=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.05.17 17:47:09 =~=~=~=~=~=~=~=~=~=~=~= R2# R2# R2# R2#sh run | b     int s 1/0.1 Building configuration... Current configuration : 111 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay interface-dlci 203 end R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0-.  .1 R2(config-subif)#no frame-relay interface-dlci 203 R2(config-subif)#fram map ip 208.28.1.2 203 R2(config-subif)#fram map ip 208.28.1.2 203 203 1 203 R2(config-subif)#do sh in    rn un int s 1/0.2 Building configuration... Current configuration : 112 bytes ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay interface-dlci 201 end R2(config-subif)#int s 1/0.2 R2(config-subif)#no frame-relay interface-dlci 201 R2(config-subif)#fram map ip 180.40.7.66 201 R2(config-subif)#^Z R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/0 Building configuration... Current configuration : 111 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon end R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#no fram inv R3(config-if)#no fram inverse-arp R3(config-if)#fram map ip 208.28.1.1 301 R3(config-if)#fram map ip 208.28.1.1 301 fram map ip 208.28.1.1 301 2 302 3 302 R3(config-if)#^Z R3#pinf *Mar 1 04:48:45.540: %SYS-5-CONFIG_I: Configured from console by console R3#pinf    208.28.1..1 % Unrecognized host or address, or protocol not running. R3#pin 208.28.1..11  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R3#pin 208.28.1.1 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1> R1>en R1#confi gt ^ % Invalid input detected at '^' marker. R1#sh run | b line line con 0 line aux 0 line vty 0 4 ! ! end R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int   line con 0 R1(config-line)#loggg syn ^ % Invalid input detected at '^' marker. R1(config-line)#loggg syn syn  R1(config-line)#no exec-tim R1(config-line)#exiut5 ^ % Invalid input detected at '^' marker. R1(config-line)#\zxdigfjadhgqads ^ % Invalid input detected at '^' marker. R1(config-line)#ew  no ip domain - loop ^ % Invalid input detected at '^' marker. R1(config-line)#no ip domain loopp  exit R1(config)#no ip dom R1(config)#no ip domain lo R1(config)#no ip domain lookup R1(config)#^Z R1#ping *Mar 1 04:50:55.101: %SYS-5-CONFIG_I: Configured from console by console R1#ping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/80/93 ms R1#ping 208.28.1.2 2 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/125/144 ms R1#sh int s 1/  0/0.1 Serial0/0.1 is up, line protocol is up Hardware is PowerQUICC Serial Internet address is 208.28.1.1/28 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#ip address % Incomplete command. R1(config-subif)#20ip address 208.28.1.1 255.255.25. 5.248 R1(config-subif)#^Z R1#config tsh int s 0/0.1 Serial0/0.1 is up, line protocol is up Hardware is PowerQUICC Serial Internet address is 208.28.1.1/29 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never R1# *Mar 1 04:52:26.318: %SYS-5-CONFIG_I: Configured from console by console R1#q config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router eigrp 100 R1(config-router)#net 208.28.1.66 0.0.0.0 R1(config-router)#net 180.40.7.66 0.0.0.0.0   R1(config-router)#nei R1(config-router)#neighbor 180.40.7.                   RACK10AS#5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#router eigrp 100 S5(config-router)#net 208.28.1.65 0.0.0.0 S5(config-router)#net 208.28.1.65 0.0.0.0 04:56:15: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.66 (Vlan10) is up: new adjacency S5(config-router)#net 208.28.1.65 0.0.0.0 0.0.0.0  0.0.0.0 1 0.0.0.03 0.0.0.00 0.0.0.0 S5(config-router)#^Z S5# RACK10AS#2 [Resuming connection 2 to r2 ... ] *Mar R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#rotuer      u uter eibgrp grp  % Incomplete command. R2(config)#router eigrp 100 R2(config-router)#net 208.28.1.129 0.0.0.0 R2(config-router)# *Mar 1 04:53:35.119: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 208.28.1.130 (FastEthernet0/1) is up: new adjacency R2(config-router)#net 180.40.7.65 0.0.0.0 R2(config-router)# *Mar 1 04:53:44.654: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is up: new adjacency R2(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 10 00:00:08 1 4500 1 0 0 208.28.1.130 Fa0/1 14 00:00:18 1166 5000 0 4 R2(config-router)# RACK10AS#1 [Resuming connection 1 to r1 ... ] *Mar R1(config-router)#do sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 208.28.1.65 Et0/0 13 00:01:05 1 200 0 3 R1(config-router)# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2(config-router)#do deb fram pack Frame Relay packet debugging is on R2(config-router)# *Mar 1 04:54:40.850: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2(config-router)# *Mar 1 04:54:44.168: Serial1/0.2(o): dlci 201(0x3091), pkt type 0x800(IP), datagramsize 72 *Mar 1 04:54:45.145: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2(config-router)#do deb fram packsh ip eigrp nei *Mar 1 04:54:49.168: Serial1/0.2(o): dlci 201(0x3091), pkt type 0x800(IP), datagramsize 72 *Mar 1 04:54:49.769: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2(config-router)#do sh ip eigrp neinet 180.40.7.65 0.0.0.0do sh ip eigrp nei  IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 10 00:01:09 1 5000 1 0 0 208.28.1.130 Fa0/1 10 00:01:18 1166 5000 0 4 R2(config-router)# *Mar 1 04:54:54.168: Serial1/0.2(o): dlci 201(0x3091), pkt type 0x800(IP), datagramsize 72 *Mar 1 04:54:54.321: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2(config-router)# *Mar 1 04:54:59.168: Serial1/0.2(o): dlci 201(0x3091), pkt type 0x800(IP), datagramsize 72 *Mar 1 04:54:59.237: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2(config-router)# *Mar 1 04:55:03.556: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 *Mar 1 04:55:04.169: Serial1/0.2: broadcast search *Mar 1 04:55:04.169: Serial1/0.2:encaps failed on broadcast for link 7(IP) R2(config-router)# *Mar 1 04:55:04.173: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is down: retry limit exceeded R2(config-router)#dp u a      *Mar 1 04:55:08.496: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 *Mar 1 04:55:08.496: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is up: new adjacency R2(config-router)#d *Mar 1 04:55:08.508: Serial1/0.2(o): dlci 201(0x3091), pkt type 0x800(IP), datagramsize 72 R2(config-router)#do au  u a *Mar 1 04:55:10.511: Serial1/0.2(o): dlci 201(0x3091), pkt type 0x800(IP), datagramsize 72 R2(config-router)#do u all All possible debugging has been turned off R2(config-router)# *Mar 1 04:55:13.095: Serial1/0(i): dlci 201(0x3091), pkt type 0x800, datagramsize 64 R2(config-router)#nei 180.40.7.66 ser 1/0.2 R2(config-router)#^Z R2# *Mar 1 04:55:34.282: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is down: Static peer configured *Mar 1 04:55:34.875: %SYS RACK10AS#1 [Resuming connection 1 to r1 ... ] R1(config-router)#neio 180. 180.  180.40.7.65 ser 0/0.2 R1(config-router)#^Z R1# *Mar 1 04:56:44.694: %SYS-5-CONFIG_I: Configured from console by console R1# RACK10AS#2 [Resuming connection 2 to r2 ... ] G_I: Configured from co R2#sh run int s 1/0.2 Building configuration... Current configuration : 116 bytes ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 end R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 12 00:01:44 1 5000 0 3 0 208.28.1.130 Fa0/1 14 00:04:04 1166 5000 0 4 R2# R2# R2# R2#sh ip eigrp nei IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 180.40.7.66 Se1/0.2 14 00:02:04 1 5000 0 3 0 208.28.1.130 Fa0/1 12 00:04:24 1166 5000 0 4 R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:05:04, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:02:16, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:04:59, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2#sh ip eigrp top all IP-EIGRP Topology Table for AS(100)/ID(208.28.1.129) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 208.28.1.128/27, 1 successors, FD is 28160, serno 1 via Connected, FastEthernet0/1 P 208.28.1.64/28, 1 successors, FD is 28416, serno 2 via 208.28.1.130 (28416/2816), FastEthernet0/1 P 180.40.0.0/16, 1 successors, FD is 2172672, serno 6 via Summary (20512000/0), Null0 via 208.28.1.130 (2172672/2170112), FastEthernet0/1 P 208.28.1.0/24, 1 successors, FD is 28160, serno 5 via Summary (28160/0), Null0 via 180.40.7.66 (20537600/281600), Serial1/0.2 P 180.40.7.64/27, 1 successors, FD is 20512000, serno 4 via Connected, Serial1/0.2 R2# R2# R2# R2#ping 208.28.1.66 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R2#ping 208.28.1.66 5 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms R2# RACK10AS#1 [Resuming connection 1 to r1 ... ] * R1#sh run | b router router eigrp 100 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! no ip http server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! --More--   R1# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#sh run | b router router eigrp 100 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous --More--   R2# RACK10AS#5 [Resuming connection 5 to r5 ... ] 04:5 S5#shb run        run | b router router eigrp 100 network 208.28.1.65 0.0.0.0 network 208.28.1.130 0.0.0.0 auto-summary ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 no login line vty 5 15 no login ! ! --More--   S5# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer       iou   outer rip R3(config-router)#no auto R3(config-router)#ver 2 R3(config-router)#net 208.28.1.0 R3(config-router)#net 180.40.0.0 R3(config-router)#nei 180.40.       208.28.1.1 R3(config-router)#nei 208.28.1.1 3 R3(config-router)#nei 208.28.1.3 ? R3(config-router)#nei 208.28.1.3                ^Z R3# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1#confi gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#rotuer      uter eip   rip R1(config-router)#ver 2 R1(config-router)#no auto R1(config-router)#net     pass e 0/0 R1(config-router)#net 208.28.1.1 0 R1(config-router)#. ^Z R1# *Mar 1 05:05:05.302: %SYS-5-CONFIG_I: Configured from console by console RACK10AS#2\ ^ % Invalid input detected at '^' marker. RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#routeer    r rip R2(config-router)#ver 2 R2(config-router)#no auto R2(config-router)#net     pass s1/0.2 R2(config-router)#pass s1/0.2      fa 0/1 R2(config-router)#net 208.28.1.0 R2(config-router)#net 180.40.0.0 R2(config-router)#nei 208. % Incomplete command. R2(config-router)#nei 208.28.1.25 R2(config-router)#nei 208.28.1.25  R2(config-router)#nei 208.28.1.25nnei 208.28.1.25onei 208.28.1.25 nei 208.28.1.25 R2(config-router)#^Z R2# *Mar 1 05:05:01.035: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks C 208.28.1.128/27 is directly connected, FastEthernet0/1 D 208.28.1.64/28 [90/28416] via 208.28.1.130, 00:11:30, FastEthernet0/1 C 208.28.1.0/29 is directly connected, Serial1/0.1 D 208.28.1.0/24 is a summary, 00:08:42, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 D 180.40.0.0/16 is a summary, 00:11:26, Null0 C 180.40.7.64/27 is directly connected, Serial1/0.2 R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] * R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:05, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:19, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.0 is directly connected, Serial1/2 R 180.40.7.64 [120/1] via 180.40.7.2, 00:00:05, Serial1/2 R3# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1#confi gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#roteur      uter rip R1(config-router)#redis R1(config-router)#redistribute eigrp 100 met R1(config-router)#redistribute eigrp 100 metric 2 R1(config-router)#router eigrp 100 R1(config-router)#\ redis R1(config-router)#redistribute rip meop   R1(config-router)#redistribute rip metric 120 8000   2        ? <1-4294967295> Bandwidth metric in Kbits per second R1(config-router)#redistribute rip metric 128 2000    ? <0-4294967295> EIGRP delay metric, in 10 microsecond units R1(config-router)#redistribute rip metric 128 2000 255 1 1500 R1(config-router)#^Z R1# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#routeer    t  r   r   er rip R2(config-router)#redistribute rip metric 128 2000 255 1 1500 ^ % Invalid input detected at '^' marker. R2(config-router)#redistribute rip metric 128 2000 255 1 1500 redis eigrp 100 met 3 2 R2(config-router)#router eigrp 100 R2(config-router)#router eigrp 100edis eigrp 100 met 2tribute rip metric 128 2000 255 1 1500 R2(config-router)#^Z R2#sh ip prot *Mar 1 05:10:26.356: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip proto Routing Protocol is "eigrp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates Default networks accepted from incoming updates EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0 EIGRP maximum hopcount 100 EIGRP maximum metric variance 1 Redistributing: eigrp 100, rip EIGRP NSF-aware route hold timer is 240s Automatic network summarization is in effect Automatic address summarization: 208.28.1.0/24 for Serial1/0.2 Summarizing with metric 28160 180.40.0.0/16 for FastEthernet0/1 Summarizing with metric 20512000 Maximum path: 4 Routing for Networks: 180.40.7.65/32 208.28.1.129/32 Routing Information Sources: Gateway Distance Last Update (this router) 90 00:14:03 --More--   Gateway Distance Last Update 208.28.1.130 90 00:00:12 180.40.7.66 90 00:00:12 Distance: internal 90 external 170 Routing Protocol is "rip" Sending updates every 30 seconds, next due in 13 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: eigrp 100, rip Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial1/0.1 2 2 Serial1/2 2 2 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 180.40.0.0 208.28.1.0 Passive Interface(s): FastEthernet0/1 Serial1/0.2 --More--   Routing Information Sources: Gateway Distance Last Update 180.40.7.3 120 00:00:07 208.28.1.2 120 00:00:12 Distance: (default is 120) R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 4 subnets, 4 masks R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:28, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:10, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:10, Serial1/0 [120/2] via 180.40.7.2, 00:00:28, Serial1/2 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:11, Serial1/0 [120/2] via 180.40.7.2, 00:00:00, Serial1/2 R 180.40.7.64/27 [120/1] via 180.40.7.2, 00:00:00, Serial1/2 R3# RACK10AS#5 [Resuming connection 5 to r5 ... ] S5#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 208.28.1.0/24 is variably subnetted, 3 subnets, 3 masks C 208.28.1.128/27 is directly connected, Vlan20 C 208.28.1.64/28 is directly connected, Vlan10 D EX 208.28.1.0/29 [170/20512256] via 208.28.1.129, 00:01:01, Vlan20 [170/20512256] via 208.28.1.66, 00:01:01, Vlan10 D 180.40.0.0/16 [90/2170112] via 208.28.1.66, 00:17:45, Vlan10 S5# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#ping 208.28.1.65 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.65, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R3#ping 208.28.1.65  130 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/44/44 ms R3# RACK10AS#2 1 [Resuming connection 1 to r1 ... ] *M R1#sh run  | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 2 passive-interface Ethernet0/0 network 208.28.1.0 no auto-summary ! no ip http server ip classless ! ! ! ! ! ! ! --More--   R1# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#sh run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 2 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 network 180.40.0.0 network 208.28.1.0 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! --More--   R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#sh run | b ver   router router rip version 2 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! line con 0 --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#key R3(config)#key ch R3(config)#key chain Prob4 R3(config-keychain)#key 1 R3(config-keychain-key)#key cisco ^ % Invalid input detected at '^' marker. R3(config-keychain-key)#key ciscoo       R3(config-keychain-key)#key-string cisco R3(config-keychain-key)#int s 1/2 R3(config-if)#shut R3(config-if)# *Mar 1 05:22:01.003: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 05:22:02.005: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#ip authen ? key-chain key-chain mode mode R3(config-if)#ip authen key R3(config-if)#ip authen key-chain ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) R3(config-if)#ip authen key-chain                  rip ? advertise Specify update interval authentication Authentication control receive advertisement reception send advertisement transmission triggered enable rfc2091 triggered rip v2-broadcast send ip broadcast v2 update R3(config-if)#ip rip authen ? key-chain Authentication key-chain mode Authentication mode R3(config-if)#ip rip authen key R3(config-if)#ip rip authen key-chain ? LINE name of key-chain R3(config-if)#ip rip authen key-chain p ro  Prob4 R3(config-if)#ip rip authe R3(config-if)#ip rip authentication , R3(config-if)#ip rip authentication ,  m   R3(config-if)#ip rip authentication m R3(config-if)#ip rip authentication mode ? md5 Keyed message digest text Clear text authentication R3(config-if)#ip rip authentication mode , m R3(config-if)#ip rip authentication mode md5 ? R3(config-if)#ip rip authentication mode md5 R3(config-if)# RACK10AS#2 [Resuming connection 2 to r2 ... ] *Mar R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#key cha R2(config)#key chain Prob4 R2(config-keychain)#key 1 R2(config-keychain-key)#ke R2(config-keychain-key)#key-string cisco R2(config-keychain-key)#int s 1/2 R2(config-if)#ip a roip   ip % Incomplete command. R2(config-if)#ip rip authen m m R2(config-if)#ip a rip authe k R2(config-if)#ip rip authe key-chain Prob4 R2(config-if)#^Z R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3(config-if)#do deb ip rip RIP protocol debugging is on R3(config-if)#no shut R3(config-if)# *Mar 1 05:24:53.458: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:24:53.462: RIP: sending request on Serial1/2 to 224.0.0.9 *Mar 1 05:24:53.462: RIP: sending request on Serial1/2 to 224.0.0.9 *Mar 1 05:24:53.534: RIP: received packet with MD5 authentication *Mar 1 05:24:53.534: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 05:24:53.538: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 05:24:53.538: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 05:24:53.538: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 05:24:53.538: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 05:24:53.538: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 05:24:53.542: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 05:24:53.562: RIP: received packet with MD5 authentication *Mar 1 05:24:53.562: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 05:24:53.562: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 05:24:53.562: 180.40.7.6 R3(config-if)#4/27 via 0.0.0.0 in 1 hops *Mar 1 05:24:53.562: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 05:24:53.562: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 05:24:53.566: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 05:24:53.566: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 05:24:53.574: RIP: received packet with MD5 authentication *Mar 1 05:24:53.574: RIP: received v2 request from 180.40.7.2 on Serial1/2 *Mar 1 05:24:53.574: RIP: sending update with long TTL *Mar 1 05:24:53.574: RIP: sending v2 update to 180.40.7.2 via Serial1/2 (180.40.7.3) *Mar 1 05:24:53.574: RIP: build update entries *Mar 1 05:24:53.574: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:24:53.578: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:24:53.586: RIP: received packet with MD5 authentication *Mar 1 05:24:53.586: RIP: received v2 request from 180.40.7.2 on Serial1/2 *Mar 1 05:24:53.586: RIP: sending update with long TTL *Mar 1 05:24:53.586: RIP: sending v2 update to 180.40.7.2 via Serial1/2 (180.40.7.3) *Mar 1 05:24:53.586: RIP: build update entries *Mar 1 05:24:53.590: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:24:53.590: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:24:54.459: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up *Mar 1 05:24:55.461: RIP: sending v2 flash update to 224.0.0.9 via Serial1/0 (208.28.1.2) *Mar 1 05:24:55.461: RIP: build flash update entries *Mar 1 05:24:55.461: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:24:55.461: 180.40.7.64/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:24:55.461: 208.28.1.128/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:24:55.461: RIP: sending v2 flash update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 05:24:55.461: RIP: build flash update entries *Mar 1 05:24:55.465: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:24:55.465: 180.40.7.64/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:24:55.465: 208.28.1.128/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:24:55.465: RIP: sending v2 flash update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 05:24:55.465: RIP: build flash update entries *Mar 1 05:24:55.465: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:24:55.465: 180.40.7.64/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:24:55.469: 208.28.1.128/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:24:55.469: RIP: sending v2 flash update to 224.0.0.9 via Serial1/2 (180.40.7.3) *Mar 1 05:24:55.469: RIP: build flash update entries - suppressing null update R3(config-if)# R3(config-if)# *Mar 1 05:25:09.428: RIP: received v2 update from 208.28.1.1 on Serial1/0 *Mar 1 05:25:09.428: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 05:25:09.428: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 05:25:09.428: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 05:25:09.428: 208.28.1.64/28 via 0.0.0.0 in 1 hops *Mar 1 05:25:09.432: 208.28.1.128/27 via 0.0.0.0 in 2 hops R3(config-if)#^Z R3# *Mar 1 05:25:11.311: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 05:25:15.810: RIP: sending v2 update to 224.0.0.9 via Serial1/0 (208.28.1.2) *Mar 1 05:25:15.810: RIP: build update entries *Mar 1 05:25:15.810: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:25:15.810: 180.40.7.64/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:25:15.810: 208.28.1.128/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:25:15.810: RIP: sending v2 update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 05:25:15.810: RIP: build update entries *Mar 1 05:25:15.814: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:25:15.814: 180.40.7.64/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:25:15.814: 208.28.1.128/27 via 0.0.0.0, metric 2, tag 0 R3# *Mar 1 05:25:15.814: RIP: sending v2 update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 05:25:15.814: RIP: build update entries *Mar 1 05:25:15.814: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:25:15.814: 180.40.7.64/27 via 0.0.0.0, metric 2, tag 0 *Mar 1 05:25:15.818: 208.28.1.128/27 via 0.0.0.0, metric 2, tag 0 R3# *Mar 1 05:25:19.376: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.3) *Mar 1 05:25:19.376: RIP: build update entries *Mar 1 05:25:19.376: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:25:19.376: 208.28.1.64/28 via 0.0.0.0, metric 2, tag 0 R3# *Mar 1 05:25:23.403: RIP: received packet with MD5 authentication *Mar 1 05:25:23.403: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 05:25:23.403: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 05:25:23.407: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 05:25:23.407: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 05:25:23.407: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 05:25:23.407: 208.28.1.64/28 via 0.0.0.0 in 2 hops *Mar 1 05:25:23.407: 208.28.1.128/27 via 0.0.0.0 in 1 hops R3#ui    all All possible debugging has been turned off R3# RACK10AS#2 [Resuming connection 2 to r2 ... ] * R2#sh run | b key key chain Prob4 key 1 key-string cisco ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 ! --More--  interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 frame-relay map ip 180.40.7.66 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip rip authentication mode md5 ip rip authentication key-chain Prob4 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 --More--   R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#sh runb    | b            cl ip    ip c ? % Ambiguous command: "cl ip c " R3#cl ip c  ? % Ambiguous command: "cl ip c" R3#cl ip c     ea ip ? access-list Clear access list statistical information access-template Access-template accounting Clear IP accounting database arp IP ARP table audit Clear IDS information auth-proxy Clear the auth-proxy info bgp Clear BGP connections cache Delete cache table entries cef Cisco Express Forwarding info cgmp Cisco Group Management Protocol (CGMP) dhcp Delete items from the DHCP database director Clear director information drp Clear director responder counters dvmrp DVMRP eigrp Clear IP-EIGRP flow Clear flow information http Clear HTTP parameters igmp IGMP clear commands mobile IP Mobility mrm IP Multicast Routing Monitor clear commands mroute Delete multicast route table entries msdp Multicast Source Discovery Protocol (MSDP) --More--   R3#clea ip cef ? * clear stats for all cisco express forwarding entries A.B.C.D prefix of entry whose stats are to be cleared epoch Begin new CEF table epoch event-log Clear table event log statistics and records inconsistency Clear inconsistency checker statistics and records R3#clea ip cef             sh run | b rout    key key chain Prob4 key 1 key-string cisco ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 --More--   no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown --More--   R3# RACK10AS#5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int lo 0 S5(config-if)#ip add 208.28.1 05:31:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up S5(config-if)#ip add 208.28.1.193 255.255.205552352552525              55.255 S5(config-if)#ip add 208.28.1.193 255.255.255.255nt lo 0  1 S5(config-if)#int lo 1 05:31:52: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up S5(config-if)#int lo 1p add 208.28.1.193 255.255.255.2553 255.255.255.255 4 255.255.255.255 S5(config-if)#router eigrp 100 S5(config-router)#net 208.28.1.193 0.0.0.0.3   S5(config-router)#net 208.28.1.193 0.0.0.0 0.0.0.0 4 0.0.0.0 S5(config-router)# S5(config-router)# S5(config-router)# S5(config-router)#^Z S5# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#redi  eigrp 100 met 4 R2(config-router)#exity ^ % Invalid input detected at '^' marker. R2(config-router)#exit R2(config)#access-list a 1 per 208.28.1.193 R2(config)#router rip R2(config-router)#off R2(config-router)#offset-list 1 ? in Perform offset on incoming updates out Perform offset on outgoing updates R2(config-router)#offset-list 1 out ? <0-16> Offset R2(config-router)#offset-list 1 out 3 R2(config-router)#^Z R2# *Mar 1 05:30:26.564: %SYS-5-CONFIG_I: Configured from console by console R2#deb ip riup  p RIP protocol debugging is on R2# *Mar 1 05:30:34.441: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 05:30:34.441: RIP: build update entries *Mar 1 05:30:34.441: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:30:34.441: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:30:34.441: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:30:34.441: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:30:34.441: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:30:34.445: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:30:34.445: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 05:30:34.445: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2#u all All possible debugging has been turned off R2#^Z R2# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#rotuer rip        uter rip R1(config-router)#def R1(config-router)#default- R1(config-router)#default-m, R1(config-router)#default-m,    m R1(config-router)#default maximum-paths                -me R1(config-router)#default-metric 2 R1(config-router)#exit R1(config)#access-list 1 per 1 208.28.1.193 R1(config)#access-list 1 per 208.28.1.193 4 per 208.28.1.194 1 per 208.28.1.194 R1(config)#access-list 1 per 208.28.1.194 per 208.28.1.194 2 per 208.28.1.194 R1(config)#ip access-list access-list 2 per 208.28.1.194ip access-list access-list 2 per 208.28.1.1941 per 208.28.1.194naccess-list 1 per 208.28.1.194oaccess-list 1 per 208.28.1.194 access-list 1 per 208.28.1.194 R1(config)#no access-list 1 per 208.28.1.194access-list 2 per 208.28.1.194 1 per 208.28.1.1943exit access-list 1 per 208.28.1.193 R1(config)#reo   route-map Prob5b R1(config-route-map)#match 1 ip add 1 R1(config-route-map)#set met 7 R1(config-route-map)#set met 7match ip add 1route-map Prob5b 20 R1(config-route-map)#route-map Prob5b 20set met 7 match ip add 1 2 R1(config-route-map)#match ip add 2route-map Prob5b 20set met 7  4 R1(config-route-map)#set met 4match ip add 2route-map Prob5b 20  30 R1(config-route-map)#router rip R1(config-router)#red eigrp 100 rout R1(config-router)#red eigrp 100 route-map Prob5b ? metric Metric for redistributed routes R1(config-router)#red eigrp 100 route-map Prob5b R1(config-router)#^Z R1# *Mar 1 05:34:18.545: %SYS-5-CONFIG_I: Configured from console by console R1# R1# R1# R1# R1# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#shp  ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.1, 00:00:21, Serial1/0 [120/7] via 180.40.7.2, 00:00:13, Serial1/2 R 208.28.1.194/32 [120/4] via 208.28.1.1, 00:00:21, Serial1/0 [120/4] via 180.40.7.2, 00:00:13, Serial1/2 R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:13, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:25, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:25, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 --More--  R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:03, Serial1/0 R 180.40.7.64/27 [120/1] via 180.40.7.2, 00:00:21, Serial1/2 R3# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#deb ip rip RIP protocol debugging is on R2# *Mar 1 05:34:18.256: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 05:34:18.256: RIP: build update entries *Mar 1 05:34:18.256: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:34:18.256: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:34:18.256: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:34:18.256: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:34:18.256: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:34:18.260: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:34:18.260: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 05:34:18.260: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2# *Mar 1 05:34:31.289: RIP: received packet with MD5 authentication *Mar 1 05:34:31.289: RIP: received v2 update from 180.40.7.3 on Serial1/2 *Mar 1 05:34:31.289: 180.40.0.0/16 via 0.0.0.0 in 3 hops *Mar 1 05:34:31.289: 208.28.1.0/24 via 0.0.0.0 in 3 hops *Mar 1 05:34:31.289: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 05:34:31.289: 208.28.1.64/28 via 0.0.0.0 in 2 hops R2# *Mar 1 05:34:36.209: RIP: received v2 update from 208.28.1.2 on Serial1/0.1 *Mar 1 05:34:36.209: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 05:34:36.209: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 05:34:36.213: 208.28.1.128/27 via 0.0.0.0 in 2 hops R2# *Mar 1 05:34:40.248: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 05:34:40.248: RIP: build update entries *Mar 1 05:34:40.248: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:34:40.248: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:34:40.248: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:34:40.248: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:34:40.248: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:34:40.252: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:34:40.252: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 05:34:40.252: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2# *Mar 1 05:34:48.085: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 05:34:48.085: RIP: build update entries *Mar 1 05:34:48.085: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:34:48.085: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:34:48.085: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:34:48.085: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:34:48.085: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:34:48.089: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:34:48.089: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 05:34:48.089: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2#u all All possible debugging has been turned off R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.1, 00:00:24, Serial1/0 [120/7] via 180.40.7.2, 00:00:11, Serial1/2 R 208.28.1.194/32 [120/4] via 208.28.1.1, 00:00:24, Serial1/0 [120/4] via 180.40.7.2, 00:00:11, Serial1/2 R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:11, Serial1/2 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:25, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:25, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 --More--   R3#sh ip rip data 180.40.0.0/16 auto-summary 180.40.0.0/16 [2] via 208.28.1.1, 00:00:07, Serial1/0 180.40.7.0/27 directly connected, Serial1/2 180.40.7.64/27 [1] via 180.40.7.2, 00:00:22, Serial1/2 208.28.1.0/24 auto-summary 208.28.1.0/24 [2] via 208.28.1.1, 00:00:07, Serial1/0 208.28.1.0/29 directly connected, Serial1/0 208.28.1.64/28 [1] via 208.28.1.1, 00:00:07, Serial1/0 208.28.1.128/27 [1] via 180.40.7.2, 00:00:22, Serial1/2 208.28.1.193/32 [7] via 180.40.7.2, 00:00:22, Serial1/2 [7] via 208.28.1.1, 00:00:07, Serial1/0 208.28.1.194/32 [4] via 180.40.7.2, 00:00:22, Serial1/2 [4] via 208.28.1.1, 00:00:07, Serial1/0 R3#sh ip     deb ip rip RIP protocol debugging is on R3#u all All possible debugging has been turned off R3# *Mar 1 05:35:40.947: RIP: received packet with MD5 authentication *Mar 1 05:35:40.947: RIP: received v2 update from 180.40.7.2 on Serial1/2 *Mar 1 05:35:40.947: 180.40.0.0/16 via 0.0.0.0 in 4 hops *Mar 1 05:35:40.951: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 05:35:40.951: 208.28.1.0/24 via 0.0.0.0 in 4 hops *Mar 1 05:35:40.951: 208.28.1.0/29 via 0.0.0.0 in 1 hops *Mar 1 05:35:40.951: 208.28.1.64/28 via 0.0.0.0 in 4 hops *Mar 1 05:35:40.951: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 05:35:40.951: 208.28.1.193/32 via 0.0.0.0 in 7 hops *Mar 1 05:35:40.955: 208.28.1.194/32 via 0.0.0.0 in 4 hops R3# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#deb ip rip RIP protocol debugging is on R2# *Mar 1 05:37:01.335: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 05:37:01.335: RIP: build update entries *Mar 1 05:37:01.335: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:37:01.335: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:37:01.335: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:37:01.335: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:37:01.335: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:37:01.339: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:37:01.339: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 05:37:01.339: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2#u all All possible debugging has been turned off R2# *Mar 1 05:37:08.935: RIP: sending v2 update to 224.0.0.9 via Serial1/2 (180.40.7.2) *Mar 1 05:37:08.935: RIP: build update entries *Mar 1 05:37:08.935: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:37:08.935: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:37:08.935: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:37:08.935: 208.28.1.0/29 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:37:08.935: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:37:08.939: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:37:08.939: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 05:37:08.939: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#nei 208.28.1.2 R2(config-router)#nei 208.28.1.2 2 3nnei 208.28.1.3onei 208.28.1.3 nei 208.28.1.3 R2(config-router)#^Z R2# *Mar 1 05:37:48.552: %SYS-5-CONFIG_I: Configured from console by console R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#u alldeb ip rip RIP protocol debugging is on R3#u all All possible debugging has been turned off R3# *Mar 1 05:37:53.997: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 05:37:53.997: 180.40.0.0/16 via 0.0.0.0 in 4 hops *Mar 1 05:37:53.997: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 05:37:53.997: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 05:37:53.997: 208.28.1.0/24 via 0.0.0.0 in 4 hops *Mar 1 05:37:53.997: 208.28.1.64/28 via 0.0.0.0 in 4 hops *Mar 1 05:37:54.001: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 05:37:54.001: 208.28.1.193/32 via 0.0.0.0 in 7 hops *Mar 1 05:37:54.001: 208.28.1.194/32 via 0.0.0.0 in 4 hops R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.1, 00:00:15, Serial1/0 [120/7] via 180.40.7.2, 00:00:20, Serial1/2 [120/7] via 208.28.1.3, 00:00:02, Serial1/0 R 208.28.1.194/32 [120/4] via 208.28.1.1, 00:00:15, Serial1/0 [120/4] via 180.40.7.2, 00:00:20, Serial1/2 [120/4] via 208.28.1.3, 00:00:03, Serial1/0 R 208.28.1.128/27 [120/1] via 180.40.7.2, 00:00:21, Serial1/2 [120/1] via 208.28.1.3, 00:00:03, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:17, Serial1/0 C 208.28.1.0/29 is directly connected, Serial1/0 --More--  R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:18, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:18, Serial1/0 R 180.40.7.64/27 [120/1] via 180.40.7.2, 00:00:22, Serial1/2 [120/1] via 208.28.1.3, 00:00:04, Serial1/0 R3# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1#sh urn |     run | b router router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router rip version 2 redistribute eigrp 100 metric 2 route-map Prob5b passive-interface Ethernet0/0 network 208.28.1.0 default-metric 2 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.194 ! route-map Prob5b permit 10 --More--   match ip address 1 set metric 7 ! route-map Prob5b permit 20 match ip address 2 set metric 4 ! route-map Prob5b permit 30 ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! end R1# R1# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#sh run | b router rip router rip version 2 redistribute eigrp 100 metric 4 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 offset-list 1 out 3 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! access-list 1 permit 208.28.1.193 ! ! ! ! ! ! --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#ip rip tr R2(config-if)#ip rip triggered ? R2(config-if)#ip rip triggered R2(config-if)#^Z R2# *Mar 1 05:41:31.923: %SYS-5-CONFIG_I: Configured from console by consol RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/3 2 R3(config-if)#ip rip ? advertise Specify update interval authentication Authentication control receive advertisement reception send advertisement transmission triggered enable rfc2091 triggered rip v2-broadcast send ip broadcast v2 update R3(config-if)#ip rip triggered R3(config-if)#^Z R3# *Mar 1 05:41:56.270: %SYS-5-CONFIG_I: Configured from console by console R3# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#sh run        deb ip rip RIP protocol debugging is on R2# *Mar 1 05:42:28.467: RIP: received v2 update from 208.28.1.2 on Serial1/0.1 *Mar 1 05:42:28.467: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 05:42:29.509: RIP: sending v2 update to 224.0.0.9 via Serial1/0.1 (208.28.1.3) *Mar 1 05:42:29.509: RIP: build update entries *Mar 1 05:42:29.509: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:42:29.509: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:42:29.509: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:42:29.509: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:42:29.509: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:42:29.513: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:42:29.513: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 05:42:29.513: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2# *Mar 1 05:42:29.513: RIP: sending v2 update to 208.28.1.2 via Serial1/0.1 (208.28.1.3) *Mar 1 05:42:29.513: RIP: build update entries *Mar 1 05:42:29.513: 180.40.0.0/16 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:42:29.513: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:42:29.517: 180.40.7.64/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:42:29.517: 208.28.1.0/24 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:42:29.517: 208.28.1.64/28 via 0.0.0.0, metric 4, tag 0 *Mar 1 05:42:29.517: 208.28.1.128/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:42:29.517: 208.28.1.193/32 via 0.0.0.0, metric 7, tag 0 *Mar 1 05:42:29.517: 208.28.1.194/32 via 0.0.0.0, metric 4, tag 0 R2#u all All possible debugging has been turned off R2#sh run int s 1/2 Building configuration... Current configuration : 173 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 clock rate 64000 end R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1? / R3#sh run int s 12 /2 Building configuration... Current configuration : 155 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 end R3# R3# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router rip R2(config-router)#? Router configuration commands: address-family Enter Address Family command mode auto-summary Enable automatic network number summarization default Set a command to its defaults default-information Control distribution of default information default-metric Set metric of redistributed routes distance Define an administrative distance distribute-list Filter networks in routing updates exit Exit from routing protocol configuration mode flash-update-threshold Specify flash update threshold in second help Description of the interactive help system input-queue Specify input queue depth maximum-paths Forward packets over multiple paths neighbor Specify a neighbor router network Enable routing on an IP network no Negate a command or set its defaults offset-list Add or subtract offset from RIP metrics output-delay Interpacket delay for RIP updates passive-interface Suppress routing updates on an interface redistribute Redistribute information from another routing protocol timers Adjust routing timers --More--   traffic-share How to compute traffic share over alternate paths validate-update-source Perform sanity checks against source address of routing updates version Set routing protocol version R2(config-router)#tim,    ? basic Basic routing protocol update timers R2(config-router)#tim bas ? <0-4294967295> Interval between updates R2(config-router)#tim bas         output-delay ? <8-50> Delay in milliseconds R2(config-router)#output-delay 10 R2(config-router)#^Z R2#sh run | *Mar 1 05:45:08.814: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b rotuer R2#sh run | b rotuer    uter router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.65 0.0.0.0 network 208.28.1.129 0.0.0.0 neighbor 180.40.7.66 Serial1/0.2 auto-summary ! router rip version 2 timers basic 30 180 0 240 redistribute eigrp 100 metric 4 passive-interface FastEthernet0/1 passive-interface Serial1/0.2 output-delay 10 offset-list 1 out 3 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.2 no auto-summary ! ip classless ! no ip http server --More--   R2# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int     orouter         int s 1/2         router rip R3(config-router)#? Router configuration commands: address-family Enter Address Family command mode auto-summary Enable automatic network number summarization default Set a command to its defaults default-information Control distribution of default information default-metric Set metric of redistributed routes distance Define an administrative distance distribute-list Filter networks in routing updates exit Exit from routing protocol configuration mode flash-update-threshold Specify flash update threshold in second help Description of the interactive help system input-queue Specify input queue depth maximum-paths Forward packets over multiple paths neighbor Specify a neighbor router network Enable routing on an IP network no Negate a command or set its defaults offset-list Add or subtract offset from RIP metrics output-delay Interpacket delay for RIP updates passive-interface Suppress routing updates on an interface redistribute Redistribute information from another routing protocol timers Adjust routing timers --More--   traffic-share How to compute traffic share over alternate paths validate-update-source Perform sanity checks against source address of routing updates version Set routing protocol version R3(config-router)#no validate-update-source R3(config-router)#^Z R3# *Mar 1 05:46:29.506: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b router router rip version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer      uter rip R3(config-router)#mac x R3(config-router)#maximum-paths 3 R3(config-router)#^Z R3# *Mar 1 05:47:17.505: %SYS-5-CONFIG_I: Configured from console by console R3# RACK10AS#2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#rotuer      uter rip R2(config-router)#maximum-paths 3 R2(config-router)#^Z R2# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router eip   rip R1(config-router)#maximum-paths 3 R1(config-router)#^Z R1# *Mar 1 05:48:40.518: %SYS-5-CONFIG_I: Configured from console by console R1#sh run |         RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer      uter rip R3(config-router)#pass R3(config-router)#passive-interface s 1/0 R3(config-router)#do deb ip rip RIP protocol debugging is on R3(config-router)# *Mar 1 05:49:26.745: RIP: sending v2 update to 208.28.1.3 via Serial1/0 (208.28.1.2) *Mar 1 05:49:26.745: RIP: build update entries *Mar 1 05:49:26.745: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:49:26.749: RIP: sending v2 update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 05:49:26.753: RIP: build update entries *Mar 1 05:49:26.753: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 R3(config-router)# *Mar 1 05:49:27.867: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 05:49:27.867: 180.40.0.0/16 via 0.0.0.0 in 4 hops *Mar 1 05:49:27.867: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 05:49:27.867: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 05:49:27.871: 208.28.1.0/24 via 0.0.0.0 in 4 hops *Mar 1 05:49:27.871: 208.28.1.64/28 via 0.0.0.0 in 4 hops *Mar 1 05:49:27.871: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 05:49:27.871: 208.28.1.193/32 via 0.0.0.0 in 7 hops *Mar 1 05:49:27.871: 208.28.1.194/32 via 0.0.0.0 in 4 hops R3(config-router)# *Mar 1 05:49:37.390: RIP: received v2 update from 208.28.1.1 on Serial1/0 *Mar 1 05:49:37.390: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 05:49:37.390: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 05:49:37.390: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 05:49:37.390: 208.28.1.64/28 via 0.0.0.0 in 1 hops *Mar 1 05:49:37.394: 208.28.1.128/27 via 0.0.0.0 in 2 hops *Mar 1 05:49:37.394: 208.28.1.193/32 via 0.0.0.0 in 7 hops *Mar 1 05:49:37.394: 208.28.1.194/32 via 0.0.0.0 in 4 hops R3(config-router)# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/1 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D 208.28.1.193/32 [90/409600] via 208.28.1.65, 00:20:58, Ethernet0/0 D 208.28.1.194/32 [90/409600] via 208.28.1.65, 00:20:55, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 00:56:51, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:53:30, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:01, Serial0/0.1 D 180.40.0.0/16 is a summary, 00:57:38, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# RACK10AS#3 [Resuming connection 3 to r3 ... ] *Mar 1 05 R3(config-router)# *Mar 1 05:50:24.419: RIP: received v2 update from 208.28.1.3 on Serial1/0 *Mar 1 05:50:24.419: 180.40.0.0/16 via 0.0.0.0 in 4 hops *Mar 1 05:50:24.419: 180.40.7.0/27 via 0.0.0.0 in 1 hops *Mar 1 05:50:24.419: 180.40.7.64/27 via 0.0.0.0 in 1 hops *Mar 1 05:50:24.423: 208.28.1.0/24 via 0.0.0.0 in 4 hops *Mar 1 05:50:24.423: 208.28.1.64/28 via 0.0.0.0 in 4 hops *Mar 1 05:50:24.423: 208.28.1.128/27 via 0.0.0.0 in 1 hops *Mar 1 05:50:24.423: 208.28.1.193/32 via 0.0.0.0 in 7 hops *Mar 1 05:50:24.423: 208.28.1.194/32 via 0.0.0.0 in 4 hops *Mar 1 05:50:24.540: RIP: sending v2 update to 208.28.1.3 via Serial1/0 (208.28.1.2) R3(config-router)# *Mar 1 05:50:24.540: RIP: build update entries *Mar 1 05:50:24.540: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 *Mar 1 05:50:24.540: RIP: sending v2 update to 208.28.1.1 via Serial1/0 (208.28.1.2) *Mar 1 05:50:24.540: RIP: build update entries *Mar 1 05:50:24.540: 180.40.7.0/27 via 0.0.0.0, metric 1, tag 0 R3(config-router)#do u all All possible debugging has been turned off R3(config-router)# *Mar 1 05:50:29.115: RIP: received v2 update from 208.28.1.1 on Serial1/0 *Mar 1 05:50:29.115: 180.40.0.0/16 via 0.0.0.0 in 2 hops *Mar 1 05:50:29.115: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 05:50:29.119: 208.28.1.0/24 via 0.0.0.0 in 2 hops *Mar 1 05:50:29.119: 208.28.1.64/28 via 0.0.0.0 in 1 hops *Mar 1 05:50:29.119: 208.28.1.128/27 via 0.0.0.0 in 2 hops *Mar 1 05:50:29.119: 208.28.1.193/32 via 0.0.0.0 in 7 hops *Mar 1 05:50:29.119: 208.28.1.194/32 via 0.0.0.0 in 4 hops R3(config-router)#^Z R3# *Mar 1 05:50:54.709: %SYS-5-CONFIG_I: Configured from console by console R3#config 5t ^ % Invalid input detected at '^' marker. R3#config 5t    t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router ro~  ip R3(config-router)#router ripdo u all deb ip rippassive-interface s 1/0Npassive-interface s 1/0Opassive-interface s 1/0 passive-interface s 1/0 R3(config-router)#^Z R3# RACK10AS#2 [Resuming connection 2 to r2 ... ] *Ma R2#CONFIG T Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router r eigrp 10- 0 R2(config-router)#pass s 1/0.2 R2(config-router)# *Mar 1 05:53:58.422: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is down: interface passive R2(config-router)#pass s 1/0.2bpass s 1/0.2pass s 1/0.2 npass s 1/0.2opass s 1/0.2 pass s 1/0.2 R2(config-router)#\ ^Z R2# *Mar 1 05:54:14.541: %SYS-5-CONFIG_I: Configured from console by console R2# *Mar 1 05:54:16.288: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.66 (Serial1/0.2) is up: new adjacency R2# RACK10AS#1 [Resuming connection 1 to r1 ... ] *Mar R1#confi gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router ospf 1 R1(config-router)#newt    t 17.57.100.1 0.0.0.0 area 0 R1(config-router)#^Z R1# RACK10AS#6 [Resuming connection 6 to r6 ... ] S6#sh    c config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#router ospf 1 S6(config-router)#net 17.57.100.2 % Incomplete command. S6(config-router)#.net 17.57.100.2 0.0.0.0 area 0 S6(config-router)#^Z S6# RACK10AS#3 [Resuming connection 3 to r3 ... ] *Ma R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer      uter ospf 1 R3(config-router)#nbet 17.80.1.1 0.0.0.0 area 0bet 17.80.1.1 0.0.0.0 area 0  R3(config-router)#^Z R3# RACK10AS#4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router ospf 1 R4(config-router)#net 17.80.1.2 0.0.0.0 area 0 R4(config-router)#^Z R4# *Mar 1 06:01:09.006: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 208.28.1.2 1 2WAY/DROTHER 00:00:35 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 208.28.1.2 1 EXSTART/DR 00:00:37 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 208.28.1.2 1 EXSTART/DR 00:00:35 17.80.1.1 FastEthernet0/0 R4# *Mar 1 06:01:50.442: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 208.28.1.2 1 FULL/DR 00:00:39 17.80.1.1 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 208.28.1.2 1 FULL/DR 00:00:38 17.80.1.1 FastEthernet0/0 R4# RACK10AS#1 [Resuming connection 1 to r1 ... ] *Mar R1#shrun      run | b routeer         ospf router ospf 1 log-adjacency-changes network 17.57.100.1 0.0.0.0 area 0 ! router rip version 2 redistribute eigrp 100 metric 2 route-map Prob5b passive-interface Ethernet0/0 network 208.28.1.0 maximum-paths 3 default-metric 2 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.194 ! route-map Prob5b permit 10 match ip address 1 set metric 7 --More--   R1# RACK10AS#2 3 [Resuming connection 3 to r3 ... ] * R3#sh run | b ospf router ospf 1 log-adjacency-changes network 17.80.1.1 0.0.0.0 area 0 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! --More--   R3# RACK10AS#4 [Resuming connection 4 to r4 ... ] R4#sh run | b ospf router ospf 1 log-adjacency-changes network 17.80.1.2 0.0.0.0 area 0 ! no ip http server no ip http secure-server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! end --More--   R4# RACK10AS#6 [Resuming connection 6 to r6 ... ] 06 S6#sh ru |     un | n   b ospf router ospf 1 log-adjacency-changes network 17.57.100.2 0.0.0.0 area 0 ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 line vty 0 4 login line vty 5 15 login ! ! end S6# S6# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1#sh ip int be rie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Serial0/0.2 180.40.7.66 YES manual up up Ethernet0/1 17.57.100.1 YES manual up up Serial0/1 unassigned YES unset administratively down down R1#  confi gt ^ % Invalid input detected at '^' marker. R1#conf ig t ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int lo 0 R1(config-if)#ip add 222 32 .1.1.1 255.255.255.0 R1(config-if)# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int .o  lo 0 R3(config-if)#i0p 222.p 222. p 222.1.1.3 255.255.255.0 ^ % Invalid input detected at '^' marker. R3(config-if)#ip 222.1.1.3 255.255.255.0a222.1.1.3 255.255.255.0d222.1.1.3 255.255.255.0d222.1.1.3 255.255.255.0 222.1.1.3 255.255.255.0 R3(config-if)#.t u tu       int tu 0 R3(config-if)#tun *Mar 1 06:02:37.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R3(config-if)#tun sou lo 0 R3(config-if)#tun des 222.1.1.      3.1.1.1 R3(config-if)#ip addres 17.13.13.32  255.255.255.0 R3(config-if)#router ospf 1 R3(config-router)#net 17.13.13.3 0.0.0.0 area 0 R3(config-router)#^Z R3# *Mar 1 06:03:25.620: %SYS-5-CONFIG_I: Configured from console by console R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#net 17.13.13.3 0.0.0.0 area 0router ospf 1 ip addres 17.13.13.3 255.255.255.0tun des 223.1.1.1 sou lo 0 int tu 0  R3(config-if)#ke R3(config-if)#keepalive R3(config-if)#^Z R3# RACK10AS# [Resuming connection 3 to r3 ... ] *M R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer      uter rip R3(config-router)#net 222.1.1.0 R3(config-router)#^Z R3# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1(config-if)#int tu 0 R1(config-if)#ip ad *Mar 1 06:05:18.678: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#ip add 17.13.13.1 255.255.255.0 R1(config-if)#tun sou lo 0 R1(config-if)#tun des 223.1.1.      2.1.1.3 R1(config-if)#keep R1(config-if)# *Mar 1 06:05:43.330: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-if)#keep tun mode ? aurp AURP TunnelTalk AppleTalk encapsulation cayman Cayman TunnelTalk AppleTalk encapsulation dvmrp DVMRP multicast tunnel eon EON compatible CLNS tunnel gre generic route encapsulation protocol ipip IP over IP encapsulation iptalk Apple IPTalk encapsulation ipv6ip IPv6 over IP encapsulation mpls MPLS encapsulations nos IP over IP encapsulation (KA9Q/NOS compatible) R1(config-if)#tun mode *Mar 1 06:06:18.684: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#tun mode          mpo  ode ip R1(config-if)#mode ipv R1(config-if)#mode ipv6 R1(config-if)#mode ipv6         tun R1(config-if)#tunnel mo R1(config-if)#tunnel mode ip R1(config-if)#tunnel mode ipvc  R1(config-if)#tunnel mode ipv6ip ? 6to4 IPv6 automatic tunnelling using 6to4 auto-tunnel IPv6 automatic tunnelling using IPv4 compatible addresses isatap IPv6 automatic tunnelling using ISATAP R1(config-if)#tunnel mode ipv6ip                    do sh run | b tun R1(config-if)#do sh run | b tun un Tun  R1(config-if)#do sh run | b Tun     int interface Loopback0 ip address 223.1.1.1 255.255.255.0 ! interface Tunnel0 ip address 17.13.13.1 255.255.255.0 keepalive 10 3 tunnel source Loopback0 tunnel destination 222.1.1.3 ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 --More--   R1(config-if)#router rip R1(config-router)#net 223.1.1.1 R1(config-router)#roputer     uter ospf 1 R1(config-router)#net 17.13.13.1 0.0.0.0 zra     area 0 R1(config-router)#^Z R1#s *Mar 1 06:13:26.089: %SYS-5-CONFIG_I: Configured from console by console R1#ship     ip osp *Mar 1 06:13:28.982: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 17.57.100.2 1 FULL/BDR 00:00:34 17.57.100.2 Ethernet0/1 R1# *Mar 1 06:13:33.393: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from LOADING to FULL, Loading Done R1#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 208.28.1.2 0 FULL/ - 00:00:38 17.13.13.3 Tunnel0 17.57.100.2 1 FULL/BDR 00:00:36 17.57.100.2 Ethernet0/1 R1#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 208.28.1.2 0 FULL/ - 00:00:39 17.13.13.3 Tunnel0 17.57.100.2 1 FULL/BDR 00:00:37 17.57.100.2 Ethernet0/1 R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.13.13.0 is directly connected, Tunnel0 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:16, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D 208.28.1.193/32 [90/409600] via 208.28.1.65, 00:43:48, Ethernet0/0 D 208.28.1.194/32 [90/409600] via 208.28.1.65, 00:43:46, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 01:19:43, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:18:34, Null0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks --More--  R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:18, Serial0/0.1 D 180.40.0.0/16 is a summary, 01:20:30, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 O 17.80.1.0 [110/11112] via 17.13.13.3, 00:00:05, Tunnel0 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:24, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D 208.28.1.193/32 [90/409600] via 208.28.1.65, 00:43:56, Ethernet0/0 D 208.28.1.194/32 [90/409600] via 208.28.1.65, 00:43:55, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 01:19:51, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:18:42, Null0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:26, Serial0/0.1 D 180.40.0.0/16 is a summary, 01:20:37, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#sh run | b int interface Loopback0 ip address 223.1.1.1 255.255.255.0 ! interface Tunnel0 ip address 17.13.13.1 255.255.255.0 keepalive 10 3 tunnel source Loopback0 tunnel destination 222.1.1.3 ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 --More--   frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 half-duplex ! interface Serial0/1 no ip address shutdown ! router eigrp 100 redistribute rip metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router ospf 1 log-adjacency-changes network 17.13.13.1 0.0.0.0 area 0 network 17.57.100.1 0.0.0.0 area 0 ! router rip --More--   version 2 redistribute eigrp 100 metric 2 route-map Prob5b passive-interface Ethernet0/0 network 208.28.1.0 network 223.1.1.0 maximum-paths 3 default-metric 2 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.194 ! route-map Prob5b permit 10 match ip address 1 set metric 7 ! route-map Prob5b permit 20 match ip address 2 set metric 4 --More--   R1# RACK10AS#3 [Resuming connection 3 to r3 ... ] *Mar 1 06:04:17.365: %SYS-5-CONFIG_I: Configured from console R3#sh run | b int interface Loopback0 ip address 222.1.1.3 255.255.255.0 ! interface Tunnel0 ip address 17.13.13.3 255.255.255.0 keepalive 10 3 tunnel source Loopback0 tunnel destination 223.1.1.1 ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto --More--  ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown ! --More--  interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 17.13.13.3 0.0.0.0 area 0 network 17.80.1.1 0.0.0.0 area 0 ! router rip version 2 --More--   no validate-update-source timers basic 30 180 0 240 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! --More--   R3#ci  config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router rip R3(config-router)#red ospfd    1 met 2 R3(config-router)#router ospf 1 R3(config-router)#redi rip sub R3(config-router)#^Z R3# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1#confi g ^ % Invalid input detected at '^' marker. R1#tcon    co *Mar 1 06:15:38.045: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 06:15:39.043: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 06:15:39.043: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router rip R1(config-router)#red ospf 1 met 2 R1(config-router)#red ospf 1 met 2outer rip    ei R1(config-router)#router ei % Incomplete command. R1(config)#router eigrp 100 R1(config-router)#red ospf 1 met 128 2000 255 1 1550   500 R1(config-router)#router ospf 1 R1(config-router)#red rip sub R1(config-router)#red eigrp 100 sub R1(config-router)#^Z R1# *Mar 1 06:16:43.344: %SYS-5-CONFIG_I: Configured from console by console R1# *Mar 1 06:16:49.070: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1# *Mar 1 06:16:53.609: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from LOADING to FULL, Loading Done R1# *Mar 1 06:17:36.339: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired R1# *Mar 1 06:18:19.658: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from LOADING to FULL, Loading Done R1# RACK10AS#3 [Resuming connection 3 to r3 ... ] * R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:01, Tunnel0 C 222.1.1.0/24 is directly connected, Loopback0 O E2 223.1.1.0/24 [110/20] via 17.13.13.1, 00:00:01, Tunnel0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.193/32 [110/20] via 17.13.13.1, 00:00:01, Tunnel0 O E2 208.28.1.194/32 [110/20] via 17.13.13.1, 00:00:02, Tunnel0 O E2 208.28.1.128/27 [110/20] via 17.13.13.1, 00:00:02, Tunnel0 O E2 208.28.1.64/28 [110/20] via 17.13.13.1, 00:00:02, Tunnel0 C 208.28.1.0/29 is directly connected, Serial1/0 O E2 208.28.1.0/24 [110/20] via 17.13.13.1, 00:00:03, Tunnel0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 O E2 180.40.0.0/16 [110/20] via 17.13.13.1, 00:00:04, Tunnel0 O E2 180.40.7.64/27 [110/20] via 17.13.13.1, 00:00:04, Tunnel0 R3# *Mar 1 06:17:36.984: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 06:17:37.985: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 06:17:37.985: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.66 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pr R3(config)#ip prefix-list Prob  12 % Incomplete command. R3(config)#ip prefix-list Prob12 223.1.1.0/24 ^ % Invalid input detected at '^' marker. R3(config)#ip prefix-list Prob12 223.1.1.0/24   223.1.1.0/24 d223.1.1.0/24 e223.1.1.0/24 n223.1.1.0/24 y223.1.1.0/24  223.1.1.0/24  R3(config)#ip prefix-list Prob12 deny 223.1.1.0/24                   ::   *Mar 1 06:18:47.988: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3(config)#ip prefix-list Prob12 0.0.0.0  /0 le 32 ^ % Invalid input detected at '^' marker. R3(config)# *Mar 1 06:18:54.527: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.66 on Tunnel0 from LOADING to FULL, Loading Done R3(config)#ip prefix-list Prob12 0.0.0.0/0 le 32p0.0.0.0/0 le 32e0.0.0.0/0 le 32r0.0.0.0/0 le 32 ^ % Invalid input detected at '^' marker. R3(config)#ip prefix-list Prob12 per0.0.0.0/0 le 32 0.0.0.0/0 le 32 R3(config)# *Mar 1 06:19:06.987: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 06:19:07.989: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 06:19:07.989: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.66 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config)#router ospf 1 R3(config-router)#die str R3(config-router)#distribute-list ? <1-199> IP access list number <1300-2699> IP expanded access list number WORD Access-list name gateway Filtering incoming updates based on gateway prefix Filter prefixes in routing updates route-map Filter prefixes based on the route-map R3(config-router)#distribute-list pr R3(config-router)#distribute-list prefix Prob12 in tun 0 R3(config-router)#^Z R3# *Mar 1 06:20:10.043: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 06:20:17.992: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R3#config tsh ip routeconfig t sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 C 17.80.1.0 is directly connected, FastEthernet0/0 R 17.57.100.0 [120/2] via 208.28.1.1, 00:00:00, Serial1/0 C 222.1.1.0/24 is directly connected, Loopback0 R 223.1.1.0/24 [120/1] via 208.28.1.1, 00:00:00, Serial1/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.3, 00:00:13, Serial1/0 [120/7] via 208.28.1.1, 00:00:00, Serial1/0 R 208.28.1.194/32 [120/4] via 208.28.1.3, 00:00:15, Serial1/0 [120/4] via 208.28.1.1, 00:00:01, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:15, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:01, Serial1/0 --More--  C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:01, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:01, Serial1/0 R 180.40.7.64/27 [120/1] via 208.28.1.3, 00:00:15, Serial1/0 R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 C 17.80.1.0 is directly connected, FastEthernet0/0 R 17.57.100.0 [120/2] via 208.28.1.1, 00:00:03, Serial1/0 C 222.1.1.0/24 is directly connected, Loopback0 R 223.1.1.0/24 [120/1] via 208.28.1.1, 00:00:03, Serial1/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.3, 00:00:16, Serial1/0 [120/7] via 208.28.1.1, 00:00:03, Serial1/0 R 208.28.1.194/32 [120/4] via 208.28.1.3, 00:00:17, Serial1/0 [120/4] via 208.28.1.1, 00:00:04, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:17, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:04, Serial1/0 --More--  C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:04, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:04, Serial1/0 R 180.40.7.64/27 [120/1] via 208.28.1.3, 00:00:17, Serial1/0 R3# *Mar 1 06:20:28.625: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.66 on Tunnel0 from LOADING to FULL, Loading Done R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 C 17.80.1.0 is directly connected, FastEthernet0/0 R 17.57.100.0 [120/2] via 208.28.1.1, 00:00:06, Serial1/0 C 222.1.1.0/24 is directly connected, Loopback0 R 223.1.1.0/24 [120/1] via 208.28.1.1, 00:00:06, Serial1/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks R 208.28.1.193/32 [120/7] via 208.28.1.3, 00:00:19, Serial1/0 [120/7] via 208.28.1.1, 00:00:06, Serial1/0 R 208.28.1.194/32 [120/4] via 208.28.1.3, 00:00:21, Serial1/0 [120/4] via 208.28.1.1, 00:00:07, Serial1/0 R 208.28.1.128/27 [120/1] via 208.28.1.3, 00:00:21, Serial1/0 R 208.28.1.64/28 [120/1] via 208.28.1.1, 00:00:07, Serial1/0 --More--  C 208.28.1.0/29 is directly connected, Serial1/0 R 208.28.1.0/24 [120/2] via 208.28.1.1, 00:00:07, Serial1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 R 180.40.0.0/16 [120/2] via 208.28.1.1, 00:00:07, Serial1/0 R 180.40.7.64/27 [120/1] via 208.28.1.3, 00:00:21, Serial1/0 R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:00, Tunnel0 C 222.1.1.0/24 is directly connected, Loopback0 R 223.1.1.0/24 [120/1] via 208.28.1.1, 00:00:08, Serial1/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.193/32 [110/20] via 17.13.13.1, 00:00:00, Tunnel0 O E2 208.28.1.194/32 [110/20] via 17.13.13.1, 00:00:01, Tunnel0 O E2 208.28.1.128/27 [110/20] via 17.13.13.1, 00:00:01, Tunnel0 O E2 208.28.1.64/28 [110/20] via 17.13.13.1, 00:00:01, Tunnel0 C 208.28.1.0/29 is directly connected, Serial1/0 O E2 208.28.1.0/24 [110/20] via 17.13.13.1, 00:00:01, Tunnel0 --More--   R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 C 17.80.1.0 is directly connected, FastEthernet0/0 O 17.57.100.0 [110/11121] via 17.13.13.1, 00:00:07, Tunnel0 C 222.1.1.0/24 is directly connected, Loopback0 R 223.1.1.0/24 [120/1] via 208.28.1.1, 00:00:15, Serial1/0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks O E2 208.28.1.193/32 [110/20] via 17.13.13.1, 00:00:07, Tunnel0 O E2 208.28.1.194/32 [110/20] via 17.13.13.1, 00:00:08, Tunnel0 O E2 208.28.1.128/27 [110/20] via 17.13.13.1, 00:00:08, Tunnel0 O E2 208.28.1.64/28 [110/20] via 17.13.13.1, 00:00:08, Tunnel0 C 208.28.1.0/29 is directly connected, Serial1/0 O E2 208.28.1.0/24 [110/20] via 17.13.13.1, 00:00:08, Tunnel0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.0/27 is directly connected, Serial1/2 O E2 180.40.0.0/16 [110/20] via 17.13.13.1, 00:00:10, Tunnel0 O E2 180.40.7.64/27 [110/20] via 17.13.13.1, 00:00:10, Tunnel0 R3# *Mar 1 06:21:16.119: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.66 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired R3# *Mar 1 06:21:58.460: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.66 on Tunnel0 from LOADING to FULL, Loading Done R3# *Mar 1 06:22:46.094: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.66 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired R3# RACK10AS#1 [Resuming connection 1 to r1 ... ] *Ma R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do sh access-list Standard IP access list 1 10 permit 208.28.1.193 (1 match) Standard IP access list 2 10 permit 208.28.1.194 (1 match) R1(config)#access-list 3 per *Mar 1 06:24:19.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config)#access-list 3 per 222.1.1.0 *Mar 1 06:24:23.707: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from LOADING to FULL, Loading Done R1(config)#access-list 3 per 222.1.1.0 R1(config)#router ospf 1 *Mar 1 06:24:38.231: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 06:24:39.232: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 06:24:39.232: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R1(config)#router ospf 1 R1(config-router)#dist R1(config-router)#dist ta R1(config-router)#distance ? <1-255> Administrative distance ospf OSPF distance R1(config-router)#distance *Mar 1 06:25:49.235: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-router)#distance *Mar 1 06:25:53.682: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from LOADING to FULL, Loading Done R1(config-router)#distance 175 ? A.B.C.D IP Source address R1(config-router)#distance 175 *Mar 1 06:26:08.250: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 06:26:09.240: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 06:26:09.252: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-router)#distance 175 ? A.B.C.D IP Source address R1(config-router)#distance 175   RACK10AS#3 [Resuming connection 3 to r3 ... ] *Mar R3#sh ip ospf Routing Process "ospf 1" with ID 208.28.1.2 Supports only single TOS(TOS0) routes Supports opaque LSA Supports Link-local Signaling (LLS) It is an autonomous system boundary router Redistributing External Routes from, rip, includes subnets in redistribution Initial SPF schedule delay 5000 msecs Minimum hold time between two consecutive SPFs 10000 msecs Maximum wait time between two consecutive SPFs 10000 msecs Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs LSA group pacing timer 240 secs Interface flood pacing timer 33 msecs Retransmission pacing timer 66 msecs Number of external LSA 16. Checksum Sum 0x06CB28 Number of opaque AS LSA 0. Checksum Sum 0x000000 Number of DCbitless external and opaque AS LSA 0 Number of DoNotAge external and opaque AS LSA 0 Number of areas in this router is 1. 1 normal 0 stub 0 nssa External flood list length 0 Area BACKBONE(0) Number of interfaces in this area is 2 Area has no authentication --More-- *Mar 1 06:25:46.154: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.66 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired --More-- RACK10AS#1 [Resuming connection 1 to r1 ... ] R1(config-router)#distance 175 R1(config-router)#~distance 175 208.28.1.2 208.28.1.2  208.28.1.2  208.28.1.2 2 208.28.1.25 208.28.1.25 208.28.1.2 208.28.1.2 *Mar 1 06:27:19.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-router)#distance 255 208.28.1.2 0.0.0.0 *Mar 1 06:27:23.686: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on Tunnel0 from LOADING to FULL, Loading Done R1(config-router)#distance 255 208.28.1.2 0.0.0.0                                 router R1(config-router)#router-id 1.1.1.1 Reload or use "clear ip ospf process" command, for this to take effect R1(config-router)#do clea ip ospf pro Reset ALL OSPF processes? [no]: R1(config-router)#do clea ip ospf pro Reset ALL OSPF processes? [no]: y R1(config-router)# RACK10AS#3 [Resuming connection 3 to r3 ... ] *Mar  SPF algorithm last executed 00:02:00.906 ago --More-- *Mar 1 06:27:02.996: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.66 on Tunnel0 from FULL to DOWN, Neighbor Down: Adjacency forced to reset --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#\rou    rou *Mar 1 06:27:08.529: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3(config)#router ospf 1 R3(config-router)#rout R3(config-router)#router-id 3.3.3.3 Reload or use "clear ip ospf process" command, for this to take effect R3(config-router)#^Z R3# *Mar 1 06:27:16.730: %SYS-5-CONFIG_I: Configured from console by console R3#clea ip route       ospf pro Reset ALL OSPF processes? [no]: y R3#^Z R3# *Mar 1 06:27:24.659: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 06:27:24.659: %OSPF-5-ADJCHG: Process 1, Nbr 17.80. RACK10AS#1 [Resuming connection 1 to r1 ... ] *Mar R1(config-router)# *Mar 1 06:28:28.672: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Tunnel0 from LOADING to FULL, Loading Done R1(config-router)#dist R1(config-router)#dista R1(config-router)#distance 255 3.3.3.3 0.0.0.0 3 ? R1(config-router)#distance 255 3.3.3.3 0.0.0.0 3   R1(config-router)#^Z R1#sh acce *Mar 1 06:28:55.056: %SYS-5-CONFIG_I: Configured from console by console R1#sh access-list Standard IP access list 1 10 permit 208.28.1.193 (1 match) Standard IP access list 2 10 permit 208.28.1.194 (1 match) Standard IP access list 3 10 permit 222.1.1.0 (1 match) R1#sh ip osp fnei ^ % Invalid input detected at '^' marker. R1#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 0 FULL/ - 00:00:38 17.13.13.3 Tunnel0 17.57.100.2 1 FULL/DR 00:00:34 17.57.100.2 Ethernet0/1 R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 R 17.80.1.0 [120/2] via 208.28.1.2, 00:00:03, Serial0/0.1 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:03, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D 208.28.1.193/32 [90/409600] via 208.28.1.65, 00:59:25, Ethernet0/0 D 208.28.1.194/32 [90/409600] via 208.28.1.65, 00:59:23, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 01:35:19, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:34:10, Null0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:04, Serial0/0.1 D 180.40.0.0/16 is a summary, 01:36:05, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 R 17.80.1.0 [120/2] via 208.28.1.2, 00:00:06, Serial0/0.1 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:06, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D 208.28.1.193/32 [90/409600] via 208.28.1.65, 00:59:28, Ethernet0/0 D 208.28.1.194/32 [90/409600] via 208.28.1.65, 00:59:26, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 01:35:22, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:34:13, Null0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:08, Serial0/0.1 D 180.40.0.0/16 is a summary, 01:36:08, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 R 17.80.1.0 [120/2] via 208.28.1.2, 00:00:20, Serial0/0.1 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:20, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D 208.28.1.193/32 [90/409600] via 208.28.1.65, 00:59:41, Ethernet0/0 D 208.28.1.194/32 [90/409600] via 208.28.1.65, 00:59:40, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 01:35:36, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:34:27, Null0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks R 180.40.7.0/27 [120/1] via 208.28.1.2, 00:00:22, Serial0/0.1 D 180.40.0.0/16 is a summary, 01:36:22, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1#sh i ip proto Routing Protocol is "eigrp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates Default networks accepted from incoming updates EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0 EIGRP maximum hopcount 100 EIGRP maximum metric variance 1 Redistributing: eigrp 100, rip, ospf 1 (internal, external 1 & 2, nssa-external 1 & 2) EIGRP NSF-aware route hold timer is 240s Automatic network summarization is in effect Automatic address summarization: 208.28.1.0/24 for Serial0/0.2 Summarizing with metric 281600 180.40.0.0/16 for Ethernet0/0 Summarizing with metric 2169856 Maximum path: 4 Routing for Networks: 180.40.7.66/32 208.28.1.66/32 Routing Information Sources: --More--   Gateway Distance Last Update (this router) 90 00:34:37 208.28.1.65 90 00:01:04 180.40.7.65 90 00:01:04 Distance: internal 90 external 170 Routing Protocol is "rip" Sending updates every 30 seconds, next due in 22 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default redistribution metric is 2 Redistributing: eigrp 100, rip, ospf 1 (internal, external 1 & 2, nssa-external 1 & 2) Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain Serial0/0.1 2 2 Loopback0 2 2 Automatic network summarization is not in effect Maximum path: 3 Routing for Networks: 208.28.1.0 --More--   Interface Send Recv Triggered RIP Key-chain 223.1.1.0 Passive Interface(s): Ethernet0/0 Routing Information Sources: Gateway Distance Last Update 208.28.1.2 120 00:00:19 Distance: (default is 120) Routing Protocol is "ospf 1" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Router ID 1.1.1.1 It is an autonomous system boundary router Redistributing External Routes from, eigrp 100, includes subnets in redistribution rip, includes subnets in redistribution Number of areas in this router is 1. 1 normal 0 stub 0 nssa Maximum path: 4 Routing for Networks: 17.13.13.1 0.0.0.0 area 0 17.57.100.1 0.0.0.0 area 0 Routing Information Sources: --More--   Gateway Distance Last Update 3.3.3.3 255 00:00:57 17.80.1.2 175 00:00:57 Distance: (default is 175) Address Wild mask Distance List 3.3.3.3 0.0.0.0 255 3 R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router ospf 1 R1(config-router)#no dista 175 R1(config-router)#^Z R1# *Mar 1 06:30:21.958: %SYS-5-CONFIG_I: Configured from console by console R1#config tsh ip protoroute Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 3 subnets C 17.13.13.0 is directly connected, Tunnel0 O 17.80.1.0 [110/11112] via 17.13.13.3, 00:00:04, Tunnel0 C 17.57.100.0 is directly connected, Ethernet0/1 R 222.1.1.0/24 [120/1] via 208.28.1.2, 00:00:15, Serial0/0.1 C 223.1.1.0/24 is directly connected, Loopback0 208.28.1.0/24 is variably subnetted, 6 subnets, 5 masks D 208.28.1.193/32 [90/409600] via 208.28.1.65, 01:00:33, Ethernet0/0 D 208.28.1.194/32 [90/409600] via 208.28.1.65, 01:00:31, Ethernet0/0 D 208.28.1.128/27 [90/281856] via 208.28.1.65, 01:36:27, Ethernet0/0 C 208.28.1.64/28 is directly connected, Ethernet0/0 C 208.28.1.0/29 is directly connected, Serial0/0.1 D 208.28.1.0/24 is a summary, 00:35:18, Null0 --More--   180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks O E2 180.40.7.0/27 [110/20] via 17.13.13.3, 00:00:06, Tunnel0 D 180.40.0.0/16 is a summary, 01:37:13, Null0 C 180.40.7.64/27 is directly connected, Serial0/0.2 R1# RACK10AS#3 [Resuming connection 3 to r3 ... ] net0/0 from FULL to DOWN, R3#sh ip pr % Ambiguous command: "sh ip pr" R3#sh ip pre ip prefix-list Prob12: 2 entries seq 5 deny 223.1.1.0/24 seq 10 permit 0.0.0.0/0 le 32 R3# RACK10AS#4 [Resuming connection 4 to r4 ... ] *Mar R4#ping 208.28.1.193 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.193, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 64/67/72 ms R4#ping 208.28.1.193 4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.194, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 52/64/72 ms R4# RACK10AS#1 [Resuming connection 1 to r1 ... ] R1#sh run | b router ospf       router eigrp 100 redistribute rip metric 128 2000 255 1 1500 redistribute ospf 1 metric 128 2000 255 1 1500 network 180.40.7.66 0.0.0.0 network 208.28.1.66 0.0.0.0 neighbor 180.40.7.65 Serial0/0.2 auto-summary ! router ospf 1 router-id 1.1.1.1 log-adjacency-changes redistribute eigrp 100 subnets redistribute rip subnets network 17.13.13.1 0.0.0.0 area 0 network 17.57.100.1 0.0.0.0 area 0 distance 255 3.3.3.3 0.0.0.0 3 ! router rip version 2 redistribute eigrp 100 metric 2 route-map Prob5b redistribute ospf 1 metric 2 passive-interface Ethernet0/0 network 208.28.1.0 --More--   network 223.1.1.0 maximum-paths 3 default-metric 2 no auto-summary ! no ip http server ip classless ! ! access-list 1 permit 208.28.1.193 access-list 2 permit 208.28.1.194 access-list 3 permit 222.1.1.0 ! route-map Prob5b permit 10 match ip address 1 set metric 7 ! route-map Prob5b permit 20 match ip address 2 set metric 4 ! route-map Prob5b permit 30 ! --More--   R1# RACK10AS#3 [Resuming connection 3 to r3 ... ] R3#sh run | b router router ospf 1 router-id 3.3.3.3 log-adjacency-changes redistribute rip subnets network 17.13.13.3 0.0.0.0 area 0 network 17.80.1.1 0.0.0.0 area 0 distribute-list prefix Prob12 in Tunnel0 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 redistribute ospf 1 metric 2 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! --More--  no ip http server no ip http secure-server ! ! ip prefix-list Prob12 seq 5 deny 223.1.1.0/24 ip prefix-list Prob12 seq 10 permit 0.0.0.0/0 le 32 ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! end --More--   R3#sh clock *06:32:07.447 UTC Mon Mar 1 1993 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#tim R3(config)#time-range ? WORD Time range name R3(config)#time-range Prob14 R3(config-time-range)#? Time range configuration commands: absolute absolute time and date default Set a command to its defaults exit Exit from time-range configuration mode no Negate a command or set its defaults periodic periodic time and date R3(config-time-range)#per ? Friday Friday Monday Monday Saturday Saturday Sunday Sunday Thursday Thursday Tuesday Tuesday Wednesday Wednesday daily Every day of the week weekdays Monday thru Friday weekend Saturday and Sunday R3(config-time-range)#per week R3(config-time-range)#per weekd R3(config-time-range)#per weekdays ? hh:mm Starting time R3(config-time-range)#per weekdays 07:00 ? to ending day and time R3(config-time-range)#per weekdays 07:00 to 6:30    18:30 ? R3(config-time-range)#per weekdays 07:00 to 18:30 R3(config-time-range)#exit R3(config)#access-list 100 per ospf any any tim R3(config)#access-list 100 per ospf any any time-range Prob14 R3(config)#access-list 100 per ospf any any time-range Prob14 access-list 100 den ospf anyt    any R3(config)#access-l;ist    ist 100 per ip any any R3(config)#int tu 0 R3(config-if)#ip access 100 in R3(config-if)#^Z R3#sh *Mar 1 06:35:04.156: %SYS-5-CONFIG_I: Configured from console by console R3#sh access-list Extended IP access list 100 10 permit ospf any any time-range Prob14 (inactive) 20 deny ospf any any (2 matches) 30 permit ip any any (2 matches) R3#sh ip ospf n *Mar 1 06:35:23.208: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 17.80.1.2 1 FULL/DR 00:00:36 17.80.1.2 FastEthernet0/0 R3# R3# R3# R3#set clock ? % Unrecognized command R3#set clock           clock set ? hh:mm:ss Current Time R3#clock set 12:00:00 ? <1-31> Day of the month MONTH Month of the year R3#clock set 12:00:00 12 apri ? <1993-2035> Year R3#clock set 12:00:00 12 apri 2009 R3#clock set 12:00:00 12 apri 2009sh ip ospf nei access-list  Extended IP access list 100 10 permit ospf any any time-range Prob14 (inactive) 20 deny ospf any any (7 matches) 30 permit ip any any (7 matches) R3#sh access-list Extended IP access list 100 10 permit ospf any any time-range Prob14 (inactive) 20 deny ospf any any (7 matches) 30 permit ip any any (7 matches) R3#sh access-list Extended IP access list 100 10 permit ospf any any time-range Prob14 (inactive) 20 deny ospf any any (7 matches) 30 permit ip any any (7 matches) R3#sh access-list Extended IP access list 100 10 permit ospf any any time-range Prob14 (inactive) 20 deny ospf any any (7 matches) 30 permit ip any any (7 matches) R3#sh access-list Extended IP access list 100 10 permit ospf any any time-range Prob14 (inactive) 20 deny ospf any any (7 matches) 30 permit ip any any (7 matches) R3#sh access-list Extended IP access list 100 10 permit ospf any any time-range Prob14 (inactive) 20 deny ospf any any (8 matches) 30 permit ip any any (8 matches) R3#sh access-list Extended IP access list 100 10 permit ospf any any time-range Prob14 (inactive) 20 deny ospf any any (8 matches) 30 permit ip any any (8 matches) R3#sh ip      h tiu  ime R3#sh time-range time-range entry: Prob14 (inactive) periodic weekdays 7:00 to 18:30 used in: IP ACL entry R3#sh clock 12:00:25.794 UTC Sun Apr 12 2009 R3#confi g ^ % Invalid input detected at '^' marker. R3#t confi gsh clock 12:00:37.553 UTC Sun Apr 12 2009 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#co  clo ? summer-time Configure summer (daylight savings) time timezone Configure time zone R3(config)#clo sum R3(config)#clo summer-time ? WORD name of time zone in summer R3(config)#clo summer-time             tim ? WORD name of time zone R3(config)#clo tim PST ? <-23 - 23> Hours offset from UTC R3(config)#clo tim PST -8 R3(config)#^Z R3#config tsh clock 04:01:09.493 PST Sun Apr 12 2009 R3# Apr 12 12:01:08.095: %SYS-5-CONFIG_I: Configured from console by console R3#sh clockconfig tsh clockconfig tsh clockconfi g sh clocktime-range access-listtime-range time-range entry: Prob14 (inactive) periodic weekdays 7:00 to 18:30 used in: IP ACL entry R3#sh time-range clock config tsh clockconfi g sh clocktime-range access-listclock set 12:00:00 12 apri 20092 apri 2009 3 apri 2009 R3#^Z R3#clock set 12:00:00 13 apri 2009sh time-range  time-range entry: Prob14 (active) periodic weekdays 7:00 to 18:30 used in: IP ACL entry R3#sh time-range clock set 12:00:00 13 apri 2009sh time-range clock config tsh clockconfi g sh clocktime-range access-list Extended IP access list 100 10 permit ospf any any time-range Prob14 (active) 20 deny ospf any any (17 matches) 30 permit ip any any (17 matches) R3# Apr 13 20:00:09.876: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Tunnel0 from LOADING to FULL, Loading Done R3#sh run | b int interface Loopback0 ip address 222.1.1.3 255.255.255.0 ! interface Tunnel0 ip address 17.13.13.3 255.255.255.0 ip access-group 100 in keepalive 10 3 tunnel source Loopback0 tunnel destination 223.1.1.1 ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto --More--   speed auto ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon frame-relay map ip 208.28.1.1 301 frame-relay map ip 208.28.1.3 302 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip rip triggered ip rip authentication mode md5 ip rip authentication key-chain Prob4 ! interface Serial1/3 no ip address shutdown --More--  ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 3.3.3.3 log-adjacency-changes redistribute rip subnets network 17.13.13.3 0.0.0.0 area 0 network 17.80.1.1 0.0.0.0 area 0 --More--   distribute-list prefix Prob12 in Tunnel0 ! router rip version 2 no validate-update-source timers basic 30 180 0 240 redistribute ospf 1 metric 2 network 180.40.0.0 network 208.28.1.0 network 222.1.1.0 neighbor 208.28.1.3 neighbor 208.28.1.1 maximum-paths 3 no auto-summary ! ip classless ! no ip http server no ip http secure-server ! ! ip prefix-list Prob12 seq 5 deny 223.1.1.0/24 ip prefix-list Prob12 seq 10 permit 0.0.0.0/0 le 32 --More--  access-list 100 permit ospf any any time-range Prob14 access-list 100 deny ospf any any access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! time-range Prob14 periodic weekdays 7:00 to 18:30 ! ! end --More--   R3#