=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.03.07 14:39:54 =~=~=~=~=~=~=~=~=~=~=~= R3# R3# R3#sh    confiug    g t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 87 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 custom-queue-list 1 end R3(config-if)#no custom-queue-list 1 R3(config-if)# R3(config-if)#exit R3(config)#do sh class Class Map match-all Prec1 (id 1) Match precedence 1 Class Map match-all Prec3 (id 2) Match precedence 3 Class Map match-any class-default (id 0) Match any R3(config)#class-map FTP R3(config-cmap)#match pro R3(config-cmap)#match protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 --More--   custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching (Direct encapsulation only) dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) --More--   R3(config-cmap)#match protocol ftp R3(config-cmap)#do sh ip nTar     bar port ftp port-map ftp tcp 21 R3(config-cmap)# R3(config-cmap)# R3(config-cmap)#p match pro ip ? R3(config-cmap)#match pro ip              do sh ip nbar port ftpmatch protocol ftp nmatch protocol ftpomatch protocol ftp match protocol ftp R3(config-cmap)#exit R3(config)#do sh access-list Extended IP access list 100 10 permit icmp host 100.1.1.1 host 20.10.1.2 echo (20 matches) 20 permit icmp host 100.1.1.1 host 20.10.1.2 echo-reply Extended IP access list 101 10 permit icmp host 100.1.1.1 host 20.10.1.1 echo (10 matches) 20 permit icmp host 100.1.1.1 host 20.10.1.1 echo-reply Extended IP access list 102 10 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo-reply 20 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo (35 matches) R3(config)#access-list 103 per tcp any any eq 21 R3(config)#access-list 103 per tcp any any eq 21 0 R3(config)#access-list 103 per tcp any any eq 20 eq 20  eq 20  eq 20  eq 20  no access-list 103 R3(config)#accessno access-list 103access-list 103 per tcp any any eq 20 R3(config)#access-list 103 per tcp any any eq 200 any eq 20 any  eq 20 any  eq 20 any  R3(config)#access-list 103 per tcp any eq 20 anyany eq 20 no access-list 103 access-list 103 per tcp any any eq 201do sh access-list exit no match protocol ftpdo sh ip nbar port ftpmatch protocol ftp class-map FTP  R3(config-cmap)#match pro R3(config-cmap)#match protocol ftp R3(config-cmap)#match       match protocol ftpclass-map FTP mFTPaFTPtFTPcFTPhFTP FTPFTP -FTPaFTPnFTPyFTP FTP R3(config-cmap)#match acc R3(config-cmap)#match access-group 103 R3(config-cmap)#dos h      sh run | b class class-map match-all Prec1 match precedence 1 class-map match-all Prec3 match precedence 3 class-map match-any FTP match protocol ftp match access-group 103 ! ! policy-map test class Prec1 class Prec3 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto --More--   R3(config-cmap)#exit R3(config)#class s R3(config)#class-map Telnn et ^ % Invalid input detected at '^' marker. R3(config)#class-map Telnn etet et  R3(config-cmap)#match pro telnet R3(config-cmap)#exit R3(config)#pol R3(config)#policy-map Prob9 R3(config-pmap)#class R3(config-pmap)#class FTp P R3(config-pmap-c)#ban R3(config-pmap-c)#bandwidth rte  e R3(config-pmap-c)#bandwidth remaining p R3(config-pmap-c)#bandwidth remaining percent 50 R3(config-pmap-c)#exit R3(config-pmap)#clas R3(config-pmap)#class Telnet R3(config-pmap-c)#class Telnetexit bandwidth remaining percent 50  25 R3(config-pmap-c)#class class-default R3(config-pmap-c)#class class-defaultbandwidth remaining percent 25 R3(config-pmap-c)#int s 1/2 R3(config-if)#ma R3(config-if)#max R3(config-if)#max-reserved-bandwidth 100 R3(config-if)#ser out Prob9 R3(config-if)#^Z R3#sh qu *Mar 2 05:34:27.484: %SYS-5-CONFIG_I: Configured from console by console R3#sh queueing int s 1/2 Interface Serial1/2 queueing strategy: fair Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: Class-based queueing Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 3/3 (allocated/max allocated) Available Bandwidth 128 kilobits/sec R3#sh    sh pol int s 1/2 Serial1/2 Service-policy output: Prob9 Class-map: FTP (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp 0 packets, 0 bytes 5 minute rate 0 bps Match: access-group 103 0 packets, 0 bytes 5 minute rate 0 bps Queueing Output Queue: Conversation 41 Bandwidth remaining 50 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet --More--   Queueing Output Queue: Conversation 42 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 8 packets, 762 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Output Queue: Conversation 43 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 R3#~sh pol int s 1/2~~~~~~~~~~~  % Unknown command or computer name, or unable to find computer address R3#180.40.7.2 Trying 180.40.7.2 ... Open R2# R2# R2# R2# R2#q [Connection to 180.40.7.2 closed by foreign host] R3#180.40.7.2~ sh pol int s 1/2 Serial1/2 Service-policy output: Prob9 Class-map: FTP (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp 0 packets, 0 bytes 5 minute rate 0 bps Match: access-group 103 0 packets, 0 bytes 5 minute rate 0 bps Queueing Output Queue: Conversation 41 Bandwidth remaining 50 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet --More--   Queueing Output Queue: Conversation 42 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 45 packets, 2909 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Output Queue: Conversation 43 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 19/905 (depth/total drops/no-buffer drops) 0/0/0 R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route             180.40.7.. 2 Trying 180.40.7.2 ... Open R2# R2# R2# R2#q [Connection to 180.40.7.2 closed by foreign host] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 21:02:31, FastEthernet0/0 [110/793] via 180.40.7.131, 21:02:31, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.129, 21:02:31, FastEthernet0/0 [110/783] via 180.40.7.131, 21:02:31, FastEthernet0/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 21:02:31, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.129, 21:02:32, FastEthernet0/0 [110/782] via 180.40.7.131, 21:02:32, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 21:02:32, FastEthernet0/0 --More--  O 180.40.7.0/27 [110/782] via 180.40.7.129, 21:02:33, FastEthernet0/0 O 180.40.7.64/27 [110/782] via 180.40.7.129, 21:02:33, FastEthernet0/0 [110/782] via 180.40.7.131, 21:02:33, FastEthernet0/0 R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int s 1/2 Serial1/2 Service-policy output: Prob9 Class-map: FTP (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp 0 packets, 0 bytes 5 minute rate 0 bps Match: access-group 103 0 packets, 0 bytes 5 minute rate 0 bps Queueing Output Queue: Conversation 41 Bandwidth remaining 50 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 17 packets, 791 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet --More--   Queueing Output Queue: Conversation 42 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 2/97 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 54 packets, 3695 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Output Queue: Conversation 43 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 19/905 (depth/total drops/no-buffer drops) 0/0/0 R3#sh pol int s 1/2180.40.7.2  21 Trying 180.40.7.2, 21 ... % Connection refused by remote host R3#180.40.7.2 2120   0 Trying 180.40.7.2, 20 ... % Connection refused by remote host R3#180.40.7.2 201sh pol int s 1/2 Serial1/2 Service-policy output: Prob9 Class-map: FTP (match-any) 1 packets, 48 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp 0 packets, 0 bytes 5 minute rate 0 bps Match: access-group 103 1 packets, 48 bytes 5 minute rate 0 bps Queueing Output Queue: Conversation 41 Bandwidth remaining 50 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 1/48 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 17 packets, 791 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet --More--   R3#sh run | b vcl   class class-map match-all Prec1 match precedence 1 class-map match-all Prec3 match precedence 3 class-map match-all Telnet match protocol telnet class-map match-any FTP match protocol ftp match access-group 103 ! ! policy-map test class Prec1 class Prec3 policy-map Prob9 class FTP bandwidth remaining percent 50 class Telnet bandwidth remaining percent 25 class class-default bandwidth remaining percent 25 ! ! --More--  ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 --More--   encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! --More--  interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server ! access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo-reply --More--  access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo-reply access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo-reply access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo access-list 103 permit tcp any any eq ftp-data access-list 103 permit tcp any eq ftp-data any queue-list 1 protocol ip 1 tcp ftp queue-list 1 protocol ip 1 tcp ftp-data queue-list 1 protocol ip 2 tcp telnet queue-list 1 default 3 queue-list 1 queue 1 byte-count 2673 queue-list 1 queue 2 byte-count 1309 queue-list 1 queue 3 byte-count 1294 ! route-map Prob1 permit 10 match ip address 102 match length 1001 2147483647 set interface Serial1/2 ! route-map Prob1 permit 20 match ip address 100 set ip next-hop 180.40.7.67 ! --More--   R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] *M R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 1 R7(config-if)#stan R7(config-if)#standby ? <0-255> group number authentication Authentication delay HSRP initialisation delay ip Enable HSRP and set the virtual IP address mac-address Virtual MAC address name Redundancy name string preempt Overthrow lower priority Active routers priority Priority level redirects Configure sending of ICMP Redirect messages with an HSRP virtual IP address as the gateway IP address timers Hello and hold timers track Priority tracking use-bia HSRP uses interface's burned in address R7(config-if)#standby 71 ip 180.40.7.132 R7(config-if)#do sh stand FastEthernet0/1 - Group 71 State is Listen Virtual IP address is 180.40.7.132 Active virtual MAC address is unknown Local virtual MAC address is 0000.0c07.ac47 (default) Hello time 3 sec, hold time 10 sec Preemption disabled Active router is unknown Standby router is unknown Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/1-71" (default) R7(config-if)# *Mar 1 21:48:35.331: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Standby -> Active R7(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#cpo  onmf  fign  t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s   f 0/0 R3(config-if)#standby 71 ip 180.40.7.132 R3(config-if)#standby 71 ip 180.40.7.132                 pri R3(config-if)#standby 71 priority 150 R3(config-if)#standby 71 priority 150              track ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing R3(config-if)#standby 71 track ser 1/2 R3(config-if)#standby 71 track ser 1/2 51 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)# R3(config-if)# R3(config-if)# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh run int fa 0/3 Building configuration... Current configuration : 95 bytes ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable end S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)# R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#shut R3(config-if)# *Mar 2 05:46:52.614: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 05:46:52.614: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from EXSTART to DOWN, Neighbor Down: Interface down or detached R3(config-if)#no shut *Mar 2 05:46:54.613: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 2 05:46:55.615: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R3(config-if)#no shut R3(config-if)# *Mar 2 05:46:58.548: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up R3(config-if)# *Mar 2 05:47:01.076: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up *Mar 2 05:47:02.077: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#no shut R3(config-if)# *Mar 2 05:47:07.634: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#no shutshut do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Speak unknown unknown 180.40.7.132 R3(config-if)# *Mar 2 05:47:29.014: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Active R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Active local 180.40.7.131 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Active local 180.40.7.131 180.40.7.132 R3(config-if)# *Mar 2 05:47:42.620: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 05:47:42.628: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Active local 180.40.7.131 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Active local 180.40.7.131 180.40.7.132 R3(config-if)# RACK11AS>z 5 [Resuming connection 5 to r5 ... ] 1d S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/3 S5(config-if)#sp S5(config-if)#sp  swi S5(config-if)#switchport mode acc S5(config-if)#span S5(config-if)#spanning-tree po S5(config-if)#spanning-tree portf S5(config-if)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/3 but will only have effect when the interface is in a non-trunking mode. S5(config-if)#^Z S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#shut R3(config-if)# *Mar 2 05:48:55.976: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Active -> Init R3(config-if)# *Mar 2 05:48:55.980: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 05:48:55.980: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)#noshut *Mar 2 05:48:57.975: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 2 05:48:58.977: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R3(config-if)#noshut shut R3(config-if)# *Mar 2 05:49:03.208: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 2 05:49:04.210: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3(config-if)# *Mar 2 05:49:05.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R3(config-if)# *Mar 2 05:49:07.042: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3(config-if)# *Mar 2 05:49:12.387: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 05:49:12.391: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3(config-if)#no shutshut do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand brino shut shut do sh stand brino shut shut do sh stand bristandby 71 track ser 1/2 51                pre R3(config-if)#standby 71 preempt R3(config-if)# R3(config-if)# *Mar 2 05:50:06.063: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Active R3(config-if)# R3(config-if)#^Z R3# *Mar 2 05:50:15.182: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#h shuy  R2(config-if)# *Mar 2 05:50:29.153: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] *nterface Serial1/2, changed state to down R3# R3# *Mar 2 05:50:27.662: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 05:50:28.664: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3#sh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 99 P Active local 180.40.7.131 180.40.7.132 R3# R3# R3# R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar 1 R7(config-if)#do sh standstandby 71 ip 180.40.7.132               pre R7(config-if)# *Mar 1 21:57:27.247: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Standby -> Active R7(config-if)#^Z R7#de *Mar 1 21:59:01.814: %SYS-5-CONFIG_I: Configured from console by console R7#deb ip arp? % Unrecognized command R7#deb ip arp      arp ? R7#deb arp   ARP packet debugging is on R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#log buff R7(config)#^Z R7# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Ma R2(config-if)#no shut R2(config-if)#^Z R2# RACK11AS>7 [Resuming connection 7 to r7 ... ] *M R7# R7# R7# *Mar 1 21:59:30.289: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Active -> Speak R7# *Mar 1 21:59:30.293: IP ARP: rcvd rep src 180.40.7.132 0000.0c07.ac47, dst 180.40.7.132 FastEthernet0/1 R7# *Mar 1 21:59:33.290: IP ARP: rcvd rep src 180.40.7.132 0000.0c07.ac47, dst 180.40.7.132 FastEthernet0/1 R7# *Mar 1 21:59:36.291: IP ARP: rcvd rep src 180.40.7.132 0000.0c07.ac47, dst 180.40.7.132 FastEthernet0/1 R7#u all All possible debugging has been turned off R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run int s 1/2 Building configuration... Current configuration : 123 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 end R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7# R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int fa 0? / R3#sh run int fa 0 0/07 ^ % Invalid input detected at '^' marker. R3#sh run int fa 0/07  Building configuration... Current configuration : 257 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 71 ip 180.40.7.132 standby 71 priority 150 standby 71 preempt standby 71 track Serial1/2 51 service-policy input test end R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int s   f 0/1 Building configuration... Current configuration : 176 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex standby 71 ip 180.40.7.132 standby 71 preempt service-policy output Prob6 end R7# R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#tra R3(config)#trac R3(config)#track ? <1-500> Tracked object resolution Tracking resolution parameters timer Polling interval timers R3(config)#track 1 ? interface Select an interface to track ip IP protocol R3(config)#track 1 ip ? route IP route R3(config)#track 1 ip rout ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R3(config)#track 1 ip rout 230  0.10.. 2.0/24 > ? metric Route metric reachability Route reachability state R3(config)#track 1 ip rout 20.10.2.0/24 re R3(config)#track 1 ip rout 20.10.2.0/24 reachability % Cannot change object created via HSRP R3(config)#track 1 ip rout 20.10.2.0/24 reachability  ? R3(config)#track 1 ip rout 20.10.2.0/24 reachability  ip rout 20.10.2.0/24 reachability 2 ip rout 20.10.2.0/24 reachability  R3(config-track)#do sh track Track 1 (via HSRP) Interface Serial1/2 line-protocol Line protocol is Up 3 changes, last change 00:04:39 Tracked by: HSRP FastEthernet0/0 71 Track 2 IP route 20.10.2.0 255.255.255.0 reachability Reachability is Up (OSPF) 1 change, last change 00:00:15 First-hop interface is Serial1/0 R3(config-track)#int fa 0/0 R3(config-if)#int fa 0/0do sh tracktrack 2 ip rout 20.10.2.0/24 reachability 1 ip rout 20.10.2.0/24 reachability standby 71 preempt         track 2 ? decrement Priority decrement R3(config-if)#standby 71 track 2 dec R3(config-if)#standby 71 track 2 decrement 61 R3(config-if)#^Z R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/1 S6(config-if)#sw S6(config-if)#switchport acc % Incomplete command. S6(config-if)#switchport acces % Incomplete command. S6(config-if)#switchport acces     mode acc Command rejected: Fa0/1 not a switching port. S6(config-if)#shut S6(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh stand FastEthernet0/0 - Group 71 State is Active 10 state changes, last state change 00:06:28 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac47 Local virtual MAC address is 0000.0c07.ac47 (default) Hello time 3 sec, hold time 10 sec Next hello sent in 1.854 secs Preemption enabled Active router is local Standby router is 180.40.7.131, priority 100 (expires in 9.748 sec) Priority 150 (configured 150) Track interface Serial1/2 state Up decrement 51 Track object 2 state Up decrement 61 IP redundancy name is "hsrp-Fa0/0-71" (default) R3#qsh stand bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 150 P Active local 180.40.7.131 180.40.7.132 R3#sh ip ospf *Mar 2 05:59:33.349: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Active -> Speak R3#sh ip ospf             R3# R3# R3# R3#sh stand bri  bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 71 89 P Standby 180.40.7.131 local 180.40.7.132 R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] 1d S6(config-if)#no shut S6(config-if)#^Z S6# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#deb ip ospf ? adj OSPF adjacency events database-timer OSPF database timer events OSPF events flood OSPF flooding hello OSPF hello events lsa-generation OSPF lsa generation mpls OSPF MPLS nsf OSPF non-stop forwarding events packet OSPF packets retransmission OSPF retransmission events spf OSPF spf tree OSPF database tree R3#deb ip ospf             sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:00:04, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.2, 00:00:04, Serial1/2 [110/792] via 180.40.7.67, 00:00:04, Serial1/0 O 20.10.1.0 [110/782] via 180.40.7.67, 00:00:04, Serial1/0 [110/782] via 180.40.7.2, 00:00:04, Serial1/2 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:04, FastEth *Mar 2 06:00:18.363: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Activeernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:00:05, Serial1/0 [110/781] via 180.40.7.2, 00:00:05, Serial1/2 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:00:05, FastEthernet0/0 --More--   R3#sh run | b track track 2 ip route 20.10.2.0 255.255.255.0 reachability ! ! ! class-map match-all Prec1 match precedence 1 class-map match-all Prec3 match precedence 3 class-map match-all Telnet match protocol telnet class-map match-any FTP match protocol ftp match access-group 103 ! ! policy-map test class Prec1 class Prec3 policy-map Prob9 class FTP bandwidth remaining percent 50 class Telnet bandwidth remaining percent 25 --More--   class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 71 ip 180.40.7.132 standby 71 priority 150 standby 71 preempt standby 71 track Serial1/2 51 standby 71 track 2 decrement 61 service-policy input test ! interface BRI0/0 no ip address shutdown --More--  ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#vr R3(config-if)#vrrp ? <1-255> Group number R3(config-if)#vrrp 71 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R3(config-if)#vrrp 71 ip ? A.B.C.D VRRP group IP address R3(config-if)#vrrp 71 ip 180.40.7.133 R3(config-if)# *Mar 2 06:03:02.404: %VRRP-6-STATECHANGE: Fa0/0 Grp 71 state Init -> Backup R3(config-if)# *Mar 2 06:03:06.014: %VRRP-6-STATECHANGE: Fa0/0 Grp 71 state Backup -> Master R3(config-if)#vrrp 71 ip 180.40.7.133               pri R3(config-if)#vrrp 71 priority 111 R3(config-if)# RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#vrrp 71 ip 180.04.   40.7.133 R7(config-if)# *Mar 1 22:10:21.660: %VRRP-6-STATECHANGE: Fa0/1 Grp 71 state Init -> Backup R7(config-if)#^Z R7# *Mar 1 22:10:24.337: %SYS-5-CONFIG_I: Configured from console by console R7#sh vrrp brie Interface Grp Pri Time Own Pre State Master addr Group addr Fa0/1 71 100 3609 Y Backup 180.40.7.129 180.40.7.133 R7#\  R7# R7# R7#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/1 71 100 P Standby 180.40.7.129 local 180.40.7.132 R7#sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 - 0012.7f8e.c6c1 ARPA FastEthernet0/1 Internet 180.40.7.130 135 0030.85f3.6f40 ARPA FastEthernet0/1 Internet 180.40.7.129 15 0012.7f8d.3ca0 ARPA FastEthernet0/1 Internet 208.28.1.1 - 0012.7f8e.c6c0 ARPA FastEthernet0/0 Internet 208.28.1.2 135 000c.301f.a400 ARPA FastEthernet0/0 R7# RACK11AS>4 [Resuming connection 4 to r4 ... ] *M R4#ping 180.40.7.133 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.133, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/12 ms R4#ping 180.40.7.133 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.132, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R4#sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 135 0012.7f8e.c6c1 ARPA FastEthernet0/0 Internet 180.40.7.130 - 0030.85f3.6f40 ARPA FastEthernet0/0 Internet 180.40.7.129 15 0012.7f8d.3ca0 ARPA FastEthernet0/0 R4# R4# R4# R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.131, 00:05:45, FastEthernet0/0 [110/793] via 180.40.7.129, 00:05:45, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.131, 00:05:45, FastEthernet0/0 [110/783] via 180.40.7.129, 00:05:45, FastEthernet0/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:05:45, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.131, 00:05:46, FastEthernet0/0 [110/782] via 180.40.7.129, 00:05:46, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:05:46, FastEthernet0/0 --More--  O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:05:50, FastEthernet0/0 O 180.40.7.64/27 [110/782] via 180.40.7.131, 00:05:50, FastEthernet0/0 [110/782] via 180.40.7.129, 00:05:50, FastEthernet0/0 R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa -0  0/0 R4(config-if)#exit R4(config)#no ip local pol rout Prob3 R4(config)#^Z R4#config tsh ip route *Mar 2 06:11:25.824: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip routearp ping 180.40.7.132 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.132, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/3/4 ms R4#ping 180.40.7.132config t sh ip routearp ping 180.40.7.1323 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.133, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/3/4 ms R4#ping 180.40.7.1332config t sh ip routearp  Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 139 0012.7f8e.c6c1 ARPA FastEthernet0/0 Internet 180.40.7.130 - 0030.85f3.6f40 ARPA FastEthernet0/0 Internet 180.40.7.129 20 0012.7f8d.3ca0 ARPA FastEthernet0/0 Internet 180.40.7.133 0 0000.5e00.0147 ARPA FastEthernet0/0 Internet 180.40.7.132 0 0000.0c07.ac47 ARPA FastEthernet0/0 R4# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#vrrp R3(config-if)#vrrp ? <1-255> Group number R3(config-if)#vrrp 71 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R3(config-if)#vrrp 71         ^Z R3#sh run *Mar 2 06:14:07.650: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int fa 0/1 Building configuration... Current configuration : 83 bytes ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto end R3#sh run int fa 0/1 0 Building configuration... Current configuration : 337 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 71 ip 180.40.7.133 vrrp 71 priority 111 standby 71 ip 180.40.7.132 standby 71 priority 150 standby 71 preempt standby 71 track Serial1/2 51 standby 71 track 2 decrement 61 service-policy input test end R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int fa 0/1 Building configuration... Current configuration : 201 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 71 ip 180.40.7.133 standby 71 ip 180.40.7.132 standby 71 preempt service-policy output Prob6 end R7# R7#^x3 % Unknown command or computer name, or unable to find computer address R7# R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip dhc R3(config)#ip dhcp ex R3(config)#ip dhcp excluded-address ? A.B.C.D Low IP address R3(config)#ip dhcp excluded-address 180.40.7.129 R3(config)#ip dhcp excluded-address 180.40.7.129  31 180.40.7.133 4 R3(config)#ip dhc R3(config)#ip dhcp po R3(config)#ip dhcp pool Prob13 R3(dhcp-config)#net R3(dhcp-config)#netw R3(dhcp-config)#network 180.40.7.128 ? /nn or A.B.C.D Network mask or prefix length R3(dhcp-config)#network 180.40.7.128 /1 27 R3(dhcp-config)#def R3(dhcp-config)#default-router 180.40.7.132 180.40.7.133 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#dns R3(dhcp-config)#dns-server 208.28..821.82 R3(dhcp-config)#dns-server 208.28.1.82 ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#dns-server 208.28.1.82                        dom R3(dhcp-config)#domain-name > ccie.com R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   utilization Configure various utilization parameters vrf Associate this pool with a VRF R3(dhcp-config)#op R3(dhcp-config)#option 150 ? ascii Data is an NVT ASCII string hex Data is a hexadecimal string instance Specify the option instance ip Data is one or more IP addresses R3(dhcp-config)#option 150 ip : ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#option 150 ip 20.20.2020  .20 R3(dhcp-config)#ex1it ^ % Invalid input detected at '^' marker. R3(dhcp-config)#exit R3(config)#ip dch  jcp   j hcp pool ForR4 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#host ? A.B.C.D IP address in dotted-decimal notation R3(dhcp-config)#host 180.40.7.130 R3(dhcp-config)#host 180.40.7.130 /27 R3(dhcp-config)#do sh ru  n | b ip dhcp % Ambiguous command: "do sh run | b ip dhcp" R3(config)#do sh run | b ip dhcp ip dhcp excluded-address 180.40.7.129 ip dhcp excluded-address 180.40.7.131 180.40.7.134 ! ip dhcp pool Prob13 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 180.40.7.133 dns-server 208.28.1.82 domain-name ccie.com option 150 ip 20.20.20.20 ! ip dhcp pool ForR4 host 180.40.7.130 255.255.255.224 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! ! ! ! ! --More--   R3(config)#do sh run | b ip dhcphost 180.40.7.130 /27 ip dhcp pool ForR4 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#hardware-address ? WORD Dotted-hexadecimal string (aabb.ccdd.eeff ...) R3(dhcp-config)#hardware-address RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh int fa 0/0 FastEthernet0/0 is up, line protocol is up Hardware is AmdFE, address is 0030.85f3.6f40 (bia 0030.85f3.6f40) Internet address is 180.40.7.130/27 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:04, output 00:00:03, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 28659 packets input, 3165123 bytes Received 28533 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 24421 packets output, 2474530 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets --More-- RACK11AS>3 [Resuming connection 3 to r3 ... ] 0030.85f3.6f40 R3(dhcp-config)#hardware-address 0030.85f3.6f40 ^Z R3# *Mar 2 06:24:14.068: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>4 [Resuming connection 4 to r4 ... ]   0 babbles, 0 late collision, 0 deferred --More--   R4#configt Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#ip add dhcp R4(config-if)# *Mar 2 06:27:01.568: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from 2WAY to DOWN, Neighbor Down: Interface down or detached *Mar 2 06:27:01.568: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)# *Mar 2 06:27:12.740: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.135, mask 255.255.255.224, hostname R4 R4(config-if)# *Mar 2 06:27:19.188: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)#^Z R4# RACK11AS>4 3 [Resuming connection 3 to r3 ... ] *M R3#sh ip dhcp d bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 0030.85f3.6f40 Infinite Manual 180.40.7.135 0063.6973.636f.2d30. Mar 03 1993 06:24 AM Automatic 3033.302e.3835.6633. 2e36.6634.302d.4661. 302f.30 R3#clea ip dhcp bin * R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0.1  /0 R4(config-if)#int fa 0/0p add dhcp ? client-id Specify client-id to use hostname Specify value for hostname option R4(config-if)#ip add dhcp cli ? FastEthernet FastEthernet IEEE 802.3 R4(config-if)#ip add dhcp cli fa ? <0-6> FastEthernet interface number R4(config-if)#ip add dhcp cli fa 0/0 ? hostname Specify value for hostname option R4(config-if)#ip add dhcp cli fa 0/0 R4(config-if)# *Mar 2 06:28:40.092: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 06:28:40.096: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#^Z R4# *Mar 2 06:28:45.240: %SYS-5-CONFIG_I: Configured from console by console R4# *Mar 2 06:28:46.264: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.136, mask 255.255.255.224, hostname R4 R4# R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#clea ip dhcp bin *sh ip dhcp bin  Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 0030.85f3.6f40 Infinite Manual 180.40.7.136 0100.3085.f36f.40 Mar 03 1993 06:26 AM Automatic R3# *Mar 2 06:26:39.915: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#deb ip dhcp ? server DHCP server activity R4#deb ip dhcp       *Mar 2 06:29:25.164: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#deb ip    dhcp ? detail DHCP packet content R4#deb dhcp det *Mar 2 06:29:30.160: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#deb dhcp det DHCP client activity debugging is on (detailed) R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/09  R4(config-if)# RACK11AS>6 [Resuming connection 6 to r6 ... ] 1d0 S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/4 S6(config-if)#sw S6(config-if)#switchport mod S6(config-if)#switchport mode acc S6(config-if)#spa S6(config-if)#spanning-tree por S6(config-if)#spanning-tree portf S6(config-if)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/4 but will only have effect when the interface is in a non-trunking mode. S6(config-if)#^Z S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4(config-if)#shut *Mar 2 06:30:23.312: DHCP: SRelease attempt # 1 for entry: *Mar 2 06:30:23.312: Temp IP addr: 180.40.7.136 for peer on Interface: FastEthernet0/0 *Mar 2 06:30:23.312: Temp sub net mask: 255.255.255.224 *Mar 2 06:30:23.312: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:30:23.312: DHCP transaction id: 68A432C *Mar 2 06:30:23.312: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:30:23.312: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:30:23.316: Next timer fires after: 00:00:01 *Mar 2 06:30:23.316: Retry count: 1 Client-ID: 0030.85f3.6f40 *Mar 2 06:30:23.316: Hostname: R4 *Mar 2 06:30:23.316: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:30:23.316: DHCP: SRelease: 259 bytes *Mar 2 06:30:23.380: DHCP: SRelease attempt # 2 for entry: *Mar 2 06:30:23.380: Temp IP addr: 180.40.7.136 for peer on Interface: FastEthernet0/0 *Mar 2 06:30:23.380: Temp sub net mask: 255.255.255.224 *Mar 2 06:30:23.380: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:30:23.380: DHCP transaction id: 68A432C *Mar 2 06:30:23.380: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:30:23.380: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:30:23.380: Next timer fires after: 00:00:00 *Mar 2 06:30:23.380: Retry count: 2 Client-ID: 0030.85f3.6f40 *Mar 2 06:30:23.380: Hostname: R4 *Mar 2 06:30:23.384: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:30:23.384: DHCP: SRelease: 259 bytes *Mar 2 06:30:23.384: DHCP: Releasing ipl options: *Mar 2 06:30:23.384: Clearing default gateway and route to 180.40.7.132 *Mar 2 06:30:23.384: Removing old default route 180.40.7.132 *Mar 2 06:30:23.388: Clearing DNS address 208.28.1.82 *Mar 2 06:30:23.388: Clearing default domain of ccie.c R4(config-if)#om *Mar 2 06:30:24.312: DHCP: SRelease attempt # 3 for entry: *Mar 2 06:30:24.312: Temp IP addr: 180.40.7.136 for peer on Interface: FastEthernet0/0 *Mar 2 06:30:24.312: Temp sub net mask: 255.255.255.224 *Mar 2 06:30:24.312: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:30:24.312: DHCP transaction id: 68A432C *Mar 2 06:30:24.312: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:30:24.312: Next timer fires after: 00:00:01 *Mar 2 06:30:24.312: Retry count: 3 Client-ID: 0030.85f3.6f40 *Mar 2 06:30:24.312: Hostname: R4 *Mar 2 06:30:24.312: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:30:24.316: DHCP: SRelease: 259 bytes *Mar 2 06:30:25.388: RAC: DHCP stopped on interface FastEthernet0/0 R4(config-if)# *Mar 2 06:30:25.388: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 06:30:25.388: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#no shut R4(config-if)# *Mar 2 06:30:27.392: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 2 06:30:28.392: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R4(config-if)# *Mar 2 06:30:29.020: DHCP: DHCP client process started: 10 *Mar 2 06:30:29.020: RAC: Delaying starting DHCP because interface FastEthernet0/0 not up R4(config-if)# *Mar 2 06:30:31.008: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up R4(config-if)# *Mar 2 06:30:33.580: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up *Mar 2 06:30:33.580: DHCP: DHCP client process started: 10 *Mar 2 06:30:33.584: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 06:30:33.584: DHCP: Try 1 to acquire address for FastEthernet0/0 *Mar 2 06:30:33.600: DHCP: allocate request *Mar 2 06:30:33.600: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 06:30:33.600: DHCP: new entry. add to queue *Mar 2 06:30:33.600: DHCP: SDiscover attempt # 1 for entry: *Mar 2 06:30:33.600: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 06:30:33.600: Temp sub net mask: 0.0.0.0 *Mar 2 06:30:33.600: DHCP Lease server: 0.0.0.0, state: 1 Selecting R4(config-if)# *Mar 2 06:30:33.600: DHCP transaction id: 68C048A *Mar 2 06:30:33.600: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 06:30:33.600: Next timer fires after: 00:00:03 *Mar 2 06:30:33.604: Retry count: 1 Client-ID: 0030.85f3.6f40 *Mar 2 06:30:33.604: Hostname: R4 *Mar 2 06:30:33.604: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 06:30:33.604: DHCP: SDiscover 274 bytes *Mar 2 06:30:33.604: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4(config-if)# *Mar 2 06:30:35.612: DHCP: Received a BOOTREP pkt *Mar 2 06:30:35.612: DHCP: Scan: Message type: DHCP Offer *Mar 2 06:30:35.612: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 06:30:35.612: DHCP: Scan: Lease Time: 86400 *Mar 2 06:30:35.612: DHCP: Scan: Renewal time: 43200 *Mar 2 06:30:35.612: DHCP: Scan: Rebind time: 75600 *Mar 2 06:30:35.612: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 06:30:35.616: DHCP: Scan: Router Option: 180.40.7.132, 180.40.7.133 *Mar 2 06:30:35.616: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 06:30:35.616: DHCP: Scan: Domain Name: ccie.com *Mar 2 06:30:35.616: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 06:30:35.616: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 06:30:35.616: UDP sport: 43, dport: 44, length: 314 *Mar 2 06:30:35.616: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 06:30:35.616: DHCP server identifier: 180.40.7.129 *Mar R4(config-if)#2 06:30:35.616: xid: 68C048A, secs: 0, flags: 8000 *Mar 2 06:30:35.616: client: 0.0.0.0, your: 180.40.7.137 *Mar 2 06:30:35.616: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 06:30:35.620: options block length: 66 *Mar 2 06:30:35.620: DHCP Offer Message Offered Address: 180.40.7.137 *Mar 2 06:30:35.620: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 06:30:35.620: DHCP: Server ID Option: 180.40.7.129 *Mar 2 06:30:35.620: DHCP: offer received from 180.40.7.129 *Mar 2 06:30:35.620: DHCP: SRequest attempt # 1 for entry: *Mar 2 06:30:35.620: Temp IP addr: 180.40.7.137 for peer on Interface: FastEthernet0/0 *Mar 2 06:30:35.620: Temp sub net mask: 255.255.255.224 *Mar 2 06:30:35.620: DHCP Lease server: 180.40.7.129, state: 2 Requesting *Mar 2 06:30:35.620: DHCP transaction id: 68C048A *Mar 2 06:30:35.620: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 06:30:35.624: Next timer fires after: 00:00:01 *Mar 2 06:30:35.624: Retry count: 1 Client-ID: 0030.85f3.6f40 *Mar 2 06:30:35.624: Hostname: R4 *Mar 2 06:30:35.624: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 06:30:35.624: DHCP: SRequest- Requested IP addr option: 180.40.7.137 *Mar 2 06:30:35.624: DHCP: SRequest placed lease len option: 86400 *Mar 2 06:30:35.624: DHCP: SRequest: 292 bytes *Mar 2 06:30:35.624: DHCP: SRequest: 292 bytes *Mar 2 06:30:35.628: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 06:30:35.632: DHCP: Received a BOOTREP pkt *Mar 2 06:30:35.632: DHCP: Scan: Message type: DHCP Ack *Mar 2 06:30:35.632: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 06:30:35.632: DHCP: Scan: Lease Time: 86400 *Mar 2 06:30:35.632: DHCP: Scan: Renewal time: 43200 *Mar 2 06:30:35.632: DHCP: Scan: Rebind time: 75600 *Mar 2 06:30:35.636: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 06:30:35.636: DHCP: Scan: Router Option: 180.40.7.132, 180.40.7.133 *Mar 2 06:30:35.636: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 06:30:35.636: DHCP: Scan: Domain Name: ccie.com *Mar 2 06:30:35.636: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 06:30:35.636: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 06:30:35.636: UDP sport: 43, dport: 44, length: 314 *Mar 2 06:30:35.636: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 06:30:35.636: DHCP server identifier: 180.40.7.129 *Mar 2 06:30:35.636: xid: 68C048A, secs: 0, flags: 8000 *Mar 2 06:30:35.636: client: 0.0.0.0, your: 180.40.7.137 *Mar 2 06:30:35.640: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 06:30:35.640: options block length: 66 *Mar 2 06:30:35.640: DHCP Ack Message *Mar 2 06:30:35.640: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 06:30:35.640: DHCP: Server ID Option: 180.40.7.129 *Mar 2 06:30:38.648: DHCP: Releasing ipl options: *Mar 2 06:30:38.648: DHCP: Applying DHCP options: *Mar 2 06:30:38.652: Setting default_gateway to 180.40.7.132 *Mar 2 06:30:38.652: Adding default route 180.40.7.132 *Mar 2 06:30:39.652: Adding DNS server address 208.28.1.82 *Mar 2 06:30:39.652: Setting default domain to ccie.com *Mar 2 06:30:39.652: DHCP Client Pooling: ***Allocated IP address: 180.40.7.137 *Mar 2 06:30:39.748: Allocated IP address = 180.40.7.137 255.255.255.224 *Mar 2 06:30:39.748: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.137, mask 255.255.255.224, hostname R4 R4(config-if)# R4(config-if)# *Mar 2 06:30:55.312: DHCP: QScan: Purging entry *Mar 2 06:30:55.312: DHCP: deleting entry 63050880 0.0.0.0 from list *Mar 2 06:30:55.312: Temp IP addr: 0.0.0.0 for peer on Interface: unknown *Mar 2 06:30:55.312: Temp sub net mask: 255.255.255.224 *Mar 2 06:30:55.312: DHCP Lease server: 180.40.7.129, state: 8 Purging *Mar 2 06:30:55.312: DHCP transaction id: 68A432C *Mar 2 06:30:55.312: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:30:55.312: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:30:55.312: No timer running *Mar 2 06:30:55.312: Retry count: 0 Client-ID: *Mar 2 06:30:55.312: Hostname: R4 R4(config-if)# *Mar 2 06:31:18.668: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)# *Mar 2 06:31:23.664: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)#^Z R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip dhcp bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 0030.85f3.6f40 Infinite Manual 180.40.7.137 0100.3085.f36f.40 Mar 03 1993 06:28 AM Automatic R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int    h hardware-address 0030.85f3.6f40ip dhcp pool ForR4 do sh run | b ip dhcpip dhcp pool ForR4  R3(dhcp-config)#ip dhcp pool ForR4hardware-address 0030.85f3.6f40    ip dhcp pool ForR4 hardware-address 0030.85f3.6f40nhardware-address 0030.85f3.6f40ohardware-address 0030.85f3.6f40 hardware-address 0030.85f3.6f40 R3(dhcp-config)#cl R3(dhcp-config)#client-i R3(dhcp-config)#client-identifier 0100.3085.f36f.40 R3(dhcp-config)#^Z R3#config tsh ip dhcp binclea ip dhcp bin * *Mar 2 06:29:52.759: %SYS-5-CONFIG_I: Configured from console by console R3#clea ip dhcp bin * R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#shut *Mar 2 06:32:34.444: DHCP: SRelease attempt # 1 for entry: *Mar 2 06:32:34.444: Temp IP addr: 180.40.7.137 for peer on Interface: FastEthernet0/0 *Mar 2 06:32:34.444: Temp sub net mask: 255.255.255.224 *Mar 2 06:32:34.448: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:32:34.448: DHCP transaction id: 68C048A *Mar 2 06:32:34.448: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:32:34.448: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:32:34.448: Next timer fires after: 00:00:00 *Mar 2 06:32:34.448: Retry count: 1 Client-ID: 0030.85f3.6f40 *Mar 2 06:32:34.448: Hostname: R4 *Mar 2 06:32:34.448: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:32:34.448: DHCP: SRelease: 259 bytes *Mar 2 06:32:34.516: DHCP: SRelease attempt # 2 for entry: *Mar 2 06:32:34.516: Temp IP addr: 180.40.7.137 for peer on Interface: FastEthernet0/0 *Mar 2 06:32:34.516: Temp sub net mask: 255.255.255.224 *Mar 2 06:32:34.516: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:32:34.516: DHCP transaction id: 68C048A *Mar 2 06:32:34.516: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:32:34.516: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:32:34.516: Next timer fires after: 00:00:00 *Mar 2 06:32:34.516: Retry count: 2 Client-ID: 0030.85f3.6f40 *Mar 2 06:32:34.516: Hostname: R4 *Mar 2 06:32:34.520: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:32:34.520: DHCP: SRelease: 259 bytes *Mar 2 06:32:34.520: DHCP: Releasing ipl options: *Mar 2 06:32:34.520: Clearing default gateway and route to 180.40.7.132 *Mar 2 06:32:34.520: Removing old default route 180.40.7.132 *Mar 2 06:32:34.524: Clearing DNS address 208.28.1.82 *Mar 2 06:32:34.524: Clearing default domain of ccie.c R4(config-if)#no shut R4(config-if)#om *Mar 2 06:32:35.444: DHCP: SRelease attempt # 3 for entry: *Mar 2 06:32:35.444: Temp IP addr: 180.40.7.137 for peer on Interface: FastEthernet0/0 *Mar 2 06:32:35.444: Temp sub net mask: 255.255.255.224 *Mar 2 06:32:35.444: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:32:35.444: DHCP transaction id: 68C048A *Mar 2 06:32:35.444: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:32:35.444: Next timer fires after: 00:00:01 *Mar 2 06:32:35.444: Retry count: 3 Client-ID: 0030.85f3.6f40 *Mar 2 06:32:35.444: Hostname: R4 *Mar 2 06:32:35.444: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:32:35.448: DHCP: SRelease: 259 bytes *Mar 2 06:32:36.524: RAC: DHCP stopped on interface FastEthernet0/0 *Mar 2 06:32:36.524: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 06:32:36.524: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 06:32:36.564: DHCP: DHCP client process started: 10 *Mar 2 06:32:36.564: RAC: Delaying starting DHCP because interface FastEthernet0/0 not up R4(config-if)# R4(config-if)# *Mar 2 06:32:39.528: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R4(config-if)# R4(config-if)# R4(config-if)# R4(config-if)# *Mar 2 06:32:49.024: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up *Mar 2 06:32:49.024: DHCP: DHCP client process started: 10 *Mar 2 06:32:49.028: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 06:32:49.028: DHCP: Try 1 to acquire address for FastEthernet0/0 *Mar 2 06:32:49.040: DHCP: allocate request *Mar 2 06:32:49.044: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 06:32:49.044: DHCP: new entry. add to queue *Mar 2 06:32:49.044: DHCP: SDiscover attempt # 1 for entry: *Mar 2 06:32:49.044: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 06:32:49.044: Temp sub net mask: 0.0.0.0 *Mar 2 06:32:49.044: DHCP Lease server: 0.0.0.0, state: 1 Selecting *Mar 2 06:32:49.044: DHCP transaction id: 68E1AA9 *Mar 2 06:32:49.044: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 06:32:49.044: Next timer fires after: 00:00:03 *Mar 2 06:32:49.044: Retry count: 1 Client-ID R4(config-if)#: 0030.85f3.6f40 *Mar 2 06:32:49.048: Hostname: R4 *Mar 2 06:32:49.048: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 06:32:49.048: DHCP: SDiscover 274 bytes *Mar 2 06:32:49.048: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 06:32:49.052: DHCP: Received a BOOTREP pkt *Mar 2 06:32:49.056: DHCP: Scan: Message type: DHCP Offer *Mar 2 06:32:49.056: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 06:32:49.056: DHCP: Scan: Lease Time: 86400 *Mar 2 06:32:49.056: DHCP: Scan: Renewal time: 43200 *Mar 2 06:32:49.056: DHCP: Scan: Rebind time: 75600 *Mar 2 06:32:49.056: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 06:32:49.056: DHCP: Scan: Router Option: 180.40.7.132, 180.40.7.133 *Mar 2 06:32:49.056: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 06:32:49.056: DHCP: Scan: Domain Name: ccie.com *Mar 2 06:32:49.056: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 06:32:49.056: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 06:32:49.060: UDP sport: 43, dport: 44, length: 314 *Mar 2 06:32:49.060: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 06:32:49.060: DHCP server identifier: 180.40.7.129 *Mar 2 06:32:49.060: xid: 68E1AA9, secs: 0, flags: 8000 *Mar 2 06:32:49.060: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 06:32:49.060: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 06:32:49.060: options block length: 66 *Mar 2 06:32:49.060: DHCP Offer Message Offered Address: 180.40.7.130 *Mar 2 06:32:49.060: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 06:32:49.060: DHCP: Server ID Option: 180.40.7.129 *Mar 2 06:32:49.060: DHCP: offer received from 180.40.7.129 *Mar 2 06:32:49.064: DHCP: SRequest attempt # 1 for entry: *Mar 2 06:32:49.064: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 06:32:49.064: Temp sub net mask: 255.255.255.224 *Mar 2 06:32:49.064: DHCP Lease server: 180.40.7.129, state: 2 Requesting *Mar 2 06:32:49.064: DHCP transaction id: 68E1AA9 *Mar 2 06:32:49.064: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 06:32:49.064: Next timer fires after: 00:00:02 *Mar 2 06:32:49.064: Retry count: 1 Client-ID: 0030.85f3.6f40 *Mar 2 06:32:49.064: Hostname: R4 *Mar 2 06:32:49.064: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 06:32:49.064: DHCP: SRequest- Requested IP addr option: 180.40.7.130 *Mar 2 06:32:49.068: DHCP: SRequest placed lease len option: 86400 *Mar 2 06:32:49.068: DHCP: SRequest: 292 bytes *Mar 2 06:32:49.068: DHCP: SRequest: 292 bytes *Mar 2 06:32:49.068: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 06:32:49.072: DHCP: Received a BOOTREP pkt *Mar 2 06:32:49.076: DHCP: Scan: Message type: DHCP Ack *Mar 2 06:32:49.076: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 06:32:49.076: DHCP: Scan: Lease Time: 86400 *Mar 2 06:32:49.076: DHCP: Scan: Renewal time: 43200 *Mar 2 06:32:49.076: DHCP: Scan: Rebind time: 75600 *Mar 2 06:32:49.076: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 06:32:49.076: DHCP: Scan: Router Option: 180.40.7.132, 180.40.7.133 *Mar 2 06:32:49.076: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 06:32:49.076: DHCP: Scan: Domain Name: ccie.com *Mar 2 06:32:49.076: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 06:32:49.076: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 06:32:49.080: UDP sport: 43, dport: 44, length: 314 *Mar 2 06:32:49.080: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 06:32:49.080: DHCP server identifier: 180.40.7.129 *Mar 2 06:32:49.080: xid: 68E1AA9, secs: 0, flags: 8000 *Mar 2 06:32:49.080: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 06:32:49.080: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 06:32:49.080: options block length: 66 *Mar 2 06:32:49.080: DHCP Ack Message *Mar 2 06:32:49.080: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 06:32:49.080: DHCP: Server ID Option: 180.40.7.129 *Mar 2 06:32:52.092: DHCP: Releasing ipl options: *Mar 2 06:32:52.092: DHCP: Applying DHCP options: *Mar 2 06:32:52.096: Setting default_gateway to 180.40.7.132 *Mar 2 06:32:52.096: Adding default route 180.40.7.132 *Mar 2 06:32:53.096: Adding DNS server address 208.28.1.82 *Mar 2 06:32:53.096: Setting default domain to ccie.com *Mar 2 06:32:53.096: DHCP Client Pooling: ***Allocated IP address: 180.40.7.130 *Mar 2 06:32:53.144: Allocated IP address = 180.40.7.130 255.255.255.224 *Mar 2 06:32:53.144: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.224, hostname R4 R4(config-if)# R4(config-if)# *Mar 2 06:33:06.444: DHCP: QScan: Purging entry *Mar 2 06:33:06.444: DHCP: deleting entry 6223A794 0.0.0.0 from list *Mar 2 06:33:06.444: Temp IP addr: 0.0.0.0 for peer on Interface: unknown *Mar 2 06:33:06.444: Temp sub net mask: 255.255.255.224 *Mar 2 06:33:06.444: DHCP Lease server: 180.40.7.129, state: 8 Purging *Mar 2 06:33:06.444: DHCP transaction id: 68C048A *Mar 2 06:33:06.444: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:33:06.444: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:33:06.444: No timer running *Mar 2 06:33:06.444: Retry count: 0 Client-ID: *Mar 2 06:33:06.444: Hostname: R4 R4(config-if)#u all ^ % Invalid input detected at '^' marker. R4(config-if)#^Z R4#u all All possible debugging has been turned off R4# *Mar 2 06:33:20.868: %SYS-5-CONFIG_I: Configured from console by console R4# *Mar 2 06:33:32.112: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#xcon    config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int    *Mar 2 06:33:37.108: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config)#do deb dhcp de DHCP client activity debugging is on (detailed) R4(config)#int fa 0/0 R4(config-if)#int fa 0/0do deb dhcp deu all no shutshut int fa 0/0no shut shut int fa 0/0p add dhcp cli fa 0/0             *Mar 2 06:33:53.956: DHCP: SRelease attempt # 1 for entry: *Mar 2 06:33:53.956: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 06:33:53.956: Temp sub net mask: 255.255.255.224 *Mar 2 06:33:53.956: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:33:53.956: DHCP transaction id: 68E1AA9 *Mar 2 06:33:53.956: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:33:53.960: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:33:53.960: Next timer fires after: 00:00:00 *Mar 2 06:33:53.960: Retry count: 1 Client-ID: 0030.85f3.6f40 *Mar 2 06:33:53.960: Hostname: R4 *Mar 2 06:33:53.960: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:33:53.960: DHCP: SRelease: 259 bytes *Mar 2 06:33:54.024: DHCP: SRelease attempt # 2 for entry: *Mar 2 06:33:54.024: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 06:33:54.024: Temp sub net mask: 255.255.255.224 *Mar 2 06:33:54.024: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:33:54.024: DHCP transaction id: 68E1AA9 *Mar 2 06:33:54.024: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:33:54.024: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:33:54.024: Next timer fires after: 00:00:00 *Mar 2 06:33:54.024: Retry count: 2 Client-ID: 0030.85f3.6f40 *Mar 2 06:33:54.024: Hostname: R4 *Mar 2 06:33:54.028: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:33:54.028: DHCP: SRelease: 259 bytes *Mar 2 06:33:54.028: DHCP: Releasing ipl options: *Mar 2 06:33:54.028: Clearing default gateway and route to 180.40.7.132 *Mar 2 06:33:54.028: Removing old default route 180.40.7.132 *Mar 2 06:33:54.032: Clearing DNS address 208.28.1.82 *Mar 2 06:33:54.032: Clearing default domain of ccie.c R4(config-if)#om *Mar 2 06:33:54.956: DHCP: SRelease attempt # 3 for entry: *Mar 2 06:33:54.956: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 06:33:54.956: Temp sub net mask: 255.255.255.224 *Mar 2 06:33:54.956: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:33:54.956: DHCP transaction id: 68E1AA9 *Mar 2 06:33:54.956: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:33:54.956: Next timer fires after: 00:00:01 *Mar 2 06:33:54.956: Retry count: 3 Client-ID: 0030.85f3.6f40 *Mar 2 06:33:54.956: Hostname: R4 *Mar 2 06:33:54.956: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:33:54.960: DHCP: SRelease: 259 bytes *Mar 2 06:33:56.032: RAC: DHCP stopped on interface FastEthernet0/0 *Mar 2 06:33:56.032: DHCP: DHCP client process started: 10 *Mar 2 06:33:56.032: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 06:33:56.032: DHCP: Try 1 to acquire address for FastEthernet0/0 *Mar 2 06:33:56.036: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 06:33:56.036: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 06:33:56.060: DHCP: allocate request *Mar 2 06:33:56.064: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 06:33:56.064: DHCP: new entry. add to queue *Mar 2 06:33:56.064: DHCP: SDiscover attempt # 1 for entry: *Mar 2 06:33:56.064: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 06:33:56.064: Temp sub net mask: 0.0.0.0 *Mar 2 06:33:56.064: DHCP Lease server: 0.0.0.0, state: 1 Selecting *Mar 2 06:33:56.064: DHCP transaction id: 68F105C *Mar 2 06:33:56.064: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 06:33:56.064: Next timer fires after: 00:00:03 *Mar 2 06:33:56.064: Retry count: 1 Client-ID: cisco-0030.85f3.6f40-Fa0/0 *Mar 2 06:33:56.068: Hostname: R4 *Mar 2 06:33:56.068: DHCP: SDiscover: sending 294 byte length DHCP packet *Mar 2 06:33:56.068: DHCP: SDiscover 294 bytes *Mar 2 06:33:56.068: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 06:33:58.076: DHCP: Received a BOOTREP pkt *Mar 2 06:33:58.076: DHCP: Scan: Message type: DHCP Offer *Mar 2 06:33:58.076: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 06:33:58.076: DHCP: Scan: Lease Time: 86400 *Mar 2 06:33:58.076: DHCP: Scan: Renewal time: 43200 *Mar 2 06:33:58.076: DHCP: Scan: Rebind time: 75600 *Mar 2 06:33:58.076: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 06:33:58.080: DHCP: Scan: Router Option: 180.40.7.132, 180.40.7.133 *Mar 2 06:33:58.080: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 06:33:58.080: DHCP: Scan: Domain Name: ccie.com *Mar 2 06:33:58.080: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 06:33:58.080: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 06:33:58.080: UDP sport: 43, dport: 44, length: 314 *Mar 2 06:33:58.080: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 06:33:58.080: DHCP server identifier: 180.40.7.129 *Mar 2 06:33:58.080: xid: 68F105C, secs: 0, flags: 8000 *Mar 2 06:33:58.080: client: 0.0.0.0, your: 180.40.7.138 *Mar 2 06:33:58.084: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 06:33:58.084: options block length: 66 *Mar 2 06:33:58.084: DHCP Offer Message Offered Address: 180.40.7.138 *Mar 2 06:33:58.084: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 06:33:58.084: DHCP: Server ID Option: 180.40.7.129 *Mar 2 06:33:58.084: DHCP: offer received from 180.40.7.129 *Mar 2 06:33:58.084: DHCP: SRequest attempt # 1 for entry: *Mar 2 06:33:58.084: Temp IP addr: 180.40.7.138 for peer on Interface: FastEthernet0/0 *Mar 2 06:33:58.084: Temp sub net mask: 255.255.255.224 *Mar 2 06:33:58.084: DHCP Lease server: 180.40.7.129, state: 2 Requesting *Mar 2 06:33:58.084: DHCP transaction id: 68F105C *Mar 2 06:33:58.088: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 06:33:58.088: Next timer fires after: 00:00:01 *Mar 2 06:33:58.088: Retry count: 1 Client-ID: cisco-0030.85f3.6f40-Fa0/0 *Mar 2 06:33:58.088: Hostname: R4 *Mar 2 06:33:58.088: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 06:33:58.088: DHCP: SRequest- Requested IP addr option: 180.40.7.138 *Mar 2 06:33:58.088: DHCP: SRequest placed lease len option: 86400 *Mar 2 06:33:58.088: DHCP: SRequest: 312 bytes *Mar 2 06:33:58.088: DHCP: SRequest: 312 bytes *Mar 2 06:33:58.092: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 06:33:58.096: DHCP: Received a BOOTREP pkt *Mar 2 06:33:58.096: DHCP: Scan: Message type: DHCP Ack *Mar 2 06:33:58.096: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 06:33:58.096: DHCP: Scan: Lease Time: 86400 *Mar 2 06:33:58.096: DHCP: Scan: Renewal time: 43200 *Mar 2 06:33:58.100: DHCP: Scan: Rebind time: 75600 *Mar 2 06:33:58.100: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 06:33:58.100: DHCP: Scan: Router Option: 180.40.7.132, 180.40.7.133 *Mar 2 06:33:58.100: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 06:33:58.100: DHCP: Scan: Domain Name: ccie.com *Mar 2 06:33:58.100: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 06:33:58.100: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 06:33:58.100: UDP sport: 43, dport: 44, length: 314 *Mar 2 06:33:58.100: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 06:33:58.100: DHCP server identifier: 180.40.7.129 *Mar 2 06:33:58.100: xid: 68F105C, secs: 0, flags: 8000 *Mar 2 06:33:58.104: client: 0.0.0.0, your: 180.40.7.138 *Mar 2 06:33:58.104: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 06:33:58.104: options block length: 66 *Mar 2 06:33:58.104: DHCP Ack Message *Mar 2 06:33:58.104: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 06:33:58.104: DHCP: Server ID Option: 180.40.7.129 *Mar 2 06:34:01.112: DHCP: Releasing ipl options: *Mar 2 06:34:01.116: DHCP: Applying DHCP options: *Mar 2 06:34:01.116: Setting default_gateway to 180.40.7.132 *Mar 2 06:34:01.116: Adding default route 180.40.7.132 *Mar 2 06:34:02.116: Adding DNS server address 208.28.1.82 *Mar 2 06:34:02.116: Setting default domain to ccie.com *Mar 2 06:34:02.116: DHCP Client Pooling: ***Allocated IP address: 180.40.7.138 *Mar 2 06:34:02.212: Allocated IP address = 180.40.7.138 255.255.255.224 R4(config-if)# R4(config-if)# *Mar 2 06:34:02.212: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.138, mask 255.255.255.224, hostname R4 R4(config-if)# *Mar 2 06:34:25.956: DHCP: QScan: Purging entry *Mar 2 06:34:25.956: DHCP: deleting entry 6223D8F4 0.0.0.0 from list *Mar 2 06:34:25.956: Temp IP addr: 0.0.0.0 for peer on Interface: unknown *Mar 2 06:34:25.956: Temp sub net mask: 255.255.255.224 *Mar 2 06:34:25.956: DHCP Lease server: 180.40.7.129, state: 8 Purging *Mar 2 06:34:25.956: DHCP transaction id: 68E1AA9 *Mar 2 06:34:25.956: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:34:25.956: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:34:25.956: No timer running *Mar 2 06:34:25.956: Retry count: 0 Client-ID: *Mar 2 06:34:25.956: Hostname: R4 R4(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip dhcp bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 0100.3085.f36f.40 Infinite Manual 180.40.7.138 0063.6973.636f.2d30. Mar 03 1993 06:31 AM Automatic 3033.302e.3835.6633. 2e36.6634.302d.4661. 302f.30 R3# *Mar 2 06:32:14.412: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3#sh ip dhcp binclea ip dhcp bin * R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] * R4(config-if)#ip add dhcp nt fa 0/0 do deb dhcp deu all no shutshut int fa 0/0no shut shut int fa 0/0p add dhcp cli fa 0/0 *Mar 2 06:35:33.292: DHCP: SRelease attempt # 1 for entry: *Mar 2 06:35:33.292: Temp IP addr: 180.40.7.138 for peer on Interface: FastEthernet0/0 *Mar 2 06:35:33.292: Temp sub net mask: 255.255.255.224 *Mar 2 06:35:33.292: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:35:33.292: DHCP transaction id: 68F105C *Mar 2 06:35:33.292: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:35:33.292: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:35:33.292: Next timer fires after: 00:00:00 *Mar 2 06:35:33.292: Retry count: 1 Client-ID: cisco-0030.85f3.6f40-Fa0/0 *Mar 2 06:35:33.292: Hostname: R4 *Mar 2 06:35:33.296: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:35:33.296: DHCP: SRelease: 279 bytes *Mar 2 06:35:33.360: DHCP: SRelease attempt # 2 for entry: *Mar 2 06:35:33.360: Temp IP addr: 180.40.7.138 for peer on Interface: FastEthernet0/0 *Mar 2 06:35:33.360: Temp sub net mask: 255.255.255.224 *Mar 2 06:35:33.360: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:35:33.360: DHCP transaction id: 68F105C *Mar 2 06:35:33.360: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:35:33.360: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:35:33.360: Next timer fires after: 00:00:00 *Mar 2 06:35:33.360: Retry count: 2 Client-ID: cisco-0030.85f3.6f40-Fa0/0 *Mar 2 06:35:33.360: Hostname: R4 *Mar 2 06:35:33.364: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:35:33.364: DHCP: SRelease: 279 bytes *Mar 2 06:35:33.364: DHCP: Releasing ipl options: *Mar 2 06:35:33.364: Clearing default gateway and route to 180.40.7.132 *Mar 2 06:35:33.364: Removing old default route 180.40.7.132 *Mar 2 06:35:33.368: Clearing DNS address 208.28.1.82 *Mar 2 06:35:33.368: Clearing R4(config-if)#default domain of ccie.com *Mar 2 06:35:34.288: DHCP: SRelease attempt # 3 for entry: *Mar 2 06:35:34.288: Temp IP addr: 180.40.7.138 for peer on Interface: FastEthernet0/0 *Mar 2 06:35:34.288: Temp sub net mask: 255.255.255.224 *Mar 2 06:35:34.288: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 06:35:34.288: DHCP transaction id: 68F105C *Mar 2 06:35:34.288: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:35:34.288: Next timer fires after: 00:00:01 *Mar 2 06:35:34.288: Retry count: 3 Client-ID: cisco-0030.85f3.6f40-Fa0/0 *Mar 2 06:35:34.288: Hostname: R4 *Mar 2 06:35:34.288: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 06:35:34.292: DHCP: SRelease: 279 bytes *Mar 2 06:35:35.368: RAC: DHCP stopped on interface FastEthernet0/0 *Mar 2 06:35:35.368: DHCP: DHCP client process started: 10 *Mar 2 06:35:35.368: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 06:35:35.368: DHCP: Try 1 to acquire address for FastEthernet0/0 *Mar 2 06:35:35.372: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 06:35:35.372: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 06:35:35.396: DHCP: allocate request *Mar 2 06:35:35.396: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 06:35:35.400: DHCP: new entry. add to queue *Mar 2 06:35:35.400: DHCP: SDiscover attempt # 1 for entry: *Mar 2 06:35:35.400: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 06:35:35.400: Temp sub net mask: 0.0.0.0 *Mar 2 06:35:35.400: DHCP Lease server: 0.0.0.0, state: 1 Selecting *Mar 2 06:35:35.400: DHCP transaction id: 69099BF *Mar 2 06:35:35.400: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 06:35:35.400: Next timer fires after: 00:00:03 *Mar 2 06:35:35.400: Retry count: 1 Client-ID: 0030.85f3.6f40 *Mar 2 06:35:35.400: Hostname: R4 *Mar 2 06:35:35.404: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 06:35:35.404: DHCP: SDiscover 274 bytes *Mar 2 06:35:35.404: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 06:35:35.412: DHCP: Received a BOOTREP pkt *Mar 2 06:35:35.412: DHCP: Scan: Message type: DHCP Offer *Mar 2 06:35:35.412: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 06:35:35.416: DHCP: Scan: Lease Time: 86400 *Mar 2 06:35:35.416: DHCP: Scan: Renewal time: 43200 *Mar 2 06:35:35.416: DHCP: Scan: Rebind time: 75600 *Mar 2 06:35:35.416: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 06:35:35.416: DHCP: Scan: Router Option: 180.40.7.132, 180.40.7.133 *Mar 2 06:35:35.416: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 06:35:35.416: DHCP: Scan: Domain Name: ccie.com *Mar 2 06:35:35.416: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 06:35:35.416: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 06:35:35.416: UDP sport: 43, dport: 44, length: 314 *Mar 2 06:35:35.416: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 06:35:35.416: DHCP server identifier: 180.40.7.129 *Mar 2 06:35:35.420: xid: 69099BF, secs: 0, flags: 8000 *Mar 2 06:35:35.420: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 06:35:35.420: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 06:35:35.420: options block length: 66 *Mar 2 06:35:35.420: DHCP Offer Message Offered Address: 180.40.7.130 *Mar 2 06:35:35.420: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 06:35:35.420: DHCP: Server ID Option: 180.40.7.129 *Mar 2 06:35:35.420: DHCP: offer received from 180.40.7.129 *Mar 2 06:35:35.420: DHCP: SRequest attempt # 1 for entry: *Mar 2 06:35:35.420: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 06:35:35.420: Temp sub net mask: 255.255.255.224 *Mar 2 06:35:35.424: DHCP Lease server: 180.40.7.129, state: 2 Requesting *Mar 2 06:35:35.424: DHCP transaction id: 69099BF *Mar 2 06:35:35.424: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 06:35:35.424: Next timer fires after: 00:00:01 *Mar 2 06:35:35.424: Retry count: 1 Client-ID: 0030.85f3.6f40 *Mar 2 06:35:35.424: Hostname: R4 *Mar 2 06:35:35.424: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 06:35:35.424: DHCP: SRequest- Requested IP addr option: 180.40.7.130 *Mar 2 06:35:35.424: DHCP: SRequest placed lease len option: 86400 *Mar 2 06:35:35.424: DHCP: SRequest: 292 bytes *Mar 2 06:35:35.424: DHCP: SRequest: 292 bytes *Mar 2 06:35:35.428: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 06:35:35.432: DHCP: Received a BOOTREP pkt *Mar 2 06:35:35.436: DHCP: Scan: Message type: DHCP Ack *Mar 2 06:35:35.436: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 06:35:35.436: DHCP: Scan: Lease Time: 86400 *Mar 2 06:35:35.436: DHCP: Scan: Renewal time: 43200 *Mar 2 06:35:35.436: DHCP: Scan: Rebind time: 75600 *Mar 2 06:35:35.436: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 06:35:35.436: DHCP: Scan: Router Option: 180.40.7.132, 180.40.7.133 *Mar 2 06:35:35.436: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 06:35:35.436: DHCP: Scan: Domain Name: ccie.com *Mar 2 06:35:35.436: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 06:35:35.436: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 06:35:35.440: UDP sport: 43, dport: 44, length: 314 *Mar 2 06:35:35.440: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 06:35:35.440: DHCP server identifier: 180.40.7.129 *Mar 2 06:35:35.440: xid: 69099BF, secs: 0, flags: 8000 *Mar 2 06:35:35.440: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 06:35:35.440: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 06:35:35.440: options block length: 66 *Mar 2 06:35:35.440: DHCP Ack Message *Mar 2 06:35:35.440: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 06:35:35.440: DHCP: Server ID Option: 180.40.7.129 *Mar 2 06:35:38.452: DHCP: Releasing ipl options: *Mar 2 06:35:38.452: DHCP: Applying DHCP options: *Mar 2 06:35:38.456: Setting default_gateway to 180.40.7.132 *Mar 2 06:35:38.456: Adding default route 180.40.7.132 *Mar 2 06:35:39.456: Adding DNS server address 208.28.1.82 *Mar 2 06:35:39.456: Setting default domain to ccie.com *Mar 2 06:35:39.456: DHCP Client Pooling: ***Allocated IP address: 180.40.7.130 *Mar 2 06:35:39.500: Allocated IP address = 180.40.7.130 255.255.255.224 *Mar 2 06:35:39.500: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.224, hostname R4 R4(config-if)# R4(config-if)#^Z R4#sh do *Mar 2 06:35:57.524: %SYS-5-CONFIG_I: Configured from console by console R4#sh dom R4#sh domain ^ % Invalid input detected at '^' marker. R4#sh domainidomainpdomain domain ccie.com R4# R4# R4# *Mar 2 06:36:05.288: DHCP: QScan: Purging entry *Mar 2 06:36:05.288: DHCP: deleting entry 63050194 0.0.0.0 from list *Mar 2 06:36:05.288: Temp IP addr: 0.0.0.0 for peer on Interface: unknown *Mar 2 06:36:05.288: Temp sub net mask: 255.255.255.224 *Mar 2 06:36:05.288: DHCP Lease server: 180.40.7.129, state: 8 Purging *Mar 2 06:36:05.288: DHCP transaction id: 68F105C *Mar 2 06:36:05.288: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 06:36:05.288: Temp default-gateway addr: 180.40.7.132 *Mar 2 06:36:05.288: No timer running *Mar 2 06:36:05.288: Retry count: 0 Client-ID: *Mar 2 06:36:05.288: Hostname: R4 R4#u all All possible debugging has been turned off R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 180.40.7.132 to network 0.0.0.0 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 S* 0.0.0.0/0 [254/0] via 180.40.7.132 R4# *Mar 2 06:36:18.472: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4# sh ip route *Mar 2 06:36:23.468: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 180.40.7.132 to network 0.0.0.0 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 00:00:03, FastEthernet0/0 [110/793] via 180.40.7.131, 00:00:03, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.129, 00:00:03, FastEthernet0/0 [110/783] via 180.40.7.131, 00:00:03, FastEthernet0/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:03, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.129, 00:00:04, FastEthernet0/0 [110/782] via 180.40.7.131, 00:00:04, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:00:04, FastEthernet0/0 --More--  O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:04, FastEthernet0/0 O 180.40.7.64/27 [110/782] via 180.40.7.131, 00:00:04, FastEthernet0/0 [110/782] via 180.40.7.129, 00:00:04, FastEthernet0/0 S* 0.0.0.0/0 [254/0] via 180.40.7.132 R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run | b h dhcp ip dhcp excluded-address 180.40.7.129 ip dhcp excluded-address 180.40.7.131 180.40.7.134 ! ip dhcp pool Prob13 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 180.40.7.133 dns-server 208.28.1.82 domain-name ccie.com option 150 ip 20.20.20.20 ! ip dhcp pool ForR4 host 180.40.7.130 255.255.255.224 client-identifier 0100.3085.f36f.40 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! ! ! ! --More--   R3#3#sh run | b dhcp ^ % Invalid input detected at '^' marker. R3# R3#^x21 % Unknown command or computer name, or unable to find computer address R3# R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip dhcp ex R2(config)#ip dhcp excluded-address 2x08.28.       0.10.1.1 R2(config)#ip dhcp poo R2(config)#ip dhcp pool Prob14 R2(dhcp-config)#net R2(dhcp-config)#net   net R2(dhcp-config)#netw R2(dhcp-config)#network 20.110.1.0.1. .0.1.0.1. 0.1.0 /24 R2(dhcp-config)# RACK11AS>6 [Resuming connection 6 to r6 ... ] 1d0 S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 9.2   0. /2 S6(config-if)#ip add hdcp ^ % Invalid input detected at '^' marker. S6(config-if)#ip add hdcp    dhcpo \  S6(config-if)# 1d06h: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on FastEthernet0/2 from FULL to DOWN, Neighbor Down: Interface down or detached S6(config-if)#Interface FastEthernet0/2 assigned DHCP address 20.10.1.2, mask 255.255.255.0 do       1d06h: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on FastEthernet0/2 from LOADING to FULL, Loading Done S6(config-if)# RACK11AS>2 [Resuming connection 2 to r2 ... ] *M R2(dhcp-config)#do sh ip dhcp binm  % Ambiguous command: "do sh ip dhcp bin" R2(config)#do sh ip dhcp bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 20.10.1.2 0063.6973.636f.2d30. Mar 03 1993 06:47 AM Automatic 3030.612e.6634.3961. 2e32.3338.302d.4661. 302f.32 R2(config)# R2# *Mar 2 06:48:15.587: %SYS-5-CONFIG_I: Configured from console by console R2# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6(config-if)#ip add 20.10.1.2 255.255.255.0 S6(config-if)#^Z S6# RACK11AS>3 [Resuming connection 3 to r3 ... ] * R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#clea ip dhcp bin % Incomplete command. R2#clea ip dhcp bin * R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#do sh ip dhcp binnetwork 20.10.1.0 /24ip dhcp pool Prob14  R2(dhcp-config)#ip dhcp pool Prob14do sh ip dhcp bin network 20.10.1.0 /24nnetwork 20.10.1.0 /24onetwork 20.10.1.0 /24 network 20.10.1.0 /24 R2(dhcp-config)#host 20.10.1.2 /24 R2(dhcp-config)#cli R2(dhcp-config)#client-i R2(dhcp-config)#client-identifier 0063.6973.636f.2d30.3030.612e.6634.3961.2e3$tifier 0063.6973.636f.2d30.3030.612e.6634.3961.2e32 .3338.3023.6973.636f.2d30.3030.612e.6634.3961.2e32.3338.302d .4661.302f.2d30.3030.612e.6634.3961.2e32.3338.302d.4661.302f .32 R2(dhcp-config)#^Z R2#confi *Mar 2 06:49:43.588: %SYS-5-CONFIG_I: Configured from console by console R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int0.   fa 0/1 R2(config-if)#ip heal    lp 208.28.1.. 99 R2(config-if)#^Z R2# *Mar 2 06:50:07.411: %SYS-5-CONFIG_I: Configured from console by console R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#^Z R2# RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#s 0/0.2 % Incomplete command. R7(config)#s 0/0.2e 0/0.2r 0/0.2 0/0.2 1/0.2 ^ % Invalid input detected at '^' marker. R7(config)#ser 1/0.2/0.2 iser /0.2nser /0.2tser /0.2 ser /0.2ser 0/0.2 ^ % Invalid input detected at '^' marker. R7(config)#int ser 0/0.2/0.2 1/0.2 R7(config-subif)#\int ser 1/0.2\  ip    ip help 208.28.1.99 R7(config-subif)#do sh run int s 1/0.1 2 Building configuration... Current configuration : 239 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 end R7(config-subif)#frame-relay interface-dlci 702 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R7(config-subif)#frame-relay interface-dlci 702 pro R7(config-subif)#frame-relay interface-dlci 702 protocol ? A.B.C.D Protocol specific address ip IP R7(config-subif)#frame-relay interface-dlci 702 protocol 180.40.7.162 %Can't add another VC to point-to-point subinterface R7(config-fr-dlci)#frame-relay interface-dlci 702 protocol 180.40.7.162do sh run int s 1/0.2 frame-relay interface-dlci 702 protocol 180.40.7.162 no frame-relay interface-dlci 702 R7(config-subif)#no frame-relay interface-dlci 702frame-relay interface-dlci 702 protocol 180.40.7.162 R7(config-fr-dlci)# *Mar 1 22:58:51.819: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-fr-dlci)# R7(config-fr-dlci)# R7(config-fr-dlci)# R7(config-fr-dlci)#^Z R7# *Mar 1 22:58:59.872: %SYS-5-CONFIG_I: Configured from console by console R7# *Mar 1 22:59:20.811: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7# R7# R7# R7# RACK11AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh ru n  n | b ip dhcp ip dhcp excluded-address 20.10.1.1 ! ip dhcp pool Prob14 host 20.10.1.2 255.255.255.0 client-identifier 0063.6973.636f.2d30.3030.612e.6634.3961.2e32.3338.302d.4661.302f.32 ! ip cef no ip domain lookup ip audit po max-events 100 frame-relay de-list 1 protocol ip list 100 ! ! ! ! ! ! ! ! ! ! ! ! --More--  ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto --More--  ! --More--  interface Serial1/0 --More--   R2# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#SH RU   un |   int s 1? / R7#SH Run int s 10.   1/0.2 Building configuration... Current configuration : 261 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 end R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#gl R7(config-if)#glbp ? <0-1023> Group number R7(config-if)#glbp 71 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 71 ikp  p ? A.B.C.D Virtual IP address R7(config-if)#glbp 71 ip 180.40.7.134 ? secondary Make this IP address a secondary address R7(config-if)#glbp 71 ip 180.40.7.134 R7(config-if)#glbp 71 ip 180.40.7.134                 pri R7(config-if)#glbp 71 priority 110 R7(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#glbp 71 ip 180.40.7.134 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Init (interface down) Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is unknown Standby is unknown Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There are no forwarders R3(config-if)# *Mar 2 06:55:52.909: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 71 Fwd 2 state Listen -> Active R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:00:21 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.679 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 8.593 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14398.593 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.589 sec) Forwarder 2 State is Active --More--   1 state change, last state change 00:00:58 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 100 R3(config-if)#exit R3(config)#track 3 ? interface Select an interface to track ip IP protocol R3(config)#track 3 ip ? route IP route R3(config)#track 3 ip rout 20.10.1.0/24 rea R3(config-track)#exit R3(config)#int f 0/0 R3(config-if)#int f 0/0exit track 3 ip rout 20.10.1.0/24 reaexit do sh glbpglbp 71 ip 180.40.7.134               we R3(config-if)#glbp 71 weighting ? <1-254> Weighting maximum value track Interface tracking R3(config-if)#glbp 71 weighting tra R3(config-if)#glbp 71 weighting track ? <1-500> Tracked object R3(config-if)#glbp 71 weighting track 3 ? decrement Weighting decrement R3(config-if)#glbp 71 weighting track 3 dec 50 ? R3(config-if)#glbp 71 weighting track 3 dec 50 R3(config-if)# RACK11AS>7 [Resuming connection 7 to r7 ... ] *Ma R7(config-if)#exit R7(config)#track 3 ip            track 3 ip rout 20.10.1.0/24 rea R7(config-track)#int fa 0/1 R7(config-if)#int fa 0/1track 3 ip rout 20.10.1.0/24 rea exit glbp 71 priority 110            we R7(config-if)#glbp 71 weighting tra 3 dec 50 R7(config-if)#do    glbp 71 weighting tra 3 dec 50nglbp 71 weighting tra 3 dec 50oglbp 71 weighting tra 3 dec 50 glbp 71 weighting tra 3 dec 50 R7(config-if)# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa 0/.1  1 R2(config-if)#shut R2(config-if)# *Mar 2 07:01:45.327: %OSPF-5-ADJCHG: Process 1, Nbr 20.10.2.1 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:05:51 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.667 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 8.586 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 3 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14398.586 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.582 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:05:59 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 100 R3(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:00:14, FastEthernet0/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:14, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:00:14, Serial1/0 [110/781] via 180.40.7.2, 00:00:14, Serial1/2 O 180.40.7.161/32 [ *Mar 2 07:02:01.834: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Active -> Speak110/1] via 180.40.7.131, 00:00:14, FastEthernet0/0 C 180.40.7.0/27 is directly connected, Serial1/2 C 180.40.7.64/27 is directly connected, Serial1/0 R3(config-if)#  do sh ip routeglbp  FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:06:12 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.203 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 8.121 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14398.121 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.117 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:06:21 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:06:41 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.460 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 9.379 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14399.379 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.375 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:06:50 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:06:45 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.315 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 8.237 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14398.233 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.233 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:06:54 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:07:06 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.892 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 8.815 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14398.810 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.806 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:07:14 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:07:11 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.740 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 9.663 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14399.659 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.659 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:07:19 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:07:16 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.766 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 7.684 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14397.684 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.680 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:07:24 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:07:21 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.455 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 8.377 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14398.373 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.369 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:07:29 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:07:27 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.824 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 8.746 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14398.742 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.742 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:07:35 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:07:31 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.362 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 7.284 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14397.280 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.280 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:07:40 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:07:39 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.767 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 8.690 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14398.686 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.686 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:07:47 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:07:51 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.948 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 8.866 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14398.862 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.862 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:07:59 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:07:58 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.810 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 7.732 sec) Standby is local Priority 100 (default) Weighting 50 (default 100), thresholds: lower 1, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14397.728 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.728 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:08:06 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#config t        glba p 71 wei R3(config-if)#glbp 71 weighting ? <1-254> Weighting maximum value track Interface tracking R3(config-if)#glbp 71 weighting 100 ? lower Weighting lower threshold upper Weighting upper threshold R3(config-if)#glbp 71 weighting 100 lo R3(config-if)#glbp 71 weighting 100 lower 90 ? upper Weighting upper threshold R3(config-if)#glbp 71 weighting 100 lower 90 up 100 R3(config-if)# RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar R7(config-if)#glbp 71 weighting 100 lower 90 up 100 R7(config-if)#do sh glbp FastEthernet0/1 - Group 71 State is Active 2 state changes, last state change 00:10:11 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.596 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 8.673 sec) Priority 110 (configured) Weighting 100 (configured 100), thresholds: lower 90, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:10:01 MAC address is 0007.b400.4701 (default) Owner ID is 0012.7f8e.c6c1 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 Forwarder 2 --More--   State is Listen MAC address is 0007.b400.4702 (learnt) Owner ID is 0012.7f8d.3ca0 Redirection enabled, 598.016 sec remaining (maximum 600 sec) Time to live: 14398.016 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 50 (expires in 8.016 sec) R7(config-if)#do sh glbp FastEthernet0/1 - Group 71 State is Active 2 state changes, last state change 00:10:15 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.420 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 7.496 sec) Priority 110 (configured) Weighting 100 (configured 100), thresholds: lower 90, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:10:05 MAC address is 0007.b400.4701 (default) Owner ID is 0012.7f8e.c6c1 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 Forwarder 2 --More--   State is Listen MAC address is 0007.b400.4702 (learnt) Owner ID is 0012.7f8d.3ca0 Redirection enabled, 598.750 sec remaining (maximum 600 sec) Time to live: 14398.750 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 50 (expires in 8.746 sec) R7(config-if)#do sh glbp FastEthernet0/1 - Group 71 State is Active 2 state changes, last state change 00:10:19 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.301 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 9.375 sec) Priority 110 (configured) Weighting 100 (configured 100), thresholds: lower 90, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:10:09 MAC address is 0007.b400.4701 (default) Owner ID is 0012.7f8e.c6c1 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 Forwarder 2 --More--   State is Listen MAC address is 0007.b400.4702 (learnt) Owner ID is 0012.7f8d.3ca0 Redirection enabled, 598.281 sec remaining (maximum 600 sec) Time to live: 14398.281 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 50 (expires in 8.277 sec) R7(config-if)#do sh glbp FastEthernet0/1 - Group 71 State is Active 2 state changes, last state change 00:10:26 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.836 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 8.914 sec) Priority 110 (configured) Weighting 100 (configured 100), thresholds: lower 90, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:10:16 MAC address is 0007.b400.4701 (default) Owner ID is 0012.7f8e.c6c1 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 Forwarder 2 --More--   State is Listen MAC address is 0007.b400.4702 (learnt) Owner ID is 0012.7f8d.3ca0 Redirection enabled, 598.077 sec remaining (maximum 600 sec) Time to live: 14398.077 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 50 (expires in 8.073 sec) R7(config-if)#do sh glbp FastEthernet0/1 - Group 71 State is Active 2 state changes, last state change 00:10:41 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.612 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 8.686 sec) Priority 110 (configured) Weighting 100 (configured 100), thresholds: lower 90, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:10:31 MAC address is 0007.b400.4701 (default) Owner ID is 0012.7f8e.c6c1 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 Forwarder 2 --More--   State is Listen MAC address is 0007.b400.4702 (learnt) Owner ID is 0012.7f8d.3ca0 Redirection enabled, 597.416 sec remaining (maximum 600 sec) Time to live: 14397.416 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 50 (expires in 7.412 sec) R7(config-if)#do sh glbp FastEthernet0/1 - Group 71 State is Active 2 state changes, last state change 00:10:46 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.586 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 9.664 sec) Priority 110 (configured) Weighting 100 (configured 100), thresholds: lower 90, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:10:36 MAC address is 0007.b400.4701 (default) Owner ID is 0012.7f8e.c6c1 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 Forwarder 2 --More--   State is Listen MAC address is 0007.b400.4702 (learnt) Owner ID is 0012.7f8d.3ca0 Redirection enabled, 598.458 sec remaining (maximum 600 sec) Time to live: 14398.458 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 50 (expires in 8.454 sec) R7(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#sh    glbp 71 weighting 100 lower 90 up 100do sh glbp  FastEthernet0/0 - Group 71 State is Standby 1 state change, last state change 00:10:32 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.025 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 110 (expires in 9.948 sec) Standby is local Priority 100 (default) Weighting 50 (configured 100), thresholds: lower 90, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Time to live: 14399.944 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.940 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:10:41 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#do sh glbpglbp 71 weighting 100 lower 90 up 100do sh glbp  FastEthernet0/1 - Group 71 State is Active 2 state changes, last state change 00:11:13 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.070 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 7.147 sec) Priority 110 (configured) Weighting 100 (configured 100), thresholds: lower 90, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:11:03 MAC address is 0007.b400.4701 (default) Owner ID is 0012.7f8e.c6c1 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 Forwarder 2 --More--   State is Listen MAC address is 0007.b400.4702 (learnt) Owner ID is 0012.7f8d.3ca0 Redirection enabled, 598.506 sec remaining (maximum 600 sec) Time to live: 14398.506 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 50 (expires in 8.502 sec) R7(config-if)# RACK11AS> [Resuming connection 7 to r7 ... ] R7(config-if)# R7(config-if)#shut R7(config-if)# *Mar 1 23:13:55.693: %VRRP-6-STATECHANGE: Fa0/1 Grp 71 state Backup -> Init *Mar 1 23:13:55.697: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Active -> Init *Mar 1 23:13:55.697: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 71 Fwd 1 state Active -> Init *Mar 1 23:13:55.701: %GLBP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Active -> Init R7(config-if)#nop *Mar 1 23:13:55.705: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/1 from 2WAY to DOWN, Neighbor Down: Interface down or detached *Mar 1 23:13:55.705: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-if)#nop  shut *Mar 1 23:13:57.696: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down *Mar 1 23:13:58.698: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down R7(config-if)#no shut RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-if)#do sh glbp FastEthernet0/0 - Group 71 State is Active 2 state changes, last state change 00:00:07 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.790 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is unknown Priority 100 (default) Weighting 50 (configured 100), thresholds: lower 90, upper 100 Track object 3 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (2 active) Forwarder 1 State is Active 1 state change, last state change 00:00:07 MAC address is 0007.b400.4701 (learnt) Owner ID is 0012.7f8e.c6c1 Redirection enabled, 582.784 sec remaining (maximum 600 sec) Time to live: 14382.780 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec --More--   Active is local, weighting 50 Forwarder 2 State is Active 1 state change, last state change 00:11:46 MAC address is 0007.b400.4702 (default) Owner ID is 0012.7f8d.3ca0 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)#^x7    *Mar 2 07:07:52.581: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired R3(config-if)# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#no shut R7(config-if)#^Z R7# *Mar 1 23:15:08.176: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 23:15:08.420: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#^Z R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.162 0 FULL/ - 00:01:56 180.40.7.162 Serial1/0.2 180.40.7.129 1 FULL/DR 00:00:39 180.40.7.66 Serial1/0.1 208.28.1.2 1 FULL/DR 00:00:36 208.28.1.2 FastEthernet0/0 R7# *Mar 1 23:15:18.637: %VRRP-6-STATECHANGE: Fa0/1 Grp 71 state Backup -> Master R7# R7# *Mar 1 23:15:24.995: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 71 Fwd 1 state Listen -> Active *Mar 1 23:15:24.995: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 71 Fwd 2 state Listen -> Active R7# *Mar 1 23:15:34.996: %GLBP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Standby -> Active *Mar 1 23:15:35.977: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Standby -> Active R7# *Mar 1 23:15:40.997: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 71 Fwd 2 state Active -> Listen *Mar 1 23:15:41.366: %VRRP-6-STATECHANGE: Fa0/1 Grp 71 state Master -> Backup R7# R7# R7# R7# R7#sh glbp *Mar 1 23:15:58.454: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/1 from LOADING to FULL, Loading Done *Mar 1 23:15:58.462: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/1 from LOADING to FULL, Loading Done R7#sh glbp FastEthernet0/1 - Group 71 State is Active 5 state changes, last state change 00:00:36 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.038 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 7.031 sec) Priority 110 (configured) Weighting 100 (configured 100), thresholds: lower 90, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 3 state changes, last state change 00:00:46 MAC address is 0007.b400.4701 (default) Owner ID is 0012.7f8e.c6c1 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 Forwarder 2 --More--   State is Listen 2 state changes, last state change 00:00:32 MAC address is 0007.b400.4702 (learnt) Owner ID is 0012.7f8d.3ca0 Redirection enabled, 598.870 sec remaining (maximum 600 sec) Time to live: 14398.870 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 50 (expires in 8.866 sec) R7#sh glbp FastEthernet0/1 - Group 71 State is Active 5 state changes, last state change 00:02:18 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.166 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 7.163 sec) Priority 110 (configured) Weighting 100 (configured 100), thresholds: lower 90, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 3 state changes, last state change 00:02:28 MAC address is 0007.b400.4701 (default) Owner ID is 0012.7f8e.c6c1 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 Forwarder 2 --More--   State is Listen 2 state changes, last state change 00:02:14 MAC address is 0007.b400.4702 (learnt) Owner ID is 0012.7f8d.3ca0 Redirection enabled, 598.918 sec remaining (maximum 600 sec) Time to live: 14398.918 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 50 (expires in 8.918 sec) R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] * R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Ma R2(config-if)#no shut R2(config-if)#^Z R2# *Mar 2 07:11:34.448: %SYS-5-CONFIG_I: Configured from console by console R2# *Mar 2 07:11:36.143: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int fa 0/0 Building configuration... Current configuration : 434 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 71 ip 180.40.7.133 vrrp 71 priority 111 glbp 71 ip 180.40.7.134 glbp 71 weighting 100 lower 90 glbp 71 weighting track 3 decrement 50 standby 71 ip 180.40.7.132 standby 71 priority 150 standby 71 preempt standby 71 track Serial1/2 51 standby 71 track 2 decrement 61 service-policy input test end R3# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int fa 0/1 Building configuration... Current configuration : 280 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 71 ip 180.40.7.133 glbp 71 ip 180.40.7.134 glbp 71 priority 110 glbp 71 weighting 100 lower 90 standby 71 ip 180.40.7.132 standby 71 preempt service-policy output Prob6 end R7# R7# *Mar 1 23:19:09.046: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 71 state Active -> Speak R7#^x   RACK11AS>6 [Resuming connection 6 to r6 ... ] 1d S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 175 R S 2611XM Fas 0/1 R1 Fas 0/1 177 R 2611 Eth 0/1 R7 Fas 0/7 143 R S 2611XM Fas 0/1 R4 Fas 0/4 129 R 3620 Fas 0/0 S5 Fas 0/24 130 R S I WS-C3550-2Fas 0/24 S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#^Z S6#s 1d07h: %SYS-5-CONFIG_I: Configured from console by console S6#sh mls qos > ? aggregate-policer Show aggregate-policer information interface Show interface information maps Show mapping information | Output modifiers S6#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Default DSCP Mutation Map: --More--   S6#[B  config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#mls qos map ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S6(config)#mls qos map d S6(config)#mls qos map dscp-       ip S6(config)#mls qos map ip-prec-dscp ? <0-63> 8 dscp values separated by spaces S6(config)#mls qos map ip-prec-dscp 0 14 16 28 32 40 480  56 S6(config)#do sh mls qo map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 14 16 28 32 40 48 56 Dscp-dscp mutation map: Default DSCP Mutation Map: --More--   S6(config)# RACK11AS>5 [Resuming connection 5 to r5 ... ] 1d0 S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh pol int s 1   fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: Prec1 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: precedence 1 Class-map: Prec3 (match-all) 60 packets, 6840 bytes 5 minute offered rate 2000 bps Match: precedence 3 Class-map: class-default (match-any) 20302 packets, 1923837 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class   R3(config)#class-map dscp  24 R3(config-cmap)#match sw  dscp 24 R3(config-cmap)#w exit R3(config)#class dscp28 ^ % Invalid input detected at '^' marker. R3(config)#class dscp28- dscp28m dscp28a dscp28p dscp28 R3(config-cmap)#match dscp 28 R3(config-cmap)#pol test R3(config-pmap)#do sh run | b pol policy-map test class Prec1 class Prec3 policy-map Prob9 class FTP bandwidth remaining percent 50 class Telnet bandwidth remaining percent 25 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 71 ip 180.40.7.133 vrrp 71 priority 111 --More--   R3(config-pmap)#no class Prec3 R3(config-pmap)#class dscp28 R3(config-pmap-c)#exit R3(config-pmap)#exitclass dscp28 4 R3(config-pmap-c)#^Z R3# *Mar 2 07:23:28.647: %SYS-5-CONFIG_I: Configured from console by consoleconfig t R3#config tsh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: Prec1 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: precedence 1 Class-map: dscp28 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: dscp24 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: class-default (match-any) 20422 packets, 1933997 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: Prec1 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: precedence 1 Class-map: dscp28 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: dscp24 (match-all) 25 packets, 2850 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: class-default (match-any) 20432 packets, 1934847 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6(config)#ml qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S6(config)# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: Prec1 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: precedence 1 Class-map: dscp28 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: dscp24 (match-all) 25 packets, 2850 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: class-default (match-any) 20504 packets, 1942121 bytes 5 minute offered rate 2000 bps, drop rate 0 bps Match: any R3#   RACK11AS>6 [Resuming connection 6 to r6 ... ] S6(config)#int fa 0/7 S6(config-if)#mls qos pr S6(config-if)#mls qos pr ^ % Invalid input detected at '^' marker. S6(config-if)#mls qos pre S6(config-if)#mls qos pre   tr S6(config-if)#mls qos trust pre ^ % Invalid input detected at '^' marker. S6(config-if)#mls qos trust pre   ? cos Classify by packet COS device trusted device class dscp Classify by packet DSCP ip-precedence Classify by packet IP precedence S6(config-if)#mls qos trust ip S6(config-if)#mls qos trust ip-precedence S6(config-if)#^Z S6# 1d07h: %SYS-5-CONFIG_I: Configured from console by console S6# RACK11AS>5 [Resuming connection 5 to r5 ... ] ping 180.40.7.129config t ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# S5# S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: Prec1 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: precedence 1 Class-map: dscp28 (match-all) 30 packets, 3420 bytes 5 minute offered rate 2000 bps Match: dscp af32 (28) Class-map: dscp24 (match-all) 25 packets, 2850 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: class-default (match-any) 20555 packets, 1946435 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh clas Class Map match-all dscp24 (id 5) Match dscp cs3 (24) Class Map match-all dscp28 (id 6) Match dscp af32 (28) Class Map match-all Prec1 (id 1) Match precedence 1 Class Map match-all Prec3 (id 2) Match precedence 3 Class Map match-all Telnet (id 4) Match protocol telnet Class Map match-any class-default (id 0) Match any Class Map match-any FTP (id 3) Match protocol ftp Match access-group 103 R3#sh run | b class class-map match-all dscp24 match dscp cs3 class-map match-all dscp28 match dscp af32 class-map match-all Prec1 match precedence 1 class-map match-all Prec3 match precedence 3 class-map match-all Telnet match protocol telnet class-map match-any FTP match protocol ftp match access-group 103 ! ! policy-map test class Prec1 class dscp28 class dscp24 policy-map Prob9 class FTP bandwidth remaining percent 50 class Telnet --More--   R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#sh run | b mls go  qos mls qos map ip-prec-dscp 0 14 16 28 32 40 48 56 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 no switchport ip address 20.10.2.1 255.255.255.0 ! interface FastEthernet0/2 --More--   no switchport ip address 20.10.1.2 255.255.255.0 ! interface FastEthernet0/3 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport access vlan 10 switchport mode access spanning-tree portfast ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 switchport access vlan 10 switchport mode dynamic desirable mls qos trust ip-precedence ! interface FastEthernet0/8 --More--   switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable ! interface FastEthernet0/14 switchport mode dynamic desirable ! interface FastEthernet0/15 switchport mode dynamic desirable ! --More--  interface FastEthernet0/16 switchport mode dynamic desirable ! interface FastEthernet0/17 switchport mode dynamic desirable ! interface FastEthernet0/18 switchport mode dynamic desirable ! interface FastEthernet0/19 switchport mode dynamic desirable ! interface FastEthernet0/20 switchport mode dynamic desirable ! interface FastEthernet0/21 switchport mode dynamic desirable ! interface FastEthernet0/22 switchport mode dynamic desirable ! interface FastEthernet0/23 switchport mode dynamic desirable --More--  ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ip http server ip http secure-server ! --More--  ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 privilege level 15 no login line vty 5 15 no login ! ! end S6# S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#mls S6(config)#mls ? aclmerge Modify behavior of ACL merge qos QoS parameters S6(config)#mls qos ? aggregate-policer Assign aggregate policer cos Configure CoS setting map Define QoS mapping min-reserve Configure min-reserve buffers S6(config)#mls qos map ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S6(config)#mls qos map dsc S6(config)#mls qos map dscp-m S6(config)#mls qos map dscp-mutation ? WORD DSCP mutation map name S6(config)#mls qos map dscp-mutation Provb b  b17 ? <0-63> DSCP values separated by spaces (up to 8 values total) S6(config)#mls qos map dscp-mutation Prob17 28 to 26 S6(config)#mls qos map dscp-mutation Prob17 28 to 26        14 to 12 S6(config)#int fa 0/24 S6(config-if)#mls qos ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S6(config-if)#mls qos ds S6(config-if)#mls qos dscp-mutation Prob17 S6(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#confg ig t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class   R3(config)#class-map dscp26 R3(config-cmap)#match de scp af31 R3(config-cmap)#exit R3(config)#pol test R3(config-pmap)#do sh run | b pol policy-map test class Prec1 class dscp28 class dscp24 policy-map Prob9 class FTP bandwidth remaining percent 50 class Telnet bandwidth remaining percent 25 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 71 ip 180.40.7.133 --More--   R3(config-pmap)#no class dscp24 R3(config-pmap)#no class dscp24 6no class dscp26  class dscp26  R3(config-pmap-c)# class dscp26no class dscp24do sh run | b polno class dscp24 no class dscp24  class dscp24  R3(config-pmap-c)#^Z R3#sh *Mar 2 07:30:58.697: %SYS-5-CONFIG_I: Configured from console by console R3#sh pol int s   fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: Prec1 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: precedence 1 Class-map: dscp28 (match-all) 30 packets, 3420 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp24 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) --More--   Class-map: class-default (match-any) 20870 packets, 1973099 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: Prec1 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: precedence 1 Class-map: dscp28 (match-all) 50 packets, 5700 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp24 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) --More--   Class-map: class-default (match-any) 20886 packets, 1974475 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# R3# RACK11AS>c 6 [Resuming connection 6 to r6 ... ] S6(config-if)#mls qos dscp-mutation Prob17nmls qos dscp-mutation Prob17omls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 S6(config-if)#exit S6(config)#no mls qos dsc   S6(config)#no mls qos dsc  S6(config)#no mls qos dscp    map dsc   S6(config)#no mls qos map dscp-m S6(config)#no mls qos map dscp-mutation Prob17 S6(config)#^Z S6# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#mls qoss ^ % Invalid input detected at '^' marker. S5(config)#mls qoss  QoS: ensure flow-control on all interfaces are OFF for proper operation. S5(config)#int fa 0/24 S5(config-if)#mls qos tru dsc S5(config-if)#exit S5(config)#dscp      mls qos map dsc S5(config)#mls qos map dscp-m S5(config)#mls qos map dscp-mutation Prob17 28 to 26 S5(config)#mls qos map dscp-mutation Prob17 28 to 26        14 to 12 S5(config)#int fa 0/244  S5(config-if)# S5(config-if)#mls qos dsc S5(config-if)#mls qos dscp-mutation Prob17 S5(config-if)#^Z S5# RACK11AS>5 [Resuming connection 5 to r5 ... ] 1d07h: %SYS-5-CONFIG_I: Configured from console by console S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#^Z S5#config tping 180.40.7.129 1d07h: %SYS-5-CONFIG_I: Configured from console by console S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: Prec1 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: precedence 1 Class-map: dscp28 (match-all) 50 packets, 5700 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp24 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) --More--   Class-map: class-default (match-any) 21024 packets, 1986139 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | b mls mls qos map dscp-mutation Prob17 14 to 12 mls qos map dscp-mutation Prob17 28 to 26 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport mode dynamic desirable ! interface FastEthernet0/2 --More--   S5#sh run int fa 0/24 Building configuration... Current configuration : 145 bytes ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk mls qos trust dscp mls qos dscp-mutation Prob17 end S5# S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b class class-map match-all dscp26 match dscp af31 class-map match-all dscp24 match dscp cs3 class-map match-all dscp28 match dscp af32 class-map match-all Prec1 match precedence 1 class-map match-all Prec3 match precedence 3 class-map match-all Telnet match protocol telnet class-map match-any FTP match protocol ftp match access-group 103 ! ! policy-map test class Prec1 class dscp28 class dscp26 class dscp24 policy-map Prob9 --More--   R3#[Ash run | b class R3#sh run | b class     pol policy-map test class Prec1 class dscp28 class dscp26 class dscp24 policy-map Prob9 class FTP bandwidth remaining percent 50 class Telnet bandwidth remaining percent 25 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto --More--   vrrp 71 ip 180.40.7.133 --More--   vrrp 71 priority 111 --More--   glbp 71 ip 180.40.7.134 --More--   glbp 71 weighting 100 lower 90 --More--   glbp 71 weighting track 3 decrement 50 --More--   standby 71 ip 180.40.7.132 --More--   standby 71 priority 150 --More--   standby 71 preempt --More--   standby 71 track Serial1/2 51 --More--   standby 71 track 2 decrement 61 --More--   service-policy input test --More--  ! --More--  interface BRI0/0 --More--   no ip address --More--   R3# R3# R3# RACK11AS>76 % 76 is not an open connection RACK11AS> [Resuming connection 3 to r3 ... ] R3#\  RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#do sh run \     | b class class-map match-all S5Other match access-group 1 class-map match-all S5Telnet match access-group 1 match protocol telnet class-map match-any JPG match protocol http mime "*jpeg" match protocol http mime "*jpg" match protocol http mime "*jpe" match protocol http url "*jpe" match protocol http url "*jpg" match protocol http url "*jpeg" ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class JPG shape average 1000000 class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 --More--   R7(config)#class R7(config)#class-map FTP R7(config-cmap)#match pro R7(config-cmap)#match protocol ftp R7(config-cmap)#exit R7(config)#class R7(config)#class-map Telnet R7(config-cmap)#match pro telnet R7(config-cmap)#exit R7(config)#Pol R7(config)#Policy-map Prob18to20 R7(config-pmap)#class R7(config-pmap)#class FTP R7(config-pmap-c)#ban R7(config-pmap-c)#bandwidth re R7(config-pmap-c)#bandwidth remaining p R7(config-pmap-c)#bandwidth remaining percent 25 R7(config-pmap-c)#exit R7(config-pmap)#class Telnet R7(config-pmap-c)#class Telnetexit bandwidth remaining percent 25 R7(config-pmap-c)#exit R7(config-pmap)#class R7(config-pmap)#class class-default R7(config-pmap-c)#class class-defaultexit bandwidth remaining percent 25  50 R7(config-pmap-c)#int fa 0/1 R7(config-if)#do sh run int fa 0/1 Building configuration... Current configuration : 280 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 71 ip 180.40.7.133 glbp 71 ip 180.40.7.134 glbp 71 priority 110 glbp 71 weighting 100 lower 90 standby 71 ip 180.40.7.132 standby 71 preempt service-policy output Prob6 end R7(config-if)#no service-policy output Prob6 R7(config-if)#ser out Prob18to20 R7(config-if)#max R7(config-if)#max-reserved-bandwidth 100 R7(config-if)#^Z R7#sh run | *Mar 1 23:46:30.281: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b class class-map match-all S5Other match access-group 1 class-map match-all Telnet match protocol telnet class-map match-all FTP match protocol ftp class-map match-all S5Telnet match access-group 1 match protocol telnet class-map match-any JPG match protocol http mime "*jpeg" match protocol http mime "*jpg" match protocol http mime "*jpe" match protocol http url "*jpe" match protocol http url "*jpg" match protocol http url "*jpeg" ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class JPG shape average 1000000 --More--   class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 policy-map Prob18to20 class FTP bandwidth remaining percent 25 class Telnet bandwidth remaining percent 25 class class-default bandwidth remaining percent 50 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 --More--   no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 71 ip 180.40.7.133 glbp 71 ip 180.40.7.134 glbp 71 priority 110 glbp 71 weighting 100 lower 90 standby 71 ip 180.40.7.132 standby 71 preempt max-reserved-bandwidth 100 service-policy output Prob18to20 ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast --More--   R7#shj  access-list Standard IP access list 1 10 permit 208.28.1.2 (452 matches) R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#accce  ess-list 100 per ip host 87.23.11.213   123 any R7(config)#access-list 100 per ip host 87.23.11.123 any   ahost 87.23.11.123 nhost 87.23.11.123 yhost 87.23.11.123  host 87.23.11.123  R7(config)#class R7(config)#class-map SQL R7(config-cmap)#match pro R7(config-cmap)#match protocol sq R7(config-cmap)#match protocol sqll  R7(config-cmap)#match protocol sql R7(config-cmap)#match protocol sql` R7(config-cmap)#match protocol sql` ? sqlnet sqlserver R7(config-cmap)#match protocol sqls R7(config-cmap)#match protocol sqlserver R7(config-cmap)#match acc` R7(config-cmap)#match acc` =          do sh ip nbar port sqls port-map sqlserver tcp 1433 R7(config-cmap)#do sh ip nbar port sqls n port-map sqlnet tcp 1521 R7(config-cmap)#match acc R7(config-cmap)#match access-group 100 R7(config-cmap)#esxi   xit R7(config)#pol exitmatch access-group 100do sh ip nbar port sqlnsmatch protocol sqlserver class-map SQL access-list 100 per ip any host 87.23.11.123 host 87.23.11.123 any max-reserved-bandwidth 100 ser out Prob18to20  ^ % Invalid input detected at '^' marker. R7(config)#ser out Prob18to20exit match access-group 100exit ser out Prob18to20 Prob18to20  Prob18to20  Prob18to20 Prob18to20  Prob18to20  Prob18to20  Prob18to20 p Prob18to20o Prob18to20l Prob18to20 R7(config-pmap)#class R7(config-pmap)#class Q SQL R7(config-pmap-c)#pri R7(config-pmap-c)#priority ? <8-2000000> Kilo Bits per second percent % of total bandwidth R7(config-pmap-c)#priority 56 ? <32-2000000> Burst in bytes R7(config-pmap-c)#priority 56 128 R7(config-pmap-c)#^Z R7# *Mar 1 23:51:13.213: %SYS-5-CONFIG_I: Configured from console by console R7#sh polk    int fa 0/0 R7#sh pol int fa 0/0 1 FastEthernet0/1 Service-policy output: Prob18to20 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 --More--   Class-map: SQL (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 100 Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 318 packets, 27507 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Output Queue: Conversation 267 Bandwidth remaining 50 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 245/19922 (depth/total drops/no-buffer drops) 0/0/0 R7#q sh traff R7#sh ru n  n | b class class-map match-all S5Other match access-group 1 class-map match-all Telnet match protocol telnet class-map match-all FTP match protocol ftp class-map match-all S5Telnet match access-group 1 match protocol telnet class-map match-all SQL match protocol sqlserver match access-group 100 class-map match-any JPG match protocol http mime "*jpeg" match protocol http mime "*jpg" match protocol http mime "*jpe" match protocol http url "*jpe" match protocol http url "*jpg" match protocol http url "*jpeg" ! ! policy-map Prob6 class S5Telnet --More--   R7#sh run | b class     pol policy-map Prob6 class S5Telnet bandwidth 1000 class JPG shape average 1000000 class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 policy-map Prob18to20 class FTP bandwidth remaining percent 25 class Telnet bandwidth remaining percent 25 class SQL priority 56 128 class class-default bandwidth remaining percent 50 ! ! ! ! ! --More--   R7#sh run | b access-li access-list 1 permit 208.28.1.2 access-list 100 permit ip host 87.23.11.123 any access-list 100 permit ip any host 87.23.11.123 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! --More--   R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#priority 56 128class SQL pol Prob18to20 R7(config-pmap)#class class-0 deafult % class map class-deafult not configured R7(config-pmap)#class class-deafultfult ult fultault R7(config-pmap-c)#fa R7(config-pmap-c)#fair-queue deconfigure bandwidth before issuing this command in this class R7(config-pmap-c)#no ban R7(config-pmap-c)#no bandwidth re R7(config-pmap-c)#no bandwidth rem R7(config-pmap-c)#no bandwidth rem    R7(config-pmap-c)#no bandwidth fair-queue  R7(config-pmap-c)#do sh pol int fa0/0 R7(config-pmap-c)#do sh pol int fa0/0 1 FastEthernet0/1 Service-policy output: Prob18to20 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 --More--   Class-map: SQL (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 100 Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 620 packets, 53334 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 256 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-pmap-c)#  fa R7(config-pmap-c)#fair-queue ? <16-4096> Number Dynamic Conversation Queues R7(config-pmap-c)#fair-queue 512 R7(config-pmap-c)#fair-queue 512do sh pol int fa0/1 FastEthernet0/1 Service-policy output: Prob18to20 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 521 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 522 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 --More--   Class-map: SQL (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol sqlserver Match: access-group 100 Queueing Strict Priority Output Queue: Conversation 520 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 639 packets, 55181 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 512 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-pmap-c)#^Z R7#sh *Mar 1 23:57:59.154: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b pol policy-map Prob6 class S5Telnet bandwidth 1000 class JPG shape average 1000000 class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 policy-map Prob18to20 class FTP bandwidth remaining percent 25 class Telnet bandwidth remaining percent 25 class SQL priority 56 128 class class-default fair-queue 512 ! ! ! ! ! --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#class R7(config)#class-map ts est R7(config-cmap)#match ip R7(config-cmap)#match ip ? dscp Match IP DSCP (DiffServ CodePoints) precedence Match IP precedence rtp Match RTP port nos R7(config-cmap)#match ip pre ? <0-7> Enter up to 4 precedence values separated by white-spaces critical Match packets with critical precedence (5) flash Match packets with flash precedence (3) flash-override Match packets with flash override precedence (4) immediate Match packets with immediate precedence (2) internet Match packets with internetwork control precedence (6) network Match packets with network control precedence (7) priority Match packets with priority precedence (1) routine Match packets with routine precedence (0) R7(config-cmap)#match ip pre              exit R7(config)#exitclass-map test nclass-map test oclass-map test  class-map test  R7(config)#pol Prob20and21      1  and22 R7(config-pmap)#class FTP R7(config-pmap-c)#pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 256000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 256000 con R7(config-pmap-c)#police 256000 conform-action ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#police 256000 conform-action tra ? exceed-action action when rate is within conform and conform + exceed burst R7(config-pmap-c)#police 256000 conform-action tra ex R7(config-pmap-c)#police 256000 conform-action tra exceed-action drop R7(config-pmap-c-police)#exit R7(config-pmap-c)#exit R7(config-pmap)#class Telnet R7(config-pmap-c)#pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 56000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 1400 ? <1000-512000000> Burst bytes be Excess burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 1400 3500 ? conform-action action when rate is less than conform burst R7(config-pmap-c)#police 56000 1400 3500 con R7(config-pmap-c)#police 56000 1400 3500 conform-action se R7(config-pmap-c)#police 56000 1400 3500 conform-action set-p R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 ? exceed-action action when rate is within conform and conform + exceed burst R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 e$0 1400 3500 conform-action set-prec-transmit 1 ex  R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action s R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action set-t R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action set-t p R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 ? violate-action action when rate is greater than conform + exceed burst R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 vi R7(config-pmap-c)#$smit 1 exceed-action set-prec-transmit 0 violate-action dr R7(config-pmap-c)#$eed-action set-prec-transmit 0 violate-action drop R7(config-pmap-c-police)#exit R7(config-pmap-c)#exit R7(config-pmap)#class class-defaul;tr     ult R7(config-pmap-c)#fa R7(config-pmap-c)#fair-queue R7(config-pmap-c)#qu R7(config-pmap-c)#queue-limit 100 R7(config-pmap-c)#int s 1/0.1 R7(config-subif)#ser R7(config-subif)#service-policy q out Prob21and22 CBWFQ : Not supported on subinterfaces R7(config-subif)#exit R7(config)#map R7(config)#map-cl R7(config)#map-class fram` R7(config)#map-class fram`  R7(config)#map-class frame-relay Prob21and22 R7(config-map-class)#ser R7(config-map-class)#service-policy Pr    out Prob21and22 R7(config-map-class)#intservice-policy out Prob21and22map-class frame-relay Prob21and22exit service-policy out Prob21and22int s 1/0.1  R7(config-subif)#fram   R7(config-subif)#frame-relay c lass       lass Prob1 21and22 R7(config-subif)#do sh pol int s 1/. 0.1 R7(config-subif)#do sh pol int s 1/0.1 R7(config-subif)#do sh pol int s 1/0.1 R7(config-subif)#do sh pol int s 1/0.1 R7(config-subif)#do sh pol int s 1/0.1 R7(config-subif)#do sh pol int s 1/0.1 R7(config-subif)#exit R7(config)#int s 1/0 R7(config-if)#fram traff R7(config-if)#fram traffint s 1/0 exit do sh pol int s 1/0.1 Serial1/0.1: DLCI 703 - Service-policy output: Prob21and22 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp police: cir 256000 bps, bc 8000 bytes conformed 0 packets, 0 bytes; actions: transmit exceeded 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet police: cir 56000 bps, bc 1400 bytes, be 3500 bytes conformed 0 packets, 0 bytes; actions: --More--   set-prec-transmit 1 exceeded 0 packets, 0 bytes; actions: set-prec-transmit 0 violated 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps, violate 0 bps Class-map: class-default (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 16 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-if)#^Z R7#sh *Mar 2 00:05:42.902: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b pol policy-map Prob6 class S5Telnet bandwidth 1000 class JPG shape average 1000000 class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 policy-map Prob18to20 class FTP bandwidth remaining percent 25 class Telnet bandwidth remaining percent 25 class SQL priority 56 128 class class-default fair-queue 512 policy-map Prob21and22 class FTP police 256000 conform-action transmit exceed-action drop class Telnet police 56000 1400 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop --More--   class class-default fair-queue queue-limit 100 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 71 ip 180.40.7.133 --More--   glbp 71 ip 180.40.7.134 glbp 71 priority 110 glbp 71 weighting 100 lower 90 standby 71 ip 180.40.7.132 standby 71 preempt max-reserved-bandwidth 100 service-policy output Prob18to20 ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay class Prob21and22 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point --More--   ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 --More--   no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server ! ! map-class frame-relay Prob7 frame-relay priority-group 1 --More--  ! map-class frame-relay Prob21and22 service-policy output Prob21and22 access-list 1 permit 208.28.1.2 access-list 100 permit ip host 87.23.11.123 any access-list 100 permit ip any host 87.23.11.123 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 --More--   R7#sh traff Interface Se1/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 701 56000 875 7000 0 125 875 - Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 703 56000 875 7000 0 125 875 - Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 702 56000 875 7000 0 125 875 - R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pol p Prb21and22ob21and22 R7(config-pmap)#class R7(config-pmap)#class class R7(config-pmap)#class class-dea fault R7(config-pmap-c)#pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 512000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 512000 8000 1375 con R7(config-pmap-c)#police 512000 8000 1375 conform-action tra R7(config-pmap-c)#police 512000 8000 1375 conform-action transmit ex R7(config-pmap-c)#$00 8000 1375 conform-action transmit exceed-action tr R7(config-pmap-c)#$75 conform-action transmit exceed-action transmit vi R7(config-pmap-c)#$-action transmit exceed-action transmit violate-action droansmit exceed-action transmit violate-action drop  R7(config-pmap-c-police)#exit R7(config-pmap-c)#exi R7(config-pmap)#exit R7(config)#map   R7(config)#map-c R7(config)#map-class fram Prob21and22 R7(config-map-class)#fram cir ? <1-45000000> Applied to both Incoming/Outgoing CIR, Bits per second in Incoming CIR out Outgoing CIR R7(config-map-class)#fram cir 600000 R7(config-map-class)#^Z R7# *Mar 2 00:11:47.881: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b pol policy-map Prob6 class S5Telnet bandwidth 1000 class JPG shape average 1000000 class S5Other police cir 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 policy-map Prob18to20 class FTP bandwidth remaining percent 25 class Telnet bandwidth remaining percent 25 class SQL priority 56 128 class class-default fair-queue 512 policy-map Prob21and22 class FTP police 256000 conform-action transmit exceed-action drop class Telnet police 56000 1400 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop --More--   class class-default fair-queue queue-limit 100 police 512000 8000 1375 conform-action transmit exceed-action transmit violate-action drop ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto --More--   half-duplex vrrp 71 ip 180.40.7.133 glbp 71 ip 180.40.7.134 glbp 71 priority 110 glbp 71 weighting 100 lower 90 standby 71 ip 180.40.7.132 standby 71 preempt max-reserved-bandwidth 100 service-policy output Prob18to20 ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay class Prob21and22 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive --More--  ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown --More--  ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server ! ! --More--  map-class frame-relay Prob7 frame-relay priority-group 1 ! map-class frame-relay Prob21and22 frame-relay cir 600000 service-policy output Prob21and22 access-list 1 permit 208.28.1.2 access-list 100 permit ip host 87.23.11.123 any access-list 100 permit ip any host 87.23.11.123 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous --More--   R7# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh run int s 1/0.1 Building configuration... Current configuration : 166 bytes ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 203 end R2#sh run int s 1/0.1 2 Building configuration... Current configuration : 200 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob4b end R2#configt Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#sh run | b map-class ^ % Invalid input detected at '^' marker. R2(config)#sh run | b map-classdsh run | b map-classosh run | b map-class sh run | b map-class map-class frame-relay Prob4b frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn access-list 100 deny ospf any any access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login --More--   R2(config)#map-class fram Prob23and24 R2(config-map-class)#fram cir 64000 R2(config-map-class)#fra ad R2(config-map-class)#fra adaptive-shaping be R2(config-map-class)#fra adaptive-shaping becn R2(config-map-class)#fram ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 7000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R2(config-map-class)#fram      int s 1/0/.  .1 R2(config-subif)#fram   class Prob23and24 R2(config-subif)#^Z R2#sh *Mar 2 08:12:26.415: %SYS-5-CONFIG_I: Configured from console by console R2#sh traff Interface Se1/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 201 56000 875 7000 0 125 875 - Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 203 64000 1000 64000 0 125 1000 BECN Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 207 64000 5000 64000 32000 125 1000 BECN R2#] sh run I | b interface Serial1/0 interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay class Prob23and24 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob4b ! interface Serial1/1 no ip address shutdown --More--  ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address --More--   shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server ! ! map-class frame-relay Prob4b frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn ! map-class frame-relay Prob23and24 frame-relay cir 64000 frame-relay adaptive-shaping becn access-list 100 deny ospf any any access-list 100 permit ip any any --More--  ! --More--  ! --More--  ! --More--   R2#sh int s 1/2 Serial1/2 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is 180.40.7.2/27 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input 00:00:01, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 25896 packets input, 2016444 bytes, 0 no buffer Received 13521 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 25845 packets output, 2009381 bytes, 0 underruns 0 output errors, 0 collisions, 5 interface resets 0 output buffer failures, 0 output buffers swapped out --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#encap       shut R2(config-if)#eca *Mar 2 08:15:45.614: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-if)#ecan    *Mar 2 08:15:47.617: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 2 08:15:48.618: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R2(config-if)#ena ppp ^ % Invalid input detected at '^' marker. R2(config-if)#ena ppp ppp c pppa pppp ppp R2(config-if)#ppp ? accm Set initial Async Control Character Map accounting Set PPP network accounting method acfc Options for HDLC Address & Control Field Compression authentication Set PPP link authentication method authorization Set PPP network authorization method bridge Enable PPP bridge translation caller Caller option when no CLID is available chap Set CHAP authentication parameters direction Override default PPP direction dnis Authentication via DNIS before LCP eap Set EAP authentication parameters encrypt Enable PPP encryption ipcp Set IPCP negotiation options iphc Set IPCP Header Compression control options lcp PPP LCP configuration link Set miscellaneous link parameters loopback PPP loopback options max-bad-auth Allow multiple authentication failures max-configure Number of conf-reqs sent before assuming peer is unable to respond max-failure Number of conf-naks sent before assuming configuration is not converging --More--   max-terminate Number of term-reqs sent before assuming peer is unable to respond ms-chap Set MS-CHAP authentication parameters ms-chap-v2 Set MS-CHAP-V2 authentication parameters multilink Make interface multilink capable pap Set PAP authentication parameters pfc Options for Protocol Field Compression quality Set parameters related to Link Quality Monitoring (LQM) reliable-link Use LAPB with PPP to provide a reliable link timeout Set PPP timeout parameters R2(config-if)#ppp mu R2(config-if)#ppp multilink ? endpoint Configure the local Endpoint Discriminator group Put interface in a multilink bundle multiclass Configure support for Multiclass Multilink queue Specify link queuing parameters R2(config-if)#ppp multilink R2(config-if)#ppp multilink gr R2(config-if)#ppp multilink group ? <1-2147483647> Multilink group number R2(config-if)#ppp multilink group 1 % Cannot set multilink group. Interface Multilink1 does not exist R2(config-if)#exit R2(config)#int mku R2(config)#int mku  u R2(config)#int multilink 1 R2(config-if)# *Mar 2 08:16:36.709: %LINEPROTO-5-UPDOWN: Line protocol on Interface Multilink1, changed state to down R2(config-if)#int s 1/2 R2(config-if)#int s 1/2multilink 1 R2(config-if)#exi int multilink 1s 1/2 multilink 1 R2(config-if)#ppp mu R2(config-if)#ppp multilink ? fragment Specify fragmentation parameters group Put interface in a multilink bundle idle-link Do not transmit fragments over the lowest speed link interleave Allow interleaving of small packets with fragments links Specify the limits on the number of links in a bundle load-threshold Specify threshold used to add/delete links slippage Set constraints on amount of data the MLP reassembly engine will buffer per link R2(config-if)#ppp multilink fra R2(config-if)#ppp multilink fragment ? delay Specify the maximum delay for each fragment disable Suppress multilink fragmentation when possible maximum Specify the maximum number of fragments per transmitted packet R2(config-if)#ppp multilink fragment m R2(config-if)#ppp multilink fragment maximum ? <2-16> Maximum fragments per packet R2(config-if)#ppp multilink fragment maximum         del R2(config-if)#ppp multilink fragment delay ? <1-1000> Maximum delay in milliseconds R2(config-if)#ppp multilink fragment delay 15 R2(config-if)#ppp multilink fragment delay 15                 in R2(config-if)#ppp multilink interleave R2(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 128 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 encapsulation ppp shutdown clock rate 64000 ppp multilink end R2(config-if)#ip address 180.40.7.2 255.255.255.224 R2(config-if)#int s 1/2 R2(config-if)#no ip address 180.40.7.2 255.255.255.224 R2(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] *M R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int mul 1 R3(config-if)#ppp *Mar 2 08:20:33.930: %LINEPROTO-5-UPDOWN: Line protocol on Interface Multilink1, changed state to down R3(config-if)#ppp mul fra de 15 R3(config-if)#ppp mul int R3(config-if)#do sh run int s 1/2 Building configuration... Current configuration : 123 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 end R3(config-if)# ip address 180.40.7.1 255.255.255.224 R3(config-if)# max-reserved-bandwidth 100 R3(config-if)# service-policy output Prob9 R3(config-if)#int s 1/0 2 R3(config-if)#no ip address 180.40.7.1 255.255.255.224 R3(config-if)#no max-reserved-bandwidth 100 R3(config-if)#no service-policy output Prob9 R3(config-if)#exsi  it R3(config)#do sh run | b route-map ip policy route-map Prob1 duplex auto speed auto vrrp 71 ip 180.40.7.133 vrrp 71 priority 111 glbp 71 ip 180.40.7.134 glbp 71 weighting 100 lower 90 glbp 71 weighting track 3 decrement 50 standby 71 ip 180.40.7.132 standby 71 priority 150 standby 71 preempt standby 71 track Serial1/2 51 standby 71 track 2 decrement 61 service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto --More--   speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address --More--   shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server ! --More--  access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo-reply access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo-reply access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo-reply access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo access-list 103 permit tcp any any eq ftp-data access-list 103 permit tcp any eq ftp-data any queue-list 1 protocol ip 1 tcp ftp queue-list 1 protocol ip 1 tcp ftp-data queue-list 1 protocol ip 2 tcp telnet queue-list 1 default 3 queue-list 1 queue 1 byte-count 2673 queue-list 1 queue 2 byte-count 1309 queue-list 1 queue 3 byte-count 1294 ! route-map Prob1 permit 10 match ip address 102 match length 1001 2147483647 set interface Serial1/2 ! route-map Prob1 permit 20 match ip address 100 --More--   set ip next-hop 180.40.7.67 --More--  ! --More--  route-map Prob1 permit 30 --More--   match ip address 101 --More--   set ip next-hop 180.40.7.2 --More--  ! --More--   R3(config)#route-map Prob1 permit 10 R3(config-route-map)#no set interface Serial1/2 R3(config-route-map)# set ip next-hop 180.40.7.2 R3(config-route-map)#^Z R3# *Mar 2 08:22:18.189: %SYS-5-CONFIG_I: Configured from console by console R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# set ip next-hop 180.40.7.2no set interface Serial1/2route-map Prob1 permit 10  R3(config-route-map)#route-map Prob1 permit 10 set ip next-hop 180.40.7.2route-map Prob1 permit 10  set ip next-hop 180.40.7.2n set ip next-hop 180.40.7.2o set ip next-hop 180.40.7.2 set ip next-hop 180.40.7.2 R3(config-route-map)#set int mul f1 ^ % Invalid input detected at '^' marker. R3(config-route-map)#set int mul f11  R3(config-route-map)#^Z R3# *Mar 2 08:22:37.260: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | n   b inter interface Multilink1 ip address 180.40.7.1 255.255.255.224 ppp multilink ppp multilink fragment delay 15 ppp multilink interleave ppp multilink group 1 max-reserved-bandwidth 100 service-policy output Prob9 ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 71 ip 180.40.7.133 vrrp 71 priority 111 glbp 71 ip 180.40.7.134 glbp 71 weighting 100 lower 90 glbp 71 weighting track 3 decrement 50 standby 71 ip 180.40.7.132 standby 71 priority 150 standby 71 preempt standby 71 track Serial1/2 51 --More--   standby 71 track 2 decrement 61 service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address --More--   shutdown ! interface Serial1/2 no ip address ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#encap ppp R3(config-if)#ppp m,ul     uk 1 ^ % Invalid input detected at '^' marker. R3(config-if)#ppp muk 1k 1 l 1 ^ % Invalid input detected at '^' marker. R3(config-if)#ppp mul 1 gr 1` ^ % Invalid input detected at '^' marker. R3(config-if)#ppp mul gr 1`  R3(config-if)#^Z R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#int s 1/2 R2(config-if)#mpo   nmo  o shut R2(config-if)#^Z R2# *Mar 2 08:23:44.254: %SYS-5-CONFIG_I: Configured from console by console R2# *Mar 2 08:23:46.065: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 2 08:23:46.121: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up R2# *Mar 2 08:23:47.111: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up *Mar 2 08:23:47.123: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] *M R3#deb ppp mu fra R3#deb ppp mu fragments ? R3#deb ppp mu fragments Multilink fragments debugging is on R3# *Mar 2 08:24:32.641: Se1/2 MLP: O frag C0000008 size 86 encsize 4 *Mar 2 08:24:33.619: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.129 YES manual up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 180.40.7.66 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 unassigned YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--  Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down Multilink1 180.40.7.1 YES manual up up R3# *Mar 2 08:24:42.646: Se1/2 MLP: O frag C0000009 size 86 encsize 4 *Mar 2 08:24:43.619: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3#ping 180.40.7  *Mar 2 08:24:52.646: Se1/2 MLP: O frag C000000A size 86 encsize 4 *Mar 2 08:24:53.620: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3#ping 180.40.             RACK11AS>4 [Resuming connection 4 to r4 ... ] * R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip add dhcp cli fa 0/0  nt fa 0/0 do deb dhcp deu all no shutshut int fa 0/0no shut shut int fa 0/0p add dhcp cli fa 0/0 nt fa 0/0 p add dhcpnt fa 0/0 no ip local pol rout Prob3no ip local pol rout Prob3  ip local pol rout Prob3  R4(config)#^Z R4# *Mar 2 08:27:41.071: %SYS-5-CONFIG_I: Configured from console by console R4#ping ip Target IP address: 20.10.1.2 Repeat count [5]: Datagram size [100]: 15000  Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 5, 1500-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: !! RACK11AS>c3 [confirm] [OK] RACK11AS>r2 3  disc 3 Closing connection to r3 [confirm] RACK11AS>r3 Translating "r3" Trying R3 (1.1.1.1, 2003)... Open ************************************************************** Global Knowledge Hands-On Labs Access Server Access is restricted to Global Knowledge CCIE Students ************************************************************** Please re-enter your password. (This is the same password you used to log onto the Lab website.) If you see a username prompt, please wait 40 seconds and try again. If the username prompt persists, please reset equipment from your "Pod x" link. User Access Verification Password: Password OK *Mar 2 08:25:42.648: Se1/2 MLP: O frag C000000F size 86 encsize 4 *Mar 2 08:25:43.622: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3# R3#sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 532 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 484 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 153 message lines logged --More--   Log Buffer (4096 bytes): cess 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 06:33:39.403: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired *Mar 2 06:33:51.751: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 06:47:46.556: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Active -> Speak *Mar 2 06:48:01.564: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Active *Mar 2 06:55:52.909: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 71 Fwd 2 state Listen -> Active *Mar 2 07:02:01.834: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Active -> Speak *Mar 2 07:07:26. *Mar 2 08:25:52.649: Se1/2 MLP: O frag C0000010 size 86 encsize 4 *Mar 2 08:25:53.622: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 935: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Active *Mar 2 07:07:27.039: %GLBP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Active *Mar 2 07:07:27.039: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 71 Fwd 1 state Listen -> Active *Mar 2 07:07:52.581: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired --More--  *Mar 2 07:08:39.878: %SYS-5-CONFIG_I: Configured from console by console *Mar 2 07:09:04.827: %GLBP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Active -> Speak *Mar 2 07:09:04.827: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 71 Fwd 1 state Active -> Listen *Mar 2 07:09:05.809: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Active -> Speak *Mar 2 07:09:22.280: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 07:12:32.876: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Active *Mar 2 07:23:28.647: %SYS-5-CONFIG_I: Configured from console by console *Mar 2 07:30:58.697: %SYS-5-CONFIG_I: Configured from console by console *Mar 2 08:15:43.947: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Active -> Speak *Mar 2 08:15:44.091: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down *Mar 2 08:15:44.091: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 08:15:45.093: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down *Mar 2 08:20:33.930: %LINEPROTO-5-UPDOWN: Line protocol on Interface Multilink1, changed state to down *Mar 2 08:22:18.189: %SYS-5-CONFIG_I: Configured from console by console --More--  *Mar 2 08:22:37.260: %SYS-5-CONFIG_I: Configured from console by console *Mar 2 08:23:31.101: %SYS-5-CONFIG_I: Configured from console by console *Mar 2 08:23:42.547: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 2 08:23:42.603: %LINK-3-UPDOWN: Interface Multilink1, changed state to up *Mar 2 08:23:43.589: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up *Mar 2 08:23:43.605: %LINEPROTO-5-UPDOWN: Line protocol on Interface Multilink1, changed state to up *Mar 2 08:23:44.094: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 71 state Standby -> Active *Mar 2 08:24:32.641: Se1/2 MLP: O frag C0000008 size 86 encsize 4 *Mar 2 08:24:33.619: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 *Mar 2 08:24:42.646: Se1/2 MLP: O frag C0000009 size 86 encsize 4 *Mar 2 08:24:43.619: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 *Mar 2 08:24:52.646: Se1/2 MLP: O frag C000000A size 86 encsize 4 *Mar 2 08:24:53.620: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 *Mar 2 08:25:02.647: Se1/2 MLP: O frag C000000B size 86 encsize 4 *Mar 2 08:25:03.620: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 *Mar 2 08:25:12.647: Se1/2 MLP: O frag C000000C size 86 encsize 4 *Mar 2 08:25:13.621: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 *Mar 2 08:25:22.647: Se1/2 MLP: O frag C000000D size 86 encsize 4 *Mar 2 08:25:23.621: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 *Mar 2 08:25:32.648: Se1/2 MLP: O frag C000000E size 86 encsize 4 --More--  *Mar 2 08:25:33.621: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 *Mar 2 08:25:42.648: Se1/2 MLP: O frag C000000F size 86 encsize 4 *Mar 2 08:25:43.622: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3#     *Mar 2 08:26:02.649: Se1/2 MLP: O frag C0000011 size 86 encsize 4 *Mar 2 08:26:03.623: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3#clea log Clear logging buffer [confirm] R3# R3# R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] !! R4#150020.10.1.2 ping ip config tping ip  Target IP address: % Bad IP address R4#ping ip Target IP address: ping ip1500 20.10.1.2 Repeat count [5]: 20.10.1.2   Datagram size [100]: 20.10.1.2 ping ip 1500  Timeout in seconds [2]: Extended commands [n]: y Source address or interface: 100.1.1.1 Type of service [0]: Set DF bit in IP header? [no]: Validate reply data? [no]: Data pattern [0xABCD]: Loose, Strict, Record, Timestamp, Verbose[none]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 5, 1500-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!! RACK11AS>3 [Resuming connection 3 to r3 ... ] * *Mar 2 08:26:34.702: Se1/2 MLP: O frag 00000025 size 240 encsize 4 *Mar 2 08:26:34.762: Se1/2 MLP: O frag 00000026 size 240 encsize 4 via oqueue *Mar 2 08:26:34.794: Se1/2 MLP: O frag 00000027 size 240 encsize 4 via oqueue *Mar 2 08:26:34.826: Se1/2 MLP: O frag 00000028 size 240 encsize 4 via oqueue *Mar 2 08:26:34.854: Se1/2 MLP: O frag 40000029 size 118 encsize 4 via oqueue *Mar 2 08:26:35.287: Se1/2 MLP: O frag 8000002A size 240 encsize 4 *Mar 2 08:26:35.287: Se1/2 MLP: O frag 0000002B size 240 encsize 4 *Mar 2 08:26:35.287: Se1/2 MLP: O frag 0000002C size 240 encsize 4 *Mar 2 08:26:35.347: Se1/2 MLP: O frag 0000002D size 240 encsize 4 via oqueue *Mar 2 08:26:35.379: Se1/2 MLP: O frag 0000002E size 240 encsize 4 via oqueue *Mar 2 08:26:35.411: Se1/2 MLP: O frag 0000002F size 240 encsize 4 via oqueue *Mar 2 08:26:35. R3# R3#439: Se1/2 MLP: O frag 40000030 size 118 encsize 4 via oqueue *Mar 2 08:26:35.871: Se1/2 MLP: O frag 80000031 size 240 encsize 4 *Mar 2 08:26:35.871: Se1/2 MLP: O frag 00000032 size 240 encsize 4 *Mar 2 08:26:35.871: Se1/2 MLP: O frag 00000033 size 240 encsize 4 *Mar 2 08:26:35.932: Se1/2 MLP: O frag 00000034 size 240 encsize 4 via oqueue *Mar 2 08:26:35.964: Se1/2 MLP: O frag 00000035 size 240 encsize 4 via oqueue *Mar 2 08:26:35.996: Se1/2 MLP: O frag 00000036 size 240 encsize 4 via oqueue *Mar 2 08:26:36.024: Se1/2 MLP: O frag 40000037 size 118 encsize 4 via oqueue R3# *Mar 2 08:26:42.651: Se1/2 MLP: O frag C0000038 size 86 encsize 4 *Mar 2 08:26:43.624: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3# *Mar 2 08:26:52.651: Se1/2 MLP: O frag C0000039 size 86 encsize 4 *Mar 2 08:26:53.625: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3# *Mar 2 08:27:02.651: Se1/2 MLP: O frag C000003A size 86 encsize 4 *Mar 2 08:27:03.621: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3# *Mar 2 08:27:12.652: Se1/2 MLP: O frag C000003B size 86 encsize 4 via oqueue *Mar 2 08:27:13.625: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3#u akl   *Mar 2 08:27:22.652: Se1/2 MLP: O frag C000003C size 86 encsize 4 *Mar 2 08:27:23.626: Se1/2 MLP: I ppp IP (0021) size 84 encsize 4 R3#u all All possible debugging has been turned off R3#sh run         RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | n   b int interface Multilink1 ip address 180.40.7.2 255.255.255.224 ppp multilink ppp multilink fragment delay 15 ppp multilink interleave ppp multilink group 1 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto ! --More--  interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay class Prob23and24 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob4b ! interface Serial1/1 no ip address shutdown --More--  ! interface Serial1/2 no ip address encapsulation ppp clock rate 64000 ppp multilink ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! --More--   R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ru | b m   int % Ambiguous command: "sh ru " R3#sh ru | b intrun | b int interface Multilink1 ip address 180.40.7.1 255.255.255.224 ppp multilink ppp multilink fragment delay 15 ppp multilink interleave ppp multilink group 1 max-reserved-bandwidth 100 service-policy output Prob9 ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 71 ip 180.40.7.133 vrrp 71 priority 111 glbp 71 ip 180.40.7.134 glbp 71 weighting 100 lower 90 glbp 71 weighting track 3 decrement 50 standby 71 ip 180.40.7.132 standby 71 priority 150 standby 71 preempt standby 71 track Serial1/2 51 --More--   standby 71 track 2 decrement 61 service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address --More--   shutdown ! interface Serial1/2 no ip address encapsulation ppp ppp multilink ppp multilink group 1 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown --More--   R3#