=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.04.24 17:03:05 =~=~=~=~=~=~=~=~=~=~=~= RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down FastEthernet0/21 unassigned YES unset down down --More--   S5(config)#int vlan 10 S5(config-if)#ip add 05:52:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to down S5(config-if)#ip add 208.28.1.65 n 255.255.255.240 S5(config-if)#do sh ip in nt brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual down down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down --More--   S5(config-if)#sh  do sh v;a  lan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S5(config-if)#vlan 10 S5(config-vlan)#name ToR1 S5(config-vlan)#do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S5(config-vlan)#exit S5(config)#exitdo sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 ToR1 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 --More--   S5(config)#sh    do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual up down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down --More--   S5(config)#do sh int turn   runk Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1 S5(config)# 05:55:35: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up S5(config)# S5(config)# S5(config)# S5(config)#vlan 20 S5(config-vlan)#name Tr oR2 S5(config-vlan)#int vlan 20 S5(config-if)#ip add 20 05:56:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down S5(config-if)#ip add 208.28.1.130 255.255.255.223 4 S5(config-if)# 05:56:38: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up S5(config-if)#exit S5(config)#vlan 34 S5(config-vlan)#name BlueSuede S5(config-vlan)#int fa 0/3 S5(config-if)#swm  S5(config-if)#switchport mode acc S5(config-if)#swi S5(config-if)#switchport acce S5(config-if)#switchport access vlan 34 S5(config-if)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S6# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5(config-if)#do sh vtp status VTP Version : 2 Configuration Revision : 3 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x54 0x66 0xDC 0x62 0x2C 0xCA 0xE7 0x6F Configuration last modified by 208.28.1.65 at 3-1-93 05:57:44 Local updater ID is 208.28.1.65 on interface Vl10 (lowest numbered VLAN interface found) S5(config-if)#exit S5(config)#vtp dom S5(config)#vtp domain Gracek lane d Changing VTP domain name from NULL to Graceland S5(config)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#sh vlanen sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 ToR1 active 20 ToR2 active 34 BlueSuede active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 --More--   S6#sh vtp stat VTP Version : 2 Configuration Revision : 3 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x86 0x53 0xAB 0x6E 0x46 0xF8 0x84 0xA6 Configuration last modified by 208.28.1.65 at 3-1-93 05:57:44 Local updater ID is 0.0.0.0 (no valid interface found) S6#sh int tur ^ % Invalid input detected at '^' marker. S6#sh int tur  ru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#vtp pru S6(config)#vtp pruning ? S6(config)#vtp pruning Pruning switched on S6(config)#^Z S6#config tsh int tru 06:00:26: %SYS-5-CONFIG_I: Configured from console by console S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh s vtp stat VTP Version : 2 Configuration Revision : 4 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x2D 0x91 0x18 0x58 0x14 0x02 0x34 0xF5 Configuration last modified by 0.0.0.0 at 3-1-93 06:00:24 Local updater ID is 0.0.0.0 (no valid interface found) S6# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5(config)#do sh vtp stat VTP Version : 2 Configuration Revision : 4 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x2D 0x91 0x18 0x58 0x14 0x02 0x34 0xF5 Configuration last modified by 0.0.0.0 at 3-1-93 06:00:24 Local updater ID is 208.28.1.65 on interface Vl10 (lowest numbered VLAN interface found) S5(config)#s do sh tun int Tunnels ======= S5(config)#do sh tun int       int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1 S5(config)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#sh vtp stat VTP Version : 2 Configuration Revision : 4 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x2D 0x91 0x18 0x58 0x14 0x02 0x34 0xF5 Configuration last modified by 0.0.0.0 at 3-1-93 06:00:24 Local updater ID is 0.0.0.0 (no valid interface found) S6#sh vtp statint tru  Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh     RACK13AS>5 [Resuming connection 5 to r5 ... ] S5(config)#s ^Z S5#sh spa 06:02:40: %SYS-5-CONFIG_I: Configured from console by console S5#sh span vlan 10 VLAN0010 Spanning tree enabled protocol ieee Root ID Priority 32778 Address 0013.80e2.0000 Cost 19 Port 24 (FastEthernet0/24) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32778 (priority 32768 sys-id-ext 10) Address 0013.80e2.1c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 Interface Role Sts Cost Prio.Nbr Type ---------------- ---- --- --------- -------- -------------------------------- Fa0/24 Root FWD 19 128.24 P2p S5#sh span vlan 10config t sh ver en sh verconfig tsh span vlan 10 config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int s   fa 0/1 S5(config-if)#sw S5(config-if)#switchport mode access S5(config-if)#switchport mode access            a    access vlan 10 S5(config-if)#^Z S5# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/3 S6(config-if)#int fa 0/3 4 S6(config-if)#sw S6(config-if)#switchport mode  S6(config-if)#switchport mode acc S6(config-if)#sw acc vlan 34 S6(config-if)#int fa 0/\ 2 S6(config-if)#int fa 0/2sw acc vlan 34itchport mode acc S6(config-if)#switchport mode accint fa 0/2 sw acc vlan 34  20 S6(config-if)#^Z S6#sh 06:04:24: %SYS-5-CONFIG_I: Configured from console by console S6#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6# RACK13AS>5 [Resuming connection 5 to r5 ... ] 0 S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1 S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1 S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1 S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,34 S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,34 S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,34 S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,34 S5#sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,20,34 S5# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/1 S6(config-if)#ip address 17.57.199,.    00.2 255.255.255.o0  0 ^ % Invalid input detected at '^' marker. S6(config-if)#no swi S6(config-if)#no switchport S6(config-if)#no switchport ip address 17.57.100.2 255.255.255.0 S6(config-if)#^Z S6# 06:05:57: %SYS-5-CONFIG_I: Configured from console by console S6# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Ethernet0/1 unassigned YES unset administratively down down Serial0/1 unassigned YES unset administratively down down R1#confi gt ^ % Invalid input detected at '^' marker. R1#conbfig t       nfig t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int Ethernet0/1 R1(config-if)#ip address 17.1 57.100.1 255.2155   55.255.0 R1(config-if)#no shut R1(config-if)#^Z R1# *Mar 1 06:04:50.071: %SYS-5-CONFIG_I: Configured from console by console R1# RACK13AS>s 2 [Resuming connection 2 to r2 ... ] *Ma R2#ping 208.28./ 1/ .130 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: ..!!! Success rate is 60 percent (3/5), round-trip min/avg/max = 1/2/4 ms R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#ping 208.28.1.65 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: ..!!! Success rate is 60 percent (3/5), round-trip min/avg/max = 1/3/4 ms R1#ping 208.28.        17.57.100.2 Translating "ping17.57.100.2" Translating "ping17.57.100.2" % Unknown command or computer name, or unable to find computer address R1#ping17.57.100.2ng 17.57.100.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: ..!!! Success rate is 60 percent (3/5), round-trip min/avg/max = 1/2/4 ms R1# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#sh    sh run Building configuration... Current configuration : 2381 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname S5 ! ! no aaa new-model ip subnet-zero no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst --More--  spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport access vlan 10 switchport mode access ! interface FastEthernet0/2 switchport mode dynamic desirable shutdown ! interface FastEthernet0/3 switchport access vlan 34 switchport mode access ! interface FastEthernet0/4 switchport mode dynamic desirable shutdown ! interface FastEthernet0/5 switchport mode dynamic desirable --More--  ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 switchport mode dynamic desirable ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 --More--   switchport mode dynamic desirable ! interface FastEthernet0/14 switchport mode dynamic desirable ! interface FastEthernet0/15 switchport mode dynamic desirable ! interface FastEthernet0/16 switchport mode dynamic desirable ! interface FastEthernet0/17 switchport mode dynamic desirable ! interface FastEthernet0/18 switchport mode dynamic desirable ! interface FastEthernet0/19 switchport mode dynamic desirable ! interface FastEthernet0/20 switchport mode dynamic desirable ! --More--  interface FastEthernet0/21 switchport mode dynamic desirable ! interface FastEthernet0/22 switchport mode dynamic desirable ! interface FastEthernet0/23 switchport mode dynamic desirable ! interface FastEthernet0/24 switchport mode dynamic desirable ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address shutdown ! interface Vlan10 --More--   ip address 208.28.1.65 255.255.255.240 ! interface Vlan20 ip address 208.28.1.130 255.255.255.224 ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 no login line vty 5 15 no login ! ! --More--  end S5# S5# RACK13AS>6 [Resuming connection 6 to r6 ... ] 06:0 S6#sh run | b int vlan internal allocation policy ascending ! ! interface FastEthernet0/1 no switchport ip address 17.57.100.2 255.255.255.0 ! interface FastEthernet0/2 switchport access vlan 20 switchport mode access ! interface FastEthernet0/3 switchport mode dynamic desirable shutdown ! interface FastEthernet0/4 switchport access vlan 34 switchport mode access ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 --More--   switchport mode dynamic desirable ! interface FastEthernet0/7 switchport mode dynamic desirable ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable ! --More--   S6#vlan data % Warning: It is recommended to configure VLAN from config mode, as VLAN database mode is being deprecated. Please consult user documentation for configuring VTP/VLAN in config mode. S6(vlan)#sh cur VLAN ISL Id: 1 Name: default Media Type: Ethernet VLAN 802.10 Id: 100001 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 10 Name: ToR1 Media Type: Ethernet VLAN 802.10 Id: 100010 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 20 Name: ToR2 Media Type: Ethernet VLAN 802.10 Id: 100020 State: Operational --More--   MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 34 Name: BlueSuede Media Type: Ethernet VLAN 802.10 Id: 100034 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 1002 Name: fddi-default Media Type: FDDI VLAN 802.10 Id: 101002 State: Operational MTU: 1500 Bridge Type: SRB Backup CRF Mode: Disabled Remote SPAN VLAN: No --More--   S6(vlan)#^Z S6#sh 06:10:13: %SYS-5-CONFIG_I: Configured from console by console S6#sh vtp status VTP Version : 2 Configuration Revision : 4 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x2D 0x91 0x18 0x58 0x14 0x02 0x34 0xF5 Configuration last modified by 0.0.0.0 at 3-1-93 06:00:24 Local updater ID is 17.57.100.2 on interface Fa0/1 (first layer3 interface found) S6# S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/24 S6(config-if)#swm  S6(config-if)#switchport mocde tr r S6(config-if)#switchport mocde tr ^ % Invalid input detected at '^' marker. S6(config-if)#switchport mocde trde tr  Command rejected: An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode. S6(config-if)# S6(config-if)# S6(config-if)# S6(config-if)#sw S6(config-if)#switchport tr S6(config-if)#switchport trunk en S6(config-if)#switchport trunk encapsulation do S6(config-if)#switchport trunk encapsulation dot1q S6(config-if)# 06:12:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down S6(config-if)# 06:12:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up S6(config-if)#sw S6(config-if)#switchport tr S6(config-if)#switchport trunk > ? allowed Set allowed VLAN characteristics when interface is in trunking mode encapsulation Set trunking encapsulation when interface is in trunking mode native Set trunking native characteristics when interface is in trunking mode pruning Set pruning VLAN characteristics when interface is in trunking mode S6(config-if)#switchport trunk all S6(config-if)#switchport trunk allowed ? vlan Set allowed VLANs when interface is in trunking mode S6(config-if)#switchport trunk allowed vlan ? WORD VLAN IDs of the allowed VLANs when this port is in trunking mode add add VLANs to the current list all all VLANs except all VLANs except the following none no VLANs remove remove VLANs from the current list S6(config-if)#switchport trunk allowed vlan 10,20,34 S6(config-if)#^Z S6#sh 06:13:25: %SYS-5-CONFIG_I: Configured from console by console S6#sh vl  int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable 802.1q trunking 1 Port Vlans allowed on trunk Fa0/24 10,20,34 Port Vlans allowed and active in management domain Fa0/24 10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 10,20,34 S6#vlan    sh lv  vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/3, Fa0/5, Fa0/6, Fa0/7 Fa0/8, Fa0/9, Fa0/10, Fa0/11 Fa0/12, Fa0/13, Fa0/14, Fa0/15 Fa0/16, Fa0/17, Fa0/18, Fa0/19 Fa0/20, Fa0/21, Fa0/22, Fa0/23 Gi0/1, Gi0/2 10 ToR1 active 20 ToR2 active Fa0/2 34 BlueSuede active Fa0/4 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 34 enet 100034 1500 - - - - - 0 0 --More--   S6#cp  config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#vlan 99 S6(config-vlan)#^Z S6# RACK13AS>5 [Resuming connection 5 to r5 ... ] 06:1 S5#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/2, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Gi0/1, Gi0/2 10 ToR1 active Fa0/1 20 ToR2 active 34 BlueSuede active Fa0/3 99 VLAN0099 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 --More--   S5#conbfi    nfig t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#itn fa 0/24 ^ % Invalid input detected at '^' marker. S5(config)#itn fa 0/24n fa 0/24 nt fa 0/24 S5(config-if)#sq S5(config-if)#sq w S5(config-if)#switchport tru S5(config-if)#switchport trunk en S5(config-if)#switchport trunk encapsulation do S5(config-if)#switchport trunk encapsulation dot1q S5(config-if)#sw S5(config-if)#switchport tru S5(config-if)#switchport trunk all S5(config-if)#switchport trunk allowed vl S5(config-if)#switchport trunk allowed vlan 10,20,34 S5(config-if)#sw S5(config-if)#switchport mo S5(config-if)#switchport mode tru S5(config-if)#switchport mode trunk S5(config-if)#^Z S5#c 06:16:12: %SYS-5-CONFIG_I: Configured from console by console S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#no vlan 99 S5(config)#^Z S5# 06:16:19: %SYS-5-CONFIG_I: Configured from console by console S5#sh run int fa 0/24 Building configuration... Current configuration : 135 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport trunk allowed vlan 10,20,34 switchport mode trunk end S5# RACK13AS>6 [Resuming connection 6 to r6 ... ] 06:1 S6#sh run int fa 0/24 Building configuration... Current configuration : 147 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport trunk allowed vlan 10,20,34 switchport mode dynamic desirable end S6# S6#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/3, Fa0/5, Fa0/6, Fa0/7 Fa0/8, Fa0/9, Fa0/10, Fa0/11 Fa0/12, Fa0/13, Fa0/14, Fa0/15 Fa0/16, Fa0/17, Fa0/18, Fa0/19 Fa0/20, Fa0/21, Fa0/22, Fa0/23 Gi0/1, Gi0/2 10 ToR1 active 20 ToR2 active Fa0/2 34 BlueSuede active Fa0/4 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 34 enet 100034 1500 - - - - - 0 0 --More--   S6# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh run int s 1 0/0.1 Building configuration... Current configuration : 118 bytes ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 end R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s 1/0.1 Building configuration... Current configuration : 111 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay interface-dlci 203 end R2#sh fram pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 1 0 0 0 Switched 0 0 0 0 Unused 1 1 0 0 DLCI = 201, DLCI USAGE = UNUSED, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 06:14:23, last time pvc status changed 06:14:03 --More--   DLCI = 203, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.1 input pkts 662 output pkts 15 in bytes 33896 out bytes 510 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 15 out bcast bytes 510 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 06:14:36, last time pvc status changed 06:14:23 --More--   DLCI = 207, DLCI USAGE = UNUSED, PVC STATUS = INACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 06:14:36, last time pvc status changed 06:14:36 R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa    s 1/0.1 R2(config-subif)#int s 1/0.1  \ ^ % Invalid input detected at '^' marker. R2(config)#int s 1/0\  R2(config-if)#do sh fram map Serial1/0.1 (up): ip 208.28.1.2 dlci 203(0xCB,0x30B0), dynamic, broadcast,, status defined, active R2(config-if)#no fram inv R2(config-if)#no fram inverse-arp R2(config-if)#no fram inverse-arp do sh fram map  Serial1/0.1 (up): ip 208.28.1.2 dlci 203(0xCB,0x30B0), dynamic, broadcast,, status defined, active R2(config-if)#int s 1/0.1 R2(config-subif)#no frame-relay interface-dlci 203 R2(config-subif)#fram map R2(config-subif)#fram map ip 208.28.1.2 203 br R2(config-subif)#fram map ip 208.28.1.2 203 broadcast R2(config-subif)#^Z R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh run int s 1/0 Building configuration... Current configuration : 126 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue end R3#\ sh ip  fram map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3# RACK13AS>r7 Translating "r7" Trying R7 (1.1.1.1, 2007)... Open ! ************************************************************** Global Knowledge Hands-On Labs Access Server Access is restricted to Global Knowledge CCIE Students ************************************************************** Please re-enter your password. (This is the same password you used to log onto the Lab website.) If you see a username prompt, please wait 40 seconds and try again. If the username prompt persists, please reset equipment from your "Pod x" link. User Access Verification Password: Password OK Router>en Router#i config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa    s 1/0 Router(config-if)#enca fram Router(config-if)#ip add 1.1.1.1 255.255.2~255                     7.7.7.7 255.255.255.0 Router(config-if)#no shut Router(config-if)#^Z Router# *Mar 1 06:25:09.878: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 06:25:11.024: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh fram map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#sh fram map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#sh fram map     pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 3 0 0 0 Switched 0 0 0 0 Unused 0 0 0 0 DLCI = 301, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 1412 output pkts 767 in bytes 189425 out bytes 40056 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 662 out bcast bytes 33896 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 06:24:38, last time pvc status changed 06:24:18 --More--   DLCI = 302, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 32 output pkts 648 in bytes 1088 out bytes 33420 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 648 out bcast bytes 33420 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 06:24:40, last time pvc status changed 06:24:20 --More--   DLCI = 307, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 1 output pkts 1 in bytes 34 out bytes 34 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1 out bcast bytes 34 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 06:24:42, last time pvc status changed 00:00:11 R3#sh fram pvcmap Serial1/0 (up): ip 7.7.7.7 dlci 307(0x133,0x4C30), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1.9  /0 R3(config-if)#n  o fram inv R3(config-if)#no fram inverse-arp R3(config-if)#fram map ip a 208.28.1.1 301 bri  R3(config-if)#fram map ip 208.28.1.1 301 br br 2 br 302 br 3 302 br R3(config-if)#^Z R3#config tsh fram map *Mar 1 06:27:33.309: %SYS-5-CONFIG_I: Configured from console by console R3#sh fram map Serial1/0 (up): ip 7.7.7.7 dlci 307(0x133,0x4C30), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), static, broadcast, CISCO, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), static, broadcast, CISCO, status defined, active R3#clea fram map ^ % Invalid input detected at '^' marker. R3#clea fram map\      R3#clea frame-relay ? counter Clear Frame Relay counters inarp Clear inverse ARP entries from the map table R3#clea frame-relay in R3#clea frame-relay inarp ? interface Frame Relay Interface R3#clea frame-relay inarp R3#clea frame-relay inarp  map  ^ % Invalid input detected at '^' marker. R3#clea fram mape-relay inarp  map  ^ % Invalid input detected at '^' marker. R3#clea fram mape-relay inarp  map sh fram map  Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), static, broadcast, CISCO, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), static, broadcast, CISCO, status defined, active R3#sh fram pvd\ c ^ % Invalid input detected at '^' marker. R3#sh fram pvdc  s ^ % Invalid input detected at '^' marker. R3#sh fram pvs c PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 3 0 0 0 Switched 0 0 0 0 Unused 0 0 0 0 DLCI = 301, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 1415 output pkts 767 in bytes 190484 out bytes 40056 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 662 out bcast bytes 33896 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 06:27:37, last time pvc status changed 06:27:17 --More--   DLCI = 302, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 32 output pkts 648 in bytes 1088 out bytes 33420 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 648 out bcast bytes 33420 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 06:27:39, last time pvc status changed 06:27:19 --More--   DLCI = 307, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 1 output pkts 1 in bytes 34 out bytes 34 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1 out bcast bytes 34 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 06:27:40, last time pvc status changed 00:03:09 R3#sh fram pvcsdcmap  Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), static, broadcast, CISCO, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), static, broadcast, CISCO, status defined, active R3#ping 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/61/68 ms R3#ping 208.28.1.1 sh fram map ping 208.28.1.1   3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3#^x   RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#ing     ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: . RACK13AS>2 [Resuming connection 2 to r2 ... ] *M R2#deb ip icp mp ICMP packet debugging is on R2# *Mar 1 06:29:24.600: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2#u   u all All possible debugging has been turned off R2#deb fram pack Frame Relay packet debugging is on R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] ..ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: RACK13AS>2 [Resuming connection 2 to r2 ... ] * R2# *Mar 1 06:29:51.352: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 06:29:51.352: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 06:29:53.355: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 06:29:53.355: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 06:29:55.358: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 06:29:55.358: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 06:29:57.357: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 06:29:57.361: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 06:30:01.829: Serial1/0(i): dlci 207(0x30F1), pkt encaps 0x0300 0x8000 0x0000 0x806 (ARP), datagramsize 34 *Mar 1 06:30:01.833: Serial1/0: frame relay INARP received R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)#int s 1/0.1fram map ip 208.28.1.2 203 broadcast  203 broadcast 1 203 broadcast  R2(config-subif)#^Z R2# *Mar 1 06:30:46.550: %SYS-5-CONFIG_I: Configured from console by console R2# RACK13AS>121 [Resuming connection 1 to r1 ... ] ..ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/1 RACK13AS>2 [Resuming connection 2 to r2 ... ] *Mar04 *Mar 1 06:30:52.880: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 06:30:52.880: Serial1/0.1(o): dlci 203(0x30B1), pkt type 0x800(IP), datagramsize 104 R2# *Mar 1 06:31:01.835: Serial1/0(i): dlci 207(0x30F1), pkt encaps 0x0300 0x8000 0x0000 0x806 (ARP), datagramsize 34 *Mar 1 06:31:01.835: Serial1/0: frame relay INARP received R2#u all All possible debugging has been turned off R2#sh run |     int     | 1/0 ^ % Invalid input detected at '^' marker. R2#sh run | 1/0 b1/0 1/0 interface Serial1/0 no ip address encapsulation frame-relay no fair-queue no frame-relay inverse-arp ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 broadcast frame-relay map ip 208.28.1.2 203 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/0 Building configuration... Current configuration : 244 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.3 302 broadcast no frame-relay inverse-arp end R3# R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] ms R1# R1#ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/126/148 ms R1# R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#deb fram pack Frame Relay packet debugging is on R3#ping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: *Mar 1 06:32:48.698: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 06:32:50.702: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 06:32:52.705: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 06:32:54.704: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 06:32:56.707: Serial1/0:Encaps failed--no map entry link 7(IP). Success rate is 0 percent (0/5) R3#ping      sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 17.80.1.1 YES manual up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 208.28.1.2 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.3 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--   R3#ping 180.40.7.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/60/68 ms R3# *Mar 1 06:33:15.723: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 353 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s1/0 R3(config-if)#int s1/0fram map ip 208.28.1.3 302 br 302 br 2 302 br R3(config-if)#^Z R3#config tping 180.40.7.3 *Mar 1 06:34:08.501: %SYS-5-CONFIG_I: Configured from console by console R3#ping 180.40.7.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3#ping 180.40.7.3config t ping 180.40.7.3sh ip int brie ping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/117/124 ms R3# *Mar 1 06:34:13.581: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:13.629: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 60 *Mar 1 06:34:13.646: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 06:34:13.650: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:13.706: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 06:34:13.706: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:13.766: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 06:34:13.766: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:13.822: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 06:34:13.826: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:13.882: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 06:34:13.882: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:13.938: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 06:34:13.942: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:13.998: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 06:34:13.998: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:14.058: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 06:34:14.058: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:14.114: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 06:34:14.118: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 06:34:14.174: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 R3# R3# *Mar 1 06:34:15.729: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 353 R3#u all All possible debugging has been turned off R3#sh run int s 1/0 Building configuration... Current configuration : 289 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.2 302 broadcast frame-relay map ip 208.28.1.3 302 broadcast no frame-relay inverse-arp end R3# R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#confi gt ^ % Invalid input detected at '^' marker. R1#int   config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#fram map ip 208.28.1.2  1  1o0  03 Only frame-relay interface-dlci command should beused on point-to-point interfaces not frame-relay map R1(config-subif)# R1(config-subif)# R1(config-subif)# R1(config-subif)#^Z R1#config t *Mar 1 06:36:51.893: %SYS-5-CONFIG_I: Configured from console by console R1#config t gtping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/118/136 ms R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#shut R2(config-if)# R2(config-if)# R2(config-if)# *Mar 1 06:37:36.799: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 06:37:37.800: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R2(config-if)#en pp R2(config-if)#exit R2(config)#user Two pass For-The-Show R2(config)#int s 1/2 R2(config-if)#pp authen pap R2(config-if)#ppp pap ? refuse Refuse to authenticate using PAP sent-username Set outbound PAP username wait Wait for caller to authenticate first R2(config-if)#ppp pap se R2(config-if)#ppp pap sent-username Om ne ? password Set outbound PAP password R2(config-if)#ppp pap sent-username One pass For-The-Money R2(config-if)#ppp pap sent-username One pass For-The-Money authen pap  ? WORD Use an authentication list with this name callback Authenticate remote on callback only callin Authenticate remote on incoming call only callout Authenticate remote on outgoing call only chap Challenge Handshake Authentication Protocol (CHAP) default Use the default authentication list eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) one-time Allow use of username*OTP for one-time passwords optional Allow peer to refuse to authenticate R2(config-if)#pp authen pap optional R2(config-if)#do deb ppp ne PPP protocol negotiation debugging is on R2(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#en ppp R3(config-if)#exit R3(config)#user One pass For-The-Money R3(config)#int s 1/2 R3(config-if)# RACK13AS> [Resuming connection 3 to r3 ... ] 2 ^ % Invalid input detected at '^' marker. R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#no shut R2(config-if)# *Mar 1 06:51:40.389: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:51:40.413: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:51:40.437: Se1/2 PPP: Outbound cdp packet dropped R2(config-if)# *Mar 1 06:51:42.369: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 06:51:42.397: Se1/2 PPP: Using default call direction *Mar 1 06:51:42.401: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:51:42.401: Se1/2 PPP: Session handle[AE000000] Session id[1] *Mar 1 06:51:42.401: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:51:42.401: Se1/2 LCP: O CONFREQ [Closed] id 1 len 14 *Mar 1 06:51:42.401: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:51:42.401: Se1/2 LCP: MagicNumber 0x14D9E837 (0x050614D9E837) *Mar 1 06:51:42.405: Se1/2 LCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 06:51:42.405: Se1/2 LCP: MagicNumber 0x14F80205 (0x050614F80205) *Mar 1 06:51:42.405: Se1/2 LCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 06:51:42.405: Se1/2 LCP: MagicNumber 0x14F80205 (0x050614F80205) *Mar 1 06:51:42.409: Se1/2 LCP: I CONFNAK [ACKsent] id 1 len 9 *Mar 1 06:51:42.409: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:51: R2(config-if)#42.413: Se1/2 LCP: O CONFREQ [ACKsent] id 2 len 14 *Mar 1 06:51:42.413: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:51:42.413: Se1/2 LCP: MagicNumber 0x14D9E837 (0x050614D9E837) *Mar 1 06:51:42.421: Se1/2 LCP: I CONFNAK [ACKsent] id 2 len 9 *Mar 1 06:51:42.421: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:51:42.421: Se1/2 LCP: O CONFREQ [ACKsent] id 3 len 14 *Mar 1 06:51:42.421: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:51:42.421: Se1/2 LCP: MagicNumber 0x14D9E837 (0x050614D9E837) *Mar 1 06:51:42.429: Se1/2 LCP: I CONFNAK [ACKsent] id 3 len 9 *Mar 1 06:51:42.429: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:51:42.429: Se1/2 LCP: O CONFREQ [ACKsent] id 4 len 14 *Mar 1 06:51:42.429: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:51:42.429: Se1/2 LCP: MagicNumber 0x14D9E837 (0x050614D9E837) *Mar 1 06:51:42.437: Se1/2 LCP: I CONFNAK [ACKsent] id 4 len 9 *Mar 1 06:51:42.437: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:51:42.441: Se1/2 LCP: O CONFREQ [ACKsent] id 5 len 14 *Mar 1 06:51:42.441: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:51:42.441: Se1/2 LCP: MagicNumber 0x14D9E837 (0x050614D9E837) *Mar 1 06:51:42.453: Se1/2 LCP: I CONFNAK [ACKsent] id 5 len 9 *Mar 1 06:51:42.453: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 06:51:42.453: Se1/2 LCP: O CONFREQ [ACKsent] id 6 len 14 *Mar 1 06:51:42.457: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:51:42.457: Se1/2 LCP: MagicNumber 0x14D9E837 (0x050614D9E837) *Mar 1 06:51:42.465: Se1/2 LCP: I CONFREJ [ACKsent] id 6 len 8 *Mar 1 06:51:42.465: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:51:42.465: Se1/2 LCP: O CONFREQ [ACKsent] id 7 len 10 *Mar 1 06:51:42.465: Se1/2 LCP: MagicNumber 0x14D9E837 (0x050614D9E837) *Mar 1 06:51:42.473: Se1/2 LCP: I CONFACK [ACKsent] id 7 len 10 *Mar 1 06:51:42.473: Se1/2 LCP: MagicNumber 0x14D9E837 (0x050614D9E837) *Mar 1 06:51:42.473: Se1/2 LCP: State is Open *Mar 1 06:51:42.473: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:51:42.473: Se1/2 PPP: Phase is ESTABLISHING, Finish LCP *Mar 1 06:51:42.477: Se1/2 PPP: Phase is UP *Mar 1 06:51:42.477: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 06:51:42.477: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:51:42.477: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 06:51:42.481: Se1/2 PPP: Process pending ncp packets *Mar 1 06:51:42.481: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 06:51:42.481: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 06:51:42.481: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 06:51:42.481: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:51:42.481: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 06:51:42.481: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:51:42.485: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 06:51:42.485: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:51:42.485: Se1/2 IPCP: State is Open *Mar 1 06:51:42.485: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 06:51:42.489: Se1/2 CDPCP: State is Open *Mar 1 06:51:42.489: Se1/2 IPCP: Install route to 180.40.7.3 *Mar 1 06:51:42.493: Se1/2 IPCP: Add link info for cef entry 180.40.7.3 *Mar 1 06:51:43.474: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2(config-if)# R2(config-if)#do pin 1`8   180.40.7.4 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms R2(config-if)#shut R2(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 06 R3(config-if)# *Mar 1 06:53:08.898: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down *Mar 1 06:53:09.900: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#en    ppp authen pap oth  R3(config-if)#ppp authen pap ot p R3(config-if)#ppp authen pap optional R3(config-if)#ppp a pap sw ent Two pass cisco R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Ma R2(config-if)#no shut R2(config-if)# *Mar 1 06:54:03.428: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:54:03.452: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:54:03.476: Se1/2 PPP: Outbound cdp packet dropped R2(config-if)# *Mar 1 06:54:05.399: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 06:54:05.399: Se1/2 PPP: Using default call direction *Mar 1 06:54:05.399: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:54:05.399: Se1/2 PPP: Session handle[92000001] Session id[2] *Mar 1 06:54:05.399: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:54:05.399: Se1/2 LCP: O CONFREQ [Closed] id 8 len 14 *Mar 1 06:54:05.399: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:05.403: Se1/2 LCP: MagicNumber 0x14DC16CF (0x050614DC16CF) *Mar 1 06:54:05.411: Se1/2 LCP: I CONFREQ [REQsent] id 2 len 14 *Mar 1 06:54:05.411: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:05.411: Se1/2 LCP: MagicNumber 0x14FA30A4 (0x050614FA30A4) *Mar 1 06:54:05.411: Se1/2 LCP: O CONFACK [REQsent] id 2 len 14 *Mar 1 06:54:05.411: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:05.411: Se1/2 LCP: MagicNumber 0x14FA30A4 (0x050614FA30A4) *Mar 1 06:54:05.4 R2(config-if)#11: Se1/2 LCP: I CONFACK [ACKsent] id 8 len 14 *Mar 1 06:54:05.415: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:05.415: Se1/2 LCP: MagicNumber 0x14DC16CF (0x050614DC16CF) *Mar 1 06:54:05.415: Se1/2 LCP: State is Open *Mar 1 06:54:05.415: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:05.415: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:05.415: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:05.415: Se1/2 PAP: O AUTH-REQ id 1 len 22 from "One" *Mar 1 06:54:05.419: Se1/2 PAP: I AUTH-REQ id 1 len 14 from "Two" *Mar 1 06:54:05.419: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:05.423: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:05.423: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:05.423: Se1/2 PAP: O AUTH-NAK id 1 len 26 msg is "Authentication failed" *Mar 1 06:54:05.427: Se1/2 PPP: Sending Acct Event[Down] id[4] *Mar 1 06:54:05.427: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:05.427: Se1/2 LCP: O TERMREQ [Open] id 9 len 4 *Mar 1 06:54:05.427: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:05.435: Se1/2 LCP: I TERMACK [TERMsent] id 9 len 4 *Mar 1 06:54:05.435: Se1/2 LCP: State is Closed *Mar 1 06:54:05.435: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:05.439: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:05.439: Se1/2 LCP: State is Listen *Mar 1 06:54:07.446: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:07.446: Se1/2 LCP: O CONFREQ [Listen] id 10 len 14 *Mar 1 06:54:07.446: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:07.446: Se1/2 LCP: MagicNumber 0x14DC1ECF (0x050614DC1ECF) *Mar 1 06:54:07.454: Se1/2 LCP: I CONFREQ [REQsent] id 3 len 14 *Mar 1 06:54:07.454: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:07.454: Se1/2 LCP: MagicNumber 0x14FA38A1 (0x050614FA38A1) *Mar 1 06:54:07.458: Se1/2 LCP: O CONFACK [REQsent] id 3 len 14 *Mar 1 06:54:07.458: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:07.458: Se1/2 LCP: MagicNumber 0x14FA38A1 (0x050614FA38A1) *Mar 1 06:54:07.458: Se1/2 LCP: I CONFACK [ACKsent] id 10 len 14 *Mar 1 06:54:07.458: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:07.458: Se1/2 LCP: MagicNumber 0x14DC1ECF (0x050614DC1ECF) *Mar 1 06:54:07.458: Se1/2 LCP: State is Open *Mar 1 06:54:07.463: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:07.463: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:07.463: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:07.463: Se1/2 PAP: O AUTH-REQ id 2 len 22 from "One" *Mar 1 06:54:07.467: Se1/2 PAP: I AUTH-REQ id 2 len 14 from "Two" *Mar 1 06:54:07.467: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:07.467: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:07.467: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:07.471: Se1/2 PAP: O AUTH-NAK id 2 len 26 msg is "Authentication failed" *Mar 1 06:54:07.471: Se1/2 PPP: Sending Acct Event[Down] id[5] *Mar 1 06:54:07.475: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:07.475: Se1/2 LCP: O TERMREQ [Open] id 11 len 4 *Mar 1 06:54:07.475: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:07.479: Se1/2 LCP: I TERMACK [TERMsent] id 11 len 4 *Mar 1 06:54:07.479: Se1/2 LCP: State is Closed *Mar 1 06:54:07.483: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:07.483: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:07.483: Se1/2 LCP: State is Listen *Mar 1 06:54:09.494: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:09.494: Se1/2 LCP: O CONFREQ [Listen] id 12 len 14 *Mar 1 06:54:09.494: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:09.494: Se1/2 LCP: MagicNumber 0x14DC26CF (0x050614DC26CF) *Mar 1 06:54:09.502: Se1/2 LCP: I CONFREQ [REQsent] id 4 len 14 *Mar 1 06:54:09.502: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:09.502: Se1/2 LCP: MagicNumber 0x14FA40A5 (0x050614FA40A5) *Mar 1 06:54:09.506: Se1/2 LCP: O CONFACK [REQsent] id 4 len 14 *Mar 1 06:54:09.506: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:09.506: Se1/2 LCP: MagicNumber 0x14FA40A5 (0x050614FA40A5) *Mar 1 06:54:09.506: Se1/2 LCP: I CONFACK [ACKsent] id 12 len 14 *Mar 1 06:54:09.506: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:09.506: Se1/2 LCP: MagicNumber 0x14DC26CF (0x050614DC26CF) *Mar 1 06:54:09.506: Se1/2 LCP: State is Open *Mar 1 06:54:09.510: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:09.510: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:09.510: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:09.510: Se1/2 PAP: O AUTH-REQ id 3 len 22 from "One" *Mar 1 06:54:09.514: Se1/2 PAP: I AUTH-REQ id 3 len 14 from "Two" *Mar 1 06:54:09.514: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:09.514: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:09.514: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:09.518: Se1/2 PAP: O AUTH-NAK id 3 len 26 msg is "Authentication failed" *Mar 1 06:54:09.518: Se1/2 PPP: Sending Acct Event[Down] id[6] *Mar 1 06:54:09.522: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:09.522: Se1/2 LCP: O TERMREQ [Open] id 13 len 4 *Mar 1 06:54:09.522: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:09.526: Se1/2 LCP: I TERMACK [TERMsent] id 13 len 4 *Mar 1 06:54:09.526: Se1/2 LCP: State is Closed *Mar 1 06:54:09.530: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:09.530: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:09.530: Se1/2 LCP: State is Listen *Mar 1 06:54:11.541: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:11.541: Se1/2 LCP: O CONFREQ [Listen] id 14 len 14 *Mar 1 06:54:11.541: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:11.541: Se1/2 LCP: MagicNumber 0x14DC2ED0 (0x050614DC2ED0) *Mar 1 06:54:11.549: Se1/2 LCP: I CONFREQ [REQsent] id 5 len 14 *Mar 1 06:54:11.549: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:11.549: Se1/2 LCP: MagicNumber 0x14FA48A5 (0x050614FA48A5) *Mar 1 06:54:11.553: Se1/2 LCP: O CONFACK [REQsent] id 5 len 14 *Mar 1 06:54:11.553: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:11.553: Se1/2 LCP: MagicNumber 0x14FA48A5 (0x050614FA48A5) *Mar 1 06:54:11.553: Se1/2 LCP: I CONFACK [ACKsent] id 14 len 14 *Mar 1 06:54:11.553: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:11.553: Se1/2 LCP: MagicNumber 0x14DC2ED0 (0x050614DC2ED0) *Mar 1 06:54:11.553: Se1/2 LCP: State is Open *Mar 1 06:54:11.557: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:11.557: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:11.557: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:11.557: Se1/2 PAP: O AUTH-REQ id 4 len 22 from "One" *Mar 1 06:54:11.561: Se1/2 PAP: I AUTH-REQ id 4 len 14 from "Two" *Mar 1 06:54:11.561: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:11.561: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:11.561: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:11.565: Se1/2 PAP: O AUTH-NAK id 4 len 26 msg is "Authentication failed" *Mar 1 06:54:11.565: Se1/2 PPP: Sending Acct Event[Down] id[7] *Mar 1 06:54:11.569: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:11.569: Se1/2 LCP: O TERMREQ [Open] id 15 len 4 *Mar 1 06:54:11.569: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:11.573: Se1/2 LCP: I TERMACK [TERMsent] id 15 len 4 *Mar 1 06:54:11.573: Se1/2 LCP: State is Closed *Mar 1 06:54:11.577: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:11.577: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:11.577: Se1/2 LCP: State is Listen *Mar 1 06:54:13.593: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:13.593: Se1/2 LCP: O CONFREQ [Listen] id 16 len 14 *Mar 1 06:54:13.593: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:13.593: Se1/2 LCP: MagicNumber 0x14DC36D4 (0x050614DC36D4) *Mar 1 06:54:13.601: Se1/2 LCP: I CONFREQ [REQsent] id 6 len 14 *Mar 1 06:54:13.601: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:13.601: Se1/2 LCP: MagicNumber 0x14FA50AA (0x050614FA50AA) *Mar 1 06:54:13.605: Se1/2 LCP: O CONFACK [REQsent] id 6 len 14 *Mar 1 06:54:13.605: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:13.605: Se1/2 LCP: MagicNumber 0x14FA50AA (0x050614FA50AA) *Mar 1 06:54:13.605: Se1/2 LCP: I CONFACK [ACKsent] id 16 len 14 *Mar 1 06:54:13.605: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:13.605: Se1/2 LCP: MagicNumber 0x14DC36D4 (0x050614DC36D4) *Mar 1 06:54:13.605: Se1/2 LCP: State is Open *Mar 1 06:54:13.609: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:13.609: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:13.609: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:13.609: Se1/2 PAP: O AUTH-REQ id 5 len 22 from "One" *Mar 1 06:54:13.613: Se1/2 PAP: I AUTH-REQ id 5 len 14 from "Two" *Mar 1 06:54:13.613: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:13.613: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:13.613: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:13.617: Se1/2 PAP: O AUTH-NAK id 5 len 26 msg is "Authentication failed" *Mar 1 06:54:13.617: Se1/2 PPP: Sending Acct Event[Down] id[8] *Mar 1 06:54:13.621: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:13.621: Se1/2 LCP: O TERMREQ [Open] id 17 len 4 *Mar 1 06:54:13.621: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:13.629: Se1/2 LCP: I TERMACK [TERMsent] id 17 len 4 *Mar 1 06:54:13.629: Se1/2 LCP: State is Closed *Mar 1 06:54:13.629: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:13.629: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:13.629: Se1/2 LCP: State is Listen *Mar 1 06:54:15.640: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:15.640: Se1/2 LCP: O CONFREQ [Listen] id 18 len 14 *Mar 1 06:54:15.640: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:15.640: Se1/2 LCP: MagicNumber 0x14DC3ED4 (0x050614DC3ED4) *Mar 1 06:54:15.648: Se1/2 LCP: I CONFREQ [REQsent] id 7 len 14 *Mar 1 06:54:15.648: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:15.648: Se1/2 LCP: MagicNumber 0x14FA58AA (0x050614FA58AA) *Mar 1 06:54:15.652: Se1/2 LCP: O CONFACK [REQsent] id 7 len 14 *Mar 1 06:54:15.652: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:15.652: Se1/2 LCP: MagicNumber 0x14FA58AA (0x050614FA58AA) *Mar 1 06:54:15.652: Se1/2 LCP: I CONFACK [ACKsent] id 18 len 14 *Mar 1 06:54:15.652: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:15.652: Se1/2 LCP: MagicNumber 0x14DC3ED4 (0x050614DC3ED4) *Mar 1 06:54:15.652: Se1/2 LCP: State is Open *Mar 1 06:54:15.656: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:15.656: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:15.656: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:15.656: Se1/2 PAP: O AUTH-REQ id 6 len 22 from "One" *Mar 1 06:54:15.660: Se1/2 PAP: I AUTH-REQ id 6 len 14 from "Two" *Mar 1 06:54:15.660: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:15.660: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:15.660: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:15.664: Se1/2 PAP: O AUTH-NAK id 6 len 26 msg is "Authentication failed" *Mar 1 06:54:15.664: Se1/2 PPP: Sending Acct Event[Down] id[9] *Mar 1 06:54:15.668: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:15.668: Se1/2 LCP: O TERMREQ [Open] id 19 len 4 *Mar 1 06:54:15.668: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:15.672: Se1/2 LCP: I TERMACK [TERMsent] id 19 len 4 *Mar 1 06:54:15.676: Se1/2 LCP: State is Closed *Mar 1 06:54:15.676: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:15.676: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:15.676: Se1/2 LCP: State is Listen *Mar 1 06:54:17.687: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:17.687: Se1/2 LCP: O CONFREQ [Listen] id 20 len 14 *Mar 1 06:54:17.687: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:17.687: Se1/2 LCP: MagicNumber 0x14DC46D5 (0x050614DC46D5) *Mar 1 06:54:17.695: Se1/2 LCP: I CONFREQ [REQsent] id 8 len 14 *Mar 1 06:54:17.695: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:17.695: Se1/2 LCP: MagicNumber 0x14FA60A7 (0x050614FA60A7) *Mar 1 06:54:17.699: Se1/2 LCP: O CONFACK [REQsent] id 8 len 14 *Mar 1 06:54:17.699: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:17.699: Se1/2 LCP: MagicNumber 0x14FA60A7 (0x050614FA60A7) *Mar 1 06:54:17.699: Se1/2 LCP: I CONFACK [ACKsent] id 20 len 14 *Mar 1 06:54:17.699: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:17.699: Se1/2 LCP: MagicNumber 0x14DC46D5 (0x050614DC46D5) *Mar 1 06:54:17.699: Se1/2 LCP: State is Open *Mar 1 06:54:17.703: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:17.703: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:17.703: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:17.703: Se1/2 PAP: O AUTH-REQ id 7 len 22 from "One" *Mar 1 06:54:17.707: Se1/2 PAP: I AUTH-REQ id 7 len 14 from "Two" *Mar 1 06:54:17.707: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:17.707: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:17.707: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:17.711: Se1/2 PAP: O AUTH-NAK id 7 len 26 msg is "Authentication failed" *Mar 1 06:54:17.711: Se1/2 PPP: Sending Acct Event[Down] id[A] *Mar 1 06:54:17.715: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:17.715: Se1/2 LCP: O TERMREQ [Open] id 21 len 4 *Mar 1 06:54:17.715: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:17.719: Se1/2 LCP: I TERMACK [TERMsent] id 21 len 4 *Mar 1 06:54:17.719: Se1/2 LCP: State is Closed *Mar 1 06:54:17.723: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:17.723: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:17.723: Se1/2 LCP: State is Listen *Mar 1 06:54:19.735: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:19.735: Se1/2 LCP: O CONFREQ [Listen] id 22 len 14 *Mar 1 06:54:19.735: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:19.735: Se1/2 LCP: MagicNumber 0x14DC4ED5 (0x050614DC4ED5) *Mar 1 06:54:19.743: Se1/2 LCP: I CONFREQ [REQsent] id 9 len 14 *Mar 1 06:54:19.743: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:19.743: Se1/2 LCP: MagicNumber 0x14FA68A7 (0x050614FA68A7) *Mar 1 06:54:19.747: Se1/2 LCP: O CONFACK [REQsent] id 9 len 14 *Mar 1 06:54:19.747: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:19.747: Se1/2 LCP: MagicNumber 0x14FA68A7 (0x050614FA68A7) *Mar 1 06:54:19.747: Se1/2 LCP: I CONFACK [ACKsent] id 22 len 14 *Mar 1 06:54:19.747: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:19.747: Se1/2 LCP: MagicNumber 0x14DC4ED5 (0x050614DC4ED5) *Mar 1 06:54:19.747: Se1/2 LCP: State is Open *Mar 1 06:54:19.751: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:19.751: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:19.751: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:19.751: Se1/2 PAP: O AUTH-REQ id 8 len 22 from "One" *Mar 1 06:54:19.755: Se1/2 PAP: I AUTH-REQ id 8 len 14 from "Two" *Mar 1 06:54:19.755: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:19.755: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:19.755: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:19.759: Se1/2 PAP: O AUTH-NAK id 8 len 26 msg is "Authentication failed" *Mar 1 06:54:19.759: Se1/2 PPP: Sending Acct Event[Down] id[B] *Mar 1 06:54:19.763: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:19.763: Se1/2 LCP: O TERMREQ [Open] id 23 len 4 *Mar 1 06:54:19.763: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:19.767: Se1/2 LCP: I TERMACK [TERMsent] id 23 len 4 *Mar 1 06:54:19.767: Se1/2 LCP: State is Closed *Mar 1 06:54:19.771: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:19.771: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:19.771: Se1/2 LCP: State is Listen *Mar 1 06:54:21.782: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:21.782: Se1/2 LCP: O CONFREQ [Listen] id 24 len 14 *Mar 1 06:54:21.782: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:21.782: Se1/2 LCP: MagicNumber 0x14DC56D6 (0x050614DC56D6) *Mar 1 06:54:21.790: Se1/2 LCP: I CONFREQ [REQsent] id 10 len 14 *Mar 1 06:54:21.790: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:21.790: Se1/2 LCP: MagicNumber 0x14FA70AB (0x050614FA70AB) *Mar 1 06:54:21.794: Se1/2 LCP: O CONFACK [REQsent] id 10 len 14 *Mar 1 06:54:21.794: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:21.794: Se1/2 LCP: MagicNumber 0x14FA70AB (0x050614FA70AB) *Mar 1 06:54:21.794: Se1/2 LCP: I CONFACK [ACKsent] id 24 len 14 *Mar 1 06:54:21.794: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:21.794: Se1/2 LCP: MagicNumber 0x14DC56D6 (0x050614DC56D6) *Mar 1 06:54:21.794: Se1/2 LCP: State is Open *Mar 1 06:54:21.798: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:21.798: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:21.798: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:21.798: Se1/2 PAP: O AUTH-REQ id 9 len 22 from "One" *Mar 1 06:54:21.802: Se1/2 PAP: I AUTH-REQ id 9 len 14 from "Two" *Mar 1 06:54:21.802: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:21.802: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:21.802: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:21.806: Se1/2 PAP: O AUTH-NAK id 9 len 26 msg is "Authentication failed" *Mar 1 06:54:21.806: Se1/2 PPP: Sending Acct Event[Down] id[C] *Mar 1 06:54:21.810: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:21.810: Se1/2 LCP: O TERMREQ [Open] id 25 len 4 *Mar 1 06:54:21.810: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:21.814: Se1/2 LCP: I TERMACK [TERMsent] id 25 len 4 *Mar 1 06:54:21.818: Se1/2 LCP: State is Closed *Mar 1 06:54:21.818: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:21.818: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:21.818: Se1/2 LCP: State is Listen *Mar 1 06:54:23.829: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:23.829: Se1/2 LCP: O CONFREQ [Listen] id 26 len 14 *Mar 1 06:54:23.829: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:23.829: Se1/2 LCP: MagicNumber 0x14DC5ED6 (0x050614DC5ED6) *Mar 1 06:54:23.837: Se1/2 LCP: I CONFREQ [REQsent] id 11 len 14 *Mar 1 06:54:23.837: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:23.837: Se1/2 LCP: MagicNumber 0x14FA78A8 (0x050614FA78A8) *Mar 1 06:54:23.841: Se1/2 LCP: O CONFACK [REQsent] id 11 len 14 *Mar 1 06:54:23.841: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:23.841: Se1/2 LCP: MagicNumber 0x14FA78A8 (0x050614FA78A8) *Mar 1 06:54:23.841: Se1/2 LCP: I CONFACK [ACKsent] id 26 len 14 *Mar 1 06:54:23.841: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:23.841: Se1/2 LCP: MagicNumber 0x14DC5ED6 (0x050614DC5ED6) *Mar 1 06:54:23.841: Se1/2 LCP: State is Open *Mar 1 06:54:23.845: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:23.845: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:23.845: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:23.845: Se1/2 PAP: O AUTH-REQ id 10 len 22 from "One" *Mar 1 06:54:23.849: Se1/2 PAP: I AUTH-REQ id 10 len 14 from "Two" *Mar 1 06:54:23.849: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:23.849: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:23.849: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:23.853: Se1/2 PAP: O AUTH-NAK id 10 len 26 msg is "Authentication failed" *Mar 1 06:54:23.853: Se1/2 PPP: Sending Acct Event[Down] id[D] *Mar 1 06:54:23.853: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:23.857: Se1/2 LCP: O TERMREQ [Open] id 27 len 4 *Mar 1 06:54:23.857: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:23.861: Se1/2 LCP: I TERMACK [TERMsent] id 27 len 4 *Mar 1 06:54:23.861: Se1/2 LCP: State is Closed *Mar 1 06:54:23.865: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:23.865: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:23.865: Se1/2 LCP: State is Listen *Mar 1 06:54:25.881: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:25.881: Se1/2 LCP: O CONFREQ [Listen] id 28 len 14 *Mar 1 06:54:25.881: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:25.881: Se1/2 LCP: MagicNumber 0x14DC66DA (0x050614DC66DA) *Mar 1 06:54:25.889: Se1/2 LCP: I CONFREQ [REQsent] id 12 len 14 *Mar 1 06:54:25.889: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:25.889: Se1/2 LCP: MagicNumber 0x14FA80B0 (0x050614FA80B0) *Mar 1 06:54:25.893: Se1/2 LCP: O CONFACK [REQsent] id 12 len 14 *Mar 1 06:54:25.893: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:25.893: Se1/2 LCP: MagicNumber 0x14FA80B0 (0x050614FA80B0) *Mar 1 06:54:25.893: Se1/2 LCP: I CONFACK [ACKsent] id 28 len 14 *Mar 1 06:54:25.893: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:25.893: Se1/2 LCP: MagicNumber 0x14DC66DA (0x050614DC66DA) *Mar 1 06:54:25.893: Se1/2 LCP: State is Open *Mar 1 06:54:25.897: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:25.897: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:25.897: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:25.897: Se1/2 PAP: O AUTH-REQ id 11 len 22 from "One" *Mar 1 06:54:25.901: Se1/2 PAP: I AUTH-REQ id 11 len 14 from "Two" *Mar 1 06:54:25.901: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:25.901: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:25.901: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:25.905: Se1/2 PAP: O AUTH-NAK id 11 len 26 msg is "Authentication failed" *Mar 1 06:54:25.905: Se1/2 PPP: Sending Acct Event[Down] id[E] *Mar 1 06:54:25.909: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:25.909: Se1/2 LCP: O TERMREQ [Open] id 29 len 4 *Mar 1 06:54:25.909: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:25.921: Se1/2 LCP: I TERMACK [TERMsent] id 29 len 4 *Mar 1 06:54:25.921: Se1/2 LCP: State is Closed *Mar 1 06:54:25.921: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:25.925: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:25.925: Se1/2 LCP: State is Listen *Mar 1 06:54:27.928: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:27.928: Se1/2 LCP: O CONFREQ [Listen] id 30 len 14 *Mar 1 06:54:27.928: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:27.928: Se1/2 LCP: MagicNumber 0x14DC6EDB (0x050614DC6EDB) *Mar 1 06:54:27.940: Se1/2 LCP: I CONFREQ [REQsent] id 13 len 14 *Mar 1 06:54:27.940: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:27.940: Se1/2 LCP: MagicNumber 0x14FA88B0 (0x050614FA88B0) *Mar 1 06:54:27.940: Se1/2 LCP: O CONFACK [REQsent] id 13 len 14 *Mar 1 06:54:27.940: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:27.940: Se1/2 LCP: MagicNumber 0x14FA88B0 (0x050614FA88B0) *Mar 1 06:54:27.944: Se1/2 LCP: I CONFACK [ACKsent] id 30 len 14 *Mar 1 06:54:27.944: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:27.944: Se1/2 LCP: MagicNumber 0x14DC6EDB (0x050614DC6EDB) *Mar 1 06:54:27.944: Se1/2 LCP: State is Open *Mar 1 06:54:27.944: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:27.944: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:27.944: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:27.944: Se1/2 PAP: O AUTH-REQ id 12 len 22 from "One" *Mar 1 06:54:27.952: Se1/2 PAP: I AUTH-REQ id 12 len 14 from "Two" *Mar 1 06:54:27.952: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:27.952: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:27.952: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:27.956: Se1/2 PAP: O AUTH-NAK id 12 len 26 msg is "Authentication failed" *Mar 1 06:54:27.956: Se1/2 PPP: Sending Acct Event[Down] id[F] *Mar 1 06:54:27.956: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:27.956: Se1/2 LCP: O TERMREQ [Open] id 31 len 4 *Mar 1 06:54:27.960: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:27.964: Se1/2 LCP: I TERMACK [TERMsent] id 31 len 4 *Mar 1 06:54:27.964: Se1/2 LCP: State is Closed *Mar 1 06:54:27.964: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:27.968: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:27.968: Se1/2 LCP: State is Listen *Mar 1 06:54:29.975: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:29.975: Se1/2 LCP: O CONFREQ [Listen] id 32 len 14 *Mar 1 06:54:29.975: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:29.975: Se1/2 LCP: MagicNumber 0x14DC76DB (0x050614DC76DB) *Mar 1 06:54:31.991: Se1/2 LCP: TIMEout: State REQsent *Mar 1 06:54:31.991: Se1/2 LCP: O CONFREQ [REQsent] id 33 len 14 *Mar 1 06:54:31.991: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:31.991: Se1/2 LCP: MagicNumber 0x14DC76DB (0x050614DC76DB) *Mar 1 06:54:31.999: Se1/2 LCP: I CONFREQ [REQsent] id 14 len 14 *Mar 1 06:54:31.999: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:31.999: Se1/2 LCP: MagicNumber 0x14FA988C (0x050614FA988C) *Mar 1 06:54:32.003: Se1/2 LCP: O CONFACK [REQsent] id 14 len 14 *Mar 1 06:54:32.003: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:32.003: Se1/2 LCP: MagicNumber 0x14FA988C (0x050614FA988C) *Mar 1 06:54:32.003: Se1/2 LCP: I CONFACK [ACKsent] id 33 len 14 *Mar 1 06:54:32.003: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:32.003: Se1/2 LCP: MagicNumber 0x14DC76DB (0x050614DC76DB) *Mar 1 06:54:32.003: Se1/2 LCP: State is Open *Mar 1 06:54:32.003: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:32.007: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:32.007: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:32.007: Se1/2 PAP: O AUTH-REQ id 13 len 22 from "One" *Mar 1 06:54:32.011: Se1/2 PAP: I AUTH-REQ id 13 len 14 from "Two" *Mar 1 06:54:32.011: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:32.011: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:32.011: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:32.015: Se1/2 PAP: O AUTH-NAK id 13 len 26 msg is "Authentication failed" *Mar 1 06:54:32.015: Se1/2 PPP: Sending Acct Event[Down] id[10] *Mar 1 06:54:32.015: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:32.019: Se1/2 LCP: O TERMREQ [Open] id 34 len 4 *Mar 1 06:54:32.019: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:32.023: Se1/2 LCP: I TERMACK [TERMsent] id 34 len 4 *Mar 1 06:54:32.023: Se1/2 LCP: State is Closed *Mar 1 06:54:32.027: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:32.027: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:32.027: Se1/2 LCP: State is Listen *Mar 1 06:54:34.038: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:34.038: Se1/2 LCP: O CONFREQ [Listen] id 35 len 14 *Mar 1 06:54:34.038: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:34.038: Se1/2 LCP: MagicNumber 0x14DC86BB (0x050614DC86BB) *Mar 1 06:54:34.046: Se1/2 LCP: I CONFREQ [REQsent] id 15 len 14 *Mar 1 06:54:34.046: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:34.046: Se1/2 LCP: MagicNumber 0x14FAA090 (0x050614FAA090) *Mar 1 06:54:34.050: Se1/2 LCP: O CONFACK [REQsent] id 15 len 14 *Mar 1 06:54:34.050: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:34.050: Se1/2 LCP: MagicNumber 0x14FAA090 (0x050614FAA090) *Mar 1 06:54:34.050: Se1/2 LCP: I CONFACK [ACKsent] id 35 len 14 *Mar 1 06:54:34.050: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:34.050: Se1/2 LCP: MagicNumber 0x14DC86BB (0x050614DC86BB) *Mar 1 06:54:34.050: Se1/2 LCP: State is Open *Mar 1 06:54:34.054: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:34.054: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:34.054: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:34.054: Se1/2 PAP: O AUTH-REQ id 14 len 22 from "One" *Mar 1 06:54:34.058: Se1/2 PAP: I AUTH-REQ id 14 len 14 from "Two" *Mar 1 06:54:34.058: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:34.058: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:34.058: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:34.062: Se1/2 PAP: O AUTH-NAK id 14 len 26 msg is "Authentication failed" *Mar 1 06:54:34.062: Se1/2 PPP: Sending Acct Event[Down] id[11] *Mar 1 06:54:34.066: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:34.066: Se1/2 LCP: O TERMREQ [Open] id 36 len 4 *Mar 1 06:54:34.066: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:34.070: Se1/2 LCP: I TERMACK [TERMsent] id 36 len 4 *Mar 1 06:54:34.074: Se1/2 LCP: State is Closed *Mar 1 06:54:34.074: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:34.074: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:34.074: Se1/2 LCP: State is Listen *Mar 1 06:54:36.085: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:36.085: Se1/2 LCP: O CONFREQ [Listen] id 37 len 14 *Mar 1 06:54:36.085: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:36.085: Se1/2 LCP: MagicNumber 0x14DC8EBB (0x050614DC8EBB) *Mar 1 06:54:36.093: Se1/2 LCP: I CONFREQ [REQsent] id 16 len 14 *Mar 1 06:54:36.093: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:36.093: Se1/2 LCP: MagicNumber 0x14FAA891 (0x050614FAA891) *Mar 1 06:54:36.097: Se1/2 LCP: O CONFACK [REQsent] id 16 len 14 *Mar 1 06:54:36.097: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:36.097: Se1/2 LCP: MagicNumber 0x14FAA891 (0x050614FAA891) *Mar 1 06:54:36.097: Se1/2 LCP: I CONFACK [ACKsent] id 37 len 14 *Mar 1 06:54:36.097: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:36.097: Se1/2 LCP: MagicNumber 0x14DC8EBB (0x050614DC8EBB) *Mar 1 06:54:36.097: Se1/2 LCP: State is Open *Mar 1 06:54:36.101: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:36.101: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:36.101: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:36.101: Se1/2 PAP: O AUTH-REQ id 15 len 22 from "One" *Mar 1 06:54:36.105: Se1/2 PAP: I AUTH-REQ id 15 len 14 from "Two" *Mar 1 06:54:36.105: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:36.105: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:36.105: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:36.109: Se1/2 PAP: O AUTH-NAK id 15 len 26 msg is "Authentication failed" *Mar 1 06:54:36.109: Se1/2 PPP: Sending Acct Event[Down] id[12] *Mar 1 06:54:36.113: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:36.113: Se1/2 LCP: O TERMREQ [Open] id 38 len 4 *Mar 1 06:54:36.113: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:36.117: Se1/2 LCP: I TERMACK [TERMsent] id 38 len 4 *Mar 1 06:54:36.121: Se1/2 LCP: State is Closed *Mar 1 06:54:36.121: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:36.121: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:36.121: Se1/2 LCP: State is Listen *Mar 1 06:54:38.137: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:38.137: Se1/2 LCP: O CONFREQ [Listen] id 39 len 14 *Mar 1 06:54:38.137: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:38.137: Se1/2 LCP: MagicNumber 0x14DC96BF (0x050614DC96BF) *Mar 1 06:54:38.145: Se1/2 LCP: I CONFREQ [REQsent] id 17 len 14 *Mar 1 06:54:38.145: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:38.145: Se1/2 LCP: MagicNumber 0x14FAB091 (0x050614FAB091) *Mar 1 06:54:38.149: Se1/2 LCP: O CONFACK [REQsent] id 17 len 14 *Mar 1 06:54:38.149: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:38.149: Se1/2 LCP: MagicNumber 0x14FAB091 (0x050614FAB091) *Mar 1 06:54:38.149: Se1/2 LCP: I CONFACK [ACKsent] id 39 len 14 *Mar 1 06:54:38.149: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:38.149: Se1/2 LCP: MagicNumber 0x14DC96BF (0x050614DC96BF) *Mar 1 06:54:38.149: Se1/2 LCP: State is Open *Mar 1 06:54:38.153: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:38.153: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:38.153: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:38.153: Se1/2 PAP: O AUTH-REQ id 16 len 22 from "One" *Mar 1 06:54:38.157: Se1/2 PAP: I AUTH-REQ id 16 len 14 from "Two" *Mar 1 06:54:38.157: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:38.157: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:38.157: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:38.161: Se1/2 PAP: O AUTH-NAK id 16 len 26 msg is "Authentication failed" *Mar 1 06:54:38.161: Se1/2 PPP: Sending Acct Event[Down] id[13] *Mar 1 06:54:38.165: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:38.165: Se1/2 LCP: O TERMREQ [Open] id 40 len 4 *Mar 1 06:54:38.165: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:38.169: Se1/2 LCP: I TERMACK [TERMsent] id 40 len 4 *Mar 1 06:54:38.173: Se1/2 LCP: State is Closed *Mar 1 06:54:38.173: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:38.173: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:38.173: Se1/2 LCP: State is Listen *Mar 1 06:54:40.184: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:40.184: Se1/2 LCP: O CONFREQ [Listen] id 41 len 14 *Mar 1 06:54:40.184: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:40.184: Se1/2 LCP: MagicNumber 0x14DC9EC0 (0x050614DC9EC0) *Mar 1 06:54:40.192: Se1/2 LCP: I CONFREQ [REQsent] id 18 len 14 *Mar 1 06:54:40.192: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:40.192: Se1/2 LCP: MagicNumber 0x14FAB891 (0x050614FAB891) *Mar 1 06:54:40.196: Se1/2 LCP: O CONFACK [REQsent] id 18 len 14 *Mar 1 06:54:40.196: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:40.196: Se1/2 LCP: MagicNumber 0x14FAB891 (0x050614FAB891) *Mar 1 06:54:40.196: Se1/2 LCP: I CONFACK [ACKsent] id 41 len 14 *Mar 1 06:54:40.196: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:40.196: Se1/2 LCP: MagicNumber 0x14DC9EC0 (0x050614DC9EC0) *Mar 1 06:54:40.196: Se1/2 LCP: State is Open *Mar 1 06:54:40.200: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:40.200: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:40.200: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:40.200: Se1/2 PAP: O AUTH-REQ id 17 len 22 from "One" *Mar 1 06:54:40.204: Se1/2 PAP: I AUTH-REQ id 17 len 14 from "Two" *Mar 1 06:54:40.204: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:40.204: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:40.204: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:40.208: Se1/2 PAP: O AUTH-NAK id 17 len 26 msg is "Authentication failed" *Mar 1 06:54:40.208: Se1/2 PPP: Sending Acct Event[Down] id[14] *Mar 1 06:54:40.212: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:40.212: Se1/2 LCP: O TERMREQ [Open] id 42 len 4 *Mar 1 06:54:40.212: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:40.216: Se1/2 LCP: I TERMACK [TERMsent] id 42 len 4 *Mar 1 06:54:40.216: Se1/2 LCP: State is Closed *Mar 1 06:54:40.220: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:40.220: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:40.220: Se1/2 LCP: State is Listen *Mar 1 06:54:42.231: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:42.231: Se1/2 LCP: O CONFREQ [Listen] id 43 len 14 *Mar 1 06:54:42.231: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:42.231: Se1/2 LCP: MagicNumber 0x14DCA6C0 (0x050614DCA6C0) *Mar 1 06:54:42.240: Se1/2 LCP: I CONFREQ [REQsent] id 19 len 14 *Mar 1 06:54:42.240: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:42.240: Se1/2 LCP: MagicNumber 0x14FAC092 (0x050614FAC092) *Mar 1 06:54:42.244: Se1/2 LCP: O CONFACK [REQsent] id 19 len 14 *Mar 1 06:54:42.244: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:42.244: Se1/2 LCP: MagicNumber 0x14FAC092 (0x050614FAC092) *Mar 1 06:54:42.244: Se1/2 LCP: I CONFACK [ACKsent] id 43 len 14 *Mar 1 06:54:42.244: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:42.244: Se1/2 LCP: MagicNumber 0x14DCA6C0 (0x050614DCA6C0) *Mar 1 06:54:42.244: Se1/2 LCP: State is Open *Mar 1 06:54:42.248: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:42.248: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:42.248: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:42.248: Se1/2 PAP: O AUTH-REQ id 18 len 22 from "One" *Mar 1 06:54:42.252: Se1/2 PAP: I AUTH-REQ id 18 len 14 from "Two" *Mar 1 06:54:42.252: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:42.252: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:42.252: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:42.256: Se1/2 PAP: O AUTH-NAK id 18 len 26 msg is "Authentication failed" *Mar 1 06:54:42.256: Se1/2 PPP: Sending Acct Event[Down] id[15] *Mar 1 06:54:42.260: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:42.260: Se1/2 LCP: O TERMREQ [Open] id 44 len 4 *Mar 1 06:54:42.260: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:42.264: Se1/2 LCP: I TERMACK [TERMsent] id 44 len 4 *Mar 1 06:54:42.264: Se1/2 LCP: State is Closed *Mar 1 06:54:42.268: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:42.268: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:42.268: Se1/2 LCP: State is Listen *Mar 1 06:54:44.279: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:44.279: Se1/2 LCP: O CONFREQ [Listen] id 45 len 14 *Mar 1 06:54:44.279: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:44.279: Se1/2 LCP: MagicNumber 0x14DCAEC0 (0x050614DCAEC0) *Mar 1 06:54:44.287: Se1/2 LCP: I CONFREQ [REQsent] id 20 len 14 *Mar 1 06:54:44.287: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:44.287: Se1/2 LCP: MagicNumber 0x14FAC896 (0x050614FAC896) *Mar 1 06:54:44.291: Se1/2 LCP: O CONFACK [REQsent] id 20 len 14 *Mar 1 06:54:44.291: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:44.291: Se1/2 LCP: MagicNumber 0x14FAC896 (0x050614FAC896) *Mar 1 06:54:44.291: Se1/2 LCP: I CONFACK [ACKsent] id 45 len 14 *Mar 1 06:54:44.291: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:44.291: Se1/2 LCP: MagicNumber 0x14DCAEC0 (0x050614DCAEC0) *Mar 1 06:54:44.295: Se1/2 LCP: State is Open *Mar 1 06:54:44.295: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:44.295: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:44.295: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:44.295: Se1/2 PAP: O AUTH-REQ id 19 len 22 from "One" *Mar 1 06:54:44.299: Se1/2 PAP: I AUTH-REQ id 19 len 14 from "Two" *Mar 1 06:54:44.299: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:44.299: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:44.299: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:44.303: Se1/2 PAP: O AUTH-NAK id 19 len 26 msg is "Authentication failed" *Mar 1 06:54:44.303: Se1/2 PPP: Sending Acct Event[Down] id[16] *Mar 1 06:54:44.307: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:44.307: Se1/2 LCP: O TERMREQ [Open] id 46 len 4 *Mar 1 06:54:44.307: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:44.311: Se1/2 LCP: I TERMACK [TERMsent] id 46 len 4 *Mar 1 06:54:44.315: Se1/2 LCP: State is Closed *Mar 1 06:54:44.315: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:44.315: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:44.315: Se1/2 LCP: State is Listen *Mar 1 06:54:46.326: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:46.326: Se1/2 LCP: O CONFREQ [Listen] id 47 len 14 *Mar 1 06:54:46.326: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:46.326: Se1/2 LCP: MagicNumber 0x14DCB6C1 (0x050614DCB6C1) *Mar 1 06:54:46.334: Se1/2 LCP: I CONFREQ [REQsent] id 21 len 14 *Mar 1 06:54:46.334: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:46.334: Se1/2 LCP: MagicNumber 0x14FAD092 (0x050614FAD092) *Mar 1 06:54:46.338: Se1/2 LCP: O CONFACK [REQsent] id 21 len 14 *Mar 1 06:54:46.338: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:46.338: Se1/2 LCP: MagicNumber 0x14FAD092 (0x050614FAD092) *Mar 1 06:54:46.338: Se1/2 LCP: I CONFACK [ACKsent] id 47 len 14 *Mar 1 06:54:46.338: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:46.338: Se1/2 LCP: MagicNumber 0x14DCB6C1 (0x050614DCB6C1) *Mar 1 06:54:46.338: Se1/2 LCP: State is Open *Mar 1 06:54:46.342: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:54:46.342: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:54:46.342: Se1/2 PAP: Using password from interface PAP *Mar 1 06:54:46.342: Se1/2 PAP: O AUTH-REQ id 20 len 22 from "One" *Mar 1 06:54:46.346: Se1/2 PAP: I AUTH-REQ id 20 len 14 from "Two" *Mar 1 06:54:46.346: Se1/2 PAP: Authenticating peer Two *Mar 1 06:54:46.346: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:54:46.346: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:54:46.350: Se1/2 PAP: O AUTH-NAK id 20 len 26 msg is "Authentication failed" *Mar 1 06:54:46.350: Se1/2 PPP: Sending Acct Event[Down] id[17] *Mar 1 06:54:46.354: Se1/2 PPP: Phase is TERMINATING *Mar 1 06:54:46.354: Se1/2 LCP: O TERMREQ [Open] id 48 len 4 *Mar 1 06:54:46.354: Se1/2 PAP: LCP not open, discarding packet *Mar 1 06:54:46.358: Se1/2 LCP: I TERMACK [TERMsent] id 48 len 4 *Mar 1 06:54:46.362: Se1/2 LCP: State is Closed *Mar 1 06:54:46.362: Se1/2 PPP: Phase is DOWN *Mar 1 06:54:46.362: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 06:54:46.362: Se1/2 LCP: State is Listen *Mar 1 06:54:48.374: Se1/2 LCP: TIMEout: State Listen *Mar 1 06:54:48.374: Se1/2 LCP: O CONFREQ [Listen] id 49 len 14 *Mar 1 06:54:48.374: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:48.374: Se1/2 LCP: MagicNumber 0x14DCBEC1 (0x050614DCBEC1) *Mar 1 06:54:48.382: Se1/2 LCP: I CONFREQ [REQsent] id 22 len 14 *Mar 1 06:54:48.382: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:54:48.382: Se1/2 LCP: MagicNumber 0x14FAD893 (0x050614FAD893) *Mar 1 06:54:48.386: Se1/2 LCP: O CONFACK [REQsent] id 22 len 14 RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 06:5 R3(config-if)#shut R3(config-if)#shut *Mar 1 06:54:58.646: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down R3(config-if)#shutppp pap sent Two pass cisco     For-The_ -Show R3(config-if)#no shut R3(config-if)#^Z R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] 1 06:54:48.386: Se1/2 LC R2(config-if)#shutnshutoshut shutsshuthshutushutshut shut hut  R2(config-if)#^Z R2# *Mar 1 06:55:24.893: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:55:24.917: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 06:55:24.942: Se1/2 PPP: Outbound cdp packet dropped R2# *Mar 1 06:55:25.743: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 06:55:26.873: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 06:55:26.873: Se1/2 PPP: Using default call direction *Mar 1 06:55:26.873: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 06:55:26.873: Se1/2 PPP: Session handle[5100001D] Session id[28] *Mar 1 06:55:26.873: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 06:55:26.873: Se1/2 LCP: O CONFREQ [Closed] id 61 len 14 *Mar 1 06:55:26.873: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:55:26.877: Se1/2 LCP: MagicNumber 0x14DD552A (0x050614DD552A) *Mar 1 06:55:26.881: Se1/2 LCP: I CONFREQ [REQsent] id 28 len 14 *Mar 1 06:55:26.881: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:55:26.881: Se1/2 LCP: MagicNumber 0x14FB6EFC (0x050614FB6EFC) *Mar 1 06:55:26.881: Se1/2 LCP: O CONFACK [REQsent] id 28 len 14 *Mar 1 06:55:26.881: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:55:26 R2#.881: Se1/2 LCP: MagicNumber 0x14FB6EFC (0x050614FB6EFC) *Mar 1 06:55:26.885: Se1/2 LCP: I CONFACK [ACKsent] id 61 len 14 *Mar 1 06:55:26.885: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 06:55:26.885: Se1/2 LCP: MagicNumber 0x14DD552A (0x050614DD552A) *Mar 1 06:55:26.885: Se1/2 LCP: State is Open *Mar 1 06:55:26.885: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 06:55:26.885: Se1/2 PAP: Using hostname from interface PAP *Mar 1 06:55:26.885: Se1/2 PAP: Using password from interface PAP *Mar 1 06:55:26.885: Se1/2 PAP: O AUTH-REQ id 27 len 22 from "One" *Mar 1 06:55:26.889: Se1/2 PAP: I AUTH-REQ id 27 len 21 from "Two" *Mar 1 06:55:26.893: Se1/2 PAP: Authenticating peer Two *Mar 1 06:55:26.893: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:55:26.893: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 06:55:26.893: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 06:55:26.897: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 06:55:26.897: Se1/2 PAP: O AUTH-ACK id 27 len 5 *Mar 1 06:55:26.901: Se1/2 PAP: I AUTH-ACK id 27 len 5 *Mar 1 06:55:26.901: Se1/2 PPP: Phase is UP *Mar 1 06:55:26.901: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 06:55:26.901: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:55:26.901: Se1/2 PPP: Process pending ncp packets *Mar 1 06:55:26.905: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 06:55:26.905: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 06:55:26.909: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:55:26.909: Se1/2 AAA/AUTHOR/IPCP: Start. Her address 180.40.7.3, we want 0.0.0.0 *Mar 1 06:55:26.909: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 06:55:26.909: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 06:55:26.913: Se1/2 AAA/AUTHOR/IPCP: Reject 180.40.7.3, using 0.0.0.0 *Mar 1 06:55:26.913: Se1/2 AAA/AUTHOR/IPCP: Done. Her address 180.40.7.3, we want 0.0.0.0 *Mar 1 06:55:26.913: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 06:55:26.913: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 06:55:26.913: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 06:55:26.913: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 06:55:26.917: Se1/2 IPCP: State is Open *Mar 1 06:55:26.917: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 06:55:26.917: Se1/2 CDPCP: State is Open *Mar 1 06:55:26.917: Se1/2 IPCP: Install route to 180.40.7.3 *Mar 1 06:55:26.921: Se1/2 IPCP: Add link info for cef entry 180.40.7.3 *Mar 1 06:55:27.902: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2# R2# R2# R2# R2#sh run | us  b user username Two password 0 For-The-Show ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 duplex auto speed auto --More--  ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue no frame-relay inverse-arp ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 broadcast frame-relay map ip 208.28.1.2 203 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp authentication pap optional ppp pap sent-username One password 0 For-The-Money ! --More--   R2#^x3 % Unknown command or computer name, or unable to find computer address R2# R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run | b user username One password 0 For-The-Money ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto --More--  ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.2 302 broadcast frame-relay map ip 208.28.1.3 302 broadcast no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show ! interface Serial1/3 no ip address --More--   R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#user R1 pass PinkCadillac R3(config)# RACK13AS>3 1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#usd er R3 pass PrinkCadillac R1(config)#int s 0/0.1 R1(config-subif)#do sh run int s 0/9.1 sh run int s 0/9.1 ^ % Invalid input detected at '^' marker. R1(config-subif)#do sh run int s 0/9.1.1 0.1 Building configuration... Current configuration : 118 bytes ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 end R1(config-subif)#frame-relay interface-dlci 103 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R1(config-subif)#frame-relay interface-dlci 103 ppp ? Virtual-Template Virtual Template interface R1(config-subif)#frame-relay interface-dlci 103 ppp vi R1(config-subif)#frame-relay interface-dlci 103 ppp virtual-Template ? <1-200> Virtual-Template interface number R1(config-subif)#frame-relay interface-dlci 103 ppp virtual-Template 1 R1(config-fr-dlci)# *Mar 1 07:03:11.992: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R1(config-fr-dlci)#exit R1(config-subif)#exit R1(config)#exitframe-relay interface-dlci 103 ppp virtual-Template 1do sh run int s 0/0.1 frame-relay interface-dlci 103 ppp virtual-Template 1exit  int vir R1(config)#int virtual-temp R1(config)#int virtual-template 1 R1(config-if)# R1(config-if)#ip add 208.28.1.1 255.255.255.248 R1(config-if)#int s 0/0.1 R1(config-subif)#no ip addr R1(config-subif)#i no ip addrint s 0/0.1p add 208.28.1.1 255.255.255.248nt virtual-template 1  R1(config-if)#ppp authen chap R1(config-if)#^Z R1# *Mar 1 07:05:03.146: %SYS-5-CONFIG_I: Configur