=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.03.08 14:42:18 =~=~=~=~=~=~=~=~=~=~=~= sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.98 0 FULL/ - 00:00:35 180.40.7.2 Serial1/2 192.10.32.11 1 FULL/DR 00:00:39 180.40.7.130 FastEthernet0/1 R3#sh ip RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 17.100.1.2 1 FULL/DR 00:00:37 17.100.1.2 Ethernet0/1 180.40.7.98 0 FULL/ - 00:01:53 180.40.7.65 Serial0/0.2 17.57.100.2 1 FULL/DR 00:00:36 17.57.100.2 Ethernet0/0 R1#sh ip ospf nei   int s 0/0.1 Serial0/0.1 is up, line protocol is up Internet Address 180.40.7.34/27, Area 0 Process ID 1, Router ID 180.40.7.66, Network Type POINT_TO_POINT, Cost: 64 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 Hello due in 00:00:06 Index 2/2, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s 1/0.1 Building configuration... Current configuration : 236 bytes ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip ospf network point-to-point frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 end R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] % Incomplete command. R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ip ospf ti R3(config-if)#ip ospf ti  he R3(config-if)#ip ospf hello-interval 10 R3(config-if)#^Z R3# *Mar 1 20:46:52.557: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 20:46:55.306: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial1/0 from LOADING to FULL, Loading Done *Mar 1 20:46:55.362: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.66 on Serial1/0 from LOADING to FULL, Loading Done R3# RACK11AS>1 [Resuming connection 1 to r1 ... ] *Mar 1 R1#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 17.100.1.2 1 FULL/DR 00:00:36 17.100.1.2 Ethernet0/1 180.40.7.98 0 FULL/ - 00:01:51 180.40.7.65 Serial0/0.2 180.40.7.129 0 FULL/ - 00:00:32 180.40.7.33 Serial0/0.1 17.57.100.2 1 FULL/DR 00:00:34 17.57.100.2 Ethernet0/0 R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.57.100.0 is directly connected, Ethernet0/0 C 17.100.1.0 is directly connected, Ethernet0/1 O 192.10.32.0/24 [110/66] via 180.40.7.33, 00:00:34, Serial0/0.1 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.128/27 [110/65] via 180.40.7.33, 00:00:34, Serial0/0.1 O 180.40.7.0/27 [110/845] via 180.40.7.65, 00:00:34, Serial0/0.2 [110/845] via 180.40.7.33, 00:00:34, Serial0/0.1 O 180.40.7.33/32 [110/64] via 180.40.7.33, 00:00:35, Serial0/0.1 C 180.40.7.32/27 is directly connected, Serial0/0.1 O 180.40.7.65/32 [110/64] via 180.40.7.65, 00:00:35, Serial0/0.2 C 180.40.7.64/27 is directly connected, Serial0/0.2 O 180.40.7.96/27 [110/65] via 180.40.7.65, 00:00:35, Serial0/0.2 R1#  config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip mu R1(config)#ip multicast- R1(config)#ip multicast-routing R1(config)#int e 0/0 R1(config-if)#ip pim sp R1(config-if)#ip pim sparse-d R1(config-if)#ip pim sparse-dense-mode R1(config-if)#int e 0/0 1 R1(config-if)#int e 0/1p pim sparse-dense-mode *Mar 1 20:49:06.377: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.57.100.1 on interface Ethernet0/0 (vrf default) R1(config-if)#ip pim sparse-dense-mode R1(config-if)#int s *Mar 1 20:49:09.278: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.100.1.1 on interface Ethernet0/1 (vrf default) R1(config-if)#int s 0/0.1 R1(config-subif)#int s 0/0.1p pim sparse-dense-mode R1(config-subif)#ip pim sparse-dense-mode nt s 0/0.1  2 R1(config-subif)#int s 0/0.2p pim sparse-dense-mode R1(config-subif)#^Z R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip mu R2(config)#ip multicast- R2(config)#ip multicast-routing R2(config)#int fa 0/1 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#int s 1 *Mar 1 20:48:50.434: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.98 on interface FastEthernet0/1 (vrf default) R2(config-if)#int s 1/0.1 R2(config-subif)#int s 1/0.1p pim sparse-dense-mode R2(config-subif)#ip pim sparse-dense-mode nt s 1/0.1  2 R2(config-subif)#int s 1/0.2p pim sparse-dense-mode R2(config-subif)#int *Mar 1 20:48:55.050: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.35 on interface Serial1/0.1 (vrf default) *Mar 1 20:48:55.683: %PIM-5-NBRCHG: neighbor 180.40.7.66 UP on interface Serial1/0.2 (vrf default) *Mar 1 20:48:55.687: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.66 on interface Serial1/0.2 (vrf default) R2(config-subif)#int s 1/2 R2(config-if)#int s 1/2p pim sparse-dense-mode R2(config-if)#^Z R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#confi gt ^ % Invalid input detected at '^' marker. R3#ip mu R3#ip mu     config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip mu R3(config)#ip multicast- R3(config)#ip multicast-routing R3(config)#int s 1/0 R3(config-if)#ip pim sp R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)#int *Mar 1 20:49:20.392: %PIM-5-NBRCHG: neighbor 180.40.7.35 UP on interface Serial1/0 (vrf default) *Mar 1 20:49:20.396: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.35 on interface Serial1/0 (vrf default) *Mar 1 20:49:20.460: %PIM-5-NBRCHG: neighbor 180.40.7.34 UP on interface Serial1/0 (vrf default) R3(config-if)#int fa 0/1 R3(config-if)#int fa 0/1p pim sparse-dense-mode nt fa 0/1 p pim sparse-dense-mode R3(config-if)#int s 1? % Unrecognized command R3(config-if)#int s 12  1/2 R3(config-if)# *Mar 1 20:49:28.333: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.129 on interface FastEthernet0/1 (vrf default) R3(config-if)#int s 1/2p pim sparse-dense-mode R3(config-if)#^Z R3# *Mar 1 20:49:30.540: %PIM-5-NBRCHG: neighbor 180.40.7.2 UP on interface Serial1/2 (vrf default) R3# *Mar 1 20:49:31.702: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip mu S5(config)#ip multicast- S5(config)#ip multicast-routing S5(config)#int fa0/2 S5(config-if)#ip pim sp S5(config-if)#ip pim sp S5(config-if)#ip pim sp S5(config-if)#ip pim sp S5(config-if)#ip pim sp S5(config-if)#ip pim sp S5(config-if)#ip pim sp         int fa0/2 1 S5(config-if)#ip pim  S5(config-if)#ip pim sp S5(config-if)#ip pim sparse-d S5(config-if)#ip pim sparse-dense-mode S5(config-if)#^Z S5#^x 20:53:20: %SYS-5-CONFIG_I: Configured from console by console S5#^x6 % Unknown command or computer name, or unable to find computer address S5# S5# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip mu S6(config)#ip multicastsd  - S6(config)#ip multicast-routing S6(config)#int fa0/. 2 S6(config-if)#ip pim S6(config-if)#ip pim sp S6(config-if)#ip pim sparse-d S6(config-if)#ip pim sparse-dense-mode S6(config-if)#^Z S6#x 20:53:32: %SYS-5-CONFIG_I: Configured from console by console7 Translating "x7" % Unknown command or computer name, or unable to find computer address S6# S6# RACK11AS>7 [Resuming connection 7 to r7 ... ] * R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#oip   ip p mu R7(config)#ip multicast- R7(config)#ip multicast-routing int      R7(config)#int fa 0/1 R7(config-if)#ip pim sp R7(config-if)#ip pim sparse-d R7(config-if)#ip pim sparse-dense-mode R7(config-if)#tz RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip mu R4(config)#ip multicast- R4(config)#ip multicast-routing int fa 0/0 ^ % Invalid input detected at '^' marker. R4(config)#ip multicast-routing int fa 0/0           R4(config)#int fa 0/0 R4(config-if)#ip pim d R4(config-if)#ip pim d % Ambiguous command: "ip pim d" R4(config-if)#ip pim de R4(config-if)#ip igp  *Mar 1 20:53:42.770: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.130 on interface FastEthernet0/0 (vrf default) R4(config-if)#ip ig R4(config-if)#ip igmp jo R4(config-if)#ip igmp join-group 224.4.4.4 R4(config-if)#^Z R4# *Mar 1 20:53:49.842: %SYS-5-CONFIG_I: Configured from console by console R4# RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar ^ % Invalid input detected at '^' marker. R7(config-if)#^Z R7# R7# R7# R7# *Mar 1 20:51:24.852: %SYS-5-CONFIG_I: Configured from console by console R7#ping 224.. 4,4  .4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 72 ms Reply to request 0 from 180.40.7.130, 136 ms Reply to request 0 from 180.40.7.130, 116 ms R7#^x  1 sh run | b ip mu ip multicast-routing ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 --More--   no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 17.100.1.2 255.255.255.0 ip pim sparse-dense-mode duplex auto speed auto ! interface Serial1/0 no ip address shutdown ! interface Serial1/1 no ip address shutdown ! --More--   R7# RACK11AS>4 [Resuming connection 4 to r4 ... ] *M R4#sh run int fa 0/0 Building configuration... Current configuration : 163 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4# R4#^x7 % Unknown command or computer name, or unable to find computer address R4# R4# RACK11AS>8 7 [Resuming connection 7 to r7 ... ] R7#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:03:27/00:02:55, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:03:27/00:00:00 R7# RACK11AS>2 [Resuming connection 2 to r2 ... ] *M R2#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 40 ms Reply to request 0 from 180.40.7.130, 136 ms Reply to request 0 from 180.40.7.130, 108 ms Reply to request 0 from 180.40.7.130, 84 ms R2#m tr  m? microcode modemui monitor more mpls mpoa mrinfo mrm mstat mtrace R2#mtra ? Hostname or A.B.C.D Source to trace route from vrf Select VPN Routing/Forwarding instance R2#mtra      trace 32  224.4.4.44  4 Type escape sequence to abort. Tracing the route to 224.4.4.4 1 * * * 2 * * * 3 R2#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:04:33/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:04:33/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:04:33/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:04:33/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:04:33/00:00:00 (180.40.7.2, 224.4.4.4), 00:01:04/00:02:53, flags: Incoming interface: Serial1/2, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:04/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:01:04/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:01:04/00:00:00 (180.40.7.35, 224.4.4.4), 00:01:04/00:02:53, flags: Incoming interface: Serial1/0.1, RPF nbr 0.0.0.0 Outgoing interface list: --More--   FastEthernet0/1, Forward/Sparse-Dense, 00:01:04/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:02:01/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:02:01/00:00:00 (180.40.7.65, 224.4.4.4), 00:02:00/00:01:56, flags: Incoming interface: Serial1/0.2, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:02:00/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:02:00/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:02:00/00:00:00 (*, 224.0.1.40), 00:08:20/00:02:51, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:07:35/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:07:45/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:08:13/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:08:20/00:00:00 R2#sh ip mroutetrace 224.4.4.4ping 224.4.4.4  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 32 ms Reply to request 0 from 180.40.7.130, 168 ms Reply to request 0 from 180.40.7.130, 156 ms Reply to request 0 from 180.40.7.130, 132 ms R2#ping 224.4.4.4sh ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:06:02/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:06:02/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:06:02/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:06:02/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:06:02/00:00:00 (180.40.7.2, 224.4.4.4), 00:02:33/00:02:55, flags: Incoming interface: Serial1/2, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:02:33/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:02:33/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:02:33/00:00:00 (180.40.7.35, 224.4.4.4), 00:02:33/00:02:55, flags: Incoming interface: Serial1/0.1, RPF nbr 0.0.0.0 Outgoing interface list: --More--   FastEthernet0/1, Forward/Sparse-Dense, 00:02:33/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:02:33/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:02:33/00:00:00 (180.40.7.65, 224.4.4.4), 00:02:33/00:02:55, flags: Incoming interface: Serial1/0.2, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:02:33/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:02:33/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:02:33/00:00:00 (*, 224.0.1.40), 00:08:52/00:02:31, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:08:09/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:08:19/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:08:47/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:08:53/00:00:00 R2#sh ip mrouteping 224.4.4.4 ? data specify data pattern df-bit enable do not fragment bit in IP header repeat specify repeat count size specify datagram size source specify source address or name timeout specify timeout interval validate validate reply data R2#ping 224.4.4.4 re ? <1-2147483647> Repeat count R2#ping 224.4.4.4 re 50 Type escape sequence to abort. Sending 50, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 32 ms Reply to request 0 from 180.40.7.130, 148 ms Reply to request 0 from 180.40.7.130, 136 ms Reply to request 0 from 180.40.7.130, 112 ms Reply to request 1 from 180.40.7.130, 36 ms Reply to request 1 from 180.40.7.130, 149 ms Reply to request 1 from 180.40.7.130, 137 ms Reply to request 1 from 180.40.7.130, 113 ms Reply to request 2 from 180.40.7.130, 36 ms Reply to request 2 from 180.40.7.130, 152 ms Reply to request 2 from 180.40.7.130, 140 ms Reply to request 2 from 180.40.7.130, 116 ms Reply to request 3 from 180.40.7.130, 36 ms Reply to request 3 from 180.40.7.130, 152 ms Reply to request 3 from 180.40.7.130, 140 ms Reply to request 3 from 180.40.7.130, 116 ms Reply to request 4 from 180.40.7.130, 36 ms Reply to request 4 from 180.40.7.130, 152 ms Reply to request 4 from 180.40.7.130, 140 ms Reply to request 4 from 180.40.7.130, 116 ms Reply to request 5 from 180.40.7.130, 37 ms Reply to request 5 from 180.40.7.130, 153 ms Reply to request 5 from 180.40.7.130, 141 ms Reply to request 5 from 180.40.7.130, 117 ms R2#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:07:56/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:07:56/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:07:56/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:07:56/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:07:56/00:00:00 (180.40.7.2, 224.4.4.4), 00:04:26/00:02:54, flags: Incoming interface: Serial1/2, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:04:26/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:04:26/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:04:26/00:00:00 (180.40.7.35, 224.4.4.4), 00:04:26/00:02:54, flags: Incoming interface: Serial1/0.1, RPF nbr 0.0.0.0 Outgoing interface list: --More--   FastEthernet0/1, Forward/Sparse-Dense, 00:04:26/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:04:27/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:04:27/00:00:00 (180.40.7.65, 224.4.4.4), 00:04:27/00:02:54, flags: Incoming interface: Serial1/0.2, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:04:27/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:04:27/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:04:27/00:00:00 (*, 224.0.1.40), 00:10:46/00:02:35, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:10:02/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:10:12/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:10:40/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:10:46/00:00:00 R2#^x4 % Unknown command or computer name, or unable to find computer address R2# R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#oin   int fa 0/0 R4(config-if)#ip ? Interface IP configuration subcommands: access-group Specify access control for packets accounting Enable IP accounting on this interface address Set the IP address of an interface audit Apply IDS audit name auth-proxy Apply authentication proxy authentication authentication subcommands bandwidth-percent Set EIGRP bandwidth limit bgp BGP interface commands broadcast-address Set the broadcast address of an interface cef Cisco Express Forwarding interface commands cgmp Enable/disable CGMP dhcp Configure DHCP parameters for this interface directed-broadcast Enable forwarding of directed broadcasts dvmrp DVMRP interface commands flow NetFlow related commands hello-interval Configures IP-EIGRP hello interval helper-address Specify a destination address for UDP broadcasts hold-time Configures IP-EIGRP hold time idle-group Specify interesting packets for idle-timer igmp IGMP interface commands information-reply Enable sending ICMP Information Reply messages --More--   R4(config-if)#ip s  ? sap security split-horizon summary-address R4(config-if)#ip s mu R4(config-if)#ip multicast ? boundary Boundary for administratively scoped multicast addresses helper-map Broadcast to Multicast map OR Multicast to ip-address map netflow NetFlow accounting for multicast rate-limit Rate limit multicast data packets tagswitch Enable IP Multicast Tagswitching ttl-threshold TTL threshold for multicast packets R4(config-if)#ip multicast           pim ? bidir-neighbor-filter PIM bidir capable peering filter bsr-border Border of PIM domain dense-mode Enable PIM dense-mode operation dr-priority PIM router DR priority nbma-mode Use Non-Broadcast Multi-Access (NBMA) mode on interface neighbor-filter PIM peering filter query-interval PIM router query interval sparse-dense-mode Enable PIM sparse-dense-mode operation sparse-mode Enable PIM sparse-mode operation state-refresh PIM DM State-Refresh configuration version PIM version R4(config-if)#ip pim st R4(config-if)#ip pim state-refresh ? origination-interval PIM State-Refresh origination interval R4(config-if)#ip pim state-refresh o R4(config-if)#ip pim state-refresh origination-interval ? <1-100> Interval in seconds R4(config-if)#ip pim state-refresh origination-interval 88 R4(config-if)#^Z R4# *Mar 1 21:04:58.510: %SYS-5-CONFIG_I: Configured from console by console R4#sh u run int fa 0/0 Building configuration... Current configuration : 209 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 88 ip pim dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4# R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *M R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#access-list 1 2en 224.20.68.1 ^ % Invalid input detected at '^' marker. R3(config)#access-list 1 2en 224.20.68.1en 224.20.68.1 den 224.20.68.1 R3(config)#access-list 1 ..per ip anyany any any .per any per any  R3(config)#ip pim rp   R3(config)#ip pim rp-a R3(config)#ip pim rp-ad R3(config)#ip pim rp-address ? A.B.C.D IP address of Rendezvous-point for group R3(config)#ip pim rp-address 180.40.7.2 129 ? <1-99> Access-list reference for group <1300-1999> Access-list reference for group (expanded range) WORD IP Named Standard Access list override Overrides dynamically learnt RP mappings R3(config)#ip pim rp-address 180.40.7.129 12  ? override Overrides dynamically learnt RP mappings R3(config)#ip pim rp-address 180.40.7.129 1 R3(config)#^Z R3#sh run | % Incomplete command. R3# *Mar 1 21:05:07.708: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b ip rp R3#sh run | b ip rpprpirpmrp rp ip pim rp-address 180.40.7.129 1 ! access-list 1 deny 224.20.68.1 access-list 1 permit any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end --More--   R3# RACK11AS>1 [Resuming connection 1 to r1 ... ] *M R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pim rp-address 180.40.7.129 1 R1(config)#! R1(config)#access-list 1 deny 224.20.68.1 R1(config)#access-list 1 permit any R1(config)# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#ip pim rp-address 180.40.7.129 1 R2(config)#! R2(config)#access-list 1 deny 224.20.68.1 R2(config)#access-list 1 permit any R2(config)# RACK11AS>4 5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#ip pim rp-address 180.40.7.129 1 S5(config)#! S5(config)#access-list 1 deny 224.20.68.1 S5(config)#access-list 1 permit any S5(config)#^Z S5# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim rp-address 180.40.7.129 1 S6(config)#! S6(config)#access-list 1 deny 224.20.68.1 S6(config)#access-list 1 permit any S6(config)# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#coi nfig t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip pim rp-address 180.40.7.129 1 R7(config)#! R7(config)#access-list 1 deny 224.20.68.1 R7(config)#access-list 1 permit any R7(config)# R7(config)#^Z R7# *Mar 1 21:06:09.161: %SYS-5-CONFIG_I: Configured from console by console R7#ship     ip pim rp Group: 224.0.1.40, RP: 180.40.7.129, uptime 00:00:26, expires never R7# R7# R7# R7#sh ip pim rp map PIM Group-to-RP Mappings Acl: 1, Static RP: 180.40.7.129 (?) R7# R7# R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 72 ms R7# R7# R7# R7# R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 64 ms R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#no ip pim rp-address 180.40.7.129 1 R7(config)#! R7(config)#no access-list 1 deny 224.20.68.1 R7(config)# R7(config)#end R7# *Mar 1 21:08:58.471: %SYS-5-CONFIG_I: Configured from console by console R7# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6(config)#config t ^ % Invalid input detected at '^' marker. S6(config)# S6(config)#no ip pim rp-address 180.40.7.129 1 S6(config)#! S6(config)#no access-list 1 deny 224.20.68.1 S6(config)# S6(config)#end S6# 21:12:16: %SYS-5-CONFIG_I: Configured from console by console RACK11AS>5 [Resuming connection 5 to r5 ... ] 21:0config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#no ip pim rp-address 180.40.7.129 1 S5(config)#! S5(config)#no access-list 1 deny 224.20.68.1 S5(config)# S5(config)#end S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config)#config t ^ % Invalid input detected at '^' marker. R2(config)# R2(config)#no ip pim rp-address 180.40.7.129 1 R2(config)#! R2(config)#no access-list 1 deny 224.20.68.1 R2(config)# R2(config)#end R2# *Mar 1 21:09:23.472: %SYS-5-CONFIG_I: Configured from console by console R2# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1(config)#config t ^ % Invalid input detected at '^' marker. R1(config)# R1(config)#no ip pim rp-address 180.40.7.129 1 R1(config)#! R1(config)#no access-list 1 deny 224.20.68.1 R1(config)# R1(config)#end R1# *Mar 1 21:10:17.933: %SYS-5-CONFIG_I: Configured from console by console R1# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pim rp-address 180.40.7.129 1 access-list 1 per any ip pim rp-address 180.40.7.129 1 nip pim rp-address 180.40.7.129 1 oip pim rp-address 180.40.7.129 1  ip pim rp-address 180.40.7.129 1  R3(config)# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim se R2(config)#ip pim send-rp-di R2(config)#ip pim send-rp-discovery ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing scope Scope of the RP discovery packets R2(config)#ip pim send-rp-discovery scop[    ? <1-255> TTL R2(config)#ip pim send-rp-discovery scop 2 R2(config)#^Z R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config)#ip pim sen R3(config)#ip pim send-rp-a R3(config)#ip pim send-rp-announce ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config)#ip pim send-rp-announce fa 0/0 ? scope RP announcement scope R3(config)#ip pim send-rp-announce fa 0/0 sc ? <1-255> TTL of the RP announce packet R3(config)#ip pim send-rp-announce fa 0/0 sc 1 ? group-list Group access-list interval RP announcement interval R3(config)#ip pim send-rp-announce fa 0/0 sc 1 grou ? <1-99> Access-list reference for multicast groups WORD IP Named Standard Access list R3(config)#ip pim send-rp-announce fa 0/0 sc 1 grou 1 ? interval RP announcement interval R3(config)#ip pim send-rp-announce fa 0/0 sc 1 grou 1 in 10 Must configure 'ip address' or 'ip unnumbered' for FastEthernet0/0 R3(config)#ip pim send-rp-announce fa 0/0 sc 1 grou 1 in 10 sc 1 grou 1 in 10 1 sc 1 grou 1 in 10 R3(config)#^Z R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Marsh ip pim rp map PIM Group-to-RP Mappings This system is an RP-mapping agent Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.129 (?), elected via Auto-RP Uptime: 00:00:11, expires: 00:00:29 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.129 (?), elected via Auto-RP Uptime: 00:00:11, expires: 00:00:29 R2# R2# R2# R2# R2# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip pim map rp ^ % Invalid input detected at '^' marker. R7#sh ip pim map rp rp  rp  rp  rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:41, expires: 00:02:15 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:41, expires: 00:02:14 R7#sh ip pim rp mapmap rp config t ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 76 ms R7# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | i ip pim send ip pim send-rp-discovery scope 2 R2#^x6 % Unknown command or computer name, or unable to find computer address R2# R2# RACK11AS> [Resuming connection 2 to r2 ... ] 6 Trying 6... % Destination unreachable; gateway or host down % Unknown command or computer name, or unable to find computer address R2# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/2 S6(config-if)#ip gi  ig S6(config-if)#ip igmp jo 224.20.68.1 S6(config-if)# RACK11AS>5 [Resuming connection 5 to r5 ... ] 21:1 S5#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 112 ms S5#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:04:14/00:02:49, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:04:14/00:00:00 S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#shj  ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:00:13/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:00:13/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:00:13/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:13/00:00:00 (17.57.100.2, 224.20.68.1), 00:00:13/00:02:54, flags: PT Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: FastEthernet0/1, Prune/Sparse-Dense, 00:00:14/00:02:45 Serial1/2, Prune/Sparse-Dense, 00:00:12/00:02:50, A (*, 224.4.4.4), 00:03:22/00:03:04, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:03:22/00:03:04 --More--   R3#q RACK11AS>6 [Resuming connection 6 to r6 ... ] S6(config-if)#^Z S6#sh 21:17:05: %SYS-5-CONFIG_I: Configured from console by console ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:00:53/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/2, Forward/Sparse-Dense, 00:00:53/00:00:00 (17.57.100.2, 224.20.68.1), 00:00:43/00:02:16, flags: PLT Incoming interface: FastEthernet0/2, RPF nbr 180.40.7.98 Outgoing interface list: Null (*, 224.0.1.39), 00:03:48/00:02:59, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/2, Forward/Sparse-Dense, 00:03:49/00:00:00 (*, 224.0.1.40), 00:04:54/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/2, Forward/Sparse-Dense, 00:04:54/00:00:00 --More--   (180.40.7.98, 224.0.1.40), 00:02:57/00:02:01, flags: PLT Incoming interface: FastEthernet0/2, RPF nbr 0.0.0.0 Outgoing interface list: Null S6#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP Uptime: 00:03:03, expires: 00:02:52 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP Uptime: 00:03:03, expires: 00:02:49 S6#sh ver Cisco IOS Software, C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(25)SED, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Sat 22-Oct-05 12:14 by yenanh Image text-base: 0x00003000, data-base: 0x00D6EDC8 ROM: Bootstrap program is C3550 boot loader S6 uptime is 21 hours, 17 minutes System returned to ROM by power-on System image file is "flash:/c3550-ipservicesk9-mz.122-25.SED.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: --More--   S6# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3 con0 is now available Press RETURN to get started. R3> R3>en R3#sh ver Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller Image text-base: 0x80008098, data-base: 0x8202B100 ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) ROM: C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) R3 uptime is 21 hours, 14 minutes System returned to ROM by power-on System image file is "flash:c2600-adventerprisek9-mz.123-16a.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you --More--   R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa0/1 R7(config-if)#ip igm jo R7(config-if)#ip igm join-group 224.7.7.7 R7(config-if)#^Z R7# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip mroute ping 224.20.68.1       7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 8 ms S5#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.7.7.7), 00:00:04/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: Null (17.57.100.2, 224.7.7.7), 00:00:04/00:02:56, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0, Registering Outgoing interface list: Null (*, 224.0.1.40), 00:06:29/00:02:29, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:06:29/00:00:00 S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh veren sh ver  sj h ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:02:35/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:02:35/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:02:35/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:02:35/00:00:00 (17.57.100.2, 224.20.68.1), 00:02:35/00:00:32, flags: PT Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: FastEthernet0/1, Prune/Sparse-Dense, 00:02:36/00:00:23 Serial1/2, Prune/Sparse-Dense, 00:02:34/00:00:28, A (*, 224.4.4.4), 00:05:44/00:02:11, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:05:44/00:02:40 --More--  (*, 224.7.7.7), 00:00:29/stopped, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:29/00:03:00 (17.57.100.2, 224.7.7.7), 00:00:20/00:02:39, flags: P Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: Null (*, 224.0.1.39), 00:05:42/00:02:15, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:05:42/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:05:42/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:05:43/00:00:00 (*, 224.0.1.40), 00:06:24/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:06:24/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:06:24/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:06:24/00:00:00 --More--   R3#x7 Translating "x7" Translating "x7" % Unknown command or computer name, or unable to find computer address R3# R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] * R7#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:02:57/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:02:57/00:00:00 (17.57.100.2, 224.20.68.1), 00:02:57/00:00:02, flags: PT Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.4.4.4), 00:04:23/00:01:41, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.7.7.7), 00:00:51/stopped, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (17.57.100.2, 224.7.7.7), 00:00:42/00:02:21, flags: PLTX --More--   Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 00:07:22/00:02:53, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:07:22/00:00:00 R7#x2 * *w  * * * * * *exit R7# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh    x2 *q ERR *e R2#sh run | i ip pim sen ip pim send-rp-discovery scope 2 R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip    ri   un | i ip pim sen ip pim send-rp-announce FastEthernet0/1 scope 1 group-list 1 interval 10 R3# R3# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#confi Configuring from terminal, memory, or network [terminal]? t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do sh access-list R1(config)#ccess       access-list 1 den 224.20.73.1 15.12e8.20.0 ^ % Invalid input detected at '^' marker. R1(config)#access-list 1 den 224.20.73.1 15.12e8.20.08.20.0  R1(config)#access-list `1    1 per any R1(config)#int e 0/0 R1(config-if)#ip ig R1(config-if)#ip igmp ? access-group IGMP group access group explicit-tracking Enable/Disable IGMP explicit-tracking helper-address IGMP helper address immediate-leave Leave groups immediately without sending last member query, use for one host network only join-group IGMP join multicast group last-member-query-count IGMP last member query count last-member-query-interval IGMP last member query interval limit IGMP limit mroute-proxy Mroute to IGMP proxy proxy-service Enable IGMP mroute proxy service querier-timeout IGMP previous querier timeout query-interval IGMP host query interval query-max-response-time IGMP max query response value static-group IGMP static multicast group unidirectional-link IGMP unidirectional link multicast routing v3lite Enable/disable IGMPv3 Lite version IGMP version R1(config-if)#ip igmp acc R1(config-if)#ip igmp access-group 1 ? R1(config-if)#ip igmp access-group 1 R1(config-if)# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/1 S5(config-if)#n o  o ip pim sp S5(config-if)#no ip pim sparse-d S5(config-if)#no ip pim sparse-dense-mode S5(config-if)#ip igm joinm     224.73.20..   273.073..73.73.1 S5(config-if)# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)#do sh access % Ambiguous command: "sh access" R1(config-if)#do sh access-li Standard IP access list 1 10 deny 224.20.73.1, wildcard bits 15.128.20.0 (1 match) 20 permit any (3 matches) R1(config-if)#do sh access-li Standard IP access list 1 10 deny 224.20.73.1, wildcard bits 15.128.20.0 (1 match) 20 permit any (3 matches) R1(config-if)#do sh access-li Standard IP access list 1 10 deny 224.20.73.1, wildcard bits 15.128.20.0 (1 match) 20 permit any (3 matches) R1(config-if)#do sh access-li Standard IP access list 1 10 deny 224.20.73.1, wildcard bits 15.128.20.0 (1 match) 20 permit any (3 matches) R1(config-if)#do sh access-li Standard IP access list 1 10 deny 224.20.73.1, wildcard bits 15.128.20.0 (1 match) 20 permit any (3 matches) R1(config-if)#^Z R1# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.20.73.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.73.1, timeout is 2 seconds: . R7# R7# R7# R7#ping 224.20.73.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.73.1, timeout is 2 seconds: . R7# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5(config-if)#ip igm joi 224.20.73.1no ip pim sparse-dense-mode no ip pim sparse-dense-mode  ip pim sparse-dense-mode  S5(config-if)#^Z S5# 21:25:43: %SYS-5-CONFIG_I: Configured from console by console S5# RACK11AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#t s % Type "show ?" for a list of subcommands R1#h access-liustsh access-liust ^ % Invalid input detected at '^' marker. R1#sh access-liustst  Standard IP access list 1 10 deny 224.20.73.1, wildcard bits 15.128.20.0 (3 matches) 20 permit any (5 matches) R1# RACK11AS>7 [Resuming connection 7 to r7 ... ] ping 224.20.73.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.73.1, timeout is 2 seconds: . R7#ping 224.20.73.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.73.1, timeout is 2 seconds: . R7#ping 224.20.73.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.73.1, timeout is 2 seconds: . R7# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:00:31/00:02:51, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:31/00:00:00 (*, 224.0.1.40), 00:00:32/00:02:47, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:32/00:00:00 S5#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:07, expires: 00:02:48 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:07, expires: 00:02:52 S5#sh ip pim rp mapmroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:00:46/00:02:55, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: Null (*, 224.0.1.40), 00:00:47/00:02:56, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:47/00:00:00 S5#q  RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.20.73.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.73.1, timeout is 2 seconds: Reply to request 0 from 17.57.100.2, 4 ms R7#^x1 % Unknown command or computer name, or unable to find computer address R7# R7# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#sh int f e 0? / R1#sh int e 0 access-listint e  0/0 Ethernet0/0 is up, line protocol is up Hardware is AmdP2, address is 0050.7358.c200 (bia 0050.7358.c200) Internet address is 17.57.100.1/24 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:01, output 00:00:02, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 9418 packets input, 1231499 bytes, 0 no buffer Received 9401 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 17367 packets output, 1716334 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier --More--   R1#sh int e0/0 rint e0/0uint e0/0nint e0/0 int e0/0 Building configuration... Current configuration : 130 bytes ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip igmp access-group 1 half-duplex end R1#sh run | i access-liust  s  st access-list 1 deny 224.20.73.1 15.128.20.0 access-list 1 permit any R1# R1#copnmf==adfpjghasdoifughniqwergoiuzdfg;oiun dfxth ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#i access-list 2 per 239.0.0.0 0.255.255.255 R1(config)#int e 0/0 R1(config-if)#ip mu R1(config-if)#ip multicast ? boundary Boundary for administratively scoped multicast addresses helper-map Broadcast to Multicast map OR Multicast to ip-address map netflow NetFlow accounting for multicast rate-limit Rate limit multicast data packets tagswitch Enable IP Multicast Tagswitching ttl-threshold TTL threshold for multicast packets R1(config-if)#ip multicast rate-limit ? in Rate limit incoming packets out Rate limit outgoing packets R1(config-if)#ip multicast rate-limit in ? <0-4294967> Rate in kilobits per second group-list Rate limit for groups source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit in grou ? <1-99> Multicast group access-list reference <1300-1999> Multicast group access-list reference (expanded range) WORD IP Named Standard Access list R1(config-if)#ip multicast rate-limit in grou 1 ? <0-4294967> Rate in kilobits per second source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit in grou 1 ? <0-4294967> Rate in kilobits per second source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit in grou 1 vi R1(config-if)#ip multicast rate-limit in grou 1 video ? <0-4294967> Rate in kilobits per second R1(config-if)#ip multicast rate-limit in grou 1 video 80 R1(config-if)#^Z R1#sh r *Mar 1 21:29:19.148: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int er 0/0 Building configuration... Current configuration : 180 bytes ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip multicast rate-limit in group-list 1 video 80 ip igmp access-group 1 half-duplex end R1# R1#cnfig t ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ip ig R1(config-if)#ip igmp q R1(config-if)#ip igmp quer? querier-timeout query-interval query-max-response-time R1(config-if)#ip igmp query R1(config-if)#ip igmp query-i R1(config-if)#ip igmp query-interval ? <1-18000> Query interval in seconds R1(config-if)#ip igmp query-interval 90 R1(config-if)#ip po im qu R1(config-if)#ip pim query-interval 90 R1(config-if)#^Z R1# *Mar 1 21:33:38.033: %SYS-5-CONFIG_I: Configured from console by console R1# R1# R1# R1#shj    ip pim int e 0/1 Address Interface Ver/ Nbr Query DR DR Mode Count Intvl Prior 17.100.1.1 Ethernet0/1 v2/SD 1 90 1 17.100.1.2 R1#sh ip pim int e 0/1 ? count Interface multicast packet count detail PIM detailed information df BIDIR PIM Designated Forwarder tag Interface specific multicast tag information | Output modifiers R1#sh ip pim int e 0/1 de Ethernet0/1 is up, line protocol is up Internet address is 17.100.1.1/24 Multicast switching: fast Multicast packets in/out: 10/27 Multicast boundary: not set Multicast TTL threshold: 0 PIM: enabled PIM version: 2, mode: sparse-dense PIM DR: 17.100.1.2 PIM neighbor count: 1 PIM Hello/Query interval: 90 seconds PIM State-Refresh processing: enabled PIM State-Refresh origination: disabled PIM NBMA mode: disabled PIM ATM multipoint signalling: disabled PIM domain border: disabled Multicast Tagswitching: disabled R1#sh ip pim int e 0/1 de                      conf g =t t ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#int e 0/1p pim query-interval 90  ? <1-65535> Query interval in seconds or milliseconds R1(config-if)#ip pim query-interval 1 ? msec Query interval in milliseconds R1(config-if)#ip pim query-interval 1                         ^Z R1#sh *Mar 1 21:35:10.829: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int e 0/1 Building configuration... Current configuration : 172 bytes ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim query-interval 90 ip pim sparse-dense-mode ip igmp query-interval 90 half-duplex no keepalive end R1# R1# RACK11AS>7 [Resuming connection 7 to r7 ... ] * R7# RACK11AS>c 4 [Resuming connection 4 to r4 ... ] R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 80 ms R4# R4# R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:44:13/00:02:44, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.7.7.7), 00:00:15/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (180.40.7.130, 224.7.7.7), 00:00:15/00:02:44, flags: PFT Incoming interface: FastEthernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.0.1.40), 00:44:23/00:02:35, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:44:23/00:00:00 R4#sh run int fa 0/0 Building configuration... Current configuration : 209 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 88 ip pim dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4#clea ip mroute * R4#clea ip mroute *sh run int fa 0/0ip mroute ping 224.7.7.7sh ip mroute run int fa 0/0clea ip mroute * sh run int fa 0/0ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:05/00:02:54, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.0.1.40), 00:00:05/00:02:54, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:00:05/00:00:00 R4#sh ip mrouteclea ip mroute *sh run int fa 0/0ip mroute ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#deb mpo   ip igm R3#deb ip igmp ? Hostname or A.B.C.D IP group address vrf Select VPN Routing/Forwarding instance R3#deb ip igmp IGMP debugging is on R3#configf    t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#log buff R3(config)#^Z R3# *Mar 1 21:37:02.115: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# *Mar 1 21:37:06.113: IGMP(0): Send v2 general Query on Serial1/0 *Mar 1 21:37:06.113: IGMP(0): Set report delay time to 9.7 seconds for 224.0.1.40 on Serial1/0 *Mar 1 21:37:07.115: IGMP(0): Send v2 general Query on FastEthernet0/1 R3# *Mar 1 21:37:08.605: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:37:08.605: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:37:08.605: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 21:37:08.609: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:37:08.609: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:37:08.613: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:37:08.613: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 R3# *Mar 1 21:37:08.613: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 R3# *Mar 1 21:37:13.890: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.4.4.4 *Mar 1 21:37:13.890: IGMP(0): Received Group record for group 224.4.4.4, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:37:13.890: IGMP(0): Updating EXCLUDE group timer for 224.4.4.4 *Mar 1 21:37:13.890: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.4.4.4) by 0 R3# *Mar 1 21:37:16.130: IGMP(0): Send v2 Report for 224.0.1.40 on Serial1/0 *Mar 1 21:37:16.130: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.33 for 224.0.1.40 *Mar 1 21:37:16.130: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.33 for 0 sources *Mar 1 21:37:16.130: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:37:16.130: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.40) by 0 *Mar 1 21:37:16.887: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.0.1.40 *Mar 1 21:37:16.891: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.130 for 0 sources R3# *Mar 1 21:37:16.891: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:37:16.891: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.0.1.40) by 0 R3# *Mar 1 21:38:06.212: IGMP(0): Send v2 general Query on Serial1/0 *Mar 1 21:38:06.212: IGMP(0): Set report delay time to 5.1 seconds for 224.0.1.40 on Serial1/0 *Mar 1 21:38:07.213: IGMP(0): Send v2 general Query on FastEthernet0/1 R3# *Mar 1 21:38:07.678: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:38:07.678: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:38:07.678: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 21:38:07.682: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:38:07.690: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:38:07.690: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:38:07.690: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 R3# *Mar 1 21:38:07.690: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 R3# *Mar 1 21:38:12.222: IGMP(0): Send v2 Report for 224.0.1.40 on Serial1/0 *Mar 1 21:38:12.222: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.33 for 224.0.1.40 *Mar 1 21:38:12.222: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.33 for 0 sources *Mar 1 21:38:12.222: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:38:12.222: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.40) by 0 R3# *Mar 1 21:38:14.886: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.0.1.40 *Mar 1 21:38:14.890: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:38:14.890: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:38:14.890: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.0.1.40) by 0 R3# *Mar 1 21:38:16.889: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.4.4.4 *Mar 1 21:38:16.889: IGMP(0): Received Group record for group 224.4.4.4, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:38:16.889: IGMP(0): Updating EXCLUDE group timer for 224.4.4.4 *Mar 1 21:38:16.889: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.4.4.4) by 0 R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:16:40/00:02:33, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:15:48/00:02:33 (*, 224.4.4.4), 00:28:39/00:03:26, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:28:39/00:03:26 (*, 224.7.7.7), 00:23:25/00:02:46, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:23:25/00:02:46 (180.40.7.130, 224.7.7.7), 00:03:37/00:01:04, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: --More--   Serial1/0, Forward/Sparse-Dense, 00:03:37/00:02:46 (*, 224.0.1.39), 00:28:39/00:02:12, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:28:39/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:28:39/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:28:39/00:00:00 (*, 224.0.1.40), 00:29:20/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:29:20/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:29:20/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:29:20/00:00:00 (180.40.7.2, 224.0.1.40), 00:27:44/00:02:04, flags: LT Incoming interface: Serial1/2, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:27:44/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:27:44/00:00:00 (180.40.7.35, 224.0.1.40), 00:27:44/00:02:04, flags: LT --More-- *Mar 1 21:39:06.310: IGMP(0): Send v2 general Query on Serial1/0 *Mar 1 21:39:06.310: IGMP(0): Set report delay time to 6.2 seconds for 224.0.1.40 on Serial1/0 *Mar 1 21:39:07.312: IGMP(0): Send v2 general Query on FastEthernet0/1 --More--   R3# *Mar 1 21:39:13.322: IGMP(0): Send v2 Report for 224.0.1.40 on Serial1/0 *Mar 1 21:39:13.322: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.33 for 224.0.1.40 *Mar 1 21:39:13.322: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.33 for 0 sources *Mar 1 21:39:13.322: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:39:13.322: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.40) by 0 R3# *Mar 1 21:39:14.808: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:39:14.808: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:39:14.808: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 21:39:14.812: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:39:14.812: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:39:14.816: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:39:14.816: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 R3# *Mar 1 21:39:14.816: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 R3# *Mar 1 21:39:15.886: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.0.1.40 *Mar 1 21:39:15.886: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:39:15.886: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:39:15.886: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.0.1.40) by 0 *Mar 1 21:39:16.888: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.4.4.4 *Mar 1 21:39:16.888: IGMP(0): Received Group record for group 224.4.4.4, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:39:16.888: IGMP(0): Updating EXCLUDE group timer for 224.4.4.4 *Mar 1 21:39:16.888: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.4.4.4) by 0 R3# RACK11AS>z 4 [Resuming connection 4 to r4 ... ] R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#x3 % Incomplete command. R4# R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh buf Buffer elements: 500 in free list (500 max allowed) 100096 hits, 0 misses, 0 created Public buffer pools: Small buffers, 104 bytes (total 50, permanent 50, peak 65 @ 21:39:17): 50 in free list (20 min, 150 max allowed) 105069 hits, 5 misses, 15 trims, 15 created 0 failures (0 no memory) Middle buffers, 600 bytes (total 25, permanent 25, peak 40 @ 21:39:17): 25 in free list (10 min, 150 max allowed) 4492 hits, 5 misses, 15 trims, 15 created 0 failures (0 no memory) Big buffers, 1536 bytes (total 50, permanent 50): 50 in free list (5 min, 150 max allowed) 4029 hits, 0 misses, 0 trims, 0 created 0 failures (0 no memory) VeryBig buffers, 4520 bytes (total 10, permanent 10): 10 in free list (0 min, 20 max allowed) 0 hits, 0 misses, 0 trims, 0 created 0 failures (0 no memory) Large buffers, 5024 bytes (total 0, permanent 0): 0 in free list (0 min, 10 max allowed) --More--   0 hits, 0 misses, 0 trims, 0 created 0 failures (0 no memory) Huge buffers, 18024 bytes (total 0, permanent 0): 0 in free list (0 min, 4 max allowed) 0 hits, 0 misses, 0 trims, 0 created 0 failures (0 no memory) Interface buffer pools: BRI0/0 buffers, 1524 bytes (total 4, permanent 4): 2 in free list (0 min, 4 max allowed) 2 hits, 0 fallbacks 2 max cache size, 1 in cache 1 hits in cache, 0 misses in cache CD2430 I/O buffers, 1536 bytes (total 40, permanent 40): 0 in free list (0 min, 40 max allowed) 40 hits, 0 fallbacks Header pools: Header buffers, 0 bytes (total 137, permanent 128, peak 137 @ 21:39:44): 9 in free list (10 min, 512 max allowed) 125 hits, 3 misses, 0 trims, 9 created 0 failures (0 no memory) 128 max cache size, 128 in cache --More--   89 hits in cache, 0 misses in cache Particle Clones: 1024 clones, 46 hits, 0 misses Public particle pools: F/S buffers, 256 bytes (total 384, permanent 384): 128 in free list (128 min, 1024 max allowed) 256 hits, 0 misses, 0 trims, 0 created 0 failures (0 no memory) 256 max cache size, 256 in cache 97 hits in cache, 0 misses in cache Normal buffers, 1548 bytes (total 512, permanent 512): 278 in free list (128 min, 1024 max allowed) 304 hits, 0 misses, 0 trims, 0 created 0 failures (0 no memory) 128 max cache size, 128 in cache 0 hits in cache, 0 misses in cache Private particle pools: FastEthernet0/0 buffers, 1548 bytes (total 192, permanent 192): 0 in free list (0 min, 192 max allowed) 192 hits, 0 fallbacks --More--   192 max cache size, 186 in cache 6 hits in cache, 0 misses in cache FastEthernet0/1 buffers, 1548 bytes (total 192, permanent 192): 0 in free list (0 min, 192 max allowed) 192 hits, 0 fallbacks 192 max cache size, 128 in cache 13896 hits in cache, 0 misses in cache BRI0/0:1 buffers, 1548 bytes (total 48, permanent 48): 0 in free list (0 min, 48 max allowed) 48 hits, 0 fallbacks 48 max cache size, 48 in cache 0 hits in cache, 0 misses in cache BRI0/0:2 buffers, 1548 bytes (total 48, permanent 48): 0 in free list (0 min, 48 max allowed) 48 hits, 0 fallbacks 48 max cache size, 48 in cache 0 hits in cache, 0 misses in cache Serial1/0 buffers, 1548 bytes (total 12, permanent 12): 0 in free list (0 min, 12 max allowed) 12 hits, 0 fallbacks 12 max cache size, 10 in cache 33381 hits in cache, 0 misses in cache Serial1/1 buffers, 1548 bytes (total 12, permanent 12): --More--   0 in free list (0 min, 12 max allowed) 12 hits, 0 fallbacks 12 max cache size, 10 in cache 6 hits in cache, 0 misses in cache Serial1/2 buffers, 1548 bytes (total 12, permanent 12): 0 in free list (0 min, 12 max allowed) 12 hits, 0 fallbacks 12 max cache size, 10 in cache 17406 hits in cache, 0 misses in cache Serial1/3 buffers, 1548 bytes (total 12, permanent 12): 0 in free list (0 min, 12 max allowed) 12 hits, 0 fallbacks 12 max cache size, 10 in cache 6 hits in cache, 0 misses in cache Serial1/4 buffers, 1548 bytes (total 12, permanent 12): 0 in free list (0 min, 12 max allowed) 12 hits, 0 fallbacks 12 max cache size, 10 in cache 6 hits in cache, 0 misses in cache Serial1/5 buffers, 1548 bytes (total 12, permanent 12): 0 in free list (0 min, 12 max allowed) 12 hits, 0 fallbacks 12 max cache size, 10 in cache --More--   6 hits in cache, 0 misses in cache Serial1/6 buffers, 1548 bytes (total 12, permanent 12): 0 in free list (0 min, 12 max allowed) 12 hits, 0 fallbacks 12 max cache size, 10 in cache 6 hits in cache, 0 misses in cache Serial1/7 buffers, 1548 bytes (total 12, permanent 12): 0 in free list (0 min, 12 max allowed) 12 hits, 0 fallbacks 12 max cache size, 10 in cache 6 hits in cache, 0 misses in cache R3#                                        sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 130 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 73 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 64 message lines logged --More--   Log Buffer (4096 bytes): v2 general Query on FastEthernet0/1 *Mar 1 21:38:07.678: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:38:07.678: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:38:07.678: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 21:38:07.682: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:38:07.690: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:38:07.690: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:38:07.690: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 21:38:07.690: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:38:12.222: IGMP(0): Send v2 Report for 224.0.1.40 on Serial1/0 *Mar 1 21:38:12.222: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.33 for 224.0.1.40 *Mar 1 21:38:12.222: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.33 for 0 sources *Mar 1 21:38:12.222: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:38:12.222: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.40) by 0 *Mar 1 21:38:14.886: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.0.1.40 --More--  *Mar 1 21:38:14.890: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:38:14.890: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:38:14.890: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.0.1.40) by 0 *Mar 1 21:38:16.889: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.4.4.4 *Mar 1 21:38:16.889: IGMP(0): Received Group record for group 224.4.4.4, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:38:16.889: IGMP(0): Updating EXCLUDE group timer for 224.4.4.4 *Mar 1 21:38:16.889: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.4.4.4) by 0 *Mar 1 21:39:06.310: IGMP(0): Send v2 general Query on Serial1/0 *Mar 1 21:39:06.310: IGMP(0): Set report delay time to 6.2 seconds for 224.0.1.40 on Serial1/0 *Mar 1 21:39:07.312: IGMP(0): Send v2 general Query on FastEthernet0/1 *Mar 1 21:39:13.322: IGMP(0): Send v2 Report for 224.0.1.40 on Serial1/0 *Mar 1 21:39:13.322: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.33 for 224.0.1.40 *Mar 1 21:39:13.322: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.33 for 0 sources *Mar 1 21:39:13.322: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:39:13.322: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.40) by 0 --More--  *Mar 1 21:39:14.808: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:39:14.808: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:39:14.808: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 21:39:14.812: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:39:14.812: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:39:14.816: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:39:14.816: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 21:39:14.816: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:39:15.886: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.0.1.40 *Mar 1 21:39:15.886: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:39:15.886: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:39:15.886: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.0.1.40) by 0 *Mar 1 21:39:16.888: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.4.4.4 *Mar 1 21:39:16.888: IGMP(0): Received Group record for group 224.4.4.4, mode 2 from 180.40.7.130 for 0 sources --More--  *Mar 1 21:39:16.888: IGMP(0): Updating EXCLUDE group timer for 224.4.4.4 *Mar 1 21:39:16.888: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.4.4.4) by 0 R3# *Mar 1 21:40:06.485: IGMP(0): Send v2 general Query on Serial1/0 *Mar 1 21:40:06.485: IGMP(0): Set report delay time to 3.8 seconds for 224.0.1.40 on Serial1/0 *Mar 1 21:40:07.487: IGMP(0): Send v2 general Query on FastEthernet0/1 R3# *Mar 1 21:40:10.491: IGMP(0): Send v2 Report for 224.0.1.40 on Serial1/0 *Mar 1 21:40:10.491: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.33 for 224.0.1.40 *Mar 1 21:40:10.491: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.33 for 0 sources *Mar 1 21:40:10.491: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:40:10.491: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.40) by 0 *Mar 1 21:40:10.884: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.4.4.4 *Mar 1 21:40:10.884: IGMP(0): Received Group record for group 224.4.4.4, mode 2 from 180.40.7.130 for 0 sources R3# *Mar 1 21:40:10.888: IGMP(0): Updating EXCLUDE group timer for 224.4.4.4 *Mar 1 21:40:10.888: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.4.4.4) by 0 *Mar 1 21:40:10.888: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.0.1.40 *Mar 1 21:40:10.888: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:40:10.888: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:40:10.888: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.0.1.40) by 0 R3# *Mar 1 21:40:15.968: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:40:15.968: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:40:15.968: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 21:40:15.968: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:40:15.972: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:40:15.972: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:40:15.976: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 R3# *Mar 1 21:40:15.976: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 R3# clea log Clear logging buffer [confirm] R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#int fa 0/1p igm join-group 224.7.7.7nip igm join-group 224.7.7.7oip igm join-group 224.7.7.7 ip igm join-group 224.7.7.7 R7(config-if)#no ip igm join-group 224.7.7.7int fa 0/1 no ip igm join-group 224.7.7.7no ip igm join-group 224.7.7.7  ip igm join-group 224.7.7.7  R7(config-if)#^Z R7#3 Trying 3... % Destination unreachable; gateway or host down % Unknown command or computer name, or unable to find computer address R7# R7# *Mar 1 21:40:32.383: %SYS-5-CONFIG_I: Configured from console by console R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 154 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 97 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 64 message lines logged --More--   Log Buffer (4096 bytes): R3# sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 154 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 97 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 64 message lines logged --More--   Log Buffer (4096 bytes): R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#clea ip          RACK11AS>3 4 [Resuming connection 4 to r4 ... ] R4#x3ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *M R3#ping 244.6 7.7.7. *Mar 1 21:42:14.166: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:42:14.166: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:42:14.166: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 21:42:14.166: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:42:14.170: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.35 for 224.0.1.39 *Mar 1 21:42:14.170: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.35 for 0 sources *Mar 1 21:42:14.174: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 R3#ping 244.7.7.7. *Mar 1 21:42:14.174: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.39) by 0 *Mar 1 21:42:14.883: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.0.1.40 *Mar 1 21:42:14.883: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.130 for 0 sources *Mar 1 21:42:14.883: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:42:14.883: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.0.1.40) by 0 R3#ping 244.7.7.7. *Mar 1 21:42:16.738: IGMP(0): Send v2 Report for 224.0.1.40 on Serial1/0 *Mar 1 21:42:16.738: IGMP(0): Received v2 Report on Serial1/0 from 180.40.7.33 for 224.0.1.40 *Mar 1 21:42:16.738: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 180.40.7.33 for 0 sources *Mar 1 21:42:16.738: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 21:42:16.738: IGMP(0): MRT Add/Update Serial1/0 for (*,224.0.1.40) by 0 *Mar 1 21:42:16.883: IGMP(0): Received v2 Report on FastEthernet0/1 from 180.40.7.130 for 224.4.4.4 *Mar 1 21:42:16.883: IGMP(0): Received Group record for group 224.4.4.4, mode 2 from 180.40.7.130 for 0 sources R3#ping 244.7.7.7. *Mar 1 21:42:16.883: IGMP(0): Updating EXCLUDE group timer for 224.4.4.4 *Mar 1 21:42:16.883: IGMP(0): MRT Add/Update FastEthernet0/1 for (*,224.4.4.4) by 0 R3#ping 244.7.7.7..7.7.7. 24.7.7.7.4.7.7.7.  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 80 ms Reply to request 0 from 17.100.1.2, 144 ms Reply to request 0 from 17.100.1.2, 132 ms R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#u all All possible debugging has been turned off R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/1 R3(config-if)#p pim ? % Ambiguous command: "p pim " R3(config-if)#p pim       ip pim ? bidir-neighbor-filter PIM bidir capable peering filter bsr-border Border of PIM domain dense-mode Enable PIM dense-mode operation dr-priority PIM router DR priority nbma-mode Use Non-Broadcast Multi-Access (NBMA) mode on interface neighbor-filter PIM peering filter query-interval PIM router query interval sparse-dense-mode Enable PIM sparse-dense-mode operation sparse-mode Enable PIM sparse-mode operation state-refresh PIM DM State-Refresh configuration version PIM version R3(config-if)#ip pim de R3(config-if)#ip pim dense-mode ? proxy-register Send proxy registers R3(config-if)#ip pim dense-mode pro R3(config-if)#ip pim dense-mode proxy-register ? list Access list route-map Route-map R3(config-if)#ip pim dense-mode proxy-register                                  exit R3(config)#int fa 0/1 R3(config-if)#ip pim de R3(config-if)#ip pim dense-mode p R3(config-if)#ip pim dense-mode proxy-register 1 ? % Unrecognized command R3(config-if)#ip pim dense-mode proxy-register 1   ? % Unrecognized command R3(config-if)#ip pim dense-mode proxy-register 1   ? list Access list route-map Route-map R3(config-if)#ip pim dense-mode proxy-register list ? <100-199> Extended access list number <2000-2699> Extended access list number (expanded range) WORD IP named extended access list R3(config-if)#ip pim dense-mode proxy-register list 1 ? R3(config-if)#ip pim dense-mode proxy-register list 1                                         access R3(config-if)#access-expression -list ist                         exit R3(config)#access-list             do sh access-list Standard IP access list 1 10 deny 224.20.68.1 20 permit any (91 matches) R3(config)#access-list 100 per ip any any R3(config)#int fa 0/1 R3(config-if)#ip pim de pro list 100 ? R3(config-if)#ip pim de pro list 100 Warning: PIM register rate-limit set to 2 messages per second R3(config-if)#^Z R3# *Mar 1 21:45:57.761: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:24:00/00:03:03, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:23:09/00:03:03 (*, 224.4.4.4), 00:36:00/00:02:59, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:36:00/00:00:00 (*, 224.7.7.7), 00:30:46/00:03:14, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:30:46/00:03:14 (180.40.7.130, 224.7.7.7), 00:10:58/00:03:24, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: --More--   Serial1/0, Forward/Sparse-Dense, 00:10:58/00:03:14 --More--   --More--  (*, 224.0.1.39), 00:36:05/00:02:47, RP 0.0.0.0, flags: DC --More--   Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:36:13/00:00:00 FastEthernet0/1, Forward/Dense, 00:36:13/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:36:13/00:00:00 (*, 224.0.1.40), 00:36:54/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:36:54/00:00:00 FastEthernet0/1, Forward/Dense, 00:36:54/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:36:54/00:00:00 (180.40.7.2, 224.0.1.40), 00:35:19/00:02:30, flags: LT Incoming interface: Serial1/2, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:35:19/00:00:00 FastEthernet0/1, Forward/Dense, 00:35:19/00:00:00 (180.40.7.35, 224.0.1.40), 00:35:19/00:02:30, flags: LT Incoming interface: Serial1/0, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:35:19/00:00:00 --More--   Serial1/2, Forward/Sparse-Dense, 00:35:20/00:00:00 R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:24:32/00:02:32, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:23:40/00:02:32 (*, 224.4.4.4), 00:36:31/00:03:26, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:36:31/00:00:00 (*, 224.7.7.7), 00:31:17/00:02:43, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:31:17/00:02:43 (180.40.7.130, 224.7.7.7), 00:11:29/00:03:23, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: --More--   Serial1/0, Forward/Sparse-Dense, 00:11:29/00:02:43 --More--   --More--  (*, 224.0.1.39), 00:36:35/00:02:17, RP 0.0.0.0, flags: DC --More--   Incoming interface: Null, RPF nbr 0.0.0.0 --More--   Outgoing interface list: --More-- RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#shj ip       h ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:24:52/00:03:07, RP 180.40.7.129, flags: S Incoming interface: Serial0/0.1, RPF nbr 180.40.7.33 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:24:00/00:03:07 (*, 224.7.7.7), 00:31:36/00:03:35, RP 180.40.7.129, flags: SJCF Incoming interface: Serial0/0.1, RPF nbr 180.40.7.33 Outgoing interface list: Ethernet0/1, Forward/Sparse-Dense, 00:31:37/00:03:16 (*, 224.0.1.39), 00:36:50/00:02:02, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:36:50/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 00:36:50/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 00:36:50/00:00:00 Ethernet0/0, Forward/Sparse-Dense, 00:36:50/00:00:00 --More--  (*, 224.0.1.40), 00:37:45/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:37:45/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 00:37:45/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 00:37:45/00:00:00 Ethernet0/0, Forward/Sparse-Dense, 00:37:45/00:00:00 (180.40.7.65, 224.0.1.40), 00:35:58/00:02:52, flags: LT Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:35:58/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 00:35:58/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 00:35:58/00:00:00 R1# RACK11AS>3 [Resuming connection 3 to r3 ... ]   Serial1/2, Forward/Sparse-Dense, 00:36:36/00:00:00 --More--   R3#sh ip mrouteconfig t u all config tsh ip mroute sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:25:12/00:02:51, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:24:20/00:02:51 (*, 224.4.4.4), 00:37:11/00:02:48, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:37:11/00:00:00 (*, 224.7.7.7), 00:31:57/00:03:02, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:31:57/00:03:02 (180.40.7.130, 224.7.7.7), 00:12:09/00:02:43, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: --More--   Serial1/0, Forward/Sparse-Dense, 00:12:09/00:03:02 --More--   --More--  (*, 224.0.1.39), 00:37:14/00:02:43, RP 0.0.0.0, flags: DC --More--   R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int fa 0/1 Building configuration... Current configuration : 151 bytes ! interface FastEthernet0/1 ip address 17.100.1.2 255.255.255.0 ip pim sparse-dense-mode ip igmp join-group 224.7.7.7 duplex auto speed auto end R7#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.7.7.7), 00:32:58/00:02:09, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 00:39:27/00:02:10, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:39:27/00:00:00 R7#clea ip mroute * R7#clea ip mroute *sh ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.7.7.7), 00:00:03/00:02:56, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 00:00:03/00:02:56, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:03/00:00:00 R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:26:34/00:03:28, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:25:42/00:03:28 (*, 224.4.4.4), 00:38:33/00:03:21, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:38:33/00:00:00 (*, 224.7.7.7), 00:33:19/00:02:39, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:33:19/00:02:39 (180.40.7.130, 224.7.7.7), 00:13:31/00:02:51, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: --More--   Serial1/0, Forward/Sparse-Dense, 00:13:31/00:02:39 (*, 224.0.1.39), 00:38:38/00:02:20, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:38:38/00:00:00 FastEthernet0/1, Forward/Dense, 00:38:38/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:38:38/00:00:00 (*, 224.0.1.40), 00:39:19/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:39:19/00:00:00 FastEthernet0/1, Forward/Dense, 00:39:19/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:39:19/00:00:00 (180.40.7.2, 224.0.1.40), 00:37:43/00:02:56, flags: LT Incoming interface: Serial1/2, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:37:43/00:00:00 FastEthernet0/1, Forward/Dense, 00:37:43/00:00:00 (180.40.7.35, 224.0.1.40), 00:37:43/00:02:56, flags: LT --More--   R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim send-rp-discovery scop 2end ip pim send-rp-discovery scop 2nip pim send-rp-discovery scop 2oip pim send-rp-discovery scop 2 ip pim send-rp-discovery scop 2 R2(config)#ip pim bs R2(config)#ip pim bsr-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config)#ip pim bsr-candidate fa 0/1 ? <0-32> Hash Mask length for RP selection R2(config)#ip pim bsr-candidate fa 0/1 R2(config)# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int     ip pim de pro list 100 nt fa 0/1 access-list 100 per ip any anydo sh access-list exit int fa 0/1exit int fa 0/1log buff int fa 0/1exit int fa 0/1exit do sh access-listaccess-list 100 per ip any anyint fa 0/1 p pim de pro list 100  do sh run | i ip pim sen ip pim send-rp-announce FastEthernet0/1 scope 1 group-list 1 interval 10 R3(config)#no ip pim send-rp-announce FastEthernet0/1 scope 1 group-list 1 in$end-rp-announce FastEthernet0/1 scope 1 group-list 1 int erval 10 R3(config)#ip pim rp R3(config)#ip pim rp-c R3(config)#ip pim rp-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config)#ip pim rp-candidate fa 0/1 ? group-list group-list interval RP candidate advertisement interval priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 grou 1 ? interval RP candidate advertisement interval priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 grou 1 p   int 10 R3(config)#^Z R3# *Mar 1 21:50:39.943: %PIM-6-INVALID_RP_JOIN: Received (*, 224.20.68.1) Join from 0.0.0.0 for invalid RP 180.40.7.129 R3# *Mar 1 21:50:40.729: %SYS-5-CONFIG_I: Configured from console RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config)#^Z R2#sh ip *Mar 1 21:50:47.904: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip pim rp map PIM Group-to-RP Mappings This system is the Bootstrap Router (v2) Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.3 (?), via bootstrap, priority 0, holdtime 35 Uptime: 00:00:08, expires: 00:00:26 R2# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#sh in t    run int fa 0/1 2 Building configuration... Current configuration : 146 bytes ! interface FastEthernet0/2 no switchport ip address 180.40.7.97 255.255.255.224 ip pim sparse-dense-mode ip igmp join-group 224.20.68.1 end S6# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP, via bootstrap, priority 0 Uptime: 00:28:25, expires: 00:00:16 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:28:25, expires: 00:00:16 S5#clea ip pim rp map   * ^ % Invalid input detected at '^' marker. S5#clea ip pim rp *  S5#clea ip pim rp *sh ip pim rp map PIM Group-to-RP Mappings S5# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip pim rp map PIM Group-to-RP Mappings R1#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:03, expires: 00:03:21 R1# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0 Uptime: 00:00:08, expires: 00:03:17 S5#sh ip pim rp mapclea ip pim rp *sh ip pim rp mapping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 88 ms S5#ping 224.4.4.420.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:00:56/00:02:48, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: Null (*, 224.4.4.4), 00:00:14/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: Null (17.57.100.2, 224.4.4.4), 00:00:14/00:02:47, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0, Registering Outgoing interface list: Null (*, 224.20.68.1), 00:00:28/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: Null (17.57.100.2, 224.20.68.1), 00:00:28/00:02:49, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 --More--   Outgoing interface list: Null (*, 224.0.1.40), 00:30:08/00:02:38, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:30:08/00:00:00 S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] ole R3# R3#confi gt ^ % Invalid input detected at '^' marker. R3#i configt Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R3#inconfigt    t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ip pim ? bidir-neighbor-filter PIM bidir capable peering filter bsr-border Border of PIM domain dense-mode Enable PIM dense-mode operation dr-priority PIM router DR priority nbma-mode Use Non-Broadcast Multi-Access (NBMA) mode on interface neighbor-filter PIM peering filter query-interval PIM router query interval sparse-dense-mode Enable PIM sparse-dense-mode operation sparse-mode Enable PIM sparse-mode operation state-refresh PIM DM State-Refresh configuration version PIM version R3(config-if)#ip pim dr R3(config-if)#ip pim dr-priority ? <0-4294967294> DR priority, preference given to larger value R3(config-if)#ip pim dr-priority 4294967294 R3(config-if)#\  *Mar 1 21:53:19.962: %PIM-5-DRCHG: DR change from neighbor 180.40.7.35 to 180.40.7.33 on interface Serial1/0 (vrf default) R3(config-if)#^Z R3# *Mar 1 21:53:21.733: %SYS-5-CONFIG_I: Configured from console by console R3# R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 80 ms R4# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip mrouteping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip mroutee \ ^ % Invalid input detected at '^' marker. S6#sh ip mroute\  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:02:21/00:02:47, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/2, RPF nbr 180.40.7.98 Outgoing interface list: Null (*, 224.0.1.40), 00:44:59/00:02:46, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/2, Forward/Sparse-Dense, 00:44:59/00:00:00 S6#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0 Uptime: 00:02:21, expires: 00:03:07 S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ipp    igp  S6(config)#ip igmp jo S6(config)#ip igmp jo224.6.6.6 ^ % Invalid input detected at '^' marker. S6(config)#ip igmp jo224.6.6.6o 224.6.6.6 ^ % Invalid input detected at '^' marker. S6(config)#ip igmp jo 224.6.6.6 int fa 0/2 S6(config-if)#int fa 0/2p igmp jo 224.6.6.6 S6(config-if)#^Z S6# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#ping 224.6.6.6.  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 112 ms S5#ping 224.6.6.620.68.16.6.6   RACK11AS>6 [Resuming connection 6 to r6 ... ] 21:5 S6#sh run int fa 0/2 Building configuration... Current configuration : 176 bytes ! interface FastEthernet0/2 no switchport ip address 180.40.7.97 255.255.255.224 ip pim sparse-dense-mode ip igmp join-group 224.20.68.1 ip igmp join-group 224.6.6.6 end S6# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#ping 224.6.6.620.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:03:54/00:02:45, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: Null (*, 224.6.6.6), 00:00:48/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: Null (17.57.100.2, 224.6.6.6), 00:00:48/00:02:18, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0, Registering Outgoing interface list: Null (*, 224.4.4.4), 00:03:13/00:02:48, RP 180.40.7.129, flags: SP Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: Null (*, 224.20.68.1), 00:03:26/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 --More--   Outgoing interface list: Null (17.57.100.2, 224.20.68.1), 00:03:27/00:02:29, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0, Registering Outgoing interface list: Null (*, 224.0.1.40), 00:33:04/00:02:40, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:33:05/00:00:00 S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:03:48/00:02:39, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:03:48/00:02:39 FastEthernet0/1, Forward/Dense, 00:03:48/00:00:00 (*, 224.20.68.1), 00:04:24/00:03:21, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:03:06/00:03:20 FastEthernet0/1, Forward/Dense, 00:04:25/00:00:00 (17.57.100.2, 224.20.68.1), 00:03:36/00:02:26, flags: T Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:03:36/00:00:00 (*, 224.4.4.4), 00:03:55/00:02:37, RP 180.40.7.129, flags: SJC --More--   Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:04:01/00:00:00 (*, 224.6.6.6), 00:01:11/00:03:17, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:01:11/00:03:17 FastEthernet0/1, Forward/Dense, 00:01:11/00:00:00 (17.57.100.2, 224.6.6.6), 00:01:05/00:01:54, flags: Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:01:05/00:00:00 (*, 224.7.7.7), 00:03:55/00:03:29, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:03:55/00:03:29 FastEthernet0/1, Forward/Dense, 00:03:55/00:00:00 (180.40.7.130, 224.7.7.7), 00:02:21/00:01:09, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 --More--   R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#sh  \   sh run int fa 0/2 Building configuration... Current configuration : 176 bytes ! interface FastEthernet0/2 no switchport ip address 180.40.7.97 255.255.255.224 ip pim sparse-dense-mode ip igmp join-group 224.20.68.1 ip igmp join-group 224.6.6.6 end S6# S6# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip mrouteping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 108 ms R7# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#1 % Unknown command or computer name, or unable to find computer address S5# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#sh    pin 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 100 ms Reply to request 0 from 180.40.7.97, 156 ms Reply to request 0 from 180.40.7.97, 144 ms R1#^Z R1# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#1ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#ping 224.20.68.11 ping 224.20.68.1sh ip mroute ping 224.20.68.16.6.6  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: . S5#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: . S5#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: . S5#a ip      clea ip mroute * S5#clea ip mroute * S5#clea ip mroute * S5#clea ip mroute * S5#clea ip mroute * S5#clea ip mroute *ping 224.6.6.6 20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#ping 224.20.68.1clea ip mroute *ping 224.6.6.6  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: . S5#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.57.100.0 is directly connected, FastEthernet0/1 O 17.100.1.0 [110/20] via 17.57.100.1, 01:11:54, FastEthernet0/1 O 192.10.32.0/24 [110/76] via 17.57.100.1, 01:11:54, FastEthernet0/1 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.128/27 [110/75] via 17.57.100.1, 01:11:54, FastEthernet0/1 O 180.40.7.0/27 [110/855] via 17.57.100.1, 01:11:54, FastEthernet0/1 O 180.40.7.33/32 [110/74] via 17.57.100.1, 01:11:54, FastEthernet0/1 O 180.40.7.32/27 [110/74] via 17.57.100.1, 01:11:55, FastEthernet0/1 O 180.40.7.66/32 [110/10] via 17.57.100.1, 01:11:55, FastEthernet0/1 O 180.40.7.65/32 [110/74] via 17.57.100.1, 01:11:55, FastEthernet0/1 O 180.40.7.96/27 [110/75] via 17.57.100.1, 01:11:55, FastEthernet0/1 S5#^x   RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/791] via 180.40.7.66, 01:12:10, Serial1/0.2 O 17.100.1.0 [110/791] via 180.40.7.66, 01:12:10, Serial1/0.2 O 192.10.32.0/24 [110/783] via 180.40.7.3, 01:12:10, Serial1/2 [110/783] via 180.40.7.33, 01:12:10, Serial1/0.1 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.128/27 [110/782] via 180.40.7.3, 01:12:10, Serial1/2 [110/782] via 180.40.7.33, 01:12:10, Serial1/0.1 C 180.40.7.0/27 is directly connected, Serial1/2 O 180.40.7.33/32 [110/781] via 180.40.7.3, 01:12:12, Serial1/2 [110/781] via 180.40.7.33, 01:12:12, Serial1/0.1 C 180.40.7.32/27 is directly connected, Serial1/0.1 O 180.40.7.66/32 [110/781] via 180.40.7.66, 01:12:12, Serial1/0.2 --More--   R2#sh ip mou  route IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:46:15/stopped, RP 180.40.7.129, flags: SJC Incoming interface: Serial1/0.1, RPF nbr 180.40.7.33 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:46:15/00:02:29 (17.57.100.1, 224.20.68.1), 00:01:27/00:01:32, flags: J Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:27/00:02:29 (17.100.1.1, 224.20.68.1), 00:01:28/00:01:31, flags: J Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:28/00:02:28 (17.100.1.2, 224.20.68.1), 00:02:04/00:00:56, flags: J Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: --More--   FastEthernet0/1, Forward/Sparse-Dense, 00:02:04/00:02:28 (180.40.7.66, 224.20.68.1), 00:01:34/00:01:33, flags: JT Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:34/00:02:22 (*, 224.6.6.6), 00:04:54/00:02:23, RP 180.40.7.129, flags: SJC Incoming interface: Serial1/0.1, RPF nbr 180.40.7.33 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:04:54/00:02:23 (*, 224.0.1.40), 00:50:13/00:02:38, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:50:13/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:50:13/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:50:13/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:50:13/00:00:00 R2#  sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:46:31/stopped, RP 180.40.7.129, flags: SJC Incoming interface: Serial1/0.1, RPF nbr 180.40.7.33 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:46:31/00:02:14 (17.57.100.1, 224.20.68.1), 00:01:42/00:01:17, flags: J Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:42/00:02:14 (17.100.1.1, 224.20.68.1), 00:01:44/00:01:16, flags: J Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:44/00:02:13 (17.100.1.2, 224.20.68.1), 00:02:19/00:00:40, flags: J Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: --More--   FastEthernet0/1, Forward/Sparse-Dense, 00:02:19/00:02:13 (180.40.7.66, 224.20.68.1), 00:01:45/00:01:23, flags: JT Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:45/00:02:11 (*, 224.6.6.6), 00:05:05/00:02:12, RP 180.40.7.129, flags: SJC Incoming interface: Serial1/0.1, RPF nbr 180.40.7.33 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:05:05/00:02:12 (*, 224.0.1.40), 00:50:23/00:02:28, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:50:23/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:50:23/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:50:23/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:50:23/00:00:00 R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:08:24/00:02:57, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:08:24/00:02:57 FastEthernet0/1, Forward/Dense, 00:08:24/00:00:00 (*, 224.20.68.1), 00:09:00/00:02:41, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:07:42/00:02:40 FastEthernet0/1, Forward/Dense, 00:09:01/00:00:00 (17.57.100.1, 224.20.68.1), 00:02:21/00:00:38, flags: Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:02:21/00:00:00 (17.57.100.2, 224.20.68.1), 00:08:12/00:01:20, flags: T --More--   Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:08:14/00:00:00 (17.100.1.1, 224.20.68.1), 00:02:23/00:00:36, flags: Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:02:23/00:00:00 (17.100.1.2, 224.20.68.1), 00:02:59/00:00:01, flags: Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:02:59/00:00:00 (180.40.7.34, 224.20.68.1), 00:02:23/00:00:38, flags: T Incoming interface: Serial1/0, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:02:23/00:00:00 (*, 224.4.4.4), 00:08:33/00:02:54, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:08:33/00:00:00 --More--   (*, 224.6.6.6), 00:06:02/00:03:23, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:06:02/00:03:23 FastEthernet0/1, Forward/Dense, 00:06:02/00:00:00 (17.57.100.2, 224.6.6.6), 00:02:22/00:01:09, flags: T Incoming interface: Serial1/0, RPF nbr 180.40.7.34 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:02:22/00:00:00 (*, 224.7.7.7), 00:08:46/00:02:36, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:08:46/00:02:36 FastEthernet0/1, Forward/Dense, 00:08:46/00:00:00 (*, 224.0.1.40), 00:51:06/00:02:30, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:51:06/00:00:00 FastEthernet0/1, Forward/Dense, 00:51:06/00:00:00 --More--   R3#clea ip mroute 8 * R3# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip routeping 224.6.6.620.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . S5#ping 224.20.68.1sh ip route ping 224.6.6.6aa Translating "224.6.6.6aa" % Unrecognized host or address, or protocol not running. S5#ping 224.6.6.6aa   Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: . S5#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: . S5# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#pin 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 133 ms R1#pin 224.20.68.1       6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 124 ms R1# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . R7#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: . R7# RACK11AS>2 1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#shut R1(config-subif)#^Z R1# *Mar 1 22:02:35.377: %PIM-5-NBRCHG: neighbor 180.40.7.33 DOWN on interface Serial0/0.1 (vrf default) non DR *Mar 1 22:02:35.381: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial0/0.1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 22:02:35.849: %SYS-5-CONFIG_I: Configured from console by console R1# RACK11AS> [Resuming connection 1 to r1 ... ] R1#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:10:01/00:03:05, RP 180.40.7.129, flags: S Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:10:01/00:03:05 (*, 224.20.68.1), 00:10:37/stopped, RP 180.40.7.129, flags: SPF Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null (17.57.100.1, 224.20.68.1), 00:03:58/00:02:45, flags: T Incoming interface: Ethernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:03:58/00:03:23 (17.57.100.2, 224.20.68.1), 00:09:49/00:02:34, flags: T Incoming interface: Ethernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:00:08/00:03:21 --More--   (17.100.1.1, 224.20.68.1), 00:04:00/00:02:42, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:04:00/00:03:18 (17.100.1.2, 224.20.68.1), 00:00:33/00:03:01, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:00:11/00:03:18 (180.40.7.66, 224.20.68.1), 00:03:27/00:02:13, flags: PFT Incoming interface: Serial0/0.2, RPF nbr 0.0.0.0, Registering Outgoing interface list: Null (*, 224.6.6.6), 00:07:14/stopped, RP 180.40.7.129, flags: SPF Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null (17.57.100.1, 224.6.6.6), 00:00:38/00:02:51, flags: T Incoming interface: Ethernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:00:10/00:03:19 --More--   R1#sh ip mrouteconfig t pin 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 116 ms Reply to request 0 from 180.40.7.97, 160 ms Reply to request 0 from 180.40.7.97, 144 ms R1# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 85 ms R7# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5# S5#ping 224.6.6.6aa  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 84 ms S5#ping 224.6.6.6aa20.68.1sh ip route ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 88 ms S5# RACK11AS>7 4 [Resuming connection 4 to r4 ... ] R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 124 ms R4#^xz    RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b            sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:03:47/00:02:40, RP 180.40.7.129, flags: S Incoming interface: Serial1/0.1, RPF nbr 180.40.7.33 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:03:47/00:02:40 (*, 224.20.68.1), 00:52:24/stopped, RP 180.40.7.129, flags: SJC Incoming interface: Serial1/0.1, RPF nbr 180.40.7.33 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:52:26/00:02:23 (17.57.100.2, 224.20.68.1), 00:03:48/00:00:14, flags: T Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: Serial1/0.1, Forward/Sparse-Dense, 00:03:48/00:02:47 FastEthernet0/1, Forward/Sparse-Dense, 00:03:48/00:02:23 (17.100.1.2, 224.20.68.1), 00:03:48/00:00:04, flags: T Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 --More--   R2#sh run | i ip pim bsr ip pim bsr-candidate FastEthernet0/1 0 R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run | int    ip pim rp-ca ip pim rp-candidate FastEthernet0/1 group-list 1 interval 10 R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip ? Global IP configuration subcommands: access-list Named access-list accounting-list Select hosts for which IP accounting information is kept accounting-threshold Sets the maximum number of accounting entries accounting-transits Sets the maximum number of transit entries address-pool Specify default IP address pooling mechanism alias Alias an IP address to a TCP port as-path BGP autonomous system path filter audit Intrusion Detection System auth-proxy Authentication Proxy bgp-community format for BGP community bootp Config BOOTP services cef Cisco Express Forwarding classless Follow classless routing forwarding rules community-list Add a community list entry default-gateway Specify default gateway (if not routing IP) default-network Flags networks as candidates for default routes dhcp Configure DHCP server and relay parameters dhcp-client Configure parameters for DHCP client operation dhcp-server Specify address of DHCP server to use director Distributed director configuration commands --More--   R3(config)#ip poi  im ? accept-register Registers accept filter accept-rp RP accept filter autorp Configure AutoRP global operations bidir-enable Enable Bidir-PIM bsr-candidate Candidate bootstrap router (candidate BSR) log-neighbor-changes Log PIM neighbor up/down and DR changes register-rate-limit Rate limit for PIM data registers register-source Source address for PIM Register rp-address PIM RP-address (Rendezvous Point) rp-announce-filter Auto-RP announce message filter rp-candidate To be a PIMv2 RP candidate send-rp-announce Auto-RP send RP announcement send-rp-discovery Auto-RP send RP discovery message (as RP-mapping agent) spt-threshold Source-tree switching threshold ssm Configure Source Specific Multicast state-refresh PIM DM State-Refresh configuration vrf Select VPN Routing/Forwarding instance R3(config)#ip pim > sp R3(config)#ip pim spt-threshold ? <0-4294967> Traffic rate in kilobits per second infinity Never switch to source-tree R3(config)#ip pim spt-threshold 1 R3(config)#^Z R3# *Mar 1 22:07:18.685: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#confi gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pim spt-threshold 1 R1(config)#^Z R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim spt-threshold 1 R2(config)# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#conf     RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip pim spt-threshold 1^Z R4# *Mar 1 22:10:20.834: %SYS-5-CONFIG_I: Configured from console by console R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip pim spt-threshold 1 R4(config)# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip pim spt-threshold 1 S5(config)#^Z S5# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim spt-threshold 1 S6(config)#^Z S6# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#ip pim spt-threshold 1 R7(config)#^Z R7# *Mar 1 22:08:17.004: %SYS-5-CONFIG_I: Configured from console by console R7# RACK11AS>1 [Resuming connection 1 to r1 ... ] *M R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#no shut R1(config-subif)#^Z R1# *Mar 1 22:10:01.480: %SYS-5-CONFIG_I: Configured from console by console R1#sh run in t      in t  t ip in     s 0/0.1 Building configuration... Current configuration : 177 bytes ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 103 end R1#sh run int s 0/0.1 2 Building configuration... Current configuration : 182 bytes ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 102 end R1#sh ip ospf nrei   ei Neighbor ID Pri State Dead Time Address Interface 17.100.1.2 1 FULL/DR 00:00:31 17.100.1.2 Ethernet0/1 180.40.7.98 0 FULL/ - 00:01:37 180.40.7.65 Serial0/0.2 17.57.100.2 1 FULL/DR 00:00:29 17.57.100.2 Ethernet0/0 R1#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 17.100.1.2 1 FULL/DR 00:00:31 17.100.1.2 Ethernet0/1 180.40.7.98 0 FULL/ - 00:01:59 180.40.7.65 Serial0/0.2 180.40.7.129 0 FULL/ - 00:00:39 180.40.7.33 Serial0/0.1 17.57.100.2 1 FULL/DR 00:00:30 17.57.100.2 Ethernet0/0 R1# *Mar 1 22:10:50.104: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial0/0.1 from LOADING to FULL, Loading Done R1# R1# R1# R1# R1# RACK11AS>5 [Resuming connection 5 to r5 ... ] 22:11:21: %SYS-5-CONFIG_I: Configured from console S5#config t sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:11:30/00:02:16, RP 180.40.7.129, flags: SPCL Incoming interface: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: Null (*, 224.0.1.40), 00:11:30/00:02:14, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:11:30/00:00:00 S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] * R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:08:30/00:03:18, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:11/00:03:18 FastEthernet0/1, Forward/Dense, 00:08:30/00:00:00 (*, 224.20.68.1), 00:09:21/00:02:37, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:08:49/00:02:36 FastEthernet0/1, Forward/Dense, 00:09:22/00:00:00 (*, 224.4.4.4), 00:09:07/00:02:53, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:09:07/00:00:00 (*, 224.6.6.6), 00:09:16/00:02:41, RP 180.40.7.129, flags: S --More--   Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:08:45/00:02:40 FastEthernet0/1, Forward/Dense, 00:09:17/00:00:00 (*, 224.7.7.7), 00:08:32/00:03:16, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:13/00:03:16 FastEthernet0/1, Forward/Dense, 00:08:32/00:00:00 (*, 224.0.1.40), 00:09:28/00:02:58, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:09:28/00:00:00 FastEthernet0/1, Forward/Dense, 00:09:28/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:09:28/00:00:00 R3# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip mrouteconfig t ping 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 96 ms S5#ping 224.20.68.1sh ip mroute config t ping 224.20.68.16.6.6  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 96 ms S5#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: . S5# RACK11AS>1 [Resuming connection 1 to r1 ... ] * R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#shut R1(config-subif)#^Z R1# *Mar 1 22:12:00.888: %PIM-5-NBRCHG: neighbor 180.40.7.33 DOWN on interface Serial0/0.1 (vrf default) non DR *Mar 1 22:12:00.892: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial0/0.1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 22:12:01.681: %SYS-5-CONFIG_I: Configured from console by console R1# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#h run | i ip pim sp help run | i ip pim sp ^ % Invalid input detected at '^' marker. R1#h run | i ip pim spsh run | i ip pim sp ip pim sparse-dense-mode ip pim sparse-dense-mode ip pim sparse-dense-mode ip pim sparse-dense-mode ip pim spt-threshold 1 R1# R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#p ip pim bi R1(config)#ip pim bidir-enable R1(config)# R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config)#cip pim bidir-enablecip pim bidir-enable  R2(config)#^Z R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pim bidir-enable R3(config)# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip pim bidir-enable S5(config)# RACK11AS>6 [Resuming connection 6 to r6 ... ] 22: S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim bidir-enable S6(config)# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip pim bidir-enable R7(config)# R7(config)#^Z R7#sh ip *Mar 1 22:12:49.158: %SYS-5-CONFIG_I: Configured from console by console R7#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.7.7.7), 00:00:08/00:02:51, RP 180.40.7.129, flags: SPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 00:24:15/00:02:51, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:24:15/00:00:00 R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 104 ms R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 108 ms Reply to request 0 from 180.40.7.130, 124 ms R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 104 ms R7#sh ip mo route IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:28/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (17.100.1.2, 224.4.4.4), 00:00:28/00:02:49, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.7.7.7), 00:00:45/00:02:42, RP 180.40.7.129, flags: SPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 00:24:52/00:02:35, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:24:52/00:00:00 R7#sh ip pim .rp   rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:21:46, expires: 00:02:43 R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Ma R3(config)#ip pim bidir-enablespt-threshold 1dr-priority 4294967294nt s 1/0 p pim rp-candidate fa 0/1 grou 1 int 10 ? bidir Group range treated in bidirectional shared-tree mode priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 grou 1 int 10 bi R3(config)#ip pim rp-candidate fa 0/1 grou 1 int 10 bidir R3(config)#^Z R3# *Mar 1 22:14:24.623: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Maconfig t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#^Z R2#sh i *Mar 1 22:14:33.978: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip pim rp map PIM Group-to-RP Mappings This system is the Bootstrap Router (v2) Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2, bidir Info source: 180.40.7.3 (?), via bootstrap, priority 0, holdtime 35 Uptime: 00:23:55, expires: 00:00:33 R2# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:22:47, expires: 00:03:06 R7#sh ip pim rp mapmroute ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4(config)#int fa 0/1 0 R4(config-if)#ip piom R4(config-if)#ip piom  m R4(config-if)#ip pim sp R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)#exit R4(config)#ip pim bi R4(config)#ip pim bidir-enable R4(config)#^Z R4# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 100 ms R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b ip pim bi ip pim bidir-enable ip pim spt-threshold 1 ip pim rp-candidate FastEthernet0/1 group-list 1 interval 10 bidir ip pim register-rate-limit 2 ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 --More--   R3# R3#configt  t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#r ^Z R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip dhcp ex R2(config)#ip dhcp excluded-address 180.407.98.7.98 R2(config)#ip dhcp poo ForS6 R2(dhcp-config)#client-identifier 0063.6973.636f.2d30.3030.612e.6634.3961.2e3$tifier 0063.6973.636f.2d30.3030.612e.6634.3961.2e32 .3338.3023.6973.636f.2d30.3030.612e.6634.3961.2e32.3338.302d .4661.302f.2d30.3030.612e.6634.3961.2e32.3338.302d.4661.302f .32 R2(dhcp-config)#host 180.40.7.97  /27 % Hostname contains one or more illegal characters. % Hostname "180.40.7.97/27" is not a legal LAT node name, Using "CISCO_8D3A80" 180.40.7.97/27(config)#int     host 180.40.7.97/27$0.612e.6634.3961.2e32.3338.302d.4661.302f.32ip dhcp poo ForS6  180.40.7.97/27(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   180.40.7.97/27(dhcp-config)#  host ? A.B.C.D IP address in dotted-decimal notation 180.40.7.97/27(dhcp-config)#host 180.40.7.97   /27 180.40.7.97/27(dhcp-config)#exit 180.40.7.97/27(config)#host R2 R2(config)#do sh qa  access-list R2(config)#int fa 0/1 R2(config-if)#ip hel R2(config-if)#ip help R2(config-if)#ip helper-address 17.                  m R2(config-if)#ip mun R2(config-if)#ip mun  R2(config-if)#ip multicast ? boundary Boundary for administratively scoped multicast addresses helper-map Broadcast to Multicast map OR Multicast to ip-address map netflow NetFlow accounting for multicast rate-limit Rate limit multicast data packets tagswitch Enable IP Multicast Tagswitching ttl-threshold TTL threshold for multicast packets R2(config-if)#ip multicast hel R2(config-if)#ip multicast helper-map ? A.B.C.D IP multicast address broadcast Broadcast address R2(config-if)#ip multicast helper-map bo  R2(config-if)#ip multicast helper-map broadcast ? A.B.C.D IP address R2(config-if)#ip multicast helper-map broadcast 226.6.6.6  ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R2(config-if)#ip multicast helper-map broadcast 226.6.6.6                                             exit R2(config)#access-list 100 per udp 180.,       j host 19 80.90.  4-0    40.7.97 host 2555.255     .255.255.255 eq t$ 100 per udp host 180.40.7.97 host 255.255.255.255 eq tf tp R2(config)#int fa0/1 R2(config-if)#ip mu help ? A.B.C.D IP multicast address broadcast Broadcast address R2(config-if)#ip mu help br R2(config-if)#ip mu help broadcast 226.6.6.6 ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R2(config-if)#ip mu help broadcast 226.6.6.6 100 ? R2(config-if)#ip mu help broadcast 226.6.6.6 100 R2(config-if)#^Z R2# RACK11AS>1 [Resuming connection 1 to r1 ... ] * R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#inbt    t s 0/0.2 R1(config-subif)#ip he R1(config-subif)#ip hel   mu R1(config-subif)#ip multicast              exit R1(config)#do sh access-list Standard IP access list 1 10 deny 224.20.73.1, wildcard bits 15.128.20.0 (75 matches) 20 permit any (90 matches) Standard IP access list 2 10 permit 239.0.0.0, wildcard bits 0.255.255.255 R1(config)#access-list 100 per udp host 226.6.6.6           180.40.7.97 host 226.6.6.6 eq tftp R1(config)#int s 0/0.2 R1(config-subif)#ip mu he R1(config-subif)#ip mu helper-map ? A.B.C.D IP multicast address broadcast Broadcast address R1(config-subif)#ip mu helper-map 226.6.6.6 ? A.B.C.D IP address R1(config-subif)#ip mu helper-map 226.6.6.6 17/.  .100.1.255 ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R1(config-subif)#ip mu helper-map 226.6.6.6 17.100.1.255 100 ? R1(config-subif)#ip mu helper-map 226.6.6.6 17.100.1.255 100 R1(config-subif)#^Z R1# *Mar 1 22:26:35.854: %SYS-5-CONFIG_I: Configured from console by console R1#deb ip mpa R1#deb ip mpacket de R1#deb ip mpacket detail IP multicast packets debugging is on (detailed) R1# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6(config)#^Z S6# 22:28:58: %SYS-5-CONFIG_I: Configured from console by consolecopy tftp run Address or name of remote host []? 255.255.255.255 Source filename []? lkuadsjfh Destination filename [running-config]? Accessing tftp://255.255.255.255/lkuadsjfh... RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#sh deb Generic IP: IP multicast packets debugging is on (detailed) R1#sg log Translating "sg" Translating "sg" % Unknown command or computer name, or unable to find computer address R1#sgh     sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 54 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: disabled, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 59 message lines logged R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#log buss Translating "buss" ^ % Invalid input detected at '^' marker. R1(config)#log buss  ff R1(config)#^Z R1# RACK11AS>6 [Resuming connection 6 to r6 ... ] %E S6#lkuadsjfh255.255.255.255copy tftp run  Address or name of remote host [255.255.255.255]? Source filename [lkuadsjfh]? Destination filename [running-config]? Accessing tftp://255.255.255.255/lkuadsjfh... RACK11AS>1 [Resuming connection 1 to r1 ... ] *Mar R1# *Mar 1 22:27:41.646: IP(0): MAC sa=DLCI 102 (Serial0/0.2) *Mar 1 22:27:41.646: IP(0): IP tos=0x0, len=46, id=0, ttl=253, prot=17 *Mar 1 22:27:41.646: IP(0): s=180.40.7.97 (Serial0/0.2) d=226.6.6.6 id=0, prot=17, len=50(46), mroute olist null R1# *Mar 1 22:27:45.644: IP(0): MAC sa=DLCI 102 (Serial0/0.2) *Mar 1 22:27:45.644: IP(0): IP tos=0x0, len=46, id=1, ttl=253, prot=17 *Mar 1 22:27:45.648: IP(0): s=180.40.7.97 (Serial0/0.2) d=226.6.6.6 id=1, prot=17, len=50(46), mroute olist null R1# *Mar 1 22:27:50.644: IP(0): MAC sa=DLCI 102 (Serial0/0.2) *Mar 1 22:27:50.644: IP(0): IP tos=0x0, len=46, id=2, ttl=253, prot=17 *Mar 1 22:27:50.644: IP(0): s=180.40.7.97 (Serial0/0.2) d=226.6.6.6 id=2, prot=17, len=50(46), mroute olist null R1#u all All possible debugging has been turned off R1#ip  *Mar 1 22:27:56.646: IP(0): MAC sa=DLCI 102 (Serial0/0.2) *Mar 1 22:27:56.646: IP(0): IP tos=0x0, len=46, id=3, ttl=253, prot=17 *Mar 1 22:27:56.646: IP(0): s=180.40.7.97 (Serial0/0.2) d=226.6.6.6 id=3, prot=17, len=50(46), mroute olist null R1#i deb ip pack IP packet debugging is on R1# R1# R1# R1# R1# R1# R1# R1# RACK11AS>6 [Resuming connection 6 to r6 ... ] RACK11AS>1 [Resuming connection 1 to r1 ... ] *Ma R1# *Mar 1 22:28:08.970: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast *Mar 1 22:28:09.459: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.13, len 58, rcvd 0 R1# *Mar 1 22:28:10.108: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.13, len 54, rcvd 0 *Mar 1 22:28:10.297: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast R1# *Mar 1 22:28:11.390: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:28:11.651: IP: tableid=0, s=180.40.7.97 (Serial0/0.2), d=17.100.1.255 (Ethernet0/1), routed via RIB *Mar 1 22:28:11.723: IP: s=17.57.100.1 (local), d=224.0.0.1 (Ethernet0/0), len 28, sending broad/multicast R1# *Mar 1 22:28:12.789: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:28:12.877: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.13, len 54, rcvd 0 *Mar 1 22:28:12.889: IP: s=17.100.1.1 (local), d=224.0.0.13 (Ethernet0/1), len 58, sending broad/multicast *Mar 1 22:28:12.925: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 54, sending broad/multicast *Mar 1 22:28:13.270: IP: s=17.57.100.2 (Ethernet0/0), d=224.20.73.1, len 28, rcvd 0 *Mar 1 22:28:13.742: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.13, len 58, rcvd 0 R1# *Mar 1 22:28:13.810: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 58, sending broad/multicast *Mar 1 22:28:14.728: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 54, sending broad/multicast R1# RACK11AS>6 [Resuming connection 6 to r6 ... ] %opy tftp run Address or name of remote host [255.255.255.255]? Source filename [lkuadsjfh]? Destination filename [running-config]? Accessing tftp://255.255.255.255/lkuadsjfh... RACK11AS>1 [Resuming connection 1 to r1 ... ] *Ma R1# *Mar 1 22:28:22.789: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:28:22.941: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 58, sending broad/multicast *Mar 1 22:28:23.651: IP: tableid=0, s=180.40.7.97 (Serial0/0.2), d=17.100.1.255 (Ethernet0/1), routed via RIB R1# *Mar 1 22:28:23.939: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 40, sending broad/multicast *Mar 1 22:28:23.939: IP: s=17.100.1.1 (local), d=224.0.0.13 (Ethernet0/1), len 40, sending broad/multicast R1# *Mar 1 22:28:25.161: IP: s=180.40.7.66 (local), d=224.0.0.5 (Serial0/0.2), len 80, sending broad/multicast R1#u all All possible debugging has been turned off R1# *Mar 1 22:28:28.651: IP: tableid=0, s=180.40.7.97 (Serial0/0.2), d=17.100.1.255 (Ethernet0/1), routed via RIB *Mar 1 22:28:28.971: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast *Mar 1 22:28:29.464: IP: s=180.40.7.129 (Serial0/0.2), d=224.0.0.2, len 44, rcvd 0 R1#sh    deb ? aaa AAA Authentication, Authorization and Accounting aal2_xgcpspi AAL2_XGCP Service Provider Interface. access-expression Boolean access expression adjacency adjacency alarm-interface Alarm Interface Card events all Enable all debugging alps ALPS debug information arp IP ARP and HP Probe transactions asnl Application Subscribe Notify Layer aspp ASPP information async Async interface information backhaul-session-manager Backhaul SM options backup Backup events bgp BGP information bsc BSC information bstun BSTUN information call Call Information callback Callback activity cca CCA activity ccaal2 ccaal2 information ccfrf11 CCFRF11 information cch323 CCH323 information --More--   ccm-manager Call Manager Application information ccsip CCSIP information ccswvoice ccswvoice information cdapi CDAPI information cdp CDP information ces-conn Connection Manager CES Client Info cgma Cisco Gateway Management Application Information chat Chat scripts activity clns CLNS information cls CLS Information cns CNS agents compress COMPRESS traffic condition Condition confmodem Modem configuration database conn Connection Manager information cops COPS crm Carrier Resource Manager info ctunnel Generic CTunnel Interface custom-queue Custom output queueing dampening Dampening decnet DECnet information dhcp DHCP client activity dialer Dial on Demand --More--   dialpeer Dialpeer info diffserv DiffServ COPS Client dlsw Data Link Switching (DLSw) events dnsix Dnsix information domain Domain Name System drip DRiP debug information dspapi Generic DSP API dspu DSPU Information dxi atm-dxi information eigrp EIGRP Protocol information entry Incoming queue entries ephone ethernet phone skinny protocol ethernet-interface Ethernet network interface events fastethernet Fast Ethernet interface information fax Fax frame-relay Frame Relay fras FRAS Debug fras-host FRAS Host Debug gssapi GSSAPI debugs h225 H.225 Library Debugging h245 H.245 Library Debugging hpi HPI (54x) DSP messages http HTTP Debugging --More--   R1#deb e int ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface Ethernet IEEE 802.3 Group-Async Async Group interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R1#deb int e o/o    0/0     0/0 ? R1#deb int e0/0 Condition 1 set R1# RACK11AS>6 [Resuming connection 6 to r6 ... ] % S6#copy tftp run Address or name of remote host [255.255.255.255]? Source filename [lkuadsjfh]? Destination filename [running-config]? Accessing tftp://255.255.255.255/lkuadsjfh... RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#u all All possible debugging has been turned off R1#sh db ^ % Invalid input detected at '^' marker. R1#sh deb Condition 1: interface Et0/0 (1 flags triggered) Flags: Et0/0 R1#sh debb u alldeb int e0/0 u all deb int e0/0 ndeb int e0/0 odeb int e0/0  deb int e0/0  This condition is the last interface condition set. Removing all conditions may cause a flood of debugging messages to result, unless specific debugging flags are first removed. Proceed with removal? [yes/no]: y Condition 1 has been removed R1# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#sh    deb ip palc  ck IP packet debugging is on R7# RACK11AS>6 [Resuming connection 6 to r6 ... ] RACK11AS>7 [Resuming connection 7 to r7 ... ] *Ma R7# *Mar 1 22:29:26.461: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast R7# *Mar 1 22:29:27.815: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0 R7# *Mar 1 22:29:32.643: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:29:32.667: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.1, len 28, rcvd 0 R7# *Mar 1 22:29:35.187: IP: s=180.40.7.129 (FastEthernet0/1), d=224.0.0.2, len 44, rcvd 0 *Mar 1 22:29:35.965: RACK11AS>6 [Resuming connection 6 to r6 ... ] %Err S6# S6# S6#copy tftp run Address or name of remote host [255.255.255.255]? Source filename [lkuadsjfh]? Destination filename [running-config]? Accessing tftp://255.255.255.255/lkuadsjfh... RACK11AS>7 [Resuming connection 7 to r7 ... ] 00.1.2 (local), d=224.7 R7# *Mar 1 22:29:46.462: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast R7# *Mar 1 22:29:52.644: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0 R7# *Mar 1 22:29:56.230: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 56, rcvd 0 *Mar 1 22:29:56.462: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#^Z R7# *Mar 1 22:30:02.644: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0 R7# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ip di R1(config-if)#ip directed-broadcast R1(config-if)#^Z R1# RACK11AS>7 [Resuming connection 7 to r7 ... ] *M R7# RACK11AS>7 6 [Resuming connection 6 to r6 ... ] % S6#copy tftp run Address or name of remote host [255.255.255.255]? Source filename [lkuadsjfh]? Destination filename [running-config]? Accessing tftp://255.255.255.255/lkuadsjfh... RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar 1 22:30:22. R7# *Mar 1 22:30:30.534: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 46, rcvd 2 R7# *Mar 1 22:30:32.646: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0 R7# *Mar 1 22:30:35.534: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 46, rcvd 2 *Mar 1 22:30:36.464: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast R7# *Mar 1 22:30:39.445: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast R7# *Mar 1 22:30:41.536: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 46, rcvd 2 R7# *Mar 1 22:30:42.646: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0 R7# *Mar 1 22:30:46.464: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast R7# *Mar 1 22:30:48.536: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 46, rcvd 2 R7# *Mar 1 22:30:52.646: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0 R7# *Mar 1 22:30:56.332: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 56, rcvd 0 *Mar 1 22:30:56.465: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast *Mar 1 22:30:56.537: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 46, rcvd 2 R7# *Mar 1 22:31:02.647: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:31:02.815: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.1, len 28, rcvd 0 R7# *Mar 1 22:31:04.109: IP: s=17.100.1.2 (local), d=224.7.7.7 (FastEthernet0/1), len 28, sending broad/multicast R7# *Mar 1 22:31:05.439: IP: s=180.40.7.129 (FastEthernet0/1), d=224.0.0.2, len 44, rcvd 0 R7#u al *Mar 1 22:31:06.465: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast R7#u all All possible debugging has been turned off R7#\ *Mar 1 22:31:08.116: IP: s=17.100.1.2 (local), d=224.0.1.40 (FastEthernet0/1), len 28, sending broad/multicast R7#\  RACK11AS>1 [Resuming connection 1 to r1 ... ] *Mar 1 R1#sh run int s 0/0.1 Building configuration... Current configuration : 187 bytes ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point shutdown frame-relay interface-dlci 103 end R1#sh run int s 0/0.1 2 Building configuration... Current configuration : 234 bytes ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map 226.6.6.6 17.100.1.255 100 ip ospf network point-to-multipoint frame-relay interface-dlci 102 end R1#sh ip in t e 0/1 ^ % Invalid input detected at '^' marker. R1#sh ip in t e 0/1t e 0/1 \t e 0/1 ^ % Invalid input detected at '^' marker. R1#sh ip in\t e 0/1t e 0/1  Ethernet0/1 is up, line protocol is up Internet address is 17.100.1.1/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is enabled Multicast reserved groups joined: 224.0.0.5 224.0.0.6 224.0.0.1 224.0.0.2 224.0.0.22 224.0.0.13 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF Fast switching turbo vector --More--   R1#deb ip pack IP packet debugging is on R1# RACK11AS>6 [Resuming connection 6 to r6 ... ] %E S6#copy tftp run Address or name of remote host [255.255.255.255]? Source filename [lkuadsjfh]? Destination filename [running-config]? Accessing tftp://255.255.255.255/lkuadsjfh... RACK11AS>1 [Resuming connection 1 to r1 ... ] *Ma0.5, len 80, rcvd 0 *Mar 1 22:34:18.685: IP: tableid=0, s=180.40.7.97 (Serial0/0.2), d=17.100.1.255 (Ethernet0/1), routed via RIB *Mar 1 22:34:18.889: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 58, sending broad/multicast *Mar 1 22:34:18.985: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast R1# R1# *Mar 1 22:34:20.311: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast *Mar 1 22:34:20.804: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.13, len 40, rcvd 0 R1# *Mar 1 22:34:21.389: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 R1#u all All possible debugging has been turned off R1# *Mar 1 22:34:22.683: IP: tableid=0, s=180.40.7.97 (Serial0/0.2), d=17.100.1.255 (Ethernet0/1), routed via RIB *Mar 1 22:34:22.799: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 R1#sh run |        deb ip pack IP packet debugging is on R1#ping 1 *Mar 1 22:35:24.557: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 54, sending broad/multicast *Mar 1 22:35:24.669: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 40, sending broad/multicast *Mar 1 22:35:24.669: IP: s=17.100.1.1 (local), d=224.0.0.13 (Ethernet0/1), len 40, sending broad/multicast *Mar 1 22:35:25.178: IP: s=180.40.7.66 (local), d=224.0.0.5 (Serial0/0.2), len 80, sending broad/multicast R1#ping 17.100.1.255 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.100.1.255, timeout is 2 seconds: *Mar 1 22:35:28.759: IP: s=17.100.1.1 (local), d=255.255.255.255 (Ethernet0/1), len 100, sending broad/multicast *Mar 1 22:35:28.759: IP: tableid=0, s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), routed via RIB *Mar 1 22:35:28.763: IP: s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), len 100, rcvd 3 *Mar 1 22:35:28.988: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast Reply to request 0 from 17.100.1.2, 4 ms *Mar 1 22:35:30.314: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast *Mar 1 22:35:30.759: IP: s=17.100.1.1 (local), d=255.255.255.255 (Ethernet0/1), len 100, sending broad/multicast *Mar 1 22:35:30.763: IP: tableid=0, s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), routed via RIB *Mar 1 22:35:30.763: IP: s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), len 100, rcvd 3 *Mar 1 22:35:31.388: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:35:31.736: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.13, len 58, rcvd 0 Reply to request 1 from 17.100.1.2, 4 ms *Mar 1 22:35:32.762: IP: s=17.100.1.1 (local), d=255.255.255.255 (Ethernet0/1), len 100, sending broad/multicast *Mar 1 22:35:32.766: IP: tableid=0, s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), routed via RIB *Mar 1 22:35:32.766: IP: s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), len 100, rcvd 3 *Mar 1 22:35:32.802: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 Reply to request 2 from 17.100.1.2, 4 ms *Mar 1 22:35:34.765: IP: s=17.100.1.1 (local), d=255.255.255.255 (Ethernet0/1), len 100, sending broad/multicast *Mar 1 22:35:34.769: IP: tableid=0, s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), routed via RIB *Mar 1 22:35:34.769: IP: s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), len 100, rcvd 3 *Mar 1 22:35:35.098: IP: s=17.100.1.1 (local), d=224.0.0.13 (Ethernet0/1), len 58, sending broad/multicast *Mar 1 22:35:35.531: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.13, len 58, rcvd 0 Reply to request 3 from 17.100.1.2, 4 ms *Mar 1 22:35:36.428: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 58, sending broad/multicast *Mar 1 22:35:36.769: IP: s=17.100.1.1 (local), d=255.255.255.255 (Ethernet0/1), len 100, sending broad/multicast *Mar 1 22:35:36.773: IP: tableid=0, s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), routed via RIB *Mar 1 22:35:36.773: IP: s=17.100.1.2 (Ethernet0/1), d=17.100.1.1 (Ethernet0/1), len 100, rcvd 3 Reply to request 4 from 17.100.1.2, 4 ms R1# *Mar 1 22:35:38.988: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast R1# *Mar 1 22:35:40.314: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast R1# *Mar 1 22:35:41.388: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 R1# *Mar 1 22:35:42.714: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.13, len 58, rcvd 0 *Mar 1 22:35:42.802: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 R1# *Mar 1 22:35:47.863: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 58, sending broad/multicast *Mar 1 22:35:48.656: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.5, len 80, rcvd 0 R1# *Mar 1 22:35:48.989: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast R1# *Mar 1 22:35:50.315: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast R1# *Mar 1 22:35:51.389: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 R1# *Mar 1 22:35:52.803: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:35:52.967: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.13, len 56, rcvd 0 *Mar 1 22:35:52.967: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 56, sending broad/multicast *Mar 1 22:35:52.971: IP: s=17.100.1.1 (local), d=224.0.0.13 (Ethernet0/1), len 56, sending broad/multicast R1# *Mar 1 22:35:55.179: IP: s=180.40.7.66 (local), d=224.0.0.5 (Serial0/0.2), len 80, sending broad/multicast R1# *Mar 1 22:35:58.989: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast R1# *Mar 1 22:36:00.315: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast *Mar 1 22:36:00.467: IP: s=180.40.7.129 (Serial0/0.2), d=224.0.0.2, len 44, rcvd 0 *Mar 1 22:36:01.217: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.13, len 58, rcvd 0 R1# *Mar 1 22:36:01.389: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 R1# *Mar 1 22:36:02.803: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:36:03.240: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.13, len 54, rcvd 0 R1# *Mar 1 22:36:05.179: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.13, len 58, rcvd 0 *Mar 1 22:36:05.676: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 58, sending broad/multicast *Mar 1 22:36:05.772: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.1, len 28, rcvd 0 R1# *Mar 1 22:36:06.253: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.13, len 54, rcvd 0 R1# *Mar 1 22:36:07.928: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 54, sending broad/multicast R1# *Mar 1 22:36:08.989: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast R1#con *Mar 1 22:36:10.316: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast *Mar 1 22:36:11.133: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 54, sending broad/multicast R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# *Mar 1 22:36:11.389: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:36:11.926: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.13, len 58, rcvd 0 R1(config)#no ip *Mar 1 22:36:12.776: IP: s=17.57.100.1 (local), d=224.0.0.1 (Ethernet0/0), len 28, sending broad/multicast *Mar 1 22:36:12.804: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:36:13.296: IP: s=17.57.100.2 (Ethernet0/0), d=224.20.73.1, len 28, rcvd 0 R1(config)#no ip cef R1(config)#int s 1  *Mar 1 22:36:17.704: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 58, sending broad/multicast *Mar 1 22:36:18.605: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.5, len 80, rcvd 0 R1(config)#int s 0/0.2 R1(config-subif)# *Mar 1 22:36:18.990: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast *Mar 1 22:36:19.787: IP: s=17.57.100.1 (local), d=224.0.1.40 (Ethernet0/0), len 28, sending broad/multicast R1(config-subif)#no ip *Mar 1 22:36:20.316: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast *Mar 1 22:36:21.001: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.13, len 40, rcvd 0 R1(config-subif)#no ip route % Ambiguous command: "no ip route" R1(config-subif)# *Mar 1 22:36:21.390: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 R1(config-subif)#no ip route- R1(config-subif)#no ip route-cache *Mar 1 22:36:22.804: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 R1(config-subif)#no ip route-cache R1(config-subif)# *Mar 1 22:36:24.627: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 54, sending broad/multicast *Mar 1 22:36:24.799: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 40, sending broad/multicast *Mar 1 22:36:24.799: IP: s=17.100.1.1 (local), d=224.0.0.13 (Ethernet0/1), len 40, sending broad/multicast *Mar 1 22:36:25.224: IP: s=180.40.7.66 (local), d=224.0.0.5 (Serial0/0.2), len 80, sending broad/multicast R1(config-subif)#int e 0/1 R1(config-if)#int e 0/1no ip route-cache R1(config-if)#^Z R1# *Mar 1 22:36:28.990: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast *Mar 1 22:36:29.014: IP: s=180.40.7.129 (Serial0/0.2), d=224.0.0.2, len 44, rcvd 0 *Mar 1 22:36:29.018: IP: s=180.40.7.129 (local), d=224.0.0.2 (Ethernet0/0), len 44, sending broad/multicast R1# RACK11AS>6 [Resuming connection 6 to r6 ... ] %Err S6#copy tftp run Address or name of remote host [255.255.255.255]? Source filename [lkuadsjfh]? Destination filename [running-config]? Accessing tftp://255.255.255.255/lkuadsjfh... RACK11AS>1 [Resuming connection 1 to r1 ... ] *M *Mar 1 22:36:35.393: IP: s=180.40.7.66 (local), d=224.0.0.13 (Serial0/0.2), len 58, sending broad/multicast R1# R1# *Mar 1 22:36:36.803: IP: tableid=0, s=180.40.7.97 (Serial0/0.2), d=17.100.1.255 (Ethernet0/1), routed via RIB R1# *Mar 1 22:36:38.991: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast R1# *Mar 1 22:36:40.317: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast R1# *Mar 1 22:36:41.390: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:36:41.803: IP: tableid=0, s=180.40.7.97 (Serial0/0.2), d=17.100.1.255 (Ethernet0/1), routed via RIB *Mar 1 22:36:41.867: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.13, len 58, rcvd 0 R1# *Mar 1 22:36:42.805: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 R1# *Mar 1 22:36:47.100: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 58, sending broad/multicast *Mar 1 22:36:47.805: IP: tableid=0, s=180.40.7.97 (Serial0/0.2), d=17.100.1.255 (Ethernet0/1), routed via RIB R1# *Mar 1 22:36:48.654: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:36:48.991: IP: s=17.100.1.1 (local), d=224.0.0.5 (Ethernet0/1), len 80, sending broad/multicast R1# *Mar 1 22:36:50.317: IP: s=17.57.100.1 (local), d=224.0.0.5 (Ethernet0/0), len 80, sending broad/multicast R1#co   *Mar 1 22:36:51.387: IP: s=17.57.100.2 (Ethernet0/0), d=224.0.0.5, len 80, rcvd 0 R1#u al *Mar 1 22:36:52.805: IP: s=17.100.1.2 (Ethernet0/1), d=224.0.0.5, len 80, rcvd 0 *Mar 1 22:36:53.066: IP: s=180.40.7.65 (Serial0/0.2), d=224.0.0.13, len 56, rcvd 0 *Mar 1 22:36:53.066: IP: s=17.57.100.1 (local), d=224.0.0.13 (Ethernet0/0), len 56, sending broad/multicast *Mar 1 22:36:53.066: IP: s=17.100.1.1 (local), d=224.0.0.13 (Ethernet0/1), len 56, sending broad/multicast R1#u all All possible debugging has been turned off R1#confi gt  t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ip route-c R1(config-if)#int s 0/0.1 2 R1(config-subif)#int s 0/0.2p route-c  R1(config-subif)#exit R1(config)#ip cef R1(config)#^Z R1#sh run *Mar 1 22:37:12.153: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int s 0/0.2 Building configuration... Current configuration : 234 bytes ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map 226.6.6.6 17.100.1.255 100 ip ospf network point-to-multipoint frame-relay interface-dlci 102 end R1#sh run int s 0/0.2 sh run | i access-list access-list 1 deny 224.20.73.1 15.128.20.0 access-list 1 permit any access-list 2 permit 239.0.0.0 0.255.255.255 access-list 100 permit udp host 180.40.7.97 host 226.6.6.6 eq tftp R1# R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run int     | b ip dhcp ip dhcp excluded-address 180.40.7.98 ! ip dhcp pool ForS6 host 180.40.7.97 255.255.255.224 client-identifier 0063.6973.636f.2d30.3030.612e.6634.3961.2e32.3338.302d.4661.302f.32 ! ip cef no ip domain lookup ip multicast-routing ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! --More--  ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 226.6.6.6 100 duplex auto --More--   speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown --More--  ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 --More--   no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ! access-list 100 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! ! ! --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#do sh ip ospf Routing Process "ospf 1" with ID 180.40.7.98 Supports only single TOS(TOS0) routes Supports opaque LSA Supports Link-local Signaling (LLS) Initial SPF schedule delay 5000 msecs Minimum hold time between two consecutive SPFs 10000 msecs Maximum wait time between two consecutive SPFs 10000 msecs Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs LSA group pacing timer 240 secs Interface flood pacing timer 33 msecs Retransmission pacing timer 66 msecs Number of external LSA 0. Checksum Sum 0x000000 Number of opaque AS LSA 0. Checksum Sum 0x000000 Number of DCbitless external and opaque AS LSA 0 Number of DoNotAge external and opaque AS LSA 0 Number of areas in this router is 1. 1 normal 0 stub 0 nssa External flood list length 0 Area BACKBONE(0) Number of interfaces in this area is 4 Area has no authentication SPF algorithm last executed 00:27:19.239 ago SPF algorithm executed 15 times Area ranges are --More--   R2(config)#router ospf 1 R2(config-router)#rout R2(config-router)#router-id 180.40.7.98 R2(config-router)#^x3 ^ % Invalid input detected at '^' marker. R2(config-router)# R2(config-router)# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip ospf Routing Process "ospf 1" with ID 180.40.7.129 Supports only single TOS(TOS0) routes Supports opaque LSA Supports Link-local Signaling (LLS) Initial SPF schedule delay 5000 msecs Minimum hold time between two consecutive SPFs 10000 msecs Maximum wait time between two consecutive SPFs 10000 msecs Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs LSA group pacing timer 240 secs Interface flood pacing timer 33 msecs Retransmission pacing timer 66 msecs Number of external LSA 0. Checksum Sum 0x000000 Number of opaque AS LSA 0. Checksum Sum 0x000000 Number of DCbitless external and opaque AS LSA 0 Number of DoNotAge external and opaque AS LSA 0 Number of areas in this router is 1. 1 normal 0 stub 0 nssa External flood list length 0 Area BACKBONE(0) Number of interfaces in this area is 3 Area has no authentication SPF algorithm last executed 00:27:43.932 ago SPF algorithm executed 15 times Area ranges are --More--   R3#onfig t ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotuer      uter ospf 1 R3(config-router)#router R3(config-router)#router-id 180.40.7.129 R3(config-router)#exit R3(config)#sh ip int brie ^ % Invalid input detected at '^' marker. R3(config)#sh ip int briedsh ip int brieosh ip int brie sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.129 YES manual up up Serial1/0 180.40.7.33 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.3 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--  Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down R3(config)#int lo 0 R3(config-if)#ip address 223.254.254.254      255.255.255.255 ^ % Invalid input detected at '^' marker. R3(config-if)#ip address 223.254.254 255.255.255.255. 255.255.255.2552 255.255.255.2555 255.255.255.2554 255.255.255.255 R3(config-if)# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#do sh ip in t  t brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.98 YES manual up up Serial1/0 unassigned YES manual up up Serial1/0.1 180.40.7.35 YES manual up up Serial1/0.2 180.40.7.65 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.2 YES manual up up Serial1/3 unassigned YES unset administratively down down --More--  Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down R2(config-router)#int lo 0 R2(config-if)#ip address 223.254.254.254 255.255.255.255 R2(config-if)#exit R2(config)#ip ms R2(config)#ip msdp ? cache-rejected-sa Store rejected SAs from all peers default-peer Default MSDP peer to accept SA messages from description Peer specific description filter-sa-request Filter SA-Requests from peer keepalive Configure keepalive parameters for a peer mesh-group Configure an MSDP mesh-group originator-id Configure MSDP Originator ID peer Configure an MSDP peer redistribute Inject multicast route entries into MSDP sa-filter Filter SA messages from peer sa-limit Configure SA limit for a peer shutdown Administratively shutdown MSDP peer timer MSDP timer ttl-threshold Configure TTL Threshold for MSDP Peer vrf Select VPN Routing/Forwarding instance R2(config)#ip msdp peer 180     ? Hostname or A.B.C.D Peer name or address R2(config)#ip msdp peer 180.40.7.3 ? connect-source Configure source address used for MSDP connection remote-as Configured AS number R2(config)#ip msdp peer 180.40.7.3   R2(config)# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#exit R3(config)#ip msd R3(config)#ip msdp peer 180., 40.7.2 R3(config)#do sh ip d n msdp peer MSDP Peer 180.40.7.2 (?), AS ? Connection status: State: Listen, Resets: 0, Connection source: none configured Uptime(Downtime): 00:00:11, Messages sent/received: 0/0 Output messages discarded: 0 Connection and counters cleared 00:00:11 ago SA Filtering: Input (S,G) filter: none, route-map: none Input RP filter: none, route-map: none Output (S,G) filter: none, route-map: none Output RP filter: none, route-map: none SA-Requests: Input filter: none Peer ttl threshold: 0 SAs learned from this peer: 0 Input queue size: 0, Output queue size: 0 R3(config)#do sh ip msdp peerip msdp peer 180.40.7.2exit ip address 223.254.254.254 255.255.255.255 255.255.255.255 .254 255.255.255.255 255.255.255.255 nt lo 0 do sh ip int briesh ip int brie exit router-id 180.40.7.129 ospf 1 ip pim rp-candidate fa 0/1 grou 1 int 10 bidir nip pim rp-candidate fa 0/1 grou 1 int 10 bidir oip pim rp-candidate fa 0/1 grou 1 int 10 bidir  ip pim rp-candidate fa 0/1 grou 1 int 10 bidir  R3(config)#no ip pim rp-candidate fa 0/1 grou 1 int 10 bidir gr *Mar 1 22:43:04.274: %MSDP-5-PEER_UPDOWN: Session to peer 180.40.7.2 going up R3(config)#no ip pim rp-candidate fa 0/1 grou 1 int 10 bidir ou 1 int 10 bidir int 10 bidir  int 10 bidir  int 10 bidir  int 10 bidir  int 10 bidir int 10 bidir  int 10 bidir  int 10 bidir  int 10 bidir int 10 bidir  int 10 bidir  int 10 bidir l int 10 bidir o int 10 bidir  int 10 bidir 0 int 10 bidir  R3(config)#no ip pim rp-candidate lo 0 int 10 bidir no ip pim rp-candidate lo 0 int 10 bidir  % Ambiguous command: "n ip pim rp-candidate lo 0 int 10 bidir " R3(config)#n ip pim rp-candidate lo 0 int 10 bidir n ip pim rp-candidate lo 0 int 10 bidir  Warning: PIMv2 not configured on Loopback0, Candidate-RP not advertised R3(config)#int lo 0 R3(config-if)#ip pim spo R3(config-if)#ip pim spo  R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)#exit R3(config)#exitip pim sparse-dense-mode i ^ % Invalid input detected at '^' marker. R3(config)#ip pim sparse-dense-mode iexit  *Mar 1 22:43:30.481: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback0 (vrf default) R3(config)#exitip pim sparse-dense-mode nt lo 0  ip pim rp-candidate lo 0 int 10 bidir R3(config)#^Z R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] *M R2(config)#int lo0 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#exit R2(config)#ixp *Mar 1 22:43:48.851: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback0 (vrf default) R2(config)#ixp rp R2(config)#ixp rp     p R2(config)#ip pim rp   R2(config)#ip pim rp--c R2(config)#ip pim rp--c c R2(config)#ip pim rp--c  c R2(config)#ip pim rp-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config)#ip pim rp-candidate lo 0 ? bidir Group range treated in bidirectional shared-tree mode group-list group-list interval RP candidate advertisement interval priority RP candidate priority R2(config)#ip pim rp-candidate lo 0 int 10 ? bidir Group range treated in bidirectional shared-tree mode priority RP candidate priority R2(config)#ip pim rp-candidate lo 0 int 10 bi R2(config)# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5(config)#ip pim bidir-enablespt-threshold 1^Z S5#config tping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: 22:47:46: %SYS-5-CONFIG_I: Configured from console by console Reply to request 0 from 180.40.7.97, 60 ms S5# S5# S5# S5#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 56 ms S5#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S5# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#u allconfig tdeb ip packping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#ping 224.4.4.4      .6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 60 ms R7#sh ip piom rp       m rpo    map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:02:00, expires: 00:02:54 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#no ip pim bi R7(config)#^Z R7# *Mar 1 22:46:03.948: %SYS-5-CONFIG_I: Configured from console by console R7# RACK11AS>6 [Resuming connection 6 to r6 ... ] %Erro S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#no ip pim bi S6(config)#^Z S6# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#no ip pim bi S5(config)#^Z S5# RACK11AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#no ip pim bi R4(config)# R4(config)#^Z R4# *Mar 1 22:49:09.482: %SYS-5-CONFIG_I: Configured from console by console R4#3 Trying 3... % Destination unreachable; gateway or host down % Unknown command or computer name, or unable to find computer address R4# R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip pim bi R3(config)#^Z R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config)#no ip pim bi R2(config)# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#no ip pim bi R1(config)#^Z R1# *Mar 1 22:47:49.081: %SYS-5-CONFIG_I: Configured from console by console R1# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#config tsh ip pim rp mapping 224.6.6.6  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 92 ms R7#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 56 ms R7#sh ip pim rp map PIM Group-to-RP Mappings R7#sh ip pim rp map PIM Group-to-RP Mappings R7#sh ip pim rp mapping 224.6.6.6 config t sh ip pim rp mapconfig t sh ip pim rp mapping 224.6.6.6  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 56 ms R7# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config)#do sh run | i ip pim rp R2(config)#do sh run | i ip pim rpno ip pim bi ip pim rp-candidate lo 0 int 10 bi   R2(config)# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip pim bi ip pim rp-candidate lo 0 int 10 bidir        R3(config)#^Z R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.6.6.6sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:12, expires: 00:03:12 R7#sh ip pim rp mapping 224.6.6.6  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 72 ms R7#ping 224.6.6.6sh ip pim rp mapping 224.6.6.6 sh ip pim rp mapping 224.6.6.6 config t sh ip pim rp mapping 224.6.6.6 4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 112 ms R7# RACK11AS>56 % 56 is not an open connection RACK11AS>5 [Resuming connection 5 to r5 ... ] 2 S5#config tping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 108 ms S5# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config)#^Z R2#sh *Mar 1 22:48:32.307: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip ms R2#sh ip msdp sa R2#sh ip msdp sa-cache MSDP Source-Active Cache - 0 entries R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh ip ms sa MSDP Source-Active Cache - 3 entries (17.57.100.2, 224.4.4.4), RP 223.254.254.254, AS ?,00:00:20/00:05:48, Peer 180.40.7.2 (17.100.1.2, 224.4.4.4), RP 223.254.254.254, AS ?,00:00:28/00:05:48, Peer 180.40.7.2 (17.100.1.2, 224.6.6.6), RP 223.254.254.254, AS ?,00:00:35/00:05:48, Peer 180.40.7.2 R3#^x4 % Unknown command or computer name, or unable to find computer address R3# R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#3config tping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 112 ms R4# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip msdp sa-cache MSDP Source-Active Cache - 1 entries (180.40.7.130, 224.7.7.7), RP 223.254.254.254, AS ?,00:00:06/00:05:53, Peer 180.40.7.3 R2#sh run I   | b ip pim,    ms R2#sh run | b ip pim msip msdp sa-cache run | b ip pim ms ms  ms  ms  R2#sh run | b ip msms  ip msdp peer 180.40.7.3 ! access-list 100 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R2#q sh ip   ru   run | b ip pim rp ip pim rp-candidate Loopback0 interval 10 ip msdp peer 180.40.7.3 ! access-list 100 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end --More--   R2#sh run int lo 0 Building configuration... Current configuration : 97 bytes ! interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode end R2# R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b     int lo 0 Building configuration... Current configuration : 97 bytes ! interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode end R3#sh run | b ip pim rp ip pim rp-candidate Loopback0 interval 10 ip pim register-rate-limit 2 ip msdp peer 180.40.7.2 ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login --More--   R3#sh run Building configuration... Current configuration : 1870 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R3 ! boot-start-marker boot-end-marker ! logging buffered 4096 debugging ! no network-clock-participate slot 1 no network-clock-participate wic 0 no aaa new-model ip subnet-zero ! ! ! ip cef --More--  no ip domain lookup ip multicast-routing ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! --More--  interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim dense-mode proxy-register list 100 duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.33 255.255.255.224 ip pim dr-priority 4294967294 --More--   ip pim sparse-dense-mode encapsulation frame-relay ip ospf network point-to-multipoint ip ospf hello-interval 10 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip pim sparse-dense-mode ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address --More--   shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 180.40.7.129 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim spt-threshold 1 ip pim rp-candidate Loopback0 interval 10 ip pim register-rate-limit 2 ip msdp peer 180.40.7.2 --More--  ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end --More--   R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip mu R3(config)#no ip multicast- R3(config)#no ip multicast-routing R3(config)#int fa 0/1 R3(config-if)#no ip pi,m    m R3(config-if)# *Mar 1 22:53:15.556: %PIM-5-NBRCHG: neighbor 180.40.7.130 DOWN on interface FastEthernet0/1 (vrf default) DR R3(config-if)#do sh       int s 1/0 R3(config-if)#int s 1/0no ip pim R3(config-if)#i *Mar 1 22:53:25.164: %PIM-5-NBRCHG: neighbor 180.40.7.35 DOWN on interface Serial1/0 (vrf default) non DR R3(config-if)#int s 1/2 R3(config-if)#int s 1/2no ip pim R3(config-if)# *Mar 1 22:53:30.957: %PIM-5-NBRCHG: neighbor 180.40.7.2 DOWN on interface Serial1/2 (vrf default) non DR R3(config-if)#exit R3(config)#no ip pim rp-ca R3(config)#no ip pim rp-candidate % Incomplete command. R3(config)#no ip pim rp-candidate lo 0 R3(config)#no ip msd peer 1   % Incomplete command. R3(config)#no ip msd peer     % Incomplete command. R3(config)#no ip msd peer 180.40.7.2 R3(config)# *Mar 1 22:53:58.346: %MSDP-5-PEER_UPDOWN: Session to peer 180.40.7.2 going down R3(config)#do sh run | i p   ip poi  im ip pim sparse-dense-mode ip pim dr-priority 4294967294 ip pim spt-threshold 1 ip pim register-rate-limit 2 R3(config)#a no ip pim spt-threshold 1 R3(config)#no R3(config)#no ip pim spt-threshold 1 ^ % Invalid input detected at '^' marker. R3(config)#no R3(config)#no ip pim spt-threshold 1no ip pim spt-threshold 1 no ip pim spt-threshold 1 no ip pim spt-threshold 1 no ip pim spt-threshold 1 no ip pim spt-threshold 1 o ip pim spt-threshold 1 no ip pim spt-threshold 1 no ip pim spt-threshold 1 no ip pim spt-threshold 1 no ip pim spt-threshold 1 no ip pim spt-threshold 1  ^ % Invalid input detected at '^' marker. R3(config)#no no ip pim spt-threshold 1no no ip pim spt-threshold 1  no ip pim spt-threshold 1  SPT threshold does not exist R3(config)#no ip pim register-rate-limit 2 R3(config)#sh run nit      ^ % Invalid input detected at '^' marker. R3(config)#int lo 0 R3(config-if)#ip p    no p ip pim R3(config-if)#inty s 1/0 ^ % Invalid input detected at '^' marker. R3(config-if)#int s 1/0 R3(config-if)#nm  no ip pim dr-priority 4294967294 R3(config-if)#^Z R3# *Mar 1 22:55:28.802: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int lo 1 R2(config-if)#ip addrees 2.2.2.2 255.255.255.255 ^ % Invalid input detected at '^' marker. R2(config-if)#ip addrees 2.2.2.2 255.255.255.255ip addrees 2.2.2.2 255.255.255.255 ss 2.2.2.2 255.255.255.255 R2(config-if)#int tu 0 R2(config-if)#ip address *Mar 1 22:56:20.263: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R2(config-if)#ip address 2.4  4.24.24.2 255.255.255.0 R2(config-if)#tun sou in t      lo1 R2(config-if)#tun des 4.4.4.4 R2(config-if)#ip pim spa R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#^Z R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] * R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#in tlo 1      t lo 0 R4(config-if)#ip add 4.4.4.4 255.255.255.255 R4(config-if)#int ut  tu 0 R4(config-if)#ip add 24.24 *Mar 1 22:59:32.530: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R4(config-if)#ip add 24.24.24.4 255.255.255.0 R4(config-if)#tun re sou      sou lo 0 R4(config-if)#tun dew   s 2.2.2.2 R4(config-if)#ip pim *Mar 1 22:59:50.770: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R4(config-if)#ip pim spo  p R4(config-if)#ip pim sparse-s d R4(config-if)#ip pim sparse-dense-mode R4(config-if)# *Mar 1 22:59:55.982: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4(config-if)# *Mar 1 22:59:58.234: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config-if)#^Z R4# *Mar 1 23:00:03.606: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:10, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:10, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:10, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:10, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:13, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:13, FastEthernet0/0 O 180.40.7.32/27 [110/1563] via 180.40.7.129, 00:00:13, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:13, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:13, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:13, FastEthernet0/0 R4# RACK11AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh    ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 80 ms R2# RACK11AS>6 [Resuming connection 6 to r6 ... ] 22: S6#sh    ping 244  24.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 136 ms R4#ping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 136 ms R4# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s0/0.1 R1(config-subif)#no shut R1(config-subif)#^Z R1# *Mar 1 23:00:02.780: %SYS-5-CONFIG_I: Configured from console by console R1# R1# R1# R1#^x   RACK11AS>z 4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:20, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:20, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:20, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:20, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:22, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:22, FastEthernet0/0 O 180.40.7.32/27 [110/1563] via 180.40.7.129, 00:00:22, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:22, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:22, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:22, FastEthernet0/0 R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip mrou R4(config)#ip mroute ? A.B.C.D Source address vrf Select VPN Routing/Forwarding instance R4(config)#ip mroute 0.0.0.0 ? A.B.C.D Network mask R4(config)#ip mroute 0.0.0.0 0.0.0.0 ? A.B.C.D RPF neighbor address or route ATM ATM interface Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing bgp Border Gateway Protocol (BGP) eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) isis ISO IS-IS iso-igrp IGRP for OSI networks mobile Mobile routes odr On Demand stub Routes ospf Open Shortest Path First (OSPF) rip Routing Information Protocol (RIP) --More--   R4(config)#ip mroute 0.0.0.0 0.0.0.0 u )     tu 0 R4(config)#^Z R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] *M R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip    run int l tu 0 Building configuration... Current configuration : 141 bytes ! interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode tunnel source Loopback0 tunnel destination 2.2.2.2 end R4#sh run int tu 0    fa 0/0 Building configuration... Current configuration : 216 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 88 ip pim sparse-dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4#sh run int fa 0/0tu 0 fa 0/0tu 0 ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:20, expires: 00:03:06 R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 36 ms S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp maprun int fa 0/0tu 0 ip pim rp mapconfig t sh ip routeping 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 136 ms R4#s clea ip mroute * R4#clea ip mroute *ping 224.7.7.7  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 132 ms R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Ma R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | interface ^ % Invalid input detected at '^' marker. R2#sh run | interface  binterface  interface  interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface Loopback1 ip address 2.2.2.2 255.255.255.255 ! interface Tunnel0 ip address 24.24.24.2 255.255.255.0 ip pim sparse-dense-mode tunnel source Loopback1 tunnel destination 4.4.4.4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! --More--   R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ru   un | b int interface Loopback0 ip address 4.4.4.4 255.255.255.255 ! interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode tunnel source Loopback0 tunnel destination 2.2.2.2 ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 88 ip pim sparse-dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto ! interface ATM1/0 ip address 192.10.32.11 255.255.255.0 ip nat outside no atm ilmi-keepalive pvc 0/72 --More--   R4#sh run | i ip mroute ip mroute 0.0.0.0 0.0.0.0 Tunnel0 R4# R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#no ip mroute 0.0.0.0 0.0.0.0 Tunnel0 R4(config)#int tu 0 R4(config-if)#ip opsp     =s  spf co 1 R4(config-if)#^Z R4#sh *Mar 1 23:07:07.810: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip ospf      *Mar 1 23:07:11.526: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 23:07:12.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 23:07:12.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 23:07:12.530: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4#sh ip o       confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#do a sh access0 -;l  list Standard IP access list IPNAT 10 permit 180.40.7.0, wildcard bits 0.0.0.255 (81 matches) 20 permit 17.0.0.0, wildcard bits 0.255.255.255 (59 matches) R4(config)#access-list 1 den 2.2.2.2 2   R4(config)#access-list 1 den 2.2.2.2              *Mar 1 23:08:12.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 23:08:12.578: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4(config)#access-list 1 per any R4(config)#router ospf 1 R4(config-router)# *Mar 1 23:08:18.326: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config-router)#dist R4(config-router)#distr R4(config-router)#distribute-list 1 in tun 0 R4(config-router)#^Z R4#sh ip *Mar 1 23:08:32.194: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:10, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:10, Tunnel0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:10, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:10, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:10, FastEthernet0/0 [110/2] via 24.24.24.2, 00:00:10, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 --More--   180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:13, FastEthernet0/0 [110/782] via 24.24.24.2, 00:00:13, Tunnel0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:13, FastEthernet0/0 O 180.40.7.32/27 [110/782] via 24.24.24.2, 00:00:13, Tunnel0 O 180.40.7.66/32 [110/782] via 180.40.7.129, 00:00:13, FastEthernet0/0 [110/782] via 24.24.24.2, 00:00:13, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:13, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:13, Tunnel0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:17, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:17, Tunnel0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:17, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:17, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:17, FastEthernet0/0 [110/2] via 24.24.24.2, 00:00:17, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 --More--   180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:19, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:19, FastEthernet0/0 O 180.40.7.66/32 [110/782] via 180.40.7.129, 00:00:19, FastEthernet0/0 R4# *Mar 1 23:08:42.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 23:08:42.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 23:08:42.530: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4# *Mar 1 23:08:52.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 23:08:52.578: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4#sh ip routeconfi t  *Mar 1 23:08:58.326: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4#confi tsh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:03, FastEthernet0/0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:03, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:03, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:03, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--   R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:07, FastEthernet0/0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:07, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:07, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:07, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--   R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:00, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:00, Tunnel0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:00, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:00, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:00, FastEthernet0/0 [110/2] via 24.24.24.2, 00:00:00, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 --More--   R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:05, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:05, Tunnel0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:05, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:05, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:05, FastEthernet0/0 [110/2] via 24.24.24.2, 00:00:05, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 --More--   180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:07, FastEthernet0/0 [110/782] via 24.24.24.2, 00:00:07, Tunnel0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:07, FastEthernet0/0 O 180.40.7.32/27 [110/782] via 24.24.24.2, 00:00:07, Tunnel0 O 180.40.7.66/32 [110/782] via 180.40.7.129, 00:00:07, FastEthernet0/0 [110/782] via 24.24.24.2, 00:00:07, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:07, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:07, Tunnel0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:12, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:12, Tunnel0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:12, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:12, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:12, FastEthernet0/0 [110/2] via 24.24.24.2, 00:00:12, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 --More--   R4#   *Mar 1 23:09:22.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 23:09:22.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 23:09:22.530: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4# *Mar 1 23:09:32.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 23:09:32.582: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4# *Mar 1 23:09:38.330: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4# *Mar 1 23:10:02.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 23:10:02.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 23:10:02.530: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4# *Mar 1 23:10:12.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 23:10:12.578: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4# *Mar 1 23:10:18.338: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#no access-list 1 R4(config)#rouetr ospf          ter ospf *Mar 1 23:10:31.526: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 23:10:32.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 23:10:32.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 23:10:32.530: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config)#router ospf 1 R4(config-router)#router ospf 1no access-list 1distribute-list 1 in tun 0ndistribute-list 1 in tun 0odistribute-list 1 in tun 0 distribute-list 1 in tun 0 R4(config-router)#int tu 0 R4(config-if)#no ip ospf co R4(config-if)#^Z R4# *Mar 1 23:11:32.190: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 23:11:32.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 23:11:32.578: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4# *Mar 1 23:11:38.334: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#routwer    ter eigrp 1 R4(config-router)#net 4.4.4.4 0.0.0.0 R4(config-router)#no auto R4(config-router)#net 180.40.73 .130 0.0.0.0 R4(config-router)#^Z R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router eigrp 1 R3(config-router)#nop auto ^ % Invalid input detected at '^' marker. R3(config-router)#nop autonop auto  R3(config-router)#net 180.40.7.129 0.0.0.0 R3(config-router)#net 180.40.7.129 0.0.0.0 0.0.0.0  0.0.0.0  0.0.0.0 3 0.0.0.0 R3(config-router)# *Mar 1 23:10:37.243: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor 180.40.7.130 (FastEthernet0/1) is up: new adjacency R3(config-router)#^Z R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] * R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eigrp 1 R2(config-router)#no auto R2(config-router)#net 2.2.2.2 0.0.0.0 R2(config-router)#no   =et   et 180.40.7.2 0.0.0.0 R2(config-router)#^Z R2# *Mar 1 23:11:08.595: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 23:11:08.739: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor 180.40.7.3 (Serial1/2) is up: new adjacency R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] *M R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:01:56, FastEthernet0/0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:01:56, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/20642560] via 180.40.7.129, 00:00:08, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:01:56, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:00:37, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:01:58, FastEthernet0/0 O 180.40.7.32/27 [110/846] via 180.40.7.129, 00:01:58, FastEthernet0/0 O 180.40.7.66/32 [110/782] via 180.40.7.129, 00:01:58, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:01:58, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:01:58, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:02:12, FastEthernet0/0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:02:12, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/20642560] via 180.40.7.129, 00:00:24, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:02:12, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:00:53, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:02:14, FastEthernet0/0 O 180.40.7.32/27 [110/846] via 180.40.7.129, 00:02:14, FastEthernet0/0 O 180.40.7.66/32 [110/782] via 180.40.7.129, 00:02:14, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:02:14, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:02:14, FastEthernet0/0 R4#confi gt ^ % Invalid input detected at '^' marker. R4#in  config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int tu 0 R4(config-if)#ip ospf co 1 R4(config-if)#^Z R4# *Mar 1 23:14:15.262: %SYS-5-CONFIG_I: Configured from console by console R4#config t gtsh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:01, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:01, Tunnel0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:01, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:01, Tunnel0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/20642560] via 180.40.7.129, 00:00:44, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:02, FastEthernet0/0 [110/2] via 24.24.24.2, 00:00:02, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets --More--  C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:01:12, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.32/27 [110/782] via 24.24.24.2, 00:00:02, Tunnel0 O 180.40.7.66/32 [110/782] via 180.40.7.129, 00:00:02, FastEthernet0/0 [110/782] via 24.24.24.2, 00:00:02, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:02, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:02, Tunnel0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:05, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:05, Tunnel0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:05, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:05, Tunnel0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/20642560] via 180.40.7.129, 00:00:49, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:06, FastEthernet0/0 [110/2] via 24.24.24.2, 00:00:06, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets --More--  C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:01:18, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:08, FastEthernet0/0 O 180.40.7.32/27 [110/782] via 24.24.24.2, 00:00:08, Tunnel0 O 180.40.7.66/32 [110/782] via 180.40.7.129, 00:00:08, FastEthernet0/0 [110/782] via 24.24.24.2, 00:00:08, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:08, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:08, Tunnel0 R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#configf    t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no in t % Incomplete command. R3(config)#, no in tlo==      t lo 0 R3(config)#^Z R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 180.40.7.129, 00:00:01, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:01, Tunnel0 O 17.100.1.0 [110/792] via 180.40.7.129, 00:00:01, FastEthernet0/0 [110/792] via 24.24.24.2, 00:00:01, Tunnel0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/20642560] via 180.40.7.129, 00:01:38, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 24.24.24.2, 00:00:02, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More--  C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:02:08, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:04, FastEthernet0/0 O 180.40.7.32/27 [110/782] via 24.24.24.2, 00:00:04, Tunnel0 O 180.40.7.66/32 [110/782] via 180.40.7.129, 00:00:04, FastEthernet0/0 [110/782] via 24.24.24.2, 00:00:04, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:04, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:04, Tunnel0 R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 40 ms S6# RACK11AS>c7 [confirm] [OK] RACK11AS>x5 Translating "x5" Translating "x5" % Unknown command or computer name, or unable to find computer address RACK11AS> [Resuming connection 6 to r6 ... ] RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#ping 24 24.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 88 ms S5# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh ru n  n | b router eigrp router eigrp 1 network 2.2.2.2 0.0.0.0 network 180.40.7.2 0.0.0.0 no auto-summary ! router ospf 1 router-id 180.40.7.98 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 10 ip msdp peer 180.40.7.3 ! access-list 100 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! --More--   R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run | b eigrp router eigrp 1 network 180.40.7.3 0.0.0.0 network 180.40.7.129 0.0.0.0 no auto-summary ! router ospf 1 router-id 180.40.7.129 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! ! --More--   R3# R3# R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ru n  n i | b router router eigrp 1 network 4.4.4.4 0.0.0.0 network 180.40.7.130 0.0.0.0 no auto-summary ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip nat inside source list IPNAT interface ATM1/0 overload no ip http server no ip http secure-server ip classless ! ip pim spt-threshold 1 ! ! ip access-list standard IPNAT permit 180.40.7.0 0.0.0.255 permit 17.0.0.0 0.255.255.255 ! ! ! --More--   R4#sh run in t tu       t tu 0 Building configuration... Current configuration : 157 bytes ! interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode ip ospf cost 1 tunnel source Loopback0 tunnel destination 2.2.2.2 end R4# R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int tu 0 R4(config-if)#int tu 0p ospf co 1nip ospf co 1 ip ospf co 1oip ospf co 1ip ospf co 1 ip ospf co 1 oip ospf co 1 ip ospf co 1 R4(config-if)#exit R4(config)#no router eigrp 1 RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#no router eigrp 1 RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 23:16:44.778: %DUAL-5-NBRCH *Mar 1 23:16:51.357: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor 180.40.7.2 (Serial1/2) is down: Interface Goodbye received R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no rotuer      t uter eigrp 1 R3(config)# R3(config)#router soffp=      ospf 1 R3(config-router)#net 180.40.7.3 0.0.0.0 area 234 R3(config-router)# *Mar 1 23:17:24.106: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-router)#net 180.40.7.3 0.0.0.0 area 234 *Mar 1 23:17:24.106: %OSPF-6-AREACHG: 180.40.7.3/32 changed from area 0 to area 234 R3(config-router)#net 180.40.7.3 0.0.0.0 area 234 *Mar 1 23:17:24.675: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.2, Serial1/2 R3(config-router)#net 180.40.7.3 0.0.0.0 area 234 0.0.0.0 area 234 1 0.0.0.0 area 2342 0.0.0.0 area 2349 0.0.0.0 area 234 R3(config-router)# *Mar 1 23:17:31.747: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.11 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 23:17:31.747: %OSPF-6-AREACHG: 180.40.7.129/32 changed from area 0 to area 234 R3(config-router)#^Z R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] *Ma R4(config)#router ospf 1 R4(config-router)#net 4.4.4.4 0.0.0.0 area *Mar 1 23:20:11.526: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 23:20:12.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 23:20:12.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 23:20:12.530: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-router)#net 4.4.4.4 0.0.0.0 area 234 R4(config-router)#net *Mar 1 23:20:14.150: %OSPF-6-AREACHG: 4.4.4.4/32 changed from area 0 to area 234 R4(config-router)#net 180.40.7.130 0.00..0.0. .0. .0.0 area 234 R4(config-router)# *Mar 1 23:20:27.554: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-router)# *Mar 1 23:20:27.558: %OSPF-6-AREACHG: 180.40.7.130/32 changed from area 0 to area 234 R4(config-router)#^Z R4# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar *Mar 1 23:18:01.944: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from FULL to DOWN, Neighbor Down: Dead timer expired R2(config)# R2(config)#routeer    r ospf 1 R2(config-router)#net 1 2.2.2.2 0..0.0 \    0.0.0 arae    ea 234 R2(config-router)#net *Mar 1 23:18:22.101: %OSPF-6-AREACHG: 2.2.2.2/32 changed from area 0 to area 234 R2(config-router)#net 180.40.7.2 0.0.0.0 area 234 R2(config-router)# *Mar 1 23:18:29.710: %OSPF-6-AREACHG: 180.40.7.2/32 changed from area 0 to area 234 R2(config-router)#^Z R2# *Mar 1 23:18:31.276: %SYS-5-CONFIG_I: Configured from console by console R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] *Mar 1 23: R4#sh ip 0r  route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4# *Mar 1 23:21:07.578: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O IA 17.57.100.0 [110/792] via 180.40.7.129, 00:00:00, FastEthernet0/0 O IA 17.100.1.0 [110/792] via 180.40.7.129, 00:00:00, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:00, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O IA 223.254.254.254 [110/783] via 180.40.7.129, 00:00:00, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:01, FastEthernet0/0 --More--  O IA 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:03, FastEthernet0/0 O IA 180.40.7.32/27 [110/846] via 180.40.7.129, 00:00:03, FastEthernet0/0 O IA 180.40.7.66/32 [110/782] via 180.40.7.129, 00:00:03, FastEthernet0/0 O IA 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:03, FastEthernet0/0 O IA 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:03, FastEthernet0/0 R4# *Mar 1 23:21:22.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 23:21:22.566: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O IA 17.57.100.0 [110/792] via 180.40.7.129, 00:00:04, FastEthernet0/0 O IA 17.100.1.0 [110/792] via 180.40.7.129, 00:00:04, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:14, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O IA 223.254.254.254 [110/783] via 180.40.7.129, 00:00:04, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:16, FastEthernet0/0 O IA 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:06, FastEthernet0/0 O IA 180.40.7.32/27 [110/846] via 180.40.7.129, 00:00:06, FastEthernet0/0 O IA 180.40.7.66/32 [110/782] via 180.40.7.129, 00:00:06, FastEthernet0/0 O IA 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:06, FastEthernet0/0 O IA 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:06, FastEthernet0/0 R4# *Mar 1 23:21:28.298: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:29, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 O 180.40.7.0 [110/782] via 180.40.7.129, 00:00:29, FastEthernet0/0 O 180.40.7.33/32 [110/11892] via 24.24.24.2, 00:00:00, Tunnel0 O 180.40.7.32/27 [110/11892] via 24.24.24.2, 00:00:00, Tunnel0 O 180.40.7.66/32 [110/11892] via 24.24.24.2, 00:00:00, Tunnel0 --More--  O 180.40.7.65/32 [110/11111] via 24.24.24.2, 00:00:00, Tunnel0 O 180.40.7.96/27 [110/11112] via 24.24.24.2, 00:00:00, Tunnel0 R4#sh ip ospf data OSPF Router with ID (192.10.32.11) (Process ID 1) Router Link States (Area 0) Link ID ADV Router Age Seq# Checksum Link count 17.57.100.2 17.57.100.2 1506 0x8000002C 0x0095A6 1 17.100.1.2 17.100.1.2 1306 0x8000002C 0x0065C0 1 180.40.7.66 180.40.7.66 1192 0x8000003A 0x0079E1 6 180.40.7.97 180.40.7.97 1398 0x8000002F 0x00ED01 1 180.40.7.98 180.40.7.98 49 0x80000045 0x005C90 8 180.40.7.129 180.40.7.129 136 0x80000035 0x009DDD 3 192.10.32.11 192.10.32.11 49 0x80000046 0x009066 3 Net Link States (Area 0) Link ID ADV Router Age Seq# Checksum 17.57.100.2 17.57.100.2 1506 0x8000002A 0x00AB2D 17.100.1.2 17.100.1.2 1306 0x8000000E 0x005C41 180.40.7.98 180.40.7.98 1616 0x8000002A 0x00E037 Summary Net Link States (Area 0) --More--  Link ID ADV Router Age Seq# Checksum 2.2.2.2 180.40.7.98 83 0x80000001 0x001CD1 2.2.2.2 180.40.7.129 68 0x80000001 0x00FEBF 2.2.2.2 192.10.32.11 70 0x80000001 0x00A488 4.4.4.4 180.40.7.98 58 0x80000001 0x00676D 4.4.4.4 180.40.7.129 68 0x80000001 0x000FB6 4.4.4.4 192.10.32.11 123 0x80000001 0x00A095 180.40.7.0 180.40.7.98 78 0x80000001 0x00F42D 180.40.7.0 180.40.7.129 143 0x80000001 0x003AC8 180.40.7.0 192.10.32.11 70 0x80000001 0x00DF91 180.40.7.128 180.40.7.98 53 0x80000003 0x00F5A8 180.40.7.128 180.40.7.129 62 0x80000003 0x009DF1 180.40.7.128 192.10.32.11 64 0x80000003 0x0039C5 Router Link States (Area 234) Link ID ADV Router Age Seq# Checksum Link count 180.40.7.98 180.40.7.98 77 0x80000003 0x003E0E 3 180.40.7.129 180.40.7.129 73 0x80000004 0x005612 3 192.10.32.11 192.10.32.11 75 0x80000003 0x002432 2 Net Link States (Area 234) --More--  Link ID ADV Router Age Seq# Checksum 180.40.7.130 192.10.32.11 75 0x80000001 0x007031 Summary Net Link States (Area 234) Link ID ADV Router Age Seq# Checksum 17.57.100.0 180.40.7.98 98 0x80000001 0x00939A 17.57.100.0 180.40.7.129 152 0x80000001 0x00D836 17.57.100.0 192.10.32.11 44 0x80000001 0x0003E8 17.100.1.0 180.40.7.98 98 0x80000001 0x00D293 17.100.1.0 180.40.7.129 152 0x80000001 0x00182F 17.100.1.0 192.10.32.11 44 0x80000001 0x0042E1 24.24.24.0 180.40.7.98 63 0x80000001 0x009982 24.24.24.0 180.40.7.129 62 0x80000001 0x007C70 24.24.24.0 192.10.32.11 54 0x80000001 0x007AF1 180.40.7.32 180.40.7.98 98 0x80000001 0x00B34E 180.40.7.32 180.40.7.129 152 0x80000001 0x007B27 180.40.7.32 192.10.32.11 44 0x80000001 0x00239C 180.40.7.33 180.40.7.98 99 0x80000001 0x00647D 180.40.7.33 180.40.7.129 153 0x80000001 0x000CC6 180.40.7.33 192.10.32.11 45 0x80000001 0x00D3CB 180.40.7.65 180.40.7.98 99 0x80000001 0x00854C 180.40.7.65 180.40.7.129 153 0x80000001 0x00683A --More--  180.40.7.65 192.10.32.11 45 0x80000001 0x00F49A 180.40.7.66 180.40.7.98 110 0x80000001 0x0019A7 180.40.7.66 180.40.7.129 164 0x80000001 0x005E43 180.40.7.66 192.10.32.11 56 0x80000001 0x0088F5 180.40.7.96 180.40.7.98 110 0x80000001 0x009D33 180.40.7.96 180.40.7.129 164 0x80000001 0x008021 180.40.7.96 192.10.32.11 56 0x80000001 0x000D81 192.10.32.0 180.40.7.98 66 0x80000001 0x006315 192.10.32.0 180.40.7.129 64 0x80000001 0x004603 192.10.32.0 192.10.32.11 145 0x80000001 0x00B5A5 223.254.254.254 180.40.7.98 110 0x80000001 0x003BDD 223.254.254.254 180.40.7.129 164 0x80000001 0x001ECB 223.254.254.254 192.10.32.11 56 0x80000001 0x00AA2C R4#^x5 % Unknown command or computer name, or unable to find computer address R4# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 108 ms S5# RACK11AS>2 [Resuming connection 2 to r2 ... ] * R2#sh run | b router router ospf 1 router-id 180.40.7.98 log-adjacency-changes network 2.2.2.2 0.0.0.0 area 234 network 180.40.7.2 0.0.0.0 area 234 network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 10 ip msdp peer 180.40.7.3 ! access-list 100 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! ! --More--   R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run | b router router ospf 1 router-id 180.40.7.129 log-adjacency-changes network 180.40.7.3 0.0.0.0 area 234 network 180.40.7.129 0.0.0.0 area 234 network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! ! ! ! ! --More--   R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b router router ospf 1 log-adjacency-changes network 4.4.4.4 0.0.0.0 area 234 network 180.40.7.130 0.0.0.0 area 234 network 0.0.0.0 255.255.255.255 area 0 ! ip nat inside source list IPNAT interface ATM1/0 overload no ip http server no ip http secure-server ip classless ! ip pim spt-threshold 1 ! ! ip access-list standard IPNAT permit 180.40.7.0 0.0.0.255 permit 17.0.0.0 0.255.255.255 ! ! ! ! ! ! --More--   R4#