=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.07.14 08:08:07 =~=~=~=~=~=~=~=~=~=~=~= do sh ip  v int brie Ethernet0/0 [up/up] unassigned Serial0/0 [administratively down/down] unassigned Ethernet0/1 [up/up] FE80::2D0:BBFF:FEE9:6061 2005:0:104:0:2D0:BBFF:FEE9:6061 Serial0/1 [up/up] FE80::2D0:BBFF:FEE9:6060 2005:0:102:0:2D0:BBFF:FEE9:6060 Loopback1 [up/up] FE80::2D0:BBFF:FEE9:6060 2001:1:1::1 Tunnel0 [up/up] FE80::B428:742 2002:B428:742:: R1(config)#int lo 99 R1(config-if)#ipv add 2006:1:1::/128 R1(config-if)#^Z R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipv pre R2(config)#ipv prefix-list noloop den 2006:2:2::/128 R2(config)#ipv prefix-list noloop den 2006:2:2::/128                  per ::/0 le 128 R2(config)#router        ipv router ospf 1 R2(config-rtr)#re  dis R2(config-rtr)#distuer R2(config-rtr)#distuer    R2(config-rtr)#distr R2(config-rtr)#distribute-list p R2(config-rtr)#distribute-list prefix-list noloop out c on   on R2(config-rtr)#distribute-list prefix-list noloop out connected R2(config-rtr)#distribute-list prefix-list noloop out connected ipv router ospf 1 distribute-list prefix-list noloop out connected  ipv router rip R2RnIP R2(config-rtr)#ipv router rip R2RnIPnipv router rip R2RnIPoipv router rip R2RnIP ipv router rip R2RnIP R2(config)#ipv router rip R2RIP R2(config-rtr)#disd tr R2(config-rtr)#distribute-list p R2(config-rtr)#distribute-list prefix-list ipv router rip R2RIP no ipv router rip R2RnIPipv router rip R2RnIP distribute-list prefix-list noloop out connected ^ % Invalid input detected at '^' marker. R2(config-rtr)#distribute-list prefix-list noloop out connected            R2(config-rtr)#exit R2(config)#in t  t lo 99 R2(config-if)#ipv add 2006:2:2::/128 R2(config-if)#^Z R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#confi gt ^ % Invalid input detected at '^' marker. R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int lo 99 R3(config-if)#ipv add 2006:3:3::/128 R3(config-if)#^Z R3# *Mar 1 20:47:25.756: %SYS-5-CONFIG_I: Configured from console by console R3#x  RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo 99 R4(config-if)#ipv add 2006:4:4::/129 8 R4(config-if)#^Z R4# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int lo 99 R7(config-if)#ipv add 200           do sh ipv intt    brie FastEthernet0/0 [administratively down/down] unassigned BRI0/0 [administratively down/down] unassigned BRI0/0:1 [administratively down/down] unassigned BRI0/0:2 [administratively down/down] unassigned FastEthernet0/1 [up/up] unassigned Serial1/0 [up/up] unassigned Serial1/0.1 [up/up] FE80::212:7FFF:FE80:F380 2005:0:237:0:212:7FFF:FE80:F380 Serial1/0.2 [up/up] FE80::212:7FFF:FE80:F380 2005:0:702:0:212:7FFF:FE80:F380 Serial1/1 [administratively down/down] unassigned Serial1/2 [administratively down/down] unassigned Serial1/3 [administratively down/down] --More--   unassigned Serial1/4 [administratively down/down] unassigned Serial1/5 [administratively down/down] unassigned Serial1/6 [administratively down/down] unassigned Serial1/7 [administratively down/down] unassigned Loopback1 [up/up] FE80::212:7FFF:FE80:F380 2007:7:7::7 Loopback99 [up/up] unassigned Tunnel0 [up/up] FE80::B428:701 2002:B428:701:: R7(config-if)#ipv add 2006:7:7::/128 R7(config-if)#^Z R7#wr Building configuration... RACK9AS>1 [Resuming connection 1 to r1 ... ] *M R1#wr Building configuration... RACK9AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 R2#wr Building configuration... RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#wr Building configuration... RACK9AS>4 [Resuming connection 4 to r4 ... ] * R4#wr Building configuration... [OK] R4# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#configt Translating "configt" Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#router bgp 100 R7(config-router)#bgp rout R7(config-router)#bgp router-id 7.7.7.7 R7(config-router)#i add R7(config-router)#address-family ip R7(config-router)#address-family ipv6 R7(config-router-af)#net 2006:7:7::128/128 R7(config-router-af)#nei 2000:3:3:: remote   R7(config-router-af)#nei 2000:3:3:: remote-as 10e0 ^ % Invalid input detected at '^' marker. R7(config-router-af)#nei 2000:3:3:: remote-as 10e0  0 R7(config-router-af)#nei      RACK9AS>1 [Resuming connection 1 to r1 ... ] [OK] R1#sh ipv int brie Ethernet0/0 [up/up] unassigned Serial0/0 [administratively down/down] unassigned Ethernet0/1 [up/up] FE80::2D0:BBFF:FEE9:6061 2005:0:104:0:2D0:BBFF:FEE9:6061 Serial0/1 [up/up] FE80::2D0:BBFF:FEE9:6060 2005:0:102:0:2D0:BBFF:FEE9:6060 Loopback1 [up/up] FE80::2D0:BBFF:FEE9:6060 2001:1:1::1 Loopback99 [up/up] FE80::2D0:BBFF:FEE9:6060 2006:1:1:: Tunnel0 [up/up] FE80::B428:742 2002:B428:742:: R1# R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7(config-router-af)# R7(config-router-af)#nei 2002:B428:742:: % Incomplete command. R7(config-router-af)#nei 2002:B428:742:: er  remote R7(config-router-af)#nei 2002:B428:742:: remote-as 200 R7(config-router-af)#^Z R7#sh run | *Mar 1 20:52:26.953: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b router router rip version 2 network 180.40.0.0 no auto-summary ! router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3:: remote-as 100 no neighbor 2000:3:3:: activate neighbor 2002:B428:742:: remote-as 200 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3:: activate neighbor 2002:B428:742:: activate network 2006:7:7::/128 exit-address-family ! ip classless ! --More--   R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#con    RACK9AS> [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router bgp k200    200 R1(config-router)#bgp rout R1(config-router)#bgp router-id 1.1.1.1 R1(config-router)#ad R1(config-router)#address-family i R1(config-router)#address-family ipv6 R1(config-router-af)#net 2006:1:1::/128 R1(config-router-af)#nei vate % Incomplete command. R1(config-router-af)# neighbor 2002:B428:742:: activate % Cannot configure the local system as neighbor R1(config-router-af)# network 2006:7:7::/128 R1(config-router-af)#nei 2002:b428:701:: remote 100 R1(config-router-af)#nei 2005:0:104:0:230:85FF:FEF3:7040 remote 300 R1(config-router-af)#nei 2005:0:102:0:212:7FFF:FE8E:B640 remote 100 R1(config-router-af)#^Z R1#sh *Mar 1 20:55:42.114: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b bgp router bgp 200 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes neighbor 2002:B428:701:: remote-as 100 no neighbor 2002:B428:701:: activate neighbor 2005:0:102:0:212:7FFF:FE8E:B640 remote-as 100 no neighbor 2005:0:102:0:212:7FFF:FE8E:B640 activate neighbor 2005:0:104:0:230:85FF:FEF3:7040 remote-as 300 no neighbor 2005:0:104:0:230:85FF:FEF3:7040 activate no auto-summary ! address-family ipv6 neighbor 2002:B428:701:: activate neighbor 2005:0:102:0:212:7FFF:FE8E:B640 activate neighbor 2005:0:104:0:230:85FF:FEF3:7040 activate network 2006:1:1::/128 network 2006:7:7::/128 exit-address-family ! no ip http server ip classless ! --More--   R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int   router bgp 200 R1(config-router)#add R1(config-router)#address-family i R1(config-router)#address-family ipv6 R1(config-router-af)#nop    network 2006:7:7::/128 R1(config-router-af)#^Z R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3:: remote-as 100 no neighbor 2000:3:3:: activate neighbor 2002:B428:742:: remote-as 200 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3:: activate neighbor 2002:B428:742:: activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 route 2001:1:1::1/128 2002:B428:742:: ipv6 route 2002::/16 Tunnel0 --More--   R7# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router bgp 300 R4(config-router)#bgp route R4(config-router)#bgp router-id 4.4.4.4 R4(config-router)#ad R4(config-router)#address-family i R4(config-router)#address-family ipv6 R4(config-router-af)#net 2006:4:4::/128 R4(config-router-af)#nei 2005:0:104:0:2D0:BBFF:FEE9:6061 remote 200 R4(config-router-af)#^Z R4#sh run *Mar 1 20:58:53.390: %SYS-5-CONFIG_I: Configured from console by console R4#sh run | b bgp router bgp 300 no synchronization bgp router-id 4.4.4.4 bgp log-neighbor-changes neighbor 2005:0:104:0:2D0:BBFF:FEE9:6061 remote-as 200 no neighbor 2005:0:104:0:2D0:BBFF:FEE9:6061 activate no auto-summary ! address-family ipv6 neighbor 2005:0:104:0:2D0:BBFF:FEE9:6061 activate network 2006:4:4::/128 exit-address-family ! no ip http server no ip http secure-server ip classless ! ! ipv6 router rip R4RIP ! ! ! ! --More--   R4# RACK9AS>2 [Resuming connection 2 to r2 ... ] [OK] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router bgp 100 R2(config-router)#bgp rout 2.2.2.2 R2(config-router)#ad R2(config-router)#address-family i R2(config-router)#address-family ipv6 R2(config-router-af)#net 2006:2:2::/1`28   28 R2(config-router-af)#nei 2005:0:102:0:2D0:BBFF:FEE9:6060 remote 200 R2(config-router-af)#nei *Mar 1 20:57:14.745: %BGP-5-ADJCHANGE: neighbor 2005:0:102:0:2D0:BBFF:FEE9:6060 Up R2(config-router-af)#nei 2000:3:3:: remote 100 R2(config-router-af)#end R2#sh run \ *Mar 1 20:57:35.479: %SYS-5-CONFIG_I: Configured from console by console R2#sh run \   | b bgp router bgp 100 no synchronization bgp router-id 2.2.2.2 bgp log-neighbor-changes neighbor 2000:3:3:: remote-as 100 no neighbor 2000:3:3:: activate neighbor 2005:0:102:0:2D0:BBFF:FEE9:6060 remote-as 200 no neighbor 2005:0:102:0:2D0:BBFF:FEE9:6060 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3:: activate neighbor 2005:0:102:0:2D0:BBFF:FEE9:6060 activate network 2006:2:2::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 2.2.2.2 --More--   R2#sh iopv     pv route IPv6 Routing Table - 18 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::212:7FFF:FE8E:B6C0, Serial1/2 via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 R 2002:B428:742::/64 [120/2] via FE80::2D0:BBFF:FEE9:6060, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:212:7FFF:FE8E:B640/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::2D0:BBFF:FEE9:6060, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:212:7FFF:FE8E:B640/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:212:7FFF:FE8E:B6C0/128 [110/781] via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 --More--   R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] [OK] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router bgp 100 R3(config-router)#bgp rout R3(config-router)#bgp router-id 3.3.3.3 R3(config-router)#ad R3(config-router)#address-family i R3(config-router)#address-family ipv6 R3(config-router-af)#net 2006:3:3::/128 R3(config-router-af)#nei 2005:0:237:0:212:7FFF:FE80:F380 remote 100 R3(config-router-af)#nei 2005:0:237:0:212:7FFF:FE80:F380 remote 100          up R3(config-router-af)#nei 2005:0:237:0:212:7FFF:FE80:F380 update-source lo 0 R3(config-router-af)#nei *Mar 1 20:59:19.842: %BGP-5-ADJCHANGE: neighbor 2005:0:237:0:212:7FFF:FE80:F380 Up R3(config-router-af)#nei      RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#onfi      do sh       sh ip  v int brie FastEthernet0/0 [administratively down/down] unassigned BRI0/0 [administratively down/down] unassigned BRI0/0:1 [administratively down/down] unassigned BRI0/0:2 [administratively down/down] unassigned FastEthernet0/1 [administratively down/down] unassigned Serial1/0 [up/up] unassigned Serial1/0.1 [up/up] FE80::212:7FFF:FE8E:B640 2005:0:237:0:212:7FFF:FE8E:B640 Serial1/0.2 [up/up] FE80::212:7FFF:FE8E:B640 2005:0:702:0:212:7FFF:FE8E:B640 Serial1/1 [up/up] FE80::212:7FFF:FE8E:B640 2005:0:102:0:212:7FFF:FE8E:B640 Serial1/2 [up/up] FE80::212:7FFF:FE8E:B640 --More--   2005:0:1203:0:212:7FFF:FE8E:B640 Serial1/3 [administratively down/down] unassigned Serial1/4 [administratively down/down] unassigned Serial1/5 [administratively down/down] unassigned Serial1/6 [administratively down/down] unassigned Serial1/7 [administratively down/down] unassigned Loopback99 [up/up] FE80::212:7FFF:FE8E:B640 2006:2:2:: R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int lo 0 R2(config-if)#ipv add 2000:2:2::/64 R2(config-if)#router bgp 100 R2(config-router)#add R2(config-router)#address-family i R2(config-router)#address-family ipv6 R2(config-router-af)#address-family ipv6router bgp 100 ipv add 2000:2:2::/64nt lo 0 end nei 2000:3:3:: remote 100          up lo 0 R2(config-router-af)#^Z R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3(config-router-af)#nei 2000:2:2:: remote 100 R3(config-router-af)#nei 2000:2:2:: remote 100          up lo 0 R3(config-router-af)#^Z R3# *Mar 1 21:01:11.802: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes neighbor 2000:2:2:: remote-as 100 neighbor 2000:2:2:: update-source Loopback0 no neighbor 2000:2:2:: activate neighbor 2005:0:237:0:212:7FFF:FE80:F380 remote-as 100 neighbor 2005:0:237:0:212:7FFF:FE80:F380 update-source Loopback0 no neighbor 2005:0:237:0:212:7FFF:FE80:F380 activate no auto-summary ! address-family ipv6 neighbor 2000:2:2:: activate neighbor 2005:0:237:0:212:7FFF:FE80:F380 activate network 2006:3:3::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! --More--   R3# *Mar 1 21:01:33.393: %BGP-5-ADJCHANGE: neighbor 2000:2:2:: Up R3#sh i bgp sum BGP router identifier 3.3.3.3, local AS number 100 BGP table version is 6, main routing table version 6 5 network entries using 665 bytes of memory 5 path entries using 360 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1313 total bytes of memory BGP activity 5/0 prefixes, 5/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:2:2:: 4 100 7 5 6 0 0 00:00:05 3 2005:0:237:0:212:7FFF:FE80:F380 4 100 7 7 6 0 0 00:02:19 1 R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh bgp sum BGP router identifier 2.2.2.2, local AS number 100 BGP table version is 5, main routing table version 5 4 network entries using 532 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1108 total bytes of memory BGP activity 4/0 prefixes, 4/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3:: 4 100 5 7 5 0 0 00:00:27 1 2005:0:102:0:2D0:BBFF:FEE9:6060 4 200 10 10 5 0 0 00:04:42 2 R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 5, main routing table version 5 4 network entries using 532 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1108 total bytes of memory BGP activity 4/0 prefixes, 4/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 0 0 0 0 0 never Idle 2005:0:102:0:212:7FFF:FE8E:B640 4 100 11 11 5 0 0 00:05:13 2 2005:0:104:0:230:85FF:FEF3:7040 4 300 10 12 5 0 0 00:05:20 1 R1# RACK9AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#s hbpg        sh bgp sum BGP router identifier 4.4.4.4, local AS number 300 BGP table version is 5, main routing table version 5 4 network entries using 532 bytes of memory 4 path entries using 288 bytes of memory 3 BGP path attribute entries using 180 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1048 total bytes of memory BGP activity 4/0 prefixes, 4/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2005:0:104:0:2D0:BBFF:FEE9:6061 4 200 12 10 5 0 0 00:05:43 3 R4# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 3, main routing table version 3 2 network entries using 266 bytes of memory 2 path entries using 144 bytes of memory 2 BGP path attribute entries using 120 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 530 total bytes of memory BGP activity 2/0 prefixes, 2/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3:: 4 100 8 8 3 0 0 00:03:45 1 2002:B428:742:: 4 200 0 0 0 0 0 never Idle R7# RACK9AS> [Resuming connection 7 to r7 ... ] R7#ping 2002:B428:742:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:742::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/88/88 ms R7#sh ip  v route 2002:B428:742:: IPv6 Routing Table - 22 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OE2 2002:B428:742::/64 [110/20], tag 2 via FE80::212:7FFF:FE8E:B640, Serial1/0.2 R7# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#con    RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0 R1(config-if)#no ipv rip R1RIP en R1(config-if)#^Z R1# *Mar 1 21:05:39.785: %SYS-5-CONFIG_I: Configured from console by console R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh ipv route 2002:B428:742:: IPv6 Routing Table - 22 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OE2 2002:B428:742::/64 [110/20], tag 2 via FE80::212:7FFF:FE8E:B640, Serial1/0.2 R7#sh ipv route 2002:B428:742:: IPv6 Routing Table - 22 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OE2 2002:B428:742::/64 [110/20], tag 2 via FE80::212:7FFF:FE8E:B640, Serial1/0.2 R7# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh ipv rip data RIP process "R2RIP", local RIB 2002:B428:742::/64, metric 2, installed Serial1/1/FE80::2D0:BBFF:FEE9:6060, expires in 144 secs 2005:0:102::/64, metric 2 Serial1/1/FE80::2D0:BBFF:FEE9:6060, expires in 171 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::2D0:BBFF:FEE9:6060, expires in 171 secs R2#clea ip  v rip data % No such RIPv6 instance R2#clea ipv rip data    R2RIP R2#clea ipv rip R2RIPdata sh ipv rip data  RIP process "R2RIP", local RIB R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh run int tu 0 Building configuration... Current configuration : 142 bytes ! interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:742::/64 tunnel source Ethernet0/0 tunnel mode ipv6ip 6to4 end R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh ipv route 2002:B428:742:: IPv6 Routing Table - 21 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S 2002::/16 [1/0] via ::, Tunnel0 R7#sh ipv route 2002:B428:742:: sh bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 3, main routing table version 3 2 network entries using 266 bytes of memory 2 path entries using 144 bytes of memory 2 BGP path attribute entries using 120 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 530 total bytes of memory BGP activity 2/0 prefixes, 2/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3:: 4 100 11 11 3 0 0 00:06:47 1 2002:B428:742:: 4 200 0 0 0 0 0 never Idle R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh ipv route 2002:B428:701:: IPv6 Routing Table - 23 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S 2002::/16 [1/0] via ::, Tunnel0 R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 5, main routing table version 5 4 network entries using 532 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1108 total bytes of memory BGP activity 4/0 prefixes, 4/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 0 0 0 0 0 never Idle 2005:0:102:0:212:7FFF:FE8E:B640 4 100 15 15 5 0 0 00:09:18 2 2005:0:104:0:230:85FF:FEF3:7040 4 300 14 16 5 0 0 00:09:24 1 R1#deb bgp? bgp R1#deb bgp ? dampening BGP dampening events BGP events ipv6 Address family keepalives BGP keepalives nsap Address family updates BGP updates R1#deb bgp ipv ? dampening BGP dampening updates BGP updates R1#deb bgp ipv BGP debugging is on R1#deb bgp ipv   v ev      ev BGP events debugging is on R1#deb bgp evipv sh bgp sum ipv route 2002:B428:701::bgp sum  BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 5, main routing table version 5 4 network entries using 532 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1108 total bytes of memory BGP activity 4/0 prefixes, 4/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 0 0 0 0 0 never Idle 2005:0:102:0:212:7FFF:FE8E:B640 4 100 16 16 5 0 0 00:10:01 2 2005:0:104:0:230:85FF:FEF3:7040 4 300 15 17 5 0 0 00:10:07 1 R1# *Mar 1 21:08:12.211: BGP: Performing BGP general scanning *Mar 1 21:08:12.211: BGP(0): scanning IPv4 Unicast routing tables *Mar 1 21:08:12.219: BGP(IPv4 Unicast): Performing BGP Nexthop scanning for general scan *Mar 1 21:08:12.219: BGP(0): Future scanner version: 14, current scanner version: 13 *Mar 1 21:08:12.219: BGP(1): scanning IPv6 Unicast routing tables *Mar 1 21:08:12.223: BGP(IPv6 Unicast): Performing BGP Nexthop scanning for general scan *Mar 1 21:08:12.223: BGP(1): Future scanner version: 14, current scanner version: 13 *Mar 1 21:08:12.223: BGP(2): scanning VPNv4 Unicast routing tables R1# *Mar 1 21:08:12.223: BGP(VPNv4 Unicast): Performing BGP Nexthop scanning for general scan *Mar 1 21:08:12.223: BGP(2): Future scanner version: 14, current scanner version: 13 *Mar 1 21:08:12.227: BGP(3): scanning IPv4 Multicast routing tables *Mar 1 21:08:12.235: BGP(IPv4 Multicast): Performing BGP Nexthop scanning for general scan *Mar 1 21:08:12.235: BGP(3): Future scanner version: 14, current scanner version: 13 R1#u all All possible debugging has been turned off R1#deb ipv tcvp    p ? % Unrecognized command R1#deb ipv tcp         tcp ? % Unrecognized command R1#deb tcp     ip tcp ? Winscale Window-Scale driver TCP driver events driver-pak TCP driver verbose header-compression Header compression statistics intercept TCP intercept packet TCP packets rcmd Rcmd transactions sack Selective-ACK transactions Significant TCP events R1#deb ip tcp       p  v ? access-list IPv6 access list debugging cef IPv6 CEF information icmp ICMPv6 debugging interface IPv6 interface debugging nat NAT-PT events nd IPv6 Neighbor Discovery debugging packet IPv6 packet debugging pool IPv6 prefix pool debugging rip RIP Routing Protocol debugging routing IPv6 routing table debugging R1#deb ipv    p tcp % Incomplete command. R1#deb ip tcp ? Winscale Window-Scale driver TCP driver events driver-pak TCP driver verbose header-compression Header compression statistics intercept TCP intercept packet TCP packets rcmd Rcmd transactions sack Selective-ACK transactions Significant TCP events R1#deb ip tcp ta   \           config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int     rotuer      uter bgp 100   200 R1(config-router)#router bgp 200no ipv rip R1RIP enint tu 0 no network 2006:7:7::/128address-family ipv6 router bgp 200 nei 2005:0:102:0:212:7FFF:FE8E:B640 remote 1004:0:230:85FF:FEF3:7040 remote 3002:b428:701:: remote 100           up tu 0 R1(config-router)#^Z R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#csh bgp sumnfig t ^ % Invalid input detected at '^' marker. R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#rotuer bgp r bgp r bgp r bgp ur bgp tr bgp er bgp rr bgp ~r bgp r bgp  bgp  bgp 100 R7(config-router)#nei 2002:b428:742:: up tu 0 R7(config-router)#^Z R7#sh *Mar 1 21:09:35.355: %SYS-5-CONFIG_I: Configured from console by console R7#sh ip    bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 3, main routing table version 3 2 network entries using 266 bytes of memory 2 path entries using 144 bytes of memory 2 BGP path attribute entries using 120 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 530 total bytes of memory BGP activity 2/0 prefixes, 2/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3:: 4 100 15 15 3 0 0 00:10:24 1 2002:B428:742:: 4 200 0 0 0 0 0 never Idle R7#clea ip    bgp * out R7#deb bgp BGP debugging is on R7#deb bgp ? dampening BGP dampening events BGP events ipv6 Address family keepalives BGP keepalives nsap Address family updates BGP updates R7#deb bgp       ip bgp ? A.B.C.D BGP neighbor address X:X:X:X::X IPv6 BGP neighbor address dampening BGP dampening events BGP events in BGP Inbound information keepalives BGP keepalives mpls BGP MPLS label distribution out BGP Outbound information updates BGP updates vpnv4 VPNv4 NLRI information R7#deb ip bgp >     BGP debugging is on R7#deb ip b    bg[   p ? dampening BGP dampening events BGP events ipv6 Address family keepalives BGP keepalives nsap Address family updates BGP updates R7#deb bgp ev BGP events debugging is on R7#sh bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 3, main routing table version 3 2 network entries using 266 bytes of memory 2 path entries using 144 bytes of memory 2 BGP path attribute entries using 120 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 530 total bytes of memory BGP activity 2/0 prefixes, 2/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3:: 4 100 16 17 3 0 0 00:11:24 1 2002:B428:742:: 4 200 0 0 0 0 0 never Idle R7#sh run | *Mar 1 21:10:50.246: BGP: Import timer expired. Walking from 1 to 1 R7#sh run | b bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3:: remote-as 100 no neighbor 2000:3:3:: activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: update-source Tunnel0 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3:: activate neighbor 2002:B428:742:: activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 route 2001:1:1::1/128 2002:B428:742:: --More-- *Mar 1 21:11:05.247: BGP: Import timer expired. Walking from 1 to 1 --More--   R7#u all All possible debugging has been turned off R7#u allsh run | b bgpbgp sum deb bgp evip b bgp clea bgp * outsh bgp sum config t sh bgp sumnfig t ipv route 2002:B428:742:: IPv6 Routing Table - 21 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S 2002::/16 [1/0] via ::, Tunnel0 R7#sh ipv s route s % Ambiguous command: "sh ipv route s" R7#sh ipv route sta IPv6 Routing Table - 21 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S 2001:1:1::1/128 [1/0] via 2002:B428:742:: S 2002::/16 [1/0] via ::, Tunnel0 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#router bvp   gp    bgp 100 R7(config-router)#add i R7(config-router)#add ipv6 R7(config-router-af)#add ipv6router bgp 100nei 2002:b428:742:: up tu 0nnei 2002:b428:742:: up tu 0onei 2002:b428:742:: up tu 0 nei 2002:b428:742:: up tu 0 R7(config-router-af)#no nei 2002:b428:742:: up tu 0       e R7(config-router-af)#no nei 2002:b428:742:: ebgp-multihop 2no nei 2002:b428:742:: ebgp-multihop 2  nei 2002:b428:742:: ebgp-multihop 2  R7(config-router-af)#^Z R7#sh r *Mar 1 21:13:37.861: %SYS-5-CONFIG_I: Configured from console by console R7#sh run |o b bgp ^ % Invalid input detected at '^' marker. R7#sh run |o b bgp b bgp  router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3:: remote-as 100 no neighbor 2000:3:3:: activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3:: activate neighbor 2002:B428:742:: activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 route 2001:1:1::1/128 2002:B428:742:: --More--   R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#confi     sh run | b bgp router bgp 200 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes neighbor 2002:B428:701:: remote-as 100 neighbor 2002:B428:701:: update-source Tunnel0 no neighbor 2002:B428:701:: activate neighbor 2005:0:102:0:212:7FFF:FE8E:B640 remote-as 100 no neighbor 2005:0:102:0:212:7FFF:FE8E:B640 activate neighbor 2005:0:104:0:230:85FF:FEF3:7040 remote-as 300 no neighbor 2005:0:104:0:230:85FF:FEF3:7040 activate no auto-summary ! address-family ipv6 neighbor 2002:B428:701:: activate neighbor 2005:0:102:0:212:7FFF:FE8E:B640 activate neighbor 2005:0:104:0:230:85FF:FEF3:7040 activate network 2006:1:1::/128 exit-address-family ! no ip http server ip classless ! --More--   R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router bgp 200 R1(config-router)#add R1(config-router)#address-family i R1(config-router)#address-family ipv6 R1(config-router-af)#address-family ipv6router bgp 200 nei 2002:b428:701:: up tu 0nnei 2002:b428:701:: up tu 0onei 2002:b428:701:: up tu 0 nei 2002:b428:701:: up tu 0 R1(config-router-af)#no nei 2002:b428:701:: up tu 0       e R1(config-router-af)#no nei 2002:b428:701:: ebgp-multihop 2no nei 2002:b428:701:: ebgp-multihop 2  nei 2002:b428:701:: ebgp-multihop 2  R1(config-router-af)#^Z R1#sh *Mar 1 21:15:53.287: %SYS-5-CONFIG_I: Configured from console by console R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 5, main routing table version 5 4 network entries using 532 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1108 total bytes of memory BGP activity 4/0 prefixes, 4/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 0 0 0 0 0 never Idle 2005:0:102:0:212:7FFF:FE8E:B640 4 100 23 23 5 0 0 00:17:49 2 2005:0:104:0:230:85FF:FEF3:7040 4 300 22 24 5 0 0 00:17:55 1 R1#deb bgp BGP debugging is on R1#deb bgp ? dampening BGP dampening events BGP events ipv6 Address family keepalives BGP keepalives nsap Address family updates BGP updates R1#deb bgp iv R1#deb bgp iv          sh bgp sumconfig t  *Mar 1 21:16:30.640: BGP: 2002:B428:701:: open active, local address 2002:B428:742:: *Mar 1 21:16:30.648: BGP: 2002:B428:701:: went from Active to OpenSent *Mar 1 21:16:30.648: BGP: 2002:B428:701:: sending OPEN, version 4, my as: 200 *Mar 1 21:16:30.652: BGP: 2002:B428:701:: send message type 1, length (incl. header) 45 *Mar 1 21:16:30.656: BGP: 2002:B428:701:: rcv message type 1, length (excl. header) 26 *Mar 1 21:16:30.660: BGP: 2002:B428:701:: rcv OPEN, version 4 *Mar 1 21:16:30.660: BGP: 2002:B428:701:: rcv OPEN w/ OPTION parameter len: 16 *Mar 1 21:16:30.660: BGP: 2002:B428:701:: rcvd OPEN w/ optional parameter type 2 (Capability) len 6 *Mar 1 21:16:30.660: BGP: 2002:B428:701:: OPEN has CAPABILITY code: 1, length 4 *Mar 1 21:16:30.660: BGP: 2002:B428:701:: OPEN has MP_EXT CAP for afi/safi: 2/1 *Mar 1 21:16:30.660: BGP: 2002:B428:701:: rcvd OPEN w/ optional parameter type 2 (Capability) len 2 *Mar 1 21:16:30.660: BGP: 2002:B428:701:: OPEN has CAPABILITY co R1#config tde: 128, length 0 *Mar 1 21:16:30.664: BGP: 2002:B428:701:: OPEN has ROUTE-REFRESH capability(old) for all address-families *Mar 1 21:16:30.664: BGP: 2002:B428:701:: rcvd OPEN w/ optional parameter type 2 (Capability) len 2 *Mar 1 21:16:30.664: BGP: 2002:B428:701:: OPEN has CAPABILITY code: 2, length 0 *Mar 1 21:16:30.664: BGP: 2002:B428:701:: OPEN has ROUTE-REFRESH capability(new) for all address-families *Mar 1 21:16:30.664: BGP: 2002:B428:701:: went from OpenSent to OpenConfirm *Mar 1 21:16:30.664: BGP: 2002:B428:701:: went from OpenConfirm to Established *Mar 1 21:16:30.664: %BGP-5-ADJCHANGE: neighbor 2002:B428:701:: Up R1#config tsh bgp sumdeb bgp        deb bgpsh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 6, main routing table version 6 5 network entries using 665 bytes of memory 6 path entries using 432 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1385 total bytes of memory BGP activity 5/0 prefixes, 6/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 6 8 6 0 0 00:00:30 2 2005:0:102:0:212:7FFF:FE8E:B640 4 100 24 25 6 0 0 00:18:54 2 2005:0:104:0:230:85FF:FEF3:7040 4 300 24 27 6 0 0 00:19:00 1 R1# RACK9AS>4 7 [Resuming connection 7 to r7 ... ] *Mar 1 21:15:39.608: %BGP-5-ADJCHANGE: neighbor 2002:B428 R7#sh ipb     bgp BGP table version is 5, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2002:B428:742:: 0 0 200 i *>i2006:3:3::/128 2000:3:3:: 0 100 0 i *> 2006:4:4::/128 2002:B428:742:: 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7#ping 2006:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:4:4::, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv route 2002:b428:742::/64 tu 0 R7(config)#^Z R7#conf *Mar 1 21:19:21.312: %SYS-5-CONFIG_I: Configured from console by console R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#router bgp 100 R7(config-router)#\ add R7(config-router)#address-family i R7(config-router)#address-family ipv6 R7(config-router-af)#net 2002:b428:701::/64 R7(config-router-af)#^Z R7# *Mar 1 21:19:43.268: %SYS-5-CONFIG_I: Configured from console by con RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv route 2002:b428:701::/64 tu 0 R1(config)#router bgp 200 R1(config-router)#a i % Ambiguous command: "a i" R1(config-router)#a i6 ^ % Invalid input detected at '^' marker. R1(config-router)#a i6   d R1(config-router)#address-family  R1(config-router)#address-family 6 ^ % Invalid input detected at '^' marker. R1(config-router)#address-family 6 i R1(config-router)#address-family ipv6 R1(config-router-af)#net 2002:b428:701::/64 R1(config-router-af)#^Z R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#config tping 2006:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R7#sh ipbv  v ou routte ^ % Invalid input detected at '^' marker. R7#sh ipv oroutteroutte route  IPv6 Routing Table - 24 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OE2 2000:2:2::/64 [110/20] via FE80::212:7FFF:FE8E:B640, Serial1/0.2 OI 2000:3:3::/128 [110/781] via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 S 2001:1:1::1/128 [1/0] via 2002:B428:742:: S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 S 2002:B428:742::/64 [1/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::212:7FFF:FE8E:B640, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 --More--   via FE80::212:7FFF:FE8E:B640, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:212:7FFF:FE80:F380/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:212:7FFF:FE8E:B6C0/128 [110/781] via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:212:7FFF:FE80:F380/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::212:7FFF:FE8E:B640, Serial1/0.2 via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 OI 2005:0:1203:0:212:7FFF:FE8E:B640/128 [110/781] via FE80::212:7FFF:FE8E:B640, Serial1/0.2 OI 2005:0:1203:0:212:7FFF:FE8E:B6C0/128 [110/781] via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 B 2006:1:1::/128 [20/0] via 2002:B428:742:: B 2006:3:3::/128 [200/0] via 2000:3:3:: B 2006:4:4::/128 [20/0] --More--   via 2002:B428:742:: LC 2006:7:7::/128 [0/0] via ::, Loopback99 LC 2007:7:7::7/128 [0/0] via ::, Loopback1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh ipv route IPv6 Routing Table - 19 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OE2 2000:2:2::/64 [110/20] via FE80::212:7FFF:FE8E:B640, Serial1/2 via FE80::212:7FFF:FE8E:B640, Serial1/0 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3::/128 [0/0] via ::, Loopback0 B 2002:B428:701::/64 [200/0] via 2005:0:237:0:212:7FFF:FE80:F380 OE2 2005:0:102::/64 [110/20] via FE80::212:7FFF:FE8E:B640, Serial1/2 via FE80::212:7FFF:FE8E:B640, Serial1/0 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:7FFF:FE8E:B640, Serial1/2 via FE80::212:7FFF:FE8E:B640, Serial1/0 C 2005:0:237::/64 [0/0] via ::, Serial1/0 --More--  L 2005:0:237:0:212:7FFF:FE8E:B6C0/128 [0/0] via ::, Serial1/0 O 2005:0:702::/64 [110/1562] via FE80::212:7FFF:FE8E:B640, Serial1/2 via FE80::212:7FFF:FE8E:B640, Serial1/0 via FE80::212:7FFF:FE80:F380, Serial1/0 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203:0:212:7FFF:FE8E:B640/128 [110/781] via FE80::212:7FFF:FE8E:B640, Serial1/2 L 2005:0:1203:0:212:7FFF:FE8E:B6C0/128 [0/0] via ::, Serial1/2 B 2006:1:1::/128 [200/0] via 2005:0:102:0:2D0:BBFF:FEE9:6060 B 2006:2:2::/128 [200/0] via 2000:2:2:: LC 2006:3:3::/128 [0/0] via ::, Loopback99 B 2006:4:4::/128 [200/0] via 2005:0:102:0:2D0:BBFF:FEE9:6060 B 2006:7:7::/128 [200/0] via 2005:0:237:0:212:7FFF:FE80:F380 L FE80::/10 [0/0] --More--   R3#configt Translating "configt" Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router bgp 100 R3(config-router)#add R3(config-router)#address-family i R3(config-router)#address-family ipv6 R3(config-router-af)#nei     do sh teu n     run | b bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes neighbor 2000:2:2:: remote-as 100 neighbor 2000:2:2:: update-source Loopback0 no neighbor 2000:2:2:: activate neighbor 2005:0:237:0:212:7FFF:FE80:F380 remote-as 100 neighbor 2005:0:237:0:212:7FFF:FE80:F380 update-source Loopback0 no neighbor 2005:0:237:0:212:7FFF:FE80:F380 activate no auto-summary ! address-family ipv6 neighbor 2000:2:2:: activate neighbor 2005:0:237:0:212:7FFF:FE80:F380 activate network 2006:3:3::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! --More--   R3(config-router-af)#neighbor 2005:0:237:0:212:7FFF:FE80:F380  ro R3(config-router-af)#neighbor 2005:0:237:0:212:7FFF:FE80:F380 route-rt  R3(config-router-af)#$05:0:237:0:212:7FFF:FE80:F380 route-reflector-client R3(config-router-af)#^Z R3# *Mar 1 21:22:59.574: %BGP-5-ADJCHANGE: neighbor 2005:0:237:0:212:7FFF:FE80:F380 Down RR client config change *Mar 1 21:22:59.870: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 21:23:28.253: %BGP-5-ADJCHANGE: neighbor 2005:0:237:0:212:7FFF:FE80:F380 Up R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#sh ip  bgp BGP table version is 9, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2002:B428:701::/64 2002:B428:742:: 0 0 200 i *> :: 0 32768 i * i2006:1:1::/128 2005:0:102:0:2D0:BBFF:FEE9:6060 0 100 0 200 i *> 2002:B428:742:: 0 0 200 i *>i2006:2:2::/128 2000:2:2:: 0 100 0 i *>i2006:3:3::/128 2000:3:3:: 0 100 0 i * i2006:4:4::/128 2005:0:102:0:2D0:BBFF:FEE9:6060 0 100 0 200 300 i *> 2002:B428:742:: 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#6  RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh bgp BGP table version is 8, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *>i2002:B428:701::/64 2005:0:237:0:212:7FFF:FE80:F380 0 100 0 i * 2005:0:102:0:2D0:BBFF:FEE9:6060 0 0 200 i *> 2006:1:1::/128 2005:0:102:0:2D0:BBFF:FEE9:6060 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3:: 0 100 0 i *> 2006:4:4::/128 2005:0:102:0:2D0:BBFF:FEE9:6060 0 200 300 i *>i2006:7:7::/128 2005:0:237:0:212:7FFF:FE80:F380 0 100 0 i R2#pin 2006:7:7:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:7:7::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/116/117 ms R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh run | i   b lo  Lo interface Loopback1 no ip address ipv6 address 2001:1:1::1/128 ! interface Loopback99 no ip address ipv6 address 2006:1:1::/128 ! interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:742::/64 tunnel source Ethernet0/0 tunnel mode ipv6ip 6to4 ! interface Ethernet0/0 ip address 180.40.7.66 255.255.255.224 half-duplex ! interface Serial0/0 no ip address shutdown ! --More--   R1#sh ru |    n | b bgp router bgp 200 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes neighbor 2002:B428:701:: remote-as 100 neighbor 2002:B428:701:: ebgp-multihop 2 no neighbor 2002:B428:701:: activate neighbor 2005:0:102:0:212:7FFF:FE8E:B640 remote-as 100 no neighbor 2005:0:102:0:212:7FFF:FE8E:B640 activate neighbor 2005:0:104:0:230:85FF:FEF3:7040 remote-as 300 no neighbor 2005:0:104:0:230:85FF:FEF3:7040 activate no auto-summary ! address-family ipv6 neighbor 2002:B428:701:: activate neighbor 2005:0:102:0:212:7FFF:FE8E:B640 activate neighbor 2005:0:104:0:230:85FF:FEF3:7040 activate network 2002:B428:701::/64 network 2006:1:1::/128 exit-address-family ! no ip http server ip classless --More--   R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b Lo interface Loopback0 no ip address ipv6 address 2000:2:2::/64 ! interface Loopback99 no ip address ipv6 address 2006:2:2::/128 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto --More--   R2#sh run | b router router bgp 100 no synchronization bgp router-id 2.2.2.2 bgp log-neighbor-changes neighbor 2000:3:3:: remote-as 100 neighbor 2000:3:3:: update-source Loopback0 no neighbor 2000:3:3:: activate neighbor 2005:0:102:0:2D0:BBFF:FEE9:6060 remote-as 200 no neighbor 2005:0:102:0:2D0:BBFF:FEE9:6060 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3:: activate neighbor 2005:0:102:0:2D0:BBFF:FEE9:6060 activate network 2006:2:2::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 --More--   router-id 2.2.2.2 log-adjacency-changes area 20 virtual-link 3.3.3.3 distribute-list prefix-list noloop out connected redistribute connected redistribute rip R2RIP tag 2 ! ipv6 router rip R2RIP redistribute connected redistribute ospf 1 metric 2 distribute-list prefix-list noloop out ! ! ! ipv6 prefix-list noloop seq 5 deny 2006:2:2::/128 ipv6 prefix-list noloop seq 10 permit ::/0 le 128 ! ! ! ! ! ! ! --More--   R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | Lo  b Lo interface Loopback0 no ip address ipv6 address 2000:3:3::/64 ipv6 ospf 1 area 51 ! interface Loopback99 no ip address ipv6 address 2006:3:3::/128 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto --More--   R3#sh run | b bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes neighbor 2000:2:2:: remote-as 100 neighbor 2000:2:2:: update-source Loopback0 no neighbor 2000:2:2:: activate neighbor 2005:0:237:0:212:7FFF:FE80:F380 remote-as 100 neighbor 2005:0:237:0:212:7FFF:FE80:F380 update-source Loopback0 no neighbor 2005:0:237:0:212:7FFF:FE80:F380 activate no auto-summary ! address-family ipv6 neighbor 2000:2:2:: activate neighbor 2005:0:237:0:212:7FFF:FE80:F380 activate neighbor 2005:0:237:0:212:7FFF:FE80:F380 route-reflector-client network 2006:3:3::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server --More--   R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#s   sh run | b Lo interface Loopback0 no ip address ipv6 address 2000:4:4::/64 ipv6 rip R4RIP enable ! interface Loopback99 no ip address ipv6 address 2006:4:4::/128 ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2005:0:104::/64 eui-64 ipv6 rip R4RIP enable ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! router bgp 300 no synchronization --More--   bgp router-id 4.4.4.4 bgp log-neighbor-changes neighbor 2005:0:104:0:2D0:BBFF:FEE9:6061 remote-as 200 no neighbor 2005:0:104:0:2D0:BBFF:FEE9:6061 activate no auto-summary ! address-family ipv6 neighbor 2005:0:104:0:2D0:BBFF:FEE9:6061 activate network 2006:4:4::/128 exit-address-family ! no ip http server no ip http secure-server ip classless ! ! ipv6 router rip R4RIP ! ! ! ! ! ! --More--   R4# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b Lo interface Loopback1 no ip address ipv6 address 2007:7:7::7/128 ! interface Loopback99 no ip address ipv6 address 2006:7:7::/128 ! interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:701::/64 ipv6 rip R7RIP enable tunnel source FastEthernet0/1 tunnel mode ipv6ip 6to4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 --More--   R7#sh run | b Lo    bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3:: remote-as 100 no neighbor 2000:3:3:: activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3:: activate neighbor 2002:B428:742:: activate network 2002:B428:701::/64 network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! --More--  ipv6 route 2001:1:1::1/128 2002:B428:742:: ipv6 route 2002:B428:742::/64 Tunnel0 ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! ipv6 router rip R7RIP ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 --More--   R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b ipv6 route ipv6 route 2002:B428:701::/64 Tunnel0 ipv6 route 2002::/16 Tunnel0 ipv6 route 2007:7:7::7/128 2002:B428:701:: ipv6 router rip R1RIP distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! --More--   R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv ? access-list Configure access lists cef Cisco Express Forwarding for IPv6 hop-limit Configure hop count limit host Configure static hostnames icmp Configure ICMP parameters local Specify local options nat NAT-PT Configuration commands neighbor Neighbor prefix-list Build a prefix list route Configure static routes router Enable an IPV6 routing process source-route Process packets with source routing header options unicast-routing Enable unicast routing R1(config)#ipv nat ? max-entries Specify maximum number of NAT-PT entries prefix Configure a global NAT-PT prefix service ALG specific translation NAT-PT translation entry configuration v4v6 IPv4 to IPv6 translation v6v4 IPv6 to IPv4 translation R1(config)#ipv nat pre R1(config)#ipv nat prefix ? X:X:X:X::X/<0-128> IPv6 prefix x:x::y/ R1(config)#ipv nat prefix 2006:66:66666:6666:666666::/64 % Invalid prefix length R1(config)#ipv nat prefix 2006:666:666::/64 5 % Invalid prefix length R1(config)#ipv nat prefix 2006:666:666::/65 6 % Invalid prefix length R1(config)#ipv nat prefix 2006:666:666::/66  96 R1(config)#do sh ipv route IPv6 Routing Table - 26 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:2:2::/64 [120/2] via FE80::212:7FFF:FE8E:B640, Serial0/1 R 2000:3:3::/128 [120/3] via FE80::212:7FFF:FE8E:B640, Serial0/1 R 2000:4:4::/64 [120/2] via FE80::230:85FF:FEF3:7040, Ethernet0/1 LC 2001:1:1::1/128 [0/0] via ::, Loopback1 S 2002::/16 [1/0] via ::, Tunnel0 S 2002:B428:701::/64 [1/0] via ::, Tunnel0 C 2002:B428:742::/64 [0/0] via ::, Tunnel0 L 2002:B428:742::/128 [0/0] via ::, Tunnel0 C 2005:0:102::/64 [0/0] --More--   via ::, Serial0/1 L 2005:0:102:0:2D0:BBFF:FEE9:6060/128 [0/0] via ::, Serial0/1 C 2005:0:104::/64 [0/0] via ::, Ethernet0/1 L 2005:0:104:0:2D0:BBFF:FEE9:6061/128 [0/0] via ::, Ethernet0/1 R 2005:0:237::/64 [120/2] via FE80::212:7FFF:FE8E:B640, Serial0/1 R 2005:0:237:0:212:7FFF:FE8E:B6C0/128 [120/3] via FE80::212:7FFF:FE8E:B640, Serial0/1 R 2005:0:702::/64 [120/2] via FE80::212:7FFF:FE8E:B640, Serial0/1 R 2005:0:1203::/64 [120/2] via FE80::212:7FFF:FE8E:B640, Serial0/1 R 2005:0:1203:0:212:7FFF:FE8E:B6C0/128 [120/3] via FE80::212:7FFF:FE8E:B640, Serial0/1 LC 2006:1:1::/128 [0/0] via ::, Loopback99 B 2006:2:2::/128 [20/0] via FE80::212:7FFF:FE8E:B640, Serial0/1 B 2006:3:3::/128 [20/0] via FE80::212:7FFF:FE8E:B640, Serial0/1 --More--  B 2006:4:4::/128 [20/0] via FE80::230:85FF:FEF3:7040, Ethernet0/1 B 2006:7:7::/128 [20/0] via 2002:B428:701:: C 2006:666:666::/96 [0/0] via ::, Null0 S 2007:7:7::7/128 [1/0] via 2002:B428:701:: L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R1(config)#do sh ipv routeipv nat prefix 2006:666:666::/96              5:0:237:1 6::/96 R1(config)#ipv nat prefix 2005:0:237:6::/96nipv nat prefix 2005:0:237:6::/96oipv nat prefix 2005:0:237:6::/96 ipv nat prefix 2005:0:237:6::/96 R1(config)#no ipv nat prefix 2005:0:237:6::/96ipv nat prefix 2005:0:237:6::/96 nipv nat prefix 2005:0:237:6::/96oipv nat prefix 2005:0:237:6::/96 ipv nat prefix 2005:0:237:6::/96 % Prefix doesnt exist to unconfigure R1(config)#^Z R1# *Mar 1 21:43:34.106: %SYS-5-CONFIG_I: Configured from console by console R1#sh ru  n | i ipv6 nat R1#x7   RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#confiog t ^ % Invalid input detected at '^' marker. R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv nat prew    2005:0:237:6::/96 R7(config)# R7(config)# R7(config)#^Z R7#sh *Mar 1 21:43:29.506: %SYS-5-CONFIG_I: Configured from console by console R7#sh ipv route IPv6 Routing Table - 26 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OE2 2000:2:2::/64 [110/20] via FE80::212:7FFF:FE8E:B640, Serial1/0.2 OI 2000:3:3::/128 [110/781] via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 S 2001:1:1::1/128 [1/0] via 2002:B428:742:: S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 S 2002:B428:742::/64 [1/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::212:7FFF:FE8E:B640, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 --More--   via FE80::212:7FFF:FE8E:B640, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:212:7FFF:FE80:F380/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:212:7FFF:FE8E:B6C0/128 [110/781] via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 C 2005:0:237:6::/96 [0/0] via ::, Null0 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:212:7FFF:FE80:F380/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::212:7FFF:FE8E:B640, Serial1/0.2 via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 OI 2005:0:1203:0:212:7FFF:FE8E:B640/128 [110/781] via FE80::212:7FFF:FE8E:B640, Serial1/0.2 OI 2005:0:1203:0:212:7FFF:FE8E:B6C0/128 [110/781] via FE80::212:7FFF:FE8E:B6C0, Serial1/0.1 B 2006:1:1::/128 [20/0] via 2002:B428:742:: B 2006:2:2::/128 [200/0] --More--   via 2000:2:2:: B 2006:3:3::/128 [200/0] via 2000:3:3:: B 2006:4:4::/128 [20/0] via 2002:B428:742:: LC 2006:7:7::/128 [0/0] via ::, Loopback99 LC 2007:7:7::7/128 [0/0] via ::, Loopback1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#sh bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 9, main routing table version 9 6 network entries using 798 bytes of memory 9 path entries using 648 bytes of memory 6 BGP path attribute entries using 360 bytes of memory 1 BGP rrinfo entries using 24 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1878 total bytes of memory BGP activity 7/1 prefixes, 11/2 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3:: 4 100 57 59 9 0 0 00:20:25 4 2002:B428:742:: 4 200 37 37 9 0 0 00:28:11 3 R7#sh ipv route con IPv6 Routing Table - 26 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 C 2005:0:237:6::/96 [0/0] via ::, Null0 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 LC 2006:7:7::/128 [0/0] via ::, Loopback99 LC 2007:7:7::7/128 [0/0] via ::, Loopback1 R7#configt Translating "configt" Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv nat pre 2005:0:237:6::/96::/96 :/96 ::/96 ::/96 ::/96 :/96 ::/96 :/96 ::/96 6::/96:::/966::/966::/966::/96:::/966::/966::/966::/96 R7(config)#ipcv  v nat 4 R7(config)#ipv nat 4 v4 R7(config)#ipv nat v4v6 ? pool Configure a IPv6 address pool source Source Address Translation R7(config)#ipv nat v4v6 sou R7(config)#ipv nat v4v6 source ? A.B.C.D IPv4 address to translate list Specify access list R7(config)#ipv nat v4v6 source                     access-list 1 per 180.40.7.2 R7(config)#access-list 1 per 180.40.7.2  .33 R7(config)#ipv nat v4 R7(config)#ipv nat v4v6 ? pool Configure a IPv6 address pool source Source Address Translation R7(config)#ipv nat v4v6 sou R7(config)#ipv nat v4v6 source li R7(config)#ipv nat v4v6 source list ? <1-199> Access list number WORD Access list name R7(config)#ipv nat v4v6 source list 1 ? pool Specify pool name R7(config)#ipv nat v4v6 source list 1                            ipv nat ? max-entries Specify maximum number of NAT-PT entries prefix Configure a global NAT-PT prefix service ALG specific translation NAT-PT translation entry configuration v4v6 IPv4 to IPv6 translation v6v4 IPv6 to IPv4 translation R7(config)#ipv nat v4   R7(config)#ipv nat v4v6 ? pool Configure a IPv6 address pool source Source Address Translation R7(config)#ipv nat v4v6 pol R7(config)#ipv nat v4v6 pol  R7(config)#ipv nat v4v6 pool ? WORD Pool name R7(config)#ipv nat v4v6 pool ProbF ? X:X:X:X::X Start IPv6 address R7(config)#ipv nat v4v6 pool ProbF 2006:666:6656  6::6 ? X:X:X:X::X End IPv6 address R7(config)#ipv nat v4v6 pool ProbF 2006:666:666::6 2006:6366   66:666::f % Incomplete command. R7(config)#ipv nat v4v6 pool ProbF 2006:666:666::6 2006:666:666::f ? prefix-length Specify the prefix length R7(config)#ipv nat v4v6 pool ProbF 2006:666:666::6 2006:666:666::f pre R7(config)#$6 pool ProbF 2006:666:666::6 2006:666:666::f prefix-length ? <1-128> Prefix length R7(config)#$6 pool ProbF 2006:666:666::6 2006:666:666::f prefix-length 96 R7(config)#ipv nat v4 R7(config)#ipv nat v4v6 so R7(config)#ipv nat v4v6 source l R7(config)#ipv nat v4v6 source list 1 R7(config)#ipv nat v4v6 source list 1 ? pool Specify pool name R7(config)#ipv nat v4v6 source list 1 po R7(config)#ipv nat v4v6 source list 1 pool ProbF ? R7(config)#ipv nat v4v6 source list 1 pool ProbF R7(config)#ipv nat v6 R7(config)#ipv nat v6v4 ? pool Configure a IPv4 address pool source Source Address Translation R7(config)#ipv nat v6v4 sou ? X:X:X:X::X IPv6 address to translate list Specify access list route-map Configure a route-map R7(config)#ipv nat v6v4 sou 2005:0:237:0:212:7FFF:FE8E:B6C0 ? A.B.C.D IPv4 Address R7(config)#ipv nat v6v4 sou 2005:0:237:0:212:7FFF:FE8E:B6C0 33.33.33.33 ? R7(config)#ipv nat v6v4 sou 2005:0:237:0:212:7FFF:FE8E:B6C0 33.33.33.33 R7(config)#routr er bgp 100 R7(config-router)#ad R7(config-router)#address-family i R7(config-router)#address-family ipv6 R7(config-router)#address-family ipv6 R7(config-router-af)#net 2006:666:666::/96 R7(config-router-af)#exit R7(config-router)#exit R7(config)#ip route R7(config)#ip route 33.33.33.0 255, .255.255.0 nul 0 R7(config)#router bgp     rip R7(config-router)#redis R7(config-router)#redistribute sta R7(config-router)#redistribute static ? metric Metric for redistributed routes route-map Route map reference R7(config-router)#redistribute static R7(config-router)#^Z R7# RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 33.0.0.0/24 is subnetted, 1 subnets R 33.33.33.0 [120/1] via 180.40.7.1, 00:00:03, FastEthernet0/7 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/7 C 180.40.7.32 is directly connected, FastEthernet0/24 R 180.40.7.64 [120/1] via 180.40.7.34, 00:00:07, FastEthernet0/24 S6#pi 33.33.33.33 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 33.33.33.33, timeout is 2 seconds: U.U.U Success rate is 0 percent (0/5) S6# RACK9AS>6 \3 % Unknown command or computer name, or unable to find computer address RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh ipv route IPv6 Routing Table - 20 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OE2 2000:2:2::/64 [110/20] via FE80::212:7FFF:FE8E:B640, Serial1/2 via FE80::212:7FFF:FE8E:B640, Serial1/0 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3::/128 [0/0] via ::, Loopback0 B 2002:B428:701::/64 [200/0] via 2005:0:237:0:212:7FFF:FE80:F380 OE2 2005:0:102::/64 [110/20] via FE80::212:7FFF:FE8E:B640, Serial1/2 via FE80::212:7FFF:FE8E:B640, Serial1/0 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:7FFF:FE8E:B640, Serial1/2 via FE80::212:7FFF:FE8E:B640, Serial1/0 C 2005:0:237::/64 [0/0] via ::, Serial1/0 --More--  L 2005:0:237:0:212:7FFF:FE8E:B6C0/128 [0/0] via ::, Serial1/0 O 2005:0:702::/64 [110/1562] via FE80::212:7FFF:FE8E:B640, Serial1/2 via FE80::212:7FFF:FE8E:B640, Serial1/0 via FE80::212:7FFF:FE80:F380, Serial1/0 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203:0:212:7FFF:FE8E:B640/128 [110/781] via FE80::212:7FFF:FE8E:B640, Serial1/2 L 2005:0:1203:0:212:7FFF:FE8E:B6C0/128 [0/0] via ::, Serial1/2 B 2006:1:1::/128 [200/0] via 2005:0:102:0:2D0:BBFF:FEE9:6060 B 2006:2:2::/128 [200/0] via 2000:2:2:: LC 2006:3:3::/128 [0/0] via ::, Loopback99 B 2006:4:4::/128 [200/0] via 2005:0:102:0:2D0:BBFF:FEE9:6060 B 2006:7:7::/128 [200/0] via 2005:0:237:0:212:7FFF:FE80:F380 B 2006:666:666::/96 [200/0] --More--   via 2005:0:237:0:212:7FFF:FE80:F380 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh ipv nat ? statistics Translation statistics translations Translation entries R7#sh ipv nat tra R7#sh ipv nat translations Prot IPv4 source IPv6 source IPv4 destination IPv6 destination --- 33.33.33.33 2005:0:237:0:212:7FFF:FE8E:B6C0 --- --- R7#sh    confi g ^ % Invalid input detected at '^' marker. R7#confi gt ^ % Invalid input detected at '^' marker. R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#ipv nat R7(config-if)#int s 1/0.1 R7(config-subif)#int s 1/0.1pv nat  ? prefix Configure NAT-PT prefix on interface R7(config-subif)#ipv nat R7(config-subif)#^Z R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh ipv routerun | b bgpLo config t sh run | b Lobgpipv route   RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#pi 33.33.33.33 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 33.33.33.33, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/78/104 ms S6#pi 33.33.33.33pi 33.33.33.33 33.33.33.33 33.33.33.33  Trying 33.33.33.33 ... Open R3# R3# R3#q [Connection to 33.33.33.33 closed by foreign host] S6# RACK9AS>7 [Resuming connection 7 to r7 ... ] * R7#sh run | b 0/1 tunnel source FastEthernet0/1 tunnel mode ipv6ip 6to4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.1 255.255.255.224 duplex auto speed auto ipv6 nat ! interface Serial1/0 no ip address encapsulation frame-relay ! --More--  interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::/64 eui-64 ipv6 nat ipv6 ospf 1 area 0 frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::/64 eui-64 ipv6 ospf 1 area 0 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! --More--  interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router rip version 2 redistribute static network 180.40.0.0 no auto-summary ! router bgp 100 --More--   no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3:: remote-as 100 no neighbor 2000:3:3:: activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3:: activate neighbor 2002:B428:742:: activate network 2002:B428:701::/64 network 2006:7:7::/128 network 2006:666:666::/96 exit-address-family ! ip classless ip route 33.33.33.0 255.255.255.0 Null0 ! no ip http server no ip http secure-server --More--  ! access-list 1 permit 180.40.7.2 access-list 1 permit 180.40.7.33 ipv6 route 2001:1:1::1/128 2002:B428:742:: ipv6 route 2002:B428:742::/64 Tunnel0 ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! ipv6 router rip R7RIP ! ipv6 nat v4v6 source list 1 pool ProbF ipv6 nat v4v6 pool ProbF 2006:666:666::6 2006:666:666::F prefix-length 96 ipv6 nat v6v4 source 2005:0:237:0:212:7FFF:FE8E:B6C0 33.33.33.33 ipv6 nat prefix 2006:666:666::/96 ! ! ! ! ! ! ! --More--   R7# R7#