=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.10.19 14:15:03 =~=~=~=~=~=~=~=~=~=~=~= config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#do sh ip ala sh ip ala ^ % Invalid input detected at '^' marker. S6(config)#do sh ip ala i Address Type IP Address Port Interface 60.1.1.1 Interface 17.57.101.1 Interface 17.57.100.2 Interface 17.57.103.1 Interface 17.57.102.1 S6(config)#sh ip     do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES manual administratively down down FastEthernet0/1 17.57.100.2 YES manual up up FastEthernet0/2 unassigned YES unset up up FastEthernet0/3 unassigned YES unset down down FastEthernet0/4 unassigned YES unset up up FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset down down FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down FastEthernet0/21 unassigned YES unset down down --More--  FastEthernet0/22 unassigned YES unset up up FastEthernet0/23 unassigned YES unset down down FastEthernet0/24 unassigned YES unset up up GigabitEthernet0/1 unassigned YES unset down down GigabitEthernet0/2 unassigned YES unset down down Loopback0 17.57.101.1 YES manual up up Loopback1 17.57.102.1 YES manual up up Loopback2 17.57.103.1 YES manual up up Loopback99 60.1.1.1 YES manual up up S6(config)#int lo 3 S6(config-if)#ip add 6 03:15:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback3, changed state to up.6.6.6. 6 .6 255.255.255.255.  ^ % Invalid input detected at '^' marker. S6(config-if)#ip add 6.6.6.6.6 255.255.255.255 ^ % Invalid input detected at '^' marker. S6(config-if)#ip add 6.6.6.6.6 255.255.255.2556 255.255.255.255  255.255.255.255  S6(config-if)#^Z S6# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip int brier ^ % Invalid input detected at '^' marker. S5#sh ip int brier  Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES manual administratively down down Vlan10 208.28.1.65 YES manual up up Vlan20 208.28.1.130 YES manual up up FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down --More--  FastEthernet0/20 unassigned YES unset down down FastEthernet0/21 unassigned YES unset down down FastEthernet0/22 unassigned YES unset up up FastEthernet0/23 unassigned YES unset up up FastEthernet0/24 unassigned YES unset up up GigabitEthernet0/1 unassigned YES unset down down GigabitEthernet0/2 unassigned YES unset down down Loopback99 50.1.1.1 YES manual up up S5#confi gt ^ % Invalid input detected at '^' marker. S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int lo 0~  S5(config-if)#ip addres 03:16:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up S5(config-if)#ip addres 5.5.5.5 255.2355.    55.255.255.  S5(config-if)#^Z S5# RACK99AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Serial0/0.2 180.40.7.66 YES manual up up Ethernet0/1 17.57.100.1 YES manual up up Serial0/1 180.40.7.130 YES manual up up Loopback99 10.1.1.1 YES manual up up R1(config)# in tlo 0 ^ % Invalid input detected at '^' marker. R1(config)#in tlo 0lo 0 t lo 0 R1(config-if)#ip add 1.1.1.1 255.255.255.255 R1(config-if)#^Z R1# RACK99AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#in tlo 0lo 0 lo 0 tlo 0 lo 0 R2(config-if)#do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES manual administratively down down BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 208.28.1.129 YES manual up up Serial1/0 180.40.7.65 YES manual up up Serial1/1 180.40.7.129 YES manual up up Serial1/2 180.40.7.2 YES manual up up Serial1/3 unassigned YES manual administratively down down Serial1/4 unassigned YES manual administratively down down Serial1/5 unassigned YES manual administratively down down --More--   R2(config-if)#p adddo sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES manual administratively down down BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 208.28.1.129 YES manual up up Serial1/0 180.40.7.65 YES manual up up Serial1/1 180.40.7.129 YES manual up up Serial1/2 180.40.7.2 YES manual up up Serial1/3 unassigned YES manual administratively down down Serial1/4 unassigned YES manual administratively down down Serial1/5 unassigned YES manual administratively down down --More--  Serial1/6 unassigned YES manual administratively down down Serial1/7 unassigned YES manual administratively down down Loopback0 unassigned YES unset up up Loopback99 20.1.1.1 YES manual up up R2(config-if)# ip add 2.2.2.2 255.255.255.255 R2(config-if)#^Z R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#in tlo 0lo 0 lo 0 tlo 0 lo 0 R3(config-if)#ip add 3.3.3.3 255.255.255.255 R3(config-if)#^Z R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4# R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo 0 R4(config-if)#ip add 4.4.4.4 255.5 255.255.255 R4(config-if)#^Z R4# 03:16:44: %SYS-5-CONFIG_I: Configured from console by console R4# RACK99AS>6 [Resuming connection 6 to r6 ... ] 03:16:02: %SYS-5-CONFIG_I: Config S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#rotuer      uter bgp 300 S6(config-router)#no auto S6(config-router)#bgp rout S6(config-router)#bgp router-id 0.0.0.6 %Invalid router-id 0.0.0.6 S6(config-router)#bgp router-id 0.0.0.6       6.6.6.6   S6(config-router)#net 60.0.0.0 S6(config-router)#net 6.6.6.6 mask 255.255.255.255 S6(config-router)#net 17.57.101.0 mask 255.255.255.0 S6(config-router)#net 17.57.101.0 mask 255.255.255.0\.0 mask 255.255.255.0.0 mask 255.255.255.0 .0 mask 255.255.255.0 2.0 mask 255.255.255.0 S6(config-router)#net 17.57.102.0 mask 255.255.255.0.0 mask 255.255.255.0 3.0 mask 255.255.255.0 S6(config-router)#net 17.57.103.0 mask 255.255.255.0.0 mask 255.255.255.0 0.0 mask 255.255.255.0 S6(config-router)#do sh ip proto *** IP Routing is NSF aware *** Routing Protocol is "bgp 300" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set IGP synchronization is disabled Automatic route summarization is disabled Maximum path: 1 Routing Information Sources: Gateway Distance Last Update Distance: external 20 internal 200 local 200 S6(config-router)#nei 17.57.100.1 remote 300 S6(config-router)#^Z S6# 03:23:44: %SYS-5-CONFIG_I: Configured from console by console RACK99AS>1 [Resuming connection 1 to r1 ... ] *M R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router bgp 300 R1(config-router)#no auto R1(config-router)#bgp route 1.1.1.1 R1(config-router)#net 10.0.0.0 R1(config-router)#net 1.1.1.1 mask 255.255.255.255 R1(config-router)#net 208.28.1.64 mask 255.255.255.240 R1(config-router)#net 180.40.7.128 mask 255.255.255.224 R1(config-router)#net 180.40.7.128 mask 255.255.255.224 mask 255.255.255.224  mask 255.255.255.224  mask 255.255.255.224 6 mask 255.255.255.2244 mask 255.255.255.224 R1(config-router)#net 180.40.7.64 mask 255.255.255.224128 mask 255.255.255.224208.28.1.64 mask 255.255.255.240  84 mask 255.255.255.248  mask 255.255.255.248 0 mask 255.255.255.248 R1(config-router)#nei 208.28.1.65 remote 200 R1(config-router)#nei 180.40.7.129 remote 100 R1(config-router)#nei 180.40.7.129 remote 100 remote 100  remote 100  remote 100 6 remote 1005 remote 100 R1(config-router)#nei 208.28.1.2 remote 100 R1(config-router)#nei 17.57.100.2 remote 300 R1(config-router)#^Z R1# RACK99AS>5 [Resuming connection 5 to r5 ... ] 03: S5#confi gt ^ % Invalid input detected at '^' marker. S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#do sh int vlan 10 Vlan10 is up, line protocol is up Hardware is EtherSVI, address is 0012.7f57.9480 (bia 0012.7f57.9480) Internet address is 208.28.1.65/29 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 3 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts (0 IP multicast) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 interface resets 0 output buffer failures, 0 output buffers swapped out S5(config)#int vlan 10 S5(config-if)#ip add 208.28.1.65/29    255.255.255.240 S5(config-if)#router bgp 200 S5(config-router)#no auto S5(config-router)#bgp rout S5(config-router)#bgp router-id 5.5.5.5 S5(config-router)#net 50.0.0.0 S5(config-router)#net 5.5.5.5 mask 255.255.255.255.  S5(config-router)#net 208.28.1.128 mask 255.255.255.224 S5(config-router)#nei 208.28.1.66 remote 300 S5(config-router)#nei 208.28.1.66 remote 30000 100 remote 100  remote 100 1 remote 1002 remote 1009 remote 100 S5(config-router)#^Z S5# RACK99AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router bgp 100 R2(config-router)#no auto R2(config-router)#bgp rout 2.2.2.2 R2(config-router)#net 20.0.0.0 R2(config-router)#net 2.2.2.2 mask 255.255.255.255 R2(config-router)#net 180.40.7.0 mask 255.255.255.224 R2(config-router)#nei 203 8/.  .28.1.130 ro emote 200 R2(config-router)#nei 180.40.7.130 remote 300 R2(config-router)#nei 180.40.7.130 remote 300 remote 300  remote 300  remote 300 6 remote 3006 remote 300 R2(config-router)#remote        nei 180.40.7.3 rwmo    remote 100 R2(config-router)#^Z R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] *M R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router bgp 100 R3(config-router)#no auto R3(config-router)#bgp route 3.3.3.3 R3(config-router)#net 30.0.0.0 R3(config-router)#net 3.3.3.3 maskl    255.255.255.255 R3(config-router)#nei 180.40.7.2 remote 100 R3(config-router)#net i 17.80.1.2 remote 100 R3(config-router)#nei 208.28.1.1 remote 300 R3(config-router)#^Z R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router bgp 10p0  0 R4(config-router)#no auto R4(config-router)#bgp rotue 4.4.4.4 ^ % Invalid input detected at '^' marker. R4(config-router)#bgp rotue 4.4.4.4e 4.4.4.4 e 4.4.4.4 ue 4.4.4.4te 4.4.4.4 R4(config-router)#net 40.0.0.0 R4(config-router)#net 4.4.4.4 mask 255.255.255.255 R4(config-router)#net 17.80.1.0 mask 255.25. 5.255.0 R4(config-router)#nei 17.80.1.1 remote 100 R4(config-router)#^Z R4# 03:30:49: %SYS-5-CONFIG_I: Configured from console by console R4# RACK99AS>6 [Resuming connection 6 to r6 ... ] 03 S6#sh ip bgp sum BGP router identifier 6.6.6.6, local AS number 300 BGP table version is 22, main routing table version 22 18 network entries using 2034 bytes of memory 18 path entries using 936 bytes of memory 5/4 BGP path/bestpath attribute entries using 540 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 3558 total bytes of memory BGP activity 18/0 prefixes, 18/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 17.57.100.1 4 300 13 10 22 0 0 00:05:50 12 S6#sh ip bgp sum    BGP table version is 29, local router ID is 6.6.6.6 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *>i1.1.1.1/32 17.57.100.1 0 100 0 i *>i2.2.2.2/32 180.40.7.65 0 100 0 100 i *>i3.3.3.3/32 208.28.1.2 0 100 0 100 i *>i4.4.4.4/32 208.28.1.2 0 100 0 100 i *>i5.5.5.5/32 208.28.1.65 0 100 0 200 i *> 6.6.6.6/32 0.0.0.0 0 32768 i *>i10.0.0.0 17.57.100.1 0 100 0 i *> 17.57.100.0/24 0.0.0.0 0 32768 i *> 17.57.101.0/24 0.0.0.0 0 32768 i *> 17.57.102.0/24 0.0.0.0 0 32768 i *> 17.57.103.0/24 0.0.0.0 0 32768 i *>i17.80.1.0/24 208.28.1.2 0 100 0 100 i *>i20.0.0.0 180.40.7.65 0 100 0 100 i *>i30.0.0.0 208.28.1.2 0 100 0 100 i *>i40.0.0.0 208.28.1.2 0 100 0 100 i *>i50.0.0.0 208.28.1.65 0 100 0 200 i *> 60.0.0.0 0.0.0.0 0 32768 i --More--   Network Next Hop Metric LocPrf Weight Path *>i180.40.7.0/27 180.40.7.65 0 100 0 100 i *>i180.40.7.64/27 17.57.100.1 0 100 0 i *>i180.40.7.128/27 17.57.100.1 0 100 0 i *>i208.28.1.0/29 17.57.100.1 0 100 0 i *>i208.28.1.64/28 17.57.100.1 0 100 0 i *>i208.28.1.128/27 208.28.1.65 0 100 0 200 i S6# RACK99AS>4 [Resuming connection 4 to r4 ... ] 03 R4#sh ip bgp BGP table version is 6, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i1.1.1.1/32 208.28.1.1 0 100 0 300 i *>i3.3.3.3/32 17.80.1.1 0 100 0 i *> 4.4.4.4/32 0.0.0.0 0 32768 i * i5.5.5.5/32 208.28.1.1 0 100 0 300 200 i * i6.6.6.6/32 208.28.1.1 0 100 0 300 i * i10.0.0.0 208.28.1.1 0 100 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i *> 17.80.1.0/24 0.0.0.0 0 32768 i *>i30.0.0.0 17.80.1.1 0 100 0 i *> 40.0.0.0 0.0.0.0 0 32768 i * i50.0.0.0 208.28.1.1 0 100 0 300 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i * i180.40.7.64/27 208.28.1.1 0 100 0 300 i * i180.40.7.128/27 208.28.1.1 0 100 0 300 i --More--   R4# RACK99AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 5 subnets B 17.80.1.0 [200/0] via 208.28.1.2, 00:00:28 C 17.57.100.0 is directly connected, FastEthernet0/1 C 17.57.101.0 is directly connected, Loopback0 C 17.57.102.0 is directly connected, Loopback1 C 17.57.103.0 is directly connected, Loopback2 1.0.0.0/32 is subnetted, 1 subnets B 1.1.1.1 [200/0] via 17.57.100.1, 00:06:47 B 50.0.0.0/8 [200/0] via 208.28.1.65, 00:02:58 2.0.0.0/32 is subnetted, 1 subnets B 2.2.2.2 [200/0] via 180.40.7.65, 00:02:43 3.0.0.0/32 is subnetted, 1 subnets B 3.3.3.3 [200/0] via 208.28.1.2, 00:00:51 --More--   4.0.0.0/32 is subnetted, 1 subnets B 4.4.4.4 [200/0] via 208.28.1.2, 00:00:30 B 20.0.0.0/8 [200/0] via 180.40.7.65, 00:02:44 5.0.0.0/32 is subnetted, 1 subnets B 5.5.5.5 [200/0] via 208.28.1.65, 00:03:01 6.0.0.0/32 is subnetted, 1 subnets C 6.6.6.6 is directly connected, Loopback3 B 40.0.0.0/8 [200/0] via 208.28.1.2, 00:00:30 B 10.0.0.0/8 [200/0] via 17.57.100.1, 00:06:49 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks B 208.28.1.128/27 [200/0] via 208.28.1.65, 00:03:01 B 208.28.1.64/28 [200/0] via 17.57.100.1, 00:06:50 B 208.28.1.0/29 [200/0] via 17.57.100.1, 00:06:50 180.40.0.0/27 is subnetted, 3 subnets B 180.40.7.128 [200/0] via 17.57.100.1, 00:06:50 B 180.40.7.0 [200/0] via 180.40.7.65, 00:02:45 B 180.40.7.64 [200/0] via 17.57.100.1, 00:06:50 C 60.0.0.0/8 is directly connected, Loopback99 B 30.0.0.0/8 [200/0] via 208.28.1.2, 00:00:53 S6#sh ip route sum IP routing table name is Default-IP-Routing-Table(0) IP routing table maximum-paths is 32 Route Source Networks Subnets Overhead Memory (bytes) connected 1 5 384 912 static 0 0 0 0 bgp 300 5 12 1088 2584 External: 0 Internal: 17 Local: 0 internal 9 10548 Total 15 17 1472 14044 S6# RACK99AS>1 [Resuming connection 1 to r1 ... ] * R1#sh ip bgp sum BGP router identifier 1.1.1.1, local AS number 300 BGP table version is 30, main routing table version 30 23 network entries using 2323 bytes of memory 47 path entries using 2256 bytes of memory 7 BGP path attribute entries using 420 bytes of memory 4 BGP AS-PATH entries using 96 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 5095 total bytes of memory BGP activity 23/0 prefixes, 47/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 17.57.100.2 4 300 12 18 30 0 0 00:07:08 6 180.40.7.65 4 100 13 14 30 0 0 00:03:04 8 180.40.7.129 4 100 13 13 30 0 0 00:03:13 8 208.28.1.2 4 100 9 9 30 0 0 00:01:46 11 208.28.1.65 4 200 14 13 30 0 0 00:04:53 8 R1# R1# R1# R1#sh ip bgp BGP table version is 30, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 1.1.1.1/32 0.0.0.0 0 32768 i * 2.2.2.2/32 208.28.1.2 0 100 i * 208.28.1.65 0 200 100 i *> 180.40.7.65 0 0 100 i * 180.40.7.129 0 0 100 i * 3.3.3.3/32 180.40.7.65 0 100 i * 180.40.7.129 0 100 i *> 208.28.1.2 0 0 100 i * 208.28.1.65 0 200 100 i *> 4.4.4.4/32 208.28.1.2 0 100 i * 5.5.5.5/32 208.28.1.2 0 100 200 i * 180.40.7.65 0 100 200 i * 180.40.7.129 0 100 200 i *> 208.28.1.65 0 0 200 i *>i6.6.6.6/32 17.57.100.2 0 100 0 i *> 10.0.0.0 0.0.0.0 0 32768 i r>i17.57.100.0/24 17.57.100.2 0 100 0 i --More--   Network Next Hop Metric LocPrf Weight Path *>i17.57.101.0/24 17.57.100.2 0 100 0 i *>i17.57.102.0/24 17.57.100.2 0 100 0 i *>i17.57.103.0/24 17.57.100.2 0 100 0 i *> 17.80.1.0/24 208.28.1.2 0 100 i * 20.0.0.0 208.28.1.2 0 100 i * 208.28.1.65 0 200 100 i *> 180.40.7.65 0 0 100 i * 180.40.7.129 0 0 100 i * 30.0.0.0 180.40.7.65 0 100 i * 180.40.7.129 0 100 i *> 208.28.1.2 0 0 100 i * 208.28.1.65 0 200 100 i *> 40.0.0.0 208.28.1.2 0 100 i * 50.0.0.0 208.28.1.2 0 100 200 i * 180.40.7.65 0 100 200 i * 180.40.7.129 0 100 200 i *> 208.28.1.65 0 0 200 i *>i60.0.0.0 17.57.100.2 0 100 0 i * 180.40.7.0/27 208.28.1.2 0 100 i * 208.28.1.65 0 200 100 i *> 180.40.7.65 0 0 100 i * 180.40.7.129 0 0 100 i --More--   R1# RACK99AS>5 [Resuming connection 5 to r5 ... ] 03:28:0 S5#sh ip bgp sum BGP router identifier 5.5.5.5, local AS number 200 BGP table version is 25, main routing table version 25 23 network entries using 2599 bytes of memory 40 path entries using 2080 bytes of memory 8/6 BGP path/bestpath attribute entries using 864 bytes of memory 4 BGP AS-PATH entries using 96 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 5639 total bytes of memory BGP activity 23/0 prefixes, 40/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 208.28.1.66 4 300 14 15 25 0 0 00:05:46 20 208.28.1.129 4 100 12 14 25 0 0 00:04:12 17 S5#sh ip bgp BGP table version is 25, local router ID is 5.5.5.5 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 1.1.1.1/32 208.28.1.129 0 100 300 i *> 208.28.1.66 0 0 300 i * 2.2.2.2/32 208.28.1.66 0 300 100 i *> 208.28.1.129 0 0 100 i * 3.3.3.3/32 208.28.1.66 0 300 100 i *> 208.28.1.129 0 100 i *> 4.4.4.4/32 208.28.1.66 0 300 100 i *> 5.5.5.5/32 0.0.0.0 0 32768 i * 6.6.6.6/32 208.28.1.129 0 100 300 i *> 208.28.1.66 0 300 i * 10.0.0.0 208.28.1.129 0 100 300 i *> 208.28.1.66 0 0 300 i * 17.57.100.0/24 208.28.1.129 0 100 300 i *> 208.28.1.66 0 300 i * 17.57.101.0/24 208.28.1.129 0 100 300 i *> 208.28.1.66 0 300 i * 17.57.102.0/24 208.28.1.129 0 100 300 i --More--   Network Next Hop Metric LocPrf Weight Path *> 208.28.1.66 0 300 i * 17.57.103.0/24 208.28.1.129 0 100 300 i *> 208.28.1.66 0 300 i *> 17.80.1.0/24 208.28.1.66 0 300 100 i * 20.0.0.0 208.28.1.66 0 300 100 i *> 208.28.1.129 0 0 100 i * 30.0.0.0 208.28.1.66 0 300 100 i *> 208.28.1.129 0 100 i *> 40.0.0.0 208.28.1.66 0 300 100 i *> 50.0.0.0 0.0.0.0 0 32768 i * 60.0.0.0 208.28.1.129 0 100 300 i *> 208.28.1.66 0 300 i * 180.40.7.0/27 208.28.1.66 0 300 100 i *> 208.28.1.129 0 0 100 i * 180.40.7.64/27 208.28.1.129 0 100 300 i *> 208.28.1.66 0 0 300 i * 180.40.7.128/27 208.28.1.129 0 100 300 i *> 208.28.1.66 0 0 300 i * 208.28.1.0/29 208.28.1.129 0 100 300 i *> 208.28.1.66 0 0 300 i r 208.28.1.64/28 208.28.1.129 0 100 300 i r> 208.28.1.66 0 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path *> 208.28.1.128/27 0.0.0.0 0 32768 i S5# RACK99AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh ip bgp sum BGP router identifier 2.2.2.2, local AS number 100 BGP table version is 48, main routing table version 48 20 network entries using 2020 bytes of memory 62 path entries using 2976 bytes of memory 8 BGP path attribute entries using 480 bytes of memory 4 BGP AS-PATH entries using 96 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 5572 total bytes of memory BGP activity 20/0 prefixes, 68/6 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 180.40.7.3 4 100 15 12 48 0 0 00:04:13 14 180.40.7.66 4 300 15 14 48 0 0 00:04:56 15 180.40.7.130 4 300 15 15 48 0 0 00:05:06 15 208.28.1.130 4 200 15 13 48 0 0 00:05:13 15 R2# R2# R2# R2#sh ip bgp BGP table version is 48, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i1.1.1.1/32 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i *> 2.2.2.2/32 0.0.0.0 0 32768 i *>i3.3.3.3/32 180.40.7.3 0 100 0 i * 5.5.5.5/32 180.40.7.66 0 300 200 i * 180.40.7.130 0 300 200 i *> 208.28.1.130 0 0 200 i * i6.6.6.6/32 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i10.0.0.0 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i --More--   Network Next Hop Metric LocPrf Weight Path * i17.57.100.0/24 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i *> 20.0.0.0 0.0.0.0 0 32768 i *>i30.0.0.0 180.40.7.3 0 100 0 i * 50.0.0.0 180.40.7.66 0 300 200 i * 180.40.7.130 0 300 200 i *> 208.28.1.130 0 0 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.0/27 0.0.0.0 0 32768 i r i180.40.7.64/27 208.28.1.1 0 100 0 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r 208.28.1.130 0 200 300 i r i180.40.7.128/27 208.28.1.1 0 100 0 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r 208.28.1.130 0 200 300 i * i208.28.1.0/29 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i * i208.28.1.64/28 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i r 208.28.1.128/27 180.40.7.66 0 300 200 i r 180.40.7.130 0 300 200 i --More--   Network Next Hop Metric LocPrf Weight Path r> 208.28.1.130 0 0 200 i R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh ip bgpo    sum BGP router identifier 3.3.3.3, local AS number 100 BGP table version is 39, main routing table version 39 23 network entries using 2323 bytes of memory 38 path entries using 1824 bytes of memory 7 BGP path attribute entries using 420 bytes of memory 3 BGP AS-PATH entries using 72 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 4639 total bytes of memory BGP activity 23/0 prefixes, 38/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 17.80.1.2 4 100 9 16 39 0 0 00:04:32 3 180.40.7.2 4 100 13 17 39 0 0 00:05:36 18 208.28.1.1 4 300 13 16 39 0 0 00:05:02 15 R3#sh ip bgp BGP table version is 39, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 1.1.1.1/32 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *>i2.2.2.2/32 180.40.7.2 0 100 0 i *> 3.3.3.3/32 0.0.0.0 0 32768 i *>i4.4.4.4/32 17.80.1.2 0 100 0 i *> 5.5.5.5/32 208.28.1.1 0 300 200 i * i 208.28.1.130 0 100 0 200 i *> 6.6.6.6/32 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i *> 10.0.0.0 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.100.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.101.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.102.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path *> 17.57.103.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i r>i17.80.1.0/24 17.80.1.2 0 100 0 i *>i20.0.0.0 180.40.7.2 0 100 0 i *> 30.0.0.0 0.0.0.0 0 32768 i *>i40.0.0.0 17.80.1.2 0 100 0 i *> 50.0.0.0 208.28.1.1 0 300 200 i * i 208.28.1.130 0 100 0 200 i *> 60.0.0.0 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i r>i180.40.7.0/27 180.40.7.2 0 100 0 i *> 180.40.7.64/27 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *> 180.40.7.128/27 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i r> 208.28.1.0/29 208.28.1.1 0 0 300 i r i 180.40.7.66 0 100 0 300 i *> 208.28.1.64/28 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *> 208.28.1.128/27 208.28.1.1 0 300 200 i * i 208.28.1.130 0 100 0 200 i R3#  config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router bgp 100 R3(config-router)#router bgp 100  BGP is already running; AS is 100 R3(config)#router bgp 100 R3(config-router)#nei 1 17.80.1.2 rout R3(config-router)#nei 17.80.1.2 route-r R3(config-router)#nei 17.80.1.2 route-reflector-client R3(config-router)# *Mar 1 03:35:23.884: %BGP-5-ADJCHANGE: neighbor 17.80.1.2 Down RR client config change R3(config-router)# RACK99AS>4 [Resuming connection 4 to r4 ... ] 03 R4#sh ip bgp BGP table version is 8, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 4.4.4.4/32 0.0.0.0 0 32768 i *> 17.80.1.0/24 0.0.0.0 0 32768 i *> 40.0.0.0 0.0.0.0 0 32768 i R4#sh ip bgp BGP table version is 8, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 4.4.4.4/32 0.0.0.0 0 32768 i *> 17.80.1.0/24 0.0.0.0 0 32768 i *> 40.0.0.0 0.0.0.0 0 32768 i R4# 03:38:15: %BGP-5-ADJCHANGE: neighbor 17.80.1.1 Up R4#sh ip bgp BGP table version is 10, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i1.1.1.1/32 208.28.1.1 0 100 0 300 i * i2.2.2.2/32 180.40.7.2 0 100 0 i *>i3.3.3.3/32 17.80.1.1 0 100 0 i *> 4.4.4.4/32 0.0.0.0 0 32768 i * i5.5.5.5/32 208.28.1.130 0 100 0 200 i * i6.6.6.6/32 208.28.1.1 0 100 0 300 i * i10.0.0.0 208.28.1.1 0 100 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i *> 17.80.1.0/24 0.0.0.0 0 32768 i * i20.0.0.0 180.40.7.2 0 100 0 i *>i30.0.0.0 17.80.1.1 0 100 0 i *> 40.0.0.0 0.0.0.0 0 32768 i * i50.0.0.0 208.28.1.130 0 100 0 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * i180.40.7.0/27 180.40.7.2 0 100 0 i * i180.40.7.64/27 208.28.1.1 0 100 0 300 i * i180.40.7.128/27 208.28.1.1 0 100 0 300 i * i208.28.1.0/29 208.28.1.1 0 100 0 300 i * i208.28.1.64/28 208.28.1.1 0 100 0 300 i * i208.28.1.128/27 208.28.1.130 0 100 0 200 i R4# RACK99AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip bgp BGP table version is 48, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i1.1.1.1/32 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i *> 2.2.2.2/32 0.0.0.0 0 32768 i *>i3.3.3.3/32 180.40.7.3 0 100 0 i * i4.4.4.4/32 17.80.1.2 0 100 0 i * 5.5.5.5/32 180.40.7.66 0 300 200 i * 180.40.7.130 0 300 200 i *> 208.28.1.130 0 0 200 i * i6.6.6.6/32 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i10.0.0.0 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * 208.28.1.130 0 200 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.80.1.0/24 17.80.1.2 0 100 0 i *> 20.0.0.0 0.0.0.0 0 32768 i *>i30.0.0.0 180.40.7.3 0 100 0 i * i40.0.0.0 17.80.1.2 0 100 0 i * 50.0.0.0 180.40.7.66 0 300 200 i --More--   Network Next Hop Metric LocPrf Weight Path * 180.40.7.130 0 300 200 i *> 208.28.1.130 0 0 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.0/27 0.0.0.0 0 32768 i r i180.40.7.64/27 208.28.1.1 0 100 0 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r 208.28.1.130 0 200 300 i r i180.40.7.128/27 208.28.1.1 0 100 0 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r 208.28.1.130 0 200 300 i * i208.28.1.0/29 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i * i208.28.1.64/28 208.28.1.1 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i --More--  * 208.28.1.130 0 200 300 i --More--  r i208.28.1.128/27 208.28.1.1 0 100 0 300 200 i --More--  r 180.40.7.66 0 300 200 i --More--   R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] *M R3(config-router)#exit R3(config)#route-map Pro   ToR2 R3(config-route-map)#set next    ip nex R3(config-route-map)#set ip next-hop 180.40.7.3 % Warning: Next hop address is our address R3(config-route-map)#set ip next-hop 180.40.7.3route-map ToR2  4 R3(config-route-map)#route-map ToR4set ip next-hop 180.40.7.3         7.80.1.1 % Warning: Next hop address is our address R3(config-route-map)#router bgp 100 R3(config-router)#nei 17.80.1.2 rout R3(config-router)#nei 17.80.1.2 route-m R3(config-router)#nei 17.80.1.2 route-map ToR4 out R3(config-router)#nei 17.80.1.2 route-map ToR4 out out 2 out.2 route-map ToR2 out 2 route-map ToR2 out .2 route-map ToR2 out .2 route-map ToR2 out 2 route-map ToR2 out .2 route-map ToR2 out 8.2 route-map ToR2 out0.2 route-map ToR2 out..2 route-map ToR2 out4.2 route-map ToR2 out0.2 route-map ToR2 out..2 route-map ToR2 out7.2 route-map ToR2 out R3(config-router)#^Z R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip bgp BGP table version is 10, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i1.1.1.1/32 208.28.1.1 0 100 0 300 i * i2.2.2.2/32 180.40.7.2 0 100 0 i *>i3.3.3.3/32 17.80.1.1 0 100 0 i *> 4.4.4.4/32 0.0.0.0 0 32768 i * i5.5.5.5/32 208.28.1.1 0 100 0 300 200 i * i6.6.6.6/32 208.28.1.1 0 100 0 300 i * i10.0.0.0 208.28.1.1 0 100 0 300 i * i17.57.100.0/24 208.28.1.1 0 100 0 300 i * i17.57.101.0/24 208.28.1.1 0 100 0 300 i * i17.57.102.0/24 208.28.1.1 0 100 0 300 i * i17.57.103.0/24 208.28.1.1 0 100 0 300 i *> 17.80.1.0/24 0.0.0.0 0 32768 i * i20.0.0.0 180.40.7.2 0 100 0 i *>i30.0.0.0 17.80.1.1 0 100 0 i *> 40.0.0.0 0.0.0.0 0 32768 i * i50.0.0.0 208.28.1.1 0 100 0 300 200 i * i60.0.0.0 208.28.1.1 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * i180.40.7.0/27 180.40.7.2 0 100 0 i * i180.40.7.64/27 208.28.1.1 0 100 0 300 i * i180.40.7.128/27 208.28.1.1 0 100 0 300 i * i208.28.1.0/29 208.28.1.1 0 100 0 300 i * i208.28.1.64/28 208.28.1.1 0 100 0 300 i * i208.28.1.128/27 208.28.1.1 0 100 0 300 200 i R4#clea ip bgp % * in R4#clea ip bgp * insh ip bgp  BGP table version is 28, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *>i1.1.1.1/32 17.80.1.1 0 100 0 300 i *>i2.2.2.2/32 17.80.1.1 0 100 0 i *>i3.3.3.3/32 17.80.1.1 0 100 0 i *> 4.4.4.4/32 0.0.0.0 0 32768 i *>i5.5.5.5/32 17.80.1.1 0 100 0 300 200 i *>i6.6.6.6/32 17.80.1.1 0 100 0 300 i *>i10.0.0.0 17.80.1.1 0 100 0 300 i *>i17.57.100.0/24 17.80.1.1 0 100 0 300 i *>i17.57.101.0/24 17.80.1.1 0 100 0 300 i *>i17.57.102.0/24 17.80.1.1 0 100 0 300 i *>i17.57.103.0/24 17.80.1.1 0 100 0 300 i *> 17.80.1.0/24 0.0.0.0 0 32768 i *>i20.0.0.0 17.80.1.1 0 100 0 i *>i30.0.0.0 17.80.1.1 0 100 0 i *> 40.0.0.0 0.0.0.0 0 32768 i *>i50.0.0.0 17.80.1.1 0 100 0 300 200 i *>i60.0.0.0 17.80.1.1 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path *>i180.40.7.0/27 17.80.1.1 0 100 0 i *>i180.40.7.64/27 17.80.1.1 0 100 0 300 i *>i180.40.7.128/27 17.80.1.1 0 100 0 300 i *>i208.28.1.0/29 17.80.1.1 0 100 0 300 i *>i208.28.1.64/28 17.80.1.1 0 100 0 300 i *>i208.28.1.128/27 17.80.1.1 0 100 0 300 200 i R4# RACK99AS>2 [Resuming connection 2 to r2 ... ] R2#clea ip bgp & 8 * in R2#clea ip bgp * insh ip bgp  BGP table version is 51, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i1.1.1.1/32 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i *> 2.2.2.2/32 0.0.0.0 0 32768 i *>i3.3.3.3/32 180.40.7.3 0 100 0 i *>i4.4.4.4/32 180.40.7.3 0 100 0 i * 5.5.5.5/32 180.40.7.66 0 300 200 i * 180.40.7.130 0 300 200 i *> 208.28.1.130 0 0 200 i * i6.6.6.6/32 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i10.0.0.0 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * 208.28.1.130 0 200 300 i * i17.57.100.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.101.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.102.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.103.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i *>i17.80.1.0/24 180.40.7.3 0 100 0 i *> 20.0.0.0 0.0.0.0 0 32768 i *>i30.0.0.0 180.40.7.3 0 100 0 i *>i40.0.0.0 180.40.7.3 0 100 0 i * 50.0.0.0 180.40.7.66 0 300 200 i --More--   Network Next Hop Metric LocPrf Weight Path * 180.40.7.130 0 300 200 i *> 208.28.1.130 0 0 200 i * i60.0.0.0 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i *> 180.40.7.0/27 0.0.0.0 0 32768 i r i180.40.7.64/27 180.40.7.3 0 100 0 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r 208.28.1.130 0 200 300 i r i180.40.7.128/27 180.40.7.3 0 100 0 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r 208.28.1.130 0 200 300 i * i208.28.1.0/29 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i * i208.28.1.64/28 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * 208.28.1.130 0 200 300 i r 208.28.1.128/27 180.40.7.66 0 300 200 i r 180.40.7.130 0 300 200 i r> 208.28.1.130 0 0 200 i R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] *M R3#hs  sh ip bgp BGP table version is 67, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 1.1.1.1/32 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *>i2.2.2.2/32 180.40.7.2 0 100 0 i *> 3.3.3.3/32 0.0.0.0 0 32768 i *>i4.4.4.4/32 17.80.1.2 0 100 0 i * 5.5.5.5/32 208.28.1.1 0 300 200 i *>i 208.28.1.130 0 100 0 200 i *> 6.6.6.6/32 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i *> 10.0.0.0 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.100.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.101.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i *> 17.57.102.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path *> 17.57.103.0/24 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i r>i17.80.1.0/24 17.80.1.2 0 100 0 i *>i20.0.0.0 180.40.7.2 0 100 0 i *> 30.0.0.0 0.0.0.0 0 32768 i *>i40.0.0.0 17.80.1.2 0 100 0 i * 50.0.0.0 208.28.1.1 0 300 200 i *>i 208.28.1.130 0 100 0 200 i *> 60.0.0.0 208.28.1.1 0 300 i * i 180.40.7.66 0 100 0 300 i r>i180.40.7.0/27 180.40.7.2 0 100 0 i *> 180.40.7.64/27 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i *> 180.40.7.128/27 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i r> 208.28.1.0/29 208.28.1.1 0 0 300 i r i 180.40.7.66 0 100 0 300 i *> 208.28.1.64/28 208.28.1.1 0 0 300 i * i 180.40.7.66 0 100 0 300 i * 208.28.1.128/27 208.28.1.1 0 300 200 i *>i 208.28.1.130 0 100 0 200 i R3# RACK99AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router bgp 100 R2(config-router)#nei 180.40.7.3 nex R2(config-router)#nei 180.40.7.3 next-hop-s R2(config-router)#nei 180.40.7.3 next-hop-self R2(config-router)#^Z R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip bgp BGP table version is 76, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 1.1.1.1/32 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i *>i2.2.2.2/32 180.40.7.2 0 100 0 i *> 3.3.3.3/32 0.0.0.0 0 32768 i *>i4.4.4.4/32 17.80.1.2 0 100 0 i * 5.5.5.5/32 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i *> 6.6.6.6/32 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 10.0.0.0 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.100.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.101.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i *> 17.57.102.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path *> 17.57.103.0/24 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i r>i17.80.1.0/24 17.80.1.2 0 100 0 i *>i20.0.0.0 180.40.7.2 0 100 0 i *> 30.0.0.0 0.0.0.0 0 32768 i *>i40.0.0.0 17.80.1.2 0 100 0 i * 50.0.0.0 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i *> 60.0.0.0 208.28.1.1 0 300 i * i 180.40.7.2 0 100 0 300 i r>i180.40.7.0/27 180.40.7.2 0 100 0 i *> 180.40.7.64/27 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i *> 180.40.7.128/27 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i r> 208.28.1.0/29 208.28.1.1 0 0 300 i r i 180.40.7.2 0 100 0 300 i *> 208.28.1.64/28 208.28.1.1 0 0 300 i * i 180.40.7.2 0 100 0 300 i * 208.28.1.128/27 208.28.1.1 0 300 200 i *>i 180.40.7.2 0 100 0 200 i R3#sh ip bgp     route sum IP routing table name is Default-IP-Routing-Table(0) Route Source Networks Subnets Overhead Memory (bytes) connected 1 4 320 760 static 0 0 0 0 bgp 100 5 13 1152 2736 External: 11 Internal: 7 Local: 0 internal 9 10548 Total 15 17 1472 14044 R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#hs ip       sh ip route sum IP routing table name is Default-IP-Routing-Table(0) Route Source Networks Subnets Overhead Memory (bytes) connected 2 2 256 608 static 0 0 0 0 bgp 100 5 15 1280 3040 External: 0 Internal: 20 Local: 0 internal 9 10548 Total 16 17 1536 14196 R4# RACK99AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip route sum IP routing table name is Default-IP-Routing-Table(0) Route Source Networks Subnets Overhead Memory (bytes) connected 1 6 448 1064 static 0 0 0 0 bgp 300 5 11 1024 2432 External: 11 Internal: 5 Local: 0 internal 9 10548 Total 15 17 1472 14044 R1# RACK99AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip route sum IP routing table name is Default-IP-Routing-Table(0) IP routing table maximum-paths is 32 Route Source Networks Subnets Overhead Memory (bytes) connected 1 5 384 912 static 0 0 0 0 bgp 300 5 12 1088 2584 External: 0 Internal: 17 Local: 0 internal 9 10548 Total 15 17 1472 14044 S6# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip rout sy um IP routing table name is Default-IP-Routing-Table(0) IP routing table maximum-paths is 32 Route Source Networks Subnets Overhead Memory (bytes) connected 1 3 256 608 static 0 0 0 0 bgp 200 5 14 1216 2888 External: 19 Internal: 0 Local: 0 internal 9 10548 Total 15 17 1472 14044 S5# RACK99AS>1 [Resuming connection 1 to r1 ... ] R1#tclsh Translating "tclsh" Translating "tclsh" % Unknown command or computer name, or unable to find computer address R1#foreach test { ^ % Invalid input detected at '^' marker. R1#17.57.100.1 Trying 17.57.100.1 ... Open 17.57.100.2 17.57.101.1 17.5 Password required, but none set [Connection to 17.57.100.1 closed by foreign host] R1# R1# RACK99AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 03:41:43 R2#tclsh R2(tcl)#foreach test { +>(tcl)#17.57.100.1 +>(tcl)#17.57.100.2 +>(tcl)#17.57.101.1 +>(tcl)#17.57.102.1 +>(tcl)#17.57.103.1 +>(tcl)#208.28.1.65 +>(tcl)#208.28.1.66 +>(tcl)#208.28.1.129 +>(tcl)#208.28.1.130 +>(tcl)#180.40.7.65 +>(tcl)#180.40.7.66 +>(tcl)#180.40.7.129 +>(tcl)#180.40.7.130 +>(tcl)#208.28.1.1 +>(tcl)#208.28.1.2 +>(tcl)#180.40.7.2 +>(tcl)#180.40.7.3 +>(tcl)#17.80.1.1 +>(tcl)#17.80.1.2 +>(tcl)#10.1.1.1 +>(tcl)#20.1.1.1 +>(tcl)#30.1.1.1 +>(tcl)#40.1.1.1 +>(tcl)#50.1.1.1 +>(tcl)#60.1.1.1 +>(tcl)#1.1.1.1 +>(tcl)#2.2.2.2 +>(tcl)#3.3.3.3 +>(tcl)#4.4.4.4 +>(tcl)#5.5.5.5 +>(tcl)#6.6.6.6 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/57 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/74/88 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: .. Success rate is 0 percent (0/2) Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/62/69 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/28/28 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/64/68 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 112/114/116 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/62/65 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/28/28 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/57 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 5.5.5.5, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 6.6.6.6, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0 R2(config-if)#fma map ip 180.40.7.65 201 ^ % Invalid input detected at '^' marker. R2(config-if)#fma map ip 180.40.7.65 201 a map ip 180.40.7.65 201  map ip 180.40.7.65 201 a map ip 180.40.7.65 201 m map ip 180.40.7.65 201  ^ % Invalid input detected at '^' marker. R2(config-if)#fam map ip 180.40.7.65 201 ram map ip 180.40.7.65 201  R2(config-if)#^Z R2# *Mar 1 03:45:39.534: %SYS-5-CONFIG_I: Configured from console by console R2#tclsh R2(tcl)#foreach test { +>(tcl)#17.57.100.1 +>(tcl)#17.57.100.2 +>(tcl)#17.57.101.1 +>(tcl)#17.57.102.1 +>(tcl)#17.57.103.1 +>(tcl)#208.28.1.65 +>(tcl)#208.28.1.66 +>(tcl)#208.28.1.129 +>(tcl)#208.28.1.130 +>(tcl)#180.40.7.65 +>(tcl)#180.40.7.66 +>(tcl)#180.40.7.129 +>(tcl)#180.40.7.130 +>(tcl)#208.28.1.1 +>(tcl)#208.28.1.2 +>(tcl)#180.40.7.2 +>(tcl)#180.40.7.3 +>(tcl)#17.80.1.1 +>(tcl)#17.80.1.2 +>(tcl)#10.1.1.1 +>(tcl)#20.1.1.1 +>(tcl)#30.1.1.1 +>(tcl)#40.1.1.1 +>(tcl)#50.1.1.1 +>(tcl)#60.1.1.1 +>(tcl)#1.1.1.1 +>(tcl)#2.2.2.2 +>(tcl)#3.3.3.3 +>(tcl)#4.4.4.4 +>(tcl)#5.5.5.5 +>(tcl)#6.6.6.6 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/62/68 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/61 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/60/64 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 112/118/124 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/56/56 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 29/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 64/64/65 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 116/116/116 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 36/36/37 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 36/36/36 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 36/36/36 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/34/36 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 36/36/37 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/34/36 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 36/36/36 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 5.5.5.5, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 6.6.6.6, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms R2#conf    config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0 R2(config-if)#' int s 1/0fram map ip 180.40.7.65 201  201 6 201  R2(config-if)#^Z R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#tclsh R3(tcl)#foreach test { +>(tcl)#17.57.100.1 +>(tcl)#17.57.100.2 +>(tcl)#17.57.101.1 +>(tcl)#17.57.102.1 +>(tcl)#17.57.103.1 +>(tcl)#208.28.1.65 +>(tcl)#208.28.1.66 +>(tcl)#208.28.1.129 +>(tcl)#208.28.1.130 +>(tcl)#180.40.7.65 +>(tcl)#180.40.7.66 +>(tcl)#180.40.7.129 +>(tcl)#180.40.7.130 +>(tcl)#208.28.1.1 +>(tcl)#208.28.1.2 +>(tcl)#180.40.7.2 +>(tcl)#180.40.7.3 +>(tcl)#17.80.1.1 +>(tcl)#17.80.1.2 +>(tcl)#10.1.1.1 +>(tcl)#20.1.1.1 +>(tcl)#30.1.1.1 +>(tcl)#40.1.1.1 +>(tcl)#50.1.1.1 +>(tcl)#60.1.1.1 +>(tcl)#1.1.1.1 +>(tcl)#2.2.2.2 +>(tcl)#3.3.3.3 +>(tcl)#4.4.4.4 +>(tcl)#5.5.5.5 +>(tcl)#6.6.6.6 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/61 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 112/114/116 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 96/102/108 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/61 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: .. Success rate is 0 percent (0/2) Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 61/62/64 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 64/68/72 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/66/77 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 5.5.5.5, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 6.6.6.6, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#tclsh R4(tcl)#foreach test { +>(tcl)#17.57.100.1 +>(tcl)#17.57.100.2 +>(tcl)#17.57.101.1 +>(tcl)#17.57.102.1 +>(tcl)#17.57.103.1 +>(tcl)#208.28.1.65 +>(tcl)#208.28.1.66 +>(tcl)#208.28.1.129 +>(tcl)#208.28.1.130 +>(tcl)#180.40.7.65 +>(tcl)#180.40.7.66 +>(tcl)#180.40.7.129 +>(tcl)#180.40.7.130 +>(tcl)#208.28.1.1 +>(tcl)#208.28.1.2 +>(tcl)#180.40.7.2 +>(tcl)#180.40.7.3 +>(tcl)#17.80.1.1 +>(tcl)#17.80.1.2 +>(tcl)#10.1.1.1 +>(tcl)#20.1.1.1 +>(tcl)#30.1.1.1 +>(tcl)#40.1.1.1 +>(tcl)#50.1.1.1 +>(tcl)#60.1.1.1 +>(tcl)#1.1.1.1 +>(tcl)#2.2.2.2 +>(tcl)#3.3.3.3 +>(tcl)#4.4.4.4 +>(tcl)#5.5.5.5 +>(tcl)#6.6.6.6 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/62/64 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 44/44/44 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 72/72/72 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 64/72/80 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 28/28/28 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 5.5.5.5, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 2, 100-byte ICMP Echos to 6.6.6.6, timeout is 2 seconds: !! Success rate is 100 percent (2/2), round-trip min/avg/max = 60/60/60 ms R4# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#macro name testbgp Enter macro commands one per line. End with the character '@'. do ping 17.57.100.1 do ping 17.57.100.2 do ping 17.57.101.1 do ping 17.57.102.1 do ping 17.57.103.1 do ping 208.28.1.65 do ping 208.28.1.66 do ping 208.28.1.129 do ping 208.28.1.130 do ping 180.40.7.65 do ping 180.40.7.66 do ping 180.40.7.129 do ping 180.40.7.130 do ping 208.28.1.1 do ping 208.28.1.2 do ping 180.40.7.2 do ping 180.40.7.3 do ping 17.80.1.1 do ping 17.80.1.2 do ping 10.1.1.1 do ping 20.1.1.1 do ping 30.1.1.1 do ping 40.1.1.1 do ping 50.1.1.1 do ping 60.1.1.1 do ping 1.1.1.1 do ping 2.2.2.2 do ping 3.3.3.3 do ping 4.4.4.4 do ping 5.5.5.5 do ping 6.6.6.6 @ S5(config)# S5(config)#macro global apply testbgp Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/12 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/44/44 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/5/16 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/8/28 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/31/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/31/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 5.5.5.5, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 6.6.6.6, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5(config)#^Z S5# RACK99AS>6 [Resuming connection 6 to r6 ... ] S6#macro name testbgp ^ % Invalid input detected at '^' marker. S6#do ping 17.57.100.1 ^ % Invalid input detected at '^' marker. S6#do ping 17.57.100.2 ^ % Invalid input detected at '^' marker. S6#do ping 17.57.101.1 ^ % Invalid input detected at '^' marker. S6#do ping 17.57.102.1 ^ % Invalid input detected at '^' marker. S6#do ping 17.57.103.1 ^ % Invalid input detected at '^' marker. S6#do ping 208.28.1.65 ^ % Invalid input detected at '^' marker. S6#do ping 208.28.1.66 ^ % Invalid input detected at '^' marker. S6#do ping 208.28.1.129 ^ % Invalid input detected at '^' marker. S6#do ping 208.28.1.130 ^ % Invalid input detected at '^' marker. S6#do ping 180.40.7.65 ^ % Invalid input detected at '^' marker. S6#do ping 180.40.7.66 ^ % Invalid input detected at '^' marker. S6#do ping 180.40.7.129 ^ % Invalid input detected at '^' marker. S6#do ping 180.40.7.130 ^ % Invalid input detected at '^' marker. S6#do ping 208.28.1.1 ^ % Invalid input detected at '^' marker. S6#do ping 208.28.1.2 ^ % Invalid input detected at '^' marker. S6#do ping 180.40.7.2 ^ % Invalid input detected at '^' marker. S6#do ping 180.40.7.3 ^ % Invalid input detected at '^' marker. S6#do ping 17.80.1.1 ^ % Invalid input detected at '^' marker. S6#do ping 17.80.1.2 ^ % Invalid input detected at '^' marker. S6#do ping 10.1.1.1 ^ % Invalid input detected at '^' marker. S6#do ping 20.1.1.1 ^ % Invalid input detected at '^' marker. S6#do ping 30.1.1.1 ^ % Invalid input detected at '^' marker. S6#do ping 40.1.1.1 ^ % Invalid input detected at '^' marker. S6#do ping 50.1.1.1 ^ % Invalid input detected at '^' marker. S6#do ping 60.1.1.1 ^ % Invalid input detected at '^' marker. S6#do ping 1.1.1.1 ^ % Invalid input detected at '^' marker. S6#do ping 2.2.2.2 ^ % Invalid input detected at '^' marker. S6#do ping 3.3.3.3 ^ % Invalid input detected at '^' marker. S6#do ping 4.4.4.4 ^ % Invalid input detected at '^' marker. S6#do ping 5.5.5.5 ^ % Invalid input detected at '^' marker. S6#do ping 6.6.6.6 ^ % Invalid input detected at '^' marker. S6#@ % Unknown command or computer name, or unable to find computer address S6# S6#macro global apply testbgp ^ % Invalid input detected at '^' marker. S6# S6# S6#config Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. S6(config)#macro name testbgp Enter macro commands one per line. End with the character '@'. do ping 17.57.100.1 do ping 17.57.100.2 do ping 17.57.101.1 do ping 17.57.102.1 do ping 17.57.103.1 do ping 208.28.1.65 do ping 208.28.1.66 do ping 208.28.1.129 do ping 208.28.1.130 do ping 180.40.7.65 do ping 180.40.7.66 do ping 180.40.7.129 do ping 180.40.7.130 do ping 208.28.1.1 do ping 208.28.1.2 do ping 180.40.7.2 do ping 180.40.7.3 do ping 17.80.1.1 do ping 17.80.1.2 do ping 10.1.1.1 do ping 20.1.1.1 do ping 30.1.1.1 do ping 40.1.1.1 do ping 50.1.1.1 do ping 60.1.1.1 do ping 1.1.1.1 do ping 2.2.2.2 do ping 3.3.3.3 do ping 4.4.4.4 do ping 5.5.5.5 do ping 6.6.6.6 @ S6(config)# S6(config)#macro global apply testbgp Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.101.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.102.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.103.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/7/20 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/42/44 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 68/71/72 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/67/96 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/68 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 30.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 40.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 50.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 60.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 5.5.5.5, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 6.6.6.6, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms S6(config)#^Z S6# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/- ^ % Invalid input detected at '^' marker. R3(config)#int s 1/- 0 R3(config-if)#fram map ip 2082.  .28. .1.1 2 301 R3(config-if)#fram map ip 208.28.1.1 301  301 2 301  R3(config-if)#^Z R3# *Mar 1 03:50:01.459: %SYS-5-CONFIG_I: Configured from console by console R3# RACK99AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b bgp router bgp 300 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes network 1.1.1.1 mask 255.255.255.255 network 10.0.0.0 network 180.40.7.64 mask 255.255.255.224 network 180.40.7.128 mask 255.255.255.224 network 208.28.1.0 mask 255.255.255.248 network 208.28.1.64 mask 255.255.255.240 neighbor 17.57.100.2 remote-as 300 neighbor 180.40.7.65 remote-as 100 neighbor 180.40.7.129 remote-as 100 neighbor 208.28.1.2 remote-as 100 neighbor 208.28.1.65 remote-as 200 no auto-summary ! no ip http server ip classless ! ! ! line con 0 --More--   R1# RACK99AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run } b     | b bgp router bgp 100 no synchronization bgp router-id 2.2.2.2 bgp log-neighbor-changes network 2.2.2.2 mask 255.255.255.255 network 20.0.0.0 network 180.40.7.0 mask 255.255.255.224 neighbor 180.40.7.3 remote-as 100 neighbor 180.40.7.3 next-hop-self neighbor 180.40.7.66 remote-as 300 neighbor 180.40.7.130 remote-as 300 neighbor 208.28.1.130 remote-as 200 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! --More--   R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes network 3.3.3.3 mask 255.255.255.255 network 30.0.0.0 neighbor 17.80.1.2 remote-as 100 neighbor 17.80.1.2 route-reflector-client neighbor 17.80.1.2 route-map ToR4 out neighbor 180.40.7.2 remote-as 100 neighbor 180.40.7.2 route-map ToR2 out neighbor 208.28.1.1 remote-as 300 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! route-map ToR2 permit 10 set ip next-hop 180.40.7.3 ! --More--  route-map ToR4 permit 10 set ip next-hop 17.80.1.1 ! ! ! ! ! ! dial-peer cor custom ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 login ! ! end --More--   R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b bgp router bgp 100 no synchronization bgp router-id 4.4.4.4 bgp log-neighbor-changes network 4.4.4.4 mask 255.255.255.255 network 17.80.1.0 mask 255.255.255.0 network 40.0.0.0 neighbor 17.80.1.1 remote-as 100 no auto-summary ! no ip http server no ip http secure-server ip classless ! ! ! ! ! dial-peer cor custom ! ! ! ! --More--   R4# RACK99AS>5 [Resuming connection 5 to r5 ... ] 03 S5#sh run | b bgp macro name testbgp do ping 17.57.100.1 do ping 17.57.100.2 do ping 17.57.101.1 do ping 17.57.102.1 do ping 17.57.103.1 do ping 208.28.1.65 do ping 208.28.1.66 do ping 208.28.1.129 do ping 208.28.1.130 do ping 180.40.7.65 do ping 180.40.7.66 do ping 180.40.7.129 do ping 180.40.7.130 do ping 208.28.1.1 do ping 208.28.1.2 do ping 180.40.7.2 do ping 180.40.7.3 do ping 17.80.1.1 do ping 17.80.1.2 do ping 10.1.1.1 do ping 20.1.1.1 do ping 30.1.1.1 --More--   S5#sh run | b bgp     router router bgp 200 no synchronization bgp router-id 5.5.5.5 bgp log-neighbor-changes network 5.5.5.5 mask 255.255.255.255 network 50.0.0.0 network 208.28.1.128 mask 255.255.255.224 neighbor 208.28.1.66 remote-as 300 neighbor 208.28.1.129 remote-as 100 no auto-summary ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous --More--   S5# RACK99AS>6 [Resuming connection 6 to r6 ... ] 03: S6#sh run | b router router bgp 300 no synchronization bgp router-id 6.6.6.6 bgp log-neighbor-changes network 6.6.6.6 mask 255.255.255.255 network 17.57.100.0 mask 255.255.255.0 network 17.57.101.0 mask 255.255.255.0 network 17.57.102.0 mask 255.255.255.0 network 17.57.103.0 mask 255.255.255.0 network 60.0.0.0 neighbor 17.57.100.1 remote-as 300 no auto-summary ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 --More--   S6# RACK99AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip as R2(config)#ip as-path acc R2(config)#ip as-path access-list ? <1-500> AS path access list number R2(config)#ip as-path access-list 1 ? deny Specify packets to reject permit Specify packets to forward R2(config)#ip as-path access-list 1 per ? LINE A regular-expression to match BGP AS paths. Use "ctrl-v ?" to enter "?" R2(config)#ip as-path access-list 1 per _200$ R2(config)#route-map Prob2 R2(config-route-map)#match ip as R2(config-route-map)#match ip as     as R2(config-route-map)#match as-path ? <1-500> AS path access-list R2(config-route-map)#match as-path 1 R2(config-route-map)#set loca R2(config-route-map)#set local-preference 99 R2(config-route-map)#set local-preference 99match as-path 1 route-map Prob2 20 R2(config-route-map)#route  r bgp 100 R2(config-router)#nei 208.28.1.130 route R2(config-router)#nei 208.28.1.130 route-m R2(config-router)#nei 208.28.1.130 route-map Prob2 in R2(config-router)#^Z R2#sh ip bgp *Mar 1 03:58:25.834: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip bgp reg R2#sh ip bgp regexp ? LINE A regular-expression to match BGP AS paths. Use "ctrl-v ?" to enter "?" R2#sh ip bgp regexp        ? A.B.C.D IP prefix /, e.g., 35.0.0.0/8 A.B.C.D Network in the BGP routing table to display cidr-only Display only routes with non-natural netmasks community Display routes matching the communities community-list Display routes matching the community-list dampening Display detailed information about dampening filter-list Display routes conforming to the filter-list inconsistent-as Display only routes with inconsistent origin ASs injected-paths Display all injected paths ipv4 Address family labels Display Labels for IPv4 NLRI specific information neighbors Detailed information on TCP and BGP neighbor connections paths Path information peer-group Display information on peer-groups prefix-list Display routes matching the prefix-list quote-regexp Display routes matching the AS path "regular expression" regexp Display routes matching the AS path regular expression rib-failure Display bgp routes that failed to install in the routing table (RIB) route-map Display routes matching the route-map summary Summary of BGP neighbor status vpnv4 Display VPNv4 NLRI specific information --More--   R2#sh ip bgp fil R2#sh ip bgp filter-list ? <1-500> Regular expression access list number R2#sh ip bgp filter-list 1 BGP table version is 51, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 5.5.5.5/32 180.40.7.66 0 300 200 i * 180.40.7.130 0 300 200 i *> 208.28.1.130 0 0 200 i * 50.0.0.0 180.40.7.66 0 300 200 i * 180.40.7.130 0 300 200 i *> 208.28.1.130 0 0 200 i r 208.28.1.128/27 180.40.7.66 0 300 200 i r 180.40.7.130 0 300 200 i r> 208.28.1.130 0 0 200 i R2#sh ip bgp 50.0.0;.0   .0 BGP routing table entry for 50.0.0.0/8, version 12 Paths: (3 available, best #3, table Default-IP-Routing-Table) Advertised to non peer-group peers: 180.40.7.3 180.40.7.66 180.40.7.130 300 200 180.40.7.66 from 180.40.7.66 (1.1.1.1) Origin IGP, localpref 100, valid, external 300 200 180.40.7.130 from 180.40.7.130 (1.1.1.1) Origin IGP, localpref 100, valid, external 200 208.28.1.130 from 208.28.1.130 (5.5.5.5) Origin IGP, metric 0, localpref 100, valid, external, best R2#clea ip bgp * in R2#clea ip bgp * insh ip bgp 50.0.0.0 BGP routing table entry for 50.0.0.0/8, version 53 Paths: (3 available, best #1, table Default-IP-Routing-Table) Flag: 0x820 Advertised to non peer-group peers: 180.40.7.3 180.40.7.130 208.28.1.130 300 200 180.40.7.66 from 180.40.7.66 (1.1.1.1) Origin IGP, localpref 100, valid, external, best 300 200 180.40.7.130 from 180.40.7.130 (1.1.1.1) Origin IGP, localpref 100, valid, external 200 208.28.1.130 from 208.28.1.130 (5.5.5.5) Origin IGP, metric 0, localpref 99, valid, external R2#sh ip bgp 50.0.0.0clea ip bgp * in sh ip bgp 50.0.0.0filter-list 1 BGP table version is 54, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i5.5.5.5/32 180.40.7.3 0 100 0 300 200 i *> 180.40.7.66 0 300 200 i * 180.40.7.130 0 300 200 i * 208.28.1.130 0 99 0 200 i * i50.0.0.0 180.40.7.3 0 100 0 300 200 i *> 180.40.7.66 0 300 200 i * 180.40.7.130 0 300 200 i * 208.28.1.130 0 99 0 200 i r i208.28.1.128/27 180.40.7.3 0 100 0 300 200 i r> 180.40.7.66 0 300 200 i r 180.40.7.130 0 300 200 i r 208.28.1.130 0 99 0 200 i R2#sh run | b bgp router bgp 100 no synchronization bgp router-id 2.2.2.2 bgp log-neighbor-changes network 2.2.2.2 mask 255.255.255.255 network 20.0.0.0 network 180.40.7.0 mask 255.255.255.224 neighbor 180.40.7.3 remote-as 100 neighbor 180.40.7.3 next-hop-self neighbor 180.40.7.66 remote-as 300 neighbor 180.40.7.130 remote-as 300 neighbor 208.28.1.130 remote-as 200 neighbor 208.28.1.130 route-map Prob2 in no auto-summary ! ip classless ! ip as-path access-list 1 permit _200$ no ip http server no ip http secure-server ! ! route-map Prob2 permit 10 --More--   match as-path 1 set local-preference 99 ! route-map Prob2 permit 20 ! ! ! ! ! ! dial-peer cor custom ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 login ! --More--   R2#sh ip bgp BGP table version is 54, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i1.1.1.1/32 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i *> 2.2.2.2/32 0.0.0.0 0 32768 i *>i3.3.3.3/32 180.40.7.3 0 100 0 i *>i4.4.4.4/32 180.40.7.3 0 100 0 i * i5.5.5.5/32 180.40.7.3 0 100 0 300 200 i *> 180.40.7.66 0 300 200 i * 180.40.7.130 0 300 200 i * 208.28.1.130 0 99 0 200 i * i6.6.6.6/32 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i10.0.0.0 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i * i17.57.100.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.101.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.102.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.103.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i *>i17.80.1.0/24 180.40.7.3 0 100 0 i *> 20.0.0.0 0.0.0.0 0 32768 i *>i30.0.0.0 180.40.7.3 0 100 0 i *>i40.0.0.0 180.40.7.3 0 100 0 i --More--   R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#do sh ace cess-list R2(config)#ip access-list ? extended Extended Access List log-update Control access list log updates logging Control access list logging resequence Resequence Access List standard Standard Access List R2(config)#ip access-list ex Prib    To100 R2(config-ext-nacl)#per ip access-list ex To100nip access-list ex To100 ip access-list ex To100oip access-list ex To100 ^ % Invalid input detected at '^' marker. R2(config-ext-nacl)#n oip access-list ex To100ip access-list ex To100 ip access-list ex To100 oip access-list ex To100 ip access-list ex To100 R2(config)#no ip access-list ex To100 oip access-list ex To100ip access-list ex To100  To100  To100 s To100t To100 R2(config-std-nacl)#per 17.57.100.0 R2(config-std-nacl)#per 17.57.100.0ip access-list st To100 1 R2(config-std-nacl)#ip access-list st To101per 17.57.100.0 0.0 1.0 R2(config-std-nacl)#eixt ^ % Invalid input detected at '^' marker. R2(config-std-nacl)#exit R2(config)#exitixtper 17.57.101.0ip access-list st To1011     From  PP R2(config-std-nacl)#per 180.40.7.130 R2(config-std-nacl)#per 180.40.7.130ip access-list st FromPP  FR R2(config-std-nacl)#ip access-list st FromFRper 180.40.7.130 0   66 R2(config-std-nacl)#exit R2(config)#route-map Prob3 R2(config-route-map)#match ip add To100 R2(config-route-map)#match ? as-path Match BGP AS path list clns CLNS information community Match BGP community list extcommunity Match BGP/VPN extended community list interface Match first hop interface of route ip IP specific information ipv6 IPv6 specific information length Packet length metric Match metric of route mpls-label Match routes which have MPLS labels nlri BGP NLRI type policy-list Match IP policy list route-type Match route-type of route tag Match tag of route R2(config-route-map)#match ip ? address Match address of route or match packet next-hop Match next-hop address of route route-source Match advertising source address of route R2(config-route-map)#match ip rou R2(config-route-map)#match ip route-source ? <1-99> IP access-list number <1300-1999> IP access-list number (expanded range) WORD IP standard access-list name prefix-list Match entries of prefix-lists R2(config-route-map)#match ip route-source FromFR R2(config-route-map)#set w R2(config-route-map)#set weight 1111 R2(config-route-map)#set weight 1111match ip route-source FromFRadd To100 route-map Prob3 exit route-map Prob3 20 R2(config-route-map)#route-map Prob3 20set weight 1111 match ip route-source FromFRadd To100  1 R2(config-route-map)#match ip add To101route-map Prob3 20set weight 1111 match ip route-source FromFR  PP R2(config-route-map)#match ip route-source FromPPadd To101 route-map Prob3 20set weight 1111     3333 R2(config-route-map)#set weight 3333match ip route-source FromPPadd To101 route-map Prob3 20  30 R2(config-route-map)#routr bgp       er b gp     gp 100 R2(config-router)#nei 180.40.7.130 rout R2(config-router)#nei 180.40.7.130 route-m R2(config-router)#nei 180.40.7.130 route-map Prob3 in % "Prob3" used as BGP inbound route-map, route source match not supported R2(config-router)#edxi   xit R2(config)#no    no exitnei 180.40.7.130 route-map Prob3 inrouter bgp 100 -map Prob3 30set weight 3333 match ip route-source FromPPadd To101 route-map Prob3 20match ip add To101route-source FromPPset weight 3333 route-map Prob3 30r bgp 100 nei 180.40.7.130 route-map Prob3 inexit no    do sh run | b route-map neighbor 180.40.7.130 route-map Prob3 in neighbor 208.28.1.130 remote-as 200 neighbor 208.28.1.130 route-map Prob2 in no auto-summary ! ip classless ! ip as-path access-list 1 permit _200$ no ip http server no ip http secure-server ! ip access-list standard FromFR permit 180.40.7.66 ip access-list standard FromPP permit 180.40.7.130 ip access-list standard To100 permit 17.57.100.0 ip access-list standard To101 permit 17.57.101.0 ! ! route-map Prob3 permit 10 match ip address To100 --More--   match ip route-source FromFR set weight 1111 ! route-map Prob3 permit 20 match ip address To101 match ip route-source FromPP set weight 3333 ! route-map Prob3 permit 30 ! route-map Prob2 permit 10 match as-path 1 set local-preference 99 ! route-map Prob2 permit 20 ! ! ! ! ! ! dial-peer cor custom ! --More--   R2(config)#no ip access-list standard FromFR R2(config)#no ip access-list standard FromPP R2(config)# R2(config)#! R2(config)#! R2(config)#no route-map Prob3 R2(config)#route-map Prob3a permit 10 R2(config-route-map)# match ip address To100 R2(config-route-map)# set weight 1111 R2(config-route-map)#! R2(config-route-map)#route-map Prob3a permit 20 R2(config-route-map)#! R2(config-route-map)#! R2(config-route-map)#route-map Prob3b permit 10 R2(config-route-map)# match ip address To101 R2(config-route-map)# set weight 3333 R2(config-route-map)# R2(config-route-map)#route-map Prob3b permit 20 R2(config-route-map)# R2(config-route-map)#routr bgp       er bgp 100 R2(config-router)#nei 180.40.7.130 rout R2(config-router)#nei 180.40.7.130 route-m R2(config-router)#nei 180.40.7.130 route-map P ro  Prob3b in R2(config-router)#nei 180.40.7.130 route-map Prob3b in in a in route-map Prob3a in  route-map Prob3a in  route-map Prob3a in 6 route-map Prob3a in6 route-map Prob3a in R2(config-router)#^Z R2#sh   *Mar 1 04:10:45.587: %SYS-5-CONFIG_I: Configured from console by console R2#sh  clea ip bgp * in R2#sh ip bgp reg _300$ BGP table version is 56, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i1.1.1.1/32 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i * i6.6.6.6/32 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i10.0.0.0 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 0 300 i * 180.40.7.130 0 0 300 i * 208.28.1.130 0 200 300 i * i17.57.100.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 1111 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.101.0/24 180.40.7.3 0 100 0 300 i --More--   Network Next Hop Metric LocPrf Weight Path * 180.40.7.66 0 300 i *> 180.40.7.130 3333 300 i * 208.28.1.130 0 200 300 i * i17.57.102.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i17.57.103.0/24 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i * i60.0.0.0 180.40.7.3 0 100 0 300 i *> 180.40.7.66 0 300 i * 180.40.7.130 0 300 i * 208.28.1.130 0 200 300 i r i180.40.7.64/27 180.40.7.3 0 100 0 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i r 208.28.1.130 0 200 300 i r i180.40.7.128/27 180.40.7.3 0 100 0 300 i r> 180.40.7.66 0 0 300 i r 180.40.7.130 0 0 300 i --More--   R2#sh run | b router router bgp 100 no synchronization bgp router-id 2.2.2.2 bgp log-neighbor-changes network 2.2.2.2 mask 255.255.255.255 network 20.0.0.0 network 180.40.7.0 mask 255.255.255.224 neighbor 180.40.7.3 remote-as 100 neighbor 180.40.7.3 next-hop-self neighbor 180.40.7.66 remote-as 300 neighbor 180.40.7.66 route-map Prob3a in neighbor 180.40.7.130 remote-as 300 neighbor 180.40.7.130 route-map Prob3b in neighbor 208.28.1.130 remote-as 200 neighbor 208.28.1.130 route-map Prob2 in no auto-summary ! ip classless ! ip as-path access-list 1 permit _200$ no ip http server no ip http secure-server ! --More--  ip access-list standard To100 permit 17.57.100.0 ip access-list standard To101 permit 17.57.101.0 ! ! route-map Prob2 permit 10 match as-path 1 set local-preference 99 ! route-map Prob2 permit 20 ! route-map Prob3a permit 10 match ip address To100 set weight 1111 ! route-map Prob3a permit 20 ! route-map Prob3b permit 10 match ip address To101 set weight 3333 ! route-map Prob3b permit 20 --More--  ! ! ! ! ! ! dial-peer cor custom ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 login ! ! end R2# R2#