=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.02.14 13:21:49 =~=~=~=~=~=~=~=~=~=~=~= RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#ping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/60 ms R1#ping 208.28.1.2 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s 0/0\    1/0.1 Building configuration... Current configuration : 111 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay interface-dlci 203 end R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)#no frame-relay interface-dlci 203 R2(config-subif)#fram map ip 208.29 8.1.2 203 R2(config-subif)#fram map ip 208.28.1.2 203  203 1 203  R2(config-subif)# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#ping 208.28.1.323 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/114/116 ms R1# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/0 Building configuration... Current configuration : 178 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 end R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2(config-subif)#^Z R2# *Mar 1 03:15:12.330: %SYS-5-CONFIG_I: Configured from console by console R2#sh run int s 1/0.1 Building configuration... Current configuration : 149 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 end R2# R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eigrp 100 R2(config-router)#no auto R2(config-router)#net 208.28.1.3 0.0.0.0 R2(config-router)#nei R2(config-router)#neighbor ? A.B.C.D Neighbor address R2(config-router)#neighbor 208.28.1.2 ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config-router)#neighbor 208.28.1.2 ser R2(config-router)#neighbor 208.28.1.2 serial 1/0.1 ? R2(config-router)#neighbor 208.28.1.2 serial 1/0.1 R2(config-router)#^Z R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router bg   eigrp 100 R3(config-router)#no auto R3(config-router)#net 208.28.1.2 0.0.0.0 R3(config-router)#ni ei R3(config-router)#neighbor 208.28.1.1 % Incomplete command. R3(config-router)#neighbor 208.28.1.1t 208.28.1.2 0.0.0.0ighbor 208.28.1.1  ser 1/0 R3(config-router)#~neighbor 208.28.1.1 ser 1/0 ser 1/0 3 ser 1/0 R3(config-router)# *Mar 1 03:20:39.963: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.3 (Serial1/0) is up: new adjacency R3(config-router)#^Z R3# *Mar 1 03:20:43.553: %SYS-5-CONFIG_I: Configured from console by console R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#rouetr bgp         ter eigrp 100 R1(config-router)#no auto R1(config-router)#nei t 208.28.1.1 0.0.0.0 R1(config-router)#nei 208.28.1.2 ser 0 0/0.1 R1(config-router)# *Mar 1 03:22:11.310: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial0/0.1) is up: new adjacency R1(config-router)#^Z R1# *Mar 1 03:22:13.245: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se0/0.1 158 00:02:16 1 3000 0 2 R1# R1# R1# R1# R1# R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do shj    ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 R1(config)#router eigrp 100 R1(config-router)#net 17.57.100.1 - 0.0.0.0 R1(config-router)#net 17.57.100.1 0.0.0.0 net 17.57.100.1 0.0.0.0 R1(config-router)#^Z R1# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#neighbor 208.28.1.3 ser 1/01 ser 1/0 t 208.28.1.2 0.0.0.0o auto router eigrp 100 R3(config-router)#net 17.80.1.1 0.0.0.0 R3(config-router)#^Z R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 D 17.57.100.0 [90/20537600] via 208.28.1.1, 00:00:24, Serial1/0 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0 R3# *Mar 1 03:27:39.507: %SYS-5-CONFIG_I: Configured from console by console R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh ip rotue ^ % Invalid input detected at '^' marker. R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets D 17.80.1.0 [90/2172416] via 208.28.1.2, 00:00:35, Serial0/0.1 C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 R2#sdh ip       h ipo route ^ % Invalid input detected at '^' marker. R2#sh ipo route route  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets D 17.80.1.0 [90/20514560] via 208.28.1.2, 00:00:46, Serial1/0.1 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0.1 R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eigrp 100 R2(config-router)#nei 208.28.1.1 ser 1/0.1 R2(config-router)# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router eigrp 100 R1(config-router)#nei 208.28.1.3 x ser 0/0.1 R1(config-router)#^Z R1# *Mar 1 03:30:03.023: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se0/0.1 148 00:08:01 40 240 0 4 R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se0/0.1 142 00:08:06 40 240 0 4 R1#ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/114/116 ms R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] *M R2(config-router)#nei 208.28.1.1 ser 1/0.1 ^Z R2# *Mar 1 03:29:47.337: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 208.28.1.1 Se1/0.1 13 00:00:48 1 5000 2 4 0 208.28.1.2 Se1/0.1 177 00:08:40 237 1422 0 4 R2#sh fram map Serial1/0.1 (up): ip 208.28.1.1 dlci 203(0xCB,0x30B0), static, CISCO, status defined, active Serial1/0.1 (up): ip 208.28.1.2 dlci 203(0xCB,0x30B0), static, CISCO, status defined, active R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#deb i eigrp % Incomplete command. R1#deb eigrp pack EIGRP Packets debugging is on (UPDATE, REQUEST, QUERY, REPLY, HELLO, IPXSAP, PROBE, ACK, STUB, SIAQUERY, SIAREPLY) R1# *Mar 1 03:31:40.715: EIGRP: Sending HELLO on Ethernet0/1 *Mar 1 03:31:40.715: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:40.943: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.3 *Mar 1 03:31:40.943: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:40.943: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.2 *Mar 1 03:31:40.943: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1# *Mar 1 03:31:44.549: EIGRP: Received HELLO on Serial0/0.1 nbr 208.28.1.3 *Mar 1 03:31:44.549: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/0 *Mar 1 03:31:45.254: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.3 *Mar 1 03:31:45.254: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:45.254: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.2 *Mar 1 03:31:45.254: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:45.527: EIGRP: Sending HELLO on Ethernet0/1 *Mar 1 03:31:45.527: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1# *Mar 1 03:31:49.726: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.3 *Mar 1 03:31:49.726: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:49.726: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.2 *Mar 1 03:31:49.726: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:50.014: EIGRP: Sending HELLO on Ethernet0/1 *Mar 1 03:31:50.014: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1# *Mar 1 03:31:54.213: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.3 *Mar 1 03:31:54.213: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:54.213: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.2 *Mar 1 03:31:54.213: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:54.686: EIGRP: Sending HELLO on Ethernet0/1 *Mar 1 03:31:54.686: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1#u all All possible debugging has been turned off R1# *Mar 1 03:31:58.572: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.3 *Mar 1 03:31:58.572: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:58.572: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.2 *Mar 1 03:31:58.572: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:31:59.121: EIGRP: Sending HELLO on Ethernet0/1 *Mar 1 03:31:59.121: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1#sh ip eigr nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 208.28.1.3 Se0/0.1 161 00:01:14 1 3000 0 4 0 208.28.1.2 Se0/0.1 152 00:09:52 40 240 0 4 R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh fram mapip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 208.28.1.1 Se1/0.1 12 00:02:06 73 1140 0 4 0 208.28.1.2 Se1/0.1 146 00:09:58 237 1422 0 4 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets D 17.80.1.0 [90/20514560] via 208.28.1.2, 00:03:53, Serial1/0.1 D 17.57.100.0 [90/20537600] via 208.28.1.1, 00:01:35, Serial1/0.1 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0.1 R2#sh run | b router bg    eip grp router eigrp 100 network 208.28.1.3 0.0.0.0 neighbor 208.28.1.1 Serial1/0.1 neighbor 208.28.1.2 Serial1/0.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous --More--   R2#^x1 % Unknown command or computer name, or unable to find computer address R2# R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b router router eigrp 100 network 17.57.100.1 0.0.0.0 network 208.28.1.1 0.0.0.0 neighbor 208.28.1.3 Serial0/0.1 neighbor 208.28.1.2 Serial0/0.1 no auto-summary ! no ip http server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! --More--   R1#^x3 % Unknown command or computer name, or unable to find computer address R1# R1#^x3 % Unknown command or computer name, or unable to find computer address R1# R1# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b router router eigrp 100 network 17.80.1.1 0.0.0.0 network 208.28.1.2 0.0.0.0 neighbor 208.28.1.3 Serial1/0 neighbor 208.28.1.1 Serial1/0 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 --More--   R3#^x1 % Unknown command or computer name, or unable to find computer address R3# R3# RACK9AS>co  q (You have open connections) [confirm]^C RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#confifg t ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#in  nei 208.28.1.3 ser 0/0.1router eigrp 100  R1(config-router)#router eigrp 100nei 208.28.1.3 ser 0/0.1nnei 208.28.1.3 ser 0/0.1onei 208.28.1.3 ser 0/0.1 nei 208.28.1.3 ser 0/0.1 R1(config-router)# *Mar 1 03:34:59.533: %DUAL-5-NBRCHANG RACK9AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#nei 208.28.1.1 ser 1/0.1router eigrp 100  R2(config-router)#router eigrp 100nei 208.28.1.1 ser 1/0.1nnei 208.28.1.1 ser 1/0.1onei 208.28.1.1 ser 1/0.1 nei 208.28.1.1 ser 1/0.1 R2(config-router)#^Z R2# *Mar 1 03:34:09.655: %SYS-5-CONFIG_I: Configured from console by console R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#no ip sp R3(config-if)#no ip split-horizon ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) R3(config-if)#no ip split-horizon ei R3(config-if)#no ip split-horizon eigrp ? <1-65535> Autonomous system number R3(config-if)#no ip split-horizon eigrp 1000  ? R3(config-if)#no ip split-horizon eigrp 100 R3(config-if)# *Mar 1 03:34:41.383: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.1 (Serial1/0) is down: split horizon changed *Mar 1 03:34:41.383: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.3 (Serial1/0) is down: split horizon changed *Mar 1 03:34:41.872: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.3 (Serial1/0) is up: new adjacency R3(config-if)# *Mar 1 03:34:45.257: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.1 (Serial1/0) is up: new adjacency R3(config-if)#^Z R3# *Mar 1 03:34:49.196: %SYS-5-CONFIG_I: Configured from console by console R3#^x2 % Unknown command or computer name, or unable to find computer address R3# R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0.1 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0.1 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0.1 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0.1 R2#sh ip eigrp neri  i IP-EIGRP neighbors for process 100 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 179 00:00:00 1 2000 1 0 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 179 00:00:00 1 2000 1 0 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 179 00:00:00 1 2000 1 0 R2# *Mar 1 03:35:29.994: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial1/0.1) is up: new adjacency R2# R2# R2# R2#sh ip eigrp neiroute  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets D 17.80.1.0 [90/20514560] via 208.28.1.2, 00:00:01, Serial1/0.1 D 17.57.100.0 [90/21049600] via 208.28.1.2, 00:00:01, Serial1/0.1 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0.1 R2#^x  [29~x      RACK9AS>1 [Resuming connection 1 to r1 ... ] E: IP-EIGRP(0) 100: Neighbor 208.28.1.3 (Serial0/0.1) is down: R1(config-router)# R1(config-router)#^Z R1#sh ip *Mar 1 03:36:56.368: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets D 17.80.1.0 [90/2172416] via 208.28.1.2, 00:00:26, Serial0/0.1 C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 R1#sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.66) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 17.80.1.0/24, 1 successors, FD is 2172416, serno 4 via 208.28.1.2 (2172416/28160), Serial0/0.1 P 17.57.100.0/24, 1 successors, FD is 281600, serno 2 via Connected, Ethernet0/1 via 208.28.1.2 (21049600/20537600), Serial0/0.1 P 208.28.1.0/29, 1 successors, FD is 2169856, serno 1 via Connected, Serial0/0.1 via 208.28.1.2 (21024000/20512000), Serial0/0.1 R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#access      ip pr R1(config)#ip prefix-list ? WORD Name of a prefix list sequence-number Include/exclude sequence numbers in NVGEN R1(config)#ip prefix-list Prob2 ? deny Specify packets to reject description Prefix-list specific description permit Specify packets to forward seq sequence number of an entry R1(config)#ip prefix-list Prob2 deny ? A.B.C.D IP prefix /, e.g., 35.0.0.0/8 R1(config)#ip prefix-list Prob2 deny 17.57.100.0/24 R1(config)#ip prefix-list Prob2 deny 17.57.100.0/24                   deny 208.28.1.0/29 R1(config)#ip prefix-list Prob2 deny 208.28.1.0/29                  per any ^ % Invalid input detected at '^' marker. R1(config)#ip prefix-list Prob2 per any   00.0.0.0.0.00.0.0/0 le 32 R1(config)#rotuer eigrp 100 ^ % Invalid input detected at '^' marker. R1(config)#rotuer eigrp 100er eigrp 100 er eigrp 100 uer eigrp 100ter eigrp 100 R1(config-router)#di  pr R1(config-router)#pr? % Unrecognized command R1(config-router)#pr  di R1(config-router)#distr R1(config-router)#distribute-list ? <1-199> IP access list number <1300-2699> IP expanded access list number WORD Access-list name gateway Filtering incoming updates based on gateway prefix Filter prefixes in routing updates R1(config-router)#distribute-list pre R1(config-router)#distribute-list prefix ? WORD Name of an IP prefix-list R1(config-router)#distribute-list prefix Prob2 ? gateway Filtering incoming updates based on gateway in Filter incoming routing updates out Filter outgoing routing updates R1(config-router)#distribute-list prefix Prob2 in ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface Ethernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R1(config-router)#distribute-list prefix Prob2 in ser 0/0.1 R1(config-router)# *Mar 1 03:41:57.486: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial0/0.1) is down: route configuration changed R1(config-router)# *Mar 1 03:42:03.264: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial0/0.1) is up: new adjacency R1(config-router)#^Z R1# *Mar 1 03:42:19.923: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se0/0.1 158 00:00:22 631 3786 0 11 R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets D 17.80.1.0 [90/2172416] via 208.28.1.2, 00:00:25, Serial0/0.1 C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 R1#sh ip routeeigrp neiconfig t sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.66) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 17.80.1.0/24, 1 successors, FD is 2172416, serno 5 via 208.28.1.2 (2172416/28160), Serial0/0.1 P 17.57.100.0/24, 1 successors, FD is 281600, serno 2 via Connected, Ethernet0/1 P 208.28.1.0/29, 1 successors, FD is 2169856, serno 1 via Connected, Serial0/0.1 R1# R1# R1# R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#access-list 100 per ip 208.28.1.0 0.0.0.0 255.255.2555.  .248 0.0.0.0 ip 208.28.1.0 0.0.0.0 255.255.255.248 0.0.0.0  ip 208.28.1.0 0.0.0.0 255.255.255.248 0.0.0.0  ip 208.28.1.0 0.0.0.0 255.255.255.248 0.0.0.0 d ip 208.28.1.0 0.0.0.0 255.255.255.248 0.0.0.0e ip 208.28.1.0 0.0.0.0 255.255.255.248 0.0.0.0n ip 208.28.1.0 0.0.0.0 255.255.255.248 0.0.0.0y ip 208.28.1.0 0.0.0.0 255.255.255.248 0.0.0.0 R2(config)#access-list 100 per ip any ay ny R2(config)#router eigrp 100 R2(config-router)#do istr R2(config-router)#distribute-list ? <1-199> IP access list number <1300-2699> IP expanded access list number WORD Access-list name gateway Filtering incoming updates based on gateway prefix Filter prefixes in routing updates R2(config-router)#distribute-list 100 in s 1/0.1 R2(config-router)#^Z R2#sh ip *Mar 1 03:43:14.368: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 17.80.1.0/24, 1 successors, FD is 20514560, serno 5 via 208.28.1.2 (20514560/28160), Serial1/0.1 P 17.57.100.0/24, 1 successors, FD is 21049600, serno 8 via 208.28.1.2 (21049600/20537600), Serial1/0.1 P 208.28.1.0/29, 1 successors, FD is 20512000, serno 1 via Connected, Serial1/0.1 via 208.28.1.2 (21024000/20512000), Serial1/0.1 R2# *Mar 1 03:43:20.333: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial1/0.1) is down: route configuration changed R2#sh ip eigrp top allconfig t sh ip routeeigrp nei IP-EIGRP neighbors for process 100 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 R2# *Mar 1 03:43:45.939: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial1/0.1) is up: new adjacency R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 176 00:00:03 1 3000 1 0 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 174 00:00:05 1 4500 1 0 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 172 00:00:07 1 4500 1 0 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 171 00:00:08 1 4500 1 0 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 169 00:00:10 1 5000 1 0 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 168 00:00:11 1 5000 1 0 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 163 00:00:16 1 5000 1 0 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 157 00:00:22 1 5000 1 0 R2#sh run | b router router eigrp 100 network 208.28.1.3 0.0.0.0 neighbor 208.28.1.2 Serial1/0.1 distribute-list 100 in Serial1/0.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 100 deny ip host 208.28.1.0 host 255.255.255.248 access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 --More--   R2#sh run | b routerip eigrp nei  IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 160 00:00:54 48 1140 0 12 R2#sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 17.80.1.0/24, 1 successors, FD is 20514560, serno 9 via 208.28.1.2 (20514560/28160), Serial1/0.1 P 17.57.100.0/24, 1 successors, FD is 21049600, serno 10 via 208.28.1.2 (21049600/20537600), Serial1/0.1 P 208.28.1.0/29, 1 successors, FD is 20512000, serno 1 via Connected, Serial1/0.1 via 208.28.1.2 (21024000/20512000), Serial1/0.1 R2#q config ty ^ % Invalid input detected at '^' marker. R2#config ty  Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eigrp 100 R2(config-router)#~router eigrp 100distribute-list 100 in s 1/0.1         R2(config-router)#do sh run | b rout *Mar 1 03:47:45.829: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial1/0.1) is down: route configuration changed R2(config-router)#do sh run | b router ei router eigrp 100 network 208.28.1.3 0.0.0.0 neighbor 208.28.1.2 Serial1/0.1 distribute-list 100 in Serial1/0.1 distribute-list 100 in no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 100 deny ip host 208.28.1.0 host 255.255.255.248 access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! --More--   R2(config-router)#no distribute-list 100 in Serial1/0.1 R2(config-router)#no distribute-list 100 in Serial1/0.1do sh run | b router ei  router eigrp 100 network 208.28.1.3 0.0.0.0 neighbor 208.28.1.2 Serial1/0.1 distribute-list 100 in no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 100 deny ip host 208.28.1.0 host 255.255.255.248 access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 --More--   R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 R2(config-router)# *Mar 1 03:48:37.305: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial1/0.1) is up: new adjacency R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 178 00:00:03 1594 5000 0 13 R2(config-router)#do sh ip eigrp neirun | b router eiip eigrp nei run | b router eiip eigrp nei    top[    all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 17.80.1.0/24, 1 successors, FD is 20514560, serno 11 via 208.28.1.2 (20514560/28160), Serial1/0.1 P 17.57.100.0/24, 1 successors, FD is 21049600, serno 12 via 208.28.1.2 (21049600/20537600), Serial1/0.1 P 208.28.1.0/29, 1 successors, FD is 20512000, serno 1 via Connected, Serial1/0.1 via 208.28.1.2 (21024000/20512000), Serial1/0.1 R2(config-router)#sh run int s 1./0   /0.1 ^ % Invalid input detected at '^' marker. R2(config-router)#sh run int s 1/0.1dsh run int s 1/0.1osh run int s 1/0.1 sh run int s 1/0.1 Building configuration... Current configuration : 149 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 end R2(config-router)#exit\ ^ % Invalid input detected at '^' marker. R2(config-router)#exit\  R2(config)#ip pre R2(config)#ip prefix-list Prob2 deny 208.28.1.0/29 ~  R2(config)#ip prefix-list Prob2 deny 208.28.1.0/29                       b2 per 0.0.0.0/0 le 32 R2(config)#router i eigrp 100 R2(config-router)#distr li    R2(config-router)#distribute-list pre R2(config-router)#distribute-list prefix Prob2 in s 1/0.1 R2(config-router)#distribute-list prefix Prob2 in s 1/0.1router eigrp 100 ip prefix-list Prob2 per 0.0.0.0/0 le 32deny 208.28.1.0/29 exit \do sh run int s 1/0.1sh run int s 1/0.1 do sh ip eigrp top allnei run | b router eino distribute-list 100 in Serial1/0.1 *Mar 1 03:50:49.706: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial1/0.1) is down: route configuration changed R2(config-router)#no distribute-list 100 in Serial1/0.1            R2(config-router)#do sh run | b rouert R2(config-router)#do sh run | b rouert   ter router eigrp 100 network 208.28.1.3 0.0.0.0 neighbor 208.28.1.2 Serial1/0.1 distribute-list prefix Prob2 in Serial1/0.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ip prefix-list Prob2 seq 5 deny 208.28.1.0/29 ip prefix-list Prob2 seq 10 permit 0.0.0.0/0 le 32 access-list 100 deny ip host 208.28.1.0 host 255.255.255.248 access-list 100 permit ip any any ! ! ! ! ! ! ! --More--   R2(config-router)#do sh run | b routerertno distribute-list 100 in distribute-list prefix Prob2 in s 1/0.1router eigrp 100 ip prefix-list Prob2 per 0.0.0.0/0 le 32deny 208.28.1.0/29 *Mar 1 03:51:28.802: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial1/0.1) is up: new adjacency R2(config-router)#ip prefix-list Prob2 deny 208.28.1.0/29 exit \do sh run int s 1/0.1sh run int s 1/0.1 do sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 208.28.1.0/29, 1 successors, FD is 20512000, serno 1, anchored via Connected, Serial1/0.1 R2(config-router)#do sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 208.28.1.0/29, 1 successors, FD is 20512000, serno 1, anchored via Connected, Serial1/0.1 R2(config-router)#do sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 208.28.1.0/29, 1 successors, FD is 20512000, serno 1, anchored via Connected, Serial1/0.1 R2(config-router)#do sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 208.28.1.0/29, 1 successors, FD is 20512000, serno 1, anchored via Connected, Serial1/0.1 R2(config-router)#do sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 17.80.1.0/24, 1 successors, FD is 20514560, U, serno 13, refcount 1, anchored via 208.28.1.2 (20514560/28160), Serial1/0.1 P 17.57.100.0/24, 1 successors, FD is 21049600, U, serno 14, refcount 1 via 208.28.1.2 (21049600/20537600), Serial1/0.1 P 208.28.1.0/29, 1 successors, FD is 20512000, serno 1, anchored via Connected, Serial1/0.1 R2(config-router)#do sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.3) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 17.80.1.0/24, 1 successors, FD is 20514560, U, serno 13, refcount 1, anchored via 208.28.1.2 (20514560/28160), Serial1/0.1 P 17.57.100.0/24, 1 successors, FD is 21049600, U, serno 14, refcount 1 via 208.28.1.2 (21049600/20537600), Serial1/0.1 P 208.28.1.0/29, 1 successors, FD is 20512000, serno 1, anchored via Connected, Serial1/0.1 R2(config-router)#^Z R2# *Mar 1 03:52:33.797: %SYS-5-CONFIG_I: Configured from console by console R2#sh ver Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller Image text-base: 0x80008098, data-base: 0x8202B100 ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) ROM: C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) R2 uptime is 3 hours, 52 minutes System returned to ROM by power-on System image file is "flash:c2600-adventerprisek9-mz.123-16a.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you --More--  agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco 2611XM (MPC860P) processor (revision 0x400) with 126976K/4096K bytes of memory. Processor board ID JMX0848L2HF (1238400631) M860 processor: part number 5, mask 2 X.25 software, Version 3.0.0. SuperLAT software (copyright 1990 by Meridian Technology Corp). Bridging software. TN3270 Emulation software. Basic Rate ISDN software, Version 1.1. 2 FastEthernet/IEEE 802.3 interface(s) 8 Low-speed serial(sync/async) network interface(s) 1 ISDN Basic Rate interface(s) 32K bytes of non-volatile configuration memory. 49152K bytes of processor board System flash (Read/Write) --More--   R2#sh run |          ^x1 % Unknown command or computer name, or unable to find computer address R2# R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b router router eigrp 100 network 17.57.100.1 0.0.0.0 network 208.28.1.1 0.0.0.0 neighbor 208.28.1.2 Serial0/0.1 distribute-list prefix Prob2 in Serial0/0.1 no auto-summary ! no ip http server ip classless ! ! ! ip prefix-list Prob2 seq 5 deny 17.57.100.0/24 ip prefix-list Prob2 seq 10 deny 208.28.1.0/29 ip prefix-list Prob2 seq 15 permit 0.0.0.0/0 le 32 ! ! ! ! ! ! line con 0 exec-timeout 0 0 --More--   R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b router router eigrp 100 network 208.28.1.3 0.0.0.0 neighbor 208.28.1.2 Serial1/0.1 distribute-list prefix Prob2 in Serial1/0.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ip prefix-list Prob2 seq 5 deny 208.28.1.0/29 ip prefix-list Prob2 seq 10 permit 0.0.0.0/0 le 32 access-list 100 deny ip host 208.28.1.0 host 255.255.255.248 access-list 100 permit ip any any ! ! ! ! ! ! ! --More--   R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run int s 1/0 Building configuration... Current configuration : 209 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay no ip split-horizon eigrp 100 no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 end R3# R3#^x6 % Unknown command or computer name, or unable to find computer address R3# R3# RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#router eigrp 100 S6(config-router)#no auto S6(config-router)#net 17.57.100.2 0.0.0.0 S6(config-router)#exit S6(config)# 04:02:19: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.57.100.1 (Vlan16) is up: new adjacency S6(config)# S6(config)# S6(config)#key S6(config)#key ch S6(config)#key chain ? WORD Key-chain name S6(config)#key chain Prob 3b3   b3 ? S6(config)#key chain Prob3 S6(config-keychain)#? Key-chain configuration commands: default Set a command to its defaults exit Exit from key-chain configuration mode key Configure a key no Negate a command or set its defaults S6(config-keychain)#key ? <0-2147483647> Key identifier S6(config-keychain)#key 1 ? S6(config-keychain)#key 1 S6(config-keychain-key)#ke S6(config-keychain-key)#key-string ? 0 Specifies an UNENCRYPTED password will follow 7 Specifies a HIDDEN password will follow LINE The UNENCRYPTED (cleartext) user password S6(config-keychain-key)#key-string bosco S6(config-keychain-key)#int     do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES manual administratively down down Vlan16 17.57.100.2 YES manual up up FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset down down FastEthernet0/3 unassigned YES unset down down FastEthernet0/4 unassigned YES unset up up FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset down down FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down --More--   S6(config-keychain-key)#int vlan 16 S6(config-if)#ip eigrp > ? % Unrecognized command S6(config-if)#ip eigrp         / ? Interface IP configuration subcommands: access-group Specify access control for packets accounting Enable IP accounting on this interface address Set the IP address of an interface admission Apply Network Admission Control auth-proxy Apply authenticaton proxy authentication authentication subcommands bandwidth-percent Set EIGRP bandwidth limit bgp BGP interface commands broadcast-address Set the broadcast address of an interface cef Cisco Express Forwarding interface commands cgmp Enable/disable CGMP dhcp Configure DHCP parameters for this interface directed-broadcast Enable forwarding of directed broadcasts dvmrp DVMRP interface commands hello-interval Configures IP-EIGRP hello interval helper-address Specify a destination address for UDP broadcasts hold-time Configures IP-EIGRP hold time igmp IGMP interface commands information-reply Enable sending ICMP Information Reply messages irdp ICMP Router Discovery Protocol load-sharing Style of load sharing --More--   S6(config-if)#ip auth S6(config-if)#ip authe S6(config-if)#ip authentication ? key-chain key-chain mode mode S6(config-if)#ip authentication key S6(config-if)#ip authentication key-chain ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) S6(config-if)#ip authentication key-chain ei S6(config-if)#ip authentication key-chain eigrp ? <1-65535> Autonomous system number S6(config-if)#ip authentication key-chain eigrp 1 ? WORD name of key-chain S6(config-if)#ip authentication key-chain eigrp 1  00 ? WORD name of key-chain S6(config-if)#ip authentication key-chain eigrp 100 Prov b3 ? S6(config-if)#ip authentication key-chain eigrp 100 Prob3   S6(config-if)#ip authentication key-chain eigrp 100 Prob3  04:03:49: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.57.100.1 (Vlan16) is down: keychain changed                 ip authentication key-chain eigrp 100 Prob3 04:03:52: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.57.100.1 (Vlan16) is up: new adjacency            ip authentication key-chain eigrp 100 Prob3  S6(config-if)#ip authentication key-chain eigrp 100 Prob3                         mo S6(config-if)#ip authentication mode ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) S6(config-if)#ip authentication mode ei S6(config-if)#ip authentication mode eigrp 100 ? md5 Keyed message digest S6(config-if)#ip authentication mode eigrp 100 md S6(config-if)#ip authentication mode eigrp 100 md5 ? S6(config-if)#ip authentication mode eigrp 100 md5 S6(config-if)# 04:04:16: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.57.100.1 (Vlan16) is down: authentication mode changed^Z S6# RACK9AS>c 1 [Resuming connection 1 to r1 ... ] * R1#cp onfig t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#key ? chain Key-chain management config-key Set a private configuration key R1(config)#key ch R1(config)#key chain ? WORD Key-chain name R1(config)#key chain Prob3 R1(config-keychain)#key R1(config-keychain)#key 1 R1(config-keychain-key)#ke R1(config-keychain-key)#key-string bosco R1(config-keychain-key)#int e 0/1 R1(config-if)#ip authe R1(config-if)#ip authentication mode R1(config-if)#ip authentication mode md R1(config-if)#ip authentication mode md  ei R1(config-if)#ip authentication mode eigrp 100 md R1(config-if)#ip authentication mode eigrp 100 md5 R1(config-if)#ip authen ke R1(config-if)#ip authen key-chain ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) R1(config-if)#ip authen key-chain eigrp 100 ? WORD name of key-chain R1(config-if)#ip authen key-chain eigrp 100 Prob3 ? R1(config-if)#ip authen key-chain eigrp 100 Prob3   R1(config-if)# *Mar 1 04:04:00.831: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.57.100.2 (Ethernet0/1) is up: new adjacency R1(config-if)#^Z R1# *Mar 1 04:04:06.100: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 17.57.100.2 Et0/1 12 00:00:11 1562 5000 0 6 0 208.28.1.2 Se0/0.1 130 00:22:09 631 3786 0 11 R1#sh    deb eigrp pack EIGRP Packets debugging is on (UPDATE, REQUEST, QUERY, REPLY, HELLO, IPXSAP, PROBE, ACK, STUB, SIAQUERY, SIAREPLY) R1# *Mar 1 04:04:30.857: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.2 *Mar 1 04:04:30.857: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1# *Mar 1 04:04:32.603: EIGRP: Sending HELLO on Ethernet0/1 *Mar 1 04:04:32.603: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1# *Mar 1 04:04:33.898: EIGRP: received packet with MD5 authentication, key id = 1 *Mar 1 04:04:33.902: EIGRP: Received HELLO on Ethernet0/1 nbr 17.57.100.2 *Mar 1 04:04:33.902: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/0 R1# *Mar 1 04:04:35.677: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.2 *Mar 1 04:04:35.677: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1# *Mar 1 04:04:37.299: EIGRP: Sending HELLO on Ethernet0/1 *Mar 1 04:04:37.299: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1# *Mar 1 04:04:38.898: EIGRP: received packet with MD5 authentication, key id = 1 *Mar 1 04:04:38.902: EIGRP: Received HELLO on Ethernet0/1 nbr 17.57.100.2 *Mar 1 04:04:38.902: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/0 R1#u al *Mar 1 04:04:40.192: EIGRP: Sending HELLO on Serial0/0.1 nbr 208.28.1.2 *Mar 1 04:04:40.192: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1#u all All possible debugging has been turned off R1# *Mar 1 04:04:42.031: EIGRP: Sending HELLO on Ethernet0/1 *Mar 1 04:04:42.031: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1# R1# R1# R1#sh run | b key key chain Prob3 key 1 key-string bosco ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address --More--   encapsulation frame-relay no fair-queue ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 ip authentication mode eigrp 100 md5 ip authentication key-chain eigrp 100 Prob3 half-duplex ! interface Serial0/1 no ip address shutdown ! router eigrp 100 network 17.57.100.1 0.0.0.0 network 208.28.1.1 0.0.0.0 neighbor 208.28.1.2 Serial0/0.1 distribute-list prefix Prob2 in Serial0/0.1 no auto-summary --More--   R1#^X6 % Unknown command or computer name, or unable to find computer address R1# RACK9AS>6 [Resuming connection 6 to r6 ... ] 04: S6#SH RUN | b key key chain Prob3 key 1 key-string bosco ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport access vlan 16 switchport mode access ! interface FastEthernet0/2 switchport access vlan 20 switchport mode dynamic desirable ! interface FastEthernet0/3 --More--   S6#sh ru int vlan 16 Building configuration... Current configuration : 145 bytes ! interface Vlan16 ip address 17.57.100.2 255.255.255.0 ip authentication mode eigrp 100 md5 ip authentication key-chain eigrp 100 Prob3 end S6# S6#sh run | b reout    outer router eigrp 100 network 17.57.100.2 0.0.0.0 no auto-summary ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 line vty 0 4 no login line vty 5 15 no login ! ! end S6# S6# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router eigrp 100 R4(config-router)#no auto R4(config-router)#net 17.80.1.2 0.0.0.0 R4(config-router)#^Z R4#sh ip rout *Mar 1 04:10:47.858: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 D 17.57.100.0 [90/20540160] via 17.80.1.1, 00:00:00, FastEthernet0/0 208.28.1.0/29 is subnetted, 1 subnets D 208.28.1.0 [90/20514560] via 17.80.1.1, 00:00:00, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.80.1.0 is dir *Mar 1 04:10:50.770: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.1 (FastEthernet0/0) is up: new adjacencyectly connected, FastEthernet0/0 D 17.57.100.0 [90/20540160] via 17.80.1.1, 00:00:02, FastEthernet0/0 208.28.1.0/29 is subnetted, 1 subnets D 208.28.1.0 [90/20514560] via 17.80.1.1, 00:00:02, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 D 17.57.100.0 [90/20540160] via 17.80.1.1, 00:00:02, FastEthernet0/0 208.28.1.0/29 is subnetted, 1 subnets D 208.28.1.0 [90/20514560] via 17.80.1.1, 00:00:02, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 D 17.57.100.0 [90/20540160] via 17.80.1.1, 00:00:03, FastEthernet0/0 208.28.1.0/29 is subnetted, 1 subnets D 208.28.1.0 [90/20514560] via 17.80.1.1, 00:00:03, FastEthernet0/0 R4# R4# R4# R4# R4#sh run | b router eigrp 10 router eigrp 100 network 17.80.1.2 0.0.0.0 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 login ! ! --More--   R4#^x   RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh int s 0/0.1 Serial0/0.1 is up, line protocol is up Hardware is PowerQUICC Serial Internet address is 208.28.1.1/29 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never R1# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh int s 1/0 Serial1/0 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is 208.28.1.2/29 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 1492, LMI stat recvd 1493, LMI upd recvd 0, DTE LMI up LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0 Last input 00:00:01, output 00:00:02, output hang never Last clearing of "show interface" counters 04:08:45 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 2619 packets input, 169356 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 1812 packets output, 41194 bytes, 0 underruns --More--   R3#q  RACK9AS>3 [Resuming connection 3 to r3 ... ] R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#ban 128 R1(config-subif)#^Z R1# *Mar 1 04:11:08.809: %SYS-5-CONFIG_I: Configured from console by console R1#^x3 % Unknown command or computer name, or unable to find computer address R1# R1# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3# R3# R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#ip ba R1(config-subif)#ip bandwidth-percent ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) R1(config-subif)#ip bandwidth-percent ei R1(config-subif)#ip bandwidth-percent eigrp 100 ? <1-999999> Maximum bandwidth percentage that EIGRP may use R1(config-subif)#ip bandwidth-percent eigrp 100 80 ? R1(config-subif)#ip bandwidth-percent eigrp 100 80 R1(config-subif)#^x2 ^ % Invalid input detected at '^' marker. R1(config-subif)# R1(config-subif)# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#int s 1/0.1 R2(config-subif)#ip bandwidth-percent eigrp 100 80 R2(config-subif)#^Z R2# *Mar 1 04:11:13.492: %SYS-5-CONFI RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ip bas R3(config-if)#ip bas\  R3(config-if)#ip bas\  R3(config-if)#ip bas  R3(config-if)#ip bandwidth-percent ei R3(config-if)#ip bandwidth-percent eigrp 100 160 R3(config-if)#^Z R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1(config-subif)#^Z R1#sh run int s *Mar 1 04:14:07.766: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int s 0/0.1 Building configuration... Current configuration : 168 bytes ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 208.28.1.1 255.255.255.248 ip bandwidth-percent eigrp 100 80 frame-relay interface-dlci 103 end R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] G_I: Configured from console by console R2# R2#sh run int s 1/0.1 Building configuration... Current configuration : 184 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 ip bandwidth-percent eigrp 100 80 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 end R2#^x3 % Unknown command or computer name, or unable to find computer address R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run int s 1/0 Building configuration... Current configuration : 245 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 ip bandwidth-percent eigrp 100 160 encapsulation frame-relay no ip split-horizon eigrp 100 no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 end R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ban 256 R3(config-if)#ban 256int s 1/0p bandwidth-percent eigrp 100 160   80 R3(config-if)#^Z R3# R3# R3# R3# *Mar 1 04:14:54.883: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int s 1/0 Building configuration... Current configuration : 259 bytes ! interface Serial1/0 bandwidth 256 ip address 208.28.1.2 255.255.255.248 ip bandwidth-percent eigrp 100 80 encapsulation frame-relay no ip split-horizon eigrp 100 no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 end R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ip sum R3(config-if)#ip summary-address ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) rip Routing Information Protocol (RIP) R3(config-if)#ip summary-address eu i R3(config-if)#ip summary-address eigrp 100 ? A.B.C.D IP address R3(config-if)#ip summary-address eigrp 100 17.64.0.0 ? A.B.C.D IP network mask R3(config-if)#ip summary-address eigrp 100 17.64.0.0 255.192.0.0 ? <1-255> Administrative distance R3(config-if)#ip summary-address eigrp 100 17.64.0.0 255.192.0.0 R3(config-if)# *Mar 1 04:17:44.293: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.3 (Serial1/0) is down: summary configured *Mar 1 04:17:44.293: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.1 (Serial1/0) is down: summary configured R3(config-if)#^Z R3# *Mar 1 04:17:48.311: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.1 (Serial1/0) is up: new adjacency *Mar 1 04:17:49.145: %SYS-5-CONFIG_I: Configured from console by console R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#ip sum   R1(config-subif)#ip summary-address ei R1(config-subif)#ip summary-address eigrp 100 ? A.B.C.D IP address R1(config-subif)#ip summary-address eigrp 100 17.0.0.0 255.2 0.0.0 R1(config-subif)#^Z R1# *Mar 1 04:19:15.194: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se0/0.1 179 00:00:00 1 2000 1 0 1 17.57.100.2 Et0/1 10 00:15:33 408 2448 0 9 R1# *Mar 1 04:19:33.789: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial0/0.1) is up: new adjacency R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se0/0.1 177 00:00:03 934 5000 0 24 1 17.57.100.2 Et0/1 12 00:15:36 326 1956 0 10 R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 3 subnets, 3 masks D 17.0.0.0/8 is a summary, 00:00:06, Null0 C 17.57.100.0/24 is directly connected, Ethernet0/1 D 17.64.0.0/10 [90/20514560] via 208.28.1.2, 00:00:07, Serial0/0.1 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 R1# R1# R1#^x   RACK9AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 3 subnets, 3 masks D 17.0.0.0/8 [90/10537472] via 208.28.1.1, 00:00:27, Serial1/0 C 17.80.1.0/24 is directly connected, FastEthernet0/0 D 17.64.0.0/10 is a summary, 00:01:25, Null0 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0 R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 2 subnets, 2 masks D 17.0.0.0/8 [90/21049600] via 208.28.1.2, 00:00:38, Serial1/0.1 D 17.64.0.0/10 [90/20514560] via 208.28.1.2, 00:00:38, Serial1/0.1 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0.1 R2#ping 17.57.100.1 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/116/124 ms R2#ping 17.57.100.2        80.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R2#^x1    RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.66) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 17.0.0.0/8, 1 successors, FD is 281600, serno 11 via Summary (281600/0), Null0 via 208.28.1.2 (21049600/10537472), Serial0/0.1 P 17.57.100.0/24, 1 successors, FD is 281600, serno 2 via Connected, Ethernet0/1 P 17.64.0.0/10, 1 successors, FD is 20514560, serno 12 via 208.28.1.2 (20514560/28160), Serial0/0.1 P 208.28.1.0/29, 1 successors, FD is 20512000, serno 6 via Connected, Serial0/0.1 R1#sh ip pre ip prefix-list Prob2: 3 entries seq 5 deny 17.57.100.0/24 seq 10 deny 208.28.1.0/29 seq 15 permit 0.0.0.0/0 le 32 R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pre R1(config)#ip prefix-list Prto   rob2 ? deny Specify packets to reject description Prefix-list specific description permit Specify packets to forward seq sequence number of an entry R1(config)#ip prefix-list Prob2 seq 12 ? deny Specify packets to reject permit Specify packets to forward R1(config)#ip prefix-list Prob2 seq 12 den 17.0.0.0/8 R1(config)#^Z R1# *Mar 1 04:22:18.559: %SYS-5-CONFIG_I: Configured from console by console R1#sh *Mar 1 04:22:22.497: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial0/0.1) is down: route configuration changed R1#sh run int s 0/0.1 Building configuration... Current configuration : 219 bytes ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 208.28.1.1 255.255.255.248 ip bandwidth-percent eigrp 100 80 ip summary-address eigrp 100 17.0.0.0 255.0.0.0 5 frame-relay interface-dlci 103 end R1#sg   h run | b ip pre ip prefix-list Prob2 seq 5 deny 17.57.100.0/24 ip prefix-list Prob2 seq 10 deny 208.28.1.0/29 ip prefix-list Prob2 seq 12 deny 17.0.0.0/8 ip prefix-list Prob2 seq 15 permit 0.0.0.0/0 le 32 ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! end R1# R1#^x3 % Unknown command or computer name, or unable to find computer address R1# R1# RACK9AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run int s 1/0 Building configuration... Current configuration : 313 bytes ! interface Serial1/0 bandwidth 256 ip address 208.28.1.2 255.255.255.248 ip bandwidth-percent eigrp 100 80 encapsulation frame-relay no ip split-horizon eigrp 100 ip summary-address eigrp 100 17.64.0.0 255.192.0.0 5 no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 end R3# R3# R3#^x4 % Unknown command or computer name, or unable to find computer address R3# R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#coi nfig t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#itn  nt fa 0/0 R4(config-if)#ip ei R4(config-if)#ip ei? % Unrecognized command R4(config-if)#ip ei  tim R4(config-if)#ip tim? % Unrecognized command R4(config-if)#ip tim   ei? % Unrecognized command R4(config-if)#ip ei  ? Interface IP configuration subcommands: access-group Specify access control for packets accounting Enable IP accounting on this interface address Set the IP address of an interface audit Apply IDS audit name auth-proxy Apply authentication proxy authentication authentication subcommands bandwidth-percent Set EIGRP bandwidth limit bgp BGP interface commands broadcast-address Set the broadcast address of an interface cef Cisco Express Forwarding interface commands cgmp Enable/disable CGMP dhcp Configure DHCP parameters for this interface directed-broadcast Enable forwarding of directed broadcasts dvmrp DVMRP interface commands flow NetFlow related commands hello-interval Configures IP-EIGRP hello interval helper-address Specify a destination address for UDP broadcasts hold-time Configures IP-EIGRP hold time idle-group Specify interesting packets for idle-timer igmp IGMP interface commands information-reply Enable sending ICMP Information Reply messages --More--   R4(config-if)#ip he R4(config-if)#ip hell R4(config-if)#ip hello-interval ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) R4(config-if)#ip hello-interval ei R4(config-if)#ip hello-interval eigrp ? <1-65535> Autonomous system number R4(config-if)#ip hello-interval eigrp 100 ? <1-65535> Seconds between hello transmissions R4(config-if)#ip hello-interval eigrp 100 30 ? R4(config-if)#ip hello-interval eigrp 100 30 R4(config-if)# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.1 Se1/0 12 00:02:44 36 354 0 25 1 208.28.1.3 Se1/0 178 00:06:29 38 354 0 21 2 17.80.1.2 Fa0/0 4 00:16:00 4 200 0 8 R3# *Mar 1 04:24:24.116: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.2 (FastEthernet0/0) is down: holding time expired R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.1 Se1/0 11 00:02:54 36 354 0 25 1 208.28.1.3 Se1/0 168 00:06:39 38 354 0 21 R3# *Mar 1 04:24:38.600: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.2 (FastEthernet0/0) is up: new adjacency R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 2 17.80.1.2 Fa0/0 12 00:00:02 1 3000 1 0 0 208.28.1.1 Se1/0 14 00:03:06 36 354 0 25 1 208.28.1.3 Se1/0 156 00:06:51 38 354 0 21 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s   *Mar 1 04:24:57.976: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.2 (FastEthernet0/0) is down: holding time expired R3(config)#int s fa 0/0 R3(config-if)#ip *Mar 1 04:25:04.819: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.2 (FastEthernet0/0) is up: new adjacency R3(config-if)#ip hold eigrp 100 90 ? R3(config-if)#ip hold eigrp 100 90 R3(config-if)#^Z R3#config tsh ip eigrp nei *Mar 1 04:25:19.675: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 2 17.80.1.2 Fa0/0 0 00:00:17 1 3000 0 12 0 208.28.1.1 Se1/0 11 00:03:47 36 354 0 25 1 208.28.1.3 Se1/0 172 00:07:31 38 354 0 21 R3# *Mar 1 04:25:22.540: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.2 (FastEthernet0/0) is down: holding time expired R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 2 17.80.1.2 Fa0/0 13 00:00:01 1 2000 1 0 0 208.28.1.1 Se1/0 12 00:03:59 36 354 0 25 1 208.28.1.3 Se1/0 159 00:07:44 38 354 0 21 R3# *Mar 1 04:25:33.350: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.2 (FastEthernet0/0) is up: new adjacency R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 2 17.80.1.2 Fa0/0 13 00:00:04 1 3000 0 14 0 208.28.1.1 Se1/0 13 00:04:03 36 354 0 25 1 208.28.1.3 Se1/0 155 00:07:47 38 354 0 21 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int *Mar 1 04:25:51.367: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.2 (FastEthernet0/0) is down: holding time expired R3(config)#int fa 0/0 R3(config-if)#int fa 0/0p hold eigrp 100 90 nip hold eigrp 100 90 oip hold eigrp 100 90  ip hold eigrp 100 90  RACK9AS>4 [Resuming connection 4 to r4 ... ] *Ma R4(config-if)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 17.80.1.1 Fa0/0 89 00:00:09 1 5000 1 34 R4(config-if)# *Mar 1 04:28:47.898: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.1 (FastEthernet0/0) is down: Interface Goodbye received R4(config-if)# RACK9AS>3 [Resuming connection 3 to r3 ... ] *M R3(config-if)#no ip hold eigrp 100 90  no ip hold eigrp 100 90 R3(config-if)#^Z R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] *Ma R4(config-if)#ip hold eigrp 100 90 R4(config-if)#^Z R4#^x3 % Unknown command or computer name, or unable to find computer address R4# R4# *Mar 1 04:29:09.286: %SYS-5-CONFIG_I: Configured from console by console R4# RACK9AS>3 [Resuming connection 3 to r3 ... ] *M R3#config tsh ip eigrp nei *Mar 1 04:26:44.991: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.2 (FastEthernet0/0) is down: holding time expired R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.1 Se1/0 13 00:05:12 36 354 0 25 1 208.28.1.3 Se1/0 146 00:08:56 38 354 0 21 R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.1 Se1/0 10 00:05:15 36 354 0 25 1 208.28.1.3 Se1/0 142 00:09:00 38 354 0 21 R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.1 Se1/0 13 00:05:17 36 354 0 25 1 208.28.1.3 Se1/0 140 00:09:02 38 354 0 21 R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.1 Se1/0 11 00:05:19 36 354 0 25 1 208.28.1.3 Se1/0 139 00:09:03 38 354 0 21 R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.1 Se1/0 14 00:05:20 36 354 0 25 1 208.28.1.3 Se1/0 137 00:09:05 38 354 0 21 R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.1 Se1/0 12 00:05:22 36 354 0 25 1 208.28.1.3 Se1/0 136 00:09:06 38 354 0 21 R3#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 2 17.80.1.2 Fa0/0 89 00:00:00 1 2000 1 0 0 208.28.1.1 Se1/0 11 00:05:23 36 354 0 25 1 208.28.1.3 Se1/0 134 00:09:08 38 354 0 21 R3# *Mar 1 04:26:57.796: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 17.80.1.2 (FastEthernet0/0) is up: new adjacency R3# R3# R3# R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#sh run int fa 0/0 Building configuration... Current configuration : 153 bytes ! interface FastEthernet0/0 ip address 17.80.1.2 255.255.255.0 ip hello-interval eigrp 100 30 ip hold-time eigrp 100 90 duplex auto speed auto end R4# R4# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eigrp 100 R2(config-router)#st R2(config-router)#st? % Unrecognized command R2(config-router)#st  ? Router configuration commands: address-family Enter Address Family command mode auto-summary Enable automatic network number summarization default Set a command to its defaults default-information Control distribution of default information default-metric Set metric of redistributed routes distance Define an administrative distance distribute-list Filter networks in routing updates eigrp EIGRP specific commands exit Exit from routing protocol configuration mode help Description of the interactive help system maximum-paths Forward packets over multiple paths metric Modify EIGRP routing metrics and parameters neighbor Specify a neighbor router network Enable routing on an IP network no Negate a command or set its defaults offset-list Add or subtract offset from RIP metrics passive-interface Suppress routing updates on an interface redistribute Redistribute information from another routing protocol timers Adjust routing timers traffic-share How to compute traffic share over alternate paths variance Control load balancing variance --More--   R2(config-router)#i R2(config-router)#i eu i R2(config-router)#eigrp ? log-neighbor-changes Enable/Disable IP-EIGRP neighbor logging log-neighbor-warnings Enable/Disable IP-EIGRP neighbor warnings router-id router-id for this EIGRP process stub Set IP-EIGRP as stubbed router R2(config-router)#eigrp stu R2(config-router)#eigrp stub ? connected Do advertise connected routes receive-only Set IP-EIGRP as receive only neighbor redistributed Do advertise redistributed routes static Do advertise static routes summary Do advertise summary routes R2(config-router)#eigrp stub re R2(config-router)#eigrp stub rec R2(config-router)#eigrp stub receive-only R2(config-router)# *Mar 1 04:30:47.589: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial1/0.1) is down: peer info changed R2(config-router)# *Mar 1 04:31:26.765: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial1/0.1) is up: new adjacency R2(config-router)#^Z R2#sh *Mar 1 04:32:22.845: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.2 Se1/0.1 172 00:01:01 44 708 0 37 R2#sh run | b router router eigrp 100 network 208.28.1.3 0.0.0.0 neighbor 208.28.1.2 Serial1/0.1 distribute-list prefix Prob2 in Serial1/0.1 no auto-summary eigrp stub receive-only ! ip classless ! no ip http server no ip http secure-server ! ! ip prefix-list Prob2 seq 5 deny 208.28.1.0/29 ip prefix-list Prob2 seq 10 permit 0.0.0.0/0 le 32 access-list 100 deny ip host 208.28.1.0 host 255.255.255.248 access-list 100 permit ip any any ! ! ! ! ! ! --More--   R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 3 subnets, 3 masks D 17.0.0.0/8 is a summary, 00:14:39, Null0 C 17.57.100.0/24 is directly connected, Ethernet0/1 D 17.64.0.0/10 [90/20514560] via 208.28.1.2, 00:10:58, Serial0/0.1 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int     route    jasdfhaufhdapifgaiudiaugiduhhhhhhhhhhhhhhhhhhhhhh                                                  int s 0/0.1 R1(config-subif)#int s 0/0.1p prefix-list Prob2 seq 12 den 17.0.0.0/8summary-address eigrp 100 17.0.0.0 255.0.0.0nt s 0/0.1 p summary-address eigrp 100 17.0.0.0 255.0.0.0 ? <1-255> Administrative distance R1(config-subif)#ip summary-address eigrp 100 17.0.0.0 255.0.0.0 255 R1(config-subif)# *Mar 1 04:38:36.955: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial0/0.1) is down: summary configured R1(config-subif)# *Mar 1 04:38:48.866: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.2 (Serial0/0.1) is up: new adjacency R1(config-subif)#^Z R1#sh *Mar 1 04:39:19.040: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 3 subnets, 3 masks D 17.0.0.0/8 is a summary, 00:19:46, Null0 C 17.57.100.0/24 is directly connected, Ethernet0/1 D 17.64.0.0/10 [90/20514560] via 208.28.1.2, 00:00:30, Serial0/0.1 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 R1#clea ip routr   e * R1#clea ip route *sh ip route  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 2 subnets, 2 masks C 17.57.100.0/24 is directly connected, Ethernet0/1 D 17.64.0.0/10 [90/20514560] via 208.28.1.2, 00:00:01, Serial0/0.1 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 R1# R1# R1# R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 2 subnets, 2 masks C 17.57.100.0/24 is directly connected, Ethernet0/1 D 17.64.0.0/10 [90/20514560] via 208.28.1.2, 00:00:06, Serial0/0.1 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 2 subnets, 2 masks D 17.0.0.0/8 [90/21049600] via 208.28.1.2, 00:00:57, Serial1/0.1 D 17.64.0.0/10 [90/20514560] via 208.28.1.2, 00:07:06, Serial1/0.1 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0.1 R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip eigrp tyop a     op IP-EIGRP Topology Table for AS(100)/ID(208.28.1.66) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 17.0.0.0/8, 1 successors, FD is 281600 via Summary (281600/0), Null0 P 17.57.100.0/24, 1 successors, FD is 281600 via Connected, Ethernet0/1 P 17.64.0.0/10, 1 successors, FD is 20514560 via 208.28.1.2 (20514560/28160), Serial0/0.1 P 208.28.1.0/29, 1 successors, FD is 20512000 via Connected, Serial0/0.1 R1# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 R3#ci =o  onfig t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#int s 1/0no ip hold eigrp 100 90 int fa 0/0 p hold eigrp 100 90 nt fa 0/0 p summary-address eigrp 100 17.64.0.0 255.192.0.0 255 R3(config-if)#^Z R3# *Mar 1 04:40:18.489: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.1 (Serial1/0) is down: summary configured *Mar 1 04:40:18.489: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.3 (Serial1/0) is down: summary configured R3# *Mar 1 04:40:20.224: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 04:40:22.608: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.1 (Serial1/0) is up: new adjacency R3#config t sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 2 subnets, 2 masks C 17.80.1.0/24 is directly connected, FastEthernet0/0 D 17.64.0.0/10 is a summary, 00:22:56, Null0 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0 R3#sh    clea ip route * R3#clea ip route *sh ip route  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0 R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0 R3# *Mar 1 04:40:58.562: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.3 (Serial1/0) is up: new adjacency R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/8 is variably subnetted, 2 subnets, 2 masks D 17.0.0.0/8 [90/10537472] via 208.28.1.1, 00:00:00, Serial1/0 C 17.80.1.0/24 is directly connected, FastEthernet0/0 208.28.1.0/29 is subnetted, 1 subnets C 208.28.1.0 is directly connected, Serial1/0 R3#^x1 % Unknown command or computer name, or unable to find computer address R3# R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh run int fa  e   s 0/0.1 Building configuration... Current configuration : 221 bytes ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 208.28.1.1 255.255.255.248 ip bandwidth-percent eigrp 100 80 ip summary-address eigrp 100 17.0.0.0 255.0.0.0 255 frame-relay interface-dlci 103 end R1# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/0 Building configuration... Current configuration : 315 bytes ! interface Serial1/0 bandwidth 256 ip address 208.28.1.2 255.255.255.248 ip bandwidth-percent eigrp 100 80 encapsulation frame-relay no ip split-horizon eigrp 100 ip summary-address eigrp 100 17.64.0.0 255.192.0.0 255 no fair-queue frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 end R3# R3#