=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.07.10 16:22:52 =~=~=~=~=~=~=~=~=~=~=~= R7# R7# R7# R7# R7# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int fa 0/2 ^ % Invalid input detected at '^' marker. R2#sh run int fa 0/2 1 Building configuration... Current configuration : 98 bytes ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 duplex auto speed auto end R2#sh ip int fa 0/1 FastEthernet0/1 is up, line protocol is up Internet address is 180.40.7.98/27 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Multicast reserved groups joined: 224.0.0.5 224.0.0.6 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF Fast switching turbo vector IP multicast fast switching is enabled --More--   IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is disabled WCCP Redirect outbound is disabled WCCP Redirect inbound is disabled WCCP Redirect exclude is disabled BGP Policy Mapping is disabled R2#q  R2# R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip mu R1(config)#ip multicast- R1(config)#ip multicast-routing R1(config)#int e 0/0 R1(config-if)#ip sp R1(config-if)#ip split-horizon               pim R1(config-if)#ip pim ssp  p R1(config-if)#ip pim sparse-d R1(config-if)#ip pim sparse-dense-mode R1(config-if)# *Mar 1 05:19:44.147: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.57.100.1 on interface Ethernet0/0 (vrf default) R1(config-if)#int p pim sparse-dense-mode nt e 0/0  1 R1(config-if)#int e 0/1p pim sparse-dense-mode R1(config-if)#int s 0/0.1 R1(config-subif)# *Mar 1 05:19:56.555: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.100.1.1 on interface Ethernet0/1 (vrf default) R1(config-subif)#int s 0/0.1p pim sparse-dense-mode R1(config-subif)#ip pim sparse-dense-mode nt s 0/0.1  2 R1(config-subif)#int s 0/0.2p pim sparse-dense-mode R1(config-subif)#do sh ru  ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 17.57.100.1 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 180.40.7.34 YES manual administratively down down Serial0/0.2 180.40.7.66 YES manual up up Ethernet0/1 17.100.1.1 YES manual up up Serial0/1 unassigned YES manual administratively down down R1(config-subif)#do sh ip int brieip pim sparse-dense-mode nt s 0/0.2  1 R1(config-subif)#no shut R1(config-subif)#^Z R1# *Mar 1 05:20:14.870: %SYS-5-CONFIG_I: Configured from console by console R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#confi g ^ % Invalid input detected at '^' marker. R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip mul R2(config)#ip multicast- R2(config)#ip multicast-routing R2(config)#int fa 0/1 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#int *Mar 1 05:20:18.936: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.98 on interface FastEthernet0/1 (vrf default) R2(config-if)#int s 1/2 R2(config-if)#int s 1/2p pim sparse-dense-mode R2(config-if)#int s 1// 0.1 R2(config-subif)#int s 1/0.1p pim sparse-dense-mode R2(config-subif)#ip pim sparse-dense-mode nt s 1/0.1  2 R2(config-subif)#int s 1/0.2p pim sparse-dense-mode R2(config-subif)# *Mar 1 05:20:28.744: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.35 on interface Serial1/0.1 (vrf default) *Mar 1 05:20:29.741: %PIM-5-NBRCHG: neighbor 180.40.7.66 UP on interface Serial1/0.2 (vrf default) *Mar 1 05:20:29.746: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.66 on interface Serial1/0.2 (vrf default) R2(config-subif)#^Z R2# *Mar 1 05:20:31.709: %SYS-5 RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip mu R3(config)#ip multicast- R3(config)#ip multicast-routing R3(config)#int s 1/2 R3(config-if)#int s 1/2 ip po i,   m spa R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)#int *Mar 1 05:20:51.633: %PIM-5-NBRCHG: neighbor 180.40.7.2 UP on interface Serial1/2 (vrf default) R3(config-if)#int s 1/-0 09   0 R3(config-if)#int s 1/0p pim sparse-dense-mode R3(config-if)#\  *Mar 1 05:20:57.904: %PIM-5-NBRCHG: neighbor 180.40.7.34 UP on interface Serial1/0 (vrf default) *Mar 1 05:20:57.904: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.34 on interface Serial1/0 (vrf default) *Mar 1 05:20:57.940: %PIM-5-NBRCHG: neighbor 180.40.7.35 UP on interface Serial1/0 (vrf default) *Mar 1 05:20:57.940: %PIM-5-DRCHG: DR change from neighbor 180.40.7.34 to 180.40.7.35 on interface Serial1/0 (vrf default) R3(config-if)#int fa 0/1 1 R3(config-if)#int fa 0/1p pim sparse-dense-mode R3(config-if)#^Z R3# *Mar 1 05:21:05.288: %SYS-5-CONFIG_I: Configured from console by console R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# *Mar 1 05:21:06.638: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.129 on interface FastEthernet0/1 (vrf default) R3(config)#^Z R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#ip mu R4(config)#ip multicast- R4(config)#ip multicast-routing R4(config)#\int fa 0/0 ^ % Invalid input detected at '^' marker. R4(config)#\int fa 0/0\int fa 0/0  R4(config-if)#ip po im den R4(config-if)#ip pim dense-mode R4(config-if)# *Mar 1 05:23:48.070: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.130 on interface FastEthernet0/0 (vrf default) R4(config-if)#^Z R4# *Mar 1 05:24:01.542: %SYS-5-CONFIG_I: Configured from console by console R4# RACK9AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip mu S5(config)#ip multicast- S5(config)#ip multicast-routing S5(config)#int fa 0/'1  1 S5(config-if)#ip pim,    sp S5(config-if)#ip pim sparse-d S5(config-if)#ip pim sparse-dense-mode S5(config-if)#int   ^Z S5# 05:25:08: %SYS-5-CONFIG_I: Configured from console by console S5# RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#configt Translating "configt" % Unknown command or computer name, or unable to find computer address S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip mu S6(config)#ip multicast- S6(config)#ip multicast-routing S6(config)#int fa 0/2 S6(config-if)#ip pim sp S6(config-if)#ip pim sparse-d S6(config-if)#ip pim sparse-dense-mode S6(config-if)#^Z S6# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip mul R7(config)#ip multicast- R7(config)#ip multicast-routing R7(config)#int fa 0/1 R7(config-if)#ip pim sp R7(config-if)#ip pim sparse-d R7(config-if)#ip pim sparse-dense-mode R7(config-if)#^Z R7#sh *Mar 1 05:22:36.433: %SYS-5-CONFIG_I: Configured from console by console R7#sh ip int fbrie *Mar 1 05:22:37.992: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.100.1.2 on interface FastEthernet0/1 (vrf default) R7#sh ip int fbrie ^ % Invalid input detected at '^' marker. R7#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES manual administratively down down BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 17.100.1.2 YES manual up up Serial1/0 unassigned YES manual administratively down down Serial1/1 unassigned YES manual administratively down down Serial1/2 unassigned YES manual administratively down down Serial1/3 unassigned YES manual administratively down down Serial1/4 unassigned YES manual administratively down down Serial1/5 unassigned YES manual administratively down down --More--   R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh ip int brip ^ % Invalid input detected at '^' marker. R1#sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 17.57.100.1 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 180.40.7.34 YES manual up up Serial0/0.2 180.40.7.66 YES manual up up Ethernet0/1 17.100.1.1 YES manual up up Serial0/1 unassigned YES manual administratively down down R1# RACK9AS>z 4 [Resuming connection 4 to r4 ... ] *Ma R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#ip ig R4(config-if)#ip igmp j R4(config-if)#ip igmp join-group 244.4.4      2. 4.4.4.4 R4(config-if)#^Z R4# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 132 ms Reply to request 0 from 180.40.7.130, 180 ms Reply to request 0 from 180.40.7.130, 164 ms R7# RACK9AS>6 [Resuming connection 6 to r6 ... ] 05: S6#ping 24 24.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 68 ms Reply to request 0 from 180.40.7.130, 128 ms Reply to request 0 from 180.40.7.130, 84 ms S6# RACK9AS>2 [Resuming connection 2 to r2 ... ] -CONFIG_I: Configured from console by console R2# R2#sh run int df  s0 140.1 ^ % Invalid input detected at '^' marker. R2#sh run int s140.100.1 /0.1 Building configuration... Current configuration : 267 bytes ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 end R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/02 R2(config-if)#int s 1/02.2 R2(config-subif)#shut R2(config-subif)# *Mar 1 05:28:03.746: %PIM-5-NBRCHG: neighbor 180.40.7.66 DOWN on interface Serial1/0.2 (vrf default) DR *Mar 1 05:28:03.746: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.66 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-subif)#shutint s 1/0.2 1 R2(config-subif)#no frame-relay map ip 180.40.7.34 203 broadcast R2(config-subif)#no frame-relay map ip 180.40.7.34 203 broadcast broadcast 1 broadcastno frame-relay map ip 180.40.7.34 201 broadcast  frame-relay map ip 180.40.7.34 201 broadcast  %PVC already assigned to interface Serial1/0.2 R2(config-subif)#do sh run int s 1/0.1 Building configuration... Current configuration : 221 bytes ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay interface-dlci 203 end R2(config-subif)#no do sh run int s 1/0.1 2 Building configuration... Current configuration : 185 bytes ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint shutdown frame-relay interface-dlci 201 end R2(config-subif)#int s 1/0.2 R2(config-subif)#no frame-relay interface-dlci 201 R2(config-subif)#no frame-relay interface-dlci 201int s 1/0.2  1 R2(config-subif)#int s 1/0.1no frame-relay interface-dlci 201int s 1/0.2 do sh run int s 1/0.21 frame-relay map ip 180.40.7.34 201 broadcast R2(config-subif)# *Mar 1 05:29:03.035: %PIM-5-NBRCHG: neighbor 180.40.7.66 UP on interface Serial1/0.1 (vrf default) *Mar 1 05:29:03.039: %PIM-5-DRCHG: DR change from neighbor 180.40.7.35 to 180.40.7.66 on interface Serial1/0.1 (vrf default) R2(config-subif)# RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 80 ms Reply to request 0 from 180.40.7.130, 96 ms S6# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2(config-subif)#do pi 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 36 ms Reply to request 0 from 180.40.7.130, 80 ms R2(config-subif)# RACK9AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa0/1 S5(config-if)#ip ig S5(config-if)#ip igmp j S5(config-if)#ip igmp join-group 225 4.45  5.5.5 S5(config-if)#^Z S5# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2(config-subif)#do p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R2(config-subif)#do p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R2(config-subif)#do p 224.5.5.5i 224.4.4.4 frame-relay map ip 180.40.7.34 201 broadcastn frame-relay map ip 180.40.7.34 201 broadcasto frame-relay map ip 180.40.7.34 201 broadcast frame-relay map ip 180.40.7.34 201 broadcast R2(config-subif)#no frame-relay map ip 180.40.7.34 201 broadcastdo p 224.5.5.5 i 224.4.4.4 224.5.5.5 no frame-relay map ip 180.40.7.34 201 broadcast no frame-relay map ip 180.40.7.34 201 broadcast broadcast 3 broadcastno frame-relay map ip 180.40.7.34 203 broadcast  frame-relay map ip 180.40.7.34 203 broadcast  R2(config-subif)# frame-relay map ip 180.40.7.34 203 broadcastno frame-relay map ip 180.40.7.34 201 broadcastdo p 224.5.5.5 i 224.4.4.4 frame-relay map ip 180.40.7.34 201 broadcastint s 1/0.1 no frame-relay interface-dlci 201int s 1/0.2  R2(config-subif)#int s 1/0.2 frame-relay map ip 180.40.7.34 203 broadcastno frame-relay map ip 180.40.7.34 201 broadcastdo p 224.5.5.5 i 224.4.4.4 frame-relay map ip 180.40.7.34 201 broadcastint s 1/0.1 no frame-relay interface-dlci 201no frame-relay interface-dlci 201  frame-relay interface-dlci 201  R2(config-fr-dlci)#no shut R2(config-subif)#^Z R2# *Mar 1 05:33:16.855: %SYS-5-CONFIG_I: Configured from console by console R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh run | b ip mu;l   ip multicast-routing ip cef ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode half-duplex ! interface Serial0/0 --More--   R1# R1#sh run int e 0/0 Building configuration... Current configuration : 106 bytes ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode half-duplex end R1# R1# RACK9AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#sh run | b ip mul ip multicast-routing ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim dense-mode --More--   ip igmp join-group 224.4.4.4 --More--   duplex auto --More--   R4# R4# R4# R4# R4# R4# R4# R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#itn    nt fa 0/09  R4(config-if)#ip pim ? bidir-neighbor-filter PIM bidir capable peering filter bsr-border Border of PIM domain dense-mode Enable PIM dense-mode operation dr-priority PIM router DR priority nbma-mode Use Non-Broadcast Multi-Access (NBMA) mode on interface neighbor-filter PIM peering filter query-interval PIM router query interval sparse-dense-mode Enable PIM sparse-dense-mode operation sparse-mode Enable PIM sparse-mode operation state-refresh PIM DM State-Refresh configuration version PIM version R4(config-if)#ip pim st R4(config-if)#ip pim state-refresh ? origination-interval PIM State-Refresh origination interval R4(config-if)#ip pim state-refresh o R4(config-if)#ip pim state-refresh origination-interval ? <1-100> Interval in seconds R4(config-if)#ip pim state-refresh origination-interval 8 R4(config-if)#^Z R4#sh *Mar 1 05:38:23.550: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip pim int fa 0/0 de R4#sh ip pim int fa 0/0 detail FastEthernet0/0 is up, line protocol is up Internet address is 180.40.7.130/27 Multicast switching: fast Multicast packets in/out: 12/0 Multicast boundary: not set Multicast TTL threshold: 0 PIM: enabled PIM version: 2, mode: dense PIM DR: 180.40.7.130 (this system) PIM neighbor count: 1 PIM Hello/Query interval: 30 seconds PIM State-Refresh processing: enabled PIM State-Refresh origination: enabled, interval: 8 seconds PIM NBMA mode: disabled PIM ATM multipoint signalling: disabled PIM domain border: disabled Multicast Tagswitching: disabled R4#deb ip pim ? Hostname or A.B.C.D IP group address atm PIM ATM signalling activity auto-rp Auto-RP bsr PIM Candidate-RP/BSR activity df PIM RP designated forwarder election activity hello PIM Hello packets tag PIM multicast tagswitching activity vrf Select VPN Routing/Forwarding instance R4#deb ip pim PIM debugging is on R4# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#pi 224.7.7.7 ? data specify data pattern df-bit enable do not fragment bit in IP header repeat specify repeat count size specify datagram size source specify source address or name timeout specify timeout interval validate validate reply data R3#pi 224.7.7.7 re R3#pi 224.7.7.7 repeat 100 Type escape sequence to abort. Sending 100, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: RACK9AS>4 [Resuming connection 4 to r4 ... ] R4# *Mar 1 05:39:24.326: PIM(0): Insert (180.40.7.33,224.7.7.7) prune in nbr 180.40.7.129's queue *Mar 1 05:39:24.326: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 05:39:24.326: PIM(0): Adding v2 (180.40.7.33/32, 224.7.7.7) Prune *Mar 1 05:39:24.326: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) R4# *Mar 1 05:39:32.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4# *Mar 1 05:39:40.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4# *Mar 1 05:39:48.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4# *Mar 1 05:39:56.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4# *Mar 1 05:40:04.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4# *Mar 1 05:40:12.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4# *Mar 1 05:40:20.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4# *Mar 1 05:40:28.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4#con *Mar 1 05:40:36.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4#config         *Mar 1 05:40:44.026: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4#deb ip pack de IP packet debugging is on (detailed) R4#deb ip pack de *Mar 1 05:40:50.934: IP: s=180.40.7.130 (local), d=224.0.0.5 (FastEthernet0/0), len 80, sending broad/multicast, proto=89 R4#deb ip pack de *Mar 1 05:40:52.046: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4#deb ip pack de *Mar 1 05:40:57.530: IP: s=180.40.7.129 (FastEthernet0/0), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 05:40:57.770: IP: s=180.40.7.130 (local), d=224.0.0.13 (FastEthernet0/0), len 54, sending broad/multicast, proto=103 R4#deb ip pack de *Mar 1 05:40:59.810: IP: s=180.40.7.129 (FastEthernet0/0), d=224.0.0.13, len 54, rcvd 0, proto=103 *Mar 1 05:40:59.950: IP: s=192.10.32.254 (ATM1/0), d=192.10.32.9, len 44, rcvd 0 *Mar 1 05:40:59.950: TCP src=54140, dst=179, seq=3458949805, ack=0, win=16384 SYN *Mar 1 05:40:59.950: IP: tableid=0, s=192.10.32.9 (local), d=192.10.32.254 (ATM1/0), routed via FIB *Mar 1 05:40:59.950: IP: s=192.10.32.9 (local), d=192.10.32.254 (ATM1/0), len 40, sending *Mar 1 05:40:59.950: TCP src=179, dst=54140, seq=0, ack=3458949806, win=0 ACK RST *Mar 1 05:41:00.046: PIM(0): Originating refresh message for (180.40.7.129,224.7.7.7) R4#deb ip pack de *Mar 1 05:41:00.934: IP: s=180.40.7.130 (local), d=224.0.0.5 (FastEthernet0/0), len 80, sending broad/multicast, proto=89 R4#deb ip pack de              u a *Mar 1 05:41:05.650: IP: s=180.40.7.129 (FastEthernet0/0), d=224.0.0.5, len 84, rcvd 0, proto=89 R4#u all All possible debugging has been turned off R4#inty      config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#int fa 0/0p pim state-refresh origination-interval 88 R4(config-if)#^Z R4# *Mar 1 05:41:18.698: %SYS-5-CONFIG_I: Configured from console by console R4#sh run int fa 0./  /0 Building configuration... Current configuration : 209 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 88 ip pim dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4# R4# R4# RACK9AS>3 [Resuming connection 3 to r3 ... ] .... R3#x wr Building configuration... [OK] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#access-list 1 den 224.206 .68.1 R3(config)#access-list 1 per any R3(config)#ip p pim rp R3(config)#ip pim rp-a R3(config)#ip pim rp-ad R3(config)#ip pim rp-address 180.40.7.129 R3(config)#ip pim rp-address 180.40.7.129 ? <1-99> Access-list reference for group <1300-1999> Access-list reference for group (expanded range) WORD IP Named Standard Access list override Overrides dynamically learnt RP mappings R3(config)#ip pim rp-address 180.40.7.129 1 R3(config)#do    ^Z R3#sh run *Mar 1 05:47:44.069: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b ip pim rp ip pim rp-address 180.40.7.129 1 ! access-list 1 deny 224.20.68.1 access-list 1 permit any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end --More--   R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)# R1(config)# R1(config)#ip pim rp-address 180.40.7.129 1 R1(config)#! R1(config)#access-list 1 deny 224.20.68.1 R1(config)#access-list 1 permit any R1(config)#! R1(config)# R1(config)#end R1# *Mar 1 05:49:01.083: %SYS-5-CONFIG_I: Co RACK9AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)# R2(config)# R2(config)#ip pim rp-address 180.40.7.129 1 R2(config)#! R2(config)#access-list 1 deny 224.20.68.1 R2(config)#access-list 1 permit any R2(config)#! R2(config)# R2(config)#end R2# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4# RACK9AS>4 5 [Resuming connection 5 to r5 ... ] 05:3config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)# S5(config)# S5(config)#ip pim rp-address 180.40.7.129 1 S5(config)#! S5(config)#access-list 1 deny 224.20.68.1 S5(config)#access-list 1 permit any S5(config)#! S5(config)# S5(config)#end S5# 05:51:37: %SYS-5-CONFIG_I: Con RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)# S6(config)# S6(config)#ip pim rp-address 180.40.7.129 1 S6(config)#! S6(config)#access-list 1 deny 224.20.68.1 S6(config)#access-list 1 permit any S6(config)#! S6(config)# S6(config)#end S6# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)# R7(config)# R7(config)#ip pim rp-address 180.40.7.129 1 R7(config)#! R7(config)#access-list 1 deny 224.20.68.1 R7(config)#access-list 1 permit any R7(config)#! R7(config)# R7(config)#end R7(tcl)# R7(tcl)# *Mar 1 05:48:29.171: %SYS-5-CONFIG_I: Configured from console by console R7(tcl)#exit R7 con0 is now available Press RETURN to get started. R7> R7>en R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 120 ms R7# R7#sh ip        RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mrtou   out IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:26:09/stopped, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:26:09/00:00:16 (17.100.1.2, 224.4.4.4), 00:00:44/00:02:15, flags: Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:44/00:02:15 (*, 224.5.5.5), 00:01:52/00:02:36, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:01:52/00:02:36 (*, 224.0.1.40), 00:29:32/00:02:42, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: --More--   Serial1/0, Forward/Sparse-Dense, 00:01:58/00:02:31 FastEthernet0/1, Forward/Sparse-Dense, 00:29:06/00:00:08 Serial1/2, Forward/Sparse-Dense, 00:29:40/00:00:11 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#^Z R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/09 ^ % Invalid input detected at '^' marker. R4(config)#int fa 0/09  R4(config-if)#ip iog  gpo  R4(config-if)#ip igp m R4(config-if)#ip igmp j R4(config-if)#ip igmp join-group 224.20.68.1 R4(config-if)#^Z R4# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 121 ms Reply to request 0 from 180.40.7.130, 153 ms Reply to request 0 from 180.40.7.130, 133 ms R7#sh ip mrou IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:01:37/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (17.100.1.2, 224.4.4.4), 00:01:37/00:01:31, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0, Registering Outgoing interface list: Null (*, 224.0.1.40), 00:02:39/00:02:24, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#config tsh ip mrout IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:00:22/stopped, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:22/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:22/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:22/00:00:00 (17.100.1.2, 224.20.68.1), 00:00:15/00:02:51, flags: T Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Serial1/2, Prune/Sparse-Dense, 00:00:17/00:02:46 FastEthernet0/1, Forward/Sparse-Dense, 00:00:17/00:00:00 (*, 224.4.4.4), 00:27:13/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (17.100.1.2, 224.4.4.4), 00:01:48/00:01:11, flags: --More--   Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:58/00:01:01 (*, 224.5.5.5), 00:03:05/00:03:20, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:03:05/00:03:20 (*, 224.0.1.40), 00:30:45/00:03:17, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:03:10/00:03:17 Serial1/2, Forward/Sparse-Dense, 00:30:45/00:02:06 R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] nfigured from console by console R1# R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#config t ^ % Invalid input detected at '^' marker. R1(config)# R1(config)#no ip pim rp-address 180.40.7.129 1 R1(config)#! R1(config)#no access-list 1 deny 224.20.68.1 R1(config)#! R1(config)# R1(config)#end R1#^Z R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] *Ma R2# R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#no ip pim rp-address 180.40.7.129 1 R2(config)#! R2(config)#no access-list 1 deny 224.20.68.1 R2(config)#! R2(config)# R2(config)#end R2# *Mar 1 05:52:52.294: %SYS-5-CONFIG_I RACK9AS>3 4 [Resuming connection 4 to r4 ... ] *Ma RACK9AS>5 [Resuming connection 5 to r5 ... ] figured from console by console S5# S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#no ip pim rp-address 180.40.7.129 1 S5(config)#! S5(config)#no access-list 1 deny 224.20.68.1 S5(config)#! S5(config)# S5(config)#end S5# RACK9AS>6 [Resuming connection 6 to r6 ... ] 05: S6# S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#no ip pim rp-address 180.40.7.129 1 S6(config)#! S6(config)#no access-list 1 deny 224.20.68.1 S6(config)#! S6(config)# S6(config)#end S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#no ip pim rp-address 180.40.7.129 1 S6(config)#! S6(config)#no access-list 1 deny 224.20.68.1 S6(config)#! S6(config)# S6(config)#end S6# 05:56:08: %SYS-5-CONFIG_I: Configured from console by console 05:56:08: %SYS-5-CONFIG_I: Configured from console by console RACK9AS>7 [Resuming connection 7 to r7 ... ] R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#no ip pim rp-address 180.40.7.129 1 R7(config)#! R7(config)#no access-list 1 deny 224.20.68.1 R7(config)#! R7(config)# R7(config)#end R7#^Z R7# *Mar 1 05:52:56.268: %SYS-5-CONFIG_I: Configured from console by console R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#no ip pim rp-address 180.40.7.129 1 R3(config)#! R3(config)# R3(config)#! R3(config)# R3(config)#end~ ^ % Invalid input detected at '^' marker. R3(config)#end~  R3# *Mar 1 05:53:19.158: %SYS-5-CONFIG_I: Configured from console by console R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] : Configured from console by console R2# R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim se R2(config)#ip pim send-rp-? send-rp-announce send-rp-discovery R2(config)#ip pim send-rp-d R2(config)#ip pim send-rp-discovery ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing scope Scope of the RP discovery packets R2(config)#ip pim send-rp-discovery 2 ^ % Invalid input detected at '^' marker. R2(config)#ip pim send-rp-discovery 2 sc R2(config)#ip pim send-rp-discovery scope 2 R2(config)#^Z R2#s *Mar 1 05:58:36.899: %SYS-5-CONFIG_I: Configured from console by console R2#sh ru n  n | i ip pim send ip pim send-rp-discovery scope 2 R2# R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pim se R3(config)#ip pim send-rp-a R3(config)#ip pim send-rp-announce ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config)#ip pim send-rp-announce fa 0/0 1 ? scope RP announcement scope R3(config)#ip pim send-rp-announce fa 0/1 sc R3(config)#ip pim send-rp-announce fa 0/1 scope ? <1-255> TTL of the RP announce packet R3(config)#ip pim send-rp-announce fa 0/1 scope 1 2 ? group-list Group access-list interval RP announcement interval R3(config)#ip pim send-rp-announce fa 0/1 scope 2 gr R3(config)#ip pim send-rp-announce fa 0/1 scope 2 group-list ? <1-99> Access-list reference for multicast groups WORD IP Named Standard Access list R3(config)#ip pim send-rp-announce fa 0/1 scope 2 group-list 1 ? interval RP announcement interval R3(config)#ip pim send-rp-announce fa 0/1 scope 2 group-list 1 in R3(config)#ip pim send-rp-announce fa 0/1 scope 2 group-list 1 interval ? <1-16383> number of seconds R3(config)#ip pim send-rp-announce fa 0/1 scope 2 group-list 1 interval 5 R3(config)#^Z R3# *Mar 1 06:00:48.555: %SYS-5-CONFIG_I: Configured from console by console R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip pim rp map PIM Group-to-RP Mappings This system is an RP-mapping agent Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.129 (?), elected via Auto-RP Uptime: 00:01:35, expires: 00:00:14 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.129 (?), elected via Auto-RP Uptime: 00:01:35, expires: 00:00:14 R2# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#config tsh ip mroup 224.20.68.1ing 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 124 ms R7#ping 224.4.4.4config t sh ip mroup 224.20.68.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 113 ms Reply to request 0 from 180.40.7.130, 149 ms Reply to request 0 from 180.40.7.130, 133 ms R7# R7# R7#p 224.20.68.1 RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#config tsh ip mrout IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:11:50/stopped, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:11:50/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:11:50/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:11:50/00:00:00 (17.100.1.2, 224.20.68.1), 00:00:08/00:02:56, flags: T Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Serial1/2, Prune/Sparse-Dense, 00:00:09/00:02:53 FastEthernet0/1, Forward/Sparse-Dense, 00:00:09/00:00:00 (*, 224.4.4.4), 00:08:39/00:03:17, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:08:39/00:03:17 --More--  (17.100.1.2, 224.4.4.4), 00:00:23/00:02:36, flags: Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:23/00:03:09 (*, 224.5.5.5), 00:02:19/00:03:09, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:02:19/00:03:09 (*, 224.0.1.39), 00:08:44/stopped, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:08:44/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:08:44/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:08:45/00:00:00 (180.40.7.129, 224.0.1.39), 00:02:19/00:02:55, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Prune/Sparse-Dense, 00:02:09/00:00:53, A Serial1/0, Forward/Sparse-Dense, 00:02:19/00:00:00 --More--   R3#sh run | b send ip pim send-rp-announce FastEthernet0/1 scope 2 group-list 1 interval 5 ! access-list 1 deny 224.20.68.1 access-list 1 permit any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end --More--   R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] *\ ^ % Invalid input detected at '^' marker. R1# R1# R1# R1#)nfig t ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do sh access-list R1(config)#aacces     ccess-list 1 den 224.20.7e3.1 15.128.20.03.1 15.128.20.0 3.1 15.128.20.0 R1(config)#access-list 1 per any R1(config)#int e 0/0 R1(config-if)#ip igm R1(config-if)#ip igmp ? access-group IGMP group access group explicit-tracking Enable/Disable IGMP explicit-tracking helper-address IGMP helper address immediate-leave Leave groups immediately without sending last member query, use for one host network only join-group IGMP join multicast group last-member-query-count IGMP last member query count last-member-query-interval IGMP last member query interval limit IGMP limit mroute-proxy Mroute to IGMP proxy proxy-service Enable IGMP mroute proxy service querier-timeout IGMP previous querier timeout query-interval IGMP host query interval query-max-response-time IGMP max query response value static-group IGMP static multicast group unidirectional-link IGMP unidirectional link multicast routing v3lite Enable/disable IGMPv3 Lite version IGMP version R1(config-if)#ip igmp access-group ? <1-99> Access list number WORD IP Named Standard Access list R1(config-if)#ip igmp access-group 1 ? R1(config-if)#ip igmp access-group 1 R1(config-if)#^Z R1# RACK9AS>5 [Resuming connection 5 to r5 ... ] 05:5 S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#do sh run ? LINE S5(config)#do sh run int fa 0/2 1 Building configuration... Current configuration : 142 bytes ! interface FastEthernet0/1 no switchport ip address 17.57.100.2 255.255.255.0 ip pim sparse-dense-mode ip igmp join-group 224.5.5.5 end S5(config)#confi gt ^ % Invalid input detected at '^' marker. S5(config)#oc  int fa 0/1 S5(config-if)#ip igmp jo S5(config-if)#ip igmp join-group 224.20.73.1 S5(config-if)#^Z S5# 06:23:35: %SYS-5-CONFIG_I: Configured from console by console S5#config ten config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip igmp join-group 224.20.73.1nt fa 0/1  S5(config-if)#n ip     po  o ip pim sp S5(config-if)#no ip pim sparse-d S5(config-if)#no ip pim sparse-dense-mode S5(config-if)# RACK9AS>7 [Resuming connection 7 to r7 ... ] Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.20.68.1, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 113 ms Reply to request 0 from 180.40.7.130, 145 ms Reply to request 0 from 180.40.7.130, 129 ms R7# R7#p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7#p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7#p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7#sh ip pim p rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:20:45, expires: 00:02:06 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:20:45, expires: 00:02:03 R7#sh ip pim rp mapp 224.5.5.5  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#config t)nfig t config t sh access-list Standard IP access list 1 10 deny 224.20.73.1, wildcard bits 15.128.20.0 (3 matches) 20 permit any (5 matches) R1#ping 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R1# RACK9AS>c 5 [Resuming connection 5 to r5 ... ] S5(config-if)#do sh run int fa 0/1 Building configuration... Current configuration : 148 bytes ! interface FastEthernet0/1 no switchport ip address 17.57.100.2 255.255.255.0 ip igmp join-group 224.5.5.5 ip igmp join-group 224.20.73.1 end S5(config-if)# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh doip mroute ^ % Invalid input detected at '^' marker. R3#sdjh   h ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:02:10/00:03:18, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:02:10/00:03:18 (*, 224.20.68.1), 00:31:33/stopped, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:31:33/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:31:34/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:31:34/00:00:00 (17.100.1.2, 224.20.68.1), 00:01:44/00:01:24, flags: T Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Serial1/2, Prune/Sparse-Dense, 00:01:44/00:01:18 FastEthernet0/1, Forward/Sparse-Dense, 00:01:44/00:00:00 --More--  (*, 224.4.4.4), 00:28:24/00:03:14, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:28:24/00:03:14 (*, 224.5.5.5), 00:21:56/00:03:16, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:21:56/00:03:16 (17.57.100.1, 224.5.5.5), 00:00:18/00:02:41, flags: PX Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (17.100.1.1, 224.5.5.5), 00:00:35/00:02:24, flags: PX Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (17.100.1.2, 224.5.5.5), 00:01:37/00:01:29, flags: PT Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (180.40.7.34, 224.5.5.5), 00:00:35/00:02:29, flags: PT --More--   Incoming interface: Serial1/0, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.0.1.39), 00:28:44/stopped, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:28:44/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:28:44/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:28:44/00:00:00 (180.40.7.129, 224.0.1.39), 00:22:19/00:02:57, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Prune/Sparse-Dense, 00:00:09/00:02:53, A Serial1/0, Forward/Sparse-Dense, 00:22:19/00:00:00 (*, 224.0.1.40), 00:29:48/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:29:48/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:29:48/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:29:48/00:00:00 --More--   R3#clea ip mroute * R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#clea ip mroute *sh ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:00:07/00:02:52, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:07/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:07/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:07/00:00:00 (*, 224.0.1.40), 00:00:09/00:02:55, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:10/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:10/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:10/00:00:00 R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:00:11/00:02:48, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:11/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:11/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:11/00:00:00 (*, 224.4.4.4), 00:00:02/00:02:57, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.0.1.40), 00:00:13/00:02:50, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:13/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:13/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:13/00:00:00 R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:00:02/00:03:27, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:02/00:03:27 (*, 224.20.68.1), 00:00:15/00:02:44, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:15/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:16/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:16/00:00:00 (*, 224.4.4.4), 00:00:07/00:03:26, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:03/00:03:26 (*, 224.5.5.5), 00:00:01/00:03:28, RP 180.40.7.129, flags: S --More--   Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:02/00:03:27 (*, 224.0.1.40), 00:00:19/00:02:44, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:19/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:19/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:19/00:00:00 R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:00:08/00:03:21, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:08/00:03:21 (*, 224.20.68.1), 00:00:22/00:02:37, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:22/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:23/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:23/00:00:00 (*, 224.4.4.4), 00:00:14/00:03:19, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:10/00:03:19 (*, 224.5.5.5), 00:00:07/00:03:22, RP 180.40.7.129, flags: S --More--   Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:08/00:03:21 (*, 224.0.1.40), 00:00:25/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:25/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:25/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:25/00:00:00 (180.40.7.2, 224.0.1.40), 00:00:00/00:02:59, flags: LT Incoming interface: Serial1/2, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:00/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:00:00/00:00:00 (180.40.7.35, 224.0.1.40), 00:00:00/00:02:59, flags: LT Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:00:00/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:00:00/00:00:00 R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:23:00, expires: 00:02:49 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:23:00, expires: 00:02:49 R7#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.5.5.5), 00:02:58/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (17.100.1.1, 224.5.5.5), 00:01:56/00:01:09, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0, Registering Outgoing interface list: Null (17.100.1.2, 224.5.5.5), 00:02:58/00:02:12, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.0.1.40), 00:30:59/00:02:47, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:30:59/00:00:00 R7#sh ip mroutepim rp mapp 224.5.5.5  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 124 ms R7#ping 224.4.4.4              ^Z R7# RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . S6# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#shg    h ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES manual administratively down down BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.98 YES manual up up Serial1/0 unassigned YES manual up up Serial1/0.1 180.40.7.35 YES manual up up Serial1/0.2 180.40.7.65 YES manual up up Serial1/1 unassigned YES manual administratively down down Serial1/2 180.40.7.2 YES manual up up Serial1/3 unassigned YES manual administratively down down --More--   R2#sh run ni  int f s 0/  1/0.1 Building configuration... Current configuration : 267 bytes ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 end R2#sh run int s 1/0.1 2 Building configuration... Current configuration : 175 bytes ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 201 end R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mrou IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:02:21/00:01:09, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.20.68.1), 00:02:34/00:02:30, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:02:34/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:02:34/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:02:35/00:00:00 (*, 224.4.4.4), 00:02:26/00:03:06, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:02:22/00:03:06 (17.100.1.2, 224.4.4.4), 00:01:19/00:01:40, flags: Incoming interface: Serial1/0, RPF nbr 180.40.7.35 --More--   Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:25/00:03:00 (*, 224.5.5.5), 00:02:26/00:03:02, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:02:26/00:03:02 (17.100.1.2, 224.5.5.5), 00:01:38/00:01:21, flags: PX Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (180.40.7.97, 224.5.5.5), 00:01:05/00:01:55, flags: P Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (*, 224.0.1.39), 00:01:36/00:02:24, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:36/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:01:36/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:01:36/00:00:00 --More--   R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int     ^Z R1#sh ip *Mar 1 06:27:04.559: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:05:34/00:00:38, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:05:34/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 00:05:34/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 00:05:34/00:00:00 (*, 224.4.4.4), 00:02:01/stopped, RP 180.40.7.129, flags: SP Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null (17.100.1.2, 224.4.4.4), 00:02:02/00:01:40, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:02:02/00:03:26 (*, 224.5.5.5), 00:33:33/stopped, RP 180.40.7.129, flags: SJCF Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 --More--   Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:33:39/00:02:10 (17.100.1.1, 224.5.5.5), 00:01:10/00:02:22, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:01:10/00:02:22 Ethernet0/0, Forward/Sparse-Dense, 00:01:10/00:02:10 (17.100.1.2, 224.5.5.5), 00:05:32/00:01:15, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:02:21/00:03:20 Ethernet0/0, Forward/Sparse-Dense, 00:05:32/00:02:10 (180.40.7.97, 224.5.5.5), 00:01:47/00:01:24, flags: JT Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:01:47/00:02:10 (*, 224.0.1.39), 00:32:15/stopped, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: --More--   R1# RACK9AS>78 % 78 is not an open connection RACK9AS> [Resuming connection 1 to r1 ... ] R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7#x  RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#shut R1(config-subif)# *Mar 1 06:28:11.568: %PIM-5-NBRCHG: neighbor 180.40.7.33 DOWN on interface Serial0/0.1 (vrf defaul RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1(config-subif)#^Z R1#config tsh ip mrouteconfig t  *Mar 1 06:28:27.567: %SYS-5-CONFIG_I: Configured from console by console R1#config tping 224.5.5.5sh access-list Standard IP access list 1 10 deny 224.20.73.1, wildcard bits 15.128.20.0 (9 matches) 20 permit any (16 matches) R1# R1# R1# R1#deb ip igmp ? Hostname or A.B.C.D IP group address vrf Select VPN Routing/Forwarding instance R1#deb ip igmp IGMP debugging is on R1# *Mar 1 06:29:21.351: IGMP(0): Send v2 general Query on Ethernet0/0 *Mar 1 06:29:21.351: IGMP(0): Set report delay time to 5.8 seconds for 224.0.1.40 on Ethernet0/0 *Mar 1 06:29:22.380: IGMP(0): Send v2 general Query on Ethernet0/1 R1# *Mar 1 06:29:27.449: IGMP(0): Send v2 Report for 224.0.1.40 on Ethernet0/0 *Mar 1 06:29:27.449: IGMP(0): Received v2 Report on Ethernet0/0 from 17.57.100.1 for 224.0.1.40 *Mar 1 06:29:27.449: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 17.57.100.1 for 0 sources *Mar 1 06:29:27.449: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 06:29:27.449: IGMP(0): MRT Add/Update Ethernet0/0 for (*,224.0.1.40) by 0 *Mar 1 06:29:27.982: IGMP(0): Received v2 Report on Ethernet0/0 from 17.57.100.2 for 224.5.5.5 *Mar 1 06:29:27.982: IGMP(0): Received Group record for group 224.5.5.5, mode 2 from 17.57.100.2 for 0 sources R1# *Mar 1 06:29:27.986: IGMP(0): Updating EXCLUDE group timer for 224.5.5.5 *Mar 1 06:29:27.986: IGMP(0): MRT Add/Update Ethernet0/0 for (*,224.5.5.5) by 0 R1# *Mar 1 06:29:29.043: IGMP(0): Received v2 Report on Ethernet0/1 from 17.100.1.2 for 224.0.1.40 *Mar 1 06:29:29.043: IGMP(0): Received Group record for group 224.0.1.40, mode 2 from 17.100.1.2 for 0 sources *Mar 1 06:29:29.043: IGMP(0): Updating EXCLUDE group timer for 224.0.1.40 *Mar 1 06:29:29.043: IGMP(0): MRT Add/Update Ethernet0/1 for (*,224.0.1.40) by 0 R1# *Mar 1 06:29:30.987: IGMP(0): Received v2 Report on Ethernet0/0 from 17.57.100.2 for 224.20.73.1 *Mar 1 06:29:30.987: IGMP(*): Group 224.20.73.1 access denied on Ethernet0/0 R1# *Mar 1 06:29:47.550: IGMP(0): Previous querier timed out, v2 querier for Serial0/0.1 is this systemv2 querier for Serial0/0.1 is this system. R1# *Mar 1 06:29:49.982: IGMP(0): Received v2 Query on Serial0/0.2 from 180.40.7.65 *Mar 1 06:29:50.983: IGMP(0): Received v2 Report on Serial0/0.2 from 180.40.7.65 for 224.0.1.39 *Mar 1 06:29:50.983: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.65 for 0 sources *Mar 1 06:29:50.983: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 06:29:50.983: IGMP(0): MRT Add/Update Serial0/0.2 for (*,224.0.1.39) by 0 R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7#p 224.5.5.5  RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0. /2 S6(config-if)#ip igmp jom n224.67.   6.6.66 224.6.6.6 224.6.6.6 224.6.6.6 i224.6.6.6n224.6.6.6 224.6.6.6 S6(config-if)#^Z S6# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.5.5.5     6.6.66  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 136 ms R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:07:12/00:02:50, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:07:12/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:07:12/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:07:12/00:00:00 (*, 224.4.4.4), 00:07:03/00:03:24, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:07:00/00:03:22 (*, 224.5.5.5), 00:06:58/00:03:27, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:06:58/00:03:27 (*, 224.6.6.6), 00:00:16/stopped, RP 180.40.7.129, flags: S --More--   Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:20/00:03:09 (17.100.1.2, 224.6.6.6), 00:00:13/00:02:46, flags: PX Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (*, 224.0.1.39), 00:06:13/stopped, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:06:13/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:06:13/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:06:13/00:00:00 (180.40.7.129, 224.0.1.39), 00:04:29/00:02:55, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:04:29/00:00:00 (*, 224.0.1.40), 00:07:19/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: --More--   FastEthernet0/1, Forward/Sparse-Dense, 00:07:19/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:07:24/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:07:24/00:00:00 (180.40.7.2, 224.0.1.40), 00:07:00/00:02:57, flags: LT Incoming interface: Serial1/2, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:07:00/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:07:00/00:00:00 (180.40.7.35, 224.0.1.40), 00:07:00/00:02:57, flags: LT Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:07:00/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:07:00/00:00:00 R3#   RACK9AS>7 [Resuming connection 7 to r7 ... ] p 224.6.6.65.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:07:40/00:02:22, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:07:40/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:07:40/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:07:40/00:00:00 (*, 224.4.4.4), 00:07:31/00:02:56, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:07:28/00:02:55 (*, 224.5.5.5), 00:07:26/stopped, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:07:26/00:03:00 (17.100.1.2, 224.5.5.5), 00:00:05/00:02:54, flags: PX --More--   Incoming interface: Serial1/0, RPF nbr 180.40.7.35 --More--   Outgoing interface list: Null --More--   --More--  (*, 224.6.6.6), 00:00:46/stopped, RP 180.40.7.129, flags: S --More--   Incoming interface: Null, RPF nbr 0.0.0.0 --More--   Outgoing interface list: --More--   R3# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:06:41/00:00:11, RP 180.40.7.129, flags: SP Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null (*, 224.5.5.5), 00:38:12/stopped, RP 180.40.7.129, flags: SJCF Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:38:12/00:02:36 (17.100.1.2, 224.5.5.5), 00:10:06/00:03:09, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:00:22/00:03:07 Ethernet0/0, Forward/Sparse-Dense, 00:10:06/00:02:35 (*, 224.6.6.6), 00:00:54/stopped, RP 180.40.7.129, flags: SP Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null --More-- *Mar 1 06:31:50.175: IGMP(0): Received v2 Query on Serial0/0.2 from 180.40.7.65 --More-- *Mar 1 06:31:54.181: IGMP(0): Received v2 Report on Serial0/0.2 from 180.40.7.65 for 224.0.1.39 *Mar 1 06:31:54.181: IGMP(0): Received Group record for group 224.0.1.39, mode 2 from 180.40.7.65 for 0 sources *Mar 1 06:31:54.181: IGMP(0): Updating EXCLUDE group timer for 224.0.1.39 *Mar 1 06:31:54.181: IGMP(0): MRT Add/Update Serial0/0.2 for (*,224.0.1.39) by 0 --More--   R1#u alkl  l All possible debugging has been turned off R1#q x5 Translating "x5" Translating "x5" % Unknown command or computer name, or unable to find computer address R1# R1# RACK9AS>5 [Resuming connection 5 to r5 ... ] S5(config-if)#do sh ip o route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.57.100.0 is directly connected, FastEthernet0/1 O 17.100.1.0 [110/20] via 17.57.100.1, 00:04:35, FastEthernet0/1 O 192.10.32.0/24 [110/857] via 17.57.100.1, 00:04:35, FastEthernet0/1 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.128/27 [110/856] via 17.57.100.1, 00:04:35, FastEthernet0/1 O 180.40.7.0/27 [110/855] via 17.57.100.1, 00:04:35, FastEthernet0/1 O 180.40.7.35/32 [110/74] via 17.57.100.1, 00:04:35, FastEthernet0/1 O 180.40.7.33/32 [110/855] via 17.57.100.1, 00:04:35, FastEthernet0/1 O 180.40.7.66/32 [110/10] via 17.57.100.1, 00:04:35, FastEthernet0/1 O 180.40.7.65/32 [110/74] via 17.57.100.1, 00:04:35, FastEthernet0/1 O 180.40.7.96/27 [110/75] via 17.57.100.1, 00:04:35, FastEthernet0/1 S5(config-if)#do p 17.100.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 17.100.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5(config-if)#^Z S5# 06:36:30: %SYS-5-CONFIG_I: Configured from console by console S5#deb ip mrou    m  poa  a IP multicast packets debugging is on S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#logg buff S5(config)#^Z S5# 06:36:44: %SYS-5-CONFIG_I: Conf RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: RACK9AS>6 5 [Resuming connection 5 to r5 ... ] igured from console by console S5# S5#sh logg Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) Console logging: level debugging, 55 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 55 messages logged, xml disabled, filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled File logging: disabled Trap logging: level informational, 58 message lines logged --More--   Log Buffer (4096 bytes): -5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down 00:01:02: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up 00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up 00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up 00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to up --More--  00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/8, changed state to up 00:01:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up 00:01:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up 00:01:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to up 00:01:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to up 00:01:10: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 00:01:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up 00:01:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down 00:01:13: %LINK-5-CHANGED: Interface FastEthernet0/24, changed state to administratively down 00:01:15: %SYS-5-CONFIG_I: Configured from console by console 00:03:09: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.66 on FastEthernet0/1 from LOADING to FULL, Loading Done 00:03:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down 00:03:19: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down --More--  00:03:19: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down 00:03:20: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down 00:03:22: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up 00:03:23: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up 00:03:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up 00:03:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up 00:03:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down 00:03:28: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to down 00:03:31: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to up 00:03:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down 00:03:32: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down 00:03:32: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down 00:03:33: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down 00:03:33: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to up 00:03:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down 00:03:41: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to down --More--  05:25:08: %SYS-5-CONFIG_I: Configured from console by console 05:33:56: %SYS-5-CONFIG_I: Configured from console by console 05:51:37: %SYS-5-CONFIG_I: Configured from console by console 05:56:03: %SYS-5-CONFIG_I: Configured from console by console 06:23:35: %SYS-5-CONFIG_I: Configured from console by console 06:36:30: %SYS-5-CONFIG_I: Configured from console by console 06:36:44: %SYS-5-CONFIG_I: Configured from console by console S5#       RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh    sh ip mro ute Translating "ute" ^ % Invalid input detected at '^' marker. R1#sh ip mro uteute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.5.5.5), 00:41:40/stopped, RP 180.40.7.129, flags: SJCF Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:41:40/00:02:11 (17.100.1.2, 224.5.5.5), 00:13:33/00:02:15, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:13:33/00:02:11 (*, 224.6.6.6), 00:04:22/00:02:20, RP 180.40.7.129, flags: SP Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null (*, 224.0.1.39), 00:40:17/00:02:43, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:40:17/00:00:00 --More--   R1# RACK9AS>6 [Resuming connection 6 to r6 ... ] 0 S6#config tping 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . S6# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip mroute uteute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.5.5.5), 00:43:06/stopped, RP 180.40.7.129, flags: SJCF Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:43:06/00:02:47 (17.100.1.2, 224.5.5.5), 00:14:59/00:00:51, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:14:59/00:02:47 (180.40.7.97, 224.5.5.5), 00:00:12/00:02:56, flags: JT Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:00:12/00:02:48 (*, 224.6.6.6), 00:05:48/00:00:56, RP 180.40.7.129, flags: SP Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null --More--   R1# RACK9AS>54 % 54 is not an open connection RACK9AS>5 [Resuming connection 5 to r5 ... ] S5#sh logg Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) Console logging: level debugging, 55 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 55 messages logged, xml disabled, filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled File logging: disabled Trap logging: level informational, 58 message lines logged --More--   Log Buffer (4096 bytes): -5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down 00:01:02: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to down 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up 00:01:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up 00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up 00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up 00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to up --More--  00:01:04: %LINK-3-UPDOWN: Interface FastEthernet0/8, changed state to up 00:01:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up 00:01:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up 00:01:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to up 00:01:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to up 00:01:10: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 00:01:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up 00:01:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down 00:01:13: %LINK-5-CHANGED: Interface FastEthernet0/24, changed state to administratively down 00:01:15: %SYS-5-CONFIG_I: Configured from console by console 00:03:09: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.66 on FastEthernet0/1 from LOADING to FULL, Loading Done 00:03:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down 00:03:19: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down --More--  00:03:19: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down 00:03:20: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down 00:03:22: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up 00:03:23: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up 00:03:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up 00:03:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up 00:03:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down 00:03:28: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to down 00:03:31: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to up 00:03:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down 00:03:32: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down 00:03:32: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down 00:03:33: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down 00:03:33: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to up 00:03:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down 00:03:41: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to down --More--  05:25:08: %SYS-5-CONFIG_I: Configured from console by console 05:33:56: %SYS-5-CONFIG_I: Configured from console by console 05:51:37: %SYS-5-CONFIG_I: Configured from console by console 05:56:03: %SYS-5-CONFIG_I: Configured from console by console 06:23:35: %SYS-5-CONFIG_I: Configured from console by console 06:36:30: %SYS-5-CONFIG_I: Configured from console by console 06:36:44: %SYS-5-CONFIG_I: Configured from console by console S5# ce l;ea   ea logg Clear logging buffer [confirm] S5# RACK9AS>21 % 21 is not an open connection RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/0 R1(config-if)#int e 0/0shut int s 0/0.1p igmp access-group 1 nip igmp access-group 1 oip igmp access-group 1  ip igmp access-group 1  R1(config-if)# RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . S6# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)#shut R1(config-if)#no *Mar 1 06:37:42.909: %OSPF-5-ADJCHG: Process 1, Nbr 17.57.100.2 on Ethernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R1(config-if)#no shut R1(config-if)# *Mar 1 06:37:44.908: %LINK-5-CHANGED: Interface Ethernet0/0, changed state to administratively down *Mar 1 06:37:45.910: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to down R1(config-if)# *Mar 1 06:37:47.344: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.57.100.1 on interface Ethernet0/0 (vrf default) R1(config-if)# *Mar 1 06:37:48.162: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up *Mar 1 06:37:49.163: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up R1(config-if)#^Z R1# *Mar 1 06:37:54.680: %SYS-5-CONFIG_I: Configured from console by console R1# *Mar 1 06:37:56.195: %OSPF-5-ADJCHG: Process 1, Nbr 17.57.100.2 on Ethernet0/0 from LOADING to FULL, Loading Done R1# RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . S6# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh run int e 0/0 Building configuration... Current configuration : 106 bytes ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode half-duplex end R1#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.73.1), 00:00:41/00:02:49, RP 180.40.7.129, flags: SJC Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:00:41/00:02:49 (*, 224.5.5.5), 00:44:53/stopped, RP 180.40.7.129, flags: SJCF Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:00:42/00:02:44 (180.40.7.97, 224.5.5.5), 00:01:59/00:02:40, flags: JT Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:00:42/00:02:44 (*, 224.0.1.39), 00:43:31/00:02:23, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: --More--   Serial0/0.2, Forward/Sparse-Dense, 00:43:31/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 00:43:49/00:00:00 (*, 224.0.1.40), 00:45:22/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:45:22/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 00:45:22/00:00:00 (180.40.7.65, 224.0.1.40), 00:37:24/00:02:24, flags: LT Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/1, Forward/Sparse-Dense, 00:37:24/00:00:00 R1# RACK9AS>5 [Resuming connection 5 to r5 ... ] 06:40 clea loggsh logg  Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) Console logging: level debugging, 56 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 56 messages logged, xml disabled, filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled File logging: disabled Trap logging: level informational, 59 message lines logged --More--   Log Buffer (4096 bytes): 06:40:24: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.66 on FastEthernet0/1 from LOADING to FULL, Loading Done S5# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#deb ip mroute ^ % Invalid input detected at '^' marker. R1#deb ip mroute     pack IP multicast packets debugging is on R1# RACK9AS>5 6 [Resuming connection 6 to r6 ... ] ping 224.5.5.5 re 100 Type escape sequence to abort. Sending 100, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 129 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: disabled, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 62 message lines logged R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#^Z R1#sh ip *Mar 1 06:39:42.401: %SYS-5-CONFIG_I: Configured from console by console R1#sh ip int s 0/0.2 Serial0/0.2 is up, line protocol is up Internet address is 180.40.7.66/27 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Multicast reserved groups joined: 224.0.0.5 224.0.0.1 224.0.0.2 224.0.0.22 224.0.0.13 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is enabled IP Flow switching is disabled IP CEF switching is enabled IP CEF Fast switching turbo vector --More--   IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is disabled WCCP Redirect outbound is disabled WCCP Redirect inbound is disabled WCCP Redirect exclude is disabled BGP Policy Mapping is disabled R1#1 config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0./  /0.2 R1(config-subif)#no ip mr R1(config-subif)#no ip mro   *Mar 1 06:40:09.401: IP(0): s=180.40.7.65 (Serial0/0.2) d=224.0.1.40 (Ethernet0/1) id=8365, prot=17, len=54(54), mforward R1(config-subif)#no ip m? mask-reply mobile mrm mroute-cache mtu multicast R1(config-subif)#no ip mu R1(config-subif)#no ip multicast ? boundary Boundary for administratively scoped multicast addresses helper-map Broadcast to Multicast map OR Multicast to ip-address map netflow NetFlow accounting for multicast rate-limit Rate limit multicast data packets tagswitch Enable IP Multicast Tagswitching ttl-threshold TTL threshold for multicast packets R1(config-subif)#no ip multicast          r R1(config-subif)#no ip mr? mrm mroute-cache R1(config-subif)#no ip mrou R1(config-subif)#no ip mroute-cache R1(config-subif)#int e 0/0 R1(config-if)# *Mar 1 06:40:27.146: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=38, prot=1, len=100(100), mforward R1(config-if)#int e 0/0no ip mroute-cache R1(config-if)#^Z R1# *Mar 1 06:40:29.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=39, prot=1, len=100(100), mforward R1# *Mar 1 06:40:29.390: %SYS-5-CONFIG_I: Configured from console by console R1# *Mar 1 06:40:31.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=40, prot=1, len=100(100), mforward R1# *Mar 1 06:40:33.148: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=41, prot=1, len=100(100), mforward R1# *Mar 1 06:40:35.147: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=42, prot=1, len=100(100), mforward R1# *Mar 1 06:40:37.147: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=43, prot=1, len=100(100), mforward R1# R1# R1# *Mar 1 06:40:39.146: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=44, prot=1, len=100(100), mforward R1# RACK9AS>6 [Resuming connection 6 to r6 ... ] ...... RACK9AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/1 S5(config-if)#i no ip mrou S5(config-if)#no ip mroute-cache S5(config-if)#^Z S5# 06:43:30: %SYS-5-CONFIG_I: Configured from console by console S5#sh deb Generic IP: IP multicast packets debugging is on S5# S5# S5# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1# *Mar 1 06:41:45.146: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=77, prot=1, len=100(100), mforward R1# *Mar 1 06:41:47.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=78, prot=1, len=100(100), mforward R1# *Mar 1 06:41:49.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=79, prot=1, len=100(100), mforward R1# *Mar 1 06:41:51.144: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=80, prot=1, len=100(100), mforward R1# *Mar 1 06:41:53.147: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=81, prot=1, len=100(100), mforward R1# *Mar 1 06:41:55.146: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=82, prot=1, len=100(100), mforward R1# *Mar 1 06:41:57.146: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=83, prot=1, len=100(100), mforward R1# *Mar 1 06:41:59.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=84, prot=1, len=100(100), mforward R1# *Mar 1 06:42:01.172: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=85, prot=1, len=100(100), mforward R1# *Mar 1 06:42:03.144: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=86, prot=1, len=100(100), mforward R1# *Mar 1 06:42:05.147: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=87, prot=1, len=100(100), mforward R1# *Mar 1 06:42:07.146: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=88, prot=1, len=100(100), mforward *Mar 1 06:42:07.591: IP(0): s=180.40.7.65 (Serial0/0.2) d=224.0.1.40 (Ethernet0/1) id=8464, prot=17, len=54(54), mforward R1# *Mar 1 06:42:09.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=89, prot=1, len=100(100), mforward R1# *Mar 1 06:42:11.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=90, prot=1, len=100(100), mforward R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int *Mar 1 06:42:13.176: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=91, prot=1, len=100(100), mforward R1(config)#int e 0/0 *Mar 1 06:42:15.163: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=92, prot=1, len=100(100), mforward R1(config)#int e 0/0 R1(config-if)#int e 0/0no ip mroute-cache int e 0/0 no ip mroute-cache *Mar 1 06:42:17.163: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=93, prot=1, len=100(100), mforward R1(config-if)#no ip mroute-cache int s 0/0.2 no shut shut  *Mar 1 06:42:19.150: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=94, prot=1, len=100(100), mforward R1(config-if)#shutno ip igmp access-group 1 n *Mar 1 06:42:21.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=95, prot=1, len=100(100), mforward R1(config-if)#no ip igmp access-group 1 o ip igmp access-group 1  ip igmp access-group 1  R1(config-if)# *Mar 1 06:42:23.144: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=96, prot=1, len=100(100), mforward R1(config-if)#ip *Mar 1 06:42:25.144: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=97, prot=1, len=100(100), mforward R1(config-if)#ip mrou R1(config-if)#ip mroute-cache R1(config-if)# *Mar 1 06:42:27.147: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=98, prot=1, len=100(100), mforward R1(config-if)#int s 0/0.2 *Mar 1 06:42:29.146: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=99, prot=1, len=100(100), mforward R1(config-if)#int s 0/0.2p mroute-cache  ip igmp access-group 1 R1(config-if)# *Mar 1 06:42:31.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=100, prot=1, len=100(100), mforward R1(config-if)# ip igmp access-group 1 n ip igmp access-group 1 o ip igmp access-group 1  ip igmp access-group 1  *Mar 1 06:42:33.145: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=101, prot=1, len=100(100), mforward R1(config-if)#no ip igmp access-group 1  R1(config-if)#no ip igmp access-group 1  ip igmp access-group 1 ip mroute-cache  *Mar 1 06:42:35.152: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 (Ethernet0/0) id=102, prot=1, len=100(100), mforward R1(config-if)#ip mroute-cache R1(config-if)#^Z R1# *Mar 1 06:42:37.147: IP(0): s=180.40.7.97 (Serial0/0.2) d=224.5.5.5 RACK9AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/1 S5(config-if)# S5(config-if)# S5(config-if)#int fa 0/1no ip mroute-cache no ip mroute-cache  ip mroute-cache  S5(config-if)#^Z S5# 06:45:23: %SYS-5-CONFIG_I: Configured from console by console S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int f 0/1 S5(config-if)#ip pim S5(config-if)#ip pim sp S5(config-if)#ip pim sparse-d S5(config-if)#ip pim sparse-dense-mode S5(config-if)#^Z S5# 06:46:11 RACK9AS>6 [Resuming connection 6 to r6 ... ] .. S6#ping 224.5.5.5 re 100       Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: Reply to request 0 from 17.57.100.2, 60 ms S6# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Mar 1 0 R1#sh run ~ | b 0/0 interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point shutdown frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint no ip mroute-cache frame-relay interface-dlci 102 ! --More--  interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim sparse-dense-mode half-duplex no keepalive ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! ! access-list 1 deny 224.20.73.1 15.128.20.0 access-list 1 permit any ! ! ! --More-- *Mar 1 06:45:06.881: IP(0): s=180.40.7.65 (Serial0/0.2) d=224.0.1.40 (Ethernet0/0) id=8647, prot=17, len=54(54), mforward *Mar 1 06:45:06.881: IP(0): s=180.40.7.65 (Serial0/0.2) d=224.0.1.40 (Ethernet0/1) id=8647, prot=17, len=54(54), mforward --More--   R1#u all All possible debugging has been turned off R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/0 R1(config-if)#int e 0/0p mroute-cache no ip igmp access-group 1  ip igmp access-group 1 ip mroute-cache  ip igmp access-group 1 R1(config-if)#^Z R1#sh run *Mar 1 06:45:59.751: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int e 0/1 Building configuration... Current configuration : 119 bytes ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim sparse-dense-mode half-duplex no keepalive end R1#sh run int e 0/1 sh run int e 0/1config t u all config tsh run int e 0/1 0 Building configuration... Current configuration : 130 bytes ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip igmp access-group 1 half-duplex end R1# R1#congfig      fig t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0? / R1(config)#int e 00 ip igmp access-group 1 int e 0/0  ip igmp access-group 1 int e 0/0  R1(config-if)#ip mu R1(config-if)#ip multicast ? boundary Boundary for administratively scoped multicast addresses helper-map Broadcast to Multicast map OR Multicast to ip-address map netflow NetFlow accounting for multicast rate-limit Rate limit multicast data packets tagswitch Enable IP Multicast Tagswitching ttl-threshold TTL threshold for multicast packets R1(config-if)#ip multicast reate      ate ? in Rate limit incoming packets out Rate limit outgoing packets R1(config-if)#ip multicast rate out ? <0-4294967> Rate in kilobits per second group-list Rate limit for groups source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate out vi ? <0-4294967> Rate in kilobits per second R1(config-if)#ip multicast rate out vi 80 ? R1(config-if)#ip multicast rate out vi 80       =                       exit R1(config)#access-0  -; list 2 den     per 239.0.0.0 0.255.255.255 R1(config)#int e 0/0 R1(config-if)#ip mu R1(config-if)#ip multicast ra R1(config-if)#ip multicast rate-limit ? in Rate limit incoming packets out Rate limit outgoing packets R1(config-if)#ip multicast rate-limit out ? <0-4294967> Rate in kilobits per second group-list Rate limit for groups source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit out gr R1(config-if)#ip multicast rate-limit out group-list 2 ? <0-4294967> Rate in kilobits per second source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit out group-list 2 vi R1(config-if)#ip multicast rate-limit out group-list 2 video 80 ? R1(config-if)#ip multicast rate-limit out group-list 2 video 80 R1(config-if)#^Z R1#sh ru *Mar 1 06:47:48.862: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int e 00 /0 Building configuration... Current configuration : 181 bytes ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip multicast rate-limit out group-list 2 video 80 ip igmp access-group 1 half-duplex end R1# R1#coni fig t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#int e 0/1p multicast rate-limit out group-list 2 video 80 nt e 0/0  R1(config-if)#int e 0/01p multicast rate-limit out group-list 2 video 80 R1(config-if)#ip multicast rate-limit out group-list 2 video 80  group-list 2 video 80  group-list 2 video 80  group-list 2 video 80 i group-list 2 video 80 n group-list 2 video 80  R1(config-if)#ip multicast rate-limit in group-list 2 video 80 out group-list 2 video 80 nip multicast rate-limit out group-list 2 video 80 oip multicast rate-limit out group-list 2 video 80  ip multicast rate-limit out group-list 2 video 80  R1(config-if)#do sh ru nint     n int e 0/0 Building configuration... Current configuration : 180 bytes ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip multicast rate-limit in group-list 2 video 80 ip igmp access-group 1 half-duplex end R1(config-if)# R1# *Mar 1 06:52:07.695: %SYS-5-CONFIG_I: Configured from console by console R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ip ig R1(config-if)#ip igmp ? access-group IGMP group access group explicit-tracking Enable/Disable IGMP explicit-tracking helper-address IGMP helper address immediate-leave Leave groups immediately without sending last member query, use for one host network only join-group IGMP join multicast group last-member-query-count IGMP last member query count last-member-query-interval IGMP last member query interval limit IGMP limit mroute-proxy Mroute to IGMP proxy proxy-service Enable IGMP mroute proxy service querier-timeout IGMP previous querier timeout query-interval IGMP host query interval query-max-response-time IGMP max query response value static-group IGMP static multicast group unidirectional-link IGMP unidirectional link multicast routing v3lite Enable/disable IGMPv3 Lite version IGMP version R1(config-if)#ip igmp qu R1(config-if)#ip igmp queri R1(config-if)#ip igmp querier-timeout               R1(config-if)#ip igmp query R1(config-if)#ip igmp query-i R1(config-if)#ip igmp query-interval ? <1-18000> Query interval in seconds R1(config-if)#ip igmp query-interval 90 R1(config-if)#ip piom qy  R1(config-if)#ip piom q    m R1(config-if)#ip pim qu R1(config-if)#ip pim query-interval 90 R1(config-if)#^Z R1#sh run int *Mar 1 06:57:26.854: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int e 0/1 Building configuration... Current configuration : 172 bytes ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim query-interval 90 ip pim sparse-dense-mode ip igmp query-interval 90 half-duplex no keepalive end R1# R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] . R *Mar 1 06:57:10.515: %PIM-5-NBRCHG: neighbor 17.100.1.1 UP on interface FastEthernet0/1 (vrf default) R7# R7#sh ip pim int Address Interface Ver/ Nbr Query DR DR Mode Count Intvl Prior 17.100.1.2 FastEthernet0/1 v2/SD 1 30 1 17.100.1.2 R7#sh ip pim int  de FastEthernet0/1 is up, line protocol is up Internet address is 17.100.1.2/24 Multicast switching: fast Multicast packets in/out: 17/0 Multicast boundary: not set Multicast TTL threshold: 0 PIM: enabled PIM version: 2, mode: sparse-dense PIM DR: 17.100.1.2 (this system) PIM neighbor count: 1 PIM Hello/Query interval: 30 seconds PIM State-Refresh processing: enabled PIM State-Refresh origination: disabled PIM NBMA mode: disabled PIM ATM multipoint signalling: disabled PIM domain border: disabled Multicast Tagswitching: disabled R7#sh clock *06:57:52.576 UTC Mon Mar 1 1993 R7#sh clock *06:58:25.389 UTC Mon Mar 1 1993 R7#sh clock *06:59:04.141 UTC Mon Mar 1 1993 R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh run int e 0/1config t sh run int e 0/1 Building configuration... Current configuration : 172 bytes ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim query-interval 90 ip pim sparse-dense-mode ip igmp query-interval 90 half-duplex no keepalive end R1# R1# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#config tsh run int fa 0/0config t u all deb ip pack deim sh ip pim int fa 0/0 detail config t sh run | b ip mulconfig t en   p 224.5.5.5.  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R4#p 224.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . R4# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#shg    ip igp gr R7#sh ip igp gr ^ % Invalid input detected at '^' marker. R7#sh ip igp gr    m gr IGMP Connected Group Membership Group Address Interface Uptime Expires Last Reporter 224.0.1.40 FastEthernet0/1 01:38:14 00:02:11 17.100.1.2 R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#ip igmp jo 224.7.7.7 R7(config-if)#^Z R7# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#p 244  24.8 7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 108 ms R4# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#clea      config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 09  0/13  R3(config-if)#ip pim de R3(config-if)#ip pim dense-mode R3(config-if)#^Z R3#cl *Mar 1 07:01:52.813: %SYS-5-CONFIG_I: Configured from console by console R3#clea ip mrou * R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 104 ms R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 120 ms R4#dh    sh i mroute % Ambiguous command: "sh i mroute" R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 01:11:24/00:02:52, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 01:11:24/00:00:00 (*, 224.4.4.4), 01:38:14/00:02:53, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.5.5.5), 00:01:52/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (180.40.7.130, 224.5.5.5), 00:01:52/00:01:11, flags: PFT Incoming interface: FastEthernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.7.7.7), 00:01:10/stopped, RP 180.40.7.129, flags: SPF --More--   Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (180.40.7.130, 224.7.7.7), 00:01:15/00:02:40, flags: PFT Incoming interface: FastEthernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.0.1.39), 01:01:49/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 01:01:49/00:00:00 (180.40.7.129, 224.0.1.39), 00:01:19/00:01:40, flags: PT Incoming interface: FastEthernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.0.1.40), 01:41:09/00:02:43, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 01:41:09/00:00:00 R4#q  RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh ouip mroute ^ % Invalid input detected at '^' marker. R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1572] via 180.40.7.35, 00:25:29, Serial1/0 [110/1572] via 180.40.7.2, 00:25:29, Serial1/2 O 17.100.1.0 [110/1572] via 180.40.7.35, 00:25:29, Serial1/0 [110/1572] via 180.40.7.2, 00:25:29, Serial1/2 O 192.10.32.0/24 [110/2] via 180.40.7.130, 00:25:29, FastEthernet0/1 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/1 C 180.40.7.0/27 is directly connected, Serial1/2 O 180.40.7.35/32 [110/781] via 180.40.7.2, 00:25:31, Serial1/2 [110/781] via 180.40.7.35, 00:25:31, Serial1/0 C 180.40.7.32/27 is directly connected, Serial1/0 O 180.40.7.66/32 [110/1562] via 180.40.7.35, 00:25:31, Serial1/0 --More--   R3#[Ash ip routemroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:00:44/00:02:15, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:44/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:44/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:44/00:00:00 (*, 224.4.4.4), 00:00:43/00:03:09, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:44/00:00:00 (*, 224.6.6.6), 00:00:25/00:03:04, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:25/00:03:04 FastEthernet0/1, Forward/Dense, 00:00:25/00:00:00 --More--  (*, 224.7.7.7), 00:01:07/00:02:30, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:59/00:02:30 FastEthernet0/1, Forward/Dense, 00:01:07/00:00:00 (180.40.7.130, 224.7.7.7), 00:01:07/00:02:46, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:59/00:02:30 (*, 224.0.1.39), 00:01:07/stopped, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:01:07/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:01:07/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:01:07/00:00:00 (180.40.7.129, 224.0.1.39), 00:01:07/00:02:56, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:01:07/00:00:00 --More--   R3#clea ip m  route ( * R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#clea ip mrout * R4#clea ip mrout *sh ip mroute  mroute p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 136 ms R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:01:39/00:02:57, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:01:39/00:00:00 (*, 224.4.4.4), 00:01:39/00:02:02, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.7.7.7), 00:01:37/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (180.40.7.130, 224.7.7.7), 00:01:37/00:02:51, flags: PFT Incoming interface: FastEthernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.0.1.39), 00:01:38/stopped, RP 0.0.0.0, flags: D --More--   R4#sh run int f a0/0 ^ % Invalid input detected at '^' marker. R4#sh run int f a0/00/0 0/0  Building configuration... Current configuration : 241 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 88 ip pim dense-mode ip igmp join-group 224.4.4.4 ip igmp join-group 224.20.68.1 duplex auto speed auto end R4# RACK9AS>z3  3 [Resuming connection 3 to r3 ... ] R3#sh run fint fa 0? % Unrecognized command R3#sh run fint fa 01 /1int fa 0/1  Building configuration... Current configuration : 118 bytes ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim dense-mode duplex auto speed auto end R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 01:07:33, expires: 00:02:53 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 01:07:33, expires: 00:02:54 R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#access-list 1 dny any ^ % Invalid input detected at '^' marker. R4(config)#access-list 1 dny any any  any  R4(config)#access-list 1 d any ip pim rp R4(config)#ip pim rp-? rp-address rp-announce-filter rp-candidate R4(config)#ip pim rp-  ? % Ambiguous command: "ip pim rp " R4(config)#ip pim rp    ? accept-register Registers accept filter accept-rp RP accept filter autorp Configure AutoRP global operations bidir-enable Enable Bidir-PIM bsr-candidate Candidate bootstrap router (candidate BSR) log-neighbor-changes Log PIM neighbor up/down and DR changes register-rate-limit Rate limit for PIM data registers register-source Source address for PIM Register rp-address PIM RP-address (Rendezvous Point) rp-announce-filter Auto-RP announce message filter rp-candidate To be a PIMv2 RP candidate send-rp-announce Auto-RP send RP announcement send-rp-discovery Auto-RP send RP discovery message (as RP-mapping agent) spt-threshold Source-tree switching threshold ssm Configure Source Specific Multicast state-refresh PIM DM State-Refresh configuration vrf Select VPN Routing/Forwarding instance R4(config)#ip pim acc R4(config)#ip pim accept-r? accept-register accept-rp R4(config)#ip pim accept-r rp ? A.B.C.D IP address of RP for group auto-rp only RP-mapping from Auto-RP R4(config)#ip pim accept-rp au R4(config)#ip pim accept-rp auto-rp ? <1-99> Access-list reference for group <1300-1999> Access-list reference for group (expanded range) WORD IP Named Standard Access list R4(config)#ip pim accept-rp auto-rp 1 ? R4(config)#ip pim accept-rp auto-rp 1 R4(config)#^Z R4#config t *Mar 1 07:12:20.774: %SYS-5-CONFIG_I: Configured from console by console R4#config tsh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 01:09:18, expires: 00:02:07 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 01:09:18, expires: 00:02:08 R4#clea ip pim rp * ^ % Invalid input detected at '^' marker. R4#clea ip pim rp *   map * ^ % Invalid input detected at '^' marker. R4#clea ip pim rp map *     ? A.B.C.D RP address R4#clea ip pim rp R4#clea ip pim rp map ** sh ip pim rp mapclea ip pim rp *sh ip pim rp mapclea ip pim rp *sh ip pim rp mapconfig t sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp mapclea ip pim rp map ** sh ip pim rp mapconfig t sh ip pim rp maprun int f0/0  a0/0ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.20.68.1), 00:07:17/00:02:15, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:07:17/00:00:00 (*, 224.4.4.4), 00:01:02/00:02:15, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:01:02/00:00:00 (*, 224.0.1.39), 00:07:17/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:07:17/00:00:00 (180.40.7.129, 224.0.1.39), 00:01:16/00:01:43, flags: PT Incoming interface: FastEthernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Null --More--   (*, 224.0.1.40), 00:07:20/00:02:13, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:07:20/00:00:00 R4#sh ip mroutepim rp mapclea ip pim rp sh ip pim rp map PIM Group-to-RP Mappings R4#sh    sh ip pim rp mapmroute pim rp mapclea ip pim rp map ** sh ip pim rp mapconfig t sh ip pim rp maprun int f0/0  a0/0ip mroute p 224.7.7.7  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 116 ms R4#p 224.7.7.7sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:08, expires: 00:02:50 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:08, expires: 00:02:49 R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#acccess    ess-list 2 per 180.40.7.129 R4(config)#ip ? Global IP configuration subcommands: access-list Named access-list accounting-list Select hosts for which IP accounting information is kept accounting-threshold Sets the maximum number of accounting entries accounting-transits Sets the maximum number of transit entries address-pool Specify default IP address pooling mechanism alias Alias an IP address to a TCP port as-path BGP autonomous system path filter audit Intrusion Detection System auth-proxy Authentication Proxy bgp-community format for BGP community bootp Config BOOTP services casa configure this router to participate in casa cef Cisco Express Forwarding classless Follow classless routing forwarding rules community-list Add a community list entry default-gateway Specify default gateway (if not routing IP) default-network Flags networks as candidates for default routes dhcp Configure DHCP server and relay parameters dhcp-client Configure parameters for DHCP client operation dhcp-server Specify address of DHCP server to use --More--   R4(config)#ip rp    pi R4(config)#ip pim ? accept-register Registers accept filter accept-rp RP accept filter autorp Configure AutoRP global operations bidir-enable Enable Bidir-PIM bsr-candidate Candidate bootstrap router (candidate BSR) log-neighbor-changes Log PIM neighbor up/down and DR changes register-rate-limit Rate limit for PIM data registers register-source Source address for PIM Register rp-address PIM RP-address (Rendezvous Point) rp-announce-filter Auto-RP announce message filter rp-candidate To be a PIMv2 RP candidate send-rp-announce Auto-RP send RP announcement send-rp-discovery Auto-RP send RP discovery message (as RP-mapping agent) spt-threshold Source-tree switching threshold ssm Configure Source Specific Multicast state-refresh PIM DM State-Refresh configuration vrf Select VPN Routing/Forwarding instance R4(config)#ip pim rp  -amm  nn R4(config)#ip pim rp-announce-filter ? group-list Group address access-list rp-list RP address access-list R4(config)#ip pim rp-announce-filter r R4(config)#ip pim rp-announce-filter rp-list ? <1-99> Access-list reference for RP WORD IP Named Standard Access list R4(config)#ip pim rp-announce-filter rp-list 2 ? group-list Group address access-list R4(config)#ip pim rp-announce-filter rp-list 2 gr R4(config)#ip pim rp-announce-filter rp-list 2 group-list 1 ? R4(config)#ip pim rp-announce-filter rp-list 2 group-list 1 R4(config)#^Z R4#config tsh ip pim rp map *Mar 1 07:14:42.710: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:01:09, expires: 00:02:49 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:01:09, expires: 00:02:48 R4#clea ip rp map ^ % Invalid input detected at '^' marker. R4#clea ip rp map \      pim rp map ^ % Invalid input detected at '^' marker. R4#clea ip pim rp map     R4#clea ip pim rp maprp map sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp mapclea ip pim rp sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp mapclea ip pim rp  maprp map sh ip pim rp mapconfig t sh ip pim rp mapp 224.7.7.7  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 104 ms R4#clea ip bg  mrou * R4# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int fa 0/1clea ip mroute *  R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#clea ip mrou *p 224.7.7.7 sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:02, expires: 00:02:58 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:02, expires: 00:02:56 R4#sh run | b ip pim rp ip pim rp-announce-filter rp-list 2 group-list 1 ! ! ip access-list standard IPNAT permit 180.40.7.0 0.0.0.255 permit 17.0.0.0 0.255.255.255 access-list 1 deny any access-list 2 permit 180.40.7.129 ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! --More--   R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip pim acc R4(config)#ip pim accept-rp R4(config)#ip pim accept-rp ? A.B.C.D IP address of RP for group auto-rp only RP-mapping from Auto-RP R4(config)#ip pim accept-rp 180.40.7.129 ? <1-99> Access-list reference for group <1300-1999> Access-list reference for group (expanded range) WORD IP Named Standard Access list R4(config)#ip pim accept-rp 180.40.7.129 1 R4(config)#^Z R4#config tsh run | b ip pim rp *Mar 1 07:16:27.090: %SYS-5-CONFIG_I: Configured from console by console R4#sh run | b ip pim rpip pim rp map  PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:56, expires: 00:02:04 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:56, expires: 00:02:02 R4#clea ip b m pim rp R4#clea ip mrout % Incomplete command. R4# RACK9AS>43 [Resuming connection 3 to r3 ... ] clea ip mroute *sh run int fa 0/1clea ip mroute *  R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#clea ip mrout * R4#clea ip mrout * pim rpsh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp mapclea ip mrout *  pim rpsh ip pim rp mapconfig t sh run | b ip pim rpip pim rp map clea ip mrou * p 224.7.7.7  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: . R4#p 224.7.7.7sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp mapp 224.7.7.7  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 136 ms R4# R4#\ % Unknown command or computer name, or unable to find computer address R4# R4#\p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 104 ms R4#p 224.7.7.7\ p 224.7.7.7sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:02, expires: 00:02:55 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:02, expires: 00:02:57 R4# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fga 0    a 0/1 R3(config-if)#ip pim de R3(config-if)#ip pim dense-mode ? proxy-register Send proxy registers R3(config-if)#ip pim dense-mode p R3(config-if)#ip pim dense-mode proxy-register ? list Access list route-map Route-map R3(config-if)#ip pim dense-mode proxy-register                                  exit R3(config)#do sh access-list ? LINE R3(config)#do sh access-list Standard IP access list 1 10 deny 224.20.68.1 (6 matches) 20 permit any (141 matches) R3(config)#co  int f a0/1 ^ % Invalid input detected at '^' marker. R3(config)#int f a0/1a0/1  R3(config-if)#ip pim de R3(config-if)#ip pim dense-mode p R3(config-if)#ip pim dense-mode proxy-register ? list Access list route-map Route-map R3(config-if)#ip pim dense-mode proxy-register ;i ? list Access list route-map Route-map R3(config-if)#ip pim dense-mode proxy-register ;i    li R3(config-if)#ip pim dense-mode proxy-register list ? <100-199> Extended access list number <2000-2699> Extended access list number (expanded range) WORD IP named extended access list R3(config-if)#ip pim dense-mode proxy-register list                                       access-list 100 per ip any any R3(config)#int fa0/1 R3(config-if)#ip pim den po ro R3(config-if)#ip pim den proxy-register li R3(config-if)#ip pim den proxy-register list 100 Warning: PIM register rate-limit set to 2 messages per second R3(config-if)#^Z R3#sh *Mar 1 07:19:54.466: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int fa 0/1 Building configuration... Current configuration : 142 bytes ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim dense-mode proxy-register list 100 duplex auto speed auto end R3# R3#sh run | i access-list 100 access-list 100 permit ip any any R3# R3#