=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.12.04 18:53:47 =~=~=~=~=~=~=~=~=~=~=~= RACK18AS>45 % 45 is not an open connection RACK18AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip int bri            int status Port Name Status Vlan Duplex Speed Type Fa0/1 connected 1 a-half a-10 10/100BaseTX Fa0/2 disabled 1 auto auto 10/100BaseTX Fa0/3 connected 1 a-full a-100 10/100BaseTX Fa0/4 disabled 1 auto auto 10/100BaseTX Fa0/5 notconnect 1 auto auto 10/100BaseTX Fa0/6 notconnect 1 auto auto 10/100BaseTX Fa0/7 notconnect 1 auto auto 10/100BaseTX Fa0/8 connected 1 a-half a-10 10/100BaseTX Fa0/9 notconnect 1 auto auto 10/100BaseTX Fa0/10 notconnect 1 auto auto 10/100BaseTX Fa0/11 notconnect 1 auto auto 10/100BaseTX Fa0/12 notconnect 1 auto auto 10/100BaseTX Fa0/13 notconnect 1 auto auto 10/100BaseTX Fa0/14 notconnect 1 auto auto 10/100BaseTX Fa0/15 notconnect 1 auto auto 10/100BaseTX Fa0/16 notconnect 1 auto auto 10/100BaseTX Fa0/17 notconnect 1 auto auto 10/100BaseTX Fa0/18 notconnect 1 auto auto 10/100BaseTX Fa0/19 notconnect 1 auto auto 10/100BaseTX Fa0/20 notconnect 1 auto auto 10/100BaseTX Fa0/21 notconnect 1 auto auto 10/100BaseTX --More--   S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#vlan 10 S5(config-vlan)#do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--  Remote SPAN VLANs ------------------------------------------------------------------------------ Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S5(config-vlan)#q name ToR1 S5(config-vlan)#exity ^ % Invalid input detected at '^' marker. S5(config-vlan)#exity  S5(config)#exityname ToR1do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 ToR1 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 --More--   S5(config)#so    do sh run | i vlan 10 S5(config)#do sh run | i vlan 10lan 10 Vlan 10 S5(config)#do sh run | i Vlan 1010  S5(config)#do sh run | i Vlan10lan10 vlan10 S5(config)#exit S5#vlan 04:26:49: %SYS-5-CONFIG_I: Configured from console by console S5#vlan data % Warning: It is recommended to configure VLAN from config mode, as VLAN database mode is being deprecated. Please consult user documentation for configuring VTP/VLAN in config mode. S5(vlan)# S5(vlan)# S5(vlan)#sh cuy  urr VLAN ISL Id: 1 Name: default Media Type: Ethernet VLAN 802.10 Id: 100001 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 10 Name: ToR1 Media Type: Ethernet VLAN 802.10 Id: 100010 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 1002 Name: fddi-default Media Type: FDDI VLAN 802.10 Id: 101002 State: Operational --More--   S5(vlan)#q ^ % Invalid input detected at '^' marker. S5(vlan)#exit APPLY completed. Exiting.... S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#vlan 20 S5(config-vlan)#name ToR2 S5(config-vlan)#exi S5(config)#vlan 34 S5(config-vlan)#name Bluer Suede S5(config-vlan)#exiy ^ % Invalid input detected at '^' marker. S5(config-vlan)#exiy t S5(config)#int vlan 10 S5(config-if)#i 04:28:16: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up S5(config-if)#ip add 208.28.1.65 255.255.255.240 S5(config-if)#exciy   it S5(config)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual up up FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down --More--   S5(config)#do sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S5(config)#no vlan 20 S5(config)#int vlan 20 S5(config-if)# 04:29:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down S5(config-if)# S5(config-if)# S5(config-if)#ip add 209 8.28.1.130 255.255.255.224 S5(config-if)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual up up Vlan20 208.28.1.130 YES manual down down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down --More--   S5(config-if)#vlan 20 S5(config-vlan)#namr ToR2 ^ % Invalid input detected at '^' marker. S5(config-vlan)#namr ToR2 ToR2 e ToR2 S5(config-vlan)#exit S5(config)#exitname ToR2r ToR2vlan 20 do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual up up Vlan20 208.28.1.130 YES manual up down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down --More--   S5(config)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual up up Vlan20 208.28.1.130 YES manual up down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down --More--   S5(config)#do sh ip int brie do sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual up up Vlan20 208.28.1.130 YES manual up down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down --More--   S5(config)#do sh int r   tru 04:30:43: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up S5(config)#do sh int trun Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S5(config)#do sh int trunp int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset administratively down down Vlan10 208.28.1.65 YES manual up up Vlan20 208.28.1.130 YES manual up up FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset administratively down down FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset administratively down down FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset down down FastEthernet0/8 unassigned YES unset up up FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down --More--   S5(config)#int     int f range fa 0/1 - 24 3 S5(config-if-range)#swi S5(config-if-range)#switchport mode access S5(config-if-range)#spee S5(config-if-range)#speed 100 S5(config-if-range)#du S5(config-if-range)#duplex 04:32:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down 04:32:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down 04:32:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to down 04:32:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down S5(config-if-range)#duplex 04:32:13: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to down 04:32:13: %LINK-3-UPDOWN: Interface FastEthernet0/8, changed state to down S5(config-if-range)#duplex 04:32:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up 04:32:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up S5(config-if-range)#duplex fu S5(config-if-range)#span S5(config-if-range)#spanning-tree 04:32:17: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down 04:32:17: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down S5(config-if-range)#spanning-tree 04:32:18: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down S5(config-if-range)#spanning-tree port 04:32:19: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up S5(config-if-range)#spanning-tree port S5(config-if-range)#spanning-tree portf S5(config-if-range)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast will be configured in 23 interfaces due to the range command but will only have effect when the interfaces are in a non-trunking mode. S5(config-if-range)# 04:32:21: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up 04:32:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up S5(config-if-range)# 04:32:40: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/3 (not half duplex), with R3 FastEthernet0/0 (half duplex). S5(config-if-range)# S5(config-if-range)# S5(config-if-range)# S5(config-if-range)#int fa 0./  /1 S5(config-if)#sp S5(config-if)#sp  speed S5(config-if)#speed 10 S5(config-if)#speed 10        du 04:32:57: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 04:32:58: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up S5(config-if)#du S5(config-if)#duplex 04:32:58: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/1 (not half duplex), with R1 Ethernet0/0 (half duplex). 04:32:58: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/1 (not half duplex), with R1 Ethernet0/0 (half duplex). 04:32:58: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/1 (not half duplex), with R1 Ethernet0/0 (half duplex). S5(config-if)#duplex ha S5(config-if)#duplex half S5(config-if)#int fa 0/24 S5(config-if)#speed S5(config-if)#speed 100 S5(config-if)# 04:33:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down 04:33:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to down 04:33:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down S5(config-if)# 04:33:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up S5(config-if)# 04:33:40: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/3 (not half duplex), with R3 FastEthernet0/0 (half duplex). S5(config-if)#du fu S5(config-if)# 04:33:51: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down S5(config-if)# RACK18AS>6 [Resuming connection 6 to r6 ... ] 04:3 S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# 04:33:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up S6(config)# 04:33:56: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/24 (not full duplex), with S5 FastEthernet0/24 (full duplex). 04:33:56: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/24 (not full duplex), with S5 FastEthernet0/24 (full duplex). 04:33:56: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/24 (not full duplex), with S5 FastEthernet0/24 (full duplex). S6(config)#int fa 0/1 04:33:59: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/24 (not full duplex), with S5 FastEthernet0/24 (full duplex). S6(config)#int fa 0/1 S6(config-if)#speed 10 S6(config-if)#du fu S6(config-if)#ex 04:34:04: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down S6(config-if)#exity ^ % Invalid input detected at '^' marker. S6(config-if)# 04:34:05: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to down S6(config-if)#exitydu fuspeed 10 04:34:07: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up S6(config-if)#speed 10int fa 0/1  04:34:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up S6(config-if)#int fa 0/2 - 24speed 10 du fu speed 10du fu exity exitydu fuspeed 10int fa 0/1   2 - 24 rfa 0/2 - 24afa 0/2 - 24nfa 0/2 - 24gfa 0/2 - 24efa 0/2 - 24 fa 0/2 - 24 S6(config-if-range)#speed 100 S6(config-if-range)#du fu S6(config-if-range)# 04:34:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down 04:34:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to down 04:34:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down S6(config-if-range)#du fu 04:34:38: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down 04:34:38: %LINK-3-UPDOWN: Interface FastEthernet0/4, changed state to down S6(config-if-range)#du fuspeed 100int range fa 0/2 - 24 3 04:34:42: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up 04:34:42: %LINK-3-UPDOWN: Interface FastEthernet0/4, changed state to up S6(config-if-range)#int range fa 0/2 - 23 - 23 1 - 23 S6(config-if-range)# 04:34:43: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up S6(config-if-range)#span 04:34:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up 04:34:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up S6(config-if-range)#span S6(config-if-range)#spanning-tree portf S6(config-if-range)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast will be configured in 23 interfaces due to the range command but will only have effect when the interfaces are in a non-trunking mode. S6(config-if-range)#SW S6(config-if-range)#SWitchport acce    mode acc S6(config-if-range)# 04:35:00: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/4 (not half duplex), with R4 FastEthernet0/0 (half duplex). S6(config-if-range)# RACK18AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa 0/1 R2(config-if)#sp R2(config-if)#speed 100 R2(config-if)#du fu R2(config-if)#^Z R2# RACK18AS>3 [Resuming connection 3 to r3 ... ] *M R3#int     conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int f a0/1 0 ^ % Invalid input detected at '^' marker. R3(config)#int f a0/0 a0/0  R3(config-if)#sp R3(config-if)#speed 100 R3(config-if)#du fu R3(config-if)#^Z R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#conf t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#sp R4(config-if)#speed 100 R4(config-if)#in  du fu R4(config-if)#^Z R4# RACK18AS>5 [Resuming connection 5 to r5 ... ] 04 S5(config-if)#int f a0? % Unrecognized command S5(config-if)#int f a03/3a0/3  S5(config-if)#swi S5(config-if)#switchport acc` S5(config-if)#switchport acc`  S5(config-if)#switchport access ` vlan 34 S5(config-if)#^Z S5#sh vtp   04:36:38: %SYS-5-CONFIG_I: Configured from console by console S5#sh vp   tp statu VTP Version : 2 Configuration Revision : 5 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0xAB 0xFE 0x40 0x75 0xCF 0xE5 0xAD 0x01 Configuration last modified by 208.28.1.65 at 3-1-93 04:30:12 Local updater ID is 208.28.1.65 on interface Vl10 (lowest numbered VLAN interface found) S5# RACK18AS>6 [Resuming connection 6 to r6 ... ] 04: S6(config-if-range)#o sh      do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 --More--   Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ S6(config-if-range)# RACK18AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#vtp domain Graceland Changing VTP domain name from NULL to Graceland S5(config)#int fa 0/1\ ^ % Invalid input detected at '^' marker. S5(config)#int fa 0/1\  S5(config-if)#sw S5(config-if)#switchport acc vlan 10 S5(config-if)#^Z S5# 04:38:17: %SYS-5-CONFIG_I: Configured from console by console S5# RACK18AS>5 6 [Resuming connection 6 to r6 ... ] S6(config-if-range)#do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 ToR1 active 20 ToR2 active 34 BlueSuede active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 --More--   S6(config-if-range)#dosh     sh vtp statu VTP Version : 2 Configuration Revision : 5 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0xE8 0xDF 0x13 0x19 0xD5 0x70 0x69 0xB1 Configuration last modified by 208.28.1.65 at 3-1-93 04:30:12 Local updater ID is 0.0.0.0 (no valid interface found) S6(config-if-range)# RACK18AS>5 [Resuming connection 5 to r5 ... ] S5#sh vtp stat VTP Version : 2 Configuration Revision : 5 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0xE8 0xDF 0x13 0x19 0xD5 0x70 0x69 0xB1 Configuration last modified by 208.28.1.65 at 3-1-93 04:30:12 Local updater ID is 208.28.1.65 on interface Vl10 (lowest numbered VLAN interface found) S5# RACK18AS>6 [Resuming connection 6 to r6 ... ] S6(config-if-range)#int fa 0/2 S6(config-if)# S6(config-if)#sw S6(config-if)#switchport ac S6(config-if)#switchport access v S6(config-if)#switchport access vlan 20 S6(config-if)#int fa 0/4 S6(config-if)#int fa 0/4switchport access vlan 20  34 S6(config-if)#int fa 0/1 S6(config-if)# S6(config-if)#no sw S6(config-if)#no switchport S6(config-if)#ip address 1 04:40:38: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 04:40:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up S6(config-if)#ip address 17.57.100/.2     .2 255.255.255.0 S6(config-if)#^Z S6# RACK18AS>1 [Resuming connection 1 to r1 ... ] * R1#sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Ethernet0/1 unassigned YES unset administratively down down Serial0/1 unassigned YES unset administratively down down R1#confi Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ip add 17.57.1001.  .1 255.255.255.0 R1(config-if)#no shut R1(config-if)#^Z R1# *Mar 1 04:39:23.940: %SYS-5-CONFIG_I: Configured from console by console R1# *Mar 1 04:39:25.667: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up *Mar 1 04:39:26.668: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed state to up R1# RACK18AS>6 [Resuming connection 6 to r6 ... ] 04:40:52: %SYS-5-CONFIG_I: Configured f S6#sh run Building configuration... Current configuration : 3177 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname S6 ! ! no aaa new-model ip subnet-zero no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst --More--  spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 no switchport ip address 17.57.100.2 255.255.255.0 speed 10 duplex full spanning-tree portfast ! interface FastEthernet0/2 switchport access vlan 20 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/3 switchport mode access shutdown speed 100 --More--   S6#o conf t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int f a  a 0/1 S6(config-if)#du ha; S6(config-if)#du ha;  S6(config-if)#du ha;  do sh run int fa 0/1 Building configuration... Current configuration : 133 bytes ! interface FastEthernet0/1 no switchport ip address 17.57.100.2 255.255.255.0 speed 10 duplex half spanning-tree portfast end S6(config-if)#^Z S6# 04:41:45: %SYS-5-CONFIG_I: Configured from console by console S6# S6# S6# S6#ping 17.57.100.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.57.100.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/206/1020 ms S6# RACK18AS>5 [Resuming connection 5 to r5 ... ] S5#ping 207 8/.2   .28.1.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/201/1000 ms S5#ping 208.28.1.129   66 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.66, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/202/1000 ms S5# RACK18AS>3 [Resuming connection 3 to r3 ... ] *M R3#ping 17.100.    80.1.1 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.2, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/3/4 ms R3#ping 17.80.1.2  RACK18AS>6 [Resuming connection 6 to r6 ... ] S6#sh vtp statu VTP Version : 2 Configuration Revision : 5 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0xE8 0xDF 0x13 0x19 0xD5 0x70 0x69 0xB1 Configuration last modified by 208.28.1.65 at 3-1-93 04:30:12 Local updater ID is 17.57.100.2 on interface Fa0/1 (first layer3 interface found) S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#vlan 99 S6(config-vlan)#exiy ^ % Invalid input detected at '^' marker. S6(config-vlan)#exiy  S6(config)# RACK18AS>5 [Resuming connection 5 to r5 ... ] S5#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/2, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Gi0/1, Gi0/2 10 ToR1 active Fa0/1 20 ToR2 active 34 BlueSuede active Fa0/3 99 VLAN0099 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 --More--   S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#no vlan 99 S5(config)#^Z S5# RACK18AS>6 [Resuming connection 6 to r6 ... ] S6(config)#sh    ^Z S6#sh 04:43:48: %SYS-5-CONFIG_I: Configured from console by console S6#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/3, Fa0/5, Fa0/6, Fa0/7 Fa0/8, Fa0/9, Fa0/10, Fa0/11 Fa0/12, Fa0/13, Fa0/14, Fa0/15 Fa0/16, Fa0/17, Fa0/18, Fa0/19 Fa0/20, Fa0/21, Fa0/22, Fa0/23 Gi0/1, Gi0/2 10 ToR1 active 20 ToR2 active Fa0/2 34 BlueSuede active Fa0/4 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 34 enet 100034 1500 - - - - - 0 0 --More--   S6#sh vtp statu VTP Version : 2 Configuration Revision : 7 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x1A 0x67 0x2A 0x74 0xA0 0x33 0x01 0x88 Configuration last modified by 208.28.1.65 at 3-1-93 04:43:44 Local updater ID is 17.57.100.2 on interface Fa0/1 (first layer3 interface found) S6# RACK18AS>5 [Resuming connection 5 to r5 ... ] 0 S5#sh run Building configuration... Current configuration : 3277 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname S5 ! ! no aaa new-model ip subnet-zero no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst --More--  spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport access vlan 10 switchport mode access speed 10 duplex half spanning-tree portfast ! interface FastEthernet0/2 switchport mode access shutdown speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/3 switchport access vlan 34 switchport mode access speed 100 --More--   duplex full spanning-tree portfast ! interface FastEthernet0/4 switchport mode access shutdown speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/5 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/6 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/7 --More--   switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/8 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/9 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/10 switchport mode access speed 100 duplex full spanning-tree portfast ! --More--  interface FastEthernet0/11 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/12 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/13 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/14 switchport mode access speed 100 duplex full spanning-tree portfast --More--  ! interface FastEthernet0/15 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/16 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/17 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/18 switchport mode access speed 100 duplex full --More--   spanning-tree portfast ! interface FastEthernet0/19 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/20 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/21 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/22 switchport mode access speed 100 --More--   duplex full spanning-tree portfast ! interface FastEthernet0/23 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/24 switchport mode dynamic desirable speed 100 duplex full ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address shutdown --More--  ! interface Vlan10 ip address 208.28.1.65 255.255.255.240 ! interface Vlan20 ip address 208.28.1.130 255.255.255.224 ! ip classless ip http server ip http secure-server ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 no login line vty 5 15 no login --More--  ! ! end S5# RACK18AS>6 [Resuming connection 6 to r6 ... ] S6#sh run Building configuration... Current configuration : 3177 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname S6 ! ! no aaa new-model ip subnet-zero no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst --More--  spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 no switchport ip address 17.57.100.2 255.255.255.0 speed 10 duplex half spanning-tree portfast ! interface FastEthernet0/2 switchport access vlan 20 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/3 switchport mode access shutdown speed 100 --More--   duplex full spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 34 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/5 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/6 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/7 --More--   switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/8 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/9 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/10 switchport mode access speed 100 duplex full spanning-tree portfast ! --More--  interface FastEthernet0/11 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/12 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/13 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/14 switchport mode access speed 100 duplex full spanning-tree portfast --More--  ! interface FastEthernet0/15 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/16 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/17 switchport mode access speed 100 duplex full spanning-tree portfast ! interface FastEthernet0/18 switchport mode access speed 100 duplex full --More--   S6# RACK18AS>5 [Resuming connection 5 to r5 ... ] S5# S5#vlan datat ^ % Invalid input detected at '^' marker. S5#vlan datat  % Warning: It is recommended to configure VLAN from config mode, as VLAN database mode is being deprecated. Please consult user documentation for configuring VTP/VLAN in config mode. S5(vlan)#sh  cur    curr VLAN ISL Id: 1 Name: default Media Type: Ethernet VLAN 802.10 Id: 100001 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 10 Name: ToR1 Media Type: Ethernet VLAN 802.10 Id: 100010 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 20 Name: ToR2 Media Type: Ethernet VLAN 802.10 Id: 100020 State: Operational --More--   MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 34 Name: BlueSuede Media Type: Ethernet VLAN 802.10 Id: 100034 State: Operational MTU: 1500 Backup CRF Mode: Disabled Remote SPAN VLAN: No VLAN ISL Id: 1002 Name: fddi-default Media Type: FDDI VLAN 802.10 Id: 101002 State: Operational MTU: 1500 Bridge Type: SRB Backup CRF Mode: Disabled Remote SPAN VLAN: No --More--   VLAN ISL Id: 1003 --More--   Name: token-ring-default --More--   Media Type: Token Ring --More--   S5(vlan)#s exit APPLY completed. Exiting.... S5#sh vtp statu VTP Version : 2 Configuration Revision : 7 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x1A 0x67 0x2A 0x74 0xA0 0x33 0x01 0x88 Configuration last modified by 208.28.1.65 at 3-1-93 04:43:44 Local updater ID is 208.28.1.65 on interface Vl10 (lowest numbered VLAN interface found) S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#vtp pr S5(config)#vtp pruning ? S5(config)#vtp pruning Pruning switched on S5(config)#^Z S5# 04:48:41: %SYS-5-CONFIG_I: Configured from console by console S5# RACK18AS>6 [Resuming connection 6 to r6 ... ] S6#sh vtp statu VTP Version : 2 Configuration Revision : 8 Maximum VLANs supported locally : 1005 Number of existing VLANs : 8 VTP Operating Mode : Server VTP Domain Name : Graceland VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x94 0x3E 0x21 0xDE 0x68 0x88 0xC0 0x8C Configuration last modified by 208.28.1.65 at 3-1-93 04:48:40 Local updater ID is 17.57.100.2 on interface Fa0/1 (first layer3 interface found) S6# S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6# S6# S6# S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,10,20,34 S6# S6# S6# S6# RACK18AS>5 [Resuming connection 5 to r5 ... ] S5#sh int turn   rn un Port Mode Encapsulation Status Native vlan Fa0/24 desirable n-isl trunking 1 Port Vlans allowed on trunk Fa0/24 1-4094 Port Vlans allowed and active in management domain Fa0/24 1,10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 1,20,34 S5# S5# S5# S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/24 S5(config-if)#swu i S5(config-if)#switchport mo S5(config-if)#switchport mode tra S5(config-if)#switchport mode tra u S5(config-if)#switchport mode trunk Command rejected: An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode. S5(config-if)#sw S5(config-if)#switchport tr S5(config-if)#switchport trunk en S5(config-if)#switchport trunk encapsulation do S5(config-if)#switchport trunk encapsulation dot1q S5(config-if)#switchport trunk encapsulation dot1q mode trunk  S5(config-if)# 04:54:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down 04:54:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down S5(config-if)# 04:54:16: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up S5(config-if)#sw S5(config-if)#switchport n S5(config-if)#switchport nonegotiate S5(config-if)# RACK18AS>6 [Resuming connection 6 to r6 ... ] 04:5 S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/24 S6(config-if)#sw S6(config-if)#switchport en S6(config-if)#switchport en  tru S6(config-if)#switchport trunk en S6(config-if)#switchport trunk encapsulation do S6(config-if)#switchport trunk encapsulation dot1q S6(config-if)#sw S6(config-if)#switchport no S6(config-if)#switchport nonegotiate Command rejected: Conflict between 'nonegotiate' and 'dynamic' status. S6(config-if)#sw S6(config-if)#switchport mo S6(config-if)#switchport mode tru S6(config-if)#switchport mode trunk S6(config-if)#switchport mode trunk nonegotiate S6(config-if)#sw S6(config-if)#switchport tru S6(config-if)#switchport trunk ? allowed Set allowed VLAN characteristics when interface is in trunking mode encapsulation Set trunking encapsulation when interface is in trunking mode native Set trunking native characteristics when interface is in trunking mode pruning Set pruning VLAN characteristics when interface is in trunking mode S6(config-if)#switchport trunk al S6(config-if)#switchport trunk allowed ? vlan Set allowed VLANs when interface is in trunking mode S6(config-if)#switchport trunk allowed vl S6(config-if)#switchport trunk allowed vlan ? WORD VLAN IDs of the allowed VLANs when this port is in trunking mode add add VLANs to the current list all all VLANs except all VLANs except the following none no VLANs remove remove VLANs from the current list S6(config-if)#switchport trunk allowed vlan 10,20,34 S6(config-if)#end S6#sh 04:57:01: %SYS-5-CONFIG_I: Configured from console by console S6#sh int tru Port Mode Encapsulation Status Native vlan Fa0/24 on 802.1q trunking 1 Port Vlans allowed on trunk Fa0/24 10,20,34 Port Vlans allowed and active in management domain Fa0/24 10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 10,20,34 S6# RACK18AS>5 [Resuming connection 5 to r5 ... ] 04 S5(config-if)#switchport trunk allowed vlan 10,20,34 S5(config-if)#^Z S5# S5# S5# S5# 04:57:51: %SYS-5-CONFIG_I: Configured from console by console S5#sh run int fa 0/24 Building configuration... Current configuration : 183 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport trunk allowed vlan 10,20,34 switchport mode trunk switchport nonegotiate speed 100 duplex full end S5# RACK18AS>6 [Resuming connection 6 to r6 ... ] S6#sh run int f a0/2 ^ % Invalid input detected at '^' marker. S6#sh run int f a0/2a0/2 a0/24 Building configuration... Current configuration : 183 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport trunk allowed vlan 10,20,34 switchport mode trunk switchport nonegotiate speed 100 duplex full end S6#sh int tu ru Port Mode Encapsulation Status Native vlan Fa0/24 on 802.1q trunking 1 Port Vlans allowed on trunk Fa0/24 10,20,34 Port Vlans allowed and active in management domain Fa0/24 10,20,34 Port Vlans in spanning tree forwarding state and not pruned Fa0/24 10,20,34 S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 120 R S 2611XM Fas 0/1 R1 Fas 0/1 155 R 2611 Eth 0/1 S5 Fas 0/24 141 S I WS-C3550-2Fas 0/24 R4 Fas 0/4 142 R 3620 Fas 0/0 S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 165 R S 2611XM Fas 0/1 R1 Fas 0/1 140 R 2611 Eth 0/1 S5 Fas 0/24 127 S I WS-C3550-2Fas 0/24 R4 Fas 0/4 128 R 3620 Fas 0/0 S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 163 R S 2611XM Fas 0/1 R1 Fas 0/1 138 R 2611 Eth 0/1 S5 Fas 0/24 125 S I WS-C3550-2Fas 0/24 R4 Fas 0/4 126 R 3620 Fas 0/0 S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 160 R S 2611XM Fas 0/1 R1 Fas 0/1 135 R 2611 Eth 0/1 S5 Fas 0/24 122 S I WS-C3550-2Fas 0/24 R4 Fas 0/4 122 R 3620 Fas 0/0 S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 158 R S 2611XM Fas 0/1 R1 Fas 0/1 133 R 2611 Eth 0/1 S5 Fas 0/24 120 S I WS-C3550-2Fas 0/24 R4 Fas 0/4 121 R 3620 Fas 0/0 S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 156 R S 2611XM Fas 0/1 R1 Fas 0/1 132 R 2611 Eth 0/1 S5 Fas 0/24 178 S I WS-C3550-2Fas 0/24 R4 Fas 0/4 119 R 3620 Fas 0/0 S6# S6# S6# S6# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/0 Building configuration... Current configuration : 126 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue end R3# RACK18AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run int s 1/0.1 Building configuration... Current configuration : 111 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay interface-dlci 203 end R2# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1#sh run int s 0/0.1 Building configuration... Current configuration : 118 bytes ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 end R1# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3# RACK18AS>7 % 7 is not an open connection RACK18AS> [Resuming connection 3 to r3 ... ] R3# RACK18AS>r7 Translating "r7" Trying R7 (1.1.1.1, 2007)... Open ! ************************************************************** Global Knowledge Hands-On Labs Access Server Access is restricted to Global Knowledge CCIE Students ************************************************************** Please re-enter your password. (This is the same password you used to log onto the Lab website.) If you see a username prompt, please wait 40 seconds and try again. If the username prompt persists, please reset equipment from your "Pod x" link. User Access Verification Password: Password OK Router>en Router# Router# Router# Router# Router# Router#confi t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int s 1/0 Router(config-if)#ip add 1 7.7.7.7 12  255.255.255.0 Router(config-if)#no shut Router(config-if)#encap fram Router(config-if)#^Z Router# *Mar 1 04:58:18.439: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up *Mar 1 04:58:19.441: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up *Mar 1 04:58:19.906: %SYS-5-CONFIG_I: Configured from console by console RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#sh fram pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 3 0 0 0 Switched 0 0 0 0 Unused 0 0 0 0 DLCI = 301, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 321 output pkts 23 in bytes 102908 out bytes 782 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 23 out bcast bytes 782 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 04:57:47, last time pvc status changed 04:57:27 --More--   DLCI = 302, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 25 output pkts 12 in bytes 850 out bytes 408 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 12 out bcast bytes 408 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 04:57:54, last time pvc status changed 04:57:34 --More--   DLCI = 307, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 1 output pkts 1 in bytes 34 out bytes 34 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1 out bcast bytes 34 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 04:57:58, last time pvc status changed 00:00:17 R3#sh fram map Serial1/0 (up): ip 7.7.7.7 dlci 307(0x133,0x4C30), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa    s 1/0 R3(config-if)#no fram inv R3(config-if)#no fram inverse-arp R3(config-if)#^Z R3#sh *Mar 1 05:00:08.435: %SYS-5-CONFIG_I: Configured from console by console R3#sh fram map Serial1/0 (up): ip 7.7.7.7 dlci 307(0x133,0x4C30), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), dynamic, broadcast,, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#clea fram map ? % Unrecognized command R3#clea fram map        R3#clea frame-relay ? counter Clear Frame Relay counters inarp Clear inverse ARP entries from the map table R3#clea frame-relay in R3#clea frame-relay inarp ? interface Frame Relay Interface R3#clea frame-relay inarp R3#clea frame-relay inarp sh fram map  R3#sh fram map Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#sh fram map Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#sh fram map Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#sh fram map Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#sh fram map Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#sh fram map Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#sh fram map Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), dynamic, broadcast,, status defined, active R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#fram map ip 208.28.1.1 301 br R3(config-if)#fram map ip 208.28.1.1 301 broadcast R3(config-if)#fram map ip 208.28.1.1 301 broadcast 1 broadcast 2 broadcast  302 broadcast 3 302 broadcast  R3(config-if)#^Z R3#sh *Mar 1 05:01:43.107: %SYS-5-CONFIG_I: Configured from console by console R3#sh fram map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), static, broadcast, CISCO, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), static, broadcast, CISCO, status defined, active R3#sh fram map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), static, broadcast, CISCO, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), static, broadcast, CISCO, status defined, active R3#sh fram map Serial1/0 (up): ip 208.28.1.1 dlci 301(0x12D,0x48D0), static, broadcast, CISCO, status defined, active Serial1/0 (up): ip 208.28.1.3 dlci 302(0x12E,0x48E0), static, broadcast, CISCO, status defined, active R3#ping 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/72/81 ms R3#ping 208.28.1.1 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R3# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1#ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: .. RACK18AS>2 [Resuming connection 2 to r2 ... ] R2#deb ip icmp ICMP packet debugging is on R2# RACK18AS>1 [Resuming connection 1 to r1 ... ] ..ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: RACK18AS>2 [Resuming connection 2 to r2 ... ] R2# *Mar 1 05:02:43.886: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:02:45.902: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:02:47.901: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:02:49.904: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2# *Mar 1 05:02:51.903: ICMP: echo reply sent, src 208.28.1.3, dst 208.28.1.1 R2#u all All possible debugging has been turned off R2#deb fram pakc  ck Frame Relay packet debugging is on R2# R2# R2# R2# R2# RACK18AS>1 [Resuming connection 1 to r1 ... ] .. R1#ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: RACK18AS>2 [Resuming connection 2 to r2 ... ] * R2# *Mar 1 05:03:12.417: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:03:12.421: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:03:14.416: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:03:14.420: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:03:16.420: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:03:16.424: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:03:18.451: Serial1/0(i): dlci 203(0x30B1), pkt type 0x800, datagramsize 104 *Mar 1 05:03:18.455: Serial1/0.1:Encaps failed--no map entry link 7(IP) R2# *Mar 1 05:03:21.280: Serial1/0(i): dlci 207(0x30F1), pkt encaps 0x0300 0x8000 0x0000 0x806 (ARP), datagramsize 34 *Mar 1 05:03:21.280: Serial1/0: frame relay INARP received R2#u all All possible debugging has been turned off R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#int s 1/0.1 R2(config-subif)#do sh run int s 1/0.1 Building configuration... Current configuration : 111 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay interface-dlci 203 end R2(config-subif)#no frame-relay interface-dlci 203 R2(config-subif)#frma map      am m  ap ip 209 8.28.1.2 203 br R2(config-subif)#fram map ip 208.28.1.2 203 broadcast R2(config-subif)#fram map ip 208.28.1.2 203 broadcast             203 1 203 R2(config-subif)#^Z R2# *Mar 1 05:04:23.950: %SYS-5-CONFIG_I: Configured from console by console R2# RACK18AS>1 [Resuming connection 1 to r1 ... ] .. R1#ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/124/140 ms R1# RACK18AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s 1/0.1 Building configuration... Current configuration : 159 bytes ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 broadcast end R2# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#sh run t    int s 1/0 Building configuration... Current configuration : 244 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.3 302 broadcast no frame-relay inverse-arp end R3# R3#ping 208.289.1    8.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: .. Success rate is 0 percent (0/2) R3#deb fra pack % Ambiguous command: "deb fra pack" R3#deb fra packc pack ^ % Invalid input detected at '^' marker. R3#deb frac pack pack m pack Frame Relay packet debugging is on R3#deb fram packc pack pack ping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: *Mar 1 05:08:47.562: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:08:49.562: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:08:51.565: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:08:53.568: Serial1/0:Encaps failed--no map entry link 7(IP). *Mar 1 05:08:55.568: Serial1/0:Encaps failed--no map entry link 7(IP). Success rate is 0 percent (0/5) R3# *Mar 1 05:09:13.365: Serial1/0(i): dlci 301(0x48D1), pkt type 0x2000, datagramsize 353 R3#c o   confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#fram map ip 208.28.1.3 % Incomplete command. R3(config-if)#fram map ip 208.28.1.3   1 2 302 R3(config-if)#^Z R3#confi tping 208.28.1.2 *Mar 1 05:09:53.182: %SYS-5-CONFIG_I: Configured from console by console R3#ping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !! *Mar 1 05:09:55.486: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:09:55.534: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 60 *Mar 1 05:09:55.554: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:09:55.554: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:09:55.610: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:09:55.614: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:09:55.670: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/117/124 ms R3# *Mar 1 05:09:55.670: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:09:55.730: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:09:55.730: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:09:55.786: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:09:55.790: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:09:55.846: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:09:55.846: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 R3# *Mar 1 05:09:55.902: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:09:55.906: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:09:55.963: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:09:55.963: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:09:56.023: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 *Mar 1 05:09:56.023: Serial1/0(o): dlci 302(0x48E1), pkt type 0x800(IP), datagramsize 104 *Mar 1 05:09:56.079: Serial1/0(i): dlci 302(0x48E1), pkt type 0x800, datagramsize 104 R3#u all All possible debugging has been turned off R3#u allping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/114/116 ms R3#sh run int s 1/0 Building configuration... Current configuration : 279 bytes ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 broadcast no frame-relay inverse-arp end R3#conif t ^ % Invalid input detected at '^' marker. R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#user One pass For0 -The-Money R3(config)#int s 1/2 R3(config-if)#shut R3(config-if)# *Mar 1 05:12:32.587: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 05:12:33.589: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#encap ppp R3(config-if)#auth    ppp authen ? chap Challenge Handshake Authentication Protocol (CHAP) eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) pap Password Authentication Protocol (PAP) R3(config-if)#ppp authen pap R3(config-if)#ppp pap se R3(config-if)#ppp pap sent-username Two pass R3(config-if)#ppp pap sent-username Two password For-The-Showe  R3(config-if)# RACK18AS>2 [Resuming connection 2 to r2 ... ] * R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#user Two pass For-The-Show ? LINE R2(config)#user Two pass For-The-Show   R2(config)#int s 1/2 R2(config-if)#encap ppp R2(config-if)#ppp authe pap R2(config-if)#ppp pap sen One pass For-The-Money R2(config-if)# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do s deb pp   authen PPP authentication debugging is on R3(config-if)#no shut R3(config-if)# *Mar 1 05:17:21.261: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:17:21.289: Se1/2 PPP: Using default call direction *Mar 1 05:17:21.293: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:17:21.293: Se1/2 PPP: Session handle[CC000000] Session id[1] *Mar 1 05:17:21.293: Se1/2 PPP: Authorization required *Mar 1 05:17:21.305: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:17:21.309: Se1/2 PAP: Using password from interface PAP *Mar 1 05:17:21.309: Se1/2 PAP: O AUTH-REQ id 1 len 21 from "Two" *Mar 1 05:17:21.313: Se1/2 PAP: I AUTH-REQ id 1 len 22 from "One" *Mar 1 05:17:21.313: Se1/2 PAP: Authenticating peer One *Mar 1 05:17:21.321: Se1/2 PPP: Sent PAP LOGIN Request R3(config-if)# *Mar 1 05:17:21.321: Se1/2 PPP: Received LOGIN Response PASS *Mar 1 05:17:21.325: Se1/2 PPP: Sent LCP AUTHOR Request *Mar 1 05:17:21.325: Se1/2 PPP: Sent IPCP AUTHOR Request *Mar 1 05:17:21.325: Se1/2 LCP: Received AAA AUTHOR Response PASS *Mar 1 05:17:21.329: Se1/2 IPCP: Received AAA AUTHOR Response PASS *Mar 1 05:17:21.329: Se1/2 PAP: O AUTH-ACK id 1 len 5 *Mar 1 05:17:21.329: Se1/2 PAP: I AUTH-ACK id 1 len 5 *Mar 1 05:17:21.329: Se1/2 PPP: Sent CDPCP AUTHOR Request *Mar 1 05:17:21.333: Se1/2 CDPCP: Received AAA AUTHOR Response PASS *Mar 1 05:17:21.337: Se1/2 PPP: Sent IPCP AUTHOR Request R3(config-if)# *Mar 1 05:17:22.330: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3(config-if)#shut R3(config-if)#no *Mar 1 05:18:36.812: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 05:18:37.814: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#no authen papa ^ % Invalid input detected at '^' marker. R3(config-if)#no authen papa  ^ % Invalid input detected at '^' marker. R3(config-if)#[Ano authen papno pauthen pappauthen pappauthen pap authen pap R3(config-if)# RACK18AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 05:17:2 R2(config-if)#ppp ? accm Set initial Async Control Character Map accounting Set PPP network accounting method acfc Options for HDLC Address & Control Field Compression authentication Set PPP link authentication method authorization Set PPP network authorization method bridge Enable PPP bridge translation caller Caller option when no CLID is available chap Set CHAP authentication parameters direction Override default PPP direction dnis Authentication via DNIS before LCP eap Set EAP authentication parameters encrypt Enable PPP encryption ipcp Set IPCP negotiation options iphc Set IPCP Header Compression control options lcp PPP LCP configuration link Set miscellaneous link parameters loopback PPP loopback options max-bad-auth Allow multiple authentication failures max-configure Number of conf-reqs sent before assuming peer is unable to respond max-failure Number of conf-naks sent before assuming configuration is not converging --More--   max-terminate Number of term-reqs sent before assuming peer is unable to respond ms-chap Set MS-CHAP authentication parameters ms-chap-v2 Set MS-CHAP-V2 authentication parameters multilink Make interface multilink capable pap Set PAP authentication parameters pfc Options for Protocol Field Compression quality Set parameters related to Link Quality Monitoring (LQM) reliable-link Use LAPB with PPP to provide a reliable link timeout Set PPP timeout parameters R2(config-if)#ppp authen ? chap Challenge Handshake Authentication Protocol (CHAP) eap Extensible Authentication Protocol (EAP) ms-chap Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) ms-chap-v2 Microsoft CHAP Version 2 (MS-CHAP-V2) pap Password Authentication Protocol (PAP) R2(config-if)#ppp authen "pap           pap ? refuse Refuse to authenticate using PAP sent-username Set outbound PAP username wait Wait for caller to authenticate first R2(config-if)#ppp pap ref R2(config-if)#ppp pap refuse > ? callin Refuse to authenticate on incoming call only R2(config-if)#ppp pap refuse            authen pap op R2(config-if)#ppp authen pap optional R2(config-if)# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do u all All possible debugging has been turned off R3(config-if)#du o deb ppp neo deb ppp neo ^ % Invalid input detected at '^' marker. R3(config-if)#do deb ppp neo  PPP protocol negotiation debugging is on R3(config-if)#no shut R3(config-if)# *Mar 1 05:20:45.303: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:20:45.327: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:20:45.351: Se1/2 PPP: Outbound cdp packet dropped R3(config-if)# *Mar 1 05:20:47.278: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:20:47.278: Se1/2 PPP: Using default call direction *Mar 1 05:20:47.278: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:20:47.278: Se1/2 PPP: Session handle[69000001] Session id[2] *Mar 1 05:20:47.278: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 05:20:47.278: Se1/2 LCP: O CONFREQ [Closed] id 2 len 10 *Mar 1 05:20:47.278: Se1/2 LCP: MagicNumber 0x1485E887 (0x05061485E887) *Mar 1 05:20:47.286: Se1/2 LCP: I CONFREQ [REQsent] id 2 len 14 *Mar 1 05:20:47.286: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:20:47.286: Se1/2 LCP: MagicNumber 0x1485F3F2 (0x05061485F3F2) *Mar 1 05:20:47.286: Se1/2 LCP: O CONFACK [REQsent] id 2 len 14 *Mar 1 05:20:47.290: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:20:47.290: Se1/2 LCP: MagicNumber 0x1485F3F2 (0x05061485F3F2) *Mar 1 05:20:47.290: Se1/2 LCP: I CONFACK [ACKsent] id 2 len 10 *Mar 1 05:20:47 R3(config-if)#.290: Se1/2 LCP: MagicNumber 0x1485E887 (0x05061485E887) *Mar 1 05:20:47.290: Se1/2 LCP: State is Open *Mar 1 05:20:47.290: Se1/2 PPP: Phase is AUTHENTICATING, by the peer *Mar 1 05:20:47.290: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:20:47.290: Se1/2 PAP: Using password from interface PAP *Mar 1 05:20:47.294: Se1/2 PAP: O AUTH-REQ id 2 len 21 from "Two" *Mar 1 05:20:47.306: Se1/2 PAP: I AUTH-ACK id 2 len 5 *Mar 1 05:20:47.306: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:20:47.306: Se1/2 PPP: Phase is ESTABLISHING, Finish LCP *Mar 1 05:20:47.306: Se1/2 PPP: Phase is UP *Mar 1 05:20:47.310: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 05:20:47.310: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:20:47.310: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 05:20:47.310: Se1/2 PPP: Process pending ncp packets *Mar 1 05:20:47.310: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 05:20:47.310: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 05:20:47.314: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 05:20:47.314: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:20:47.314: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 05:20:47.314: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:20:47.318: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 05:20:47.318: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:20:47.318: Se1/2 IPCP: State is Open *Mar 1 05:20:47.322: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 05:20:47.322: Se1/2 CDPCP: State is Open *Mar 1 05:20:47.322: Se1/2 IPCP: Install route to 180.40.7.2 *Mar 1 05:20:47.326: Se1/2 IPCP: Add link info for cef entry 180.40.7.2 *Mar 1 05:20:48.308: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3(config-if)# R3(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 136 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp pap sent-username Two password 0 For-The-Show end R3(config-if)#no ppp pap sent-username Two password 0 For-The-Show R3(config-if)#shut R3(config-if)#no shut *Mar 1 05:22:43.721: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down R3(config-if)#no shut *Mar 1 05:22:43.721: Se1/2 PPP: Sending Acct Event[Down] id[4] *Mar 1 05:22:43.721: Se1/2 CDPCP: State is Closed *Mar 1 05:22:43.721: Se1/2 IPCP: State is Closed *Mar 1 05:22:43.721: Se1/2 IPCP: Remove link info for cef entry 180.40.7.2 *Mar 1 05:22:43.721: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:22:43.725: Se1/2 LCP: State is Closed *Mar 1 05:22:43.725: Se1/2 PPP: Phase is DOWN *Mar 1 05:22:43.725: Se1/2 IPCP: Remove route to 180.40.7.2 *Mar 1 05:22:44.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#no shut R3(config-if)# *Mar 1 05:22:47.551: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:22:47.575: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:22:47.599: Se1/2 PPP: Outbound cdp packet dropped R3(config-if)# *Mar 1 05:22:49.527: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:22:49.527: Se1/2 PPP: Using default call direction *Mar 1 05:22:49.527: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:22:49.527: Se1/2 PPP: Session handle[15000002] Session id[3] *Mar 1 05:22:49.527: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 05:22:49.527: Se1/2 LCP: O CONFREQ [Closed] id 3 len 10 *Mar 1 05:22:49.531: Se1/2 LCP: MagicNumber 0x1487C611 (0x05061487C611) *Mar 1 05:22:49.531: Se1/2 LCP: I CONFREQ [REQsent] id 3 len 14 *Mar 1 05:22:49.531: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:22:49.531: Se1/2 LCP: MagicNumber 0x1487D174 (0x05061487D174) *Mar 1 05:22:49.531: Se1/2 LCP: O CONFNAK [REQsent] id 3 len 9 *Mar 1 05:22:49.531: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:22:49.535: Se1/2 LCP: I CONFACK [REQsent] id 3 len 10 *Mar 1 05:22:49.535: Se1/2 LCP: MagicNumber 0x1487C611 (0x05061487C611) *Mar 1 05:22: R3(config-if)#49.539: Se1/2 LCP: I CONFREQ [ACKrcvd] id 4 len 14 *Mar 1 05:22:49.539: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:22:49.539: Se1/2 LCP: MagicNumber 0x1487D174 (0x05061487D174) *Mar 1 05:22:49.543: Se1/2 LCP: O CONFNAK [ACKrcvd] id 4 len 9 *Mar 1 05:22:49.543: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:22:49.551: Se1/2 LCP: I CONFREQ [ACKrcvd] id 5 len 14 *Mar 1 05:22:49.551: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:22:49.551: Se1/2 LCP: MagicNumber 0x1487D174 (0x05061487D174) *Mar 1 05:22:49.551: Se1/2 LCP: O CONFNAK [ACKrcvd] id 5 len 9 *Mar 1 05:22:49.551: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:22:49.559: Se1/2 LCP: I CONFREQ [ACKrcvd] id 6 len 14 *Mar 1 05:22:49.559: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:22:49.559: Se1/2 LCP: MagicNumber 0x1487D174 (0x05061487D174) *Mar 1 05:22:49.559: Se1/2 LCP: O CONFNAK [ACKrcvd] id 6 len 9 *Mar 1 05:22:49.559: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:22:49.567: Se1/2 LCP: I CONFREQ [ACKrcvd] id 7 len 14 *Mar 1 05:22:49.567: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:22:49.567: Se1/2 LCP: MagicNumber 0x1487D174 (0x05061487D174) *Mar 1 05:22:49.571: Se1/2 LCP: O CONFNAK [ACKrcvd] id 7 len 9 *Mar 1 05:22:49.571: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:22:49.579: Se1/2 LCP: I CONFREQ [ACKrcvd] id 8 len 14 *Mar 1 05:22:49.579: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:22:49.579: Se1/2 LCP: MagicNumber 0x1487D174 (0x05061487D174) *Mar 1 05:22:49.579: Se1/2 LCP: O CONFREJ [ACKrcvd] id 8 len 8 *Mar 1 05:22:49.579: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:22:49.587: Se1/2 LCP: I CONFREQ [ACKrcvd] id 9 len 10 *Mar 1 05:22:49.587: Se1/2 LCP: MagicNumber 0x1487D174 (0x05061487D174) *Mar 1 05:22:49.587: Se1/2 LCP: O CONFACK [ACKrcvd] id 9 len 10 *Mar 1 05:22:49.587: Se1/2 LCP: MagicNumber 0x1487D174 (0x05061487D174) *Mar 1 05:22:49.587: Se1/2 LCP: State is Open *Mar 1 05:22:49.591: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:22:49.591: Se1/2 PPP: Phase is ESTABLISHING, Finish LCP *Mar 1 05:22:49.591: Se1/2 PPP: Phase is UP *Mar 1 05:22:49.591: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 05:22:49.591: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:22:49.591: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 05:22:49.595: Se1/2 PPP: Process pending ncp packets *Mar 1 05:22:49.595: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 05:22:49.595: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:22:49.599: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 05:22:49.599: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:22:49.599: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 05:22:49.599: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 05:22:49.603: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 05:22:49.603: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:22:49.603: Se1/2 IPCP: State is Open *Mar 1 05:22:49.603: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 05:22:49.603: Se1/2 CDPCP: State is Open *Mar 1 05:22:49.607: Se1/2 IPCP: Install route to 180.40.7.2 *Mar 1 05:22:49.607: Se1/2 IPCP: Add link info for cef entry 180.40.7.2 *Mar 1 05:22:50.592: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#shut R3(config-if)#ppp authen *Mar 1 05:24:41.975: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down R3(config-if)#ppp authen pap *Mar 1 05:24:41.975: Se1/2 PPP: Sending Acct Event[Down] id[5] *Mar 1 05:24:41.975: Se1/2 CDPCP: State is Closed *Mar 1 05:24:41.975: Se1/2 IPCP: State is Closed *Mar 1 05:24:41.975: Se1/2 IPCP: Remove link info for cef entry 180.40.7.2 *Mar 1 05:24:41.975: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:24:41.975: Se1/2 LCP: State is Closed *Mar 1 05:24:41.979: Se1/2 PPP: Phase is DOWN *Mar 1 05:24:41.979: Se1/2 IPCP: Remove route to 180.40.7.2 *Mar 1 05:24:42.977: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#ppp authen pap R3(config-if)#no shut R3(config-if)# *Mar 1 05:24:56.523: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:24:56.547: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:24:56.571: Se1/2 PPP: Outbound cdp packet dropped R3(config-if)# *Mar 1 05:24:58.502: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:24:58.502: Se1/2 PPP: Using default call direction *Mar 1 05:24:58.502: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:24:58.502: Se1/2 PPP: Session handle[35000003] Session id[4] *Mar 1 05:24:58.502: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 05:24:58.502: Se1/2 LCP: O CONFREQ [Closed] id 4 len 14 *Mar 1 05:24:58.502: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:24:58.506: Se1/2 LCP: MagicNumber 0x1489BDE1 (0x05061489BDE1) *Mar 1 05:24:58.506: Se1/2 LCP: I CONFREQ [REQsent] id 10 len 14 *Mar 1 05:24:58.506: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:24:58.506: Se1/2 LCP: MagicNumber 0x1489C948 (0x05061489C948) *Mar 1 05:24:58.510: Se1/2 LCP: O CONFNAK [REQsent] id 10 len 9 *Mar 1 05:24:58.510: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:24:58.514: Se1/2 LCP: I CONFACK [REQsent] id 4 len 14 *Mar 1 05:24:58.514: Se1 R3(config-if)#/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:24:58.514: Se1/2 LCP: MagicNumber 0x1489BDE1 (0x05061489BDE1) *Mar 1 05:24:58.518: Se1/2 LCP: I CONFREQ [ACKrcvd] id 11 len 14 *Mar 1 05:24:58.518: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:24:58.518: Se1/2 LCP: MagicNumber 0x1489C948 (0x05061489C948) *Mar 1 05:24:58.518: Se1/2 LCP: O CONFNAK [ACKrcvd] id 11 len 9 *Mar 1 05:24:58.518: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:24:58.526: Se1/2 LCP: I CONFREQ [ACKrcvd] id 12 len 14 *Mar 1 05:24:58.526: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:24:58.526: Se1/2 LCP: MagicNumber 0x1489C948 (0x05061489C948) *Mar 1 05:24:58.526: Se1/2 LCP: O CONFNAK [ACKrcvd] id 12 len 9 *Mar 1 05:24:58.526: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:24:58.534: Se1/2 LCP: I CONFREQ [ACKrcvd] id 13 len 14 *Mar 1 05:24:58.534: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:24:58.538: Se1/2 LCP: MagicNumber 0x1489C948 (0x05061489C948) *Mar 1 05:24:58.538: Se1/2 LCP: O CONFNAK [ACKrcvd] id 13 len 9 *Mar 1 05:24:58.538: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:24:58.546: Se1/2 LCP: I CONFREQ [ACKrcvd] id 14 len 14 *Mar 1 05:24:58.546: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:24:58.546: Se1/2 LCP: MagicNumber 0x1489C948 (0x05061489C948) *Mar 1 05:24:58.546: Se1/2 LCP: O CONFNAK [ACKrcvd] id 14 len 9 *Mar 1 05:24:58.546: Se1/2 LCP: AuthProto CHAP (0x0305C22305) *Mar 1 05:24:58.554: Se1/2 LCP: I CONFREQ [ACKrcvd] id 15 len 14 *Mar 1 05:24:58.554: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:24:58.554: Se1/2 LCP: MagicNumber 0x1489C948 (0x05061489C948) *Mar 1 05:24:58.554: Se1/2 LCP: O CONFREJ [ACKrcvd] id 15 len 8 *Mar 1 05:24:58.558: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:24:58.562: Se1/2 LCP: I CONFREQ [ACKrcvd] id 16 len 10 *Mar 1 05:24:58.562: Se1/2 LCP: MagicNumber 0x1489C948 (0x05061489C948) *Mar 1 05:24:58.566: Se1/2 LCP: O CONFACK [ACKrcvd] id 16 len 10 *Mar 1 05:24:58.566: Se1/2 LCP: MagicNumber 0x1489C948 (0x05061489C948) *Mar 1 05:24:58.566: Se1/2 LCP: State is Open *Mar 1 05:24:58.566: Se1/2 PPP: Phase is AUTHENTICATING, by this end *Mar 1 05:24:58.574: Se1/2 PAP: I AUTH-REQ id 2 len 22 from "One" *Mar 1 05:24:58.574: Se1/2 PAP: Authenticating peer One *Mar 1 05:24:58.574: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:24:58.574: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:24:58.578: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:24:58.578: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:24:58.582: Se1/2 PAP: O AUTH-ACK id 2 len 5 *Mar 1 05:24:58.582: Se1/2 PPP: Phase is UP *Mar 1 05:24:58.582: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 05:24:58.582: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:24:58.586: Se1/2 PPP: Process pending ncp packets *Mar 1 05:24:58.586: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 05:24:58.590: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 05:24:58.590: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:24:58.590: Se1/2 AAA/AUTHOR/IPCP: Start. Her address 180.40.7.2, we want 0.0.0.0 *Mar 1 05:24:58.590: Se1/2 CDPCP: I CONFREQ [REQsent] id 1 len 4 *Mar 1 05:24:58.594: Se1/2 CDPCP: O CONFACK [REQsent] id 1 len 4 *Mar 1 05:24:58.594: Se1/2 AAA/AUTHOR/IPCP: Reject 180.40.7.2, using 0.0.0.0 *Mar 1 05:24:58.594: Se1/2 AAA/AUTHOR/IPCP: Done. Her address 180.40.7.2, we want 0.0.0.0 *Mar 1 05:24:58.598: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 05:24:58.598: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:24:58.598: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 05:24:58.598: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:24:58.598: Se1/2 IPCP: State is Open *Mar 1 05:24:58.598: Se1/2 CDPCP: I CONFACK [ACKsent] id 1 len 4 *Mar 1 05:24:58.598: Se1/2 CDPCP: State is Open *Mar 1 05:24:58.602: Se1/2 IPCP: Install route to 180.40.7.2 *Mar 1 05:24:58.606: Se1/2 IPCP: Add link info for cef entry 180.40.7.2 *Mar 1 05:24:59.584: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3(config-if)# R3(config-if)#shut R3(config-if)#shutno shutshut   *Mar 1 05:25:15.947: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down R3(config-if)# *Mar 1 05:25:15.947: Se1/2 PPP: Sending Acct Event[Down] id[6] *Mar 1 05:25:15.947: Se1/2 CDPCP: State is Closed *Mar 1 05:25:15.947: Se1/2 IPCP: State is Closed *Mar 1 05:25:15.947: Se1/2 IPCP: Remove link info for cef entry 180.40.7.2 *Mar 1 05:25:15.951: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:25:15.951: Se1/2 LCP: State is Closed *Mar 1 05:25:15.951: Se1/2 PPP: Phase is DOWN *Mar 1 05:25:15.951: Se1/2 IPCP: Remove route to 180.40.7.2 *Mar 1 05:25:16.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#I CONFREQ [ACKrcvd] id 16 len 10 ^ % Invalid input detected at '^' marker. R3(config)#*Mar 1 05:24:58.562: Se1/2 LCP: MagicNumber 0x1489C948 (0x0506$24:58.562: Se1/2 LCP: MagicNumber 0x1489C948 (0x05061 489C948)                                                                *Mar 1 05          I CONFREQ [ACKrcvd] id 16 len 10shut no shutppp authen papshut no shutshut no ppp pap sent-username Two password 0 For-The-Show no ppp pap sent-username Two password 0 For-The-Sho  ppp pap sent-username Two password 0 For-The-Sho  ^ % Invalid input detected at '^' marker. R3(config)# ppp pap sent-username Two password 0 For-The-ShoI CONFREQ [ACKrcvd] id 16 len 10  ppp pap sent-username Two password 0 For-The-Shoi                                                   int s 1/2 R3(config-if)#int s 1/2 ppp pap sent-username Two password 0 For-The-Sho R3(config-if)#no shut R3(config-if)# *Mar 1 05:25:46.681: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:25:46.705: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:25:46.729: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:25:47.951: Se1/2 LCP: I CONFREQ [Closed] id 17 len 14 *Mar 1 05:25:47.951: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:47.951: Se1/2 LCP: MagicNumber 0x148A8A6E (0x0506148A8A6E) *Mar 1 05:25:47.951: Se1/2 LCP: Fast-starting PPP *Mar 1 05:25:47.955: Se1/2 PPP: Using default call direction *Mar 1 05:25:47.955: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:25:47.955: Se1/2 PPP: Session handle[F9000004] Session id[4] *Mar 1 05:25:47.955: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 05:25:47.955: Se1/2 LCP: O CONFREQ [Closed] id 5 len 14 *Mar 1 05:25:47.955: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:47.955: Se1/2 LCP: MagicNumber 0x148A7F0F (0x0506148A7F0F) *Mar 1 05:25:47.959: Se1/2 LCP: O CONFACK [REQsent] id 17 len 14 R3(config-if)#*Mar 1 05:25:47.959: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:47.959: Se1/2 LCP: MagicNumber 0x148A8A6E (0x0506148A8A6E) *Mar 1 05:25:47.959: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:25:47.963: Se1/2 LCP: I CONFACK [ACKsent] id 5 len 14 *Mar 1 05:25:47.963: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:47.967: Se1/2 LCP: MagicNumber 0x148A7F0F (0x0506148A7F0F) *Mar 1 05:25:47.967: Se1/2 LCP: State is Open *Mar 1 05:25:47.967: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:25:47.967: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:25:47.967: Se1/2 PAP: Using password from interface PAP *Mar 1 05:25:47.967: Se1/2 PAP: O AUTH-REQ id 3 len 20 from "Two" *Mar 1 05:25:47.967: Se1/2 PAP: I AUTH-REQ id 3 len 22 from "One" *Mar 1 05:25:47.971: Se1/2 PAP: Authenticating peer One *Mar 1 05:25:47.971: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:25:47.971: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:25:47.971: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:25:47.975: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:25:47.975: Se1/2 PAP: O AUTH-ACK id 3 len 5 *Mar 1 05:25:47.979: Se1/2 PAP: I AUTH-NAK id 3 len 26 msg is "Authentication failed" *Mar 1 05:25:47.983: Se1/2 LCP: I TERMREQ [Open] id 18 len 4 *Mar 1 05:25:47.983: Se1/2 LCP: O TERMACK [Open] id 18 len 4 *Mar 1 05:25:47.983: Se1/2 PPP: Sending Acct Event[Down] id[7] *Mar 1 05:25:47.983: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:25:49.990: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:25:49.990: Se1/2 LCP: State is Closed *Mar 1 05:25:49.990: Se1/2 PPP: Phase is DOWN *Mar 1 05:25:49.990: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:25:49.990: Se1/2 LCP: State is Listen *Mar 1 05:25:50.007: Se1/2 LCP: I CONFREQ [Listen] id 19 len 14 *Mar 1 05:25:50.007: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:50.007: Se1/2 LCP: MagicNumber 0x148A9276 (0x0506148A9276) *Mar 1 05:25:50.007: Se1/2 LCP: O CONFREQ [Listen] id 6 len 14 *Mar 1 05:25:50.011: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:50.011: Se1/2 LCP: MagicNumber 0x148A8714 (0x0506148A8714) *Mar 1 05:25:50.011: Se1/2 LCP: O CONFACK [Listen] id 19 len 14 *Mar 1 05:25:50.011: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:50.011: Se1/2 LCP: MagicNumber 0x148A9276 (0x0506148A9276) *Mar 1 05:25:50.019: Se1/2 LCP: I CONFACK [ACKsent] id 6 len 14 *Mar 1 05:25:50.019: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:50.019: Se1/2 LCP: MagicNumber 0x148A8714 (0x0506148A8714) *Mar 1 05:25:50.019: Se1/2 LCP: State is Open *Mar 1 05:25:50.019: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:25:50.019: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:25:50.019: Se1/2 PAP: Using password from interface PAP *Mar 1 05:25:50.019: Se1/2 PAP: O AUTH-REQ id 4 len 20 from "Two" *Mar 1 05:25:50.023: Se1/2 PAP: I AUTH-REQ id 4 len 22 from "One" *Mar 1 05:25:50.023: Se1/2 PAP: Authenticating peer One *Mar 1 05:25:50.023: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:25:50.023: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:25:50.027: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:25:50.027: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:25:50.031: Se1/2 PAP: O AUTH-ACK id 4 len 5 *Mar 1 05:25:50.035: Se1/2 PAP: I AUTH-NAK id 4 len 26 msg is "Authentication failed" *Mar 1 05:25:50.035: Se1/2 LCP: I TERMREQ [Open] id 20 len 4 *Mar 1 05:25:50.035: Se1/2 LCP: O TERMACK [Open] id 20 len 4 *Mar 1 05:25:50.035: Se1/2 PPP: Sending Acct Event[Down] id[8] *Mar 1 05:25:50.039: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:25:52.038: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:25:52.038: Se1/2 LCP: State is Closed *Mar 1 05:25:52.038: Se1/2 PPP: Phase is DOWN *Mar 1 05:25:52.038: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:25:52.038: Se1/2 LCP: State is Listen *Mar 1 05:25:52.054: Se1/2 LCP: I CONFREQ [Listen] id 21 len 14 *Mar 1 05:25:52.054: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:52.054: Se1/2 LCP: MagicNumber 0x148A9A77 (0x0506148A9A77) *Mar 1 05:25:52.054: Se1/2 LCP: O CONFREQ [Listen] id 7 len 14 *Mar 1 05:25:52.058: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:52.058: Se1/2 LCP: MagicNumber 0x148A8F14 (0x0506148A8F14) *Mar 1 05:25:52.058: Se1/2 LCP: O CONFACK [Listen] id 21 len 14 *Mar 1 05:25:52.058: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:52.058: Se1/2 LCP: MagicNumber 0x148A9A77 (0x0506148A9A77) *Mar 1 05:25:52.066: Se1/2 LCP: I CONFACK [ACKsent] id 7 len 14 *Mar 1 05:25:52.066: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:52.066: Se1/2 LCP: MagicNumber 0x148A8F14 (0x0506148A8F14) *Mar 1 05:25:52.066: Se1/2 LCP: State is Open *Mar 1 05:25:52.066: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:25:52.066: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:25:52.066: Se1/2 PAP: Using password from interface PAP *Mar 1 05:25:52.066: Se1/2 PAP: O AUTH-REQ id 5 len 20 from "Two" *Mar 1 05:25:52.078: Se1/2 PAP: I AUTH-REQ id 5 len 22 from "One" *Mar 1 05:25:52.078: Se1/2 PAP: Authenticating peer One *Mar 1 05:25:52.078: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:25:52.078: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:25:52.082: Se1/2 PAP: I AUTH-NAK id 5 len 26 msg is "Authentication failed" *Mar 1 05:25:52.082: Se1/2 LCP: I TERMREQ [Open] id 22 len 4 *Mar 1 05:25:52.082: Se1/2 LCP: O TERMACK [Open] id 22 len 4 *Mar 1 05:25:52.082: Se1/2 PPP: Sending Acct Event[Down] id[9] *Mar 1 05:25:52.086: Se1/2 PPP: Phase is TERMINATING R3(config-if)# R3(config-if)# *Mar 1 05:25:54.097: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:25:54.097: Se1/2 LCP: State is Closed *Mar 1 05:25:54.097: Se1/2 PPP: Phase is DOWN *Mar 1 05:25:54.101: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:25:54.101: Se1/2 LCP: State is Listen R3(config-if)# *Mar 1 05:25:56.104: Se1/2 LCP: TIMEout: State Listen *Mar 1 05:25:56.109: Se1/2 LCP: O CONFREQ [Listen] id 8 len 14 *Mar 1 05:25:56.109: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:56.109: Se1/2 LCP: MagicNumber 0x148A9EE8 (0x0506148A9EE8) *Mar 1 05:25:56.117: Se1/2 LCP: I CONFACK [REQsent] id 8 len 14 *Mar 1 05:25:56.117: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:56.117: Se1/2 LCP: MagicNumber 0x148A9EE8 (0x0506148A9EE8) *Mar 1 05:25:56.121: Se1/2 LCP: I CONFREQ [ACKrcvd] id 24 len 14 *Mar 1 05:25:56.121: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:56.121: Se1/2 LCP: MagicNumber 0x148AA277 (0x0506148AA277) *Mar 1 05:25:56.121: Se1/2 LCP: O CONFACK [ACKrcvd] id 24 len 14 *Mar 1 05:25:56.121: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:25:56.121: Se1/2 LCP: MagicNumber 0x148AA277 (0x0506148AA277) *Mar 1 05:25:56.121: Se1/2 LCP: State is Open *Mar 1 05:25:56.125: Se1/2 PPP: Phase is AUTHENTICATING, by bot R3(config-if)#h *Mar 1 05:25:56.125: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:25:56.125: Se1/2 PAP: Using password from interface PAP *Mar 1 05:25:56.125: Se1/2 PAP: O AUTH-REQ id 6 len 20 from "Two" *Mar 1 05:25:56.133: Se1/2 PAP: I AUTH-REQ id 6 len 22 from "One" *Mar 1 05:25:56.133: Se1/2 PAP: Authenticating peer One *Mar 1 05:25:56.133: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:25:56.133: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:25:56.137: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:25:56.137: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:25:56.137: Se1/2 PAP: I AUTH-NAK id 6 len 26 msg is "Authentication failed" *Mar 1 05:25:56.141: Se1/2 LCP: I TERMREQ [Open] id 25 len 4 *Mar 1 05:25:56.141: Se1/2 PAP: O AUTH-ACK id 6 len 5 *Mar 1 05:25:57.098: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3(config-if)# R3(config-if)# *Mar 1 05:25:58.128: Se1/2 LCP: I TERMREQ [Open] id 26 len 4 *Mar 1 05:25:58.132: Se1/2 LCP: O TERMACK [Open] id 26 len 4 *Mar 1 05:25:58.132: Se1/2 PPP: Sending Acct Event[Down] id[A] *Mar 1 05:25:58.132: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:25:59.133: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)# *Mar 1 05:26:00.135: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:26:00.135: Se1/2 LCP: State is Closed *Mar 1 05:26:00.135: Se1/2 PPP: Phase is DOWN *Mar 1 05:26:00.135: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:26:00.135: Se1/2 LCP: State is Listen *Mar 1 05:26:00.139: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:26:00.147: Se1/2 LCP: I CONFREQ [Listen] id 27 len 14 *Mar 1 05:26:00.147: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:00.147: Se1/2 LCP: MagicNumber 0x148ABA16 (0x0506148ABA16) *Mar 1 05:26:00.147: Se1/2 LCP: O CONFREQ [Listen] id 9 len 14 *Mar 1 05:26:00.151: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:00.151: Se1/2 LCP: MagicNumber 0x148AAEB3 (0x0506148AAEB3) *Mar 1 05:26:00.151: Se1/2 LCP: O CONFACK [Listen] id 27 len 14 *Mar 1 05:26:00.151: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:00.151: Se1/2 LCP: MagicNumber 0x148ABA16 (0x0506148ABA16) *Mar 1 05:26:00.159: Se1/2 LCP: I CONF R3(config-if)#ACK [ACKsent] id 9 len 14 *Mar 1 05:26:00.159: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:00.159: Se1/2 LCP: MagicNumber 0x148AAEB3 (0x0506148AAEB3) *Mar 1 05:26:00.159: Se1/2 LCP: State is Open *Mar 1 05:26:00.159: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:26:00.159: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:26:00.159: Se1/2 PAP: Using password from interface PAP *Mar 1 05:26:00.159: Se1/2 PAP: O AUTH-REQ id 7 len 20 from "Two" *Mar 1 05:26:00.163: Se1/2 PAP: I AUTH-REQ id 7 len 22 from "One" *Mar 1 05:26:00.163: Se1/2 PAP: Authenticating peer One *Mar 1 05:26:00.163: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:00.163: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:26:00.167: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:00.167: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:26:00.171: Se1/2 PAP: O AUTH-ACK id 7 len 5 *Mar 1 05:26:00.175: Se1/2 PAP: I AUTH-NAK id 7 len 26 msg is "Authentication failed" *Mar 1 05:26:00.175: Se1/2 LCP: I TERMREQ [Open] id 28 len 4 *Mar 1 05:26:00.175: Se1/2 LCP: O TERMACK [Open] id 28 len 4 *Mar 1 05:26:00.175: Se1/2 PPP: Sending Acct Event[Down] id[B] *Mar 1 05:26:00.179: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:26:02.182: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:26:02.182: Se1/2 LCP: State is Closed *Mar 1 05:26:02.182: Se1/2 PPP: Phase is DOWN *Mar 1 05:26:02.182: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:26:02.182: Se1/2 LCP: State is Listen *Mar 1 05:26:02.198: Se1/2 LCP: I CONFREQ [Listen] id 29 len 14 *Mar 1 05:26:02.198: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:02.198: Se1/2 LCP: MagicNumber 0x148AC21A (0x0506148AC21A) *Mar 1 05:26:02.198: Se1/2 LCP: O CONFREQ [Listen] id 10 len 14 *Mar 1 05:26:02.202: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:02.202: Se1/2 LCP: MagicNumber 0x148AB6B8 (0x0506148AB6B8) *Mar 1 05:26:02.202: Se1/2 LCP: O CONFACK [Listen] id 29 len 14 *Mar 1 05:26:02.202: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:02.202: Se1/2 LCP: MagicNumber 0x148AC21A (0x0506148AC21A) *Mar 1 05:26:02.211: Se1/2 LCP: I CONFACK [ACKsent] id 10 len 14 *Mar 1 05:26:02.211: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:02.211: Se1/2 LCP: MagicNumber 0x148AB6B8 (0x0506148AB6B8) *Mar 1 05:26:02.211: Se1/2 LCP: State is Open *Mar 1 05:26:02.211: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:26:02.211: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:26:02.211: Se1/2 PAP: Using password from interface PAP *Mar 1 05:26:02.215: Se1/2 PAP: O AUTH-REQ id 8 len 20 from "Two" *Mar 1 05:26:02.215: Se1/2 PAP: I AUTH-REQ id 8 len 22 from "One" *Mar 1 05:26:02.215: Se1/2 PAP: Authenticating peer One *Mar 1 05:26:02.215: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:02.215: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:26:02.219: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:02.219: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:26:02.223: Se1/2 PAP: O AUTH-ACK id 8 len 5 *Mar 1 05:26:02.227: Se1/2 PAP: I AUTH-NAK id 8 len 26 msg is "Authentication failed" *Mar 1 05:26:02.227: Se1/2 LCP: I TERMREQ [Open] id 30 len 4 *Mar 1 05:26:02.227: Se1/2 LCP: O TERMACK [Open] id 30 len 4 *Mar 1 05:26:02.227: Se1/2 PPP: Sending Acct Event[Down] id[C] *Mar 1 05:26:02.231: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:26:04.230: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:26:04.230: Se1/2 LCP: State is Closed *Mar 1 05:26:04.230: Se1/2 PPP: Phase is DOWN *Mar 1 05:26:04.230: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:26:04.230: Se1/2 LCP: State is Listen *Mar 1 05:26:04.246: Se1/2 LCP: I CONFREQ [Listen] id 31 len 14 *Mar 1 05:26:04.246: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:04.246: Se1/2 LCP: MagicNumber 0x148ACA1B (0x0506148ACA1B) *Mar 1 05:26:04.246: Se1/2 LCP: O CONFREQ [Listen] id 11 len 14 *Mar 1 05:26:04.250: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:04.250: Se1/2 LCP: MagicNumber 0x148ABEB8 (0x0506148ABEB8) *Mar 1 05:26:04.250: Se1/2 LCP: O CONFACK [Listen] id 31 len 14 *Mar 1 05:26:04.250: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:04.250: Se1/2 LCP: MagicNumber 0x148ACA1B (0x0506148ACA1B) *Mar 1 05:26:04.258: Se1/2 LCP: I CONFACK [ACKsent] id 11 len 14 *Mar 1 05:26:04.258: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:04.258: Se1/2 LCP: MagicNumber 0x148ABEB8 (0x0506148ABEB8) *Mar 1 05:26:04.258: Se1/2 LCP: State is Open *Mar 1 05:26:04.258: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:26:04.258: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:26:04.258: Se1/2 PAP: Using password from interface PAP *Mar 1 05:26:04.258: Se1/2 PAP: O AUTH-REQ id 9 len 20 from "Two" *Mar 1 05:26:04.262: Se1/2 PAP: I AUTH-REQ id 9 len 22 from "One" *Mar 1 05:26:04.262: Se1/2 PAP: Authenticating peer One *Mar 1 05:26:04.262: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:04.262: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:26:04.266: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:04.266: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:26:04.270: Se1/2 PAP: O AUTH-ACK id 9 len 5 *Mar 1 05:26:04.274: Se1/2 PAP: I AUTH-NAK id 9 len 26 msg is "Authentication failed" *Mar 1 05:26:04.274: Se1/2 LCP: I TERMREQ [Open] id 32 len 4 *Mar 1 05:26:04.274: Se1/2 LCP: O TERMACK [Open] id 32 len 4 *Mar 1 05:26:04.274: Se1/2 PPP: Sending Acct Event[Down] id[D] *Mar 1 05:26:04.278: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:26:06.281: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:26:06.281: Se1/2 LCP: State is Closed *Mar 1 05:26:06.281: Se1/2 PPP: Phase is DOWN *Mar 1 05:26:06.281: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:26:06.281: Se1/2 LCP: State is Listen *Mar 1 05:26:06.293: Se1/2 LCP: I CONFREQ [Listen] id 33 len 14 *Mar 1 05:26:06.293: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:06.293: Se1/2 LCP: MagicNumber 0x148AD21B (0x0506148AD21B) *Mar 1 05:26:06.293: Se1/2 LCP: O CONFREQ [Listen] id 12 len 14 *Mar 1 05:26:06.297: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:06.297: Se1/2 LCP: MagicNumber 0x148AC6B8 (0x0506148AC6B8) *Mar 1 05:26:06.297: Se1/2 LCP: O CONFACK [Listen] id 33 len 14 *Mar 1 05:26:06.297: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:06.297: Se1/2 LCP: MagicNumber 0x148AD21B (0x0506148AD21B) *Mar 1 05:26:06.305: Se1/2 LCP: I CONFACK [ACKsent] id 12 len 14 *Mar 1 05:26:06.305: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:06.305: Se1/2 LCP: MagicNumber 0x148AC6B8 (0x0506148AC6B8) *Mar 1 05:26:06.305: Se1/2 LCP: State is Open *Mar 1 05:26:06.305: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:26:06.305: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:26:06.305: Se1/2 PAP: Using password from interface PAP *Mar 1 05:26:06.305: Se1/2 PAP: O AUTH-REQ id 10 len 20 from "Two" *Mar 1 05:26:06.309: Se1/2 PAP: I AUTH-REQ id 10 len 22 from "One" *Mar 1 05:26:06.309: Se1/2 PAP: Authenticating peer One *Mar 1 05:26:06.309: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:06.309: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:26:06.313: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:06.313: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:26:06.317: Se1/2 PAP: O AUTH-ACK id 10 len 5 *Mar 1 05:26:06.321: Se1/2 PAP: I AUTH-NAK id 10 len 26 msg is "Authentication failed" *Mar 1 05:26:06.321: Se1/2 LCP: I TERMREQ [Open] id 34 len 4 *Mar 1 05:26:06.321: Se1/2 LCP: O TERMACK [Open] id 34 len 4 *Mar 1 05:26:06.321: Se1/2 PPP: Sending Acct Event[Down] id[E] *Mar 1 05:26:06.325: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:26:08.329: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:26:08.329: Se1/2 LCP: State is Closed *Mar 1 05:26:08.329: Se1/2 PPP: Phase is DOWN *Mar 1 05:26:08.329: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:26:08.329: Se1/2 LCP: State is Listen *Mar 1 05:26:08.341: Se1/2 LCP: I CONFREQ [Listen] id 35 len 14 *Mar 1 05:26:08.341: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:08.341: Se1/2 LCP: MagicNumber 0x148ADA1C (0x0506148ADA1C) *Mar 1 05:26:08.341: Se1/2 LCP: O CONFREQ [Listen] id 13 len 14 *Mar 1 05:26:08.345: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:08.345: Se1/2 LCP: MagicNumber 0x148ACEB9 (0x0506148ACEB9) *Mar 1 05:26:08.345: Se1/2 LCP: O CONFACK [Listen] id 35 len 14 *Mar 1 05:26:08.345: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:08.345: Se1/2 LCP: MagicNumber 0x148ADA1C (0x0506148ADA1C) *Mar 1 05:26:08.353: Se1/2 LCP: I CONFACK [ACKsent] id 13 len 14 *Mar 1 05:26:08.353: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:08.353: Se1/2 LCP: MagicNumber 0x148ACEB9 (0x0506148ACEB9) *Mar 1 05:26:08.353: Se1/2 LCP: State is Open *Mar 1 05:26:08.353: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:26:08.353: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:26:08.353: Se1/2 PAP: Using password from interface PAP *Mar 1 05:26:08.353: Se1/2 PAP: O AUTH-REQ id 11 len 20 from "Two" *Mar 1 05:26:08.357: Se1/2 PAP: I AUTH-REQ id 11 len 22 from "One" *Mar 1 05:26:08.357: Se1/2 PAP: Authenticating peer One *Mar 1 05:26:08.357: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:08.357: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:26:08.361: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:08.361: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:26:08.365: Se1/2 PAP: O AUTH-ACK id 11 len 5 *Mar 1 05:26:08.369: Se1/2 PAP: I AUTH-NAK id 11 len 26 msg is "Authentication failed" *Mar 1 05:26:08.369: Se1/2 LCP: I TERMREQ [Open] id 36 len 4 *Mar 1 05:26:08.369: Se1/2 LCP: O TERMACK [Open] id 36 len 4 *Mar 1 05:26:08.369: Se1/2 PPP: Sending Acct Event[Down] id[F] *Mar 1 05:26:08.373: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:26:10.376: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:26:10.376: Se1/2 LCP: State is Closed *Mar 1 05:26:10.376: Se1/2 PPP: Phase is DOWN *Mar 1 05:26:10.376: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:26:10.376: Se1/2 LCP: State is Listen *Mar 1 05:26:10.388: Se1/2 LCP: I CONFREQ [Listen] id 37 len 14 *Mar 1 05:26:10.388: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:10.388: Se1/2 LCP: MagicNumber 0x148AE21C (0x0506148AE21C) *Mar 1 05:26:10.388: Se1/2 LCP: O CONFREQ [Listen] id 14 len 14 *Mar 1 05:26:10.392: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:10.392: Se1/2 LCP: MagicNumber 0x148AD6B9 (0x0506148AD6B9) *Mar 1 05:26:10.392: Se1/2 LCP: O CONFACK [Listen] id 37 len 14 *Mar 1 05:26:10.392: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:10.392: Se1/2 LCP: MagicNumber 0x148AE21C (0x0506148AE21C) *Mar 1 05:26:10.400: Se1/2 LCP: I CONFACK [ACKsent] id 14 len 14 *Mar 1 05:26:10.400: Se1/2 LCP RACK18AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 R2(config-if)#shut R2(config-if)# RACK18AS>3 [Resuming connection 3 to r3 ... ] roto PAP (0x0304C023) *1] *Mar 1 05:26:12.467: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:26:14.471: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:26:14.471: Se1/2 LCP: State is Closed *Mar 1 05:26:14.471: Se1/2 PPP: Phase is DOWN *Mar 1 05:26:14.471: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:26:14.471: Se1/2 LCP: State is Listen *Mar 1 05:26:14.483: Se1/2 LCP: I CONFREQ [Listen] id 41 len 14 *Mar 1 05:26:14.483: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:14.483: Se1/2 LCP: MagicNumber 0x148AF21D (0x0506148AF21D) *Mar 1 05:26:14.483: Se1/2 LCP: O CONFREQ [Listen] id 16 len 14 *Mar 1 05:26:14.487: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:14.487: Se1/2 LCP: MagicNumber 0x148AE6BA (0x0506148AE6BA) *Mar 1 05:26:14.487: Se1/2 LCP: O CONFACK [Listen] id 41 len 14 *Mar 1 05:26:14.487: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:14.487: Se1/2 LCP: MagicNumber 0x148AF21D (0x0506148AF21D) *Mar 1 05:26:14.495: Se1/2 LCP: I CONFACK [ACKsent] id 16 len 14 *Mar 1 05:26:14.495: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:14.495: Se1/2 LCP: MagicNumber 0x148AE6BA (0x0506148AE6BA) *Mar 1 05:26:14.495: Se1/2 LCP: State is Open *Mar 1 05:26:14.495: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:26:14.495: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:26:14.495: Se1/2 PAP: Using password from interface PAP *Mar 1 05:26:14.495: Se1/2 PAP: O AUTH-REQ id 14 len 20 from "Two" *Mar 1 05:26:14.499: Se1/2 PAP: I AUTH-REQ id 14 len 22 from "One" *Mar 1 05:26:14.499: Se1/2 PAP: Authenticating peer One *Mar 1 05:26:14.499: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:14.499: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:26:14.503: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:14.503: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:26:14.507: Se1/2 PAP: O AUTH-ACK id 14 len 5 *Mar 1 05:26:14.511: Se1/2 PAP: I AUTH-NAK id 14 len 26 msg is "Authentication failed" *Mar 1 05:26:14.511: Se1/2 LCP: I TERMREQ [Open] id 42 len 4 *Mar 1 05:26:14.511: Se1/2 LCP: O TERMACK [Open] id 42 len 4 *Mar 1 05:26:14.511: Se1/2 PPP: Sending Acct Event[Down] id[12] *Mar 1 05:26:14.515: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:26:16.518: Se1/2 LCP: TIMEout: State TERMsent *Mar 1 05:26:16.518: Se1/2 LCP: State is Closed *Mar 1 05:26:16.518: Se1/2 PPP: Phase is DOWN *Mar 1 05:26:16.518: Se1/2 PPP: Phase is ESTABLISHING, Passive Open *Mar 1 05:26:16.518: Se1/2 LCP: State is Listen *Mar 1 05:26:16.534: Se1/2 LCP: I CONFREQ [Listen] id 43 len 14 *Mar 1 05:26:16.534: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:16.534: Se1/2 LCP: MagicNumber 0x148AFA21 (0x0506148AFA21) *Mar 1 05:26:16.534: Se1/2 LCP: O CONFREQ [Listen] id 17 len 14 *Mar 1 05:26:16.538: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:16.538: Se1/2 LCP: MagicNumber 0x148AEEBE (0x0506148AEEBE) *Mar 1 05:26:16.538: Se1/2 LCP: O CONFACK [Listen] id 43 len 14 *Mar 1 05:26:16.538: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:16.538: Se1/2 LCP: MagicNumber 0x148AFA21 (0x0506148AFA21) *Mar 1 05:26:16.546: Se1/2 LCP: I CONFACK [ACKsent] id 17 len 14 *Mar 1 05:26:16.546: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:16.546: Se1/2 LCP: MagicNumber 0x148AEEBE (0x0506148AEEBE) *Mar 1 05:26:16.546: Se1/2 LCP: State is Open *Mar 1 05:26:16.546: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:26:16.546: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:26:16.546: Se1/2 PAP: Using password from interface PAP *Mar 1 05:26:16.546: Se1/2 PAP: O AUTH-REQ id 15 len 20 from "Two" *Mar 1 05:26:16.550: Se1/2 PAP: I AUTH-REQ id 15 len 22 from "One" *Mar 1 05:26:16.550: Se1/2 PAP: Authenticating peer One *Mar 1 05:26:16.550: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:16.550: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:26:16.554: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:16.554: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:26:16.558: Se1/2 PAP: O AUTH-ACK id 15 len 5 *Mar 1 05:26:16.562: Se1/2 PAP: I AUTH-NAK id 15 len 26 msg is "Authentication failed" *Mar 1 05:26:16.562: Se1/2 LCP: I TERMREQ [Open] id 44 len 4 *Mar 1 05:26:16.562: Se1/2 LCP: O TERMACK [Open] id 44 len 4 *Mar 1 05:26:16.562: Se1/2 PPP: Sending Acct Event[Down] id[13] *Mar 1 05:26:16.566: Se1/2 PPP: Phase is TERMINATING *Mar 1 05:26:18.521: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down *Mar 1 05:26:18.521: Se1/2 LCP: State is Closed *Mar 1 05:26:18.521: Se1/2 PPP: Phase is DOWN R3(config-if)# R3(config-if)#no shut ppp pap sent-username Two password 0 For-The-Show R3(config-if)# ppp pap sent-username Two password 0 For-The-Showno shut  ppp pap sent-username Two password 0 For-The-Shoint s 1/2  ppp pap sent-username Two password 0 For-The-ShoI CONFREQ [ACKrcvd] id 16 len 10 shut no shutppp authen pap op R3(config-if)#ppp authen pap optional R3(config-if)#^Z R3# RACK18AS>23 % 23 is not an open connection RACK18AS> [Resuming connection 3 to r3 ... ] *Mar 1 05:26:48.743: %SYS-5-CONFIG_I: Configured from console by console R3# RACK18AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 R2(config-if)#no shut R2(config-if)#^Z R2# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3# *Mar 1 05:26:56.019: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:26:56.019: Se1/2 PPP: Using default call direction *Mar 1 05:26:56.019: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:26:56.019: Se1/2 PPP: Session handle[3E000007] Session id[18] *Mar 1 05:26:56.019: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 05:26:56.019: Se1/2 LCP: O CONFREQ [Closed] id 18 len 14 *Mar 1 05:26:56.019: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:56.023: Se1/2 LCP: MagicNumber 0x148B88FC (0x0506148B88FC) *Mar 1 05:26:56.023: Se1/2 LCP: I CONFREQ [REQsent] id 45 len 14 *Mar 1 05:26:56.023: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:56.023: Se1/2 LCP: MagicNumber 0x148B945F (0x0506148B945F) *Mar 1 05:26:56.023: Se1/2 LCP: O CONFACK [REQsent] id 45 len 14 *Mar 1 05:26:56.023: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:56.023: Se1/2 LCP: MagicNumber 0x148B945F (0x0506148B945F) *Mar 1 05:26: R3#56.031: Se1/2 LCP: I CONFACK [ACKsent] id 18 len 14 *Mar 1 05:26:56.031: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:26:56.031: Se1/2 LCP: MagicNumber 0x148B88FC (0x0506148B88FC) *Mar 1 05:26:56.031: Se1/2 LCP: State is Open *Mar 1 05:26:56.031: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:26:56.031: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:26:56.031: Se1/2 PAP: Using password from interface PAP *Mar 1 05:26:56.031: Se1/2 PAP: O AUTH-REQ id 16 len 21 from "Two" *Mar 1 05:26:56.035: Se1/2 PAP: I AUTH-REQ id 16 len 22 from "One" *Mar 1 05:26:56.035: Se1/2 PAP: Authenticating peer One *Mar 1 05:26:56.035: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:56.035: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:26:56.039: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:26:56.039: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:26:56.043: Se1/2 PAP: O AUTH-ACK id 16 len 5 *Mar 1 05:26:56.047: Se1/2 PAP: I AUTH-ACK id 16 len 5 *Mar 1 05:26:56.047: Se1/2 PPP: Phase is UP *Mar 1 05:26:56.047: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 05:26:56.047: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:26:56.051: Se1/2 PPP: Process pending ncp packets *Mar 1 05:26:56.051: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 05:26:56.051: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:26:56.051: Se1/2 AAA/AUTHOR/IPCP: Start. Her address 180.40.7.2, we want 0.0.0.0 *Mar 1 05:26:56.051: Se1/2 CDPCP: I CONFREQ [Closed] id 1 len 4 *Mar 1 05:26:56.055: Se1/2 AAA/AUTHOR/IPCP: Reject 180.40.7.2, using 0.0.0.0 *Mar 1 05:26:56.055: Se1/2 AAA/AUTHOR/IPCP: Done. Her address 180.40.7.2, we want 0.0.0.0 *Mar 1 05:26:56.055: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 05:26:56.055: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:26:56.059: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 05:26:56.059: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:26:56.059: Se1/2 IPCP: State is Open *Mar 1 05:26:56.059: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 05:26:56.063: Se1/2 IPCP: Install route to 180.40.7.2 *Mar 1 05:26:56.063: Se1/2 IPCP: Add link info for cef entry 180.40.7.2 *Mar 1 05:26:56.067: Se1/2 CDPCP: I CONFACK [REQsent] id 1 len 4 *Mar 1 05:26:57.048: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up *Mar 1 05:26:57.072: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:26:57.096: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:26:57.121: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:26:58.054: Se1/2 CDPCP: TIMEout: State ACKrcvd *Mar 1 05:26:58.054: Se1/2 CDPCP: O CONFREQ [ACKrcvd] id 2 len 4 *Mar 1 05:26:58.058: Se1/2 CDPCP: I CONFACK [REQsent] id 2 len 4 *Mar 1 05:26:58.070: Se1/2 CDPCP: I CONFREQ [ACKrcvd] id 2 len 4 *Mar 1 05:26:58.070: Se1/2 CDPCP: O CONFACK [ACKrcvd] id 2 len 4 *Mar 1 05:26:58.070: Se1/2 CDPCP: State is Open R3# R3# R3# R3# R3# R3#u all All possible debugging has been turned off R3# RACK18AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 05:26:57.137: %SYS-5- R2#sh run | b i user username Two password 0 For-The-Show ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 speed 100 full-duplex --More--  ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp authentication pap optional ppp pap sent-username One password 0 For-The-Money ! interface Serial1/3 --More-- RACK18AS>2 [Resuming connection 2 to r2 ... ]   no ip address --More--   R2#h run       sh run i | b user username Two password 0 For-The-Show ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 208.28.1.129 255.255.255.224 speed 100 full-duplex --More--  ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial1/0.1 multipoint ip address 208.28.1.3 255.255.255.248 frame-relay map ip 208.28.1.1 203 frame-relay map ip 208.28.1.2 203 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp authentication pap optional ppp pap sent-username One password 0 For-The-Money ! interface Serial1/3 --More--   R2# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3# R3# R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#enca ppp          ^Z R3#sh *Mar 1 05:28:41.520: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | user ^ % Invalid input detected at '^' marker. R3#sh run | userbuser user username One password 0 For-The-Money ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 speed 100 full-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto --More--  ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 broadcast no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show ! interface Serial1/3 no ip address --More--   R3#confiot    t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#user R1 pass PinkCal  adl illac R3(config)#int s 1/0 R3(config-if)#fram inter R3(config-if)#fram interface-d R3(config-if)#fram interface-dlci ? <16-1007> Define a switched or locally terminated DLCI R3(config-if)#fram interface-dlci 301 ? ppp Use RFC1973 Encapsulation to support PPP over FR switched Define a switched DLCI R3(config-if)#fram interface-dlci 301 ppp ? Virtual-Template Virtual Template interface R3(config-if)#fram interface-dlci 301 ppp vi R3(config-if)#fram interface-dlci 301 ppp virtual-Template ? <1-200> Virtual-Template interface number R3(config-if)#fram interface-dlci 301 ppp virtual-Template 1 R3(config-fr-dlci)# *Mar 1 05:30:55.832: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R3(config-fr-dlci)#exit R3(config-if)#exity ^ % Invalid input detected at '^' marker. R3(config-if)#exity  R3(config)#int vir R3(config)#int virtual-temp R3(config)#int virtual-template 1 R3(config-if)#ip add un R3(config-if)#ip add unn R3(config-if)#ip add unn  R3(config-if)#ip add unnu R3(config-if)#ip add unnu? % Unrecognized command R3(config-if)#ip add unnu      R3(config-if)#ip address ? A.B.C.D IP address dhcp IP Address negotiated via DHCP negotiated IP Address negotiated over PPP pool IP Address autoconfigured from a local DHCP pool slarp Set IP address through SLARP R3(config-if)#ip address         un R3(config-if)#ip unn R3(config-if)#ip unnumbered ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config-if)#ip unnumbered ser 1/0 R3(config-if)#do sh run | b user username One password 0 For-The-Money username R1 password 0 PinkCadillac ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 speed 100 full-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto --More-- RACK18AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#username R1 password 0 PinkCadillac1 password 0 PinkCadillac 3 password 0 PinkCadillac R1(config)#int s 1/0.    0/. 0.1 R1(config-subif)#do sh run int s 1/.0 \    0/0.1 Building configuration... Current configuration : 118 bytes ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 end R1(config-subif)# frame-relay interface-dlci 103 vir R1(config-subif)# frame-relay interface-dlci 103 vir   pp vi R1(config-subif)# frame-relay interface-dlci 103 pp virtual-Template 1 R1(config-fr-dlci)# *Mar 1 05:34:43.009: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up *Mar 1 05:34:44.046: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up R1(config-fr-dlci)#exiyt ^ % Invalid input detected at '^' marker. R1(config-fr-dlci)#exiy ^ % Invalid input detected at '^' marker. R1(config-fr-dlci)#exiy  it R1(config-subif)#exityt frame-relay interface-dlci 103 pp virtual-Template 1do sh run int s 0/0.1  Building configuration... Current configuration : 118 bytes ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 end R1(config-subif)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 208.28.1.66 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 208.28.1.1 YES manual up up Ethernet0/1 17.57.100.1 YES manual up up Serial0/1 unassigned YES unset administratively down down Virtual-Access1 unassigned YES unset up up Virtual-Template1 unassigned YES unset down down R1(config-subif)#no frame-relay interface-dlci 103 R1(config-subif)# *Mar 1 05:35:30.122: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down *Mar 1 05:35:31.136: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to down R1(config-subif)#no frame-relay interface-dlci 103do sh ip int brie run int s 0/0.1exit yt frame-relay interface-dlci 103 pp virtual-Template 1 R1(config-fr-dlci)# *Mar 1 05:35:44.810: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R1(config-fr-dlci)# *Mar 1 05:35:46.000: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up R1(config-fr-dlci)# R1(config-fr-dlci)# R1(config-fr-dlci)#exit R1(config-subif)#exit frame-relay interface-dlci 103 pp virtual-Template 1no frame-relay interface-dlci 103 do sh ip int brie run int s 0/0.1 Building configuration... Current configuration : 137 bytes ! interface Serial0/0.1 point-to-point ip address 208.28.1.1 255.255.255.248 frame-relay interface-dlci 103 ppp Virtual-Template1 end R1(config-subif)#no ip address 208.28.1.1 255.255.255.248 R1(config-subif)#exiy ^ % Invalid input detected at '^' marker. R1(config-subif)#in  exit R1(config)#int vit rt R1(config)#int virtual-temp R1(config)#int virtual-template 1 R1(config-if)# ip address 208.28.1.1 255.255.255.248 R1(config-if)#ping 208.28.1.2 ^ % Invalid input detected at '^' marker. R1(config-if)#ping 208.28.1.2dping 208.28.1.2oping 208.28.1.2 ping 208.28.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/71/92 ms R1(config-if)#shut % Shutdown not allowed on virtual template interface. R1(config-if)#int s 1/  0/0 R1(config-if)#shut R1(config-if)#do deb p *Mar 1 05:37:17.963: %LINK-5-CHANGED: Interface Serial0/0, changed state to administratively down R1(config-if)#do deb ppp *Mar 1 05:37:17.967: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down R1(config-if)#do deb ppp authen *Mar 1 05:37:18.964: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down *Mar 1 05:37:19.000: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to down R1(config-if)#do deb ppp authen PPP authentication debugging is on R1(config-if)#int vir R1(config-if)#int vir       exit R1(config)#int vir R1(config)#int virtual- -temp 1 R1(config-if)#ppp authen chap R1(config-if)# RACK18AS>3 [Resuming connection 3 to r3 ... ] *Mar  speed auto --More--   R3(config-if)#nt    do sh run | b userip unnumbered ser 1/0nt virtual-template 1p unnumbered ser 1/0 do sh run | b user  ppp authen chp[  ap R3(config-if)#^Z R3# *Mar 1 05:36:38.217: %SYS-5-CONFIG_I: Configured from console by console R3# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)#int s 0/0 R1(config-if)#no shut R1(config-if)#^Z R1# *Mar 1 05:38:05.388: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up *Mar 1 05:38:05.388: Vi1 PPP: Using default call direction *Mar 1 05:38:05.388: Vi1 PPP: Treating connection as a dedicated line *Mar 1 05:38:05.388: Vi1 PPP: Session handle[81000008] Session id[3] *Mar 1 05:38:05.388: Vi1 PPP: Authorization required R1# *Mar 1 05:38:05.949: %SYS-5-CONFIG_I: Configured from console by console R1# *Mar 1 05:38:07.380: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up *Mar 1 05:38:07.400: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down *Mar 1 05:38:08.381: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up R1# R1# R1# R1# R1# *Mar 1 05:38:27.396: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R1# *Mar 1 05:38:27.400: Vi1 PPP: Using default call direction *Mar 1 05:38:27.400: Vi1 PPP: Treating connection as a dedicated line *Mar 1 05:38:27.400: Vi1 PPP: Session handle[4C000009] Session id[4] *Mar 1 05:38:27.400: Vi1 PPP: Authorization required R1# *Mar 1 05:38:29.167: Vi1 CHAP: O CHALLENGE id 1 len 23 from "R1" *Mar 1 05:38:29.187: Vi1 CHAP: I CHALLENGE id 1 len 23 from "R3" *Mar 1 05:38:29.191: Vi1 CHAP: Using hostname from unknown source *Mar 1 05:38:29.191: Vi1 CHAP: Using password from AAA *Mar 1 05:38:29.191: Vi1 CHAP: O RESPONSE id 1 len 23 from "R1" *Mar 1 05:38:29.195: Vi1 CHAP: I RESPONSE id 1 len 23 from "R3" *Mar 1 05:38:29.195: Vi1 PPP: Sent CHAP LOGIN Request *Mar 1 05:38:29.199: Vi1 PPP: Received LOGIN Response PASS *Mar 1 05:38:29.199: Vi1 PPP: Sent LCP AUTHOR Request *Mar 1 05:38:29.203: Vi1 PPP: Sent IPCP AUTHOR Request *Mar 1 05:38:29.203: Vi1 LCP: Received AAA AUTHOR Response PASS R1# *Mar 1 05:38:29.203: Vi1 IPCP: Received AAA AUTHOR Response PASS *Mar 1 05:38:29.207: Vi1 CHAP: O SUCCESS id 1 len 4 *Mar 1 05:38:29.211: Vi1 CHAP: I SUCCESS id 1 len 4 *Mar 1 05:38:29.219: Vi1 PPP: Sent IPCP AUTHOR Request R1# *Mar 1 05:38:30.213: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up R1#sh run | b user username R3 password 0 PinkCadillac ! ! ! ! interface Ethernet0/0 ip address 208.28.1.66 255.255.255.240 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial0/0.1 point-to-point frame-relay interface-dlci 103 ppp Virtual-Template1 ! interface Ethernet0/1 ip address 17.57.100.1 255.255.255.0 half-duplex ! interface Serial0/1 no ip address --More--   shutdown ! interface Virtual-Template1 ip address 208.28.1.1 255.255.255.248 ppp authentication chap ! ip http server ip classless ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! --More--   R1# RACK18AS>3 [Resuming connection 3 to r3 ... ] * R3#sh run | b user username One password 0 For-The-Money username R1 password 0 PinkCadillac ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 17.80.1.1 255.255.255.0 speed 100 full-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto --More--   speed auto ! interface Serial1/0 ip address 208.28.1.2 255.255.255.248 encapsulation frame-relay ip split-horizon no fair-queue frame-relay map ip 208.28.1.1 301 broadcast frame-relay map ip 208.28.1.2 302 frame-relay map ip 208.28.1.3 302 broadcast frame-relay interface-dlci 301 ppp Virtual-Template1 no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show ! --More--  interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! interface Virtual-Template1 ip unnumbered Serial1/0 ppp authentication chap --More--  ! ip classless ! ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 ! ! end --More--   R3#ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1#ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/115/117 ms R1# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int s 1/0 R3(config-if)#no frame-relay map ip 208.28.1.1 301 broadcast R3(config-if)#^Z R3#p *Mar 1 05:40:33.038: %SYS-5-CONFIG_I: Configured from console by console R3#ping 208.28.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/65/80 ms R3# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1#ping 208.28.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.28.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/117/124 ms R1# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.1/32 is directly connected, Virtual-Access1 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/16 is variably subnetted, 2 subnets, 2 masks C 180.40.7.2/32 is directly connected, Serial1/2 C 180.40.7.0/27 is directly connected, Serial1/2 R3#  confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#pp ? accm Set initial Async Control Character Map accounting Set PPP network accounting method acfc Options for HDLC Address & Control Field Compression authentication Set PPP link authentication method authorization Set PPP network authorization method bridge Enable PPP bridge translation caller Caller option when no CLID is available chap Set CHAP authentication parameters direction Override default PPP direction dnis Authentication via DNIS before LCP eap Set EAP authentication parameters encrypt Enable PPP encryption ipcp Set IPCP negotiation options iphc Set IPCP Header Compression control options lcp PPP LCP configuration link Set miscellaneous link parameters loopback PPP loopback options max-bad-auth Allow multiple authentication failures max-configure Number of conf-reqs sent before assuming peer is unable to respond max-failure Number of conf-naks sent before assuming configuration is not converging --More--   max-terminate Number of term-reqs sent before assuming peer is unable to respond ms-chap Set MS-CHAP authentication parameters ms-chap-v2 Set MS-CHAP-V2 authentication parameters multilink Make interface multilink capable pap Set PAP authentication parameters pfc Options for Protocol Field Compression quality Set parameters related to Link Quality Monitoring (LQM) reliable-link Use LAPB with PPP to provide a reliable link timeout Set PPP timeout parameters R3(config-if)#pp    shut R3(config-if)#ppp rel R3(config-if)#ppp reliable-link *Mar 1 05:43:05.023: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 05:43:06.025: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#ppp reliable-link R3(config-if)# RACK18AS>2 [Resuming connection 2 to r2 ... ] *M R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#ppp rel R2(config-if)#ppp reliable-link R2(config-if)#^Z R2# *Ma RACK18AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#no shu      de  do deb ne NetBIOS name cache tracing debugging is on R3(config-if)#do deb nepnepnepne ne PPP protocol negotiation debugging is on R3(config-if)#no shut R3(config-if)# *Mar 1 05:43:47.385: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:43:47.409: Se1/2 PPP: Outbound cdp packet dropped *Mar 1 05:43:47.433: Se1/2 PPP: Outbound cdp packet dropped R3(config-if)#^Z R3# *Mar 1 05:43:49.087: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 05:43:49.360: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 05:43:49.360: Se1/2 PPP: Using default call direction *Mar 1 05:43:49.360: Se1/2 PPP: Treating connection as a dedicated line *Mar 1 05:43:49.360: Se1/2 PPP: Session handle[7E00000E] Session id[22] *Mar 1 05:43:49.360: Se1/2 PPP: Phase is ESTABLISHING, Active Open *Mar 1 05:43:49.360: Se1/2 LCP: O CONFREQ [Closed] id 19 len 18 *Mar 1 05:43:49.360: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:43:49.364: Se1/2 LCP: MagicNumber 0x149AFF61 (0x0506149AFF61) *Mar 1 05:43:49.364: Se1/2 LCP: ReliableLink window 7 addr 0 (0x0B040700) *Mar 1 05:43:49.368: Se1/2 LCP: I CONFREQ [REQsent] id 46 len 18 *Mar 1 05:43:49.368: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:43:49.368: Se1/2 LCP: MagicNumber 0x149B0AC1 (0x0506149B0AC1) *Mar 1 05:43:49.368: Se1/2 LCP: ReliableLink window 7 addr 0 (0x R3#0B040700) *Mar 1 05:43:49.372: Se1/2 LCP: O CONFNAK [REQsent] id 46 len 8 *Mar 1 05:43:49.372: Se1/2 LCP: ReliableLink window 7 addr 3 (0x0B040703) *Mar 1 05:43:49.372: Se1/2 LCP: I CONFNAK [REQsent] id 19 len 8 *Mar 1 05:43:49.372: Se1/2 LCP: ReliableLink window 7 addr 1 (0x0B040701) *Mar 1 05:43:49.372: Se1/2 LCP: O CONFREQ [REQsent] id 20 len 18 *Mar 1 05:43:49.372: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:43:49.376: Se1/2 LCP: MagicNumber 0x149AFF61 (0x0506149AFF61) *Mar 1 05:43:49.376: Se1/2 LCP: ReliableLink window 7 addr 1 (0x0B040701) *Mar 1 05:43:49.380: Se1/2 LCP: I CONFREQ [REQsent] id 47 len 18 *Mar 1 05:43:49.380: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:43:49.380: Se1/2 LCP: MagicNumber 0x149B0AC1 (0x0506149B0AC1) *Mar 1 05:43:49.380: Se1/2 LCP: ReliableLink window 7 addr 3 (0x0B040703) *Mar 1 05:43:49.380: Se1/2 LCP: O CONFACK [REQsent] id 47 len 18 *Mar 1 05:43:49.380: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:43:49.384: Se1/2 LCP: MagicNumber 0x149B0AC1 (0x0506149B0AC1) *Mar 1 05:43:49.384: Se1/2 LCP: ReliableLink window 7 addr 3 (0x0B040703) *Mar 1 05:43:49.384: Se1/2 LCP: I CONFACK [ACKsent] id 20 len 18 *Mar 1 05:43:49.384: Se1/2 LCP: AuthProto PAP (0x0304C023) *Mar 1 05:43:49.384: Se1/2 LCP: MagicNumber 0x149AFF61 (0x0506149AFF61) *Mar 1 05:43:49.384: Se1/2 LCP: ReliableLink window 7 addr 1 (0x0B040701) *Mar 1 05:43:49.384: Se1/2 LCP: State is Open *Mar 1 05:43:49.388: Se1/2 PPP: Phase is AUTHENTICATING, by both *Mar 1 05:43:49.388: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:43:49.388: Se1/2 PAP: Using password from interface PAP *Mar 1 05:43:49.388: Se1/2 PAP: O AUTH-REQ id 17 len 21 from "Two" *Mar 1 05:43:49.396: Se1/2 PAP: I AUTH-REQ id 17 len 22 from "One" *Mar 1 05:43:49.396: Se1/2 PAP: Authenticating peer One *Mar 1 05:43:49.396: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:43:49.400: Se1/2 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 1 05:43:49.400: Se1/2 PPP: Phase is FORWARDING, Attempting Forward *Mar 1 05:43:49.400: Se1/2 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 1 05:43:49.404: Se1/2 PAP: O AUTH-ACK id 17 len 5 R3# R3# *Mar 1 05:43:59.368: Se1/2 AUTH: Timeout 1 *Mar 1 05:43:59.368: Se1/2 PAP: Using hostname from interface PAP *Mar 1 05:43:59.368: Se1/2 PAP: Using password from interface PAP *Mar 1 05:43:59.368: Se1/2 PAP: O AUTH-REQ id 18 len 21 from "Two" *Mar 1 05:43:59.380: Se1/2 PAP: I AUTH-ACK id 18 len 5 *Mar 1 05:43:59.380: Se1/2 PPP: Phase is UP *Mar 1 05:43:59.384: Se1/2 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 1 05:43:59.384: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:43:59.384: Se1/2 PPP: Process pending ncp packets *Mar 1 05:43:59.384: Se1/2 CDPCP: I CONFREQ [Closed] id 1 len 4 *Mar 1 05:43:59.384: Se1/2 IPCP: I CONFREQ [REQsent] id 1 len 10 *Mar 1 05:43:59.388: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:43:59.388: Se1/2 AAA/AUTHOR/IPCP: Start. Her address 180.40.7.2, we want 0.0.0.0 *Mar 1 05:43:59.388: Se1/2 AAA/AUTHOR/IPCP: Reject 180.40.7.2, using 0.0.0.0 *Mar 1 05:43:59.388: Se1/2 AAA/AUTHOR/IPCP: Done. Her addres R3#s 180.40.7.2, we want 0.0.0.0 *Mar 1 05:43:59.392: Se1/2 IPCP: O CONFACK [REQsent] id 1 len 10 *Mar 1 05:43:59.392: Se1/2 IPCP: Address 180.40.7.2 (0x0306B4280702) *Mar 1 05:43:59.392: Se1/2 IPCP: I CONFACK [ACKsent] id 1 len 10 *Mar 1 05:43:59.392: Se1/2 IPCP: Address 180.40.7.3 (0x0306B4280703) *Mar 1 05:43:59.392: Se1/2 IPCP: State is Open *Mar 1 05:43:59.396: Se1/2 CDPCP: O CONFREQ [Closed] id 1 len 4 *Mar 1 05:43:59.396: Se1/2 IPCP: Install route to 180.40.7.2 *Mar 1 05:43:59.400: Se1/2 IPCP: Add link info for cef entry 180.40.7.2 *Mar 1 05:43:59.400: Se1/2 CDPCP: I CONFACK [REQsent] id 1 len 4 R3# *Mar 1 05:44:00.382: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up *Mar 1 05:44:01.384: Se1/2 CDPCP: TIMEout: State ACKrcvd *Mar 1 05:44:01.384: Se1/2 CDPCP: O CONFREQ [ACKrcvd] id 2 len 4 R3# *Mar 1 05:44:01.388: Se1/2 CDPCP: I CONFACK [REQsent] id 2 len 4 *Mar 1 05:44:01.396: Se1/2 CDPCP: I CONFREQ [ACKrcvd] id 2 len 4 *Mar 1 05:44:01.396: Se1/2 CDPCP: O CONFACK [ACKrcvd] id 2 len 4 *Mar 1 05:44:01.396: Se1/2 CDPCP: State is Open R3# R3# R3# R3#u all All possible debugging has been turned off R3#sh int s 1/2 Serial1/2 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is 180.40.7.3/27 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, LCP Open Open: CDPCP, IPCP LAPB DCE, state CONNECT, modulo 8, k 7, N1 12048, N2 3 T1 3000, T2 0, interface outage (partial T3) 0, T4 0, PPP over LAPB VS 4, VR 5, tx NR 5, Remote VR 4, Retransmissions 0 Queues: U/S frames 0, I frames 0, unack. 0, reTx 0 IFRAMEs 20/21 RNRs 0/0 REJs 0/0 SABM/Es 1/1 FRMRs 0/0 DISCs 0/0, loopback not set Keepalive set (10 sec) Last input 00:00:07, output 00:00:07, output hang never Last clearing of "show interface" counters 00:31:32 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec --More--   R3# RACK18AS>2 [Resuming connection 2 to r2 ... ] 1 05:43:19.146: % R2#sh run int s 1/2 Building configuration... Current configuration : 207 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp clock rate 64000 ppp reliable-link ppp authentication pap optional ppp pap sent-username One password 0 For-The-Money end R2# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3# R3#sh run | b     int s 1/2 Building configuration... Current configuration : 188 bytes ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 encapsulation ppp ppp reliable-link ppp authentication pap optional ppp pap sent-username Two password 0 For-The-Show end R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] * R4#sh run int s at,1  ,  1/0 Building configuration... Current configuration : 72 bytes ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive end R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int atm 1/0 R4(config-if)#ip add 10  192.10.32.18 255.255.255.0 R4(config-if)#pvc 0/72 R4(config-if-atm-vc)#pro R4(config-if-atm-vc)#protocol 192.10.32.254 R4(config-if-atm-vc)#exit R4(config-if)#no shut R4(config-if)# *Mar 1 05:50:56.882: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up *Mar 1 05:50:57.882: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up R4(config-if)#do ping 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R4(config-if)#exit R4(config)#ip nat ? Stateful Stateful NAT configuration commands inside Inside address translation log NAT Logging outside Outside address translation pool Define pool of addresses service Special translation for application using non-standard port translation NAT translation entry configuration R4(config)#ip nat in ? destination Destination address translation source Source address translation R4(config)#ip nat in sou ? list Specify access list describing local addresses route-map Specify route-map static Specify static local->global mapping R4(config)#ip nat in sou               access-list 1 per any R4(config)# R4(config)# R4(config)# R4(config)#ip nat in sou li 1 ? interface Specify interface for global address pool Name pool of global addresses R4(config)#ip nat in sou li 1 int atm 1/0 ? overload Overload an address translation vrf Specify vrf R4(config)#ip nat in sou li 1 int atm 1/0 ov R4(config)#ip nat in sou li 1 int atm 1/0 overload ? R4(config)#ip nat in sou li 1 int atm 1/0 overload R4(config)#int atm 1/0 R4(config-if)#ip nat i out R4(config-if)#int fa 0/0 R4(config-if)#ip nat in R4(config-if)#ex  ^Z R4# *Mar 1 05:52:32.222: %SYS-5-CONFIG_I: Configured from console by console R4#ping    deb ip nat IP NAT debugging is on R4#ping 192.10.32.254 sou fa 0/0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: Packet sent with a source address of 17.80.1.2 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms R4# *Mar 1 05:52:55.978: NAT: s=17.80.1.2->192.10.32.18, d=192.10.32.254 [5] *Mar 1 05:52:55.982: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.2 [5] *Mar 1 05:52:55.986: NAT: s=17.80.1.2->192.10.32.18, d=192.10.32.254 [6] *Mar 1 05:52:55.986: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.2 [6] *Mar 1 05:52:55.990: NAT: s=17.80.1.2->192.10.32.18, d=192.10.32.254 [7] *Mar 1 05:52:55.994: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.2 [7] *Mar 1 05:52:55.994: NAT: s=17.80.1.2->192.10.32.18, d=192.10.32.254 [8] *Mar 1 05:52:55.998: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.2 [8] *Mar 1 05:52:56.002: NAT: s=17.80.1.2->192.10.32.18, d=192.10.32.254 [9] R4# *Mar 1 05:52:56.006: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.2 [9] R4# R4# R4# R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.80.1.0 is directly connected, FastEthernet0/0 208.28.1.0/24 is variably subnetted, 2 subnets, 2 masks C 208.28.1.1/32 is directly connected, Virtual-Access1 C 208.28.1.0/29 is directly connected, Serial1/0 180.40.0.0/16 is variably subnetted, 2 subnets, 2 masks C 180.40.7.2/32 is directly connected, Serial1/2 C 180.40.7.0/27 is directly connected, Serial1/2 R3#confit    t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip route 0/ .0.0.0 0.0.0.0 fa 0/0 R3(config)#^Z R3#ping 192 *Mar 1 05:50:55.759: %SYS-5-CONFIG_I: Configured from console by console R3#ping 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 4/4/4 ms R3# R3# R3# R3# R3#ping 192.10.32.254192.10.32.254 192.10.32.254 192.10.32.254 192.10.32.254 192.10.32.254  Trying 192.10.32.254 ... Open CR1>q [Connection to 192.10.32.254 closed by foreign host] R3# R3# RACK18AS>c 4 [Resuming connection 4 to r4 ... ] *Mar R4#sh ip nat tra Pro Inside global Inside local Outside local Outside global tcp 192.10.32.18:24448 17.80.1.1:24448 192.10.32.254:23 192.10.32.254:23 icmp 192.10.32.18:1 17.80.1.2:1 192.10.32.254:1 192.10.32.254:1 icmp 192.10.32.18:9 17.80.1.1:9 192.10.32.254:9 192.10.32.254:9 tcp 192.10.32.18:1 192.10.32.18:179 192.10.32.254:60764 192.10.32.254:60764 R4# *Mar 1 05:53:56.006: NAT: expiring 192.10.32.18 (17.80.1.2) icmp 1 (1) R4# *Mar 1 05:54:00.514: NAT: TCP s=179->1, d=60764 R4#u all All possible debugging has been turned off R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)# R4(config)#ip nat out ? source Source address translation R4(config)#ip nat out sou ? list Specify access list describing global addresses route-map Specify route-map static Specify static global->local mapping R4(config)#ip nat out sou st R4(config)#ip nat out sou static ? A.B.C.D Outside global IP address network Subnet translation tcp Transmission Control Protocol udp User Datagram Protocol R4(config)#ip nat out sou static 192.10.32.254 ? A.B.C.D Outside local IP address R4(config)#ip nat out sou static 192.10.32.254 17.80.1.3 R4(config)#^Z R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#ping 17.80.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.3, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms R3#ping 17.80.1.3g 17.80.1.3 17.80.1.3 17.80.1.3 17.80.1.3 17.80.1.3  Trying 17.80.1.3 ... % Connection refused by remote host R3#17.80.1.3ping 17.80.1.3192.10.32.254  Trying 192.10.32.254 ... Open CR1>q [Connection to 192.10.32.254 closed by foreign host] R3#192.10.32.2547.80.1.3  Trying 17.80.1.3 ... % Connection refused by remote host R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#deb ip nat IP NAT debugging is on R4# R4# R4# R4# R4#confi g t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#logg buff R4(config)#^Z R4# R4# R4# R4# R4# *Mar 1 05:57:00.750: %SYS-5-CONFIG_I: Configured from console by console R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 70 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 1 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 24 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 05:57:00.750: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4# R4# R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#17.80.1.392.10.32.2547.80.1.3 ping 17.80.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 70 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 1 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 24 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 05:57:00.750: %SYS-5-CONFIG_I: Configured from console by console R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#ping 17.80.1.317.80.1.3 92.10.32.254p192.10.32.254 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] *Mar8, d=192.10.32.254 [61] R4# R4# *Mar 1 05:57:26.898: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [61] R4# R4# R4# R4#u all All possible debugging has been turned off R4#deb ip icmp ICMP packet debugging is on R4# R4# R4# R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] p 192.10.32.254 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.10.32.254, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/8 ms R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 80 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 11 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 24 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 05:57:00.750: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 05:57:26.878: NAT: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [57] *Mar 1 05:57:26.882: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [57] *Mar 1 05:57:26.882: NAT*: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [58] *Mar 1 05:57:26.886: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [58] *Mar 1 05:57:26.890: NAT*: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [59] *Mar 1 05:57:26.890: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [59] *Mar 1 05:57:26.894: NAT*: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [60] *Mar 1 05:57:26.894: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [60] *Mar 1 05:57:26.898: NAT*: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [61] *Mar 1 05:57:26.898: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [61] R4#     R4# R4# R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#p 192.10.32.254ing 17.80.1.3 17.80.1.3 ping 17.80.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.80.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] *M 1 05:58:02.510: ICMP: echo reply sent, src 17.80.1.3, dst 17.80.1.1 *Mar 1 05:58:02.514: ICMP: echo reply sent, src 17.80.1.3, dst 17.80.1.1 R4# R4# R4# R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 85 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 16 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 24 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 05:57:00.750: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 05:57:26.878: NAT: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [57] *Mar 1 05:57:26.882: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [57] *Mar 1 05:57:26.882: NAT*: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [58] *Mar 1 05:57:26.886: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [58] *Mar 1 05:57:26.890: NAT*: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [59] *Mar 1 05:57:26.890: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [59] *Mar 1 05:57:26.894: NAT*: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [60] *Mar 1 05:57:26.894: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [60] *Mar 1 05:57:26.898: NAT*: s=17.80.1.1->192.10.32.18, d=192.10.32.254 [61] *Mar 1 05:57:26.898: NAT*: s=192.10.32.254, d=192.10.32.18->17.80.1.1 [61] *Mar 1 05:58:02.490: ICMP: echo reply sent, src 17.80.1.3, dst 17.80.1.1 *Mar 1 05:58:02.498: ICMP: echo reply sent, src 17.80.1.3, dst 17.80.1.1 *Mar 1 05:58:02.502: ICMP: echo reply sent, src 17.80.1.3, dst 17.80.1.1 *Mar 1 05:58:02.510: ICMP: echo reply sent, src 17.80.1.3, dst 17.80.1.1 *Mar 1 05:58:02.514: ICMP: echo reply sent, src 17.80.1.3, dst 17.80.1.1 R4# R4# R4# R4#sh ip nat ta ra Pro Inside global Inside local Outside local Outside global --- --- --- 17.80.1.3 192.10.32.254 icmp 192.10.32.18:12 17.80.1.1:12 192.10.32.254:12 192.10.32.254:12 icmp 192.10.32.18:13 17.80.1.1:13 192.10.32.254:13 192.10.32.254:13 tcp 192.10.32.18:4 192.10.32.18:179 192.10.32.254:60764 192.10.32.254:60764 R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#no ip cef R4(config)# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#ping 17.80.1.3 192.10.32.254ing 17.80.1.3 17.80.1.3  Trying 17.80.1.3 ... % Connection refused by remote host R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] R4(config)#i  p cef R4(config)#^Z R4# *Mar 1 06:00:06.750: %SYS-5-CONFIG_I: Configured from console by console R4#sh run | b atm   m no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 ! ! ip nat inside source list 1 interface ATM1/0 overload ip nat outside source static 192.10.32.254 17.80.1.3 ip http server no ip http secure-server ip classless ! ! access-list 1 permit any ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 --More--   R4#sh run | b atm   1/0 interface ATM1/0 ip address 192.10.32.18 255.255.255.0 ip nat outside no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 ! ! ip nat inside source list 1 interface ATM1/0 overload ip nat outside source static 192.10.32.254 17.80.1.3 ip http server no ip http secure-server ip classless ! ! access-list 1 permit any ! ! ! ! ! ! line con 0 --More--   R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip cefno ip ceflogg buffip nat out sou static 192.10.32.254 17.80.1.3   250 % 192.10.32.254 already mapped (17.80.1.3 -> 192.10.32.254) R4(config)#ip nat out sou static 192.10.32.254 17.80.1.250cef no ip ceflogg buffip nat out sou static 192.10.32.254 17.80.1.3 ex R4(config)#ip nat out sou static 192.10.32.254 17.80.1.3 extendable R4(config)#ip nat out sou static 192.10.32.254 17.80.1.3 extendable 250  x ex R4(config)#ip nat out sou static 192.10.32.254 17.80.1.250 ex3 extendable 250 ex  ex 2 ex R4(config)#ip nat out sou static 192.10.32.254 17.80.1.252 ex ex 4 ex R4(config)#^Z R4# *Mar 1 06:01:37.578: %SYS-5-CONFIG_I: Configured from console by console R4#sh run | i ip nat ip nat inside ip nat outside ip nat inside source list 1 interface ATM1/0 overload ip nat outside source static 192.10.32.254 17.80.1.3 extendable ip nat outside source static 192.10.32.254 17.80.1.250 extendable ip nat outside source static 192.10.32.254 17.80.1.252 extendable ip nat outside source static 192.10.32.254 17.80.1.254 extendable R4#