(config-route-map)#set ip  n   p ip n R4(config-route-map)#set ip next-hop ? A.B.C.D IP address of next hop peer-address Use peer address (for BGP only) verify-availability Verify if nexthop is a CDP neighbor R4(config-route-map)#set ip next-hop p R4(config-route-map)#set ip next-hop peer-address ? R4(config-route-map)#set ip next-hop peer-address R4(config-route-map)#router bgp 3 100 R4(config-router)#nei 17.80.1.1 rout R4(config-router)#nei 17.80.1.1 route-m R4(config-router)#nei 17.80.1.1 route-map FromR3 in R4(config-router)#^Z R4#sh ip 05:04:44: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip bgp BGP table version is 36, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i10.0.0.0 208.28.1.1 0 100 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i *> 17.80.1.0/24 0.0.0.0 0 32768 i * i20.0.0.0 180.40.7.2 0 100 0 i *>i30.0.0.0 17.80.1.1 0 100 0 i *> 40.0.0.0 0.0.0.0 0 32768 i * i50.0.0.0 180.40.7.2 0 100 0 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i * i180.40.7.0/27 180.40.7.2 0 100 0 i * i180.40.7.64/27 208.28.1.1 0 100 0 300 i * i180.40.7.128/27 208.28.1.1 0 100 0 300 i * i208.28.1.0/29 208.28.1.1 0 100 0 300 i * i208.28.1.64/28 208.28.1.1 0 100 0 300 i * i208.28.1.128/27 180.40.7.2 0 100 0 200 i R4#  clea ip bgp * in R4#clea ip bgp * in R4#sh ip bgp BGP table version is 50, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *>i10.0.0.0 17.80.1.1 0 100 0 300 i *>i17.57.100.0/24 17.80.1.1 0 100 0 300 i *>i17.57.101.0/24 17.80.1.1 0 100 0 300 i *>i17.57.102.0/24 17.80.1.1 0 100 0 300 i *>i17.57.103.0/24 17.80.1.1 0 100 0 300 i *> 17.80.1.0/24 0.0.0.0 0 32768 i *>i20.0.0.0 17.80.1.1 0 100 0 i *>i30.0.0.0 17.80.1.1 0 100 0 i *> 40.0.0.0 0.0.0.0 0 32768 i *>i50.0.0.0 17.80.1.1 0 100 0 200 i *>i60.0.0.0 17.80.1.1 0 100 0 300 i *>i180.40.7.0/27 17.80.1.1 0 100 0 i *>i180.40.7.64/27 17.80.1.1 0 100 0 300 i *>i180.40.7.128/27 17.80.1.1 0 100 0 300 i *>i208.28.1.0/29 17.80.1.1 0 100 0 300 i *>i208.28.1.64/28 17.80.1.1 0 100 0 300 i *>i208.28.1.128/27 17.80.1.1 0 100 0 200 i R4# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#do sh ip bgp BGP table version is 19, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i10.0.0.0 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i --More--   R2(config-router)#route-map FromR2 3 R2(config-route-map)#set ip ne R2(config-route-map)#set ip next-hop p R2(config-route-map)#set ip next-hop peer-address R2(config-route-map)#router bgp 100 R2(config-router)#nei 17 80;.40    .40.7.3 rout R2(config-router)#nei 180.40.7.3 route-m R2(config-router)#nei 180.40.7.3 route-map FromR3 in R2(config-router)#^Z R2#clea *Mar 1 05:05:37.170: %SYS-5-CONFIG_I: Configured from console by console R2#clea ip bgp * in R2#sh ip bgp BGP table version is 21, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i10.0.0.0 180.40.7.3 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * i17.57.100.0/24 180.40.7.3 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.101.0/24 180.40.7.3 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.102.0/24 180.40.7.3 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * i17.57.103.0/24 180.40.7.3 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i *>i17.80.1.0/24 180.40.7.3 0 100 0 i *> 20.0.0.0 0.0.0.0 0 32768 i *>i30.0.0.0 180.40.7.3 0 100 0 i *>i40.0.0.0 180.40.7.3 0 100 0 i * 50.0.0.0 180.40.7.130 0 300 200 i * 180.40.7.66 0 300 200 i *> 208.28.1.130 0 0 200 i * i60.0.0.0 180.40.7.3 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i *> 180.40.7.0/27 0.0.0.0 0 32768 i r i180.40.7.64/27 180.40.7.3 0 100 0 300 i r 208.28.1.130 0 200 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r i180.40.7.128/27 180.40.7.3 0 100 0 300 i r 208.28.1.130 0 200 300 i r> 180.40.7.66 0 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path r 180.40.7.130 0 0 300 i * i208.28.1.0/29 180.40.7.3 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * i208.28.1.64/28 180.40.7.3 0 100 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i r 208.28.1.128/27 180.40.7.130 0 300 200 i r 180.40.7.66 0 300 200 i r> 208.28.1.130 0 0 200 i R2#sh ip bg    rout sum IP routing table name is Default-IP-Routing-Table(0) Route Source Networks Subnets Overhead Memory (bytes) connected 1 4 320 760 static 0 0 0 0 bgp 100 5 7 768 1824 External: 9 Internal: 3 Local: 0 internal 3 3516 Total 9 11 1088 6100 R2# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip bgp sum BGP router identifier 4.4.4.4, local AS number 100 BGP table version is 50, main routing table version 50 17 network entries using 1717 bytes of memory 17 path entries using 816 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 1 BGP rrinfo entries using 24 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 2845 total bytes of memory BGP activity 27/10 prefixes, 40/23 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 17.80.1.1 4 100 73 34 50 0 0 00:12:24 15 R4#qsh ip bgp sum       rout sum IP routing table name is Default-IP-Routing-Table(0) Route Source Networks Subnets Overhead Memory (bytes) connected 2 1 192 456 static 0 0 0 0 bgp 100 5 10 960 2280 External: 0 Internal: 15 Local: 0 internal 3 3516 Total 10 11 1152 6252 R4#foreach test { ^ % Invalid input detected at '^' marker. R4#17.57.100.1 Trying 17.57.100.1 ... Open 17.57.100.2 17.57.101.1 17.57.102.1 17.57.103.1 208.28.1.65 208.28.1.66 20 Password required, but none set [Connection to 17.57.100.1 closed by foreign host] R4#tclsh R4(tcl)#foreach test { +>(tcl)#17.57.100.1 +>(tcl)#17.57.100.2 +>(tcl)#17.57.101.1 +>(tcl)#17.57.102.1 +>(tcl)#17.57.103.1 +>(tcl)#208.28.1.65 +>(tcl)#208.28.1.66 +>(tcl)#208.28.1.129 +>(tcl)#208.28.1.130 +>(tcl)#180.40.7.65 +>(tcl)#180.40.7.66 +>(tcl)#180.40.7.129 +>(tcl)#180.40.7.130 +>(tcl)#208.28.1.1 +>(tcl)#208.28.1.2 +>(tcl)#180.40.7.2 +>(tcl)#180.40.7.3 +>(tcl)#17.80.1.1 +>(tcl)#17.80.1.2 +>(tcl)#10.1.1.1 +>(tcl)#20.1.1.1 +>(tcl)#30.1.1.1 +>(tcl)#40.1.1.1 +>(tcl)#50.1.1.1 +>(tcl)#60.1.1.1 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 44/46/48 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 72/72/72 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/68/76 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/68/76 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/28/28 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms R4# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#do sh run int s 1/0 Building configuration... Current configuration : 199 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast no frame-relay inverse-arp end R3(config-router)#int s 1/0 R3(config-if)#fram map ip 208.28.1.2 301 R3(config-if)#^Z R3#broadcast *Mar 1 05:08:34.321: %SYS-5-CONFIG_I: Configured from console by console R3#broadcast         tclsh R3(tcl)#foreach test { +>(tcl)#17.57.100.1 +>(tcl)#17.57.100.2 +>(tcl)#17.57.101.1 +>(tcl)#17.57.102.1 +>(tcl)#17.57.103.1 +>(tcl)#208.28.1.65 +>(tcl)#208.28.1.66 +>(tcl)#208.28.1.129 +>(tcl)#208.28.1.130 +>(tcl)#180.40.7.65 +>(tcl)#180.40.7.66 +>(tcl)#180.40.7.129 +>(tcl)#180.40.7.130 +>(tcl)#208.28.1.1 +>(tcl)#208.28.1.2 +>(tcl)#180.40.7.2 +>(tcl)#180.40.7.3 +>(tcl)#17.80.1.1 +>(tcl)#17.80.1.2 +>(tcl)#10.1.1.1 +>(tcl)#20.1.1.1 +>(tcl)#30.1.1.1 +>(tcl)#40.1.1.1 +>(tcl)#50.1.1.1 +>(tcl)#60.1.1.1 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/64/72 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 113/114/116 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 100/100/100 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 61/62/64 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 64/66/68 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 116/132/148 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/33 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/60/64 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/64/68 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 57/58/60 ms R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s 1/0 Building configuration... Current configuration : 183 bytes ! interface Serial1/0 ip address 180.40.7.65 255.255.255.224 encapsulation frame-relay no fair-queue frame-relay map ip 180.40.7.66 201 broadcast no frame-relay inverse-arp end R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#fram    int fam    ram ip             int s 1/0 R2(config-if)#fram map ip 180.40.7.65 201 R2(config-if)#^Z R2# *Mar 1 05:09:23.549: %SYS-5-CONFIG_I: Configured from console by console R2#tclsh R2(tcl)#foreach test { +>(tcl)#17.57.100.1 +>(tcl)#17.57.100.2 +>(tcl)#17.57.101.1 +>(tcl)#17.57.102.1 +>(tcl)#17.57.103.1 +>(tcl)#208.28.1.65 +>(tcl)#208.28.1.66 +>(tcl)#208.28.1.129 +>(tcl)#208.28.1.130 +>(tcl)#180.40.7.65 +>(tcl)#180.40.7.66 +>(tcl)#180.40.7.129 +>(tcl)#180.40.7.130 +>(tcl)#208.28.1.1 +>(tcl)#208.28.1.2 +>(tcl)#180.40.7.2 +>(tcl)#180.40.7.3 +>(tcl)#17.80.1.1 +>(tcl)#17.80.1.2 +>(tcl)#10.1.1.1 +>(tcl)#20.1.1.1 +>(tcl)#30.1.1.1 +>(tcl)#40.1.1.1 +>(tcl)#50.1.1.1 +>(tcl)#60.1.1.1 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/96/137 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/70/84 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 112/116/120 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/62/64 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/34/41 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/62/68 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 112/112/112 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/62/68 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 29/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 29/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 76/78/80 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 57/58/60 ms R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#tclsh R1(tcl)#foreach test { +>(tcl)#17.57.100.1 +>(tcl)#17.57.100.2 +>(tcl)#17.57.101.1 +>(tcl)#17.57.102.1 +>(tcl)#17.57.103.1 +>(tcl)#208.28.1.65 +>(tcl)#208.28.1.66 +>(tcl)#208.28.1.129 +>(tcl)#208.28.1.130 +>(tcl)#180.40.7.65 +>(tcl)#180.40.7.66 +>(tcl)#180.40.7.129 +>(tcl)#180.40.7.130 +>(tcl)#208.28.1.1 +>(tcl)#208.28.1.2 +>(tcl)#180.40.7.2 +>(tcl)#180.40.7.3 +>(tcl)#17.80.1.1 +>(tcl)#17.80.1.2 +>(tcl)#10.1.1.1 +>(tcl)#20.1.1.1 +>(tcl)#30.1.1.1 +>(tcl)#40.1.1.1 +>(tcl)#50.1.1.1 +>(tcl)#60.1.1.1 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 116/126/137 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/40/48 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 80/82/84 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 116/134/153 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 72/78/84 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/68/80 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 57/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms R1# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#macro name testbgp Enter macro commands one per line. End with the character '@'. do ping 17.57.100.1 do ping 17.57.100.2 do ping 17.57.101.1 do ping 17.57.102.1 do ping 17.57.103.1 do ping 208.28.1.65 do ping 208.28.1.66 do ping 208.28.1.129 do ping 208.28.1.130 do ping 180.40.7.65 do ping 180.40.7.66 do ping 180.40.7.129 do ping 180.40.7.130 do ping 208.28.1.1 do ping 208.28.1.2 do ping 180.40.7.2 do ping 180.40.7.3 do ping 17.80.1.1 do ping 17.80.1.2 do ping 10.1.1.1 do ping 20.1.1.1 do ping 30.1.1.1 do ping 40.1.1.1 do ping 50.1.1.1 do ping 60.1.1.1 @ S6(config)# S6(config)#macro global apply testbgp Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/8 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/8 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/43/44 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/72/72 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/12 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms S6(config)#^Z S6# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#macro name testbgp Enter macro commands one per line. End with the character '@'. do ping 17.57.100.1 do ping 17.57.100.2 do ping 17.57.101.1 do ping 17.57.102.1 do ping 17.57.103.1 do ping 208.28.1.65 do ping 208.28.1.66 do ping 208.28.1.129 do ping 208.28.1.130 do ping 180.40.7.65 do ping 180.40.7.66 do ping 180.40.7.129 do ping 180.40.7.130 do ping 208.28.1.1 do ping 208.28.1.2 do ping 180.40.7.2 do ping 180.40.7.3 do ping 17.80.1.1 do ping 17.80.1.2 do ping 10.1.1.1 do ping 20.1.1.1 do ping 30.1.1.1 do ping 40.1.1.1 do ping 50.1.1.1 do ping 60.1.1.1 @ S5(config)# S5(config)#macro global apply testbgp Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/64 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/43/44 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/31/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/9/36 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/39/72 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5(config)# S5(config)#^Z S5# 05:13:39: %SYS-5-CONFIG_I: Configured from console by console S5# S5# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | v b rouetr   ter router bgp 300 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes network 10.0.0.0 network 180.40.7.64 mask 255.255.255.224 network 180.40.7.128 mask 255.255.255.224 network 208.28.1.0 mask 255.255.255.248 network 208.28.1.64 mask 255.255.255.240 neighbor 17.57.100.2 remote-as 300 neighbor 180.40.7.65 remote-as 100 neighbor 180.40.7.129 remote-as 100 neighbor 208.28.1.2 remote-as 100 neighbor 208.28.1.65 remote-as 200 no auto-summary ! no ip http server ip classless ! ! ! ! ! --More-- RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run \ b   | b router router bgp 100 no synchronization bgp router-id 2.2.2.2 bgp log-neighbor-changes network 20.0.0.0 network 180.40.7.0 mask 255.255.255.224 neighbor 180.40.7.3 remote-as 100 neighbor 180.40.7.3 next-hop-self neighbor 180.40.7.3 route-map FromR3 in neighbor 180.40.7.66 remote-as 300 neighbor 180.40.7.130 remote-as 300 neighbor 208.28.1.130 remote-as 200 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! route-map FromR3 permit 10 set ip next-hop peer-address ! --More-- RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes network 30.0.0.0 neighbor 17.80.1.2 remote-as 100 neighbor 17.80.1.2 route-reflector-client neighbor 180.40.7.2 remote-as 100 neighbor 208.28.1.1 remote-as 300 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! dial-peer cor custom --More-- RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#shg    ry un | b bgp router bgp 100 no synchronization bgp router-id 4.4.4.4 bgp log-neighbor-changes network 17.80.1.0 mask 255.255.255.0 network 40.0.0.0 neighbor 17.80.1.1 remote-as 100 neighbor 17.80.1.1 route-map FromR3 in no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! route-map FromR3 permit 10 set ip next-hop peer-address ! ! ! dial-peer cor custom ! --More-- RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | b router router bgp 200 no synchronization bgp router-id 5.5.5.5 bgp log-neighbor-changes network 50.0.0.0 network 208.28.1.128 mask 255.255.255.224 neighbor 208.28.1.66 remote-as 300 neighbor 208.28.1.129 remote-as 100 no auto-summary ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 --More-- RACK13AS>6 [Resuming connection 6 to r6 ... ] 05: S6#sh run | b router router bgp 300 no synchronization bgp router-id 6.6.6.6 bgp log-neighbor-changes network 17.57.100.0 mask 255.255.255.0 network 17.57.101.0 mask 255.255.255.0 network 17.57.102.0 mask 255.255.255.0 network 17.57.103.0 mask 255.255.255.0 network 60.0.0.0 neighbor 17.57.100.1 remote-as 300 no auto-summary ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 --More-- RACK13AS>7 [Resuming connection 7 to r7 ... ] Router>en Router#confi t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R7 R7(config)#! R7(config)#logging queue-limit 100 R7(config)#! R7(config)#ip subnet-zero R7(config)#! R7(config)#! R7(config)#no ip domain lookup R7(config)#! R7(config)#ip audit notify log R7(config)#ip audit po max-events 100 R7(config)#mpls ldp logging neighbor-changes R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#no voice hpi capture buffer R7(config)#no voice hpi capture destination R7(config)#! R7(config)#! R7(config)#mta receive maximum-recipients 0 R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#interface Loopback107 R7(config-if)# description Routes for AS107 R7(config-if)# ip address 192.168.11.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.12.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.13.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.14.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.10.1 255.255.255.0 R7(config-if)#! R7(config-if)#interface Loopback207 R7(config-if)# description Routes for AS207 R7(config-if)# ip address 192.168.21.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.22.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.23.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.24.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.20.1 255.255.255.0 R7(config-if)#! R7(config-if)#interface Loopback307 R7(config-if)# description Routes for AS307 R7(config-if)# ip address 192.168.31.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.32.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.33.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.34.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.30.1 255.255.255.0 R7(config-if)#! R7(config-if)#no ip http server R7(config)#no ip http secure-server R7(config)#ip classless R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#call rsvp-sync R7(config)#! R7(config)#! R7(config)#mgcp profile default R7(config-mgcp-profile)#! R7(config-mgcp-profile)#! R7(config-mgcp-profile)#! R7(config-mgcp-profile)#dial-peer cor custom R7(config-dp-cor)#! R7(config-dp-cor)#! R7(config-dp-cor)#! R7(config-dp-cor)#! R7(config-dp-cor)#! R7(config-dp-cor)#line con 0 R7(config-line)# exec-timeout 0 0 R7(config-line)# logging synchronous R7(config-line)#line aux 0 R7(config-line)#line vty 0 4 R7(config-line)# privilege level 15 R7(config-line)# no login R7(config-line)#! R7(config-line)#! R7(config-line)#end    R7(config-line)# R7(config-line)# R7(config-line)# R7(config-line)# RACK13AS>5 [Resuming connection 5 to r5 ... ]   login --More--   S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/5 S5(config-if)#sw S5(config-if)#switchport tr S5(config-if)#switchport trunk e S5(config-if)#switchport trunk encapsulation do S5(config-if)#switchport trunk encapsulation dot1q S5(config-if)#se w S5(config-if)#switchport mo S5(config-if)#switchport mode tr S5(config-if)#switchport mode trunk S5(config-if)#switchport mode trunk do sh run int s fa 0/7 5 ^ % Invalid input detected at '^' marker. S5(config-if)#switchport mode trunk do sh run int fa 0/5 do sh run int fa 0/5 Building configuration... Current configuration : 94 bytes ! interface FastEthernet0/5 switchport trunk encapsulation dot1q switchport mode trunk end S5(config-if)#default fa 0/5 ^ % Invalid input detected at '^' marker. S5(config-if)#default fa 0/5ifa 0/5nfa 0/5tfa 0/5 fa 0/5 Interface FastEthernet0/5 set to default configuration S5(config)#int fa 0/7 S5(config-if)#int fa 0/7default int fa 0/5fa 0/5 o sh run int fa 0/5switchport mode trunk do sh run int fa 0/5 trunk encapsulation dot1q S5(config-if)#switchport trunk encapsulation dot1q int fa 0/7 default int fa 0/5fa 0/5 o sh run int fa 0/5switchport mode trunk do sh run int fa 0/5  S5(config-if)#do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/2, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Gi0/1, Gi0/2 10 VLAN0010 active Fa0/1 16 VLAN0016 active 20 VLAN0020 active 30 VLAN0030 active Fa0/3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 16 enet 100016 1500 - - - - - 0 0 --More--   S5(config-if)#exit S5(config)#vlan 76 S5(config-vlan)#name R7toS6 S5(config-vlan)#exit S5(config)#vlan   75 S5(config-vlan)#name R7to  S5 S5(config-vlan)#exit S5(config)#int vlan 75 S5(config-if)#ip A   05:22:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan75, changed state to down S5(config-if)#ip add 75. .75.75.5 255.255.255.0 S5(config-if)#router bgp 05:22:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan75, changed state to up S5(config-if)#router bgp 200 S5(config-router)#net 75.75.75.7 0 mask 255.25..  5.255.0 S5(config-router)#^Z S5# RACK13AS>6 [Resuming connection 6 to r6 ... ]  line vty 0 4 --More--   S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int vlan 76 S6(config-if)#ip add 7 05:23:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan76, changed state to up6.76.76.6 255.255.255.0 S6(config-if)#router bgp 300 S6(config-router)#net 76.76.76.0 mask 255.255.255.90  0 S6(config-router)#nei 76.76.76.7 remote 307 S6(config-router)# RACK13AS>5 [Resuming connection 5 to r5 ... ] 05:22: S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#routyer     er bgp 200 S5(config-router)#nei 75.75.75.7 remote 207 S5(config-router)#^Z S5# RACK13AS>4 [Resuming connection 4 to r4 ... ]  ! --More--   R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router bgp 100 R4(config-router)#nei 17.80.1  .7 remote 107 R4(config-router)#^Z R4# 05:24:10: %SYS-5-CONFIG_I: Configured from console by console R4# RACK13AS>3 [Resuming connection 3 to r3 ... ]  ! --More--   R3#cio  onfi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rouetr     ter bgp 100 R3(config-router)#nei 17.80.21.   1.7 remote 107 R3(config-router)#^Z R3# *Mar 1 05:21:59.404: %SYS-5-CONFIG_I: Configured from console by console R3# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7(config-line)#exit R7(config)#ip vrf AS107 R7(config-vrf)#rd 107:1 R7(config-vrf)#rout R7(config-vrf)#route-target 107:1 R7(config-vrf)#exit R7(config)#exitroute-target 107:1d 107:1 ip vrf AS10707 207 R7(config-vrf)#ip vrf AS207exit route-target 107:1107:1 207:1 R7(config-vrf)#route-target 207:1ip vrf AS207 exit route-target 107:1d 107:1 07:1 207:1 R7(config-vrf)#rd 207:1oute-target 207:1ip vrf AS207 07 307 R7(config-vrf)#ip vrf AS307rd 207:1 oute-target 207:1ip vrf AS207 route-target 207:1d 207:1 07:1 307:1 R7(config-vrf)#rd 307:1ip vrf AS307rd 207:1 ip vrf AS307rd 207:1 oute-target 207:1ip vrf AS207 route-target 207:107:1 307:1 R7(config-vrf)#exit R7(config)#int lo 0 107 R7(config-if)#do sh run int lo 107 Building configuration... Current configuration : 294 bytes ! interface Loopback107 description Routes for AS107 ip address 192.168.11.1 255.255.255.0 secondary ip address 192.168.12.1 255.255.255.0 secondary ip address 192.168.13.1 255.255.255.0 secondary ip address 192.168.14.1 255.255.255.0 secondary ip address 192.168.10.1 255.255.255.0 end R7(config-if)#ip vrf fou R7(config-if)#ip vrf fou  R7(config-if)#ip vrf forwarding AS107 % Interface Loopback107 IP address 192.168.10.1 removed due to enabling VRF AS107 R7(config-if)#ip vrf forwarding AS107do sh run int lo 107  Building configuration... Current configuration : 99 bytes ! interface Loopback107 description Routes for AS107 ip vrf forwarding AS107 no ip address end R7(config-if)# ip address 192.168.11.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.12.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.13.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.14.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.10.1 255.255.255.0 R7(config-if)#exit R7(config)#int lo 207 R7(config-if)#int lo 207exit  ip address 192.168.10.1 255.255.255.04.1 255.255.255.0 secondary3.1 255.255.255.0 secondary2.1 255.255.255.0 secondary1.1 255.255.255.0 secondarydo sh run int lo 107 07 207 Building configuration... Current configuration : 294 bytes ! interface Loopback207 description Routes for AS207 ip address 192.168.21.1 255.255.255.0 secondary ip address 192.168.22.1 255.255.255.0 secondary ip address 192.168.23.1 255.255.255.0 secondary ip address 192.168.24.1 255.255.255.0 secondary ip address 192.168.20.1 255.255.255.0 end R7(config-if)#do sh run int lo 207int lo 207 exit  ip address 192.168.10.1 255.255.255.04.1 255.255.255.0 secondary3.1 255.255.255.0 secondary2.1 255.255.255.0 secondary1.1 255.255.255.0 secondarydo sh run int lo 107 ip vrf forwarding AS107107 207 % Interface Loopback207 IP address 192.168.20.1 removed due to enabling VRF AS207 R7(config-if)# ip address 192.168.21.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.22.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.23.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.24.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.20.1 255.255.255.0 R7(config-if)#int lo 307 R7(config-if)#do sh ip  run int lo 1 307 Building configuration... Current configuration : 294 bytes ! interface Loopback307 description Routes for AS307 ip address 192.168.31.1 255.255.255.0 secondary ip address 192.168.32.1 255.255.255.0 secondary ip address 192.168.33.1 255.255.255.0 secondary ip address 192.168.34.1 255.255.255.0 secondary ip address 192.168.30.1 255.255.255.0 end R7(config-if)#do sh run int lo 307int lo 307  ip address 192.168.20.1 255.255.255.04.1 255.255.255.0 secondary3.1 255.255.255.0 secondary2.1 255.255.255.0 secondary1.1 255.255.255.0 secondaryip vrf forwarding AS207 do sh run int lo 207 ip vrf forwarding AS20707 307 % Interface Loopback307 IP address 192.168.30.1 removed due to enabling VRF AS307 R7(config-if)# ip address 192.168.31.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.32.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.33.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.34.1 255.255.255.0 secondary R7(config-if)# ip address 192.168.30.1 255.255.255.0 R7(config-if)# R7(config-if)# R7(config-if)#int fa0/0.30 R7(config-subif)#en R7(config-subif)#encapsulation dot 30 R7(config-subif)#ip add 17.80.1.7 255                    ip vrf for R7(config-subif)#ip vrf forwarding AS107 R7(config-subif)#ip add 17.80.1.7 255.255.255.0 R7(config-subif)#int fa 0/0.75 R7(config-subif)#en R7(config-subif)#encapsulation do R7(config-subif)#encapsulation dot1Q 75 R7(config-subif)#encapsulation dot1Q 75int fa 0/0.75 p add 17.80.1.7 255.255.255.0vrf forwarding AS107 07 207 R7(config-subif)#ip ad 75.75.75.7 255.255.255.0 R7(config-subif)#int fa 0/0/7676 .76 R7(config-subif)#en do 76 R7(config-subif)#ip vrf fo AS307 R7(config-subif)#ip add 776  6.76.76.7 255.255.255.0 R7(config-subif)#int fa 0/0 R7(config-if)#no shut R7(config-if)# *Mar 1 05:27:56.193: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 05:27:57.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R7(config-if)#do p 76.76.76.6 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 76.76.76.6, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7(config-if)#do p 76.76.76.6 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 76.76.76.6, timeout is 2 seconds: .... RACK13AS>5 [Resuming connection 5 to r5 ... ] 05: S5#sh span VLAN0001 Spanning tree enabled protocol ieee Root ID Priority 32769 Address 0013.80e2.0000 Cost 19 Port 24 (FastEthernet0/24) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32769 (priority 32768 sys-id-ext 1) Address 0013.80e2.1c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 15 Interface Role Sts Cost Prio.Nbr Type ---------------- ---- --- --------- -------- -------------------------------- Fa0/7 Desg FWD 19 128.7 P2p Fa0/8 Desg FWD 100 128.8 Shr Fa0/23 Desg FWD 19 128.23 P2p Fa0/24 Root FWD 19 128.24 P2p --More--   S5#sh p span int fa 0/7 Vlan Role Sts Cost Prio.Nbr Type ---------------- ---- --- --------- -------- -------------------------------- VLAN0001 Desg FWD 19 128.7 P2p VLAN0010 Desg FWD 19 128.7 P2p VLAN0016 Desg FWD 19 128.7 P2p VLAN0020 Desg FWD 19 128.7 P2p VLAN0030 Desg FWD 19 128.7 P2p VLAN0075 Desg FWD 19 128.7 P2p VLAN0076 Desg FWD 19 128.7 P2p S5# RACK13AS>7 [Resuming connection 7 to r7 ... ] . S R7(config-if)#do p 76.76.76.6 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 76.76.76.6, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7(config-if)#do p 75.75.75.5 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 75.75.75.5, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7(config-if)# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/7 on 802.1q trunking 1 Fa0/24 desirable n-802.1q trunking 1 Port Vlans allowed on trunk Fa0/7 1-4094 Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/7 1,10,16,20,30,75-76 Fa0/24 1,10,16,20,30,75-76 Port Vlans in spanning tree forwarding state and not pruned Fa0/7 1,10,16,20,30,75-76 Fa0/24 1,10,16,20,30,75-76 S5# RACK13AS> [Resuming connection 5 to r5 ... ] S5#sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES manual administratively down down Vlan10 208.28.1.65 YES manual up up Vlan20 208.28.1.130 YES manual up up Vlan75 75.75.75.5 YES manual up up FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset up up FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down --More--   S5#^x7 % Unknown command or computer name, or unable to find computer address S5# S5# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#do sh int fa 0/0 FastEthernet0/0 is up, line protocol is up Hardware is AmdFE, address is 0012.43ac.6f60 (bia 0012.43ac.6f60) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:04, output 00:00:07, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 27 packets input, 4173 bytes Received 25 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 34 packets output, 7729 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred --More--   R7(config-if)#do sh int fa 0/0.30 FastEthernet0/0.30 is up, line protocol is up Hardware is AmdFE, address is 0012.43ac.6f60 (bia 0012.43ac.6f60) Internet address is 17.80.1.7/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation 802.1Q Virtual LAN, Vlan ID 30. ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters never R7(config-if)#do sh int fa 0/0.30  75 FastEthernet0/0.75 is up, line protocol is up Hardware is AmdFE, address is 0012.43ac.6f60 (bia 0012.43ac.6f60) Internet address is 75.75.75.7/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation 802.1Q Virtual LAN, Vlan ID 75. ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters never R7(config-if)#do sh int fa 0/0.75 6 FastEthernet0/0.76 is up, line protocol is up Hardware is AmdFE, address is 0012.43ac.6f60 (bia 0012.43ac.6f60) Internet address is 76.76.76.7/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation 802.1Q Virtual LAN, Vlan ID 76. ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters never R7(config-if)#do sh int fa 0/0.76530 p 75.75.75.5  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 75.75.75.5, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7(config-if)# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#ping 75.75.. 75.7 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 75.75.75.7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#sh int vlan 75 Vlan75 is up, line protocol is up Hardware is EtherSVI, address is 0013.80e2.1c80 (bia 0013.80e2.1c80) Internet address is 75.75.75.5/24 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:08, output 00:00:08, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 2 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 7 packets input, 718 bytes, 0 no buffer Received 0 broadcasts (0 IP multicast) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 19 packets output, 1410 bytes, 0 underruns 0 output errors, 0 interface resets 0 output buffer failures, 0 output buffers swapped out S5#q  RACK13AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#do p 75.75.75.5 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 75.75.75.5, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7(config-if)#do sh int fa 0/0.75 FastEthernet0/0.75 is up, line protocol is up Hardware is AmdFE, address is 0012.43ac.6f60 (bia 0012.43ac.6f60) Internet address is 75.75.75.7/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation 802.1Q Virtual LAN, Vlan ID 75. ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters never R7(config-if)# R7(config-if)# R7(config-if)# R7(config-if)#do sh ip arp R7(config-if)#do sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater Device ID Local Intrfce Holdtme Capability Platform Port ID S5 Fas 0/0 138 R S I WS-C3550-2Fas 0/7 R7(config-if)# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.75.75.7 2 0012.43ac.6f60 ARPA Vlan75 Internet 208.28.1.129 52 0013.60f0.fd41 ARPA Vlan20 Internet 75.75.75.5 - 0013.80e2.1c80 ARPA Vlan75 Internet 208.28.1.130 - 0013.80e2.1c80 ARPA Vlan20 Internet 208.28.1.65 - 0013.80e2.1c80 ARPA Vlan10 Internet 208.28.1.66 40 000a.8af0.d980 ARPA Vlan10 S5#6 75.75.75.7 Trying 75.75.75.7 ... Open R7#q [Connection to 75.75.75.7 closed by foreign host] S5# S5# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#~do sh cdp neiip arp nt fa 0/0.75p 75.75.75.5  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 75.75.75.5, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7(config-if)#^Z R7# *Mar 1 05:32:56.261: %SYS-5-CONFIG_I: Configured from console by console R7#sh     RACK13AS>6 [Resuming connection 6 to r6 ... ] S6(config-router)#do p 76.76.76.78 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 76.76.76.78, timeout is 2 seconds: .. Success rate is 0 percent (0/2) S6(config-router)# S6(config-router)#do p 76.76.76.78  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 76.76.76.7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S6(config-router)# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip rout Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set R7# R7# R7# R7# R7#ping ip vrf R7#ping ip vrf? WORD R7#ping ip vrf   ? Translating "vrf" R7#ping ip vrf       p ? WORD Ping destination address or hostname R7#ping ip      ? WORD Ping destination address or hostname appletalk Appletalk echo clns CLNS echo decnet DECnet echo ip IP echo ipv6 IPv6 echo ipx Novell/IPX echo srb srb echo tag Tag encapsulated IP echo vrf Select VPN routing instance R7#ping vrf ? WORD VPN Routing/Forwarding instance name R7#ping vrf AS207 ? WORD Ping destination address or hostname appletalk Appletalk echo clns CLNS echo decnet DECnet echo ip IP echo ipv6 IPv6 echo ipx Novell/IPX echo srb srb echo tag Tag encapsulated IP echo R7#ping vrf AS207 75.75.75.7 5 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 75.75.75.5, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R7#ping vrf AS207 75.75.75.55 ping vrf AS207 75.75.75.5              307 76.76.76.6 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 76.76.76.6, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R7#ping vrf AS307 76.76.76.6              107 17.80.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R7#ping vrf AS107 17.80.1.1 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#router bgp 107 R7(config-router)#no auto R7(config-router)#bgp router R7(config-router)#bgp router-id 7.7.7.7 R7(config-router)#add R7(config-router)#address-family ? ipv4 Address family ipv6 Address family nsap Address family vpnv4 Address family R7(config-router)#address-family v R7(config-router)#address-family vpnv4 ? unicast Address Family Modifier R7(config-router)#address-family vpnv4       ip R7(config-router)#address-family ipvv4 ? % Unrecognized command R7(config-router)#address-family ipvv4    4 ? multicast Address Family modifier unicast Address Family modifier vrf Specify parameters for a VPN Routing/Forwarding instance R7(config-router)#address-family ipv4 vrf ? WORD VPN Routing/Forwarding instance name R7(config-router)#address-family ipv4 vrf as  AS107 R7(config-router-af)#et  net 192.168.10.0 R7(config-router-af)#net 192.168.10.0 .0 1.0  R7(config-router-af)#net 192.168.11.0 .0 2.0  R7(config-router-af)#net 192.168.12.0 .0 3.0  R7(config-router-af)#net 192.168.13.0 3.0 4.0  R7(config-router-af)#nei 17.80.1.1 remote 100 R7(config-router-af)#nei 17.80.1.1 remote 100 remote 100 2 remote 100 R7(config-router-af)#nei 17.80.1.2 remote 1001 remote 100t 192.168.14.0 3.0 2.0 1.0 0.0 address-family ipv4 vrf AS10707 207 R7(config-router-af)#address-family ipv4 vrf AS207nei 17.80.1.2 remote 100 1 remote 100t 192.168.14.0 3.0 2.0 1.0 0.0 0.0 20.0  R7(config-router-af)#net 192.168.20.0 0.0 1.0  R7(config-router-af)#net 192.168.21.0 1.0 1.0 2.0 2.0  R7(config-router-af)#net 192.168.22.0 2.0 3.0  R7(config-router-af)#net 192.168.23.0 .0 4.0  R7(config-router-af)#nei 75.75.75.5 remote 200 R7(config-router-af)# *Mar 1 05:37:06.816: %BGP-5-ADJCHANGE: neighbor 17.80.1.1 vpn vrf AS107 Up R7(config-router-af)# *Mar 1 05:37:09.040: %BGP-5-ADJCHANGE: neighbor 17.80.1.2 vpn vrf AS107 Up R7(config-router-af)#nei 75.75.75.5 remote 200          lo R7(config-router-af)#nei 75.75.75.5 local-as 207 no R7(config-router-af)#nei 75.75.75.5 local-as 207 no-prepend R7(config-router-af)#eixt ^ % Invalid input detected at '^' marker. R7(config-router-af)#eixtnei 75.75.75.5 local-as 207 no-prepend remote 200 t 192.168.24.0 3.0 2.0 1.0 0.0 address-family ipv4 vrf AS20707 307 R7(config-router-af)# *Mar 1 05:37:41.208: %BGP-5-ADJCHANGE: neighbor 75.75.75.5 vpn vrf AS207 Up R7(config-router-af)#address-family ipv4 vrf AS307eixt nei 75.75.75.5 local-as 207 no-prepend remote 200 t 192.168.24.0 .0 .0 3.0 0.0  R7(config-router-af)#net 192.168.30.0 .0 1.0  R7(config-router-af)#net 192.168.31.0 .0 2.0  R7(config-router-af)#net 192.168.32.0 .0 3.0  R7(config-router-af)#\net 192.168.33.0 .0 4.0  R7(config-router-af)#nei 76.76.76.6 remotr 1 2 300 ^ % Invalid input detected at '^' marker. R7(config-router-af)#nei 76.76.76.6 remotr 300 300  R7(config-router-af)#nei 76.76.76.6 remot 300         lo R7(config-router-af)#nei 76.76.76.6 local-as 307 R7(config-router-af)#^Z R7# *Mar 1 05:38:18.285: %SYS-5-CONFIG_I: Configured from console by console R7#sh ip bgp R7#sh iop  p bgpo  sum R7#sh ip bgp ? A.B.C.D IP prefix /, e.g., 35.0.0.0/8 A.B.C.D Network in the BGP routing table to display cidr-only Display only routes with non-natural netmasks community Display routes matching the communities community-list Display routes matching the community-list dampening Display detailed information about dampening filter-list Display routes conforming to the filter-list inconsistent-as Display only routes with inconsistent origin ASs injected-paths Display all injected paths ipv4 Address family labels Display Labels for IPv4 NLRI specific information neighbors Detailed information on TCP and BGP neighbor connections paths Path information peer-group Display information on peer-groups prefix-list Display routes matching the prefix-list quote-regexp Display routes matching the AS path "regular expression" regexp Display routes matching the AS path regular expression rib-failure Display bgp routes that failed to install in the routing table (RIB) route-map Display routes matching the route-map summary Summary of BGP neighbor status vpnv4 Display VPNv4 NLRI specific information --More--   | Output modifiers R7#sh ip bgp vp R7#sh ip bgp vpnv4 >? % Unrecognized command R7#sh ip bgp vpnv4 > ? * Display information about all VPNv4 NLRIs all Display information about all VPNv4 NLRIs rd Display information for a route distinguisher vrf Display information for a VPN Routing/Forwarding instance R7#sh ip bgp vpnv4 vrf ? WORD VPN Routing/Forwarding instance name R7#sh ip bgp vpnv4 vrf AS107 ? A.B.C.D IP prefix /, e.g., 35.0.0.0/8 A.B.C.D Network in the BGP routing table to display cidr-only Display only routes with non-natural netmasks community Display routes matching the communities community-list Display routes matching the community-list dampening Display detailed information about dampening filter-list Display routes conforming to the filter-list inconsistent-as Display only routes with inconsistent origin ASs injected-paths Display all injected paths labels Display BGP labels for prefixes neighbors Detailed information on TCP and BGP neighbor connections paths Path information peer-group Display information on peer-groups prefix-list Display routes matching the prefix-list quote-regexp Display routes matching the AS path "regular expression" regexp Display routes matching the AS path regular expression rib-failure Display bgp routes that failed to install in the routing table (RIB) route-map Display routes matching the route-map summary Summary of BGP neighbor status | Output modifiers --More--   R7#sh ip bgp vpnv4 vrf AS107 u *Mar 1 05:38:53.174: %BGP-5-ADJCHANGE: neighbor 76.76.76.6 vpn vrf AS307 Up R7#sh ip bgp vpnv4 vrf AS107 um  sum BGP router identifier 7.7.7.7, local AS number 107 BGP table version is 129, main routing table version 129 24 network entries using 2904 bytes of memory 43 path entries using 2752 bytes of memory 25 BGP path attribute entries using 1500 bytes of memory 9 BGP AS-PATH entries using 216 bytes of memory 3 BGP extended community entries using 72 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 7444 total bytes of memory BGP activity 72/0 prefixes, 91/0 paths, scan interval 15 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 17.80.1.1 4 100 13 6 129 0 0 00:01:50 19 17.80.1.2 4 100 11 11 129 0 0 00:01:48 19 R7# R7# R7# R7#sh ip bgp vpnv4 vrf AS107 sum07 sum 207 sum BGP router identifier 7.7.7.7, local AS number 107 BGP table version is 148, main routing table version 148 24 network entries using 2904 bytes of memory 24 path entries using 1536 bytes of memory 25 BGP path attribute entries using 1500 bytes of memory 9 BGP AS-PATH entries using 216 bytes of memory 3 BGP extended community entries using 72 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 6228 total bytes of memory BGP activity 72/0 prefixes, 91/0 paths, scan interval 15 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 75.75.75.5 4 200 13 6 129 0 0 00:01:25 19 R7#sh ip bgp vpnv4 vrf AS207 sum07 sum 407 sum07 sum 307 sum BGP router identifier 7.7.7.7, local AS number 107 BGP table version is 148, main routing table version 148 24 network entries using 2904 bytes of memory 24 path entries using 1536 bytes of memory 25 BGP path attribute entries using 1500 bytes of memory 9 BGP AS-PATH entries using 216 bytes of memory 3 BGP extended community entries using 72 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 6228 total bytes of memory BGP activity 72/0 prefixes, 91/0 paths, scan interval 15 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 76.76.76.6 4 300 10 5 129 0 0 00:00:20 19 R7# R7# R7#sh ip bgp vpnv4 vrf AS307 sum    BGP table version is 148, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path Route Distinguisher: 307:1 (default for vrf AS307) *> 10.0.0.0 76.76.76.6 0 307 300 i *> 17.57.100.0/24 76.76.76.6 0 0 307 300 i *> 17.57.101.0/24 76.76.76.6 0 0 307 300 i *> 17.57.102.0/24 76.76.76.6 0 0 307 300 i *> 17.57.103.0/24 76.76.76.6 0 0 307 300 i *> 17.80.1.0/24 76.76.76.6 0 307 300 100 i *> 20.0.0.0 76.76.76.6 0 307 300 100 i *> 30.0.0.0 76.76.76.6 0 307 300 100 i *> 40.0.0.0 76.76.76.6 0 307 300 100 i *> 50.0.0.0 76.76.76.6 0 307 300 200 i *> 60.0.0.0 76.76.76.6 0 0 307 300 i *> 75.75.75.0/24 76.76.76.6 0 307 300 200 i r> 76.76.76.0/24 76.76.76.6 0 0 307 300 i *> 180.40.7.0/27 76.76.76.6 0 307 300 100 i *> 180.40.7.64/27 76.76.76.6 0 307 300 i *> 180.40.7.128/27 76.76.76.6 0 307 300 i --More--   Network Next Hop Metric LocPrf Weight Path *> 192.168.30.0 0.0.0.0 0 32768 i *> 192.168.31.0 0.0.0.0 0 32768 i *> 192.168.32.0 0.0.0.0 0 32768 i *> 192.168.33.0 0.0.0.0 0 32768 i *> 192.168.34.0 0.0.0.0 0 32768 i *> 208.28.1.0/29 76.76.76.6 0 307 300 i *> 208.28.1.64/28 76.76.76.6 0 307 300 i *> 208.28.1.128/27 76.76.76.6 0 307 300 200 i R7# RACK13AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh ip bgp BGP table version is 79, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 10.0.0.0 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.100.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.101.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.102.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.103.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i r>i17.80.1.0/24 17.80.1.2 0 100 0 i *>i20.0.0.0 180.40.7.2 0 100 0 i *> 30.0.0.0 0.0.0.0 0 32768 i *>i40.0.0.0 17.80.1.2 0 100 0 i * 50.0.0.0 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i *> 60.0.0.0 208.28.1.1 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * i 180.40.7.2 0 100 0 300 i * 75.75.75.0/24 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i *> 76.76.76.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i r>i180.40.7.0/27 180.40.7.2 0 100 0 i *> 180.40.7.64/27 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i *> 180.40.7.128/27 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i * i192.168.10.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * i192.168.11.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * i192.168.12.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * i192.168.13.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * i192.168.14.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * 192.168.20.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i --More--   Network Next Hop Metric LocPrf Weight Path * 192.168.21.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i * 192.168.22.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i * 192.168.23.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i * 192.168.24.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i *> 192.168.30.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i *> 192.168.31.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i *> 192.168.32.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i *> 192.168.33.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i *> 192.168.34.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i r> 208.28.1.0/29 208.28.1.1 0 0 300 i r i 180.40.7.2 0 100 0 300 i *> 208.28.1.64/28 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * 208.28.1.128/27 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i R3#p 192.168.11.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.11.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R3#p 192.168.11.1.1 21.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.21.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms R3#p 192.168.21.11.1 31.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.31.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3#sh ip bgp BGP table version is 79, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 10.0.0.0 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.100.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.101.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.102.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.103.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i r>i17.80.1.0/24 17.80.1.2 0 100 0 i *>i20.0.0.0 180.40.7.2 0 100 0 i *> 30.0.0.0 0.0.0.0 0 32768 i *>i40.0.0.0 17.80.1.2 0 100 0 i * 50.0.0.0 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i *> 60.0.0.0 208.28.1.1 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * i 180.40.7.2 0 100 0 300 i * 75.75.75.0/24 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i *> 76.76.76.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i r>i180.40.7.0/27 180.40.7.2 0 100 0 i *> 180.40.7.64/27 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i *> 180.40.7.128/27 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i * i192.168.10.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * i192.168.11.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * i192.168.12.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * i192.168.13.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * i192.168.14.0 17.80.1.7 0 100 0 107 i *> 17.80.1.7 0 0 107 i * 192.168.20.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i --More--   Network Next Hop Metric LocPrf Weight Path * 192.168.21.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i * 192.168.22.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i * 192.168.23.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i * 192.168.24.0 208.28.1.1 0 300 200 207 107 i *>i 180.40.7.2 0 100 0 200 207 107 i *> 192.168.30.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i *> 192.168.31.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i *> 192.168.32.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i *> 192.168.33.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i *> 192.168.34.0 208.28.1.1 0 300 307 107 i * i 180.40.7.2 0 100 0 300 307 107 i r> 208.28.1.0/29 208.28.1.1 0 0 300 i r i 180.40.7.2 0 100 0 300 i *> 208.28.1.64/28 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i --More-- RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#rouer bgp 107 ^ % Invalid input detected at '^' marker. R7(config)#rouer bgp 107outer bgp 107 R7(config-router)#add vrf     ipv4 vrf AS307 R7(config-router-af)#add ipv4 vrf AS307router bgp 107 er bgp 107 nei 76.76.76.6 local-as 307 no R7(config-router-af)#nei 76.76.76.6 local-as 307 no-prepend R7(config-router-af)#do sh ru *Mar 1 05:41:51.647: %BGP-5-ADJCHANGE: neighbor 76.76.76.6 vpn vrf AS307 Down Local AS change R7(config-router-af)#do sh ru | b    n | b bgp router bgp 107 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes no auto-summary ! address-family ipv4 vrf AS307 neighbor 76.76.76.6 remote-as 300 neighbor 76.76.76.6 local-as 307 no-prepend neighbor 76.76.76.6 activate no auto-summary no synchronization network 192.168.30.0 network 192.168.31.0 network 192.168.32.0 network 192.168.33.0 network 192.168.34.0 exit-address-family ! address-family ipv4 vrf AS207 neighbor 75.75.75.5 remote-as 200 neighbor 75.75.75.5 local-as 207 no-prepend neighbor 75.75.75.5 activate --More--   no auto-summary no synchronization network 192.168.20.0 network 192.168.21.0 network 192.168.22.0 network 192.168.23.0 network 192.168.24.0 exit-address-family ! address-family ipv4 vrf AS107 neighbor 17.80.1.1 remote-as 100 neighbor 17.80.1.1 activate neighbor 17.80.1.2 remote-as 100 neighbor 17.80.1.2 activate no auto-summary no synchronization network 192.168.10.0 network 192.168.11.0 network 192.168.12.0 network 192.168.13.0 network 192.168.14.0 exit-address-family ! --More-- *Mar 1 05:42:32.594: %BGP-5-ADJCHANGE: neighbor 76.76.76.6 vpn vrf AS307 Up --More--   R7(config-router-af)#^Z R7# *Mar 1 05:44:16.669: %SYS-5-CONFIG_I: Configured from console by console R7# RACK13AS>3 [Resuming connection 3 to r3 ... ]  * 208.28.1.128/27 208.28.1.1 0 300 200 i --More--   R3#sh run|  | b bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes network 30.0.0.0 neighbor 17.80.1.2 remote-as 100 neighbor 17.80.1.2 route-reflector-client neighbor 17.80.1.7 remote-as 107 neighbor 180.40.7.2 remote-as 100 neighbor 208.28.1.1 remote-as 300 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! --More--   R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] 05 R4#sh run | b bgp router bgp 100 no synchronization bgp router-id 4.4.4.4 bgp log-neighbor-changes network 17.80.1.0 mask 255.255.255.0 network 40.0.0.0 neighbor 17.80.1.1 remote-as 100 neighbor 17.80.1.1 route-map FromR3 in neighbor 17.80.1.7 remote-as 107 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! route-map FromR3 permit 10 set ip next-hop peer-address ! ! ! dial-peer cor custom --More-- RACK13AS>5 [Resuming connection 5 to r5 ... ] 05:40:31 S5#sh run | b 0/7 interface FastEthernet0/7 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable ! interface FastEthernet0/14 --More--   switchport mode dynamic desirable ! interface FastEthernet0/15 switchport mode dynamic desirable ! interface FastEthernet0/16 switchport mode dynamic desirable ! interface FastEthernet0/17 switchport mode dynamic desirable ! interface FastEthernet0/18 switchport mode dynamic desirable ! interface FastEthernet0/19 switchport mode dynamic desirable ! interface FastEthernet0/20 switchport mode dynamic desirable ! interface FastEthernet0/21 switchport mode dynamic desirable ! --More--  interface FastEthernet0/22 switchport mode dynamic desirable ! interface FastEthernet0/23 switchport mode dynamic desirable ! interface FastEthernet0/24 switchport mode dynamic desirable ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address shutdown ! interface Vlan10 ip address 208.28.1.65 255.255.255.240 ! interface Vlan20 --More--   ip address 208.28.1.130 255.255.255.224 ! interface Vlan75 ip address 75.75.75.5 255.255.255.0 ! router bgp 200 no synchronization bgp router-id 5.5.5.5 bgp log-neighbor-changes network 50.0.0.0 network 75.75.75.0 mask 255.255.255.0 network 208.28.1.128 mask 255.255.255.224 neighbor 75.75.75.7 remote-as 207 neighbor 208.28.1.66 remote-as 300 neighbor 208.28.1.129 remote-as 100 no auto-summary ! ip classless ip http server ip http secure-server ! ! ! --More-- RACK13AS>6 [Resuming connection 6 to r6 ... ] 05:41:41: %B S6(config-router)#^Z S6#sh run | 05:48:40: %SYS-5-CONFIG_I: Configured from console by consoleb Vla interface Vlan1 no ip address shutdown ! interface Vlan76 ip address 76.76.76.6 255.255.255.0 ! router bgp 300 no synchronization bgp router-id 6.6.6.6 bgp log-neighbor-changes network 17.57.100.0 mask 255.255.255.0 network 17.57.101.0 mask 255.255.255.0 network 17.57.102.0 mask 255.255.255.0 network 17.57.103.0 mask 255.255.255.0 network 60.0.0.0 network 76.76.76.0 mask 255.255.255.0 neighbor 17.57.100.1 remote-as 300 neighbor 76.76.76.7 remote-as 307 no auto-summary ! ip classless ip http server --More-- RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b bgp   Lo  I ip   vrf    vrf ip vrf AS107 rd 107:1 route-target export 107:1 route-target import 107:1 ! ip vrf AS207 rd 207:1 route-target export 207:1 route-target import 207:1 ! ip vrf AS307 rd 307:1 route-target export 307:1 route-target import 307:1 ! ip audit po max-events 100 ! ! ! ! ! ! ! --More--  ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback107 description Routes for AS107 ip vrf forwarding AS107 ip address 192.168.11.1 255.255.255.0 secondary ip address 192.168.12.1 255.255.255.0 secondary ip address 192.168.13.1 255.255.255.0 secondary ip address 192.168.14.1 255.255.255.0 secondary ip address 192.168.10.1 255.255.255.0 ! interface Loopback207 --More--   description Routes for AS207 ip vrf forwarding AS207 ip address 192.168.21.1 255.255.255.0 secondary ip address 192.168.22.1 255.255.255.0 secondary ip address 192.168.23.1 255.255.255.0 secondary ip address 192.168.24.1 255.255.255.0 secondary ip address 192.168.20.1 255.255.255.0 ! interface Loopback307 description Routes for AS307 ip vrf forwarding AS307 ip address 192.168.31.1 255.255.255.0 secondary ip address 192.168.32.1 255.255.255.0 secondary ip address 192.168.33.1 255.255.255.0 secondary ip address 192.168.34.1 255.255.255.0 secondary ip address 192.168.30.1 255.255.255.0 ! interface FastEthernet0/0 no ip address duplex auto speed auto ! interface FastEthernet0/0.30 --More--   encapsulation dot1Q 30 ip vrf forwarding AS107 ip address 17.80.1.7 255.255.255.0 no snmp trap link-status ! interface FastEthernet0/0.75 encapsulation dot1Q 75 ip vrf forwarding AS207 ip address 75.75.75.7 255.255.255.0 no snmp trap link-status ! interface FastEthernet0/0.76 encapsulation dot1Q 76 ip vrf forwarding AS307 ip address 76.76.76.7 255.255.255.0 no snmp trap link-status ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address --More--   shutdown duplex auto speed auto ! interface Serial1/0 no ip address shutdown ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown --More--  ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router bgp 107 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes no auto-summary ! address-family ipv4 vrf AS307 neighbor 76.76.76.6 remote-as 300 neighbor 76.76.76.6 local-as 307 no-prepend neighbor 76.76.76.6 activate --More--   no auto-summary no synchronization network 192.168.30.0 network 192.168.31.0 network 192.168.32.0 network 192.168.33.0 network 192.168.34.0 exit-address-family ! address-family ipv4 vrf AS207 neighbor 75.75.75.5 remote-as 200 neighbor 75.75.75.5 local-as 207 no-prepend neighbor 75.75.75.5 activate no auto-summary no synchronization network 192.168.20.0 network 192.168.21.0 network 192.168.22.0 network 192.168.23.0 network 192.168.24.0 exit-address-family ! address-family ipv4 vrf AS107 --More--   neighbor 17.80.1.1 remote-as 100 neighbor 17.80.1.1 activate neighbor 17.80.1.2 remote-as 100 neighbor 17.80.1.2 activate no auto-summary no synchronization network 192.168.10.0 network 192.168.11.0 network 192.168.12.0 network 192.168.13.0 network 192.168.14.0 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! --More--