=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.04.27 11:40:19 =~=~=~=~=~=~=~=~=~=~=~= config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#no fram inv R3(config-if)#no fram inverse-arp R3(config-if)#fram map ip 208.29.1.    8.1.1 301 R3(config-if)#fram map ip 208.28.1.1 301 1 2  302 3 302  R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0 R2(config-if)#no fram  R2(config-if)#no fram inv R2(config-if)#no fram inverse-arp R2(config-if)#int s 1/0.1 R2(config-subif)#fram map ip 208.28.1.2 203 R2(config-subif)#int s 1/0.2 R2(config-subif)#fram map ip 208.28.       180.40.7.66 201 R2(config-subif)#^Z R2# *Mar 1 03:35:47.796: %SYS-5-CONFIG_I: Configured from console by console R2#sh run int s       | b int s       1/0 interface Serial1/0 no ip address encapsulation frame-relay no frame-relay inverse-arp ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.2 203 frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clock rate 64000 ! --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#^Z R3#sh run int s 1 *Mar 1 03:36:19.656: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int s 1/0 Building configuration... Current configuration : 191 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp end R3# R3#sh run     ip int s 1/0 Serial1/0 is up, line protocol is up Internet address is 208.28.1.2/29 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is disabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is enabled IP Flow switching is disabled IP CEF switching is enabled IP CEF Fast switching turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled --More--   R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1>en R1#do shr  r       sh run int     line con 0 ^ % Invalid input detected at '^' marker. R1#sh run line con 00n |line con 0 line con 0bline con 0 line con 0 line con 0 line aux 0 line vty 0 4 ! ! end R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#line con 0 R1(config-line)#no exec- R1(config-line)#no exec-ti R1(config-line)#no exec-timeout R1(config-line)#log syn % Ambiguous command: "log syn" R1(config-line)#log sync % Ambiguous command: "log sync" R1(config-line)#~~log syncg sync R1(config-line)#priv R1(config-line)#privi R1(config-line)#privilege leve R1(config-line)#privilege level 15 R1(config-line)#router eigrp 100 R1(config-router)#net 208.28.1.66 0.0.0.0 R1(config-router)#net 180.40.7.66 0..0.\    0.0.0 R1(config-router)#nei 2 180.40.7.65 s 0/0.2 R1(config-router)#^Z R1# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#router eigrp 100 S5(config-router)#net 208.28.1.65 0.0.0.0 S5(config-router)#net 208.28.1.65 0.0.0.0~  03:45:01: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.66 (Vlan10) is up: new adjacency S5(config-router)#net 208.28.1.65 0.0.0.0 0.0.0.0  0.0.0.0 1 0.0.0.03 0.0.0.00 0.0.0.0 S5(config-router)#^Z S5# RACK13AS>c2 [confirm] [OK] RACK13AS>config         [Resuming connection 5 to r5 ... ] 0 S5# RACK13AS>2 [Resuming connection 2 to r2 ... ] [Connection to r2 closed by foreign host] RACK13AS> [Resuming connection 5 to r5 ... ] RACK13AS>r2 Translating "r2" Trying R2 (1.1.1.1, 2002)... Open ! ************************************************************** Global Knowledge Hands-On Labs Access Server Access is restricted to Global Knowledge CCIE Students ************************************************************** Please re-enter your password. (This is the same password you used to log onto the Lab website.) If you see a username prompt, please wait 40 seconds and try again. If the username prompt persists, please reset equipment from your "Pod x" link. User Access Verification Password: Password OK R2#en R2# R2# R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#rotuer      uter eigrp 100 R2(config-router)#net 208.28.1.129 0.0.0.0 R2(config-router)#net 180.40 *Mar 1 03:42:41.293: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.130 (FastEthernet0/1) is up: new adjacency R2(config-router)#net 180.40.7.65 0.0.0.0 R2(config-router)#\ nei 180.40.7.66 s 1/0.2 R2(config-router)#^Z R2# *Mar 1 03:42:57.772: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is up: new adjacency *Mar 1 03:42:58.742: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip euig   igrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 13 00:00:10 1 5000 1 0 0 208.28.1.130 Fa0/1 10 00:00:27 732 4392 0 4 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 14 00:00:14 1 5000 1 0 0 208.28.1.130 Fa0/1 11 00:00:30 732 4392 0 4 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 13 00:00:15 1 5000 1 0 0 208.28.1.130 Fa0/1 10 00:00:31 732 4392 0 4 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 11 00:00:16 1 5000 1 0 0 208.28.1.130 Fa0/1 14 00:00:33 732 4392 0 4 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 10 00:00:17 1 5000 1 0 0 208.28.1.130 Fa0/1 13 00:00:34 732 4392 0 4 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 13 00:00:19 1 5000 1 0 0 208.28.1.130 Fa0/1 11 00:00:35 732 4392 0 4 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 12 00:00:20 1 5000 1 0 0 208.28.1.130 Fa0/1 14 00:00:37 732 4392 0 4 R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 11 00:00:27 1 5000 1 0 0 208.28.1.130 Fa0/1 13 00:00:43 732 4392 0 4 R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 12 00:01:37 4 200 0 3 R1#sh run | b router router eigrp 100 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! no ip http server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 privilege level 15 logging synchronous line aux 0 line vty 0 4 ! --More--   R1#ping *Mar 1 03:45:01.932: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.65 (Serial0/0.2) is up: new adjacency R1#ping sh run | b routerip eigrp nei  IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.65 Se0/0.2 175 00:00:05 252 1512 0 4 0 208.28.1.65 Et0/0 13 00:01:58 4 200 0 3 R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 12 00:00:58 1 5000 0 3 0 208.28.1.130 Fa0/1 10 00:01:14 732 4392 0 4 R2# RACK13AS>5 [Resuming connection 5 to r5 ... ] 03:4 S5#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 208.28.1.129 Vl20 14 00:01:23 1 3000 0 3 0 208.28.1.66 Vl10 11 00:02:08 166 996 0 2 S5#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.128/27 is directly connected, Vlan20 C 208.28.1.64/28 is directly connected, Vlan10 D 180.40.0.0/16 [90/2170112] via 208.28.1.66, 00:01:19, Vlan10 S5# S5# S5# S5# S5# RACK13AS>c 1 [Resuming connection 1 to r1 ... ] R1#sh run | b router router eigrp 100 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! no ip http server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 privilege level 15 logging synchronous line aux 0 line vty 0 4 ! --More--   R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b 1/0.2 interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address --More--   shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router eigrp 100 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! --More--   R2# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | b rouetr S5#sh run | b rouetr   ter router eigrp 100 network 208.28.1.65 0.0.0.0 network 208.28.1.130 0.0.0.0 auto-summary ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 no login line vty 5 15 no login ! ! --More--   S5# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router rip R3(config-router)#ver 2 R3(config-router)#no autop R3(config-router)#no autop\   R3(config-router)#no auto-summary R3(config-router)#net 208./  .28.1.0 R3(config-router)#net 208.28.1.0          180.40.0.0 R3(config-router)#nei 208.28.1.1 R3(config-router)#nei 208.28.1.1 2 R3(config-router)#nei 208.28.1.2 3 R3(config-router)#nei 208.28.1.32nnei 208.28.1.2onei 208.28.1.2 nei 208.28.1.2 R3(config-router)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router rip R1(config-router)#ver 2 R1(config-router)#no auto R1(config-router)#pas R1(config-router)#passive-interface e 0/0 R1(config-router)#net 208.28.1.0 R1(config-router)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#ver 2 R2(config-router)#nop auto       auto R2(config-router)#pass R2(config-router)#passive-interface fa 0/1 R2(config-router)#p[as   as R2(config-router)#passive-interface ser 1/0.2 R2(config-router)#net 208.28.1.0 R2(config-router)#net 180.40.0.0 R2(config-router)#nei 290  08.28.1.2 R2(config-router)#^Z R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#^Z R3#sh ip *Mar 1 03:49:11.433: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:12, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.0 is directly connected, Serial1/2 R 180.40.7.64 [120/1] via 180.40.7.2, 00:00:16, Serial1/2 R3# sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:15, Serial1/0 [120/1] via 180.40.7.2, 00:00:09, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:02, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.0 is directly connected, Serial1/2 R 180.40.7.64 [120/1] via 180.40.7.2, 00:00:10, Serial1/2 [120/1] via 208.28.1.3, 00:00:16, Serial1/0 R3# sh ip proto Routing Protocol is "rip" Sending updates every 30 seconds, next due in 15 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: rip Neighbor(s): 208.28.1.3 208.28.1.1 Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial1/0 2 2 Serial1/2 2 2 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 180.40.0.0 208.28.1.0 Routing Information Sources: Gateway Distance Last Update 180.40.7.2 120 00:00:22 208.28.1.1 120 00:00:16 208.28.1.3 120 00:00:03 --More--   Distance: (default is 120) R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1(config-router)#do sh ip proto Routing Protocol is "eigrp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates Default networks accepted from incoming updates EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0 EIGRP maximum hopcount 100 EIGRP maximum metric variance 1 Redistributing: eigrp 100 EIGRP NSF-aware route hold timer is 240s Automatic network summarization is in effect Automatic address summarization: 208.28.1.0/24 for Serial0/0.2 Summarizing with metric 281600 180.40.0.0/16 for Ethernet0/0 Summarizing with metric 2169856 Maximum path: 4 Routing for Networks: 180.40.7.66/32 208.28.1.66/32 Routing Information Sources: Gateway Distance Last Update (this router) 90 00:06:13 --More--   Gateway Distance Last Update 208.28.1.65 90 00:08:01 180.40.7.65 90 00:06:14 Distance: internal 90 external 170 Routing Protocol is "rip" Sending updates every 30 seconds, next due in 26 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: rip Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial0/0.1 2 2 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 208.28.1.0 Passive Interface(s): Ethernet0/0 Routing Information Sources: Gateway Distance Last Update 208.28.1.2 120 00:00:24 --More--   Distance: (default is 120) R1(config-router)#do sh ip rotue sh ip rotue ^ % Invalid input detected at '^' marker. R1(config-router)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 5 subnets, 4 masks D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:08:15, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 R 208.28.1.0/29 [120/1] via 208.28.1.2, 00:00:09, Serial0/0.1 C 208.28.1.0/28 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:06:28, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:10, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:09:05, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1(config-router)#int s 1/0   0/0.1 R1(config-subif)#ip addres 208.28.1.1 255.255.255.248 R1(config-subif)#ip addres 208.28.1.1 255.255.255.248nt s 0/0.1 do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:09:14, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:07:27, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:05, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:10:05, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1(config-subif)#router rip R1(config-router)#redis R1(config-router)#redistribute eigrp 1 ? metric Metric for redistributed routes route-map Route map reference R1(config-router)#redistribute eigrp 1 met 2 R1(config-router)#router rip R1(config-router)#re  router eigrp rip edistribute eigrp 1 met 20 met 20 met 2 R1(config-router)#redistribute eigrp 100 met 2outer rip edistribute eigrp 1 met 2nredistribute eigrp 1 met 2oredistribute eigrp 1 met 2 redistribute eigrp 1 met 2 R1(config-router)#do sh run | b or  router router eigrp 100 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 2 passive-interface Ethernet0/0 network 208.28.1.0 no auto-summary ! no ip http server ip classless ! ! ! ! ! ! ! ! --More--   R1(config-router)#router eigrp 100 R1(config-router)#redis rip R1(config-router)#redis rip met R1(config-router)#redis rip metric ? <1-4294967295> Bandwidth metric in Kbits per second R1(config-router)#redis rip metric 128 ? <0-4294967295> EIGRP delay metric, in 10 microsecond units R1(config-router)#redis rip metric 128 2000 ? <0-255> EIGRP reliability metric where 255 is 100% reliable R1(config-router)#redis rip metric 128 2000 255 1 1500 R1(config-router)#int s 1/  0/0.1 R1(config-subif)#band 128 R1(config-subif)#band 128int s 0/0.1 2 R1(config-subif)#int s 0/0.2band 128  R1(config-subif)#^Z R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#rotuer      uter rip R2(config-router)#redis eigr 100 met 2 R2(config-router)#rotuer      ute i  r eirp 100 ^ % Invalid input detected at '^' marker. R2(config)#router eirp 100edis eigr 100 met 2outer eirp 100 grp 100 R2(config-router)#rre   redis rip met 128 2000 255 1 1500 R2(config-router)#^Z R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:18, Serial1/0 [120/1] via 180.40.7.2, 00:00:04, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:17, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:17, Serial1/0 [120/2] via 180.40.7.2, 00:00:05, Serial1/2 [120/2] via 208.28.1.3, 00:00:19, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:18, Serial1/0 --More--   [120/2] via 180.40.7.2, 00:00:05, Serial1/2 [120/2] via 208.28.1.3, 00:00:19, Serial1/0 R 180.40.7.64/27 [120/1] via 180.40.7.2, 00:00:06, Serial1/2 [120/1] via 208.28.1.3, 00:00:19, Serial1/0 R3#ping 208.28.1.65 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/61 ms R3#ping 208.28.1.65  `1  130 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/44/45 ms R3#ping 208.28.1.130 sou 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: Packet sent with a source address of 208.28.1.2 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/44/44 ms R3#ping 208.28.1.130 sou 208.28.1.2 sou 208.28.1.2  sou 208.28.1.2  sou 208.28.1.2 6 sou 208.28.1.25 sou 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: Packet sent with a source address of 208.28.1.2 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R3#^x1 % Unknown command or computer name, or unable to find computer address R3# R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 2 passive-interface Ethernet0/0 network 208.28.1.0 no auto-summary ! no ip http server ip classless ! ! ! ! ! ! ! --More--   R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run | b router   router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 2 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b router router rip version 2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! line con 0 --More--   R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#key R3(config)#key  R3(config)#key ch R3(config)#key chain ? WORD Key-chain name R3(config)#key chain Prob4 R3(config-keychain)#key R3(config-keychain)#key 1 R3(config-keychain-key)#key R3(config-keychain-key)#key-string cisco R3(config-keychain-key)#int s 1/2 R3(config-if)#shut R3(config-if)#ip *Mar 1 04:05:42.638: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 04:05:43.640: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#ip auth R3(config-if)#ip auth R3(config-if)#ip authen R3(config-if)#ip authentication ? key-chain key-chain mode mode R3(config-if)#ip authentication key R3(config-if)#ip authentication key-chain ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) R3(config-if)#ip authentication key-chain                          rip ? advertise Specify update interval authentication Authentication control receive advertisement reception send advertisement transmission triggered enable rfc2091 triggered rip v2-broadcast send ip broadcast v2 update R3(config-if)#ip rip ay uthe R3(config-if)#ip rip authentication ? key-chain Authentication key-chain mode Authentication mode R3(config-if)#ip rip authentication key R3(config-if)#ip rip authentication key-chain ? LINE name of key-chain R3(config-if)#ip rip authentication key-chain Prob4 R3(config-if)#ip rip authen R3(config-if)#ip rip authentication m R3(config-if)#ip rip authentication mode m R3(config-if)#ip rip authentication mode md5 ? R3(config-if)#ip rip authentication mode md5 R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#key chai R2(config)#key chain Prob4 R2(config-keychain)#key 1 R2(config-keychain-key)#ke R2(config-keychain-key)#key-string cisco R2(config-keychain-key)#int s 1/2 R2(config-if)#ip rip authen R2(config-if)#ip rip authentication mod R2(config-if)#ip rip authentication mode m R2(config-if)#ip rip authentication mode md5 R2(config-if)#ip rip authen ke R2(config-if)#ip rip authen key-chain Prob4 R2(config-if)#^Z R2# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2# *Mar 1 04:06:56.427: %SYS-5-CONFIG_I: Configured from console by console R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh    deb ip rip RIP protocol debugging is on R3(config-if)#n *Mar 1 04:07:03.150: RIP: sending v2 update to 224.0.0.9 via Serial1/0 (208.28.1.2) *Mar 1 04:07:03.150: RIP: build update entries *Mar 1 04:07:03.150: 180.40.0.0/16 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:03.150: 180.40.7.64/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:03.150: 208.28.1.0/24 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:03.150: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:03.150: 208.28.1.64/28 via 208.28.1.1, metric 2, tag 0 *Mar 1 04:07:03.154: 208.28.1.128/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:03.154: RIP: sending v2 update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 04:07:03.154: RIP: build update entries *Mar 1 04:07:03.154: 180.40.0.0/16 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:03.154: 180.40.7.64/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:03.154: 208.28.1.0/24 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:03.154: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:03.158: 208. R3(config-if)#28.1.64/28 via 208.28.1.1, metric 2, tag 0 *Mar 1 04:07:03.158: 208.28.1.128/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:03.158: RIP: sending v2 update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 04:07:03.158: RIP: build update entries *Mar 1 04:07:03.158: 180.40.0.0/16 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:03.158: 180.40.7.64/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:03.158: 208.28.1.0/24 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:03.162: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:03.162: 208.28.1.64/28 via 208.28.1.1, metric 2, tag 0 *Mar 1 04:07:03.162: 208.28.1.128/27 via 208.28.1.3, metric 2, tag 0no shut R3(config-if)# *Mar 1 04:07:08.130: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up R3(config-if)# *Mar 1 04:07:08.134: RIP: sending request on Serial1/2 to 224.0.0.9 *Mar 1 04:07:08.134: RIP: sending request on Serial1/2 to 224.0.0.9 *Mar 1 04:07:08.202: RIP: received packet with MD5 authentication *Mar 1 04:07:08.206: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 04:07:08.206: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 04:07:08.206: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 04:07:08.206: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 04:07:08.206: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 04:07:08.210: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 04:07:08.210: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 04:07:08.230: RIP: received packet with MD5 authentication *Mar 1 04:07:08.230: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 04:07:08.230: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 04:07:08.230: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 04:07:08.230: 208.28.1.0/24 via 0.0.0.0 R3(config-if)# in 2 hops *Mar 1 04:07:08.234: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 04:07:08.234: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 04:07:08.234: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 04:07:08.242: RIP: received packet with MD5 authentication *Mar 1 04:07:08.242: RIP: received v2 request from 180.40.7.2 on Serial1/2 *Mar 1 04:07:08.242: RIP: sending update with long TTL *Mar 1 04:07:08.242: RIP: sending v2 update to 180.40.7.2 via Serial1/2 (180.40.7.3) *Mar 1 04:07:08.242: RIP: build update entries *Mar 1 04:07:08.246: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:08.246: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:07:08.254: RIP: received packet with MD5 authentication *Mar 1 04:07:08.254: RIP: received v2 request from 180.40.7.2 on Serial1/2 *Mar 1 04:07:08.254: RIP: sending update with long TTL *Mar 1 04:07:08.258: RIP: sending v2 update to 180.40.7.2 via Serial1/2 (180.40.7.3) *Mar 1 04:07:08.258: RIP: build update entries *Mar 1 04:07:08.258: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:08.258: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:07:09.132: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up *Mar 1 04:07:10.133: RIP: sending v2 flash update to 224.0.0.9 via Serial1/0 (208.28.1.2) *Mar 1 04:07:10.133: RIP: build flash update entries *Mar 1 04:07:10.133: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:10.133: RIP: sending v2 flash update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 04:07:10.133: RIP: build flash update entries *Mar 1 04:07:10.133: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:10.133: RIP: sending v2 flash update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 04:07:10.137: RIP: build flash update entries *Mar 1 04:07:10.137: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:10.137: RIP: sending v2 flash update to 224.0.0.9 via Serial1/2 (180.40.7.3) *Mar 1 04:07:10.137: RIP: build flash update entries - suppressing null update *Mar 1 04:07:10.157: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 04:07:10.157: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 04:07:10.931: RIP: received v2 update from 208.28.1.1 on Serial1/0 *Mar 1 04:07:10.931: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 04:07:10.931: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 04:07:10.931: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 04:07:10.931: 208.28.1.64/28 via 0.0.0.0 in 1 hops *Mar 1 04:07:10.931: 208.28.1.128/27 via 0.0.0.0 in 2 hops R3(config-if)# R3(config-if)# *Mar 1 04:07:21.348: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 04:07:21.348: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 04:07:21.348: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 04:07:21.352: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 04:07:21.352: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 04:07:21.352: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 04:07:21.352: 208.28.1.128/27 via 0.0.0.0 in 1 hops R3(config-if)# *Mar 1 04:07:30.098: RIP: sending v2 update to 224.0.0.9 via Serial1/0 (208.28.1.2) *Mar 1 04:07:30.098: RIP: build update entries *Mar 1 04:07:30.098: 180.40.0.0/16 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:30.098: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:30.098: 180.40.7.64/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:30.098: 208.28.1.0/24 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:30.098: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:30.102: 208.28.1.64/28 via 208.28.1.1, metric 2, tag 0 *Mar 1 04:07:30.102: 208.28.1.128/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:30.102: RIP: sending v2 update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 04:07:30.102: RIP: build update entries *Mar 1 04:07:30.102: 180.40.0.0/16 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:30.102: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:30.102: 180.40.7.64/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:30.106: 208.28. R3(config-if)#1.0/24 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:30.106: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:30.106: 208.28.1.64/28 via 208.28.1.1, metric 2, tag 0 *Mar 1 04:07:30.106: 208.28.1.128/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:30.106: RIP: sending v2 update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 04:07:30.106: RIP: build update entries *Mar 1 04:07:30.106: 180.40.0.0/16 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:30.110: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:30.110: 180.40.7.64/27 via 208.28.1.3, metric 2, tag 0 *Mar 1 04:07:30.110: 208.28.1.0/24 via 208.28.1.1, metric 3, tag 0 *Mar 1 04:07:30.110: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:30.110: 208.28.1.64/28 via 208.28.1.1, metric 2, tag 0 *Mar 1 04:07:30.110: 208.28.1.128/27 via 208.28.1.3, metric 2, tag 0 R3(config-if)# *Mar 1 04:07:34.537: RIP: received packet with MD5 authentication *Mar 1 04:07:34.537: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 04:07:34.537: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 04:07:34.537: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 04:07:34.541: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 04:07:34.541: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 04:07:34.541: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 04:07:34.541: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 04:07:34.730: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.3) *Mar 1 04:07:34.730: RIP: build update entries R3(config-if)# *Mar 1 04:07:34.730: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:07:34.730: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 R3(config-if)#u ^Z R3# *Mar 1 04:07:37.835: RIP: received v2 update from 208.28.1.1 on Serial1/0 *Mar 1 04:07:37.839: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 04:07:37.839: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 04:07:37.839: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 04:07:37.839: 208.28.1.64/28 via 0.0.0.0 in 1 hops *Mar 1 04:07:37.839: 208.28.1.128/27 via 0.0.0.0 in 2 hops R3#u all All possible debugging has been turned off R3# *Mar 1 04:07:39.021: %SYS-5-CONFIG_I: Configured from console by console R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh run | b key key chain Prob4 key 1 key-string cisco ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay no frame-relay inverse-arp ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.2 203 frame-relay interface-dlci 203 --More--  ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip rip authentication mode md5 ip rip authentication key-chain Prob4 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown --More--   R2#sh ip proto Routing Protocol is "eigrp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates Default networks accepted from incoming updates EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0 EIGRP maximum hopcount 100 EIGRP maximum metric variance 1 Redistributing: eigrp 100, rip EIGRP NSF-aware route hold timer is 240s Automatic network summarization is in effect Automatic address summarization: 208.28.1.0/24 for Serial1/0.2 Summarizing with metric 28160 180.40.0.0/16 for FastEthernet0/1 Summarizing with metric 20512000 Maximum path: 4 Routing for Networks: 180.40.7.65/32 208.28.1.129/32 Routing Information Sources: Gateway Distance Last Update (this router) 90 00:16:55 --More--   Gateway Distance Last Update 208.28.1.130 90 00:15:26 180.40.7.66 90 00:04:09 Distance: internal 90 external 170 Routing Protocol is "rip" Sending updates every 30 seconds, next due in 27 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: eigrp 100, rip Neighbor(s): 208.28.1.2 Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial1/0.1 2 2 Serial1/2 2 2 Prob4 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 180.40.0.0 208.28.1.0 Passive Interface(s): --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b key key chain Prob4 key 1 key-string cisco ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 no ip address --More--   shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer      uter rip R3(config-router)#redis  R3(config-router)#redis   R3(config-router)#redistribute eigrp 100 met 4 R3(config-router)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1# R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#redistribute eigrp 100 met 4nredistribute eigrp 100 met 4oredistribute eigrp 100 met 4 redistribute eigrp 100 met 4 R3(config-router)#^Z R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#confi g t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#co  router rip R2(config-router)# redistribute eigrp 100 met 4 R2(config-router)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#routger     er rip R1(config-router)# redistribute eigrp 100 met 4 R1(config-router)# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#co fnhg      n onfig t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int lo 0 S5(config-if)#ip add 04:17:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up S5(config-if)#ip add 209.28.1.12 ~93   9309.28.1.193 8.28.1.193.28.1.193 255.255.255.255 S5(config-if)#ip add 208.28.1.193 255.255.255.255nt lo 0  1 S5(config-if)#int lo 1p add 208.28.1.193 255.255.255.255 04:17:49: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up S5(config-if)#ip add 208.28.1.193 255.255.255.255 255.255.255.255 4 255.255.255.255 S5(config-if)#router eigrp   100 S5(config-router)#net 208.28.1.193 0.0.0.0 S5(config-router)#net 208.28.1.193 0.0.0.0 0.0.0.0 4 0.0.0.0 S5(config-router)#^Z S5# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/4] via 180.40.7.2, 00:00:04, Serial1/2 [120/4] via 208.28.1.3, 00:00:04, Serial1/0 [120/4] via 208.28.1.1, 00:00:04, Serial1/0 R 208.28.1.194/32 [120/4] via 180.40.7.2, 00:00:02, Serial1/2 [120/4] via 208.28.1.3, 00:00:02, Serial1/0 [120/4] via 208.28.1.1, 00:00:03, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:18, Serial1/0 [120/1] via 180.40.7.2, 00:00:07, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:24, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 --More--  R 208.28.1.0/24 [120/4] via 208.28.1.1, 00:00:00, Serial1/0 [120/4] via 208.28.1.3, 00:00:23, Serial1/0 [120/4] via 180.40.7.2, 00:00:12, Serial1/2 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/4] via 208.28.1.1, 00:00:00, Serial1/0 [120/4] via 208.28.1.3, 00:00:23, Serial1/0 [120/4] via 180.40.7.2, 00:00:12, Serial1/2 R 180.40.7.64/27 [120/1] via 208.28.1.3, 00:00:23, Serial1/0 [120/1] via 180.40.7.2, 00:00:12, Serial1/2 R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1(config-router)#exit R1(config)#access-list 1 per 208.28.1.193 R1(config)#router rip R1(config-router)#of R1(config-router)#offset-list ? <0-99> Access list of networks to apply offset (0 selects all networks) <1300-1999> Access list of networks to apply offset (expanded range) WORD Access-list name R1(config-router)#offset-list 1 ? in Perform offset on incoming updates out Perform offset on outgoing updates R1(config-router)#offset-list 1 out ? <0-16> Offset R1(config-router)#offset-list 1 out 3 R1(config-router)#do sh    deb ip rip RIP protocol debugging is on R1(config-router)#^Z R1# *Mar 1 04:17:33.700: %SYS-5-CONFIG_I: Configured from console by console R1# *Mar 1 04:17:37.174: RIP: received v2 update from 208.28.1.2 on Serial0/0.1 *Mar 1 04:17:37.174: 180.40.0.0/16 via 208.28.1.3 in 5 hops *Mar 1 04:17:37.174: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 04:17:37.178: 180.40.7.64/27 via 208.28.1.3 in 2 hops *Mar 1 04:17:37.178: 208.28.1.0/24 via 208.28.1.3 in 5 hops *Mar 1 04:17:37.178: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 04:17:37.178: 208.28.1.128/27 via 208.28.1.3 in 2 hops R1#u all *Mar 1 04:17:44.938: RIP: sending v2 update to 224.0.0.9 via Serial0/0.1 (208.28.1.1) *Mar 1 04:17:44.938: RIP: build update entries *Mar 1 04:17:44.938: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 04:17:44.938: 180.40.7.64/27 via 0.0.0.0, metric 4, tag 0 *Mar 1 04:17:44.938: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 04:17:44.942: 208.28.1.64/28 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:17:44.942: 208.28.1.128/27 via 0.0.0.0, metric 4, tag 0 *Mar 1 04:17:44.942: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 04:17:44.942: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R1#u all All possible debugging has been turned off R1# RACK13AS>3 2 [Resuming connection 2 to r2 ... ] R2(config-router)#exit R2(config)#acc  ess-list 1 per 208.28.1.193 R2(config)#access-list 1 per 208.28.1.1931.193 4 per 208.28.1.194 2 per 208.28.1.194 R2(config)#router rip R2(config-router)#router ripaccess-list 2 per 208.28.1.1941 per 208.28.1.193exit  redistribute eigrp 100 met 4 2 R2(config-router)#exi R2(config)#router   -map Prb ob  5 R2(config-route-map)#match ip add 1 R2(config-route-map)#set met R2(config-route-map)#set metric 7 R2(config-route-map)#set metric 7match ip add 1route-map Prob5 20 R2(config-route-map)#route-map Prob5 20set metric 7 match ip add 1 2 R2(config-route-map)#match ip add 2route-map Prob5 20set metric 7  4 R2(config-route-map)#set metric 4match ip add 2route-map Prob5 20  30 R2(config-route-map)#router er  rip R2(config-router)#router rip-map Prob5 30set metric 4 match ip add 2route-map Prob5 20set metric 7 match ip add 1route-map Prob5 exi  redistribute eigrp 100 met 2 rout R2(config-router)# redistribute eigrp 100 met 2 route-map ? WORD Pointer to route-map entries R2(config-router)# redistribute eigrp 100 met 2 route-map Prob5 ? R2(config-router)# redistribute eigrp 100 met 2 route-map Prob5 R2(config-router)#^Z R2#de *Mar 1 04:18:38.249: %SYS-5-CONFIG_I: Configured from console by console R2#deb ip rip RIP protocol debugging is on R2# *Mar 1 04:18:48.093: RIP: received packet with MD5 authentication *Mar 1 04:18:48.093: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 04:18:48.093: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 04:18:48.097: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 04:18:48.097: 208.28.1.193/32 via 0.0.0.0 in 8 hops *Mar 1 04:18:48.097: 208.28.1.194/32 via 0.0.0.0 in 5 hops R2# *Mar 1 04:19:02.413: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 04:19:02.413: RIP: build update entries *Mar 1 04:19:02.413: 180.40.0.0/16 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:19:02.413: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:19:02.413: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:19:02.413: 208.28.1.0/24 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:19:02.413: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:19:02.417: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:19:02.417: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 04:19:02.417: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2# *Mar 1 04:19:02.417: RIP: sending v2 update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 04:19:02.417: RIP: build update entries *Mar 1 04:19:02.417: 180.40.0.0/16 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:19:02.417: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:19:02.421: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:19:02.421: 208.28.1.0/24 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:19:02.421: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:19:02.421: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:19:02.421: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 04:19:02.421: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2#u all All possible debugging has been turned off R2# *Mar 1 04:19:05.506: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 04:19:05.506: RIP: build update entries *Mar 1 04:19:05.506: 180.40.0.0/16 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:19:05.506: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:19:05.506: 208.28.1.0/24 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:19:05.506: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:19:05.506: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 *Mar 1 04:19:05.510: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 04:19:05.510: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 04:19:05.510: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2#^x3 % Unknown command or computer name, or unable to find computer address R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.3, 00:00:03, Serial1/0 [120/7] via 208.28.1.1, 00:00:17, Serial1/0 [120/7] via 180.40.7.2, 00:00:26, Serial1/2 R 208.28.1.194/32 [120/4] via 208.28.1.3, 00:00:03, Serial1/0 [120/4] via 208.28.1.1, 00:00:17, Serial1/0 [120/4] via 180.40.7.2, 00:00:27, Serial1/2 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:04, Serial1/0 [120/1] via 180.40.7.2, 00:00:27, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:18, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 --More--  R 208.28.1.0/24 [120/2] via 180.40.7.2, 00:00:00, Serial1/2 [120/2] via 208.28.1.3, 00:00:05, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 180.40.7.2, 00:00:00, Serial1/2 [120/2] via 208.28.1.3, 00:00:05, Serial1/0 R 180.40.7.64/27 [120/1] via 208.28.1.3, 00:00:05, Serial1/0 [120/1] via 180.40.7.2, 00:00:00, Serial1/2 R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh reun     un | b router rip router rip version 2 redistribute eigrp 100 metric 4 passive-interface Ethernet0/0 offset-list 1 out 3 network 208.28.1.0 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 ! ! ! ! ! ! line con 0 exec-timeout 0 0 privilege level 15 logging synchronous --More--   R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b router rip router rip version 2 redistribute eigrp 100 metric 2 route-map Prob5 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.194 ! route-map Prob5 permit 10 match ip address 1 set metric 7 ! route-map Prob5 permit 20 --More--   match ip address 2 --More--   set metric 4 --More--  ! --More--  route-map Prob5 permit 30 --More--  ! --More--  ! --More--  ! --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#ip rip ? advertise Specify update interval authentication Authentication control receive advertisement reception send advertisement transmission triggered enable rfc2091 triggered rip v2-broadcast send ip broadcast v2 update R2(config-if)#ip rip tr R2(config-if)#ip rip triggered ? R2(config-if)#ip rip triggered R2(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#do ip proto ip proto ^ % Invalid input detected at '^' marker. R3(config-if)#do sh ip r proto Routing Protocol is "rip" Sending updates every 30 seconds, next due in 24 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: rip Neighbor(s): 208.28.1.3 208.28.1.1 Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial1/0 2 2 Serial1/2 2 2 Prob4 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 180.40.0.0 208.28.1.0 Routing Information Sources: Gateway Distance Last Update 180.40.7.2 120 00:00:09 208.28.1.1 120 00:00:00 208.28.1.3 120 00:00:16 --More--   R3(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.3, 00:00:06, Serial1/0 [120/7] via 208.28.1.1, 00:00:19, Serial1/0 [120/7] via 180.40.7.2, 00:00:01, Serial1/2 R 208.28.1.194/32 [120/4] via 208.28.1.3, 00:00:06, Serial1/0 [120/4] via 208.28.1.1, 00:00:19, Serial1/0 [120/4] via 180.40.7.2, 00:00:02, Serial1/2 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:07, Serial1/0 [120/1] via 180.40.7.2, 00:00:02, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:20, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 --More--   R3(config-if)#int s 1/2 R3(config-if)#ip rip tr R3(config-if)#ip rip triggered R3(config-if)#^Z R3# *Mar 1 04:23:04.854: %SYS-5-CONFIG_I: Configured from console by console R3#config sh ip routeconfig t sh ip routeconfig  sh ip proto Routing Protocol is "rip" Sending updates every 30 seconds, next due in 10 seconds Invalid after 180 seconds, hold down 0, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: rip Neighbor(s): 208.28.1.3 208.28.1.1 Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial1/0 2 2 Serial1/2 2 2 Yes Prob4 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 180.40.0.0 208.28.1.0 Routing Information Sources: Gateway Distance Last Update 180.40.7.2 120 00:00:05 208.28.1.1 120 00:00:15 208.28.1.3 120 00:00:03 --More--   R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#^Z R2# *Mar 1 04:23:20.708: %SYS-5-CONFIG_I: Configured from console by console R2#sh run int s 1/2 Building configuration... Current configuration : 173 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 clock rate 64000 end R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/2 Building configuration... Current configuration : 155 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 end R3# R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eip   rip R2(config-router)#? Router configuration commands: address-family Enter Address Family command mode auto-summary Enable automatic network number summarization default Set a command to its defaults default-information Control distribution of default information default-metric Set metric of redistributed routes distance Define an administrative distance distribute-list Filter networks in routing updates exit Exit from routing protocol configuration mode flash-update-threshold Specify flash update threshold in second help Description of the interactive help system input-queue Specify input queue depth maximum-paths Forward packets over multiple paths neighbor Specify a neighbor router network Enable routing on an IP network no Negate a command or set its defaults offset-list Add or subtract offset from RIP metrics output-delay Interpacket delay for RIP updates passive-interface Suppress routing updates on an interface redistribute Redistribute information from another routing protocol timers Adjust routing timers --More--   traffic-share How to compute traffic share over alternate paths validate-update-source Perform sanity checks against source address of routing updates version Set routing protocol version R2(config-router)#tim R2(config-router)#timers ? basic Basic routing protocol update timers R2(config-router)#timers ba R2(config-router)#timers basic ? <0-4294967295> Interval between updates R2(config-router)#timers basic              tim R2(config-router)#timers        out R2(config-router)#output-delay ? <8-50> Delay in milliseconds R2(config-router)#output-delay 10 ? R2(config-router)#output-delay 10 R2(config-router)#^Z R2# *Mar 1 04:29:18.126: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 timers basic 30 180 0 240 redistribute eigrp 100 metric 2 route-map Prob5 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 output-delay 10 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer rip ^ % Invalid input detected at '^' marker. R3(config)#router e rip R3(config-router)#no v R3(config-router)#no val R3(config-router)#no validate-update-source ? R3(config-router)#no validate-update-source R3(config-router)#^Z R3#sh ru *Mar 1 04:30:57.133: %SYS-5-CONFIG_I: Configured from console by console R3#sh ru  n   | b rotuer R3#sh run | b rotuer    uter router rip version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer      uter rip R3(config-router)#max R3(config-router)#maximum-paths ? <1-6> Number of paths R3(config-router)#maximum-paths 3 R3(config-router)#^Z R3# *Mar 1 04:33:01.673: %SYS-5-CONFIG_I: Configured from console by console R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#max R2(config-router)#maximum-paths 3 R2(config-router)#^Z R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router rip R1(config-router)#max R1(config-router)#maximum-paths 3 R1(config-router)#^Z R1# *Mar 1 04:35:33.290: %SYS-5-CONFIG_I: Configured from console by console R1#sh erun      rn un | b router rip router rip version 2 redistribute eigrp 100 metric 4 passive-interface Ethernet0/0 offset-list 1 out 3 network 208.28.1.0 maximum-paths 3 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 ! ! ! ! ! ! line con 0 exec-timeout 0 0 privilege level 15 --More--   R1#a sh ip rip ? database IP RIP database R1#sh ip rip dat 180.40.0.0/16 auto-summary 180.40.0.0/16 redistributed [4] via 0.0.0.0, 180.40.7.0/27 [1] via 208.28.1.2, 00:00:00, Serial0/0.1 180.40.7.64/27 redistributed [4] via 0.0.0.0, 208.28.1.0/24 auto-summary 208.28.1.0/24 redistributed [4] via 0.0.0.0, 208.28.1.0/29 directly connected, Serial0/0.1 208.28.1.64/28 directly connected, Ethernet0/0 208.28.1.128/27 redistributed [4] via 208.28.1.65, 208.28.1.193/32 redistributed [4] via 208.28.1.65, 208.28.1.194/32 redistributed [4] via 208.28.1.65, R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#route R1(config)#route- R1(config)#route-map test R1(config-route-map)#match ip add 1 R1(config-route-map)#set met R1(config-route-map)#set metric 4 R1(config-route-map)#set metric 4match ip add 1route-map testnroute-map testoroute-map test route-map test R1(config)#no route-map testset metric 4 match ip add 1route-map test per 10 R1(config-route-map)#route-map test per 10no route-map test set metric 4 match ip add 1 R1(config-route-map)#match ip add 1route-map test per 10no route-map test set metric 4  R1(config-route-map)#set metric 4match ip add 1route-map test per 10nroute-map test per 10oroute-map test per 10 route-map test per 10 R1(config)#route R1(config)#route- R1(config)#route-map ppp per 10 R1(config-route-map)#route-map ppp per 10no route-map test per 10set metric 4 match ip add 1 R1(config-route-map)#match ip add 1route-map ppp per 10no route-map test per 10set metric 4  R1(config-route-map)#exit R1(config)#exitset metric 4match ip add 1route-map ppp per 10nroute-map ppp per 10oroute-map ppp per 10 route-map ppp per 10 R1(config)#^Z R1# *Mar 1 05:34:50.297: %SYS-5-CONFIG_I: Configured from console by console R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#rouetr os      ter ospf 1 R1(config-router)#rout R1(config-router)#router-id 1.1.1.1 R1(config-router)#net 17.0.0.0.  0.255.255.255 area 0 R1(config-router)#^Z R1# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#router ospf 1 S6(config-router)#route S6(config-router)#router-id 6.6.6.6 S6(config-router)# S6(config-router)#net 17.0.0.0 0.255.255.255 area 0 S6(config-router)#^Z S6# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer o      uter ospf 1 R3(config-router)#rout R3(config-router)#router-id 3.3.3.3.3 ^ % Invalid input detected at '^' marker. R3(config-router)#router-id 3.3.3.3.3   R3(config-router)#net 17.0.0.0 0.255.255.255 area 0 R3(config-router)#^Z R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#cofnig t ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#riote\ \     outer ospf 1 R4(config-router)#rout R4(config-router)#router-id 4.4.4.4.  R4(config-router)#net 17.0.0.0 0.255.255.255 area 0 R4(config-router)#^Z R4# *Mar 1 05:42:26.190: %SYS-5-CONFIG_I: Configured from console by console R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh run | b router ospf router ospf 1 router-id 1.1.1.1 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! router rip version 2 redistribute eigrp 100 metric 4 passive-interface Ethernet0/0 offset-list 1 out 3 network 208.28.1.0 maximum-paths 3 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 ! ! ! ! --More--   R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run | b ospf *Mar 1 05:40:36.948: %OSPF-5-ADJCHG: Process 1, Nbr 4.4.4.4 on FastEthernet0/0 from LOADING to FULL, Loading Done R3#sh run | b ospf router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! --More--   R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh run | b ospf router ospf 1 router-id 4.4.4.4 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! --More--   R4# RACK13AS>6 [Resuming connection 6 to r6 ... ] 05: S6#sh run | b ospf router ospf 1 router-id 6.6.6.6 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 line vty 0 4 login line vty 5 15 login ! ! end --More--   S6# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Serial0/0.2 180.40.7.66 YES manual up up Ethernet0/1 17.57.100.1 YES manual up up Serial0/1 unassigned YES unset administratively down down R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int lo 0 R1(config-if)#ip addres 22 22 3.1.1.1 255.255.255.0 R1(config-if)#rotuer      uter os  rip R1(config-router)#net 223.3.  1.1.1 0 R1(config-router)#int tu 0 R1(config-if)# *Mar 1 05:43:34.864: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#tun sou lo 0 R1(config-if)#tun des 222.1.1.3 R1(config-if)#ke R1(config-if)#keepalive R1(config-if)#ip add 17.17.17.. 1 % Incomplete command. R1(config-if)#ip add 17.17.17.1  ip add 17.17.17.1 255.255.255.0 R1(config-if)#^Z R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#c sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 17.80.1.1 YES manual up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 208.28.1.2 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.3 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--  Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int lo 0 R3(config-if)#ip add 222.1.1.3 255.255.255.0 R3(config-if)#int tu 0        router rip R3(config-router)#net 222.1.1.0 R3(config-router)#int ti u 0 R3(config-if)#tun sou lo *Mar 1 05:43:19.727: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R3(config-if)#tun sou lo 0 R3(config-if)#tun dest 223.1.1.1 R3(config-if)#ke R3(config-if)#keepalive R3(config-if)#ip *Mar 1 05:43:27.664: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3(config-if)#ip add 17.17.17.3 255.255.255.0 R3(config-if)#^Z R3# *Mar 1 05:43:35.886: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# R3# *Mar 1 05:43:45.638: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3# R3# R3# R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 1.1.1.1 0 FULL/ - 00:00:38 17.17.17.1 Tunnel0 4.4.4.4 1 FULL/DR 00:00:35 17.80.1.2 FastEthernet0/0 R3# R3# R3# R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.17.17.0 [110/11112] via 17.80.1.1, 00:00:08, FastEthernet0/0 C 17.80.1.0 is directly connected, FastEthernet0/0 R4# R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets O 17.17.17.0 [110/11112] via 17.80.1.1, 00:00:02, FastEthernet0/0 C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11122] via 17.80.1.1, 00:00:02, FastEthernet0/0 R4#ping 16 7.57., 100.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/72/72 ms R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#ash     sh run | b int interface Loopback0 ip address 223.1.1.1 255.255.255.0 ! interface Tunnel0 ip address 17.17.17.1 255.255.255.0 keepalive 10 3 tunnel source Loopback0 tunnel destination 222.1.1.3 ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point --More--   bandwidth 128 ip address 180.40.7.66 255.255.255.224 frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 half-duplex ! interface Serial0/1 no ip address shutdown ! router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router ospf 1 router-id 1.1.1.1 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 --More--  ! router rip version 2 redistribute eigrp 100 metric 4 passive-interface Ethernet0/0 offset-list 1 out 3 network 208.28.1.0 network 223.1.1.0 maximum-paths 3 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 ! ! ! ! ! ! line con 0 --More--   R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b int interface Loopback0 ip address 222.1.1.3 255.255.255.0 ! interface Tunnel0 ip address 17.17.17.3 255.255.255.0 keepalive 10 3 tunnel source Loopback0 tunnel destination 223.1.1.1 ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto --More--  ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 --More--   no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 17.0.0.0 0.255.255.255 area 0 ! router rip version 2 no validate-update-source --More--   timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router rip R3(config-router)#redis R3(config-router)#redistribute ospf 1 ? match Redistribution of OSPF routes metric Metric for redistributed routes route-map Route map reference vrf VPN Routing/Forwarding Instance R3(config-router)#redistribute ospf 1 mat R3(config-router)#redistribute ospf 1 match ? external Redistribute OSPF external routes internal Redistribute OSPF internal routes nssa-external Redistribute OSPF NSSA external routes R3(config-router)#redistribute ospf 1 match in R3(config-router)#redistribute ospf 1 match internal R3(config-router)#redistribute ospf 1 match internal me R3(config-router)#redistribute ospf 1 match internal metric 3 R3(config-router)#router ospf 1 R3(config-router)#redi R3(config-router)#redistribute rip suu  R3(config-router)#redistribute rip subnets R3(config-router)#^Z R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router ospf 1 R1(config-router)#redis R1(config-router)#redistribute rip su R1(config-router)#redistribute rip subnets R1(config-router)#redistribute rip subnets   *Mar 1 05:48:03.978: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 05:48:04.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 05:48:04.979: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R1(config-router)#redistribute rip subnets           ei R1(config-router)#redistribute eigrp 100 su R1(config-router)#redistribute eigrp 100 subnets R1(config-router)#router eigrp 100 R1(config-router)#redis ospf 1 met 128 2000 255 1 150 R1(config-router)#router edis ospf 1 met 128 2000 255 1 1500 R1(config-router)#redis ospf 1 met 128 2000 255 1 1500 0 router rip R1(config-router)#redis  R1(config-router)#redis osp 1 mat in me R1(config-router)#redis osp 1 mat in metric 3 R1(config-router)#^Z R1# *Mar 1 05:48:54.701: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip rout    int tu 0 Tunnel0 is up, line protocol is down Internet address is 17.17.17.1/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1476 bytes Helper address is not set Directed broadcast forwarding is disabled Multicast reserved groups joined: 224.0.0.5 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF Fast switching turbo vector IP multicast fast switching is enabled --More--   R1#sh ip int tu 0 sh *Mar 1 05:49:14.982: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.17.17.0 is directly connected, Tunnel0 R 17.80.1.0 [120/3] via 208.28.1.2, 00:00:22, Serial0/0.1 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:22, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D 208.28.1.193/32 [90/409600] via 208.28.1.65, 01:33:04, Ethernet0/0 D 208.28.1.194/32 [90/409600] via 208.28.1.65, 01:33:03, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 02:06:02, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 01:53:28, Null0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:23, Serial0/0.1 D 180.40.0.0/16 is a summary, 01:53:38, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#sh ip route *Mar 1 05:49:22.903: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:03 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:03 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:05 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:05 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:06 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:06 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:08 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:08 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 % Network not in table R1# *Mar 1 05:49:33.989: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 05:49:35.011: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 05:49:35.011: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:12 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:12 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:14 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:14 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:16 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:16 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:19 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:19 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:23 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:23 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:25 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:25 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0  *Mar 1 05:50:45.058: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:26 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:26 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:28 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:28 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:29 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:29 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:03 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:03 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:05 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:05 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:06 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:06 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:07 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:07 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:09 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:09 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:10 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:10 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:11 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:11 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:13 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:13 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:14 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:14 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1# *Mar 1 05:51:05.563: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:16 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:16 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:17 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:17 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:18 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:18 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:19 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:19 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:21 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:21 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:22 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:22 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:23 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:23 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:25 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:25 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:26 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:26 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:27 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:27 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:00 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:00 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "ospf 1", distance 110, metric 20, type extern 2, forward metric 11111 Redistributing via eigrp 100, rip Advertised by eigrp 100 metric 128 2000 255 1 1500 Last update from 17.17.17.3 on Tunnel0, 00:00:01 ago Routing Descriptor Blocks: * 17.17.17.3, from 3.3.3.3, 00:00:01 ago, via Tunnel0 Route metric is 20, traffic share count is 1 R1# *Mar 1 05:51:24.058: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 05:51:25.059: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 05:51:25.059: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do sh access-list Standard IP access list 1 10 permit 208.28.1.193 (223 matches) R1(config)#access-list 2 den R1(config)#access-list 2 deny eigrp 100,           222.1    *Mar 1 05:52:35.086: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config)#access-list 2 deny e22   222.1 *Mar 1 05:52:36.681: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1(config)#access-list 2 deny 222.1.1.0 R1(config)#access-list 2 per any R1(config)#in  router ospf 1 R1(config-router)#distr R1(config-router)#distribute-list 2 in tu 0 R1(config-router)#^Z R1# *Mar 1 05:53:06.586: %SYS-5-CONFIG_I: Configured from console by console R1#config tsh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:01 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:01 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:03 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:03 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:04 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:04 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:05 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:05 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:06 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:06 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:07 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:07 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:09 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:09 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:10 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:10 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:11 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:11 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1#sh ip route 222.1.1.0 *Mar 1 05:53:21.085: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired R1#sh ip route 222.1.1.0 Routing entry for 222.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via eigrp 100, rip, ospf 1 Advertised by eigrp 100 metric 128 2000 255 1 1500 ospf 1 subnets Last update from 208.28.1.2 on Serial0/0.1, 00:00:12 ago Routing Descriptor Blocks: * 208.28.1.2, from 208.28.1.2, 00:00:12 ago, via Serial0/0.1 Route metric is 1, traffic share count is 1 R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] * R3#sh ip rotue 222 3.1.1.0 ^ % Invalid input detected at '^' marker. R3# *Mar 1 05:52:39.132: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3#sh ip rotue 223.1.1.0e 223.1.1.0 e 223.1.1.0 ue 223.1.1.0te 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via rip, ospf 1 Advertised by ospf 1 subnets Last update from 208.28.1.1 on Serial1/0, 00:00:09 ago Routing Descriptor Blocks: * 208.28.1.1, from 208.28.1.1, 00:00:09 ago, via Serial1/0 Route metric is 1, traffic share count is 1 R3#sh ip route 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via rip, ospf 1 Advertised by ospf 1 subnets Last update from 208.28.1.1 on Serial1/0, 00:00:11 ago Routing Descriptor Blocks: * 208.28.1.1, from 208.28.1.1, 00:00:11 ago, via Serial1/0 Route metric is 1, traffic share count is 1 R3#sh ip route 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via rip, ospf 1 Advertised by ospf 1 subnets Last update from 208.28.1.1 on Serial1/0, 00:00:13 ago Routing Descriptor Blocks: * 208.28.1.1, from 208.28.1.1, 00:00:13 ago, via Serial1/0 Route metric is 1, traffic share count is 1 R3#sh ip route 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via rip, ospf 1 Advertised by ospf 1 subnets Last update from 208.28.1.1 on Serial1/0, 00:00:14 ago Routing Descriptor Blocks: * 208.28.1.1, from 208.28.1.1, 00:00:14 ago, via Serial1/0 Route metric is 1, traffic share count is 1 R3#sh ip route 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via rip, ospf 1 Advertised by ospf 1 subnets Last update from 208.28.1.1 on Serial1/0, 00:00:15 ago Routing Descriptor Blocks: * 208.28.1.1, from 208.28.1.1, 00:00:15 ago, via Serial1/0 Route metric is 1, traffic share count is 1 R3#sh ip route 223.1.1.0 *Mar 1 05:52:48.640: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3#sh ip route 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via rip, ospf 1 Advertised by ospf 1 subnets Last update from 208.28.1.1 on Serial1/0, 00:00:16 ago Routing Descriptor Blocks: * 208.28.1.1, from 208.28.1.1, 00:00:16 ago, via Serial1/0 Route metric is 1, traffic share count is 1 R3#sh ip route 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via rip, ospf 1 Advertised by ospf 1 subnets Last update from 208.28.1.1 on Serial1/0, 00:00:18 ago Routing Descriptor Blocks: * 208.28.1.1, from 208.28.1.1, 00:00:18 ago, via Serial1/0 Route metric is 1, traffic share count is 1 R3#sh ip route 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via rip, ospf 1 Advertised by ospf 1 subnets Last update from 208.28.1.1 on Serial1/0, 00:00:19 ago Routing Descriptor Blocks: * 208.28.1.1, from 208.28.1.1, 00:00:19 ago, via Serial1/0 Route metric is 1, traffic share count is 1 R3#sh ip route 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "rip", distance 120, metric 1 Redistributing via rip, ospf 1 Advertised by ospf 1 subnets Last update from 208.28.1.1 on Serial1/0, 00:00:20 ago Routing Descriptor Blocks: * 208.28.1.1, from 208.28.1.1, 00:00:20 ago, via Serial1/0 Route metric is 1, traffic share count is 1 R3#sh ip route 223.1.1.0 Routing entry for 223.1.1.0/24 Known via "ospf 1", distance 110, metric 20, type extern 2, forward metric 11111 Redistributing via rip Last update from 17.17.17.1 on Tunnel0, 00:00:00 ago Routing Descriptor Blocks: * 17.17.17.1, from 1.1.1.1, 00:00:00 ago, via Tunnel0 Route metric is 20, traffic share count is 1 R3# *Mar 1 05:52:58.131: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 05:52:59.133: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 05:52:59.133: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#do sh access-list R3(config)#access-list 1 *Mar 1 05:54:09.136: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3(config)#access-list 1 *Mar 1 05:54:18.692: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3(config)#access-list 1 per 223.1.1.0 R3(config)#router ospf 1 R3(config-router)#di *Mar 1 05:54:28.135: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 05:54:29.137: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 05:54:29.137: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-router)#dist R3(config-router)#dista R3(config-router)#distance ? <1-255> Administrative distance ospf OSPF distance R3(config-router)#distance 255 ? A.B.C.D IP Source address R3(config-router)#distance 255 1.1.1.1 ? A.B.C.D Wildcard bits R3(config-router)#distance 255 1.1.1.1 0.0.0.0 ? <1-99> IP Standard access list number <1300-1999> IP Standard expanded access list number WORD Standard access-list name R3(config-router)#distance 255 1.1.1.1 0.0.0.0 1 R3(config-router)#^Z R3# *Mar 1 05:55:06.001: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 05:55:39.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3# *Mar 1 05:55:48.687: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.17.17.0 is directly connected, Tunnel0 C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11121] via 17.17.17.1, 00:00:57, Tunnel0 C 222.1.1.0/24 is directly connected, Loopback0 R 223.1.1.0/24 [120/1] via 208.28.1.1, 00:00:04, Serial1/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.193/32 [110/20] via 17.17.17.1, 00:00:57, Tunnel0 O E2 208.28.1.194/32 [110/20] via 17.17.17.1, 00:00:58, Tunnel0 O E2 208.28.1.128/27 [110/20] via 17.17.17.1, 00:00:58, Tunnel0 O E2 208.28.1.64/28 [110/20] via 17.17.17.1, 00:00:58, Tunnel0 C 208.28.1.0/29 is directly connected, Serial1/0 O E2 208.28.1.0/24 [110/20] via 17.17.17.1, 00:00:58, Tunnel0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 O E2 180.40.0.0/16 [110/20] via 17.17.17.1, 00:00:58, Tunnel0 O E2 180.40.7.64/27 [110/20] via 17.17.17.1, 00:00:58, Tunnel0 R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets O 17.17.17.0 [110/11112] via 17.80.1.1, 00:01:14, FastEthernet0/0 C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11122] via 17.80.1.1, 00:01:14, FastEthernet0/0 O E2 222.1.1.0/24 [110/20] via 17.80.1.1, 00:01:14, FastEthernet0/0 O E2 223.1.1.0/24 [110/20] via 17.80.1.1, 00:01:14, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.193/32 [110/20] via 17.80.1.1, 00:01:14, FastEthernet0/0 O E2 208.28.1.194/32 [110/20] via 17.80.1.1, 00:01:15, FastEthernet0/0 O E2 208.28.1.128/27 [110/20] via 17.80.1.1, 00:01:15, FastEthernet0/0 O E2 208.28.1.64/28 [110/20] via 17.80.1.1, 00:01:15, FastEthernet0/0 O E2 208.28.1.0/29 [110/20] via 17.80.1.1, 00:01:15, FastEthernet0/0 O E2 208.28.1.0/24 [110/20] via 17.80.1.1, 00:01:15, FastEthernet0/0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks O E2 180.40.7.0/27 [110/20] via 17.80.1.1, 00:01:07, FastEthernet0/0 O E2 180.40.0.0/16 [110/20] via 17.80.1.1, 00:01:16, FastEthernet0/0 O E2 180.40.7.64/27 [110/20] via 17.80.1.1, 00:01:16, FastEthernet0/0 R4#ping 223.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 223.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 64/65/68 ms R4# R4# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip proto Routing Protocol is "rip" Sending updates every 30 seconds, next due in 21 seconds Invalid after 180 seconds, hold down 0, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: rip, ospf 1 (internal) Neighbor(s): 208.28.1.3 208.28.1.1 Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial1/0 2 2 Serial1/2 2 2 Yes Prob4 Loopback0 2 2 Automatic network summarization is not in effect Maximum path: 3 Routing for Networks: 180.40.0.0 208.28.1.0 222.1.1.0 Routing Information Sources: Gateway Distance Last Update --More--   Gateway Distance Last Update 180.40.7.2 120 00:11:36 208.28.1.1 120 00:00:01 208.28.1.3 120 00:00:02 Distance: (default is 120) Routing Protocol is "ospf 1" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Router ID 3.3.3.3 It is an autonomous system boundary router Redistributing External Routes from, rip, includes subnets in redistribution Number of areas in this router is 1. 1 normal 0 stub 0 nssa Maximum path: 4 Routing for Networks: 17.0.0.0 0.255.255.255 area 0 Routing Information Sources: Gateway Distance Last Update 1.1.1.1 255 00:05:59 6.6.6.6 110 00:05:59 Distance: (default is 110) Address Wild mask Distance List --More--   Address Wild mask Distance List 1.1.1.1 0.0.0.0 255 1 R3#sh run | b ospf router ospf 1 router-id 3.3.3.3 log-adjacency-changes redistribute rip subnets network 17.0.0.0 0.255.255.255 area 0 distance 255 1.1.1.1 0.0.0.0 1 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 redistribute ospf 1 metric 3 match internal network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! no ip http server --More--  no ip http secure-server --More--  ! --More--  access-list 1 permit 223.1.1.0 --More--  ! --More--  ! --More--  ! --More--  ! --More--  ! --More--   R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Mar 1 05:54:05.655: %OSPF-5-ADJ R1#sh run | b ospf redistribute ospf 1 metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router ospf 1 router-id 1.1.1.1 log-adjacency-changes redistribute eigrp 100 subnets redistribute rip subnets network 17.0.0.0 0.255.255.255 area 0 distribute-list 2 in Tunnel0 ! router rip version 2 redistribute eigrp 100 metric 4 redistribute ospf 1 metric 3 match internal passive-interface Ethernet0/0 offset-list 1 out 3 network 208.28.1.0 network 223.1.1.0 maximum-paths 3 --More--   R1#sh run | b ospf    route router eigrp 100 redistribute rip metric 128 2000 255 1 1500 redistribute ospf 1 metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router ospf 1 router-id 1.1.1.1 log-adjacency-changes redistribute eigrp 100 subnets redistribute rip subnets network 17.0.0.0 0.255.255.255 area 0 distribute-list 2 in Tunnel0 ! router rip version 2 redistribute eigrp 100 metric 4 redistribute ospf 1 metric 3 match internal passive-interface Ethernet0/0 offset-list 1 out 3 network 208.28.1.0 --More--   network 223.1.1.0 maximum-paths 3 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 access-list 2 deny 222.1.1.0 access-list 2 permit any ! ! ! ! ! ! line con 0 exec-timeout 0 0 privilege level 15 logging synchronous line aux 0 line vty 0 4 --More--   R1# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#ping 222.1.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 222.1.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 64/64/68 ms S6# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.17.17.0 is directly connected, Tunnel0 C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11121] via 17.17.17.1, 00:14:49, Tunnel0 C 222.1.1.0/24 is directly connected, Loopback0 R 223.1.1.0/24 [120/1] via 208.28.1.1, 00:00:24, Serial1/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.193/32 [110/20] via 17.17.17.1, 00:14:49, Tunnel0 O E2 208.28.1.194/32 [110/20] via 17.17.17.1, 00:14:50, Tunnel0 O E2 208.28.1.128/27 [110/20] via 17.17.17.1, 00:14:50, Tunnel0 O E2 208.28.1.64/28 [110/20] via 17.17.17.1, 00:14:50, Tunnel0 C 208.28.1.0/29 is directly connected, Serial1/0 O E2 208.28.1.0/24 [110/20] via 17.17.17.1, 00:14:50, Tunnel0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 O E2 180.40.0.0/16 [110/20] via 17.17.17.1, 00:14:50, Tunnel0 O E2 180.40.7.64/27 [110/20] via 17.17.17.1, 00:14:50, Tunnel0 R3# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip rotue ^ % Invalid input detected at '^' marker. S6#sh ip rpout    oute Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets O 17.17.17.0 [110/11112] via 17.57.100.1, 00:16:09, Vlan16 O 17.80.1.0 [110/11113] via 17.57.100.1, 00:16:09, Vlan16 C 17.57.100.0 is directly connected, Vlan16 O E2 222.1.1.0/24 [110/20] via 17.57.100.1, 00:16:09, Vlan16 O E2 223.1.1.0/24 [110/20] via 17.57.100.1, 00:16:09, Vlan16 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.193/32 [110/20] via 17.57.100.1, 00:16:09, Vlan16 O E2 208.28.1.194/32 [110/20] via 17.57.100.1, 00:16:09, Vlan16 O E2 208.28.1.128/27 [110/20] via 17.57.100.1, 00:16:09, Vlan16 O E2 208.28.1.64/28 [110/20] via 17.57.100.1, 00:16:09, Vlan16 O E2 208.28.1.0/29 [110/20] via 17.57.100.1, 00:16:09, Vlan16 O E2 208.28.1.0/24 [110/20] via 17.57.100.1, 00:16:09, Vlan16 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks O E2 180.40.7.0/27 [110/20] via 17.57.100.1, 00:16:14, Vlan16 O E2 180.40.0.0/16 [110/20] via 17.57.100.1, 00:16:14, Vlan16 O E2 180.40.7.64/27 [110/20] via 17.57.100.1, 00:16:14, Vlan16 S6# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip o eigrp da  top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.66) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 208.28.1.193/32, 1 successors, FD is 409600, serno 18 via 208.28.1.65 (409600/128256), Ethernet0/0 P 208.28.1.194/32