=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.04.12 09:45:36 =~=~=~=~=~=~=~=~=~=~=~= x  S6# S6# S6#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Default DSCP Mutation Map: --More--   S6#confifg t ^ % Invalid input detected at '^' marker. S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#mls qos map ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S6(config)#mls qos map ip S6(config)#mls qos map ip-prec-dscp ? <0-63> 8 dscp values separated by spaces S6(config)#mls qos map ip-prec-dscp 0 14 16 28 32 40 48 56 S6(config)#mls qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S6(config)#int fa 0/7 S6(config-if)#mls S6(config-if)#mls tr  qos tru S6(config-if)#mls qos trust ip S6(config-if)#mls qos trust ip-precedence S6(config-if)#^Z S6# 22:52:39: %SYS-5-CONFIG_I: Configured from console by console S6# RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#ping 180.40.7.13029 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 ping 180.40.7.129 rep 1000 Type escape sequence to abort. Sending 1000, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 1015 packets, 115710 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   Class-map: class-default (match-any) 12654 packets, 1237484 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#qsh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 1015 packets, 115710 bytes 5 minute offered rate 4000 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   Class-map: class-default (match-any) 12656 packets, 1237680 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 1015 packets, 115710 bytes 5 minute offered rate 2000 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   Class-map: class-default (match-any) 12657 packets, 1237778 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 1015 packets, 115710 bytes 5 minute offered rate 2000 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   Class-map: class-default (match-any) 12658 packets, 1237876 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6#sh     RACK14AS>z5 Translating "z5" Translating "z5" % Unknown command or computer name, or unable to find computer address RACK14AS>5 [Resuming connection 5 to r5 ... ] !!!!!!!!!!!!!!! !!!!!! S5#ping 180.40.7.129 rep 1000 Type escape sequence to abort. Sending 1000, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!! Success rate is 100 percent (1000/1000), round-trip min/avg/max = 1/2/4 ms S5# RACK14AS>3 [Resuming connection 3 to r3 ... ] sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 2015 packets, 229710 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   Class-map: class-default (match-any) 12667 packets, 1238758 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6#sh run I   | b mls qos mls qos map ip-prec-dscp 0 14 16 28 32 40 48 56 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 no switchport ip address 20.10.2.1 255.255.255.0 ! interface FastEthernet0/2 --More--   no switchport ip address 20.10.1.2 255.255.255.0 ! interface FastEthernet0/3 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport access vlan 10 switchport mode dynamic desirable ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 switchport access vlan 10 switchport mode dynamic desirable mls qos trust ip-precedence ! interface FastEthernet0/8 switchport mode dynamic desirable --More--   S6# RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ml  s qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S5(config)#int fa 0/24 S5(config-if)#mls qos tru S5(config-if)#mls qos trust dsc S5(config-if)#mls qos trust dscp S5(config-if)#exit S5(config)#mls qos ? aggregate-policer Assign aggregate policer cos Configure CoS setting map Define QoS mapping min-reserve Configure min-reserve buffers S5(config)#mls qos map ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S5(config)#mls qos map dsc S5(config)#mls qos map dscp-m S5(config)#mls qos map dscp-mutation ? WORD DSCP mutation map name S5(config)#mls qos map dscp-mutation Prob9 ? <0-63> DSCP values separated by spaces (up to 8 values total) S5(config)#mls qos map dscp-mutation Prob9 28 ? <0-63> DSCP values separated by spaces (up to 8 values total) to Specify egress DSCPs S5(config)#mls qos map dscp-mutation Prob9 28 to 26 S5(config)#mls qos map dscp-mutation Prob9 28 to 26        14 to 12 S5(config)#int fa 0/24 S5(config-if)#mls qos ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S5(config-if)#mls qos dsc S5(config-if)#mls qos dscp-mutation ? WORD dscp-mutation name S5(config-if)#mls qos dscp-mutation Prob9 ? S5(config-if)#mls qos dscp-mutation Prob9 S5(config-if)#^Z S5#config t~ 23:00:25: %SYS-5-CONFIG_I: Configured from console by console S5#config t~ping 180.40.7.129 rep 100000 Type escape sequence to abort. Sending 100000, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!! RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 1502 packets, 171228 bytes 5 minute offered rate 6000 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 2015 packets, 229710 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   Class-map: class-default (match-any) 12745 packets, 1246362 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#qsh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 4421 packets, 503994 bytes 5 minute offered rate 6000 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 2015 packets, 229710 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   Class-map: class-default (match-any) 12747 packets, 1246558 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 5791 packets, 660174 bytes 5 minute offered rate 20000 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 2015 packets, 229710 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   Class-map: class-default (match-any) 12747 packets, 1246558 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 13223 packets, 1507422 bytes 5 minute offered rate 36000 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 2015 packets, 229710 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   R3# RACK14AS>5 [Resuming connection 5 to r5 ... ] !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!. Success rate is 99 percent (21390/21391), round-trip min/avg/max = 1/2/56 ms S5#sh run | b mls qos mls qos map dscp-mutation Prob9 14 to 12 mls qos map dscp-mutation Prob9 28 to 26 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport mode dynamic desirable ! interface FastEthernet0/2 --More--   switchport mode dynamic desirable ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport mode dynamic desirable ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 no switchport ip address 208.28.1.2 255.255.255.0 ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 --More--   switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/14 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/15 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! --More--  interface FastEthernet0/16 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/17 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/18 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/19 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/20 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/21 switchport mode dynamic desirable mls qos dscp-mutation Prob9 --More--  ! interface FastEthernet0/22 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/23 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk mls qos trust dscp mls qos dscp-mutation Prob9 ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address --More--   S5# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 21391 packets, 2438574 bytes 5 minute offered rate 46000 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 2015 packets, 229710 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 --More--   Class-map: class-default (match-any) 12773 packets, 1249066 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7#sh     RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class dscp26 ^ % Invalid input detected at '^' marker. R3(config)#class dscp26- dscp26m dscp26a dscp26p dscp26 R3(config-cmap)#class-map dscp26 match ip a dsc R3(config-cmap)#match ip dscp 28 R3(config-cmap)#exit R3(config)#exitmatch ip dscp 28class-map dscp26mdscp26adscp26tdscp26cdscp26hdscp26-dscp26adscp26ndscp26ydscp26 dscp26 R3(config-cmap)#^Z R3# *Mar 1 23:03:02.165: %SYS-5-CONFIG_I: Configured from console by console R3# RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | b mls qosping 180.40.7.129 rep 100000 Type escape sequence to abort. Sending 100000, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config tsh pol int fa 0/0^x6 sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 21391 packets, 2438574 bytes 5 minute offered rate 2000 bps Match: dscp af31 (26) Match: ip dscp af32 (28) Class-map: dscp28 (match-all) 2015 packets, 229710 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 1425 packets, 162450 bytes 5 minute offered rate 0 bps --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class-map match-any dscp26 dscp26  dscp26 l dscp26l dscp26 R3(config-cmap)#no class-map match-all dscp26ny dscp26exit match ip dscp 28nmatch ip dscp 28omatch ip dscp 28 match ip dscp 28 R3(config-cmap)#^Z R3# *Mar 1 23:03:41.253: %SYS-5-CONFIG_I: Configured from console by console R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#do sh run | b poli policy-map Prob5 class S5Telnet bandwidth 1000 class JPG shape average 1000000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! --More--   R7(config)#policy-map Prob5 R7(config-pmap)# class S5Other R7(config-pmap-c)#pol R7(config-pmap-c)#police 500  000 con R7(config-pmap-c)#police 500000 conform-action set R7(config-pmap-c)#police 500000 conform-action set-1 p R7(config-pmap-c)#police 500000 conform-action set-prec-transmit 1 R7(config-pmap-c-police)# RACK14AS>5 [Resuming connection 5 to r5 ... ] !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class   R3(config)#class-map dscp14 R3(config-cmap)#match ip dscp 14 R3(config-cmap)#exit R3(config)#exitmatch ip dscp 14 2 ^ % Invalid input detected at '^' marker. R3(config)#match ip dscp 12exit match ip dscp 14class-map dscp14 2 R3(config-cmap)#class-map dscp12match ip dscp 12 R3(config-cmap)#exit R3(config)#pol R3(config)#policy-map test R3(config-pmap)#class R3(config-pmap)#class dscp14 R3(config-pmap-c)#exit R3(config-pmap)#exitclass dscp14 2 R3(config-pmap-c)#^Z R3#config tsh pol int fa 0/0 *Mar 1 23:05:23.762: %SYS-5-CONFIG_I: Configured from console by console R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp24 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp cs3 (24) Class-map: dscp26 (match-all) 45502 packets, 5187228 bytes 5 minute offered rate 59000 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 2015 packets, 229710 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) Class-map: prec3 (match-all) 15004 packets, 1710456 bytes 5 minute offered rate 30000 bps Match: ip precedence 3 --More--   Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af13 (14) Class-map: dscp12 (match-all) 1161 packets, 132354 bytes 5 minute offered rate 2000 bps Match: ip dscp af12 (12) Class-map: class-default (match-any) 36861 packets, 3993870 bytes 5 minute offered rate 77000 bps, drop rate 0 bps Match: any R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7(config-pmap-c-police)#police 5000000 conform-action set-prec-transmit 3 ex$000 conform-action set-prec-transmit 3 exc eed-actiom-action set-prec-transmit 3 exceed-action  set-precet-prec-transmit 3 exceed-action set-prec- transmit ansmit 3 exceed-action set-prec-transmit 1  R7(config-pmap-c-police)#end R7#sh run | *Mar 1 17:19:12.628: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b pol policy-map Prob5 class S5Telnet bandwidth 1000 class JPG shape average 1000000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! --More--   R7# RACK14AS>5 [Resuming connection 5 to r5 ... ] !!!!!!!!!!! S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#do access      sh access-list S5(config)#acccess-list 1 per 180.40.7.130 ^ % Invalid input detected at '^' marker. S5(config)#acccess-list 1 per 180.40.7.130ess-list 1 per 180.40.7.130  S5(config)#access-list 1 per 180.40.7.130           00.1.1.1 S5(config)#class S5(config)#class-map F R4 S5(config-cmap)#matc acc S5(config-cmap)#matc access-group 1 S5(config-cmap)#exit S5(config)#pol S5(config)#policy-map S5(config)#policy-map Prob10 S5(config-pmap)#class S5(config-pmap)#class R4 S5(config-pmap-c)#set ? cos Set IEEE 802.1Q/ISL class of service/user priority dscp Set DSCP in IP(v4) and IPv6 packets ip Set IP specific values precedence Set precedence in IP(v4) and IPv6 packets S5(config-pmap-c)#set cos ? <0-7> cos value S5(config-pmap-c)#set cos 5 S5(config-pmap-c)#int fa 0/24 S5(config-if)#swe  er S5(config-if)#service-policy in Prob10 S5(config-if)#exit S5(config)#mls qos mp ap ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S5(config)#mls qos map dsc S5(config)#mls qos map dscp-co S5(config)#mls qos map dscp-cos ? <0-63> DSCP values separated by spaces (up to 8 values total) S5(config)#mls qos map dscp-cos 12 ? <0-63> DSCP values separated by spaces (up to 8 values total) to Specify COS S5(config)#mls qos map dscp-cos 12 to ? <0-7> cos value S5(config)#mls qos map dscp-cos 12 to 1 S5(config)#mls qos map dscp-cos 12 to 1      26     26 to 2 S5(config)#mls qos map dscp-cos 26 to 2 qos map dscp-cos 26 to 2       ? <0-63> DSCP values separated by spaces (up to 8 values total) S5(config)#mls qos map dscp-cos                      do sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 02 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   S5(config)#mls qos dsc S5(config)#mls qos dsc  S5(config)#mls qos ds    map ds S5(config)#mls qos map dscp-c S5(config)#mls qos map dscp-cos 8 9 10 11 13 14 15 to 3 S5(config)#mls qos map dscp-cos 8 9 10 11 13 14 15 to 3                       16 17 18 19 20 21 22 23 24      to 4 S5(config)#mls qos map dscp-cos 16 17 18 19 20 21 22 23 to 48 9 10 11 13 14 15 to 3 do sh mls qos map  Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 03 03 1 : 03 03 01 03 03 03 04 04 04 04 2 : 04 04 04 04 03 03 02 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   S5(config)#do sh mls qos mapmls qos map dscp-cos 16 17 18 19 20 21 22 23 to 4                            40 41 42 43 44 45 46 47 to 4 S5(config)#mls qos map dscp-cos 40 41 42 43 44 45 46 47 to 4do sh mls qos map  Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 03 03 1 : 03 03 01 03 03 03 04 04 04 04 2 : 04 04 04 04 03 03 02 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 04 04 04 04 04 04 04 04 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   S5(config)#int fa 0/2 3 S5(config-if)#mls ? qos Configure interface QoS parameters S5(config-if)#mls qos ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S5(config-if)#mls qos         wr S5(config-if)#wrr-queue ? bandwidth Configure WRR bandwidth cos-map Configure cos-map for a queue id min-reserve Configure min-reserve level S5(config-if)#wrr-queue cos S5(config-if)#wrr-queue cos-map ? <1-4> enter cos-map queue id S5(config-if)#wrr-queue cos-map 1 ? <0-7> CoS values separated by spaces (up to 8 values total) S5(config-if)#wrr-queue cos-map 1 1 S5(config-if)#wrr-queue cos-map 1 1   2 2 S5(config-if)#3   wrr-queue cos-map 2 2   3 0 3 4 6 7 S5(config-if)#wrr-queue cos-map 3 0 3 4 6 7           4 5 S5(config-if)#or S5(config-if)#or  pri S5(config-if)#priority-queue ? out egress priority queue S5(config-if)#priority-queue ou ? S5(config-if)#priority-queue ou S5(config-if)#wrr S5(config-if)#wrr-queue ? bandwidth Configure WRR bandwidth cos-map Configure cos-map for a queue id min-reserve Configure min-reserve level S5(config-if)#wrr-queue ba S5(config-if)#wrr-queue bandwidth ` ? <1-65536> enter bandwidth weight for qid 1 S5(config-if)#wrr-queue bandwidth 30 30 40 ? <1-65536> enter bandwidth weight for qid 4 S5(config-if)#wrr-queue bandwidth 30 30 40 1 S5(config-if)#^Z S5#sh 23:35:19: %SYS-5-CONFIG_I: Configured from console by console S5#sh qu S5#sh queue? queue queueing S5#sh queue ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface EsconPhy ESCON interface FastEthernet FastEthernet IEEE 802.3 Filter Filter interface Filtergroup Filter Group interface GigabitEthernet GigabitEthernet IEEE 802.3z Group-Async Async Group interface Lex Lex interface LongReachEthernet Long-Reach Ethernet interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Portgroup Portgroup interface Pos-channel POS Channel of interfaces SYSCLOCK Telecom-Bus Clock Controller Tunnel Tunnel interface Vif PGM Multicast Host interface --More--   S5#sh queue a   fa S5#sh queue fastEthernet 0/3 'Show queue' not supported with FIFO queueing. S5#sh queue fastEthernet 0/3                      l mls ? qos Show QoS information S5#sh mls > qos ? aggregate-policer Show aggregate-policer information interface Show interface information maps Show mapping information | Output modifiers S5#sh mls qos int fa 0/3 qu FastEthernet0/3 Egress expedite queue: ena wrr bandwidth weights: qid-weights 1 - 30 2 - 30 3 - 40 4 - 1 when expedite queue is disabled Cos-queue map: cos-qid 0 - 3 1 - 1 2 - 2 3 - 3 4 - 3 5 - 4 6 - 3 7 - 3 S5#sh w? % Unrecognized command S5#sh w qu S5#sh queuei S5#sh queueing ? interface custom custom queueing list configuration fair fair queueing configuration priority priority queueing list configuration random-detect random early detection configuration | Output modifiers S5#sh queueing int ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface EsconPhy ESCON interface FastEthernet FastEthernet IEEE 802.3 Filter Filter interface Filtergroup Filter Group interface GigabitEthernet GigabitEthernet IEEE 802.3z Group-Async Async Group interface Lex Lex interface LongReachEthernet Long-Reach Ethernet interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Portgroup Portgroup interface Pos-channel POS Channel of interfaces SYSCLOCK Telecom-Bus Clock Controller Tunnel Tunnel interface Vif PGM Multicast Host interface --More--   S5#sh queueing int fa ? <0-1> FastEthernet interface number S5#sh queueing int fa 0/3 ? | Output modifiers S5#sh queueing int fa 0/3 Interface FastEthernet0/3 queueing strategy: none S5#sh run | b mls mls qos map dscp-mutation Prob9 14 to 12 mls qos map dscp-mutation Prob9 28 to 26 mls qos map dscp-cos 26 to 2 mls qos map dscp-cos 8 9 10 11 13 14 15 to 3 mls qos map dscp-cos 16 17 18 19 20 21 22 23 to 4 mls qos map dscp-cos 40 41 42 43 44 45 46 47 to 4 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! class-map match-all R4 --More--   match access-group 1 ! ! policy-map Prob10 class R4 set cos 5 ! ! ! interface FastEthernet0/1 switchport mode dynamic desirable ! interface FastEthernet0/2 switchport mode dynamic desirable ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable wrr-queue bandwidth 30 30 40 1 wrr-queue cos-map 1 1 wrr-queue cos-map 2 2 wrr-queue cos-map 3 0 3 4 6 7 wrr-queue cos-map 4 5 --More--   priority-queue out --More--  ! --More--  interface FastEthernet0/4 --More--   switchport mode dynamic desirable --More--  ! --More--  interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 no switchport ip address 208.28.1.2 255.255.255.0 ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 --More--   switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/14 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/15 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/16 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/17 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/18 --More--   switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/19 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/20 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/21 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/22 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/23 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! --More--  interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk service-policy input Prob10 mls qos dscp-mutation Prob9 ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ip http server ip http secure-server --More--  ! ! access-list 1 permit 180.40.7.130 access-list 1 permit 100.1.1.1 ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 privilege level 15 no login line vty 5 15 no login ! ! end S5# S5#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 03 03 1 : 03 03 01 03 03 03 04 04 04 04 2 : 04 04 04 04 03 03 02 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 04 04 04 04 04 04 04 04 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   S5#sh mls qos maprun | b mlsqueueing int fa 0/3 mls qos int fa 0/3 qu FastEthernet0/3 Egress expedite queue: ena wrr bandwidth weights: qid-weights 1 - 30 2 - 30 3 - 40 4 - 1 when expedite queue is disabled Cos-queue map: cos-qid 0 - 3 1 - 1 2 - 2 3 - 3 4 - 3 5 - 4 6 - 3 7 - 3 S5# S5# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b pol policy-map test class dscp24 class dscp26 class dscp28 class prec3 class dscp14 class dscp12 policy-map Prob7 class telnet bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#pol R3(config)#policy-map Prob11 R3(config-pmap)#class DSCP    dscp12 R3(config-pmap-c)#pr R3(config-pmap-c)#priority ? <8-2000000> Kilo Bits per second percent % of total bandwidth R3(config-pmap-c)#priority per 25 ? <32-2000000> Burst in bytes R3(config-pmap-c)#priority per 25 R3(config-pmap-c)#int s 1/2 R3(config-if)#serv out Prob10 1 Policy map Prob7 is already attached R3(config-if)#no serv out Prob7 R3(config-if)#no serv out Prob7serv out Prob11  R3(config-if)#^Z R3# *Mar 1 23:38:03.566: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b pol policy-map test class dscp24 class dscp26 class dscp28 class prec3 class dscp14 class dscp12 policy-map Prob7 class telnet bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 policy-map Prob11 class dscp12 priority percent 25 ! ! ! ! ! ! --More--  interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression active connections 20 --More--   frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob11 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! --More--   R3#sh run | b class class-map match-all dscp26 match dscp af31 class-map match-all dscp14 match ip dscp af13 class-map match-all dscp24 match dscp cs3 class-map match-all telnet match protocol telnet class-map match-all dscp12 match ip dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match access-group 105 ! ! policy-map test class dscp24 class dscp26 class dscp28 class prec3 --More--   R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#st R7(config-if)#standby ? <0-255> group number authentication Authentication delay HSRP initialisation delay ip Enable HSRP and set the virtual IP address mac-address Virtual MAC address name Redundancy name string preempt Overthrow lower priority Active routers priority Priority level redirects Configure sending of ICMP Redirect messages with an HSRP virtual IP address as the gateway IP address timers Hello and hold timers track Priority tracking use-bia HSRP uses interface's burned in address R7(config-if)#standby 47 ? authentication Authentication ip Enable HSRP and set the virtual IP address mac-address Virtual MAC address name Redundancy name string preempt Overthrow lower priority Active routers priority Priority level timers Hello and hold timers track Priority tracking R7(config-if)#standby 47 ip 180  .40.7.132 R7(config-if)#stan R7(config-if)#standby 46 ~7    7 pre R7(config-if)#standby 47 preempt R7(config-if)# *Mar 1 17:57:04.220: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 47 state Standby -> Active R7(config-if)# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/7 S6(config-if)#^Z S6# RACK14AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/3 S5(config-if)#sp S5(config-if)#sp pan S5(config-if)#spanning-tree p S5(config-if)#spanning-tree portp f S5(config-if)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/3 but will only have effect when the interface is in a non-trunking mode. S5(config-if)#^Z S5#^x6 % Unknown command or computer name, or unable to find computer address S5# S5# 23:48:46: %SYS-5-CONFIG_I: Configured from console by console S5# RACK14AS>6 [Resuming connection 6 to r6 ... ] 2 S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/7 S6(config-if)#sp S6(config-if)#span S6(config-if)#spanning-tree po S6(config-if)#spanning-tree portf S6(config-if)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/7 but will only have effect when the interface is in a non-trunking mode. S6(config-if)#^Z S6# 23:50:18: %SYS-5-CONFIG_I: Configured from console by console S6# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#stn R3(config-if)#stn a R3(config-if)#standby 47 ip 180.40.7.132 R3(config-if)#standby 47 ip 180.40.7.132               pri R3(config-if)#standby 47 priority 150 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Listen 180.40.7.131 unknown 180.40.7.132 R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Speak 180.40.7.131 unknown 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#do sh stand brie standby 47 priority 150          e R3(config-if)#standby 47 preempt R3(config-if)# *Mar 1 23:49:14.093: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active R3(config-if)#stan R3(config-if)#standby 47 tr R3(config-if)#standby 47 track ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing R3(config-if)#standby 47 track ser 1/2 ? <1-255> Decrement value R3(config-if)#standby 47 track ser 1/2 51 R3(config-if)#standby 47 track ser 1/2 51 51 0 51 R3(config-if)#^Z R3# *Mar 1 23:49:57.641: %SYS-5-CONFIG_I: Configured from console by console R3#config t         RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#shut R2(config-if)# *Mar 1 23:50:09.088: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Ma R3# *Mar 1 23:50:11.608: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 23:50:12.609: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 99 P Speak 180.40.7.131 unknown 180.40.7.132 R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] *M R7(config-if)#^Z R7#sh stan *Mar 1 18:03:41.663: %SYS-5-CONFIG_I: Configured from console by console R7#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/1 47 100 P Active local 180.40.7.129 180.40.7.132 R7#^x   RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 99 P Standby 180.40.7.131 local 180.40.7.132 R3#sh run int fa 0/0 Building configuration... Current configuration : 288 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/2 51 standby 47 track Serial1/0 51 service-policy input test end R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int fa 0/1 Building configuration... Current configuration : 176 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 end R7# R7# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#track ? <1-500> Tracked object resolution Tracking resolution parameters timer Polling interval timers R3(config)#track 1 ? interface Select an interface to track ip IP protocol R3(config)#track 1  op   ip ? route IP route R3(config)#track 1 ip route ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R3(config)#track 1 ip route 20.10.2.0/24 ? metric Route metric reachability Route reachability state R3(config)#track 1 ip route 20.10.2.0/24 re R3(config)#track 1 ip route 20.10.2.0/24 reachability ? R3(config)#track 1 ip route 20.10.2.0/24 reachability % Cannot change object created via HSRP R3(config)# R3(config)# R3(config)#track 1 ip route 20.10.2.0/24 reachability  ip route 20.10.2.0/24 reachability 2 ip route 20.10.2.0/24 reachability  % Cannot change object created via HSRP R3(config)#track 2 ip route 20.10.2.0/24 reachability  ip route 20.10.2.0/24 reachability 3 ip route 20.10.2.0/24 reachability  R3(config-track)#int fa 0/0          do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:04:11, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.67, 00:04:11, Serial1/0 O 20.10.1.0 [110/782] via 180.40.7.67, 00:04:11, Serial1/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:04:11, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 4 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:04:12, Serial1/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:04:12, FastEthernet0/0 C 180.40.7.64/27 is directly connected, Serial1/0 R3(config-track)#q int fa 0/0 R3(config-if)#stan R3(config-if)#standby 47 tra R3(config-if)#standby 47 track ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing R3(config-if)#standby 47 track 3 ? decrement Priority decrement R3(config-if)#standby 47 track 3 dec R3(config-if)#standby 47 track 3 decrement ? <1-255> Decrement value R3(config-if)#standby 47 track 3 decrement 51 R3(config-if)#^Z R3#sh ru *Mar 1 23:57:41.962: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b track track 3 ip route 20.10.2.0 255.255.255.0 reachability ! ! ! class-map match-all dscp26 match dscp af31 class-map match-all dscp14 match ip dscp af13 class-map match-all dscp24 match dscp cs3 class-map match-all telnet match protocol telnet class-map match-all dscp12 match ip dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match access-group 105 ! ! policy-map test --More--   class dscp24 class dscp26 class dscp28 class prec3 class dscp14 class dscp12 policy-map Prob7 class telnet bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 policy-map Prob11 class dscp12 priority percent 25 ! ! ! ! ! ! interface FastEthernet0/0 --More--   ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/2 51 standby 47 track Serial1/0 51 standby 47 track 3 decrement 51 service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 --More--   R3# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/1 S6(config-if)#shut S6(config-if)# 1d00h: %OSPF-5-ADJCHG: Process 1, Nbr 20.10.2.2 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached S6(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:00:08, FastEthernet0/0 20.0.0.0/24 is subnetted, 1 subnets O 20.10.1.0 [110/782] via 180.40.7.67, 00:00:08, Serial1/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:08, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 4 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:00:08, Serial1/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:00:09, FastEthernet0/0 C 180.40.7.64/27 is directly connected, Serial1/0 R3#sh ip  ip routerun | b trackconfig t sh run int fa 0/0stand brie  P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 48 P Standby 180.40.7.131 local 180.40.7.132 R3# RACK14AS>2 [Resuming connection 2 to r2 ... ] *M R2(config-if)#no shut R2(config-if)#^Z R2# *Mar 1 23:58:58.399: %SYS-5-CONFIG_I: Configured from console by console R2# *Mar 1 23:58:59.657: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 1 23:59:00.659: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 99 P Standby 180.40.7.131 local 180.40.7.132 R3#sh tra R3#sh tra *Mar 1 23:59:10.403: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from LOADING to FULL, Loading Done R3#sh tra? track traffic-shape translate translation-rule R3#sh tra   sta % Ambiguous command: "sh sta" R3#sh stan R3#sh standby FastEthernet0/0 - Group 47 State is Standby 4 state changes, last state change 00:09:06 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.252 secs Preemption enabled Active router is 180.40.7.131, priority 100 (expires in 8.987 sec) Standby router is local Priority 99 (configured 150) Track interface Serial1/2 state Up decrement 51 Track interface Serial1/0 state Up decrement 51 Track object 3 state Down decrement 51 IP redundancy name is "hsrp-Fa0/0-47" (default) R3#sh track Track 1 (via HSRP) Interface Serial1/2 line-protocol Line protocol is Up 3 changes, last change 00:00:50 Tracked by: HSRP FastEthernet0/0 47 Track 2 (via HSRP) Interface Serial1/0 line-protocol Line protocol is Up 1 change, last change 00:10:06 Tracked by: HSRP FastEthernet0/0 47 Track 3 IP route 20.10.2.0 255.255.255.0 reachability Reachability is Down (no route) 2 changes, last change 00:01:26 First-hop interface is unknown Tracked by: HSRP FastEthernet0/0 47 R3#sh trackstandby FastEthernet0/0 - Group 47 State is Standby 4 state changes, last state change 00:09:59 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.880 secs Preemption enabled Active router is 180.40.7.131, priority 100 (expires in 9.615 sec) Standby router is local Priority 99 (configured 150) Track interface Serial1/2 state Up decrement 51 Track interface Serial1/0 state Up decrement 51 Track object 3 state Down decrement 51 IP redundancy name is "hsrp-Fa0/0-47" (default) R3#sh standby track standby  nd brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 99 P Standby 180.40.7.131 local 180.40.7.132 R3# R3# RACK14AS>6 [Resuming connection 6 to r6 ... ] 1 S6(config-if)#no shut S6(config-if)#^Z S6# 1d00h: %SYS-5-CONFIG_I: Configured from console by console S6# 1d00h: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to down S6# 1d00h: RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:02:00, FastEthernet0/0 20.0.0.0/24 is subnetted, 1 subnets O 20.10.1.0 [110/782] via 180.40.7.67, 00:02:00, Serial1/0 [110/782] via 180.40.7.2, 00:02:00, Serial1/2 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:02:00, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:02:01, Serial1/0 [110/781] via 180.40.7.2, 00:02:01, Serial1/2 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:02:01, FastEthernet0/0 C 180.40.7.0/27 is directly connected, Serial1/2 C 180.40.7.64/27 is directly connected, Serial1/0 R3#qsh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:00:02, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.2, 00:00:02, Serial1/2 [110/792] via 180.40.7.67, 00:00:02, Serial1/0 O 20.10.1.0 [110/782] via 180.40.7.67, 00:00:02, Serial1/0 [110/782] via 180.40.7.2, 00:00:02, Serial1/2 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:02, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:00:03, Serial1/0 [110/781] via 180.40.7.2, 00:00:03, Serial1/2 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:00:03, FastEthernet0/0 --More--   R3#sh stand FastEthernet0/0 - Group 47 State is Standby 4 state changes, last state change 00:11:03 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.000 secs Preemption enabled Active router is 180.40.7.131, priority 100 (expires in 8.681 sec) Standby router is local Priority 99 (configured 150) Track interface Serial1/2 state Up decrement 51 Track interface Serial1/0 state Up decrement 51 Track object 3 state Down decrement 51 IP redundancy name is "hsrp-Fa0/0-47" (default) R3# *Mar 2 00:01:26.330: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active R3# sh stand FastEthernet0/0 - Group 47 State is Active 5 state changes, last state change 00:00:03 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 2.387 secs Preemption enabled Active router is local Standby router is unknown Priority 150 (configured 150) Track interface Serial1/2 state Up decrement 51 Track interface Serial1/0 state Up decrement 51 Track object 3 state Up decrement 51 IP redundancy name is "hsrp-Fa0/0-47" (default) R3# sh stand   RACK14AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv rotue  r    uter ? ospf Open Shortest Path First (OSPF) rip IPv6 Routing Information Protocol (RIPv6) R1(config)#ipv router ospf 1 % IPv6 routing not enabled R1(config)#ipv rout    un R1(config)#ipv unicast-routing R1(config)#ipv unicast-routing router ospf 1  R1(config)#ipv router ospf 1 R1(config)#ipv router ospf 1 R1(config)#ipv router ospf 1 R1(config)#ipv router ospf 1 R1(config)#ipv router ospf 1unicast-routing router ospf 1 unicast-routing nipv unicast-routing oipv unicast-routing  ipv unicast-routing  R1(config)#^Z R1# *Mar 2 00:05:42.762: %SYS-5-CONFIG_I: Configured from console by console R1# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/. 0 R3(config-if)#vrr R3(config-if)#vrrp ? <1-255> Group number R3(config-if)#vrrp 47 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R3(config-if)#vrrp 47 ip ? A.B.C.D VRRP group IP address R3(config-if)#vrrp 47 ip 180.40.7.133 R3(config-if)# *Mar 2 00:06:29.911: %VRRP-6-STATECHANGE: Fa0/0 Grp 47 state Init -> Backup R3(config-if)#vrrp 47 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R3(config-if)#vrrp 47 *Mar 2 00:06:33.521: %VRRP-6-STATECHANGE: Fa0/0 Grp 47 state Backup -> Master R3(config-if)#vrrp 47 pri 150 R3(config-if)#vrrp 47 pri 150      sh    do    ^Z R3#^x7 % Unknown command or computer name, or unable to find computer address R3# *Mar 2 00:07:13.803: %SYS-5-CONFIG_I: Configured from console by console R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#config t ^ % Invalid input detected at '^' marker. R7(config)#int fa0/1 R7(config-if)#vrrp ? <1-255> Group number R7(config-if)#vrrp 47 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R7(config-if)#vrrp 47 pri R7(config-if)#vrrp 47 priority ? <1-254> Priority level R7(config-if)#vrrp 47 priority 100 ? R7(config-if)#vrrp 47 priority 100                      ^Z R7#sh *Mar 1 18:21:13.071: %SYS-5-CONFIG_I: Configured from console by console R7#sh vrrp brie Interface Grp Pri Time Own Pre State Master addr Group addr R7#sh vrrp brie config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#ver  rrp 47 ip 180.40.7.133 R7(config-if)#^Z R7# *Mar 1 18:21:33.084: %VRRP-6-STATECHANGE: Fa0/1 Grp 47 state Init -> Backup R7# *Mar 1 18:21:33.837: %SYS-5-CONFIG_I: Configured from console by console R7#sh config tsh vrrp brie Interface Grp Pri Time Own Pre State Master addr Group addr Fa0/1 47 100 3609 Y Backup 180.40.7.129 180.40.7.133 R7# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int fa 0               ^x4 % Unknown command or computer name, or unable to find computer address R3# R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#ping 180.40.7.132 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.132, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R4# *Mar 2 00:12:05.993: IP: s=180.40.7.130 (local), d=180.40.7.132, len 100, policy match *Mar 2 00:12:05.993: IP: route map Prob2, item 10, permit *Mar 2 00:12:05.993: IP: s=180.40.7.130 (local), d=180.40.7.132 (FastEthernet0/0), len 100, policy routed *Mar 2 00:12:05.993: IP: local to FastEthernet0/0 180.40.7.129 *Mar 2 00:12:06.001: IP: s=180.40.7.130 (local), d=180.40.7.132, len 100, policy match *Mar 2 00:12:06.001: IP: route map Prob2, item 10, permit *Mar 2 00:12:06.001: IP: s=180.40.7.130 (local), d=180.40.7.132 (FastEthernet0/0), len 100, policy routed *Mar 2 00:12:06.001: IP: local to FastEthernet0/0 180.40.7.129 *Mar 2 00:12:06.005: IP: s=180.40.7.130 (local), d=180.40.7.132, len 100, policy match *Mar 2 00:12:06.005: IP: route map Prob2, item 10, permit *Mar 2 00:12:06.005: IP: s=180.40.7.130 (local), d=180.40.7.132 (FastEthernet0/0), len 100, policy routed *Mar 2 00:12:06.009: IP: local to FastEthernet0/0 180.40.7.129 *Mar 2 00:12:06.013: IP: s=180.40.7.130 (local), d=180.40.7.132, len 100, policy match *Mar 2 00:12:06.013: IP: route map Prob2, item 10, permit *Mar 2 00:12:06.013: IP: s=180.40.7.130 (local), d=180.40.7.132 (FastEthernet0/0), len 100, policy routed *Mar 2 00:12:06.013: IP: local to FastEthernet0/0 180.40.7.129 *Mar 2 00:12:06.017: IP: s=180.40.7.130 (local), d=180.40.7.132, len 100, policy match *Mar 2 00:12:06.021: IP: route map Prob2, item 10, permit *Mar 2 00:12:06.021: IP: s=180.40.7.130 (local), d=180.40.7.132 (FastEthernet0/0), len 100, policy routed *Mar 2 00:12:06.021: IP: local to FastEthernet0/0 180.40.7.129 R4# R4#u all All possible debugging has been turned off R4#configf t ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#do sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 145 0013.60e3.f021 ARPA FastEthernet0/0 Internet 180.40.7.130 - 0002.4bcb.56e0 ARPA FastEthernet0/0 Internet 180.40.7.129 14 0013.7f15.f280 ARPA FastEthernet0/0 R4(config)#no ip local route Prob2 ^ % Invalid input detected at '^' marker. R4(config)#no ip local route Prob22           ? policy Enable policy routing pool IP Local address pool lists R4(config)#no ip local po R4(config)#no ip local pol R4(config)#no ip local policy route Prob2 R4(config)#^Z R4#config tf t *Mar 2 00:12:59.877: %SYS-5-CONFIG_I: Configured from console by console R4#configf tu all ping 180.40.7.132 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.132, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 4/4/4 ms R4#ping 180.40.7.132 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.133, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 4/4/4 ms R4#sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 146 0013.60e3.f021 ARPA FastEthernet0/0 Internet 180.40.7.130 - 0002.4bcb.56e0 ARPA FastEthernet0/0 Internet 180.40.7.129 15 0013.7f15.f280 ARPA FastEthernet0/0 Internet 180.40.7.133 0 0000.5e00.012f ARPA FastEthernet0/0 Internet 180.40.7.132 0 0000.0c07.ac2f ARPA FastEthernet0/0 R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int fa 0/0 Building configuration... Current configuration : 368 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 47 ip 180.40.7.133 vrrp 47 priority 150 standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/2 51 standby 47 track Serial1/0 51 standby 47 track 3 decrement 51 service-policy input test end R3# RACK14AS>6 7 [Resuming connection 7 to r7 ... ] R7#sh run int fa 0/1 Building configuration... Current configuration : 201 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 47 ip 180.40.7.133 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 end R7# R7#^x3 % Unknown command or computer name, or unable to find computer address R7# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip dhcp ? aaa Configure aaa attributes binding DHCP address bindings bootp BOOTP specific configuration conflict DHCP address conflict parameters database Configure DHCP database agents excluded-address Prevent DHCP from assigning certain addresses limited-broadcast-address Use all 1's broadcast address ping Specify ping parameters used by DHCP pool Configure DHCP address pools relay DHCP relay agent parameters smart-relay Enable Smart Relay feature R3(config)#ip dhcp ex R3(config)#ip dhcp excluded-address ? A.B.C.D Low IP address R3(config)#ip dhcp excluded-address 180.40.7.129 R3(config)#ip dhcp excluded-address 180.40.7.129    31 180.40.7.143  34 R3(config)#ip dhcp pool ? WORD Pool name R3(config)#ip dhcp pool Prob15 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   utilization Configure various utilization parameters vrf Associate this pool with a VRF R3(dhcp-config)#net R3(dhcp-config)#netw R3(dhcp-config)#network > ? A.B.C.D Network number in dotted-decimal notation R3(dhcp-config)#network 180.49 0.7.128 ? /nn or A.B.C.D Network mask or prefix length R3(dhcp-config)#network 180.40.7.128 /27 R3(dhcp-config)#def R3(dhcp-config)#default-router ? Hostname or A.B.C.D Router's name or IP address R3(dhcp-config)#default-router   180.40.7.132 R3(dhcp-config)#dom R3(dhcp-config)#domain-name ? WORD Domain name R3(dhcp-config)#domain-name cciestudent.com R3(dhcp-config)#dns R3(dhcp-config)#dns-server ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#dns-server 208.28.1.83 2 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   utilization Configure various utilization parameters vrf Associate this pool with a VRF R3(dhcp-config)#op ? <0-254> DHCP option code R3(dhcp-config)#op 150 ? ascii Data is an NVT ASCII string hex Data is a hexadecimal string instance Specify the option instance ip Data is one or more IP addresses R3(dhcp-config)#op 150 ip ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#op 150 ip 20.20.20.20 ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#op 150 ip 20.20.20.20 R3(dhcp-config)#^Z R3# *Mar 2 00:18:11.221: %SYS-5-CONFIG_I: Configured from console by console R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#confi gt ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#ip dh  add R4(config-if)#ip address ? A.B.C.D IP address dhcp IP Address negotiated via DHCP pool IP Address autoconfigured from a local DHCP pool R4(config-if)#ip address dh R4(config-if)#ip address dhcp ? client-id Specify client-id to use hostname Specify value for hostname option R4(config-if)#ip address dhcp cli R4(config-if)#ip address dhcp client-id ? FastEthernet FastEthernet IEEE 802.3 R4(config-if)#ip address dhcp client-id fa R4(config-if)#ip address dhcp client-id fastEthernet ? <0-6> FastEthernet interface number R4(config-if)#ip address dhcp client-id fastEthernet 0/0 ? hostname Specify value for hostname option R4(config-if)#ip address dhcp client-id fastEthernet 0/0 R4(config-if)# *Mar 2 00:21:38.253: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 00:21:38.257: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from EXSTART to DOWN, Neighbor Down: Interface down or detached R4(config-if)#do deb ip    dhcp DHCP client activity debugging is on R4(config-if)# *Mar 2 00:21:45.285: DHCP: Received a BOOTREP pkt *Mar 2 00:21:45.289: DHCP: offer received from 180.40.7.129 *Mar 2 00:21:45.289: DHCP: SRequest attempt # 1 for entry: *Mar 2 00:21:45.289: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 00:21:45.289: DHCP: SRequest- Requested IP addr option: 180.40.7.130 *Mar 2 00:21:45.289: DHCP: SRequest placed lease len option: 86400 *Mar 2 00:21:45.289: DHCP: SRequest: 292 bytes *Mar 2 00:21:45.289: DHCP: SRequest: 292 bytes *Mar 2 00:21:45.289: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 00:21:45.301: DHCP: Received a BOOTREP pkt R4(config-if)# *Mar 2 00:21:49.309: DHCP Client Pooling: ***Allocated IP address: 180.40.7.130 *Mar 2 00:21:49.357: Allocated IP address = 180.40.7.130 255.255.255.224 R4(config-if)# *Mar 2 00:21:49.357: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.224, hostname R4 R4(config-if)# *Mar 2 00:22:08.325: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)# *Mar 2 00:22:11.945: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)#do sh ip int fa 0/0 FastEthernet0/0 is up, line protocol is up Internet address is 180.40.7.130/27 Broadcast address is 255.255.255.255 Address determined by DHCP MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Multicast reserved groups joined: 224.0.0.5 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF Feature Fast switching turbo vector IP multicast fast switching is enabled --More--   IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is disabled WCCP Redirect outbound is disabled WCCP Redirect inbound is disabled WCCP Redirect exclude is disabled BGP Policy Mapping is disabled R4(config-if)#no    shut *Mar 2 00:22:52.317: DHCP: SRelease attempt # 1 for entry: *Mar 2 00:22:52.317: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 00:22:52.317: DHCP: SRelease: 259 bytes *Mar 2 00:22:52.381: DHCP: SRelease attempt # 2 for entry: *Mar 2 00:22:52.381: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 00:22:52.381: DHCP: SRelease: 259 bytes *Mar 2 00:22:53.317: DHCP: SRelease attempt # 3 for entry: *Mar 2 00:22:53.317: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 00:22:53.317: DHCP: SRelease: 259 bytes R4(config-if)#no shut R4(config-if)# *Mar 2 00:22:54.385: RAC: DHCP stopped on interface FastEthernet0/0 *Mar 2 00:22:54.385: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 00:22:54.385: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)# *Mar 2 00:22:54.569: DHCP: DHCP client process started: 10 *Mar 2 00:22:54.569: RAC: Delaying starting DHCP because interface FastEthernet0/0 not up R4(config-if)# *Mar 2 00:22:56.389: DHCP: DHCP client process started: 10 *Mar 2 00:22:56.389: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 00:22:56.393: DHCP: Try 1 to acquire address for FastEthernet0/0 *Mar 2 00:22:56.405: DHCP: allocate request *Mar 2 00:22:56.405: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 00:22:56.409: DHCP: new entry. add to queue *Mar 2 00:22:56.409: DHCP: SDiscover attempt # 1 for entry: *Mar 2 00:22:56.409: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:22:56.409: DHCP: SDiscover 274 bytes *Mar 2 00:22:56.409: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4(config-if)# *Mar 2 00:22:59.409: DHCP: SDiscover attempt # 2 for entry: *Mar 2 00:22:59.409: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:22:59.409: DHCP: SDiscover 274 bytes *Mar 2 00:22:59.409: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4(config-if)# *Mar 2 00:23:02.409: DHCP: SDiscover attempt # 3 for entry: *Mar 2 00:23:02.409: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:23:02.409: DHCP: SDiscover 274 bytes *Mar 2 00:23:02.409: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4(config-if)#%Unknown DHCP problem.. No allocation possible *Mar 2 00:23:16.889: DHCP: Waiting for 5 seconds on interface FastEthernet0/0 R4(config-if)# *Mar 2 00:23:21.889: DHCP: Try 2 to acquire address for FastEthernet0/0 *Mar 2 00:23:21.901: DHCP: allocate request *Mar 2 00:23:21.901: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 00:23:21.901: DHCP: new entry. add to queue *Mar 2 00:23:21.905: DHCP: SDiscover attempt # 1 for entry: *Mar 2 00:23:21.905: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:23:21.905: DHCP: SDiscover 274 bytes *Mar 2 00:23:21.905: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4(config-if)# *Mar 2 00:23:24.317: DHCP: deleting entry 63055420 0.0.0.0 from list *Mar 2 00:23:24.905: DHCP: SDiscover attempt # 2 for entry: *Mar 2 00:23:24.905: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:23:24.905: DHCP: SDiscover 274 bytes *Mar 2 00:23:24.905: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4(config-if)# *Mar 2 00:23:27.905: DHCP: SDiscover attempt # 3 for entry: *Mar 2 00:23:27.905: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:23:27.905: DHCP: SDiscover 274 bytes *Mar 2 00:23:27.905: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4(config-if)#%Unknown DHCP problem.. No allocation possible *Mar 2 00:23:42.385: DHCP: Waiting for 10 seconds on interface FastEthernet0/0 R4(config-if)# *Mar 2 00:23:46.889: DHCP: deleting entry 629E287C 0.0.0.0 from list R4(config-if)# *Mar 2 00:23:52.385: DHCP: Try 3 to acquire address for FastEthernet0/0 *Mar 2 00:23:52.397: DHCP: allocate request *Mar 2 00:23:52.397: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 00:23:52.397: DHCP: new entry. add to queue *Mar 2 00:23:52.401: DHCP: SDiscover attempt # 1 for entry: *Mar 2 00:23:52.401: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:23:52.401: DHCP: SDiscover 274 bytes *Mar 2 00:23:52.401: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4(config-if)# *Mar 2 00:23:54.409: DHCP: Received a BOOTREP pkt *Mar 2 00:23:54.409: DHCP: offer received from 180.40.7.129 *Mar 2 00:23:54.409: DHCP: SRequest attempt # 1 for entry: *Mar 2 00:23:54.413: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 00:23:54.413: DHCP: SRequest- Requested IP addr option: 180.40.7.135 *Mar 2 00:23:54.413: DHCP: SRequest placed lease len option: 86400 *Mar 2 00:23:54.413: DHCP: SRequest: 292 bytes *Mar 2 00:23:54.413: DHCP: SRequest: 292 bytes *Mar 2 00:23:54.413: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 00:23:54.421: DHCP: Received a BOOTREP pkt R4(config-if)# *Mar 2 00:23:58.429: DHCP Client Pooling: ***Allocated IP address: 180.40.7.135 *Mar 2 00:23:58.545: Allocated IP address = 180.40.7.135 255.255.255.224 R4(config-if)# *Mar 2 00:23:58.545: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.135, mask 255.255.255.224, hostname R4 R4(config-if)# *Mar 2 00:24:07.445: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)# *Mar 2 00:24:11.981: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)#^Z R4#config t *Mar 2 00:24:12.385: DHCP: deleting entry 622304EC 0.0.0.0 from list R4#config t gtsh arp  *Mar 2 00:24:13.261: %SYS-5-CONFIG_I: Configured from console by console R4#sh arpping 180.40.7.133sh arp confi gtg t deb dhcp ? detail DHCP packet content R4#deb dhcp de DHCP client activity debugging is on (detailed) R4#confi g ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# RACK14AS>6 [Resuming connection 6 to r6 ... ] INK-3-UPDOWN: Int S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/4 S6(config-if)#span S6(config-if)#spanning-tree po S6(config-if)#spanning-tree port % Ambiguous command: "spanning-tree port" S6(config-if)#spanning-tree portf S6(config-if)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/4 but will only have effect when the interface is in a non-trunking mode. S6(config-if)#^Z S6# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4(config)#int fa 0/0 R4(config-if)#shut *Mar 2 00:24:42.861: DHCP: SRelease attempt # 1 for entry: *Mar 2 00:24:42.861: Temp IP addr: 180.40.7.135 for peer on Interface: FastEthernet0/0 *Mar 2 00:24:42.861: Temp sub net mask: 255.255.255.224 *Mar 2 00:24:42.865: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 00:24:42.865: DHCP transaction id: 53B5D19 *Mar 2 00:24:42.865: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 00:24:42.865: Temp default-gateway addr: 180.40.7.132 *Mar 2 00:24:42.865: Next timer fires after: 00:00:00 *Mar 2 00:24:42.865: Retry count: 1 Client-ID: 0002.4bcb.56e0 *Mar 2 00:24:42.865: Hostname: R4 *Mar 2 00:24:42.865: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 00:24:42.865: DHCP: SRelease: 259 bytes *Mar 2 00:24:42.933: DHCP: SRelease attempt # 2 for entry: *Mar 2 00:24:42.933: Temp IP addr: 180.40.7.135 for peer on Interface: FastEthernet0/0 *Mar 2 00:24:42.933: Temp sub net mask: 255.255.255.224 *Mar 2 00:24:42.933: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 00:24:42.933: DHCP transaction id: 53B5D19 *Mar 2 00:24:42.933: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 00:24:42.933: Temp default-gateway addr: 180.40.7.132 *Mar 2 00:24:42.933: Next timer fires after: 00:00:00 *Mar 2 00:24:42.933: Retry count: 2 Client-ID: 0002.4bcb.56e0 *Mar 2 00:24:42.933: Hostname: R4 *Mar 2 00:24:42.937: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 00:24:42.937: DHCP: SRelease: 259 bytes *Mar 2 00:24:42.937: DHCP: Releasing ipl options: *Mar 2 00:24:42.937: Clearing default gateway and route to 180.40.7.132 *Mar 2 00:24:42.937: Removing old default route 180.40.7.132 *Mar 2 00:24:42.941: Clearing DNS address 208.28.1.82 *Mar 2 00:24:42.941: Clearing default domain of cciest R4(config-if)#no shutudent.com *Mar 2 00:24:43.861: DHCP: SRelease attempt # 3 for entry: *Mar 2 00:24:43.861: Temp IP addr: 180.40.7.135 for peer on Interface: FastEthernet0/0 *Mar 2 00:24:43.861: Temp sub net mask: 255.255.255.224 *Mar 2 00:24:43.861: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 00:24:43.861: DHCP transaction id: 53B5D19 *Mar 2 00:24:43.861: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 00:24:43.861: Next timer fires after: 00:00:01 *Mar 2 00:24:43.861: Retry count: 3 Client-ID: 0002.4bcb.56e0 *Mar 2 00:24:43.861: Hostname: R4 *Mar 2 00:24:43.865: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 00:24:43.865: DHCP: SRelease: 259 bytes *Mar 2 00:24:44.941: RAC: DHCP stopped on interface FastEthernet0/0 R4(config-if)#no shut *Mar 2 00:24:44.941: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 00:24:44.941: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#no shut *Mar 2 00:24:46.945: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 2 00:24:47.945: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R4(config-if)#no shut R4(config-if)#^Z R4#u *Mar 2 00:24:56.245: DHCP: DHCP client process started: 10 *Mar 2 00:24:56.245: RAC: Delaying starting DHCP because interface FastEthernet0/0 not up R4#u all All possible debugging has been turned off R4# *Mar 2 00:24:57.497: %SYS-5-CONFIG_I: Configured from console by console *Mar 2 00:24:58.237: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 2 00:24:58.237: DHCP: DHCP client process started: 10 *Mar 2 00:24:58.241: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 00:24:58.241: DHCP: Try 1 to acquire address for FastEthernet0/0 *Mar 2 00:24:58.257: DHCP: allocate request *Mar 2 00:24:58.257: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 00:24:58.257: DHCP: new entry. add to queue *Mar 2 00:24:58.257: DHCP: SDiscover attempt # 1 for entry: *Mar 2 00:24:58.257: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 00:24:58.257: Temp sub net mask: 0.0.0.0 *Mar 2 00:24:58.257: DHCP Lease server: 0.0.0.0, state: 1 Selecting R4# *Mar 2 00:24:58.257: DHCP transaction id: 53D42BF *Mar 2 00:24:58.257: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 00:24:58.261: Next timer fires after: 00:00:03 *Mar 2 00:24:58.261: Retry count: 1 Client-ID: 0002.4bcb.56e0 *Mar 2 00:24:58.261: Hostname: R4 *Mar 2 00:24:58.261: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:24:58.261: DHCP: SDiscover 274 bytes *Mar 2 00:24:58.261: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4# *Mar 2 00:24:59.237: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip dhcp bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.136 0100.024b.cb56.e0 Mar 03 1993 12:22 AM Automatic R3# *Mar 2 00:22:52.202: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3# *Mar 2 00:22:57.631: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int     ip dhcp pool R4 R3(dhcp-config)#cli R3(dhcp-config)#client-i R3(dhcp-config)#client-identifier Client-ID: 0002.4bcb.56e0 ^ % Invalid input detected at '^' marker. R3(dhcp-config)#client-identifier Client-ID: 0002.4bcb.56e0                          0100.024b.cb56.e0 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#host ? A.B.C.D IP address in dotted-decimal notation R3(dhcp-config)#host 180.40.7.130 ? /nn or A.B.C.D Network mask or prefix length R3(dhcp-config)#host 180.40.7.130 /24 R3(dhcp-config)#^Z R3#sh *Mar 2 00:25:21.699: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip dhcp bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 0100.024b.cb56.e0 Infinite Manual 180.40.7.136 0100.024b.cb56.e0 Mar 03 1993 12:22 AM Automatic R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] *M R4#h sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.136 YES DHCP up up ATM1/0 unassigned YES unset administratively down down Loopback0 100.1.1.1 YES manual up up R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int s fa 0/0 R4(config-if)#no shu      shut R4(config-if)# *Mar 2 00:29:46.257: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 00:29:46.257: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)# *Mar 2 00:29:48.261: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 2 00:29:49.261: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R4(config-if)#no shut R4(config-if)#^Z R4# *Mar 2 00:29:53.609: %SYS-5-CONFIG_I: Configured from console by console R4# *Mar 2 00:29:54.969: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 2 00:29:55.969: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R4# *Mar 2 00:30:02.033: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.0, hostname R4 R4#x  RACK14AS>3 [Resuming connection 3 to r3 ... ] R3# *Mar 2 00:27:56.480: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired R3#sh run | b dhc ip dhcp excluded-address 180.40.7.129 ip dhcp excluded-address 180.40.7.131 180.40.7.134 ! ip dhcp pool Prob15 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 domain-name cciestudent.com dns-server 208.28.1.82 option 150 ip 20.20.20.20 ! ip dhcp pool R4 host 180.40.7.130 255.255.255.0 client-identifier 0100.024b.cb56.e0 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! ! ! ! --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#host 180.40.7.130 /24client-identifier 0100.024b.cb56.e0Client-ID: 0002.4bcb.56e0ip dhcp pool R4  R3(dhcp-config)#ip dhcp pool R4host 180.40.7.130 /24nhost 180.40.7.130 /24ohost 180.40.7.130 /24 host 180.40.7.130 /24 R3(dhcp-config)#no host 180.40.7.130 /24 7no host 180.40.7.130 /27  host 180.40.7.130 /27  R3(dhcp-config)#^Z R3# *Mar 2 00:28:31.462: %SYS-5-CONFIG_I: Configured from console by console R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#shut R4(config-if)#deb dhcp d *Mar 2 00:31:15.649: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 2 00:31:16.649: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R4(config-if)#deb dhcp de ^ % Invalid input detected at '^' marker. R4(config-if)#deb dhcp deddeb dhcp deodeb dhcp de deb dhcp de DHCP client activity debugging is on (detailed) R4(config-if)#no shut R4(config-if)#^Z R4# *Mar 2 00:31:23.641: DHCP: DHCP client process started: 10 *Mar 2 00:31:23.641: RAC: Delaying starting DHCP because interface FastEthernet0/0 not up R4# *Mar 2 00:31:23.977: %SYS-5-CONFIG_I: Configured from console by console R4# *Mar 2 00:31:25.633: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 2 00:31:25.633: DHCP: DHCP client process started: 10 *Mar 2 00:31:25.633: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 00:31:25.637: DHCP: Try 1 to acquire address for FastEthernet0/0 *Mar 2 00:31:25.649: DHCP: allocate request *Mar 2 00:31:25.653: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 00:31:25.653: DHCP: new entry. add to queue *Mar 2 00:31:25.653: DHCP: SDiscover attempt # 1 for entry: *Mar 2 00:31:25.653: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 00:31:25.653: Temp sub net mask: 0.0.0.0 *Mar 2 00:31:25.653: DHCP Lease server: 0.0.0.0, state: 1 Selecting R4# *Mar 2 00:31:25.653: DHCP transaction id: 54325AE *Mar 2 00:31:25.653: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 00:31:25.653: Next timer fires after: 00:00:03 *Mar 2 00:31:25.653: Retry count: 1 Client-ID: 0002.4bcb.56e0 *Mar 2 00:31:25.653: Hostname: R4 *Mar 2 00:31:25.657: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:31:25.657: DHCP: SDiscover 274 bytes *Mar 2 00:31:25.657: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4# *Mar 2 00:31:26.633: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R4# *Mar 2 00:31:28.653: DHCP: SDiscover attempt # 2 for entry: *Mar 2 00:31:28.653: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 00:31:28.653: Temp sub net mask: 0.0.0.0 *Mar 2 00:31:28.653: DHCP Lease server: 0.0.0.0, state: 1 Selecting *Mar 2 00:31:28.653: DHCP transaction id: 54325AE *Mar 2 00:31:28.653: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 00:31:28.653: Next timer fires after: 00:00:03 *Mar 2 00:31:28.653: Retry count: 2 Client-ID: 0002.4bcb.56e0 *Mar 2 00:31:28.653: Hostname: R4 *Mar 2 00:31:28.653: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 00:31:28.657: DHCP: SDiscover 274 bytes *Mar 2 00:31:28.657: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 00:31:28.661: DHCP: Received a BOOTREP pkt *Mar 2 00:31:28.661: DHCP: Scan: Message type: DHCP Offer *Mar 2 00:31:28.661: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 00:31:28.665: DHCP: Sc R4#an: Lease Time: 86400 *Mar 2 00:31:28.665: DHCP: Scan: Renewal time: 43200 *Mar 2 00:31:28.665: DHCP: Scan: Rebind time: 75600 *Mar 2 00:31:28.665: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 00:31:28.665: DHCP: Scan: Router Option: 180.40.7.132 *Mar 2 00:31:28.665: DHCP: Scan: Domain Name: cciestudent.com *Mar 2 00:31:28.665: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 00:31:28.665: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 00:31:28.665: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 00:31:28.665: UDP sport: 43, dport: 44, length: 317 *Mar 2 00:31:28.665: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 00:31:28.665: DHCP server identifier: 180.40.7.129 *Mar 2 00:31:28.669: xid: 54325AE, secs: 0, flags: 8000 *Mar 2 00:31:28.669: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 00:31:28.669: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 00:31:28.669: options block length: 69 *Mar 2 00:31:28.669: DHCP Offer Message Offered Address: 180.40.7.130 *Mar 2 00:31:28.669: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 00:31:28.669: DHCP: Server ID Option: 180.40.7.129 *Mar 2 00:31:28.669: DHCP: offer received from 180.40.7.129 *Mar 2 00:31:28.669: DHCP: SRequest attempt # 1 for entry: *Mar 2 00:31:28.669: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 00:31:28.673: Temp sub net mask: 255.255.255.224 *Mar 2 00:31:28.673: DHCP Lease server: 180.40.7.129, state: 2 Requesting *Mar 2 00:31:28.673: DHCP transaction id: 54325AE *Mar 2 00:31:28.673: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 00:31:28.673: Next timer fires after: 00:00:01 *Mar 2 00:31:28.673: Retry count: 1 Client-ID: 0002.4bcb.56e0 *Mar 2 00:31:28.673: Hostname: R4 *Mar 2 00:31:28.673: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 00:31:28.673: DHCP: SRequest- Requested IP addr option: 180.40.7.130 *Mar 2 00:31:28.673: DHCP: SRequest placed lease len option: 86400 *Mar 2 00:31:28.673: DHCP: SRequest: 292 bytes *Mar 2 00:31:28.677: DHCP: SRequest: 292 bytes *Mar 2 00:31:28.677: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 00:31:28.681: DHCP: Received a BOOTREP pkt *Mar 2 00:31:28.681: DHCP: Scan: Message type: DHCP Ack *Mar 2 00:31:28.681: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 00:31:28.685: DHCP: Scan: Lease Time: 86400 *Mar 2 00:31:28.685: DHCP: Scan: Renewal time: 43200 *Mar 2 00:31:28.685: DHCP: Scan: Rebind time: 75600 *Mar 2 00:31:28.685: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 00:31:28.685: DHCP: Scan: Router Option: 180.40.7.132 *Mar 2 00:31:28.685: DHCP: Scan: Domain Name: cciestudent.com *Mar 2 00:31:28.685: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 00:31:28.685: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 00:31:28.685: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 00:31:28.685: UDP sport: 43, dport: 44, length: 317 *Mar 2 00:31:28.685: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 00:31:28.685: DHCP server identifier: 180.40.7.129 *Mar 2 00:31:28.689: xid: 54325AE, secs: 0, flags: 8000 *Mar 2 00:31:28.689: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 00:31:28.689: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 00:31:28.689: options block length: 69 *Mar 2 00:31:28.689: DHCP Ack Message *Mar 2 00:31:28.689: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 00:31:28.689: DHCP: Server ID Option: 180.40.7.129 *Mar 2 00:31:31.697: DHCP: Releasing ipl options: *Mar 2 00:31:31.697: DHCP: Applying DHCP options: *Mar 2 00:31:31.701: Setting default_gateway to 180.40.7.132 *Mar 2 00:31:31.701: Adding default route 180.40.7.132 *Mar 2 00:31:32.701: Adding DNS server address 208.28.1.82 *Mar 2 00:31:32.701: Setting default domain to cciestudent.com *Mar 2 00:31:32.701: DHCP Client Pooling: ***Allocated IP address: 180.40.7.130 *Mar 2 00:31:32.825: Allocated IP address = 180.40.7.130 255.255.255.224 *Mar 2 00:31:32.825: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.224, hostname R4 R4# R4# *Mar 2 00:31:41.713: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 00:31:42.005: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4# *Mar 2 00:31:43.577: DHCP: QScan: Purging entry *Mar 2 00:31:43.577: DHCP: deleting entry 629E287C 0.0.0.0 from list *Mar 2 00:31:43.577: Temp IP addr: 0.0.0.0 for peer on Interface: unknown *Mar 2 00:31:43.577: Temp sub net mask: 255.255.255.0 *Mar 2 00:31:43.577: DHCP Lease server: 180.40.7.129, state: 8 Purging *Mar 2 00:31:43.577: DHCP transaction id: 541D0DE *Mar 2 00:31:43.577: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 00:31:43.577: Temp default-gateway addr: 180.40.7.132 *Mar 2 00:31:43.577: No timer running *Mar 2 00:31:43.577: Retry count: 0 Client-ID: *Mar 2 00:31:43.577: Hostname: R4 R4#u all All possible debugging has been turned off R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 180.40.7.132 to network 0.0.0.0 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.131, 00:00:24, FastEthernet0/0 [110/793] via 180.40.7.129, 00:00:24, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.131, 00:00:24, FastEthernet0/0 [110/783] via 180.40.7.129, 00:00:24, FastEthernet0/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:24, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.131, 00:00:25, FastEthernet0/0 [110/782] via 180.40.7.129, 00:00:25, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:00:25, FastEthernet0/0 --More--  O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:25, FastEthernet0/0 O 180.40.7.64/27 [110/782] via 180.40.7.129, 00:00:25, FastEthernet0/0 [110/782] via 180.40.7.131, 00:00:25, FastEthernet0/0 S* 0.0.0.0/0 [254/0] via 180.40.7.132 R4#sh run Building configuration... Current configuration : 1257 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R4 ! boot-start-marker boot-end-marker ! ! no aaa new-model ip subnet-zero ! ! ip cef no ip domain lookup ! ip audit po max-events 100 ! --More--  ! ! ! ! ! ! ! ! ! ! ! ! ! class-map match-all dscp26 match dscp af31 class-map match-all dscp24 match dscp cs3 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 ! ! --More--  policy-map test class dscp24 class dscp26 class dscp28 class prec3 ! ! ! ! ! interface Loopback0 ip address 100.1.1.1 255.255.255.0 ! interface FastEthernet0/0 ip address dhcp client-id FastEthernet0/0 duplex auto speed auto service-policy input test ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive --More--   R4#^x6 % Unknown command or computer name, or unable to find computer address R4# R4# RACK14AS>6 [Resuming connection 6 to r6 ... ] 1d0 S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 164 R S 2611XM Fas 0/1 R1 Fas 0/1 144 R 2611 Eth 0/1 R7 Fas 0/7 156 R S 2611XM Fas 0/1 R4 Fas 0/4 130 R 3620 Fas 0/0 S5 Fas 0/24 178 R S I WS-C3550-2Fas 0/24 S6#sh cdp nei sh cdp nei d ------------------------- Device ID: R2 Entry address(es): IP address: 20.10.1.1 Platform: cisco 2611XM, Capabilities: Router Switch Interface: FastEthernet0/2, Port ID (outgoing port): FastEthernet0/1 Holdtime : 161 sec Version : Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller advertisement version: 2 VTP Management Domain: '' Duplex: full Management address(es): ------------------------- Device ID: R1 --More--  Entry address(es): IP address: 20.10.2.2 Platform: cisco 2611, Capabilities: Router Interface: FastEthernet0/1, Port ID (outgoing port): Ethernet0/1 Holdtime : 138 sec Version : Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller advertisement version: 2 Duplex: half Management address(es): ------------------------- Device ID: R7 Entry address(es): IP address: 180.40.7.131 Platform: cisco 2611XM, Capabilities: Router Switch --More--  Interface: FastEthernet0/7, Port ID (outgoing port): FastEthernet0/1 Holdtime : 147 sec Version : Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller advertisement version: 2 VTP Management Domain: '' Duplex: half Management address(es): ------------------------- Device ID: R4 Entry address(es): IP address: 180.40.7.130 Platform: cisco 3620, Capabilities: Router Interface: FastEthernet0/4, Port ID (outgoing port): FastEthernet0/0 Holdtime : 121 sec --More--   --More--  Version : --More--  Cisco Internetwork Operating System Software --More--  IOS (tm) 3600 Software (C3620-IK9O3S7-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) --More--  Technical Support: http://www.cisco.com/techsupport --More--  Copyright (c) 1986-2005 by cisco Systems, Inc. --More--  Compiled Thu 10-Nov-05 03:19 by evmiller --More--   --More--  advertisement version: 2 --More--   S6#sh cdp nei d ------------------------- Device ID: R2 Entry address(es): IP address: 20.10.1.1 Platform: cisco 2611XM, Capabilities: Router Switch Interface: FastEthernet0/2, Port ID (outgoing port): FastEthernet0/1 Holdtime : 142 sec Version : Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller advertisement version: 2 VTP Management Domain: '' Duplex: full Management address(es): ------------------------- Device ID: R1 --More--  Entry address(es): IP address: 20.10.2.2 Platform: cisco 2611, Capabilities: Router Interface: FastEthernet0/1, Port ID (outgoing port): Ethernet0/1 Holdtime : 121 sec Version : Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller advertisement version: 2 Duplex: half Management address(es): ------------------------- Device ID: R7 Entry address(es): IP address: 180.40.7.131 Platform: cisco 2611XM, Capabilities: Router Switch --More--  Interface: FastEthernet0/7, Port ID (outgoing port): FastEthernet0/1 Holdtime : 130 sec Version : Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller advertisement version: 2 VTP Management Domain: '' Duplex: half Management address(es): ------------------------- Device ID: R4 Entry address(es): IP address: 180.40.7.130 Platform: cisco 3620, Capabilities: Router Interface: FastEthernet0/4, Port ID (outgoing port): FastEthernet0/0 Holdtime : 104 sec --More--   Version : Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3620-IK9O3S7-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Thu 10-Nov-05 03:19 by evmiller advertisement version: 2 Duplex: full Management address(es): ------------------------- Device ID: S5 Entry address(es): IP address: 208.28.1.2 Platform: Cisco WS-C3550-24, Capabilities: Router Switch IGMP Interface: FastEthernet0/24, Port ID (outgoing port): FastEthernet0/24 Holdtime : 151 sec Version : Cisco IOS Software, C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(25)SED, RELEASE SOFTWARE (fc1) --More--   S6# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#cry ? ca Certification authority dynamic-map Specify a dynamic crypto map template identity Enter a crypto identity list ipsec Configure IPSEC policy isakmp Configure ISAKMP policy key Long term key operations keyring Key ring commands map Enter a crypto map mib Configure Crypto-related MIB Parameters xauth X-Auth parameters R4(config)#cry keu  ey ? generate Generate new keys pubkey-chain Peer public key chain management zeroize Remove keys R4(config)#cry key ge ? rsa Generate RSA keys R4(config)#cry key ge rsa ? general-keys Generate a general purpose RSA key pair for signing and encryption usage-keys Generate separate RSA key pairs for signing and encryption R4(config)#cry key ge rsa ge ? exportable Allow the key to be exported label Provide a label modulus Provide number of modulus bits on the command line R4(config)#cry key ge rsa ge The name for the keys will be: R4.cciestudent.com Choose the size of the key modulus in the range of 360 to 2048 for your General Purpose Keys. Choosing a key modulus greater than 512 may take a few minutes. How many bits in the modulus [512]: % Generating 512 bit RSA keys ...[OK] R4(config)# *Mar 2 00:34:54.473: %SSH-5-ENABLED: SSH 1.5 has been enabled R4(config)#cry key ge rsa ge ncry key ge rsa ge ocry key ge rsa ge  cry key ge rsa ge  % Use 'crypto key zeroize rsa' to delete signature keys. R4(config)#crypto key zeroize rsa % All RSA keys will be removed. % All router certs issued using these keys will also be removed. Do you really want to remove these keys? [yes/no]: y R4(config)# *Mar 2 00:35:15.793: %SSH-5-DISABLED: SSH 1.5 has been disabled R4(config)# R4(config)#^Z R4#sh ru *Mar 2 00:35:19.441: %SYS-5-CONFIG_I: Configured from console by console R4#sh run | b cry no service password-encryption ! hostname R4 ! boot-start-marker boot-end-marker ! ! no aaa new-model ip subnet-zero ! ! ip cef no ip domain lookup ! ip audit po max-events 100 ! ! ! ! ! ! ! --More--  ! ! ! ! ! ! ! class-map match-all dscp26 match dscp af31 class-map match-all dscp24 match dscp cs3 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 ! ! policy-map test class dscp24 class dscp26 class dscp28 class prec3 ! --More--   R4# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh runh  | b dhcp ip dhcp excluded-address 180.40.7.129 ip dhcp excluded-address 180.40.7.131 180.40.7.134 ! ip dhcp pool Prob15 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 domain-name cciestudent.com dns-server 208.28.1.82 option 150 ip 20.20.20.20 ! ip dhcp pool R4 host 180.40.7.130 255.255.255.224 client-identifier 0100.024b.cb56.e0 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! ! ! ! --More--   R3#^x4 % Unknown command or computer name, or unable to find computer address R3# R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#sh run int fa 0/0 Building configuration... Current configuration : 128 bytes ! interface FastEthernet0/0 ip address dhcp client-id FastEthernet0/0 duplex auto speed auto service-policy input test end R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES DHCP up up ATM1/0 unassigned YES unset administratively down down Loopback0 100.1.1.1 YES manual up up R4# R4# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip dhcp pool Prob13 R2(dhcp-config)# host 180.40.7.97 255.255.255.224 R2(dhcp-config)# client-identifier 0063.6973.636f.2d30.3031.332e.3830.6532.$dentifier 0063.6973.636f.2d30.3031.332e.3830.6532.2 e30.3238.0063.6973.636f.2d30.3031.332e.3830.6532.2e30.3238.3 02d.4661.636f.2d30.3031.332e.3830.6532.2e30.3238.302d.4661.3 02f.32 R2(dhcp-config)#^Z R2# *Mar 2 00:34:50.179: %SYS-5-CONFIG_I: Configured from console by console R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa 0/1 R2(config-if)#ip hel R2(config-if)#ip help R2(config-if)#ip helper-address 208.28.1.99 R2(config-if)#^Z R2# *Mar 2 00:35:42.833: %SYS-5-CONFIG_I: Configured from console by console R2# RACK14AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#conf     RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#confi gt ^ % Invalid input detected at '^' marker. R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#do sh run int fa 0/     s 1/0 Building configuration... Current configuration : 258 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression active connections 20 frame-relay map ip 180.40.7.67 302 broadcast end R3(config-if)#ip hel R3(config-if)#ip help R3(config-if)#ip helper-address 208.20 8.1.99 R3(config-if)#^Z R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 0 1/9  /0.2 R7(config-subif)#' ip help R7(config-subif)#ip helper-address 208.28.1.99 R7(config-subif)#do shr  run int s 1/0.2 Building configuration... Current configuration : 213 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay class Prob6 frame-relay interface-dlci 702 end R7(config-subif)#frame-relay interface-dlci 702 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R7(config-subif)#frame-relay interface-dlci 702 pro R7(config-subif)#frame-relay interface-dlci 702 protocol ? A.B.C.D Protocol specific address ip IP R7(config-subif)#frame-relay interface-dlci 702 protocol ip ? A.B.C.D Protocol specific address R7(config-subif)#frame-relay interface-dlci 702 protocol ip 180.40.7.162 ? R7(config-subif)#frame-relay interface-dlci 702 protocol ip 180.40.7.162   %Can't add another VC to point-to-point subinterface R7(config-fr-dlci)#no    exit R7(config-subif)#do sh % Type "show ?" for a list of subcommands R7(config-subif)#do sh exit frame-relay interface-dlci 702 protocol ip 180.40.7.162do sh run int s 1/0.2  Building configuration... Current configuration : 213 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay class Prob6 frame-relay interface-dlci 702 end R7(config-subif)#no frame-relay interface-dlci 702 R7(config-subif)#no frame-relay interface-dlci 702do sh run int s 1/0.2  *Mar 1 18:52:23.537: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-subif)#do sh run int s 1/0.2 exit frame-relay interface-dlci 702 protocol ip 180.40.7.162 R7(config-fr-dlci)#^Z R7# *Mar 1 18:52:28.517: %SYS-5-CONFIG_I: Configured from console by console R7# *Mar 1 18:52:48.935: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run | b dhcp ip dhcp pool Prob13 host 180.40.7.97 255.255.255.224 client-identifier 0063.6973.636f.2d30.3031.332e.3830.6532.2e30.3238.302d.4661.302f.32 ! ip cef no ip domain lookup ip audit po max-events 100 frame-relay de-list 1 protocol ip list 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! --More--  ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto ! interface Serial1/0 --More--   R2# R2# R2# R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] * R3#sh run int s 1/0 Building configuration... Current configuration : 289 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 ip helper-address 208.28.1.99 encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression active connections 20 frame-relay map ip 180.40.7.67 302 broadcast end R3# R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int s 1/0.2 Building configuration... Current configuration : 235 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay class Prob6 frame-relay interface-dlci 702 protocol ip 180.40.7.162 end R7# R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#gl R7(config-if)#glbp ? <0-1023> Group number R7(config-if)#glbp 47 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 47 pri R7(config-if)#glbp 47 priority ? <1-255> Priority value R7(config-if)#glbp 47 priority 150 > ? R7(config-if)#glbp 47 priority 150 R7(config-if)#gl R7(config-if)#glbp 47 pri R7(config-if)#glbp 47 priority        e R7(config-if)#glbp 47 preempt ? delay Wait before preempting R7(config-if)#glbp 47 preempt R7(config-if)#do sh glbp FastEthernet0/1 - Group 47 State is Disabled Virtual IP address is unknown Hello time 3 sec, hold time 10 sec Redirect time 600 sec, forwarder time-out 14400 sec Preemption enabled, min delay 0 sec Active is unknown Standby is unknown Priority 150 (configured) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There are no forwarders R7(config-if)# R7(config-if)# R7(config-if)# R7(config-if)# R7(config-if)#do sh glbp gl R7(config-if)#glbp 47 wi R7(config-if)#glbp 47 wi eu i R7(config-if)#glbp 47 weighting ? <1-254> Weighting maximum value track Interface tracking R7(config-if)#glbp 47 weighting 100 ? lower Weighting lower threshold upper Weighting upper threshold R7(config-if)#glbp 47 weighting 100 lo R7(config-if)#glbp 47 weighting 100 lower 75 ? upper Weighting upper threshold R7(config-if)#glbp 47 weighting 100 lower 75 up R7(config-if)#glbp 47 weighting 100 lower 75 upper ? <75-100> Weighting upper threshold value R7(config-if)#glbp 47 weighting 100 lower 75 upper 100 R7(config-if)#exit R7(config)#track 1 ? interface Select an interface to track ip IP protocol R7(config)#track 1 ip ? route IP route R7(config)#track 1 ip route ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R7(config)#track 1 ip route 1 20.10.1.0  /24 ? metric Route metric reachability Route reachability state R7(config)#track 1 ip route 20.10.1.0/24 re R7(config)#track 1 ip route 20.10.1.0/24 reachability R7(config-track)#exit R7(config)#int fa 0/0 1 R7(config-if)#int fa 0/1 do sh run int fa 0/0 1 Building configuration... Current configuration : 272 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 47 ip 180.40.7.133 glbp 47 priority 150 glbp 47 preempt glbp 47 weighting 100 lower 75 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 end R7(config-if)#gl R7(config-if)#glbp 1 47 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 47 wei R7(config-if)#glbp 47 weighting tr R7(config-if)#glbp 47 weighting track ? <1-500> Tracked object R7(config-if)#glbp 47 weighting track 1 ? decrement Weighting decrement R7(config-if)#glbp 47 weighting track 1 dec R7(config-if)#glbp 47 weighting track 1 decrement ? <1-255> Decrement value R7(config-if)#glbp 47 weighting track 1 decrement 50 ? R7(config-if)#glbp 47 weighting track 1 decrement 50 R7(config-if)#gl R7(config-if)#glbp 47 ip ? A.B.C.D Virtual IP address R7(config-if)#glbp 47 ip 180.40.7.134 ? secondary Make this IP address a secondary address R7(config-if)#glbp 47 ip 180.40.7.134 R7(config-if)#^Z R7# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int f 0/0 R3(config-if)#glbp 47 track 3 ? % Unrecognized command R3(config-if)#glbp 47 track 3         wei R3(config-if)#glbp 47 weighting tra R3(config-if)#glbp 47 weighting track 3 ? decrement Weighting decrement R3(config-if)#glbp 47 weighting track 3 dec 50 R3(config-if)#gl R3(config-if)#glbp 47 wir e  ei R3(config-if)#glbp 47 weighting ? <1-254> Weighting maximum value track Interface tracking R3(config-if)#glbp 47 weighting 100 lo 75 l up 100 R3(config-if)#gl 47 ip 180 ; .  .40.7.12 34 R3(config-if)#^Z R3# *Mar 2 00:56:01.939: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 2 00:56:08.730: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 47 Fwd 2 state Listen -> Active R3# R3# R3#sh glbp FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:00:06 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.195 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 150 (expires in 7.636 sec) Standby is local Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 3 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0013.60e3.f021 Time to live: 14397.632 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.632 sec) Forwarder 2 --More--   State is Active 1 state change, last state change 00:01:11 MAC address is 0007.b400.2f02 (default) Owner ID is 0013.7f15.f280 Preemption enabled, min delay 30 sec Active is local, weighting 100 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/1 0 R3(config-if)#int fa 0/0gl 47 ip 180.40.7.134bp 47 weighting 100 lo 75 up 100track 3 dec 50         ? <1-500> Tracked object R3(config-if)#glbp 47 weighting track 1 ? decrement Weighting decrement R3(config-if)#glbp 47 weighting track 1 DEC 50 R3(config-if)#^Z R3#sh *Mar 2 01:06:05.421: %SYS-5-CONFIG_I: Configured from console by console R3#sh track Track 1 (via HSRP) Interface Serial1/2 line-protocol Line protocol is Up 3 changes, last change 01:07:07 Tracked by: HSRP FastEthernet0/0 47 GLBP FastEthernet0/0 47 Track 2 (via HSRP) Interface Serial1/0 line-protocol Line protocol is Up 1 change, last change 01:16:23 Tracked by: HSRP FastEthernet0/0 47 Track 3 IP route 20.10.2.0 255.255.255.0 reachability Reachability is Up (OSPF) 3 changes, last change 01:04:43 First-hop interface is Serial1/2 Tracked by: HSRP FastEthernet0/0 47 GLBP FastEthernet0/0 47 R3#sh glb FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:09:58 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.369 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 150 (expires in 9.811 sec) Standby is local Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 1 state Up decrement 50 Track object 3 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0013.60e3.f021 Time to live: 14399.807 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.807 sec) --More--   R3# RACK14AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#shut R2(config-if)# *Mar 2 01:06:43.739: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-if)# RACK14AS>3 [Resuming connection 3 to r3 ... ] *M R3# *Mar 2 01:06:46.268: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 01:06:47.269: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3# R3# R3# R3# R3# R3#sh glbp FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:10:42 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.299 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 150 (expires in 7.740 sec) Standby is local Priority 100 (default) Weighting 50, low (configured 100), thresholds: lower 75, upper 100 Track object 1 state Down decrement 50 Track object 3 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0013.60e3.f021 Time to live: 14397.736 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.732 sec) --More--   Forwarder 2 State is Listen 2 state changes, last state change 00:00:01 MAC address is 0007.b400.2f02 (default) Owner ID is 0013.7f15.f280 Preemption enabled, min delay 30 sec Active is 180.40.7.131 (secondary), weighting 100 (expires in 9.988 sec) R3# *Mar 2 01:07:15.940: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 47 Fwd 2 state Active -> Listen R3# R3# R3# RACK14AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh glbp FastEthernet0/1 - Group 47 State is Active 2 state changes, last state change 00:12:34 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.393 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption enabled, min delay 0 sec Active is local Standby is 180.40.7.129, priority 100 (expires in 9.948 sec) Priority 150 (configured) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 1 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (2 active) Forwarder 1 State is Active 1 state change, last state change 00:12:24 MAC address is 0007.b400.2f01 (default) Owner ID is 0013.60e3.f021 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 --More--   Forwarder 2 State is Active 1 state change, last state change 00:00:20 MAC address is 0007.b400.2f02 (learnt) Owner ID is 0013.7f15.f280 Redirection enabled, 579.394 sec remaining (maximum 600 sec) Time to live: 14379.394 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is local, weighting 100 R7# RACK14AS>3 [Resuming connection 3 to r3 ... ] R3# RACK14AS>2 [Resuming connection 2 to r2 ... ] *Ma R2(config-if)#no shut R2(config-if)#^Z R2# *Mar 2 01:08:30.178: %SYS-5-CONFIG_I: Configured from console by console R2# *Mar 2 01:08:31.757: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 2 01:08:32.758: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R2# *Mar 2 01:08:41.897: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from LOADING to FULL, Loading Done R2# RACK14AS>3 [Resuming connection 3 to r3 ... ] *Mar 2 01: R3#sh glbp FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:12:37 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.382 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 150 (expires in 9.824 sec) Standby is local Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 1 state Up decrement 50 Track object 3 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0013.60e3.f021 Time to live: 14399.820 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.820 sec) --More--   Forwarder 2 State is Listen 2 state changes, last state change 00:01:38 MAC address is 0007.b400.2f02 (default) Owner ID is 0013.7f15.f280 Preemption enabled, min delay 30 sec (10 secs remaining) Active is 180.40.7.131 (secondary), weighting 100 (expires in 8.798 sec) R3# *Mar 2 01:09:05.416: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 47 Fwd 2 state Listen -> Active R3#sh glbp FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:13:03 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.952 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 150 (expires in 8.393 sec) Standby is local Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 1 state Up decrement 50 Track object 3 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0013.60e3.f021 Time to live: 14398.389 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.389 sec) --More--   Forwarder 2 State is Active 3 state changes, last state change 00:00:14 MAC address is 0007.b400.2f02 (default) Owner ID is 0013.7f15.f280 Preemption enabled, min delay 30 sec Active is local, weighting 100 R3#sh run | b track track 3 ip route 20.10.2.0 255.255.255.0 reachability ! ! ! class-map match-all dscp26 match dscp af31 class-map match-all dscp14 match ip dscp af13 class-map match-all dscp24 match dscp cs3 class-map match-all telnet match protocol telnet class-map match-all dscp12 match ip dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match access-group 105 ! ! policy-map test --More--   class dscp24 class dscp26 class dscp28 class prec3 class dscp14 class dscp12 policy-map Prob7 class telnet bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 policy-map Prob11 class dscp12 priority percent 25 ! ! ! ! ! ! interface FastEthernet0/0 --More--   ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 47 ip 180.40.7.133 vrrp 47 priority 150 glbp 47 ip 180.40.7.134 glbp 47 weighting 100 lower 75 glbp 47 weighting track 1 decrement 50 glbp 47 weighting track 3 decrement 50 standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/2 51 standby 47 track Serial1/0 51 standby 47 track 3 decrement 51 service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 --More--   R3# RACK14AS>4 [Resuming connection 4 to r4 ... ] R4#poi sh ip int brierun int fa 0/0ip int brie po ping 180.40.7.132 ^ % Invalid input detected at '^' marker. R4#poping 180.40.7.132poping 180.40.7.132 ing 180.40.7.132  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.132, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 4/4/4 ms R4#ping 180.40.7.132 3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.133, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 4/4/4 ms R4#ping 180.40.7.133 4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.134, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 4/4/4 ms R4#sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 40 0013.60e3.f021 ARPA FastEthernet0/0 Internet 180.40.7.130 - 0002.4bcb.56e0 ARPA FastEthernet0/0 Internet 180.40.7.129 40 0013.7f15.f280 ARPA FastEthernet0/0 Internet 180.40.7.134 0 0007.b400.2f01 ARPA FastEthernet0/0 Internet 180.40.7.133 0 0000.5e00.012f ARPA FastEthernet0/0 Internet 180.40.7.132 0 0000.0c07.ac2f ARPA FastEthernet0/0 R4# RACK14AS>7 [Resuming connection 7 to r7 ... ] * R7#sh run | b track track 1 ip route 20.10.1.0 255.255.255.0 reachability ! ! ! class-map match-all S5Other match access-group 1 class-map match-all S5Telnet match access-group 1 match protocol telnet class-map match-any JPG match protocol http mime "*jpeg" match protocol http url "*jpg" match protocol http url "*jpe" match protocol http url "*jpeg" ! ! policy-map Prob5 class S5Telnet bandwidth 1000 class JPG shape average 1000000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 --More--  ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 47 ip 180.40.7.133 glbp 47 ip 180.40.7.134 glbp 47 priority 150 glbp 47 preempt --More--   glbp 47 weighting 100 lower 75 glbp 47 weighting track 1 decrement 50 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint --More--   R7# RACK14AS>6 [Resuming connection 6 to r6 ... ] S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int vlan 10 S6(config-if)#ip address 1d01h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up S6(config-if)#ip address          ip dhcp    add hdc   dcp h  h S6(config-if)#ip add dhcp S6(config-if)#^Z S6# 1d01h: %SYS-5-CONFIG_I: Configured from console by console S6# S6# S6#Interface Vlan10 assigned DHCP address 180.40.7.137, mask 255.255.255.224 sh ip       ping 180.40.7.134 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.134, timeout is 2 seconds: 1d01h: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Vlan10 from LOADING to FULL, Loading Done 1d01h: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on Vlan10 from LOADING to FULL, Loading Done.!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/4 ms S6#sh ip    arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.137 - 0013.80e2.0280 ARPA Vlan10 Internet 180.40.7.131 0 0013.60e3.f021 ARPA Vlan10 Internet 180.40.7.130 0 0002.4bcb.56e0 ARPA Vlan10 Internet 180.40.7.129 0 0013.7f15.f280 ARPA Vlan10 Internet 180.40.7.134 0 0007.b400.2f02 ARPA Vlan10 Internet 20.10.2.1 - 0013.80e2.0280 ARPA FastEthernet0/1 Internet 20.10.1.2 - 0013.80e2.0280 ARPA FastEthernet0/2 Internet 20.10.2.2 71 000a.8af0.d901 ARPA FastEthernet0/1 Internet 20.10.1.1 77 0013.7f15.f2e1 ARPA FastEthernet0/2 S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int vlan 10 S6(config-if)#shut S6(config-if)# 1d01h: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Vlan10 from FULL to DOWN, Neighbor Down: Interface down or detached 1d01h: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on Vlan10 from 2WAY to DOWN, Neighbor Down: Interface down or detached 1d01h: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on Vlan10 from FULL to DOWN, Neighbor Down: Interface down or detached S6(config-if)#^Z S6# 1d01h: %SYS-5-CONFIG_I: Configured from console by console 1d01h: %LINK-5-CHANGED: Interface Vlan10, changed state to administratively down S6# 1d01h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to down S6# RACK14AS>5 [Resuming connection 5 to r5 ... ]