=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2005.12.20 14:27:39 =~=~=~=~=~=~=~=~=~=~=~= R7# R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#stan R7(config-if)#standby ? <0-255> group number authentication Authentication delay HSRP initialisation delay ip Enable HSRP and set the virtual IP address mac-address Virtual MAC address name Redundancy name string preempt Overthrow lower priority Active routers priority Priority level redirects Configure sending of ICMP Redirect messages with an HSRP virtual IP address as the gateway IP address timers Hello and hold timers track Priority tracking use-bia HSRP uses interface's burned in address R7(config-if)#standby 1 ip add R7(config-if)#standby 1 ip addr R7(config-if)#standby 1 ip addr    ? A.B.C.D Virtual IP address R7(config-if)#standby 1 ip 180.40.7.132 ? secondary Make this IP address a secondary virtual IP address R7(config-if)#standby 1 ip 180.40.7.132 R7(config-if)# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#standby 1 ip 180.40.7.132 R3(config-if)#stand R3(config-if)#standby p[ ri R3(config-if)#standby priority 1501priority 150 priority 150 R3(config-if)# RACK1AS>7 [Resuming connection 7 to r7 ... ] *Mar R7(config-if)#do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 208.28.1.1 YES manual up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.131 YES manual up up Serial1/0 unassigned YES manual up up Serial1/0.1 180.40.7.65 YES manual up up Serial1/0.2 180.40.7.161 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 unassigned YES unset administratively down down Serial1/3 unassigned YES unset administratively down down --More--   R7(config-if)#do sh stand FastEthernet0/1 - Group 1 State is Active 2 state changes, last state change 00:00:46 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac01 Local virtual MAC address is 0000.0c07.ac01 (default) Hello time 3 sec, hold time 10 sec Next hello sent in 1.622 secs Preemption disabled Active router is local Standby router is 180.40.7.129, priority 150 (expires in 7.612 sec) Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/1-1" (default) R7(config-if)#q do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/1 1 100 Active local 180.40.7.129 180.40.7.132 R7(config-if)# RACK1AS>3 [Resuming connection 3 to r3 ... ] standby 1 priority 150 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 1 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#stan R3(config-if)#standby 1 pre R3(config-if)#standby 1 preempt R3(config-if)# *Mar 1 08:25:37.506: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 1 state Standby -> Active R3(config-if)#stand R3(config-if)#standby 1 tr R3(config-if)#standby 1 track ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing R3(config-if)#standby 1 track ser R3(config-if)#standby 1 track serial i 1/2 R3(config-if)#standby 1 track serial 1/2 ? <1-255> Decrement value R3(config-if)#standby 1 track serial 1/2                            do sh run int s 1/2 Building configuration... Current configuration : 123 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 end R3(config-if)#do sh run int s 1/2       fa 0/0 Building configuration... Current configuration : 223 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 1 ip 180.40.7.132 standby 1 priority 150 standby 1 preempt standby 1 track Serial1/2 end R3(config-if)#do sh stat n FastEthernet0/0 - Group 1 State is Active 2 state changes, last state change 00:01:26 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac01 Local virtual MAC address is 0000.0c07.ac01 (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.212 secs Preemption enabled Active router is local Standby router is 180.40.7.131, priority 100 (expires in 8.210 sec) Priority 150 (configured 150) Track interface Serial1/2 state Up decrement 10 IP redundancy name is "hsrp-Fa0/0-1" (default) R3(config-if)#do sh stanrun int fa 0/0s 1/2  51 sh run int s 1/2 51 ^ % Invalid input detected at '^' marker. R3(config-if)#do sh run int s 1/2 51stan run int fa 0/0s 1/2 standby 1 track serial 1/2preempt track serial 1/2 n 51 R3(config-if)#dp   o sh run int s   fa 0/0 Building configuration... Current configuration : 226 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 1 ip 180.40.7.132 standby 1 priority 150 standby 1 preempt standby 1 track Serial1/2 51 end R3(config-if)#int s 1/2 R3(config-if)#hsu ~   sht ut R3(config-if)# *Mar 1 08:27:53.754: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)# *Mar 1 08:27:55.749: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 1 08:27:56.750: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 1 99 P Active local 180.40.7.131 180.40.7.132 R3(config-if)# RACK1AS>7 [Resuming connection 7 to r7 ... ] *Mar R7(config-if)#stand 1 pre R7(config-if)# *Mar 1 08:28:04.199: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 1 state Standby -> Active R7(config-if)# R7(config-if)# R7(config-if)# R7(config-if)# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Ma R3(config-if)#no h shut R3(config-if)#^Z R3# *Mar 1 08:29:03.111: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 08:29:04.742: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 08:29:05.744: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3# *Mar 1 08:29:07.579: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 1 state Standby -> Active R3# R3# R3# R3# *Mar 1 08:29:14.879: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from LOADING to FULL, Loading Done R3#sh run int s   da    d fa 0/0 Building configuration... Current configuration : 226 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 1 ip 180.40.7.132 standby 1 priority 150 standby 1 preempt standby 1 track Serial1/2 51 end R3# RACK1AS>7 [Resuming connection 7 to r7 ... ] * R7(config-if)#^Z R7#sh run *Mar 1 08:28:43.908: %SYS-5-CONFIG_I: Configured from console by console R7#sh run int fa 0/1 Building configuration... Current configuration : 174 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex standby 1 ip 180.40.7.132 standby 1 preempt service-policy output Prob6 end R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#no standby 1 ip 180.40.7.132 R7(config-if)#no standby 1 preempt R7(config-if)# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#co  int fa 0/0 R3(config-if)#do sh run int f 0/1 Building configuration... Current configuration : 83 bytes ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto end R3(config-if)#do sh run int f 0/1 0 Building configuration... Current configuration : 226 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 1 ip 180.40.7.132 standby 1 priority 150 standby 1 preempt standby 1 track Serial1/2 51 end R3(config-if)#no standby 1 ip 180.40.7.132 R3(config-if)#no *Mar 1 08:30:33.187: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 1 state Active -> Disabled R3(config-if)#no standby 1 priority 150 R3(config-if)#no standby 1 preempt R3(config-if)#no standby 1 track Serial1/2 51 R3(config-if)#vr R3(config-if)#vrrp ? <1-255> Group number R3(config-if)#vrrp 1 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R3(config-if)#vrrp 1 ip ? A.B.C.D VRRP group IP address R3(config-if)#vrrp 1 ip 180.40.7.132 ? secondary Specify an additional VRRP address for this group R3(config-if)#vrrp 1 ip 180.40.7.132 R3(config-if)# *Mar 1 08:31:16.606: %VRRP-6-STATECHANGE: Fa0/0 Grp 1 state Init -> Backup R3(config-if)#vrrp *Mar 1 08:31:20.216: %VRRP-6-STATECHANGE: Fa0/0 Grp 1 state Backup -> Master R3(config-if)#vrrp 1 pro R3(config-if)#vrrp 1 pro  R3(config-if)#vrrp 1 pri R3(config-if)#vrrp 1 priority ? <1-254> Priority level R3(config-if)#vrrp 1 priority 150 ? R3(config-if)#vrrp 1 priority 150 ip 180.40.7.132 priority 150  R3(config-if)#vrrp 1 pre R3(config-if)# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#vrrp 1 ip 180.40.7.132 R7(config-if)# *Mar 1 08:31:17.099: %VRRP-6-STATECHANGE: Fa0/1 Grp 1 state Init -> Backup R7(config-if)#veep 1 pre ^ % Invalid input detected at '^' marker. R7(config-if)#veep 1 prep 1 pre p 1 pre rp 1 prerp 1 pre R7(config-if)# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#tra R3(config-if)#tra? traffic-shape transmit-interface R3(config-if)#tra   exit    vrrp 1? <1-255> R3(config-if)#vrrp 1 :>  ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R3(config-if)#vrrp 1        exit R3(config)#tra R3(config)#track R3(config)#track   ? <1-500> Tracked object resolution Tracking resolution parameters timer Polling interval timers R3(config)#track 1 ? interface Select an interface to track ip IP protocol R3(config)#track 1 int ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing R3(config)#track 1 int ser 1/2 ? ip IP parameters line-protocol Track interface line-protocol R3(config)#track 1 int ser 1/2 ip ? routing Track interface IP routing capability R3(config)#track 1 int ser 1/2 ip      2 lin R3(config)#track 1 int ser 1/2 line-protocol ? R3(config)#track 1 int ser 1/2 line-protocol R3(config-track)#? Tracking instance configuration commands: default Set a command to its defaults delay Tracking delay exit Exit from tracking configuration mode no Negate a command or set its defaults R3(config-track)#exit R3(config)#int fa 0/0 R3(config-if)#tr? traffic-shape transmit-interface trunk-group R3(config-if)#tr  vrrp 1 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R3(config-if)#vrrp 1 track ? % Unrecognized command R3(config-if)#vrrp 1 track              enb d R3# *Mar 1 08:34:54.700: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int fa 0/0 Building configuration... Current configuration : 171 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 1 ip 180.40.7.132 vrrp 1 priority 150 end R3# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#do sh run int fa 0/1 Building configuration... Current configuration : 152 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 1 ip 180.40.7.132 service-policy output Prob6 end R7(config-if)# R7# *Mar 1 08:34:35.777: %SYS-5-CONFIG_I: Configured from console by console R7# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip dhcp ex R3(config)#ip dhcp excluded-address ? A.B.C.D Low IP address R3(config)#ip dhcp excluded-address 180.40.7.129 ? A.B.C.D High IP address R3(config)#ip dhcp excluded-address 180.40.7.129 R3(config)#ip dhcp excluded-address 180.40.7.129    31 180.40.7.132 R3(config)#ip dhcp pol ol ? WORD Pool name R3(config)#ip dhcp pool Prob11 ? R3(config)#ip dhcp pool Prob11 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#net R3(dhcp-config)#netwotk   R3(dhcp-config)#network ? A.B.C.D Network number in dotted-decimal notation R3(dhcp-config)#network 180.40.7.128 ? /nn or A.B.C.D Network mask or prefix length R3(dhcp-config)#network 180.40.7.128 /27 ? R3(dhcp-config)#network 180.40.7.128 /27 R3(dhcp-config)#def R3(dhcp-config)#default-router 180.40.7.132 R3(dhcp-config)#d dns R3(dhcp-config)#dns-server 1 208.28.1.82 R3(dhcp-config)#dom R3(dhcp-config)#domain-name ? WORD Domain name R3(dhcp-config)#domain-name cisco.com.com .com .com .com .com b.coma.coms.coms.comc.como.comn.coms.comu.coml.comt.comi.comn.comg.com R3(dhcp-config)#tfp? % Unrecognized command R3(dhcp-config)#tfp   tfop  ? % Unrecognized command R3(dhcp-config)#tf  ? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   utilization Configure various utilization parameters vrf Associate this pool with a VRF R3(dhcp-config)#option ? <0-254> DHCP option code R3(dhcp-config)#option 150 ? ascii Data is an NVT ASCII string hex Data is a hexadecimal string instance Specify the option instance ip Data is one or more IP addresses R3(dhcp-config)#option 150 ip ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#option 150 ip 20.20.20.20 ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#option 150 ip 20.20.20.20 R3(dhcp-config)#exit R3(config)# RACK1AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#ip add dhcp R4(config-if)# *Mar 1 08:44:41.357: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 08:44:41.357: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)# *Mar 1 08:44:46.385: IP: s=0.0.0.0 (local), d=255.255.255.255, len 604, policy rejected -- normal forwarding *Mar 1 08:44:46.389: IP: s=0.0.0.0 (local), d=180.40.7.129, len 56, policy rejected -- normal forwarding R4(config-if)# *Mar 1 08:44:47.893: IP: s=0.0.0.0 (local), d=180.40.7.129, len 56, policy rejected -- normal forwarding *Mar 1 08:44:48.397: IP: s=0.0.0.0 (local), d=255.255.255.255, len 604, policy rejected -- normal forwarding R4(config-if)# *Mar 1 08:44:52.529: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.224, hostname R4 R4(config-if)# *Mar 1 08:44:52.953: IP: s=180.40.7.130 (local), d=180.40.7.129 (FastEthernet0/0), len 64, policy rejected -- normal forwarding R4(config-if)#do u all All possible debugging has been turned off R4(config-if)# *Mar 1 08:44:56.177: IP: s=180.40.7.130 (local), d=180.40.7.131 (FastEthernet0/0), len 64, policy rejected -- normal forwarding R4(config-if)# *Mar 1 08:44:57.973: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)# *Mar 1 08:45:01.189: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config)#do sh ip dhcp bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 0063.6973.636f.2d30. Mar 02 1993 08:42 AM Automatic 3033.302e.3835.6633. 2e37.3032.302d.4661. 302f.30 R3(config)# R3(config)# R3(config)# R3(config)# R3(config)# R3# *Mar 1 08:43:52.862: %SYS-5-CONFIG_I: Configured from console by console R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip dhcp pool R3(config)#ip dhcp pool R4 R3(dhcp-config)#host ? A.B.C.D IP address in dotted-decimal notation R3(dhcp-config)#host 180.40.7.130 ? /nn or A.B.C.D Network mask or prefix length R3(dhcp-config)#host 180.40.7.130 /27 % A binding already exists for 180.40.7.130. R3(dhcp-config)# RACK1AS>4 [Resuming connection 4 to r4 ... ] R4(config-if)#shut RACK1AS>3 [Resuming connection 3 to r3 ... ] R3(dhcp-config)#do cle ip dhcp d bin % Ambiguous command: "do cle ip dhcp bin" R3(config)#end R3# *Mar 1 08:45:54.633: %SYS-5-CONFIG_I: Configured from console by console R3#clea ip dhcp ? binding DHCP address bindings conflict DHCP address conflicts pool Clear objects from a specific pool server Miscellaneous DHCP server information subnet Leased subnets R3#clea ip dhcp bin ? * Clear all automatic bindings A.B.C.D Clear a specific binding R3#clea ip dhcp bin * R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#enddo cle ip dhcp binhost 180.40.7.130 /27ip dhcp pool R4  R3(dhcp-config)#ip dhcp pool R4end do cle ip dhcp binhost 180.40.7.130 /27 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation c *Mar 1 08:46:12.787: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expiredommands update Dynamic updates --More--   R3(dhcp-config)#li R3(dhcp-config)#li  cli R3(dhcp-config)#client-i R3(dhcp-config)#client-identifier ? WORD Dotted-hexadecimal string (aabb.ccdd.eeff ...) R3(dhcp-config)#client-identifier 0063.6973.636f.2d30.3033.302e.3835.6633.2e3$tifier 0063.6973.636f.2d30.3033.302e.3835.6633.2e37 .3032.3023.6973.636f.2d30.3033.302e.3835.6633.2e37.3032.302d .4661.302f.2d30.3033.302e.3835.6633.2e37.3032.302d.4661.302f .30 R3(dhcp-config)# RACK1AS>6 [Resuming connection 6 to r6 ... ] 03:0 S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/4 S6(config-if)#span por S6(config-if)#span portf S6(config-if)#span portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/4 but will only have effect when the interface is in a non-trunking mode. S6(config-if)# RACK1AS>4 [Resuming connection 4 to r4 ... ] R4(co R4(config-if)#no shut R4(config-if)# *Mar 1 08:49:18.897: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 08:49:19.897: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R4(config-if)# *Mar 1 08:49:25.961: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.224, hostname R4 R4(config-if)# R4(config-if)# R4(config-if)# R4(config-if)#^Z R4# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(dhcp-config)#^Z R3# *Mar 1 08:47:06.627: %SYS-5-CONFIG_I: Configured from console by console R3#sh run *Mar 1 08:47:09.352: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3#sh run | b ip dhcp ip dhcp excluded-address 180.40.7.129 ip dhcp excluded-address 180.40.7.131 180.40.7.132 ! ip dhcp pool Prob11 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 dns-server 208.28.1.82 domain-name bassconsulting.com option 150 ip 20.20.20.20 ! ip dhcp pool R4 host 180.40.7.130 255.255.255.224 client-identifier 0063.6973.636f.2d30.3033.302e.3835.6633.2e37.3032.302d.4661.302f.30 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! ! ! --More--   R3# RACK1AS>4 [Resuming connection 4 to r4 ... ] *Mar 1 R4#sh run int fa0/0 Building configuration... Current configuration : 75 bytes ! interface FastEthernet0/0 ip address dhcp duplex auto speed auto end R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES DHCP up up ATM1/0 unassigned YES unset administratively down down Loopback0 100.1.1.1 YES manual up up R4# R4# RACK1AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa 0/1 R2(config-if)#ip hel R2(config-if)#ip help R2(config-if)#ip helper-address 208.20.1.99 R2(config-if)# RACK1AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 0/0.2 ^ % Invalid input detected at '^' marker. R7(config)#int s 0/0.20/0.2 1/0.2 R7(config-subif)#ip helper-address 208.20.1.99 R7(config-subif)#do sh run int s 1/0.2 Building configuration... Current configuration : 239 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.20.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 end R7(config-subif)#frame-relay interface-dlci 702 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R7(config-subif)#frame-relay interface-dlci 702 pro R7(config-subif)#frame-relay interface-dlci 702 protocol ? A.B.C.D Protocol specific address ip IP R7(config-subif)#frame-relay interface-dlci 702 protocol ip ? A.B.C.D Protocol specific address R7(config-subif)#frame-relay interface-dlci 702 protocol ip 180.40.7.162 ? R7(config-subif)#frame-relay interface-dlci 702 protocol ip 180.40.7.162 %Can't add another VC to point-to-point subinterface R7(config-fr-dlci)#no frame-relay interface-dlci 702 R7(config-subif)#no frame-relay interface-dlci 702 *Mar 1 08:54:56.566: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-subif)#no frame-relay interface-dlci 702frame-relay interface-dlci 702 protocol ip 180.40.7.162 R7(config-fr-dlci)# R7(config-fr-dlci)# R7(config-fr-dlci)# R7(config-fr-dlci)# *Mar 1 08:55:12.700: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7(config-fr-dlci)#^Z R7# *Mar 1 08:57:18.575: %SYS-5-CONFIG_I: Configured from console by console R7# RACK1AS>2 [Resuming connection 2 to r2 ... ] *Ma R2(config-if)#^Z R2#sh run in *Mar 1 08:58:18.008: %SYS-5-CONFIG_I: Configured from console by console R2#sh run int fa 0/1 Building configuration... Current configuration : 125 bytes ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.20.1.99 duplex auto speed auto end R2# RACK1AS>6 7 [Resuming connection 7 to r7 ... ] R7#sh run int s 1/0.2 Building configuration... Current configuration : 261 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.20.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 end R7# R7#sh run int fa 0/1 Building configuration... Current configuration : 152 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 1 ip 180.40.7.132 service-policy output Prob6 end R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#no    uin   int fa 0- /1 R7(config-if)#no vrrp 1 ip 180.40.7.132 R7(config-if)# *Mar 1 08:59:04.132: %VRRP-6-STATECHANGE: Fa0/1 Grp 1 state Backup -> Disable R7(config-if)# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int fa 0/ % Incomplete command. R3#sh run int fa 0/0 Building configuration... Current configuration : 171 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 1 ip 180.40.7.132 vrrp 1 priority 150 end R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#intn  fa 0/0 R3(config-if)#no vrrp 1 ip 180.40.7.132 R3(config-if)#no *Mar 1 09:00:05.889: %VRRP-6-STATECHANGE: Fa0/0 Grp 1 state Master -> Disable R3(config-if)#no vrrp 1 priority 150 R3(config-if)#exitr ^ % Invalid input detected at '^' marker. R3(config-if)#exity ^ % Invalid input detected at '^' marker. R3(config-if)#exit R3(config)#sh run | i track ^ % Invalid input detected at '^' marker. R3(config)#sh run | i trackdsh run | i trackosh run | i track sh run | i track track 1 interface Serial1/2 line-protocol R3(config)#no track 1 interface Serial1/2 line-protocol R3(config)#track 1 ? interface Select an interface to track ip IP protocol R3(config)#track 1 ip ? route IP route R3(config)#track 1 ip route ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R3(config)#track 1 ip route 20.10.10 .0? / IP prefix mask R3(config)#track 1 ip route 20.10.1.0/24 ? metric Route metric reachability Route reachability state R3(config)#track 1 ip route 20.10.1.0/24 re R3(config)#track 1 ip route 20.10.1.0/24 reachability ? R3(config)#track 1 ip route 20.10.1.0/24 reachability R3(config-track)# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#track 1 ip route 20.10.1.0/24 reachability R7(config-track)#int fa 0/0 R7(config-if)#int fa 0/0 1 R7(config-if)#gl R7(config-if)#glbp ? <0-1023> Group number R7(config-if)#glbp 12    ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 1 ip ? A.B.C.D Virtual IP address R7(config-if)#glbp 1 ip 180.40.7.132 ? secondary Make this IP address a secondary address R7(config-if)#glbp 1 ip 180.40.7.132 R7(config-if)#glbp 1 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 1 for R7(config-if)#glbp 1 forwarder ? preempt Overthrow lower priority active forwarders R7(config-if)#glbp 1 forwarder           wei R7(config-if)#glbp 1 weighting ? <1-254> Weighting maximum value track Interface tracking R7(config-if)#glbp 1 weighting *Mar 1 09:01:37.820: %GLBP-6-STATECHANGE: FastEthernet0/1 Grp 1 state Standby -> Active R7(config-if)#glbp 1 weighting tr R7(config-if)#glbp 1 weighting track ? <1-500> Tracked object R7(config-if)#glbp 1 weighting track 1 ? decrement Weighting decrement R7(config-if)#glbp 1 weighting track 1 dec ? <1-255> Decrement value R7(config-if)#glbp 1 weighting track 1 dec *Mar 1 09:01:47.820: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 1 Fwd 1 state Listen -> Active R7(config-if)#glbp 1 weighting track 1 dec  50 R7(config-if)# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3(config-track)#int fa 0/0 R3(config-if)#glbp 1 ip 180.40.7.132 R3(config-if)#glbp 1 weighting track 1 dec 50 R3(config-if)# *Mar 1 09:03:33.814: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 1 Fwd 2 state Listen -> Active R3(config-if)#^Z R3#sh gl R3#sh glbp *Mar 1 09:09:27.738: %SYS-5-CONFIG_I: Configured from console by console R3#sh glbp ? BVI Bridge-Group Virtual Interface FastEthernet FastEthernet IEEE 802.3 Port-channel Ethernet Channel of interfaces active Groups in active state brief Brief output capability GLBP capability disabled Groups in disabled state init Groups in init state listen Groups in listen state standby Groups in standby or speak states | Output modifiers R3#sh glbp bri R3#sh glbp brief Interface Grp Fwd Pri State Address Active router Standby router Fa0/0 1 - 100 Standby 180.40.7.132 180.40.7.131 local Fa0/0 1 1 7 Listen 0007.b400.0101 180.40.7.131 - Fa0/0 1 2 7 Active 0007.b400.0102 local - R3#\\\\     R3# R3# R3# R3# R3# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#^Z R7# *Mar 1 09:09:42.658: %SYS-5-CONFIG_I: Configured from console by console R7#sh glbp brie Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local 180.40.7.129 Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Listen 0007.b400.0102 180.40.7.129 - R7# R7# R7# R7# R7# R7#conbfig t ^ % Invalid input detected at '^' marker. R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0 R7(config-if)#shgut   ut R7(config-if)#^Z R7# *Mar 1 09:11:14.649: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/0.1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 09:11:14.649: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 09:11:15.551: %SYS-5-CONFIG_I: Configured from console by console R7# *Mar 1 09:11:16.644: %LINK-5-CHANGED: Interface Serial1/0, changed state to administratively down *Mar 1 09:11:17.646: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to down R7#config t sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:00:04, FastEthernet0/1 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 00:00:04, FastEthernet0/1 O 20.10.1.0 [110/783] via 180.40.7.129, 00:00:04, FastEthernet0/1 C 208.28.1.0/24 is directly connected, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/1 O 180.40.7.162/32 [110/782] via 180.40.7.129, 00:00:05, FastEthernet0/1 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:05, FastEthernet0/1 O 180.40.7.67/32 [110/782] via 180.40.7.129, 00:00:05, FastEthernet0/1 O 180.40.7.66/32 [110/1] via 180.40.7.129, 00:00:05, FastEthernet0/1 R7#sh ip routeconfig t bfig tsh glbp brie Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local 180.40.7.129 Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Listen 0007.b400.0102 180.40.7.129 - R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#do sh run | b router router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 100 permit tcp host 208.28.1.2 any eq telnet access-list 101 permit ip host 208.28.1.2 any priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! ! ! ! ! ! ! ! line con 0 --More--   R7(config)#no router ospf 1 R7(config)# *Mar 1 09:12:43.455: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 09:12:43.455: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/1 from EXSTART to DOWN, Neighbor Down: Interface down or detached *Mar 1 09:12:43.459: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config)#dop    sh glb bri Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local 180.40.7.129 Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Listen 0007.b400.0102 180.40.7.129 - R7(config)# R7(config)# R7(config)# R7(config)#do sh glb bri Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local 180.40.7.129 Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Listen 0007.b400.0102 180.40.7.129 - R7(config)#do sh run int fa 0/1 Building configuration... Current configuration : 191 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 50 service-policy output Prob6 end R7(config)#do sh run int fa 0/1 Building configuration... Current configuration : 191 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 50 service-policy output Prob6 end R7(config)#do sh run int fa 0/1glb bri  Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local 180.40.7.129 Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Listen 0007.b400.0102 180.40.7.129 - R7(config)# R7(config)# R7(config)# R7(config)#do sh glb bri do sh uo  ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set C 208.28.1.0/24 is directly connected, FastEthernet0/0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/1 R7(config)# R7(config)# R7(config)# R7(config)#do sh ip routeglb bri  Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local 180.40.7.129 Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Listen 0007.b400.0102 180.40.7.129 - R7(config)#int fa 0/1 R7(config-if)#int fa 0/1do sh glb briip routeglb bri run int fa 0/1glb bri no router ospf 1do sh run | b routershut do sh run | b routerno router ospf 1 do sh glb bri run int fa 0/1 Building configuration... Current configuration : 191 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 50 service-policy output Prob6 end R7(config-if)#glbp 1 weighting track 1 decrement 7 R7(config-if)#glbp ? <0-1023> Group number R7(config-if)#glbp 1 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 1 for ? preempt Overthrow lower priority active forwarders R7(config-if)#glbp 1 for pre ? delay Wait before preempting R7(config-if)#glbp 1 for pre R7(config-if)#glbp 1 for pre weighting track 1 decrement 7for pre nglbp 1 for pre oglbp 1 for pre  glbp 1 for pre  R7(config-if)#no glbp 1 for pre  glbp 1 for pre weighting track 1 decrement 7                     ? <1-254> Weighting maximum value track Interface tracking R7(config-if)#glbp 1 weighting                  do sh glb brie Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local 180.40.7.129 Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Listen 0007.b400.0102 180.40.7.129 - R7(config-if)#router ospf 1 R7(config-router)# log-adjacency-changes R7(config-router)# network 0.0.0.0 255.255.255.255 area 0 R7(config-router)#int s 1/0 R7(config-if)# *Mar 1 09:16:10.879: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/1 from LOADING to FULL, Loading Done *Mar 1 09:16:10.883: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/1 from LOADING to FULL, Loading Done R7(config-if)#no shut R7(config-if)#^Z R7# *Mar 1 09:16:14.364: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 09:16:15.478: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up R7# *Mar 1 09:16:15.987: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 09:16:16.480: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up R7# *Mar 1 09:16:55.852: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done *Mar 1 09:16:55.881: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/0.1 from LOADING to FULL, Loading Done R7#sh run |          deb glb ? errors GLBP errors events GLBP events packets GLBP packets terse Display limited range of GLBP errors, events and packets R7#deb glb ev GLBP Events debugging is on R7#deb glb ev    config tdeb glb ev      GLBP debugging is on R7# *Mar 1 09:17:31.599: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:32.168: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#no *Mar 1 09:17:34.600: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:35.169: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)#no *Mar 1 09:17:37.601: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:38.170: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)#no *Mar 1 09:17:40.602: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:41.171: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)#no *Mar 1 09:17:43.603: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:44.172: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)#no router ospf 1 *Mar 1 09:17:46.604: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:47.173: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)# *Mar 1 09:17:49.609: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:50.174: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 *Mar 1 09:17:50.270: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 09:17:50.270: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/0.1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 09:17:50.270: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 09:17:50.274: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 09:17:50.278: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on FastEthernet0/0 from R7(config)# FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 09:17:50.290: GLBP: Fa0/1 API MAC address update R7(config)# *Mar 1 09:17:52.606: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:53.174: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)# *Mar 1 09:17:55.606: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:56.175: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 *Mar 1 09:17:56.304: GLBP: Fa0/1 1 Track 1 object changed, state Up -> Down *Mar 1 09:17:56.304: GLBP: Fa0/1 1 Weighting 100 -> 93 R7(config)# *Mar 1 09:17:58.607: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:17:59.176: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)#u all ^ % Invalid input detected at '^' marker. R7(config)# *Mar 1 09:18:01.608: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:18:02.177: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)# *Mar 1 09:18:04.609: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:18:05.178: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)# *Mar 1 09:18:07.606: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:18:08.179: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)#do u all All possible debugging has been turned off R7(config)# *Mar 1 09:18:10.607: GLBP: Fa0/1 Grp 1 Hello in 180.40.7.129 VG Standby pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 2 Active pri 167 vMAC 0007.b400.0102 *Mar 1 09:18:11.180: GLBP: Fa0/1 Grp 1 Hello out 180.40.7.131 VG Active pri 100 vIP 180.40.7.132 hello 3000, hold 10000 VF 1 Active pri 167 vMAC 0007.b400.0101 R7(config)#do sh glb brie Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local 180.40.7.129 Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Listen 0007.b400.0102 180.40.7.129 - R7(config)# RACK1AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh gl berie    rie Interface Grp Fwd Pri State Address Active router Standby router Fa0/0 1 - 100 Standby 180.40.7.132 180.40.7.131 local Fa0/0 1 1 7 Listen 0007.b400.0101 180.40.7.131 - Fa0/0 1 2 7 Active 0007.b400.0102 local - R3# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7(config)#router ospf 1 R7(config-router)#network 0.0.0.0 255.255.255.255 area 0 R7(config-router)# *Mar 1 09:20:02.983: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7(config-router)#^Z R7# *Mar 1 09:20:05.988: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.2 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 09:20:06.517: %SYS-5-CONFIG_I: Configured from console by console R7# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# *Mar 1 09:20:56.351: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 09:20:56.755: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on Serial1/0 from LOADING to FULL, Loading Done R3(config)#int fa 0/0 R3(config-if)#shut R3(config-if)# *Mar 1 09:21:02.693: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 1 Fwd 2 state Active -> Init R3(config-if)# RACK1AS>7 [Resuming connection 7 to r7 ... ] *M R7#config tdeb glb  ev config t sh glbp brie Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local 180.40.7.129 Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Listen 0007.b400.0102 180.40.7.129 - R7#sh glbp brie Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local unknown Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Active 0007.b400.0102 local - R7# *Mar 1 09:20:26.642: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 1 Fwd 2 state Listen -> Active R7#sh glbp brie Interface Grp Fwd Pri State Address Active router Standby router Fa0/1 1 - 100 Active 180.40.7.132 local unknown Fa0/1 1 1 7 Active 0007.b400.0101 local - Fa0/1 1 2 7 Active 0007.b400.0102 local - R7# R7# R7# R7# R7# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-if)#no hs  shut R3(config-if)#^Z R3# *Mar 1 09:21:43.784: %SYS-5-CONFIG_I: Configured from console by console R3#sh run *Mar 1 09:21:45.411: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 09:21:46.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3#sh run | b track track 1 ip route 20.10.1.0 255.255.255.0 reachability ! ! ! class-map match-all telnet match protocol telnet class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 ! ! ! ! ! ! --More--  interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 50 ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 --More-- *Mar 1 09:22:02.948: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 1 Fwd 1 state Listen -> Active *Mar 1 09:22:02.948: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 1 Fwd 2 state Listen -> Active --More--   R3# *Mar 1 09:22:12.948: %GLBP-6-STATECHANGE: FastEthernet0/0 Grp 1 state Standby -> Active R3# RACK1AS>7 [Resuming connection 7 to r7 ... ] *-FWDSTATECHANGE: FastEthernet0/1 Grp 1 Fwd 2 state Active -> Listen R7# R7#sh run | b track track 1 ip route 20.10.1.0 255.255.255.0 reachability ! ! ! class-map match-all S5Other match access-group 101 class-map match-all S5Telnet match access-group 100 ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 bandwidth 5000 ! ! ! ! ! ! --More--  interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 7 no glbp 1 forwarder preempt service-policy output Prob6 ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point --More-- *Mar 1 09:21:47.551: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/1 from LOADING to FULL, Loading Done --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#do sh run | b class class-map match-all S5Other match access-group 101 class-map match-all S5Telnet match access-group 100 ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 bandwidth 5000 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex --More--   R7(config)#class FTP ^ % Invalid input detected at '^' marker. R7(config)#class FTP- FTPm FTPa FTP FTP a FTPp FTP R7(config-cmap)#match pro R7(config-cmap)#match protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 --More--   R7(config-cmap)#match protocol tp  ftp R7(config-cmap)#exit R7(config)#class R7(config)#class-map tE4LN     Telnet R7(config-cmap)#match pro telnet R7(config-cmap)#int   exit R7(config)#pol R7(config)#policy-map ProbsOption           Optional R7(config-pmap)#class FTP R7(config-pmap-c)#ban per 50 R7(config-pmap-c)#class Telnet R7(config-pmap-c)#band per 25 R7(config-pmap-c)#int fa 0/1 R7(config-if)#serv R7(config-if)#service-policy out Optional Policy map Prob6 is already attached R7(config-if)#no ser i out Prob6 R7(config-if)#no ser out Prob6service-policy out Optional R7(config-if)#^Z R7#sh *Mar 1 09:24:36.071: %SYS-5-CONFIG_I: Configured from console by console R7#sh serv int fa 0/1 ^ % Invalid input detected at '^' marker. R7#sh serv int fa 0/11 int fa 0/1  int fa 0/1  int fa 0/1  int fa 0/1 p int fa 0/1o int fa 0/1l int fa 0/1 FastEthernet0/1 Service-policy output: Optional Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth 50 (%) Bandwidth 50000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 15 packets, 1677 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R7#sh run | b class class-map match-all S5Other match access-group 101 class-map match-all Telnet match protocol telnet class-map match-all FTP match protocol ftp class-map match-all S5Telnet match access-group 100 ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 bandwidth 5000 policy-map Optional class FTP bandwidth percent 50 class Telnet bandwidth percent 25 ! --More--  ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 7 no glbp 1 forwarder preempt service-policy output Optional ! --More--  interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.20.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pol Optional R7(config-pmap)#class CFTP    FTO % class map FTO not configured R7(config-pmap)#class FTO P R7(config-pmap-c)#ban per 25 R7(config-pmap-c)#^Z R7# *Mar 1 09:26:22.950: %SYS-5-CONFIG_I: Configured from console by console R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#class SQL ^ % Invalid input detected at '^' marker. R7(config)#class SQL- SQLm SQLa SQLp SQL R7(config-cmap)#match pro R7(config-cmap)#match protocol s? secure-ftp secure-http secure-imap secure-irc secure-ldap secure-nntp secure-pop3 secure-telnet smtp snapshot snmp socks sqlnet sqlserver ssh streamwork stun sunrpc syslog R7(config-cmap)#match protocol ssqlserverqlserver  R7(config-cmap)#match protocol sqlserverclass-map SQL  SQL ban per 25class FTP Opol Optional R7(config-pmap)#class sql % class map sql not configured R7(config-pmap)#class sql   SQL R7(config-pmap-c)#pri R7(config-pmap-c)#priority ? <8-2000000> Kilo Bits per second percent % of total bandwidth R7(config-pmap-c)#priority          exit R7(config-pmap)#exit R7(config)#class R7(config)#class-map SQL R7(config-cmap)#mat ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R7(config-cmap)#mat ip ? dscp Match IP DSCP (DiffServ CodePoints) precedence Match IP precedence rtp Match RTP port nos R7(config-cmap)#mat ip        exit R7(config)#access-list 100               do sh access-list Extended IP access list 100 10 permit tcp host 208.28.1.2 any eq telnet Extended IP access list 101 10 permit ip host 208.28.1.2 any R7(config)#access-list 102 ip    per ip any host 8 87.23.1.12   1.123 R7(config)#class R7(config)#class-map SQL R7(config-cmap)#match acc 102 R7(config-cmap)#exi R7(config)#do sh class Class Map match-all S5Other (id 2) Match access-group 101 Class Map match-all Telnet (id 4) Match protocol telnet Class Map match-any class-default (id 0) Match any Class Map match-all FTP (id 3) Match protocol ftp Class Map match-all S5Telnet (id 1) Match access-group 100 Class Map match-all SQL (id 5) Match protocol sqlserver Match access-group 102 R7(config)#pol Opy tiol  onal R7(config-pmap)#class SQL R7(config-pmap-c)#pr R7(config-pmap-c)#priority ? <8-2000000> Kilo Bits per second percent % of total bandwidth R7(config-pmap-c)#priority 57 6000 ? <32-2000000> Burst in bytes R7(config-pmap-c)#priority 56000 128 Minimum burst that can supported is 28000 R7(config-pmap-c)#priority 56000 1280 128  128  128  R7(config-pmap-c)#^Z R7# *Mar 1 09:32:58.298: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b class class-map match-all S5Other match access-group 101 class-map match-all Telnet match protocol telnet class-map match-all FTP match protocol ftp class-map match-all S5Telnet match access-group 100 class-map match-all SQL match protocol sqlserver match access-group 102 ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 bandwidth 5000 policy-map Optional class FTP bandwidth percent 25 --More--   class Telnet bandwidth percent 25 class SQL priority 56 128 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex --More--   glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 7 no glbp 1 forwarder preempt service-policy output Optional ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.20.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pol R7(config)#policy-map Optional R7(config-pmap)#class FTP R7(config-pmap-c)#ba R7(config-pmap-c)#bandwidth ? <8-2000000> Kilo Bits per second percent % of total Bandwidth remaining % of the remaining bandwidth R7(config-pmap-c)#bandwidth rem R7(config-pmap-c)#bandwidth remaining ? percent % of the remaining bandwidth R7(config-pmap-c)#bandwidth remaining per 25 All classes with bandwidth should have consistent units R7(config-pmap-c)#int   class Telnet R7(config-pmap-c)#class Telnetbandwidth remaining per 25 All classes with bandwidth should have consistent units R7(config-pmap-c)#do sh run | b pol policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 bandwidth 5000 policy-map Optional class FTP bandwidth percent 25 class Telnet bandwidth percent 25 class SQL priority 56 128 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto --More--   R7(config-pmap-c)#no bandwidth percent 25 R7(config-pmap-c)#no bandwidth percent 25do sh run | b pol no bandwidth percent 25 class FTP R7(config-pmap-c)#class FTPno bandwidth percent 25 R7(config-pmap-c)#no bandwidth percent 25class FTP no bandwidth percent 25do sh run | b pol bandwidth remaining per 25class Telnet bandwidth remaining per 25 R7(config-pmap-c)#bandwidth remaining per 25no bandwidth percent 25 class FTP no bandwidth percent 25do sh run | b pol bandwidth remaining per 25class Telnet  R7(config-pmap-c)#class Telnetbandwidth remaining per 25 R7(config-pmap-c)#^Z R7#sh pol *Mar 1 09:37:16.818: %SYS-5-CONFIG_I: Configured from console by console R7#sh pol     run | b pol policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 bandwidth 5000 policy-map Optional class FTP bandwidth remaining percent 25 class Telnet bandwidth remaining percent 25 class SQL priority 56 128 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto --More--   R7#sh poo l int fa 0/1 FastEthernet0/1 Service-policy output: Optional Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 --More--   Class-map: SQL (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 102 Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 518 packets, 52908 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R7#sh    sh run | pol ^ % Invalid input detected at '^' marker. R7#sh run | pol polb pol policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 bandwidth 5000 policy-map Optional class FTP bandwidth remaining percent 25 class Telnet bandwidth remaining percent 25 class SQL priority 56 128 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto --More--   R7#sh run acce    | i access-list 102 access-list 102 permit ip any host 87.23.11.123 R7# R7#sh run | i access-list 102b pol pol pol int fa 0/1 FastEthernet0/1 Service-policy output: Optional Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 --More--   Class-map: SQL (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 102 Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 669 packets, 68150 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pol Opt  ptional R7(config-pmap)#class class-default R7(config-pmap-c)#fa R7(config-pmap-c)#fair-queue ? <16-4096> Number Dynamic Conversation Queues R7(config-pmap-c)#fair-queue R7(config-pmap-c)#^Z R7#config t *Mar 1 09:45:03.319: %SYS-5-CONFIG_I: Configured from console by console R7#config tsh pol int fa 0/1 FastEthernet0/1 Service-policy output: Optional Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 --More--   Class-map: SQL (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 102 Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 689 packets, 70329 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 256 (total queued/total drops/no-buffer drops) 0/0/0 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#fair-queue class class-defaultpol Optional  R7(config-pmap)#pol Optionalfair-queue class class-default R7(config-pmap-c)#class class-defaultpol Optional fair-queue 512 R7(config-pmap-c)#^Z R7# *Mar 1 09:45:55.015: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b pol policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 bandwidth 5000 policy-map Optional class FTP bandwidth remaining percent 25 class Telnet bandwidth remaining percent 25 class SQL priority 56 128 class class-default fair-queue 512 ! ! ! ! ! ! interface FastEthernet0/0 --More--   R7# R7#sh pol int fa 0/1 FastEthernet0/1 Service-policy output: Optional Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 521 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 522 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 --More--   Class-map: SQL (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 102 Queueing Strict Priority Output Queue: Conversation 520 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 765 packets, 77999 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 512 (total queued/total drops/no-buffer drops) 0/0/0 R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#Pol Prob17 R7(config-pmap)#class FTP R7(config-pmap-c)#pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 256000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 256000 con R7(config-pmap-c)#police 256000 conform-action ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#police 256000 conform-action tr ? exceed-action action when rate is within conform and conform + exceed burst R7(config-pmap-c)#police 256000 conform-action tr exc  R7(config-pmap-c)#police 256000 conform-action tr exceed-action drop R7(config-pmap-c)#police 256000 conform-action tr exceed-action drop ? violate-action action when rate is greater than conform + exceed burst R7(config-pmap-c)#police 256000 conform-action tr exceed-action drop R7(config-pmap-c-police)#exit R7(config-pmap-c)#exit R7(config-pmap)#class Telnet R7(config-pmap-c)#pol R7(config-pmap-c)#police 56000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 bc    1400 ? <1000-512000000> Burst bytes be Excess burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 1400 3500 ? conform-action action when rate is less than conform burst R7(config-pmap-c)#police 56000 1400 3500 co R7(config-pmap-c)#police 56000 1400 3500 conform-action ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#police 56000 1400 3500 conform-action se R7(config-pmap-c)#police 56000 1400 3500 conform-action set-p R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 ? exceed-action action when rate is within conform and conform + exceed burst R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 e$0 1400 3500 conform-action set-prec-transmit 1 ex  R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action t se R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action set-p R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 ? violate-action action when rate is greater than conform + exceed burst R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 v R7(config-pmap-c)#$smit 1 exceed-action set-prec-transmit 0 violate-action dr R7(config-pmap-c)#$eed-action set-prec-transmit 0 violate-action drop R7(config-pmap-c-police)#exit R7(config-pmap-c)#pol R7(config-pmap-c)#police 56000 bc ? <1000-512000000> Burst bytes conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 bc                 exit R7(config-pmap)#class class-default R7(config-pmap-c)#pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police cir 51  ? <8000-2000000000> Bits per second percent % of interface bandwidth for Committed information rate R7(config-pmap-c)#police cir 512000                   qu R7(config-pmap-c)#queue-limit li R7(config-pmap-c)#queue-limit li  ? <1-4096> Packets R7(config-pmap-c)#queue-limit 100 fair-queue or bandwidth on the class is required to issue this command R7(config-pmap-c)#fai R7(config-pmap-c)#fair-queue R7(config-pmap-c)#fair-queue queue-limit 100 R7(config-pmap-c)#exit R7(config-pmap)#exit R7(config)#int s 1/0.1 R7(config-subif)#ser R7(config-subif)#service-policy Prob17oProb17uProb17tProb17 Prob17 CBWFQ : Not supported on subinterfaces R7(config-subif)#exit R7(config)#map R7(config)#map-cl R7(config)#map-class fram Prob17 R7(config-map-class)#ser R7(config-map-class)#service-policy map-class fram Prob17exit service-policy out Prob17 R7(config-map-class)#int s 1/0.1 R7(config-subif)#fram clas   Prob17 R7(config-subif)#do sh pol int s 1/0.1 R7(config-subif)#end R7#sh *Mar 1 09:55:09.789: %SYS-5-CONFIG_I: Configured from console by console R7#sh traf R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0.1 R7(config-subif)#fram traff ^ % Invalid input detected at '^' marker. R7(config-subif)#fram traffint s 1/0.1   R7(config-if)#int s 1/0fram traff R7(config-if)#end R7#config tsh traf  Interface Se1/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 701 56000 875 7000 0 125 875 - Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 703 56000 875 7000 0 125 875 - Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 702 56000 875 7000 0 125 875 - R7# *Mar 1 09:55:30.695: %SYS-5-CONFIG_I: Configured from console by console R7#  sh fram pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 2 0 0 0 Switched 0 0 0 0 Unused 0 1 0 0 DLCI = 701, DLCI USAGE = UNUSED, PVC STATUS = INACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 09:55:04, last time pvc status changed 00:39:33 --More--   DLCI = 702, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.2 input pkts 2093 output pkts 2061 in bytes 346220 out bytes 343808 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1777 out bcast bytes 312412 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 09:55:07, last time pvc status changed 00:39:26 Priority DLCI Group 1, DLCI 702 (HIGH), DLCI 702 (MEDIUM) DLCI 702 (NORMAL), DLCI 702 (LOW) --More--   --More--  DLCI = 703, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.1 --More--   --More--   input pkts 1474 output pkts 2034 in bytes 136392 --More--   out bytes 339648 dropped pkts 0 in pkts dropped 0 --More--   out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1773 out bcast bytes 310724 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 09:55:12, last time pvc status changed 00:39:31 R7#sh run int s 1/0.1 Building configuration... Current configuration : 182 bytes ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay class Prob17 frame-relay interface-dlci 703 end R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0.1 R7(config-subif)#no frame-relay class Prob17 R7(config-subif)# frame-relay interface-dlci 703 R7(config-fr-dlci)#class Prob17 R7(config-fr-dlci)#^Z R7#s *Mar 1 09:56:46.191: %SYS-5-CONFIG_I: Configured from console by console R7#sh fram pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 2 0 0 0 Switched 0 0 0 0 Unused 0 1 0 0 DLCI = 701, DLCI USAGE = UNUSED, PVC STATUS = INACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 09:56:04, last time pvc status changed 00:40:34 --More--   DLCI = 702, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.2 input pkts 2096 output pkts 2064 in bytes 346744 out bytes 344332 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1780 out bcast bytes 312936 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 09:56:06, last time pvc status changed 00:40:25 Priority DLCI Group 1, DLCI 702 (HIGH), DLCI 702 (MEDIUM) DLCI 702 (NORMAL), DLCI 702 (LOW) --More--   DLCI = 703, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.1 input pkts 1476 output pkts 2036 in bytes 136568 out bytes 339816 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1776 out bcast bytes 311248 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 09:56:07, last time pvc status changed 00:40:25 R7#sh pol R7#sh policy-map ? WORD policy-map name interface Show Qos Policy Interface | Output modifiers R7#sh policy-map Policy Map Prob6 Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class S5Other police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 Bandwidth 5000 (kbps) Max Threshold 64 (packets) Policy Map Prob17 Class FTP police cir 256000 bc 8000 conform-action transmit exceed-action drop Class Telnet police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop Class class-default Flow based Fair Queueing Bandwidth 0 (kbps) Max Threshold 100 (packets) --More--   Policy Map Optional Class FTP Bandwidth remaining 25 (%) Max Threshold 64 (packets) Class Telnet Bandwidth remaining 25 (%) Max Threshold 64 (packets) Class SQL Strict Priority Bandwidth 56 (kbps) Burst 128 (Bytes) Class class-default Flow based Fair Queueing Bandwidth 0 (kbps) Max Threshold 64 (packets) R7#q sh ser R7#sh services          pol R7#sh policy-map ? WORD policy-map name interface Show Qos Policy Interface | Output modifiers R7#sh policy-map int s 1/0.1 Serial1/0.1: DLCI 703 - Service-policy output: Prob17 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp police: cir 256000 bps, bc 8000 bytes conformed 0 packets, 0 bytes; actions: transmit exceeded 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet police: cir 56000 bps, bc 1400 bytes, be 3500 bytes conformed 0 packets, 0 bytes; actions: --More--   set-prec-transmit 1 exceeded 0 packets, 0 bytes; actions: set-prec-transmit 0 violated 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps, violate 0 bps Class-map: class-default (match-any) 3 packets, 524 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 16 (total queued/total drops/no-buffer drops) 0/0/0 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0 R7(config-if)#no fram trac ff R7(config-if)#^Z R7#config tsh policy-map int s 1/0.1 *Mar 1 09:57:49.415: %SYS-5-CONFIG_I: Configured from console by console R7#sh policy-map int s 1/0.1 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int f s 1/0 R7(config-if)#int s 1/0no fram traffno fram traff  fram traff  R7(config-if)#^Z R7# *Mar 1 09:58:04.652: %SYS-5-CONFIG_I: Configured from console by console R7#config tsh policy-map int s 1/0.1 Serial1/0.1: DLCI 703 - Service-policy output: Prob17 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp police: cir 256000 bps, bc 8000 bytes conformed 0 packets, 0 bytes; actions: transmit exceeded 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet police: cir 56000 bps, bc 1400 bytes, be 3500 bytes conformed 0 packets, 0 bytes; actions: --More--   set-prec-transmit 1 exceeded 0 packets, 0 bytes; actions: set-prec-transmit 0 violated 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps, violate 0 bps Class-map: class-default (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 16 (total queued/total drops/no-buffer drops) 0/0/0 R7#sh run | b class class-map match-all S5Other match access-group 101 class-map match-all Telnet match protocol telnet class-map match-all FTP match protocol ftp class-map match-all S5Telnet match access-group 100 class-map match-all SQL match protocol sqlserver match access-group 102 ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 bandwidth 5000 policy-map Prob17 class FTP police 256000 conform-action transmit exceed-action drop --More--   class Telnet police 56000 1400 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop class class-default fair-queue queue-limit 100 policy-map Optional class FTP bandwidth remaining percent 25 class Telnet bandwidth remaining percent 25 class SQL priority 56 128 class class-default fair-queue 512 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 --More--   speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 7 no glbp 1 forwarder preempt service-policy output Optional ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point --More--   ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 703 class Prob17 ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.20.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown --More--  ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! --More--  no ip http server no ip http secure-server ! ! map-class frame-relay Prob17 service-policy output Prob17 access-list 100 permit tcp host 208.28.1.2 any eq telnet access-list 101 permit ip host 208.28.1.2 any access-list 102 permit ip any host 87.23.11.123 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous --More--   R7# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#do sh run| b class sh run| b class ^ % Invalid input detected at '^' marker. R3(config)#do sh run| b class | b class class-map match-all telnet match protocol telnet class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto --More--   R3(config)#con   pol Prob18 R3(config-pmap)#class FTP R3(config-pmap-c)#shap R3(config-pmap-c)#shape ? adaptive Enable Traffic Shaping adaptation to BECN average configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc only per interval fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fr-voice-adapt Enable rate adjustment depending on voice presence max-buffers Set Maximum Buffer Limit peak configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc+Be per interval R3(config-pmap-c)#shape average ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R3(config-pmap-c)#shape average 256000 ? <256-154400000> bits per interval, sustained. Needs to be multiple of 128. Recommend not to configure it, the algorithm will find out the best value R3(config-pmap-c)#shape average 256000 R3(config-pmap-c)#exit R3(config-pmap)#class telnet R3(config-pmap-c)#class telnet class telnetexit shape average 256000        56000 R3(config-pmap-c)#exit R3(config-pmap)#class class-default R3(config-pmap-c)#? QoS policy-map class configuration commands: bandwidth Bandwidth compression Activate Compression drop Drop all packets exit Exit from QoS class action configuration mode fair-queue Enable Flow-based Fair Queuing in this Class no Negate or set default values of a command police Police priority Strict Scheduling Priority for this Class queue-limit Queue Max Threshold for Tail Drop random-detect Enable Random Early Detection as drop policy service-policy Configure QoS Service Policy set Set QoS values shape Traffic Shaping R3(config-pmap-c)#sh pe R3(config-pmap-c)#sh peak ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R3(config-pmap-c)#sh peak 600000 R3(config-pmap-c)#int s 1/0 R3(config-if)#ser R3(config-if)#serv R3(config-if)#service-policy out Prob18 R3(config-if)#do sh pol int s 1.0  /0 Serial1/0 Service-policy output: Prob18 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 256000/256000 1984 7936 7936 31 992 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Traffic Shaping Target/Average Byte Sustain Excess Interval Increment --More--   Rate Limit bits/int bits/int (ms) (bytes) 56000/56000 1988 7952 7952 142 994 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no Class-map: class-default (match-any) 1 packets, 13 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 1200000/600000 3750 15000 15000 25 3750 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no R3(config-if)# do sh pol int s 1/0service-policy out Prob18int s 1/0 sh peak 600000class class-defaultexit shape average 56000class telnet exit shape average 256000 class FTP pol Prob18 R3(config-pmap)#pol Prob18do sh pol int s 1/0service-policy out Prob18int s 1/0 sh peak 600000class class-default R3(config-pmap-c)#class class-defaultpol Prob18 do sh pol int s 1/0service-policy out Prob18int s 1/0 sh peak 600000nsh peak 600000osh peak 600000 sh peak 600000 R3(config-pmap-c)#pol R3(config-pmap-c)#police ci R3(config-pmap-c)#police cir 512000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R3(config-pmap-c)#police cir 512000 oir     pir ? <8000-2000000000> Bits per second R3(config-pmap-c)#police cir 512000 pir 60000  000 R3(config-pmap-c-police)#do sh pol int s 1/0 Serial1/0 Service-policy output: Prob18 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Class-map: class-default (match-any) 16 packets, 658 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any police: cir 512000 bps, bc 16000 bytes pir 600000 bps, be 18750 bytes conformed 0 packets, 0 bytes; actions: transmit --More--   exceeded 0 packets, 0 bytes; actions: drop violated 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps, violate 0 bps R3(config-pmap-c-police)# R3(config-pmap-c-police)# R3(config-pmap-c-police)# R3(config-pmap-c-police)#end R3#sh run | *Mar 1 10:09:09.954: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b class class-map match-all telnet match protocol telnet class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 policy-map Prob18 class FTP shape average 256000 class telnet shape average 56000 class class-default police cir 512000 pir 600000 ! ! ! --More--  ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 50 ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 --More--   encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast service-policy output Prob18 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown --More--   R3# RACK1AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh run int s       | b inbterface serak l         Serial  11~  /0 R2#sh run | b inbterface Serial1/0terface Serial1/0  interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob4 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 --More--   ip address 180.40.7.2 255.255.255.224 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! --More--  router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! ! map-class frame-relay Prob4 frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn access-list 100 deny ospf any any access-list 100 permit ip any any ! ! ! ! ! ! --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)#fram class Prob4 R2(config-subif)#exit R2(config)#^Z R2# *Mar 1 10:13:28.522: %SYS-5-CONFIG_I: Configured from console by console R2# R2# R2# RACK1AS>5 [Resuming connection 5 to r5 ... ] 09: S5(config)#vlass   an 99 S5(config-vlan)#name Voice S5(config-vlan)#? VLAN configuration commands: are Maximum number of All Route Explorer hops for this VLAN (or zero if none specified) backupcrf Backup CRF mode of the VLAN bridge Bridging characteristics of the VLAN exit Apply changes, bump revision number, and exit mode media Media type of the VLAN mtu VLAN Maximum Transmission Unit name Ascii name of the VLAN no Negate a command or set its defaults parent ID number of the Parent VLAN of FDDI or Token Ring type VLANs private-vlan Configure a private VLAN remote-span Configure as Remote SPAN VLAN ring Ring number of FDDI or Token Ring type VLANs said IEEE 802.10 SAID shutdown Shutdown VLAN switching state Operational state of the VLAN ste Maximum number of Spanning Tree Explorer hops for this VLAN (or zero if none specified) stp Spanning tree characteristics of the VLAN tb-vlan1 ID number of the first translational VLAN for this VLAN (or zero if none) --More--   tb-vlan2 ID number of the second translational VLAN for this VLAN (or zero if none) S5(config-vlan)#exit S5(config)#int fa 0/21 S5(config-if)#swi S5(config-if)#switchport vo S5(config-if)#switchport voice vl S5(config-if)#switchport voice vlan ? <1-4094> Vlan for voice traffic dot1p Priority tagged on PVID none Don't tell telephone about voice vlan untagged Untagged on PVID S5(config-if)#switchport voice vlan 9 ? S5(config-if)#switchport voice vlan 9  ( 9 S5(config-if)#switch tru S5(config-if)#switch trunk ? allowed Set allowed VLAN characteristics when interface is in trunking mode encapsulation Set trunking encapsulation when interface is in trunking mode native Set trunking native characteristics when interface is in trunking mode pruning Set pruning VLAN characteristics when interface is in trunking mode S5(config-if)#switch trunk       more  de tru S5(config-if)#switch mode trunk Command rejected: An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode. S5(config-if)#do sh int s fa 0/21 sw Name: Fa0/21 Switchport: Enabled Administrative Mode: dynamic desirable Operational Mode: down Administrative Trunking Encapsulation: negotiate Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: 99 (Voice) Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL --More--   S5(config-if)#switch trun en dot` S5(config-if)#switch trun en dot`  S5(config-if)#switch trun en dot1q S5(config-if)#switch trun en dot1q do sh int fa 0/21 sw switch mode trunk port voice vlan 99 mode trunk  S5(config-if)#swi S5(config-if)#switchport ? access Set access mode characteristics of the interface block Disable forwarding of unknown uni/multi cast addresses host Set port host mode Set trunking mode of the interface nonegotiate Device will not engage in negotiation protocol on this interface port-security Security related command priority Set appliance 802.1p priority protected Configure an interface to be a protected port trunk Set trunking characteristics of the interface voice Voice appliance attributes S5(config-if)#switchport pr S5(config-if)#switchport pri S5(config-if)#switchport priority ? extend Set appliance 802.1p priority S5(config-if)#switchport priority e S5(config-if)#switchport priority extend ? cos Override 802.1p priority of devices on appliance trust Trust 802.1p priorities of devices on appliance S5(config-if)#switchport priority extend co S5(config-if)#switchport priority extend cos ? <0-7> Priority for devices on appliance S5(config-if)#switchport priority extend cos 1 ? S5(config-if)#switchport priority extend cos 1 S5(config-if)#mls qos S5(config-if)#mls qos tru S5(config-if)#mls qos trust ? cos Classify by packet COS device trusted device class dscp Classify by packet DSCP ip-precedence Classify by packet IP precedence S5(config-if)#mls qos trust cl po  os    S5(config-if)#exit S5(config)#mls qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S5(config)#exit S5#sh 10:24:39: %SYS-5-CONFIG_I: Configured from console by console S5#sh run | b     int fa 0/21 Building configuration... Current configuration : 199 bytes ! interface FastEthernet0/21 switchport trunk encapsulation dot1q switchport mode trunk switchport voice vlan 99 switchport priority extend cos 1 mls qos trust dscp spanning-tree portfast end S5#sh riun     un | i mls mls qos mls qos trust dscp S5# S5# RACK1AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#class   R4(config)#class-map web R4(config-cmap)#match pro R4(config-cmap)#match protocol h? http R4(config-cmap)#match protocol http R4(config-cmap)#exit R4(config)#clas R4(config)#class-map ping R4(config-cmap)#match pro ? arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 dhcp Dynamic Host Configuration dlsw Data Link Switching (Direct encapsulation only) dns Domain Name Server lookup egp Exterior Gateway Protocol --More--   eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) ipsec IP Security Protocol (ESP/AH) ipv6 IPV6 irc Internet Relay Chat kazaa2 Kazaa Version 2 kerberos Kerberos l2tp L2F/L2TP tunnel ldap Lightweight Directory Access Protocol llc2 llc2 napster Napster Traffic netbios NetBIOS --More--   netshow Microsoft Netshow nfs Network File System nntp Network News Transfer Protocol notes Lotus Notes(R) novadigm Novadigm EDM ntp Network Time Protocol pad PAD links pcanywhere Symantec pcANYWHERE pop3 Post Office Protocol pppoe PPP over Ethernet pptp Point-to-Point Tunneling Protocol printer print spooler/lpd qllc qllc protocol rcmd BSD r-commands (rsh, rlogin, rexec) rip Routing Information Protocol rsrb Remote Source-Route Bridging rsvp Resource Reservation Protocol rtp Real Time Protocol rtspplayer RTSP players streaming protocol secure-ftp FTP over TLS/SSL secure-http Secured HTTP secure-imap Internet Message Access Protocol over TLS/SSL secure-irc Internet Relay Chat over TLS/SSL --More--   secure-ldap Lightweight Directory Access Protocol over TLS/SSL secure-nntp Network News Transfer Protocol over TLS/SSL secure-pop3 Post Office Protocol over TLS/SSL secure-telnet Telnet over TLS/SSL smtp Simple Mail Transfer Protocol snapshot Snapshot routing support snmp Simple Network Management Protocol socks SOCKS sqlnet SQL*NET for Oracle sqlserver MS SQL Server ssh Secured Shell streamwork Xing Technology StreamWorks player stun Serial Tunnel sunrpc Sun RPC syslog System Logging Utility telnet Telnet tftp Trivial File Transfer Protocol vdolive VDOLive streaming video vofr voice over Frame Relay packets xwindows X-Windows remote access R4(config-cmap)#match pro           do sh run   | b   i access-list access-list 100 permit icmp any any echo R4(config-cmap)#match acc R4(config-cmap)#match access-group 100 R4(config-cmap)#exit R4(config)#class R4(config)#class-map routing R4(config-cmap)#exit R4(config)#access-list             do sh access-list Extended IP access list 100 10 permit icmp any any echo (5 matches) R4(config)#access-list 101 per ospf any any R4(config)#class \ R4(config)#class \   R4(config)#class-map routing R4(config-cmap)#match access 101 R4(config-cmap)#exit R4(config)#pol Prob21 R4(config-pmap)#class web R4(config-pmap-c)#set ? atm-clp Set ATM CLP bit to 1 cos Set IEEE 802.1Q/ISL class of service/user priority discard-class Discard behavior identifier dscp Set DSCP in IP(v4) and IPv6 packets fr-de Set FR DE bit to 1 ip Set IP specific values mpls Set MPLS specific values precedence Set precedence in IP(v4) and IPv6 packets qos-group Set QoS Group R4(config-pmap-c)#set dscp ? <0-63> Differentiated services codepoint value af11 Match packets with AF11 dscp (001010) af12 Match packets with AF12 dscp (001100) af13 Match packets with AF13 dscp (001110) af21 Match packets with AF21 dscp (010010) af22 Match packets with AF22 dscp (010100) af23 Match packets with AF23 dscp (010110) af31 Match packets with AF31 dscp (011010) af32 Match packets with AF32 dscp (011100) af33 Match packets with AF33 dscp (011110) af41 Match packets with AF41 dscp (100010) af42 Match packets with AF42 dscp (100100) af43 Match packets with AF43 dscp (100110) cos Set packet DSCP from L2 COS cs1 Match packets with CS1(precedence 1) dscp (001000) cs2 Match packets with CS2(precedence 2) dscp (010000) cs3 Match packets with CS3(precedence 3) dscp (011000) cs4 Match packets with CS4(precedence 4) dscp (100000) cs5 Match packets with CS5(precedence 5) dscp (101000) cs6 Match packets with CS6(precedence 6) dscp (110000) cs7 Match packets with CS7(precedence 7) dscp (111000) default Match packets with default dscp (000000) --More--   R4(config-pmap-c)#set dscp af21 R4(config-pmap-c)#exit R4(config-pmap)#class ping R4(config-pmap-c)#set dscp af31 R4(config-pmap-c)#exit R4(config-pmap)#class ospf      rpout    outing R4(config-pmap-c)#set dscp 43  af43 R4(config-pmap-c)#exit R4(config-pmap)#clas class-deaf   efault R4(config-pmap-c)#set dscp af12 R4(config-pmap-c)#inr   t fa 0/0 R4(config-if)#ser R4(config-if)#service-policy out Prob21 R4(config-if)#^Z R4#sh *Mar 1 10:29:09.741: %SYS-5-CONFIG_I: Configured from console by console R4#sh run| b class ^ % Invalid input detected at '^' marker. R4#sh run| b class | b class class-map match-all ping match access-group 100 class-map match-all web match protocol http class-map match-all routing match access-group 101 ! ! policy-map Prob21 class web set dscp af21 class ping set dscp af31 class routing set dscp af43 class class-default set dscp af12 ! ! ! ! ! interface Loopback0 --More--   R4# R4#sh run | b interface Fast interface FastEthernet0/0 ip address dhcp duplex auto speed auto service-policy output Prob21 ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip local policy route-map prob3 no ip http server no ip http secure-server ip classless ! ! access-list 100 permit icmp any any echo access-list 101 permit ospf any any --More--  ! route-map prob3 permit 10 match ip address 100 set ip next-hop 180.40.7.129 ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R4# R4# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3#sh run o int s 1/2 Building configuration... Current configuration : 123 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 end R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#mnpo      no ser      service-policy output Prob9 R3(config-if)#exit R3(config)#class R3(config)#class-map dscp12 R3(config-cmap)#match ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R3(config-cmap)#match dscp ? <0-63> Differentiated services codepoint value af11 Match packets with AF11 dscp (001010) af12 Match packets with AF12 dscp (001100) af13 Match packets with AF13 dscp (001110) af21 Match packets with AF21 dscp (010010) af22 Match packets with AF22 dscp (010100) af23 Match packets with AF23 dscp (010110) af31 Match packets with AF31 dscp (011010) af32 Match packets with AF32 dscp (011100) af33 Match packets with AF33 dscp (011110) af41 Match packets with AF41 dscp (100010) af42 Match packets with AF42 dscp (100100) af43 Match packets with AF43 dscp (100110) cs1 Match packets with CS1(precedence 1) dscp (001000) cs2 Match packets with CS2(precedence 2) dscp (010000) cs3 Match packets with CS3(precedence 3) dscp (011000) cs4 Match packets with CS4(precedence 4) dscp (100000) cs5 Match packets with CS5(precedence 5) dscp (101000) cs6 Match packets with CS6(precedence 6) dscp (110000) cs7 Match packets with CS7(precedence 7) dscp (111000) default Match packets with default dscp (000000) ef Match packets with EF dscp (101110) --More--   R3(config-cmap)#match dscp 2 12 R3(config-cmap)#match dscp 12class-map dscp12 8 R3(config-cmap)#class-map dscp18match dscp 12  8 R3(config-cmap)#match dscp 18class-map dscp18  26 R3(config-cmap)#class-map dscp26match dscp 18   26 R3(config-cmap)#do sh run\  \   | b class class-map match-all dscp26 match dscp af31 class-map match-all telnet match protocol telnet class-map match-all dscp12 match dscp af12 class-map match-all dscp18 match dscp af21 class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 policy-map Prob18 class FTP shape average 256000 class telnet --More--   R3(config-cmap)#pol p Prob22 R3(config-pmap)#class dscp12 R3(config-pmap-c)#ban R3(config-pmap-c)#bandwidth per R3(config-pmap-c)#bandwidth percent 15 R3(config-pmap-c)#bandwidth percent 15class dscp12  8 R3(config-pmap-c)#class dscp18bandwidth percent 15 R3(config-pmap-c)#bandwidth percent 15class dscp18   26 R3(config-pmap-c)#class dscp26bandwidth percent 15  50 R3(config-pmap-c)#int serv R3(config-pmap-c)#int serv    ser 1/2 R3(config-if)#serv out Por  rob22 R3(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 124 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob22 end R3(config-if)#max-reserved-bandwidth 100   80 Reservable bandwidth is being reduced. Some existing reservations may be terminated. R3(config-if)#exit R3(config)#exit R3# *Mar 1 10:32:31.003: %SYS-5-CONFIG_I: Configured from console by console R3#sh pol R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 (12) Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 (18) Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 (26) Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 14 packets, 1026 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK1AS>4 [Resuming connection 4 to r4 ... ] R4#ping Protocol [ip]: Target IP address: 20.10.1.         % Bad IP address R4# R4#ping 20.10.1.1 sou 1900   00.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/32 ms R4# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 (12) Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 (18) Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 (26) Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 33 packets, 2616 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK1AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/24 S5(config-if)#ml S5(config-if)#mls qo S5(config-if)#mls qos tr S5(config-if)#mls qos trust dsc S5(config-if)#mls qos trust dscp S5(config-if)#^Z S5# 10:39:16: %SYS-5-CONFIG_I: Configured from console by console S5# RACK1AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/36 ms R4# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh policy-map int s 1/2config t sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 (12) Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 (18) Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 5 packets, 520 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 (26) Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 65 packets, 4944 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#no ip routr R3(config-if)#no ip routr  R3(config-if)#no ip route- R3(config-if)#no ip route-cache R3(config-if)#int s 1/2 R3(config-if)#int s 1/2no ip route-cache R3(config-if)#\ ^Z R3# RACK1AS>4 [Resuming connection 4 to r4 ... ] ping 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms R4# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Ma.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 10:36:50.785: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 R3# R3#config tsh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 (12) Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 (18) Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 10 packets, 1040 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 (26) Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 5/520 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 75 packets, 5798 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK1AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms R4#ping 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/34/36 ms R4#ping 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/34/36 ms R4# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 10:37:51.*Mar 1 10:37:52.963: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 10:37:53.992: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 10:37:53.992: IP: route map Prob1, item 20, permit *Mar 1 10:37:53.992: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 10:37:53.992: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 10:37:54.028: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 10:37:54.028: IP: route map Prob1, item 20, permit *Mar 1 10:37:54.028: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 10:37:54.028: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 10:37:54.064: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 10:37:54.064: IP: route map Prob1, item 20, permit *Mar 1 10:37:54.064: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 10:37:54.064: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 10:37:54.100: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 10:37:54.100: IP: route map Prob1, item 20, permit *Mar 1 10:37:54.100: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 10:37:54.100: IP: FastEthernet0/0 to Serial1/2 180.40.7.2 *Mar 1 10:37:54.137: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 10:37:54.137: IP: route map Prob1, item 20, permit *Mar 1 10:37:54.137: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 10:37:54.137: IP: FastEthernet0/0 to Serial1/2 180.40.7.2R3# R3#sh policy-map int s 1/2u all ^ % Invalid input detected at '^' marker. R3# all    u all~  All possible debugging has been turned off R3#u allsh policy-map int s 1/2u all ^ % Invalid input detected at '^' marker. R3#sh policy-map int s 1/2u allu all sh policy-map int s 1/2u all config t sh policy-map int s 1/2 Serial1/2 Service-policy output: Prob22 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 (12) Queueing Output Queue: Conversation 41 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp18 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af21 (18) Queueing Output Queue: Conversation 42 Bandwidth 15 (%) Bandwidth 19 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: dscp26 (match-all) 25 packets, 2600 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af31 (26) Queueing Output Queue: Conversation 43 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 20/2080 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 93 packets, 7084 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh run | b pol policy-map Prob9 class FTP bandwidth percent 50 class telnet bandwidth percent 25 class class-default bandwidth percent 25 policy-map Prob18 class FTP shape average 256000 class telnet shape average 56000 class class-default police cir 512000 pir 600000 policy-map Prob22 class dscp12 bandwidth percent 15 class dscp18 bandwidth percent 15 class dscp26 bandwidth percent 50 ! ! --More--   R3#sh run int fa 0. /0 Building configuration... Current configuration : 231 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 no ip route-cache cef no ip route-cache ip policy route-map Prob1 duplex auto speed auto glbp 1 ip 180.40.7.132 glbp 1 weighting track 1 decrement 50 end R3#sh run int ser 1/2 Building configuration... Current configuration : 165 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 no ip route-cache cef no ip route-cache max-reserved-bandwidth 80 service-policy output Prob22 end R3# R3# R3# RACK1AS>5 [Resuming connection 5 to r5 ... ] S5#sh run int fa 0/24 Building configuration... Current configuration : 115 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk mls qos trust dscp end S5# S5#