=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2005.11.09 08:31:57 =~=~=~=~=~=~=~=~=~=~=~= config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa0/0 1 R7(config-if)#stand R7(config-if)#standby ? <0-255> group number authentication Authentication delay HSRP initialisation delay ip Enable HSRP and set the virtual IP address mac-address Virtual MAC address name Redundancy name string preempt Overthrow lower priority Active routers priority Priority level redirects Configure sending of ICMP Redirect messages with an HSRP virtual IP address as the gateway IP address timers Hello and hold timers track Priority tracking use-bia HSRP uses interface's burned in address R7(config-if)#standby 71 ip 180.40.7.132 ? secondary Make this IP address a secondary virtual IP address R7(config-if)#standby 71 ip 180.40.7.132 R7(config-if)#do sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 - 0013.60e3.f021 ARPA FastEthernet0/1 Internet 180.40.7.130 41 0002.4bcb.56e0 ARPA FastEthernet0/1 Internet 180.40.7.129 41 0013.7f15.f280 ARPA FastEthernet0/1 Internet 208.28.1.1 - 0013.60e3.f020 ARPA FastEthernet0/0 Internet 208.28.1.2 41 0013.80cf.ce00 ARPA FastEthernet0/0 R7(config-if)#do sh standay sh standay ^ % Invalid input detected at '^' marker. R7(config-if)#do sh standay   FastEthernet0/1 - Group 71 State is Active 2 state changes, last state change 00:00:01 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac47 Local virtual MAC address is 0000.0c07.ac47 (default) Hello time 3 sec, hold time 10 sec Next hello sent in 1.365 secs Preemption disabled Active router is local Standby router is unknown Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/1-71" (default) R7(config-if)# *Mar 2 00:37:54.950: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Standby -> Active R7(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/90  0 R3(config-if)#stand 71 180.40.7.132 ^ % Invalid input detected at '^' marker. R3(config-if)# R3(config-if)#stand 71 180.40.7.132 i180.40.7.132p180.40.7.132 180.40.7.132 R3(config-if)#stand 71    pri R3(config-if)#stand priority 12 10 priority 1107 priority 1101 priority 110 R3(config-if)#stand R3(config-if)#standby 71 prw e R3(config-if)#standby 71 preempt R3(config-if)# *Mar 2 00:44:23.443: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Active R3(config-if)# RACK14AS>7 [Resuming connection 7 to r7 ... ] *Mar 2 00:44 R7(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#stan R3(config-if)#standby 71 tr R3(config-if)#standby 71 track ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-FrameRelay Virtual Frame Relay interface Virtual-TokenRing Virtual TokenRing R3(config-if)#standby 71 track >\  ser 1/2 ? <1-255> Decrement value R3(config-if)#standby 71 track ser 1/2 11 R3(config-if)#do sh stand FastEthernet0/0 - Group 71 State is Active 2 state changes, last state change 00:02:15 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac47 Local virtual MAC address is 0000.0c07.ac47 (default) Hello time 3 sec, hold time 10 sec Next hello sent in 2.171 secs Preemption enabled Active router is local Standby router is 180.40.7.131, priority 100 (expires in 7.163 sec) Priority 110 (configured 110) Track interface Serial1/2 state Up decrement 11 IP redundancy name is "hsrp-Fa0/0-71" (default) R3(config-if)#q do sh stand bri R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 110 P Active local 180.40.7.131 180.40.7.132 R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#int s 1/2 R3(config-if)#shut R3(config-if)# *Mar 2 00:46:54.391: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)#shut *Mar 2 00:46:56.390: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 2 00:46:57.391: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#shutint s 1/2do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 99 P Active local 180.40.7.131 180.40.7.132 R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/1 71 100 Standby 180.40.7.129 local 180.40.7.132 R7(config-if)#do sh stand brie =     FastEthernet0/1 - Group 71 State is Standby 4 state changes, last state change 00:02:58 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac47 Local virtual MAC address is 0000.0c07.ac47 (default) Hello time 3 sec, hold time 10 sec Next hello sent in 1.245 secs Preemption disabled Active router is 180.40.7.129, priority 99 (expires in 7.243 sec) Standby router is local Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/1-71" (default) R7(config-if)# R7(config-if)# R7(config-if)#st R7(config-if)#standby 71 pre R7(config-if)# *Mar 2 00:48:22.142: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Standby -> Active R7(config-if)#^Z R7# *Mar 2 00:48:45.605: %SYS-5-CONFIG_I: Configured from console by console R7# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Ma R3(config-if)#no shut R3(config-if)#^Z R3# *Mar 2 00:48:59.167: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 2 00:49:00.633: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 2 00:49:01.635: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3# *Mar 2 00:49:02.545: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Active R3# *Mar 2 00:49:10.758: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from LOADING to FULL, Loading Done R3# R3# R3# R3#sh run int fa 0/0 Building configuration... Current configuration : 230 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 71 ip 180.40.7.132 standby 71 priority 110 standby 71 preempt standby 71 track Serial1/2 11 end R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh run int fa 0/1 Building configuration... Current configuration : 176 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output Prob6 speed auto half-duplex standby 71 ip 180.40.7.132 standby 71 preempt end R7# R7# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#dhcp ? % Unrecognized command R3(config)#dhcp      ip dhcp ? aaa Configure aaa attributes binding DHCP address bindings bootp BOOTP specific configuration conflict DHCP address conflict parameters database Configure DHCP database agents excluded-address Prevent DHCP from assigning certain addresses limited-broadcast-address Use all 1's broadcast address ping Specify ping parameters used by DHCP pool Configure DHCP address pools relay DHCP relay agent parameters smart-relay Enable Smart Relay feature R3(config)#ip dhcp pool ? WORD Pool name R3(config)#ip dhcp pool Prob11 ? R3(config)#ip dhcp pool Prob11 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#newo R3(dhcp-config)#newo  tw R3(dhcp-config)#network ? A.B.C.D Network number in dotted-decimal notation R3(dhcp-config)#network 180.l40.7.128 ? % Unrecognized command R3(dhcp-config)#network 180.l40.7.128 .l40.7.128 40.7.128 ? /nn or A.B.C.D Network mask or prefix length R3(dhcp-config)#network 180.40.7.128 /27 ? R3(dhcp-config)#network 180.40.7.128 /27 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#def R3(dhcp-config)#default-router 180.40.7.132 ? Hostname or A.B.C.D Router's name or IP address R3(dhcp-config)#default-router 180.40.7.132 R3(dhcp-config)#dn R3(dhcp-config)#dns-server ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#dns-server 20.   207 8.28.1.82 R3(dhcp-config)#dns-server 208.28.1.82 ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#dns-server 208.28.1.82                        dom, R3(dhcp-config)#dom,  R3(dhcp-config)#domain-name ? WORD Domain name R3(dhcp-config)#domain-name ccci  iestudent.com R3(dhcp-config)#tfp R3(dhcp-config)#tfp? % Unrecognized command R3(dhcp-config)#tfp   ? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   utilization Configure various utilization parameters vrf Associate this pool with a VRF R3(dhcp-config)#op R3(dhcp-config)#option ? <0-254> DHCP option code R3(dhcp-config)#option 150 ? ascii Data is an NVT ASCII string hex Data is a hexadecimal string instance Specify the option instance ip Data is one or more IP addresses R3(dhcp-config)#option 150 ip ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#option 150 ip 20.20.20.20 R3(dhcp-config)#exit R3(config)#ip dh R3(config)#ip dhcp e R3(config)#ip dhcp excluded-address ? A.B.C.D Low IP address R3(config)#ip dhcp excluded-address 180.40.7.129 ? A.B.C.D High IP address R3(config)#ip dhcp excluded-address 180.40.7.129 180.40.7.132 R3(config)#^Z R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#ip add ? A.B.C.D IP address dhcp IP Address negotiated via DHCP pool IP Address autoconfigured from a local DHCP pool R4(config-if)#ip add dh R4(config-if)#ip add dhcp ? client-id Specify client-id to use hostname Specify value for hostname option R4(config-if)#ip add dhcp R4(config-if)#^Z R4# *Mar 2 01:07:51.689: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 01:07:51.689: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4# *Mar 2 01:07:52.913: %SYS-5-CONFIG_I: Configured from console by console R4#Interface FastEthernet0/0 assigned DHCP address 180.40.7.133, mask 255.255.255.224 sh ip        R4# R4# R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.133 YES DHCP up up ATM1/0 unassigned YES unset administratively down down Virtual-Access1 unassigned YES unset up up Loopback0 100.1.1.1 YES manual up up R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] * R3#sh un     run |  run | run |  *Mar 2 01:06:40.178: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3#sh run | b dhcp ip dhcp excluded-address 180.40.7.129 180.40.7.132 ! ip dhcp pool Prob11 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 dns-server 208.28.1.82 domain-name cciestudent.com option 150 ip 20.20.20.20 ! ip cef ip audit notify log ip audit po max-events 100 ! mpls ldp logging neighbor-changes ! ! ! ! ! ! ! ! ! --More--   R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh run int fa 0/0 Building configuration... Current configuration : 75 bytes ! interface FastEthernet0/0 ip address dhcp duplex auto speed auto end R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.133 YES DHCP up up ATM1/0 unassigned YES unset administratively down down Virtual-Access1 unassigned YES unset up up Loopback0 100.1.1.1 YES manual up up R4# R4# RACK14AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh run int fa 0/1 Building configuration... Current configuration : 94 bytes ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 duplex auto speed auto end R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa 0/1 R2(config-if)#ip he R2(config-if)#ip help R2(config-if)#ip helper-address ? A.B.C.D IP destination address global Helper-address is global vrf VRF name for helper-address (if different from interface VRF) R2(config-if)#ip helper-address 208.28.1.99 R2(config-if)#exit R2(config)#ip fo R2(config)#ip forward-protocol ? nd Sun's Network Disk protocol sdns Network Security Protocol spanning-tree Use transparent bridging to flood UDP broadcasts turbo-flood Fast flooding of UDP broadcasts udp Packets to a specific UDP port R2(config)#ip forward-protocol udp ? <0-65535> Port number biff Biff (mail notification, comsat, 512) bootpc Bootstrap Protocol (BOOTP) client (68) bootps Bootstrap Protocol (BOOTP) server (67) discard Discard (9) dnsix DNSIX security protocol auditing (195) domain Domain Name Service (DNS, 53) echo Echo (7) isakmp Internet Security Association and Key Management Protocol (500) mobile-ip Mobile IP registration (434) nameserver IEN116 name service (obsolete, 42) netbios-dgm NetBios datagram service (138) netbios-ns NetBios name service (137) netbios-ss NetBios session service (139) non500-isakmp Internet Security Association and Key Management Protocol (4500) ntp Network Time Protocol (123) pim-auto-rp PIM Auto-RP (496) rip Routing Information Protocol (router, in.routed, 520) snmp Simple Network Management Protocol (161) snmptrap SNMP Traps (162) --More--   R2(config)#ip forward-protocol udp R2(config)#netbios-dgm           ip forward-protocol udp netbios-dgmnip forward-protocol udp netbios-dgmoip forward-protocol udp netbios-dgm ip forward-protocol udp netbios-dgm R2(config)#do sh run Building configuration... Current configuration : 2113 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R2 ! logging queue-limit 100 ! memory-size iomem 10 ip subnet-zero ! ! no ip domain lookup ! ip audit notify log ip audit po max-events 100 mpls ldp logging neighbor-changes frame-relay de-list 1 protocol ip list 100 ! --More--  ! ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! interface FastEthernet0/0 no ip address shutdown --More--   duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 203 --More--  ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob4 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clockrate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown --More--  ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless no ip forward-protocol udp netbios-dgm ! ! --More--  ! ! map-class frame-relay Prob4 frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn access-list 100 deny ospf any any access-list 100 permit ip any any ! ! call rsvp-sync ! ! mgcp profile default ! ! ! dial-peer cor custom ! ! ! ! --More--   R2(config)#^Z R2# *Mar 2 01:14:48.996: %SYS-5-CONFIG_I: Configured from console by console R2#sh run int fa 0/1 Building configuration... Current configuration : 125 bytes ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto end R2# R2# RACK14AS>7 [Resuming connection 7 to r7 ... ] *M R7#sh run Building configuration... Current configuration : 2339 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R7 ! logging queue-limit 100 ! ip subnet-zero ! ! no ip domain lookup ! ip audit notify log ip audit po max-events 100 mpls ldp logging neighbor-changes ! ! ! --More--   R7#sh run  int % Incomplete command. R7#s 0/0.2 show 0/0.2 ^ % Invalid input detected at '^' marker. R7#s 0/0.2 0/0.2r 0/0.2u 0/0.2n 0/0.2 show run 0/0.2 ^ % Invalid input detected at '^' marker. R7#s run 0/0.2s0/0.2 show run s0/0.2 ^ % Invalid input detected at '^' marker. R7#s run s0/0.2 0/0.2 show run s 0/0.2 ^ % Invalid input detected at '^' marker. R7#sh run s 0 1/0.2 ^ % Invalid input detected at '^' marker. R7#sh urn ^ % Invalid input detected at '^' marker. R7#sh run Building configuration... Current configuration : 2339 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R7 ! logging queue-limit 100 ! ip subnet-zero ! ! no ip domain lookup ! ip audit notify log ip audit po max-events 100 mpls ldp logging neighbor-changes ! ! ! --More--  ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! class-map match-all S5Other match access-group 101 class-map match-all S5Telnet match access-group 100 ! ! policy-map Prob6 --More--   class S5Telnet bandwidth 1000 class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output Prob6 speed auto --More--   half-duplex standby 71 ip 180.40.7.132 standby 71 preempt ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0.2 R7(config-subif)#fram R7(config-subif)#frame-relay in R7(config-subif)#frame-relay int R7(config-subif)#frame-relay interface-dlci 702 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R7(config-subif)#frame-relay interface-dlci 702 pro R7(config-subif)#frame-relay interface-dlci 702 protocol ? A.B.C.D Protocol specific address ip IP R7(config-subif)#frame-relay interface-dlci 702 protocol ip ? A.B.C.D Protocol specific address R7(config-subif)#frame-relay interface-dlci 702 protocol ip 180.40.7.162 %PVC is already defined R7(config-fr-dlci)#do sh run int s 1/0.2 Building configuration... Current configuration : 208 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 end R7(config-fr-dlci)#exit R7(config-subif)#no frame-relay interface-dlci 702 R7(config-subif)# *Mar 2 01:18:47.943: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-subif)#no frame-relay interface-dlci 702exit do sh run int s 1/0.2frame-relay interface-dlci 702 protocol ip 180.40.7.162 R7(config-fr-dlci)#^Z R7# *Mar 2 01:18:54.222: %SYS-5-CONFIG_I: Configured from console by console R7#sh ur  run int s 1/0.2 Building configuration... Current configuration : 230 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 end R7# *Mar 2 01:19:06.802: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0.2 R7(config-subif)#ip helper-address 208.28.1.99 R7(config-subif)#^Z R7#sh run in *Mar 2 01:19:36.884: %SYS-5-CONFIG_I: Configured from console by console R7#sh run int s 1/0.2 Building configuration... Current configuration : 261 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 end R7# R7#sh run int fa 0/1 Building configuration... Current configuration : 176 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output Prob6 speed auto half-duplex standby 71 ip 180.40.7.132 standby 71 preempt end R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#no standby 71 ip 180.40.7.132 R7(config-if)#no standby 71 preempt R7(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#i int fa 0./  /0 R3(config-if)#no standby 71 preempt R3(config-if)#no standby 71 ip 180.40.7.132 R3(config-if)#no s *Mar 2 01:25:14.417: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Active -> Disabled R3(config-if)#no stan 71 pre R3(config-if)#do sh run int fa 0/0 Building configuration... Current configuration : 182 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 71 priority 110 standby 71 track Serial1/2 11 end R3(config-if)#no standby 71 priority 110 R3(config-if)#no standby 71 track Serial1/2 11 R3(config-if)#exit R3(config)#tr R3(config)#tra R3(config)#tra? track translate translation-rule R3(config)#track ? <1-500> Tracked object resolution Tracking resolution parameters timer Polling interval timers R3(config)#track 1 ? interface Select an interface to track ip IP protocol R3(config)#track 1 ip ? route IP route R3(config)#track 1 ip routre    e ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R3(config)#track 1 ip route 20.10.1.0 ? A.B.C.D {/nn || A.B.C.D} IP prefix and prefix mask R3(config)#track 1 ip route 20.10.1.0 /24 ? % Unrecognized command R3(config)#track 1 ip route 20.10.1.0 /24      /24 ? metric Route metric reachability Route reachability state R3(config)#track 1 ip route 20.10.1.0/24 re R3(config)#track 1 ip route 20.10.1.0/24 reachability ? R3(config)#track 1 ip route 20.10.1.0/24 reachability R3(config-track)#? Tracking instance configuration commands: default Set a command to its defaults delay Tracking delay exit Exit from tracking configuration mode ip Tracking IP configuration subcommands no Negate a command or set its defaults R3(config-track)#int fa 0/0 R3(config-if)#gl R3(config-if)#glbp ? <0-1023> Group number R3(config-if)#glbp 1 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R3(config-if)#glbp 1 ip ? A.B.C.D Virtual IP address R3(config-if)#glbp 1 ip 180.40.7.132 ? secondary Make this IP address a secondary address R3(config-if)#glbp 1 ip 180.40.7.132 R3(config-if)#gl R3(config-if)#glbp ? <0-1023> Group number R3(config-if)#glbp 1 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R3(config-if)#glbp 1 *Mar 2 01:28:18.775: %GLBP-6-STATECHANGE: FastEthernet0/0 Grp 1 state Standby -> Active R3(config-if)#glbp 1 *Mar 2 01:28:28.776: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 1 Fwd 1 state Listen -> Active R3(config-if)#glbp 1 wei R3(config-if)#glbp 1 weighting ? <1-254> Weighting maximum value track Interface tracking R3(config-if)#glbp 1 weighting tr R3(config-if)#glbp 1 weighting track       tr r R3(config-if)#glbp 1 weighting track ? <1-500> Tracked object R3(config-if)#glbp 1 weighting track 1 ? decrement Weighting decrement R3(config-if)#glbp 1 weighting track 1 de R3(config-if)#glbp 1 weighting track 1 decrement ? <1-255> Decrement value R3(config-if)#glbp 1 weighting track 1 decrement 1                   ? <1-254> Weighting maximum value track Interface tracking R3(config-if)#glbp 1 weighting 100 ? lower Weighting lower threshold upper Weighting upper threshold R3(config-if)#glbp 1 weighting 100 lo R3(config-if)#glbp 1 weighting 100 lower 50 ? upper Weighting upper threshold R3(config-if)#glbp 1 weighting 100 lower 50 up R3(config-if)#glbp 1 weighting 100 lower 50 upper 99                       tr R3(config-if)#glbp 1 weighting track 1 de R3(config-if)#glbp 1 weighting track 1 decrement 1 R3(config-if)#^Z R3#sh run | *Mar 2 01:32:43.770: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b track track 1 ip route 20.10.1.0 255.255.255.0 reachability mpls ldp logging neighbor-changes ! ! ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! class-map match-all telnet match protocol telnet --More--   class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 1 ! --More--   R3# R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#exit R7(config)# R7(config)#track 1 ip route 20.10.1.0 255.255.255.0 reachability R7(config-track)#!int fa 0/1 R7(config-track)#!int fa 0/1!int fa 0/1  R7(config-if)#glbp 1 ip 180.40.7.132 R7(config-if)# glbp 1 weighting track 1 decrement 1 R7(config-if)#^Z R7# *Mar 2 01:33:48.083: %SYS-5-CONFIG_I: Configured from console by console R7#sh *Mar 2 01:34:08.348: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 1 Fwd 2 state Listen -> Active R7#sh gl FastEthernet0/1 - Group 1 State is Speak Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 0.359 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.129, priority 100 (expires in 7.528 sec) Standby is unknown Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 1 state Up decrement 1 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.0101 (learnt) Owner ID is 0013.7f15.f280 Time to live: 14397.524 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 100 (expires in 7.524 sec) Forwarder 2 State is Active --More--   R7# sh gl ? BVI Bridge-Group Virtual Interface FastEthernet FastEthernet IEEE 802.3 Port-channel Ethernet Channel of interfaces active Groups in active state brief Brief output capability GLBP capability disabled Groups in disabled state init Groups in init state listen Groups in listen state standby Groups in standby or speak states | Output modifiers R7#sh gl brie Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Standby 180.40.7.132 180.40.7.129 local Fa0/1 1 1 7 Listen 0007.b400.0101 180.40.7.129 - Fa0/1 1 2 7 Active 0007.b400.0102 local - R7# R7# R7# R7# R7# R7# R7# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.        sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 29 0013.60e3.f021 ARPA FastEthernet0/0 Internet 180.40.7.129 29 0013.7f15.f280 ARPA FastEthernet0/0 Internet 180.40.7.133 - 0002.4bcb.56e0 ARPA FastEthernet0/0 R4#telnet 20.10.1.1 Trying 20.10.1.1 ... Open R2#q [Connection to 20.10.1.1 closed by foreign host] R4#telnet 20.10.1.1sh arp  Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 29 0013.60e3.f021 ARPA FastEthernet0/0 Internet 180.40.7.129 29 0013.7f15.f280 ARPA FastEthernet0/0 Internet 180.40.7.133 - 0002.4bcb.56e0 ARPA FastEthernet0/0 R4#ping      telnet 180.40.7.132 Trying 180.40.7.132 ... Open R3#q [Connection to 180.40.7.132 closed by foreign host] R4#sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 30 0013.60e3.f021 ARPA FastEthernet0/0 Internet 180.40.7.129 29 0013.7f15.f280 ARPA FastEthernet0/0 Internet 180.40.7.133 - 0002.4bcb.56e0 ARPA FastEthernet0/0 Internet 180.40.7.132 0 0007.b400.0101 ARPA FastEthernet0/0 R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route 20./ 10.1.0 Routing entry for 20.10.1.0/24 Known via "ospf 1", distance 110, metric 782, type intra area Last update from 180.40.7.67 on Serial1/0, 00:17:51 ago Routing Descriptor Blocks: * 180.40.7.67, from 180.40.7.162, 00:17:51 ago, via Serial1/0 Route metric is 782, traffic share count is 1 180.40.7.2, from 180.40.7.162, 00:17:51 ago, via Serial1/2 Route metric is 782, traffic share count is 1 R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.133, 00:19:53, FastEthernet0/1 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.162, 00:19:53, Serial1/0.2 O 20.10.1.0 [110/782] via 180.40.7.162, 00:19:53, Serial1/0.2 C 208.28.1.0/24 is directly connected, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/1 O 180.40.7.162/32 [110/781] via 180.40.7.162, 00:19:54, Serial1/0.2 C 180.40.7.160/27 is directly connected, Serial1/0.2 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:19:54, FastEthernet0/1 O 180.40.7.67/32 [110/781] via 180.40.7.162, 00:19:54, Serial1/0.2 O 180.40.7.66/32 [110/1] via 180.40.7.129, 00:19:54, FastEthernet0/1 --More--   R7# RACK14AS>2 [Resuming connection 2 to r2 ... ] *M R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.2 R2(config-subif)#shut R2(config-subif)# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip    glbp bri Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Standby 180.40.7.132 180.40.7.129 local Fa0/1 1 1 7 Listen 0007.b400.0101 180.40.7.129 - Fa0/1 1 2 7 Active 0007.b400.0102 local - R7#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.133, 00:00:12, FastEthernet0/1 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 00:00:12, FastEthernet0/1 O 20.10.1.0 [110/783] via 180.40.7.129, 00:00:12, FastEthernet0/1 C 208.28.1.0/24 is directly connected, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/1 C 180.40.7.160/27 is directly connected, Serial1/0.2 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:13, FastEthernet0/1 O 180.40.7.67/32 [110/782] via 180.40.7.129, 00:00:13, FastEthernet0/1 O 180.40.7.66/32 [110/1] via 180.40.7.129, 00:00:13, FastEthernet0/1 C 180.40.7.64/27 is directly connected, Serial1/0.1 R7# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Ma R2(config-subif)#no shutt  R2(config-subif)#int fa 0/1 R2(config-if)#shut R2(config-if)# *Mar 2 01:40:01.247: %OSPF-5-ADJCHG: Process 1, Nbr 20.10.2.1 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh glbp FastEthernet0/0 - Group 1 State is Active 2 state changes, last state change 00:11:56 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 1.153 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.131, priority 100 (expires in 9.047 sec) Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 1 state Up decrement 1 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:11:46 MAC address is 0007.b400.0101 (default) Owner ID is 0013.7f15.f280 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 --More--   R3#sh glbp bri Interface Grp Fwd Pri State Address Active router Standby router Fa0/0 1 - 100 Active 180.40.7.132 local 180.40.7.131 Fa0/0 1 1 7 Active 0007.b400.0101 local - Fa0/0 1 2 7 Listen 0007.b400.0102 180.40.7.131 - R3#sh glbp bri     FastEthernet0/0 - Group 1 State is Active 2 state changes, last state change 00:12:07 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 2.071 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.131, priority 100 (expires in 9.964 sec) Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 1 state Up decrement 1 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:11:57 MAC address is 0007.b400.0101 (default) Owner ID is 0013.7f15.f280 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 --More--   Arp replies sent: 1 --More--   Forwarder 2 --More--   State is Listen --More--   MAC address is 0007.b400.0102 (learnt) --More--   Owner ID is 0013.60e3.f021 --More--   Redirection enabled, 597.728 sec remaining (maximum 600 sec) --More--   Time to live: 14397.564 sec (maximum 14400 sec) --More--   Preemption enabled, min delay 30 sec --More--   Active is 180.40.7.131 (primary), weighting 99 (expires in 9.159 sec) R3#sh glbp FastEthernet0/0 - Group 1 State is Active 2 state changes, last state change 00:12:34 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 1.698 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.131, priority 100 (expires in 9.588 sec) Priority 100 (default) Weighting 99 (default 100), thresholds: lower 1, upper 100 Track object 1 state Down decrement 1 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:12:24 MAC address is 0007.b400.0101 (default) Owner ID is 0013.7f15.f280 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 99 --More--   Arp replies sent: 1 Forwarder 2 State is Listen MAC address is 0007.b400.0102 (learnt) Owner ID is 0013.60e3.f021 Redirection enabled, 598.734 sec remaining (maximum 600 sec) Time to live: 14398.734 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 99 (expires in 8.730 sec) R3#sh glbp FastEthernet0/0 - Group 1 State is Active 2 state changes, last state change 00:13:29 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 1.089 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.131, priority 100 (expires in 8.982 sec) Priority 100 (default) Weighting 99 (default 100), thresholds: lower 1, upper 100 Track object 1 state Down decrement 1 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:13:19 MAC address is 0007.b400.0101 (default) Owner ID is 0013.7f15.f280 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 99 --More--   Arp replies sent: 1 Forwarder 2 State is Listen MAC address is 0007.b400.0102 (learnt) Owner ID is 0013.60e3.f021 Redirection enabled, 598.477 sec remaining (maximum 600 sec) Time to live: 14398.477 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 99 (expires in 8.477 sec) R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#int fa 0/0glbp 1 weighting track 1 decrement 1 100 R3(config-if)#^Z R3# *Mar 2 01:42:08.551: %SYS-5-CONFIG_I: Configured from console by console R3#config tsh glbp  FastEthernet0/0 - Group 1 State is Active 2 state changes, last state change 00:13:54 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 0.107 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.131, priority 100 (expires in 8.001 sec) Priority 100 (default) Weighting 0, low (default 100), thresholds: lower 1, upper 100 Track object 1 state Down decrement 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:13:44 MAC address is 0007.b400.0101 (default) Owner ID is 0013.7f15.f280 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 0 --More--   Arp replies sent: 1 Forwarder 2 State is Listen MAC address is 0007.b400.0102 (learnt) Owner ID is 0013.60e3.f021 Redirection enabled, 599.071 sec remaining (maximum 600 sec) Time to live: 14399.067 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 99 (expires in 9.067 sec) R3#sh glbp bri R3#sh glbp brief Interface Grp Fwd Pri State Address Active router Standby router Fa0/0 1 - 100 Active 180.40.7.132 local 180.40.7.131 Fa0/0 1 1 7 Active 0007.b400.0101 local - Fa0/0 1 2 7 Listen 0007.b400.0102 180.40.7.131 - R3# *Mar 2 01:42:40.063: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 1 Fwd 1 state Active -> Listen R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#gl R3(config-if)#glbp 1 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R3(config-if)#glbp 1 tim R3(config-if)#glbp 1 timers ? <1-60> Hello interval in seconds msec Specify hello interval in milliseconds redirect Specify time-out values for failed forwarders R3(config-if)#glbp 1 timers re R3(config-if)#glbp 1 timers redirect ? <0-3600> Interval in seconds to redirect to failed forwarders R3(config-if)#glbp 1 timers redirect 1 % Incomplete command. R3(config-if)#glbp 1 timers redirect 1 ? <601-64800> Time-out interval in seconds for failed forwarders R3(config-if)#glbp 1 timers redirect 1                          ^Z R3#sh *Mar 2 01:44:01.484: %SYS-5-CONFIG_I: Configured from console by console R3#sh glb FastEthernet0/0 - Group 1 State is Active 2 state changes, last state change 00:15:45 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 2.856 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.131, priority 100 (expires in 7.749 sec) Priority 100 (default) Weighting 0, low (default 100), thresholds: lower 1, upper 100 Track object 1 state Down decrement 100 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen 2 state changes, last state change 00:01:24 MAC address is 0007.b400.0101 (default) Owner ID is 0013.7f15.f280 Redirection enabled Preemption enabled, min delay 30 sec Active is 180.40.7.131 (secondary), weighting 99 (expires in 7.745 sec) --More--   Arp replies sent: 1 Forwarder 2 State is Listen MAC address is 0007.b400.0102 (learnt) Owner ID is 0013.60e3.f021 Redirection enabled, 598.298 sec remaining (maximum 600 sec) Time to live: 14398.298 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 99 (expires in 8.298 sec) R3#sh glb FastEthernet0/0 - Group 1 State is Active 2 state changes, last state change 00:16:33 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 2.760 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.131, priority 100 (expires in 7.652 sec) Priority 100 (default) Weighting 0, low (default 100), thresholds: lower 1, upper 100 Track object 1 state Down decrement 100 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen 2 state changes, last state change 00:02:12 MAC address is 0007.b400.0101 (default) Owner ID is 0013.7f15.f280 Redirection enabled Preemption enabled, min delay 30 sec Active is 180.40.7.131 (secondary), weighting 99 (expires in 7.648 sec) --More--   Arp replies sent: 1 Forwarder 2 State is Listen MAC address is 0007.b400.0102 (learnt) Owner ID is 0013.60e3.f021 Redirection enabled, 599.579 sec remaining (maximum 600 sec) Time to live: 14399.579 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 99 (expires in 9.575 sec) R3#sh run int fa 0/0 Building configuration... Current configuration : 190 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 100 end R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] * R7#sh ru n  n | i class class-map match-all S5Other class-map match-all S5Telnet class S5Telnet class S5Other ip classless map-class frame-relay Prob7 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#class R7(config)#class-map ftp R7(config-cmap)#mat R7(config-cmap)#match pr R7(config-cmap)#match pro R7(config-cmap)#match protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 --More--   custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) --More--   R7(config-cmap)#match protocol ftpo ^ % Invalid input detected at '^' marker. R7(config-cmap)#match protocol ftpo  R7(config-cmap)#exit R7(config)#ip cef R7(config)#class telnet ^ % Invalid input detected at '^' marker. R7(config)#class telnet- telnetm telneta telnetp telnet R7(config-cmap)#mat prot telnet R7(config-cmap)#exit R7(config)#pol R7(config)#policy-map extras ? R7(config)#policy-map extras R7(config-pmap)#class ftp R7(config-pmap-c)#ban R7(config-pmap-c)#bandwidth per R7(config-pmap-c)#bandwidth percent 25 R7(config-pmap-c)#exit R7(config-pmap)#class telnet R7(config-pmap-c)#ban per 25 R7(config-pmap-c)#ecxi    exit R7(config-pmap)#int fa 0/1 R7(config-if)#ser R7(config-if)#service-policy ou extras Policy map Prob6 is already attached R7(config-if)#do sh run int fa 0/1 Building configuration... Current configuration : 190 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output Prob6 speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 1 end R7(config-if)#no service-policy output Prob6 R7(config-if)#no service-policy output Prob6do sh run int fa 0/1 service-policy ou extras R7(config-if)#^Z R7#sh run | *Mar 2 01:50:00.605: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b class class-map match-all telnet match protocol telnet class-map match-all S5Other match access-group 101 class-map match-all S5Telnet match access-group 100 class-map match-all ftp match protocol ftp ! ! policy-map extras class ftp bandwidth percent 25 class telnet bandwidth percent 25 policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! --More--  ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output extras speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 1 ! interface Serial1/0 no ip address encapsulation frame-relay --More--   R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#do sh access-list Extended IP access list 100 10 permit tcp host 208.28.1.2 any eq telnet Extended IP access list 101 10 permit ip host 208.28.1.2 any R7(config)#access-list 102 per tcp ? A.B.C.D Source address any Any source host host A single source host R7(config)#access-list 102 per tcp any host 87.23.11.123 eq ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   pop2 Post Office Protocol v2 (109) pop3 Post Office Protocol v3 (110) smtp Simple Mail Transport Protocol (25) sunrpc Sun Remote Procedure Call (111) syslog Syslog (514) tacacs TAC Access Control System (49) talk Talk (517) telnet Telnet (23) time Time (37) uucp Unix-to-Unix Copy Program (540) whois Nicname (43) www World Wide Web (HTTP, 80) R7(config)#access-list 102 per tcp any host 87.23.11.123 eq 1  RACK14AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#access-list 199 tcp per any any eq ? % Unrecognized command R1(config)#access-list 199 tcp per any any eq  any any eq  any any eq  any any eq any any eq p tcp any any eq e tcp any any eq  tcp any any eq r tcp any any eq r tcp any any eq  per tcp any any eq per tcp any any eq ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   pop2 Post Office Protocol v2 (109) pop3 Post Office Protocol v3 (110) smtp Simple Mail Transport Protocol (25) sunrpc Sun Remote Procedure Call (111) syslog Syslog (514) tacacs TAC Access Control System (49) talk Talk (517) telnet Telnet (23) time Time (37) uucp Unix-to-Unix Copy Program (540) whois Nicname (43) www World Wide Web (HTTP, 80) R1(config)#access-list 199 per tcp any any eq                                    ^Z R1# *Mar 2 01:57:33.027: %SYS-5-CONFIG_I: Configured from console by console R1# RACK14AS>7 [Resuming connection 7 to r7 ... ] % Incomplete command. R7(config)#access-list 102 per tcp any host 87.23.11.123 eq 1433 R7(config)#access-list 102 per tcp any host 87.23.11.123 eq 1433 4 R7(config)#poli R7(config)#policy-map extras R7(config-pmap)#exit R7(config)#class-map % Incomplete command. R7(config)#class-map sql R7(config-cmap)#match pro R7(config-cmap)#match protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 --More--   custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) --More--   ipsec IP Security Protocol (ESP/AH) ipv6 IPV6 ipx Novell IPX irc Internet Relay Chat kazaa2 Kazaa Version 2 kerberos Kerberos l2tp L2F/L2TP tunnel ldap Lightweight Directory Access Protocol llc2 llc2 napster Napster Traffic netbios NetBIOS netshow Microsoft Netshow nfs Network File System nntp Network News Transfer Protocol notes Lotus Notes(R) novadigm Novadigm EDM ntp Network Time Protocol pad PAD links pcanywhere Symantec pcANYWHERE pop3 Post Office Protocol pppoe PPP over Ethernet pptp Point-to-Point Tunneling Protocol printer print spooler/lpd --More--   qllc qllc protocol rcmd BSD r-commands (rsh, rlogin, rexec) realaudio Real Audio streaming protocol rip Routing Information Protocol rsrb Remote Source-Route Bridging rsvp Resource Reservation Protocol rtp Real Time Protocol rtspplayer RTSP players streaming protocol secure-ftp FTP over TLS/SSL secure-http Secured HTTP secure-imap Internet Message Access Protocol over TLS/SSL secure-irc Internet Relay Chat over TLS/SSL secure-ldap Lightweight Directory Access Protocol over TLS/SSL secure-nntp Network News Transfer Protocol over TLS/SSL secure-pop3 Post Office Protocol over TLS/SSL secure-telnet Telnet over TLS/SSL smtp Simple Mail Transfer Protocol snapshot Snapshot routing support snmp Simple Network Mangement Protocol socks SOCKS sqlnet SQL*NET for Oracle sqlserver MS SQL Server ssh Secured Shell --More--   R7(config-cmap)#match protocol sql R7(config-cmap)#match protocol sqls R7(config-cmap)#match protocol sqlserver ? R7(config-cmap)#match protocol sqlserver           IP  ? R7(config-cmap)#match protocol IP             acc R7(config-cmap)#match access-group 102 R7(config-cmap)#exit R7(config)#pol R7(config)#policy-map extras R7(config-pmap)#class R7(config-pmap)#class sql R7(config-pmap-c)#pr R7(config-pmap-c)#priority ? <8-2000000> Kilo Bits per second percent % of total bandwidth R7(config-pmap-c)#priority 56 ? <32-2000000> Burst in bytes R7(config-pmap-c)#priority 56 128 ? R7(config-pmap-c)#priority 56 128   R7(config-pmap-c)#^Z R7#sh *Mar 2 02:05:31.888: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b class class-map match-all telnet match protocol telnet class-map match-all S5Other match access-group 101 class-map match-all S5Telnet match access-group 100 class-map match-all ftp match protocol ftp class-map match-all sql match access-group 102 ! ! policy-map extras class ftp bandwidth percent 25 class telnet bandwidth percent 25 class sql priority 56 128 policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other --More--   police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output extras speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 1 --More--  ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address --More--   shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 --More--   log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless ! ! ! ! map-class frame-relay Prob7 frame-relay priority-group 1 access-list 100 permit tcp host 208.28.1.2 any eq telnet access-list 101 permit ip host 208.28.1.2 any access-list 102 permit tcp any host 87.23.11.123 eq 1433 access-list 102 permit tcp any host 87.23.11.123 eq 1434 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! call rsvp-sync ! ! --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#no    pol R7(config)#policy-map extras R7(config-pmap)#policy-map extrasriority 56 128 class sql pclass sqlclass sql nclass sqloclass sql class sql R7(config-pmap)#exit R7(config)#no class sql ^ % Invalid input detected at '^' marker. R7(config)#no class sql- sqlm sqla sqlp sql R7(config)#class  - R7(config)#class-map sql R7(config-cmap)#match pro R7(config-cmap)#match protocol sqls R7(config-cmap)#match hacc R7(config-cmap)#match hacc    acc R7(config-cmap)#match access-group 1 R7(config-cmap)#exit R7(config)#naccess       access  -li R7(config)#access-list 1 per 87.23.11.123 R7(config)#^Z R7#sh run *Mar 2 02:07:57.995: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b class class-map match-all telnet match protocol telnet class-map match-all S5Other match access-group 101 class-map match-all S5Telnet match access-group 100 class-map match-all ftp match protocol ftp class-map match-all sql match protocol sqlserver match access-group 1 ! ! policy-map extras class ftp bandwidth percent 25 class telnet bandwidth percent 25 policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police cir 5000000 --More--   conform-action set-prec-transmit 3 --More--   exceed-action set-prec-transmit 1 --More--  ! --More--  ! --More--   R7#sh tun     run | b access-list access-list 1 permit 87.23.11.123 access-list 100 permit tcp host 208.28.1.2 any eq telnet access-list 101 permit ip host 208.28.1.2 any access-list 102 permit tcp any host 87.23.11.123 eq 1433 access-list 102 permit tcp any host 87.23.11.123 eq 1434 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! call rsvp-sync ! ! mgcp profile default ! ! ! dial-peer cor custom ! ! ! ! ! line con 0 --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pol R7(config)#policy-map extre  ras R7(config-pmap)#class sql R7(config-pmap-c)#pri 56 128 R7(config-pmap-c)#^Z R7#sh *Mar 2 02:11:31.325: %SYS-5-CONFIG_I: Configured from console by console R7#sh pol int fa 0/1 FastEthernet0/1 Service-policy output: extras Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: sql (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 1 Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 736 packets, 83778 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R7#sh queue  ing int fa 0/1 Interface FastEthernet0/1 queueing strategy: fair Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 2/2 (allocated/max allocated) Available Bandwidth 24944 kilobits/sec R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int     pol R7(config)#policy-map extras R7(config-pmap)#class default-class % class map default-class not configured R7(config-pmap)#class default-class      cdefault;defaultldefaultadefaultsdefaultdefault default default default ldefaultadefaultsdefaultsdefault-default R7(config-pmap-c)#fa R7(config-pmap-c)#fair-queue R7(config-pmap-c)#do sh pol int fa 0/1 FastEthernet0/1 Service-policy output: extras Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: sql (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 1 Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 772 packets, 88132 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 256 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-pmap-c)#fai R7(config-pmap-c)#fair-queue ? <16-4096> Number Dynamic Conversation Queues R7(config-pmap-c)#fair-queue 512              do sh queueing int fa 0/1 Interface FastEthernet0/1 queueing strategy: fair Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 2/2 (allocated/max allocated) Available Bandwidth 24944 kilobits/sec R7(config-pmap-c)#fr  R7(config-pmap-c)#fair-queue 512 R7(config-pmap-c)#fair-queue 512do sh queueing int fa 0/1pol int fa 0/1  FastEthernet0/1 Service-policy output: extras Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 521 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 522 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: sql (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 1 Queueing Strict Priority Output Queue: Conversation 520 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 843 packets, 96352 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 512 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-pmap-c)#^Z R7#sh run *Mar 2 02:15:19.856: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b policy policy-map extras class ftp bandwidth percent 25 class telnet bandwidth percent 25 class sql priority 56 128 class class-default fair-queue 512 policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto --More--   R7# R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pol R7(config)#policy-map extras2 R7(config-pmap)#class tel   ftp R7(config-pmap-c)#basnm   n R7(config-pmap-c)#bandwidth ? <8-2000000> Kilo Bits per second percent % of total Bandwidth remaining % of the remaining bandwidth R7(config-pmap-c)#bandwidth 256             pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 256  000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 256000 con R7(config-pmap-c)#police 256000 conform-action ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#police 256000 conform-action tr R7(config-pmap-c)#police 256000 conform-action transmit ? exceed-action action when rate is within conform and conform + exceed burst R7(config-pmap-c)#police 256000 conform-action transmit ex R7(config-pmap-c)#police 256000 conform-action transmit exceed-action ? drop drop packet set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#police 256000 conform-action transmit exceed-action c dr R7(config-pmap-c)#police 256000 conform-action transmit exceed-action drop ? violate-action action when rate is greater than conform + exceed burst R7(config-pmap-c)#police 256000 conform-action transmit exceed-action drop R7(config-pmap-c-police)#exit R7(config-pmap-c)#exit R7(config-pmap)#class telnet R7(config-pmap-c)#pol R7(config-pmap-c)#police 56000 1400        ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 1400 ? <1000-512000000> Burst bytes be Excess burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 1400 3500 ? conform-action action when rate is less than conform burst R7(config-pmap-c)#police 56000 1400 3500 con R7(config-pmap-c)#police 56000 1400 3500 conform-action tr R7(config-pmap-c)#police 56000 1400 3500 conform-action transmit          ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#police 56000 1400 3500 conform-action se R7(config-pmap-c)#police 56000 1400 3500 conform-action set-p R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit ? <0-7> new precedence R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 ? exceed-action action when rate is within conform and conform + exceed burst R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 e$0 1400 3500 conform-action set-prec-transmit 1 ex  R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action ? drop drop packet set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action se R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action set-p R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 ? violate-action action when rate is greater than conform + exceed burst R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 vi`  R7(config-pmap-c)#$smit 1 exceed-action set-prec-transmit 0 violate-action dr R7(config-pmap-c)#$eed-action set-prec-transmit 0 violate-action drop R7(config-pmap-c-police)#exit R7(config-pmap-c)#exit R7(config-pmap)#class class-default R7(config-pmap-c)#fai R7(config-pmap-c)#fair-queue ? <16-4096> Number Dynamic Conversation Queues R7(config-pmap-c)#fair-queue R7(config-pmap-c)#? QoS policy-map class configuration commands: bandwidth Bandwidth compression Activate Compression drop Drop all packets exit Exit from QoS class action configuration mode fair-queue Enable Flow-based Fair Queuing in this Class no Negate or set default values of a command police Police priority Strict Scheduling Priority for this Class queue-limit Queue Max Threshold for Tail Drop random-detect Enable Random Early Detection as drop policy service-policy Configure QoS Service Policy set Set QoS values shape Traffic Shaping R7(config-pmap-c)#qu R7(config-pmap-c)#queue-limit ? <1-512> Packets R7(config-pmap-c)#queue-limit 100 ? R7(config-pmap-c)#queue-limit 100   R7(config-pmap-c)#sh R7(config-pmap-c)#shape ? adaptive Enable Traffic Shaping adaptation to BECN average configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc only per interval fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fr-voice-adapt Enable rate adjustment depending on voice presence max-buffers Set Maximum Buffer Limit peak configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc+Be per interval R7(config-pmap-c)#shape       int s 1/0.1 R7(config-subif)#ser R7(config-subif)#service-policy extras2 out ^ % Invalid input detected at '^' marker. R7(config-subif)#service-policy extras2 out     extras2o extras2u extras2t extras2 extras2extras2  CBWFQ : Not supported on subinterfaces R7(config-subif)#do sh run int s 1/ *Mar 2 02:27:29.612: %ALIGN-3-SPURIOUS: Spurious memory access made at 0x804D2858 reading 0x8 R7(config-subif)#do sh run int s 1/0.1 Building configuration... Current configuration : 156 bytes ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 703 end R7(config-subif)#f frame-relay interface-dlci 703 %PVC is already defined R7(config-fr-dlci)#? Frame Relay dlci configuration commands: auto Configure Automation class Assign a mapclass to a dlci default Set a command to its defaults exit Exit from FR dlci configuration mode load-interval Specify interval for load calculation for a dlci no Negate a command or set its defaults vofr Voice over Frame-Relay R7(config-fr-dlci)#exit R7(config-subif)#exit R7(config)#fram map R7(config)#fram map        map R7(config)#map-c R7(config)#map-class fr R7(config)#map-class frame-relay prob    Extras2 R7(config-map-class)#ser R7(config-map-class)#service-policy extras2 ? % Unrecognized command R7(config-map-class)#service-policy extras2   ^ % Invalid input detected at '^' marker. R7(config-map-class)#service-policy extras2       ? input input policy output output policy R7(config-map-class)#service-policy out exytr   tras2 R7(config-map-class)#int s 1/0.1 R7(config-subif)#int s 1/0.1service-policy out extras2extras2 map-class frame-relay Extras2exit frame-relay interface-dlci 703 %PVC is already defined R7(config-fr-dlci)#m class extras2 R7(config-fr-dlci)#class extras2xtras2 Extras2 R7(config-fr-dlci)#do sh ru int       un int s 1/0.1 Building configuration... Current configuration : 172 bytes ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 703 class Extras2 end R7(config-fr-dlci)#^Z R7# *Mar 2 02:28:52.199: %SYS-5-CONFIG_I: Configured from console by console R7#sh pol int     ? WORD policy-map name interface Show Qos Policy Interface | Output modifiers R7#sh pol int ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Group-Async Async Group interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Access Virtual Access interface Virtual-FrameRelay Virtual Frame Relay interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing input Input policy output Output policy | Output modifiers --More--   R7#sh pol int ser 1/0.1 R7#sh pol int ser 1/0.1         out ? class Show statistics for a indvidual class | Output modifiers R7#sh pol int out class ? WORD class-map name R7#sh pol int out class Extras1 2 FastEthernet0/1 Service-policy output: extras R7#sh run | b class class-map match-all telnet match protocol telnet class-map match-all S5Other match access-group 101 class-map match-all S5Telnet match access-group 100 class-map match-all ftp match protocol ftp class-map match-all sql match protocol sqlserver match access-group 1 ! ! policy-map extras class ftp bandwidth percent 25 class telnet bandwidth percent 25 class sql priority 56 128 class class-default fair-queue 512 policy-map Prob6 --More--   class S5Telnet bandwidth 1000 class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 policy-map extras2 class ftp police cir 256000 conform-action transmit exceed-action drop class telnet police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop class class-default fair-queue queue-limit 100 ! ! ! ! --More--  interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output extras speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 1 ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 --More--   ip ospf network point-to-multipoint frame-relay interface-dlci 703 class Extras2 ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! --More--  interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless --More--  ! ! ! ! map-class frame-relay Prob7 frame-relay priority-group 1 ! map-class frame-relay Extras2 service-policy output extras2 ! map-class frame-relay extras2 access-list 1 permit 87.23.11.123 access-list 100 permit tcp host 208.28.1.2 any eq telnet access-list 101 permit ip host 208.28.1.2 any access-list 102 permit tcp any host 87.23.11.123 eq 1433 access-list 102 permit tcp any host 87.23.11.123 eq 1434 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! call rsvp-sync ! ! --More--   R7# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#do sh run class|class classiclass class class-map match-all telnet class-map match-all FTP class FTP class telnet class class-default ip classless R3(config)#do sh run int s 1/0 Building configuration... Current configuration : 261 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast end R3(config)#poli R3(config)#policy-map Prob18 R3(config-pmap)#class FTP R3(config-pmap-c)#sh R3(config-pmap-c)#shape ? adaptive Enable Traffic Shaping adaptation to BECN average configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc only per interval fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fr-voice-adapt Enable rate adjustment depending on voice presence max-buffers Set Maximum Buffer Limit peak configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc+Be per interval R3(config-pmap-c)#shape ac R3(config-pmap-c)#shape ac v R3(config-pmap-c)#shape average ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R3(config-pmap-c)#shape average 256000 R3(config-pmap-c)#exit R3(config-pmap)#class telnet R3(config-pmap-c)#sh av 56000 R3(config-pmap-c)#exit R3(config-pmap)#class class-f dfault     default % class map class-ddefault not configured R3(config-pmap)#class class-ddefaultdefault  R3(config-pmap-c)#sh pe R3(config-pmap-c)#sh peak ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R3(config-pmap-c)#sh peak      ? adaptive Enable Traffic Shaping adaptation to BECN average configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc only per interval fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fr-voice-adapt Enable rate adjustment depending on voice presence max-buffers Set Maximum Buffer Limit peak configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc+Be per interval R3(config-pmap-c)#sh pe R3(config-pmap-c)#sh peak 6000    ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R3(config-pmap-c)#sh peak 600000   000 R3(config-pmap-c)#int s 1/0 R3(config-if)#ser R3(config-if)#serr v R3(config-if)#service-policy Prob18 oProb18 uProb18 tProb18  Prob18  R3(config-if)#do sh pol in s 1/0 Serial1/0 Service-policy output: Prob18 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 256000/256000 1984 7936 7936 31 992 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Traffic Shaping Target/Average Byte Sustain Excess Interval Increment --More--   Rate Limit bits/int bits/int (ms) (bytes) 56000/56000 1988 7952 7952 142 994 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no Class-map: class-default (match-any) 1 packets, 13 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 1200000/600000 3750 15000 15000 25 3750 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no R3(config-if)#popl   pol     ol prob        exit R3(config)#pol R3(config)#policy-map Prob18 R3(config-pmap)#class class-f default R3(config-pmap-c)#class class-defaultpolicy-map Prob18 exit do sh pol in s 1/0service-policy out Prob18 int s 1/0 sh peak 600000nsh peak 600000osh peak 600000 sh peak 600000 R3(config-pmap-c)#pol R3(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R3(config-pmap-c)#police 512000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R3(config-pmap-c)#police 512000 pir ? <8000-2000000000> Bits per second R3(config-pmap-c)#police 512000 pir 60000  000p  R3(config-pmap-c-police)#exit R3(config-pmap-c)#exitpolice 512000 pir 600000no sh peak 600000 class class-defaultpolicy-map Prob18 class class-defaultno sh peak 600000 police 512000 pir 600000no sh peak 600000 class class-defaultpolicy-map Prob18 class class-defaultpolicy-map Prob18 exit do sh pol in s 1/0 Serial1/0 Service-policy output: Prob18 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 256000/256000 1984 7936 7936 31 992 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Traffic Shaping Target/Average Byte Sustain Excess Interval Increment --More--   Rate Limit bits/int bits/int (ms) (bytes) 56000/56000 1988 7952 7952 142 994 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no Class-map: class-default (match-any) 22 packets, 886 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any police: cir 512000 bps, bc 16000 bytes pir 600000 bps, be 16000 bytes conformed 0 packets, 0 bytes; actions: transmit exceeded 0 packets, 0 bytes; actions: drop violated 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps, violate 0 bps R3(config-pmap-c)#^Z R3#sh run | *Mar 2 02:42:41.475: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b class class-map match-all telnet match protocol telnet class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 policy-map Prob18 class FTP shape average 256000 class telnet shape average 56000 class class-default police cir 512000 pir 600000 ! ! ! --More--  ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 100 ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 service-policy output Prob18 encapsulation frame-relay --More--   ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 --More--   no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless ! ! ! access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo --More--   R3# RACK14AS>2 [Resuming connection 2 to r2 ... ] * R2(config-if)#tr R2(config-if)#traf R2(config-if)#traffic-shape               int s 1/0.1 R2(config-subif)#tr R2(config-subif)#traffic-shape ? adaptive Enable Traffic Shaping adaptation to BECN fecn-adapt Enable Traffic Shaping reflection of FECN as BECN group configure token bucket: group CIR (bps) [Bc (bits) [Be (bits)]] rate configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]] R2(config-subif)#traffic-shape rat R2(config-subif)#traffic-shape rate ? <8000-100000000> Target Bit Rate (bits per second) R2(config-subif)#traffic-shape rate 64000 ? <0-100000000> bits per interval, sustained R2(config-subif)#traffic-shape rate 64000 Shaping is not allowed simultaneously at the physical interface and subinterfaces or at interface/subinterface and PVCs R2(config-subif)#do sh run int s 1. /0 Building configuration... Current configuration : 113 bytes ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping end R2(config-subif)#int     do sh ru8n    n | b interface Serial1/0 interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob4 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 --More--   ip address 180.40.7.2 255.255.255.224 clockrate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! --More--  router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless no ip forward-protocol udp netbios-dgm ! ! ! ! map-class frame-relay Prob4 frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn access-list 100 deny ospf any any access-list 100 permit ip any any ! ! call rsvp-sync ! --More--   R2(config-subif)#int s 1/0 R2(config-if)#no fram tr R2(config-if)#no fram traf R2(config-if)#no fram traffic-shaping R2(config-if)#int s 1/0.2 R2(config-subif)#fram inter R2(config-subif)#fram interface-dlci 27 R2(config-fr-dlci)# *Mar 2 02:47:36.743: %FR-4-DLCIDELETE: Interface Serial1/0 - DLCI 207 - PVC use count 1 R2(config-fr-dlci)#fram interface-dlci 27nfram interface-dlci 27ofram interface-dlci 27 fram interface-dlci 27 R2(config-subif)#no fram interface-dlci 27fram interface-dlci 27  *Mar 2 02:47:42.120: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-subif)#fram interface-dlci 27 07 R2(config-fr-dlci)#no class Prob4 R2(config-fr-dlci)# *Mar 2 02:47:51.042: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on Serial1/0.2 from LOADING to FULL, Loading Done R2(config-fr-dlci)#exit R2(config-subif)#do sh ru int      mn    n int s 1/0.2 Building configuration... Current configuration : 185 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay de-group 1 207 frame-relay interface-dlci 207 end R2(config-subif)#tr R2(config-subif)#traffic-shape rate 64000 R2(config-subif)#inttraffic-shape rate 64000do sh run int s 1/0.2  1 Building configuration... Current configuration : 156 bytes ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 203 end R2(config-subif)#do sh run int s 1/0.1traffic-shape rate 64000do sh run int s 1/0.2 exit no class Prob4fram interface-dlci 207no fram interface-dlci 27fram interface-dlci 27 int s 1/0.2  1 R2(config-subif)#int s 1/0.1do sh run int s 1/0.1traffic-shape rate 64000 R2(config-subif)#do sh traff int s 1  1/0.1 sh traff int s1/0.1 ^ % Invalid input detected at '^' marker. R2(config-subif)#do sh traff int s1/0.1.1           Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 - Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 - R2(config-subif)#ra R2(config-subif)#rate-limit ? input Rate limit on input output Rate limit on output R2(config-subif)#rate-limit out ? <8000-2000000000> Bits per second access-group Match access list dscp Match dscp value qos-group Match qos-group ID R2(config-subif)#rate-limit out 64000 ? <1000-512000000> Normal burst bytes R2(config-subif)#rate-limit out 64000 1000 ? <2000-1024000000> Maximum burst bytes R2(config-subif)#rate-limit out 64000 1000 100   2000 ? conform-action action when rate not exceeded R2(config-subif)#rate-limit out 64000 1000 2000 cp   o ? continue scan other rate limits drop drop packet set-dscp-continue set dscp, scan other rate limits set-dscp-transmit set dscp and send it set-mpls-exp-imposition-continue set exp during imposition, scan other rate limits set-mpls-exp-imposition-transmit set exp during imposition and send it set-prec-continue rewrite packet precedence, scan other rate limits set-prec-transmit rewrite packet precedence and send it set-qos-continue set qos-group, scan other rate limits set-qos-transmit set qos-group and send it transmit transmit packet R2(config-subif)#rate-limit out 64000 1000 2000 co                                   sh    do sh run | b interface Serail  1  l1/0 R2(config-subif)#do sh run | b interface Serail1/0traff run | b interface Serail1/0      ial1/0 interface Serial1/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 8000 8000 1000 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 8000 8000 1000 frame-relay de-group 1 207 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 --More--   R2(config-subif)# R2# *Mar 2 02:54:25.108: %SYS-5-CONFIG_I: Configured from console by console R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 12 /0.1 R2(config-subif)#tra R2(config-subif)#traffic-shape ? adaptive Enable Traffic Shaping adaptation to BECN fecn-adapt Enable Traffic Shaping reflection of FECN as BECN group configure token bucket: group CIR (bps) [Bc (bits) [Be (bits)]] rate configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]] R2(config-subif)#traffic-shape a R2(config-subif)#traffic-shape adaptive ? <1-100000000> Lower Bound Target Bit Rate (bits per second) R2(config-subif)#traffic-shape adaptive 32000 ? R2(config-subif)#traffic-shape adaptive 32000   R2(config-subif)#int s 1/0.2 R2(config-subif)#int s 1/0.2traffic-shape adaptive 32000 R2(config-subif)#^Z R2#sh r *Mar 2 02:55:11.985: %SYS-5-CONFIG_I: Configured from console by console R2#sh run inconfig t sh run int fa 0/1                 config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#traffic-shape adaptive 32000int s 1/0.2 traffic-shape adaptive 32000int s 1/0.1 do sh run | b interface Serial1/0 interface Serial1/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 8000 8000 1000 traffic-shape adaptive 32000 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 8000 8000 1000 traffic-shape adaptive 32000 frame-relay de-group 1 207 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address shutdown --More--   R2(config)#do sh traff Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 BECN Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 BECN R2(config)# R2# *Mar 2 02:55:50.172: %SYS-5-CONFIG_I: Configured from console by console R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1./  /2 Building configuration... Current configuration : 123 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 end R3#sh run | i   b policy policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 policy-map Prob18 class FTP shape average 256000 class telnet shape average 56000 class class-default police cir 512000 pir 600000 ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto --More--   R3#sh run a     access-list Extended IP access list 100 10 permit icmp host 100.1.1.1 host 20.10.1.2 echo (112 matches) Extended IP access list 101 10 permit icmp host 100.1.1.1 host 20.10.1.1 echo (27 matches) Extended IP access list 102 10 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo (45 matches) R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#access-list 199 er  per ip    tcp any any eq ftp R3(config)#access-list 199 per tcp any any eq ftp   R3(config)#access-list 199 per tcp any any eq ftp-dat R3(config)#access-list 199 per tcp any any eq ftp-dat       telnet R3(config)#do shg    h access-list Extended IP access list 100 10 permit icmp host 100.1.1.1 host 20.10.1.2 echo (112 matches) Extended IP access list 101 10 permit icmp host 100.1.1.1 host 20.10.1.1 echo (27 matches) Extended IP access list 102 10 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo (45 matches) Extended IP access list 199 10 permit tcp any any eq ftp 20 permit tcp any any eq ftp-data 30 permit tcp any any eq telnet R3(config)#ip access-list ex 199 R3(config-ext-nacl)#15 per udp any any eq tftp R3(config-ext-nacl)#15 per udp any any eq tftpip access-list ex 199 do sh access-list  Extended IP access list 100 10 permit icmp host 100.1.1.1 host 20.10.1.2 echo (112 matches) Extended IP access list 101 10 permit icmp host 100.1.1.1 host 20.10.1.1 echo (27 matches) Extended IP access list 102 10 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo (45 matches) Extended IP access list 199 10 permit tcp any any eq ftp 15 permit udp any any eq tftp 20 permit tcp any any eq ftp-data 30 permit tcp any any eq telnet R3(config-ext-nacl)#no 20 R3(config-ext-nacl)#no 20do sh access-list Extended IP access list 100 10 permit icmp host 100.1.1.1 host 20.10.1.2 echo (112 matches) Extended IP access list 101 10 permit icmp host 100.1.1.1 host 20.10.1.1 echo (27 matches) Extended IP access list 102 10 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo (45 matches) Extended IP access list 199 10 permit tcp any any eq ftp 15 permit udp any any eq tftp 30 permit tcp any any eq telnet R3(config-ext-nacl)#exit R3(config)#no a access-list 199 R3(config)#no access-list 199exit do sh access-listno 20 do sh access-list15 per udp any any eq tftpip access-list ex 199  R3(config-ext-nacl)#ip access-list ex 199no access-list 199  R3(config)#^Z R3# RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/4, Fa0/5 Fa0/6, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Gi0/1, Gi0/2 10 VLAN0010 active Fa0/3 16 VLAN0016 active 20 VLAN0020 active 30 VLAN0030 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 16 enet 100016 1500 - - - - - 0 0 --More--   S5(config)#vlan 99 S5(config-vlan)#name Voice S5(config-vlan)#int fa0/21 S5(config-if)#swi S5(config-if)#switchport mode S5(config-if)#switchport mode dot S5(config-if)#switchport mode dot1q-tunnel S5(config-if)#switchport mode dot1q-tunnel                     int fa0/21   switchport mode dot1q-tunnel              tru S5(config-if)#switchport mode trunk            en S5(config-if)#switchport en  tru S5(config-if)#switchport trunk en S5(config-if)#switchport trunk encapsulation dot S5(config-if)#switchport trunk encapsulation dot1q S5(config-if)#switchport trunk encapsulation dot1q                           mode trunk S5(config-if)#swi S5(config-if)#switchport ? access Set access mode characteristics of the interface block Disable forwarding of unknown uni/multi cast addresses broadcast Set broadcast suppression level on this interface host Set port host mode Set trunking mode of the interface multicast Set multicast suppression level on this interface nonegotiate Device will not engage in negotiation protocol on this interface port-security Security related command priority Set appliance 802.1p priority protected Configure an interface to be a protected port trunk Set trunking characteristics of the interface unicast Set unicast suppression level on this interface voice Voice appliance attributes S5(config-if)#switchport voi S5(config-if)#switchport voice ? vlan Vlan for voice traffic S5(config-if)#switchport voice vlan ? <1-4094> Vlan for voice traffic dot1p Priority tagged on PVID none Don't tell telephone about voice vlan untagged Untagged on PVID S5(config-if)#switchport voice vlan 99 ? S5(config-if)#switchport voice vlan 99 S5(config-if)#sw S5(config-if)#switchport ? access Set access mode characteristics of the interface block Disable forwarding of unknown uni/multi cast addresses broadcast Set broadcast suppression level on this interface host Set port host mode Set trunking mode of the interface multicast Set multicast suppression level on this interface nonegotiate Device will not engage in negotiation protocol on this interface port-security Security related command priority Set appliance 802.1p priority protected Configure an interface to be a protected port trunk Set trunking characteristics of the interface unicast Set unicast suppression level on this interface voice Voice appliance attributes S5(config-if)#switchport pri S5(config-if)#switchport priority ? extend Set appliance 802.1p priority S5(config-if)#switchport priority e S5(config-if)#switchport priority extend ? cos Override 802.1p priority of devices on appliance trust Trust 802.1p priorities of devices on appliance S5(config-if)#switchport priority extend co S5(config-if)#switchport priority extend cos 1 S5(config-if)#do sh mls qos QoS is disabled S5(config-if)#exit S5(config)#mls qos ? aggregate-policer Assign aggregate policer cos Configure CoS setting map Define QoS mapping min-reserve Configure min-reserve buffers S5(config)#mls qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S5(config)#int fa 0/21 S5(config-if)#swq w S5(config-if)#sww  S5(config-if)#switchport pr S5(config-if)#switchport pr    ? access Set access mode characteristics of the interface block Disable forwarding of unknown uni/multi cast addresses broadcast Set broadcast suppression level on this interface host Set port host mode Set trunking mode of the interface multicast Set multicast suppression level on this interface nonegotiate Device will not engage in negotiation protocol on this interface port-security Security related command priority Set appliance 802.1p priority protected Configure an interface to be a protected port trunk Set trunking characteristics of the interface unicast Set unicast suppression level on this interface voice Voice appliance attributes S5(config-if)#switchport pr S5(config-if)#switchport pri S5(config-if)#switchport priority ? extend Set appliance 802.1p priority S5(config-if)#switchport priority                     mls ? qos Configure interface QoS parameters S5(config-if)#mls qos ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S5(config-if)#mls qos tru S5(config-if)#mls qos trust ? cos Classify by packet COS device trusted device class dscp Classify by packet DSCP ip-precedence Classify by packet IP precedence S5(config-if)#mls qos trust co S5(config-if)#mls qos trust cos S5(config-if)#^Z S5#sh ru 1d04h: %SYS-5-CONFIG_I: Configured from console by console S5#sh ru  n | b mls qos mls qos ! spanning-tree mode pvst spanning-tree extend system-id ! ! ! ! ! interface FastEthernet0/1 switchport mode dynamic desirable ! interface FastEthernet0/2 switchport mode dynamic desirable ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport mode dynamic desirable ! interface FastEthernet0/5 --More--   switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 no switchport ip address 208.28.1.2 255.255.255.0 ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable --More--  ! interface FastEthernet0/13 switchport mode dynamic desirable ! interface FastEthernet0/14 switchport mode dynamic desirable ! interface FastEthernet0/15 switchport mode dynamic desirable ! interface FastEthernet0/16 switchport mode dynamic desirable ! interface FastEthernet0/17 switchport mode dynamic desirable ! interface FastEthernet0/18 switchport mode dynamic desirable ! interface FastEthernet0/19 switchport mode dynamic desirable ! interface FastEthernet0/20 --More--   switchport mode dynamic desirable ! interface FastEthernet0/21 switchport trunk encapsulation dot1q switchport mode trunk switchport voice vlan 99 switchport priority extend cos 1 mls qos trust cos spanning-tree portfast ! interface FastEthernet0/22 switchport mode dynamic desirable ! interface FastEthernet0/23 switchport mode dynamic desirable ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! --More--   S5# S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#span S5(config)#spanning-tree ? backbonefast Enable BackboneFast Feature etherchannel Spanning tree etherchannel specific configuration extend Spanning Tree 802.1t extensions loopguard Spanning tree loopguard options mode Spanning tree operating mode mst Multiple spanning tree configuration pathcost Spanning tree pathcost options portfast Spanning tree portfast options uplinkfast Enable UplinkFast Feature vlan VLAN Switch Spanning Tree S5(config)#spanning-tree mode                    ^Z S5#sh 1d04h: %SYS-5-CONFIG_I: Configured from console by console S5#sh span S5#sh spanning-tree VLAN0001 Spanning tree enabled protocol ieee Root ID Priority 32769 Address 0013.80cf.ce00 This bridge is the root Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32769 (priority 32768 sys-id-ext 1) Address 0013.80cf.ce00 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 Interface Role Sts Cost Prio.Nbr Type ---------------- ---- --- --------- -------- -------------------------------- Fa0/1 Desg FWD 100 128.1 Shr Fa0/8 Desg FWD 100 128.8 Shr Fa0/23 Desg FWD 19 128.23 P2p Fa0/24 Desg FWD 19 128.24 P2p --More--   VLAN0010 Spanning tree enabled protocol ieee Root ID Priority 32778 Address 0013.80cf.ce00 This bridge is the root Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32778 (priority 32768 sys-id-ext 10) Address 0013.80cf.ce00 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 Interface Role Sts Cost Prio.Nbr Type ---------------- ---- --- --------- -------- -------------------------------- Fa0/3 Desg FWD 19 128.3 P2p Fa0/24 Desg FWD 19 128.24 P2p --More--   S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#sp S5(config)#spanning-tree ? backbonefast Enable BackboneFast Feature etherchannel Spanning tree etherchannel specific configuration extend Spanning Tree 802.1t extensions loopguard Spanning tree loopguard options mode Spanning tree operating mode mst Multiple spanning tree configuration pathcost Spanning tree pathcost options portfast Spanning tree portfast options uplinkfast Enable UplinkFast Feature vlan VLAN Switch Spanning Tree S5(config)#spanning-tree mode ? mst Multiple spanning tree mode pvst Per-Vlan spanning tree mode rapid-pvst Per-Vlan rapid spanning tree mode S5(config)#spanning-tree mode mst ? S5(config)#spanning-tree mode mst                        ^Z S5# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#config t ^ % Invalid input detected at '^' marker. R4(config)#do sh run | i class ip classless R4(config)#class   R4(config)#class-map ping R4(config-cmap)#match pro R4(config-cmap)#match protocol e? egp eigrp exchange R4(config-cmap)#match protocol e icmp? icmp R4(config-cmap)#match protocol icmp ? R4(config-cmap)#match protocol icmp                     exit R4(config)#do sh run acce    | i access access-list 100 permit icmp any any echo R4(config)#access-list 101 per ospf any any R4(config)#class R4(config)#class-map ping R4(config-cmap)#match acc R4(config-cmap)#match access-group 1200   00 R4(config-cmap)#exit R4(config)#clas R4(config)#class-map ospf R4(config-cmap)#cl  match acc R4(config-cmap)#match access-group 101 R4(config-cmap)#exit R4(config)#class R4(config)#class-map wed b R4(config-cmap)#pro R4(config-cmap)#proo R4(config-cmap)#proo    mat R4(config-cmap)#match pro R4(config-cmap)#match protocol ? arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 dhcp Dynamic Host Configuration dlsw Data Link Switching dns Domain Name Server lookup egp Exterior Gateway Protocol --More--   eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) ipsec IP Security Protocol (ESP/AH) ipv6 IPV6 ipx Novell IPX irc Internet Relay Chat kazaa2 Kazaa Version 2 kerberos Kerberos l2tp L2F/L2TP tunnel ldap Lightweight Directory Access Protocol llc2 llc2 napster Napster Traffic --More--   netbios NetBIOS netshow Microsoft Netshow nfs Network File System nntp Network News Transfer Protocol notes Lotus Notes(R) novadigm Novadigm EDM ntp Network Time Protocol pad PAD links pcanywhere Symantec pcANYWHERE pop3 Post Office Protocol pppoe PPP over Ethernet pptp Point-to-Point Tunneling Protocol printer print spooler/lpd qllc qllc protocol rcmd BSD r-commands (rsh, rlogin, rexec) realaudio Real Audio streaming protocol rip Routing Information Protocol rsrb Remote Source-Route Bridging rsvp Resource Reservation Protocol rtp Real Time Protocol rtspplayer RTSP players streaming protocol secure-ftp FTP over TLS/SSL secure-http Secured HTTP --More--   secure-imap Internet Message Access Protocol over TLS/SSL secure-irc Internet Relay Chat over TLS/SSL secure-ldap Lightweight Directory Access Protocol over TLS/SSL secure-nntp Network News Transfer Protocol over TLS/SSL secure-pop3 Post Office Protocol over TLS/SSL secure-telnet Telnet over TLS/SSL smtp Simple Mail Transfer Protocol snapshot Snapshot routing support snmp Simple Network Mangement Protocol socks SOCKS sqlnet SQL*NET for Oracle sqlserver MS SQL Server ssh Secured Shell streamwork Xing Technology StreamWorks player stun Serial Tunnel sunrpc Sun RPC syslog System Logging Utility telnet Telnet tftp Trivial File Transfer Protocol vdolive VDOLive streaming video vofr voice over Frame Relay packets xwindows X-Windows remote access R4(config-cmap)#match protocol http ? host Server Host Name mime Match MIME Type url Match URL String R4(config-cmap)#match protocol http R4(config-cmap)#exit R4(config)#ip cef R4(config)#pol R4(config)#policy-map Prob21 R4(config-pmap)#class ping R4(config-pmap-c)#? QoS policy-map class configuration commands: bandwidth Bandwidth compression Activate Compression drop Drop all packets exit Exit from QoS class action configuration mode no Negate or set default values of a command police Police priority Strict Scheduling Priority for this Class queue-limit Queue Max Threshold for Tail Drop random-detect Enable Random Early Detection as drop policy service-policy Configure QoS Service Policy set Set QoS values shape Traffic Shaping R4(config-pmap-c)#set ? atm-clp Set ATM CLP bit to 1 cos Set IEEE 802.1Q/ISL class of service/user priority discard-class Discard behavior identifier dscp Set DSCP in IP(v4) and IPv6 packets fr-de Set FR DE bit to 1 ip Set IP specific values mpls Set MPLS specific values precedence Set precedence in IP(v4) and IPv6 packets qos-group Set QoS Group R4(config-pmap-c)#set ds R4(config-pmap-c)#set dscp ? <0-63> Differentiated services codepoint value af11 Match packets with AF11 dscp (001010) af12 Match packets with AF12 dscp (001100) af13 Match packets with AF13 dscp (001110) af21 Match packets with AF21 dscp (010010) af22 Match packets with AF22 dscp (010100) af23 Match packets with AF23 dscp (010110) af31 Match packets with AF31 dscp (011010) af32 Match packets with AF32 dscp (011100) af33 Match packets with AF33 dscp (011110) af41 Match packets with AF41 dscp (100010) af42 Match packets with AF42 dscp (100100) af43 Match packets with AF43 dscp (100110) cos Set packet DSCP from L2 COS cs1 Match packets with CS1(precedence 1) dscp (001000) cs2 Match packets with CS2(precedence 2) dscp (010000) cs3 Match packets with CS3(precedence 3) dscp (011000) cs4 Match packets with CS4(precedence 4) dscp (100000) cs5 Match packets with CS5(precedence 5) dscp (101000) cs6 Match packets with CS6(precedence 6) dscp (110000) cs7 Match packets with CS7(precedence 7) dscp (111000) default Match packets with default dscp (000000) --More--   R4(config-pmap-c)#set dscp af31 R4(config-pmap-c)#exci  it R4(config-pmap)#class R4(config-pmap)#class ospf R4(config-pmap-c)#set ds af43 R4(config-pmap-c)#exit R4(config-pmap)#class web R4(config-pmap-c)#set dsc af21 R4(config-pmap-c)#exit R4(config-pmap)#class class-default R4(config-pmap-c)#set af    ds R4(config-pmap-c)#set dscp af12 R4(config-pmap-c)#int fa 0/0 R4(config-if)#ser R4(config-if)#service-policy out Prob21 R4(config-if)#^Z R4# *Mar 2 04:31:45.760: %SYS-5-CONFIG_I: Configured from console by console R4#sh pol R4#sh policy-map int fa 0/0 FastEthernet0/0 Service-policy output: Prob21 Class-map: ping (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 100 QoS Set dscp af31 Packets marked 0 Class-map: ospf (match-all) 2 packets, 196 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 101 QoS Set dscp af43 Packets marked 2 Class-map: web (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps --More--   R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R4#ping 20.10.1.1 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R4#sh run   ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.133 YES DHCP up up ATM1/0 unassigned YES unset administratively down down Virtual-Access1 unassigned YES unset up up Loopback0 100.1.1.1 YES manual up up R4# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip int briue  e Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 20.10.1.1 YES manual administratively down down Serial1/0 unassigned YES unset up up Serial1/0.1 180.40.7.67 YES manual up up Serial1/0.2 180.40.7.162 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.2 YES manual up up Serial1/3 unassigned YES unset administratively down down --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#bint    int fa 0/0 1 R2(config-if)#no shut R2(config-if)#^Z R2# *Mar 2 04:30:51.169: %SYS-5-CONFIG_I: Configured from console by console R2# *Mar 2 04:30:52.640: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up R2# *Mar 2 04:30:58.237: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R2# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip int brieping 20.10.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R4#ping 20.10.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: .. RACK14AS>6 [Resuming connection 6 to r6 ... ] 1d S6#sh spna int 1d04h: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on FastEthernet0/2 from LOADING to FULL, Loading Done S6#sh spna int fa 0/                  RACK14AS>4 [Resuming connection 4 to r4 ... ] .. R4#ping 20.10.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: ....! Success rate is 20 percent (1/5), round-trip min/avg/max = 60/60/60 ms R4#sh route route-map Prob3, permit, sequence 10 Match clauses: ip address (access-lists): 100 Set clauses: ip next-hop 180.40.7.129 Policy routing matches: 50 packets, 5000 bytes R4#sh route sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is 180.40.7.132 to network 0.0.0.0 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 00:00:09, FastEthernet0/0 [110/793] via 180.40.7.131, 00:00:09, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.129, 00:00:09, FastEthernet0/0 [110/783] via 180.40.7.131, 00:00:09, FastEthernet0/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:09, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.129, 00:00:11, FastEthernet0/0 [110/782] via 180.40.7.131, 00:00:11, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:00:11, FastEthernet0/0 --More--  O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:11, FastEthernet0/0 O 180.40.7.67/32 [110/782] via 180.40.7.129, 00:00:11, FastEthernet0/0 [110/782] via 180.40.7.131, 00:00:11, FastEthernet0/0 O 180.40.7.66/32 [110/1] via 180.40.7.129, 00:00:11, FastEthernet0/0 O 180.40.7.65/32 [110/1] via 180.40.7.131, 00:00:11, FastEthernet0/0 S* 0.0.0.0/0 [254/0] via 180.40.7.132 R4#sh ip routeroute ping 20.10.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 ms R4#ping 20.10.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 ms R4#ping 20.10.1.2sh ip route  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is 180.40.7.132 to network 0.0.0.0 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 00:00:17, FastEthernet0/0 [110/793] via 180.40.7.131, 00:00:17, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.129, 00:00:17, FastEthernet0/0 [110/783] via 180.40.7.131, 00:00:17, FastEthernet0/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:17, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.129, 00:00:18, FastEthernet0/0 [110/782] via 180.40.7.131, 00:00:18, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:00:18, FastEthernet0/0 --More--   R4#sh pol int fa 0/0 FastEthernet0/0 Service-policy output: Prob21 Class-map: ping (match-all) 35 packets, 3990 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 100 QoS Set dscp af31 Packets marked 35 Class-map: ospf (match-all) 20 packets, 1992 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 101 QoS Set dscp af43 Packets marked 20 Class-map: web (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps --More--   Match: protocol http QoS Set dscp af21 Packets marked 0 Class-map: class-default (match-any) 19 packets, 2058 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any QoS Set dscp af12 Packets marked 0 R4#sh run | b class class-map match-all ospf match access-group 101 class-map match-all ping match access-group 100 class-map match-all web match protocol http ! ! policy-map Prob21 class ping set dscp af31 class ospf set dscp af43 class web set dscp af21 class class-default set dscp af12 ! ! ! ! interface Loopback0 ip address 100.1.1.1 255.255.255.0 --More--  ! interface FastEthernet0/0 ip address dhcp service-policy output Prob21 duplex auto speed auto ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip local policy route-map Prob3 no ip http server ip classless ! ! ! access-list 100 permit icmp any any echo --More--  access-list 101 permit ospf any any ! route-map Prob3 permit 10 match ip address 100 set ip next-hop 180.40.7.129 ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login --More--   R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run | i   int s 1. /2 Building configuration... Current configuration : 123 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 end R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/. 2 R3(config-if)#mnop    no service-policy output Prob9 R3(config-if)#no max-reserved-bandwidth 100 R3(config-if)#no max-reserved-bandwidth 100no max-reserved-bandwidth 100  max-reserved-bandwidth 100  max-reserved-bandwidth 100   80 R3(config-if)#exit R3(config)#class   R3(config)#class-map dscp12 R3(config-cmap)#match ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R3(config-cmap)#match s dsc R3(config-cmap)#match dscp ? <0-63> Differentiated services codepoint value af11 Match packets with AF11 dscp (001010) af12 Match packets with AF12 dscp (001100) af13 Match packets with AF13 dscp (001110) af21 Match packets with AF21 dscp (010010) af22 Match packets with AF22 dscp (010100) af23 Match packets with AF23 dscp (010110) af31 Match packets with AF31 dscp (011010) af32 Match packets with AF32 dscp (011100) af33 Match packets with AF33 dscp (011110) af41 Match packets with AF41 dscp (100010) af42 Match packets with AF42 dscp (100100) af43 Match packets with AF43 dscp (100110) cs1 Match packets with CS1(precedence 1) dscp (001000) cs2 Match packets with CS2(precedence 2) dscp (010000) cs3 Match packets with CS3(precedence 3) dscp (011000) cs4 Match packets with CS4(precedence 4) dscp (100000) cs5 Match packets with CS5(precedence 5) dscp (101000) cs6 Match packets with CS6(precedence 6) dscp (110000) cs7 Match packets with CS7(precedence 7) dscp (111000) default Match packets with default dscp (000000) ef Match packets with EF dscp (101110) --More--   R3(config-cmap)#match dscp 12 R3(config-cmap)#exit R3(config)#clas R3(config)#class-map dscp18 R3(config-cmap)#match dscp 18 R3(config-cmap)#exit R3(config)#exitmatch dscp 18class-map dscp18  26 R3(config-cmap)#match dscp 26 R3(config-cmap)#exit R3(config)#do sh run | I CL    B CLASS     class class-map match-all dscp26 match dscp af31 class-map match-all telnet match protocol telnet class-map match-all dscp12 match dscp af12 class-map match-all dscp18 match dscp af21 class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 policy-map Prob18 class FTP shape average 256000 class telnet --More--   shape average 56000 --More--   R3(config)#pol R3(config)#policy-map Prob22 R3(config-pmap)#class dscp12 R3(config-pmap-c)#ban R3(config-pmap-c)#bandwidth p R3(config-pmap-c)#bandwidth percent 15 R3(config-pmap-c)#exit R3(config-pmap)#class dscp18 R3(config-pmap-c)#class dscp18exit bandwidth percent 15 R3(config-pmap-c)#bandwidth percent 15class dscp18   26 R3(config-pmap-c)#class dscp26bandwidth percent 15  50 R3(config-pmap-c)#int s 1/2 R3(config-if)#ser R3(config-if)#serv R3(config-if)#service-policy out Prob3 22 R3(config-if)#^Z R3# *Mar 2 04:47:17.346: %SYS-5-CONFIG_I: Configured from console by console R3# RACK14AS>4 [Resuming connection 4 to r4 ... ]  R4#sh run | b classpol int fa 0/0ip route ping 20.10.1.2 RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh route route-map Prob1, permit, sequence 10 Match clauses: ip address (access-lists): 100 length 0 1000 Set clauses: ip next-hop 180.40.7.67 Policy routing matches: 94 packets, 10836 bytes route-map Prob1, permit, sequence 20 Match clauses: ip address (access-lists): 102 length 1001 2147483647 Set clauses: interface Serial1/2 Policy routing matches: 18 packets, 26652 bytes route-map Prob1, permit, sequence 30 Match clauses: ip address (access-lists): 101 Set clauses: interface Serial1/2 Policy routing matches: 27 packets, 3078 bytes R3#wsh routew  sh access-list Extended IP access list 100 10 permit icmp host 100.1.1.1 host 20.10.1.2 echo (112 matches) Extended IP access list 101 10 permit icmp host 100.1.1.1 host 20.10.1.1 echo (27 matches) Extended IP access list 102 10 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo (45 matches) R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 ms R4#ping 20.10.1.2 1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/54/60 ms R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 48/55/60 ms R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 48/57/60 ms R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh popl   ol  R3#sh pol   R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 17 packets, 1208 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no iu   p cef CEF is required for 'match protocol' or 'protocol-discovery commands that are currently active R3(config)#do sh run ip  | cef sh run | cef ^ % Invalid input detected at '^' marker. R3(config)#do sh run | ceficef cef R3(config)#^Z R3# *Mar 2 04:49:40.981: %SYS-5-CONFIG_I: Configured from console by console R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/47/60 ms R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/48/60 ms R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config tsh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 41 packets, 3364 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/50/64 ms R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 49 packets, 3916 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK14AS>5 [Resuming connection 5 to r5 ... ] 1d04h: S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#u int fa 0/4 S5(config-if)#ml S5(config-if)#mls qo S5(config-if)#mls qos t S5(config-if)#mls qos trust ? cos Classify by packet COS device trusted device class dscp Classify by packet DSCP ip-precedence Classify by packet IP precedence S5(config-if)#mls qos trust ds S5(config-if)#mls qos trust dscp S5(config-if)#^Z S5# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/49/60 ms R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 66 packets, 5224 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# sh policy-map int s 1/2  RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/47/64 ms R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/52/64 ms R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/47/60 ms R4#ping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/49/64 ms R4# R4#ping Protocol [ip]: Target IP address: 20.1. 0.1.1 Repeat count [5]: 10000000 Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 10000000, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!! RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 128 packets, 11692 bytes 5 minute offered rate 1000 bps, drop rate 0 bps Match: any R3# RACK14AS> [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.133, 00:20:09, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.2, 00:20:10, Serial1/2 [110/792] via 180.40.7.67, 00:20:10, Serial1/0 O 20.10.1.0 [110/782] via 180.40.7.2, 00:20:10, Serial1/2 [110/782] via 180.40.7.67, 00:20:10, Serial1/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:20:10, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.2, 00:20:11, Serial1/2 [110/781] via 180.40.7.67, 00:20:11, Serial1/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:20:11, FastEthernet0/0 --More--   R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.133, 00:20:14, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.2, 00:20:14, Serial1/2 [110/792] via 180.40.7.67, 00:20:14, Serial1/0 O 20.10.1.0 [110/782] via 180.40.7.2, 00:20:14, Serial1/2 [110/782] via 180.40.7.67, 00:20:14, Serial1/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:20:14, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.2, 00:20:15, Serial1/2 [110/781] via 180.40.7.67, 00:20:15, Serial1/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:20:15, FastEthernet0/0 --More--   R3#[Ash ip route policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 316 packets, 31044 bytes 5 minute offered rate 5000 bps, drop rate 0 bps Match: any R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 393 packets, 38972 bytes 5 minute offered rate 5000 bps, drop rate 0 bps Match: any R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 419 packets, 41656 bytes 5 minute offered rate 7000 bps, drop rate 0 bps Match: any R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Success rate is 100 percent (892/892), round-trip min/avg/max = 32/49/176 ms R4#sh pol int fa 0/09  FastEthernet0/0 Service-policy output: Prob21 Class-map: ping (match-all) 987 packets, 112518 bytes 5 minute offered rate 11000 bps, drop rate 0 bps Match: access-group 100 QoS Set dscp af31 Packets marked 987 Class-map: ospf (match-all) 145 packets, 14202 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 101 QoS Set dscp af43 Packets marked 145 Class-map: web (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps --More--   Match: protocol http QoS Set dscp af21 Packets marked 0 Class-map: class-default (match-any) 163 packets, 16852 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any QoS Set dscp af12 Packets marked 0 R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3# RACK14AS>5 [Resuming connection 5 to r5 ... ] 1d0 S5#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID FrameRelay Fas 0/8 166 R 2520 Eth 0 R3 Fas 0/3 151 R S 2611XM Fas 0/0 R7 Fas 0/7 159 R S 2611XM Fas 0/0 S6 Fas 0/24 153 R S I WS-C3550-2Fas 0/24 S5#sh run int         int fa 0/4 FastEthernet0/4 is down, line protocol is down (notconnect) Hardware is Fast Ethernet, address is 0013.80cf.ce04 (bia 0013.80cf.ce04) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Auto-duplex, Auto-speed, media type is 100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts (0 multicast) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 0 packets output, 0 bytes, 0 underruns --More--   S5# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 172 R S 2611XM Fas 0/1 R1 Fas 0/1 140 R 2611 Eth 0/1 R7 Fas 0/7 172 R S 2611XM Fas 0/1 R4 Fas 0/4 139 R 3620 Fas 0/0 S5 Fas 0/24 166 R S I WS-C3550-2Fas 0/24 S6# RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#int fa        config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0./  /24 S5(config-if)#int fa 0/24mls qos trust dscp int fa 0/4 mls qos trust dscp S5(config-if)#^Z S5# 1d04h: %SYS-5-CONFIG_I: Configured from console by console S5# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#sh pol int fa 0/010000000 20.10.1.1ping  Protocol [ip]: Target IP address: pingsh pol int fa 0/010000000 20.10.1.1 Repeat count [5]: 20.10.1.1ping sh pol int fa 0/010000000  Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 10000000, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!! RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 33 packets, 3432 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 38/3952 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 581 packets, 57284 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 114 packets, 11856 bytes 5 minute offered rate 2000 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 125/13000 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 583 packets, 57392 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 735 packets, 76440 bytes 5 minute offered rate 8000 bps, drop rate 0 bps Match: dscp af31 Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 752/78208 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 596 packets, 58384 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#q  RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#sh mls w qos ? aggregate-policer Show aggregate-policer information interface Show interface information maps Show mapping information | Output modifiers S5#sh mls qos map S5#sh mls qos maps ? cos-dscp Show COS to DSCP map dscp-cos Show DSCP to COS map dscp-mutation Show dscp-mutation map dscp-switch-priority Show DSCP to switch priority map ip-prec-dscp Show IP precedence to DSCP map policed-dscp Show DSCP to policed mark down DSCP map | Output modifiers S5#sh mls qos maps Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Default DSCP Mutation Map: --More--   S5#sh run int fa 0/24 Building configuration... Current configuration : 115 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk mls qos trust dscp end S5# S5# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b class class-map match-all dscp26 match dscp af31 class-map match-all telnet match protocol telnet class-map match-all dscp12 match dscp af12 class-map match-all dscp18 match dscp af21 class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 policy-map Prob18 class FTP shape average 256000 class telnet --More--   shape average 56000 class class-default police cir 512000 pir 600000 policy-map Prob22 class dscp12 bandwidth percent 15 class dscp18 bandwidth percent 15 class dscp26 bandwidth percent 50 ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 100 ! interface BRI0/0 --More--   no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 service-policy output Prob18 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 --More--   ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 80 service-policy output Prob22 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown --More--   R3#