=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2005.10.11 13:03:30 =~=~=~=~=~=~=~=~=~=~=~= R7> R7>en R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#interface FastEthernet0/0 R7(config-if)# ip address 180.40.7.133 255.255.255.224 R7(config-if)# speed auto R7(config-if)# duplex auto R7(config-if)# no shutdown R7(config-if)#! R7(config-if)#interface BRI0/0 R7(config-if)# no ip address R7(config-if)# shutdown R7(config-if)#! R7(config-if)#interface FastEthernet0/1 R7(config-if)# no ip address R7(config-if)# shutdown R7(config-if)# speed auto R7(config-if)# duplex auto R7(config-if)#! R7(config-if)#interface Serial1/0 R7(config-if)# ip address 180.40.7.68 255.255.255.224 R7(config-if)# encapsulation frame-relay R7(config-if)# ip ospf network point-to-multipoint R7(config-if)# frame-relay map ip 180.40.7.66 703 broadcast R7(config-if)# no shutdown R7(config-if)#! R7(config-if)#interface Serial1/1 R7(config-if)# no ip address R7(config-if)# shutdown R7(config-if)#! R7(config-if)#interface Serial1/2 R7(config-if)# no ip address R7(config-if)# shutdown R7(config-if)#! R7(config-if)#interface Serial1/3 R7(config-if)# no ip address R7(config-if)# shutdown R7(config-if)#! R7(config-if)#interface Serial1/4 R7(config-if)# no ip address R7(config-if)# shutdown R7(config-if)#! R7(config-if)#interface Serial1/5 R7(config-if)# no ip address R7(config-if)# shutdown R7(config-if)#! R7(config-if)#interface Serial1/6 R7(config-if)# no ip address R7(config-if)# shutdown R7(config-if)#! R7(config-if)#interface Serial1/7 R7(config-if)# no ip address R7(config-if)# shutdown R7(config-if)#! R7(config-if)#router ospf 1 R7(config-router)# log-adjacency-changes R7(config-router)# network 0.0.0.0 255.255.255.255 area 0 R7(config-router)#! R7(config-router)#ip http server R7(config)# *Mar 1 01:17:45.664: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down *Mar 1 01:17:45.668: %LINK-3-UPDOWN: Interface BRI0/0:2, changed state to down *Mar 1 01:17:46.669: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1, changed state to down *Mar 1 01:17:46.669: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:2, changed state to downno ip http secure-server R7(config)#ip classless R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#! R7(config)#call rsvp-sync R7(config)#! R7(config)#! R7(config)#mgcp profile default R7(config-mgcp-profile)#! R7(config-mgcp-profile)#! R7(config-mgcp-profile)#! R7(config-mgcp-profile)#dial-peer cor custom R7(config-dp-cor)#! R7(config-dp-cor)#! R7(config-dp-cor)#! R7(config-dp-cor)#! R7(config-dp-cor)#! R7(config-dp-cor)#line con 0 R7(config-line)# exec-timeout 0 0 R7(config-line)# logging synchronous R7(config-line)#line aux 0 R7(config-line)#line vty 0 4 R7(config-line)# *Mar 1 01:17:47.523: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 01:17:48.128: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up *Mar 1 01:17:48.524: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R7(config-line)# *Mar 1 01:17:59.130: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up R7(config-line)#int fa 0/0 R7(config-if)#no shut       ^Z R7# *Mar 1 01:18:14.619: %SYS-5-CONFIG_I: Configured from console by console R7# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 0/0 ^ % Invalid input detected at '^' marker. R3(config)#int s 0/0/0 1/0 R3(config-if)#fram map op    ip 180.40.7.68 307 bro R3(config-if)#^Z R3# *Mar 1 01:18:57.193: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 01:19:22.771: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.133 on Serial1/0 from LOADING to FULL, Loading Done R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip int brief Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES manual up up ATM1/0 unassigned YES unset administratively down down Virtual-Access1 unassigned YES unset up up R4#conif g Translating "conif" Translating "conif" % Unknown command or computer name, or unable to find computer address R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 20.0.0.0/24 is subnetted, 1 subnets O 20.10.1.0 [110/66] via 180.40.7.131, 00:05:47, FastEthernet0/0 O 208.28.1.0/24 [110/11] via 180.40.7.131, 00:05:47, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 8 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/65] via 180.40.7.131, 00:05:47, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:05:47, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:05:47, FastEthernet0/0 O 180.40.7.67/32 [110/65] via 180.40.7.131, 00:05:48, FastEthernet0/0 O 180.40.7.66/32 [110/1] via 180.40.7.129, 00:05:48, FastEthernet0/0 O 180.40.7.65/32 [110/1] via 180.40.7.131, 00:05:48, FastEthernet0/0 O 180.40.7.68/32 [110/782] via 180.40.7.129, 00:05:48, FastEthernet0/0 R4(config)#do sh ip route     preoto    otoco Routing Protocol is "ospf 1" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Router ID 180.40.7.130 Number of areas in this router is 1. 1 normal 0 stub 0 nssa Maximum path: 4 Routing for Networks: 0.0.0.0 255.255.255.255 area 0 Routing Information Sources: Gateway Distance Last Update 180.40.7.130 110 00:05:57 180.40.7.129 110 00:05:57 180.40.7.133 110 00:05:57 180.40.7.162 110 00:05:57 208.28.1.1 110 00:05:57 208.28.1.2 110 00:05:57 Distance: (default is 110) R4(config)#int lo 0 R4(config-if)#ip addrss  ess 100.1.1.1 255.255.255.0 R4(config-if)#ip address 100.1.1.1 255.255.255.0nt lo 0 do sh ip protoco Routing Protocol is "ospf 1" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Router ID 180.40.7.130 Number of areas in this router is 1. 1 normal 0 stub 0 nssa Maximum path: 4 Routing for Networks: 0.0.0.0 255.255.255.255 area 0 Routing Information Sources: Gateway Distance Last Update 180.40.7.130 110 00:06:32 180.40.7.129 110 00:06:32 180.40.7.133 110 00:06:32 180.40.7.162 110 00:06:32 208.28.1.1 110 00:06:32 208.28.1.2 110 00:06:32 Distance: (default is 110) R4(config-if)# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#sh access % Ambiguous command: "sh access" R3#sh access-l;  R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#access-list 100 per ip   cmp host 100.1.1.1 host 20.10.1.2 echo R3(config)#access-list 100 per icmp host 100.1.1.1 host 20.10.1.2 echo-r R3(config)#access-list 100 per icmp host 100.1.1.1 host 20.10.1.2 echo-reply R3(config)#do sh access-list Extended IP access list 100 10 permit icmp host 100.1.1.1 host 20.10.1.2 echo 20 permit icmp host 100.1.1.1 host 20.10.1.2 echo-reply R3(config)# R3(config)# R3(config)# R3(config)# R3(config)# R3(config)#ip access0 -k list ex 100 R3(config-ext-nacl)#no 20 R3(config-ext-nacl)#no 20ip access-list ex 100do sh access-list $ 100 per icmp host 100.1.1.1 host 20.10.1.2 echo-reply do sh access-list  Extended IP access list 100 10 permit icmp host 100.1.1.1 host 20.10.1.2 echo R3(config-ext-nacl)#exit R3(config)#access-list 101 per icmp host 100.1.1.1 20.10.1.1h20.10.1.1o20.10.1.1s20.10.1.1t20.10.1.1 20.10.1.120.10.1.1 ex cho R3(config)#access-list 101 per icmp host 100.1.1.1 host 20.10.1.1 echo echo 0 echo echo0 echo. echo0 echo. echo0 echo. echo2 echo5 echo5 ec$ 20.10.1.0 0.0.0.255 echo 20.10.1.0 0.0.0.255 echo  20.10.1.0 0.0.0.255 echo  20.10.1.0 0.0.0.255 echo  per icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo 2 per icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo R3(config)#route-map Prob1 10 R3(config-route-map)#match ip add 100 R3(config-route-map)#mat le R3(config-route-map)#mat length ? <0-2147483647> Minimum packet length R3(config-route-map)#mat length 0 1000    ? <0-2147483647> Maximum packet length R3(config-route-map)#mat length 0 1000 R3(config-route-map)#set ip ne R3(config-route-map)#set ip next-hop ? A.B.C.D IP address of next hop peer-address Use peer address (for BGP only) verify-availability Verify if nexthop is a CDP neighbor R3(config-route-map)#set ip next-hop 180.40.7.67 ? A.B.C.D IP address of next hop R3(config-route-map)#set ip next-hop 180.40.7.67 R3(config-route-map)#set ip next-hop 180.40.7.67 mat length 0 1000 ch ip add 100 route-map Prob1 10  20 R3(config-route-map)#match ip add 101 R3(config-route-map)#set int R3(config-route-map)#set interface s R3(config-route-map)#set interface serial 1/2 R3(config-route-map)#set interface serial 1/2match ip add 101 route-map Prob1 20  30 R3(config-route-map)#s match ip add 102 R3(config-route-map)#match le R3(config-route-map)#match length 1001 ? <0-2147483647> Maximum packet length R3(config-route-map)#match length 1001 214   0-21474836472147483647 2147483647  R3(config-route-map)#set int s 1/2 R3(config-route-map)#int fa 0/0 R3(config-if)#ip pol R3(config-if)#ip policy royu R3(config-if)#ip policy royu  u R3(config-if)#ip policy route-map Prob1 ? R3(config-if)#ip policy route-map Prob1   R3(config-if)#^Z R3#sh *Mar 1 01:40:37.609: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip poli Interface Route map Fa0/0 Prob1 R3# R3# R3#sh ip poli ? | Output modifiers R3#sh ip poli            deb ip pol Policy routing debugging is on R3#sh log Syslog logging: enabled (0 messages dropped, 12 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 43 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: disabled, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 59 message lines logged R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#log buff R3(config)#^Z R3# *Mar 1 01:40:59.721: %SYS-5-CONFIG_I: Configured from console by console R3#h ip ropute    ute help ip route ^ % Invalid input detected at '^' marker. R3#h ip routesh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:15:01, FastEthernet0/0 20.0.0.0/24 is subnetted, 1 subnets O 20.10.1.0 [110/66] via 180.40.7.131, 00:15:01, FastEthernet0/0 O 208.28.1.0/24 [110/11] via 180.40.7.131, 00:15:01, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 8 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/65] via 180.40.7.131, 00:15:01, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:15:02, FastEthernet0/0 C 180.40.7.0/27 is directly connected, Serial1/2 O 180.40.7.67/32 [110/65] via 180.40.7.131, 00:15:02, FastEthernet0/0 O 180.40.7.65/32 [110/1] via 180.40.7.131, 00:15:02, FastEthernet0/0 C 180.40.7.64/27 is directly connected, Serial1/0 --More--   R3# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 20  0/0.1 R1(config-subif)#band 128 R1(config-subif)#band 128int s 0/0.1 2 R1(config-subif)#int s 0/0.2band 128  R1(config-subif)# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#sh int s 1/2 Serial1/2 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is 180.40.7.1/27 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 1359 packets input, 105272 bytes, 0 no buffer Received 710 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 1360 packets output, 105052 bytes, 0 underruns 0 output errors, 0 collisions, 3 interface resets 0 output buffer failures, 0 output buffers swapped out --More--   R3# RACK18AS> [Resuming connection 3 to r3 ... ] R3# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1(config-subif)#do sh int s 0/0 Serial0/0 is up, line protocol is up Hardware is PowerQUICC Serial MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 616, LMI stat recvd 617, LMI upd recvd 0, DTE LMI up LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 625/0, interface broadcasts 410 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 01:42:44 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1158 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 1240 packets input, 91835 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles --More--   R1(config-subif)# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:00:23, FastEthernet0/0 20.0.0.0/24 is subnetted, 1 subnets O 20.10.1.0 [110/782] via 180.40.7.2, 00:00:23, Serial1/2 [110/782] via 180.40.7.67, 00:00:23, Serial1/0 O 208.28.1.0/24 [110/11] via 180.40.7.131, 00:00:23, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 8 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.2, 00:00:25, Serial1/2 [110/781] via 180.40.7.67, 00:00:25, Serial1/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:00:25, FastEthernet0/0 C 180.40.7.0/27 is directly connected, Serial1/2 O 180.40.7.67/32 [110/781] via 180.40.7.2, 00:00:25, Serial1/2 --More--   R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] R4(config-if)#^Z R4#sh ip ou *Mar 1 01:44:38.031: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip ou  route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 1 subnets O 20.10.1.0 [110/783] via 180.40.7.131, 00:00:38, FastEthernet0/0 [110/783] via 180.40.7.129, 00:00:38, FastEthernet0/0 O 208.28.1.0/24 [110/11] via 180.40.7.131, 00:00:38, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 8 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.131, 00:00:39, FastEthernet0/0 [110/782] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:00:39, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.67/32 [110/782] via 180.40.7.131, 00:00:39, FastEthernet0/0 --More--   [110/782] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.66/32 [110/1] via 180.40.7.129, 00:00:41, FastEthernet0/0 O 180.40.7.65/32 [110/1] via 180.40.7.131, 00:00:41, FastEthernet0/0 O 180.40.7.68/32 [110/782] via 180.40.7.129, 00:00:41, FastEthernet0/0 R4#ping 20.10.1.1 2 sou R4#ping 20.10.1.2 source 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/46/48 ms R4#x RACK18AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh ip    log Syslog logging: enabled (0 messages dropped, 12 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 58 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 15 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 60 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 01:40:59.721: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 01:42:57.129: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match *Mar 1 01:42:57.129: IP: route map Prob1, item 10, permit *Mar 1 01:42:57.129: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed *Mar 1 01:42:57.133: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 *Mar 1 01:42:57.226: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match *Mar 1 01:42:57.226: IP: route map Prob1, item 10, permit *Mar 1 01:42:57.226: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed *Mar 1 01:42:57.226: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 R3# R3# R3# R3# R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] % Ambiguous command: "x" R4# R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#clea log Clear logging buffer [confirm] R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] R4#ping Protocol [ip]: Target IP address: 1 20.10.1.2 Repeat count [5]: Datagram size [100]: 1500  00 Timeout in seconds [2]: Extended commands [n]: y Source address or interface: 100.1.1.1 Type of service [0]: Set DF bit in IP header? [no]: Validate reply data? [no]: Data pattern [0xABCD]: Loose, Strict, Record, Timestamp, Verbose[none]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 5, 1500-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!! RACK18AS>3 [Resuming connection 3 to r3 ... ] *M R3# *Mar 1 01:44:04.628: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1500, policy match *Mar 1 01:44:04.628: IP: route map Prob1, item 30, permit *Mar 1 01:44:04.628: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1500, policy routed *Mar 1 01:44:04.628: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] ! Succ R4#100.1.1.1y 150020.10.1.2ping  Protocol [ip]: Target IP address: 20.10.1.1 Repeat count [5]: Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/48/64 ms R4# R4# R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] * R3#sh log Syslog logging: enabled (0 messages dropped, 12 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 85 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 42 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 60 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 01:44:01.948: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1500, policy match *Mar 1 01:44:01.948: IP: route map Prob1, item 30, permit *Mar 1 01:44:01.948: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1500, policy routed *Mar 1 01:44:01.952: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 01:44:03.290: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1500, policy match *Mar 1 01:44:03.290: IP: route map Prob1, item 30, permit *Mar 1 01:44:03.290: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1500, policy routed *Mar 1 01:44:03.290: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 01:44:04.628: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1500, policy match *Mar 1 01:44:04.628: IP: route map Prob1, item 30, permit *Mar 1 01:44:04.628: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1500, policy routed *Mar 1 01:44:04.628: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 01:44:34.673: IP: s=180.40.7.130 (FastEthernet0/0), d=20.10.1.1 (Serial1/0), len 100, policy rejected -- normal forwarding --More--  *Mar 1 01:44:34.781: IP: s=180.40.7.130 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy rejected -- normal forwarding R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] R4#20.10.1.1ping 100.1.1.1y 150020.10.1.2ping x ping 20.10.1.2 source 100.1.1.1 source 100.1.1.1 1 source 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/43/60 ms R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ;lo   log Syslog logging: enabled (0 messages dropped, 12 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 106 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 63 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 60 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 01:44:01.948: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1500, policy match *Mar 1 01:44:01.948: IP: route map Prob1, item 30, permit *Mar 1 01:44:01.948: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1500, policy routed *Mar 1 01:44:01.952: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 01:44:03.290: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1500, policy match *Mar 1 01:44:03.290: IP: route map Prob1, item 30, permit *Mar 1 01:44:03.290: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1500, policy routed *Mar 1 01:44:03.290: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 01:44:04.628: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1500, policy match *Mar 1 01:44:04.628: IP: route map Prob1, item 30, permit *Mar 1 01:44:04.628: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1500, policy routed *Mar 1 01:44:04.628: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 01:44:34.673: IP: s=180.40.7.130 (FastEthernet0/0), d=20.10.1.1 (Serial1/0), len 100, policy rejected -- normal forwarding --More--  *Mar 1 01:44:34.781: IP: s=180.40.7.130 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy rejected -- normal forwarding *Mar 1 01:45:21.382: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 01:45:21.386: IP: route map Prob1, item 20, permit *Mar 1 01:45:21.386: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 01:45:21.386: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 01:45:21.478: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 01:45:21.478: IP: route map Prob1, item 20, permit *Mar 1 01:45:21.478: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 01:45:21.478: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 01:45:21.570: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 01:45:21.570: IP: route map Prob1, item 20, permit *Mar 1 01:45:21.574: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 01:45:21.574: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 R3#    sh run        u all All possible debugging has been turned off R3#sh u run Building configuration... Current configuration : 2109 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R3 ! logging queue-limit 100 logging buffered 4096 debugging ! ip subnet-zero ! ! no ip domain lookup ! ip audit notify log ip audit po max-events 100 mpls ldp logging neighbor-changes ! ! --More--  ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto --More--   speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 301 broadcast frame-relay map ip 180.40.7.67 302 broadcast frame-relay map ip 180.40.7.68 307 broadcast ! interface Serial1/1 no ip address shutdown --More--  ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown --More--  ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless ! ! ! access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo ! route-map Prob1 permit 10 match ip address 100 match length 0 1000 set ip next-hop 180.40.7.67 ! route-map Prob1 permit 20 match ip address 101 set interface Serial1/2 --More--  ! --More--  route-map Prob1 permit 30 --More--   match ip address 102 --More--   match length 1001 2147483647 --More--   set interface Serial1/2 --More--  ! --More--  ! --More--  call rsvp-sync --More--  ! --More--   R3# R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] R4#sh run int lo 0-  Building configuration... Current configuration : 63 bytes ! interface Loopback0 ip address 100.1.1.1 255.255.255.0 end R4# R4# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip cef R3(config)#^Z R3# *Mar 1 01:51:49.486: %SYS-5-CONFIG_I: Configured from console by console R3# RACK18AS> [Resuming connection 3 to r3 ... ] R3#sh run | i ip cef ip cef R3# R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#do shg    h access-list R4(config)#access-list 100 per icmp any any echo R4(config)#ip loca R4(config)#ip local po R4(config)#ip local pol R4(config)#ip local policy ? route-map Policy route map R4(config)#ip local policy                 route-map Prob3 10 R4(config-route-map)#match ip add 100 R4(config-route-map)#net R4(config-route-map)#net   set net e xt   R4(config-route-map)#set next- R4(config-route-map)#set next-h R4(config-route-map)#set next-h      ? as-path Prepend string for a BGP AS-path attribute automatic-tag Automatically compute TAG value comm-list set BGP community list (for deletion) community BGP community attribute dampening Set BGP route flap dampening parameters default Set default information extcommunity BGP extended community attribute interface Output interface ip IP specific information ipv6 IPv6 specific information level Where to import route local-preference BGP local preference path attribute metric Metric value for destination routing protocol metric-type Type of metric for destination routing protocol mpls-label Set MPLS label for prefix nlri BGP NLRI type origin BGP origin code tag Tag value for destination routing protocol traffic-index BGP traffic classification number for accounting weight BGP weight for routing table R4(config-route-map)#set q ip nex R4(config-route-map)#set ip next-hop ? A.B.C.D IP address of next hop peer-address Use peer address (for BGP only) verify-availability Verify if nexthop is a CDP neighbor R4(config-route-map)#set ip next-hop 180.40.7.129 R4(config-route-map)#exit R4(config)#ip loca pol R4(config)#ip loca policy route R4(config)#ip loca policy route-map Prob2 3 R4(config)#^Z R4# *Mar 1 01:59:13.607: %SYS-5-CONFIG_I: Configured from console by console R4#ping 20.101.  .1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 48/58/64 ms R4#sh access-list Extended IP access list 100 10 permit icmp any any echo (5 matches) R4#\ deb ip pol Policy routing debugging is on R4#deb ip polsh access-listping 20.10.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/52/64 ms R4# *Mar 1 01:59:39.755: IP: s=180.40.7.130 (local), d=20.10.1.1, len 100, policy match *Mar 1 01:59:39.755: IP: route map Prob3, item 10, permit *Mar 1 01:59:39.755: IP: s=180.40.7.130 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 01:59:39.755: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 01:59:39.803: IP: s=180.40.7.130 (local), d=20.10.1.1, len 100, policy match *Mar 1 01:59:39.803: IP: route map Prob3, item 10, permit *Mar 1 01:59:39.803: IP: s=180.40.7.130 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 01:59:39.803: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 01:59:39.867: IP: s=180.40.7.130 (local), d=20.10.1.1, len 100, policy match *Mar 1 01:59:39.867: IP: route map Prob3, item 10, permit *Mar 1 01:59:39.867: IP: s=180.40.7.130 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 01:59:39.867: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 01:59:39.915: IP: s=180.40.7.130 (local), d=20.10.1.1, len 100, policy match *Mar 1 01:59:39.915: IP: route map Prob3, item 10, permit *Mar 1 01:59:39.915: IP: s=180.40.7.130 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 01:59:39.915: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 01:59:39.975: IP: s=180.40.7.130 (local), d=20.10.1.1, len 100, policy match *Mar 1 01:59:39.975: IP: route map Prob3, item 10, permit *Mar 1 01:59:39.975: IP: s=180.40.7.130 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 01:59:39.979: IP: local to FastEthernet0/0 180.40.7.129 R4# R4#sh      ping       RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#clea log Clear logging buffer [confirm] R3# RACK18AS>3 4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.1 sou 100.1.1.1.  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/40/48 ms R4# *Mar 1 02:01:17.399: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100, policy match *Mar 1 02:01:17.399: IP: route map Prob3, item 10, permit *Mar 1 02:01:17.399: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 02:01:17.399: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 02:01:17.447: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100, policy match *Mar 1 02:01:17.447: IP: route map Prob3, item 10, permit *Mar 1 02:01:17.447: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 02:01:17.451: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 02:01:17.483: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100, policy match *Mar 1 02:01:17.483: IP: route map Prob3, item 10, permit *Mar 1 02:01:17.483: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 02:01:17.483: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 02:01:17.531: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100 R4#, policy match *Mar 1 02:01:17.531: IP: route map Prob3, item 10, permit *Mar 1 02:01:17.531: RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#sh log Syslog logging: enabled (0 messages dropped, 12 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 107 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 64 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 61 message lines logged --More--   Log Buffer (4096 bytes): R3# sh log Syslog logging: enabled (0 messages dropped, 12 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 107 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 64 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 61 message lines logged --More--   R3#deb ip pol Policy routing debugging is on R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] 00.1.1.1 (local), d=20.10 R4#ping 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/40/48 ms R4# *Mar 1 02:01:34.331: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100, policy match *Mar 1 02:01:34.331: IP: route map Prob3, item 10, permit *Mar 1 02:01:34.331: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 02:01:34.331: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 02:01:34.367: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100, policy match *Mar 1 02:01:34.367: IP: route map Prob3, item 10, permit *Mar 1 02:01:34.367: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 02:01:34.367: IP: RACK18AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 R3#sh log Syslog logging: enabled (0 messages dropped, 12 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 132 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 89 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 61 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 01:59:27.669: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 01:59:27.669: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed *Mar 1 01:59:27.705: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 01:59:27.705: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed *Mar 1 01:59:27.753: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 01:59:27.753: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed *Mar 1 01:59:27.789: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 01:59:27.789: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed *Mar 1 01:59:27.837: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 01:59:27.837: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed R3#  u all All possible debugging has been turned off R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] 0/0 180.40.7.129 *Mar 1 02:01:34.415 R4#u all All possible debugging has been turned off R4#sh run | b ip local ip local policy route-map Prob3 no ip http server ip classless ! ! ! access-list 100 permit icmp any any echo ! route-map Prob3 permit 10 match ip address 100 set ip next-hop 180.40.7.129 ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 --More--   R4# RACK18AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0 R2(config-if)#.1  int s 1/0.1 R2(config-subif)#tra R2(config-subif)#traffic-shape ? adaptive Enable Traffic Shaping adaptation to BECN fecn-adapt Enable Traffic Shaping reflection of FECN as BECN group configure token bucket: group CIR (bps) [Bc (bits) [Be (bits)]] rate configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]] R2(config-subif)#traffic-shape               exit R2(config)#exitint s 1/0.1 .1 R2(config-subif)#int s 1/0.1   R2(config-if)#traf R2(config-if)#traffic-shape rate 64000 R2(config-if)#traffic-shape rate 64000       ? <8000-100000000> Target Bit Rate (bits per second) R2(config-if)#traffic-shape rate 64                     do sh run   tra R2(config-if)#do sh tra % Ambiguous command: "sh tra" R2(config-if)#^Z R2#sh tra *Mar 1 02:03:43.028: %SYS-5-CONFIG_I: Configured from console by console R2#sh traff R2#sh traffic-shape Interface Se1/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 - R2# R2# R2# R2# R2# R2# R2# R2#int     config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0 R2(config-if)#int s 1/0do sh tratraffic-shape rate 64000ntraffic-shape rate 64000otraffic-shape rate 64000 traffic-shape rate 64000 R2(config-if)#int s 1/0.1 R2(config-subif)#int s 1/0.1no traffic-shape rate 64000int s 1/0 do sh tratraffic-shape rate 64000 R2(config-subif)#int traffic-shape rate 64000int s 1/0.1  2 R2(config-subif)#int s 1/0.2traffic-shape rate 64000 R2(config-subif)#^Z R2#sh *Mar 1 02:04:37.529: %SYS-5-CONFIG_I: Configured from console by console R2#sh tra % Ambiguous command: "sh tra" R2# R2#sh traf Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 - Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 - R2#sh run | b interface Serial 1/01/0  interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 8000 8000 1000 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 8000 8000 1000 frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clockrate 64000 --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)#no int s 1/0.1traffic-shape rate 64000ntraffic-shape rate 64000otraffic-shape rate 64000 traffic-shape rate 64000 R2(config-subif)#no traffic-shape rate 64000int s 1/0.1  2 R2(config-subif)#int s 1/0.2no traffic-shape rate 64000 R2(config-subif)#exit R2(config)#map-class ? atm Asynchronous transfer mode dialer Dial on Demand frame-relay Frame Relay R2(config)#map-class fram ? WORD Static map class name R2(config)#map-class fram Prob4 ? R2(config)#map-class fram Prob4 R2(config-map-class)#? Static maps class configuration commands: default Set a command to its defaults exit-class Exit from static map class configuration mode frame-relay Configure Map parameters help Description of the interactive help system no Negate a command or set its defaults service-policy class-based service policy R2(config-map-class)#fram > ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 56000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R2(config-map-class)#fram cir ? <1-45000000> Applied to both Incoming/Outgoing CIR, Bits per second in Incoming CIR out Outgoing CIR R2(config-map-class)#fram cir 64000 R2(config-map-class)#exit R2(config)#int s 1/0.1 R2(config-subif)#? Interface configuration commands: appletalk Appletalk interface subcommands arp Set arp type (arpa, probe, snap) or timeout backup Modify backup parameters bandwidth Set bandwidth informational parameter bgp-policy Apply policy propogated by bgp community string bridge-group Transparent bridging interface parameters cdp CDP interface subcommands clns CLNS interface subcommands crypto Encryption/Decryption commands decnet Interface DECnet config commands default Set a command to its defaults delay Specify interface throughput delay description Interface specific description dlsw DLSw Interface Subcommands dspu Down Stream PU dxi ATM-DXI configuration commands exit Exit from interface configuration mode frame-relay Set frame relay parameters fras DLC Switch Interface Command h323-gateway Configure H323 Gateway ip Interface Internet Protocol config commands --More--   ipv6 IPv6 interface subcommands ipx Novell/IPX interface subcommands isis IS-IS commands iso-igrp ISO-IGRP interface subcommands keepalive Enable keepalive lat LAT commands llc2 LLC2 Interface Subcommands map-group Configure static map group mpls Configure MPLS interface parameters mtu Set the interface Maximum Transmission Unit (MTU) multiring Enable RIF usage for a routable protocol netbios Use a defined NETBIOS access list or enable name-caching no Negate a command or set its defaults ntp Configure NTP pulse-time Force DTR low during resets rate-limit Rate Limit service-policy Configure QoS Service Policy shutdown Shutdown the selected interface smds Modify SMDS parameters sna SNA pu configuration snapshot Configure snapshot support on the interface source-bridge Configure interface for source-route bridging tag-switching Tag Switching interface configuration commands --More--   R2(config-subif)#map R2(config-subif)#map-group ? WORD Static map group name R2(config-subif)#map-group           f fram ? class Define a map class on the interface de-group Associate a DE group with a DLCI interface-dlci Define a DLCI on an interface/subinterface inverse-arp Enable/disable FR inverse ARP ip Frame Relay Internet Protocol config commands map Map a protocol address to a DLCI address payload-compression Use payload compression priority-dlci-group Define a priority group of DLCIs vc-bundle configure a frame-relay vc-bundle R2(config-subif)#fram map ? appletalk AppleTalk bridge Bridging bstun Block Serial Tunnel clns ISO CLNS decnet DECnet dlsw Data Link Switching ip IP ipv6 IPV6 ipx Novell IPX llc2 llc2 pppoe PPP over Ethernet qllc qllc protocol rsrb Remote Source-Route Bridging stun Serial Tunnel R2(config-subif)#fram map      class        class ? WORD map class name R2(config-subif)#fram class Prob4 ? R2(config-subif)#fram class Prob4 R2(config-subif)#efram class Prob4 int s 1/0.1  2 R2(config-subif)#do sh run int s 1/0.2 Building configuration... Current configuration : 157 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 201 end R2(config-subif)#frame-relay interface-dlci 201 %PVC is already defined R2(config-fr-dlci)# R2(config-fr-dlci)# R2(config-fr-dlci)# R2(config-fr-dlci)#? Frame Relay dlci configuration commands: auto Configure Automation class Assign a mapclass to a dlci default Set a command to its defaults exit Exit from FR dlci configuration mode load-interval Specify interval for load calculation for a dlci no Negate a command or set its defaults vofr Voice over Frame-Relay R2(config-fr-dlci)#class ? WORD map class name R2(config-fr-dlci)#class Prob4 R2(config-fr-dlci)#^Z R2#sh *Mar 1 02:09:23.883: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b int  config t sh run | b interface Serial1/0 interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint frame-relay class Prob4 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 201 class Prob4 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clockrate 64000 --More--   R2#sh fra     traff R2#sh traff R2#sh traffic-shape R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa 0/      s 1? % Unrecognized command R2(config)#ints 10 /0 ^ % Invalid input detected at '^' marker. R2(config)#ints 1/0 ts 1/0 ^ % Invalid input detected at '^' marker. R2(config)#int s 1/0 R2(config-if)# R2(config-if)# R2(config-if)# R2(config-if)# R2(config-if)#fram tr R2(config-if)#fram traf R2(config-if)#fram traffic-shaping ? R2(config-if)#fram traffic-shaping R2(config-if)#^Z R2# *Mar 1 02:10:55.088: %SYS-5-CONFIG_I: Configured from console by console R2#config tsh traffic-shape  ic-shape Interface Se1/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 207 56000 875 7000 0 125 875 - Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 203 64000 1000 64000 0 125 1000 - Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 201 64000 1000 64000 0 125 1000 - R2# R2# R2# R2# R2# R2#fram      sh ff ram map Serial1/0.1 (up): point-to-point dlci, dlci 203(0xCB,0x30B0), broadcast status defined, active Serial1/0.2 (up): point-to-point dlci, dlci 201(0xC9,0x3090), broadcast status defined, active R2#sh run fram maptraffic-shape config t sh traffic-shape  run | b interface Serial1/0 interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint frame-relay class Prob4 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 201 class Prob4 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 --More--   ip address 180.40.7.2 255.255.255.224 clockrate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! --More--  router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless ! ! ! ! map-class frame-relay Prob4 frame-relay cir 64000 ! ! call rsvp-sync ! ! mgcp profile default ! ! ! dial-peer cor custom --More--   R2# R2#c on    config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#f map-class         map-class frame-relay Prob4 R2(config-map-class)#fram ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 56000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R2(config-map-class)#fram a R2(config-map-class)#fram adaptive-shaping ? becn Enable rate adjustment in response to BECN foresight Enable rate adjustment in response to ForeSight messages and BECN interface-congestion Enable rate adjustment depend on interface queue R2(config-map-class)#fram adaptive-shaping be R2(config-map-class)#fram adaptive-shaping becn ? R2(config-map-class)#fram adaptive-shaping becn R2(config-map-class)#fram min R2(config-map-class)#fram mincir 32000 R2(config-map-class)#^Z R2#sh run *Mar 1 02:21:19.576: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b f map  -class map-class frame-relay Prob4 frame-relay cir 64000 frame-relay mincir 32000 frame-relay adaptive-shaping becn ! ! call rsvp-sync ! ! mgcp profile default ! ! ! dial-peer cor custom ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#no fram mincir 32000adaptive-shaping becn map-class frame-relay Prob4nmap-class frame-relay Prob4omap-class frame-relay Prob4 map-class frame-relay Prob4 R2(config)#i dop  sh run int s 1/0.1 Building configuration... Current configuration : 156 bytes ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 203 end R2(config)#do sh run int s 1/0.1 2 Building configuration... Current configuration : 157 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 201 end R2(config)#in  int s 1/0 R2(config-if)#no fram tra % Ambiguous command: "no fram tra" R2(config-if)#no fram tra no fram traff R2(config-if)#int s 1/0.1 R2(config-subif)#traf R2(config-subif)#traffic-shape rat R2(config-subif)#traffic-shape rate 64000 ? <0-100000000> bits per interval, sustained R2(config-subif)#traffic-shape rate 64000 R2(config-subif)#traf R2(config-subif)#traffic-shape ? adaptive Enable Traffic Shaping adaptation to BECN fecn-adapt Enable Traffic Shaping reflection of FECN as BECN group configure token bucket: group CIR (bps) [Bc (bits) [Be (bits)]] rate configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]] R2(config-subif)#traffic-shape d R2(config-subif)#traffic-shape d? % Unrecognized command R2(config-subif)#traffic-shape d ad ? <1-100000000> Lower Bound Target Bit Rate (bits per second) R2(config-subif)#traffic-shape ad 32000 ? R2(config-subif)#traffic-shape ad 32000 R2(config-subif)#int s 1/02 R2(config-if)#int s 1/02 int s 1/02traffic-shape ad 32000 int s 1/02  .2 R2(config-subif)#int s 1/0.22 traffic-shape ad 32000 traffic shaping not enabled R2(config-subif)#traffic-shape ad 32000 int s 1/0.2 2 traffic-shape ad 32000 rate 64000 int s 1/0.1 traffic-shape rate 64000 R2(config-subif)#traffic-shape rate 64000 ad 32000  R2(config-subif)#^Z R2#sh *Mar 1 02:24:14.835: %SYS-5-CONFIG_I: Configured from console by console R2#sh f traff Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 BECN Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 BECN R2#sh traff ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-FrameRelay Virtual Frame Relay interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing queue Show shaping queue contents statistics traffic rate shaping statistics | Output modifiers R2#sh traff in  s 1/0,.1   .1 % Ambiguous command: "sh traff s 1/0.1" R2#sh traff s 1/0.1es 1/0.1rs 1/0.1s 1/0.1 ser 1/0.1 Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 2000 8000 8000 125 1000 BECN R2#sh run | b int s  erface Serial1/0 interface Serial1/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 8000 8000 1000 traffic-shape adaptive 32000 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 8000 8000 1000 traffic-shape adaptive 32000 frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! --More--   R2# R2# R2# R2# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1(config-subif)#^Z R1# *Mar 1 02:27:46.121: %SYS-5-CONFIG_I: Configured from console by console R1#sh access % Ambiguous command: "sh access" R1#sh access-list R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#access-list 100 p[er   er te cp host 208.28.1.2 any eq telnet R1(config)#access-list 100 per tcp host 208.28.1.2 any eq telnet         00 per tcp host 208.28.1.2 any p host 208.28.1.2 any ip host 208.28.1.2 any t 100 per ip host 208.28.1.2 any 1 per ip host 208.28.1.2 any  R1(config)#class-map S5Teletn   net R1(config-cmap)#match ip  R1(config-cmap)#match ip add R1(config-cmap)#match ip add      ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R1(config-cmap)#match ace R1(config-cmap)#match ace ce R1(config-cmap)#match access-group 100 R1(config-cmap)#match access-group 100class-map S5Telnet access-list 101 per ip host 208.28.1.2 any class-map S5Telnet       OtherStuff R1(config-cmap)#match acces 101 R1(config-cmap)#exit R1(config)#polu i   R1(config)#policy-map Prob6 R1(config-pmap)#class S5Telnet R1(config-pmap-c)#band R1(config-pmap-c)#bandwidth ? <8-2000000> Kilo Bits per second percent % of total Bandwidth remaining % of the remaining bandwidth R1(config-pmap-c)#bandwidth 1000 R1(config-pmap-c)#exit R1(config-pmap)#class S5OtherStuff R1(config-pmap-c)#band 5000 R1(config-pmap-c)#band 5000nband 5000oband 5000 band 5000 R1(config-pmap-c)#pol R1(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R1(config-pmap-c)#police 50000  0000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R1(config-pmap-c)#police 5000000 con R1(config-pmap-c)#police 5000000 conform-action ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R1(config-pmap-c)#police 5000000 conform-action tr R1(config-pmap-c)#police 5000000 conform-action transmit ? exceed-action action when rate is within conform and conform + exceed burst R1(config-pmap-c)#police 5000000 conform-action transmit ex R1(config-pmap-c)#police 5000000 conform-action transmit exceed-action ? drop drop packet set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R1(config-pmap-c)#police 5000000 conform-action transmit exceed-action se R1(config-pmap-c)#police 5000000 conform-action transmit exceed-action set-p R1(config-pmap-c)#$m-action transmit exceed-action set-prec-transmit ? <0-7> new precedence R1(config-pmap-c)#$m-action transmit exceed-action set-prec-transmit 3 R1(config-pmap-c-police)#^Z R1# *Mar 1 02:36:51.792: %SYS-5-CONFIG_I: Configured from console by console R1#conif g Translating "conif" Translating "conif" % Unknown command or computer name, or unable to find computer address R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do sh run int     | poli sh run | poli ^ % Invalid input detected at '^' marker. R1(config)#do sh run | poli polii poli poli b poli poli policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint --More--   frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 180.40.7.131 255.255.255.224 half-duplex ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! --More--   R1(config)#int e 0/1 R1(config-if)#ser R1(config-if)#service-policy v R1(config-if)#service-policy v ? history Keep history of QoS metrics input Assign policy-map to the input of an interface output Assign policy-map to the output of an interface R1(config-if)#service-policy out ? WORD policy-map name R1(config-if)#service-policy out Prob6 R1(config-if)#^Z R1#sh *Mar 1 02:40:04.195: %SYS-5-CONFIG_I: Configured from console by console R1#sh poli int s e 0/1 Ethernet0/1 Service-policy output: Prob6 Class-map: S5Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 100 Queueing Output Queue: Conversation 265 Bandwidth 1000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: S5OtherStuff (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 101 police: cir 5000000 bps, bc 156250 bytes conformed 0 packets, 0 bytes; actions: transmit exceeded 0 packets, 0 bytes; actions: --More--   set-prec-transmit 3 --More--   conformed 0 bps, exceed 0 bps --More--   --More--   Class-map: class-default (match-any) --More--   2 packets, 158 bytes --More--   5 minute offered rate 0 bps, drop rate 0 bps --More--   Match: any R1# R1#sh run | b poli policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint --More--   frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output Prob6 half-duplex ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless --More--   R1#condfi   fig t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#pri R1(config)#prio R1(config)#priority-list 1 ? default Set priority queue for unspecified datagrams interface Establish priorities for packets from a named interface protocol priority queueing by protocol queue-limit Set queue limits for priority queues R1(config)#priority-list 1 pro R1(config)#priority-list 1 protocol ? arp IP ARP bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dlsw Data Link Switching ip IP ipv6 IPV6 ipx Novell IPX llc2 llc2 pad PAD links pppoe PPP over Ethernet qllc qllc protocol rsrb Remote Source-Route Bridging --More--   R1(config)#priority-list 1 protocol ip ? high medium normal low R1(config)#priority-list 1 protocol ip high ? fragments Prioritize fragmented IP packets gt Prioritize packets greater than a specified size list To specify an access list lt Prioritize packets less than a specified size tcp Prioritize TCP packets 'to' or 'from' the specified port udp Prioritize UDP packets 'to' or 'from' the specified port R1(config)#priority-list 1 protocol ip high tcp ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   R1(config)#priority-list 1 protocol ip high tcp telnet ? R1(config)#priority-list 1 protocol ip high tcp telnet R1(config)#p pre i R1(config)#prior R1(config)#priority-list 1 pro R1(config)#priority-list 1 protocol ip low tcp http ^ % Invalid input detected at '^' marker. R1(config)#priority-list 1 protocol ip low tcp http     www www R1(config)#int s 1/0    0/0.2 R1(config-subif)#pri R1(config-subif)#pri? % Unrecognized command R1(config-subif)#pri   int s0/0.2   R1(config-if)#pri R1(config-if)#priority-group                int s0/0.2 R1(config-subif)#fram ? class Define a map class on the interface de-group Associate a DE group with a DLCI interface-dlci Define a DLCI on an interface/subinterface inverse-arp Enable/disable FR inverse ARP ip Frame Relay Internet Protocol config commands map Map a protocol address to a DLCI address payload-compression Use payload compression priority-dlci-group Define a priority group of DLCIs R1(config-subif)#fram      fram pri R1(config-subif)#fram priority-dlci-group ? <1-16> Assign priority group R1(config-subif)#fram priority-dlci-group 1 ? <16-1007> DLCI for high priority R1(config-subif)#fram priority-dlci-group 1 103   2 ? <16-1007> DLCI for medium priority R1(config-subif)#fram priority-dlci-group 1 102 102 102 102 R1(config-subif)# *Mar 1 02:46:54.167: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial0/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R1(config-subif)#^Z R1# *Mar 1 02:47:22.582: %SYS-5-CONFIG_I: Configured from console by console R1#ping 180.40., 7.162 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.162, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/56/60 ms R1# R1# R1# R1# R1#sh pir R1#sh pir ^ % Invalid input detected at '^' marker. R1#sh pri % Ambiguous command: "sh pri" R1#sh prio R1#sh prio  ? printers privilege processes protocols R1#sh pr  qu R1#sh queuein R1#sh queueing Current fair queue configuration: Interface Discard Dynamic Reserved Link Priority threshold queues queues queues queues Serial0/0 64 256 0 8 1 Ethernet0/1 64 256 256 8 1 Serial0/1 64 256 0 8 1 Current DLCI priority queue configuration: Current priority queue configuration: List Queue Args 1 high protocol ip tcp port telnet 1 low protocol ip tcp port www Current custom queue configuration: Current random-detect configuration: Current per-SID queue configuration: R1# *Mar 1 02:48:00.192: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial0/0.2 from LOADING to FULL, Loading Done R1# R1# R1# R1# R1#sh queueing int s 0/90  0.2 ^ % Invalid input detected at '^' marker. R1#sh queueing int s 0/0.2   Interface Serial0/0 queueing strategy: fair Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1158 kilobits/sec R1#sh queueing int s 0/0       t ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface Ethernet IEEE 802.3 Group-Async Async Group interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Access Virtual Access interface Virtual-FrameRelay Virtual Frame Relay interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R1#sh queueing int     ? interface custom custom queueing list configuration fair fair queueing configuration priority priority queueing list configuration random-detect random early detection configuration | Output modifiers R1#sh queueing pri R1#sh queueing priority Current DLCI priority queue configuration: Current priority queue configuration: List Queue Args 1 high protocol ip tcp port telnet 1 low protocol ip tcp port www R1#sh queueing priority ? | Output modifiers R1#sh queueing priority                ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface Ethernet IEEE 802.3 Group-Async Async Group interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Access Virtual Access interface Virtual-FrameRelay Virtual Frame Relay interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R1#sh queue ser ? <0-1> Serial interface number R1#sh queue ser 0/0? : <0-1> R1#sh queue ser 0/0.2 ? % Unrecognized command R1#sh queue ser 0/0.2 ^ % Invalid input detected at '^' marker. R1#sh queue ser 0/0.2     Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1158 kilobits/sec R1#sh run int     | b interface ser   Serial0/0.2 interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 102 102 102 102 frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output Prob6 half-duplex ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! --More--  ! ! access-list 100 permit tcp host 208.28.1.2 any eq telnet access-list 101 permit ip host 208.28.1.2 any priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 --More--   R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s0./  0 /0.2 R1(config-subif)#int s0/0.2fram priority-dlci-group 1 102 102 102 102nfram priority-dlci-group 1 102 102 102 102ofram priority-dlci-group 1 102 102 102 102 fram priority-dlci-group 1 102 102 102 102 R1(config-subif)# *Mar 1 02:50:45.567: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial0/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R1(config-subif)#exit R1(config)#map-class fram ? WORD Static map class name R1(config)#map-class fram *Mar 1 02:51:00.058: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial0/0.2 from LOADING to FULL, Loading Done R1(config)#map-class fram Prob7b R1(config-map-class)#? Static maps class configuration commands: default Set a command to its defaults exit-class Exit from static map class configuration mode frame-relay Configure Map parameters help Description of the interactive help system no Negate a command or set its defaults service-policy class-based service policy R1(config-map-class)#fram > ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 56000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R1(config-map-class)#fram pri R1(config-map-class)#fram priority-group ? <1-16> Priority group number R1(config-map-class)#fram priority-group 1 ? R1(config-map-class)#fram priority-group 1 R1(config-map-class)#exit R1(config)#int s0/9 0.2 R1(config-subif)#fra class Prob7b R1(config-subif)#do sh queueing Current fair queue configuration: Interface Discard Dynamic Reserved Link Priority threshold queues queues queues queues Serial0/0 64 256 0 8 1 Ethernet0/1 64 256 256 8 1 Serial0/1 64 256 0 8 1 Current DLCI priority queue configuration: Current priority queue configuration: List Queue Args 1 high protocol ip tcp port telnet 1 low protocol ip tcp port www Current custom queue configuration: Current random-detect configuration: Current per-SID queue configuration: R1(config-subif)#q int s 0/0 R1(config-if)#fram traf R1(config-if)#fram trafint s 0/0do sh queueing Current fair queue configuration: Interface Discard Dynamic Reserved Link Priority threshold queues queues queues queues Ethernet0/1 64 256 256 8 1 Serial0/1 64 256 0 8 1 Current DLCI priority queue configuration: Current priority queue configuration: List Queue Args 1 high protocol ip tcp port telnet 1 low protocol ip tcp port www Current custom queue configuration: Current random-detect configuration: Current per-SID queue configuration: R1(config-if)#sh    do shg  fram      traff Interface Se0/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 107 56000 875 7000 0 125 875 - Interface Se0/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 103 56000 875 7000 0 125 875 - Interface Se0/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 102 56000 875 7000 0 125 875 - R1(config-if)#no do sh traffqueueingfram traf nfram trafofram traf fram traf R1(config-if)#^Z R1# *Mar 1 02:52:30.102: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b interface Serqai   ial0/0  .1 interface Serial0/0.1 point-to-point bandwidth 128 ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay class Prob7b frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output Prob6 half-duplex ! interface Serial0/1 no ip address shutdown ! router ospf 1 --More--   log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! ! ! ! map-class frame-relay Prob7b frame-relay priority-group 1 access-list 100 permit tcp host 208.28.1.2 any eq telnet access-list 101 permit ip host 208.28.1.2 any priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom --More--  ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1# R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0;/0   /0.2 R1(config-subif)#int s 0/0.2no fram trafdo sh traff queueingfram traf int s 0/0do sh queueingfra class Prob7bnfra class Prob7bofra class Prob7b fra class Prob7b R1(config-subif)#exit R1(config)#do sh access-list Extended IP access list 100 10 permit tcp host 208.28.1.2 any eq telnet Extended IP access list 101 10 permit ip host 208.28.1.2 any R1(config)#\ class-map telnet R1(config-cmap)#match ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R1(config-cmap)#match ip ? dscp Match IP DSCP (DiffServ CodePoints) precedence Match IP precedence rtp Match RTP port nos R1(config-cmap)#match ip    pro R1(config-cmap)#match protocol ? arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 --More--   decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) ipsec IP Security Protocol (ESP/AH) ipv6 IPV6 --More--   R1(config-cmap)#match protocol ip ? R1(config-cmap)#match protocol ip                   exit R1(config)#access-list 102 per tcp any any eq 23 R1(config)#access-list 102 per tcp any any eq 23exit class-map telnet R1(config-cmap)#mat acce 102 R1(config-cmap)#exit R1(config)#poly Prb7c ^ % Invalid input detected at '^' marker. R1(config)#poly Prb7c Prb7c  R1(config-pmap)#class telnet R1(config-pmap-c)#band per 100 R1(config-pmap-c)#int s 1 0/0.2 R1(config-subif)#max R1(config-subif)#max   serv R1(config-subif)#service-policy Prd b7c ^ % Invalid input detected at '^' marker. R1(config-subif)#service-policy Prb7coPrb7cuPrb7ctPrb7c Prb7c CBWFQ : Not supported on subinterfaces R1(config-subif)#exit R1(config)#no access-list 102 R1(config)#no class telen  net ^ % Invalid input detected at '^' marker. R1(config)#no pol Prb7c R1(config)#no class-map telnet R1(config)#exit R1# *Mar 1 02:57:46.052: %SYS-5-CONFIG_I: Configured from console by console R1# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#xondfif         config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#qu R3(config)#queue-list 1 qu R3(config)#queue-list 1 queue ? <0-16> queue number R3(config)#queue-list 1 queue 1 ? byte-count Specify size in bytes of a particular queue limit Set queue entry limit of a particular queue R3(config)#queue-list 1 queue 1         ? default Set custom queue for unspecified datagrams interface Establish priorities for packets from a named interface lowest-custom Set lowest number of queue to be treated as custom protocol priority queueing by protocol queue Configure parameters for a particular queue stun Establish priorities for stun packets R3(config)#queue-list 1 prio R3(config)#queue-list 1 prio  o R3(config)#queue-list 1 protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dlsw Data Link Switching ip IP ipv6 IPV6 ipx Novell IPX llc2 llc2 pad PAD links pppoe PPP over Ethernet --More--   R3(config)#queue-list 1 protocol p ? <0-16> queue number R3(config)#queue-list 1 protocol p     ip ? <0-16> queue number R3(config)#queue-list 1 protocol ip > ? <0-16> queue number R3(config)#queue-list 1 protocol ip 1 ? fragments Prioritize fragmented IP packets gt Classify packets greater than a specified size list To specify an access list lt Classify packets less than a specified size tcp Prioritize TCP packets 'to' or 'from' the specified port udp Prioritize UDP packets 'to' or 'from' the specified port R3(config)#queue-list 1 protocol ip 1 tcp ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   R3(config)#queue-list 1 protocol ip 1 tcp ftp ? R3(config)#queue-list 1 protocol ip 1 tcp ftp R3(config)#queue-list 1 protocol ip 1 tcp ftp  - R3(config)#queue-list 1 protocol ip 1 tcp ftp-data R3(config)#queue-list 1 protocol ip 1 tcp ftp-data          telnet tcp telnet 2 tcp telnet R3(config)#queue-list 1 protocol ip 2 tcp telnet                         def R3(config)#queue-list 1def def R3(config)#queue-list 1 default 3 R3(config)#queue-list 1 default 3         qu R3(config)#queue-list 1 queue 1 ? byte-count Specify size in bytes of a particular queue limit Set queue entry limit of a particular queue R3(config)#queue-list 1 queue 1 by R3(config)#queue-list 1 queue 1 byte-count 2673 R3(config)#queue-list 1 queue 1 byte-count 26733    1274 byte-count 1274 2 byte-count 1274 R3(config)#queue-list 1 queue 2 byte-count 12744 94 byte-count 1294 3 byte-count 1294 R3(config)#int s 1/2 R3(config-if)#cu R3(config-if)#custom-queue-list 1 ? R3(config-if)#custom-queue-list 1 R3(config-if)#^Z R3#sh *Mar 1 03:08:31.574: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b interface Serioa  al  1/2 interface Serial1/2 ip address 180.40.7.1 255.255.255.224 custom-queue-list 1 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown --More--  ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless ! ! ! access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo queue-list 1 protocol ip 1 tcp ftp queue-list 1 protocol ip 1 tcp ftp-data queue-list 1 protocol ip 2 tcp telnet queue-list 1 default 3 queue-list 1 queue 1 byte-count 2673 queue-list 1 queue 2 byte-count 1274 queue-list 1 queue 3 byte-count 1294 ! route-map Prob1 permit 10 --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int e fa 0/0 R3(config-if)#stand 1 ip 180 40     / .80  40.7.3 1327 ip 180.40.7.1325 ip 180.40.7.132 R3(config-if)#stand 175 pri 150 R3(config-if)# *Mar 1 03:20:59.484: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 175 state Standby -> Active R3(config-if)#stand 175 pri 150      re R3(config-if)#stand 175 pre   track ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-FrameRelay Virtual Frame Relay interface Virtual-TokenRing Virtual TokenRing R3(config-if)#stand 175 track ser 1/2 ? <1-255> Decrement value R3(config-if)#stand 175 track ser 1/2 50 R3(config-if)#i ^Z R3#in   *Mar 1 03:21:31.717: %SYS-5-CONFIG_I: Configured from console by console R3# RACK18AS> [Resuming connection 3 to r3 ... ] R3#sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 200 0009.436c.c021 ARPA FastEthernet0/0 Internet 180.40.7.130 200 0005.5e7b.c300 ARPA FastEthernet0/0 Internet 180.40.7.129 - 0013.6030.5fc0 ARPA FastEthernet0/0 Internet 180.40.7.132 - 0000.0c07.acaf ARPA FastEthernet0/0 R3# R3# R3# R3# R3# R3# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int fa  e 0/0 R1(config-if)#int e 0/0 1 R1(config-if)#stand 175 ip 180.40.7.132 R1(config-if)#stand 175 pri 10 25 R1(config-if)#stand 175 pri 125      re R1(config-if)#^Z R1# *Mar 1 03:24:00.525: %SYS-5-CONFIG_I: Configured from co RACK18AS>7 [Resuming connection 7 to r7 ... ] *Mar 1 0 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/0 R7(config-if)#stand 175 ip 180.40.7.132 R7(config-if)#^Z R7# *Mar 1 03:23:00.310: %SYS-5-CONFIG_I: Configured from console by console R7#sh stand FastEthernet0/0 - Group 175 State is Init (interface down) Virtual IP address is 180.40.7.132 Active virtual MAC address is unknown Local virtual MAC address is 0000.0c07.acaf (default) Hello time 3 sec, hold time 10 sec Preemption disabled Active router is unknown Standby router is unknown Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/0-175" (default) R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Listen unknown unknown 180.40.7.132 R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Listen unknown unknown 180.40.7.132 R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Speak unknown unknown 180.40.7.132 R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Speak unknown unknown 180.40.7.132 R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Speak unknown unknown 180.40.7.132 R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Speak unknown unknown 180.40.7.132 R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Speak unknown unknown 180.40.7.132 R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Speak unknown unknown 180.40.7.132 R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Speak unknown unknown 180.40.7.132 R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Speak unknown unknown 180.40.7.132 R7#do sh *Mar 1 03:23:28.957: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 175 state Standby -> Active R7#do sh i       sh ip   int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.133 YES manual up up BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES manual administratively down down Serial1/0 180.40.7.68 YES manual up up Serial1/1 unassigned YES manual administratively down down Serial1/2 unassigned YES manual administratively down down Serial1/3 unassigned YES manual administratively down down Serial1/4 unassigned YES manual administratively down down Serial1/5 unassigned YES manual administratively down down --More--   R7# RACK18AS>5 [Resuming connection 5 to r5 ... ] 01 S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int s   fa 0/7 S5(config-if)#switch mode acces S5(config-if)#switch mode acces          acces vlan 10 S5(config-if)#spant S5(config-if)#spant  S5(config-if)#spanning-tree po S5(config-if)#spanning-tree portf S5(config-if)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/7 but will only have effect when the interface is in a non-trunking mode. S5(config-if)#^Z S5# 03:27:37: %SYS-5-CONFIG_I: Configured from console by console S5#sh span int fa 0/7 Vlan Port ID Designated Port ID Name Prio.Nbr Cost Sts Cost Bridge ID Prio.Nbr ---------------- -------- --------- --- --------- -------------------- -------- VLAN0010 128.7 19 FWD 19 32778 0013.80e1.fe00 128.7 S5# RACK18AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.133 YES manual up up BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES manual administratively down down Serial1/0 180.40.7.68 YES manual up up Serial1/1 unassigned YES manual administratively down down Serial1/2 unassigned YES manual administratively down down Serial1/3 unassigned YES manual administratively down down Serial1/4 unassigned YES manual administratively down down Serial1/5 unassigned YES manual administratively down down --More--   R7#sh ip int briestand bri  *Mar 1 03:24:33.134: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Listen 180.40.7.129 180.40.7.131 180.40.7.132 R7# R7# R7# R7# R7# *Mar 1 03:24:35.338: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 03:24:35.398: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R7# R7#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 Listen 180.40.7.129 180.40.7.131 180.40.7.132 R7# RACK18AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int     & ^ % Invalid input detected at '^' marker. R3(config)# R3(config)#^Z R3# RACK18AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 02: R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#iont     nt s 1/2 R2(config-if)#shut R2(config-if)#^Z R2# *Mar 1 03:25:26.013: %OSPF-5-ADJCHG: Process RACK18AS>3 [Resuming connection 3 to r3 ... ] *Ma R3# *Mar 1 03:25:34.114: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down *Mar 1 03:25:34.114: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R3# *Mar 1 03:25:34.146: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 175 state Active -> Speak R3# *Mar 1 03:25:35.116: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3# R3# R3# R3# R3# R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 P Listen 180.40.7.131 unknown 180.40.7.132 R3# R3# R3# R3# R3# R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 P Listen 180.40.7.131 180.40.7.133 180.40.7.132 R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 175 100 P Listen 180.40.7.131 180.40.7.133 180.40.7.132 R3#sh stand brie              RACK18AS>2 [Resuming connection 2 to r2 ... ] 180.40.7.129 on Seria R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#no shut R2(config-if)#^Z R2# *Mar 1 03:26:36.901: %SYS-5-CONFIG_I: Configured from console by console R2# R2# R2# R2# R2# *Mar 1 03:26:38.600: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 03:26:39.602: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2# RACK18AS>1 [Resuming connection 1 to r1 ... ] by console R1# R1#sh run int e e 0/9 ^ % Invalid input detected at '^' marker. R1#sh run int e 0/9 0 Building configuration... Current configuration : 79 bytes ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 half-duplex end R1# R1# RACK18AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run int fa 0/9 ^ % Invalid input detected at '^' marker. R3#sh run int fa 0/9 0 Building configuration... Current configuration : 234 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 175 ip 180.40.7.132 standby 175 priority 150 standby 175 preempt standby 175 track Serial1/2 50 end R3# RACK18AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int fa 0/0 Building configuration... Current configuration : 128 bytes ! interface FastEthernet0/0 ip address 180.40.7.133 255.255.255.224 duplex auto speed auto standby 175 ip 180.40.7.132 end R7# R7# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1#sh run int e 0/0 1 Building configuration... Current configuration : 188 bytes ! interface Ethernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output Prob6 half-duplex standby 175 ip 180.40.7.132 standby 175 priority 125 standby 175 preempt end R1# R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip ? Global IP configuration subcommands: access-list Named access-list accounting-list Select hosts for which IP accounting information is kept accounting-threshold Sets the maximum number of accounting entries accounting-transits Sets the maximum number of transit entries address-pool Specify default IP address pooling mechanism alias Alias an IP address to a TCP port as-path BGP autonomous system path filter bgp-community format for BGP community bootp Config BOOTP services cef Cisco Express Forwarding classless Follow classless routing forwarding rules community-list Add a community list entry default-gateway Specify default gateway (if not routing IP) default-network Flags networks as candidates for default routes dhcp Configure DHCP server and relay parameters dhcp-client Configure parameters for DHCP client operation dhcp-server Specify address of DHCP server to use director Distributed director configuration commands dns Configure DNS server for a zone domain IP DNS Resolver --More--   R1(config)#ip dh R1(config)#ip dhcp ? aaa Configure aaa attributes binding DHCP address bindings bootp BOOTP specific configuration conflict DHCP address conflict parameters database Configure DHCP database agents excluded-address Prevent DHCP from assigning certain addresses limited-broadcast-address Use all 1's broadcast address ping Specify ping parameters used by DHCP pool Configure DHCP address pools relay DHCP relay agent parameters smart-relay Enable Smart Relay feature R1(config)#ip dhcp ex R1(config)#ip dhcp excluded-address 129  80.40.7.129 ? A.B.C.D High IP address R1(config)#ip dhcp excluded-address 180.40.7.129 180.40.7.133 R1(config)#dhcp ? % Unrecognized command R1(config)#dhcp      ip dhcp oo R1(config)#ip dhcp oo  poo R1(config)#ip dhcp pool ? WORD Pool name R1(config)#ip dhcp pool Prob10 ? R1(config)#ip dhcp pool Prob10 R1(dhcp-config)#net R1(dhcp-config)#net ? netbios-name-server netbios-node-type network next-server R1(dhcp-config)#ne t etw R1(dhcp-config)#network ? A.B.C.D Network number in dotted-decimal notation R1(dhcp-config)#network 180n   .40.7.128 ? /nn or A.B.C.D Network mask or prefix length R1(dhcp-config)#network 180.40.7.128 /27 R1(dhcp-config)#de R1(dhcp-config)#default-router ? Hostname or A.B.C.D Router's name or IP address R1(dhcp-config)#default-router 180.6 40.7.132 ? Hostname or A.B.C.D Router's name or IP address R1(dhcp-config)#default-router 180.40.7.132 R1(dhcp-config)#opt R1(dhcp-config)#option ? <0-254> DHCP option code R1(dhcp-config)#option 150 ? ascii Data is an NVT ASCII string hex Data is a hexadecimal string instance Specify the option instance ip Data is one or more IP addresses R1(dhcp-config)#option 150 ip > ? Hostname or A.B.C.D Server's name or IP address R1(dhcp-config)#option 150 ip 20.290  0.20.20 R1(dhcp-config)#dns R1(dhcp-config)#dns-server ? Hostname or A.B.C.D Server's name or IP address R1(dhcp-config)#dns-server 208.28.1.82 R1(dhcp-config)#dom R1(dhcp-config)#domain-name ccie.com R1(dhcp-config)#exit R1(config)#ip dhcp ex R1(config)#ip dhcp excluded-address 180.40.7.46   .146 180b .40.7.159 R1(config)#^Z R1# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip dhcp ezx  x R3(config)#ip dhcp excluded-address 180.40.7.129 180.40.7.145 R3(config)# RACK18AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh run | i     | b dhcp ip dhcp excluded-address 180.40.7.129 180.40.7.133 ip dhcp excluded-address 180.40.7.146 180.40.7.159 ! ip dhcp pool Prob10 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 option 150 ip 20.20.20.20 dns-server 208.28.1.82 domain-name ccie.com ! mpls ldp logging neighbor-changes ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! --More-- RACK18AS>3 [Resuming connection 3 to r3 ... ] R3(config)#ip dhcp pool Prob10 R3(dhcp-config)# network 180.40.7.128 255.255.255.224 R3(dhcp-config)# default-router 180.40.7.132 R3(dhcp-config)# option 150 ip 20.20.20.20 R3(dhcp-config)# dns-server 208.28.1.82 R3(dhcp-config)# domain-name ccie.com R3(dhcp-config)#!^Z R3# *Mar 1 03:38:15.491: %SYS-5-CONFIG_I: Configured from console by console R3# RACK18AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int f0 0/0 R4(config-if)#ip add dh R4(config-if)#ip add dhcp ? client-id Specify client-id to use hostname Specify value for hostname option R4(config-if)#ip add dhcp R4(config-if)#^Z R4# *Mar 1 03:40:45.083: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from 2WAY to DOWN, Neighbor Down: Interface down or detached *Mar 1 03:40:45.083: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.133 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 03:40:45.087: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 03:40:45.983: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4# R4# R4# R4#Interface FastEthernet0/0 assigned DHCP address 180.40.7.146, mask 255.255.255.224 sh     R4# R4# R4#sh ip add ^ % Invalid input detected at '^' marker. R4# *Mar 1 03:41:05.163: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.133 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 03:41:05.171: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#sh ip add   int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.146 YES DHCP up up ATM1/0 unassigned YES unset administratively down down Virtual-Access1 unassigned YES unset up up Loopback0 100.1.1.1 YES manual up up R4# RACK18AS>1 [Resuming connection 1 to r1 ... ] * ! --More--   R1#sg   h run | b dhj cp ip dhcp excluded-address 180.40.7.129 180.40.7.133 ip dhcp excluded-address 180.40.7.146 180.40.7.159 ! ip dhcp pool Prob10 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 option 150 ip 20.20.20.20 dns-server 208.28.1.82 domain-name ccie.com ! mpls ldp logging neighbor-changes ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! --More--   R1# RACK18AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 R3#sh run } | b dhsp  cpo  ip dhcp excluded-address 180.40.7.129 180.40.7.145 ! ip dhcp pool Prob10 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 option 150 ip 20.20.20.20 dns-server 208.28.1.82 domain-name ccie.com ! ip cef ip audit notify log ip audit po max-events 100 ! mpls ldp logging neighbor-changes ! ! ! ! ! ! ! ! ! --More--   R3# RACK18AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa 0/1 R2(config-if)#ip help R2(config-if)#ip helper-address 208.28.199.99 R2(config-if)#exit R2(config)#exit R2# *Mar 1 03:41:47.025: %SYS-5-CONFIG_I: Configured from console by console R2# RACK18AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.2 R1(config-subif)#ip helper R1(config-subif)#ip helper-address 208.28.1.99 R1(config-subif)#fram inter R1(config-subif)#fram interface-dlci 102 %PVC is already defined R1(config-fr-dlci)#? Frame Relay dlci configuration commands: auto Configure Automation class Assign a mapclass to a dlci default Set a command to its defaults exit Exit from FR dlci configuration mode load-interval Specify interval for load calculation for a dlci no Negate a command or set its defaults vofr Voice over Frame-Relay R1(config-fr-dlci)#exit R1(config-subif)#exitfram interface-dlci 102 mfram interface-dlci 102 pfram interface-dlci 102 fram interface-dlci 102 fram interface-dlci 102 nfram interface-dlci 102 pfram interface-dlci 102 fram interface-dlci 102 ofram interface-dlci 102  fram interface-dlci 102  R1(config-subif)# *Mar 1 03:48:24.377: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial0/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R1(config-subif)#no fram interface-dlci 102 exit fram interface-dlci 102 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R1(config-subif)#fram interface-dlci 102 pro R1(config-subif)#fram interface-dlci 102 protocol ? A.B.C.D Protocol specific address ip IP R1(config-subif)#fram interface-dlci 102 protocol ip ? A.B.C.D Protocol specific address R1(config-subif)#fram interface-dlci 102 protocol ip 180.40.7.; 162 R1(config-fr-dlci)#^Z R1# *Mar 1 03:48:49.125: %SYS-5-CONFIG_I: Configured from console by console R1# *Mar 1 03:48:59.366: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial0/0.2 from LOADING to FULL, Loading Done R1# R1# R1# R1#sh run int s 0/0.2 Building configuration... Current configuration : 225 bytes ! interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay interface-dlci 102 protocol ip 180.40.7.162 end R1# RACK18AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run int fa 0/0 1 Building configuration... Current configuration : 125 bytes ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto end R2# R2# RACK18AS>7 [Resuming connection 7 to r7 ... ] *Mar 1 03 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 0 R7(config-if)#do sh run Building configuration... Current configuration : 1453 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R7 ! logging queue-limit 100 ! ip subnet-zero ! ! ! ip audit notify log ip audit po max-events 100 mpls ldp logging neighbor-changes ! ! ! ! --More--   R7(config-if)#no stand 175 R7(config-if)#do sh int fa 0/0 FastEthernet0/0 is up, line protocol is up Hardware is AmdFE, address is 0013.6030.5fa0 (bia 0013.6030.5fa0) Internet address is 180.40.7.133/27 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:02, output 00:00:04, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 2074 packets input, 201778 bytes Received 2050 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 2161 packets output, 210703 bytes, 0 underruns 0 output errors, 0 collisions, 6 interface resets --More--   R7(config-if)#do sh int fa 0/0n rint fa 0/0uint fa 0/0nint fa 0/0 int fa 0/0 Building configuration... Current configuration : 99 bytes ! interface FastEthernet0/0 ip address 180.40.7.133 255.255.255.224 duplex auto speed auto end R7(config-if)# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#no stand   175 R3(config-if)# *Mar 1 03:51:23.250: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 175 state Active -> Disabled R3(config-if)#do sh run int fa 0/90 sh run int fa 0/90 ^ % Invalid input detected at '^' marker. R3(config-if)#do sh run int fa 0/90  0 Building configuration... Current configuration : 126 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto end R3(config-if)#stn and 174 5 ip 180;.  .40.7.14 32 R3(config-if)#stand 175 ip 180.40.7.132do sh run int fa 0/0  Building configuration... Current configuration : 155 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 175 ip 180.40.7.132 end R3(config-if)#do sh run int fa 0/0stand 175 ip 180.40.7.132do sh run int fa 0/0 90no stand 175  R3(config-if)#gl R3(config-if)#glbp ? <0-1023> Group number R3(config-if)#glbp 1 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R3(config-if)#glbp 1 ip ? A.B.C.D Virtual IP address R3(config-if)#glbp 1 ip 180.40.7.133 2 R3(config-if)# RACK18AS>6 7 [Resuming connection 7 to r7 ... ] R7(config-if)#glbp 1 ip 180.40.7.132 R7(config-if)#gl R7(config-if)#glbp 1 pri R7(config-if)#glbp 1 priority ? <1-255> Priority value R7(config-if)#glbp 1 priority                  *Mar 1 03:53:27.257: %GLBP-6-STATECHANGE: FastEthernet0/0 Grp 1 state Standby -> Active R7(config-if)# *Mar 1 03:53:37.258: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 1 Fwd 1 state Listen -> Active R7(config-if)#glbp 1 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 1 tra     wei R7(config-if)#glbp 1 weighting ? <1-254> Weighting maximum value track Interface tracking R7(config-if)#glbp 1 weighting tra R7(config-if)#glbp 1 weighting track ? <1-500> Tracked object R7(config-if)#glbp 1 weighting track                        exit R7(config)#tra R7(config)#track R7(config)#track ? <1-500> Tracked object resolution Tracking resolution parameters timer Polling interval timers R7(config)#track 1 ? interface Select an interface to track ip IP protocol R7(config)#track 1 ip ? route IP route R7(config)#track 1 ip route ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R7(config)#track 1 ip route                  int fa \        track i ? <1-500> Tracked object resolution Tracking resolution parameters timer Polling interval timers R7(config)#track 1 ? interface Select an interface to track ip IP protocol R7(config)#track 1 ip ? route IP route R7(config)#track 1 ip route ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R7(config)#track 1 ip route 20.10.1.0  /24 ? metric Route metric reachability Route reachability state R7(config)#track 1 ip route 20.10.1.0/24 re R7(config)#track 1 ip route 20.10.1.0/24 reachability ? R7(config)#track 1 ip route 20.10.1.0/24 reachability R7(config-track)#? Tracking instance configuration commands: default Set a command to its defaults delay Tracking delay exit Exit from tracking configuration mode ip Tracking IP configuration subcommands no Negate a command or set its defaults R7(config-track)#exit R7(config)#int fa 0.0  /0 R7(config-if)#glbp 1 we R7(config-if)#glbp 1 weighting gtr   tr R7(config-if)#glbp 1 weighting track 1 ? decrement Weighting decrement R7(config-if)#glbp 1 weighting track 1 dc   dec ? % Unrecognized command R7(config-if)#glbp 1 weighting track 1 ddec       R7(config-if)# RACK18AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-if)#glbp 1 ip 180.40.7.132 glbp 1 we tr R3(config-if)#glbp 1 we track 1 ? decrement Weighting decrement R3(config-if)#glbp 1 we track 1 R3(config-if)#exit R3(config)#tr R3(config)#trac R3(config)#track 1 ? interface Select an interface to track ip IP protocol R3(config)#track 1 ip ? route IP route R3(config)#track 1 ip tr  route 208/.  .28.1.0/24 re R3(config)#track 1 ip route 208.28.1.0/24 reachability R3(config-track)#exit R3(config)#^Z R3#sh *Mar 1 03:59:10.291: %SYS-5-CONFIG_I: Configured from console by console R3#sh glbp ? BVI Bridge-Group Virtual Interface FastEthernet FastEthernet IEEE 802.3 Port-channel Ethernet Channel of interfaces active Groups in active state brief Brief output capability GLBP capability disabled Groups in disabled state init Groups in init state listen Groups in listen state standby Groups in standby or speak states | Output modifiers R3#sh glbp FastEthernet0/0 - Group 1 State is Standby 1 state change, last state change 00:05:19 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 1.983 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.133, priority 100 (expires in 7.036 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 1 state Up decrement 10 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.0101 (learnt) Owner ID is 0013.6030.5fa0 Time to live: 14397.036 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.133 (primary), weighting 100 (expires in 7.032 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:05:39 MAC address is 0007.b400.0102 (default) Owner ID is 0013.6030.5fc0 Preemption enabled, min delay 30 sec Active is local, weighting 100 R3#sh run | b track track 1 ip route 208.28.1.0 255.255.255.0 reachability mpls ldp logging neighbor-changes ! ! ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! --More--  interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 301 broadcast --More--   R3# RACK18AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#^Z R7#sh run | *Mar 1 04:01:15.457: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b track track 1 ip route 20.10.1.0 255.255.255.0 reachability mpls ldp logging neighbor-changes ! ! ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! --More--  interface FastEthernet0/0 ip address 180.40.7.133 255.255.255.224 duplex auto speed auto glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.68 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.66 703 broadcast ! --More--   R7# RACK18AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s   fa 0/0 Building configuration... Current configuration : 83 bytes ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto end R2#sh run int fa 0/0 1 Building configuration... Current configuration : 125 bytes ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto end R2# RACK18AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh run int s 0/0.2 Building configuration... Current configuration : 225 bytes ! interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay interface-dlci 102 protocol ip 180.40.7.162 end R1# R1#sh access-list Extended IP access list 100 10 permit tcp host 208.28.1.2 any eq telnet Extended IP access list 101 10 permit ip host 208.28.1.2 any R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#aces  cess      class-map FTP R1(config-cmap)#match ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R1(config-cmap)#match pri R1(config-cmap)#match pri o R1(config-cmap)#match protocol ? arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 --More--   decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) ipsec IP Security Protocol (ESP/AH) ipv6 IPV6 --More--   R1(config-cmap)#match protocol ftp ? R1(config-cmap)#match protocol ftp R1(config-cmap)#exit R1(config)#class-map Telnet R1(config-cmap)#match proto R1(config-cmap)#match protocol tel R1(config-cmap)#match protocol telnet R1(config-cmap)#exit R1(config)#pol R1(config)#policy-map extra     optional R1(config-pmap)#class FTP R1(config-pmap-c)#band per 25 R1(config-pmap-c)#band per 25class FTP    Telnet R1(config-pmap-c)#class Telnetband per 25  R1(config-pmap-c)#int e 0/1 R1(config-if)#serv out optional Policy map Prob6 is already attached R1(config-if)#no serv out Prob6 R1(config-if)#no serv out Prob6serv out optional CEF or distributed CEF switching is required for NBAR 'match protocol' command R1(config-if)#exit R1(config)#ip cef R1(config)#int e 01 /1 R1(config-if)#int e 0/1p cef  R1(config)#ip cefnt e 0/1 R1(config-if)#int e 0/1p cef nt e 0/1p cef exit serv out optional R1(config-if)#^Z R1#sh run *Mar 1 04:07:48.529: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b class class-map match-all Telnet match protocol telnet class-map match-all FTP match protocol ftp class-map match-all S5Telnet match access-group 100 class-map match-all S5OtherStuff match access-group 101 ! ! policy-map optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 ! --More--  ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint --More--   frame-relay interface-dlci 102 protocol ip 180.40.7.162 ! interface Ethernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output optional half-duplex standby 175 ip 180.40.7.132 standby 175 priority 125 standby 175 preempt ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! ! ! --More--   R1#sh pol int e 0/1 Ethernet0/1 Service-policy output: optional Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth 25 (%) Bandwidth 2500 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth 25 (%) Bandwidth 2500 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 42 packets, 3209 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R1# R1# R1# R1# R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#class-map SQL R1(config-cmap)#match pro R1(config-cmap)#match protocol sq R1(config-cmap)#match protocol sql ? % Ambiguous command: "match protocol sql " R1(config-cmap)#match protocol sql  ? sqlnet sqlserver R1(config-cmap)#match protocol sqlser R1(config-cmap)#match protocol sqlserver ? R1(config-cmap)#match protocol sqlserver                          exit R1(config)#access-list 102                 do shg    access-list Extended IP access list 100 10 permit tcp host 208.28.1.2 any eq telnet Extended IP access list 101 10 permit ip host 208.28.1.2 any R1(config)#access-list 102 per tco p any anby  = y         any host 87.23.11.123 eq s R1(config)#access-list 102 per tcp any host 87.23.11.123 eq s? smtp sunrpc syslog R1(config)#access-list 102 per tcp any host 87.23.11.123 eq sq  ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   pop2 Post Office Protocol v2 (109) pop3 Post Office Protocol v3 (110) smtp Simple Mail Transport Protocol (25) sunrpc Sun Remote Procedure Call (111) syslog Syslog (514) tacacs TAC Access Control System (49) talk Talk (517) telnet Telnet (23) time Time (37) uucp Unix-to-Unix Copy Program (540) whois Nicname (43) www World Wide Web (HTTP, 80) R1(config)#access-list 102 per tcp any host 87.23.11.123 eq % Incomplete command. R1(config)# R1(config)#access-list 102 per tcp any host 87.23.11.123 eq 1434 3 R1(config)#access-list 102 per tcp any host 87.23.11.123 eq 1433 4 R1(config)#access-list 102 per tcp any host 87.23.11.123 eq 1434Naccess-list 102 per tcp any host 87.23.11.123 eq 1434Oaccess-list 102 per tcp any host 87.23.11.123 eq 1434 access-list 102 per tcp any host 87.23.11.123 eq 1434 R1(config)#NO access-list 102 per tcp any host 87.23.11.123 eq 1434access-list 102 per tcp any host 87.23.11.123 eq 1434 3 R1(config)#access-list 102 per tcp any host 87.23.11.123 eq 1433p any host 87.23.11.123 eq 1433 p any host 87.23.11.123 eq 1433 Up any host 87.23.11.123 eq 1433Dp any host 87.23.11.123 eq 1433 R1(config)#class=map SQL ^ % Invalid input detected at '^' marker. R1(config)#class=map SQLmap SQL -map SQL R1(config-cmap)#match access R1(config-cmap)#match access-group 102 R1(config-cmap)#exit R1(config)#pol R1(config)#policy-map optional R1(config-pmap)#class SQL R1(config-pmap-c)#per  ri R1(config-pmap-c)#priority ? <8-2000000> Kilo Bits per second percent % of total bandwidth R1(config-pmap-c)#priority          sha R1(config-pmap-c)#shape ? adaptive Enable Traffic Shaping adaptation to BECN average configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc only per interval fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fr-voice-adapt Enable rate adjustment depending on voice presence max-buffers Set Maximum Buffer Limit peak configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc+Be per interval R1(config-pmap-c)#shape av R1(config-pmap-c)#shape average ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R1(config-pmap-c)#shape average 65  56000 ? <256-154400000> bits per interval, sustained. Needs to be multiple of 128. Recommend not to configure it, the algorithm will find out the best value R1(config-pmap-c)#shape average 56000 128000      8                       pri R1(config-pmap-c)#priority ? <8-2000000> Kilo Bits per second percent % of total bandwidth R1(config-pmap-c)#priority 64  560  ? <32-2000000> Burst in bytes R1(config-pmap-c)#priority 56 128 R1(config-pmap-c)#^Z R1#sh *Mar 1 04:19:02.370: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b pri R1#sh run | b pri priority 56 128 policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial0/0.1 point-to-point bandwidth 128 --More--   R1#sh run | b poli policy-map optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 class SQL priority 56 128 policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 half-duplex ! interface Serial0/0 --More--   R1#sh pol int s   e 0/1 Ethernet0/1 Service-policy output: optional Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth 25 (%) Bandwidth 2500 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth 25 (%) Bandwidth 2500 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: SQL (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 102 Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 430 packets, 33616 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R1#sh ququ  eueu ing Current fair queue configuration: Interface Discard Dynamic Reserved Link Priority threshold queues queues queues queues Ethernet0/1 64 256 256 8 1 Serial0/1 64 256 0 8 1 Current DLCI priority queue configuration: Current priority queue configuration: List Queue Args 1 high protocol ip tcp port telnet 1 low protocol ip tcp port www Current custom queue configuration: Current random-detect configuration: Current per-SID queue configuration: R1#  config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int     poli R1(config)#policy-map optional R1(config-pmap)#class default-class % class map default-class not configured R1(config-pmap)#class-      exit R1(config)#class class-default ^ % Invalid input detected at '^' marker. R1(config)#class class-default class class-defaultexit class default-classpolicy-map optional R1(config-pmap)#policy-map optionalclass class-default R1(config-pmap-c)#fa R1(config-pmap-c)#fair-queue ? <16-4096> Number Dynamic Conversation Queues R1(config-pmap-c)#fair-queue 512 ? R1(config-pmap-c)#fair-queue 512   R1(config-pmap-c)#exit R1(config-pmap)#exit R1(config)#do sh run | b poli policy-map optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 class SQL priority 56 128 class class-default fair-queue 512 policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 half-duplex --More--   R1(config)#int e 0/1 R1(config-if)#fr a R1(config-if)#fair-queue ? <1-4096> Congestive Discard Threshold R1(config-if)#fair-queue 128 Must disable CBWFQ first R1(config-if)#no serve ice   R1(config-if)#no service-policy opt  ou  ut optional R1(config-if)#no service-policy out optionalfair-queue 128  R1(config-if)#fair-queue 128no service-policy out optionalno service-policy out optional  service-policy out optional  Must remove fair-queue configuration first. R1(config-if)# service-policy out optionalfair-queue 128 nfair-queue 128ofair-queue 128 fair-queue 128 R1(config-if)#no fair-queue 128 service-policy out optional R1(config-if)#^Z R1# *Mar 1 04:26:22.888: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b            co onfig t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int     pol R1(config)#policy-map optional R1(config-pmap)#class class-fr eda    default R1(config-pmap-c)#f R1(config-pmap-c)#fair-queue ? <16-4096> Number Dynamic Conversation Queues R1(config-pmap-c)#fair-queue          R1(config-pmap-c)#fair-queue R1(config-pmap-c)#? QoS policy-map class configuration commands: bandwidth Bandwidth compression Activate Compression drop Drop all packets exit Exit from QoS class action configuration mode fair-queue Enable Flow-based Fair Queuing in this Class no Negate or set default values of a command police Police priority Strict Scheduling Priority for this Class queue-limit Queue Max Threshold for Tail Drop random-detect Enable Random Early Detection as drop policy service-policy Configure QoS Service Policy set Set QoS values shape Traffic Shaping R1(config-pmap-c)#qu R1(config-pmap-c)#queue-limit ? <1-512> Packets R1(config-pmap-c)#queue-limit 128 ? R1(config-pmap-c)#queue-limit 128 R1(config-pmap-c)#ex  exit R1(config-pmap)#exit R1(config)#poli R1(config)#policy-map test R1(config-pmap)#class class-default R1(config-pmap-c)#? QoS policy-map class configuration commands: bandwidth Bandwidth compression Activate Compression drop Drop all packets exit Exit from QoS class action configuration mode fair-queue Enable Flow-based Fair Queuing in this Class no Negate or set default values of a command police Police priority Strict Scheduling Priority for this Class queue-limit Queue Max Threshold for Tail Drop random-detect Enable Random Early Detection as drop policy service-policy Configure QoS Service Policy set Set QoS values shape Traffic Shaping R1(config-pmap-c)#qu R1(config-pmap-c)#queue-limit ? <1-512> Packets R1(config-pmap-c)#queue-limit             exit R1(config-pmap)#exit R1(config)#exitclass class-defaultpolicy-map test npolicy-map testopolicy-map test policy-map test R1(config)#^Z R1# *Mar 1 04:29:20.876: %SYS-5-CONFIG_I: Configured from console by console R1#sh ru | b pol % Ambiguous command: "sh ru " R1#sh ru | b polun | b pol policy-map optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 class SQL priority 56 128 class class-default fair-queue queue-limit 128 policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 --More--   R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#pol R1(config)#policy-map optional R1(config-pmap)#class class-fra   default R1(config-pmap-c)#fai R1(config-pmap-c)#fair-queue 512 R1(config-pmap-c)#fair-queue 512 R1(config-pmap-c)#^Z R1#config tsh run | b pol *Mar 1 04:30:28.715: %SYS-5-CONFIG_I: Configured from console by console policy-map optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 class SQL priority 56 128 class class-default fair-queue 512 queue-limit 128 policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 --More--   R1#sh run | b pol policy-map optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 class SQL priority 56 128 class class-default fair-queue 512 queue-limit 128 policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 --More--   R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#pol R1(config)#policy-map Prob R1(config)#policy-map Prob16 R1(config-pmap)#class FTP R1(config-pmap-c)#shape av R1(config-pmap-c)#shape average               pol R1(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R1(config-pmap-c)#police 236  56000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R1(config-pmap-c)#police 256000 con R1(config-pmap-c)#police 256000 conform-action tr R1(config-pmap-c)#police 256000 conform-action transmit ? exceed-action action when rate is within conform and conform + exceed burst R1(config-pmap-c)#police 256000 conform-action transmit ex R1(config-pmap-c)#police 256000 conform-action transmit exceed-action dr R1(config-pmap-c)#police 256000 conform-action transmit exceed-action drop ? violate-action action when rate is greater than conform + exceed burst R1(config-pmap-c)#police 256000 conform-action transmit exceed-action drop R1(config-pmap-c-police)#exit R1(config-pmap-c)#exit R1(config-pmap)#class Telnet R1(config-pmap-c)#pol R1(config-pmap-c)#police 56000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R1(config-pmap-c)#police 56000 1400 ? <1000-512000000> Burst bytes be Excess burst conform-action action when rate is less than conform burst pir Peak Information Rate R1(config-pmap-c)#police 56000 1400 3500 ? conform-action action when rate is less than conform burst R1(config-pmap-c)#police 56000 1400 3500 con R1(config-pmap-c)#police 56000 1400 3500 conform-action ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R1(config-pmap-c)#police 56000 1400 3500 conform-action set R1(config-pmap-c)#police 56000 1400 3500 conform-action set-t R1(config-pmap-c)#police 56000 1400 3500 conform-action set-t p R1(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 ? exceed-action action when rate is within conform and conform + exceed burst R1(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 e$0 1400 3500 conform-action set-prec-transmit 1 ex  R1(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action ? drop drop packet set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R1(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action se R1(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action set-p R1(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 ? violate-action action when rate is greater than conform + exceed burst R1(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 vi R1(config-pmap-c)#$smit 1 exceed-action set-prec-transmit 0 violate-action dr R1(config-pmap-c)#$eed-action set-prec-transmit 0 violate-action drop R1(config-pmap-c-police)#int     clas  s class-default R1(config-pmap-c)#fai R1(config-pmap-c)#fair-queue 100 Number of dynamic queues must be a power of 2 (16, 32, 64, 128, 256, 512, 1024) R1(config-pmap-c)#fair-queue 100   ? <16-4096> Number Dynamic Conversation Queues R1(config-pmap-c)#fair-queue            qu R1(config-pmap-c)#queue-limit 100 fair-queue or bandwidth on the class is required to issue this command R1(config-pmap-c)#fa R1(config-pmap-c)#fair-queue R1(config-pmap-c)#fair-queue queue-limit 100 R1(config-pmap-c)#int d 0-/0.1 ^ % Invalid input detected at '^' marker. R1(config)#int d 0-/0.1/0.1  0/0.1 s 0/0.1 R1(config-subif)#servi R1(config-subif)#service-policy Prob16 oProb16 uProb16 tProb16  Prob16  CBWFQ : Not supported on subinterfaces R1(config-subif)#exit R1(config)#map= -class fram Pro *Mar 1 04:36:17.010: %ALIGN-3-SPURIOUS: Spurious memory access made at 0x804B0AD8 reading 0x8 R1(config)#map-class fram Pro16 R1(config-map-class)#ser R1(config-map-class)#service-policy ? input input policy output output policy R1(config-map-class)#service-policy out Porb   rob16 ? R1(config-map-class)#service-policy out Prob16 R1(config-map-class)#int s 1  0/0.1 R1(config-subif)#do sh run           class Prob16 ^ % Invalid input detected at '^' marker. R1(config-subif)#class Prob16fclass Prob16rclass Prob16aclass Prob16mclass Prob16 class Prob16 R1(config-subif)#^Z R1# *Mar 1 04:37:06.739: %SYS-5-CONFIG_I: Configured from console by console R1#sjh    h run | b pol policy-map optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 class SQL priority 56 128 class class-default fair-queue 512 queue-limit 128 policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 policy-map Prob16 class FTP police cir 256000 conform-action transmit exceed-action drop class Telnet --More--   police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop class class-default fair-queue queue-limit 100 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 180.40.7.65 255.255.255.224 --More--   ip ospf network point-to-multipoint frame-relay class Prob16 frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay interface-dlci 102 protocol ip 180.40.7.162 ! interface Ethernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output optional half-duplex standby 175 ip 180.40.7.132 standby 175 priority 125 standby 175 preempt ! interface Serial0/1 no ip address shutdown ! --More--  router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! ! ! ! map-class frame-relay Prob7b frame-relay priority-group 1 ! map-class frame-relay Pro16 service-policy output Prob16 ! map-class frame-relay Prob16 access-list 100 permit tcp host 208.28.1.2 any eq telnet access-list 101 permit ip host 208.28.1.2 any access-list 102 permit tcp any host 87.23.11.123 eq 1433 access-list 102 permit udp any host 87.23.11.123 eq 1433 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www --More--  ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1# R1#sh poli R1#sh policy-map Policy Map optional Class FTP Bandwidth 25 (%) Max Threshold 64 (packets) Class Telnet Bandwidth 25 (%) Max Threshold 64 (packets) Class SQL Strict Priority Bandwidth 56 (kbps) Burst 128 (Bytes) Class class-default Flow based Fair Queueing Bandwidth 0 (kbps) Max Threshold 128 (packets) Policy Map Prob6 Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class S5OtherStuff police cir 5000000 bc 156250 conform-action transmit exceed-action set-prec-transmit 3 Policy Map Prob16 Class FTP police cir 256000 bc 8000 --More--   conform-action transmit exceed-action drop Class Telnet police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop Class class-default Flow based Fair Queueing Bandwidth 0 (kbps) Max Threshold 100 (packets) R1#sh runq       config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#no map-class frame-relay Pro16 R1(config)#no map-class frame-relay Pro16b16no map-class frame-relay Prob16 map-class frame-relay Prob16 map-class frame-relay Prob16  R1(config-map-class)# service-policy output Prob16 R1(config-map-class)#^Z R1#sh run Building configuration... *Mar 1 04:40:13.686: %SYS-5-CONFIG_I: Configured from console by console Current configuration : 3133 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! logging queue-limit 100 ! memory-size iomem 10 ip subnet-zero ! ! no ip domain lookup ip dhcp excluded-address 180.40.7.129 180.40.7.133 ip dhcp excluded-address 180.40.7.146 180.40.7.159 ! ip dhcp pool Prob10 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 --More--   option 150 ip 20.20.20.20 dns-server 208.28.1.82 domain-name ccie.com ! ip cef mpls ldp logging neighbor-changes ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! class-map match-all Telnet --More--   match protocol telnet class-map match-all FTP match protocol ftp class-map match-all S5Telnet match access-group 100 class-map match-all SQL match access-group 102 class-map match-all S5OtherStuff match access-group 101 ! ! policy-map optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 class SQL priority 56 128 class class-default fair-queue 512 queue-limit 128 policy-map Prob6 class S5Telnet --More--   bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 policy-map Prob16 class FTP police cir 256000 conform-action transmit exceed-action drop class Telnet police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop class class-default fair-queue queue-limit 100 ! ! ! ! interface Ethernet0/0 --More--   ip address 208.28.1.1 255.255.255.0 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay no fair-queue ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay class Prob16 frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay interface-dlci 102 protocol ip 180.40.7.162 ! interface Ethernet0/1 --More--   ip address 180.40.7.131 255.255.255.224 service-policy output optional half-duplex standby 175 ip 180.40.7.132 standby 175 priority 125 standby 175 preempt ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! ! ! ! map-class frame-relay Prob7b frame-relay priority-group 1 --More--  ! map-class frame-relay Prob16 service-policy output Prob16 access-list 100 permit tcp host 208.28.1.2 any eq telnet access-list 101 permit ip host 208.28.1.2 any access-list 102 permit tcp any host 87.23.11.123 eq 1433 access-list 102 permit udp any host 87.23.11.123 eq 1433 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 exec-timeout 0 0 --More--   logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1# R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#pol R1(config)#policy-map Prob17 R1(config-pmap)#class ftp % class map ftp not configured R1(config-pmap)#class ftp   FTP R1(config-pmap-c)#sha R1(config-pmap-c)#shape av R1(config-pmap-c)#shape average         pe R1(config-pmap-c)#shape peak ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R1(config-pmap-c)#shape peak R1# *Mar 1 04:43:44.652: %SYS-5-CONFIG_I: Configured from console by console R1#co  config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#class FTPftppolicy-map Prob17 R1(config-pmap)#policy-map Prob17class FTP ftpFTP R1(config-pmap-c)#shape peak ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R1(config-pmap-c)#shape peak 256000 ? <256-154400000> bits per interval, sustained. Needs to be multiple of 128. Recommend not to configure it, the algorithm will find out the best value R1(config-pmap-c)#shape peak 256000 R1(config-pmap-c)#do sh pol Policy Map optional Class FTP Bandwidth 25 (%) Max Threshold 64 (packets) Class Telnet Bandwidth 25 (%) Max Threshold 64 (packets) Class SQL Strict Priority Bandwidth 56 (kbps) Burst 128 (Bytes) Class class-default Flow based Fair Queueing Bandwidth 0 (kbps) Max Threshold 128 (packets) Policy Map Prob6 Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class S5OtherStuff police cir 5000000 bc 156250 conform-action transmit exceed-action set-prec-transmit 3 Policy Map Prob16 Class FTP police cir 256000 bc 8000 --More--   conform-action transmit exceed-action drop Class Telnet police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop Class class-default Flow based Fair Queueing Bandwidth 0 (kbps) Max Threshold 100 (packets) Policy Map Prob17 Class FTP Traffic Shaping Peak Rate Traffic Shaping CIR 256000 (bps) Max. Buffers Limit 1000 (Packets) R1(config-pmap-c)#sh av R1(config-pmap-c)#sh average ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R1(config-pmap-c)#sh average 256000 ? <256-154400000> bits per interval, sustained. Needs to be multiple of 128. Recommend not to configure it, the algorithm will find out the best value R1(config-pmap-c)#sh average 256000 R1(config-pmap-c)#sh average 256000 do sh pol  Policy Map optional Class FTP Bandwidth 25 (%) Max Threshold 64 (packets) Class Telnet Bandwidth 25 (%) Max Threshold 64 (packets) Class SQL Strict Priority Bandwidth 56 (kbps) Burst 128 (Bytes) Class class-default Flow based Fair Queueing Bandwidth 0 (kbps) Max Threshold 128 (packets) Policy Map Prob6 Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class S5OtherStuff police cir 5000000 bc 156250 conform-action transmit exceed-action set-prec-transmit 3 Policy Map Prob16 Class FTP police cir 256000 bc 8000 --More--   conform-action transmit exceed-action drop Class Telnet police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop Class class-default Flow based Fair Queueing Bandwidth 0 (kbps) Max Threshold 100 (packets) Policy Map Prob17 Class FTP Traffic Shaping Average Rate Traffic Shaping CIR 256000 (bps) Max. Buffers Limit 1000 (Packets) R1(config-pmap-c)#class Telnet R1(config-pmap-c)#sh av 56000 R1(config-pmap-c)#class class-f default R1(config-pmap-c)#bas nd 512 R1(config-pmap-c)#shap pee ak 60000  000 R1(config-pmap-c)#int s       exit R1(config-pmap)#exit R1(config)#int s 0/0 R1(config-if)#swer   erv R1(config-if)#service-policy Prob17oProb17uProb17tProb17 Prob17 R1(config-if)#^Z R1#sh ruh *Mar 1 04:54:59.065: %SYS-5-CONFIG_I: Configured from console by console R1#sh ruh   n | b pol policy-map optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 class SQL priority 56 128 class class-default fair-queue 512 queue-limit 128 policy-map Prob6 class S5Telnet bandwidth 1000 class S5OtherStuff police cir 5000000 conform-action transmit exceed-action set-prec-transmit 3 policy-map Prob16 class FTP police cir 256000 conform-action transmit exceed-action drop class Telnet --More--   police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop class class-default fair-queue queue-limit 100 policy-map Prob17 class FTP shape average 256000 class Telnet shape average 56000 class class-default bandwidth 512 shape peak 600000 ! ! ! ! interface Ethernet0/0 ip address 208.28.1.1 255.255.255.0 half-duplex ! --More--  interface Serial0/0 no ip address service-policy output Prob17 encapsulation frame-relay ! interface Serial0/0.1 point-to-point bandwidth 128 ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay class Prob16 frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point bandwidth 128 ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay interface-dlci 102 protocol ip 180.40.7.162 ! interface Ethernet0/1 ip address 180.40.7.131 255.255.255.224 service-policy output optional half-duplex --More--   R1# RACK18AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#do sh ruhn  n | traffi sh run | traffi ^ % Invalid input detected at '^' marker. R2(config)#do sh run | traffi traffii traffi traffic-shape rate 64000 8000 8000 1000 traffic-shape adaptive 32000 traffic-shape rate 64000 8000 8000 1000 traffic-shape adaptive 32000 R2(config)#int s 0/  1/0.2 R2(config-subif)#traf R2(config-subif)#traffic-shape rate 64000  ? % Unrecognized command R2(config-subif)#traffic-shape rate 6400      ? <8000-100000000> Target Bit Rate (bits per second) R2(config-subif)#traffic-shape rate 64000 ? <0-100000000> bits per interval, sustained R2(config-subif)#traffic-shape rate 64000                          exit R2(config)#exitint s 1/0.2 R2(config-subif)#no traffic-shape rate 64000 8000 8000 1000 R2(config-subif)#no traffic-shape adaptive 32000 R2(config-subif)#exit R2(config)#fra   map  -l class fram proi b    Prob18 R2(config-map-class)#fram ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 56000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R2(config-map-class)#fram cir 64000 R2(config-map-class)#fram bc 640 R2(config-map-class)#int s 1/0.2 R2(config-subif)#fram class map Prob18 ^ % Invalid input detected at '^' marker. R2(config-subif)#fram class map Prob18          Prob18 ? R2(config-subif)#fram class Prob18 R2(config-subif)#int     int s 0\ 1  1/0.1 R2(config-subif)#int s 1/0.1fram class Prob18 map Prob18int s 1/0.2 fram bc 640cir 64000map-class fram Prob18 exit no traffic-shape adaptive 32000rate 64000 8000 8000 1000 R2(config-subif)#no traffic-shape rate 64000 8000 8000 1000int s 1/0.1 no traffic-shape rate 64000 8000 8000 1000 no traffic-shape rate 64000 8000 8000 1000int s 1/0.1 fram class Prob18 map Prob18int s 1/0.2 fram bc 640cir 64000map-class fram Prob18 exit no traffic-shape adaptive 32000rate 64000 8000 8000 1000adaptive 32000  R2(config-subif)#int s 1/0 R2(config-if)#fram tra % Ambiguous command: "fram tra" R2(config-if)#fram traff R2(config-if)#exit R2(config)#do sh access % Ambiguous command: "sh access" R2(config)#do sh access-lst sh access-lst ^ % Invalid input detected at '^' marker. R2(config)#do sh access-lst   R2(config)#access-list 100 per     deny ospf any any R2(config)#access-list 100 e per ip any any R2(config)#fra R2(config)#frame-relay de R2(config)#frame-relay de-list ? <1-10> DE list numbers R2(config)#frame-relay de-list ` 1 ? interface Identify packets from a named interface protocol Identify packets by protocol R2(config)#frame-relay de-list 1 pro R2(config)#frame-relay de-list 1 protocol ? appletalk AppleTalk arp IP ARP bridge Bridging clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System compressedtcp Compressed TCP decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 ip IP ipx Novell IPX R2(config)#frame-relay de-list 1 protocol ip ? fragments Classify fragmented IP packets gt Identify packets greater than a specified size list To specify an access list lt Identify packets less than a specified size tcp Classify TCP packets 'to' or 'from' the specified port udp Classify UDP packets 'to' or 'from' the specified port R2(config)#frame-relay de-list 1 protocol ip li R2(config)#frame-relay de-list 1 protocol ip list 100 ? R2(config)#frame-relay de-list 1 protocol ip list 100 R2(config)#fram       R2# *Mar 1 04:58:59.259: %SYS-5-CONFIG_I: Configured from console by console R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 0/0   1/0.1 2 R2(config-subif)#fram de R2(config-subif)#fram de-group 1 201 ? R2(config-subif)#fram de-group 1 201 R2(config-subif)#^Z R2# *Mar 1 05:00:21.998: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b fram frame-relay de-list 1 protocol ip list 100 ! ! ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! interface FastEthernet0/0 --More--   R2#rame-relay de-list 1 protocol ip list 100 R2#sh run | b fram frame-relay de-list 1 protocol ip list 100 ! ! ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! ! interface FastEthernet0/0 --More--   no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 --More--   ip ospf network point-to-multipoint frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay class Prob18 frame-relay de-group 1 201 frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clockrate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 --More--   no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server no ip http secure-server ip classless ! --More--  ! ! ! map-class frame-relay Prob18 frame-relay cir 64000 frame-relay bc 640 access-list 100 deny ospf any any access-list 100 permit ip any any ! ! call rsvp-sync ! ! mgcp profile default ! ! ! dial-peer cor custom ! ! ! ! ! --More--  line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R2# R2# RACK18AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int     int s 1/90  0 R3(config-if)#fram      fram map ip 180 .40. .40. .40.7.65 com   ? <16-1007> DLCI vc-bundle vc-bundle R3(config-if)#fram map ip 180.40.7.65 301 ? broadcast Broadcasts should be forwarded to this address cisco Use CISCO Encapsulation compress Enable TCP/IP and RTP/IP header compression ietf Use RFC1490/RFC2427 Encapsulation nocompress Do not compress TCP/IP headers payload-compression Use payload compression rtp RTP header compression parameters tcp TCP header compression parameters R3(config-if)#fram map ip 180.40.7.65 301 com R3(config-if)#fram map ip 180.40.7.65 301 compress ? active Always compress TCP/IP and RTP/IP headers connections Maximum number of compressed TCP & RTP connections passive Compress for destinations sending compressed headers R3(config-if)#fram map ip 180.40.7.65 301 compress ac R3(config-if)#fram map ip 180.40.7.65 301 compress active ? connections Maximum number of compressed TCP & RTP connections R3(config-if)#fram map ip 180.40.7.65 301 compress active con R3(config-if)#fram map ip 180.40.7.65 301 compress active connections ? <3-256> Number of TCP/RTP connections R3(config-if)#fram map ip 180.40.7.65 301 compress active connections 20 R3(config-if)#do sh run int s 1/0 Building configuration... Current configuration : 290 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 301 compress active connections 20 frame-relay map ip 180.40.7.67 302 broadcast frame-relay map ip 180.40.7.68 307 broadcast end R3(config-if)# R3(config-if)#do sh run int s 1/0fram map ip 180.40.7.65 301 compress active connections 20 bro R3(config-if)#fram map ip 180.40.7.65 301 compress active connections 20 bro ^ % Invalid input detected at '^' marker. R3(config-if)#fram map ip 180.40.7.65 301 compress active connections 20 bro    bcompress active connections 20 rcompress active connections 20  compress active connections 20  R3(config-if)#fram map ip 180.40.7.65 301 br compress active connections 20 compress active connections 20 brodo sh run int s 1/0  Building configuration... Current configuration : 300 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 301 broadcast compress active connections 20 frame-relay map ip 180.40.7.67 302 broadcast frame-relay map ip 180.40.7.68 307 broadcast end R3(config-if)#fram ip ? rtp RTP header compression parameters tcp TCP header compression parameters R3(config-if)#fram ip rtp ? compression-connections Maximum number of compressed RTP connections header-compression Enable RTP/IP header compression R3(config-if)#fram ip rtp             ^Z R3# *Mar 1 05:06:47.414: %SYS-5-CONFIG_I: Configured from console by console R3# R3#