=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2007.03.01 11:33:08 =~=~=~=~=~=~=~=~=~=~=~= RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#shg    run int s 1/0 Building configuration... Current configuration : 111 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon end R3# RACK13AS> [Resuming connection 3 to r3 ... ] R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh rnu int        un int s 1/0.1 Building configuration... Current configuration : 111 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay interface-dlci 203 end R2#sh run int s 1/0.1 2 Building configuration... Current configuration : 112 bytes ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay interface-dlci 201 end R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)# frame-relay interface-dlci 203 R2(config-fr-dlci)# frame-relay interface-dlci 203 exit R2(config-subif)#exit frame-relay interface-dlci 203n frame-relay interface-dlci 203o frame-relay interface-dlci 203 frame-relay interface-dlci 203 R2(config-subif)#fram map ip 208.28,.1   .1.2 2 203 R2(config-subif)#fram map ip 208.28.1.2 203  203 1 203  R2(config-subif)#int s 1/0.2 R2(config-subif)#no frame-relay interface-dlci 201 R2(config-subif)#fram map ip   180.40.7.66 201 R2(config-subif)#^Z R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#ci  confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#do sh run int s 1/0 Building configuration... Current configuration : 111 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon end R3(config-if)#no fram inv R3(config-if)#no fram inverse-arp R3(config-if)#fram map ip 208.28.1.1 301 R3(config-if)#fram map ip 208.28.1.1 301  1 2   2  302 3 302  R3(config-if)#do sh fram map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), static, CISCO, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), static, CISCO, status defined, active R3(config-if)#^Z R3# *Mar 1 15:35:48.566: %SYS-5-CONFIG_I: Configured from console by console R3#p 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/73/89 ms R3#p 208.28.1.1 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#rouetr     ter eigrp 100 S5(config-router)#net 208.28.1.130 0..0.0    0.0.0 S5(config-router)#net 208.28.1.130 0.0.0.0 0.0.0.0  0.0.0.0  0.0.0.0 6 0.0.0.05 0.0.0.0 S5(config-router)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1>en R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#line con 0 R1(config-line)#e no exec-time R1(config-line)#no    logg sync R1(config-line)#exit R1(config)#router eigrp 100 R1(config-router)#net 208.28.1.66 0.0.0.0 R1(config-router)#net 180.40.7. *Mar 1 15:38:39.915: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.65 (Ethernet0/0) is up: new adjacency R1(config-router)#net 180.40.7.66 0.0.0.0 R1(config-router)# RACK13AS>2 [Resuming connection 2 to r2 ... ] *M R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router bgp 10      eigrp 100 R2(config-router)#net 180.40.7.65 0.0.0.0 R2(config-router)#net 208.28.1.129 *Mar 1 15:38:02.593: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is up: new adjacency R2(config-router)#net 208.28.1.129 0.0.0.0 R2(config-router)# *Mar 1 15:38:09.120: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.130 (FastEthernet0/1) is up: new adjacency R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 208.28.1.130 Fa0/1 12 00:00:17 4 200 0 3 0 180.40.7.66 Se1/0.2 13 00:00:23 1 5000 2 0 R2(config-router)#nei 180.40.7.65 6 ser 1/0.2 R2(config-router)# *Mar 1 15:38:46.145: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is down: Static peer configured R2(config-router)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1(config-router)#nei 180.40.7.65 s 0/0.2 R1(config-router)#^Z R1# *Mar 1 15:40:23.605: %SYS-5-CONFIG_I: Configured from console by console R1# R1# R1# R1# R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 11 00:01:49 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 13 00:01:52 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 12 00:01:53 3 200 0 2 R1#p 180.40.7.66 5 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R1# R1# R1#p 180.40.7.65sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 14 00:02:04 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 10 00:02:12 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 14 00:02:13 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 12 00:02:15 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 12 00:02:16 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 11 00:02:16 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 11 00:02:16 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 11 00:02:17 3 200 0 2 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 10 00:02:17 3 200 0 2 R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] * R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 180.40.7.66 Se1/0.2 12 00:00:36 1 5000 0 4 1 208.28.1.130 Fa0/1 12 00:01:35 4 200 0 3 R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# RACK13AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.65 Se0/0.2 169 00:00:13 1 3000 0 5 0 208.28.1.65 Et0/0 10 00:02:31 3 200 0 2 R1# R1# R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 4 subnets, 3 masks D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:02:38, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/28 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:00:19, Null0 180.40.0.0/16 is variably subnetted, 2 subnets, 2 masks D 180.40.0.0/16 is a summary, 00:02:23, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# RACK13AS>5 [Resuming connection 5 to r5 ... ] 15:4 S5(config-router)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.128/27 is directly connected, Vlan20 C 208.28.1.64/28 is directly connected, Vlan10 D 180.40.0.0/16 [90/2170112] via 208.28.1.66, 00:02:40, Vlan10 S5(config-router)#^Z S5# 15:43:55: %SYS-5-CONFIG_I: Configured from console by console S5# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b router router eigrp 100 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! no ip http server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! --More-- RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#^Z R2#sh run | *Mar 1 15:41:34.521: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b 1/0.2 interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown --More--  ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router eigrp 100 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! --More-- RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#sh run \ b     | b rotuer S5#sh run | b rotuer    uter router eigrp 100 network 208.28.1.65 0.0.0.0 network 208.28.1.130 0.0.0.0 auto-summary ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 no login line vty 5 15 no login ! ! --More--   S5# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#tr  router rip R3(config-router)#ver 2 R3(config-router)#no auto R3(config-router)#net 208.28.1.0 R3(config-router)#net 180.40.0; .0 R3(config-router)#deb fram pack ^ % Invalid input detected at '^' marker. R3(config-router)#deb fram packddeb fram packodeb fram pack deb fram pack Frame Relay packet debugging is on R3(config-router)# *Mar 1 15:44:16.458: Serial1/0: broadcast search *Mar 1 15:44:16.458: Serial1/0:encaps failed on broadcast for link 7(IP) R3(config-router)# *Mar 1 15:44:21.106: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 339 R3(config-router)#nei *Mar 1 15:44:45.165: Serial1/0: broadcast search *Mar 1 15:44:45.165: Serial1/0:encaps failed on broadcast for link 7(IP) R3(config-router)#nei 208.28.1.1 R3(config-router)#nei 208.28.1.1 ? R3(config-router)#nei 208.28.1.1   3 R3(config-router)# R3(config-router)# R3(config-router)# R3(config-router)# R3(config-router)# *Mar 1 15:45:12.634: Serial1/0: broadcast search *Mar 1 15:45:12.634: Serial1/0:encaps failed on broadcast for link 7(IP) *Mar 1 15:45:12.634: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 56 *Mar 1 15:45:12.634: Serial1/0(o): dlci 301(0x48D1), pkt type 0x800(IP), datagramsize 56 *Mar 1 15:45:12.670: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 60 *Mar 1 15:45:12.678: Serial1/0(i): dlci 301(0x48D1), pkt type 0x800, datagramsize 60 R3(config-router)#do u all All possible debugging has been turned off R3(config-router)# *Mar 1 15:45:21.036: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 339 R3(config-router)#^Z R3# RACK13AS>1 [Resuming connection 1 to r1 ... ]  end --More--   R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router rip R1(config-router)#ver 2 R1(config-router)#no auto R1(config-router)#net     pass R1(config-router)#passive-interface e 0/0 R1(config-router)#net 208.28.1.0 R1(config-router)#^Z R1# *Mar 1 15:47:31.683: %SYS-5-CONFIG_I: Configured from console by console R1# RACK13AS>2 [Resuming connection 2 to r2 ... ]  ! --More--   R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#ver 2 R2(config-router)#no auto R2(config-router)#pass fa 0/1 R2(config-router)#pass s 1/0.2 R2(config-router)#net 208.28.1.0 R2(config-router)#net 180.40.0.0 R2(config-router)#nei 208.28.1. RACK13AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip rout Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:01, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.0 is directly connected, Serial1/2 R 180.40.7.64 [120/1] via 180.40.7.2, 00:00:20, Serial1/2 R3# R3# R3#sh ip rout Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:22, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:01, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.0 is directly connected, Serial1/2 R 180.40.7.64 [120/1] via 180.40.7.2, 00:00:22, Serial1/2 R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] 2 R2(config-router)#nei 208.28.1.2              ^Z R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip rout Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:24, Serial1/2 [120/1] via 208.28.1.3, 00:00:04, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:06, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.0 is directly connected, Serial1/2 R 180.40.7.64 [120/1] via 180.40.7.2, 00:00:25, Serial1/2 [120/1] via 208.28.1.3, 00:00:05, Serial1/0 R3#p 208.28.1.65 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router rip R1(config-router)#red R1(config-router)#redistribute ei R1(config-router)#redistribute eigrp 100 ? metric Metric for redistributed routes route-map Route map reference R1(config-router)#redistribute eigrp 100 me R1(config-router)#redistribute eigrp 100 metric 3 R1(config-router)#router eigrp 100 R1(config-router)#red R1(config-router)#redistribute rip me R1(config-router)#redistribute rip metric ? <1-4294967295> Bandwidth metric in Kbits per second R1(config-router)#redistribute rip metric 128 ? <0-4294967295> EIGRP delay metric, in 10 microsecond units R1(config-router)#redistribute rip metric 128 2000 ? <0-255> EIGRP reliability metric where 255 is 100% reliable R1(config-router)#redistribute rip metric 128 2000 25  5 1 ? <1-255> EIGRP Effective bandwidth metric (Loading) where 255 is 100% loaded R1(config-router)#redistribute rip metric 128 2000 255 1 1500 R1(config-router)#^Z R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eigrp 100 R2(config-router)#redistribute rip metric 128 2000 255 1 1500 R2(config-router)#router eip   rip R2(config-router)#redi eigrp 100 met 3 R2(config-router)#^Z R2# *Mar 1 15:52:39.819: %SYS-5 RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip rotue ^ % Invalid input detected at '^' marker. R3#sh ip rotue ^ % Invalid input detected at '^' marker. R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 5 subnets, 4 masks R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:10, Serial1/2 [120/1] via 208.28.1.3, 00:00:22, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:25, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/28 [120/3] via 180.40.7.2, 00:00:10, Serial1/2 [120/3] via 208.28.1.3, 00:00:12, Serial1/0 R 208.28.1.0/24 [120/3] via 208.28.1.1, 00:00:00, Serial1/0 [120/3] via 180.40.7.2, 00:00:11, Serial1/2 [120/3] via 208.28.1.3, 00:00:12, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks --More--  C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/3] via 208.28.1.1, 00:00:00, Serial1/0 [120/3] via 180.40.7.2, 00:00:12, Serial1/2 [120/3] via 208.28.1.3, 00:00:12, Serial1/0 R 180.40.7.64/27 [120/1] via 180.40.7.2, 00:00:12, Serial1/2 [120/1] via 208.28.1.3, 00:00:24, Serial1/0 R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] G_I: Configured from R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 5 subnets, 4 masks C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:16:06, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D EX 208.28.1.0/28 [170/20514816] via 208.28.1.130, 00:02:09, FastEthernet0/1 D 208.28.1.0/24 is a summary, 00:14:39, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:16:08, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 4 subnets, 3 masks C 208.28.1.128/27 is directly connected, Vlan20 C 208.28.1.64/28 is directly connected, Vlan10 D EX 208.28.1.0/29 [170/20512256] via 208.28.1.129, 00:02:07, Vlan20 D EX 208.28.1.0/28 [170/20512256] via 208.28.1.66, 00:02:25, Vlan10 D 180.40.0.0/16 [90/2170112] via 208.28.1.66, 00:16:24, Vlan10 S5# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 5 subnets, 4 masks D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:17:22, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 D EX 208.28.1.0/29 [170/20537856] via 208.28.1.65, 00:02:19, Ethernet0/0 C 208.28.1.0/28 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:15:03, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:02:24, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:17:06, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 1/  0/0.1 R1(config-subif)#ip add 208.28.1.1 255.255.255.248 R1(config-subif)#^Z R1# *Mar 1 15:57:01.445: %SYS-5-CONFIG_I: Configured from console by console R1#confi tsh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:18:22, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:16:03, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 is possibly down, routing via 208.28.1.2, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:18:07, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:28, Serial1/2 [120/1] via 208.28.1.3, 00:00:06, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:15, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/3] via 208.28.1.1, 00:00:15, Serial1/0 [120/3] via 180.40.7.2, 00:00:00, Serial1/2 [120/3] via 208.28.1.3, 00:00:08, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/3] via 208.28.1.1, 00:00:16, Serial1/0 --More--   R3#p sh ip routetuep 208.28.1.65sh ip rout p 208.28.1.65 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/61 ms R3#p 208.28.1.65 6 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/74/92 ms R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:20:18, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:17:59, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:10, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:20:03, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#p 208.28.1.665sh ip route  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:21, Serial1/2 [120/1] via 208.28.1.3, 00:00:29, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:05, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/3] via 208.28.1.1, 00:00:05, Serial1/0 [120/3] via 180.40.7.2, 00:00:22, Serial1/2 [120/3] via 208.28.1.3, 00:00:00, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/3] via 208.28.1.1, 00:00:06, Serial1/0 --More--   [120/3] via 180.40.7.2, 00:00:22, Serial1/2 [120/3] via 208.28.1.3, 00:00:00, Serial1/0 R 180.40.7.64/27 [120/1] via 180.40.7.2, 00:00:22, Serial1/2 [120/1] via 208.28.1.3, 00:00:00, Serial1/0 R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:20:53, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:19:25, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:20:53, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 3 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! --More--   R2#deb ip rip RIP protocol debugging is on R2# *Mar 1 15:59:36.851: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 15:59:36.851: RIP: build update entries *Mar 1 15:59:36.851: 180.40.0.0/16 via 0.0.0.0, metric 3, tag 0 *Mar 1 15:59:36.851: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 15:59:36.851: 208.28.1.0/24 via 0.0.0.0, metric 3, tag 0 *Mar 1 15:59:36.851: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 15:59:36.851: 208.28.1.64/28 via 0.0.0.0, metric 3, tag 0 *Mar 1 15:59:36.855: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 R2# *Mar 1 15:59:54.444: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 15:59:54.444: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 15:59:54.444: 208.28.1.64/28 via 0.0.0.0 in 2 hops R2# *Mar 1 15:59:56.319: RIP: received v2 update from 208.28.1.2 on Serial1/0.1 *Mar 1 15:59:56.319: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 15:59:56.595: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 15:59:56.595: RIP: build update entries *Mar 1 15:59:56.595: 180.40.0.0/16 via 0.0.0.0, metric 3, tag 0 *Mar 1 15:59:56.595: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 15:59:56.595: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 15:59:56.595: 208.28.1.0/24 via 0.0.0.0, metric 3, tag 0 *Mar 1 15:59:56.595: 208.28.1.64/28 via 0.0.0.0, metric 3, tag 0 *Mar 1 15:59:56.599: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 R2# *Mar 1 15:59:56.599: RIP: sending v2 update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 15:59:56.599: RIP: build update entries *Mar 1 15:59:56.599: 180.40.0.0/16 via 0.0.0.0, metric 3, tag 0 *Mar 1 15:59:56.599: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 15:59:56.599: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 15:59:56.599: 208.28.1.0/24 via 0.0.0.0, metric 3, tag 0 *Mar 1 15:59:56.603: 208.28.1.64/28 via 0.0.0.0, metric 3, tag 0 *Mar 1 15:59:56.603: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 R2#u all All possible debugging has been turned off R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:02, Serial1/2 [120/1] via 208.28.1.3, 00:00:09, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:12, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/3] via 208.28.1.1, 00:00:12, Serial1/0 [120/3] via 180.40.7.2, 00:00:04, Serial1/2 [120/3] via 208.28.1.3, 00:00:10, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/3] via 208.28.1.1, 00:00:13, Serial1/0 --More--   R3#sh ip rip data 180.40.0.0/16 auto-summary 180.40.0.0/16 [3] via 208.28.1.3, 00:00:19, Serial1/0 [3] via 180.40.7.2, 00:00:17, Serial1/2 [3] via 208.28.1.1, 00:00:20, Serial1/0 180.40.7.0/27 directly connected, Serial1/2 180.40.7.64/27 [1] via 208.28.1.3, 00:00:19, Serial1/0 [1] via 180.40.7.2, 00:00:17, Serial1/2 208.28.1.0/24 auto-summary 208.28.1.0/24 [3] via 208.28.1.3, 00:00:19, Serial1/0 [3] via 180.40.7.2, 00:00:17, Serial1/2 [3] via 208.28.1.1, 00:00:20, Serial1/0 208.28.1.0/29 directly connected, Serial1/0 208.28.1.64/28 [1] via 208.28.1.1, 00:00:20, Serial1/0 208.28.1.128/27 [1] via 208.28.1.3, 00:00:19, Serial1/0 [1] via 180.40.7.2, 00:00:17, Serial1/2 R3# R3# R3# R3# R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 3 passive-interface Ethernet0/0 network 208.28.1.0 no auto-summary ! no ip http server ip classless ! ! ! ! ! ! ! --More-- RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh rn |      run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 3 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! --More-- RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b router router rip version 2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! line con 0 --More--   R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 12/  /2 R3(config-if)#exit R3(config)#key ch R3(config)#key chain Prob4 R3(config-keychain)#key 1 R3(config-keychain-key)#k R3(config-keychain-key)#key-string cisco R3(config-keychain-key)#int s 1/2 R3(config-if)#ip rip auth R3(config-if)#ip rip authentication ? key-chain Authentication key-chain mode Authentication mode R3(config-if)#ip rip authentication l k R3(config-if)#ip rip authentication key-chain ? LINE name of key-chain R3(config-if)#ip rip authentication key-chain Prob4 R3(config-if)#ip rip authentication key-chain Prob4               mo R3(config-if)#ip rip authentication mode ? md5 Keyed message digest text Clear text authentication R3(config-if)#ip rip authentication mode md5 R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ]  ! --More--   R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#key R2(config)#key ch R2(config)#key chain Prob4 R2(config-keychain)#ke R2(config-keychain)#key 1 R2(config-keychain-key)#ke R2(config-keychain-key)#key-string cisco R2(config-keychain-key)#key-string cisco     ? 0 Specifies an UNENCRYPTED password will follow 7 Specifies a HIDDEN password will follow LINE The UNENCRYPTED (cleartext) user password R2(config-keychain-key)#key-string 7 cisco Invalid encrypted keystring: cisco R2(config-keychain-key)#key-string 7 cisco     ? WORD The HIDDEN user password string R2(config-keychain-key)#key-string 7              exit R2(config-keychain)#exit R2(config)#seriv  vic R2(config)#service pass R2(config)#service password-encryption R2(config)#do sh run | b l key key chain Prob4 key 1 key-string 7 060506324F41 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   R2(config)#do sh fram map Serial1/0.2 (up): ip 180.40.7.66 dlci 201(0xC9,0x3090), static, CISCO, status defined, active Serial1/0.1 (up): ip 208.28.1.1 dlci 203(0xCB,0x30B0), static, CISCO, status defined, active Serial1/0.1 (up): ip 208.28.1.2 dlci 203(0xCB,0x30B0), static, CISCO, status defined, active R2(config)#do sh fram map int s 12 /2 R2(config-if)#ip rip authen k R2(config-if)#ip rip authen key-chain Prob4 R2(config-if)#ip rip authen key-chain Prob4               mode m R2(config-if)#ip rip authen mode md5 R2(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#no shut R3(config-if)#do deb ip rip RIP protocol debugging is on R3(config-if)# *Mar 1 16:12:32.414: RIP: received v2 update from 208.28.1.1 on Serial1/0 *Mar 1 16:12:32.414: 180.40.0.0/16 via 0.0.0.0 in 3 hops *Mar 1 16:12:32.414: 180.40.7.64/27 via 0.0.0.0 in 3 hops *Mar 1 16:12:32.414: 208.28.1.0/24 via 0.0.0.0 in 3 hops *Mar 1 16:12:32.418: 208.28.1.64/28 via 0.0.0.0 in 1 hops *Mar 1 16:12:32.418: 208.28.1.128/27 via 0.0.0.0 in 3 hops R3(config-if)# *Mar 1 16:12:34.281: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.3) *Mar 1 16:12:34.281: RIP: build update entries *Mar 1 16:12:34.281: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:12:34.281: 180.40.7.64/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 16:12:34.281: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:12:34.281: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:34.281: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 *Mar 1 16:12:34.285: 208.28.1.128/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 16:12:34.746: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 16:12:34.746: 180.40.0.0/16 via 0.0.0.0 in 3 hops R3(config-if)# *Mar 1 16:12:34.746: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 16:12:34.746: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 16:12:34.750: 208.28.1.0/24 via 0.0.0.0 in 3 hops *Mar 1 16:12:34.750: 208.28.1.64/28 via 0.0.0.0 in 3 hops *Mar 1 16:12:34.750: 208.28.1.128/27 via 0.0.0.0 in 1 hops R3(config-if)# *Mar 1 16:12:37.879: RIP: received packet with MD5 authentication *Mar 1 16:12:37.879: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 16:12:37.879: 180.40.0.0/16 via 0.0.0.0 in 3 hops *Mar 1 16:12:37.879: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 16:12:37.883: 208.28.1.0/24 via 0.0.0.0 in 3 hops *Mar 1 16:12:37.883: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 16:12:37.883: 208.28.1.64/28 via 0.0.0.0 in 3 hops *Mar 1 16:12:37.883: 208.28.1.128/27 via 0.0.0.0 in 1 hops R3(config-if)# *Mar 1 16:12:42.651: RIP: sending v2 update to 224.0.0.9 via Serial1/0 (208.28.1.2) *Mar 1 16:12:42.651: RIP: build update entries *Mar 1 16:12:42.651: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:42.651: RIP: sending v2 update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 16:12:42.651: RIP: build update entries *Mar 1 16:12:42.651: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:42.651: RIP: sending v2 update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 16:12:42.655: RIP: build update entries *Mar 1 16:12:42.655: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#^Z R2#de *Mar 1 16:12:47.884: %SYS-5-CONFIG_I: Configured from console by console R2#deb ip rip RIP protocol debugging is on R2# *Mar 1 16:12:54.511: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 16:12:54.511: RIP: build update entries *Mar 1 16:12:54.511: 180.40.0.0/16 via 0.0.0.0, metric 3, tag 0 *Mar 1 16:12:54.511: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:54.511: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:54.511: 208.28.1.0/24 via 0.0.0.0, metric 3, tag 0 *Mar 1 16:12:54.511: 208.28.1.64/28 via 0.0.0.0, metric 3, tag 0 *Mar 1 16:12:54.515: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:54.515: RIP: sending v2 update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 16:12:54.515: RIP: build update entries R2# *Mar 1 16:12:54.515: 180.40.0.0/16 via 0.0.0.0, metric 3, tag 0 *Mar 1 16:12:54.515: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:54.515: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:54.515: 208.28.1.0/24 via 0.0.0.0, metric 3, tag 0 *Mar 1 16:12:54.519: 208.28.1.64/28 via 0.0.0.0, metric 3, tag 0 *Mar 1 16:12:54.519: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 R2# *Mar 1 16:12:57.592: RIP: received packet with MD5 authentication *Mar 1 16:12:57.592: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 16:12:57.596: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 16:12:57.596: 208.28.1.64/28 via 0.0.0.0 in 2 hops R2# *Mar 1 16:12:58.874: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 16:12:58.874: RIP: build update entries *Mar 1 16:12:58.874: 180.40.0.0/16 via 0.0.0.0, metric 3, tag 0 *Mar 1 16:12:58.874: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:58.874: 208.28.1.0/24 via 0.0.0.0, metric 3, tag 0 *Mar 1 16:12:58.874: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:12:58.874: 208.28.1.64/28 via 0.0.0.0, metric 3, tag 0 *Mar 1 16:12:58.878: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 R2#u all All possible debugging has been turned off R2#sh run | b K key key chain Prob4 key 1 key-string 7 060506324F41 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 ! --More--  interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip rip authentication mode md5 ip rip authentication key-chain Prob4 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 --More-- RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-if)#^Z R3#sh run *Mar 1 16:15:29.977: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b key *Mar 1 16:15:33.832: RIP: sending v2 update to 224.0.0.9 via Serial1/0 (208.28.1.2) *Mar 1 16:15:33.832: RIP: build update entries *Mar 1 16:15:33.832: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:15:33.832: RIP: sending v2 update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 16:15:33.832: RIP: build update entries *Mar 1 16:15:33.832: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:15:33.836: RIP: sending v2 update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 16:15:33.836: RIP: build update entries *Mar 1 16:15:33.836: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0key chain Prob4 key 1 key-string cisco ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   R3#u alk  a ll All possible debugging has been turned off R3#u allsh run | b key key chain Prob4 key 1 key-string cisco ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 --More--   no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown --More--  ! --More--  interface Serial1/7 --More--   no ip address --More-- RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int lo 0 S5(config-if)#ip add 208.28 16:20:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up S5(config-if)#ip add 208.28.1.193 255.255.255.255 S5(config-if)#ip add 208.28.1.193 255.255.255.255nt lo 0 do sh ip routeint lo 0  1 S5(config-if)#int lo 1p add 208.28.1.193 255.255.255.2553 16:20:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up S5(config-if)#ip add 208.28.1.193 255.255.255.255 255.255.255.255 4 255.255.255.255 S5(config-if)#router e eigrp 100 S5(config-router)#redis S5(config-router)#redistribute con S5(config-router)#redistribute connected S5(config-router)# RACK13AS>2 [Resuming connection 2 to r2 ... ]   no ip address --More--   R2#sh pi  ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/156160] via 208.28.1.130, 00:00:08, FastEthernet0/1 D EX 208.28.1.194/32 [170/156160] via 208.28.1.130, 00:00:08, FastEthernet0/1 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:40:22, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:38:55, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:40:23, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#q sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/156160] via 208.28.1.130, 00:00:15, FastEthernet0/1 D EX 208.28.1.194/32 [170/156160] via 208.28.1.130, 00:00:15, FastEthernet0/1 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:40:29, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:39:02, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:40:30, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/156160] via 208.28.1.130, 00:00:18, FastEthernet0/1 D EX 208.28.1.194/32 [170/156160] via 208.28.1.130, 00:00:18, FastEthernet0/1 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:40:32, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:39:04, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:40:33, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2# RACK13AS>2 1 [Resuming connection 1 to r1 ... ]  ! --More--   R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/409600] via 208.28.1.65, 00:00:24, Ethernet0/0 D EX 208.28.1.194/32 [170/409600] via 208.28.1.65, 00:00:24, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:41:26, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:39:08, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:13, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:41:11, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# R1# R1# RACK13AS>3 [Resuming connection 3 to r3 ... ]   shutdown --More--   R3#q sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/3] via 180.40.7.2, 00:00:26, Serial1/2 [120/3] via 208.28.1.3, 00:00:02, Serial1/0 [120/3] via 208.28.1.1, 00:00:08, Serial1/0 R 208.28.1.194/32 [120/3] via 180.40.7.2, 00:00:26, Serial1/2 [120/3] via 208.28.1.3, 00:00:02, Serial1/0 [120/3] via 208.28.1.1, 00:00:09, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:03, Serial1/0 [120/1] via 180.40.7.2, 00:00:00, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:09, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 --More--  R 208.28.1.0/24 [120/3] via 208.28.1.1, 00:00:19, Serial1/0 --More--   [120/3] via 208.28.1.3, 00:00:13, Serial1/0 --More--   [120/3] via 180.40.7.2, 00:00:10, Serial1/2 --More--   R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/409600] via 208.28.1.65, 00:00:51, Ethernet0/0 D EX 208.28.1.194/32 [170/409600] via 208.28.1.65, 00:00:51, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:41:54, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:39:36, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:11, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:41:39, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/156160] via 208.28.1.130, 00:00:55, FastEthernet0/1 D EX 208.28.1.194/32 [170/156160] via 208.28.1.130, 00:00:55, FastEthernet0/1 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:41:09, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:39:42, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:41:10, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#q sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/156160] via 208.28.1.130, 00:01:01, FastEthernet0/1 D EX 208.28.1.194/32 [170/156160] via 208.28.1.130, 00:01:01, FastEthernet0/1 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:41:15, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:39:48, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:41:16, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/409600] via 208.28.1.65, 00:01:06, Ethernet0/0 D EX 208.28.1.194/32 [170/409600] via 208.28.1.65, 00:01:06, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:42:08, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:39:51, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:26, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:41:53, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#access-list 1 per 208.28.1.193 R1(config)#in  router ospf 1 R1(config-router)#router ospf 1nrouter ospf 1orouter ospf 1 router ospf 1 R1(config)#router rip R1(config-router)#r do sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 3 passive-interface Ethernet0/0 network 208.28.1.0 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 ! ! ! ! --More--   R1(config-router)# redistribute eigrp 100 metric 3 4 R1(config-router)#off R1(config-router)#offset-list ? <0-99> Access list of networks to apply offset (0 selects all networks) <1300-1999> Access list of networks to apply offset (expanded range) WORD Access-list name R1(config-router)#offset-list 1 ? in Perform offset on incoming updates out Perform offset on outgoing updates R1(config-router)#offset-list 1 out > ? <0-16> Offset R1(config-router)#offset-list 1 out 3 R1(config-router)#^Z R1#deb ip *Mar 1 16:22:53.805: %SYS-5-CONFIG_I: Configured from console by console R1#deb ip rip RIP protocol debugging is on R1#u all *Mar 1 16:23:12.420: RIP: received v2 update from 208.28.1.2 on Serial0/0.1 *Mar 1 16:23:12.420: 180.40.7.0/27 via 0.0.0.0 in 1 hops R1#u all *Mar 1 16:23:21.014: RIP: sending v2 update to 224.0.0.9 via Serial0/0.1 (208.28.1.1) *Mar 1 16:23:21.014: RIP: build update entries *Mar 1 16:23:21.014: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:23:21.014: 180.40.7.64/27 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:23:21.014: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:23:21.014: 208.28.1.64/28 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:23:21.018: 208.28.1.128/27 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:23:21.018: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 16:23:21.018: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R1#u all All possible debugging has been turned off R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/3] via 180.40.7.2, 00:00:07, Serial1/2 [120/3] via 208.28.1.3, 00:00:15, Serial1/0 R 208.28.1.194/32 [120/3] via 180.40.7.2, 00:00:07, Serial1/2 [120/3] via 208.28.1.3, 00:00:15, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:15, Serial1/0 [120/1] via 180.40.7.2, 00:00:08, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:23, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/3] via 208.28.1.3, 00:00:16, Serial1/0 [120/3] via 180.40.7.2, 00:00:08, Serial1/2 --More--   R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#access-list 1 per 208.28.1.193 R2(config)#route-map Prob5 R2(config-route-map)#match ip add 1 R2(config-route-map)#set me R2(config-route-map)#set metric 7 R2(config-route-map)#set metric 7match ip add 1route-map Prob5 20 R2(config-route-map)#met R2(config-route-map)#metr    set me R2(config-route-map)#set metric 4 R2(config-route-map)#router rip R2(config-router)#red d eigrp 100 rou R2(config-router)#red eigrp 100 route-map Prob5 R2(config-router)#^Z R2# *Mar 1 16:23:49.568: %SYS-5-CONFIG_I: Configured from console by console R2#deb ip rip RIP protocol debugging is on R2# *Mar 1 16:23:55.214: RIP: received packet with MD5 authentication *Mar 1 16:23:55.214: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 16:23:55.214: 208.28.1.193/32 via 0.0.0.0 in 10 hops *Mar 1 16:23:55.214: 208.28.1.194/32 via 0.0.0.0 in 7 hops R2# *Mar 1 16:23:57.217: RIP: sending v2 flash update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 16:23:57.217: RIP: build flash update entries *Mar 1 16:23:57.217: 208.28.1.193/32 via 0.0.0.0, metric 11, tag 0 *Mar 1 16:23:57.217: 208.28.1.194/32 via 0.0.0.0, metric 8, tag 0 *Mar 1 16:23:57.217: RIP: sending v2 flash update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 16:23:57.221: RIP: build flash update entries *Mar 1 16:23:57.221: 208.28.1.193/32 via 0.0.0.0, metric 11, tag 0 *Mar 1 16:23:57.221: 208.28.1.194/32 via 0.0.0.0, metric 8, tag 0 *Mar 1 16:23:57.221: RIP: sending v2 flash update to 224.0.0.9 via Serial1/2 (180.40.7.2) R2# *Mar 1 16:23:57.221: RIP: build flash update entries - suppressing null update R2# *Mar 1 16:23:59.268: RIP: received packet with MD5 authentication *Mar 1 16:23:59.272: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 16:23:59.272: 208.28.1.193/32 via 0.0.0.0 in 12 hops *Mar 1 16:23:59.272: 208.28.1.194/32 via 0.0.0.0 in 9 hops R2# *Mar 1 16:24:01.276: RIP: sending v2 flash update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 16:24:01.276: RIP: build flash update entries *Mar 1 16:24:01.276: 208.28.1.193/32 via 0.0.0.0, metric 13, tag 0 *Mar 1 16:24:01.276: 208.28.1.194/32 via 0.0.0.0, metric 10, tag 0 *Mar 1 16:24:01.276: RIP: sending v2 flash update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 16:24:01.276: RIP: build flash update entries *Mar 1 16:24:01.276: 208.28.1.193/32 via 0.0.0.0, metric 13, tag 0 *Mar 1 16:24:01.280: 208.28.1.194/32 via 0.0.0.0, metric 10, tag 0 *Mar 1 16:24:01.280: RIP: sending v2 flash update to 224.0.0.9 via Serial1/2 (180.40.7.2) R2# *Mar 1 16:24:01.280: RIP: build flash update entries - suppressing null update *Mar 1 16:24:01.965: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 16:24:01.965: RIP: build update entries *Mar 1 16:24:01.965: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:24:01.965: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:24:01.965: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:24:01.965: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:24:01.965: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:24:01.969: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:24:01.969: 208.28.1.193/32 via 0.0.0.0, metric 13, tag 0 *Mar 1 16:24:01.969: 208.28.1.194/32 via 0.0.0.0, metric 10, tag 0 *Mar 1 16:24:01.969: RIP: sending v2 update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 16:24:01.969: RIP: build update entries *Mar 1 16:24:01.969: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:24:01.969: 180.4 R2#0.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:24:01.973: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:24:01.973: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:24:01.973: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:24:01.973: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:24:01.973: 208.28.1.193/32 via 0.0.0.0, metric 13, tag 0 *Mar 1 16:24:01.973: 208.28.1.194/32 via 0.0.0.0, metric 10, tag 0 *Mar 1 16:24:02.113: RIP: received packet with MD5 authentication *Mar 1 16:24:02.117: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 16:24:02.117: 208.28.1.193/32 via 0.0.0.0 in 8 hops *Mar 1 16:24:02.117: 208.28.1.194/32 via 0.0.0.0 in 5 hops R2# *Mar 1 16:24:03.479: RIP: received packet with MD5 authentication *Mar 1 16:24:03.479: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 16:24:03.479: 180.40.0.0/16 via 0.0.0.0 in 5 hops *Mar 1 16:24:03.479: 208.28.1.0/24 via 0.0.0.0 in 5 hops *Mar 1 16:24:03.479: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 16:24:03.483: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 16:24:03.483: 208.28.1.193/32 via 0.0.0.0 in 8 hops *Mar 1 16:24:03.483: 208.28.1.194/32 via 0.0.0.0 in 5 hops *Mar 1 16:24:04.120: RIP: sending v2 flash update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 16:24:04.120: RIP: build flash update entries R2# *Mar 1 16:24:04.120: 208.28.1.193/32 via 0.0.0.0, metric 9, tag 0 *Mar 1 16:24:04.120: 208.28.1.194/32 via 0.0.0.0, metric 6, tag 0 *Mar 1 16:24:04.120: RIP: sending v2 flash update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 16:24:04.120: RIP: build flash update entries *Mar 1 16:24:04.120: 208.28.1.193/32 via 0.0.0.0, metric 9, tag 0 *Mar 1 16:24:04.124: 208.28.1.194/32 via 0.0.0.0, metric 6, tag 0 *Mar 1 16:24:04.124: RIP: sending v2 flash update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 16:24:04.124: RIP: build flash update entries - suppressing null update R2#u all All possible debugging has been turned off R2#sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 3 route-map Prob5 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 1 permit 208.28.1.193 --More--  ! route-map Prob5 permit 10 match ip address 1 set metric 7 ! route-map Prob5 permit 20 set metric 4 ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! --More--   R2#deb ip rip RIP protocol debugging is on R2# *Mar 1 16:25:23.931: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 16:25:23.931: RIP: build update entries *Mar 1 16:25:23.931: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:23.931: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:23.931: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:23.931: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:23.931: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:23.935: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:23.935: 208.28.1.193/32 via 0.0.0.0, metric 9, tag 0 *Mar 1 16:25:23.935: 208.28.1.194/32 via 0.0.0.0, metric 6, tag 0 R2# *Mar 1 16:25:23.935: RIP: sending v2 update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 16:25:23.935: RIP: build update entries *Mar 1 16:25:23.935: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:23.935: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:23.939: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:23.939: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:23.939: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:23.939: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:23.939: 208.28.1.193/32 via 0.0.0.0, metric 9, tag 0 *Mar 1 16:25:23.939: 208.28.1.194/32 via 0.0.0.0, metric 6, tag 0 R2# *Mar 1 16:25:25.806: RIP: received packet with MD5 authentication *Mar 1 16:25:25.806: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 16:25:25.806: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 16:25:25.806: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 16:25:25.806: 208.28.1.193/32 via 0.0.0.0 in 8 hops *Mar 1 16:25:25.806: 208.28.1.194/32 via 0.0.0.0 in 5 hops R2# *Mar 1 16:25:35.702: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 16:25:35.702: RIP: build update entries *Mar 1 16:25:35.702: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:35.702: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:35.702: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:35.702: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:35.702: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:35.706: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:36.628: RIP: received v2 update from 208.28.1.2 on Serial1/0.1 *Mar 1 16:25:36.628: 180.40.7.0/27 via 0.0.0.0 in 1 hops R2# *Mar 1 16:25:52.875: RIP: received packet with MD5 authentication *Mar 1 16:25:52.875: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 16:25:52.875: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 16:25:52.875: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 16:25:52.875: 208.28.1.193/32 via 0.0.0.0 in 8 hops *Mar 1 16:25:52.875: 208.28.1.194/32 via 0.0.0.0 in 5 hops *Mar 1 16:25:53.155: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 16:25:53.155: RIP: build update entries *Mar 1 16:25:53.155: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:53.155: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:53.155: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:53.155: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:53.155: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:53.159: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:53.159: 208.28.1.193/32 via 0.0.0. R2#0, metric 9, tag 0 *Mar 1 16:25:53.159: 208.28.1.194/32 via 0.0.0.0, metric 6, tag 0 *Mar 1 16:25:53.159: RIP: sending v2 update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 16:25:53.159: RIP: build update entries *Mar 1 16:25:53.159: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:53.159: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:53.163: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:53.163: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:53.163: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:25:53.163: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:25:53.163: 208.28.1.193/32 via 0.0.0.0, metric 9, tag 0 *Mar 1 16:25:53.163: 208.28.1.194/32 via 0.0.0.0, metric 6, tag 0 R2#u all All possible debugging has been turned off R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#router riped eigrp 100 route-map Prob5                   0nred eigrp 100ored eigrp 100 red eigrp 100 R2(config-router)#do sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 1 permit 208.28.1.193 ! --More--   R2(config-router)#[A  do sh run | b routerno red eigrp 100 router rip ed eigrp 100 route-map Prob5 R2(config-router)#red eigrp 100 route-map Prob5  red eigrp 100 route-map Prob5 do sh run | b router  router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 route-map Prob5 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 1 permit 208.28.1.193 --More--   R2(config-router)#do sh run | b routerred eigrp 100 route-map Prob5 do sh run | b router o R2(config-router)#do sh run | b routero   red eigrp 100 route-map Prob5 nred eigrp 100 route-map Prob5 ored eigrp 100 route-map Prob5  red eigrp 100 route-map Prob5  R2(config-router)#no red eigrp 100 route-map Prob5 do sh run | b routero   router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 1 permit 208.28.1.193 ! --More--  route-map Prob5 permit 10 --More--   R2(config-router)#do sh run | b routerno red eigrp 100 route-map Prob5 do sh run | b routero  red eigrp 100 route-map Prob5 R2(config-router)#^Z R2# *Mar 1 16:28:55.097: %SYS-5-CONFIG_I: Configured from console by console R2#deb ip rip RIP protocol debugging is on R2# *Mar 1 16:29:06.492: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 16:29:06.492: RIP: build update entries *Mar 1 16:29:06.492: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:29:06.492: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:29:06.492: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:29:06.492: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:29:06.492: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:29:06.496: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:29:06.496: 208.28.1.193/32 via 0.0.0.0, metric 9, tag 0 *Mar 1 16:29:06.496: 208.28.1.194/32 via 0.0.0.0, metric 6, tag 0 R2# *Mar 1 16:29:06.496: RIP: sending v2 update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 16:29:06.496: RIP: build update entries *Mar 1 16:29:06.496: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:29:06.496: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:29:06.500: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:29:06.500: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:29:06.500: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:29:06.500: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:29:06.500: 208.28.1.193/32 via 0.0.0.0, metric 9, tag 0 *Mar 1 16:29:06.500: 208.28.1.194/32 via 0.0.0.0, metric 6, tag 0 R2# *Mar 1 16:29:09.533: RIP: received packet with MD5 authentication *Mar 1 16:29:09.533: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 16:29:09.533: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 16:29:09.533: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 16:29:09.533: 208.28.1.193/32 via 0.0.0.0 in 8 hops *Mar 1 16:29:09.533: 208.28.1.194/32 via 0.0.0.0 in 5 hops R2# *Mar 1 16:29:21.384: RIP: received v2 update from 208.28.1.2 on Serial1/0.1 *Mar 1 16:29:21.384: 180.40.7.0/27 via 0.0.0.0 in 1 hops R2# *Mar 1 16:29:24.065: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 16:29:24.065: RIP: build update entries *Mar 1 16:29:24.065: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:29:24.065: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:29:24.065: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:29:24.065: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:29:24.065: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:29:24.069: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 R2#u all All possible debugging has been turned off R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:22, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:22, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:51:20, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:49:53, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:51:21, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/409600] via 208.28.1.65, 00:09:25, Ethernet0/0 D EX 208.28.1.194/32 [170/409600] via 208.28.1.65, 00:09:25, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:09:25, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:09:27, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:02, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:09:27, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:01, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:01, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:51:51, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:50:23, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:51:52, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.129) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 208.28.1.193/32, 1 successors, FD is 20512000, serno 19 via Redistributed (20512000/0) via 208.28.1.130 (156160/128256), FastEthernet0/1 P 208.28.1.194/32, 1 successors, FD is 20512000, serno 20 via Redistributed (20512000/0) via 208.28.1.130 (156160/128256), FastEthernet0/1 P 208.28.1.128/27, 1 successors, FD is 28160, serno 2 via Connected, FastEthernet0/1 P 208.28.1.64/28, 1 successors, FD is 28416, serno 5 via 208.28.1.130 (28416/2816), FastEthernet0/1 P 180.40.7.0/27, 1 successors, FD is 20512000, serno 8 via Redistributed (20512000/0) via 180.40.7.66 (21024000/20512000), Serial1/0.2 P 180.40.0.0/16, 1 successors, FD is 20512000, serno 3 via Summary (20512000/0), Null0 via 208.28.1.130 (2172672/2170112), FastEthernet0/1 P 208.28.1.0/29, 1 successors, FD is 20512000, serno 7 via Redistributed (20512000/0) --More--   R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#access-list 2 per 208.28,.1.    .1.193 R2(config)#access-list 2 per 208.28.1.193 3 4 R2(config)#router rip R2(config-router)#dist R2(config-router)#distan R2(config-router)#distance 18 90 ? A.B.C.D IP Source address R2(config-router)#distance 190 0.0.0.0 255.25.255    5.255.255 ? <1-99> IP Standard access list number <1300-1999> IP Standard expanded access list number WORD Standard access-list name R2(config-router)#distance 190 0.0.0.0 255.255.255.255 2 R2(config-router)#^Z R2#sh ip *Mar 1 16:32:02.989: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:13, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:13, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:53:53, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:52:26, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:53:54, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:24, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:24, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:54:04, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:52:37, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:54:05, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:27, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:27, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:54:07, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:52:40, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:54:09, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:30, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:30, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:54:10, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:52:43, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:54:11, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:33, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:33, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:54:13, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:52:46, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:54:14, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:36, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:36, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:54:16, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:52:48, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:54:17, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:39, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:39, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:54:18, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:52:51, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:54:20, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:44, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:44, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:54:23, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:52:56, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:54:25, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/8] via 180.40.7.3, 00:00:47, Serial1/2 R 208.28.1.194/32 [120/5] via 180.40.7.3, 00:00:47, Serial1/2 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:54:27, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:52:59, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:54:28, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#clea ip route * R2#clea ip route *sh ip route  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/156160] via 208.28.1.130, 00:00:01, FastEthernet0/1 D EX 208.28.1.194/32 [170/156160] via 208.28.1.130, 00:00:01, FastEthernet0/1 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:00:01, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:00:01, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:00:02, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2# R2# R2# R2#deb ip route      ip RIP protocol debugging is on R2#deb ip ripsh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/156160] via 208.28.1.130, 00:00:12, FastEthernet0/1 D EX 208.28.1.194/32 [170/156160] via 208.28.1.130, 00:00:12, FastEthernet0/1 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:00:12, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:00:12, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:00:13, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2# R2# R2# R2# R2# R2# *Mar 1 16:33:04.302: RIP: received v2 update from 208.28.1.2 on Serial1/0.1 *Mar 1 16:33:04.302: 180.40.7.0/27 via 0.0.0.0 in 1 hops R2# *Mar 1 16:33:09.062: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 16:33:09.062: RIP: build update entries *Mar 1 16:33:09.062: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:33:09.062: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:33:09.062: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:33:09.062: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:33:09.062: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:33:09.066: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:33:09.066: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 16:33:09.066: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2# *Mar 1 16:33:09.066: RIP: sending v2 update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 16:33:09.066: RIP: build update entries *Mar 1 16:33:09.066: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:33:09.066: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:33:09.070: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:33:09.070: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:33:09.070: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:33:09.070: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:33:09.070: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 16:33:09.070: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2# *Mar 1 16:33:13.417: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 16:33:13.417: RIP: build update entries *Mar 1 16:33:13.417: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:33:13.417: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:33:13.417: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:33:13.417: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:33:13.417: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 16:33:13.421: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 16:33:13.421: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 16:33:13.421: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2# *Mar 1 16:33:16.297: RIP: received packet with MD5 authentication *Mar 1 16:33:16.297: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 16:33:16.297: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 16:33:16.297: 208.28.1.64/28 via 0.0.0.0 in 2 hops R2#u all All possible debugging has been turned off R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/409600] via 208.28.1.65, 00:13:16, Ethernet0/0 D EX 208.28.1.194/32 [170/409600] via 208.28.1.65, 00:13:16, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:13:16, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:13:17, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:07, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:13:17, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D EX 208.28.1.193/32 [170/409600] via 208.28.1.65, 00:13:26, Ethernet0/0 D EX 208.28.1.194/32 [170/409600] via 208.28.1.65, 00:13:26, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:13:26, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:13:27, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:17, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:13:27, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#access-list 2 208.28.1.193 ^ % Invalid input detected at '^' marker. R1(config)#access-list 2 208.28.1.193p208.28.1.193e208.28.1.193r208.28.1.193 208.28.1.193 R1(config)#access-list 2 per 208.28.1.193208.28.1.193 per 208.28.1.193 4 R1(config)#router rip R1(config-router)#dista R1(config-router)#distance 190 0.0.0.0 255.255.255.255 2 R1(config-router)#^Z R1# *Mar 1 16:35:52.258: %SYS-5-CONFIG_I: Configured from console by console R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.1, 00:00:10, Serial1/0 [120/7] via 180.40.7.2, 00:00:13, Serial1/2 [120/7] via 208.28.1.3, 00:00:19, Serial1/0 R 208.28.1.194/32 [120/4] via 208.28.1.1, 00:00:10, Serial1/0 [120/4] via 180.40.7.2, 00:00:13, Serial1/2 [120/4] via 208.28.1.3, 00:00:20, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:20, Serial1/0 [120/1] via 180.40.7.2, 00:00:14, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:12, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 --More--   R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 4 passive-interface Ethernet0/0 offset-list 1 out 3 network 208.28.1.0 distance 190 0.0.0.0 255.255.255.255 2 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.193 access-list 2 permit 208.28.1.194 --More--  ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! end R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run |           RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 route-map Prob5 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 distance 190 0.0.0.0 255.255.255.255 2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! --More--  access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.193 access-list 2 permit 208.28.1.194 ! route-map Prob5 permit 10 match ip address 1 set metric 7 ! route-map Prob5 permit 20 set metric 4 ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 --More-- RACK13AS>5 [Resuming connection 5 to r5 ... ] S5(config-router)#^Z S5#sh ru n   16:39:30: %SYS-5-CONFIG_I: Configured from console by console S5#sh run | b router router eigrp 100 redistribute connected network 208.28.1.65 0.0.0.0 network 208.28.1.130 0.0.0.0 auto-summary ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 no login line vty 5 15 no login ! --More--   S5# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#ip rip tr R3(config-if)#ip rip triggered ? R3(config-if)#ip rip triggered R3(config-if)#^Z R3# RACK13AS>2 [Resuming connection 2 to r2 ... ]  line vty 0 4 --More--   R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#ip rip tr R2(config-if)#ip rip triggered R2(config-if)#^Z R2#sh ip *Mar 1 16:37:18.651: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip proto Routing Protocol is "eigrp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates Default networks accepted from incoming updates EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0 EIGRP maximum hopcount 100 EIGRP maximum metric variance 1 Redistributing: eigrp 100, rip EIGRP NSF-aware route hold timer is 240s Automatic network summarization is in effect Automatic address summarization: 208.28.1.0/24 for Serial1/0.2 Summarizing with metric 28160 180.40.0.0/16 for FastEthernet0/1 Summarizing with metric 20512000 Maximum path: 4 Routing for Networks: 180.40.7.65/32 208.28.1.129/32 Routing Information Sources: Gateway Distance Last Update (this router) 90 00:04:38 --More--   Gateway Distance Last Update 208.28.1.130 90 00:04:40 180.40.7.66 90 00:04:40 Distance: internal 90 external 170 Routing Protocol is "rip" Sending updates every 30 seconds, next due in 26 seconds Invalid after 180 seconds, hold down 0, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: eigrp 100, rip Neighbor(s): 208.28.1.2 Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial1/0.1 2 2 Serial1/2 2 2 Yes Prob4 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 180.40.0.0 208.28.1.0 Passive Interface(s): --More--   R2#sh run int s 1/2 Building configuration... Current configuration : 173 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 clock rate 64000 end R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run int s 1/2 Building configuration... Current configuration : 155 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 end R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#? Router configuration commands: address-family Enter Address Family command mode auto-summary Enable automatic network number summarization default Set a command to its defaults default-information Control distribution of default information default-metric Set metric of redistributed routes distance Define an administrative distance distribute-list Filter networks in routing updates exit Exit from routing protocol configuration mode flash-update-threshold Specify flash update threshold in second help Description of the interactive help system input-queue Specify input queue depth maximum-paths Forward packets over multiple paths neighbor Specify a neighbor router network Enable routing on an IP network no Negate a command or set its defaults offset-list Add or subtract offset from RIP metrics output-delay Interpacket delay for RIP updates passive-interface Suppress routing updates on an interface redistribute Redistribute information from another routing protocol timers Adjust routing timers --More--   traffic-share How to compute traffic share over alternate paths validate-update-source Perform sanity checks against source address of routing updates version Set routing protocol version R2(config-router)#tim R2(config-router)#timers ? basic Basic routing protocol update timers R2(config-router)#timers bas R2(config-router)#timers basic ? <0-4294967295> Interval between updates R2(config-router)#timers basic              out R2(config-router)#output-delay ? <8-50> Delay in milliseconds R2(config-router)#output-delay 10 R2(config-router)#^Z R2#sdh   *Mar 1 16:39:28.760: %SYS-5-CONFIG_I: Configured from console by console R2#sdh  h run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 timers basic 30 180 0 240 redistribute eigrp 100 route-map Prob5 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 output-delay 10 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 distance 190 0.0.0.0 255.255.255.255 2 no auto-summary ! ip classless ! no ip http server --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router rip R3(config-router)#v? validate-update-source version R3(config-router)#v no vl R3(config-router)#no vl al R3(config-router)#no validate-update-source ? R3(config-router)#no validate-update-source R3(config-router)#^Z R3# *Mar 1 16:40:27.989: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b router router rip version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! --More--   R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#route  r rip R3(config-router)#max R3(config-router)#maximum-paths 3 R3(config-router)#^Z R3# *Mar 1 16:42:44.585: %SY RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#rouer rip ^ % Invalid input detected at '^' marker. R1(config)#router rip R1(config-router)#max R1(config-router)#maximum-paths 3 R1(config-router)#^Z R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh    confi r ^ % Invalid input detected at '^' marker. R2#confi r t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#max R2(config-router)#maximum-paths 3 R2(config-router)#^Z R2#sh run *Mar 1 16:43:03.360: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b router rip router rip version 2 timers basic 30 180 0 240 redistribute eigrp 100 route-map Prob5 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 output-delay 10 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 maximum-paths 3 distance 190 0.0.0.0 255.255.255.255 2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.193 access-list 2 permit 208.28.1.194 ! --More--  route-map Prob5 permit 10 --More--   match ip address 1 --More--   R2#sh ip proto Routing Protocol is "eigrp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates Default networks accepted from incoming updates EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0 EIGRP maximum hopcount 100 EIGRP maximum metric variance 1 Redistributing: eigrp 100, rip EIGRP NSF-aware route hold timer is 240s Automatic network summarization is in effect Automatic address summarization: 208.28.1.0/24 for Serial1/0.2 Summarizing with metric 28160 180.40.0.0/16 for FastEthernet0/1 Summarizing with metric 20512000 Maximum path: 4 Routing for Networks: 180.40.7.65/32 208.28.1.129/32 Routing Information Sources: Gateway Distance Last Update (this router) 90 00:11:23 --More--   R2#sh ip proto Routing Protocol is "eigrp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates Default networks accepted from incoming updates EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0 EIGRP maximum hopcount 100 EIGRP maximum metric variance 1 Redistributing: eigrp 100, rip EIGRP NSF-aware route hold timer is 240s Automatic network summarization is in effect Automatic address summarization: 208.28.1.0/24 for Serial1/0.2 Summarizing with metric 28160 180.40.0.0/16 for FastEthernet0/1 Summarizing with metric 20512000 Maximum path: 4 Routing for Networks: 180.40.7.65/32 208.28.1.129/32 Routing Information Sources: Gateway Distance Last Update (this router) 90 00:11:26 --More--   Gateway Distance Last Update 208.28.1.130 90 00:11:27 180.40.7.66 90 00:00:59 Distance: internal 90 external 170 Routing Protocol is "rip" Sending updates every 30 seconds, next due in 21 seconds Invalid after 180 seconds, hold down 0, flushed after 240 Output delay 10 milliseconds between packets Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: eigrp 100, rip Neighbor(s): 208.28.1.2 Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial1/0.1 2 2 Serial1/2 2 2 Yes Prob4 Automatic network summarization is not in effect Maximum path: 3 Routing for Networks: 180.40.0.0 208.28.1.0 --More--   R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#touyert         router ospf 1 R1(config-router)#rout R1(config-router)#router-id 1.1.1.1 R1(config-router)#net 17.57.100.1 0.0.0.0 area 0 R1(config-router)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#rouetr     ter ospf 1 S6(config-router)#rout S6(config-router)#router-id 6,.6   .6.6.6 S6(config-router)#net 17.57.100.2 0.0.0.0 area 0 S6(config-router)#^Z S6# RACK13AS>3 [Resuming connection 3 to r3 ... ] NFIG_I: Configured f R3#conif t ^ % Invalid input detected at '^' marker. R3#rou   confi g t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router ospf ` ^ % Invalid input detected at '^' marker. R3(config)#router ospf ` 1 R3(config-router)#rout R3(config-router)#router-id 3.3.3.3.3   R3(config-router)#net 17.80.1.1 0..0.   0- .0.0 area 0 R3(config-router)#^Z R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router ospf 1 R4(config-router)#rout R4(config-router)#router-id 4.4.4.4 R4(config-router)#net 17.80.1.2 0/0.   .0.0.0 area 0 R4(config-router)#^Z R4#sh i *Mar 1 16:50:14.291: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:37 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:36 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:34 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:33 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:32 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:32 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:31 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:38 17.80.1.1 FastEthernet0/0 R4# RACK13AS>6 [Resuming connection 6 to r6 ... ] 16:50:05: %SYS-5-CONFIG_I: S6#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 1.1.1.1 1 FULL/BDR 00:00:31 17.57.100.1 Vlan16 S6# S6# S6# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:36 17.80.1.1 FastEthernet0/0 R4# *Mar 1 16:50:53.827: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 FULL/BDR 00:00:39 17.80.1.1 FastEthernet0/0 R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] *M R1(config-router)#^Z R1#sh run | b *Mar 1 16:49:49.538: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b ospf router ospf 1 router-id 1.1.1.1 log-adjacency-changes network 17.57.100.1 0.0.0.0 area 0 ! router rip version 2 redistribute eigrp 100 metric 4 passive-interface Ethernet0/0 offset-list 1 out 3 network 208.28.1.0 maximum-paths 3 distance 190 0.0.0.0 255.255.255.255 2 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.193 access-list 2 permit 208.28.1.194 ! --More-- RACK13AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run | b ospf router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 17.80.1.1 0.0.0.0 area 0 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! --More-- RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b ospof  f router ospf 1 router-id 4.4.4.4 log-adjacency-changes network 17.80.1.2 0.0.0.0 area 0 ! no ip http server no ip http secure-server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! --More-- RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#sh run | b ospf router ospf 1 router-id 6.6.6.6 log-adjacency-changes network 17.57.100.2 0.0.0.0 area 0 ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 line vty 0 4 login line vty 5 15 login ! ! end --More--   S6# RACK13AS>1 [Resuming connection 1 to r1 ... ]  ! --More--   R1#do sh       shg ip       ip ii nt brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Serial0/0.2 180.40.7.66 YES manual up up Ethernet0/1 17.57.100.1 YES manual up up Serial0/1 unassigned YES unset administratively down down R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#in t  t ki  lo 0 R1(config-if)#ip add 223.1.1.1 255.255.255.09  R1(config-if)#router rip R1(config-router)#net 223.1.1.0 R1(config-router)#int tu 0 R1(config-if)#tun *Mar 1 16:52:15.049: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#tun sou lo 0 R1(config-if)#tun dest 222.1.1.3 R1(config-if)#kee R1(config-if)#keepalive R1(config-if)#ip add 13.13.13.1 255.25.255    5.255.0 R1(config-if)#router o ps[f    ospf 1 R1(config-router)#net 13.13.13.1 2 0.0.0.0 area 0 R1(config-router)# R1(config-router)# R1(config-router)#^Z R1# RACK13AS>3 [Resuming connection 3 to r3 ... ]  ! --More--   R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int lo 0 R3(config-if)#ip add 222.1.1.3 255.255.255.0 R3(config-if)#router eip   rip R3(config-router)#net 222.1.1.1 0 R3(config-router)#int tu 0 R3(config-if)#tun sou lo *Mar 1 16:52:29.472: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R3(config-if)#tun sou lo 0 R3(config-if)#tun dest 223.1.1.1 R3(config-if)#ke R3(config-if)#keepalive R3(config-if)# *Mar 1 16:52:37.693: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3(config-if)#ip add 12 3.13.13.3 255.255.255.0 R3(config-if)#router ospf 1 R3(config-router)#net 13./ 13.13.3 0.. 0.0.0 area 0 R3(config-router)#^Z R3# *Mar 1 16:52:55.867: %SYS-5-CONFIG_I: Configured from console by console R3#p 13.13.13.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 13.13.13.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/72/72 ms R3# R3# R3# R3# R3# *Mar 1 16:53:02.418: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3# R3# R3# R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 1.1.1.1 0 FULL/ - 00:00:37 13.13.13.1 Tunnel0 4.4.4.4 1 FULL/DR 00:00:39 17.80.1.2 FastEthernet0/0 R3# RACK13AS>4 [Resuming connection 4 to r4 ... ]  end --More--   R4#sh ip rout Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11122] via 17.80.1.1, 00:00:09, FastEthernet0/0 13.0.0.0/24 is subnetted, 1 subnets O 13.13.13.0 [110/11112] via 17.80.1.1, 00:00:09, FastEthernet0/0 R4#~p    p 17.57.100.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/72/72 ms R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh run | b Lo interface Loopback0 ip address 223.1.1.1 255.255.255.0 ! interface Tunnel0 ip address 13.13.13.1 255.255.255.0 keepalive 10 3 tunnel source Loopback0 tunnel destination 222.1.1.3 ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 --More--   frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 half-duplex ! interface Serial0/1 no ip address shutdown ! router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router ospf 1 router-id 1.1.1.1 log-adjacency-changes network 13.13.13.1 0.0.0.0 area 0 network 17.57.100.1 0.0.0.0 area 0 ! --More--  router rip version 2 redistribute eigrp 100 metric 4 passive-interface Ethernet0/0 offset-list 1 out 3 network 208.28.1.0 network 223.1.1.0 maximum-paths 3 distance 190 0.0.0.0 255.255.255.255 2 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.193 access-list 2 permit 208.28.1.194 ! ! ! ! ! --More-- RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b Lo interface Loopback0 ip address 222.1.1.3 255.255.255.0 ! interface Tunnel0 ip address 13.13.13.3 255.255.255.0 keepalive 10 3 tunnel source Loopback0 tunnel destination 223.1.1.1 ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto --More--  ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown ! --More--  interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 13.13.13.3 0.0.0.0 area 0 network 17.80.1.1 0.0.0.0 area 0 ! router rip --More--   version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! --More--   R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#deb fram pack Frame Relay packet debugging is on R2# *Mar 1 16:59:04.752: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2# *Mar 1 16:59:09.311: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2# *Mar 1 16:59:12.861: Serial1/0.1: broadcast search *Mar 1 16:59:12.861: Serial1/0.1:encaps failed on broadcast for link 7(IP) *Mar 1 16:59:12.873: Serial1/0.1(o): dlci 203(0x30B1), pkt type 0x800(IP), datagramsize 216 *Mar 1 16:59:13.799: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2# *Mar 1 16:59:14.844: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 76 *Mar 1 16:59:15.590: Serial1/0(i): dlci 201(0x3091), pkt type 0x2000, datagramsize 339 R2# *Mar 1 16:59:18.402: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2#u l *Mar 1 16:59:22.677: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2#u ll  all All possible debugging has been turned off R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#cio  onfi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rouer osp      ter ps  ospf 1 R3(config-router)#redi R3(config-router)#redistribute rip su R3(config-router)#redistribute rip subnets R3(config-router)#router rip R3(config-router)#redi R3(config-router)#redistribute osp R3(config-router)#redistribute ospf 1 met 5 R3(config-router)#^Z R3# RACK13AS>1 [Resuming connection 1 to r1 ... ]  ! --More--   R1# *Mar 1 17:59:35.632: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 17:59:36.634: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 17:59:36.634: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#our   rouer  ter rip R1(config-router)#redis R1(config-router)#redistribute osp R1(config-router)#redistribute ospf 1 met 5 R1(config-router)#router eugr   u igrp 100 R1(config-router)#redi R1(config-router)#redistribute ospf 1 met 1.1.    1 1 1 1 R1(config-router)#router ospf 1 R1(config-router)#redi R1(config-router)#redistribute rip % Only classful networks will be redistributed R1(config-router)#redistribute rip su R1(config-router)#redistribute rip subnets R1(config-router)#red R1(config-router)#redistribute   eigrp 100 su R1(config-router)#redistribute eigrp 100 subnets R1(config-router)#^Z R1# *Mar 1 18:00:25.498: %SYS-5-CONFIG_I: Configured from console by console R1# *Mar 1 18:00:46.637: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1# *Mar 1 18:00:49.185: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1# *Mar 1 18:01:33.381: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired R1# *Mar 1 18:02:17.169: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1# *Mar 1 18:02:25.671: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 18:02:26.677: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 18:02:26.681: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1# *Mar 1 18:03:36.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1# *Mar 1 18:03:47.289: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1# *Mar 1 18:03:55.707: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 18:03:56.724: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 18:03:56.724: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R1# *Mar 1 18:05:06.743: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1#sh i *Mar 1 18:05:13.178: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1#sh ip route ospf R1#sh ip route ospf R1#sh ip route ospf R1#sh ip route ospf R1#sh ip route ospf R1#sh ip route ospf R1#sh ip route ospf R1#sh ip route ospf 17.0.0.0/24 is subnetted, 2 subnets O 17.80.1.0 [110/11112] via 13.13.13.3, 00:00:00, Tunnel0 O E2 222.1.1.0/24 [110/20] via 13.13.13.3, 00:00:00, Tunnel0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.193/32 [110/20] via 13.13.13.3, 00:00:00, Tunnel0 O E2 208.28.1.194/32 [110/20] via 13.13.13.3, 00:00:00, Tunnel0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks O E2 180.40.7.0/27 [110/20] via 13.13.13.3, 00:00:00, Tunnel0 R1# *Mar 1 18:05:25.742: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 18:05:26.744: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 18:05:26.744: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R1# *Mar 1 18:06:36.771: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1# *Mar 1 18:06:43.241: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1# *Mar 1 18:06:55.762: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 18:06:56.763: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 18:06:56.763: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do sh ip access Standard IP access list 1 10 permit 208.28.1.193 (410 matches) Standard IP access list 2 10 permit 208.28.1.193 (8 matches) 20 permit 208.28.1.194 (8 matches) R1(config)#access-list *Mar 1 18:08:06.814: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config)#access-list *Mar 1 18:08:17.339: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1(config)#access-list *Mar 1 18:08:25.813: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 18:08:26.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 18:08:26.815: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R1(config)#access-list *Mar 1 18:09:36.838: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config)#access-list *Mar 1 18:09:43.236: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1(config)#access-list *Mar 1 18:09:55.849: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 18:09:56.843: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 18:09:56.851: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config)#access-list *Mar 1 18:11:06.853: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config)#access-list *Mar 1 18:11:13.256: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1(config)#access-list *Mar 1 18:11:25.881: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 18:11:26.858: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 18:11:26.902: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config)#access-list *Mar 1 18:12:36.905: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config)#access-list *Mar 1 18:12:47.446: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1(config)#access-list *Mar 1 18:12:55.916: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 18:12:56.954: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 18:12:56.958: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config)#access-list do sh ip access Standard IP access list 1 10 permit 208.28.1.193 (450 matches) Standard IP access list 2 10 permit 208.28.1.193 (11 matches) 20 permit 208.28.1.194 (11 matches) R1(config)#do sh ip accessredistribute eigrp 100 subnets do sh ip access  access-list 3 r den 222.1.1.90  = 0 R1(config)#access-list 3 den 222.1.1.0\\\\                 per 0.0.0.       a  any R1(config)#rouer ospf 1 ^ % Invalid input detected at '^' marker. R1(config)#rouer ospf 1ter ospf 1 R1(config-router)#distr R1(config-router)#distribute-list 3 in tu 0 R1(config-router)# *Mar 1 18:14:06.921: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-router)# *Mar 1 18:14:13.247: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1(config-router)#^Z R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] *M R3# R3#con *Mar 1 18:13:08.689: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 18:13:09.690: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 18:13:09.690: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#do sh access-l R3(config)#cpo   accce  ess-list 1 per 223.1.1.0 R3(config)#rouer ospf         ter osof 1 ^ % Invalid input detected at '^' marker. R3(config)#router osof 1 1  1 p 1f 1 R3(config-router)#distan R3(config-router)#distance 255 1.1.1.1 0. *Mar 1 18:14:19.693: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3(config-router)#distance 255 1.1.1.1 0.0.0..\  0 *Mar 1 18:14:24.501: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3(config-router)#distance 255 1.1.1.1 0.0.0.0 1 R3(config-router)#^Z R3#sh ip *Mar 1 18:14:42.182: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip rout ospf 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/11121] via 13.13.13.1, 00:00:12, Tunnel0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.128/27 [110/20] via 13.13.13.1, 00:00:12, Tunnel0 O E2 208.28.1.64/28 [110/20] via 13.13.13.1, 00:00:12, Tunnel0 O E2 208.28.1.0/24 [110/20] via 13.13.13.1, 00:00:12, Tunnel0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks O E2 180.40.0.0/16 [110/20] via 13.13.13.1, 00:00:12, Tunnel0 O E2 180.40.7.64/27 [110/20] via 13.13.13.1, 00:00:12, Tunnel0 R3# R3# R3# R3#sh ip rout ospf 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/11121] via 13.13.13.1, 00:00:16, Tunnel0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.128/27 [110/20] via 13.13.13.1, 00:00:16, Tunnel0 O E2 208.28.1.64/28 [110/20] via 13.13.13.1, 00:00:16, Tunnel0 O E2 208.28.1.0/24 [110/20] via 13.13.13.1, 00:00:16, Tunnel0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks O E2 180.40.0.0/16 [110/20] via 13.13.13.1, 00:00:16, Tunnel0 O E2 180.40.7.64/27 [110/20] via 13.13.13.1, 00:00:16, Tunnel0 R3#sh ip rout rip R 223.1.1.0/24 [120/1] via 208.28.1.1, 00:00:23, Serial1/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.3, 00:00:25, Serial1/0 R 208.28.1.194/32 [120/4] via 208.28.1.3, 00:00:25, Serial1/0 R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 redistribute ospf 1 metric 1 1 1 1 1 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router ospf 1 router-id 1.1.1.1 log-adjacency-changes redistribute eigrp 100 subnets redistribute rip subnets network 13.13.13.1 0.0.0.0 area 0 network 17.57.100.1 0.0.0.0 area 0 distribute-list 3 in Tunnel0 ! router rip version 2 redistribute eigrp 100 metric 4 redistribute ospf 1 metric 5 passive-interface Ethernet0/0 offset-list 1 out 3 --More--   network 208.28.1.0 network 223.1.1.0 maximum-paths 3 distance 190 0.0.0.0 255.255.255.255 2 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.193 access-list 2 permit 208.28.1.194 access-list 3 deny 222.1.1.0 access-list 3 permit any ! ! ! ! ! ! line con 0 exec-timeout 0 0 --More--   R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3# R3#sh run | b router router ospf 1 router-id 3.3.3.3 log-adjacency-changes redistribute rip subnets network 13.13.13.3 0.0.0.0 area 0 network 17.80.1.1 0.0.0.0 area 0 distance 255 1.1.1.1 0.0.0.0 1 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 redistribute ospf 1 metric 5 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! --More--  no ip http server no ip http secure-server ! access-list 1 permit 223.1.1.0 ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! end R3# R3#conif t ^ % Invalid input detected at '^' marker. R3#conifi t ^ % Invalid input detected at '^' marker. R3#con   confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#time R3(config)#time-range Prob14 R3(config-time-range)#p R3(config-time-range)#periodic ? Friday Friday Monday Monday Saturday Saturday Sunday Sunday Thursday Thursday Tuesday Tuesday Wednesday Wednesday daily Every day of the week weekdays Monday thru Friday weekend Saturday and Sunday R3(config-time-range)#periodic week R3(config-time-range)#periodic weekd R3(config-time-range)#periodic weekdays ? hh:mm Starting time R3(config-time-range)#periodic weekdays 0:00 to 7:59 R3(config-time-range)#periodic weekdays 0:00 to 7:59              17:01 to 2400  :00 ^ % Invalid input detected at '^' marker. R3(config-time-range)#periodic weekdays 17:01 to 24:00    3:59 R3(config-time-range)#exit R3(config)#access-list 100 per ospf any any tim R3(config)#access-list 100 per ospf any any time-range Pt rob14 R3(config)#route-map Prob14 R3(config-route-map)#match ip add 100 R3(config-route-map)#set in R3(config-route-map)#set interface null 0 R3(config-route-map)#set interface null 0match ip add 100 set interface null 0 ip    exit R3(config)#ip lo R3(config)#ip local po R3(config)#ip local pol R3(config)#ip local policy rou R3(config)#ip local policy route-map Prob14 R3(config)#do sh access-list Standard IP access list 1 10 permit 223.1.1.0 (1 match) Extended IP access list 100 10 permit ospf any any time-range Prob14 (active) R3(config)#do sh ip ospf               do sh access-listip local policy route-map Prob14nip local policy route-map Prob14oip local policy route-map Prob14 ip local policy route-map Prob14 R3(config)#no route R3(config)#no route-map Prob14 R3(config)#no route-map Prob14ip local policy route-map Prob14do sh access-list ip local policy route-map Prob14exit set interface null 0match ip add 100 route-map Prob14access-list 100 per ospf any any time-range Prob14naccess-list 100 per ospf any any time-range Prob14oaccess-list 100 per ospf any any time-range Prob14 access-list 100 per ospf any any time-range Prob14 R3(config)#no access-list 100 per ospf any any time-range Prob14 ospf any any time-range Prob14  ospf any any time-range Prob14  ospf any any time-range Prob14 d ospf any any time-range Prob14e ospf any any time-range Prob14n ospf any any time-range Prob14no access-list 100 den ospf any any time-range Prob14 access-list 100 den ospf any any time-range Prob14 access-list 100 den ospf any any time-range Prob14  R3(config)#access-list 100 den ospf any any time-range Prob14                                  per ip any any R3(config)#int tu 0 R3(config-if)#ip acc R3(config-if)#ip access R3(config-if)#ip access-group 100 in R3(config-if)#do sh clock *18:30:32.680 UTC Mon Mar 1 1993 R3(config-if)#do sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 1.1.1.1 0 FULL/ - 00:00:05 13.13.13.1 Tunnel0 4.4.4.4 1 FULL/DR 00:00:30 17.80.1.2 FastEthernet0/0 R3(config-if)#do sh ip ospf nei *Mar 1 18:31:04.388: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired R3(config-if)#do sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 4.4.4.4 1 FULL/DR 00:00:33 17.80.1.2 FastEthernet0/0 R3(config-if)#^Z R3#set clo *Mar 1 18:31:13.182: %SYS-5-CONFIG_I: Configured from console by console R3#set clock ? % Unrecognized command R3#set clock           clock set ? hh:mm:ss Current Time R3#clock set 15:36 7:00 ? <1-31> Day of the month MONTH Month of the year R3#clock set 15:37:00 onfi t lock set 15:37:00 :37:00 4:37:00 :37:00 1 march 2007 R3#sh access-list Standard IP access list 1 10 permit 223.1.1.0 (1 match) Extended IP access list 100 10 deny ospf any any time-range Prob14 (inactive) (17 matches) 20 permit ip any any (9 matches) R3# R3# R3# R3# Mar 1 14:37:09.134: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3#sh time time-range entry: Prob14 (inactive) periodic weekdays 0:00 to 7:59 periodic weekdays 17:01 to 23:59 used in: IP ACL entry R3# R3# R3# R3#sh run | b Tu interface Tunnel0 ip address 13.13.13.3 255.255.255.0 ip access-group 100 in keepalive 10 3 tunnel source Loopback0 tunnel destination 223.1.1.1 ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 --More--   ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address --More--   shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 3.3.3.3 log-adjacency-changes redistribute rip subnets network 13.13.13.3 0.0.0.0 area 0 network 17.80.1.1 0.0.0.0 area 0 distance 255 1.1.1.1 0.0.0.0 1 ! router rip --More--   version 2 no validate-update-source timers basic 30 180 0 240 redistribute ospf 1 metric 5 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 1 permit 223.1.1.0 access-list 100 deny ospf any any time-range Prob14 access-list 100 permit ip any any ! ! ! --More--  ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! time-range Prob14 periodic weekdays 0:00 to 7:59 periodic weekdays 17:01 to 23:59 ! ! end R3#