=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.07.17 13:04:12 =~=~=~=~=~=~=~=~=~=~=~= confi gt ^ % Invalid input detected at '^' marker. S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int vl  an 10 S5(config-if)# 05:01:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to down S5(config-if)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 unassigned YES unset down down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down --More--   S5(config-if)#do sh vlanb  VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S5(config-if)#ip add 208.28.1.65 255.255.255.240 S5(config-if)#exit S5(config)#vlan 10 S5(config-vlan)#name ToR1 S5(config-vlan)#do sh run     vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S5(config-vlan)#exit S5(config)#exitdo sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 ToR1 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 --More--   S5(config)#do sh run | i Vlan interface Vlan1 interface Vlan10 S5(config)#do sh run | i Vlanlan vlan vlan internal allocation policy ascending S5(config)# 05:03:01: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up S5(config)#do sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10 S5(config)#exit S5#conf 05:03:38: %SYS-5-CONFIG_I: Configured from console by console S5#conf gt ^ % Invalid input detected at '^' marker. S5#c vlan data % Warning: It is recommended to configure VLAN from config mode, as VLAN database mode is being deprecated. Please consult user documentation for configuring VTP/VLAN in config mode. S5(vlan)#vlan 20 ? are Maximum number of All Route Explorer hops for this VLAN backupcrf Backup CRF mode of the VLAN bridge Bridging characteristics of the VLAN media Media type of the VLAN mtu VLAN Maximum Transmission Unit name Ascii name of the VLAN parent ID number of the Parent VLAN of FDDI or Token Ring type VLANs ring Ring number of FDDI or Token Ring type VLANs said IEEE 802.10 SAID state Operational state of the VLAN ste Maximum number of Spanning Tree Explorer hops for this VLAN stp Spanning tree characteristics of the VLAN tb-vlan1 ID number of the first translational VLAN for this VLAN (or zero if none) tb-vlan2 ID number of the second translational VLAN for this VLAN (or zero if none) S5(vlan)#vlan 20 name R T0 oR2 VLAN 20 added: Name: ToR2 S5(vlan)#sh cur S5(vlan)#sh current VLAN ISL Id: 1 Name: default Media Type: Ethernet VLAN 802.10 Id: 100001 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 10 Name: ToR1 Media Type: Ethernet VLAN 802.10 Id: 100010 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 1002 Name: fddi-default Media Type: FDDI VLAN 802.10 Id: 101002 State: Operational --More--   S5(vlan)#app S5(vlan)#apply APPLY completed. S5(vlan)#apply sh current VLAN ISL Id: 1 Name: default Media Type: Ethernet VLAN 802.10 Id: 100001 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 10 Name: ToR1 Media Type: Ethernet VLAN 802.10 Id: 100010 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 20 Name: ToR2 Media Type: Ethernet VLAN 802.10 Id: 100020 State: Operational --More--   S5(vlan)#exit APPLY completed. Exiting.... S5#sh run \ ^ % Invalid input detected at '^' marker. S5#sh run \  Building configuration... Current configuration : 2289 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname S5 ! ! no aaa new-model ip subnet-zero no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst --More--  spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport mode dynamic desirable ! interface FastEthernet0/2 switchport mode dynamic desirable shutdown ! interface FastEthernet0/3 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport mode dynamic desirable shutdown ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 --More--   switchport mode dynamic desirable ! interface FastEthernet0/7 switchport mode dynamic desirable ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable ! --More--  interface FastEthernet0/14 switchport mode dynamic desirable ! interface FastEthernet0/15 switchport mode dynamic desirable ! interface FastEthernet0/16 switchport mode dynamic desirable ! interface FastEthernet0/17 switchport mode dynamic desirable ! interface FastEthernet0/18 switchport mode dynamic desirable ! interface FastEthernet0/19 switchport mode dynamic desirable ! interface FastEthernet0/20 switchport mode dynamic desirable ! interface FastEthernet0/21 switchport mode dynamic desirable --More--  ! interface FastEthernet0/22 switchport mode dynamic desirable ! interface FastEthernet0/23 switchport mode dynamic desirable ! interface FastEthernet0/24 switchport mode dynamic desirable ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address shutdown ! interface Vlan10 ip address 208.28.1.65 255.255.255.240 ! --More--  ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 no login line vty 5 15 no login ! ! end S5# S5#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 ToR1 active 20 ToR2 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 --More--   S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int vlan 1 20 S5(config-if)#ip add 208 05:05:07: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up S5(config-if)#ip add 208.28.1.130 255.255.255.224 S5(config-if)#int s   fa 0/1 S5(config-if)#sw S5(config-if)#switchport mode access S5(config-if)#sw S5(config-if)#switchport acc vlan 10 S5(config-if)#int rang fa 0/1 - 23 S5(config-if-range)#swi S5(config-if-range)#switchport mo S5(config-if-range)#switchport mode acc S5(config-if-range)#switchport mode access S5(config-if-range)#switchport mode access                        span S5(config-if-range)#spanning-tree po S5(config-if-range)#spanning-tree portf S5(config-if-range)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast will be configured in 23 interfaces due to the range command but will only have effect when the interfaces are in a non-trunking mode. S5(config-if-range)#^Z S5#c 05:07:02: %SYS-5-CONFIG_I: Configured from console by console S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#vlan 34 S5(config-vlan)#name BlueSuede S5(config-vlan)#int fa 0/3 S5(config-if)#sw S5(config-if)#switchport acce S5(config-if)#switchport access vlan 34 S5(config-if)#^Z S5# 05:10:33: %SYS-5-CONFIG_I: Configured from console by console S5# RACK14AS> [Resuming connection 5 to r5 ... ] S5# S5#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/2, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Gi0/1, Gi0/2 10 ToR1 active Fa0/1 20 ToR2 active 34 BlueSuede active Fa0/3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 34 enet 100034 1500 - - - - - 0 0 --More--   S5# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S6#sh vtp stat VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 1005 Number of existing VLANs : 5 VTP Operating Mode : Server VTP Domain Name : VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x57 0xCD 0x40 0x65 0x63 0x59 0x47 0xBD Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00 Local updater ID is 0.0.0.0 (no valid interface found) S6# RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#vtp da S5(config)#vtp daGraceland ^ % Invalid input detected at '^' marker. S5(config)#vtp daGracelandGraceland oGracelandmGraceland Graceland Changing VTP domain name from NULL to Graceland S5(config)#^Z S5# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6#sh vtp stat VTP Version : 2 Configuration Revision : 3 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x86 0x53 0xAB 0x6E 0x46 0xF8 0x84 0xA6 Configuration last modified by 208.28.1.65 at 3-1-93 05:10:14 Local updater ID is 0.0.0.0 (no valid interface found) S6#. \ sh vla VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 ToR1 active 20 ToR2 active 34 BlueSuede active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 --More--   S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa0/4 S6(config-if)#int range fa 0/1 - 24 3 S6(config-if-range)#sw S6(config-if-range)#switchport mode acc S6(config-if-range)#s span S6(config-if-range)#spanning-tree po S6(config-if-range)#spanning-tree portf S6(config-if-range)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast will be configured in 23 interfaces due to the range command but will only have effect when the interfaces are in a non-trunking mode. S6(config-if-range)#int fa 0/4 S6(config-if)#sw S6(config-if)#switchport acc S6(config-if)#switchport access vlan S6(config-if)#switchport access vlan 34 S6(config-if)#switchport access vlan 34int fa 0/4 spanning-tree portfast int fa 0/4  2 S6(config-if)#int fa 0/2switchport access vlan 34  20 S6(config-if)#cv  exit S6(config)#vtp pru S6(config)#vtp pruning ? S6(config)#vtp pruning Pruning switched on S6(config)#^Z S6# RACK14AS>5 [Resuming connection 5 to r5 ... ] 0 S5#sh vtp stat VTP Version : 2 Configuration Revision : 4 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x2D 0x91 0x18 0x58 0x14 0x02 0x34 0xF5 Configuration last modified by 0.0.0.0 at 3-1-93 05:15:24 Local updater ID is 208.28.1.65 on interface Vl10 (lowest numbered VLAN interface found) S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,20,34 S5# RACK14AS>6 [Resuming connection 6 to r6 ... ] 05: S6#confi g ^ % Invalid input detected at '^' marker. S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa0/1 S6(config-if)#ip address 17.57.100.2.  255.255.255.0 ^ % Invalid input detected at '^' marker. S6(config-if)#no swi S6(config-if)#no switchport S6(config-if)#no switchport ip address 17.57.100.2 255.255.255.0no switchport  do sh int status 05:18:21: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 05:18:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up S6(config-if)#do sh int status Port Name Status Vlan Duplex Speed Type Fa0/1 connected routed a-half a-10 10/100BaseTX Fa0/2 connected 20 a-full a-100 10/100BaseTX Fa0/3 disabled 1 auto auto 10/100BaseTX Fa0/4 connected 34 a-full a-100 10/100BaseTX Fa0/5 notconnect 1 auto auto 10/100BaseTX Fa0/6 notconnect 1 auto auto 10/100BaseTX Fa0/7 notconnect 1 auto auto 10/100BaseTX Fa0/8 notconnect 1 auto auto 10/100BaseTX Fa0/9 notconnect 1 auto auto 10/100BaseTX Fa0/10 notconnect 1 auto auto 10/100BaseTX Fa0/11 notconnect 1 auto auto 10/100BaseTX Fa0/12 notconnect 1 auto auto 10/100BaseTX Fa0/13 notconnect 1 auto auto 10/100BaseTX Fa0/14 notconnect 1 auto auto 10/100BaseTX Fa0/15 notconnect 1 auto auto 10/100BaseTX Fa0/16 notconnect 1 auto auto 10/100BaseTX Fa0/17 notconnect 1 auto auto 10/100BaseTX Fa0/18 notconnect 1 auto auto 10/100BaseTX Fa0/19 notconnect 1 auto auto 10/100BaseTX Fa0/20 notconnect 1 auto auto 10/100BaseTX Fa0/21 notconnect 1 auto auto 10/100BaseTX --More--   Port Name Status Vlan Duplex Speed Type Fa0/22 notconnect 1 auto auto 10/100BaseTX Fa0/23 notconnect 1 auto auto 10/100BaseTX Fa0/24 connected trunk a-full a-100 10/100BaseTX Gi0/1 notconnect 1 auto auto unknown Gi0/2 notconnect 1 auto auto unknown S6(config-if)#do sh int statusno switchport ip address 17.57.100.2 255.255.255.0 S6(config-if)# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Ethernet0/1 unassigned YES unset administratively down down Serial0/1 unassigned YES unset administratively down down R1#confi gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ip addres 17.2 57.100.1 255.255.255.0 R1(config-if)#no suht ^ % Invalid input detected at '^' marker. R1(config-if)#no shut R1(config-if)#^Z R1# *Mar 1 05:17:14.338: %SYS-5-CONFIG_I: Configured from console by console R1# RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#pin 208.28.1.66 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/202/1004 ms S5#pin 208.28.1.66  129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/201/1000 ms S5# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6(config-if)#^Z S6#p 17 05:19:34: %SYS-5-CONFIG_I: Configured from console by console S6#p 17.1 57.100.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/202/1000 ms S6# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#po    17.80.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/3/4 ms R3# RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | 0/1 ^ % Invalid input detected at '^' marker. S5#\sh run | 0/1pin 208.28.1.129sh run | 0/1 b0/1 0/1 interface FastEthernet0/1 switchport access vlan 10 switchport mode access spanning-tree portfast ! interface FastEthernet0/2 switchport mode access shutdown spanning-tree portfast ! interface FastEthernet0/3 switchport access vlan 34 switchport mode access spanning-tree portfast ! interface FastEthernet0/4 switchport mode access shutdown spanning-tree portfast ! interface FastEthernet0/5 switchport mode access spanning-tree portfast --More--   S5#sh run | b Vlan interface Vlan1 no ip address shutdown ! interface Vlan10 ip address 208.28.1.65 255.255.255.240 ! interface Vlan20 ip address 208.28.1.130 255.255.255.224 ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 --More--   S5# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6#sh run ] | b 0/1 interface FastEthernet0/1 no switchport ip address 17.57.100.2 255.255.255.0 spanning-tree portfast ! interface FastEthernet0/2 switchport access vlan 20 switchport mode access spanning-tree portfast ! interface FastEthernet0/3 switchport mode access shutdown spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 34 switchport mode access spanning-tree portfast ! interface FastEthernet0/5 switchport mode access spanning-tree portfast --More--   S6#sh vtp stat VTP Version : 2 Configuration Revision : 4 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x2D 0x91 0x18 0x58 0x14 0x02 0x34 0xF5 Configuration last modified by 0.0.0.0 at 3-1-93 05:15:24 Local updater ID is 17.57.100.2 on interface Fa0/1 (first layer3 interface found) S6# S6#sh vln an br S6#sh vlan brief VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/3, Fa0/5, Fa0/6, Fa0/7 Fa0/8, Fa0/9, Fa0/10, Fa0/11 Fa0/12, Fa0/13, Fa0/14, Fa0/15 Fa0/16, Fa0/17, Fa0/18, Fa0/19 Fa0/20, Fa0/21, Fa0/22, Fa0/23 Gi0/1, Gi0/2 10 ToR1 active 20 ToR2 active Fa0/2 34 BlueSuede active Fa0/4 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup S6# S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/24 S6(config-if)#swi S6(config-if)#switchport mode trunk Command rejected: An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode. S6(config-if)#switchport mode trunktrunk trunk trunk trunk trunk trunk ? allowed Set allowed VLAN characteristics when interface is in trunking mode encapsulation Set trunking encapsulation when interface is in trunking mode native Set trunking native characteristics when interface is in trunking mode pruning Set pruning VLAN characteristics when interface is in trunking mode S6(config-if)#switchport trunk en S6(config-if)#switchport trunk encapsulation ? dot1q Interface uses only 802.1q trunking encapsulation when trunking isl Interface uses only ISL trunking encapsulation when trunking negotiate Device will negotiate trunking encapsulation with peer on interface S6(config-if)#switchport trunk encapsulation do S6(config-if)#switchport trunk encapsulation dot1q S6(config-if)#switchport trunk encapsulation dot1q mode trunk  05:23:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down S6(config-if)#switchport mode trunk S6(config-if)# 05:23:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up S6(config-if)#swi S6(config-if)#switchport tr S6(config-if)#switchport trunk a S6(config-if)#switchport trunk allowed ? vlan Set allowed VLANs when interface is in trunking mode S6(config-if)#switchport trunk allowed vlan ? WORD VLAN IDs of the allowed VLANs when this port is in trunking mode add add VLANs to the current list all all VLANs except all VLANs except the following none no VLANs remove remove VLANs from the current list S6(config-if)#switchport trunk allowed vlan 10,20,34 S6(config-if)#^Z S6#sh run 05:25:29: %SYS-5-CONFIG_I: Configured from console by console S6#sh run int fa 0. /24 Building configuration... Current configuration : 135 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport trunk allowed vlan 10,20,34 switchport mode trunk end S6# RACK14AS>5 [Resuming connection 5 to r5 ... ] 05 S5#confi g   t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#interface FastEthernet0/24 S5(config-if)# switchport trunk encapsulation dot1q S5(config-if)# switchport trunk allowed vlan 10,20,34 S5(config-if)# switchport mode trunk S5(config-if)#^Z S5# 05:25:42: %SYS-5-CONFIG_I: Configured from console by console S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)# switchport mode trunktrunk allowed vlan 10,20,34encapsulation dot1q interface FastEthernet0/24  S5(config-if)#interface FastEthernet0/24 switchport mode trunk trunk allowed vlan 10,20,34        50 S5(config-if)# 05:26:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down S5(config-if)#do shr  run int fa 0/24 Building configuration... Current configuration : 129 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport trunk allowed vlan 50 switchport mode trunk end S5(config-if)#do sh run int fa 0/24 switchport trunk allowed vlan 50interface FastEthernet0/24  switchport mode trunk trunk allowed vlan 10,20,34 S5(config-if)#^Z S5# 05:27:05: %SYS-5-CONFIG_I: Configured from console by console S5# 05:27:34: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up S5# RACK14AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#confi gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.3 % Incomplete command. R1(config)#int s 0/0.3 po R1(config)#int s 0/0.3 point-to-point R1(config-subif)#eix  xit R1(config)#exitint s 0/0.3 point-to-point nint s 0/0.3 point-to-point oint s 0/0.3 point-to-point  int s 0/0.3 point-to-point  Not all config may be removed and may reappear after reactivating the sub-interface R1(config)#no int s 0/0.3 point-to-point  exit int s 0/0.3 point-to-point                mu R1(config)#int s 0/0.3 multipoint % Warning: cannot change link type R1(config-subif)#do sh int s 0/0.3 multipoint no int s 0/0.3 point-to-point Not all config may be removed and may reappear after reactivating the sub-interface R1(config)#do sh ip int briu e Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Serial0/0.3 unassigned YES unset deleted down Ethernet0/1 17.57.100.1 YES manual up up Serial0/1 unassigned YES unset administratively down down R1(config)#do sh fram map Serial0/0.1 (up): point-to-point dlci, dlci 103(0x67,0x1870), broadcast status defined, active R1(config)#^Z R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh fram amp   map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#sh fram pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 2 0 0 0 Switched 0 0 0 0 Unused 0 1 0 0 DLCI = 301, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 354 output pkts 26 in bytes 115093 out bytes 884 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 26 out bcast bytes 884 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:27:35, last time pvc status changed 05:27:25 --More--   DLCI = 302, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 27 output pkts 13 in bytes 918 out bytes 442 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 13 out bcast bytes 442 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:27:40, last time pvc status changed 05:27:30 --More--   DLCI = 307, DLCI USAGE = UNUSED, PVC STATUS = INACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:27:41, last time pvc status changed 05:27:41 R3# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#sh fram pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 1 0 0 0 Switched 0 0 0 0 Unused 1 1 0 0 DLCI = 201, DLCI USAGE = UNUSED, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 05:30:29, last time pvc status changed 05:30:20 --More--   R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#no fram in R3(config-if)#no fram ina R3(config-if)#no fram inar R3(config-if)#no fram inar ^ % Invalid input detected at '^' marker. R3(config-if)#no fram inar \  v R3(config-if)#no fram inverse-arp R3(config-if)#fram      fram map          do sh fram map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3(config-if)#fram map ip 208.28.1.1 301 R3(config-if)#fram map ip 208.28.1.1 3011 2 302 3 302 R3(config-if)# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s 1/09.  .1 Building configuration... Current configuration : 111 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay interface-dlci 203 end R2#sh fram map Serial1/0.1 (up): ip 208.28.1.2 dlci 203(0xCB,0x30B0), dynamic, broadcast,, status defined, active R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#it  int s 1`/  /0.1 R2(config-subif)#frma  amp    mp ap ip 208.28.1.3 2 203 R2(config-subif)#no frame-relay interface-dlci 203 %Cannot remove PVC as being referenced by map statement R2(config-subif)#no fram map ip 208.28.1.2 203 R2(config-subif)#no fram map ip 208.28.1.2 203e-relay interface-dlci 203 R2(config-subif)#no frame-relay interface-dlci 203 map ip 208.28.1.2 203 e-relay interface-dlci 203fram map ip 208.28.1.2 203  R2(config-subif)#^Z R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#^Z R3#p *Mar 1 05:36:39.030: %SYS-5-CONFIG_I: Configured from console by console R3#p 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/65/93 ms R3#p 208.28.1.1 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R3# RACK14AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#p 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R1#p 208.28.1.2 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R1#p 208.28.1.3 re R1#ping 208.28.1.3 repeat 10000 Type escape sequence to abort. Sending 10000, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: .. RACK14AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#deb ip icmp ICMP packet debugging is on R2# *Mar 1 05:37:33.728: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:37:35.731: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:37:37.735: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:37:39.734: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:37:41.737: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:37:43.741: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:37:45.744: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:37:47.743: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:37:49.746: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2#u all All possible debugging has been turned off R2# *Mar 1 05:37:51.750: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2#[fram       dd eb fram pack Frame Relay packet debugging is on R2# *Mar 1 05:37:59.771: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:37:59.771: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:38:01.770: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:38:01.770: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:38:03.769: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:38:03.773: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:38:05.773: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:38:05.777: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:38:07.776: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:38:07.776: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:38:09.775: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:38:09.779: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:38:11.782: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:38:11.782: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:38:13.786: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:38:13.786: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2#u all All possible debugging has been turned off R2# *Mar 1 05:38:15.785: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:38:15.785: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2#confi gt ^ % Invalid input detected at '^' marker. R2#confi gt ^ % Invalid input detected at '^' marker. R2#confi gt ^ % Invalid input detected at '^' marker. R2#confi gtt  Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)#int s 1/0.1fram map ip 208.28.1.2 203  203 1 203  R2(config-subif)#^Z R2# *Mar 1 05:38:55.386: %SYS-5-CONFIG_I: Configured from console by console R2# RACK14AS>1 [Resuming connection 1 to r1 ... ] ..!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!! RACK14AS> [Resuming connection 1 to r1 ... ] !!!!!!!!!!!!!!!!!!!!! !!!!. Success rate is 84 percent (240/285), round-trip min/avg/max = 112/118/153 ms R1#ping 208.28.1.3 repeat 10000 Type escape sequence to abort. Sending 10000, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!!!!!!!!!!!!. Success rate is 93 percent (15/16), round-trip min/avg/max = 112/116/124 ms R1# R1# R1# R1# R1# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s 1/0/.  .1 Building configuration... Current configuration : 149 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 end R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh u  un int s 1/0 ^ % Invalid input detected at '^' marker. R3#sh un int s 1/0run int s 1/0 Building configuration... Current configuration : 224 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp end R3# R3#deb ipcmp  icmp cmp ^ % Invalid input detected at '^' marker. R3#deb ipi cmpcmp  icmp ICMP packet debugging is on R3#deb fram pack Frame Relay packet debugging is on R3#ping 208.258  8.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: *Mar 1 05:41:11.525: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:41:13.524: Serial1/0:Encaps failed--no map entry link 7(IP) *Mar 1 05:41:13.861: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 353. *Mar 1 05:41:15.528: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:41:17.531: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:41:19.530: Serial1/0:Encaps failed--no map entry link 7(IP). Success rate is 0 percent (0/5) R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#fram map iop    p 208.28.1.2 203 R3(config-if)#fram map ip 208.28.1.2 203 fram map ip 208.28.1.2 203nfram map ip 208.28.1.2 203ofram map ip 208.28.1.2 203 fram map ip 208.28.1.2 203 R3(config-if)#no fram map ip 208.28.1.2 203   302no fram map ip 208.28.1.2 302  fram map ip 208.28.1.2 302  R3(config-if)#^Z R3# *Mar 1 05:42:01.856: %SYS-5-CONFIG_I: Configured from console by console R3#config t gtping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: ! *Mar 1 05:42:07.729: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:07.777: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 60 *Mar 1 05:42:07.777: ICMP: bogus redirect from 208.28.1.3 - for 208.28.1.2 use gw 208.28.1.2 *Mar 1 05:42:07.781: gateway address is one of our addresses *Mar 1 05:42:07.797: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:07.797: ICMP: echo reply sent, src 208.28.1.2, dst 208.28.1.2 *Mar 1 05:42:07.797: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:07.857: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/120/128 ms R3# *Mar 1 05:42:07.857: ICMP: echo reply rcvd, src 208.28.1.2, dst 208.28.1.2 *Mar 1 05:42:07.857: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:07.914: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:07.918: ICMP: echo reply sent, src 208.28.1.2, dst 208.28.1.2 *Mar 1 05:42:07.918: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:07.974: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:07.974: ICMP: echo reply rcvd, src 208.28.1.2, dst 208.28.1.2 *Mar 1 05:42:07.974: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:08.034: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:08.034: ICMP: echo reply sent, src 208.28.1.2, dst 208.28.1.2 *Mar 1 05:42:08.034: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:08.090: Serial1/0(i): dlci 302(0x48E1), pkt R3# type 0x800, datagramsize 104 *Mar 1 05:42:08.094: ICMP: echo reply rcvd, src 208.28.1.2, dst 208.28.1.2 *Mar 1 05:42:08.094: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:08.150: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:08.150: ICMP: echo reply sent, src 208.28.1.2, dst 208.28.1.2 *Mar 1 05:42:08.154: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:08.210: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:08.210: ICMP: echo reply rcvd, src 208.28.1.2, dst 208.28.1.2 *Mar 1 05:42:08.210: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:08.270: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:08.270: ICMP: echo reply sent, src 208.28.1.2, dst 208.28.1.2 *Mar 1 05:42:08.270: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:42:08.326: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:42:08.330: ICMP: echo reply rcvd, src 208.28.1.2, dst 208.28.1.2 R3# R3# *Mar 1 05:42:13.915: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 353 R3#u all All possible debugging has been turned off R3#u all All possible debugging has been turned off R3# R3#u allping 208.28.1.2config t ping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/114/117 ms R3#sj   h run int s 1/0 Building configuration... Current configuration : 259 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp end R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#user One pass R3(config)#user One password For-The-Money ? LINE R3(config)#user One password For-The-Money   R3(config)#int s 1/2 R3(config-if)#shut R3(config-if)# *Mar 1 05:48:32.143: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 05:48:33.145: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#en R3(config-if)#encapsulation ppp R3(config-if)#ppp authen R3(config-if)#ppp authentication ? chap Challenge Handshake Authentication Protocol (CHAP) eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) pap Password Authentication Protocol (PAP) R3(config-if)#ppp authentication pap R3(config-if)#ppp pap ? refuse Refuse to authenticate using PAP sent-username Set outbound PAP username wait Wait for caller to authenticate first R3(config-if)#ppp pap se R3(config-if)#ppp pap sent-username Two ? password Set outbound PAP password R3(config-if)#ppp pap sent-username Two pass For-The-Show R3(config-if)# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#config Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. R2(config)#user Twopass For-The-Showo pass For-The-Show R2(config)#int s 1/2 R2(config-if)#enca ppp R2(config-if)#ppp athen       authe pap R2(config-if)#ppp pap sen R2(config-if)#ppp pap sent-username One p[as   ass For-The-Money R2(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh    deb ppp authen PPP authentication debugging is on R3(config-if)#no shut R3(config-if)# *Mar 1 05:51:16.821: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:51:16.849: Se1/2 PPP: Using default call direction *Mar 1 05:51:16.853: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:51:16.853: Se1/2 PPP: Session handle[37000000] Session id[1] *Mar 1 05:51:16.853: Se1/2 PPP: Authorization required *Mar 1 05:51:16.865: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:51:16.865: Se1/2 PAP: Using password from interface PAP *Mar 1 05:51:16.865: Se1/2 PAP: O AUTH-REQ id 1 len 21 from "Two" *Mar 1 05:51:16.869: Se1/2 PAP: I AUTH-REQ id 1 len 22 from "One" *Mar 1 05:51:16.869: Se1/2 PAP: Authenticating peer One *Mar 1 05:51:16.877: Se1/2 PPP: Sent PAP LOGIN Request R3(config-if)# *Mar 1 05:51:16.877: Se1/2 PPP: Received LOGIN Response PASS *Mar 1 05:51:16.881: Se1/2 PPP: Sent LCP AUTHOR Request *Mar 1 05:51:16.881: Se1/2 PPP: Sent IPCP AUTHOR Request *Mar 1 05:51:16.885: Se1/2 LCP: Received AAA AUTHOR Response PASS *Mar 1 05:51:16.885: Se1/2 IPCP: Received AAA AUTHOR Response PASS *Mar 1 05:51:16.885: Se1/2 PAP: O AUTH-ACK id 1 len 5 *Mar 1 05:51:16.885: Se1/2 PAP: I AUTH-ACK id 1 len 5 *Mar 1 05:51:16.889: Se1/2 PPP: Sent CDPCP AUTHOR Request *Mar 1 05:51:16.889: Se1/2 CDPCP: Received AAA AUTHOR Response PASS *Mar 1 05:51:16.893: Se1/2 PPP: Sent IPCP AUTHOR Request R3(config-if)# *Mar 1 05:51:17.887: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3(config-if)#no    shut R3(config-if)# *Mar 1 05:52:03.911: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 05:52:04.912: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#shut pp pap ? refuse Refuse to authenticate using PAP sent-username Set outbound PAP username wait Wait for caller to authenticate first R3(config-if)#pp pap     ayu  uthen ? chap Challenge Handshake Authentication Protocol (CHAP) eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) pap Password Authentication Protocol (PAP) R3(config-if)#pp authen pap ? WORD Use an authentication list with this name callback Authenticate remote on callback only callin Authenticate remote on incoming call only callout Authenticate remote on outgoing call only chap Challenge Handshake Authentication Protocol (CHAP) default Use the default authentication list eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) one-time Allow use of username*OTP for one-time passwords optional Allow peer to refuse to authenticate R3(config-if)#pp authen pap ch ? WORD Use an authentication list with this name callback Authenticate remote on callback only callin Authenticate remote on incoming call only callout Authenticate remote on outgoing call only default Use the default authentication list eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) one-time Allow use of username*OTP for one-time passwords optional Allow peer to refuse to authenticate R3(config-if)#pp authen pap ch  ap ? WORD Use an authentication list with this name callback Authenticate remote on callback only callin Authenticate remote on incoming call only callout Authenticate remote on outgoing call only default Use the default authentication list eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) one-time Allow use of username*OTP for one-time passwords optional Allow peer to refuse to authenticate R3(config-if)#pp authen pap chap          o R3(config-if)#pp authen op R3(config-if)#pp authen op? % Unrecognized command R3(config-if)#pp authen op \  ? chap Challenge Handshake Authentication Protocol (CHAP) eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) pap Password Authentication Protocol (PAP) R3(config-if)#pp authen pap ? WORD Use an authentication list with this name callback Authenticate remote on callback only callin Authenticate remote on incoming call only callout Authenticate remote on outgoing call only chap Challenge Handshake Authentication Protocol (CHAP) default Use the default authentication list eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) one-time Allow use of username*OTP for one-time passwords optional Allow peer to refuse to authenticate R3(config-if)#pp authen pap op R3(config-if)#pp authen pap optional ? WORD Use an authentication list with this name default Use the default authentication list one-time Allow use of username*OTP for one-time passwords R3(config-if)#pp authen pap optional R3(config-if)#do sh deb PPP: PPP authentication debugging is on R3(config-if)#do sh deb do deb ppp nepo  po  o deb ppp neo ^ % Invalid input detected at '^' marker. R3(config-if)#do deb ppp neo \  PPP protocol negotiation debugging is on R3(config-if)# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 05:5 R2(config-if)#ppp pap sent-username One pass For-The-Moneyauthe pap nppp authe papoppp authe pap ppp authe pap R2(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 155 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp pap sent-username One password 0 For-The-Money end R2(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#no shut R3(config-if)# *Mar 1 05:55:24.183: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:55:24.207: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:55:24.231: Se1/2 PPP: Outbound cdp packet dropped R3(config-if)# *Mar 1 05:55:26.162: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:55:26.162: Se1/2 PPP: Using default call direction *Mar 1 05:55:26.162: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:55:26.162: Se1/2 PPP: Session handle[48000001] Session id[2] *Mar 1 05:55:26.162: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 05:55:26.162: Se1/2 PPP: Authorization required *Mar 1 05:55:26.162: Se1/2 LCP: O CONFREQ [Closed] id 2 len 14 *Mar 1 05:55:26.162: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:55:26.166: Se1/2 LCP: MagicNumber 0x14C48796 (0x050614C48796) *Mar 1 05:55:26.166: Se1/2 LCP: I CONFREQ [REQsent] id 2 len 10 *Mar 1 05:55:26.166: Se1/2 LCP: MagicNumber 0x14C4930D (0x050614C4930D) *Mar 1 05:55:26.170: Se1/2 LCP: O CONFACK [REQsent] id 2 len 10 *Mar 1 05:55:26.170: Se1/2 LCP: MagicNumber 0x14C4930D (0x050614C4930D) *Mar 1 05:55:26.174: Se1/2 LCP: I CONFACK [ACKsent] id 2 len 14 *Mar 1 05:55:26.174: S R3(config-if)#e1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:55:26.174: Se1/2 LCP: MagicNumber 0x14C48796 (0x050614C48796) *Mar 1 05:55:26.174: Se1/2 LCP: State is Open *Mar 1 05:55:26.174: Se1/2 PPP: Phase is AUTHENTICATING, by this end *Mar 1 05:55:26.178: Se1/2 PAP: I AUTH-REQ id 2 len 22 from "One" *Mar 1 05:55:26.178: Se1/2 PAP: Authenticating peer One *Mar 1 05:55:26.178: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:55:26.178: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:55:26.182: Se1/2 PPP: Sent PAP LOGIN Request *Mar 1 05:55:26.182: Se1/2 PPP: Received LOGIN Response PASS *Mar 1 05:55:26.182: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:55:26.182: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:55:26.182: Se1/2 PPP: Sent LCP AUTHOR Request *Mar 1 05:55:26.186: Se1/2 PPP: Sent IPCP AUTHOR Request *Mar 1 05:55:26.186: Se1/2 LCP: Received AAA AUTHOR Response PASS *Mar 1 05:55:26.186: Se1/2 IPCP: Received AAA AUTHOR Response PASS *Mar 1 05:55:26.186: Se1/2 PAP: O AUTH-ACK id 2 len 5 *Mar 1 05:55:26.190: Se1/2 PPP: Phase is UP *Mar 1 05:55:26.190: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 05:55:26.190: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:55:26.190: Se1/2 PPP: Sent CDPCP AUTHOR Request *Mar 1 05:55:26.190: Se1/2 PPP: Process pending ncp packets *Mar 1 05:55:26.194: Se1/2 CDPCP: Received AAA AUTHOR Response PASS *Mar 1 05:55:26.194: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 05:55:26.194: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 05:55:26.194: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:55:26.198: Se1/2 AAA/AUTHOR/IPCP: Start. Her address 180.40.7.2, we want 0.0.0.0 *Mar 1 05:55:26.198: Se1/2 PPP: Sent IPCP AUTHOR Request *Mar 1 05:55:26.198: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 05:55:26.198: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 05:55:26.202: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 05:55:26.202: Se1/2 CDPCP: State is Open *Mar 1 05:55:26.202: Se1/2 AAA/AUTHOR/IPCP: Reject 180.40.7.2, using 0.0.0.0 *Mar 1 05:55:26.202: Se1/2 AAA/AUTHOR/IPCP: Done. Her address 180.40.7.2, we want 0.0.0.0 *Mar 1 05:55:26.202: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 05:55:26.202: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:55:26.206: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 05:55:26.206: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:55:26.206: Se1/2 IPCP: State is Open *Mar 1 05:55:26.210: Se1/2 IPCP: Install route to 180.40.7.2 *Mar 1 05:55:26.210: Se1/2 IPCP: Add link info for cef entry 180.40.7.2 *Mar 1 05:55:27.188: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3(config-if)# R3(config-if)#do pi 180.4. 0.7.3 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/33 ms R3(config-if)#shut R3(config-if)# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 R2(config-if)#do sh run int s 1/2no ppp authe pap  *Mar 1 05:56:56.258: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down *Mar 1 05:56:57.259: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R2(config-if)#no ppp authe papno ppp authe pap ppp authe pap ppp authe pap ppp authe pap op R2(config-if)#ppp authe pap optional R2(config-if)#\ ^Z R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Mano shut R3(config-if)#^Z R3# *Mar 1 05:57:04.808: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:57:04.832: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:57:04.856: Se1/2 PPP: Outbound cdp packet dropped R3# *Mar 1 05:57:06.346: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 05:57:06.783: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:57:06.783: Se1/2 PPP: Using default call direction *Mar 1 05:57:06.783: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:57:06.783: Se1/2 PPP: Session handle[F6000002] Session id[3] *Mar 1 05:57:06.783: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 05:57:06.783: Se1/2 PPP: Authorization required *Mar 1 05:57:06.783: Se1/2 LCP: O CONFREQ [Closed] id 3 len 14 *Mar 1 05:57:06.783: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:57:06.787: Se1/2 LCP: MagicNumber 0x14C610A4 (0x050614C610A4) *Mar 1 05:57:06.787: Se1/2 LCP: I CONFREQ [REQsent] id 3 len 14 *Mar 1 05:57:06.791: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:57:06.791: Se1/2 LCP: MagicNumber 0x14C61C1B (0x050614C61C1B) *Mar 1 05:57:06.791: Se1/2 LCP: O CONFACK [REQsent] id 3 len 14 *Mar 1 05:57:06.791: Se1/2 R3# LCP: AuthProto PAP (0x0304C023) *Mar 1 05:57:06.791: Se1/2 LCP: MagicNumber 0x14C61C1B (0x050614C61C1B) *Mar 1 05:57:06.795: Se1/2 LCP: I CONFACK [ACKsent] id 3 len 14 *Mar 1 05:57:06.795: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:57:06.795: Se1/2 LCP: MagicNumber 0x14C610A4 (0x050614C610A4) *Mar 1 05:57:06.795: Se1/2 LCP: State is Open *Mar 1 05:57:06.795: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:57:06.795: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:57:06.795: Se1/2 PAP: Using password from interface PAP *Mar 1 05:57:06.795: Se1/2 PAP: O AUTH-REQ id 2 len 21 from "Two" *Mar 1 05:57:06.799: Se1/2 PAP: I AUTH-REQ id 3 len 22 from "One" *Mar 1 05:57:06.803: Se1/2 PAP: Authenticating peer One *Mar 1 05:57:06.803: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:57:06.803: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:57:06.803: Se1/2 PPP: Sent PAP LOGIN Request *Mar 1 05:57:06.803: Se1/2 PPP: Received LOGIN Response PASS *Mar 1 05:57:06.807: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:57:06.807: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:57:06.807: Se1/2 PPP: Sent LCP AUTHOR Request *Mar 1 05:57:06.807: Se1/2 PPP: Sent IPCP AUTHOR Request *Mar 1 05:57:06.811: Se1/2 PAP: I AUTH-ACK id 2 len 5 *Mar 1 05:57:06.811: Se1/2 LCP: Received AAA AUTHOR Response PASS *Mar 1 05:57:06.811: Se1/2 IPCP: Received AAA AUTHOR Response PASS *Mar 1 05:57:06.811: Se1/2 PAP: O AUTH-ACK id 3 len 5 *Mar 1 05:57:06.811: Se1/2 PPP: Phase is UP *Mar 1 05:57:06.815: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 05:57:06.815: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:57:06.815: Se1/2 PPP: Sent CDPCP AUTHOR Request *Mar 1 05:57:06.815: Se1/2 PPP: Process pending ncp packets *Mar 1 05:57:06.815: Se1/2 CDPCP: Received AAA AUTHOR Response PASS *Mar 1 05:57:06.819: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 05:57:06.819: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 05:57:06.819: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:57:06.819: Se1/2 AAA/AUTHOR/IPCP: Start. Her address 180.40.7.2, we want 0.0.0.0 *Mar 1 05:57:06.823: Se1/2 PPP: Sent IPCP AUTHOR Request *Mar 1 05:57:06.823: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 05:57:06.823: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 05:57:06.827: Se1/2 AAA/AUTHOR/IPCP: Reject 180.40.7.2, using 0.0.0.0 *Mar 1 05:57:06.827: Se1/2 AAA/AUTHOR/IPCP: Done. Her address 180.40.7.2, we want 0.0.0.0 *Mar 1 05:57:06.827: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 05:57:06.827: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:57:06.827: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 05:57:06.827: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:57:06.827: Se1/2 IPCP: State is Open *Mar 1 05:57:06.831: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 05:57:06.831: Se1/2 CDPCP: State is Open *Mar 1 05:57:06.831: Se1/2 IPCP: Install route to 180.40.7.2 *Mar 1 05:57:06.835: Se1/2 IPCP: Add link info for cef entry 180.40.7.2 *Mar 1 05:57:07.813: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3# R3# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run | b user username Two password 0 For-The-Show ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 duplex auto speed auto --More--  ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp authentication pap optional ppp pap sent-username One password 0 For-The-Money ! interface Serial1/3 --More--   R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b user username One password 0 For-The-Money ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto --More--  ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show ! interface Serial1/3 no ip address --More--   R3#confi g ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#user R1 pass PinkCald  dillac R3(config)# R3# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#\ ci onfi gt ^ % Invalid input detected at '^' marker. R1#confi gtt  Enter configuration commands, one per line. End with CNTL/Z. R1(config)#user R1 pass PinkCadillacR1 pass PinkCadillac 3 pass PinkCadillac R1(config)# RACK14AS>3 [Resuming connection 3 to r3 ... ] * R3#confi g ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0-  R3(config-if)#encap pp         RACK14AS>1 [Resuming connection 1 to r1 ... ] R1(config)#int s /1  1/  0/0.1 R1(config-subif)#fram in R1(config-subif)#fram int R1(config-subif)#fram interface-dlci 103 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R1(config-subif)#fram interface-dlci 103 ppp ? Virtual-Template Virtual Template interface R1(config-subif)#fram interface-dlci 103 ppp vit r R1(config-subif)#fram interface-dlci 103 ppp virtual-Template ? <1-200> Virtual-Template interface number R1(config-subif)#fram interface-dlci 103 ppp virtual-Template 1 R1(config-fr-dlci)# *Mar 1 06:02:51.949: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R1(config-fr-dlci)#exit R1(config-subif)#exit R1(config)#int vir R1(config)#int virtual-temp R1(config)#int virtual-template 1 R1(config-if)#encap pp R1(config-if)#do sh run int    nt virt 1 % Ambiguous command: "sh run int virt 1" R1(config-if)#do sh run int virt 1u 1a 1l 1- 1t 1e 1m 1p 1 Building configuration... Current configuration : 50 bytes ! interface Virtual-Template1 no ip address end R1(config-if)#ppp authen chap R1(config-if)#ip a    do sh run int s /0  9/.   0/0.1 Building configuration... Current configuration : 118 bytes ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 end R1(config-if)# ip address 208.28.1.1 255.255.255.248 R1(config-if)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Serial0/0.3 unassigned YES unset deleted down Ethernet0/1 17.57.100.1 YES manual up up Serial0/1 unassigned YES unset administratively down down Virtual-Access1 208.28.1.1 YES TFTP up down Virtual-Template1 208.28.1.1 YES manual down down Virtual-Access2 unassigned YES unset down down R1(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh run int s 1/0 Building configuration... Current configuration : 259 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp end R3(config-if)# frame-relay map ip 208.28.1.1 301 ? broadcast Broadcasts should be forwarded to this address cisco Use CISCO Encapsulation compress Enable TCP/IP and RTP/IP header compression ietf Use RFC1490/RFC2427 Encapsulation nocompress Do not compress TCP/IP headers payload-compression Use payload compression rtp RTP header compression parameters tcp TCP header compression parameters R3(config-if)# frame-relay map ip 208.28.1.1 301                       do sh run int s 1/0 frame-relay               frame-relay map ip 208.28.1.1 301n frame-relay map ip 208.28.1.1 301o frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.1 301 R3(config-if)#frm am int R3(config-if)#fram int  i nter R3(config-if)#fram interface-d R3(config-if)#fram interface-dlci 301 ? ppp Use RFC1973 Encapsulation to support PPP over FR switched Define a switched DLCI R3(config-if)#fram interface-dlci 301 ppp vir R3(config-if)#fram interface-dlci 301 ppp virtual-Template 1 R3(config-fr-dlci)# *Mar 1 06:04:53.039: Vt1 PPP: Phase is DOWN, Setup *Mar 1 06:04:53.039: Vi1 PPP: Phase is DOWN, Setup *Mar 1 06:04:53.039: Vi1 PPP: Using default call direction *Mar 1 06:04:53.039: Vi1 PPP: Treating connection as a dedicated line *Mar 1 06:04:53.039: Vi1 PPP: Session handle[50000007] Session id[0] *Mar 1 06:04:53.039: Vi1 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:04:53.043: Vi1 PPP: Authorization required *Mar 1 06:04:53.043: Vi1 LCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 06:04:53.043: Vi1 LCP: MagicNumber 0x14CD2DFA (0x050614CD2DFA) *Mar 1 06:04:53.043: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up *Mar 1 06:04:53.071: Vi1 LCP: I CONFREQ [REQsent] id 41 len 15 *Mar 1 06:04:53.071: Vi1 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:04:53.071: Vi1 LCP: MagicNumber 0x0BDA2B4D (0x05060BDA2B4D) *Mar 1 06:04:53.075: Vi1 LCP: O CONFACK [REQsent] id 41 len 15 *Mar 1 06:04:53.075: Vi1 LCP: AuthProto CHAP (0x0305C22305) *Mar R3(config-fr-d1 06:04:53.075: Vi1 LCP: MagicNumber 0x0BDA2B4D (0x05060BDA2B4D) *Mar 1 06:04:53.075: Vi1 LCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 06:04:53.075: Vi1 LCP: MagicNumber 0x14CD2DFA (0x050614CD2DFA) *Mar 1 06:04:53.075: Vi1 LCP: State is Open *Mar 1 06:04:53.075: Vi1 PPP: No authorization without authentication *Mar 1 06:04:53.079: Vi1 PPP: Phase is AUTHENTICATING, by the peer *Mar 1 06:04:53.116: Vi1 CHAP: I CHALLENGE id 1 len 23 from "R1" *Mar 1 06:04:53.120: Vi1 CHAP: Using hostname from unknown source *Mar 1 06:04:53.120: Vi1 CHAP: Using password from AAA *Mar 1 06:04:53.120: Vi1 CHAP: O RESPONSE id 1 len 23 from "R3" *Mar 1 06:04:53.172: Vi1 CHAP: I SUCCESS id 1 len 4 *Mar 1 06:04:53.172: Vi1 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:04:53.172: Vi1 PPP: Phase is ESTABLISHING, Finish LCP *Mar 1 06:04:53.172: Vi1 PPP: Phase is UP *Mar 1 06:04:53.172: Vi1 PPP: Process pending ncp packets *Mar 1 06:04:53.176: Vi1 IPCP: I CONFREQ [Not negotiated] id 1 len 10 *Mar 1 06:04:53.176: Vi1 IPCP: Address 208.28.1.1 (0x0306D01C0101) *Mar 1 06:04:53.176: Vi1 LCP: O PROTREJ [Open] id 2 len 16 protocol IPCP (0x80210101000A0306D01C0101) *Mar 1 06:04:54.173: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to uplci)#exit R3(config-if)#do u all All possible debugging has been turned off R3(config-if)#exit R3(config)#int vir R3(config)#int virtual-temp R3(config)#int virtual-template 1 R3(config-if)#ppp authen chap R3(config-if)#ip add 208.28.1.2 255.255.255.248 R3(config-if)#^Z R3# *Mar 1 06:05:24.559: %SYS-5-CONFIG_I: Configured from console by console R3#sh pi int      ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 17.80.1.1 YES manual up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 208.28.1.2 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.3 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--  Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down Virtual-Access1 208.28.1.2 YES TFTP up up Virtual-Template1 208.28.1.2 YES manual down down Virtual-Access2 unassigned YES unset down down R3#ping 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/69/89 ms R3# RACK14AS>1 [Resuming connection 1 to r1 ... ] *Mar R1(config-if)#int s0/. 0.1 R1(config-subif)#no ip add R1(config-subif)#^Z R1# *Mar 1 06:07:25.325: %SYS-5-CONFIG_I: Configured from console by console R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#ping 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3#ping 208.28.1.1 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3#sh run itn    nt s 1/0 Building configuration... Current configuration : 278 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 frame-relay interface-dlci 301 ppp Virtual-Template1 no frame-relay inverse-arp end R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.1/32 is directly connected, Virtual-Access1 C 208.28.1.0/29 is directly connected, Serial1/0 is directly connected, Virtual-Access1 180.40.0.0/16 is variably subnetted, 2 subnets, 2 masks C 180.40.7.2/32 is directly connected, Serial1/2 C 180.40.7.0/27 is directly connected, Serial1/2 R3# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#ping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R1#ping 208.28.1.2 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/116/117 ms R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#confi g ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int p add 208.28.1.2 255.255.255.248ppp authen chap int virtual-template 1 R3(config-if)#ip un R3(config-if)#ip unn R3(config-if)#ip unnumbered s 1/0 R3(config-if)#^Z R3# *Mar 1 06:08:41.081: %SYS-5-CONFIG_I: Configured from console by console R3#config t g sh ip routerun int s 1/0ping 208.28.1.3 1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/64/80 ms R3#ping 208.28.1.1config t  g sh ip routerun int s 1/0ping 208.28.1.3  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b 0/0.1 interface Serial0/0.1 point-to-point frame-relay interface-dlci 103 ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 half-duplex ! interface Serial0/1 no ip address shutdown ! interface Virtual-Template1 ip address 208.28.1.1 255.255.255.248 ppp authentication chap ! ip http server ip classless ! ! ! ! ! ! --More--   R1#sh run int     | i user username R3 password 0 PinkCadillac R1# R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | i user username One password 0 For-The-Money username R1 password 0 PinkCadillac ppp pap sent-username Two password 0 For-The-Show R3#sh run | b 1/0 interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 frame-relay interface-dlci 301 ppp Virtual-Template1 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show ! interface Serial1/3 no ip address shutdown --More--  ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! interface Virtual-Template1 ip unnumbered Serial1/0 ppp authentication chap ! ip classless ! --More--   R3# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#shut R1(config-subif)#do deb ppp authen PPP authentication debugging is on R1(config-subif)#no shut R1(config-subif)#^Z R1# *Mar 1 06:13:18.304: %SYS-5-CONFIG_I: Configured from console by console R1#config t config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#no shutdo deb ppp authenshut int s 0/0.1 R1(config-subif)#shut R1(config-subif)#do    do sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 29 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: disabled, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 34 message lines logged R1(config-subif)#do    exit R1(config)#log buff R1(config)#int s 0/0.1 R1(config-subif)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 unassigned YES manual administratively down down Serial0/0.3 unassigned YES unset deleted down Ethernet0/1 17.57.100.1 YES manual up up Serial0/1 unassigned YES unset administratively down down Virtual-Access1 208.28.1.1 YES TFTP up up Virtual-Template1 208.28.1.1 YES manual down down Virtual-Access2 unassigned YES unset down down R1(config-subif)#no suht ^ % Invalid input detected at '^' marker. R1(config-subif)#no shut R1(config-subif)#int s 1/  9./   no shutuhtdo sh ip int brieint s 0/0.1    R1(config-if)#shut R1(config-if)# *Mar 1 06:14:18.074: %LINK-5-CHANGED: Interface Serial0/0, changed state to administratively down R1(config-if)# *Mar 1 06:14:18.078: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down R1(config-if)# *Mar 1 06:14:19.076: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down *Mar 1 06:14:19.080: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to down R1(config-if)#no shut R1(config-if)# *Mar 1 06:14:23.916: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R1(config-if)# *Mar 1 06:14:23.916: Vi1 PPP: Using default call direction *Mar 1 06:14:23.916: Vi1 PPP: Treating connection as a dedicated line *Mar 1 06:14:23.916: Vi1 PPP: Session handle[FF000005] Session id[3] *Mar 1 06:14:23.920: Vi1 PPP: Authorization required R1(config-if)# *Mar 1 06:14:25.915: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up *Mar 1 06:14:25.939: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down *Mar 1 06:14:26.917: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up R1(config-if)# *Mar 1 06:14:35.931: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R1(config-if)# *Mar 1 06:14:35.931: Vi1 PPP: Using default call direction *Mar 1 06:14:35.931: Vi1 PPP: Treating connection as a dedicated line *Mar 1 06:14:35.931: Vi1 PPP: Session handle[6E000006] Session id[4] *Mar 1 06:14:35.935: Vi1 PPP: Authorization required R1(config-if)# *Mar 1 06:14:42.017: Vi1 CHAP: O CHALLENGE id 3 len 23 from "R1" *Mar 1 06:14:42.017: Vi1 CHAP: I CHALLENGE id 2 len 23 from "R3" *Mar 1 06:14:42.021: Vi1 CHAP: Using hostname from unknown source *Mar 1 06:14:42.021: Vi1 CHAP: Using password from AAA *Mar 1 06:14:42.021: Vi1 CHAP: O RESPONSE id 2 len 23 from "R1" *Mar 1 06:14:42.037: Vi1 CHAP: I RESPONSE id 3 len 23 from "R3" *Mar 1 06:14:42.041: Vi1 PPP: Sent CHAP LOGIN Request *Mar 1 06:14:42.045: Vi1 CHAP: I SUCCESS id 2 len 4 *Mar 1 06:14:42.045: Vi1 PPP: Received LOGIN Response PASS *Mar 1 06:14:42.045: Vi1 PPP: Sent LCP AUTHOR Request *Mar 1 06:14:42.049: Vi1 PPP: Sent IPCP AUTHOR Request R1(config-if)# *Mar 1 06:14:42.049: Vi1 LCP: Received AAA AUTHOR Response PASS *Mar 1 06:14:42.053: Vi1 IPCP: Received AAA AUTHOR Response PASS *Mar 1 06:14:42.053: Vi1 CHAP: O SUCCESS id 3 len 4 *Mar 1 06:14:42.065: Vi1 PPP: Sent IPCP AUTHOR Request *Mar 1 06:14:43.087: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up R1(config-if)#^Z R1# *Mar 1 06:15:41.799: %SYS-5-CONFIG_I: Configured from console by console R1#wr Building configuration... [OK] R1#sh start Using 933 out of 29688 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! boot-start-marker boot-end-marker ! logging buffered 4096 debugging ! memory-size iomem 10 no aaa new-model ip subnet-zero ! ! no ip domain lookup ! ip cef ! --More--  ! ! ! ! ! ! ! ! ! ! username R3 password 0 PinkCadillac ! ! ! ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay no fair-queue --More--  ! interface Serial0/0.1 point-to-point frame-relay interface-dlci 103 ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 half-duplex ! interface Serial0/1 no ip address shutdown ! interface Virtual-Template1 ip address 208.28.1.1 255.255.255.248 ppp authentication chap ! ip http server ip classless ! ! ! ! ! --More--   R1# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s1/2 R2(config-if)#shut R2(config-if)#e *Mar 1 06:15:44.315: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 06:15:45.317: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R2(config-if)#encap ? alc Airline Line Control (ALC) atm-dxi ATM-DXI encapsulation bstun Block Serial tunneling (BSTUN) frame-relay Frame Relay networks hdlc Serial HDLC synchronous lapb LAPB (X.25 Level 2) ppp Point-to-Point protocol sdlc SDLC sdlc-primary SDLC (primary) sdlc-secondary SDLC (secondary) smds Switched Megabit Data Service (SMDS) stun Serial tunneling (STUN) uts Unisys TS x25 X.25 R2(config-if)#encap lap R2(config-if)#encap lapb ? appletalk AppleTalk clns ISO CLNS dce DCE operation decnet DECnet dte DTE operation ip IP ipv6 IPV6 ipx Novell IPX multi Multiprotocol operation pppoe PPP over Ethernet qllc qllc protocol snapshot Snapshot routing support R2(config-if)#encap lapb            ppp ? accm Set initial Async Control Character Map accounting Set PPP network accounting method acfc Options for HDLC Address & Control Field Compression authentication Set PPP link authentication method authorization Set PPP network authorization method bridge Enable PPP bridge translation caller Caller option when no CLID is available chap Set CHAP authentication parameters direction Override default PPP direction dnis Authentication via DNIS before LCP eap Set EAP authentication parameters encrypt Enable PPP encryption ipcp Set IPCP negotiation options iphc Set IPCP Header Compression control options lcp PPP LCP configuration link Set miscellaneous link parameters loopback PPP loopback options max-bad-auth Allow multiple authentication failures max-configure Number of conf-reqs sent before assuming peer is unable to respond max-failure Number of conf-naks sent before assuming configuration is not converging --More--   max-terminate Number of term-reqs sent before assuming peer is unable to respond ms-chap Set MS-CHAP authentication parameters ms-chap-v2 Set MS-CHAP-V2 authentication parameters multilink Make interface multilink capable pap Set PAP authentication parameters pfc Options for Protocol Field Compression quality Set parameters related to Link Quality Monitoring (LQM) reliable-link Use LAPB with PPP to provide a reliable link timeout Set PPP timeout parameters R2(config-if)#ppp reliable-link R2(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#itn s    nt s 1/2 R3(config-if)#encap la R3(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 86 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation lapb end R3(config-if)#do sh run int s 1/2 encap la   pp R3(config-if)#encap ppdo sh run int s 1/2 Building configuration... Current configuration : 169 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show end R3(config-if)#ppp reh  R3(config-if)#ppp reh ^ % Invalid input detected at '^' marker. R3(config-if)#ppp reh    R3(config-if)#ppp reliable-link R3(config-if)#^Z R3# R3# *Mar 1 06:17:23.417: %SYS-5-CONFIG_I: Configured from console by console R3#sh deb R3# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#do deb ppp ne PPP protocol negotiation debugging is on R2(config-if)#no h shut R2(config-if)# *Mar 1 06:17:40.874: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:17:40.898: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:17:40.922: Se1/2 PPP: Outbound cdp packet dropped R2(config-if)# *Mar 1 06:17:42.845: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 06:17:42.845: Se1/2 PPP: Using default call direction *Mar 1 06:17:42.845: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:17:42.845: Se1/2 PPP: Session handle[A8000003] Session id[4] *Mar 1 06:17:42.845: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:17:42.845: Se1/2 LCP: O CONFREQ [Closed] id 4 len 18 *Mar 1 06:17:42.845: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:17:42.849: Se1/2 LCP: MagicNumber 0x14D8ED06 (0x050614D8ED06) *Mar 1 06:17:42.849: Se1/2 LCP: ReliableLink window 7 addr 0 (0x0B040700) *Mar 1 06:17:42.857: Se1/2 LCP: I CONFREQ [REQsent] id 1 len 18 *Mar 1 06:17:42.857: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:17:42.857: Se1/2 LCP: MagicNumber 0x14D8E19F (0x050614D8E19F) *Mar 1 06:17:42.857: Se1/2 LCP: ReliableLink window 7 addr 0 (0x0B040700) *Mar 1 06:17:42.857: Se1/2 LCP: O CONFNAK [REQsent] id 1 len 8 *M R2(config-if)#ar 1 06:17:42.861: Se1/2 LCP: ReliableLink window 7 addr 1 (0x0B040701) *Mar 1 06:17:42.861: Se1/2 LCP: I CONFNAK [REQsent] id 4 len 8 *Mar 1 06:17:42.861: Se1/2 LCP: ReliableLink window 7 addr 3 (0x0B040703) *Mar 1 06:17:42.861: Se1/2 LCP: O CONFREQ [REQsent] id 5 len 18 *Mar 1 06:17:42.861: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:17:42.861: Se1/2 LCP: MagicNumber 0x14D8ED06 (0x050614D8ED06) *Mar 1 06:17:42.861: Se1/2 LCP: ReliableLink window 7 addr 3 (0x0B040703) *Mar 1 06:17:42.869: Se1/2 LCP: I CONFREQ [REQsent] id 2 len 18 *Mar 1 06:17:42.869: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:17:42.869: Se1/2 LCP: MagicNumber 0x14D8E19F (0x050614D8E19F) *Mar 1 06:17:42.869: Se1/2 LCP: ReliableLink window 7 addr 1 (0x0B040701) *Mar 1 06:17:42.869: Se1/2 LCP: O CONFACK [REQsent] id 2 len 18 *Mar 1 06:17:42.869: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:17:42.869: Se1/2 LCP: MagicNumber 0x14D8E19F (0x050614D8E19F) *Mar 1 06:17:42.869: Se1/2 LCP: ReliableLink window 7 addr 1 (0x0B040701) *Mar 1 06:17:42.873: Se1/2 LCP: I CONFACK [ACKsent] id 5 len 18 *Mar 1 06:17:42.873: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:17:42.873: Se1/2 LCP: MagicNumber 0x14D8ED06 (0x050614D8ED06) *Mar 1 06:17:42.873: Se1/2 LCP: ReliableLink window 7 addr 3 (0x0B040703) *Mar 1 06:17:42.873: Se1/2 LCP: State is Open *Mar 1 06:17:42.877: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:17:42.877: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:17:42.877: Se1/2 PAP: Using password from interface PAP *Mar 1 06:17:42.877: Se1/2 PAP: O AUTH-REQ id 4 len 22 from "One" *Mar 1 06:17:42.885: Se1/2 PAP: I AUTH-REQ id 1 len 21 from "Two" *Mar 1 06:17:42.885: Se1/2 PAP: Authenticating peer Two *Mar 1 06:17:42.885: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:17:42.885: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:17:42.889: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:17:42.889: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 06:17:42.893: Se1/2 PAP: O AUTH-ACK id 1 len 5 R2(config-if)# R2(config-if)# *Mar 1 06:17:47.321: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2(config-if)# *Mar 1 06:17:52.862: Se1/2 AUTH: Timeout 1 *Mar 1 06:17:52.862: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:17:52.862: Se1/2 PAP: Using password from interface PAP *Mar 1 06:17:52.862: Se1/2 PAP: O AUTH-REQ id 5 len 22 from "One" *Mar 1 06:17:52.874: Se1/2 PAP: I AUTH-ACK id 5 len 5 *Mar 1 06:17:52.874: Se1/2 PPP: Phase is UP *Mar 1 06:17:52.878: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 06:17:52.878: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:17:52.878: Se1/2 PPP: Process pending ncp packets *Mar 1 06:17:52.878: Se1/2 CDPCP: I CONFREQ [Closed] id 1 len 4 *Mar 1 06:17:52.878: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 06:17:52.882: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:17:52.882: Se1/2 AAA/AUTHOR/IPCP: Start. Her address 180.40.7.3, we want 0.0.0.0 *Mar 1 06:17:52.882: Se1/2 AAA/AUTHOR/IPCP: Reject 180.40.7.3, using 0.0.0.0 *Mar 1 06:17:52.882: Se1/2 AAA/AUTHOR/IPCP: Done. Her address R2(config-if)#180.40.7.3, we want 0.0.0.0 *Mar 1 06:17:52.886: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 06:17:52.886: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:17:52.886: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 06:17:52.886: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:17:52.886: Se1/2 IPCP: State is Open *Mar 1 06:17:52.890: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 06:17:52.890: Se1/2 IPCP: Install route to 180.40.7.3 *Mar 1 06:17:52.894: Se1/2 IPCP: Add link info for cef entry 180.40.7.3 *Mar 1 06:17:52.894: Se1/2 CDPCP: I CONFACK [REQsent] id 1 len 4 R2(config-if)# *Mar 1 06:17:54.861: Se1/2 CDPCP: I CONFREQ [ACKrcvd] id 2 len 4 *Mar 1 06:17:54.861: Se1/2 CDPCP: O CONFACK [ACKrcvd] id 2 len 4 *Mar 1 06:17:54.861: Se1/2 CDPCP: State is Open R2(config-if)#^Z R2#sh run i   *Mar 1 06:18:43.609: %SYS-5-CONFIG_I: Configured from console by console R2#sh run   int s 1/2 Serial1/2 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is 180.40.7.2/27 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, LCP Open Open: CDPCP, IPCP LAPB DTE, state CONNECT, modulo 8, k 7, N1 12048, N2 3 T1 3000, T2 0, interface outage (partial T3) 0, T4 0, PPP over LAPB VS 3, VR 4, tx NR 4, Remote VR 3, Retransmissions 0 Queues: U/S frames 0, I frames 0, unack. 0, reTx 0 IFRAMEs 19/20 RNRs 0/0 REJs 0/0 SABM/Es 1/1 FRMRs 0/0 DISCs 0/0, loopback not set Keepalive set (10 sec) Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 00:27:59 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/2/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec --More--   R2#confi gt ^ % Invalid input detected at '^' marker. R2#coo nfig t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#itn s 1/2 ^ % Invalid input detected at '^' marker. R2(config)#ppp re R2(config)#ppp rel R2(config)#ppp rel       itn s 1/2 s 1/2  s 1/2 n s 1/2t s 1/2 R2(config-if)#pp re R2(config-if)#pp reliable-link ? R2(config-if)#pp reliable-link               ? accm Set initial Async Control Character Map accounting Set PPP network accounting method acfc Options for HDLC Address & Control Field Compression authentication Set PPP link authentication method authorization Set PPP network authorization method bridge Enable PPP bridge translation caller Caller option when no CLID is available chap Set CHAP authentication parameters direction Override default PPP direction dnis Authentication via DNIS before LCP eap Set EAP authentication parameters encrypt Enable PPP encryption ipcp Set IPCP negotiation options iphc Set IPCP Header Compression control options lcp PPP LCP configuration link Set miscellaneous link parameters loopback PPP loopback options max-bad-auth Allow multiple authentication failures max-configure Number of conf-reqs sent before assuming peer is unable to respond max-failure Number of conf-naks sent before assuming configuration is not converging --More--   max-terminate Number of term-reqs sent before assuming peer is unable to respond ms-chap Set MS-CHAP authentication parameters ms-chap-v2 Set MS-CHAP-V2 authentication parameters multilink Make interface multilink capable pap Set PAP authentication parameters pfc Options for Protocol Field Compression quality Set parameters related to Link Quality Monitoring (LQM) reliable-link Use LAPB with PPP to provide a reliable link timeout Set PPP timeout parameters R2(config-if)#pp    la R2(config-if)#laP p ? N1 Maximum number of bits per I-frame N2 Maximum number of attempts to transmit a frame T1 Retransmission timer T2 Explicit acknowledge deferral timer T4 Keepalive timer interface-outage Interface outage deadband (partial T3) k Maximum number of outstanding frames (window size) modulo Set frame numbering modulus R2(config-if)#lap     ^Z R2#sh run int *Mar 1 06:21:25.635: %SYS-5-CONFIG_I: Configured from console by console R2#sh run int s 1/2 Building configuration... Current configuration : 207 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp reliable-link ppp authentication pap optional ppp pap sent-username One password 0 For-The-Money end R2# R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 R3#sh run int s 1/2 Building configuration... Current configuration : 188 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp reliable-link ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show end R3# R3# RACK14AS>c 4 [Resuming connection 4 to r4 ... ] R4#sh run int atm 1/0 Building configuration... Current configuration : 72 bytes ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive end R4#confi gt ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int atm 10 /0 R4(config-if)#ip addres 192.10.32.14 255.255.255.0 R4(config-if)#pvc ? <0-255> Enter VPI/VCI value(slash required) <1-1023> Enter VCI value WORD Optional handle to refer to this connection R4(config-if)#pvc 0/72 ? ilmi Configure the management PVC for this interface qsaal Configure the signalling PVC for this interface R4(config-if)#pvc 0/72 R4(config-if-atm-vc)#pro R4(config-if-atm-vc)#protocol ? A.B.C.D Protocol specific address arp IP ARP bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol compressedtcp Compressed TCP dlsw Data Link Switching (Direct encapsulation only) ip IP ipv6 IPV6 llc2 llc2 pad PAD links ppp LLC PPP over AAL5 Encapsulation pppoe PPP over Ethernet qllc qllc protocol rsrb Remote Source-Route Bridging snapshot Snapshot routing support stun Serial Tunnel R4(config-if-atm-vc)#protocol ip 192.10.32.254 ? broadcast Pseudo-broadcast no Prevent Pseudo-broadcast on this connection R4(config-if-atm-vc)#protocol ip 192.10.32.254 R4(config-if-atm-vc)#exit R4(config-if)#no shut R4(config-if)#^Z R4#p[in *Mar 1 06:25:58.258: %SYS-5-CONFIG_I: Configured from console by console R4#p[in in in  *Mar 1 06:26:00.014: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up *Mar 1 06:26:01.014: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up R4#pin 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R4#confi gt ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#nat ? % Unrecognized command R4(config)#nat     ip nat ? Stateful Stateful NAT configuration commands inside Inside address translation log NAT Logging outside Outside address translation pool Define pool of addresses service Special translation for application using non-standard port translation NAT translation entry configuration R4(config)#ip nat in ? destination Destination address translation source Source address translation R4(config)#ip nat in sou : > ? list Specify access list describing local addresses route-map Specify route-map static Specify static local->global mapping R4(config)#ip nat in sou list 1 ? interface Specify interface for global address pool Name pool of global addresses R4(config)#ip nat in sou list 1 in atm,    1/09  ? overload Overload an address translation vrf Specify vrf R4(config)#ip nat in sou list 1 in atm 1/0 ov R4(config)#ip nat in sou list 1 in atm 1/0 overload R4(config)#access-list 1 per any R4(config)#int s   fa 0/0 R4(config-if)#ip nat in R4(config-if)#int atm 1/0 R4(config-if)#ip nat out R4(config-if)#^Z R4# *Mar 1 06:27:48.526: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip nat tra R4#pin 192.10.32.254 sou fa 0/0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: Packet sent with a source address of 17.80.1.2 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms R4#pin 192.10.32.254 sou fa 0/0 sh ip nat tra  Pro Inside global Inside local Outside local Outside global icmp 192.10.32.14:1 17.80.1.2:1 192.10.32.254:1 192.10.32.254:1 tcp 192.10.32.14:1 192.10.32.14:179 192.10.32.254:35369 192.10.32.254:35369 R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#cpo  onfi g ^ % Invalid input detected at '^' marker. R3#confi g 1 ^ % Invalid input detected at '^' marker. R3#confi 1 a y sdfnjzbmn ^ % Invalid input detected at '^' marker. R3#~ config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip route 0.0.0.0 0.0.0.0 17.5 80.1.2 R3(config)#^Z R3#pin *Mar 1 06:26:25.073: %SYS-5-CONFIG_I: Configured from console by console R3#pin 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip nat tra Pro Inside global Inside local Outside local Outside global icmp 192.10.32.14:1 17.80.1.2:1 192.10.32.254:1 192.10.32.254:1 icmp 192.10.32.14:12 17.80.1.1:12 192.10.32.254:12 192.10.32.254:12 tcp 192.10.32.14:1 192.10.32.14:179 192.10.32.254:35369 192.10.32.254:35369 R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#pin 192.10.32.254pin 192.10.32.254  192.10.32.254  192.10.32.254  Trying 192.10.32.254 ... Open CR1> CR1> CR1> CR1>sh ? % Unrecognized command CR1>sh    ? Exec commands: <1-99> Session number to resume clear Reset functions disable Turn off privileged commands disconnect Disconnect an existing network connection enable Turn on privileged commands exit Exit from the EXEC lock Lock the terminal login Log in as a particular user logout Exit from the EXEC name-connection Name an existing network connection ping Send echo messages resume Resume an active network connection set Set system parameter (not config) systat Display information about terminal lines terminal Set terminal line parameters traceroute Trace route to destination where List active connections access-enable Create a temporary Access-List entry access-profile Apply user-profile to interface connect Open a terminal connection --More--   CR1>q [Connection to 192.10.32.254 closed by foreign host] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip route 0.0.0.0 0.0.0.0 17.80.1.2ppp reliable-link ip route 0.0.0.0 0.0.0.0 17.80.1.2mip route 0.0.0.0 0.0.0.0 17.80.1.2ip route 0.0.0.0 0.0.0.0 17.80.1.2 nip route 0.0.0.0 0.0.0.0 17.80.1.2oip route 0.0.0.0 0.0.0.0 17.80.1.2 ip route 0.0.0.0 0.0.0.0 17.80.1.2 R3(config)#^Z R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#confi gt ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip nat ? Stateful Stateful NAT configuration commands inside Inside address translation log NAT Logging outside Outside address translation pool Define pool of addresses service Special translation for application using non-standard port translation NAT translation entry configuration R4(config)#ip nat out ? source Source address translation R4(config)#ip nat out sou >? % Unrecognized command R4(config)#ip nat out sou >   ? list Specify access list describing global addresses route-map Specify route-map static Specify static global->local mapping R4(config)#ip nat out sou sta ? A.B.C.D Outside global IP address network Subnet translation tcp Transmission Control Protocol udp User Datagram Protocol R4(config)#ip nat out sou sta 192.10.32.254 ? A.B.C.D Outside local IP address R4(config)#ip nat out sou sta 192.10.32.254 17.80.1.3 R4(config)#ip nat out sou sta 192.10.32.254 17.80.1.3 ? add-route Add a static route for outside local address extendable Extend this translation when used no-alias Do not create an alias for the local address no-payload No translation of embedded address/port in the payload redundancy NAT redundancy operation vrf Specify vrf R4(config)#ip nat out sou sta 192.10.32.254 17.80.1.3 R4(config)#^Z R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] *config t 192.10.32.254pin 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: .. Success rate is 0 percent (0/2) R3#x pi 17.80.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.3, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms R3# R3# R3# R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#confi gt ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip nat out sou sta 192.10.32.254 17.80.1.3   254 % 192.10.32.254 already mapped (17.80.1.3 -> 192.10.32.254) R4(config)#\ ip nat out sou sta 192.10.32.254 17.80.1.2543 e R4(config)#ip nat out sou sta 192.10.32.254 17.80.1.3 extendable R4(config)#ip nat out sou sta 192.10.32.254 17.80.1.3 extendable 254  ex R4(config)#ip nat out sou sta 192.10.32.254 17.80.1.254 extendable R4(config)#ip nat out sou sta 192.10.32.254 17.80.1.254 extendable  extendable 2 extendable  R4(config)#ip nat out sou sta 192.10.32.254 17.80.1.252 extendable  extendable 0 extendable  R4(config)#^Z R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#pi 17.80.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R3#pi 17.80.1.3 254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.254, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms R3#pi 17.80.1.254 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.252, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms R3#pi 17.80.1.252 0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.250, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms R3#pi 17.80.1.250pi 17.80.1.250  17.80.1.250  Trying 17.80.1.250 ... % Connection refused by remote host R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh ip nat tra Pro Inside global Inside local Outside local Outside global --- --- --- 17.80.1.250 192.10.32.254 --- --- --- 17.80.1.252 192.10.32.254 --- --- --- 17.80.1.254 192.10.32.254 --- --- --- 17.80.1.3 192.10.32.254 tcp 192.10.32.14:4 192.10.32.14:179 192.10.32.254:35369 192.10.32.254:35369 R4#deb ip nat IP NAT debugging is on R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip route 0.0.0.0 0.0.0.0 17.80.1.2ip route 0.0.0.0 0.0.0.0 17.80.1.2  R3(config)#^Z R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] *Ma3:20.606: NAT: expiring 192.10.32.14 (192.10.32.14) tcp 4 (179) R4# R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 06:30:53.513: %SYS-5-CONFIG_I: C R3#ping 192.10.2 32.254 rep 10000 Type escape sequence to abort. Sending 10000, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! RACK14AS>4 [Resuming connection 4 to r4 ... ] *Mar17.80.1.1->192.10.32.14, d=192.10.32.254 [97] *Mar 1 06:33:35.414: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [97] *Mar 1 06:33:35.418: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [98 R4#] *Mar 1 06:33:35.418: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [98] *Mar 1 06:33:35.422: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [99] *Mar 1 06:33:35.422: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [99] *Mar 1 06:33:35.426: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [100] *Mar 1 06:33:35.426: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [100] *Mar 1 06:33:35.430: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [101] *Mar 1 06:33:35.434: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [101] *Mar 1 06:33:35.434: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [102] *Mar 1 06:33:35.438: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [102] *Mar 1 06:33:35.438: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [103] *Mar 1 06:33:35.442: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [103] *Mar 1 06:33:35.446: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [104] *Mar 1 06:33:35.446: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [104] *Mar 1 06:33:35.450: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [105] *Mar 1 06:33:35.450: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [105] *Mar 1 06:33:35.454: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [106] *Mar 1 06:33:35.454: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [106] *Mar 1 06:33:35.458: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [107] *Mar 1 06:33:35.458: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [107] *Mar 1 06:33:35.462: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [108] *Mar 1 06:33:35.466: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [108] *Mar 1 06:33:35.466: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [109] *Mar 1 06:33:35.470: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [109] *Mar 1 06:33:35.470: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [110] *Mar 1 06:33:35.474: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [110] *Mar 1 06:33:35.478: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [111] *Mar 1 06:33:35.478: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [111] *Mar 1 06:33:35.482: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [112] *Mar 1 06:33:35.482: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [112] *Mar 1 06:33:35.486: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [113] *Mar 1 06:33:35.486: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [113] *Mar 1 06:33:35.490: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [114] *Mar 1 06:33:35.490: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [114] *Mar 1 06:33:35.494: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [115] *Mar 1 06:33:35.498: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [115] *Mar 1 06:33:35.498: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [116] *Mar 1 06:33:35.502: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [116] *Mar 1 06:33:35.502: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [117] *Mar 1 06:33:35.506: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [117] *Mar 1 06:33:35.506: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [118] *Mar 1 06:33:35.510: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [118] *Mar 1 06:33:35.510: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [119] *Mar 1 06:33:35.514: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [119] *Mar 1 06:33:35.518: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [120] *Mar 1 06:33:35.518: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [120] *Mar 1 06:33:35.522: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [121] *Mar 1 06:33:35.522: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [121] *Mar 1 06:33:35.526: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [122] *Mar 1 06:33:35.526: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [122] *Mar 1 06:33:35.530: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [123] *Mar 1 06:33:35.534: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [123] *Mar 1 06:33:35.534: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [124] *Mar 1 06:33:35.538: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [124] *Mar 1 06:33:35.538: NAT*: s=17.80.1.1->192.10.32.14, d=192.10.32.254 [125] *Mar 1 06:33:35.542: NAT*: s=192.10.32.254, d=192.10.32.14->17.80.1.1 [125] *Mar 1 06:33:35.542: NAT*: s=17.80.1.1->192.10.32.14 RACK14AS>3 [Resuming connection 3 to r3 ... ] !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!. Success rate is 99 percent (1968/1969), round-trip min/avg/max = 4/4/28 ms R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] 2.10.32.254 [126] *Mar 1 06:33 06:33:35.670: NAT*