=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.07.13 08:41:18 =~=~=~=~=~=~=~=~=~=~=~= S5# S5# S5# S5# RACK9AS>sh sess Conn Host Address Byte Idle Conn Name 1 r1 1.1.1.1 0 01:20 r1 2 r2 1.1.1.1 0 01:20 r2 3 r3 1.1.1.1 0 01:20 r3 4 r4 1.1.1.1 0 01:20 r4 * 5 r5 1.1.1.1 0 0 r5 6 r6 1.1.1.1 0 01:20 r6 7 r7 1.1.1.1 0 15 r7 RACK9AS>1 [Resuming connection 1 to r1 ... ] R1# R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4# RACK9AS>5 [Resuming connection 5 to r5 ... ] S5# RACK9AS>6 [Resuming connection 6 to r6 ... ] S6# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip dhcp pool Prob13 R2(dhcp-config)# host 180.40.7.97 255.255.255.224 R2(dhcp-config)# client-identifier 0063.6973.636f.2d30.3030.612e.6634.3961.$dentifier 0063.6973.636f.2d30.3030.612e.6634.3961.2 e33.3538.0063.6973.636f.2d30.3030.612e.6634.3961.2e33.3538.3 02d.4661.636f.2d30.3030.612e.6634.3961.2e33.3538.302d.4661.3 02f.32 R2(dhcp-config)#!  R2(dhcp-config)#int fa 0/2 ^ % Invalid input detected at '^' marker. R2(config)#int fa 0/2 2 ^ % Invalid input detected at '^' marker. R2(config)#int fa 0/2$636f.2d30.3030.612e.6634.3961.2e33.3538.302d.4661.302f.32 host 180.40.7.97 255.255.255.224 ip dhcp pool Prob13 nip dhcp pool Prob13oip dhcp pool Prob13 ip dhcp pool Prob13 R2(config)#no ip dhcp pool Prob13 6no ip dhcp pool Prob16  ip dhcp pool Prob16  R2(dhcp-config)# ip dhcp pool Prob16no ip dhcp pool Prob13int fa 0/2 $636f.2d30.3030.612e.6634.3961.2e33.3538.302d.4661.302f.32 R2(dhcp-config)#host 20.10.1.2 /24 R2(dhcp-config)#int fa 0/1 R2(config-if)#ip hel R2(config-if)#ip help R2(config-if)#ip helper-address 208.128   28.1.99 R2(config-if)#^Z R2# *Mar 2 21:41:28.862: %SYS-5-CONFIG_I: Configured from console by console R2# R2# R2# R2# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#on  int s 1/0.2 R7(config-subif)#ip helper-address 208.28.1.99 R7(config-subif)#do sh run int  s 1/0.2 Building configuration... Current configuration : 239 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 end R7(config-subif)#fram map ip 180.40.7.162 702br ^ % Invalid input detected at '^' marker. R7(config-subif)#fram map ip 180.40.7.162 702br br Only frame-relay interface-dlci command should beused on point-to-point interfaces not frame-relay map R7(config-subif)# frame-relay interface-dlci 702 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R7(config-subif)# frame-relay interface-dlci 702 pro R7(config-subif)# frame-relay interface-dlci 702 protocol ? A.B.C.D Protocol specific address ip IP R7(config-subif)# frame-relay interface-dlci 702 protocol 180.40.7.162 ? R7(config-subif)# frame-relay interface-dlci 702 protocol 180.40.7.162 %Can't add another VC to point-to-point subinterface R7(config-fr-dlci)#exit R7(config-subif)#no frame-relay interface-dlci 702 R7(config-subif)#no frame-relay interface-dlci 702 *Mar 2 21:48:56.688: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-subif)#no frame-relay interface-dlci 702exit no frame-relay interface-dlci 702exit  frame-relay interface-dlci 702 protocol 180.40.7.162 R7(config-fr-dlci)#exit R7(config-subif)# *Mar 2 21:49:10.514: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7(config-subif)#^Z R7# *Mar 2 21:49:25.411: %SYS-5-CONFIG_I: Configured from console by console R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/09 ^ % Invalid input detected at '^' marker. R3#sh run int s 1/09  Building configuration... Current configuration : 224 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast end R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh run | b dhcp ip dhcp pool Prob16 host 20.10.1.2 255.255.255.0 client-identifier 0063.6973.636f.2d30.3030.612e.6634.3961.2e33.3538.302d.4661.302f.32 ! ip cef no ip domain lookup ip audit po max-events 100 frame-relay de-list 1 protocol ip list 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! --More--  ! ! class-map match-all OSPF match access-group 100 ! ! policy-map Prob3b class OSPF set fr-de policy-map Prob3aOptionC class class-default shape average 64000 64000 32000 shape adaptive 32000 service-policy Prob3b ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown --More--   duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network broadcast ip ospf hello-interval 30 --More--   R2# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh ru n  n int s 1/0.2 Building configuration... Current configuration : 261 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 end R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#gl R7(config-if)#glbp ? <0-1023> Group number R7(config-if)#glbp 66 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 66 int fa 0/1glbp 66  6 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 666 ip ? A.B.C.D Virtual IP address R7(config-if)#glbp 666 ip 18040  .40.7.134 ? secondary Make this IP address a secondary address R7(config-if)#glbp 666 ip 180.40.7.134 R7(config-if)# R7(config-if)# R7(config-if)# R7(config-if)#do sh glbp FastEthernet0/1 - Group 666 State is Listen Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.552 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is unknown Standby is unknown Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There are no forwarders R7(config-if)# *Mar 2 22:03:07.258: %GLBP-6-STATECHANGE: FastEthernet0/1 Grp 666 state Standby -> Active R7(config-if)#do sh glbp FastEthernet0/1 - Group 666 State is Active 2 state changes, last state change 00:00:07 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.702 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is unknown Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There is 1 forwarder (0 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (default) Owner ID is 0012.7f80.f381 Redirection enabled Preemption enabled, min delay 30 sec Active is unknown R7(config-if)# *Mar 2 22:03:17.258: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 666 Fwd 1 state Listen -> Active R7(config-if)# R7(config-if)#do sh glbp FastEthernet0/1 - Group 666 State is Active 2 state changes, last state change 00:00:14 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.336 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is unknown Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There is 1 forwarder (1 active) Forwarder 1 State is Active 1 state change, last state change 00:00:04 MAC address is 0007.b402.9a01 (default) Owner ID is 0012.7f80.f381 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 R7(config-if)# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)# R3(config-if)# glbp 666 ip 180.40.7.134 R3(config-if)# *Mar 2 22:05:09.835: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 666 Fwd 2 state Listen -> Active R3(config-if)#do sh glbp FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:00:06 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.162 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 8.577 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14398.573 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.573 sec) Forwarder 2 State is Active --More--   1 state change, last state change 00:00:26 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec Active is local, weighting 100 R3(config-if)#gl R3(config-if)#glbp 666 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R3(config-if)#glbp 666 we R3(config-if)#glbp 666 weighting ? <1-254> Weighting maximum value track Interface tracking R3(config-if)#glbp 666 weighting tr R3(config-if)#glbp 666 weighting track ? <1-500> Tracked object R3(config-if)#glbp 666 weighting track                          do shr  ru n|}    n | i track track 3 ip route 20.10.2.0 255.255.255.0 reachability standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 standby 47 track 3 decrement 55 R3(config-if)#exit R3(config)#tra clk    ck 4 ip route 20.e10.110.1 10.1.0 255.255.255.0 re R3(config)#track 4 ip route 20.10.1.0 255.255.255.0 reachability R3(config-track)#int fa 0/1 R3(config-if)#gl R3(config-if)#glbp 666 w R3(config-if)#glbp 666 weighting t R3(config-if)#glbp 666 weighting track ? <1-500> Tracked object R3(config-if)#glbp 666 weighting track 4 ? decrement Weighting decrement R3(config-if)#glbp 666 weighting track 4 dec ? <1-255> Decrement value R3(config-if)#glbp 666 weighting track 4 dec 5f0    0 ? R3(config-if)#glbp 666 weighting track 4 dec 50 R3(config-if)#do sh glb FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:06:03 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.284 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 9.508 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14399.508 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.504 sec) Forwarder 2 State is Active --More--   R3(config-if)#do sh glb glbp 666 weighting track 4 dec 50                ? <1-254> Weighting maximum value track Interface tracking R3(config-if)#glbp 666 weighting 10  0 ? lower Weighting lower threshold upper Weighting upper threshold R3(config-if)#glbp 666 weighting 100 lo R3(config-if)#glbp 666 weighting 100 lower ? <1-99> Weighting lower threshold value R3(config-if)#glbp 666 weighting 100 lower 7 75 ? upper Weighting upper threshold R3(config-if)#glbp 666 weighting 100 lower 75 up ? <75-100> Weighting upper threshold value R3(config-if)#glbp 666 weighting 100 lower 75 up 100 R3(config-if)#glbp 666 weighting 100 lower 75 up 100 ? R3(config-if)#glbp 666 weighting 100 lower 75 up 100                                         RACK9AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#glbp 666 weighting 100 lower 75 up 100 R7(config-if)#glbp 666 weighting track 4 dec 50 R7(config-if)#do shr  run int fa 0/1 Building configuration... Current configuration : 354 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 ip helper-address 180.40.7.66 speed auto half-duplex vrrp 50 ip 180.40.7.133 vrrp 50 priority 150 glbp 666 ip 180.40.7.134 glbp 666 weighting 100 lower 75 glbp 666 weighting track 4 decrement 50 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 end R7(config-if)#track 4 ip route 20.10.1.0 255.255.255.0 reachability R7(config-track)#^Z R7# *Mar 2 22:15:24.911: %SYS-5-CONFIG_I: Configured from console by console R7#sh glb FastEthernet0/1 - Group 666 State is Active 2 state changes, last state change 00:12:28 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.042 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 9.667 sec) Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 4 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:12:18 MAC address is 0007.b402.9a01 (default) Owner ID is 0012.7f80.f381 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 --More--   Forwarder 2 State is Listen MAC address is 0007.b402.9a02 (learnt) Owner ID is 0012.7f8e.b6c0 Redirection enabled, 597.740 sec remaining (maximum 600 sec) Time to live: 14397.740 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 100 (expires in 7.740 sec) R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do shr  ru |   un | b ospf router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo-reply access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo-reply access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo-reply access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo ! route-map Prob1 permit 10 match ip address 102 match length 1001 2147483647 set interface Serial1/2 ! route-map Prob1 permit 20 match ip address 100 --More--   R3(config-if)#no router ospf 1 R3(config)# *Mar 2 22:17:24.688: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 22:17:24.688: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 22:17:24.688: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0 from 2WAY to DOWN, Neighbor Down: Interface down or detached *Mar 2 22:17:24.692: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on Serial1/0 from 2WAY to DOWN, Neighbor Down: Interface down or detached R3(config)# *Mar 2 22:17:24.692: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config)# *Mar 2 22:17:31.126: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Active -> Speak R3(config)# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh glb FastEthernet0/1 - Group 666 State is Active 2 state changes, last state change 00:14:31 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.790 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 9.475 sec) Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 4 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:14:21 MAC address is 0007.b402.9a01 (default) Owner ID is 0012.7f80.f381 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 --More--   Forwarder 2 State is Listen MAC address is 0007.b402.9a02 (learnt) Owner ID is 0012.7f8e.b6c0 Redirection enabled, 597.636 sec remaining (maximum 600 sec) Time to live: 14397.636 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 100 (expires in 7.632 sec) R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3(config)#do sh gl FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:12:40 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.419 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 8.734 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14398.730 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.730 sec) Forwarder 2 State is Active --More--   1 state change, last state change 00:12:48 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec Active is local, weighting 100 FastEthernet0/1 - Group 666 State is Disabled Virtual IP address is unknown Hello time 3 sec, hold time 10 sec Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is unknown Standby is unknown Priority 100 (default) Weighting 50, low (configured 100), thresholds: lower 75, upper 100 Track object 4 state Down decrement 50 Load balancing: round-robin There are no forwarders R3(config)#do sh gl FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:13:00 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.392 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 9.704 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14399.704 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.700 sec) Forwarder 2 State is Active --More--   1 state change, last state change 00:13:09 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec Active is local, weighting 100 FastEthernet0/1 - Group 666 State is Disabled Virtual IP address is unknown Hello time 3 sec, hold time 10 sec Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is unknown Standby is unknown Priority 100 (default) Weighting 50, low (configured 100), thresholds: lower 75, upper 100 Track object 4 state Down decrement 50 Load balancing: round-robin There are no forwarders R3(config)#do sh runb    Building configuration... Current configuration : 3708 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service tcp-small-servers ! hostname R3 ! boot-start-marker boot-end-marker ! logging buffered 4096 debugging ! no network-clock-participate slot 1 no network-clock-participate wic 0 no aaa new-model ip subnet-zero ! ! ip nbar port-map ftp tcp 21 20 --More--  ip dhcp excluded-address 180.40.7.129 ip dhcp excluded-address 180.40.7.131 180.40.7.134 ! ip dhcp pool Prob15 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 dns-server 208.28.1.82 domain-name MyCCIE option 150 ip 20.20.20.20 ! ip dhcp pool R4Pool host 180.40.7.130 255.255.255.224 client-identifier 0063.6973.636f.2d30.3033.302e.3835.6633.2e37.3034.302d.4661.302f.30 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! ! ! --More--  ! ! ! ! ! ! ! ! ! ! ! track 3 ip route 20.10.2.0 255.255.255.0 reachability ! track 4 ip route 20.10.1.0 255.255.255.0 reachability ! ! ! class-map match-all dscp26 match dscp af31 class-map match-all dscp24 match dscp cs3 class-map match-all af12 match dscp af12 --More--  class-map match-all dscp32 match dscp cs4 class-map match-all dscp28 match dscp af32 class-map match-all Telnet match protocol telnet class-map match-all prec3 match ip precedence 3 class-map match-all FTP match protocol ftp ! ! policy-map test class dscp24 class dscp26 class dscp28 class prec3 class dscp32 policy-map Prob7 class Telnet bandwidth percent 24 class FTP bandwidth percent 51 --More--   class class-default bandwidth percent 25 policy-map Prob11 class af12 priority percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 50 ip 180.40.7.133 glbp 666 ip 180.40.7.134 standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 --More--   standby 47 track 3 decrement 55 service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto glbp 666 weighting 100 lower 75 glbp 666 weighting track 4 decrement 50 ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 --More--   R3(config)#int fa0/0 R3(config-if)# glbp 666 weighting 100 lower 75 R3(config-if)# glbp 666 weighting track 4 decrement 50 R3(config-if)# glbp 666 weighting track 4 decrement 50100 lower 75 int fa0/0  1 R3(config-if)#no glbp 666 weighting 100 lower 75 R3(config-if)#no glbp 666 weighting track 4 decrement 50 R3(config-if)#do sh gl FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:14:07 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.315 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 8.357 sec) Standby is local Priority 100 (default) Weighting 50, low (configured 100), thresholds: lower 75, upper 100 Track object 4 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14398.353 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.353 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:14:16 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec Active is local, weighting 50 R3(config-if)# *Mar 2 22:19:35.622: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 666 Fwd 2 state Active -> Listen R3(config-if)#do sh gl FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:14:24 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.852 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 8.894 sec) Standby is local Priority 100 (default) Weighting 50, low (configured 100), thresholds: lower 75, upper 100 Track object 4 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14398.890 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.890 sec) Forwarder 2 --More--   State is Listen 2 state changes, last state change 00:00:07 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec Active is 180.40.7.131 (secondary), weighting 100 (expires in 7.660 sec) R3(config-if)# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#sh gl FastEthernet0/1 - Group 666 State is Active 2 state changes, last state change 00:16:36 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.148 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 8.101 sec) Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 4 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (2 active) Forwarder 1 State is Active 1 state change, last state change 00:16:26 MAC address is 0007.b402.9a01 (default) Owner ID is 0012.7f80.f381 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 --More--   Forwarder 2 State is Active 1 state change, last state change 00:00:15 MAC address is 0007.b402.9a02 (learnt) Owner ID is 0012.7f8e.b6c0 Redirection enabled, 584.955 sec remaining (maximum 600 sec) Time to live: 14384.951 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is local, weighting 100 R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#router ospf 1 R3(config-router)#net 0.0.00.  .0 255.255.255.255 % Incomplete command. R3(config-router)#net 0.0.0.0 255.255.255.255 area 0 R3(config-router)#^Z R3# *Mar 2 22:20:21.397: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 2 22:20:24.626: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3# *Mar 2 22:20:26.862: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from LOADING to FULL, Loading Done R3# *Mar 2 22:20:29.374: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R3#config tsh run int s 1/09en sh run int s 1/09 config t  sh gl FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:15:20 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.494 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 7.532 sec) Standby is local Priority 100 (default) Weighting 50, low (configured 100), thresholds: lower 75, upper 100 Track object 4 state Down decrement 50 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14397.528 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.524 sec) Forwarder 2 --More--   State is Listen 2 state changes, last state change 00:01:02 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec Active is 180.40.7.131 (secondary), weighting 100 (expires in 9.411 sec) R3# *Mar 2 22:20:46.186: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active R3#sh gl FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:15:33 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.135 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 9.171 sec) Standby is local Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 4 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14399.167 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.167 sec) Forwarder 2 --More--   State is Listen 2 state changes, last state change 00:01:15 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec (25 secs remaining) Active is 180.40.7.131 (secondary), weighting 100 (expires in 8.358 sec) R3#sh gl FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:15:46 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.163 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 8.193 sec) Standby is local Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 4 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14398.193 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.189 sec) Forwarder 2 --More--   State is Listen 2 state changes, last state change 00:01:29 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec (11 secs remaining) Active is 180.40.7.131 (secondary), weighting 100 (expires in 9.074 sec) R3#sh gl FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:15:50 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.502 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 7.536 sec) Standby is local Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 4 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14397.532 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.532 sec) Forwarder 2 --More--   State is Listen 2 state changes, last state change 00:01:32 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec (8 secs remaining) Active is 180.40.7.131 (secondary), weighting 100 (expires in 9.984 sec) R3# *Mar 2 22:21:16.696: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 666 Fwd 2 state Listen -> Active R3# sh glconfig tsh gl config tsh gl  FastEthernet0/0 - Group 666 State is Standby 1 state change, last state change 00:16:36 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.280 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 9.331 sec) Standby is local Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 4 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b402.9a01 (learnt) Owner ID is 0012.7f80.f381 Time to live: 14399.327 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.327 sec) Forwarder 2 --More--   State is Active 3 state changes, last state change 00:00:37 MAC address is 0007.b402.9a02 (default) Owner ID is 0012.7f8e.b6c0 Preemption enabled, min delay 30 sec Active is local, weighting 100 R3#sh run |     in t  t fa 0/0 Building configuration... Current configuration : 446 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 50 ip 180.40.7.133 glbp 666 ip 180.40.7.134 glbp 666 weighting 100 lower 75 glbp 666 weighting track 4 decrement 50 standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 standby 47 track 3 decrement 55 service-policy input test end R3# *Mar 2 22:22:21.170: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0 from LOADING to FULL, Loading Done *Mar 2 22:22:21.202: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on Serial1/0 from LOADING to FULL, Loading Done R3# R3#sh run | i track track 3 ip route 20.10.2.0 255.255.255.0 reachability track 4 ip route 20.10.1.0 255.255.255.0 reachability glbp 666 weighting track 4 decrement 50 standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 standby 47 track 3 decrement 55 R3# R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh run |   int fa 0/1 Building configuration... Current configuration : 354 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 ip helper-address 180.40.7.66 speed auto half-duplex vrrp 50 ip 180.40.7.133 vrrp 50 priority 150 glbp 666 ip 180.40.7.134 glbp 666 weighting 100 lower 75 glbp 666 weighting track 4 decrement 50 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 end R7# R7#sh run | i track track 4 ip route 20.10.1.0 255.255.255.0 reachability glbp 666 weighting track 4 decrement 50 R7# R7# RACK9AS>6 [Resuming connection 6 to r6 ... ] S6#confg ig t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#do sh ml qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   S6(config)#coni    int gi 0/1 S6(config-if)#wrr S6(config-if)#wrr-queue ? bandwidth Configure WRR bandwidth cos-map Configure cos-map for a queue id dscp-map Configure dscp-map for a queue threshold queue-limit Configure queue-limit random-detect Configure random-detect threshold Configure queue tail-drop thresholds S6(config-if)#wrr-queue co S6(config-if)#wrr-queue cos-map ? <1-4> enter cos-map queue id S6(config-if)#wrr-queue cos-map ? <1-4> enter cos-map queue id S6(config-if)#wrr-queue cos-map 2 0 ? <0-7> CoS values separated by spaces (up to 8 values total) S6(config-if)#wrr-queue cos-map 2 0 45  5 6 7 S6(config-if)#wrr-queue cos-map 2 0 4 5 6 7           3 3 S6(config-if)#do shr  ml  s qos         int gi 0/1 GigabitEthernet0/1 is down, line protocol is down (notconnect) Hardware is Gigabit Ethernet, address is 000a.f49a.3599 (bia 000a.f49a.3599) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Auto-duplex, Auto-speed, link type is auto, media type is unknown input flow-control is off, output flow-control is off ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts (0 multicast) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 0 packets output, 0 bytes, 0 underruns --More--   S6(config-if)#do sh int gi 0/1Rint gi 0/1Uint gi 0/1Nint gi 0/1 int gi 0/1 Building configuration... Current configuration : 150 bytes ! interface GigabitEthernet0/1 switchport mode dynamic desirable wrr-queue cos-map 1 1 wrr-queue cos-map 2 0 2 4 5 6 7 wrr-queue cos-map 3 3 end S6(config-if)#pr S6(config-if)#priority-queue ou S6(config-if)#wrr S6(config-if)#wrr-queue b S6(config-if)#wrr-queue bandwidth ? <1-65536> enter bandwidth weight for qid 1 S6(config-if)#wrr-queue bandwidth 25 50 25 1 S6(config-if)#wrr th S6(config-if)#wrr threshold ? <1-4> enter threshold queue id (1-4) S6(config-if)#wrr threshold 1           dsc S6(config-if)#wrr dscp-map ? <1-2> enter dscp-map threshold id (1-2) S6(config-if)#wrr dscp-map 2 ? <0-63> DSCP values separated by spaces (up to 8 values total) S6(config-if)#wrr dscp-map 2 10 26 S6(config-if)#wrr th S6(config-if)#wrr threshold ? <1-4> enter threshold queue id (1-4) S6(config-if)#wrr threshold 1`    100     40 100 S6(config-if)#\]  wrr threshold 1 40 100 wrr threshold 1 40 100 100  100 100  100 3 1006 1000 100 100100  100  100  100 3 100 1006 1000 100 S6(config-if)#^Z S6# 1d22h: %SYS-5-CONFIG_I: Configured from console by console S6#sh run ion  nt gi 0/1 Building configuration... Current configuration : 290 bytes ! interface GigabitEthernet0/1 switchport mode dynamic desirable wrr-queue bandwidth 25 50 25 1 wrr-queue threshold 1 40 100 wrr-queue threshold 3 60 100 wrr-queue cos-map 1 1 wrr-queue cos-map 2 0 2 4 5 6 7 wrr-queue cos-map 3 3 wrr-queue dscp-map 2 10 26 priority-queue out end S6# S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int gi 0/2 S6(config-if)# wrr-queue cos-map 1 1 S6(config-if)# wrr-queue cos-map 2 0 2 4 5 6 7 S6(config-if)# wrr-queue cos-map 3 3 S6(config-if)# wrr-queue dscp-map 2 28 30 S6(config-if)#iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii]                                   wrr-queue bandwidth 25 50 25 1 S6(config-if)#wrr S6(config-if)#wrr-queue r S6(config-if)#wrr-queue random-detect ? max-threshold max-thresholds S6(config-if)#wrr-queue random-detect m S6(config-if)#wrr-queue random-detect max-threshold ? <1-4> enter threshold queue id (1-4) S6(config-if)#wrr-queue random-detect max-threshold 3 ? <1-100> enter percent of queue size for threshold 1 S6(config-if)#wrr-queue random-detect max-threshold 3 100 ? <1-100> enter percent of queue size for threshold 2 S6(config-if)#wrr-queue random-detect max-threshold 3 100 40 ? S6(config-if)#wrr-queue random-detect max-threshold 3 100 40   S6(config-if)#^Z S6# 1d22h: %SYS-5-CONFIG_I: Configured from console by console S6#s run int gi / 0/2 Building configuration... Current configuration : 258 bytes ! interface GigabitEthernet0/2 switchport mode dynamic desirable wrr-queue bandwidth 25 50 25 1 wrr-queue random-detect max-threshold 3 100 40 wrr-queue cos-map 1 1 wrr-queue cos-map 2 0 2 4 5 6 7 wrr-queue cos-map 3 3 wrr-queue dscp-map 2 28 30 end S6# S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int gi 0/2 S6(config-if)#int gi 0/2wrr-queue random-detect max-threshold 3 100 40  ? <1-100> enter percent of queue size for threshold 2 S6(config-if)#wrr-queue random-detect max-threshold 3 100                                             ^Z S6# 1d23h: %SYS-5-CONFIG_I: Configured from console by console S6# S6# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#cof   sh run |   b class class-map match-any JPEG match protocol http mime "*jpeg" match protocol http url "*.jpeg" match protocol http url "*.jpg" match protocol http url "*.jpe" class-map match-all S5Other match access-group 1 class-map match-all S5Telnet match protocol telnet match access-group 1 ! ! policy-map Prob5 class S5Telnet bandwidth 1000 class JPEG shape average 1000000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! ! ! --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#class R7(config)#class-map ftp R7(config-cmap)#matfh    c pro R7(config-cmap)#matc protocol ftp R7(config-cmap)#exit R7(config)#cla R7(config)#class-map telnet R7(config-cmap)#match pro R7(config-cmap)#match protocol telnet R7(config-cmap)#exit R7(config)#nbar      do sh run | i nbar R7(config)#nbp ar ? % Unrecognized command R7(config)#nbar      ip n R7(config)#ip nb R7(config)#ip nbar p R7(config)#ip nbar por R7(config)#ip nbar port-map ftp tcp 20 21 R7(config)#pol R7(config)#policy-map Optional R7(config-pmap)#class R7(config-pmap)#class ftp R7(config-pmap-c)#ban R7(config-pmap-c)#bandwidth pe R7(config-pmap-c)#bandwidth percent 25 R7(config-pmap-c)#l class telnet R7(config-pmap-c)#class telnetbandwidth percent 25 R7(config-pmap-c)#int fa0/1 R7(config-if)#serv R7(config-if)#service-policy out Optional Policy map Prob5 is already attached R7(config-if)#service-policy out Optionalint fa0/1  0 R7(config-if)#int fa0/0service-policy out Optional R7(config-if)#^Z R7#sh run | *Mar 2 23:03:57.770: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b class class-map match-all telnet match protocol telnet class-map match-any JPEG match protocol http mime "*jpeg" match protocol http url "*.jpeg" match protocol http url "*.jpg" match protocol http url "*.jpe" class-map match-all S5Other match access-group 1 class-map match-all S5Telnet match protocol telnet match access-group 1 class-map match-all ftp match protocol ftp ! ! policy-map Prob5 class S5Telnet bandwidth 1000 class JPEG shape average 1000000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 --More--  policy-map Optional class ftp bandwidth percent 25 class telnet bandwidth percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex service-policy output Optional ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 --More--   R7#sah h run | b class     nbar ip nbar port-map ftp tcp 20 21 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! track 4 ip route 20.10.1.0 255.255.255.0 reachability ! ! ! --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#access-list             do sh access-list 100 tcp any any eq ? LINE R7(config)#do sh access-list 100 tcp any any eq do sh access-list 100 tcp any any eq  sh access-list 100 tcp any any eq  sh access-list 100 tcp any any eq access-list 100 tcp any any eq access-list 100 tcp any any eq access-list 100 tcp any any eq access-list 100 tcp any any eq ? % Unrecognized command R7(config)#access-list 100 tcp any any eq ptcp any any eq etcp any any eq rtcp any any eq  tcp any any eq tcp any any eq ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   pop2 Post Office Protocol v2 (109) pop3 Post Office Protocol v3 (110) smtp Simple Mail Transport Protocol (25) sunrpc Sun Remote Procedure Call (111) syslog Syslog (514) tacacs TAC Access Control System (49) talk Talk (517) telnet Telnet (23) time Time (37) uucp Unix-to-Unix Copy Program (540) whois Nicname (43) www World Wide Web (HTTP, 80) R7(config)#access-list 100 per tcp any any eq                       00               do sh acess-li    s csessss-li Standard IP access list 1 10 permit 208.28.1.2 (1140077 matches) R7(config)#access-list 100 per ip any host 87.23.11.123 R7(config)#access-list 100 per ip any host 87.23.11.123 anyhost 87.23.11.123 any host 87.23.11.123 any host 87.23.11.123 any host 87.23.11.123 any  R7(config)#class R7(config)#class-map sql R7(config-cmap)#match acc R7(config-cmap)#match access-group 100 R7(config-cmap)#match pr R7(config-cmap)#match prp R7(config-cmap)#match prp o R7(config-cmap)#match protocol s R7(config-cmap)#match protocol sq R7(config-cmap)#match protocol sql? sqlnet sqlserver R7(config-cmap)#match protocol sqls R7(config-cmap)#match protocol sqlserver R7(config-cmap)#pol R7(config-cmap)#pol   exit R7(config)#pol exitmatch protocol sqlserver access-group 100 class-map sql access-list 100 per ip host 87.23.11.123 anyany host 87.23.11.123do sh access-li service-policy out Optional Optional  Optional  Optional Optional - Optionalm Optionala Optionalp Optionale-policy-map Optional policy-map Optional policy-map Optional policy-map Optional policy-map Optional policy-map Optional policy-map Optional policy-map Optional  R7(config-pmap)#class sql R7(config-pmap-c)#pri R7(config-pmap-c)#priority 56  ? <8-2000000> Kilo Bits per second percent % of total bandwidth R7(config-pmap-c)#priority 56 ? <32-2000000> Burst in bytes R7(config-pmap-c)#priority 56 128 R7(config-pmap-c)#^Z R7# *Mar 2 23:12:34.181: %SYS-5-CONFIG_I: Configured from console by console R7#shrun | run |run | b class class-map match-all telnet match protocol telnet class-map match-any JPEG match protocol http mime "*jpeg" match protocol http url "*.jpeg" match protocol http url "*.jpg" match protocol http url "*.jpe" class-map match-all S5Other match access-group 1 class-map match-all S5Telnet match protocol telnet match access-group 1 class-map match-all ftp match protocol ftp class-map match-all sql match access-group 100 match protocol sqlserver ! ! policy-map Prob5 class S5Telnet bandwidth 1000 class JPEG --More--   shape average 1000000 --More--   class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 policy-map Optional class ftp bandwidth percent 25 class telnet bandwidth percent 25 class sql priority 56 128 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex service-policy output Optional ! interface BRI0/0 --More--   R7#sh run | i access-list access-list 1 permit 208.28.1.2 access-list 100 permit ip any host 87.23.11.123 access-list 100 permit ip host 87.23.11.123 any R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#priority 56 128class sql policy-map Optional R7(config-pmap)#class class-defau;lt   lt R7(config-pmap-c)#fai R7(config-pmap-c)#fair-queue R7(config-pmap-c)#do sh pol int fa0/0 FastEthernet0/0 Service-policy output: Optional Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: sql (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 100 Match: protocol sqlserver Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 149 packets, 14872 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 256 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-pmap-c)# do sh pol int fa0/0fair-queue ? <16-4096> Number Dynamic Conversation Queues R7(config-pmap-c)#fair-queue 512 R7(config-pmap-c)#fair-queue 512do sh pol int fa0/0 FastEthernet0/0 Service-policy output: Optional Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 521 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 522 Bandwidth 25 (%) Bandwidth 25000 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: sql (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 100 Match: protocol sqlserver Queueing Strict Priority Output Queue: Conversation 520 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 153 packets, 15180 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 512 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-pmap-c)# ^Z R7# *Mar 2 23:15:29.696: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b pol policy-map Prob5 class S5Telnet bandwidth 1000 class JPEG shape average 1000000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 policy-map Optional class ftp bandwidth percent 25 class telnet bandwidth percent 25 class sql priority 56 128 class class-default fair-queue 512 ! ! ! ! ! ! --More--   R7#configt  t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pol R7(config)#policy-map Prob2324 R7(config-pmap)#class R7(config-pmap)#class ftp R7(config-pmap-c)#shap R7(config-pmap-c)#shape av R7(config-pmap-c)#shape average 256   ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R7(config-pmap-c)#shape average 256000 ? <256-154400000> bits per interval, sustained. Needs to be multiple of 128. Recommend not to configure it, the algorithm will find out the best value R7(config-pmap-c)#shape average 256000 R7(config-pmap-c)#exit R7(config-pmap)#class telnet R7(config-pmap-c)#pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 56000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 1400 ? <1000-512000000> Burst bytes be Excess burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 1400 3500 ? conform-action action when rate is less than conform burst R7(config-pmap-c)#police 56000 1400 3500 con R7(config-pmap-c)#police 56000 1400 3500 conform-action se R7(config-pmap-c)#police 56000 1400 3500 conform-action set-p R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit ? <0-7> new precedence R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1                                                           ewxit ^ % Invalid input detected at '^' marker. R7(config-pmap-c)#exit R7(config-pmap)#exit R7(config)#class tesst    t ^ % Invalid input detected at '^' marker. R7(config)#class test - test m test a test p test  R7(config-cmap)#math ip     tch ip ? dscp Match IP DSCP (DiffServ CodePoints) precedence Match IP precedence rtp Match RTP port nos R7(config-cmap)#match ip pr R7(config-cmap)#match ip precedence ? <0-7> Enter up to 4 precedence values separated by white-spaces critical Match packets with critical precedence (5) flash Match packets with flash precedence (3) flash-override Match packets with flash override precedence (4) immediate Match packets with immediate precedence (2) internet Match packets with internetwork control precedence (6) network Match packets with network control precedence (7) priority Match packets with priority precedence (1) routine Match packets with routine precedence (0) R7(config-cmap)#match ip precedence                     exit R7(config)#no clas R7(config)#no class-map tst  est R7(config)#no class-map testexit class-map test  test exit wxitclass telnetexit shape average 256000 class ftp policy-map Prob2324 R7(config-pmap)#policy-map Prob2324no class-map test exit class-map test  test exit wxitclass telnet R7(config-pmap-c)#pol R7(config-pmap-c)#police 56000 1400 25  3500 class telnet con R7(config-pmap-c)#class telnetcon               class telnetpolicy-map Prob2324no class-map test exit class-map test exit no class-map testpolicy-map Prob2324class telnet  class telnet R7(config-pmap-c)#pol R7(config-pmap-c)#police 56000 1400 3500 con R7(config-pmap-c)#police 56000 1400 3500 conform-action se R7(config-pmap-c)#police 56000 1400 3500 conform-action set-p R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 e R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action s R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action set-p R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 v R7(config-pmap-c)#$smit 1 exceed-action set-prec-transmit 0 violate-action dr R7(config-pmap-c)#$eed-action set-prec-transmit 0 violate-action drop R7(config-pmap-c-police)#exit R7(config-pmap-c)#exit R7(config-pmap)#class class-defaultr  t R7(config-pmap-c)#fa R7(config-pmap-c)#fair-queue R7(config-pmap-c)#qu R7(config-pmap-c)#queue-limit 100 R7(config-pmap-c)#int s 1/.0  0.1 R7(config-subif)#ser R7(config-subif)#service-policy out Prob2324 CBWFQ : Not supported on subinterfaces R7(config-subif)#exit R7(config)#map R7(config)#map-cl R7(config)#map-class fra R7(config)#map-class frame-relay Prob2324 R7(config-map-class)#ser R7(config-map-class)#service-policy map-class frame-relay Prob2324exit service-policy out Prob2324 R7(config-map-class)#int s 1/0.1 R7(config-subif)#fra class Prob2324 R7(config-subif)#int s 1/0 R7(config-if)#fram traff Only class-default supported over FR VCs Traffic shaping not enabled due to invalid policy in map-class Prob2324 R7(config-if)#exit R7(config)#exitfram traffint s 1/0 fra class Prob2324int s 1/0.1 service-policy out Prob2324map-class frame-relay Prob2324nexit service-policy out Prob2324int s 1/0.1 queue-limit 100fair-queue class class-defaultexit $smit 1 exceed-action set-prec-transmit 0 violate-action drop class telnet policy-map Prob2324 R7(config-pmap)#class ftp R7(config-pmap-c)#no shape av 256000 R7(config-pmap-c)#pol R7(config-pmap-c)#police 256000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 256000 R7(config-pmap-c-police)#int s 1/0 R7(config-if)#fram traff R7(config-if)#do sh pol int s 1/0.1 Serial1/0.1: DLCI 703 - Service-policy output: Prob2324 Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp police: cir 256000 bps, bc 8000 bytes conformed 0 packets, 0 bytes; actions: transmit exceeded 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet police: cir 56000 bps, bc 1400 bytes, be 3500 bytes conformed 0 packets, 0 bytes; actions: --More--   R7(config-if)#do sh pol int s 1/0.1           Prob2324 Policy Map Prob2324 Class ftp police cir 256000 bc 8000 conform-action transmit exceed-action drop Class telnet police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop Class class-default Flow based Fair Queueing Bandwidth 0 (kbps) Max Threshold 100 (packets) R7(config-if)# do sh pol Prob2324int s 1/0.1 Serial1/0.1: DLCI 703 - Service-policy output: Prob2324 Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp police: cir 256000 bps, bc 8000 bytes conformed 0 packets, 0 bytes; actions: transmit exceeded 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet police: cir 56000 bps, bc 1400 bytes, be 3500 bytes conformed 0 packets, 0 bytes; actions: --More--   set-prec-transmit 1 exceeded 0 packets, 0 bytes; actions: set-prec-transmit 0 violated 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps, violate 0 bps Class-map: class-default (match-any) 3 packets, 588 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 16 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-if)#  ^Z R7#sh run | *Mar 2 23:27:39.112: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b class class-map match-all telnet match protocol telnet class-map match-any JPEG match protocol http mime "*jpeg" match protocol http url "*.jpeg" match protocol http url "*.jpg" match protocol http url "*.jpe" class-map match-all S5Other match access-group 1 class-map match-all S5Telnet match protocol telnet match access-group 1 class-map match-all ftp match protocol ftp class-map match-all sql match access-group 100 match protocol sqlserver ! ! policy-map Prob5 class S5Telnet bandwidth 1000 class JPEG --More--   shape average 1000000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 policy-map Prob2324 class ftp police 256000 class telnet police 56000 1400 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop class class-default fair-queue queue-limit 100 policy-map Optional class ftp bandwidth percent 25 class telnet bandwidth percent 25 class sql priority 56 128 class class-default fair-queue 512 ! --More--  ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex service-policy output Optional ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 ip helper-address 180.40.7.66 speed auto half-duplex vrrp 50 ip 180.40.7.133 vrrp 50 priority 150 glbp 666 ip 180.40.7.134 --More--   glbp 666 weighting 100 lower 75 glbp 666 weighting track 4 decrement 50 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf hello-interval 30 ip ospf priority 0 frame-relay class Prob2324 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 --More--   ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address --More--   shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! ! map-class frame-relay Prob6 frame-relay priority-group 1 ! --More--  map-class frame-relay Prob2324 --More--   service-policy output Prob2324 --More--  access-list 1 permit 208.28.1.2 --More--  access-list 100 permit ip any host 87.23.11.123 --More--  access-list 100 permit ip host 87.23.11.123 any --More--  priority-list 1 protocol ip high tcp telnet --More--  priority-list 1 protocol ip low tcp www --More--  priority-list 1 default medium --More--  ! --More--  ! --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#P pol R7(config)#policy-map Prob2324 R7(config-pmap)#class R7(config-pmap)#class class-defai  R7(config-pmap)#class class-default R7(config-pmap-c)#po R7(config-pmap-c)#police l ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 512000 R7(config-pmap-c-police)#exit R7(config-pmap-c)#exit R7(config-pmap)#exit R7(config)#exitpolice 512000class class-default policy-map Prob2324 do sh pol int s 1/0.1Prob2324 int s 1/0.1Prob2324 int s 1/0.1fram traff int s 1/0 police 256000 no shape av 256000class ftp policy-map Prob2324exit fram traffexit policy-map Prob2324class ftp no shape av 256000police 256000 int s 1/0 fram traffdo sh pol int s 1/0.1Prob2324 int s 1/0.1policy-map Prob2324 class class-default police 512000 exit  map   R7(config)#map-c R7(config)#map-class fram R7(config)#map-class frame-relay Prob2324 R7(config-map-class)#fram cir ? <1-45000000> Applied to both Incoming/Outgoing CIR, Bits per second in Incoming CIR out Outgoing CIR R7(config-map-class)#fram cir 6000 000 R7(config-map-class)#^Z R7# *Mar 2 23:33:28.180: %SYS-5-CONFIG_I: Configured from console by console R7#sh run   n | b class-defaulrt  t class class-default fair-queue queue-limit 100 police 512000 policy-map Optional class ftp bandwidth percent 25 class telnet bandwidth percent 25 class sql priority 56 128 class class-default fair-queue 512 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex --More--   R7#sh run | b map-class map-class frame-relay Prob6 frame-relay priority-group 1 ! map-class frame-relay Prob2324 frame-relay cir 600000 service-policy output Prob2324 access-list 1 permit 208.28.1.2 access-list 100 permit ip any host 87.23.11.123 access-list 100 permit ip host 87.23.11.123 any priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www priority-list 1 default medium ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 --More--   R7# RACK9AS> [Resuming connection 7 to r7 ... ] R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#configt Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class-map match-all telnet R3(config-cmap)# match protocol telnet R3(config-cmap)#class-map match-all ftp R3(config-cmap)# match protocol ftp R3(config-cmap)#! exit R3(config)#pol R3(config)#policy-map Prob24test     R3(config-pmap)#exit R3(config)#exitpolicy-map Prob24a R3(config-pmap)#class R3(config-pmap)#class ftp R3(config-pmap-c)#shave  pe av R3(config-pmap-c)#shape average 256 ^ % Invalid input detected at '^' marker. R3(config-pmap-c)#shape average 2566     ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R3(config-pmap-c)#shape average 256000 R3(config-pmap-c)#exit R3(config-pmap)#class telnet R3(config-pmap-c)#class telnetexit shape average 25600056000  R3(config-pmap-c)#eixt ^ % Invalid input detected at '^' marker. R3(config-pmap-c)#ei xit R3(config-pmap)#class cl; ass-default R3(config-pmap-c)#shap R3(config-pmap-c)#shape av R3(config-pmap-c)#shape average 512000 R3(config-pmap-c)#exi R3(config-pmap)#exiyt ^ % Invalid input detected at '^' marker. R3(config-pmap)#exiyt  t R3(config)#e % Ambiguous command: "e" R3(config)#it  exityt shape average 512000class class-default exit ixtshape average 56000class telnet exit shape average 256000 class ftp policy-map Prob24a  R3(config-pmap)#class class-default R3(config-pmap-c)#serv R3(config-pmap-c)#service-policy Prob24a R3(config-pmap-c)#shap R3(config-pmap-c)#shape av R3(config-pmap-c)#shape average 600000 R3(config-pmap-c)#int s v1/0 ^ % Invalid input detected at '^' marker. R3(config)#int s v1/01/0  R3(config-if)#serv R3(config-if)#service-policy out   Prob24 GTS : Can be enabled only at the first level R3(config-if)#service-policy out Prob24int s 1/0 v1/0shape average 600000ervice-policy Prob24a class class-default policy-map Prob24  R3(config-pmap)#policy-map Prob24service-policy out Prob24int s 1/0 v1/0shape average 600000ervice-policy Prob24aclass class-default  R3(config-pmap-c)#no shap R3(config-pmap-c)#no shape aver 600000 R3(config-pmap-c)#pol R3(config-pmap-c)#police 00   6    6000 000 R3(config-pmap-c-police)#int0 s 1/0 s 1/0  R3(config-if)#int s 1/0police 600000no shape aver 600000class class-default policy-map Prob24 service-policy out Prob24 GTS : Can be enabled only at the first level R3(config-if)#exit R3(config)#no    do sh       no pol R3(config)#no policy-map Prob24 R3(config)#no policy-map Prob24a R3(config)#do sh       no cl R3(config)#no cla R3(config)#no class-map ftp R3(config)#no class-map ftp   telnet R3(config)#^Z R3# *Mar 2 23:40:27.800: %SYS-5-CONFIG_I: Configured from console by console R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run | b       int s 1/0.2 Building configuration... Current configuration : 206 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob3OptionB end R2#sh run | b map-class map-class frame-relay Prob3OptionB frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn access-list 100 deny ospf any any access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login --More--   R2# config t Enter configuration commands, one per line. End wit