=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2005.11.08 06:28:59 =~=~=~=~=~=~=~=~=~=~=~= RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#dlsw ? allroute-netbios Use All routes Broadcast for NETBIOS Explorers allroute-sna Use All routes Broadcast for SNA Explorers bgroup-list Configure a transparent bridge group list bridge-group DLSw interconnection to transparent bridging cache-ignore-netbios-datagram Don't cache source mac/name of NetBIOS datagrams circuit-keepalives Configure DLSw+ to generate periodic circuit keepalives disable Disable DLSw without altering the configuration explorerQ-depth Configure depth of DLSw control queues fast-hpr-support Enable fast-switched HPR transport group-cache Border Peer Caching Options history-log Configure DLSw Circuit-History Log Capability icannotreach Configure a resource not locally reachable by this router icanreach Configure resources locally reachable by this router llc2 Dlsw llc2 options load-balance Configure load balancing local-peer Configure local peer mac-addr Configure a static MAC address - location or --More--   path max-multiple-rifs Configure maximum multiple rifs per interface multicast Configure DLSw Multicast Capability netbios-cache-length Configure NetBIOS name length netbios-keepalive-filter Filter NetBIOS session alive packets netbios-name Configure a static NetBios name - location or path peer-log-changes print logging message in router log ONLY for error events peer-on-demand-defaults Change peer-on-demand defaults port-list Configure a port list prom-peer-defaults Change prom-peer-defaults redundant-rings Configure redundant ring-list remote-peer Configure a remote peer ring-list Configure a ring list rsvp Configure reservations using RSVP timer Configure DLSw timers tos Change IP Type Of Service precedence bits touch-timer Configure DLSw touch timers transparent Configure transparent media options udp-disable Disable DLSw UDP unicast feature R1(config)#dlsw local-peer ? biu-segment XID3 max receivable i-field spoofing and BIU segmenting border Capable of operating as a border peer cluster Set cluster id for this router cost Set peer cost advertised to remote peers group Set the peer group number for this router init-pacing-window Initial Pacing Window Size for this local peer keepalive Set the default remote peer keepalive interval lf Local peer largest frame size max-pacing-window Maximum Pacing Window Size for this local peer passive This router will not initiate remote peer connections peer-id local-peer IP address; required for TCP/FST and peer groups promiscuous Accept connections from non-configured remote peers R1(config)#dlsw local-peer peer ? A.B.C.D Local Peer IP address R1(config)#dlsw local-peer peer ? A.B.C.D Local Peer IP address R1(config)#dlsw local-peer peer                      do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 1 subnets C 17.57.100.0 is directly connected, Ethernet0/0 O 200.1.1.0/24 [110/65] via 180.40.7.65, 12:20:15, Serial0/0 180.40.0.0/16 is variably subnetted, 4 subnets, 2 masks O 180.40.7.128/27 [110/846] via 180.40.7.65, 12:20:15, Serial0/0 O 180.40.7.0/27 [110/845] via 180.40.7.65, 12:20:15, Serial0/0 O 180.40.7.65/32 [110/64] via 180.40.7.65, 12:20:15, Serial0/0 C 180.40.7.64/27 is directly connected, Serial0/0 R1(config)#dlsw lo R1(config)#dlsw loc R1(config)#dlsw local-peer 17.57.100.1 ? % Unrecognized command R1(config)#dlsw local-peer 17.57.100.1   ? % Unrecognized command R1(config)#dlsw local-peer 17.57.100.1            ? biu-segment XID3 max receivable i-field spoofing and BIU segmenting border Capable of operating as a border peer cluster Set cluster id for this router cost Set peer cost advertised to remote peers group Set the peer group number for this router init-pacing-window Initial Pacing Window Size for this local peer keepalive Set the default remote peer keepalive interval lf Local peer largest frame size max-pacing-window Maximum Pacing Window Size for this local peer passive This router will not initiate remote peer connections peer-id local-peer IP address; required for TCP/FST and peer groups promiscuous Accept connections from non-configured remote peers R1(config)#dlsw local-peer pee R1(config)#dlsw local-peer peer-id 17.57.100.1 ? biu-segment XID3 max receivable i-field spoofing and BIU segmenting border Capable of operating as a border peer cluster Set cluster id for this router cost Set peer cost advertised to remote peers group Set the peer group number for this router init-pacing-window Initial Pacing Window Size for this local peer keepalive Set the default remote peer keepalive interval lf Local peer largest frame size max-pacing-window Maximum Pacing Window Size for this local peer passive This router will not initiate remote peer connections peer-id local-peer IP address; required for TCP/FST and peer groups promiscuous Accept connections from non-configured remote peers R1(config)#dlsw local-peer peer-id 17.57.100.1 R1(config)#de lsw R1(config)#dlsw remo R1(config)#dlsw remote-peer ? <0-4095> Remote peer ring group list R1(config)#dlsw remote-peer 1 ? frame-relay Use Frame Relay for remote peer transport fst Use fast sequence transport (FST) for remote peer transport interface Use a direct interface for remote peer transport tcp Use TCP for remote peer transport R1(config)#dlsw remote-peer 1 fram R1(config)#dlsw remote-peer 1 frame-relay ? interface Serial interface over which to run TR traffic R1(config)#dlsw remote-peer 1 frame-relay in R1(config)#dlsw remote-peer 1 frame-relay interface ? Serial Serial R1(config)#dlsw remote-peer 1 frame-relay interface ser ? <0-1> Serial interface number R1(config)#dlsw remote-peer 1 frame-relay interface ser 0/0 ? <16-1007> Frame-Relay DLCI Number R1(config)#dlsw remote-peer 1 frame-relay interface ser 0/0 102 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets pass-thru Remote peer is capable of locally acknowledging DLC sessions passive Local peer will not initiate this remote peer connection rsvp Configure reservations using RSVP R1(config)#dlsw remote-peer 1 frame-relay interface ser 0/0 102 pas R1(config)#dlsw remote-peer 1 frame-relay interface ser 0/0 102 pass R1(config)#dlsw remote-peer 1 frame-relay interface ser 0/0 102 pass- R1(config)#dlsw remote-peer 1 frame-relay interface ser 0/0 102 pass-thru ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets pass-thru Remote peer is capable of locally acknowledging DLC sessions passive Local peer will not initiate this remote peer connection rsvp Configure reservations using RSVP R1(config)#dlsw remote-peer 1 frame-relay interface ser 0/0 102 pass-thru %port-list 1 does not exist. R1(config)# R1(config)# R1(config)# R1(config)# R1(config)# R1(config)#dlsw remote-peer 1 frame-relay interface ser 0/0 102 pass-thru  frame-relay interface ser 0/0 102 pass-thru 0 frame-relay interface ser 0/0 102 pass-thru  R1(config)#int s 0/0 R1(config-if)#fram map R1(config-if)#fram map ? bridge Bridging bstun Block Serial Tunnel clns ISO CLNS decnet DECnet dlsw Data Link Switching ip IP ipv6 IPV6 ipx Novell IPX llc2 llc2 pppoe PPP over Ethernet qllc qllc protocol rsrb Remote Source-Route Bridging stun Serial Tunnel R1(config-if)#fram map dlsw ? <16-1007> DLCI R1(config-if)#fram map dlsw 201     102 ? broadcast Broadcasts should be forwarded to this address cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation payload-compression Use payload compression R1(config-if)#fram map dlsw 102 br R1(config-if)#fram map dlsw 102 broadcast ? broadcast Broadcasts should be forwarded to this address cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation payload-compression Use payload compression R1(config-if)#fram map dlsw 102 broadcast R1(config-if)# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#dlsw lo R2(config)#dlsw lovc  c R2(config)#dlsw local-peer p R2(config)#dlsw local-peer pe R2(config)#dlsw local-peer peer-id 200.1.1.2 R2(config)#dlsw remote 0 ? frame-relay Use Frame Relay for remote peer transport fst Use fast sequence transport (FST) for remote peer transport interface Use a direct interface for remote peer transport tcp Use TCP for remote peer transport R2(config)#dlsw remote 0 fram int s 1/0 201 R2(config)#int s 1/0 R2(config-if)#fram map dlsw 201 bro R2(config-if)#fram map dlsw 201 broadcast R2(config-if)#^Z R2# RACK14AS>1 [Resuming connection 1 to r1 ... ] ^Z R1#sh *Mar 1 12:34:05.205: %SYS-5-CONFIG_I: Configured from console by console R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se0/0 102 WAIT_CAP 0 1 conf 0 - - - Total number of connected peers: 0 Total number of connections: 0 R1# R1# R1# R1# R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se0/0 102 DISCONN 0 0 conf 0 - - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se0/0 102 DISCONN 0 0 conf 0 - - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se0/0 102 DISCONN 0 0 conf 0 - - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se0/0 102 DISCONN 0 0 conf 0 - - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se0/0 102 DISCONN 0 0 conf 0 - - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se0/0 102 DISCONN 0 0 conf 0 - - - Total number of connected peers: 0 Total number of connections: 0 R1#debv dls      dlsw DLSw reachability debugging is on at event level for all protocol traffic DLSw peer debugging is on DLSw local circuit debugging is on DLSw core message debugging is on DLSw core state debugging is on DLSw core flow control debugging is on DLSw core xid debugging is on R1# R1# R1# R1#deb dlswsh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se0/0 102 DISCONN 0 0 conf 0 - - - Total number of connected peers: 0 Total number of connections: 0 R1#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 25 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: disabled, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 30 message lines logged R1# *Mar 1 12:34:38.407: DLSw: START-FSTPFSM (peer on interface Serial0/0): event:ADMIN-OPEN CONNECTION state:DISCONN *Mar 1 12:34:38.407: DLSw: dfstp_action_a() attempting to connect peer on interface Serial0/0 *Mar 1 12:34:38.407: DLSw: Connection opened for peer on interface Serial0/0 *Mar 1 12:34:38.411: DLSw: CapExId Msg sent to peer on interface Serial0/0 *Mar 1 12:34:38.411: DLSw: END-FSTPFSM (peer on interface Serial0/0): state:DISCONN->WAIT_CAP R1# *Mar 1 12:34:44.441: DLSw: START-FSTPFSM (peer on interface Serial0/0): event:TIMER-TIMER EXPIRED state:WAIT_CAP *Mar 1 12:34:44.441: DLSw: dfstp_action_d() close connection for peer on interface Serial0/0 *Mar 1 12:34:44.441: DLSw: DIRECT aborting connection for peer on interface Serial0/0 *Mar 1 12:34:44.441: DLSw: END-FSTPFSM (peer on interface Serial0/0): state:WAIT_CAP->DISCONN R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0 R1(config-if)#do sh run | *Mar 1 12:35:14.555: DLSw: START-FSTPFSM (peer on interface Serial0/0): event:ADMIN-OPEN CONNECTION state:DISCONN *Mar 1 12:35:14.555: DLSw: dfstp_action_a() attempting to connect peer on interface Serial0/0 *Mar 1 12:35:14.555: DLSw: Connection opened for peer on interface Serial0/0 *Mar 1 12:35:14.555: DLSw: CapExId Msg sent to peer on interface Serial0/0 *Mar 1 12:35:14.555: DLSw: END-FSTPFSM (peer on interface Serial0/0): state:DISCONN->WAIT_CAP R1(config-if)#do sh run | i *Mar 1 12:35:20.608: DLSw: START-FSTPFSM (peer on interface Serial0/0): event:TIMER-TIMER EXPIRED state:WAIT_CAP *Mar 1 12:35:20.608: DLSw: dfstp_action_d() close connection for peer on interface Serial0/0 *Mar 1 12:35:20.608: DLSw: DIRECT aborting connection for peer on interface Serial0/0 *Mar 1 12:35:20.608: DLSw: END-FSTPFSM (peer on interface Serial0/0): state:WAIT_CAP->DISCONN R1(config-if)#do sh run | i dlsw dlsw local-peer peer-id 17.57.100.1 dlsw remote-peer 0 frame-relay interface Serial0/0 102 pass-thru frame-relay map dlsw 102 broadcast R1(config-if)#do u all All possible debugging has been turned off R1(config-if)# RACK14AS>2 [Resuming connection 2 to r2 ... ] * R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#fram map dlsw 201 broadcast int s 1/0 dlsw remote 0 fram int s 1/0 201 pass R2(config)#dlsw remote 0 fram int s 1/0 201 pass % Ambiguous command: "dlsw remote 0 fram int s 1/0 201 pass" R2(config)#dlsw remote 0 fram int s 1/0 201 pass-t R2(config)#dlsw remote 0 fram int s 1/0 201 pass-thru %error: peers with same ipaddr & different transport types R2(config)#dlsw remote 0 fram int s 1/0 201 pass-thru  fram map dlsw 201 broadcast int s 1/0 dlsw remote 0 fram int s 1/0 201ndlsw remote 0 fram int s 1/0 201odlsw remote 0 fram int s 1/0 201 dlsw remote 0 fram int s 1/0 201 R2(config)#no dlsw remote 0 fram int s 1/0 201dlsw remote 0 fram int s 1/0 201 pass-thru R2(config)#^Z R2# *Mar 1 12:35:05.784: %SYS-5-CONFIG_I: Configured from console by console R2#do  deb dlsw DLSw reachability debugging is on at event level for all protocol traffic DLSw peer debugging is on DLSw local circuit debugging is on DLSw core message debugging is on DLSw core state debugging is on DLSw core flow control debugging is on DLSw core xid debugging is on R2#sh dl *Mar 1 12:35:16.718: DLSw: START-FSTPFSM (peer on interface Serial1/0): event:SSP-CAP MSG RCVD state:DISCONN *Mar 1 12:35:16.718: DLSw: dfstp_action_c() cap msg rcvd for peer on interface Serial1/0 *Mar 1 12:35:16.718: DLSw: Recv CapExId Msg from peer on interface Serial1/0 *Mar 1 12:35:16.718: DLSw: received fhpr capex from peer on interface Serial1/0: support: false, fst-prio: false *Mar 1 12:35:16.722: DLSw: Pos CapExResp sent to peer on interface Serial1/0 *Mar 1 12:35:16.722: DLSw: CapExId Msg sent to peer on interface Serial1/0 *Mar 1 12:35:16.722: DLSw: END-FSTPFSM (peer on interface Serial1/0): state:DISCONN->WAIT_CAP *Mar 1 12:35:16.870: DLSw: START-FSTPFSM (peer on interface Serial1/0): event:SSP-CAP MSG RCVD state:WAIT_CAP *Mar 1 12:35:16.870: DLSw: dfstp_action_e() cap msg rcvd for peer on interface Serial1/0 *Mar 1 12:35:16.870: DLSw: Recv CapExPosRsp Msg from peer on interface Serial1/0 *Mar 1 12:35:16.870: DLSw: END-FSTPFSM (peer on interface Se R2#sh dlsw rial1/0): state:WAIT_CAP->WAIT_CAP *Mar 1 12:35:16.870: DLSw: Processing delayed event:SSP-CAP EXCHANGED - prev state:WAIT_CAP *Mar 1 12:35:16.870: DLSw: START-FSTPFSM (peer on interface Serial1/0): event:SSP-CAP EXCHANGED state:WAIT_CAP *Mar 1 12:35:16.874: DLSw: dfstp_action_f() cap xchged for peer on interface Serial1/0 *Mar 1 12:35:16.874: %DLSWP-3-PLFCHANGE: WAN media mtu maximum is 516; lowering peer lf *Mar 1 12:35:16.874: DLSw: END-FSTPFSM (peer on interface Serial1/0): state:WAIT_CAP->CONNECT R2#sh dlsw          *Mar 1 12:35:47.044: DLSw: Keepalive Request sent to peer on interface Serial1/0) *Mar 1 12:35:47.056: DLSw: Keepalive Response from peer on interface Serial1/0 R2#u all All possible debugging has been turned off R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se1/0 201 CONNECT 3 3 conf 0 - - 00:00:48 Total number of connected peers: 1 Total number of connections: 1 R2# R2# R2# R2# R2# R2# RACK14AS>1 [Resuming connection 1 to r1 ... ] * R1(config-if)#^Z R1#sh run *Mar 1 12:38:51.310: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | i dlsw dlsw local-peer peer-id 17.57.100.1 dlsw remote-peer 0 frame-relay interface Serial0/0 102 pass-thru frame-relay map dlsw 102 broadcast R1#sh run int s -0  0/0 Building configuration... Current configuration : 167 bytes ! interface Serial0/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map dlsw 102 broadcast end R1# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | i dlsw dlsw local-peer peer-id 200.1.1.2 dlsw remote-peer 0 frame-relay interface Serial1/0 201 pass-thru frame-relay map dlsw 201 broadcast R2#sh run int s 1/0 Building configuration... Current configuration : 167 bytes ! interface Serial1/0 ip address 180.40.7.65 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map dlsw 201 broadcast end R2# R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#dlsw remote R2(config)#dlsw remote-peer 0 ? frame-relay Use Frame Relay for remote peer transport fst Use fast sequence transport (FST) for remote peer transport interface Use a direct interface for remote peer transport tcp Use TCP for remote peer transport R2(config)#dlsw remote-peer 0 fst ? A.B.C.D Remote FST peer's IP address R2(config)#dlsw remote-peer 0 fst 180.40.7.129 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets passive Local peer will not initiate this remote peer connection rsvp Configure reservations using RSVP R2(config)#dlsw remote-peer 0 fst 180.40.7.129 R2(config)# R2(config)# R2(config)# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#dlsw local peer ? A.B.C.D Local Peer IP address R3(config)#dlsw local peer 200.1.1.2         180./ 40.7.129 R3(config)#dlsw remot R3(config)#dlsw remote-peer - 09 R3(config)#dlsw remote-peer 09  fst ? A.B.C.D Remote FST peer's IP address R3(config)#dlsw remote-peer 0 fst 200.1.1.2 R3(config)#^Z R3# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2(config)#^Z R2#sh *Mar 1 12:40:45.489: %SYS-5-CONFIG_I: Configured from console by console R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se1/0 201 CONNECT 13 13 conf 0 - - 00:05:32 FST 180.40.7.129 DISCONN 0 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se1/0 201 CONNECT 13 13 conf 0 - - 00:05:33 FST 180.40.7.129 DISCONN 0 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se1/0 201 CONNECT 13 13 conf 0 - - 00:05:40 FST 180.40.7.129 CONNECT 2 2 conf 0 - - 00:00:05 Expected: 0 Next Send: 0 Seq errors: 0 Total number of connected peers: 2 Total number of connections: 2 R2# R2# R2# R2#sh run | i dlsw dlsw local-peer peer-id 200.1.1.2 dlsw remote-peer 0 frame-relay interface Serial1/0 201 pass-thru dlsw remote-peer 0 fst 180.40.7.129 frame-relay map dlsw 201 broadcast R2# R2# R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run | i dlsw dlsw local-peer peer-id 180.40.7.129 dlsw remote-peer 0 fst 200.1.1.2 R3# R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#dlsw loca R4(config)#dlsw local-peer peer R4(config)#dlsw local-peer peer-id 180.490.   0.7.120  309  R4(config)#dlsw remote R4(config)#dlsw remote-peer ? <0-4095> Remote peer ring group list R4(config)#dlsw remote-peer 0 ? frame-relay Use Frame Relay for remote peer transport fst Use fast sequence transport (FST) for remote peer transport interface Use a direct interface for remote peer transport tcp Use TCP for remote peer transport R4(config)#dlsw remote-peer 0 tcp ? A.B.C.D Remote peer IP address R4(config)#dlsw remote-peer 0 tcp 2001 .1.1.2 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses dynamic Enable dynamic connection for this remote peer host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets passive Local peer will not initiate this remote peer connection priority Enable prioritization features for this remote peer rif-passthru Use rif_passthru for this remote peer rsvp Configure reservations using RSVP tcp-queue-max Maximum output TCP queue size for this remote peer timeout Set retransmission timeout value for this remote peer R4(config)#dlsw remote-peer 0 tcp 200.1.1.2 R4(config)# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#loca    dlsw lov cal peer 2001.  .1.1.2 ? biu-segment XID3 max receivable i-field spoofing and BIU segmenting border Capable of operating as a border peer cluster Set cluster id for this router cost Set peer cost advertised to remote peers group Set the peer group number for this router init-pacing-window Initial Pacing Window Size for this local peer keepalive Set the default remote peer keepalive interval lf Local peer largest frame size max-pacing-window Maximum Pacing Window Size for this local peer passive This router will not initiate remote peer connections peer-id local-peer IP address; required for TCP/FST and peer groups promiscuous Accept connections from non-configured remote peers R2(config)#dlsw local peer 200.1.1.2 promiscuous %promiscuous change will not affect existing peer connections R2(config)# R2(config)# R2(config)# R2(config)# R2(config)# R2(config)#^Z R2#sh *Mar 1 12:45:36.045: %SYS-5-CONFIG_I: Configured from console by console R2#sh run I   | i dlsw dlsw local-peer peer-id 200.1.1.2 promiscuous dlsw remote-peer 0 frame-relay interface Serial1/0 201 pass-thru dlsw remote-peer 0 fst 180.40.7.129 frame-relay map dlsw 201 broadcast R2# R2# R2# R2# R2# R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime IF Se1/0 201 CONNECT 23 23 conf 0 - - 00:10:41 FST 180.40.7.129 CONNECT 12 12 conf 0 - - 00:05:06 Expected: 0 Next Send: 0 Seq errors: 0 TCP 180.40.7.130 CONNECT 3 3 prom 0 0 0 00:00:45 Total number of connected peers: 3 Total number of connections: 3 R2# R2# R2# R2# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4(config)#^Z R4#sh run | *Mar 1 12:50:31.060: %SYS-5-CONFIG_I: Configured from console by console R4#sh run | i dlsw dlsw local-peer peer-id 180.40.7.130 dlsw remote-peer 0 tcp 200.1.1.2 R4# R4# RACK14AS>1` % Unknown command or computer name, or unable to find computer address RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do u allsh run | i dlswint s 0/0 fram map dlsw 102 broadcast int s 0/0 dlsw remote-peer 0 frame-relay interface ser 0/0 102 pass-thru ndlsw remote-peer 0 frame-relay interface ser 0/0 102 pass-thru odlsw remote-peer 0 frame-relay interface ser 0/0 102 pass-thru  dlsw remote-peer 0 frame-relay interface ser 0/0 102 pass-thru  R1(config)#no dlsw remote-peer 0 frame-relay interface ser 0/0 102 pass-thru            no dlsw remote-peer 0 frame-relay interface ser 0/0 102 dlsw remote-peer 0 frame-relay interface ser 0/0 102 dlsw remote-peer 0 frame-relay interface ser 0/0 102  R1(config)#^x2 ^ % Invalid input detected at '^' marker. R1(config)# R1(config)# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#do sh run | i dlsw dlsw local-peer peer-id 200.1.1.2 promiscuous dlsw remote-peer 0 frame-relay interface Serial1/0 201 pass-thru dlsw remote-peer 0 fst 180.40.7.129 frame-relay map dlsw 201 broadcast R2(config)#no dlsw remote-peer 0 frame-relay interface Serial1/0 201 pass-thr$ote-peer 0 frame-relay interface Serial1/0 201 pass-thru  R2(config)#$ote-peer 0 frame-relay interface Serial1/0 201 pass-thru         no dlsw remote-peer 0 frame-relay interface Serial1/0 201 no dlsw remote-peer 0 frame-relay interface Serial1/0 201 dlsw remote-peer 0 frame-relay interface Serial1/0 201 dlsw remote-peer 0 frame-relay interface Serial1/0 201  R2(config)#do sh dlsw sh dlsw % Incomplete command. R2(config)#do sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime FST 180.40.7.129 CONNECT 19 19 conf 0 - - 00:08:57 Expected: 0 Next Send: 0 Seq errors: 0 TCP 180.40.7.130 CONNECT 11 11 prom 0 0 0 00:04:36 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 2 Total number of connections: 2 R2(config)#int s 0/  1/0 R2(config-if)#do sh run int s 1/0 Building configuration... Current configuration : 167 bytes ! interface Serial1/0 ip address 180.40.7.65 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map dlsw 201 broadcast end R2(config-if)#no frame-relay map dlsw 201 broadcast R2(config-if)#fra R2(config-if)#fra m   R2(config-if)#fram R2(config-if)#frame-relay ,a  map ? appletalk AppleTalk bridge Bridging bstun Block Serial Tunnel clns ISO CLNS decnet DECnet dlsw Data Link Switching ip IP ipv6 IPV6 ipx Novell IPX llc2 llc2 pppoe PPP over Ethernet qllc qllc protocol rsrb Remote Source-Route Bridging stun Serial Tunnel R2(config-if)#frame-relay map ll R2(config-if)#frame-relay map llc2 ? <16-1007> DLCI vc-bundle vc-bundle R2(config-if)#frame-relay map llc2 201 bro R2(config-if)#frame-relay map llc2 201 broadcast R2(config-if)#^Z R2# RACK14AS>2 1 [Resuming connection 1 to r1 ... ] R1(config)#iutn     tn  nt s 1 0/0 R1(config-if)#no fram map dlsw 102 br R1(config-if)#fram map ll 102 bri ^ % Invalid input detected at '^' marker. R1(config-if)#fram map ll 102 bri  R1(config-if)#^Z R1#sh *Mar 1 12:52:02.323: %SYS-5-CONFIG_I: Configured from console by console R1#sh dlsw % Incomplete command. R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 CONNECT 2 2 conf 0 0 - 00:00:00 Total number of connected peers: 1 Total number of connections: 1 R1# *Mar 1 12:52:05.952: %DLSWP-3-PLFCHANGE: WAN media mtu maximum is 516; lowering peer lf R1# R1# R1# R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 CONNECT 2 2 conf 0 0 - 00:00:03 Total number of connected peers: 1 Total number of connections: 1 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 CONNECT 2 2 conf 0 0 - 00:00:04 Total number of connected peers: 1 Total number of connections: 1 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 CONNECT 2 2 conf 0 0 - 00:00:05 Total number of connected peers: 1 Total number of connections: 1 R1#sh eun     run | i dlsw dlsw local-peer peer-id 17.57.100.1 dlsw remote-peer 0 frame-relay interface Serial0/0 102 R1#sh run int s 0/0 Building configuration... Current configuration : 168 bytes ! interface Serial0/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map llc2 102 broadcast end R1# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run | i dlsw dlsw local-peer peer-id 200.1.1.2 promiscuous dlsw remote-peer 0 fst 180.40.7.129 dlsw remote-peer 0 frame-relay interface Serial1/0 201 R2#sh run int s 1/0 Building configuration... Current configuration : 168 bytes ! interface Serial1/0 ip address 180.40.7.65 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map llc2 201 broadcast end R2# R2#confg ig t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#bri R2(config)#bridge 1 pr R2(config)#bridge 1 pro R2(config)#bridge 1 protocol iee R2(config)#int fa /1 ^ % Invalid input detected at '^' marker. R2(config)#int fa /10/1 R2(config-if)#bri R2(config-if)#bridge-group 1 R2(config-if)#ezxi   xit R2(config)#dslw ? % Unrecognized command R2(config)#dslw dlsw ? % Unrecognized command R2(config)#dslw dlsw  dlsw  dlsw  dlsw  dlsw  dlsw ? allroute-netbios Use All routes Broadcast for NETBIOS Explorers allroute-sna Use All routes Broadcast for SNA Explorers bgroup-list Configure a transparent bridge group list bridge-group DLSw interconnection to transparent bridging cache-ignore-netbios-datagram Don't cache source mac/name of NetBIOS datagrams circuit-keepalives Configure DLSw+ to generate periodic circuit keepalives disable Disable DLSw without altering the configuration explorerQ-depth Configure depth of DLSw control queues fast-hpr-support Enable fast-switched HPR transport group-cache Border Peer Caching Options history-log Configure DLSw Circuit-History Log Capability icannotreach Configure a resource not locally reachable by this router icanreach Configure resources locally reachable by this router llc2 Dlsw llc2 options load-balance Configure load balancing local-peer Configure local peer mac-addr Configure a static MAC address - location or --More--   R2(config)# dlsw b bri R2(config)# dlsw bridge-group ? <1-255> Assign a Bridge Group to be assigned to DLSw R2(config)# dlsw bridge-group 1 ? llc2 LLC2 Interface Subcommands locaddr-priority Assign an input SNA LU Addr priority list to this bridge group sap-priority Assign an input sap priority list to this bridge group R2(config)# dlsw bridge-group 1 R2(config)# *Mar 1 12:54:34.520: %LINEPROTO-5-UPDOWN: Line protocol on Interface DLSw Port0, changed state to up R2(config)#^Z R2# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#brid 1 pro iee R1(config)#int e 0/0 R1(config-if)#bri R1(config-if)#bridge-group 1 R1(config-if)#exit R1(config)#dls  w bri 1 R1(config)#^Z R1# RACK14AS>34 % 34 is not an open connection RACK14AS> [Resuming connection 1 to r1 ... ] * R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#bri1 pro iee ^ % Invalid input detected at '^' marker. R3(config)#bri1 pro iee 1 pro iee R3(config)#dlsw bri 1 R3(config)#inm *Mar 1 12:55:30.884: Note: A random Spanning Tree Bridge Identifier address of 0000.0c6b.0148 has been chosen for Bridge Group 1 since there is no mac address associated with the selected interface. *Mar 1 12:55:30.884: Ensure that this address is unique. *Mar 1 12:55:31.886: %LINEPROTO-5-UPDOWN: Line protocol on Interface DLSw Port0, changed state to up R3(config)#inmt  t e fd a 0/1 R3(config-if)#bri 1 ^ % Invalid input detected at '^' marker. R3(config-if)#bri 1    R3(config-if)#bridge-group 1 R3(config-if)#^Z R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#bri R4(config)#bridge 1 pro iee R4(config)#dlsw bri 1 R4(config)#int *Mar 1 12:58:27.712: Note: A random Spanning Tree Bridge Identifier address of 0000.0cc2.b404 has been chosen for Bridge Group 1 since there is no mac address associated with the selected interface. *Mar 1 12:58:27.716: Ensure that this address is unique. *Mar 1 12:58:28.712: %LINEPROTO-5-UPDOWN: Line protocol on Interface DLSw Port0, changed state to up R4(config)#int fa 0/0 R4(config-if)#bri R4(config-if)#bridge-group 1 R4(config-if)#^Z R4# *Mar 1 12:58:33.988: %SYS-5-CONFIG_I: Configured from console by console R4# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | i dlsw dlsw local-peer peer-id 17.57.100.1 dlsw remote-peer 0 frame-relay interface Serial0/0 102 dlsw bridge-group 1 R1#sh run int e 0/0 Building configuration... Current configuration : 96 bytes ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 half-duplex bridge-group 1 end R1# R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#no % Incomplete command. R1(config)#RACK14AS>1 ^ % Invalid input detected at '^' marker. R1(config)#no dlsw remote-peer 0 frame-relay interface Serial0/0 102 R1(config)#no dlsw remote-peer 0 frame-relay interface Serial0/0 102no dlsw remote-peer 0 frame-relay interface Serial0/0 102  dlsw remote-peer 0 frame-relay interface Serial0/0 102  dlsw remote-peer 0 frame-relay interface Serial0/0 102 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets pass-thru Remote peer is capable of locally acknowledging DLC sessions passive Local peer will not initiate this remote peer connection rsvp Configure reservations using RSVP R1(config)# dlsw remote-peer 0 frame-relay interface Serial0/0 102                                                         dlsw local-peer peer-id 17.57.100.1 ? biu-segment XID3 max receivable i-field spoofing and BIU segmenting border Capable of operating as a border peer cluster Set cluster id for this router cost Set peer cost advertised to remote peers group Set the peer group number for this router init-pacing-window Initial Pacing Window Size for this local peer keepalive Set the default remote peer keepalive interval lf Local peer largest frame size max-pacing-window Maximum Pacing Window Size for this local peer passive This router will not initiate remote peer connections peer-id local-peer IP address; required for TCP/FST and peer groups promiscuous Accept connections from non-configured remote peers R1(config)#dlsw local-peer peer-id 17.57.100.1 gr R1(config)#dlsw local-peer peer-id 17.57.100.1 group ? <1-255> Peer group number R1(config)#dlsw local-peer peer-id 17.57.100.1 group 2 % Incomplete command. R1(config)#dlsw local-peer peer-id 17.57.100.1 group 2 ? biu-segment XID3 max receivable i-field spoofing and BIU segmenting border Capable of operating as a border peer cluster Set cluster id for this router cost Set peer cost advertised to remote peers init-pacing-window Initial Pacing Window Size for this local peer keepalive Set the default remote peer keepalive interval lf Local peer largest frame size max-pacing-window Maximum Pacing Window Size for this local peer passive This router will not initiate remote peer connections promiscuous Accept connections from non-configured remote peers R1(config)#dlsw local-peer peer-id 17.57.100.1 group 2 ke  cost ? <1-5> DLSw Local Peer Cost R1(config)#dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 ? biu-segment XID3 max receivable i-field spoofing and BIU segmenting border Capable of operating as a border peer cluster Set cluster id for this router cost Set peer cost advertised to remote peers group Set the peer group number for this router init-pacing-window Initial Pacing Window Size for this local peer keepalive Set the default remote peer keepalive interval lf Local peer largest frame size max-pacing-window Maximum Pacing Window Size for this local peer passive This router will not initiate remote peer connections peer-id local-peer IP address; required for TCP/FST and peer groups promiscuous Accept connections from non-configured remote peers R1(config)#dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 %Must remove local-peer to change peer group R1(config)# R1(config)# R1(config)# R1(config)# R1(config)#dlsw local-peer peer-id 17.57.100.1 group 2 cost 2                 ndlsw local-peer peer-id 17.57.100.1odlsw local-peer peer-id 17.57.100.1 dlsw local-peer peer-id 17.57.100.1 R1(config)#no dlsw local-peer peer-id 17.57.100.1dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 R1(config)#do sh ru | i dlsw % Ambiguous command: "sh ru " R1(config)#do sh ru | i dlswn | i dlsw dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 R1(config)# R1(config)# R1(config)# R1(config)# R1(config)# R1(config)# R1(config)#dlsw bridge-group 1 R1(config)# *Mar 1 13:02:41.578: %LINEPROTO-5-UPDOWN: Line protocol on Interface DLSw Port0, changed state to up R1(config)# R1(config)#dlsw bridge-group 1o sh run | i dlsw  | i dlsw lsw local-peer peer-id 17.57.100.1 group 2 cost 2 no dlsw local-peer peer-id 17.57.100.1 dlsw local-peer peer-id 17.57.100.1 group 2 cost 2  no dlsw remote-peer 0 frame-relay interface Serial0/0 102no dlsw remote-peer 0 frame-relay interface Serial0/0 102  dlsw remote-peer 0 frame-relay interface Serial0/0 102  R1(config)#^Z R1# *Mar 1 13:03:34.910: %SYS-5-CONFIG_I: Configured from console by console R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run | i dls dlsw local-peer peer-id 180.40.7.129 dlsw remote-peer 0 fst 200.1.1.2 dlsw bridge-group 1 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no dlsw local-peer peer-id 180.40.7.129 R3(config)#no dlsw local-peer peer-id 180.40.7.129 grou 2 cvo   pr R3(config)#no dlsw local-peer peer-id 180.40.7.129 grou 2 pro R3(config)#no dlsw local-peer peer-id 180.40.7.129 grou 2 prom R3(config)#no dlsw local-peer peer-id 180.40.7.129 grou 2 promno dlsw local-peer peer-id 180.40.7.129 grou 2 prom  dlsw local-peer peer-id 180.40.7.129 grou 2 prom  dlsw local-peer peer-id 180.40.7.129 grou 2 prom R3(config)# dlsw local-peer peer-id 180.40.7.129 grou 2 promiscuous R3(config)#dlsw remote-peer 0 fst 200.1.1.2 R3(config)#dlsw bridge-group 1 R3(config)#^Z R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#do sh run | i dlsw dlsw local-peer peer-id 180.40.7.130 dlsw remote-peer 0 tcp 200.1.1.2 dlsw bridge-group 1 R4(config)#no dlsw local-peer peer-id 180.40.7.130 R4(config)#dlsw local-peer peer-id 180.40.7.130 grou 2 pro R4(config)#dlsw remote-peer 0 tcp 200.1.1.2 R4(config)#dlsw bridge-group 1 R4(config)#^Z R4# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run | i dlsw dlsw local-peer peer-id 200.1.1.2 promiscuous dlsw remote-peer 0 frame-relay interface Serial1/0 201 dlsw remote-peer 0 fst 180.40.7.129 dlsw bridge-group 1 R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#no -dlsw remote-peer 0 tcp 200.1.1.2 ^ % Invalid input detected at '^' marker. R2(config)#dlsw bridge-group 1 %DLSw already attached to the transparent bridge group. R2(config)#dlsw local-peer peer-id 200.1.1.2 promiscuous R2(config)#mp  dlsw local-peer peer-id 200.1.1.2 promiscuousndlsw local-peer peer-id 200.1.1.2 promiscuousodlsw local-peer peer-id 200.1.1.2 promiscuous dlsw local-peer peer-id 200.1.1.2 promiscuous R2(config)#dlsw local-peer peer-id 200.1.1.2 ? biu-segment XID3 max receivable i-field spoofing and BIU segmenting border Capable of operating as a border peer cluster Set cluster id for this router cost Set peer cost advertised to remote peers group Set the peer group number for this router init-pacing-window Initial Pacing Window Size for this local peer keepalive Set the default remote peer keepalive interval lf Local peer largest frame size max-pacing-window Maximum Pacing Window Size for this local peer passive This router will not initiate remote peer connections peer-id local-peer IP address; required for TCP/FST and peer groups promiscuous Accept connections from non-configured remote peers R2(config)#dlsw local-peer peer-id 200.1.1.2 bor R2(config)#dlsw local-peer peer-id 200.1.1.2 border ? biu-segment XID3 max receivable i-field spoofing and BIU segmenting border Capable of operating as a border peer cluster Set cluster id for this router cost Set peer cost advertised to remote peers group Set the peer group number for this router init-pacing-window Initial Pacing Window Size for this local peer keepalive Set the default remote peer keepalive interval lf Local peer largest frame size max-pacing-window Maximum Pacing Window Size for this local peer passive This router will not initiate remote peer connections peer-id local-peer IP address; required for TCP/FST and peer groups promiscuous Accept connections from non-configured remote peers R2(config)#dlsw local-peer peer-id 200.1.1.2 border grou 2 pro R2(config)#dlsw local-peer peer-id 200.1.1.2 border grou 2 promiscuous R2(config)#dlsw remote-peer 0 frame-relay interface Serial1/0 201 R2(config)#dlsw remote-peer 0 fst 180.40.7.129 R2(config)#dlsw bridge-group 1 R2(config)#^Z R2# *Mar 1 13:05:00.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface DLSw Port0, changed state to up *Mar 1 13:05:01.043: %SYS-5-CONFIG_I: Configured from console by console R2#do    sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 2 2 prom 0 0 0 00:00:08 FST 180.40.7.129 DISCONN 1 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 2 2 prom 0 0 0 00:00:19 FST 180.40.7.129 DISCONN 2 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 ROS_SENT 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 2 2 prom 0 0 0 00:00:21 FST 180.40.7.129 DISCONN 2 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 2 2 prom 0 0 0 00:00:23 FST 180.40.7.129 DISCONN 2 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:24 FST 180.40.7.129 DISCONN 2 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:25 FST 180.40.7.129 DISCONN 3 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:27 FST 180.40.7.129 DISCONN 3 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:28 FST 180.40.7.129 DISCONN 3 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:30 FST 180.40.7.129 DISCONN 3 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 4 3 prom 0 0 0 00:00:31 FST 180.40.7.129 DISCONN 3 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 4 3 prom 0 0 0 00:00:32 FST 180.40.7.129 DISCONN 3 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#dlsw di R2#dlsw dia R2#dlsw dia sa R2#dlsw disa? % Unrecognized command R2#dlsw disa         config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#dls w3   w   w dis R2(config)#dlsw disable ? R2(config)#dlsw disable R2(config)#dlsw disable ndlsw disable odlsw disable  dlsw disable  R2(config)#^Z R2#config t *Mar 1 13:06:09.403: %SYS-5-CONFIG_I: Configured from console by console R2#config tsh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime FST 180.40.7.129 WAIT_CAP 0 1 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 ROS_SENT 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime FST 180.40.7.129 DISCONN 0 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime FST 180.40.7.129 DISCONN 0 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime FST 180.40.7.129 DISCONN 0 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - TCP 180.40.7.130 WAIT_CAP 0 0 prom 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 2 2 prom 0 0 0 00:00:01 FST 180.40.7.129 DISCONN 0 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:03 FST 180.40.7.129 DISCONN 0 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:10 FST 180.40.7.129 CONNECT 2 2 conf 0 - - 00:00:06 Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 ROS_SENT 0 0 conf 0 0 - - Total number of connected peers: 2 Total number of connections: 2 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:13 FST 180.40.7.129 CONNECT 2 2 conf 0 - - 00:00:09 Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 ROS_SENT 0 0 conf 0 0 - - Total number of connected peers: 2 Total number of connections: 2 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:15 FST 180.40.7.129 CONNECT 2 2 conf 0 - - 00:00:11 Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 ROS_SENT 0 0 conf 0 0 - - Total number of connected peers: 2 Total number of connections: 2 R2#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 180.40.7.130 CONNECT 3 2 prom 0 0 0 00:00:16 FST 180.40.7.129 CONNECT 2 2 conf 0 - - 00:00:12 Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 2 Total number of connections: 2 R2# RACK14AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#dlsw dis R1(config)#dlsw disndlsw disodlsw dis dlsw dis R1(config)#^Z R1#sh *Mar 1 13:07:55.365: %SYS-5-CONFIG_I: Configured from console by console R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 CON_PEND 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 CON_PEND 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R1#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se0/0 102 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R1#deb dlks  sw DLSw reachability debugging is on at event level for all protocol traffic DLSw peer debugging is on DLSw local circuit debugging is on DLSw core message debugging is on DLSw core state debugging is on DLSw core flow control debugging is on DLSw core xid debugging is on R1# *Mar 1 13:08:16.423: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:ADMIN-OPEN CONNECTION state:DISCONN *Mar 1 13:08:16.423: DLSw: dllc2p_action_a() attempting to connect peer on interface Serial0/0 *Mar 1 13:08:16.423: PEER-DISP Sent : CLSI Msg : REQ_OPNSTN.Req dlen: 116 *Mar 1 13:08:16.423: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:DISCONN->ROS_SENT *Mar 1 13:08:16.427: DLSw: Peer Received : CLSI Msg : REQ_OPNSTN.Cfm CLS_OK dlen: 116 *Mar 1 13:08:16.427: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:CLS-REQOPNSTN.CNF state:ROS_SENT *Mar 1 13:08:16.427: DLSw: dllc2p_action_c() R1# *Mar 1 13:08:16.427: PEER-DISP Sent : CLSI Msg : CONNECT.Req dlen: 16 *Mar 1 13:08:16.427: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:ROS_SENT->CON_PEND R1# *Mar 1 13:08:22.469: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:TIMER-TIMER EXPIRED state:CON_PEND *Mar 1 13:08:22.469: DLSw: dllc2p_action_b() *Mar 1 13:08:22.473: PEER-DISP Sent : CLSI Msg : CLOSE_STN.Req dlen: 4 *Mar 1 13:08:22.473: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:CON_PEND->CLO_PEND *Mar 1 13:08:22.473: DLSw: Peer Received : CLSI Msg : CLOSE_STN.Cfm CLS_OK dlen: 8 *Mar 1 13:08:22.473: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:CLS-CLOSESTN.CNF state:CLO_PEND *Mar 1 13:08:22.473: DLSw: dllc2p_action_d() disconnect peer on interface Serial0/0 R1# *Mar 1 13:08:22.477: DLSw: LLC2 peer aborting connection for peer on interface Serial0/0 *Mar 1 13:08:22.477: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:CLO_PEND->DISCONN R1# *Mar 1 13:08:37.654: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:ADMIN-OPEN CONNECTION state:DISCONN *Mar 1 13:08:37.654: DLSw: dllc2p_action_a() attempting to connect peer on interface Serial0/0 *Mar 1 13:08:37.654: PEER-DISP Sent : CLSI Msg : REQ_OPNSTN.Req dlen: 116 *Mar 1 13:08:37.654: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:DISCONN->ROS_SENT *Mar 1 13:08:37.658: DLSw: Peer Received : CLSI Msg : REQ_OPNSTN.Cfm CLS_OK dlen: 116 *Mar 1 13:08:37.658: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:CLS-REQOPNSTN.CNF state:ROS_SENT *Mar 1 13:08:37.658: DLSw: dllc2p_action_c() R1#^Z R1# *Mar 1 13:08:37.658: PEER-DISP Sent : CLSI Msg : CONNECT.Req dlen: 16 *Mar 1 13:08:37.658: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:ROS_SENT->CON_PEND R1#u all All possible debugging has been turned off R1#2 Trying 2... % Destination unreachable; gateway or host down % Unknown command or computer name, or unable to find computer address R1# R1# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#deb dlsw DLSw reachability debugging is on at event level for all protocol traffic DLSw peer debugging is on DLSw local circuit debugging is on DLSw core message debugging is on DLSw core state debugging is on DLSw core flow control debugging is on DLSw core xid debugging is on R2# *Mar 1 13:07:54.399: DLSw: Keepalive Request sent to peer 180.40.7.130(2065)) R2# *Mar 1 13:07:56.378: DLSw: START-FSTPFSM (peer 180.40.7.129(0)): event:DLX-KEEPALIVE REQ state:CONNECT *Mar 1 13:07:56.378: DLSw: dfstp_action_g() keepalive request from peer 180.40.7.129(0) *Mar 1 13:07:56.378: DLSw: Keepalive Response sent to peer 180.40.7.129(0)) *Mar 1 13:07:56.378: DLSw: END-FSTPFSM (peer 180.40.7.129(0)): state:CONNECT->CONNECT R2# R2# R2# R2# R2# *Mar 1 13:08:10.430: DLSw: START-LLC2PFSM (peer on interface Serial1/0): event:ADMIN-OPEN CONNECTION state:DISCONN *Mar 1 13:08:10.430: DLSw: dllc2p_action_a() attempting to connect peer on interface Serial1/0 *Mar 1 13:08:10.430: PEER-DISP Sent : CLSI Msg : REQ_OPNSTN.Req dlen: 116 *Mar 1 13:08:10.430: DLSw: END-LLC2PFSM (peer on interface Serial1/0): state:DISCONN->ROS_SENT *Mar 1 13:08:10.430: DLSw: Peer Received : CLSI Msg : REQ_OPNSTN.Cfm UNKNOWN_SAP dlen: 116 *Mar 1 13:08:10.430: DLSw: Invalid_peer(): peer:0 R2# *Mar 1 13:08:10.434: %DLSWP-3-PGENERAL: Invalid_peer -Traceback= 8101CB28 8101B828 80FF8E4C 803CE494 *Mar 1 13:08:12.052: %DLSWC-3-RECVSSP: SSP OP = 20( DATA ) from peer 180.40.7.129(0) R2# *Mar 1 13:08:12.056: DISP Sent : CLSI Msg : UDATA_STN.Req dlen: 83 *Mar 1 13:08:12.056: send_to_group_members(): copy to peer 180.40.7.130 R2# *Mar 1 13:08:16.439: DLSw: START-LLC2PFSM (peer on interface Serial1/0): event:TIMER-TIMER EXPIRED state:ROS_SENT *Mar 1 13:08:16.439: DLSw: dllc2p_action_b() *Mar 1 13:08:16.439: PEER-DISP Sent : CLSI Msg : CLOSE_STN.Req dlen: 4 *Mar 1 13:08:16.439: DLSw: END-LLC2PFSM (peer on interface Serial1/0): state:ROS_SENT->CLO_PEND *Mar 1 13:08:16.439: DLSw: Peer Received : CLSI Msg : CLOSE_STN.Cfm UNKNOWN_CEP dlen: 4 *Mar 1 13:08:16.439: DLSW: cls confirm failed *Mar 1 13:08:16.443: DLSw: START-LLC2PFSM (peer on interface Serial1/0): event:CLS-CLS CNF FAIL state:CLO_PEND *Mar 1 13:08:16.443: DLSw: dllc2p_action_d() disconnect peer on interface Serial1/0 R2# *Mar 1 13:08:16.443: DLSw: LLC2 peer aborting connection for peer on interface Serial1/0 *Mar 1 13:08:16.443: DLSw: END-LLC2PFSM (peer on interface Serial1/0): state:CLO_PEND->DISCONN R2#u all All possible debugging has been turned off R2# RACK14AS>z 1 [Resuming connection 1 to r1 ... ] R1#2u alldeb dlsw DLSw reachability debugging is on at event level for all protocol traffic DLSw peer debugging is on DLSw local circuit debugging is on DLSw core message debugging is on DLSw core state debugging is on DLSw core flow control debugging is on DLSw core xid debugging is on R1# *Mar 1 13:09:56.003: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:ADMIN-OPEN CONNECTION state:DISCONN *Mar 1 13:09:56.003: DLSw: dllc2p_action_a() attempting to connect peer on interface Serial0/0 *Mar 1 13:09:56.003: PEER-DISP Sent : CLSI Msg : REQ_OPNSTN.Req dlen: 116 *Mar 1 13:09:56.007: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:DISCONN->ROS_SENT *Mar 1 13:09:56.007: DLSw: Peer Received : CLSI Msg : REQ_OPNSTN.Cfm CLS_OK dlen: 116 *Mar 1 13:09:56.007: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:CLS-REQOPNSTN.CNF state:ROS_SENT *Mar 1 13:09:56.007: DLSw: dllc2p_action_c() R1# *Mar 1 13:09:56.007: PEER-DISP Sent : CLSI Msg : CONNECT.Req dlen: 16 *Mar 1 13:09:56.011: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:ROS_SENT->CON_PEND R1# *Mar 1 13:10:02.020: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:TIMER-TIMER EXPIRED state:CON_PEND *Mar 1 13:10:02.020: DLSw: dllc2p_action_b() *Mar 1 13:10:02.020: PEER-DISP Sent : CLSI Msg : CLOSE_STN.Req dlen: 4 *Mar 1 13:10:02.020: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:CON_PEND->CLO_PEND *Mar 1 13:10:02.024: DLSw: Peer Received : CLSI Msg : CLOSE_STN.Cfm CLS_OK dlen: 8 *Mar 1 13:10:02.024: DLSw: START-LLC2PFSM (peer on interface Serial0/0): event:CLS-CLOSESTN.CNF state:CLO_PEND *Mar 1 13:10:02.024: DLSw: dllc2p_action_d() disconnect peer on interface Serial0/0 R1# *Mar 1 13:10:02.024: DLSw: LLC2 peer aborting connection for peer on interface Serial0/0 *Mar 1 13:10:02.024: DLSw: END-LLC2PFSM (peer on interface Serial0/0): state:CLO_PEND->DISCONN R1#u all All possible debugging has been turned off R1#sh ru  n | i dlsw dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 dlsw remote-peer 0 frame-relay interface Serial0/0 102 dlsw bridge-group 1 R1# RACK14AS>3 21  [Resuming connection 2 to r2 ... ] R2#sh run | i dlsw dlsw local-peer peer-id 200.1.1.2 group 2 border promiscuous dlsw remote-peer 0 fst 180.40.7.129 dlsw remote-peer 0 frame-relay interface Serial1/0 201 dlsw bridge-group 1 R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh run | i dlsw dlsw local-peer peer-id 180.40.7.129 group 2 promiscuous dlsw remote-peer 0 fst 200.1.1.2 dlsw bridge-group 1 R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#sh ru  n | i dlsw dlsw local-peer peer-id 180.40.7.130 group 2 promiscuous dlsw remote-peer 0 tcp 200.1.1.2 dlsw bridge-group 1 R4# R4# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#wr Building configuration... [OK] R1#reload Proceed with reload? [confirm] RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#wr Building configuration... [OK] R2# R2# R2# R2#reload Proceed with reload? [confirm] *Mar 1 13:11:45.606: %SYS-5-RELOAD: Reload requested by console. *Mar 1 13:11:45.702: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 13:11:45.702: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.66 on Serial1/0 from FULL to DOWN, Neighbor Down: Interface down or detached System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) Copyright (c) 2003 by cisco Systems, Inc. C2600 platform with 262144 Kbytes of main memory RACK14AS>4 [Resuming connection 4 to r4 ... ] R4# *Mar 1 13:14:28.156: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#sh access-list R4#confitg     t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#access-list 700 > ? deny Specify packets to reject permit Specify packets to forward R4(config)#access-list 700 per ? H.H.H 48-bit hardware address R4(config)#access-list 700 per 00c0.- 000  .0000 0.ffff.fffc R4(config)#do sh runb  | dlsw sh run | dlsw ^ % Invalid input detected at '^' marker. R4(config)#do sh run | dlswidlsw dlsw dlsw local-peer peer-id 180.40.7.130 group 2 promiscuous dlsw remote-peer 0 tcp 200.1.1.2 dlsw bridge-group 1 R4(config)#dlsw remote-peer 0 tcp 200.1.1.2 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses dynamic Enable dynamic connection for this remote peer host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets passive Local peer will not initiate this remote peer connection priority Enable prioritization features for this remote peer rif-passthru Use rif_passthru for this remote peer rsvp Configure reservations using RSVP tcp-queue-max Maximum output TCP queue size for this remote peer timeout Set retransmission timeout value for this remote peer R4(config)#dlsw remote-peer 0 tcp 200.1.1.2 dy R4(config)#dlsw remote-peer 0 tcp 200.1.1.2 dynamic ? bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses host-netbios-out Configure netbios host output filtering for this peer inactivity Dynamic peer inactivity keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets no-llc dynamic peer no LLC priority Enable prioritization features for this remote peer rif-passthru Use rif_passthru for this remote peer rsvp Configure reservations using RSVP tcp-queue-max Maximum output TCP queue size for this remote peer timeout Set retransmission timeout value for this remote peer R4(config)#dlsw remote-peer 0 tcp 200.1.1.2 dynamic dm R4(config)#dlsw remote-peer 0 tcp 200.1.1.2 dynamic dmac-output-list ? <700-799> access list number R4(config)#dlsw remote-peer 0 tcp 200.1.1.2 dynamic dmac-output-list 700 ? bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses host-netbios-out Configure netbios host output filtering for this peer inactivity Dynamic peer inactivity keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets no-llc dynamic peer no LLC priority Enable prioritization features for this remote peer rif-passthru Use rif_passthru for this remote peer rsvp Configure reservations using RSVP tcp-queue-max Maximum output TCP queue size for this remote peer timeout Set retransmission timeout value for this remote peer R4(config)#dlsw remote-peer 0 tcp 200.1.1.2 dynamic dmac-output-list 700 R4(config)#^Z R4# *Mar 1 13:19:18.428: %SYS-5-CONFIG_I: Configured from console by console R4#sh run | i dlsw dlsw local-peer peer-id 180.40.7.130 group 2 promiscuous dlsw remote-peer 0 tcp 200.1.1.2 keepalive 0 timeout 90 dynamic dmac-output-list 700 dlsw bridge-group 1 R4# R4#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 200.1.1.2 DISCONN 0 0 dynam 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R4# RACK14AS>2 [Resuming connection 2 to r2 ... ] progra R2> R2> R2> R2>en R2#sh run | i dlsw dlsw local-peer peer-id 200.1.1.2 group 2 border promiscuous dlsw remote-peer 0 frame-relay interface Serial1/0 201 dlsw remote-peer 0 fst 180.40.7.129 dlsw bridge-group 1 R2#sgh  h dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se1/0 201 CONNECT 11 20 conf 0 0 - 00:04:36 FST 180.40.7.129 CONNECT 19 10 conf 0 - - 00:04:15 Expected: 0 Next Send: 0 Seq errors: 0 Total number of connected peers: 2 Total number of connections: 2 R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#no dlsw local-peer peer-id 200.1.1.2 group 2 border promiscuous R2(config)#no dlsw local-peer peer-id 200.1.1.2 group 2 border promiscuousno dlsw local-peer peer-id 200.1.1.2 group 2 border promiscuous  dlsw local-peer peer-id 200.1.1.2 group 2 border promiscuous  dlsw local-peer peer-id 200.1.1.2 group 2 border promiscuous          a R2(config)# dlsw local-peer peer-id 200.1.1.2 group 2 border passive R2(config)#dlsw remote-peer 0 frame-relay interface Serial1/0 201 R2(config)#dlsw bridge-group 1 R2(config)# *Mar 1 00:08:08.007: %LINEPROTO-5-UPDOWN: Line protocol on Interface DLSw Port0, changed state to up R2(config)#dlsw remote-peer 0 fst 180.40.7.129 R2(config)#ds slw     lsw remote 0 tcp 180.40.7.130 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses dynamic Enable dynamic connection for this remote peer host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets passive Local peer will not initiate this remote peer connection priority Enable prioritization features for this remote peer rif-passthru Use rif_passthru for this remote peer rsvp Configure reservations using RSVP tcp-queue-max Maximum output TCP queue size for this remote peer timeout Set retransmission timeout value for this remote peer R2(config)#dlsw remote 0 tcp 180.40.7.130   R2(config)#^Z R2#sh reun     *Mar 1 00:09:03.446: %SYS-5-CONFIG_I: Configured from console by console R2#sh    config tsh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - FST 180.40.7.129 DISCONN 3 0 conf 0 - - - Expected: 0 Next Send: 0 Seq errors: 0 TCP 180.40.7.130 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 0 Total number of connections: 0 R2#sh dlsw peerconfig t sh dlsw peerrun | i dlswdlsw peer run | i dlsw dlsw local-peer peer-id 200.1.1.2 group 2 border passive dlsw remote-peer 0 fst 180.40.7.129 dlsw remote-peer 0 frame-relay interface Serial1/0 201 dlsw remote-peer 0 tcp 180.40.7.130 dlsw bridge-group 1 R2# R2#sh run | i dlswdlsw peer  Peers: state pkts_rx pkts_tx type drops ckts TCP uptime FST 180.40.7.129 CONNECT 6 2 conf 0 - - 00:00:24 Expected: 0 Next Send: 0 Seq errors: 0 LLC2 Se1/0 201 DISCONN 0 0 conf 0 0 - - TCP 180.40.7.130 DISCONN 0 0 conf 0 0 - - Total number of connected peers: 1 Total number of connections: 1 R2# RACK14AS>1 [Resuming connection 1 to r1 ... ] *Ma R1> R1>en R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#bri R1(config)#bridge 2 pro R1(config)#bridge 2 protocol iee R1(config)#int e 0/1 R1(config-if)#bri R1(config-if)#bridge-group 2 R1(config-if)#exit R1(config)#dlsw bri R1(config)#dlsw bridge-group 2 R1(config)# *Mar 1 00:12:11.150: %LINEPROTO-5-UPDOWN: Line protocol on Interface DLSw Port0, changed state to up R1(config)#dlsw ? allroute-netbios Use All routes Broadcast for NETBIOS Explorers allroute-sna Use All routes Broadcast for SNA Explorers bgroup-list Configure a transparent bridge group list bridge-group DLSw interconnection to transparent bridging cache-ignore-netbios-datagram Don't cache source mac/name of NetBIOS datagrams circuit-keepalives Configure DLSw+ to generate periodic circuit keepalives disable Disable DLSw without altering the configuration explorerQ-depth Configure depth of DLSw control queues fast-hpr-support Enable fast-switched HPR transport group-cache Border Peer Caching Options history-log Configure DLSw Circuit-History Log Capability icannotreach Configure a resource not locally reachable by this router icanreach Configure resources locally reachable by this router llc2 Dlsw llc2 options load-balance Configure load balancing local-peer Configure local peer mac-addr Configure a static MAC address - location or --More--   R1(config)#dlsw br R1(config)#dlsw bridge-group             gr R1(config)#dlsw bgroup-list ? <1-255> transparent bridge group list number R1(config)#dlsw bgroup-list 1 ? bgroups Required keyword before specifying transparent bridge group numbers R1(config)#dlsw bgroup-list 1 bg R1(config)#dlsw bgroup-list 1 bgroups ? <1-4095> Transparent bridge group number R1(config)#dlsw bgroup-list 1 bgroups 1 R1(config)#dlsw bgroup-list 1 bgroups 1   2 bgroups 2 2 bgroups 2 R1(config)#do sh run | i dlsw dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 0 frame-relay interface Serial0/0 102 dlsw bridge-group 1 dlsw bridge-group 2 R1(config)#no dlsw remote-peer 0 frame-relay interface Serial0/0 102 R1(config)#no dlsw remote-peer 0 frame-relay interface Serial0/0 102no dlsw remote-peer 0 frame-relay interface Serial0/0 102  dlsw remote-peer 0 frame-relay interface Serial0/0 102  dlsw remote-peer 0 frame-relay interface Serial0/0 102 1 frame-relay interface Serial0/0 102 R1(config)# dlsw remote-peer 1 frame-relay interface Serial0/0 102dlsw        dlsw remote 2 tcp 18- 0.40.7.129 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses dynamic Enable dynamic connection for this remote peer host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets passive Local peer will not initiate this remote peer connection priority Enable prioritization features for this remote peer rif-passthru Use rif_passthru for this remote peer rsvp Configure reservations using RSVP tcp-queue-max Maximum output TCP queue size for this remote peer timeout Set retransmission timeout value for this remote peer R1(config)#dlsw remote 2 tcp 180.40.7.129 R1(config)#^Z R1# *Mar 1 00:15:24.042: %SYS-5-CONFIG_I: Configured from console by console R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#bri R3(config)#bridge 2 pro R3(config)#bridge 2 protocol iee R3(config)#int e   fa 0/0 R3(config-if)#bri R3(config-if)#bridge-group 2 R3(config-if)#esdi   xit R3(config)#dlswe    bri R3(config)#dlsw bridge-group 2 R3(config)#dlsw b *Mar 1 13:31:31.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface DLSw Port0, changed state to up R3(config)#dlsw bg R3(config)#dlsw bgroup-list 1 b R3(config)#dlsw bgroup-list 1 bgroups 1 R3(config)#dlsw bgroup-list 1 bgroups 1 2 bgroups 2 2 bgroups 2 R3(config)#do sh run | i dlsw dlsw local-peer peer-id 180.40.7.129 group 2 promiscuous dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 0 fst 200.1.1.2 dlsw bridge-group 1 dlsw bridge-group 2 R3(config)#no dlsw remote-peer 0 fst 200.1.1.2 R3(config)#no dlsw remote-peer 0 fst 200.1.1.20 fst 200.1.1.2 1 fst 200.1.1.2no dlsw remote-peer 1 fst 200.1.1.2  dlsw remote-peer 1 fst 200.1.1.2  R3(config)#dlsw tre   remote   R3(config)#dlsw remote-peer 2 tcp 17.57.100.1 %port-list change will not effect existing circuits R3(config)#do sh run | i dlsw dlsw local-peer peer-id 180.40.7.129 group 2 promiscuous dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 2 tcp 17.57.100.1 dlsw remote-peer 1 fst 200.1.1.2 dlsw bridge-group 1 dlsw bridge-group 2 R3(config)#int fa 0/09  R3(config-if)#no shut R3(config-if)# *Mar 1 13:32:52.900: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 13:32:53.901: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3(config-if)#^Z R3#sh dlsw *Mar 1 13:33:02.568: %SYS-5-CONFIG_I: Configured from console by console R3#sh dlsw peer Peers: state pkts_rx pkts_tx type drops ckts TCP uptime FST 200.1.1.2 CONNECT 2 3 conf 0 - - 00:00:23 Expected: 0 Next Send: 0 Seq errors: 0 TCP 17.57.100.1 CONNECT 8 9 conf 0 0 0 00:03:06 Total number of connected peers: 2 Total number of connections: 2 R3# R3# R3# R3#sh dlsw peer ? interface Specify a remote peer by a direct interface ip-address Specify a remote peer by it's ip address ssp-dlx Display DLSw peer SSP and DLX primative statistics udp Display DLSw peer UDP statistics | Output modifiers R3#sh dlsw peer ip 17.57.100.1 Peers: state pkts_rx pkts_tx type drops ckts TCP uptime TCP 17.57.100.1 CONNECT 8 10 conf 0 0 0 00:03:27 R3#sh dlsw peer ip 17.57.100.1 ? | Output modifiers R3#sh dlsw peer ip 17.57.100.1                     cap R3#sh dlsw capabilities ? interface Specify a remote peer by a direct interface ip-address Specify a remote peer by it's ip address local Specify the local DLSw peer | Output modifiers R3#sh dlsw capabilities DLSw: Capabilities for peer 200.1.1.2(0) vendor id (OUI) : '00C' (cisco) version number : 2 release number : 0 init pacing window : 20 unsupported saps : none num of tcp sessions : 1 loop prevent support : no icanreach mac-exclusive : no icanreach netbios-excl. : no reachable mac addresses : none reachable netbios names : none V2 multicast capable : yes DLSw multicast address : none cisco version number : 1 peer group number : 2 peer cluster support : yes border peer capable : yes peer cost : 3 biu-segment configured : no UDP Unicast support : yes Fast-switched HPR supp. : no NetBIOS Namecache length : 15 --More--   local-ack configured : yes priority configured : no cisco RSVP support : no configured ip address : 200.1.1.2 peer type : conf version string : Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-JK8O3S-M), Version 12.2(15)T14, RELEASE SOFTWARE (fc4) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2004 by cisco Systems, Inc. Compiled Sat 28-Aug-0 --More--  DLSw: Capabilities for peer 17.57.100.1(2065) vendor id (OUI) : '00C' (cisco) version number : 2 release number : 0 init pacing window : 20 unsupported saps : none num of tcp sessions : 1 loop prevent support : no icanreach mac-exclusive : no icanreach netbios-excl. : no reachable mac addresses : none reachable netbios names : none V2 multicast capable : yes DLSw multicast address : none cisco version number : 1 peer group number : 2 peer cluster support : yes border peer capable : no peer cost : 2 biu-segment configured : no UDP Unicast support : yes Fast-switched HPR supp. : no NetBIOS Namecache length : 15 --More--   local-ack configured : yes priority configured : no cisco RSVP support : no configured ip address : 17.57.100.1 peer type : conf version string : Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE SOFTWARE (fc4) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2004 by cisco Systems, Inc. Compiled Sat 28-Aug-04 R3#q sh dlsw ? capabilities Display DLSw capabilities information circuits Display DLSw circuit information fastcache Display DLSw fast cache for FST and Direct local-circuit Display DLSw local circuits peers Display DLSw peer information reachability Display DLSw reachability information statistics Display DLSw statistical information transparent Display MAC address mappings R3#sh dlsw cir R3#sh dlsw cir ? <0-4294967295> Circuit ID for a specific remote circuit detail Display full remote circuit details history Display remote circuit history mac-address Display all remote circuits using a specific MAC sap-value Display all remote circuits using a specific SAP | Output modifiers R3#sh dlsw cir             sh dlsw capabilities              re R3#sh dlsw reachability ? group Display DLSw group reachability (BP only) local Display DLSw local reachability mac-address Display DLSw mac address reachability netbios-names Display DLSw NetBIOS name reachability remote Display DLSw remote reachability | Output modifiers R3#sh dlsw reachability DLSw Local MAC address reachability cache list Mac Addr status Loc. port rif 00c8.0147.40c1 FOUND LOCAL TBridge-001 --no rif-- 00c8.01f3.73c0 FOUND LOCAL TBridge-002 --no rif-- DLSw Remote MAC address reachability cache list Mac Addr status Loc. peer DLSw Local NetBIOS Name reachability cache list NetBIOS Name status Loc. port rif DLSw Remote NetBIOS Name reachability cache list NetBIOS Name status Loc. peer R3# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | i dlsw dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 2 tcp 180.40.7.129 dlsw remote-peer 1 frame-relay interface Serial0/0 102 dlsw bridge-group 1 dlsw bridge-group 2 R1#sh run int e 0/1 Building configuration... Current configuration : 83 bytes ! interface Ethernet0/1 no ip address shutdown half-duplex bridge-group 2 end R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | i dlsw dlsw local-peer peer-id 180.40.7.129 group 2 promiscuous dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 1 fst 200.1.1.2 dlsw remote-peer 2 tcp 17.57.100.1 dlsw bridge-group 1 dlsw bridge-group 2 R3#sh run int fa 0/0 Building configuration... Current configuration : 89 bytes ! interface FastEthernet0/0 no ip address duplex auto speed auto bridge-group 2 end R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#neyt   R3(config)#net? netbios network-clock-participate network-clock-select R3(config)#netbi R3(config)#netbios ? access-list Define NETBIOS station access list name-cache Set name cache parameters R3(config)#netbios acc ? bytes NETBIOS byte offset access list filter-name-recognized Filter the Name Recognized frame host Assign name of access list to NETBIOS station[s] R3(config)#netbios acc ho ? WORD Access-list name R3(config)#netbios acc ho                200     access-list 200 den 0xf0f0 0x0001 R3(config)#access-list 2-0-   000 per  per  per - 0x0 0xc ffff R3(config)#dlsw remote R3(config)#dlsw remote-peer 2 access-list 200 per 0x0 0xffffden 0xf0f0 0x0001 no shut int fa 0/0do sh run | i dlswlsw remote-peer 2 tcp 17.57.100.1 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses dynamic Enable dynamic connection for this remote peer host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets passive Local peer will not initiate this remote peer connection priority Enable prioritization features for this remote peer rif-passthru Use rif_passthru for this remote peer rsvp Configure reservations using RSVP tcp-queue-max Maximum output TCP queue size for this remote peer timeout Set retransmission timeout value for this remote peer R3(config)#dlsw remote-peer 2 tcp 17.57.100.1 ls R3(config)#dlsw remote-peer 2 tcp 17.57.100.1 lsap-output-list ? <200-299> access list number R3(config)#dlsw remote-peer 2 tcp 17.57.100.1 lsap-output-list 200 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses dynamic Enable dynamic connection for this remote peer host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets passive Local peer will not initiate this remote peer connection priority Enable prioritization features for this remote peer rif-passthru Use rif_passthru for this remote peer rsvp Configure reservations using RSVP tcp-queue-max Maximum output TCP queue size for this remote peer timeout Set retransmission timeout value for this remote peer R3(config)#dlsw remote-peer 2 tcp 17.57.100.1 lsap-output-list 200 R3(config)#do sh run | i dlsw dlsw local-peer peer-id 180.40.7.129 group 2 promiscuous dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 1 fst 200.1.1.2 dlsw remote-peer 2 tcp 17.57.100.1 lsap-output-list 200 dlsw bridge-group 1 dlsw bridge-group 2 R3(config)#^Z R3# *Mar 1 13:38:06.626: %SYS-5-CONFIG_I: Configured from console by console R3# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#access-list 200 den 0xf0f0 0x0001 R1(config)#access-list 200 er 0x00  -0         per 0x0 0ff  xffff R1(config)#dlsaccess-list 200 per 0x0 0xffffden 0xf0f0 0x0001dlsw remote 2 tcp 180.40.7.129 ls R1(config)#dlsw remote 2 tcp 180.40.7.129 lsap-output-list 200 R1(config)#^Z R1# *Mar 1 00:25:04.418: %SYS-5-CONFIG_I: Configured from console by console R1# R1#dlsw remote 2 tcp 180.40.7.129 lsap-output-list 200                                                   sh run i | i dlsw dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 2 tcp 180.40.7.129 lsap-output-list 200 dlsw remote-peer 1 frame-relay interface Serial0/0 102 dlsw bridge-group 1 dlsw bridge-group 2 R1#sh run | i access access-list 200 deny 0xF0F0 0x0001 access-list 200 permit 0x0000 0xFFFF R1#sh run int e 0/1 Building configuration... Current configuration : 83 bytes ! interface Ethernet0/1 no ip address shutdown half-duplex bridge-group 2 end R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | i dlsw dlsw local-peer peer-id 180.40.7.129 group 2 promiscuous dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 1 fst 200.1.1.2 dlsw remote-peer 2 tcp 17.57.100.1 lsap-output-list 200 dlsw bridge-group 1 dlsw bridge-group 2 R3#sh run | i access access-list 200 deny 0xF0F0 0x0001 access-list 200 permit 0x0000 0xFFFF R3#sh run int fa 0/0 Building configuration... Current configuration : 89 bytes ! interface FastEthernet0/0 no ip address duplex auto speed auto bridge-group 2 end R3# R3# RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#net R1(config)#netbios ? access-list Define NETBIOS station access list name-cache Set name cache parameters R1(config)#netbios acc R1(config)#netbios access-list ? bytes NETBIOS byte offset access list filter-name-recognized Filter the Name Recognized frame host Assign name of access list to NETBIOS station[s] R1(config)#netbios access-list ho ? WORD Access-list name R1(config)#netbios access-list ho Prob10 ? deny Specify packets to reject permit Specify packets to forward R1(config)#netbios access-list ho Prob10 den ? WORD Pattern for a set of NETBIOS station names R1(config)#netbios access-list ho Prob10 den GK? WORD R1(config)#netbios access-list ho Prob10 den GK? WORD R1(config)#netbios access-list ho Prob10 den GK? WORD R1(config)#netbios access-list ho Prob10 den GK? WORD R1(config)#netbios access-list ho Prob10 den GK? ? WORD R1(config)#netbios access-list ho Prob10 den GK?CCIE ? R1(config)#netbios access-list ho Prob10 den GK?CCIE   R1(config)#^C netbios access-list ho Prob10 den GK?CCIE           per R1(config)#netbios access-list ho Prob10 permit * R1(config)#dlsw      sh    do sh run | i dlsw dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 2 tcp 180.40.7.129 lsap-output-list 200 dlsw remote-peer 1 frame-relay interface Serial0/0 102 dlsw bridge-group 1 dlsw bridge-group 2 R1(config)#dlsw remote-peer 1 frame-relay interface Serial0/0 102 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets pass-thru Remote peer is capable of locally acknowledging DLC sessions passive Local peer will not initiate this remote peer connection rsvp Configure reservations using RSVP R1(config)#dlsw remote-peer 1 frame-relay interface Serial0/0 102 host   R1(config)#$-peer 1 frame-relay interface Serial0/0 102 host-netbios-out ? WORD Name of previously defined netbios host access list filter R1(config)#$-peer 1 frame-relay interface Serial0/0 102 host-netbios-out Probame-relay interface Serial0/0 102 host-netbios-out Prob1 0 ? backup-peer Configure as a backup to an existing remote peer bytes-netbios-out Configure netbios bytes output filtering for this peer circuit-weight Configure circuit-weight for this peer cluster Override cluster-id of remote peer cost Cost to Reach this Remote Peer dest-mac Exclusive destination mac-addr for remote peer dmac-output-list Filter output destination mac addresses host-netbios-out Configure netbios host output filtering for this peer keepalive Set keepalive interval for this remote peer lf Largest Frame Size for this Remote Peer lsap-output-list Filter output IEEE 802.5 encapsulated packets pass-thru Remote peer is capable of locally acknowledging DLC sessions passive Local peer will not initiate this remote peer connection rsvp Configure reservations using RSVP R1(config)#$ame-relay interface Serial0/0 102 host-netbios-out Prob10 R1(config)#^Z R1#sh run *Mar 1 00:30:59.904: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | i dlsw dlsw local-peer peer-id 17.57.100.1 group 2 cost 2 dlsw bgroup-list 1 bgroups 1 dlsw bgroup-list 2 bgroups 2 dlsw remote-peer 2 tcp 180.40.7.129 lsap-output-list 200 dlsw remote-peer 1 frame-relay interface Serial0/0 102 host-netbios-out Prob10 dlsw bridge-group 1 dlsw bridge-group 2 R1#sh run | i networ   bios acces netbios access-list host Prob10 deny GK?CCIE netbios access-list host Prob10 permit * R1# R1#