=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2005.08.25 07:47:59 =~=~=~=~=~=~=~=~=~=~=~= R3# R3# R3# R3# R3# R3# R3# R3# R3# R3#sh fram map R3#sh run int s 12 /0 Building configuration... Current configuration : 121 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon shutdown end R3# R3# R3# R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#no fram in R3(config-if)#no fram ina R3(config-if)#no fram inar R3(config-if)#no fram inar   n? interface-dlci interface-queue intf-type inverse-arp R3(config-if)#no fram inv R3(config-if)#no fram inverse-arp ? appletalk AppleTalk decnet DECnet interval Set inarp time interval on an interface ip IP ipv6 IPV6 ipx Novell IPX pppoe PPP over Ethernet qllc qllc protocol R3(config-if)#no fram inverse-arp R3(config-if)#fram map ip 28.  08.28.1.1 301 R3(config-if)#fram map ip 208.28.1.1 3011 21321  02 302 3 302 R3(config-if)#no shut R3(config-if)#^Z R3# RACK16AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int     do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 208.28.1.129 YES manual up up Serial1/0 unassigned YES manual up up Serial1/0.1 208.28.1.3 YES manual down down Serial1/0.2 180.40.7.65 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.2 YES manual up up Serial1/3 unassigned YES unset administratively down down --More--   R2(config)#do sh run int s 0/0  1  1/0.1 Building configuration... Current configuration : 111 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay interface-dlci 203 end R2(config)#int s 1/0.1 R2(config-subif)#no frame-relay interface-dlci 203 R2(config-subif)#n fram inv R2(config-subif)#fram map ip 208.28.1.2 203 R2(config-subif)#fram map ip 208.28.1.2 203 3 203 1 203 R2(config-subif)#int s1/0.2 R2(config-subif)#no int s1/0.2fram map ip 208.28.1.1 2032 203n fram inv o frame-relay interface-dlci 203 fram inv  R2(config-subif)#n fram invint s1/0.2fram map ip 208.28.1.1 2032 203n fram inv o frame-relay interface-dlci 203int s 1/0.1 do sh run int s 1/0.1ip int brie no router rip do sh ip int brierun int s 1/0.1int s 1/0.1 no frame-relay interface-dlci 203 fram inv fram map ip 208.28.1.2 2031 203int s1/0.2 n fram inv n fram invint s1/0.2fram map ip 208.28.1.1 2032 203n fram inv o frame-relay interface-dlci 203int s 1/0.1 no frame-relay interface-dlci 203 1 R2(config-subif)#fram map ip 180.40.7.66 201 R2(config-subif)#^Z R2# *Mar 1 18:05:15.874: %SYS-5-CONFIG_I: Configured from console by console R2# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1>sh fram % Incomplete command. R1>sh fram map Serial0/0.2 (up): point-to-point dlci, dlci 102(0x66,0x1860), broadcast status defined, active Serial0/0.1 (up): point-to-point dlci, dlci 103(0x67,0x1870), broadcast status defined, active R1>en R1#sh    ping 208.02  2/8  8.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/133/160 ms R1#ping 208.28.1.1 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/70/84 ms R1#ping 208.28.1.2 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/117/124 ms R1#p 180.40.7.63 5 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#rotuer      uter eifr  gr[p  p 100 R1(config-router)#net 180.4.7.64 255.255.255.224 R1(config-router)#do sh run | b router router eigrp 100 network 180.4.7.64 0.0.0.31 auto-summary ! no ip http server ip classless ! ! ! ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 line aux 0 --More--   R1(config-router)#net 208.28.1.66 0.0.0.0 R1(config-router)# R1(config-router)# R1(config-router)# R1(config-router)# R1(config-router)# R1(config-router)# R1(config-router)# RACK16AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#routre    er i eigrp 100 S5(config-router)#nte 208.28.1.0 ^ % Invalid input detected at '^' marker. S5(config-router)#nte 208.28.1.0  208.28.1.0  208.28.1.0 e 208.28.1.0 t 208.28.1.0  S5(config-router)# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eigrp 100 R2(config-router)#net 208.28.1.129 0.0.0.0 R2(config-router)#net 180 % Incomplete command. R2(config-router)#. *Mar 1 18:10:14.780: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.130 (FastEthernet0/1) is up: new adjacency R2(config-router)#.net 180.40.7.65 0.0.0.0 R2(config-router)#q  RACK16AS>1 [Resuming connection 1 to r1 ... ] *Ma R1(config-router)#net 208.28.1.66 0.0.0.0do sh run | b router net 208.28.1.66 0.0.0.0do sh run | b router net 180.4.7.64 255.255.255.224nnet 180.4.7.64 255.255.255.224onet 180.4.7.64 255.255.255.224 net 180.4.7.64 255.255.255.224 R1(config-router)#no net 180.4.7.64 255.255.255.224et 208.28.1.66 0.0.0.0 do sh run | b router net 180.4.7.64 255.255.255.22480.40.7.64 255.255.255.224 R1(config-router)# RACK16AS>2 [Resuming connection 2 to r2 ... ] *Ma R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 12 00:00:11 1 5000 1 0 0 208.28.1.130 Fa0/1 11 00:01:12 240 1440 0 6 R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)#nei 180.40.7.66 s 1/0.2 R2(config-router)# *Mar 1 18:11:59.636: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is down: Static peer configured R2(config-router)# *Mar 1 18:11:59.636: destroy peer: 180.40.7.66 R2(config-router)# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1(config-router)#nei 208   180.40.7.65 s 0/0.2 R1(config-router)# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#nei 180.40.7.66 s 1/0.2do sh ip eigrp nei  *Mar 1 18:12:19.753: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is up: new adjacency R2(config-router)#do sh ip eigrp neinet 180.40.7.65 0.0.0.0do sh ip eigrp nei  IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 11 00:00:03 1 3000 1 0 S 0 208.28.1.130 Fa0/1 11 00:02:08 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 13 00:00:05 1 4500 1 0 S 0 208.28.1.130 Fa0/1 14 00:02:10 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 12 00:00:06 1 4500 1 0 S 0 208.28.1.130 Fa0/1 12 00:02:11 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 11 00:00:08 1 4500 1 0 S 0 208.28.1.130 Fa0/1 11 00:02:13 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 14 00:00:09 1 5000 1 0 S 0 208.28.1.130 Fa0/1 14 00:02:14 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 12 00:00:11 1 5000 1 0 S 0 208.28.1.130 Fa0/1 12 00:02:16 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 11 00:00:12 1 5000 1 0 S 0 208.28.1.130 Fa0/1 11 00:02:17 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 14 00:00:14 1 5000 1 0 S 0 208.28.1.130 Fa0/1 14 00:02:19 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 12 00:00:16 1 5000 1 0 S 0 208.28.1.130 Fa0/1 12 00:02:20 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 11 00:00:17 1 5000 1 0 S 0 208.28.1.130 Fa0/1 11 00:02:22 240 1440 0 6 R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 12 00:00:20 1 5000 1 0 S 0 208.28.1.130 Fa0/1 13 00:02:25 240 1440 0 6 R2(config-router)#do sh ip eigrp neinei 180.40.7.66 s 1/0.2 EIGRP: Static nbr 180.40.7.66 already in AS 100 Serial1/0.2 R2(config-router)#nei 180.40.7.66 s 1/0.2do sh ip eigrp nei nei 180.40.7.66 s 1/0.2do sh ip eigrp nei  IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 10 00:00:27 1 5000 1 0 S 0 208.28.1.130 Fa0/1 11 00:02:32 240 1440 0 6 R2(config-router)#do sh ip eigrp neinei 180.40.7.66 s 1/0.2do sh ip eigrp nei  do sh run |   int s 1/0.2 Building configuration... Current configuration : 144 bytes ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 no frame-relay inverse-arp end R2(config-router)#do sh run int s 1/0.2ip eigrp nei  IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 11 00:00:59 1 5000 0 5 S 0 208.28.1.130 Fa0/1 11 00:03:04 240 1440 0 6 R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:03:16, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:00:18, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:02:16, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# R2(config-router)# RACK16AS>1 [Resuming connection 1 to r1 ... ] * R1(config-router)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 4 subnets, 3 masks D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:04:56, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/28 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:01:21, Null0 180.40.0.0/16 is variably subnetted, 2 subnets, 2 masks D 180.40.0.0/16 is a summary, 00:03:19, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1(config-router)#do sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.66) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 208.28.1.128/27, 1 successors, FD is 281856, serno 2 via 208.28.1.65 (281856/2816), Ethernet0/0 P 208.28.1.64/28, 1 successors, FD is 281600, serno 1 via Connected, Ethernet0/0 P 180.40.0.0/16, 1 successors, FD is 2169856, serno 6 via Summary (2169856/0), Null0 P 208.28.1.0/24, 1 successors, FD is 281600, serno 5 via Summary (281600/0), Null0 via 180.40.7.65 (2172416/28160), Serial0/0.2 P 180.40.7.64/27, 1 successors, FD is 2169856, serno 4 via Connected, Serial0/0.2 R1(config-router)#^Z R1# *Mar 1 18:18:57.786: %SYS-5-CONFIG_I: Configured from console by consolesh run Building configuration... Current configuration : 1157 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! logging queue-limit 100 ! memory-size iomem 10 ip subnet-zero ! ! no ip domain lookup ! mpls ldp logging neighbor-changes ! ! ! ! --More--  ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point --More--   ip address 208.28.1.1 255.255.255.240 frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 half-duplex ! interface Serial0/1 no ip address shutdown ! router eigrp 100 network 180.40.7.64 0.0.0.31 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! no ip http server ip classless --More--  ! ! ! ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 line aux 0 line vty 0 4 ! ! end R1# RACK16AS>2 [Resuming connection 2 to r2 ... ] ^Z R2# *Mar 1 18:18:11.113: %SYS-5-CONFIG_I: Configured from console by console R2#sh run Building configuration... Current configuration : 1721 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R2 ! logging queue-limit 100 ! ip subnet-zero ! ! no ip domain lookup ! ip audit notify log ip audit po max-events 100 mpls ldp logging neighbor-changes ! ! ! --More--  ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto --More--  ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 no frame-relay inverse-arp ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 --More--   no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clockrate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 --More--   no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router eigrp 100 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! ! ! call rsvp-sync ! --More--  ! mgcp profile default ! ! ! dial-peer cor custom ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! end R2# RACK16AS>5 [Resuming connection 5 to r5 ... ] ^Z S5#sh run 18:21:59: %SYS-5-CONFIG_I: Configured from console by console S5#sh run Building configuration... Current configuration : 1863 bytes ! version 12.1 no service single-slot-reload-enable no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname S5 ! ! ip subnet-zero ip routing no ip domain-lookup ! ! spanning-tree extend system-id ! ! ! interface FastEthernet0/1 --More--   switchport access vlan 10 no ip address ! interface FastEthernet0/2 switchport access vlan 16 no ip address ! interface FastEthernet0/3 switchport access vlan 30 no ip address ! interface FastEthernet0/4 no ip address ! interface FastEthernet0/5 no ip address ! interface FastEthernet0/6 no ip address ! interface FastEthernet0/7 no ip address ! --More--  interface FastEthernet0/8 no ip address ! interface FastEthernet0/9 no ip address ! interface FastEthernet0/10 no ip address ! interface FastEthernet0/11 no ip address ! interface FastEthernet0/12 no ip address ! interface FastEthernet0/13 no ip address ! interface FastEthernet0/14 no ip address ! interface FastEthernet0/15 no ip address --More--  ! interface FastEthernet0/16 no ip address ! interface FastEthernet0/17 no ip address ! interface FastEthernet0/18 no ip address ! interface FastEthernet0/19 no ip address ! interface FastEthernet0/20 no ip address ! interface FastEthernet0/21 no ip address ! interface FastEthernet0/22 no ip address ! interface FastEthernet0/23 --More--   no ip address ! interface FastEthernet0/24 no ip address ! interface GigabitEthernet0/1 no ip address ! interface GigabitEthernet0/2 no ip address ! interface Vlan1 no ip address shutdown ! interface Vlan10 ip address 208.28.1.65 255.255.255.240 ! interface Vlan20 ip address 208.28.1.130 255.255.255.224 ! router eigrp 100 network 208.28.1.0 --More--   auto-summary no eigrp log-neighbor-changes ! ip classless ip http server ! ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 login line vty 5 15 login ! end S5# S5# RACK16AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router rip R3(config-router)#ver 2 R3(config-router)#no auto R3(config-router)#net 180.7 40.0.0 R3(config-router)#net 208.28.1.0 R3(config-router)# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#no aut      ver 2 R2(config-router)#no auto R2(config-router)#net     = pass R2(config-router)#passive-interface vlan    fa 0/1 R2(config-router)#pass R2(config-router)#passive-interface s1/0.2 R2(config-router)#net 208.28.1.0 R2(config-router)#net 180.40.0.0 R2(config-router)#nei 208.28.1.2 R2(config-router)# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#net   i 208.28.1.1 R3(config-router)#nei 208.28.1.1 2 R3(config-router)#nei 208.28.1.2 3 R3(config-router)#nei 208.28.1.32nnei 208.28.1.2onei 208.28.1.2 nei 208.28.1.2 R3(config-router)# RACK16AS>c 2 [Resuming connection 2 to r2 ... ] R2(config-router)#nei 208.28.1.2 1 R2(config-router)# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router i rip R1(config-router)#ver 2 R1(config-router)#no sutp    auto R1(config-router)#pass s 0/0.2 R1(config-router)#pass e 0? / R1(config-router)#pass e 0/0 R1(config-router)#net 208.28.1.0 R1(config-router)#net 208.28.1.0pass e 0/0 s 0/0.2npass s 0/0.2opass s 0/0.2 pass s 0/0.2 R1(config-router)#nei 208.28.1.3 R1(config-router)#^Z R1# *Mar 1 18:23:58.543: %SYS-5-CONFIG_I: Configured from console by console RACK16AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#^Z R3#sh ip *Mar 1 18:23:09.190: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:22, Serial1/2 [120/1] via 208.28.1.3, 00:00:22, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:16, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.0 is directly connected, Serial1/2 R 180.40.7.64 [120/1] via 180.40.7.2, 00:00:23, Serial1/2 [120/1] via 208.28.1.3, 00:00:23, Serial1/0 R3#   RACK16AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#^Z R2#sh ip route *Mar 1 18:23:42.577: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:13:28, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:10:31, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:12:28, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router rip R3(config-router)#net 17.0.0.0 R3(config-router)# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets R 17.80.1.0 [120/1] via 180.40.7.3, 00:00:04, Serial1/2 [120/1] via 208.28.1.2, 00:00:04, Serial1/0.1 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:13:50, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:10:52, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:12:51, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1#config tsh run config t sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets R 17.80.1.0 [120/1] via 208.28.1.2, 00:00:14, Serial0/0.1 C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 4 subnets, 3 masks D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:14:42, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/28 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:11:07, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:15, Serial0/0.1 [120/1] via 208.28.1.3, 00:00:09, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:13:06, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#net 17.0.0.0nnet 17.0.0.0onet 17.0.0.0 net 17.0.0.0 R3(config-router)#^Z R3# *Mar 1 18:24:47.739: %SYS-5-CONFIG_I: Configured from console by console R3# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b router rip router rip version 2 passive-interface Ethernet0/0 network 208.28.1.0 neighbor 208.28.1.3 no auto-summary ! no ip http server ip classless ! ! ! ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! --More--   R1# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2#sh ru n| b router rip ^ % Invalid input detected at '^' marker. R2#sh ru n| b router ripru n| b router rip | b router rip n| b router rip | b router rip router rip version 2 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.1 neighbor 208.28.1.2 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! ! ! call rsvp-sync ! ! mgcp profile default ! --More--   R2# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b router router rip version 2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! ! ! call rsvp-sync ! ! mgcp profile default ! ! ! --More--   R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#key chain Prob4 R3(config-keychain)#key 1 R3(config-keychain-key)#key R3(config-keychain-key)#key-string yoyo R3(config-keychain-key)#int s 1/2 R3(config-if)#shut R3(config-if)# *Mar 1 18:27:58.216: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 18:27:59.217: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#ip rip ? authentication Authentication control receive advertisement reception send advertisement transmission triggered enable rfc2091 triggered rip v2-broadcast send ip broadcast v2 update R3(config-if)#ip rip authentication ? key-chain Authentication key-chain mode Authentication mode R3(config-if)#ip rip authentication key R3(config-if)#ip rip authentication key-chain ? LINE name of key-chain R3(config-if)#ip rip authentication key-chain Prob4 R3(config-if)#ip rip authen m R3(config-if)#ip rip authen mode m R3(config-if)#ip rip authen mode md5 ? R3(config-if)#ip rip authen mode md5 R3(config-if)# RACK16AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 18 R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#in  key chain prob4 R2(config-keychain)#key `1 ^ % Invalid input detected at '^' marker. R2(config-keychain)#key `1  1 R2(config-keychain-key)#ke R2(config-keychain-key)#key-string yoyo R2(config-keychain-key)#int s 1/2 R2(config-if)#ip rip authen ke R2(config-if)#ip rip authen key-chain Prob4 R2(config-if)#ip rip wuthen      ait  uthen key-chain Prob4nip rip authen key-chain Prob4oip rip authen key-chain Prob4 ip rip authen key-chain Prob4 R2(config-if)#no ip rip authen key-chain Prob4ip rip authen key-chain Prob4 rob4 prob4 R2(config-if)#ip rip authe mo m R2(config-if)#^Z R2# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do deb ip rip ev RIP event debugging is on R3(config-if)#no *Mar 1 18:29:50.031: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 18:29:50.031: RIP: Update contains 2 routes R3(config-if)#no shut R3(config-if)#^Z R3# *Mar 1 18:29:52.547: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 18:29:53.605: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up R3# *Mar 1 18:29:53.605: rip_route_adjust for Serial1/2 coming up *Mar 1 18:29:53.605: RIP: sending request on Serial1/2 to 224.0.0.9 *Mar 1 18:29:53.665: RIP: received v2 request from 180.40.7.2 on Serial1/2 *Mar 1 18:29:53.665: RIP: sending update with long TTL *Mar 1 18:29:53.665: RIP: sending v2 update to 180.40.7.2 via Serial1/2 (180.40.7.3) *Mar 1 18:29:53.665: RIP: Update contains 4 routes *Mar 1 18:29:53.665: RIP: Update queued *Mar 1 18:29:53.669: RIP: Update sent via Serial1/2 *Mar 1 18:29:53.681: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 18:29:53.681: RIP: Update contains 3 routes *Mar 1 18:29:54.606: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3# *Mar 1 18:29:55.604: RIP: sending v2 flash update to 224.0.0.9 via Serial1/0 (208.28.1.2) *Mar 1 18:29:55.604: RIP: Update contains 1 routes *Mar 1 18:29:55.604: RIP: Update queued *Mar 1 18:29:55.604: RIP: sending v2 flash update to 224.0.0.9 via Serial1/2 (180.40.7.3) - suppressing null update *Mar 1 18:29:55.604: RIP: sending v2 flash update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 18:29:55.604: RIP: Update contains 1 routes *Mar 1 18:29:55.604: RIP: Update queued *Mar 1 18:29:55.604: RIP: sending v2 flash update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 18:29:55.608: RIP: Update contains 1 routes *Mar 1 18:29:55.608: RIP: Update queued R3# *Mar 1 18:29:55.608: RIP: Update sent via Serial1/0 *Mar 1 18:29:55.608: RIP: Update sent via Serial1/0 *Mar 1 18:29:55.608: RIP: Update sent via Serial1/0 *Mar 1 18:29:55.636: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 18:29:55.636: RIP: Update contains 1 routes R3# *Mar 1 18:29:58.621: RIP: received v2 update from 208.28.1.1 on Serial1/0 *Mar 1 18:29:58.621: RIP: Update contains 1 routes R3# *Mar 1 18:30:04.639: RIP: sending v2 update to 224.0.0.9 via Serial1/0 (208.28.1.2) *Mar 1 18:30:04.639: RIP: Update contains 1 routes *Mar 1 18:30:04.639: RIP: Update queued *Mar 1 18:30:04.639: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.3) *Mar 1 18:30:04.639: RIP: Update contains 2 routes *Mar 1 18:30:04.639: RIP: Update queued *Mar 1 18:30:04.639: RIP: sending v2 update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 18:30:04.643: RIP: Update contains 1 routes *Mar 1 18:30:04.643: RIP: Update queued *Mar 1 18:30:04.643: RIP: sending v2 update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 18:30:04.643: RIP: Update contains 1 routes R3# *Mar 1 18:30:04.643: RIP: Update queued *Mar 1 18:30:04.643: RIP: Update sent via Serial1/0 *Mar 1 18:30:04.643: RIP: Update sent via Serial1/2 *Mar 1 18:30:04.643: RIP: Update sent via Serial1/0 *Mar 1 18:30:04.647: RIP: Update sent via Serial1/0 R3#u all All possible debugging has been turned off R3#deb ip rip RIP protocol debugging is on R3# R3# R3# R3# *Mar 1 18:30:18.802: RIP: received packet with MD5 authentication *Mar 1 18:30:18.802: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 18:30:18.802: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 18:30:18.802: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 18:30:18.802: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 18:30:18.822: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 18:30:18.822: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 18:30:18.822: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 18:30:18.822: 208.28.1.128/27 via 0.0.0.0 in 1 hops R3#u all All possible debugging has been turned off R3# RACK16AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh run int s 1/2         | b keuy  y key chain prob4 key 1 key-string yoyo ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! interface FastEthernet0/0 no ip address shutdown --More--   duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 no frame-relay inverse-arp ! interface Serial1/0.2 multipoint --More--   ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip rip authentication mode md5 ip rip authentication key-chain prob4 clockrate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 --More--   R2# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b key key chain Prob4 key 1 key-string yoyo ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto --More--   speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown --More--  ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 --More--   R3# RACK16AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int lo 0 S5(config-if)#ip add 208.28.1.193 2553255    .285  55.255.254 % Warning: use /31 mask on non point-to-point interface cautiously S5(config-if)#ip add 208.28.1.193 255.255.255.254 do sh run int lo 0 Building configuration... Current configuration : 68 bytes ! interface Loopback0 ip address 208.28.1.193 255.255.255.254 end S5(config-if)# S5(config-if)# S5(config-if)# S5(config-if)# S5(config-if)# S5(config-if)#^Z S5# 18:36:36: %SYS-5-CONFIG_I: Configured from console by console S5# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks D 208.28.1.192/31 [90/156160] via 208.28.1.130, 00:00:33, FastEthernet0/1 C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:23:14, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:20:16, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:22:15, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#  config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#redis R2(config-router)#redistribute eigrp 1 ? metric Metric for redistributed routes route-map Route map reference R2(config-router)#redistribute eigrp 1 met R2(config-router)#redistribute eigrp 1 metric 7 2 R2(config-router)# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router rei  ip R1(config-router)#redistribute eigrp 1 metric 20 metric 20 metric 2 R1(config-router)# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#redistribute eigrp 1 metric 20 metric 20 metric 2 R2(config-router)#redistribute eigrp 100 metric 2 metric 2 nredistribute eigrp 1 metric 2oredistribute eigrp 1 metric 2 redistribute eigrp 1 metric 2 R2(config-router)# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks R 208.28.1.192/31 [120/2] via 208.28.1.1, 00:00:13, Serial1/0 [120/2] via 180.40.7.2, 00:00:05, Serial1/2 [120/2] via 208.28.1.3, 00:00:05, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:19, Serial1/0 [120/1] via 180.40.7.2, 00:00:19, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:22, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:14, Serial1/0 [120/2] via 180.40.7.2, 00:00:06, Serial1/2 [120/2] via 208.28.1.3, 00:00:06, Serial1/0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:15, Serial1/0 [120/2] via 180.40.7.2, 00:00:06, Serial1/2 [120/2] via 208.28.1.3, 00:00:06, Serial1/0 R 180.40.7.64/27 [120/1] via 208.28.1.3, 00:00:20, Serial1/0 [120/1] via 180.40.7.2, 00:00:20, Serial1/2 R3# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1(config-router)#exit R1(config)#access-list 1 per 208.28.1.193 2 R1(config)#router rip R1(config-router)#of R1(config-router)#offset-list 1 ? <0-99> Access list of networks to apply offset (0 selects all networks) <1300-1999> Access list of networks to apply offset (expanded range) WORD Access-list name R1(config-router)#offset-list 1 ? in Perform offset on incoming updates out Perform offset on outgoing updates R1(config-router)#offset-list 1 out ? <0-16> Offset R1(config-router)#offset-list 1 out 5 R1(config-router)#^Z R1# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks R 208.28.1.192/31 [120/2] via 180.40.7.2, 00:00:07, Serial1/2 [120/2] via 208.28.1.3, 00:00:07, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:07, Serial1/0 [120/1] via 180.40.7.2, 00:00:07, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:10, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:11, Serial1/0 [120/2] via 180.40.7.2, 00:00:08, Serial1/2 [120/2] via 208.28.1.3, 00:00:08, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks --More--   R3#deb ip rip RIP protocol debugging is on R3# *Mar 1 18:36:27.086: RIP: received v2 update from 208.28.1.1 on Serial1/0 *Mar 1 18:36:27.086: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 18:36:27.086: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 18:36:27.086: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 18:36:27.086: 208.28.1.64/28 via 0.0.0.0 in 1 hops *Mar 1 18:36:27.090: 208.28.1.128/27 via 0.0.0.0 in 2 hops *Mar 1 18:36:27.090: 208.28.1.192/31 via 0.0.0.0 in 7 hops *Mar 1 18:36:28.356: RIP: received packet with MD5 authentication *Mar 1 18:36:28.356: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 18:36:28.356: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 18:36:28.356: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 18:36:28.360: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 18:36:28.360: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 18:36:28.360: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 18:36:28.360: 208.28.1.128/27 via 0.0.0.0 in 1 hops R3# *Mar 1 18:36:28.360: 208.28.1.192/31 via 0.0.0.0 in 2 hops *Mar 1 18:36:28.400: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 18:36:28.400: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 18:36:28.400: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 18:36:28.400: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 18:36:28.400: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 18:36:28.400: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 18:36:28.404: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 18:36:28.404: 208.28.1.192/31 via 0.0.0.0 in 2 hops R3#u all All possible debugging has been turned off R3# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#exit R2(config)#access  -list 1 per 208.28.1.92192 R2(config)#route-map Prob5 per 10 R2(config-route-map)#match ip add 1 R2(config-route-map)#set me R2(config-route-map)#set metric 7 R2(config-route-map)#set metric 7match ip add 1route-map Prob5 per 100 20 R2(config-route-map)#set metric 2 R2(config-route-map)#router rip R2(config-router)#router ripset metric 2route-map Prob5 per 20set metric 7 match ip add 1route-map Prob5 per 10access-list 1 per 208.28.1.192exit no redistribute eigrp 1 metric 2redistribute eigrp 100 metric 2         route R2(config-router)#redistribute eigrp 100 route-map Prob5 ? metric Metric for redistributed routes R2(config-router)#redistribute eigrp 100 route-map Prob5 R2(config-router)#^Z R2# *Mar 1 18:39:37.778: %SYS-5-CONFIG_I: Configured from console by console R2# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks R 208.28.1.192/31 [120/7] via 208.28.1.3, 00:00:01, Serial1/0 [120/7] via 180.40.7.2, 00:00:01, Serial1/2 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:01, Serial1/0 [120/1] via 180.40.7.2, 00:00:01, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:05, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:06, Serial1/0 [120/2] via 180.40.7.2, 00:00:02, Serial1/2 [120/2] via 208.28.1.3, 00:00:02, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks --More--   R3#[A % Unknown command or computer name, or unable to find computer address R3#[Ash ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks R 208.28.1.192/31 [120/7] via 208.28.1.3, 00:00:15, Serial1/0 [120/7] via 180.40.7.2, 00:00:16, Serial1/2 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:15, Serial1/0 [120/1] via 180.40.7.2, 00:00:16, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:19, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:20, Serial1/0 [120/2] via 180.40.7.2, 00:00:17, Serial1/2 [120/2] via 208.28.1.3, 00:00:17, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks --More--   R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks R 208.28.1.192/31 [120/7] via 208.28.1.3, 00:00:22, Serial1/0 [120/7] via 180.40.7.2, 00:00:22, Serial1/2 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:22, Serial1/0 [120/1] via 180.40.7.2, 00:00:22, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:26, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:27, Serial1/0 [120/2] via 180.40.7.2, 00:00:23, Serial1/2 [120/2] via 208.28.1.3, 00:00:23, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks --More--  C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:01, Serial1/0 [120/2] via 180.40.7.2, 00:00:25, Serial1/2 [120/2] via 208.28.1.3, 00:00:25, Serial1/0 R 180.40.7.64/27 [120/1] via 208.28.1.3, 00:00:25, Serial1/0 [120/1] via 180.40.7.2, 00:00:25, Serial1/2 R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks R 208.28.1.192/31 [120/7] via 208.28.1.3, 00:00:11, Serial1/0 [120/7] via 180.40.7.2, 00:00:11, Serial1/2 [120/7] via 208.28.1.1, 00:00:13, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:11, Serial1/0 [120/1] via 180.40.7.2, 00:00:11, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:14, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:14, Serial1/0 [120/2] via 180.40.7.2, 00:00:12, Serial1/2 [120/2] via 208.28.1.3, 00:00:12, Serial1/0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:17, Serial1/0 [120/2] via 180.40.7.2, 00:00:14, Serial1/2 [120/2] via 208.28.1.3, 00:00:14, Serial1/0 R 180.40.7.64/27 [120/1] via 208.28.1.3, 00:00:14, Serial1/0 [120/1] via 180.40.7.2, 00:00:14, Serial1/2 R3# RACK16AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#sh run | b router rip router rip version 2 redistribute eigrp 100 metric 2 passive-interface Ethernet0/0 offset-list 1 out 5 network 208.28.1.0 neighbor 208.28.1.3 no auto-summary ! no ip http server ip classless ! ! ! access-list 1 permit 208.28.1.192 ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom --More--   R1# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b router rip router rip version 2 redistribute eigrp 100 metric 2 route-map Prob5 redistribute eigrp 1 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.1 neighbor 208.28.1.2 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! access-list 1 permit 208.28.1.192 ! route-map Prob5 permit 10 match ip address 1 set metric 7 --More--  ! --More--  route-map Prob5 permit 20 --More--   set metric 2 --More--  ! --More--  ! --More--  call rsvp-sync --More--  ! --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#ip rip ? authentication Authentication control receive advertisement reception send advertisement transmission triggered enable rfc2091 triggered rip v2-broadcast send ip broadcast v2 update R2(config-if)#ip rip triggered ? R2(config-if)#ip rip triggered   R2(config-if)# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ui  int s 1/2 R3(config-if)#ip rip triggered R3(config-if)#^Z R3#s *Mar 1 18:42:38.022: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip proto Routing Protocol is "rip" Sending updates every 30 seconds, next due in 21 seconds Invalid after 180 seconds, hold down 0, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: rip Neighbor(s): 208.28.1.3 208.28.1.1 Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial1/0 2 2 Serial1/2 2 2 Yes Prob4 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 180.40.0.0 208.28.1.0 Routing Information Sources: Gateway Distance Last Update 180.40.7.2 120 00:00:04 208.28.1.1 120 00:00:15 208.28.1.3 120 00:00:10 --More--   R3# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#^Z R2#sh *Mar 1 18:42:57.718: %SYS-5-CONFIG_I: Configured from console by console R2#sh run int s 1/2 Building configuration... Current configuration : 172 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain prob4 clockrate 64000 end R2# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/2 Building configuration... Current configuration : 155 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 end R3# R3# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#? Router configuration commands: address-family Enter Address Family command mode auto-summary Enable automatic network number summarization default Set a command to its defaults default-information Control distribution of default information default-metric Set metric of redistributed routes distance Define an administrative distance distribute-list Filter networks in routing updates exit Exit from routing protocol configuration mode flash-update-threshold Specify flash update threshold in second help Description of the interactive help system input-queue Specify input queue depth maximum-paths Forward packets over multiple paths neighbor Specify a neighbor router network Enable routing on an IP network no Negate a command or set its defaults offset-list Add or subtract offset from RIP metrics output-delay Interpacket delay for RIP updates passive-interface Suppress routing updates on an interface redistribute Redistribute information from another routing protocol timers Adjust routing timers --More--   traffic-share How to compute traffic share over alternate paths validate-update-source Perform sanity checks against source address of routing updates version Set routing protocol version R2(config-router)#output-delay ? <8-50> Delay in milliseconds R2(config-router)#output-delay 10 ? R2(config-router)#output-delay 10 R2(config-router)#^Z R2#sh run *Mar 1 18:44:08.262: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b router rip router rip version 2 timers basic 30 180 0 240 redistribute eigrp 100 metric 2 route-map Prob5 redistribute eigrp 1 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 output-delay 10 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.1 neighbor 208.28.1.2 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! access-list 1 permit 208.28.1.192 ! route-map Prob5 permit 10 --More--   R2# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router rip R3(config-router)#? Router configuration commands: address-family Enter Address Family command mode auto-summary Enable automatic network number summarization default Set a command to its defaults default-information Control distribution of default information default-metric Set metric of redistributed routes distance Define an administrative distance distribute-list Filter networks in routing updates exit Exit from routing protocol configuration mode flash-update-threshold Specify flash update threshold in second help Description of the interactive help system input-queue Specify input queue depth maximum-paths Forward packets over multiple paths neighbor Specify a neighbor router network Enable routing on an IP network no Negate a command or set its defaults offset-list Add or subtract offset from RIP metrics output-delay Interpacket delay for RIP updates passive-interface Suppress routing updates on an interface redistribute Redistribute information from another routing protocol timers Adjust routing timers --More--   traffic-share How to compute traffic share over alternate paths validate-update-source Perform sanity checks against source address of routing updates version Set routing protocol version R3(config-router)# no validate-update-source R3(config-router)#^Z R3# *Mar 1 18:45:08.837: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b router router rip version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! ! ! call rsvp-sync ! ! mgcp profile default ! --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router rip R3(config-router)#maximum-paths ? <1-6> Number of paths R3(config-router)#maximum-paths 3 R3(config-router)#^Z R3#sh run *Mar 1 18:46:58.080: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b router router rip version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! ! ! call rsvp-sync ! ! mgcp profile default --More--   R3# RACK16AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)# R2(config-router)# maximum-paths 3 R2(config-router)#^Z R2# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router rip R1(config-router)# R1(config-router)# maximum-paths 3 R1(config-router)#^Z R1# *Mar 1 18:48:59.996: %SYS-5-CONFIG_I: Configured from console by console R1#copnf     config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router ospf 1 R1(config-router)#router-id 1.1.1.1 R1(config-router)#net 17.0.0.0 0.255.255.255 area 0 R1(config-router)#^Z R1# RACK16AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#router ospf 1 S6(config-router)#router-id 6.6.6.6 S6(config-router)#net 17      net 17.0.0.0 0.255.255.255 area 0 S6(config-router)#^Z S6# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router ospf 1 R3(config-router)#n router-id 3.3.3.3 R3(config-router)#~net 17.0.0.0 0.255.255.255 area 0 ^ % Invalid input detected at '^' marker. R3(config-router)#net 17.0.0.0 0.255.255.255 area 0 R3(config-router)#^Z R3# RACK16AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router ospf 1 R4(config-router)#router-id 4.4.4.4 R4(config-router)# R4(config-router)#net 17.0.0.0 0.255.255.255 area 0 R4(config-router)#^Z R4# *Mar 1 18:52:11.891: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip ospf nei R4#sh ip ospf nei R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:39 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:38 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:37 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:36 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:35 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:34 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:33 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:32 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:32 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:31 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:30 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:30 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:30 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:39 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:39 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:39 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:33 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:38 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 2WAY/DROTHER 00:00:35 17.80.1.1 FastEthernet0/0 R4#deb ip ospf adj OSPF adjacency events debugging is on R4# *Mar 1 18:52:51.007: OSPF: end of Wait on interface FastEthernet0/0 *Mar 1 18:52:51.007: OSPF: DR/BDR election on FastEthernet0/0 *Mar 1 18:52:51.007: OSPF: Elect BDR 4.4.4.4 *Mar 1 18:52:51.007: OSPF: Elect DR 4.4.4.4 *Mar 1 18:52:51.007: OSPF: Elect BDR 3.3.3.3 *Mar 1 18:52:51.007: OSPF: Elect DR 4.4.4.4 *Mar 1 18:52:51.007: DR: 4.4.4.4 (Id) BDR: 3.3.3.3 (Id) *Mar 1 18:52:51.007: OSPF: Send DBD to 3.3.3.3 on FastEthernet0/0 seq 0x14FD opt 0x52 flag 0x7 len 32 *Mar 1 18:52:51.011: OSPF: Rcv DBD from 3.3.3.3 on FastEthernet0/0 seq 0x14FD opt 0x52 flag 0x2 len 52 mtu 1500 state EXSTART *Mar 1 18:52:51.011: OSPF: NBR Negotiation Done. We are the MASTER *Mar 1 18:52:51.015: OSPF: Send DBD to 3.3.3.3 on FastEthernet0/0 seq 0x14FE opt 0x52 flag 0x3 len 52 *Mar 1 18:52:51.015: OSPF: Database request to 3.3.3.3 *Mar 1 18:52:51.015: OSPF: sent LS REQ packet to 17.80.1.1, length 12 *Mar 1 18:52:51.019: OSPF: Rcv DBD from 3.3.3.3 on FastEthernet0/0 seq 0 R4#x14FE opt 0x52 flag 0x0 len 32 mtu 1500 state EXCHANGE *Mar 1 18:52:51.019: OSPF: Send DBD to 3.3.3.3 on FastEthernet0/0 seq 0x14FF opt 0x52 flag 0x1 len 32 *Mar 1 18:52:51.027: OSPF: Rcv DBD from 3.3.3.3 on FastEthernet0/0 seq 0x14FF opt 0x52 flag 0x0 len 32 mtu 1500 state EXCHANGE *Mar 1 18:52:51.027: OSPF: Exchange Done with 3.3.3.3 on FastEthernet0/0 *Mar 1 18:52:51.027: OSPF: Synchronized with 3.3.3.3 on FastEthernet0/0, state FULL *Mar 1 18:52:51.027: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on FastEthernet0/0 from LOADING to FULL, Loading Done R4# *Mar 1 18:52:51.507: OSPF: Build network LSA for FastEthernet0/0, router ID 4.4.4.4 *Mar 1 18:52:51.507: OSPF: Build network LSA for FastEthernet0/0, router ID 4.4.4.4 *Mar 1 18:52:51.511: OSPF: Build router LSA for area 0, router ID 4.4.4.4, seq 0x80000002 R4#u all All possible debugging has been turned off R4# RACK16AS>6 [Resuming connection 6 to r6 ... ] 18:5 S6#sh ip ospf Routing Process "ospf 1" with ID 6.6.6.6 Supports only single TOS(TOS0) routes Supports opaque LSA SPF schedule delay 5 secs, Hold time between two SPFs 10 secs Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs Number of external LSA 0. Checksum Sum 0x0 Number of opaque AS LSA 0. Checksum Sum 0x0 Number of DCbitless external and opaque AS LSA 0 Number of DoNotAge external and opaque AS LSA 0 Number of areas in this router is 1. 1 normal 0 stub 0 nssa External flood list length 0 Area BACKBONE(0) Number of interfaces in this area is 1 Area has no authentication SPF algorithm executed 3 times Area ranges are Number of LSA 3. Checksum Sum 0x24272 Number of opaque link LSA 0. Checksum Sum 0x0 Number of DCbitless LSA 0 Number of indication LSA 0 Number of DoNotAge LSA 0 Flood list length 0 S6#qsh ip ospf config t sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 1.1.1.1 1 FULL/BDR 00:00:31 17.57.100.1 Vlan16 S6# RACK16AS>1 [Resuming connection 1 to r1 ... ] * R1#sh run | b router ospf router ospf 1 router-id 1.1.1.1 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! router rip version 2 redistribute eigrp 100 metric 2 passive-interface Ethernet0/0 offset-list 1 out 5 network 208.28.1.0 neighbor 208.28.1.3 maximum-paths 3 no auto-summary ! no ip http server ip classless ! ! ! access-list 1 permit 208.28.1.192 ! ! --More--   R1# RACK16AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh run | b router ospf router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! ! --More--   R3# RACK16AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b router ospf router ospf 1 router-id 4.4.4.4 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! no ip http server ip classless ! ! ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 exec-timeout 0 0 --More--   R4# RACK16AS>6 [Resuming connection 6 to r6 ... ] S6#sh run | b router ospf router ospf 1 router-id 6.6.6.6 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! ip classless ip http server ! ! ! line con 0 exec-timeout 0 0 line vty 0 4 login line vty 5 15 login ! end S6# S6# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int lo 0 R1(config-if)#ip add 223.1.1.1 255.255.255.0 R1(config-if)#routre  er rip R1(config-router)#net 223.1.1.0 R1(config-router)#int tu 0 R1(config-if)#tun R1(config-if)#tunnel *Mar 1 18:58:34.734: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to downs R1(config-if)#tunnel sou R1(config-if)#tunnel source lo 0 R1(config-if)#tun de R1(config-if)#tun destination 222.1.1.3 R1(config-if)#ip add 17.13.13.13  255.255.3 255.0 R1(config-if)#^Z R1# *Mar 1 18:59:24.776: %SYS-5-CONFIG_I: Configured from console by console RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int lo 0 R3(config-if)#ip add 222.1.1.3 255.255.255.0 R3(config-if)#router rip R3(config-router)#net 222.1.1.0 R3(config-router)#int u tu 0 R3(config-if)#tu *Mar 1 18:58:54.042: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R3(config-if)#tun sou in  lo 0 R3(config-if)#tun des 223.1.1.1 R3(config-if)#ip addres *Mar 1 18:59:07.740: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3(config-if)#ip addres 17.13.13.3 255.255.255.0 R3(config-if)#^Z R3# *Mar 1 18:59:18.506: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 18:59:23.714: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3# R3# R3# R3# R3# R3# RACK16AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets O 17.13.13.0 [110/11112] via 17.80.1.1, 00:00:03, FastEthernet0/0 C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11122] via 17.80.1.1, 00:00:03, FastEthernet0/0 R4# R4# R4# R4# R4# R4# R4# R4# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3# R3# R3# R3#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 17.80.1.1 YES manual up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 208.28.1.2 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.3 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--  Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down Virtual-Access1 unassigned YES unset up up Loopback0 222.1.1.3 YES manual up up Tunnel0 17.13.13.3 YES manual up up R3# R3# R3# R3# R3# R3# RACK16AS>1 [Resuming connection 1 to r1 ... ] * R1#sh run | b int interface Loopback0 ip address 223.1.1.1 255.255.255.0 ! interface Tunnel0 ip address 17.13.13.1 255.255.255.0 tunnel source Loopback0 tunnel destination 222.1.1.3 ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.240 frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 frame-relay interface-dlci 102 --More--  ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 half-duplex ! interface Serial0/1 no ip address shutdown ! router eigrp 100 network 180.40.7.64 0.0.0.31 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router ospf 1 router-id 1.1.1.1 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! router rip version 2 redistribute eigrp 100 metric 2 --More--   passive-interface Ethernet0/0 --More--   offset-list 1 out 5 --More--   network 208.28.1.0 --More--   network 223.1.1.0 --More--   neighbor 208.28.1.3 --More--   maximum-paths 3 --More--   no auto-summary --More--  ! --More--   R1# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b int interface Loopback0 ip address 222.1.1.3 255.255.255.0 ! interface Tunnel0 ip address 17.13.13.3 255.255.255.0 tunnel source Loopback0 tunnel destination 223.1.1.1 ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! --More--  interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 --More--   no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! router rip version 2 no validate-update-source --More--   timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! ! ! call rsvp-sync ! ! mgcp profile default ! ! --More--   R3# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 O 17.80.1.0 [110/11112] via 17.13.13.3, 00:01:50, Tunnel0 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:21, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 5 subnets, 4 masks D 208.28.1.192/31 [90/409600] via 208.28.1.65, 00:28:31, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:51:48, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/28 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:48:13, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks --More--  R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:23, Serial0/0.1 [120/1] via 208.28.1.3, 00:00:16, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:50:13, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11121] via 17.13.13.1, 00:02:28, Tunnel0 C 222.1.1.0/24 is directly connected, Loopback0 R 223.1.1.0/24 [120/1] via 208.28.1.1, 00:00:00, Serial1/0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks R 208.28.1.192/31 [120/7] via 180.40.7.2, 00:15:05, Serial1/2 [120/7] via 208.28.1.1, 00:00:00, Serial1/0 [120/7] via 208.28.1.3, 00:00:16, Serial1/0 R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:15:06, Serial1/2 [120/1] via 208.28.1.3, 00:00:16, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:01, Serial1/0 --More--   R3#ping 208.28.1.193 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.193, timeout is 2 seconds: !..!. Success rate is 40 percent (2/5), round-trip min/avg/max = 40/44/49 ms R3# RACK16AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router eigrp 100 R1(config-router)#redi R1(config-router)#redistribute rip me R1(config-router)#redistribute rip metric ? <1-4294967295> Bandwidth metric in Kbits per second R1(config-router)#redistribute rip metric 128 10000 255 1 1500 R1(config-router)#^Z R1# RACK16AS>2 [Resuming connection 2 to r2 ... ] * R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eigrp 100 R2(config-router)#redistribute rip metric 128 10000 255 1 1500 R2(config-router)#^Z R2# *Mar 1 19:03:17.077: %SYS-5-CONFIG_I: Configured from console by console R2# RACK16AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set D EX 222.1.1.0/24 [170/22560256] via 208.28.1.66, 00:00:09, Vlan10 [170/22560256] via 208.28.1.129, 00:00:09, Vlan20 D EX 223.1.1.0/24 [170/22560256] via 208.28.1.66, 00:00:09, Vlan10 [170/22560256] via 208.28.1.129, 00:00:09, Vlan20 208.28.1.0/24 is variably subnetted, 5 subnets, 4 masks C 208.28.1.192/31 is directly connected, Loopback0 C 208.28.1.128/27 is directly connected, Vlan20 C 208.28.1.64/28 is directly connected, Vlan10 D EX 208.28.1.0/29 [170/22560256] via 208.28.1.129, 00:00:09, Vlan20 D EX 208.28.1.0/28 [170/22560256] via 208.28.1.66, 00:00:24, Vlan10 D 180.40.0.0/16 [90/2170112] via 208.28.1.66, 00:52:10, Vlan10 S5# qq RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#ping 208.28.1.193 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.193, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/52/60 ms R3# R3# R3# R3# R3#ping 208.28.1.193 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.193, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 45/55/60 ms R3# RACK16AS>1 [Resuming connection 1 to r1 ... ] *Mar 1 19:04:06.298: R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 O 17.80.1.0 [110/11112] via 17.13.13.3, 00:04:03, Tunnel0 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:42, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D 208.28.1.192/31 [90/409600] via 208.28.1.65, 00:30:44, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:54:00, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 D EX 208.28.1.0/29 [170/22585856] via 208.28.1.65, 00:00:25, Ethernet0/0 C 208.28.1.0/28 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:50:26, Null0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:43, Serial0/0.1 [120/1] via 208.28.1.3, 00:00:09, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:52:24, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#ip addres 208.28.1.1 255.255.255.248 R1(config-subif)#^Z R1#config t *Mar 1 19:07:23.076: %SYS-5-CONFIG_I: Configured from console by consolesh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 O 17.80.1.0 [110/11112] via 17.13.13.3, 00:06:46, Tunnel0 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:05, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks D 208.28.1.192/31 [90/409600] via 208.28.1.65, 00:33:26, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:56:43, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:53:09, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks --More--  R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:07, Serial0/0.1 [120/1] via 208.28.1.3, 00:00:02, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:55:08, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#rouetr     ter rip R1(config-router)#rei dis R1(config-router)#redistribute ospf 1 met 3 R1(config-router)#router eigrp 100 R1(config-router)#router eigrp 100edistribute ospf 1 met 3 100000 1000 255 1 1500 R1(config-router)#routre ospf 1 ^ % Invalid input detected at '^' marker. R1(config-router)#rei  router         ru outer ospf 1 R1(config-router)#redis eigrp 100 sub R1(config-router)#redis rip sub R1(config-router)#^Z R1# RACK16AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router rip R3(config-router)#redis *Mar 1 19:08:13.391: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 19:08:14.392: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 19:08:14.392: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-router)#redis ospf 1 met 5 R3(config-router)#red   router ospf 1 R3(config-router)#tre   redsi    is rip sub R3(config-router)#^Z R3# *Mar 1 19:08:36.869: %SYS-5-CONFIG_I: Configured from console by console R3#deb ip ospf ? adj OSPF adjacency events database-timer OSPF database timer events OSPF events flood OSPF flooding hello OSPF hello events lsa-generation OSPF lsa generation mpls OSPF MPLS nsf OSPF non-stop forwarding events packet OSPF packets retransmission OSPF retransmission events spf OSPF spf tree OSPF database tree R3#deb ip ospf [ack ? % Unrecognized command R3#deb ip ospf [ack      pack ? R3#deb ip ospf pack OSPF packet debugging is on R3# *Mar 1 19:09:14.447: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3# *Mar 1 19:09:16.947: OSPF: rcv. v:2 t:5 l:64 rid:4.4.4.4 aid:0.0.0.0 chk:C4D4 aut:0 auk: from FastEthernet0/0 R3# *Mar 1 19:09:22.813: OSPF: rcv. v:2 t:1 l:48 rid:4.4.4.4 aid:0.0.0.0 chk:B9E9 aut:0 auk: from FastEthernet0/0 *Mar 1 19:09:24.067: OSPF: rcv. v:2 t:1 l:48 rid:1.1.1.1 aid:0.0.0.0 chk:E492 aut:0 auk: from Tunnel0 *Mar 1 19:09:24.119: OSPF: rcv. v:2 t:2 l:32 rid:1.1.1.1 aid:0.0.0.0 chk:9669 aut:0 auk: from Tunnel0 *Mar 1 19:09:24.219: OSPF: rcv. v:2 t:2 l:372 rid:1.1.1.1 aid:0.0.0.0 chk:90A5 aut:0 auk: from Tunnel0 *Mar 1 19:09:24.411: OSPF: rcv. v:2 t:2 l:32 rid:1.1.1.1 aid:0.0.0.0 chk:81D5 aut:0 auk: from Tunnel0 *Mar 1 19:09:24.451: OSPF: rcv. v:2 t:3 l:168 rid:1.1.1.1 aid:0.0.0.0 chk:36BE aut:0 auk: from Tunnel0 *Mar 1 19:09:24.475: OSPF: rcv. v:2 t:4 l:112 rid:1.1.1.1 aid:0.0.0.0 chk:44FE aut:0 auk: from Tunnel0 *Mar 1 19:09:24.487: OSPF: rcv. v:2 t:2 l:32 rid:1.1.1.1 aid:0.0.0.0 chk:81D4 aut:0 auk: from Tunnel0 R3# *Mar 1 19:09:24.487: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3# *Mar 1 19:09:25.132: OSPF: rcv. v:2 t:4 l:88 rid:1.1.1.1 aid:0.0.0.0 chk:6239 aut:0 auk: from Tunnel0 R3# *Mar 1 19:09:26.975: OSPF: rcv. v:2 t:5 l:84 rid:4.4.4.4 aid:0.0.0.0 chk:2A43 aut:0 auk: from FastEthernet0/0 *Mar 1 19:09:27.176: OSPF: rcv. v:2 t:5 l:264 rid:1.1.1.1 aid:0.0.0.0 chk:8DC4 aut:0 auk: from Tunnel0 R3#u *Mar 1 19:09:30.105: OSPF: rcv. v:2 t:4 l:88 rid:1.1.1.1 aid:0.0.0.0 chk:6235 aut:0 auk: from Tunnel0 R3#u all All possible debugging has been turned off R3#deb ip ospf ? adj OSPF adjacency events database-timer OSPF database timer events OSPF events flood OSPF flooding hello OSPF hello events lsa-generation OSPF lsa generation mpls OSPF MPLS nsf OSPF non-stop forwarding events packet OSPF packets retransmission OSPF retransmission events spf OSPF spf tree OSPF database tree R3#deb ip ospf lsa *Mar 1 19:09:43.446: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 19:09:44.448: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 19:09:44.448: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R3#deb ip ospf lsa OSPF summary lsa generation debugging is on R3# *Mar 1 19:09:49.649: OSPF: Start scanning for FA update *Mar 1 19:09:49.649: OSPF: End scanning, Elapsed time 0ms *Mar 1 19:09:50.290: OSPF: Generate external LSA 17.57.100.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000003 *Mar 1 19:09:50.290: OSPF: Generate external LSA 223.1.1.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000003 *Mar 1 19:09:50.290: OSPF: Generate external LSA 208.28.1.192, mask 255.255.255.254, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000003 *Mar 1 19:09:50.290: OSPF: Generate external LSA 208.28.1.128, mask 255.255.255.224, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000003 *Mar 1 19:09:50.294: OSPF: Generate external LSA 208.28.1.64, mask 255.255.255.240, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000003 *Mar 1 19:09:50.294: OSPF: Generate external LSA 208.28.1.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80 R3#000004 *Mar 1 19:09:50.294: OSPF: Generate external LSA 180.40.0.0, mask 255.255.0.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000003 *Mar 1 19:09:50.294: OSPF: Generate external LSA 180.40.7.64, mask 255.255.255.224, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000003 R3# *Mar 1 19:09:51.660: OSPF: Generate external LSA 17.13.13.0, mask 255.255.255.0, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000002 R3#u all All possible debugging has been turned off R3# *Mar 1 19:10:44.502: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3# *Mar 1 19:10:54.435: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3# *Mar 1 19:11:13.554: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 19:11:14.504: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 19:11:14.556: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R3#coni    ah s access         sh access % Ambiguous command: "sh access" R3#sh access s-li R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# *Mar 1 19:12:14.610: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3(config)#ace ce *Mar 1 19:12:24.450: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3(config)#access-list 1 *Mar 1 19:12:33.609: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 19:12:34.611: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 19:12:34.611: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R3(config)#access-list 1 den 222.1.1.0 R3(config)#access-list     1 per any R3(config)#router ospf 1 R3(config-router)#router ospf 1access-lis 1 per anyt 1 den 222.1.1.0 redis rip sub    suv baccess-list 1 den 222.1.1.0                             dis R3(config-router)#disy t R3(config-router)#distr R3(config-router)#distribute-list 1 out rip ? R3(config-router)#distribute-list 1 out rip R3(config-router)#^Z R3# *Mar 1 19:13:31.973: %SYS-5-CONFIG_I: Configured from console by console R3#config tsh access-li u all  *Mar 1 19:13:34.665: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3#u alldeb ip ospf lsa OSPF summary lsa generation debugging is on R3# *Mar 1 19:13:45.119: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3# *Mar 1 19:13:50.928: OSPF: Generate external LSA 222.1.1.0, mask 255.255.255.0, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000002 R3# *Mar 1 19:14:00.123: OSPF: Generate external LSA 17.57.100.0, mask 255.255.255.0, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000008 *Mar 1 19:14:00.127: OSPF: Generate external LSA 180.40.0.0, mask 255.255.0.0, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000008 *Mar 1 19:14:00.127: OSPF: Generate external LSA 180.40.7.64, mask 255.255.255.224, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000008 *Mar 1 19:14:00.127: OSPF: Generate external LSA 208.28.1.0, mask 255.255.255.0, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000009 R3# *Mar 1 19:14:00.131: OSPF: Generate external LSA 208.28.1.64, mask 255.255.255.240, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000008 *Mar 1 19:14:00.131: OSPF: Generate external LSA 208.28.1.128, mask 255.255.255.224, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000008 *Mar 1 19:14:00.131: OSPF: Generate external LSA 208.28.1.192, mask 255.255.255.254, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000008 *Mar 1 19:14:00.131: OSPF: Generate external LSA 223.1.1.0, mask 255.255.255.0, type 5, age 3600, metric 16777215, tag 0, metric-type 2, seq 0x80000008 R3# *Mar 1 19:14:03.717: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 19:14:04.667: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 19:14:04.719: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 19:14:04.739: OSPF: Generate external LSA 17.13.13.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000001 *Mar 1 19:14:04.743: OSPF: Generate external LSA 17.57.100.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000001 *Mar 1 19:14:04.743: OSPF: Generate external LSA 223.1.1.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000001 *Mar 1 19:14:04.743: OSPF: Generate external LSA 208.28.1.192, mask 255.255.255.254, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000001 *Mar 1 19:14:04.743: OSPF: Generate external LSA 208.28.1.128, mask 255.255.2 R3#55.224, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000001 *Mar 1 19:14:04.747: OSPF: Generate external LSA 208.28.1.64, mask 255.255.255.240, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000001 *Mar 1 19:14:04.747: OSPF: Generate external LSA 208.28.1.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000001 *Mar 1 19:14:04.747: OSPF: Generate external LSA 180.40.0.0, mask 255.255.0.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000001 *Mar 1 19:14:04.751: OSPF: Generate external LSA 180.40.7.64, mask 255.255.255.224, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000001 R3# *Mar 1 19:14:10.124: OSPF: Start scanning for FA update *Mar 1 19:14:10.128: OSPF: End scanning, Elapsed time 4ms *Mar 1 19:14:10.384: OSPF: Generate external LSA 17.57.100.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000009 *Mar 1 19:14:10.384: OSPF: Generate external LSA 223.1.1.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000009 *Mar 1 19:14:10.384: OSPF: Generate external LSA 208.28.1.192, mask 255.255.255.254, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000009 *Mar 1 19:14:10.384: OSPF: Generate external LSA 208.28.1.128, mask 255.255.255.224, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000009 *Mar 1 19:14:10.388: OSPF: Generate external LSA 208.28.1.64, mask 255.255.255.240, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000009 *Mar 1 19:14:10.388: OSPF: Generate external LSA 208.28.1.0, mask 255.255.255.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80 R3#00000A *Mar 1 19:14:10.388: OSPF: Generate external LSA 180.40.0.0, mask 255.255.0.0, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000009 *Mar 1 19:14:10.388: OSPF: Generate external LSA 180.40.7.64, mask 255.255.255.224, type 5, age 0, metric 20, tag 0, metric-type 2, seq 0x80000009 R3#u all All possible debugging has been turned off R3# RACK16AS>`1 % Unknown command or computer name, or unable to find computer address RACK16AS>1 [Resuming connection 1 to r1 ... ] *M R1#s hip route show hip route ^ % Invalid input detected at '^' marker. R1#sh ip routew  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 O 17.80.1.0 [110/11112] via 17.13.13.3, 00:00:24, Tunnel0 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:08, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks D 208.28.1.192/31 [90/409600] via 208.28.1.65, 00:41:25, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 01:04:42, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 01:01:07, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks --More--  O E2 180.40.7.0/27 [110/20] via 17.13.13.3, 00:00:26, Tunnel0 D 180.40.0.0/16 is a summary, 00:00:26, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# *Mar 1 19:15:43.140: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired R1# R1# R1# RACK16AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip route *Mar 1 19:15:14.493: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf 17.0.0.0/24 is subnetted, 3 subnets O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:00, Tunnel0 O E2 223.1.1.0/24 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks O E2 208.28.1.192/31 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 O E2 208.28.1.128/27 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 O E2 208.28.1.64/28 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 O E2 208.28.1.0/24 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks O E2 180.40.0.0/16 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 O E2 180.40.7.64/27 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 R3#sh ip route ospf *Mar 1 19:15:23.772: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 19:15:24.774: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 19:15:24.774: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R3#sh ip route ospf R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router ospf 1 R3(config-router)#di R3(config-router)#dist R3(config-router)#distan R3(config-router)#distance ? <1-255> Administrative distance ospf OSPF distance R3(config-router)#distance ospf ? external External type 5 and type 7 routes inter-area Inter-area routes intra-area Intra-area routes R3(config-router)#distance ospf ex R3(config-router)#distance ospf external ? <1-255> Distance for external type 5 and type 7 routes R3(config-router)#distance ospf external 130 R3(config-router)#^Z R3#config t *Mar 1 19:16:16.683: %SYS-5-CONFIG_I: Configured from console by console R3#config t gtsh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3# *Mar 1 19:16:24.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3# *Mar 1 19:16:34.604: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf 17.0.0.0/24 is subnetted, 3 subnets O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:00, Tunnel0 R3#sh ip route ospf 17.0.0.0/24 is subnetted, 3 subnets O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:01, Tunnel0 R3#sh ip route ospf 17.0.0.0/24 is subnetted, 3 subnets O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:03, Tunnel0 R3#sh ip route ospf 17.0.0.0/24 is subnetted, 3 subnets O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:04, Tunnel0 R3#sh ip route ospf 17.0.0.0/24 is subnetted, 3 subnets O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:10, Tunnel0 R3#sh run | b router ospf router ospf 1 router-id 3.3.3.3 log-adjacency-changes redistribute rip subnets network 17.0.0.0 0.255.255.255 area 0 distribute-list 1 out rip distance ospf external 130 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 redistribute ospf 1 metric 5 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! no ip http server no ip http secure-server --More--  ip classless ! ! ! access-list 1 deny 222.1.1.0 access-list 1 permit any ! ! call rsvp-sync ! ! mgcp profile default ! ! ! dial-peer cor custom ! ! ! ! ! line con 0 exec-timeout 0 0 --More--   R3#confi gt ^ % Invalid input detected at '^' marker. R3#coni fig t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router ospf 1 R3(config-router)#router ospf 1distance ospf external 130ndistance ospf external 130odistance ospf external 130 distance ospf external 130 R3(config-router)#exit R3(config)#access-list 2 *Mar 1 19:17:53.882: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 19:17:54.844: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 19:17:54.884: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R3(config)#access-list 2 per 223.1.1.0 R3(config)#router ospf 1 R3(config-router)#distan R3(config-router)#distance 130 1.1.1.1             ? <1-255> Administrative distance ospf OSPF distance R3(config-router)#distance 130 ? A.B.C.D IP Source address R3(config-router)#distance 130 1.1.1.1 ? A.B.C.D IP address mask R3(config-router)#distance 130 1.1.1.1 0.0.0.0 *Mar 1 19:18:54.942: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3(config-router)#distance 130 1.1.1.1 0.0.0.0 ? <1-99> IP Standard access list number <1300-1999> IP Standard expanded access list number WORD Standard access-list name R3(config-router)#distance 130 1.1.1.1 0.0.0.0 2 R3(config-router)#^Z R3# *Mar 1 19:19:01.185: %SYS-5-CONFIG_I: Configured from console by console R3#config t gtsh run | b router ospf ip route ospf  *Mar 1 19:19:04.638: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf R3#sh ip route ospf 17.0.0.0/24 is subnetted, 3 subnets O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:00, Tunnel0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks O E2 208.28.1.192/31 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 O E2 208.28.1.128/27 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 O E2 208.28.1.64/28 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 O E2 208.28.1.0/24 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks O E2 180.40.0.0/16 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 O E2 180.40.7.64/27 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 R3# R3# R3# R3# R3#sh ip route ospf 17.0.0.0/24 is subnetted, 3 subnets O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:06, Tunnel0 208.28.1.0/24 is variably subnetted, 5 subnets, 5 masks O E2 208.28.1.192/31 [110/20] via 17.13.13.1, 00:00:06, Tunnel0 O E2 208.28.1.128/27 [110/20] via 17.13.13.1, 00:00:06, Tunnel0 O E2 208.28.1.64/28 [110/20] via 17.13.13.1, 00:00:06, Tunnel0 O E2 208.28.1.0/24 [110/20] via 17.13.13.1, 00:00:06, Tunnel0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks O E2 180.40.0.0/16 [110/20] via 17.13.13.1, 00:00:06, Tunnel0 O E2 180.40.7.64/27 [110/20] via 17.13.13.1, 00:00:06, Tunnel0 R3#sh ip ospf data OSPF Router with ID (3.3.3.3) (Process ID 1) Router Link States (Area 0) Link ID ADV Router Age Seq# Checksum Link count 1.1.1.1 1.1.1.1 34 0x80000016 0x004AB9 3 3.3.3.3 3.3.3.3 34 0x8000001A 0x00FA9C 3 4.4.4.4 4.4.4.4 1736 0x80000002 0x0078D0 1 6.6.6.6 6.6.6.6 1767 0x80000002 0x009C04 1 Net Link States (Area 0) Link ID ADV Router Age Seq# Checksum 17.57.100.2 6.6.6.6 1768 0x80000001 0x00F85C 17.80.1.2 4.4.4.4 1737 0x80000001 0x008524 Type-5 AS External Link States Link ID ADV Router Age Seq# Checksum Tag 180.40.0.0 1.1.1.1 703 0x80000001 0x00BA05 0 180.40.7.0 3.3.3.3 663 0x80000001 0x007659 0 180.40.7.64 1.1.1.1 703 0x80000001 0x003067 0 --More--  208.28.1.0 1.1.1.1 703 0x80000001 0x00D2DB 0 208.28.1.7 1.1.1.1 694 0x80000001 0x00624C 0 208.28.1.7 3.3.3.3 664 0x80000001 0x002680 0 208.28.1.64 1.1.1.1 704 0x80000001 0x00F587 0 208.28.1.128 1.1.1.1 704 0x80000001 0x00133A 0 208.28.1.192 1.1.1.1 704 0x80000001 0x0045A9 0 222.1.1.0 1.1.1.1 416 0x80000007 0x005560 0 223.1.1.0 1.1.1.1 694 0x80000001 0x005466 0 223.1.1.0 3.3.3.3 99 0x8000000D 0x00FFA6 0 R3#  sh run | b router ospf router ospf 1 router-id 3.3.3.3 log-adjacency-changes redistribute rip subnets network 17.0.0.0 0.255.255.255 area 0 distribute-list 1 out rip distance 130 1.1.1.1 0.0.0.0 2 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 redistribute ospf 1 metric 5 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! no ip http server no ip http secure-server --More--   R3#sh run | b router ospf router ospf 1 router-id 3.3.3.3 log-adjacency-changes redistribute rip subnets network 17.0.0.0 0.255.255.255 area 0 distribute-list 1 out rip distance 130 1.1.1.1 0.0.0.0 2 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 redistribute ospf 1 metric 5 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! no ip http server no ip http secure-server --More--  ip classless ! ! ! access-list 1 deny 222.1.1.0 access-list 1 permit any access-list 2 permit 223.1.1.0 ! ! call rsvp-sync ! ! mgcp profile default ! ! ! dial-peer cor custom ! ! ! ! ! line con 0 --More--   R3# [Connection to r3 closed by foreign host] RACK16AS>