=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2007.02.26 17:54:59 =~=~=~=~=~=~=~=~=~=~=~= confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int vlan 1`0  0 S5(config-if)# 05:05:16: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to down S5(config-if)#do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S5(config-if)#do sh ip int bri Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 unassigned YES unset down down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down --More--   S5(config-if)#ip add 208.28.1.65 255.255.255.12  240 S5(config-if)#exit S5(config)#vlan 10 S5(config-vlan)#nme    ame ToR1 S5(config-vlan)#do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S5(config-vlan)#exit S5(config)#exitdo sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 ToR1 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 --More--   S5(config)#do sh vlanexit do sh vlanname ToR1 vlan 10 exit ip add 208.28.1.65 255.255.255.240do sh ip int bri  Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual up down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down --More--   S5(config)#do sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1 S5(config)#do sh int trunp int bri Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual up up FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 05:06:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down --More--   S5(config)#vlan 20 S5(config-vlan)#name R Tr  ToR2 S5(config-vlan)#exit S5(config)#int vlan 20 S5(config-if)#ip add 208 05:07:23: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down S5(config-if)#ip add 208.28.1.130 2545  5.255.255.224 S5(config-if)#int fa 0/1 S5(config-if)#s S5(config-if)#sw S5(config-if)#switchport mo S5(config-if)#switchport mode d ac S5(config-if)#switchport mode access S5(config-if)#sw S5(config-if)#switchport 05:07:51: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up S5(config-if)#switchport ac S5(config-if)#switchport access v S5(config-if)#switchport access vlan 19 0 S5(config-if)#exit S5(config)#vlan 30 S5(config-vlan)#name BlueSuede S5(config-vlan)#exit S5(config)#int fa 0/3 S5(config-if)#sw S5(config-if)#switchport m S5(config-if)#switchport mode ac S5(config-if)#switchport mode access S5(config-if)#s S5(config-if)#sw S5(config-if)#switchport acc S5(config-if)#switchport access v S5(config-if)#switchport access vlan 30 S5(config-if)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S6#shj    vtp stata ^ % Invalid input detected at '^' marker. S6#sh vtp stata  VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 1005 Number of existing VLANs : 5 VTP Operating Mode : Server VTP Domain Name : VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x57 0xCD 0x40 0x65 0x63 0x59 0x47 0xBD Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00 Local updater ID is 0.0.0.0 (no valid interface found) S6# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5(config-if)#rx  exit S5(config)#vtp dom S5(config)#vtp domain Graceland Changing VTP domain name from NULL to Graceland S5(config)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 ToR1 active 20 ToR2 active 30 BlueSuede active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 --More--   S6#sh s vtp stat VTP Version : 2 Configuration Revision : 3 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x1E 0x48 0x0E 0x22 0x95 0x3D 0xA8 0x84 Configuration last modified by 208.28.1.65 at 3-1-93 05:08:19 Local updater ID is 0.0.0.0 (no valid interface found) S6# S6# S6# S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/4 S6(config-if)#sw S6(config-if)#switchport mo S6(config-if)#switchport mode ac S6(config-if)#switchport mode access S6(config-if)#sw S6(config-if)#switchport acc vl 30 S6(config-if)#int fa0/2 S6(config-if)#int fa0/2switchport acc vl 30mode access S6(config-if)#switchport mode access int fa0/2 switchport acc vl 30  20 S6(config-if)#int fa 0/1 S6(config-if)#ip add 17.57.100.2 255.255.255.0 ^ % Invalid input detected at '^' marker. S6(config-if)#no sw S6(config-if)#no switchport S6(config-if)#no switchport ip add 17.57.100.2 255.255.255.0 S6(config-if)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Ethernet0/1 unassigned YES unset administratively down down Serial0/1 unassigned YES unset administratively down down R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int fa 0/     e 0/1 R1(config-if)#ip add 17,.57    .57.100.1 255.255.255.0 R1(config-if)#no shut R1(config-if)#^Z R1# *Mar 1 05:09:40.421: %SYS-5-CONFIG_I: Configured from console by console R1# *Mar 1 05:09:41.992: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up *Mar 1 05:09:42.994: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed state to up R1#p 208.28.1.65 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: ..!!! Success rate is 60 percent (3/5), round-trip min/avg/max = 1/2/4 ms R1#p 17.57.100.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: ..!!! Success rate is 60 percent (3/5), round-trip min/avg/max = 1/3/4 ms R1# R1# R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#p 208.28.1.130 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: ..!!! Success rate is 60 percent (3/5), round-trip min/avg/max = 1/2/4 ms R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#p 17.80.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/3/4 ms R3# R3# R3# R3# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5(config)#vtp pr S5(config)#vtp pruning Pruning switched on S5(config)#^Z S5# 05:13:48: %SYS-5-CONFIG_I: Configured from console by console S5# S5#sh vtp stat VTP Version : 2 Configuration Revision : 4 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x3B 0xBF 0xA9 0xF5 0x31 0x08 0x53 0x2B Configuration last modified by 208.28.1.65 at 3-1-93 05:13:40 Local updater ID is 208.28.1.65 on interface Vl10 (lowest numbered VLAN interface found) S5#sh int tu rumn   Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,30 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,20,30 S5#sh eu  run Building configuration... Current configuration : 2381 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname S5 ! ! no aaa new-model ip subnet-zero no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst --More--  spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport access vlan 10 switchport mode access ! interface FastEthernet0/2 switchport mode dynamic desirable shutdown ! interface FastEthernet0/3 switchport access vlan 30 switchport mode access ! interface FastEthernet0/4 switchport mode dynamic desirable shutdown ! interface FastEthernet0/5 switchport mode dynamic desirable --More--  ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 switchport mode dynamic desirable ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 --More--   switchport mode dynamic desirable ! interface FastEthernet0/14 switchport mode dynamic desirable ! interface FastEthernet0/15 switchport mode dynamic desirable ! interface FastEthernet0/16 switchport mode dynamic desirable ! interface FastEthernet0/17 switchport mode dynamic desirable ! interface FastEthernet0/18 switchport mode dynamic desirable ! interface FastEthernet0/19 switchport mode dynamic desirable ! interface FastEthernet0/20 switchport mode dynamic desirable ! --More--  interface FastEthernet0/21 switchport mode dynamic desirable ! interface FastEthernet0/22 switchport mode dynamic desirable ! interface FastEthernet0/23 switchport mode dynamic desirable ! interface FastEthernet0/24 switchport mode dynamic desirable ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address shutdown ! interface Vlan10 --More--   ip address 208.28.1.65 255.255.255.240 ! interface Vlan20 ip address 208.28.1.130 255.255.255.224 ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 no login line vty 5 15 no login ! ! --More--   S5#vlan data % Warning: It is recommended to configure VLAN from config mode, as VLAN database mode is being deprecated. Please consult user documentation for configuring VTP/VLAN in config mode. S5(vlan)# S5(vlan)# S5(vlan)#sh cur S5(vlan)#sh current VLAN ISL Id: 1 Name: default Media Type: Ethernet VLAN 802.10 Id: 100001 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 10 Name: ToR1 Media Type: Ethernet VLAN 802.10 Id: 100010 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 20 Name: ToR2 Media Type: Ethernet VLAN 802.10 Id: 100020 State: Operational --More--   MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 30 Name: BlueSuede Media Type: Ethernet VLAN 802.10 Id: 100030 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 1002 Name: fddi-default Media Type: FDDI VLAN 802.10 Id: 101002 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 1003 --More--   Name: token-ring-default Media Type: Token Ring VLAN 802.10 Id: 101003 State: Operational MTU: 1500 Maximum ARE Hop Count: 7 Maximum STE Hop Count: 7 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 1004 Name: fddinet-default Media Type: FDDI Net VLAN 802.10 Id: 101004 State: Operational MTU: 1500 STP Type: IEEE Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 1005 Name: trnet-default Media Type: Token Ring Net --More--   VLAN 802.10 Id: 101005 State: Operational MTU: 1500 STP Type: IBM Backup CRF Mode: Disabled Remote SPAN VLAN: No S5(vlan)#vtp ? client Set the device to client mode. domain Set the name of the VTP administrative domain. password Set the password for the VTP administrative domain. pruning Set the administrative domain to permit pruning. server Set the device to server mode. transparent Set the device to transparent mode. v2-mode Set the administrative domain to V2 mode. S5(vlan)#vtp     ^Z S5# 05:15:45: %SYS-5-CONFIG_I: Configured from console by console S5# RACK13AS>6 [Resuming connection 6 to r6 ... ] 05 S6(config-if)#^Z S6#sh run | b 05:18:14: %SYS-5-CONFIG_I: Configured from console by console S6#sh run | b 0/1 interface FastEthernet0/1 no switchport ip address 17.57.100.2 255.255.255.0 ! interface FastEthernet0/2 switchport access vlan 20 switchport mode access ! interface FastEthernet0/3 switchport mode dynamic desirable shutdown ! interface FastEthernet0/4 switchport access vlan 30 switchport mode access ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 --More--   switchport mode dynamic desirable --More--  ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable ! interface FastEthernet0/14 switchport mode dynamic desirable ! interface FastEthernet0/15 --More--   S6# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#sh V run | b Vlan interface Vlan1 no ip address shutdown ! interface Vlan10 ip address 208.28.1.65 255.255.255.240 ! interface Vlan20 ip address 208.28.1.130 255.255.255.224 ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 --More--   S5#sh vtp stat VTP Version : 2 Configuration Revision : 4 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x3B 0xBF 0xA9 0xF5 0x31 0x08 0x53 0x2B Configuration last modified by 208.28.1.65 at 3-1-93 05:13:40 Local updater ID is 208.28.1.65 on interface Vl10 (lowest numbered VLAN interface found) S5#cofn  nfi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa0/24 S5(config-if)#sw S5(config-if)#switchport mote    de tr S5(config-if)#switchport mode trunk Command rejected: An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode. S5(config-if)#switchport mode trunk            tr S5(config-if)#switchport trunk ? allowed Set allowed VLAN characteristics when interface is in trunking mode encapsulation Set trunking encapsulation when interface is in trunking mode native Set trunking native characteristics when interface is in trunking mode pruning Set pruning VLAN characteristics when interface is in trunking mode S5(config-if)#switchport trunk e S5(config-if)#switchport trunk encapsulation ? dot1q Interface uses only 802.1q trunking encapsulation when trunking isl Interface uses only ISL trunking encapsulation when trunking negotiate Device will negotiate trunking encapsulation with peer on interface S5(config-if)#switchport trunk encapsulation do S5(config-if)#switchport trunk encapsulation dot1q S5(config-if)#switchport trunk encapsulation dot1q 05:33:19: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down 05:33:19: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down S5(config-if)#switchport trunk encapsulation dot1q mode trunk  S5(config-if)# 05:33:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up S5(config-if)# 05:33:52: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up S5(config-if)#sw S5(config-if)#switchport tr S5(config-if)#switchport trunk al S5(config-if)#switchport trunk allowed ? vlan Set allowed VLANs when interface is in trunking mode S5(config-if)#switchport trunk allowed vl S5(config-if)#switchport trunk allowed vlan ? WORD VLAN IDs of the allowed VLANs when this port is in trunking mode add add VLANs to the current list all all VLANs except all VLANs except the following none no VLANs remove remove VLANs from the current list S5(config-if)#switchport trunk allowed vlan 10,16,20,30 S5(config-if)#sw S5(config-if)#switchport no S5(config-if)#switchport nonegotiate S5(config-if)#^Z S5#sh run 05:35:50: %SYS-5-CONFIG_I: Configured from console by console S5#sh run int fa 0/24 Building configuration... Current configuration : 162 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport trunk allowed vlan 10,16,20,30 switchport mode trunk switchport nonegotiate end S5# RACK13AS>6 [Resuming connection 6 to r6 ... ] 05: S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#interface FastEthernet0/24 S6(config-if)# switchport trunk encapsulation dot1q S6(config-if)# switchport trunk allowed vlan 10,16,20,30 S6(config-if)# switchport mode trunk S6(config-if)# switchport nonegotiate S6(config-if)#^Z S6# 05:37:27: %SYS-5-CONFIG_I: Configured from console by console S6#sh t run int fa 0/24 Building configuration... Current configuration : 162 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport trunk allowed vlan 10,16,20,30 switchport mode trunk switchport nonegotiate end S6# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh fram pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 2 0 0 0 Switched 0 0 0 0 Unused 0 1 0 0 DLCI = 301, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 365 output pkts 27 in bytes 118996 out bytes 918 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 27 out bcast bytes 918 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:35:49, last time pvc status changed 05:35:39 --More--   DLCI = 302, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 27 output pkts 15 in bytes 918 out bytes 510 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 15 out bcast bytes 510 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:35:53, last time pvc status changed 05:35:43 --More--   DLCI = 307, DLCI USAGE = UNUSED, PVC STATUS = INACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:35:55, last time pvc status changed 05:35:55 R3#sh fram map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#no fra R3(config-if)#no fram R3(config-if)#no frame-relay inv R3(config-if)#no frame-relay inverse-arp R3(config-if)#fram amp     map ip ad    208.28.1.1 301 br R3(config-if)#fram map ip 208.28.1.1 301 broadcast R3(config-if)#fram map ip 208.28.1.1 301 broadcast  broadcast 2 broadcast  302 broadcast 3 302 broadcast  R3(config-if)#^Z R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh run int s 0/0.1 Building configuration... Current configuration : 118 bytes ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 end R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s 1/0.1 Building configuration... Current configuration : 111 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay interface-dlci 203 end R2#sh fram pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 1 0 0 0 Switched 0 0 0 0 Unused 1 1 0 0 DLCI = 201, DLCI USAGE = UNUSED, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:38:39, last time pvc status changed 05:38:19 --More--   DLCI = 203, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.1 input pkts 28 output pkts 14 in bytes 952 out bytes 476 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 14 out bcast bytes 476 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:38:53, last time pvc status changed 05:38:40 --More--   DLCI = 207, DLCI USAGE = UNUSED, PVC STATUS = INACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:38:52, last time pvc status changed 05:38:52 R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#p 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/68/96 ms R3#p 208.28.1.1 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#p 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/124/153 ms R1#p 208.28.1.1 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/61/65 ms R1#p 208.28.1.2 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: .. RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#deb ip icmp ICMP packet debugging is on R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] .. R1#p 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: RACK13AS>2 [Resuming connection 2 to r2 ... ] R2# *Mar 1 05:42:31.368: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:42:33.371: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:42:35.375: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:42:37.378: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:42:39.385: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2#u all All possible debugging has been turned off R2#deb fram pack Frame Relay packet debugging is on R2# R2# R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] .. R1#p 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: RACK13AS>2 [Resuming connection 2 to r2 ... ] R2# *Mar 1 05:42:55.227: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:55.227: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:42:57.226: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:57.230: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:42:59.230: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:59.234: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:43:01.241: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:43:01.241: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:43:03.256: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:43:03.256: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2#conifi t ^ % Invalid input detected at '^' marker. R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)#fram map ip 208.28.1.1 203 R2(config-subif)# RACK13AS>1 [Resuming connection 1 to r1 ... ] .. R1#p 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/118/128 ms R1#sh fram map Serial0/0.1 (up): point-to-point dlci, dlci 103(0x67,0x1870), broadcast status defined, active R1# R1# R1# R1# R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] * R2(config-subif)#do sh run int s 1/0.1 Building configuration... Current configuration : 146 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay interface-dlci 203 end R2(config-subif)#do sh run int s 1/0.1 frame-relay map ip 208.28.1.1 2031 203 2 203 R2(config-subif)#frame-relay map ip 208.28.1.2 203 br R2(config-subif)#m no frame-relay interface-dlci 203 %Cannot remove PVC as being referenced by map statement R2(config-subif)#do shno frame-relay interface-dlci 203frame-relay map ip 208.28.1.2 203 br do sh run int s 1/0.1  Building configuration... Current configuration : 191 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 broadcast frame-relay interface-dlci 203 end R2(config-subif)#no frame-relay map ip 208.28.1.1 203 R2(config-subif)#no frame-relay map ip 208.28.1.2 203 broadcast R2(config-subif)#no frame-relay map ip 208.28.1.2 203 broadcast1 203 do sh run int s 1/0.1 no frame-relay interface-dlci 203 R2(config-subif)#no frame-relay interface-dlci 203map ip 208.28.1.2 203 broadcastinterface-dlci 203   frame-relay map ip 208.28.1.2 203 broadcast R2(config-subif)# frame-relay map ip 208.28.1.1 203 R2(config-subif)# R2(config-subif)#^Z R2# *Mar 1 05:50:27.028: %SYS-5-CONFIG_I: Configured from console by console R2# R2# R2#sh run int s 1/0.1 Building configuration... Current configuration : 159 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 broadcast end R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/0 Building configuration... Current configuration : 244 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.3 302 broadcast no frame-relay inverse-arp end R3#p 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: .. RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh fram mapp 208.28.1.323 1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/125/140 ms R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] .. R3#deb fram pack Frame Relay packet debugging is on R3#deb fram packp 208.28.1.2  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: *Mar 1 05:52:05.020: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:52:07.024: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:52:08.302: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 353 *Mar 1 05:52:09.027: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:52:11.026: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:52:13.030: Serial1/0:Encaps failed--no map entry link 7(IP). Success rate is 0 percent (0/5) R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#u all All possible debugging has been turned off R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#con f  t % Ambiguous command: "con t" R3# R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#fram map ip 208.28.1.2 302 R3(config-if)#^Z R3#conf t tp 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: *Mar 1 05:53:00.555: %SYS-5-CONFIG_I: Configured from console by console!!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/119/128 ms R3# *Mar 1 05:53:02.511: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:02.559: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 60 *Mar 1 05:53:02.579: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:53:02.579: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:02.639: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:53:02.639: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:02.695: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:53:02.695: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:02.755: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:53:02.755: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:02.811: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05 R3#:53:02.815: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:02.871: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:53:02.871: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:02.931: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:53:02.931: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:02.987: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:53:02.987: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:03.048: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:53:03.048: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:53:03.104: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 R3# *Mar 1 05:53:08.296: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 353 R3# *Mar 1 05:54:08.274: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 353 R3# *Mar 1 05:55:08.349: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 353 R3#u all All possible debugging has been turned off R3# R3# R3# R3#s  b   h run int s 1/0 Building configuration... Current configuration : 279 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 broadcast no frame-relay inverse-arp end R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#user One pass For-th  The-Money R3(config)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#cp onf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#user Two pass For-The-Shpw  ow R2(config)#int s 1/2 R2(config-if)#no shut       shut R2(config-if)# *Mar 1 05:58:21.662: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 05:58:22.663: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R2(config-if)#wn  en ppp R2(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 R3(config)#int s 1/2 R3(config-if)#en ppp R3(config-if)#ppp authen pap R3(config-if)#ppp ? accm Set initial Async Control Character Map accounting Set PPP network accounting method acfc Options for HDLC Address & Control Field Compression authentication Set PPP link authentication method authorization Set PPP network authorization method bridge Enable PPP bridge translation caller Caller option when no CLID is available chap Set CHAP authentication parameters direction Override default PPP direction dnis Authentication via DNIS before LCP eap Set EAP authentication parameters encrypt Enable PPP encryption ipcp Set IPCP negotiation options iphc Set IPCP Header Compression control options lcp PPP LCP configuration link Set miscellaneous link parameters loopback PPP loopback options max-bad-auth Allow multiple authentication failures max-configure Number of conf-reqs sent before assuming peer is unable to respond max-failure Number of conf-naks sent before assuming configuration is not converging --More--   max-terminate Number of term-reqs sent before assuming peer is unable to respond ms-chap Set MS-CHAP authentication parameters ms-chap-v2 Set MS-CHAP-V2 authentication parameters multilink Make interface multilink capable pap Set PAP authentication parameters pfc Options for Protocol Field Compression quality Set parameters related to Link Quality Monitoring (LQM) reliable-link Use LAPB with PPP to provide a reliable link timeout Set PPP timeout parameters R3(config-if)#ppp pp    ap  pa /      autheh n pap ? WORD Use an authentication list with this name callback Authenticate remote on callback only callin Authenticate remote on incoming call only callout Authenticate remote on outgoing call only chap Challenge Handshake Authentication Protocol (CHAP) default Use the default authentication list eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) one-time Allow use of username*OTP for one-time passwords optional Allow peer to refuse to authenticate R3(config-if)#ppp authen pap            pap ? refuse Refuse to authenticate using PAP sent-username Set outbound PAP username wait Wait for caller to authenticate first R3(config-if)#ppp pap ser R3(config-if)#ppp pap ser  R3(config-if)#ppp pap sent-username Tweo  o ? password Set outbound PAP password R3(config-if)#ppp pap sent-username Two pas R3(config-if)#ppp pap sent-username Two password For-The-Show R3(config-if)#ppp pap sent-username Two password For-The-Showauthen pap  ? WORD Use an authentication list with this name callback Authenticate remote on callback only callin Authenticate remote on incoming call only callout Authenticate remote on outgoing call only chap Challenge Handshake Authentication Protocol (CHAP) default Use the default authentication list eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) one-time Allow use of username*OTP for one-time passwords optional Allow peer to refuse to authenticate R3(config-if)#ppp authen pap optional R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#exut ^ % Invalid input detected at '^' marker. R2(config-if)#exit R2(config)#exitutn pppshut int s 1/2user Two pass For-The-Shownuser Two pass For-The-Showouser Two pass For-The-Show user Two pass For-The-Show R2(config)#int s 1/2 R2(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 113 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp shutdown clock rate 64000 end R2(config-if)# RACK13AS> [Resuming connection 2 to r2 ... ] R2(config-if)#do deb ppp ne PPP protocol negotiation debugging is on R2(config-if)#no h   shut R2(config-if)# *Mar 1 06:03:27.339: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:03:27.363: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:03:27.387: Se1/2 PPP: Outbound cdp packet dropped R2(config-if)# *Mar 1 06:03:29.314: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 06:03:29.342: Se1/2 PPP: Using default call direction *Mar 1 06:03:29.346: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:03:29.346: Se1/2 PPP: Session handle[CE000000] Session id[1] *Mar 1 06:03:29.346: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:03:29.346: Se1/2 LCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 06:03:29.346: Se1/2 LCP: MagicNumber 0x14ADC24D (0x050614ADC24D) *Mar 1 06:03:29.350: Se1/2 LCP: I CONFREQ [REQsent] id 1 len 14 *Mar 1 06:03:29.354: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:03:29.354: Se1/2 LCP: MagicNumber 0x14CBC498 (0x050614CBC498) *Mar 1 06:03:29.354: Se1/2 LCP: O CONFNAK [REQsent] id 1 len 9 *Mar 1 06:03:29.354: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:03:29.354: Se1/2 LCP: I CONFACK [REQsent] id 1 len 10 *Mar 1 06:03:29.354: Se1/2 LCP: MagicNumber 0x14ADC24D (0x050614ADC24D) *Mar 1 06:03: R2(config-if)#29.362: Se1/2 LCP: I CONFREQ [ACKrcvd] id 2 len 14 *Mar 1 06:03:29.362: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:03:29.362: Se1/2 LCP: MagicNumber 0x14CBC498 (0x050614CBC498) *Mar 1 06:03:29.362: Se1/2 LCP: O CONFNAK [ACKrcvd] id 2 len 9 *Mar 1 06:03:29.362: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:03:29.370: Se1/2 LCP: I CONFREQ [ACKrcvd] id 3 len 14 *Mar 1 06:03:29.370: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:03:29.374: Se1/2 LCP: MagicNumber 0x14CBC498 (0x050614CBC498) *Mar 1 06:03:29.374: Se1/2 LCP: O CONFNAK [ACKrcvd] id 3 len 9 *Mar 1 06:03:29.374: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:03:29.382: Se1/2 LCP: I CONFREQ [ACKrcvd] id 4 len 14 *Mar 1 06:03:29.382: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:03:29.382: Se1/2 LCP: MagicNumber 0x14CBC498 (0x050614CBC498) *Mar 1 06:03:29.382: Se1/2 LCP: O CONFNAK [ACKrcvd] id 4 len 9 *Mar 1 06:03:29.382: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:03:29.390: Se1/2 LCP: I CONFREQ [ACKrcvd] id 5 len 14 *Mar 1 06:03:29.390: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:03:29.390: Se1/2 LCP: MagicNumber 0x14CBC498 (0x050614CBC498) *Mar 1 06:03:29.390: Se1/2 LCP: O CONFNAK [ACKrcvd] id 5 len 9 *Mar 1 06:03:29.394: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:03:29.398: Se1/2 LCP: I CONFREQ [ACKrcvd] id 6 len 14 *Mar 1 06:03:29.402: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:03:29.402: Se1/2 LCP: MagicNumber 0x14CBC498 (0x050614CBC498) *Mar 1 06:03:29.402: Se1/2 LCP: O CONFREJ [ACKrcvd] id 6 len 8 *Mar 1 06:03:29.402: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:03:29.410: Se1/2 LCP: I CONFREQ [ACKrcvd] id 7 len 10 *Mar 1 06:03:29.410: Se1/2 LCP: MagicNumber 0x14CBC498 (0x050614CBC498) *Mar 1 06:03:29.410: Se1/2 LCP: O CONFACK [ACKrcvd] id 7 len 10 *Mar 1 06:03:29.410: Se1/2 LCP: MagicNumber 0x14CBC498 (0x050614CBC498) *Mar 1 06:03:29.410: Se1/2 LCP: State is Open *Mar 1 06:03:29.410: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:03:29.414: Se1/2 PPP: Phase is ESTABLISHING, Finish LCP *Mar 1 06:03:29.414: Se1/2 PPP: Phase is UP *Mar 1 06:03:29.414: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 06:03:29.414: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:03:29.418: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 06:03:29.418: Se1/2 PPP: Process pending ncp packets *Mar 1 06:03:29.418: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 06:03:29.422: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:03:29.422: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 06:03:29.422: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:03:29.422: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 06:03:29.422: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 06:03:29.426: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 06:03:29.426: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:03:29.426: Se1/2 IPCP: State is Open *Mar 1 06:03:29.426: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 06:03:29.426: Se1/2 CDPCP: State is Open *Mar 1 06:03:29.430: Se1/2 IPCP: Install route to 180.40.7.3 *Mar 1 06:03:29.430: Se1/2 IPCP: Add link info for cef entry 180.40.7.3 *Mar 1 06:03:30.416: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2(config-if)# R2(config-if)# R2(config-if)# R2(config-if)#shut~ ^ % Invalid input detected at '^' marker. R2(config-if)#shut~~  \ ^ % Invalid input detected at '^' marker. R2(config-if)#shut\  R2(config-if)#ppp *Mar 1 06:05:43.250: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down R2(config-if)#ppp a *Mar 1 06:05:43.254: Se1/2 PPP: Sending Acct Event[Down] id[3] *Mar 1 06:05:43.254: Se1/2 CDPCP: State is Closed *Mar 1 06:05:43.258: Se1/2 IPCP: State is Closed *Mar 1 06:05:43.258: Se1/2 IPCP: Remove link info for cef entry 180.40.7.3 *Mar 1 06:05:43.258: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:05:43.258: Se1/2 LCP: State is Closed *Mar 1 06:05:43.258: Se1/2 PPP: Phase is DOWN *Mar 1 06:05:43.258: Se1/2 IPCP: Remove route to 180.40.7.3 R2(config-if)#ppp auther *Mar 1 06:05:44.251: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R2(config-if)#ppp auther  pap R2(config-if)#ppp pap se R2(config-if)#ppp pap sent-username R2 pass cisco R2(config-if)#no shut R2(config-if)# *Mar 1 06:06:09.545: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:06:09.569: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:06:09.593: Se1/2 PPP: Outbound cdp packet dropped R2(config-if)# *Mar 1 06:06:11.524: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 06:06:11.524: Se1/2 PPP: Using default call direction *Mar 1 06:06:11.524: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:06:11.524: Se1/2 PPP: Session handle[5B000001] Session id[2] *Mar 1 06:06:11.524: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:06:11.524: Se1/2 LCP: O CONFREQ [Closed] id 2 len 14 *Mar 1 06:06:11.524: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:11.528: Se1/2 LCP: MagicNumber 0x14B03BCF (0x050614B03BCF) *Mar 1 06:06:11.528: Se1/2 LCP: I CONFREQ [REQsent] id 8 len 14 *Mar 1 06:06:11.528: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:11.528: Se1/2 LCP: MagicNumber 0x14CE3E17 (0x050614CE3E17) *Mar 1 06:06:11.528: Se1/2 LCP: O CONFACK [REQsent] id 8 len 14 *Mar 1 06:06:11.528: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:11.528: Se1/2 LCP: MagicNumber 0x14CE3E17 (0x050614CE3E17) *Mar 1 06:06:11.5 R2(config-if)#36: Se1/2 LCP: I CONFACK [ACKsent] id 2 len 14 *Mar 1 06:06:11.536: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:11.536: Se1/2 LCP: MagicNumber 0x14B03BCF (0x050614B03BCF) *Mar 1 06:06:11.536: Se1/2 LCP: State is Open *Mar 1 06:06:11.536: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:06:11.536: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:06:11.536: Se1/2 PAP: Using password from interface PAP *Mar 1 06:06:11.536: Se1/2 PAP: O AUTH-REQ id 1 len 13 from "R2" *Mar 1 06:06:11.540: Se1/2 PAP: I AUTH-REQ id 1 len 21 from "Two" *Mar 1 06:06:11.540: Se1/2 PAP: Authenticating peer Two *Mar 1 06:06:11.540: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:06:11.540: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:06:11.544: Se1/2 PAP: O AUTH-NAK id 1 len 26 msg is "Authentication failed" *Mar 1 06:06:11.544: Se1/2 PPP: Sending Acct Event[Down] id[4] *Mar 1 06:06:11.544: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:06:11.544: Se1/2 LCP: O TERMREQ [Open] id 3 len 4 *Mar 1 06:06:11.548: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:06:11.552: Se1/2 LCP: I TERMREQ [TERMsent] id 9 len 4 *Mar 1 06:06:11.552: Se1/2 LCP: O TERMACK [TERMsent] id 9 len 4 *Mar 1 06:06:11.552: Se1/2 LCP: I TERMACK [TERMsent] id 3 len 4 *Mar 1 06:06:11.552: Se1/2 LCP: State is Closed *Mar 1 06:06:11.552: Se1/2 PPP: Phase is DOWN *Mar 1 06:06:13.563: Se1/2 LCP: I CONFREQ [Closed] id 10 len 14 *Mar 1 06:06:13.563: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:13.563: Se1/2 LCP: MagicNumber 0x14CE460C (0x050614CE460C) *Mar 1 06:06:13.563: Se1/2 LCP: Missed a Link-Up transition, starting PPP *Mar 1 06:06:13.563: Se1/2 PPP: Using default call direction *Mar 1 06:06:13.563: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:06:13.563: Se1/2 PPP: Session handle[79000002] Session id[2] *Mar 1 06:06:13.563: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:06:13.563: Se1/2 LCP: O CONFREQ [Closed] id 4 len 14 *Mar 1 06:06:13.567: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:13.567: Se1/2 LCP: MagicNumber 0x14B043C8 (0x050614B043C8) *Mar 1 06:06:13.567: Se1/2 LCP: O CONFACK [REQsent] id 10 len 14 *Mar 1 06:06:13.567: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:13.567: Se1/2 LCP: MagicNumber 0x14CE460C (0x050614CE460C) *Mar 1 06:06:13.575: Se1/2 LCP: I CONFACK [ACKsent] id 4 len 14 *Mar 1 06:06:13.575: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:13.575: Se1/2 LCP: MagicNumber 0x14B043C8 (0x050614B043C8) *Mar 1 06:06:13.575: Se1/2 LCP: State is Open *Mar 1 06:06:13.575: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:06:13.575: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:06:13.575: Se1/2 PAP: Using password from interface PAP *Mar 1 06:06:13.575: Se1/2 PAP: O AUTH-REQ id 2 len 13 from "R2" *Mar 1 06:06:13.579: Se1/2 PAP: I AUTH-REQ id 2 len 21 from "Two" *Mar 1 06:06:13.579: Se1/2 PAP: Authenticating peer Two *Mar 1 06:06:13.579: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:06:13.579: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:06:13.583: Se1/2 PAP: O AUTH-NAK id 2 len 26 msg is "Authentication failed" *Mar 1 06:06:13.583: Se1/2 PPP: Sending Acct Event[Down] id[5] *Mar 1 06:06:13.583: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:06:13.583: Se1/2 LCP: O TERMREQ [Open] id 5 len 4 *Mar 1 06:06:13.587: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:06:13.591: Se1/2 LCP: I TERMREQ [TERMsent] id 11 len 4 *Mar 1 06:06:13.591: Se1/2 LCP: O TERMACK [TERMsent] id 11 len 4 *Mar 1 06:06:15.579: Se1/2 LCP: I CONFREQ [TERMsent] id 12 len 14 *Mar 1 06:06:15.579: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:15.579: Se1/2 LCP: MagicNumber 0x14CE4DEC (0x050614CE4DEC) *Mar 1 06:06:15.579: Se1/2 LCP: Dropping packet, state is TERMsent *Mar 1 06:06:15.583: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 06:06:15.583: Se1/2 LCP: O TERMREQ [TERMsent] id 6 len 4 *Mar 1 06:06:15.587: Se1/2 LCP: I TERMACK [TERMsent] id 6 len 4 *Mar 1 06:06:15.587: Se1/2 LCP: State is Closed *Mar 1 06:06:15.587: Se1/2 PPP: Phase is DOWN *Mar 1 06:06:15.591: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:06:15.591: Se1/2 LCP: State is Listen *Mar 1 06:06:17.590: Se1/2 LCP: I CONFREQ [Listen] id 13 len 14 *Mar 1 06:06:17.594: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:17.594: Se1/2 LCP: MagicNumber 0x14CE4DEC (0x050614CE4DEC) *Mar 1 06:06:17.594: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:06:17.602: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:06:17.602: Se1/2 LCP: O CONFREQ [Listen] id 7 len 14 *Mar 1 06:06:17.602: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:17.602: Se1/2 LCP: MagicNumber 0x14B0538F (0x050614B0538F) *Mar 1 06:06:17.610: Se1/2 LCP: I CONFACK [REQsent] id 7 len 14 *Mar 1 06:06:17.610: Se1/2 LCP: AuthProto PAP (0x0304C023) R2(config-if)# R2(config-if)# *Mar 1 06:06:17.610: Se1/2 LCP: MagicNumber 0x14B0538F (0x050614B0538F) R2(config-if)# *Mar 1 06:06:19.609: Se1/2 LCP: I CONFREQ [ACKrcvd] id 14 len 14 *Mar 1 06:06:19.613: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:19.613: Se1/2 LCP: MagicNumber 0x14CE4DEC (0x050614CE4DEC) *Mar 1 06:06:19.613: Se1/2 LCP: O CONFACK [ACKrcvd] id 14 len 14 *Mar 1 06:06:19.613: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:19.613: Se1/2 LCP: MagicNumber 0x14CE4DEC (0x050614CE4DEC) *Mar 1 06:06:19.613: Se1/2 LCP: State is Open *Mar 1 06:06:19.613: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:06:19.613: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:06:19.617: Se1/2 PAP: Using password from interface PAP *Mar 1 06:06:19.617: Se1/2 PAP: O AUTH-REQ id 3 len 13 from "R2" *Mar 1 06:06:19.621: Se1/2 PAP: I AUTH-REQ id 3 len 21 from "Two" *Mar 1 06:06:19.625: Se1/2 PAP: Authenticating peer Two *Mar 1 06:06:19.625: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:06:19.625: Se1/2 PPP: Phase is AUTHENTICATING, Unaut R2(config-if)#henticated User *Mar 1 06:06:19.625: Se1/2 PAP: O AUTH-NAK id 3 len 26 msg is "Authentication failed" *Mar 1 06:06:19.629: Se1/2 PPP: Sending Acct Event[Down] id[6] *Mar 1 06:06:19.629: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:06:19.629: Se1/2 LCP: O TERMREQ [Open] id 8 len 4 *Mar 1 06:06:19.629: Se1/2 LCP: I TERMREQ [TERMsent] id 15 len 4 *Mar 1 06:06:19.633: Se1/2 LCP: O TERMACK [TERMsent] id 15 len 4 R2(config-if)# *Mar 1 06:06:21.629: Se1/2 LCP: I CONFREQ [TERMsent] id 16 len 14 *Mar 1 06:06:21.629: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:21.629: Se1/2 LCP: MagicNumber 0x14CE658F (0x050614CE658F) *Mar 1 06:06:21.629: Se1/2 LCP: Dropping packet, state is TERMsent *Mar 1 06:06:21.633: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 06:06:21.633: Se1/2 LCP: O TERMREQ [TERMsent] id 9 len 4 *Mar 1 06:06:21.637: Se1/2 LCP: I TERMACK [TERMsent] id 9 len 4 *Mar 1 06:06:21.637: Se1/2 LCP: State is Closed *Mar 1 06:06:21.637: Se1/2 PPP: Phase is DOWN *Mar 1 06:06:21.641: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:06:21.641: Se1/2 LCP: State is Listen R2(config-if)# *Mar 1 06:06:23.640: Se1/2 LCP: I CONFREQ [Listen] id 17 len 14 *Mar 1 06:06:23.644: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:23.644: Se1/2 LCP: MagicNumber 0x14CE658F (0x050614CE658F) *Mar 1 06:06:23.644: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:06:23.648: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:06:23.648: Se1/2 LCP: O CONFREQ [Listen] id 10 len 14 *Mar 1 06:06:23.648: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:23.648: Se1/2 LCP: MagicNumber 0x14B06B2E (0x050614B06B2E) *Mar 1 06:06:23.656: Se1/2 LCP: I CONFACK [REQsent] id 10 len 14 *Mar 1 06:06:23.656: Se1/2 LCP: AuthProto PAP (0x0304C023) R2(config-if)# *Mar 1 06:06:23.656: Se1/2 LCP: MagicNumber 0x14B06B2E (0x050614B06B2E) R2(config-if)# *Mar 1 06:06:25.655: Se1/2 LCP: I CONFREQ [ACKrcvd] id 18 len 14 *Mar 1 06:06:25.659: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:25.659: Se1/2 LCP: MagicNumber 0x14CE658F (0x050614CE658F) *Mar 1 06:06:25.659: Se1/2 LCP: O CONFACK [ACKrcvd] id 18 len 14 *Mar 1 06:06:25.659: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:25.659: Se1/2 LCP: MagicNumber 0x14CE658F (0x050614CE658F) *Mar 1 06:06:25.659: Se1/2 LCP: State is Open *Mar 1 06:06:25.659: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:06:25.659: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:06:25.663: Se1/2 PAP: Using password from interface PAP *Mar 1 06:06:25.663: Se1/2 PAP: O AUTH-REQ id 4 len 13 from "R2" *Mar 1 06:06:25.667: Se1/2 PAP: I AUTH-REQ id 4 len 21 from "Two" *Mar 1 06:06:25.671: Se1/2 PAP: Authenticating peer Two *Mar 1 06:06:25.671: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:06:25.671: Se1/2 PPP: Phase is AUTHENTICATING, Unaut R2(config-if)#henticated User *Mar 1 06:06:25.671: Se1/2 PAP: O AUTH-NAK id 4 len 26 msg is "Authentication failed" *Mar 1 06:06:25.675: Se1/2 PPP: Sending Acct Event[Down] id[7] *Mar 1 06:06:25.675: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:06:25.675: Se1/2 LCP: O TERMREQ [Open] id 11 len 4 *Mar 1 06:06:25.675: Se1/2 LCP: I TERMREQ [TERMsent] id 19 len 4 *Mar 1 06:06:25.679: Se1/2 LCP: O TERMACK [TERMsent] id 19 len 4 *Mar 1 06:06:25.683: Se1/2 LCP: I TERMACK [TERMsent] id 11 len 4 *Mar 1 06:06:25.683: Se1/2 LCP: State is Closed *Mar 1 06:06:25.683: Se1/2 PPP: Phase is DOWN *Mar 1 06:06:25.687: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:06:25.687: Se1/2 LCP: State is Listen R2(config-if)# *Mar 1 06:06:27.675: Se1/2 LCP: I CONFREQ [Listen] id 20 len 14 *Mar 1 06:06:27.675: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:27.675: Se1/2 LCP: MagicNumber 0x14CE7D2E (0x050614CE7D2E) *Mar 1 06:06:27.675: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:06:27.679: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:06:27.679: Se1/2 LCP: O CONFREQ [Listen] id 12 len 14 *Mar 1 06:06:27.679: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:27.679: Se1/2 LCP: MagicNumber 0x14B07AEE (0x050614B07AEE) *Mar 1 06:06:27.687: Se1/2 LCP: I CONFACK [REQsent] id 12 len 14 *Mar 1 06:06:27.687: Se1/2 LCP: AuthProto PAP (0x0304C023) R2(config-if)# *Mar 1 06:06:27.687: Se1/2 LCP: MagicNumber 0x14B07AEE (0x050614B07AEE) R2(config-if)# *Mar 1 06:06:29.686: Se1/2 LCP: I CONFREQ [ACKrcvd] id 21 len 14 *Mar 1 06:06:29.690: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:29.690: Se1/2 LCP: MagicNumber 0x14CE7D2E (0x050614CE7D2E) *Mar 1 06:06:29.690: Se1/2 LCP: O CONFACK [ACKrcvd] id 21 len 14 *Mar 1 06:06:29.690: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:29.690: Se1/2 LCP: MagicNumber 0x14CE7D2E (0x050614CE7D2E) *Mar 1 06:06:29.690: Se1/2 LCP: State is Open *Mar 1 06:06:29.690: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:06:29.690: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:06:29.694: Se1/2 PAP: Using password from interface PAP *Mar 1 06:06:29.694: Se1/2 PAP: O AUTH-REQ id 5 len 13 from "R2" *Mar 1 06:06:29.698: Se1/2 PAP: I AUTH-REQ id 5 len 21 from "Two" *Mar 1 06:06:29.702: Se1/2 PAP: Authenticating peer Two *Mar 1 06:06:29.702: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:06:29.702: Se1/2 PPP: Phase is AUTHENTICATING, Unaut R2(config-if)#henticated User *Mar 1 06:06:29.702: Se1/2 PAP: O AUTH-NAK id 5 len 26 msg is "Authentication failed" *Mar 1 06:06:29.706: Se1/2 PPP: Sending Acct Event[Down] id[8] *Mar 1 06:06:29.706: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:06:29.706: Se1/2 LCP: O TERMREQ [Open] id 13 len 4 *Mar 1 06:06:29.706: Se1/2 LCP: I TERMREQ [TERMsent] id 22 len 4 *Mar 1 06:06:29.710: Se1/2 LCP: O TERMACK [TERMsent] id 22 len 4 *Mar 1 06:06:29.714: Se1/2 LCP: I TERMACK [TERMsent] id 13 len 4 *Mar 1 06:06:29.714: Se1/2 LCP: State is Closed *Mar 1 06:06:29.714: Se1/2 PPP: Phase is DOWN *Mar 1 06:06:29.718: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:06:29.718: Se1/2 LCP: State is Listen R2(config-if)# *Mar 1 06:06:31.709: Se1/2 LCP: I CONFREQ [Listen] id 23 len 14 *Mar 1 06:06:31.709: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:31.709: Se1/2 LCP: MagicNumber 0x14CE8CF1 (0x050614CE8CF1) *Mar 1 06:06:31.709: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:06:31.713: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:06:31.713: Se1/2 LCP: O CONFREQ [Listen] id 14 len 14 *Mar 1 06:06:31.713: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:31.713: Se1/2 LCP: MagicNumber 0x14B08AB1 (0x050614B08AB1) *Mar 1 06:06:31.721: Se1/2 LCP: I CONFACK [REQsent] id 14 len 14 *Mar 1 06:06:31.721: Se1/2 LCP: AuthProto PAP (0x0304C023) R2(config-if)# *Mar 1 06:06:31.721: Se1/2 LCP: MagicNumber 0x14B08AB1 (0x050614B08AB1) R2(config-if)# *Mar 1 06:06:33.720: Se1/2 LCP: I CONFREQ [ACKrcvd] id 24 len 14 *Mar 1 06:06:33.724: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:33.724: Se1/2 LCP: MagicNumber 0x14CE8CF1 (0x050614CE8CF1) *Mar 1 06:06:33.724: Se1/2 LCP: O CONFACK [ACKrcvd] id 24 len 14 *Mar 1 06:06:33.724: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:33.724: Se1/2 LCP: MagicNumber 0x14CE8CF1 (0x050614CE8CF1) *Mar 1 06:06:33.724: Se1/2 LCP: State is Open *Mar 1 06:06:33.724: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:06:33.724: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:06:33.728: Se1/2 PAP: Using password from interface PAP *Mar 1 06:06:33.728: Se1/2 PAP: O AUTH-REQ id 6 len 13 from "R2" *Mar 1 06:06:33.732: Se1/2 PAP: I AUTH-REQ id 6 len 21 from "Two" *Mar 1 06:06:33.736: Se1/2 PAP: Authenticating peer Two *Mar 1 06:06:33.736: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:06:33.736: Se1/2 PPP: Phase is AUTHENTICATING, Unaut R2(config-if)#henticated User *Mar 1 06:06:33.736: Se1/2 PAP: O AUTH-NAK id 6 len 26 msg is "Authentication failed" *Mar 1 06:06:33.740: Se1/2 PPP: Sending Acct Event[Down] id[9] *Mar 1 06:06:33.740: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:06:33.740: Se1/2 LCP: O TERMREQ [Open] id 15 len 4 *Mar 1 06:06:33.740: Se1/2 LCP: I TERMREQ [TERMsent] id 25 len 4 *Mar 1 06:06:33.744: Se1/2 LCP: O TERMACK [TERMsent] id 25 len 4 R2(config-if)# *Mar 1 06:06:35.740: Se1/2 LCP: I CONFREQ [TERMsent] id 26 len 14 *Mar 1 06:06:35.740: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:35.740: Se1/2 LCP: MagicNumber 0x14CE9CB1 (0x050614CE9CB1) *Mar 1 06:06:35.740: Se1/2 LCP: Dropping packet, state is TERMsent *Mar 1 06:06:35.744: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 06:06:35.744: Se1/2 LCP: O TERMREQ [TERMsent] id 16 len 4 *Mar 1 06:06:35.764: Se1/2 LCP: I TERMACK [TERMsent] id 16 len 4 *Mar 1 06:06:35.764: Se1/2 LCP: State is Closed *Mar 1 06:06:35.764: Se1/2 PPP: Phase is DOWN *Mar 1 06:06:35.764: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:06:35.764: Se1/2 LCP: State is Listen R2(config-if)# *Mar 1 06:06:37.751: Se1/2 LCP: I CONFREQ [Listen] id 27 len 14 *Mar 1 06:06:37.755: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:37.755: Se1/2 LCP: MagicNumber 0x14CE9CB1 (0x050614CE9CB1) *Mar 1 06:06:37.755: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:06:37.759: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:06:37.759: Se1/2 LCP: O CONFREQ [Listen] id 17 len 14 *Mar 1 06:06:37.759: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:37.759: Se1/2 LCP: MagicNumber 0x14B0A250 (0x050614B0A250) *Mar 1 06:06:37.767: Se1/2 LCP: I CONFACK [REQsent] id 17 len 14 *Mar 1 06:06:37.767: Se1/2 LCP: AuthProto PAP (0x0304C023) R2(config-if)# *Mar 1 06:06:37.767: Se1/2 LCP: MagicNumber 0x14B0A250 (0x050614B0A250) R2(config-if)# *Mar 1 06:06:39.766: Se1/2 LCP: I CONFREQ [ACKrcvd] id 28 len 14 *Mar 1 06:06:39.770: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:39.770: Se1/2 LCP: MagicNumber 0x14CE9CB1 (0x050614CE9CB1) *Mar 1 06:06:39.770: Se1/2 LCP: O CONFACK [ACKrcvd] id 28 len 14 *Mar 1 06:06:39.770: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:39.770: Se1/2 LCP: MagicNumber 0x14CE9CB1 (0x050614CE9CB1) *Mar 1 06:06:39.770: Se1/2 LCP: State is Open *Mar 1 06:06:39.770: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:06:39.770: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:06:39.774: Se1/2 PAP: Using password from interface PAP *Mar 1 06:06:39.774: Se1/2 PAP: O AUTH-REQ id 7 len 13 from "R2" *Mar 1 06:06:39.778: Se1/2 PAP: I AUTH-REQ id 7 len 21 from "Two" *Mar 1 06:06:39.782: Se1/2 PAP: Authenticating peer Two *Mar 1 06:06:39.782: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:06:39.782: Se1/2 PPP: Phase is AUTHENTICATING, Unaut R2(config-if)#henticated User *Mar 1 06:06:39.782: Se1/2 PAP: O AUTH-NAK id 7 len 26 msg is "Authentication failed" *Mar 1 06:06:39.786: Se1/2 PPP: Sending Acct Event[Down] id[A] *Mar 1 06:06:39.786: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:06:39.786: Se1/2 LCP: O TERMREQ [Open] id 18 len 4 *Mar 1 06:06:39.786: Se1/2 LCP: I TERMREQ [TERMsent] id 29 len 4 *Mar 1 06:06:39.790: Se1/2 LCP: O TERMACK [TERMsent] id 29 len 4 *Mar 1 06:06:39.794: Se1/2 LCP: I TERMACK [TERMsent] id 18 len 4 *Mar 1 06:06:39.794: Se1/2 LCP: State is Closed *Mar 1 06:06:39.794: Se1/2 PPP: Phase is DOWN *Mar 1 06:06:39.798: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:06:39.798: Se1/2 LCP: State is Listen R2(config-if)# *Mar 1 06:06:41.786: Se1/2 LCP: I CONFREQ [Listen] id 30 len 14 *Mar 1 06:06:41.786: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:41.786: Se1/2 LCP: MagicNumber 0x14CEB450 (0x050614CEB450) *Mar 1 06:06:41.786: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:06:41.794: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:06:41.794: Se1/2 LCP: O CONFREQ [Listen] id 19 len 14 *Mar 1 06:06:41.794: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:41.794: Se1/2 LCP: MagicNumber 0x14B0B214 (0x050614B0B214) *Mar 1 06:06:41.802: Se1/2 LCP: I CONFACK [REQsent] id 19 len 14 *Mar 1 06:06:41.802: Se1/2 LCP: AuthProto PAP (0x0304C023) R2(config-if)# *Mar 1 06:06:41.802: Se1/2 LCP: MagicNumber 0x14B0B214 (0x050614B0B214) R2(config-if)# *Mar 1 06:06:43.805: Se1/2 LCP: I CONFREQ [ACKrcvd] id 31 len 14 *Mar 1 06:06:43.805: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:43.805: Se1/2 LCP: MagicNumber 0x14CEB450 (0x050614CEB450) *Mar 1 06:06:43.805: Se1/2 LCP: O CONFACK [ACKrcvd] id 31 len 14 *Mar 1 06:06:43.805: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:43.805: Se1/2 LCP: MagicNumber 0x14CEB450 (0x050614CEB450) *Mar 1 06:06:43.805: Se1/2 LCP: State is Open *Mar 1 06:06:43.805: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:06:43.805: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:06:43.809: Se1/2 PAP: Using password from interface PAP *Mar 1 06:06:43.809: Se1/2 PAP: O AUTH-REQ id 8 len 13 from "R2" *Mar 1 06:06:43.813: Se1/2 PAP: I AUTH-REQ id 8 len 21 from "Two" *Mar 1 06:06:43.817: Se1/2 PAP: Authenticating peer Two *Mar 1 06:06:43.817: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:06:43.817: Se1/2 PPP: Phase is AUTHENTICATING, Unaut R2(config-if)#henticated User *Mar 1 06:06:43.817: Se1/2 PAP: O AUTH-NAK id 8 len 26 msg is "Authentication failed" *Mar 1 06:06:43.821: Se1/2 PPP: Sending Acct Event[Down] id[B] *Mar 1 06:06:43.821: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:06:43.821: Se1/2 LCP: O TERMREQ [Open] id 20 len 4 *Mar 1 06:06:43.821: Se1/2 LCP: I TERMREQ [TERMsent] id 32 len 4 *Mar 1 06:06:43.825: Se1/2 LCP: O TERMACK [TERMsent] id 32 len 4 *Mar 1 06:06:43.829: Se1/2 LCP: I TERMACK [TERMsent] id 20 len 4 *Mar 1 06:06:43.829: Se1/2 LCP: State is Closed *Mar 1 06:06:43.829: Se1/2 PPP: Phase is DOWN *Mar 1 06:06:43.833: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:06:43.833: Se1/2 LCP: State is Listen R2(config-if)# *Mar 1 06:06:45.820: Se1/2 LCP: I CONFREQ [Listen] id 33 len 14 *Mar 1 06:06:45.820: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:45.820: Se1/2 LCP: MagicNumber 0x14CEC413 (0x050614CEC413) *Mar 1 06:06:45.820: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:06:45.824: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:06:45.824: Se1/2 LCP: O CONFREQ [Listen] id 21 len 14 *Mar 1 06:06:45.824: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:45.824: Se1/2 LCP: MagicNumber 0x14B0C1D4 (0x050614B0C1D4) *Mar 1 06:06:45.832: Se1/2 LCP: I CONFACK [REQsent] id 21 len 14 *Mar 1 06:06:45.832: Se1/2 LCP: AuthProto PAP (0x0304C023) R2(config-if)# *Mar 1 06:06:45.832: Se1/2 LCP: MagicNumber 0x14B0C1D4 (0x050614B0C1D4) R2(config-if)#do *Mar 1 06:06:47.836: Se1/2 LCP: I CONFREQ [ACKrcvd] id 34 len 14 *Mar 1 06:06:47.836: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:47.836: Se1/2 LCP: MagicNumber 0x14CEC413 (0x050614CEC413) *Mar 1 06:06:47.836: Se1/2 LCP: O CONFACK [ACKrcvd] id 34 len 14 *Mar 1 06:06:47.836: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:06:47.836: Se1/2 LCP: MagicNumber 0x14CEC413 (0x050614CEC413) *Mar 1 06:06:47.836: Se1/2 LCP: State is Open *Mar 1 06:06:47.836: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:06:47.836: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:06:47.840: Se1/2 PAP: Using password from interface PAP *Mar 1 06:06:47.840: Se1/2 PAP: O AUTH-REQ id 9 len 13 from "R2" *Mar 1 06:06:47.844: Se1/2 PAP: I AUTH-REQ id 9 len 21 from "Two" *Mar 1 06:06:47.848: Se1/2 PAP: Authenticating peer Two *Mar 1 06:06:47.848: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:06:47.848: Se1/2 PPP: Phase is AUTHENTICATING, Unautu R2(config-if)henticated User *Mar 1 06:06:47.848: Se1/2 PAP: O AUTH-NAK id 9 len 26 msg is "Authentication failed" *Mar 1 06:06:47.852: Se1/2 PPP: Sending Acct Event[Down] id[C] *Mar 1 06:06:47.852: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:06:47.852: Se1/2 LCP: O TERMREQ [Open] id 22 len 4 *Mar 1 06:06:47.852: Se1/2 LCP: I TERMREQ [TERMsent] id 35 len 4 *Mar 1 06:06:47.856: Se1/2 LCP: O TERMACK [TERMsent] id 35 len 4#do u all All possible debugging has been turned off R2(config-if)#no    shut R2(config-if)#shutdo u allno shut  *Mar 1 06:06:55.901: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down R2(config-if)#no shutppp pap sent-username R2 pass cisco             One pass For-The-Money R2(config-if)#exut ^ % Invalid input detected at '^' marker. R2(config-if)#exit R2(config)#user Two o pass For-The-Show R2(config)#int s 1/2 R2(config-if)#do sh    deb ppp ne PPP protocol negotiation debugging is on R2(config-if)#no shut R2(config-if)# *Mar 1 06:07:26.142: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:07:26.166: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:07:26.190: Se1/2 PPP: Outbound cdp packet dropped R2(config-if)# *Mar 1 06:07:28.118: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 06:07:28.118: Se1/2 PPP: Using default call direction *Mar 1 06:07:28.118: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:07:28.118: Se1/2 PPP: Session handle[1600000C] Session id[12] *Mar 1 06:07:28.118: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:07:28.118: Se1/2 LCP: O CONFREQ [Closed] id 26 len 14 *Mar 1 06:07:28.118: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:07:28.122: Se1/2 LCP: MagicNumber 0x14B1670B (0x050614B1670B) *Mar 1 06:07:28.126: Se1/2 LCP: I CONFREQ [REQsent] id 40 len 14 *Mar 1 06:07:28.126: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:07:28.126: Se1/2 LCP: MagicNumber 0x14CF6957 (0x050614CF6957) *Mar 1 06:07:28.126: Se1/2 LCP: O CONFACK [REQsent] id 40 len 14 *Mar 1 06:07:28.126: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:07:28.130: Se1/2 LCP: MagicNumber 0x14CF6957 (0x050614CF6957) *Mar 1 06:07: R2(config-if)#28.130: Se1/2 LCP: I CONFACK [ACKsent] id 26 len 14 *Mar 1 06:07:28.130: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:07:28.130: Se1/2 LCP: MagicNumber 0x14B1670B (0x050614B1670B) *Mar 1 06:07:28.130: Se1/2 LCP: State is Open *Mar 1 06:07:28.130: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:07:28.130: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:07:28.130: Se1/2 PAP: Using password from interface PAP *Mar 1 06:07:28.130: Se1/2 PAP: O AUTH-REQ id 11 len 22 from "One" *Mar 1 06:07:28.138: Se1/2 PAP: I AUTH-REQ id 11 len 21 from "Two" *Mar 1 06:07:28.138: Se1/2 PAP: Authenticating peer Two *Mar 1 06:07:28.138: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:07:28.138: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:07:28.142: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:07:28.142: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 06:07:28.146: Se1/2 PAP: O AUTH-ACK id 11 len 5 *Mar 1 06:07:28.146: Se1/2 PAP: I AUTH-ACK id 11 len 5 *Mar 1 06:07:28.146: Se1/2 PPP: Phase is UP *Mar 1 06:07:28.146: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 06:07:28.150: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:07:28.150: Se1/2 PPP: Process pending ncp packets *Mar 1 06:07:28.150: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 06:07:28.154: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 06:07:28.154: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:07:28.154: Se1/2 AAA/AUTHOR/IPCP: Start. Her address 180.40.7.3, we want 0.0.0.0 *Mar 1 06:07:28.154: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 06:07:28.158: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 06:07:28.158: Se1/2 AAA/AUTHOR/IPCP: Reject 180.40.7.3, using 0.0.0.0 *Mar 1 06:07:28.158: Se1/2 AAA/AUTHOR/IPCP: Done. Her address 180.40.7.3, we want 0.0.0.0 *Mar 1 06:07:28.158: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 06:07:28.162: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:07:28.162: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 06:07:28.162: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:07:28.162: Se1/2 IPCP: State is Open *Mar 1 06:07:28.162: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 06:07:28.162: Se1/2 CDPCP: State is Open *Mar 1 06:07:28.166: Se1/2 IPCP: Install route to 180.40.7.3 *Mar 1 06:07:28.170: Se1/2 IPCP: Add link info for cef entry 180.40.7.3 *Mar 1 06:07:29.147: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2(config-if)# R2(config-if)# R2(config-if)# R2(config-if)# R2(config-if)#ppp authen ppp  ap op R2(config-if)#^Z R2# *Mar 1 06:07:48.154: %SYS-5-CONFIG_I: Configured from console by console R2# R2# R2# R2# R2#sh run | b user username Two password 0 For-The-Show ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 duplex auto speed auto --More--  ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp authentication pap optional ppp pap sent-username One password 0 For-The-Money ! interface Serial1/3 --More-- RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-if)#^Z R3#sh run *Mar 1 06:13:26.621: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b user username One password 0 For-The-Money ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto --More--  ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 broadcast no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show ! interface Serial1/3 no ip address --More--   R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#shut R3(config-if)#do *Mar 1 06:14:03.406: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 06:14:04.407: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 179 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp shutdown ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show end R3(config-if)#no ppp authentication pap optional R3(config-if)#n  o ppp pap sent-username Two password 0 For-The-Show R3(config-if)#ppp authen cha R3(config-if)#ppp authen chap op R3(config-if)#ppp authen chap optional R3(config-if)#ppp cha R3(config-if)#ppp chap ? hostname Set alternate CHAP hostname password Set default CHAP password refuse Refuse to authenticate using CHAP wait Wait for caller to authenticate first R3(config-if)#ppp chap host Two ? R3(config-if)#ppp chap host Two   R3(config-if)#ppp chap pass R3(config-if)#ppp chap password For-The-Show R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Ma  no ip address --More--   R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 12 ^ % Invalid input detected at '^' marker. R2(config)#int s 12/2 R2(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 188 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp authentication pap optional ppp pap sent-username One password 0 For-The-Money end R2(config-if)#no ppp authentication pap optional R2(config-if)#no ppp pap sent-username One password 0 For-The-Money R2(config-if)#ppp authen cha op R2(config-if)#ppp ch host One R2(config-if)#ppp cha pass For-The-Money R2(config-if)# R2(config-if)#^Z R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do deb ppp ne PPP protocol negotiation debugging is on R3(config-if)#no shut R3(config-if)# *Mar 1 06:15:37.275: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:15:37.300: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:15:37.324: Se1/2 PPP: Outbound cdp packet dropped R3(config-if)# *Mar 1 06:15:39.255: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 06:15:39.255: Se1/2 PPP: Using default call direction *Mar 1 06:15:39.255: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:15:39.255: Se1/2 PPP: Session handle[C500000D] Session id[13] *Mar 1 06:15:39.255: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:15:39.255: Se1/2 LCP: O CONFREQ [Closed] id 41 len 15 *Mar 1 06:15:39.255: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:39.259: Se1/2 LCP: MagicNumber 0x14D70732 (0x050614D70732) *Mar 1 06:15:39.259: Se1/2 LCP: I CONFREQ [REQsent] id 27 len 15 *Mar 1 06:15:39.263: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:39.263: Se1/2 LCP: MagicNumber 0x14B904EA (0x050614B904EA) *Mar 1 06:15:39.263: Se1/2 LCP: O CONFACK [REQsent] id 27 len 15 *Mar 1 06:15:39.263: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:39.263: Se1/2 LCP: MagicNumber 0x14B904EA (0x050614B904EA) *Mar R3(config-if)# 1 06:15:39.267: Se1/2 LCP: I CONFACK [ACKsent] id 41 len 15 *Mar 1 06:15:39.271: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:39.271: Se1/2 LCP: MagicNumber 0x14D70732 (0x050614D70732) *Mar 1 06:15:39.271: Se1/2 LCP: State is Open *Mar 1 06:15:39.271: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:15:39.271: Se1/2 CHAP: O CHALLENGE id 1 len 24 from "Two" *Mar 1 06:15:39.275: Se1/2 CHAP: I CHALLENGE id 1 len 24 from "One" *Mar 1 06:15:39.279: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:15:39.279: Se1/2 CHAP: Using password from AAA *Mar 1 06:15:39.279: Se1/2 CHAP: O RESPONSE id 1 len 24 from "Two" *Mar 1 06:15:39.287: Se1/2 CHAP: I RESPONSE id 1 len 24 from "One" *Mar 1 06:15:39.287: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:15:39.287: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:15:39.291: Se1/2 CHAP: O FAILURE id 1 len 25 msg is "Authentication failed" *Mar 1 06:15:39.291: Se1/2 PPP: Sending Acct Event[Down] id[F] *Mar 1 06:15:39.291: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:15:39.291: Se1/2 LCP: O TERMREQ [Open] id 42 len 4 *Mar 1 06:15:39.295: Se1/2 CHAP: LCP not open, discarding packet *Mar 1 06:15:39.295: Se1/2 LCP: I TERMREQ [TERMsent] id 28 len 4 *Mar 1 06:15:39.295: Se1/2 LCP: O TERMACK [TERMsent] id 28 len 4 *Mar 1 06:15:39.299: Se1/2 LCP: I TERMACK [TERMsent] id 42 len 4 *Mar 1 06:15:39.299: Se1/2 LCP: State is Closed *Mar 1 06:15:39.299: Se1/2 PPP: Phase is DOWN *Mar 1 06:15:39.303: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:15:39.303: Se1/2 LCP: State is Listen *Mar 1 06:15:41.306: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:15:41.306: Se1/2 LCP: O CONFREQ [Listen] id 43 len 15 *Mar 1 06:15:41.306: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:41.306: Se1/2 LCP: MagicNumber 0x14D70F37 (0x050614D70F37) *Mar 1 06:15:41.318: Se1/2 LCP: I CONFREQ [REQsent] id 29 len 15 *Mar 1 06:15:41.318: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:41.322: Se1/2 LCP: MagicNumber 0x14B90CF8 (0x050614B90CF8) *Mar 1 06:15:41.322: Se1/2 LCP: O CONFACK [REQsent] id 29 len 15 *Mar 1 06:15:41.322: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:41.322: Se1/2 LCP: MagicNumber 0x14B90CF8 (0x050614B90CF8) *Mar 1 06:15:41.322: Se1/2 LCP: I CONFACK [ACKsent] id 43 len 15 *Mar 1 06:15:41.322: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:41.322: Se1/2 LCP: MagicNumber 0x14D70F37 (0x050614D70F37) *Mar 1 06:15:41.326: Se1/2 LCP: State is Open *Mar 1 06:15:41.326: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:15:41.326: Se1/2 CHAP: O CHALLENGE id 2 len 24 from "Two" *Mar 1 06:15:41.334: Se1/2 CHAP: I CHALLENGE id 2 len 24 from "One" *Mar 1 06:15:41.338: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:15:41.338: Se1/2 CHAP: Using password from AAA *Mar 1 06:15:41.338: Se1/2 CHAP: O RESPONSE id 2 len 24 from "Two" *Mar 1 06:15:41.342: Se1/2 CHAP: I RESPONSE id 2 len 24 from "One" *Mar 1 06:15:41.342: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:15:41.342: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:15:41.346: Se1/2 CHAP: O FAILURE id 2 len 25 msg is "Authentication failed" *Mar 1 06:15:41.346: Se1/2 PPP: Sending Acct Event[Down] id[10] *Mar 1 06:15:41.346: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:15:41.346: Se1/2 LCP: O TERMREQ [Open] id 44 len 4 *Mar 1 06:15:41.354: Se1/2 CHAP: LCP not open, discarding packet *Mar 1 06:15:41.354: Se1/2 LCP: I TERMREQ [TERMsent] id 30 len 4 *Mar 1 06:15:41.354: Se1/2 LCP: O TERMACK [TERMsent] id 30 len 4 *Mar 1 06:15:41.358: Se1/2 LCP: I TERMACK [TERMsent] id 44 len 4 *Mar 1 06:15:41.358: Se1/2 LCP: State is Closed *Mar 1 06:15:41.358: Se1/2 PPP: Phase is DOWN *Mar 1 06:15:41.358: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:15:41.358: Se1/2 LCP: State is Listen *Mar 1 06:15:43.353: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:15:43.353: Se1/2 LCP: O CONFREQ [Listen] id 45 len 15 *Mar 1 06:15:43.353: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:43.353: Se1/2 LCP: MagicNumber 0x14D71738 (0x050614D71738) *Mar 1 06:15:43.365: Se1/2 LCP: I CONFREQ [REQsent] id 31 len 15 *Mar 1 06:15:43.365: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:43.369: Se1/2 LCP: MagicNumber 0x14B914F8 (0x050614B914F8) *Mar 1 06:15:43.369: Se1/2 LCP: O CONFACK [REQsent] id 31 len 15 *Mar 1 06:15:43.369: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:43.369: Se1/2 LCP: MagicNumber 0x14B914F8 (0x050614B914F8) *Mar 1 06:15:45.369: Se1/2 LCP: TIMEout: State ACKsent *Mar 1 06:15:45.369: Se1/2 LCP: O CONFREQ [ACKsent] id 46 len 15 *Mar 1 06:15:45.369: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:45.369: Se1/2 LCP: MagicNumber 0x14D71738 (0x050614D71738) *Mar 1 06:15:45.381: Se1/2 LCP: I CONFACK [ACKsent] id 46 len 15 *Mar 1 06:15:45.381: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:45.381: Se1/2 LCP: MagicNumber 0x14D71738 (0x050614D71738) *Mar 1 06:15:45.381: Se1/2 LCP: State is Open *Mar 1 06:15:45.381: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:15:45.381: Se1/2 CHAP: O CHALLENGE id 3 len 24 from "Two" *Mar 1 06:15:45.385: Se1/2 CHAP: I CHALLENGE id 3 len 24 from "One" *Mar 1 06:15:45.385: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:15:45.389: Se1/2 CHAP: Using password from AAA *Mar 1 06:15:45.389: Se1/2 CHAP: O RESPONSE id 3 len 24 from "Two" *Mar 1 06:15:45.397: Se1/2 CHAP: I RESPONSE id 3 len 24 from "One" *Mar 1 06:15:45.397: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:15:45.397: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:15:45.401: Se1/2 CHAP: O FAILURE id 3 len 25 msg is "Authentication failed" *Mar 1 06:15:45.401: Se1/2 PPP: Sending Acct Event[Down] id[11] *Mar 1 06:15:45.405: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:15:45.405: Se1/2 LCP: O TERMREQ [Open] id 47 len 4 *Mar 1 06:15:45.405: Se1/2 LCP: I TERMREQ [TERMsent] id 32 len 4 *Mar 1 06:15:45.405: Se1/2 LCP: O TERMACK [TERMsent] id 32 len 4 *Mar 1 06:15:45.413: Se1/2 LCP: I TERMACK [TERMsent] id 47 len 4 *Mar 1 06:15:45.413: Se1/2 LCP: State is Closed *Mar 1 06:15:45.413: Se1/2 PPP: Phase is DOWN *Mar 1 06:15:45.417: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:15:45.417: Se1/2 LCP: State is Listen *Mar 1 06:15:47.400: Se1/2 LCP: I CONFREQ [Listen] id 33 len 15 *Mar 1 06:15:47.400: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:47.400: Se1/2 LCP: MagicNumber 0x14B924BD (0x050614B924BD) *Mar 1 06:15:47.400: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:15:47.420: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:15:47.420: Se1/2 LCP: O CONFREQ [Listen] id 48 len 15 *Mar 1 06:15:47.420: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:47.420: Se1/2 LCP: MagicNumber 0x14D7271C (0x050614D7271C) *Mar 1 06:15:47.432: Se1/2 LCP: I CONFACK [REQsent] id 48 len 15 *Mar 1 06:15:47.432: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:47.432: Se1/2 LCP: MagicNumber 0x14D7271C (0x050614D7271C) R3(config-if)# R3(config-if)# *Mar 1 06:15:49.415: Se1/2 LCP: I CONFREQ [ACKrcvd] id 34 len 15 *Mar 1 06:15:49.415: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:49.415: Se1/2 LCP: MagicNumber 0x14B924BD (0x050614B924BD) *Mar 1 06:15:49.415: Se1/2 LCP: O CONFACK [ACKrcvd] id 34 len 15 *Mar 1 06:15:49.415: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:49.415: Se1/2 LCP: MagicNumber 0x14B924BD (0x050614B924BD) *Mar 1 06:15:49.419: Se1/2 LCP: State is Open *Mar 1 06:15:49.419: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:15:49.419: Se1/2 CHAP: O CHALLENGE id 4 len 24 from "Two" *Mar 1 06:15:49.427: Se1/2 CHAP: I CHALLENGE id 4 len 24 from "One" *Mar 1 06:15:49.431: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:15:49.431: Se1/2 CHAP: Using password from AAA *Mar 1 06:15:49.431: Se1/2 CHAP: O RESPONSE id 4 len 24 from "Two" *Mar 1 06:15:49.435: Se1/2 CHAP: I RESPONSE id 4 len 24 from "One" *Mar 1 06:15:49.435: Se1/2 PPP: Phase is FORWARDING, R3(config-if)# Attempting Forward *Mar 1 06:15:49.435: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:15:49.439: Se1/2 CHAP: O FAILURE id 4 len 25 msg is "Authentication failed" *Mar 1 06:15:49.439: Se1/2 PPP: Sending Acct Event[Down] id[12] *Mar 1 06:15:49.439: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:15:49.443: Se1/2 LCP: O TERMREQ [Open] id 49 len 4 *Mar 1 06:15:49.447: Se1/2 CHAP: LCP not open, discarding packet *Mar 1 06:15:49.451: Se1/2 LCP: I TERMREQ [TERMsent] id 35 len 4 *Mar 1 06:15:49.451: Se1/2 LCP: O TERMACK [TERMsent] id 35 len 4 *Mar 1 06:15:49.451: Se1/2 LCP: I TERMACK [TERMsent] id 49 len 4 *Mar 1 06:15:49.451: Se1/2 LCP: State is Closed *Mar 1 06:15:49.451: Se1/2 PPP: Phase is DOWN *Mar 1 06:15:49.455: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:15:49.455: Se1/2 LCP: State is Listen R3(config-if)# *Mar 1 06:15:51.451: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:15:51.451: Se1/2 LCP: O CONFREQ [Listen] id 50 len 15 *Mar 1 06:15:51.451: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:51.451: Se1/2 LCP: MagicNumber 0x14D736DC (0x050614D736DC) *Mar 1 06:15:51.463: Se1/2 LCP: I CONFREQ [REQsent] id 36 len 15 *Mar 1 06:15:51.467: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:51.467: Se1/2 LCP: MagicNumber 0x14B9349C (0x050614B9349C) *Mar 1 06:15:51.467: Se1/2 LCP: O CONFACK [REQsent] id 36 len 15 *Mar 1 06:15:51.467: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:51.467: Se1/2 LCP: MagicNumber 0x14B9349C (0x050614B9349C) R3(config-if)# *Mar 1 06:15:53.466: Se1/2 LCP: TIMEout: State ACKsent *Mar 1 06:15:53.466: Se1/2 LCP: O CONFREQ [ACKsent] id 51 len 15 *Mar 1 06:15:53.466: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:53.466: Se1/2 LCP: MagicNumber 0x14D736DC (0x050614D736DC) *Mar 1 06:15:53.482: Se1/2 LCP: I CONFACK [ACKsent] id 51 len 15 *Mar 1 06:15:53.482: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:53.482: Se1/2 LCP: MagicNumber 0x14D736DC (0x050614D736DC) *Mar 1 06:15:53.482: Se1/2 LCP: State is Open *Mar 1 06:15:53.482: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:15:53.482: Se1/2 CHAP: O CHALLENGE id 5 len 24 from "Two" *Mar 1 06:15:53.486: Se1/2 CHAP: I CHALLENGE id 5 len 24 from "One" *Mar 1 06:15:53.486: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:15:53.486: Se1/2 CHAP: Using password from AAA *Mar 1 06:15:53.486: Se1/2 CHAP: O RESPONSE id 5 len 24 from "Two" *Mar 1 06:15:53.502: Se1/2 CHAP: I RESPONSE id 5 len 24 from "On R3(config-if)#e" *Mar 1 06:15:53.502: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:15:53.506: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:15:53.506: Se1/2 CHAP: O FAILURE id 5 len 25 msg is "Authentication failed" *Mar 1 06:15:53.510: Se1/2 PPP: Sending Acct Event[Down] id[13] *Mar 1 06:15:53.510: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:15:53.510: Se1/2 LCP: O TERMREQ [Open] id 52 len 4 *Mar 1 06:15:53.514: Se1/2 LCP: I TERMREQ [TERMsent] id 37 len 4 *Mar 1 06:15:53.514: Se1/2 LCP: O TERMACK [TERMsent] id 37 len 4 *Mar 1 06:15:53.518: Se1/2 LCP: I TERMACK [TERMsent] id 52 len 4 *Mar 1 06:15:53.518: Se1/2 LCP: State is Closed *Mar 1 06:15:53.518: Se1/2 PPP: Phase is DOWN *Mar 1 06:15:53.522: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:15:53.522: Se1/2 LCP: State is Listen R3(config-if)# *Mar 1 06:15:55.513: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:15:55.513: Se1/2 LCP: O CONFREQ [Listen] id 53 len 15 *Mar 1 06:15:55.513: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:55.513: Se1/2 LCP: MagicNumber 0x14D746BD (0x050614D746BD) *Mar 1 06:15:55.533: Se1/2 LCP: I CONFREQ [REQsent] id 38 len 15 *Mar 1 06:15:55.533: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:55.533: Se1/2 LCP: MagicNumber 0x14B94481 (0x050614B94481) *Mar 1 06:15:55.533: Se1/2 LCP: O CONFACK [REQsent] id 38 len 15 *Mar 1 06:15:55.533: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:55.533: Se1/2 LCP: MagicNumber 0x14B94481 (0x050614B94481) R3(config-if)# *Mar 1 06:15:57.529: Se1/2 LCP: TIMEout: State ACKsent *Mar 1 06:15:57.529: Se1/2 LCP: O CONFREQ [ACKsent] id 54 len 15 *Mar 1 06:15:57.529: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:57.529: Se1/2 LCP: MagicNumber 0x14D746BD (0x050614D746BD) *Mar 1 06:15:57.585: Se1/2 LCP: I CONFACK [ACKsent] id 54 len 15 *Mar 1 06:15:57.585: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:57.585: Se1/2 LCP: MagicNumber 0x14D746BD (0x050614D746BD) *Mar 1 06:15:57.585: Se1/2 LCP: State is Open *Mar 1 06:15:57.585: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:15:57.585: Se1/2 CHAP: O CHALLENGE id 6 len 24 from "Two" *Mar 1 06:15:57.589: Se1/2 CHAP: I CHALLENGE id 6 len 24 from "One" *Mar 1 06:15:57.589: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:15:57.593: Se1/2 CHAP: Using password from AAA *Mar 1 06:15:57.593: Se1/2 CHAP: O RESPONSE id 6 len 24 from "Two" *Mar 1 06:15:57.601: Se1/2 CHAP: I RESPONSE id 6 len 24 from "On R3(config-if)#e" *Mar 1 06:15:57.601: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:15:57.601: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:15:57.605: Se1/2 CHAP: O FAILURE id 6 len 25 msg is "Authentication failed" *Mar 1 06:15:57.605: Se1/2 PPP: Sending Acct Event[Down] id[14] *Mar 1 06:15:57.609: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:15:57.609: Se1/2 LCP: O TERMREQ [Open] id 55 len 4 *Mar 1 06:15:57.609: Se1/2 LCP: I TERMREQ [TERMsent] id 39 len 4 *Mar 1 06:15:57.609: Se1/2 LCP: O TERMACK [TERMsent] id 39 len 4 *Mar 1 06:15:57.617: Se1/2 LCP: I TERMACK [TERMsent] id 55 len 4 *Mar 1 06:15:57.617: Se1/2 LCP: State is Closed *Mar 1 06:15:57.617: Se1/2 PPP: Phase is DOWN *Mar 1 06:15:57.617: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:15:57.617: Se1/2 LCP: State is Listen R3(config-if)# *Mar 1 06:15:59.612: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:15:59.612: Se1/2 LCP: O CONFREQ [Listen] id 56 len 15 *Mar 1 06:15:59.612: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:59.612: Se1/2 LCP: MagicNumber 0x14D756C0 (0x050614D756C0) *Mar 1 06:15:59.624: Se1/2 LCP: I CONFREQ [REQsent] id 40 len 15 *Mar 1 06:15:59.624: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:59.624: Se1/2 LCP: MagicNumber 0x14B95481 (0x050614B95481) *Mar 1 06:15:59.628: Se1/2 LCP: O CONFACK [REQsent] id 40 len 15 *Mar 1 06:15:59.628: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:15:59.628: Se1/2 LCP: MagicNumber 0x14B95481 (0x050614B95481) R3(config-if)# *Mar 1 06:16:01.627: Se1/2 LCP: TIMEout: State ACKsent *Mar 1 06:16:01.627: Se1/2 LCP: O CONFREQ [ACKsent] id 57 len 15 *Mar 1 06:16:01.627: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:01.627: Se1/2 LCP: MagicNumber 0x14D756C0 (0x050614D756C0) *Mar 1 06:16:01.639: Se1/2 LCP: I CONFACK [ACKsent] id 57 len 15 *Mar 1 06:16:01.639: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:01.639: Se1/2 LCP: MagicNumber 0x14D756C0 (0x050614D756C0) *Mar 1 06:16:01.639: Se1/2 LCP: State is Open *Mar 1 06:16:01.639: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:16:01.639: Se1/2 CHAP: O CHALLENGE id 7 len 24 from "Two" *Mar 1 06:16:01.647: Se1/2 CHAP: I CHALLENGE id 7 len 24 from "One" *Mar 1 06:16:01.651: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:16:01.651: Se1/2 CHAP: Using password from AAA *Mar 1 06:16:01.651: Se1/2 CHAP: O RESPONSE id 7 len 24 from "Two" *Mar 1 06:16:01.659: Se1/2 CHAP: I RESPONSE id 7 len 24 from "On R3(config-if)#e" *Mar 1 06:16:01.663: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:16:01.663: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:16:01.663: Se1/2 CHAP: O FAILURE id 7 len 25 msg is "Authentication failed" *Mar 1 06:16:01.671: Se1/2 PPP: Sending Acct Event[Down] id[15] *Mar 1 06:16:01.675: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:16:01.675: Se1/2 LCP: O TERMREQ [Open] id 58 len 4 *Mar 1 06:16:01.683: Se1/2 LCP: I TERMACK [TERMsent] id 58 len 4 *Mar 1 06:16:01.683: Se1/2 LCP: State is Closed *Mar 1 06:16:01.683: Se1/2 PPP: Phase is DOWN *Mar 1 06:16:01.687: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:16:01.687: Se1/2 LCP: State is Listen R3(config-if)#do u all All possible debugging has been turned off R3(config-if)# *Mar 1 06:16:03.651: Se1/2 LCP: I TERMREQ [Listen] id 42 len 4 *Mar 1 06:16:03.651: Se1/2 LCP: O TERMACK [Listen] id 42 len 4 *Mar 1 06:16:03.675: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:16:03.675: Se1/2 LCP: O CONFREQ [Listen] id 59 len 15 *Mar 1 06:16:03.675: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:03.675: Se1/2 LCP: MagicNumber 0x14D766A1 (0x050614D766A1) R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#sh    dh   o sh run \  Building configuration... Current configuration : 1516 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R3 ! boot-start-marker boot-end-marker ! ! no network-clock-participate slot 1 no network-clock-participate wic 0 no aaa new-model ip subnet-zero ! ! ! ip cef no ip domain lookup --More--  ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! username One password 0 For-The-Money ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] *M(0x0305C22305) *Mar 1 06:16:32.738: Se1/2 LCP: MagicNumber 0x14D7B8C9 (0x050614D7B8C9) *Mar 1 06 R2#:16:32.742: Se1/2 LCP: I CONFACK [ACKsent] id 56 len 15 *Mar 1 06:16:32.742: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:32.742: Se1/2 LCP: MagicNumber 0x14B9B689 (0x050614B9B689) *Mar 1 06:16:32.746: Se1/2 LCP: State is Open *Mar 1 06:16:32.746: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:16:32.746: Se1/2 CHAP: O CHALLENGE id 14 len 24 from "One" *Mar 1 06:16:32.746: Se1/2 CHAP: I CHALLENGE id 14 len 24 from "Two" *Mar 1 06:16:32.750: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:16:32.750: Se1/2 CHAP: Using password from AAA *Mar 1 06:16:32.750: Se1/2 CHAP: O RESPONSE id 14 len 24 from "One" *Mar 1 06:16:32.758: Se1/2 CHAP: I RESPONSE id 14 len 24 from "Two" *Mar 1 06:16:32.758: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:16:32.758: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:16:32.762: Se1/2 CHAP: O FAILURE id 14 len 25 msg is "Authentication failed" *Mar 1 06:16:32.762: Se1/2 PPP: Sending Acct Event[Down] id[1C] *Mar 1 06:16:32.766: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:16:32.766: Se1/2 LCP: O TERMREQ [Open] id 57 len 4 *Mar 1 06:16:32.766: Se1/2 CHAP: LCP not open, discarding packet *Mar 1 06:16:32.766: Se1/2 LCP: I TERMREQ [TERMsent] id 76 len 4 *Mar 1 06:16:32.766: Se1/2 LCP: O TERMACK [TERMsent] id 76 len 4 *Mar 1 06:16:32.770: Se1/2 LCP: I TERMACK [TERMsent] id 57 len 4 *Mar 1 06:16:32.774: Se1/2 LCP: State is Closed *Mar 1 06:16:32.774: Se1/2 PPP: Phase is DOWN *Mar 1 06:16:32.774: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:16:32.774: Se1/2 LCP: State is Listen *Mar 1 06:16:34.778: Se1/2 LCP: I CONFREQ [Listen] id 77 len 15 *Mar 1 06:16:34.778: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:34.778: Se1/2 LCP: MagicNumber 0x14D7C0C9 (0x050614D7C0C9) *Mar 1 06:16:34.778: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:16:34.786: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:16:34.786: Se1/2 LCP: O CONFREQ [Listen] id 58 len 15 *Mar 1 06:16:34.786: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:34.786: Se1/2 LCP: MagicNumber 0x14B9BE8D (0x050614B9BE8D) *Mar 1 06:16:34.794: Se1/2 LCP: I CONFACK [REQsent] id 58 len 15 *Mar 1 06:16:34.794: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:34.794: Se1/2 LCP: MagicNumber 0x14B9BE8D (0x050614B9BE8D) R2# R2# *Mar 1 06:16:36.797: Se1/2 LCP: I CONFREQ [ACKrcvd] id 78 len 15 *Mar 1 06:16:36.797: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:36.797: Se1/2 LCP: MagicNumber 0x14D7C0C9 (0x050614D7C0C9) *Mar 1 06:16:36.797: Se1/2 LCP: O CONFACK [ACKrcvd] id 78 len 15 *Mar 1 06:16:36.797: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:36.801: Se1/2 LCP: MagicNumber 0x14D7C0C9 (0x050614D7C0C9) *Mar 1 06:16:36.801: Se1/2 LCP: State is Open *Mar 1 06:16:36.801: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:16:36.801: Se1/2 CHAP: O CHALLENGE id 15 len 24 from "One" *Mar 1 06:16:36.809: Se1/2 CHAP: I CHALLENGE id 15 len 24 from "Two" *Mar 1 06:16:36.813: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:16:36.813: Se1/2 CHAP: Using password from AAA *Mar 1 06:16:36.813: Se1/2 CHAP: O RESPONSE id 15 len 24 from "One" *Mar 1 06:16:36.817: Se1/2 CHAP: I RESPONSE id 15 len 24 from "Two" *Mar 1 06:16:36.817: Se1/2 PPP: Phase is FORWARD R2#dING, Attempting Forward *Mar 1 06:16:36.817: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:16:36.817: Se1/2 CHAP: O FAILURE id 15 len 25 msg is "Authentication failed" *Mar 1 06:16:36.821: Se1/2 PPP: Sending Acct Event[Down] id[1D] *Mar 1 06:16:36.821: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:16:36.821: Se1/2 LCP: O TERMREQ [Open] id 59 len 4 *Mar 1 06:16:36.825: Se1/2 CHAP: LCP not open, discarding packet *Mar 1 06:16:36.829: Se1/2 LCP: I TERMREQ [TERMsent] id 79 len 4 *Mar 1 06:16:36.829: Se1/2 LCP: O TERMACK [TERMsent] id 79 len 4 *Mar 1 06:16:36.829: Se1/2 LCP: I TERMACK [TERMsent] id 59 len 4 *Mar 1 06:16:36.829: Se1/2 LCP: State is Closed *Mar 1 06:16:36.829: Se1/2 PPP: Phase is DOWN R2#d  *Mar 1 06:16:38.844: Se1/2 LCP: I CONFREQ [Closed] id 80 len 15 *Mar 1 06:16:38.844: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:38.844: Se1/2 LCP: MagicNumber 0x14D7D0AE (0x050614D7D0AE) *Mar 1 06:16:38.844: Se1/2 LCP: Missed a Link-Up transition, starting PPP *Mar 1 06:16:38.844: Se1/2 PPP: Using default call direction *Mar 1 06:16:38.844: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:16:38.848: Se1/2 PPP: Session handle[7400001C] Session id[27] *Mar 1 06:16:38.848: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:16:38.848: Se1/2 LCP: O CONFREQ [Closed] id 60 len 15 *Mar 1 06:16:38.848: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:38.848: Se1/2 LCP: MagicNumber 0x14B9CE6E (0x050614B9CE6E) *Mar 1 06:16:38.848: Se1/2 LCP: O CONFACK [REQsent] id 80 len 15 *Mar 1 06:16:38.848: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:38.852: Se1/2 LCP: MagicNumber 0x14D7D0AE (0x050614D7D0AE) *Mar 1 06 R2#uy all ^ % Invalid input detected at '^' marker. R2#:16:38.856: Se1/2 LCP: I CONFACK [ACKsent] id 60 len 15 *Mar 1 06:16:38.856: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:38.856: Se1/2 LCP: MagicNumber 0x14B9CE6E (0x050614B9CE6E) *Mar 1 06:16:38.860: Se1/2 LCP: State is Open *Mar 1 06:16:38.860: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:16:38.860: Se1/2 CHAP: O CHALLENGE id 16 len 24 from "One" *Mar 1 06:16:38.860: Se1/2 CHAP: I CHALLENGE id 16 len 24 from "Two" *Mar 1 06:16:38.864: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:16:38.864: Se1/2 CHAP: Using password from AAA *Mar 1 06:16:38.864: Se1/2 CHAP: O RESPONSE id 16 len 24 from "One" *Mar 1 06:16:38.872: Se1/2 CHAP: I RESPONSE id 16 len 24 from "Two" *Mar 1 06:16:38.872: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:16:38.872: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:16:38.876: Se1/2 CHAP: O FAILURE id 16 len 25 msg is "Authentication failed" *Mar 1 06:16:38.876: Se1/2 PPP: Sending Acct Event[Down] id[1E] *Mar 1 06:16:38.880: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:16:38.880: Se1/2 LCP: O TERMREQ [Open] id 61 len 4 *Mar 1 06:16:38.880: Se1/2 CHAP: LCP not open, discarding packet *Mar 1 06:16:38.880: Se1/2 LCP: I TERMREQ [TERMsent] id 81 len 4 *Mar 1 06:16:38.880: Se1/2 LCP: O TERMACK [TERMsent] id 81 len 4 *Mar 1 06:16:38.884: Se1/2 LCP: I TERMACK [TERMsent] id 61 len 4 *Mar 1 06:16:38.888: Se1/2 LCP: State is Closed *Mar 1 06:16:38.888: Se1/2 PPP: Phase is DOWN *Mar 1 06:16:38.888: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:16:38.888: Se1/2 LCP: State is Listen *Mar 1 06:16:40.892: Se1/2 LCP: I CONFREQ [Listen] id 82 len 15 *Mar 1 06:16:40.892: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:40.892: Se1/2 LCP: MagicNumber 0x14D7D8AE (0x050614D7D8AE) *Mar 1 06:16:40.892: Se1/2 LCP: Dropping packet, state is Listen *Mar 1 06:16:40.896: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:16:40.896: Se1/2 LCP: O CONFREQ [Listen] id 62 len 15 *Mar 1 06:16:40.896: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:40.896: Se1/2 LCP: MagicNumber 0x14B9D66E (0x050614B9D66E) *Mar 1 06:16:40.904: Se1/2 LCP: I CONFACK [REQsent] id 62 len 15 *Mar 1 06:16:40.904: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:40.904: Se1/2 LCP: MagicNumber 0x14B9D66E (0x050614B9D66E) R2#u all All possible debugging has been turned off R2# *Mar 1 06:16:42.907: Se1/2 LCP: I CONFREQ [ACKrcvd] id 83 len 15 *Mar 1 06:16:42.907: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:42.907: Se1/2 LCP: MagicNumber 0x14D7D8AE (0x050614D7D8AE) *Mar 1 06:16:42.907: Se1/2 LCP: O CONFACK [ACKrcvd] id 83 len 15 *Mar 1 06:16:42.907: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:16:42.911: Se1/2 LCP: MagicNumber 0x14D7D8AE (0x050614D7D8AE) *Mar 1 06:16:42.911: Se1/2 LCP: State is Open *Mar 1 06:16:42.911: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:16:42.911: Se1/2 CHAP: O CHALLENGE id 17 len 24 from "One" *Mar 1 06:16:42.919: Se1/2 CHAP: I CHALLENGE id 17 len 24 from "Two" *Mar 1 06:16:42.923: Se1/2 CHAP: Using hostname from interface CHAP *Mar 1 06:16:42.923: Se1/2 CHAP: Using password from AAA *Mar 1 06:16:42.923: Se1/2 CHAP: O RESPONSE id 17 len 24 from "One" *Mar 1 06:16:42.923: Se1/2 CHAP: I RESPONSE id 17 len 24 from "Two" *Mar 1 06:16:42.927: Se1/2 PPP: Phase is FORWARD R2#ING, Attempting Forward *Mar 1 06:16:42.927: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:16:42.927: Se1/2 CHAP: O FAILURE id 17 len 25 msg is "Authentication failed" *Mar 1 06:16:42.931: Se1/2 PPP: Sending Acct Event[Down] id[1F] *Mar 1 06:16:42.931: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:16:42.931: Se1/2 LCP: O TERMREQ [Open] id 63 len 4 *Mar 1 06:16:42.935: Se1/2 CHAP: LCP not open, discarding packet *Mar 1 06:16:42.939: Se1/2 LCP: I TERMREQ [TERMsent] id 84 len 4 *Mar 1 06:16:42.939: Se1/2 LCP: O TERMACK [TERMsent] id 84 len 4 *Mar 1 06:16:42.939: Se1/2 LCP: I TERMACK [TERMsent] id 63 len 4 *Mar 1 06:16:42.939: Se1/2 LCP: State is Closed *Mar 1 06:16:42.939: Se1/2 PPP: Phase is DOWN R2# R2# R2# R2# R2#confi       sh run int s 1/2 Building configuration... Current configuration : 195 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp authentication chap optional ppp chap hostname One ppp chap password 0 For-The-Money end R2# *Mar 1 06:16:53.216: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down R2# *Mar 1 06:16:55.215: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 176 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication chap optional ppp chap hostname Two ppp chap password 0 For-The-Show end R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | i user username Two password 0 For-The-Show R2# *Mar 1 06:18:44.254: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down R2# *Mar 1 06:18:46.253: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up R2# *Mar 1 06:20:01.729: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down R2# *Mar 1 06:20:03.728: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#shut R2(config-if)#do sh run i *Mar 1 06:23:32.567: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down R2(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 205 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp shutdown clock rate 64000 ppp authentication chap optional ppp chap hostname One ppp chap password 0 For-The-Money end R2(config-if)#mp    no ppp chap hostname One R2(config-if)#no ppp chap password 0 For-The-Money R2(config-if)#no ppp authentication chap optional R2(config-if)#ppp authentication pap optional R2(config-if)# ppp pap sent-username One password 0 For-The-Money R2(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] * R3(config-if)#do sh run int s 1/2 u all no shut do deb ppp neppp chap password For-The-Shownppp chap password For-The-Showoppp chap password For-The-Show ppp chap password For-The-Show R3(config-if)#no ppp chap password For-The-Showdo sh run int s 1/2  u all no shut do deb ppp neppp chap password For-The-Showhost Two nppp chap host Twooppp chap host Two ppp chap host Two R3(config-if)#ppp authentication pap optional R3(config-if)# ppp pap sent-username Two password 0 For-The-Show R3(config-if)#^Z R3#do     *Mar 1 06:24:10.461: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int s 1/2 Building configuration... Current configuration : 169 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show end R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#no shut R2(config-if)#^Z R2# *Mar 1 06:24:29.456: %SYS-5-CONFIG_I: Configured from console by console R2# *Mar 1 06:24:31.006: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up R2# *Mar 1 06:24:32.028: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#user R1 pass PinkCadillas c R3(config)#int s 1/0 R3(config-if)#fram inv  R3(config-if)#fram inter R3(config-if)#fram interface-d R3(config-if)#fram interface-dlci 301 ? ppp Use RFC1973 Encapsulation to support PPP over FR switched Define a switched DLCI R3(config-if)#fram interface-dlci 301 ppp ? Virtual-Template Virtual Template interface R3(config-if)#fram interface-dlci 301 ppp vi R3(config-if)#fram interface-dlci 301 ppp virtual-Template ? <1-200> Virtual-Template interface number R3(config-if)#fram interface-dlci 301 ppp virtual-Template 1 R3(config-fr-dlci)# *Mar 1 06:28:02.938: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R3(config-fr-dlci)#exity ^ % Invalid input detected at '^' marker. R3(config-fr-dlci)#exity  R3(config-if)#exit R3(config)#int vir R3(config)#int virtual-te R3(config)#int virtual-template 1 R3(config-if)#encap pp R3(config-if)#do sh run int vi r 1 sh run int vr 1 ^ % Invalid input detected at '^' marker. R3(config-if)#do sh run int vr 1ir 1 % Ambiguous command: "sh run int vir 1" R3(config-if)#do sh run int vir 1t 1u 1 % Ambiguous command: "sh run int virtu 1" R3(config-if)#do sh run int virtu 1a 1l 1 1  1 a 1l 1- 1t 1e 1m 1 Building configuration... Current configuration : 50 bytes ! interface Virtual-Template1 no ip address end R3(config-if)# R3(config-if)# R3(config-if)#ip ~    un R3(config-if)#ip unn R3(config-if)#ip unnumbered ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config-if)#ip unnumbered s 1/0 R3(config-if)#ppp authen cha R3(config-if)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#i yus   user R3 pass PinkCadillac R1(config)#int s 1/  0/0.1 R1(config-subif)#fram in R1(config-subif)#fram inter R1(config-subif)#fram interface-dlci 103 pp vit R1(config-subif)#fram interface-dlci 103 pp vit r R1(config-subif)#fram interface-dlci 103 pp virtual-Template 2 R1(config-fr-dlci)# *Mar 1 06:32:09.494: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R1(config-fr-dlci)# *Mar 1 06:32:10.736: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up R1(config-fr-dlci)#exit R1(config-subif)#exit R1(config)#int vir R1(config)#int virtual-temp R1(config)#int virtual-template 2 R1(config-if)#ip add 208.28.1.1 255.25.255    5.255.248 R1(config-if)#ppp authen chap R1(config-if)#do    do p 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R1(config-if)#do sj    sh in t s 0-       t s0/0.1 Serial0/0.1 is up, line protocol is up Hardware is PowerQUICC Serial Internet address is 208.28.1.1/29 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never R1(config-if)#do sh int s0/0.1irint s0/0.1uint s0/0.1nint s0/0.1 int s0/0.1 Building configuration... Current configuration : 118 bytes ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 end R1(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 0 R3(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 169 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show end R3(config-if)#do sh run int s 1/2 0 Building configuration... Current configuration : 333 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 broadcast frame-relay interface-dlci 301 ppp Virtual-Template1 no frame-relay inverse-arp end R3(config-if)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)#do sh run int s0/0.1 int s 00 /0.1 R1(config-subif)#int s 0/0.1do sh run int s0/0.1int s0/0.1 p 208.28.1.2 ppp authen chapip add 208.28.1.1 255.255.255.248nt virtual-template 2 exit fram interface-dlci 103 pp virtual-Template 2                      bfram interface-dlci 103fram interface-dlci 103 nfram interface-dlci 103ofram interface-dlci 103 fram interface-dlci 103 R1(config-subif)#no fram interface-dlci 103 *Mar 1 06:34:15.878: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down *Mar 1 06:34:16.879: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to down R1(config-subif)#no fram interface-dlci 103int s 0/0.1 do sh run int s0/0.1int s0/0.1 p 208.28.1.2 ppp authen chapip add 208.28.1.1 255.255.255.248nt virtual-template 2 exit fram interface-dlci 103 pp virtual-Template 2 R1(config-fr-dlci)# *Mar 1 06:34:20.665: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R1(config-fr-dlci)#do sh run *Mar 1 06:34:21.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up R1(config-fr-dlci)#do sh run n           ^Z R1# *Mar 1 06:34:26.275: %SYS-5-CONFIG_I: Configured from console by console R1#co f    confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int vir R1(config)#int virtual-temp R1(config)#int virtual-template 2 R1(config-if)#do sh run int virtual-template 2 Building configuration... Current configuration : 99 bytes ! interface Virtual-Template2 ip address 208.28.1.1 255.255.255.248 ppp authentication chap end R1(config-if)#int s /0. ^ % Invalid input detected at '^' marker. R1(config)#1int s /0. 0/0. % Incomplete command. R1(config)#int s 0/0.1 R1(config-subif)#i no ip add R1(config-subif)# R1(config-subif)# R1(config-subif)# R1(config-subif)# R1(config-subif)#do sh iop    p int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 unassigned YES manual up up Ethernet0/1 17.57.100.1 YES manual up up Serial0/1 unassigned YES unset administratively down down Virtual-Access1 208.28.1.1 YES TFTP up up Virtual-Access2 unassigned YES unset down down Virtual-Template2 208.28.1.1 YES manual down down R1(config-subif)#p   do p 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/68/84 ms R1(config-subif)#^Z R1# *Mar 1 06:35:49.579: %SYS-5-CONFIG_I: Configured from console by console R1#p 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do p 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 113/117/124 ms R3(config-if)#do sh run int s 1/2 0 Building configuration... Current configuration : 333 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 broadcast frame-relay interface-dlci 301 ppp Virtual-Template1 no frame-relay inverse-arp end R3(config-if)#no frame-relay map ip 208.28.1.1 301 broadcast ^ % Invalid input detected at '^' marker. R3(config-if)#int s 1/0 R3(config-if)#int s 1/0no frame-relay map ip 208.28.1.1 301 broadcast R3(config-if)#p   do p 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/64 ms R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#^Z R3# *Mar 1 06:35:30.964: %SYS-5-CONFIG_I: Configured from console by console R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b user username R3 password 0 PinkCadillac ! ! ! ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial0/0.1 point-to-point frame-relay interface-dlci 103 ppp Virtual-Template2 ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 half-duplex ! interface Serial0/1 no ip address --More--   shutdown ! interface Virtual-Template2 ip address 208.28.1.1 255.255.255.248 ppp authentication chap ! ip http server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! --More-- RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b user username One password 0 For-The-Money username R1 password 0 PinkCadillac ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto --More--   speed auto ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 broadcast frame-relay interface-dlci 301 ppp Virtual-Template1 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show ! interface Serial1/3 --More--   no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! interface Virtual-Template1 ip unnumbered Serial1/0 ppp authentication chap ! --More--   R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int s 1/2 R3(config-if)#ppp ? accm Set initial Async Control Character Map accounting Set PPP network accounting method acfc Options for HDLC Address & Control Field Compression authentication Set PPP link authentication method authorization Set PPP network authorization method bridge Enable PPP bridge translation caller Caller option when no CLID is available chap Set CHAP authentication parameters direction Override default PPP direction dnis Authentication via DNIS before LCP eap Set EAP authentication parameters encrypt Enable PPP encryption ipcp Set IPCP negotiation options iphc Set IPCP Header Compression control options lcp PPP LCP configuration link Set miscellaneous link parameters loopback PPP loopback options max-bad-auth Allow multiple authentication failures max-configure Number of conf-reqs sent before assuming peer is unable to respond max-failure Number of conf-naks sent before assuming configuration is not converging --More--   max-terminate Number of term-reqs sent before assuming peer is unable to respond ms-chap Set MS-CHAP authentication parameters ms-chap-v2 Set MS-CHAP-V2 authentication parameters multilink Make interface multilink capable pap Set PAP authentication parameters pfc Options for Protocol Field Compression quality Set parameters related to Link Quality Monitoring (LQM) reliable-link Use LAPB with PPP to provide a reliable link timeout Set PPP timeout parameters R3(config-if)#ppp reliable-link R3(config-if)#^Z R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#ppp rel R2(config-if)#ppp reliable-link R2(config-if)#shut R2(config-if)#no    de  *Mar 1 06:39:03.969: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 06:39:04.971: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R2(config-if)#do deb ppp neo deb ppp neo ^ % Invalid input detected at '^' marker. R2(config-if)#do deb ppp neo  PPP protocol negotiation debugging is on R2(config-if)#no shut R2(config-if)#^Z R2# *Mar 1 06:39:13.521: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:39:13.545: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:39:13.569: Se1/2 PPP: Outbound cdp packet dropped R2# *Mar 1 06:39:14.006: %SYS-5-CONFIG_I: Configured from console by console R2# *Mar 1 06:39:15.496: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 06:39:15.496: Se1/2 PPP: Using default call direction *Mar 1 06:39:15.496: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:39:15.496: Se1/2 PPP: Session handle[FC0000BF] Session id[191] *Mar 1 06:39:15.496: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:39:15.496: Se1/2 LCP: O CONFREQ [Closed] id 165 len 18 *Mar 1 06:39:15.496: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:39:15.500: Se1/2 LCP: MagicNumber 0x14CE82C9 (0x050614CE82C9) *Mar 1 06:39:15.500: Se1/2 LCP: ReliableLink window 7 addr 1 (0x0B040701) *Mar 1 06:39:15.500: Se1/2 LCP: I CONFREQ [REQsent] id 186 len 18 *Mar 1 06:39:15.500: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:39:15.500: Se1/2 LCP: MagicNumber 0x14EC8514 (0x050614EC8514) *Mar 1 06:39:15.504: Se1/2 LCP: ReliableLink window 7 addr 3 (0x0B040703) *Mar 1 06:39:15.504: Se1/2 LCP: O CONFACK [REQsent] id 186 l R2#en 18 *Mar 1 06:39:15.504: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:39:15.504: Se1/2 LCP: MagicNumber 0x14EC8514 (0x050614EC8514) *Mar 1 06:39:15.504: Se1/2 LCP: ReliableLink window 7 addr 3 (0x0B040703) *Mar 1 06:39:15.508: Se1/2 LCP: I CONFACK [ACKsent] id 165 len 18 *Mar 1 06:39:15.508: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:39:15.508: Se1/2 LCP: MagicNumber 0x14CE82C9 (0x050614CE82C9) *Mar 1 06:39:15.508: Se1/2 LCP: ReliableLink window 7 addr 1 (0x0B040701) *Mar 1 06:39:15.508: Se1/2 LCP: State is Open *Mar 1 06:39:15.512: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:39:15.512: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:39:15.512: Se1/2 PAP: Using password from interface PAP *Mar 1 06:39:15.516: Se1/2 PAP: O AUTH-REQ id 15 len 22 from "One" *Mar 1 06:39:15.528: Se1/2 PAP: I AUTH-ACK id 15 len 5 R2# *Mar 1 06:39:25.505: Se1/2 AUTH: Timeout 1 *Mar 1 06:39:25.505: Se1/2 PAP: I AUTH-REQ id 16 len 21 from "Two" *Mar 1 06:39:25.505: Se1/2 PAP: Authenticating peer Two *Mar 1 06:39:25.505: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:39:25.505: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:39:25.509: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:39:25.509: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 06:39:25.513: Se1/2 PAP: O AUTH-ACK id 16 len 5 *Mar 1 06:39:25.513: Se1/2 PPP: Phase is UP *Mar 1 06:39:25.513: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 06:39:25.513: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:39:25.517: Se1/2 PPP: Process pending ncp packets *Mar 1 06:39:25.517: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 06:39:25.521: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 06:39:25.521: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 R2# 06:39:25.521: Se1/2 AAA/AUTHOR/IPCP: Start. Her address 180.40.7.3, we want 0.0.0.0 *Mar 1 06:39:25.521: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 06:39:25.525: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 06:39:25.525: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 06:39:25.525: Se1/2 CDPCP: State is Open *Mar 1 06:39:25.525: Se1/2 AAA/AUTHOR/IPCP: Reject 180.40.7.3, using 0.0.0.0 *Mar 1 06:39:25.529: Se1/2 AAA/AUTHOR/IPCP: Done. Her address 180.40.7.3, we want 0.0.0.0 *Mar 1 06:39:25.529: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 06:39:25.529: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:39:25.529: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 06:39:25.529: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:39:25.529: Se1/2 IPCP: State is Open *Mar 1 06:39:25.533: Se1/2 IPCP: Install route to 180.40.7.3 *Mar 1 06:39:25.533: Se1/2 IPCP: Add link info for cef entry 180.40.7.3 *Mar 1 06:39:26.514: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2# R2#u all All possible debugging has been turned off R2#sh int s 1/2 Serial1/2 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is 180.40.7.2/27 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, LCP Open Open: CDPCP, IPCP LAPB DCE, state CONNECT, modulo 8, k 7, N1 12048, N2 3 T1 3000, T2 0, interface outage (partial T3) 0, T4 0, PPP over LAPB VS 2, VR 5, tx NR 5, Remote VR 2, Retransmissions 0 Queues: U/S frames 0, I frames 0, unack. 0, reTx 0 IFRAMEs 26/29 RNRs 0/0 REJs 0/0 SABM/Es 1/1 FRMRs 0/0 DISCs 0/0, loopback not set Keepalive set (10 sec) Last input 00:00:02, output 00:00:02, output hang never Last clearing of "show interface" counters 00:41:49 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec --More--   R2#sh run int s 1/2 Building configuration... Current configuration : 207 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp reliable-link ppp authentication pap optional ppp pap sent-username One password 0 For-The-Money end R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#shj    run itn  nt s 1/2 Building configuration... Current configuration : 188 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp reliable-link ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show end R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh run int atm 1/0 Building configuration... Current configuration : 72 bytes ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive end R4#conf it ^ % Invalid input detected at '^' marker. R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int s atm 1/9 ^ % Invalid input detected at '^' marker. R4(config)#int atm 1/9 0 R4(config-if)#ip add 192.10.32.13 255.255.255.0 R4(config-if)#pvc 0/72 R4(config-if-atm-vc)#pr R4(config-if-atm-vc)#protocol 192.10.32.2543  4 R4(config-if-atm-vc)#exit R4(config-if)#no shut R4(config-if)#do p 19 *Mar 1 06:45:38.242: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up *Mar 1 06:45:39.242: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up R4(config-if)#do p 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R4(config-if)#exit R4(config)#access      ip access            RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip a route 0.0.0.0 0.0.0.0 17.80.1.2 R3(config)#^Z R3#p 1 *Mar 1 06:45:19.653: %SYS-5-CONFIG_I: Configured from console by console R3#p 19. 2.      do sh       sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 17.80.1.2 to network 0.0.0.0 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.1/32 is directly connected, Virtual-Access1 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/16 is variably subnetted, 2 subnets, 2 masks C 180.40.7.2/32 is directly connected, Serial1/2 C 180.40.7.0/27 is directly connected, Serial1/2 S* 0.0.0.0/0 [1/0] via 17.80.1.2 R3#p 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R3#p 192.10.32.254~    13 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.13, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config)#ip access-list P st Prob9 R4(config-std-nacl)#per any R4(config-std-nacl)#exit R4(config)#ip anat    nat ? Stateful Stateful NAT configuration commands inside Inside address translation log NAT Logging outside Outside address translation pool Define pool of addresses service Special translation for application using non-standard port translation NAT translation entry configuration R4(config)#ip nat in R4(config)#ip nat inside sou R4(config)#ip nat inside source ? list Specify access list describing local addresses route-map Specify route-map static Specify static local->global mapping R4(config)#ip nat inside source li R4(config)#ip nat inside source list ? <1-2699> Access list number for local addresses WORD Access list name for local addresses R4(config)#ip nat inside source list Prob9 ? interface Specify interface for global address pool Name pool of global addresses R4(config)#ip nat inside source list Prob9 int ? ATM ATM interface Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R4(config)#ip nat inside source list Prob9 int atm 1/0 ? overload Overload an address translation vrf Specify vrf R4(config)#ip nat inside source list Prob9 int atm 1/0 o R4(config)#ip nat inside source list Prob9 int atm 1/0 overload R4(config)#int atm 1/0 R4(config-if)#ip nat out R4(config-if)#iont     nt fa 0/0 R4(config-if)#ip i nat in R4(config-if)#eixt ^ % Invalid input detected at '^' marker. R4(config-if)#exit R4(config)#exit R4# *Mar 1 06:54:04.330: %SYS-5-CONFIG_I: Configured from console by console R4#p 192.10.32.254 sou 17.80.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: Packet sent with a source address of 17.80.1.2 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R4#sh nat tran ^ % Invalid input detected at '^' marker. R4#sh nat traninat tranpnat tran nat tran Pro Inside global Inside local Outside local Outside global icmp 192.10.32.13:1 17.80.1.2:1 192.10.32.254:1 192.10.32.254:1 tcp 192.10.32.13:1 192.10.32.13:179 192.10.32.254:42714 192.10.32.254:42714 R4# R4# R4# R4# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#p 192.10.32.243  54 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip nat tran Pro Inside global Inside local Outside local Outside global icmp 192.10.32.13:1 17.80.1.2:1 192.10.32.254:1 192.10.32.254:1 icmp 192.10.32.13:10 17.80.1.1:10 192.10.32.254:10 192.10.32.254:10 tcp 192.10.32.13:1 192.10.32.13:179 192.10.32.254:42714 192.10.32.254:42714 R4# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#p 192.10.32.254 p 192.10.32.254p 192.10.32.254 192.10.32.254  Trying 192.10.32.254 ... Open CR1> CR1> CR1> CR1>q [Connection to 192.10.32.254 closed by foreign host] R3# R3#coi t ^ % Invalid input detected at '^' marker. R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip route 0.0.0.0 0.0.0.0 17.80.1.2nip route 0.0.0.0 0.0.0.0 17.80.1.2oip route 0.0.0.0 0.0.0.0 17.80.1.2 ip route 0.0.0.0 0.0.0.0 17.80.1.2 R3(config)#^Z R3# *Mar 1 06:53:11.058: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.1/32 is directly connected, Virtual-Access1 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/16 is variably subnetted, 2 subnets, 2 masks C 180.40.7.2/32 is directly connected, Serial1/2 C 180.40.7.0/27 is directly connected, Serial1/2 R3#sh ip routeconfi t i t 192.10.32.254p 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip nat ? Stateful Stateful NAT configuration commands inside Inside address translation log NAT Logging outside Outside address translation pool Define pool of addresses service Special translation for application using non-standard port translation NAT translation entry configuration R4(config)#ip nat out ? source Source address translation R4(config)#ip nat out sou ? list Specify access list describing global addresses route-map Specify route-map static Specify static global->local mapping R4(config)#ip nat out sou st ? A.B.C.D Outside global IP address network Subnet translation tcp Transmission Control Protocol udp User Datagram Protocol R4(config)#ip nat out sou st 192./ 10.32.254 ? A.B.C.D Outside local IP address R4(config)#ip nat out sou st 192.10.32.254 17.80.1.3 R4(config)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#p 17.80.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.3, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms R3# R3# R3# R3#p 17.80.1.3p 17.80.1.3 17.80.1.3  Trying 17.80.1.3 ... % Connection refused by remote host R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config)#ip nat out sou st 192.10.32.254 17.80.1.3 ? add-route Add a static route for outside local address extendable Extend this translation when used no-alias Do not create an alias for the local address no-payload No translation of embedded address/port in the payload redundancy NAT redundancy operation vrf Specify vrf R4(config)#ip nat out sou st 192.10.32.254 17.80.1.3 no R4(config)#ip nat out sou st 192.10.32.254 17.80.1.3 no-al R4(config)#ip nat out sou st 192.10.32.254 17.80.1.3 no-alias R4(config)#ip rout 17.9 80.1.3 255.255.255.255 192.10.32.254 R4(config)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#17.80.1.3 Trying 17.80.1.3 ... Open CR1>q [Connection to 17.80.1.3 closed by foreign host] R3# R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config)#ip rout 17.80.1.3 255.255.255.255 192.10.32.254nip rout 17.80.1.3 255.255.255.255 192.10.32.254oip rout 17.80.1.3 255.255.255.255 192.10.32.254 ip rout 17.80.1.3 255.255.255.255 192.10.32.254 % Ambiguous command: "no ip rout 17.80.1.3 255.255.255.255 192.10.32.254" R4(config)#no ip rout 17.80.1.3 255.255.255.255 192.10.32.254         no ip rout 17.80.1.3 255.255.255.255 192.10.32.254e 17.80.1.3 255.255.255.255 192.10.32.254 R4(config)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#17.80.1.3 Trying 17.80.1.3 ... RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config)#no ip route 17.80.1.3 255.255.255.255 192.10.32.254 17.80.1.3 255.255.255.255 192.10.32.254 ip rout 17.80.1.3 255.255.255.255 192.10.32.254 nat out sou st 192.10.32.254 17.80.1.3 no-alias ad R4(config)#ip nat out sou st 192.10.32.254 17.80.1.3 no-alias add-route R4(config)# RACK13AS>3 [Resuming connection 3 to r3 ... ] % C R3#17.80.1.3 Trying 17.80.1.3 ... Open CR1>q [Connection to 17.80.1.3 closed by foreign host] R3# R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config)#ip nat out sou st 192.10.32.254 17.80.1.3 no-alias add-route  no-alias add-route 2 no-alias add-route 5 no-alias add-route 4 no-alias add-route  % 192.10.32.254 already mapped (17.80.1.3 -> 192.10.32.254) R4(config)#ip nat out sou st 192.10.32.254 17.80.1.254 no-alias add-route 3 no-alias add-route ex R4(config)#$sou st 192.10.32.254 17.80.1.3 no-alias add-route extendable R4(config)#$sou st 192.10.32.254 17.80.1.3 no-alias add-route extendable ip nat out sou st 192.10.32.254 17.80.1.254 no-alias add-route ex R4(config)#ip nat out sou st 192.10.32.254 17.80.1.254 no-alias add-route ex$sou st 192.10.32.254 17.80.1.3 no-alias add-route extendable ip nat out sou st 192.10.32.254 17.80.1.254 no-alias add-route ex4 no-alias add-route ex 2 no-alias add-route ex R4(config)#ip nat out sou st 192.10.32.254 17.80.1.252 no-alias add-route ex  no-alias add-route ex 0 no-alias add-route ex R4(config)#^Z R4# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#17.80.1.3 254 Trying 17.80.1.254 ... Open CR1>q [Connection to 17.80.1.254 closed by foreign host] R3#17.80.1.254 2 Trying 17.80.1.252 ... Open CR1>q [Connection to 17.80.1.252 closed by foreign host] R3#17.80.1.252 0 Trying 17.80.1.250 ... Open CR1>q [Connection to 17.80.1.250 closed by foreign host] R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] *Mar 1 07:01:37.218: %SYS R4#sh ver Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3620-IK9O3S7-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Thu 10-Nov-05 03:19 by evmiller Image text-base: 0x60008B00, data-base: 0x6193C000 ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) ROM: 3600 Software (C3620-IK9O3S7-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) R4 uptime is 7 hours, 2 minutes System returned to ROM by power-on System image file is "flash:c3620-ik9o3s7-mz.123-16a.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you --More--   R4# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ver Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller Image text-base: 0x80008098, data-base: 0x8202B100 ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) ROM: C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) R3 uptime is 6 hours, 59 minutes System returned to ROM by power-on System image file is "flash:c2600-adventerprisek9-mz.123-16a.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you --More--   R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b 0/0 interface FastEthernet0/0 ip address 17.80.1.2 255.255.255.0 ip nat inside duplex auto speed auto ! interface ATM1/0 ip address 192.10.32.13 255.255.255.0 ip nat outside no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 ! ! ip nat inside source list Prob9 interface ATM1/0 overload ip nat outside source static 192.10.32.254 17.80.1.3 extendable no-alias add-route ip nat outside source static 192.10.32.254 17.80.1.254 extendable no-alias add-route ip nat outside source static 192.10.32.254 17.80.1.252 extendable no-alias add-route ip nat outside source static 192.10.32.254 17.80.1.250 extendable no-alias add-route --More--  ip http server no ip http secure-server ip classless ! ! ! ip access-list standard Prob9 permit any ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! end R4# R4#