=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.11.30 15:54:11 =~=~=~=~=~=~=~=~=~=~=~= RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh ver Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 09-Nov-05 19:23 by evmiller Image text-base: 0x80008098, data-base: 0x81A2C184 ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1) ROM: C2600 Software (C2600-J1S3-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) R1 uptime is 4 minutes System returned to ROM by power-on System image file is "flash:c2600-j1s3-mz.123-16a.bin" cisco 2611 (MPC860) processor (revision 0x202) with 59392K/6144K bytes of memory. Processor board ID JAB03110HF1 (459011416) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. TN3270 Emulation software. 2 Ethernet/IEEE 802.3 interface(s) --More--   R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv R1(config)#ipv6 u R1(config)#ipv6 unicast-routing R1(config)#int e 0/.1 ^ % Invalid input detected at '^' marker. R1(config)#int e 0/.1  1 R1(config-if)#ipv add 2005:0:104::1  /64 R1(config-if)#ipv add 2005:0:104::1/64                fe9 80::1 li R1(config-if)#ipv add fe80::1 link-local R1(config-if)#int s 0/1 R1(config-if)#int s 0/1pv add fe80::1 link-local 2005:0:104::1/64 4::1/64 ::1/64 ::1/64 2::1/640::1/641::1/64::1/64 ::1/64 ::1/64 1::1/640::1/642::1/64 R1(config-if)#ipv add 2005:0:102::1/64nt s 0/1 pv add fe80::1 link-local R1(config-if)# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset up up ATM1/0 192.10.32.9 YES manual up up R4#conf t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#default int atm 1/0 Building configuration... default ! ^ % Invalid input detected at '^' marker. default protocol ip 192.10.32.254 broadcast ^ % Invalid input detected at '^' marker. Interface ATM1/0 set to default configuration R4(config)#int atm 1/0 R4(config-if)#shut R4(config-if)#int lo 0 R4(config-if)# *Mar 1 00:07:44.911: %LINK-5-CHANGED: Interface ATM1/0, changed state to administratively down *Mar 1 00:07:45.911: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down R4(config-if)#ip  v add 2000:4:4::/64 R4(config-if)#e int fa 0/0 R4(config-if)#ipv add 2005:0:104::4/64 R4(config-if)#ipv add fe80::4 lin R4(config-if)#exit R4(config)#ipv un R4(config)#ipv unicast-routing R4(config)#^Z R4# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipb v R2(config)#ipv6 i R2(config)#ipv6 icmp        u R2(config)#ipv6 unicast-routing R2(config)#int s 1/1 R2(config-if)#ipv add 2005:0:102::2  /5 64 R2(config-if)#ipv add fe80::2 li R2(config-if)#ipv add fe80::2 link-local R2(config-if)#ipv add fe80::2 link-local 2005:0:102::2/64 nt s 1/1  2 R2(config-if)#int s 1/2pv add fe80::2 link-local 2005:0:102::2/64 ::2/64 ::2/64 2::2/640::2/643::2/64 R2(config-if)#ipv add 2005:0:1203::2/64nt s 1/2 pv add fe80::2 link-local R2(config-if)#int s 1/0.1 R2(config-subif)#int s 1/0.1pv add fe80::2 link-local 2005:0:1203::2/64 ::2/64 ::2/64 ::2/64 ::2/64 2::2/643::2/647::2/64 R2(config-subif)#ipv add 2005:0:237::2/64nt s 1/0.1 pv add fe80::2 link-local R2(config-subif)#ipv add fe80::2 link-local 2005:0:237::2/64 nt s 1/0.1  2 R2(config-subif)#int s 1/0.2pv add fe80::2 link-local 2005:0:237::2/64 ::2/64 ::2/64 7::2/640::2/64::2/64 ::2/64 ::2/64 7::2/640::2/642::2/64 R2(config-subif)#ipv add 2005:0:702::2/64nt s 1/0.2 pv add fe80::2 link-local R2(config-subif)#^Z R2# *Mar 1 00:07:21.186: %SYS-5-CONFIG_I: Configured from console by console R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ipbv  v u R3(config)#ipv unicast-routing R3(config)#int s 1/2 R3(config-if)#ipv add 2005:0:1203::3/64 R3(config-if)#ipv add lin R3(config-if)#ipv add lin   fe80::3 li R3(config-if)#ipv add fe80::3 link-local R3(config-if)#int s 1/0 R3(config-if)#~~int s 1/0pv add fe80::3 link-local 2005:0:1203::3/64 3::3/64 ::3/64 ::3/64 ::3/64 2::3/643::3/647::3/64 R3(config-if)#ipv add 2005:0:237::3/64nt s 1/0 pv add fe80::3 link-local R3(config-if)#int lo 0 R3(config-if)#ipv add 2000:3:3::/64 R3(config-if)# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv u R7(config)#ipv unicast-routing R7(config)#int s 1/0.1 R7(config-subif)#ipv add 2005:0:237::7  /64 R7(config-subif)#ipv u add fe80:: li R7(config-subif)#ipv add fe80:: link-local R7(config-subif)#ipv add fe80:: link-local 2005:0:237::7/64 nt s 1/0.1  2 R7(config-subif)#int s 1/0.2pv add fe80:: link-local 2005:0:237::7/64 ::7/64 ::7/64 ::7/64 7::7/640::7/642::7/64 R7(config-subif)#ipv add 2005:0:702::7/64nt s 1/0.2 pv add fe80:: link-local R7(config-subif)#^Z R7# *Mar 1 00:08:50.208: %SYS-5-CONFIG_I: Configured from console by console R7#ping 2005:0:702::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R7# R7# R7# R7#ping 2005:0:702::2 rep R7#ping 2005:0:702::2 repeat 100 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R7#ping Protocol [ip]: Target IP address:  % Bad IP address R7# R7# R7#ping Protocol [ip]: 1 ipv6 Target IPv6 address: 2005:0:702::2 Repeat count [5]: 100 Datagram size [100]: Timeout in seconds [2]: Extended commands? [no]: Type escape sequence to abort. Sending 100, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Success rate is 100 percent (100/100), round-trip min/avg/max = 56/57/61 ms R7#100 1002005:0:702::2ipv6 ping   2005:0:702::2 repeat 100i2005:0:702::2 repeat 100p2005:0:702::2 repeat 100v2005:0:702::2 repeat 10062005:0:702::2 repeat 100 2005:0:702::2 repeat 100 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R7#ping fe80::0:  2 Output Interface: serial1/0.1 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R7#serial1/0.2ping fe80::2 Output Interface: s1/0.2 % Bad interface R7#pin g    g 2005:0:237::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: ... RACK9AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh run int s 1/0 Building configuration... Current configuration : 133 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local end R3(config-if)#int s 1/0 R3(config-if)#fram map ipv 2005:0:237::2 302 br R3(config-if)#fram map ipv 2005:0:237::2 302 broadcast R3(config-if)#fram map ipv 2005:0:237::2 302 broadcast  broadcast 7 broadcast  307 broadcast 7 307 broadcast  R3(config-if)# RACK9AS>7 [Resuming connection 7 to r7 ... ] .. R7#ping 2005:0:237::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R7#ping 2005:0:237::3 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 164/165/169 ms R7# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#ping 2005:0:1203::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms R2#ping 2005:0P:  :102::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/36 ms R2# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#ping fe80::3 Output Interface: serial1/0.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::3, timeout is 2 seconds: ... Success rate is 0 percent (0/3) R7#[Aserial1/0.2ping fe80::3 Output Interface: ping fe80::3serial1/0.2  1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::3, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#fram map ipv fe80::7 307 br R3(config-if)#^Z R3# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 00:13:58.922: %SYS-5-CONFIG_I: Configured from console by console R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#serial1/0.1ping fe80::3 Output Interface: ping fe80::3serial1/0.1  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::3, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/0 Building configuration... Current configuration : 277 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast end R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#deb fram pack Frame Relay packet debugging is on R7#deb fram packserial1/0.1 ping fe80::3 Output Interface: ping fe80::3deb fram packserial1/0.1  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::3, timeout is 2 seconds: *Mar 1 00:14:41.287: Serial1/0.1(o): dlci 703(0xACF1), pkt type 0x86DD(IPV6), datagramsize 104. *Mar 1 00:14:43.287: Serial1/0.1(o): dlci 703(0xACF1), pkt type 0x86DD(IPV6), datagramsize 104 *Mar 1 00:14:43.631: Serial1/0(i): dlci 702(0xACE1), pkt type 0x2000, datagramsize 412. *Mar 1 00:14:45.290: Serial1/0.1(o): dlci 703(0xACF1), pkt type 0x86DD(IPV6), datagramsize 104. *Mar 1 00:14:47.293: Serial1/0.1(o): dlci 703(0xACF1), pkt type 0x86DD(IPV6), datagramsize 104. *Mar 1 00:14:49.296: Serial1/0.1(o): dlci 703(0xACF1), pkt type 0x86DD(IPV6), datagramsize 104 *Mar 1 00:14:50.206: Serial1/0.1: Broadcast on DLCI 703 link 65(CDP) *Mar 1 00:14:50.206: Serial1/0.1(o): dlci 703(0xACF1), pkt type 0x2000(CDP), datagramsize 412 *Mar 1 00:14:50.206: Serial1/0.2: Broadcast on DLCI 702 link 65(CDP) *Mar 1 00:14:50.206: Serial1/0.2(o): dlci 702(0xACE1), pkt type 0x2000(CDP), datagramsize 412 *Mar 1 00:14:50.242: broadcast dequeue *Mar 1 00:14:50.242: Serial1/0.1(o):Pkt sent on dlci 703(0xACF1), pkt type 0x2000(CDP), datagramsize 412 *Mar 1 00:14:50.242: broadcast dequeue. Success rate is 0 percent (0/5) R7# *Mar 1 00:14:50.242: Serial1/0.2(o):Pkt sent on dlci 702(0xACE1), pkt type 0x2000(CDP), datagramsize 412 R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#deb fram pack Frame Relay packet debugging is on R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] serial1/0.1 u all All possible debugging has been turned off R7#u allserial1/0.1ping fe80::3 Output Interface: ping fe80::3u all serial1/0.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::3, timeout is 2 seconds: RACK9AS>37 [Resuming connection 7 to r7 ... ] ... RACK9AS>3 [Resuming connection 3 to r3 ... ] *Ma R3# *Mar 1 00:15:20.335: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 104 *Mar 1 00:15:20.339: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3# *Mar 1 00:15:22.339: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 104 *Mar 1 00:15:22.343: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3#u all All possible debugging has been turned off R3#sh run   int s 1/0 Building configuration... Current configuration : 277 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast end R3#deb ipv icmp R3#deb ipv icmp ? R3#deb ipv icmp ICMP packet debugging is on R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] ..serial1/0.1ping fe80::3 Output Interface: ping fe80::3serial1/0.1  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::3, timeout is 2 seconds: RACK9AS>3 [Resuming connection 3 to r3 ... ] *M R3# *Mar 1 00:16:02.176: ICMPv6: Received ICMPv6 packet from FE80::, type 128 *Mar 1 00:16:02.180: ICMPv6: Received echo request from FE80:: *Mar 1 00:16:02.180: ICMPv6: Sending echo reply to FE80:: R3# *Mar 1 00:16:04.179: ICMPv6: Received ICMPv6 packet from FE80::, type 128 *Mar 1 00:16:04.179: ICMPv6: Received echo request from FE80:: *Mar 1 00:16:04.183: ICMPv6: Sending echo reply to FE80:: R3# *Mar 1 00:16:06.178: ICMPv6: Received ICMPv6 packet from FE80::, type 128 *Mar 1 00:16:06.178: ICMPv6: Received echo request from FE80:: *Mar 1 00:16:06.182: ICMPv6: Sending echo reply to FE80:: R3# *Mar 1 00:16:08.182: ICMPv6: Received ICMPv6 packet from FE80::, type 128 *Mar 1 00:16:08.182: ICMPv6: Received echo request from FE80:: *Mar 1 00:16:08.186: ICMPv6: Sending echo reply to FE80:: R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] .. R7#sh run int s 1/0.1 Building configuration... Current configuration : 142 bytes ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80:: link-local frame-relay interface-dlci 703 end R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0.1 R7(config-subif)# ipv6 address FE80::7 li R7(config-subif)#do sh run int s 1/0.2 Building configuration... Current configuration : 142 bytes ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::7/64 ipv6 address FE80:: link-local frame-relay interface-dlci 702 end R7(config-subif)#do sh run int s 1/0.2 ipv6 address FE80::7 liint s 1/0.1  2 R7(config-subif)#int s 1/0.2do sh run int s 1/0.2 ipv6 address FE80::7 li R7(config-subif)#^Z R7#confi tsh run int s 1/0.1 *Mar 1 00:16:54.458: %SYS-5-CONFIG_I: Configured from console by console R7#sh run int s 1/0.1erial1/0.1 ping fe80::3 Output Interface: ping fe80::3confi t sh run int s 1/0.1erial1/0.1  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 ms R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#u all All possible debugging has been turned off R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)#^Z R1#ping *Mar 1 00:18:31.665: %SYS-5-CONFIG_I: Configured from console by console R1#ping 2005:0:104::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/8 ms R1#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Ethernet0/0 ip address 180.40.7.66 255.255.255.224 half-duplex ! interface Serial0/0 no ip address shutdown --More--  ! interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::1/64 ipv6 address FE80::1 link-local ! interface Serial0/1 no ip address ipv6 address 2005:0:102::1/64 ipv6 address FE80::1 link-local clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! ip http server ip classless ! ! ! --More-- RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b ipv     1/0 interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::2/64 ipv6 address FE80::2 link-local frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::2/64 ipv6 address FE80::2 link-local frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ipv6 address FE80::2 link-local ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 address FE80::2 link-local --More--   clock rate 64000 --More--  ! --More-- RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b Lo interface Loopback0 no ip address ipv6 address 2000:3:3::/64 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 --More--   ipv6 address FE80::3 link-local frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::3/64 ipv6 address FE80::3 link-local ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 --More-- RACK9AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#sh run | b Lo interface Loopback0 no ip address ipv6 address 2000:4:4::/64 ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2005:0:104::4/64 ipv6 address FE80::4 link-local ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! ip http server no ip http secure-server ip classless ! ! ! ! --More--   R4# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b 1/0.1 interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80::7 link-local frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::7/64 ipv6 address FE80::7 link-local frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 --More--   no ip address --More--   shutdown --More--  ! --More--  interface Serial1/5 --More--   no ip address --More--   R7# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#confit  t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#int lo 0 R4(config-if)#ipv rip > ? WORD User selected string identifying this RIP process R4(config-if)#ipv rip R4Rip en R4(config-if)#int e   fa 0/0 R4(config-if)#int fa 0/0pv rip R4Rip en R4(config-if)#^Z R4# RACK9AS>1 [Resuming connection 1 to r1 ... ]  ! --More--   R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ipv rip R1Rip en R1(config-if)#int s 1/0   0/. 1 R1(config-if)#int s 0/1pv rip R1Rip en R1(config-if)#^Z R1# RACK9AS>2 [Resuming connection 2 to r2 ... ]  interface Serial1/3 --More--   R2#q\  conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#int s 1/1 R2(config-if)#ipv rip R2Rip en R2(config-if)#^Z R2# *Mar 1 00:21:47.630: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b router ipv6 router rip R2Rip ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R2#qsh ipv route ^ % Invalid input detected at '^' marker. R2#qsh ipv routeqssh ipv route  IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::1, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   R2#ping 2000:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/41/48 ms R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh run I | 0/1 ^ % Invalid input detected at '^' marker. R1#sh run | 0/1b0/1 0/1 interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::1/64 ipv6 address FE80::1 link-local ipv6 rip R1Rip enable ! interface Serial0/1 no ip address ipv6 address 2005:0:102::1/64 ipv6 address FE80::1 link-local ipv6 rip R1Rip enable clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! ip http server ip classless ! ! --More--   R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b     int s 1/11~ ^ % Invalid input detected at '^' marker. R2#sh run int s 1/11~   Building configuration... Current configuration : 129 bytes ! interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ipv6 address FE80::2 link-local ipv6 rip R2Rip enable end R2# RACK9AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh run | b Lo interface Loopback0 no ip address ipv6 address 2000:4:4::/64 ipv6 rip R4Rip enable ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2005:0:104::4/64 ipv6 address FE80::4 link-local ipv6 rip R4Rip enable ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! ip http server no ip http secure-server ip classless ! ! --More--  ipv6 router rip R4Rip --More--  ! --More--  ! --More--   R4# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#ipv    pv ? access-list Configure access lists cef Cisco Express Forwarding for IPv6 hop-limit Configure hop count limit host Configure static hostnames icmp Configure ICMP parameters local Specify local options nat NAT-PT Configuration commands neighbor Neighbor prefix-list Build a prefix list route Configure static routes router Enable an IPV6 routing process source-route Process packets with source routing header options unicast-routing Enable unicast routing R1(config)#ipv router rip R1Rip R1(config-rtr)#distr R1(config-rtr)#distribute-list ? prefix-list Filter connections based on an IPv6 prefix-list R1(config-rtr)#distribute-list                 exit R1(config)#ipv R1(config)#ipv6 pre R1(config)#ipv6 prefix-list ? WORD Name of a prefix list sequence-number Include/exclude sequence numbers in NVGEN R1(config)#ipv6 prefix-list P NoR4Loop ? deny Specify packets to reject description Prefix-list specific description permit Specify packets to forward seq sequence number of an entry R1(config)#ipv6 prefix-list NoR4Loop den 2000:4:4::/64 R1(config)#IPV   ipv6 prefix-list NoR4Loop den 2000:4:4::/64                 per ::/0 ? ge Minimum prefix length to be matched le Maximum prefix length to be matched R1(config)#ipv6 prefix-list NoR4Loop per ::/0 ge ? <0-128> Minimum prefix length R1(config)#ipv6 prefix-list NoR4Loop per ::/0 ge 0 R1(config)#do sh run | i ipv6 Pre R1(config)#do sh run | i ipv6 Prere pre ipv6 prefix-list NoR4Loop seq 5 deny 2000:4:4::/64 ipv6 prefix-list NoR4Loop seq 10 permit ::/0 R1(config)#no ipv6 prefix-list NoR4Loop seq 10 % Incomplete command. R1(config)#no ipv6 prefix-list NoR4Loop seq 10                                  ipv6 prefix-list NoR4Loop seq 10 permit ::/0 R1(config)# R1(config)#no ipv6 prefix-list NoR4Loop seq 10 permit ::/0 do sh run | i ipv6 pre Preipv6 prefix-list NoR4Loop per ::/0 ge 0      le 128 R1(config)#ipv router rip R1Rip R1(config-rtr)#distr R1(config-rtr)#distribute-list p R1(config-rtr)#distribute-list prefix-list ? WORD Prefix-list name R1(config-rtr)#distribute-list prefix-list NoR4Loop ? in out R1(config-rtr)#distribute-list prefix-list NoR4Loop out ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface Ethernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R1(config-rtr)#distribute-list prefix-list NoR4Loop out ser 0/1 R1(config-rtr)#^Z R1# *Mar 1 00:27:56.864: %SYS-5-CONFIG_I: Configured from console by console R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh ipv route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::1, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   R2#clea ipv rout * R2#clea ipv rout *sh ipv route  IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::1, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   R2#sh ipv rip data RIP process "R2Rip", local RIB 2000:4:4::/64, metric 3, installed Serial1/1/FE80::1, expires in 117 secs 2005:0:102::/64, metric 2 Serial1/1/FE80::1, expires in 172 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::1, expires in 172 secs R2#s clea ipv rip ? WORD IPv6 RIP process name R2#clea ipv rip R2#clea ipv rip sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB 2005:0:102::/64, metric 2 Serial1/1/FE80::1, expires in 179 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::1, expires in 179 secs R2#sh ipv route IPv6 Routing Table - 11 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] --More--   via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh ru |  b n | b router      rotu  uter router rip version 2 network 180.40.0.0 no auto-summary ! ip http server ip classless ! ! ipv6 router rip R1Rip distribute-list prefix-list NoR4Loop out Serial0/1 ! ! ! ipv6 prefix-list NoR4Loop seq 5 deny 2000:4:4::/64 ipv6 prefix-list NoR4Loop seq 10 permit ::/0 le 128 ! ! ! ! ! line con 0 exec-timeout 0 0 --More--   R1# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#ipv ospf ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R2(config-if)#ipv ospf 1 ? area Set the OSPF area ID R2(config-if)#ipv ospf 1 area 20 R2(config-if)# *Mar 1 00:30:30.075: %OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id, please configure manually R2(config-if)# R2(config-if)# R2(config-if)# R2(config-if)#exit R2(config)#ipv router ospf 1 R2(config-rtr)#rotu R2(config-rtr)#rotut   ut R2(config-rtr)#router-id 2.2.2.2 R2(config-rtr)#do sh run int s 1/2 Building configuration... Current configuration : 146 bytes ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 20 clock rate 64000 end R2(config-rtr)#^Z R2# RACK9AS>3 [Resuming connection 3 to r3 ... ]   no ip address --More--   R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ipv router ospf 1 R3(config-rtr)# *Mar 1 00:31:08.642: %OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id, please configure manually R3(config-rtr)# R3(config-rtr)# R3(config-rtr)#route R3(config-rtr)#router-id 3.3.3.3 R3(config-rtr)#int s/ 1/2 R3(config-if)#ipv ospf 1 area 20 R3(config-if)#int lo 0 R3(config-if)#int lo 0pv ospf 1 area 20  51 R3(config-if)# *Mar 1 00:31:31.583: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/2 from LOADING to FULL, Loading Done R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# RACK9AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh ipv route IPv6 Routing Table - 11 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] --More--   via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipv router ospf 1 R2(config-rtr)#area 20 ? default-cost Set the summary default-cost of a NSSA/stub area nssa Specify a NSSA area range Summarize routes matching address/mask (border routers only) stub Specify a stub area virtual-link Define a virtual link and its parameters R2(config-rtr)#area 20 vi R2(config-rtr)#area 20 virtual-link ? A.B.C.D RouterID associated with virtual link neighbor R2(config-rtr)#area 20 virtual-link 3.3.3.3 ? dead-interval Dead router detection time hello-interval Hello packet interval retransmit-interval LSA retransmit interval transmit-delay LSA transmission delay R2(config-rtr)#area 20 virtual-link 3.3.3.3 R2(config-rtr)#^Z R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#ipv router ospf 1 R3(config-rtr)#area 20 vir R3(config-rtr)#area 20 virtual-link 2.2.2.2 R3(config-rtr)#^Z R3# *Mar 1 00:32:49.267: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# R3# R3#sh ip  v ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 INIT/ - 00:00:34 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:34 11 Serial1/2 R3# *Mar 1 00:32:58.879: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on OSPF_VL0 from LOADING to FULL, Loading Done R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:29 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:39 11 Serial1/2 R3#sh ipv ospa fi   pf int OSPF_VL0 is up, line protocol is up Interface ID 28 Area 0, Process ID 1, Instance ID 0, Router ID 3.3.3.3 Network Type VIRTUAL_LINK, Cost: 781 Configured as demand circuit. Run as demand circuit. DoNotAge LSA allowed. Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:09 Index 1/1/3, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 2.2.2.2 (Hello suppressed) Suppress hello for 1 neighbor(s) Serial1/2 is up, line protocol is up Link Local Address FE80::3, Interface ID 11 Area 20, Process ID 1, Instance ID 0, Router ID 3.3.3.3 Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 --More--   R3#sh ipv ospf vir Virtual Link OSPF_VL0 to router 2.2.2.2 is up Interface ID 28, IPv6 address 2005:0:1203::2 Run as demand circuit DoNotAge LSA allowed. Transit area 20, via interface Serial1/2, Cost of using 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Adjacency State FULL (Hello suppressed) Index 1/1/2, retransmission queue length 0, number of retransmission 1 First 0x0(0)/0x0(0)/0x0(0) Next 0x0(0)/0x0(0)/0x0(0) Last retransmission scan length is 1, maximum is 1 Last retransmission scan time is 0 msec, maximum is 0 msec R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh ipv route IPv6 Routing Table - 13 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] via ::, Serial1/2 O 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#p 2000:3:3:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms R2#sh run | b 1/2 interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 20 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! --More--  interface Serial1/7 no ip address shutdown ! ip classless ! ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes area 20 virtual-link 3.3.3.3 ! ipv6 router rip R2Rip ! ! ! ! ! ! ! ! --More-- RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b Lo interface Loopback0 no ip address ipv6 address 2000:3:3::/64 ipv6 ospf 1 area 51 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay --More--   ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::3/64 ipv6 address FE80::3 link-local ipv6 ospf 1 area 20 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown --More--  ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! ip classless ! ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 3.3.3.3 log-adjacency-changes area 20 virtual-link 2.2.2.2 ! --More-- RACK9AS>2 [Resuming connection 2 to r2 ... ]  ! --More--   R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#r ipv router ospf 1 R2(config-rtr)#redi R2(config-rtr)#redistribute rip R2Rip ? metric Metric for redistributed routes metric-type OSPF/IS-IS exterior metric type for redistributed routes route-map Route map reference tag Set tag for routes redistributed into OSPF R2(config-rtr)#redistribute rip R2Rip tag 2 ? metric Metric for redistributed routes metric-type OSPF/IS-IS exterior metric type for redistributed routes route-map Route map reference R2(config-rtr)#redistribute rip R2Rip tag 2 R2(config-rtr)#e ipv router rip R2Rip R2(config-rtr)#redis R2(config-rtr)#redistribute o R2(config-rtr)#redistribute ospf 1 ? match Redistribution of OSPF routes metric Metric for redistributed routes route-map Route map reference R2(config-rtr)#redistribute ospf 1 R2(config-rtr)#DEFA    defa R2(config-rtr)#default ? distance Administrative distance distribute-list Filter networks in routing updates maximum-paths Forward packets over multiple paths poison-reverse Poison reverse updates port Port and multicast address redistribute Redistribute IPv6 prefixes from another routing protocol split-horizon Split horizon updates summary-prefix Configure IPv6 summary prefix timers Adjust routing timers R2(config-rtr)#default  - R2(config-rtr)#default- R2(config-rtr)#default- R2(config-rtr)#default- R2(config-rtr)#default- R2(config-rtr)#default- R2(config-rtr)#default- R2(config-rtr)#default- R2(config-rtr)#default-        redistribute ospf 1 ipv router rip R2Ripredistribute ospf 1 me R2(config-rtr)#redistribute ospf 1 metric 2 R2(config-rtr)# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#sh ipv route IPv6 Routing Table - 9 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::/128 [120/4] via FE80::1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::/128 [0/0] via ::, Loopback0 R 2005:0:102::/64 [120/2] via FE80::1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:1203::3/128 [120/4] via FE80::1, FastEthernet0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] --More--   R4#p 2000:3:3:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/80/100 ms R4#p 2005:0:1203::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/64/76 ms R4#p 2005:0:1203::3 3 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R4#sh ipv route IPv6 Routing Table - 9 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::/128 [120/4] via FE80::1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::/128 [0/0] via ::, Loopback0 R 2005:0:102::/64 [120/2] via FE80::1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:1203::3/128 [120/4] via FE80::1, FastEthernet0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] --More--   R4# RACK9AS>3 [Resuming connection 3 to r3 ... ]  ! --More--   R3#sh ipv route IPv6 Routing Table - 10 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3::/128 [0/0] via ::, Loopback0 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::2, Serial1/2 C 2005:0:237::/64 [0/0] via ::, Serial1/0 L 2005:0:237::3/128 [0/0] via ::, Serial1/0 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203::2/128 [110/781] via FE80::2, Serial1/2 L 2005:0:1203::3/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] --More--   R3# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2(config-rtr)#redis R2(config-rtr)#redistribute con R2(config-rtr)#redistribute connected R2(config-rtr)#ipv rotuer ospf 1er ospf 1 er ospf 1 uer ospf 1ter ospf 1 R2(config-rtr)#ipv router ospf 1redistribute connected R2(config-rtr)#^Z R2# *Mar 1 00:39:02.422: %SYS-5-CONFIG_I: Configured from console by console R2# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#sh ipv route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::/128 [120/4] via FE80::1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::/128 [0/0] via ::, Loopback0 R 2005:0:102::/64 [120/2] via FE80::1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:237::/64 [120/3] via FE80::1, FastEthernet0/0 R 2005:0:702::/64 [120/3] via FE80::1, FastEthernet0/0 R 2005:0:1203::/64 [120/3] --More--   via FE80::1, FastEthernet0/0 R 2005:0:1203::3/128 [120/4] via FE80::1, FastEthernet0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R4#sh ipv routep 2005:0:1203::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/32 ms R4# RACK9AS>2 [Resuming connection 2 to r2 ... ] R2#sh run \ nb    | b router ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes area 20 virtual-link 3.3.3.3 redistribute connected redistribute rip R2Rip tag 2 ! ipv6 router rip R2Rip redistribute connected redistribute ospf 1 metric 2 ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous --More--   R2# RACK9AS> [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)#ipv ospf 1 area 0 R2(config-subif)#ipv ospf 1 area 0nt s 1/0.1  2 R2(config-subif)#int s 1/0.2pv ospf 1 area 0 R2(config-subif)#^Z R2# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0.1 R7(config-subif)#ipv ospf 1 area 0                pv router ospf 1 R7(config-rtr)#router R7(config-rtr)#router-id 7.7.7.7 R7(config-rtr)#int s 1/0.1 R7(config-subif)#ipv osp f  f 1 area 0 R7(config-subif)#ipv ospf 1 area 0nt s 1/0.1  2 R7(config-subif)#int s 1/0.2pv ospf 1 area 0 R7(config-subif)#^Z R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ipv ospf a 1 are 0 R3(config-if)#do sh ipc v ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:36 11 Serial1/2 R3(config-if)#^Z R3# *Mar 1 00:42:44.346: %SYS-5-CONFIG_I: Configured from console by console R3#ipv     deb ipv packopackspack packfpackpack pack fpack pack ^ % Invalid input detected at '^' marker. R3#deb ipv osf packpf pack OSPFv3 packet debugging is on R3# *Mar 1 00:43:02.785: OSPFv3: rcv. v:3 t:1 l:36 rid:7.7.7.7 aid:0.0.0.0 chk:EF5F inst:0 from Serial1/0 *Mar 1 00:43:03.017: OSPFv3: rcv. v:3 t:1 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:F96E inst:0 from Serial1/0 R3# *Mar 1 00:43:11.511: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.20 chk:F35C inst:0 from Serial1/2 R3#u all *Mar 1 00:43:12.717: OSPFv3: rcv. v:3 t:1 l:36 rid:7.7.7.7 aid:0.0.0.0 chk:EF5F inst:0 from Serial1/0 *Mar 1 00:43:13.033: OSPFv3: rcv. v:3 t:1 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:F96E inst:0 from Serial1/0 R3#u all All possible debugging has been turned off R3#deb ipv ospf ev OSPFv3 events debugging is on R3#deb ipv ospf ev  adj OSPFv3 adjacency events debugging is on R3#u all All possible debugging has been turned off R3#sh ipv ospf int Serial1/0 is up, line protocol is up Link Local Address FE80::3, Interface ID 9 Area 0, Process ID 1, Instance ID 0, Router ID 3.3.3.3 Network Type NON_BROADCAST, Cost: 781 Transmit Delay is 1 sec, State WAITING, Priority 1 No designated router on this network No backup designated router on this network Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 Hello due in 00:00:10 Wait time before Designated router selection 00:00:10 Index 1/2/4, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) OSPF_VL0 is up, line protocol is up Interface ID 28 Area 0, Process ID 1, Instance ID 0, Router ID 3.3.3.3 Network Type VIRTUAL_LINK, Cost: 781 Configured as demand circuit. Run as demand circuit. DoNotAge LSA allowed. --More-- RACK9AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#sh ipv ospf int Serial1/0.2 is up, line protocol is up Link Local Address FE80::7, Interface ID 28 Area 0, Process ID 1, Instance ID 0, Router ID 7.7.7.7 Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:08 Index 1/2/2, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 2, maximum is 2 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 2.2.2.2 Suppress hello for 0 neighbor(s) Serial1/0.1 is up, line protocol is up Link Local Address FE80::7, Interface ID 27 Area 0, Process ID 1, Instance ID 0, Router ID 7.7.7.7 Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:06 Index 1/1/1, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) --More--   R7# RACK9AS>3 [Resuming connection 3 to r3 ... ]   Transmit Delay is 1 sec, State POINT_TO_POINT, --More--   R3#deb ipv ospf pa OSPFv3 packet debugging is on R3#deb ipv ospf pa  e *Mar 1 00:44:42.724: OSPFv3: rcv. v:3 t:1 l:36 rid:7.7.7.7 aid:0.0.0.0 chk:EF5F inst:0 from Serial1/0 *Mar 1 00:44:42.985: OSPFv3: rcv. v:3 t:1 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:F96E inst:0 from Serial1/0 R3#deb ipv ospf ev OSPFv3 events debugging is on R3#deb ipv ospf ev  adj OSPFv3 adjacency events debugging is on R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ip *Mar 1 00:44:51.515: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.20 chk:F35C inst:0 from Serial1/2 R3(config-if)#ipv ospf *Mar 1 00:44:52.785: OSPFv3: rcv. v:3 t:1 l:36 rid:7.7.7.7 aid:0.0.0.0 chk:EF5F inst:0 from Serial1/0 *Mar 1 00:44:52.941: OSPFv3: rcv. v:3 t:1 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:F96E inst:0 from Serial1/0 R3(config-if)#ipv ospf net broa R3(config-if)# *Mar 1 00:44:57.577: OSPFv3: Interface Serial1/0 going Down *Mar 1 00:44:57.577: OSPFv3: Neighbor change Event on interface Serial1/0 *Mar 1 00:44:57.577: OSPFv3: DR/BDR election on Serial1/0 *Mar 1 00:44:57.577: OSPFv3: Elect BDR 0.0.0.0 *Mar 1 00:44:57.577: OSPFv3: Elect DR 0.0.0.0 *Mar 1 00:44:57.577: OSPFv3: Elect BDR 0.0.0.0 *Mar 1 00:44:57.581: OSPFv3: Elect DR 0.0.0.0 *Mar 1 00:44:57.581: DR: none BDR: none *Mar 1 00:44:57.581: OSPFv3: Flush network LSA immediately *Mar 1 00:44:57.581: OSPFv3: Remember old DR 3.3.3.3 (id) *Mar 1 00:44:57.581: OSPFv3: Interface Serial1/0 going Up R3(config-if)# *Mar 1 00:45:01.515: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.20 chk:F35C inst:0 from Serial1/2 R3(config-if)# *Mar 1 00:45:02.797: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:E951 inst:0 from Serial1/0 *Mar 1 00:45:02.801: OSPFv3: 2 Way Communication to 7.7.7.7 on Serial1/0, state 2WAY *Mar 1 00:45:02.958: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:F360 inst:0 from Serial1/0 *Mar 1 00:45:02.958: OSPFv3: 2 Way Communication to 2.2.2.2 on Serial1/0, state 2WAY R3(config-if)# *Mar 1 00:45:07.705: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:E269 inst:0 from Serial1/0 *Mar 1 00:45:07.705: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0x86F opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:07.705: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:07.713: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:DE28 inst:0 from Serial1/0 *Mar 1 00:45:07.713: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x16BF opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:07.713: OSPFv3: Nbr state is 2WAY R3(config-if)# *Mar 1 00:45:11.516: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.20 chk:F35C inst:0 from Serial1/2 R3(config-if)# *Mar 1 00:45:12.714: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:DE28 inst:0 from Serial1/0 *Mar 1 00:45:12.718: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x16BF opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:12.718: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:12.726: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:E269 inst:0 from Serial1/0 *Mar 1 00:45:12.726: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0x86F opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:12.730: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:12.734: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:E951 inst:0 from Serial1/0 R3(config-if)# *Mar 1 00:45:13.018: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:F360 inst:0 from Serial1/0 R3(config-if)# *Mar 1 00:45:17.722: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:DE28 inst:0 from Serial1/0 *Mar 1 00:45:17.726: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x16BF opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:17.726: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:17.734: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:E269 inst:0 from Serial1/0 *Mar 1 00:45:17.734: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0x86F opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:17.734: OSPFv3: Nbr state is 2WAY R3(config-if)# *Mar 1 00:45:21.516: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.20 chk:F35C inst:0 from Serial1/2 R3(config-if)# *Mar 1 00:45:22.730: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:DE28 inst:0 from Serial1/0 *Mar 1 00:45:22.734: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x16BF opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:22.734: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:22.742: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:E269 inst:0 from Serial1/0 *Mar 1 00:45:22.742: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0x86F opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:22.742: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:22.750: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:E951 inst:0 from Serial1/0 R3(config-if)# *Mar 1 00:45:23.034: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:F360 inst:0 from Serial1/0 R3(config-if)# *Mar 1 00:45:27.742: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:E269 inst:0 from Serial1/0 *Mar 1 00:45:27.742: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0x86F opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:27.742: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:27.750: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:DE28 inst:0 from Serial1/0 *Mar 1 00:45:27.750: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x16BF opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:27.750: OSPFv3: Nbr state is 2WAY R3(config-if)# *Mar 1 00:45:31.516: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.20 chk:F35C inst:0 from Serial1/2 R3(config-if)# *Mar 1 00:45:32.654: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:DE28 inst:0 from Serial1/0 *Mar 1 00:45:32.654: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x16BF opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:32.658: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:32.750: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:E269 inst:0 from Serial1/0 *Mar 1 00:45:32.750: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0x86F opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:32.750: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:32.762: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:E951 inst:0 from Serial1/0 R3(config-if)# *Mar 1 00:45:32.959: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:F360 inst:0 from Serial1/0 R3(config-if)# *Mar 1 00:45:37.582: OSPFv3: end of Wait on interface Serial1/0 *Mar 1 00:45:37.582: OSPFv3: DR/BDR election on Serial1/0 *Mar 1 00:45:37.582: OSPFv3: Elect BDR 7.7.7.7 *Mar 1 00:45:37.582: OSPFv3: Elect DR 7.7.7.7 *Mar 1 00:45:37.582: DR: 7.7.7.7 (Id) BDR: 7.7.7.7 (Id) *Mar 1 00:45:37.582: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0x14FB opt 0x0013 flag 0x7 len 28 *Mar 1 00:45:37.662: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:DE28 inst:0 from Serial1/0 *Mar 1 00:45:37.666: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x16BF opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:37.666: OSPFv3: Nbr state is 2WAY R3(config-if)# *Mar 1 00:45:37.759: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:E269 inst:0 from Serial1/0 *Mar 1 00:45:37.759: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0x86F opt 0x0013 flag 0x7 len 28 mtu 1500 state EXSTART *Mar 1 00:45:37.759: OSPFv3: NBR Negotiation Done. We are the SLAVE *Mar 1 00:45:37.759: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0x86F opt 0x0013 flag 0x2 len 368 *Mar 1 00:45:38.043: OSPFv3: rcv. v:3 t:2 l:368 rid:7.7.7.7 aid:0.0.0.0 chk:1890 inst:0 from Serial1/0 *Mar 1 00:45:38.043: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0x870 opt 0x0013 flag 0x3 len 368 mtu 1500 state EXCHANGE *Mar 1 00:45:38.043: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0x870 opt 0x0013 flag 0x0 len 28 *Mar 1 00:45:38.047: OSPFv3: Database request to 7.7.7.7 *Mar 1 00:45:38.047: OSPFv3: sent LS REQ packet to FE80::7, length 12 *Mar 1 00:45:38.055: OSPFv3: rcv. v:3 t:3 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:C497 inst:0 from Serial1/0 *Mar R3(config-if)# 1 00:45:38.159: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:E26D inst:0 from Serial1/0 *Mar 1 00:45:38.159: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0x871 opt 0x0013 flag 0x1 len 28 mtu 1500 state EXCHANGE *Mar 1 00:45:38.159: OSPFv3: Exchange Done with 7.7.7.7 on Serial1/0 *Mar 1 00:45:38.159: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0x871 opt 0x0013 flag 0x0 len 28 *Mar 1 00:45:38.179: OSPFv3: rcv. v:3 t:4 l:76 rid:7.7.7.7 aid:0.0.0.0 chk:2866 inst:0 from Serial1/0 *Mar 1 00:45:38.179: OSPFv3: Synchronized with 7.7.7.7 on Serial1/0, state FULL *Mar 1 00:45:38.183: %OSPFv3-5-ADJCHG: Process 1, Nbr 7.7.7.7 on Serial1/0 from LOADING to FULL, Loading Done *Mar 1 00:45:38.684: Insert LSA 0 adv_rtr 3.3.3.3, type 0x2009 in maxage *Mar 1 00:45:38.772: OSPFv3: rcv. v:3 t:4 l:76 rid:7.7.7.7 aid:0.0.0.0 chk:3D1E inst:0 from Serial1/0 *Mar 1 00:45:38.832: OSPFv3: rcv. v:3 t:4 l:76 rid:2.2.2.2 aid:0.0.0.0 chk:60A1 inst:0 from Serial1/2 *Mar 1 00:45:38.965: OSPFv3: rcv. v:3 t:4 l:52 rid:7.7.7.7 aid:0.0.0.0 chk:D994 inst:0 from Serial1/0 R3(config-if)# R3(config-if)# *Mar 1 00:45:40.667: OSPFv3: rcv. v:3 t:5 l:56 rid:7.7.7.7 aid:0.0.0.0 chk:749F inst:0 from Serial1/0 *Mar 1 00:45:41.240: OSPFv3: rcv. v:3 t:5 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:A340 inst:0 from Serial1/2 *Mar 1 00:45:41.517: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.20 chk:F35C inst:0 from Serial1/2 R3(config-if)# *Mar 1 00:45:42.671: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:DE28 inst:0 from Serial1/0 *Mar 1 00:45:42.671: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x16BF opt 0x0013 flag 0x7 len 28 mtu 1500 state 2WAY *Mar 1 00:45:42.675: OSPFv3: Nbr state is 2WAY *Mar 1 00:45:42.767: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:E951 inst:0 from Serial1/0 *Mar 1 00:45:42.975: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:F360 inst:0 from Serial1/0 *Mar 1 00:45:43.480: OSPFv3: rcv. v:3 t:4 l:76 rid:7.7.7.7 aid:0.0.0.0 chk:3D1A inst:0 from Serial1/0 R3(config-if)#do *Mar 1 00:45:43.772: OSPFv3: rcv. v:3 t:4 l:52 rid:7.7.7.7 aid:0.0.0.0 chk:D994 inst:0 from Serial1/0 R3(config-if)#do u all All possible debugging has been turned off R3(config-if)# *Mar 1 00:45:45.371: OSPFv3: rcv. v:3 t:5 l:36 rid:7.7.7.7 aid:0.0.0.0 chk:A888 inst:0 from Serial1/0 *Mar 1 00:45:45.740: OSPFv3: rcv. v:3 t:5 l:36 rid:2.2.2.2 aid:0.0.0.20 chk:5A15 inst:0 from Serial1/2 R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#sh ip  v route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/1562] via FE80::2, Serial1/0.2 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::7/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::2, Serial1/0.2 OI 2005:0:1203::2/128 [110/781] --More--   via FE80::2, Serial1/0.2 OI 2005:0:1203::3/128 [110/1562] via FE80::2, Serial1/0.2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#sh ipv osp fnei ^ % Invalid input detected at '^' marker. R7#sh ipv osp fneinei  Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:38 28 Serial1/0.2 3.3.3.3 1 FULL/ - 00:00:30 9 Serial1/0.1 R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#^Z R3# *Mar 1 00:47:12.798: %SYS-5-CONFIG_I: Configured from console by console R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 2WAY/DROTHER 00:00:34 27 Serial1/0 7.7.7.7 1 FULL/DR 00:00:39 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:32 11 Serial1/2 R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh ipv ospf data OSPFv3 Router with ID (7.7.7.7) (Process ID 1) Router Link States (Area 0) ADV Router Age Seq# Fragment ID Link count Bits 2.2.2.2 47 0x80000009 0 2 EB 3.3.3.3 41 0x80000008 0 2 B 7.7.7.7 145 0x80000003 0 2 None Inter Area Prefix Link States (Area 0) ADV Router Age Seq# Prefix 2.2.2.2 913 0x80000001 2005:0:1203::/64 2.2.2.2 913 0x80000001 2005:0:1203::2/128 2.2.2.2 913 0x80000001 2005:0:1203::3/128 3.3.3.3 12 (DNA) 0x80000001 2005:0:1203::/64 3.3.3.3 12 (DNA) 0x80000001 2005:0:1203::2/128 3.3.3.3 12 (DNA) 0x80000001 2000:3:3::/128 3.3.3.3 2 (DNA) 0x80000001 2005:0:1203::3/128 Inter Area Router Link States (Area 0) --More--   R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ipv ospf net po R3(config-if)#ipv ospf net point-to-m R3(config-if)# *Mar 1 00:49:22.711: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from 2WAY to DOWN, Neighbor Down: Interface down or detached *Mar 1 00:49:22.711: %OSPFv3-5-ADJCHG: Process 1, Nbr 7.7.7.7 on Serial1/0 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)# *Mar 1 00:49:22.832: %OSPFv3-4-NONEIGHBOR: Received database description from unknown neighbor 2.2.2.2 R3(config-if)#ipv ospf h R3(config-if)#ipv ospf hello-interval 10 *Mar 1 00:49:32.748: %OSPFv3-4-NONEIGHBOR: Received database description from unknown neighbor 2.2.2.2 R3(config-if)#ipv ospf hello-interval 10 R3(config-if)# *Mar 1 00:49:37.768: %OSPFv3-4-NONEIGHBOR: Received database description from unknown neighbor 2.2.2.2 R3(config-if)#^Z R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip  v ospf int *Mar 1 00:49:38.040: %OSPFv3-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Serial1/0.1 from LOADING to FULL, Loading Done R7#sh ipv ospf int Serial1/0.2 is up, line protocol is up Link Local Address FE80::7, Interface ID 28 Area 0, Process ID 1, Instance ID 0, Router ID 7.7.7.7 Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:09 Index 1/2/2, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 1, maximum is 4 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 2.2.2.2 Suppress hello for 0 neighbor(s) Serial1/0.1 is up, line protocol is up Link Local Address FE80::7, Interface ID 27 Area 0, Process ID 1, Instance ID 0, Router ID 7.7.7.7 Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:07 Index 1/1/1, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) --More--   R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] *Mar R3# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#shipv route ^ % Invalid input detected at '^' marker. R7#shipv route ipv route IPv6 Routing Table - 13 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/0.1 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] --More--   R7# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#do sh ipv ospf net i ^ % Invalid input detected at '^' marker. R3#do sh ipv ospf neido sh ipv ospf nei  sh ipv ospf nei  Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 INIT/ - 00:00:36 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:35 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:34 11 Serial1/2 R3#sh run int s  1/0 Building configuration... Current configuration : 365 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local ipv6 ospf network point-to-multipoint ipv6 ospf hello-interval 10 ipv6 ospf 1 area 0 frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast end R3#deb ipv ospf ev OSPFv3 events debugging is on R3# *Mar 1 00:52:28.235: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x216D opt 0x0013 flag 0x7 len 28 mtu 1500 state EXSTART *Mar 1 00:52:28.235: OSPFv3: First DBD and we are not SLAVE *Mar 1 00:52:28.247: OSPFv3: Send DBD to 2.2.2.2 on Serial1/0 seq 0xCCB opt 0x0013 flag 0x7 len 28 *Mar 1 00:52:28.247: OSPFv3: Retransmitting DBD to 2.2.2.2 on Serial1/0 [12] R3# *Mar 1 00:52:33.244: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x216D opt 0x0013 flag 0x7 len 28 mtu 1500 state EXSTART *Mar 1 00:52:33.244: OSPFv3: First DBD and we are not SLAVE *Mar 1 00:52:33.248: OSPFv3: Send DBD to 2.2.2.2 on Serial1/0 seq 0xCCB opt 0x0013 flag 0x7 len 28 *Mar 1 00:52:33.248: OSPFv3: Retransmitting DBD to 2.2.2.2 on Serial1/0 [13] R3# *Mar 1 00:52:38.248: OSPFv3: Send DBD to 2.2.2.2 on Serial1/0 seq 0xCCB opt 0x0013 flag 0x7 len 28 *Mar 1 00:52:38.248: OSPFv3: Retransmitting DBD to 2.2.2.2 on Serial1/0 [14] *Mar 1 00:52:38.252: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x216D opt 0x0013 flag 0x7 len 28 mtu 1500 state EXSTART *Mar 1 00:52:38.252: OSPFv3: First DBD and we are not SLAVE R3# *Mar 1 00:52:43.248: OSPFv3: Send DBD to 2.2.2.2 on Serial1/0 seq 0xCCB opt 0x0013 flag 0x7 len 28 *Mar 1 00:52:43.248: OSPFv3: Retransmitting DBD to 2.2.2.2 on Serial1/0 [15] *Mar 1 00:52:43.260: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x216D opt 0x0013 flag 0x7 len 28 mtu 1500 state EXSTART *Mar 1 00:52:43.260: OSPFv3: First DBD and we are not SLAVE R3# *Mar 1 00:52:48.248: OSPFv3: Send DBD to 2.2.2.2 on Serial1/0 seq 0xCCB opt 0x0013 flag 0x7 len 28 *Mar 1 00:52:48.248: OSPFv3: Retransmitting DBD to 2.2.2.2 on Serial1/0 [16] *Mar 1 00:52:48.268: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x216D opt 0x0013 flag 0x7 len 28 mtu 1500 state EXSTART *Mar 1 00:52:48.268: OSPFv3: First DBD and we are not SLAVE R3#u all All possible debugging has been turned off R3#deb fram pack Frame Relay packet debugging is on R3# *Mar 1 00:52:58.068: Serial1/0: broadcast search *Mar 1 00:52:58.068: Serial1/0: Broadcast on DLCI 302 link 79 *Mar 1 00:52:58.068: Serial1/0(o): dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 00:52:58.068: Serial1/0: Broadcast on DLCI 307 link 79 *Mar 1 00:52:58.068: Serial1/0(o): dlci 307(0x4C31), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 00:52:58.068: Serial1/0(o): dlci 307(0x4C31), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 00:52:58.128: broadcast dequeue *Mar 1 00:52:58.128: Serial1/0(o):Pkt sent on dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 00:52:58.128: broadcast dequeue R3# *Mar 1 00:52:58.128: Serial1/0(o):Pkt sent on dlci 307(0x4C31), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 00:52:58.128: broadcast dequeue *Mar 1 00:52:58.128: Serial1/0(o):Pkt sent on dlci 307(0x4C31), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 00:52:58.249: Serial1/0:Encaps failed--no map entry link 79(IPV6) *Mar 1 00:52:58.285: Serial1/0(i): dlci 302(0x48E1), pkt type 0x86DD, datagramsize 72 R3#u all All possible debugging has been turned off R3# *Mar 1 00:53:38.250: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from EXSTART to DOWN, Neighbor Down: Too many retransmits R3#u all All possible debugging has been turned off R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int s 1/0 R3(config-if)#fram map ipv fe80::2 302 br R3(config-if)#^Z R3# *Mar 1 00:54:00.847: %SYS-5-CONFIG_I: Configured from console by console R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 DOWN/ - - 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:37 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:36 11 Serial1/2 R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 DOWN/ - - 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:37 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:36 11 Serial1/2 R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 DOWN/ - - 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:36 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:34 11 Serial1/2 R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 DOWN/ - - 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:35 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:34 11 Serial1/2 R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 DOWN/ - - 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:35 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:34 11 Serial1/2 R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 DOWN/ - - 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:35 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:33 11 Serial1/2 R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 DOWN/ - - 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:34 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:33 11 Serial1/2 R3# *Mar 1 00:54:38.253: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from DOWN to DOWN, Neighbor Down: Ignore timer expired R3# *Mar 1 00:54:43.473: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from LOADING to FULL, Loading Done R3#sh ipv ospf neiconfi t sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:37 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:37 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:36 11 Serial1/2 R3#ping 2005:           RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh ipv route IPv6 Routing Table - 13 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/0.1 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] --More--   via FE80::2, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::2, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#ping 2005:0:104::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/89/93 ms R7# RACK9AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run | b 1/0 interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ipv6 address FE80::2 link-local ipv6 rip R2Rip enable ! interface Serial1/2 --More--   R2# RACK9AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b     int s 1/0 Building configuration... Current configuration : 409 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local ipv6 ospf network point-to-multipoint ipv6 ospf hello-interval 10 ipv6 ospf 1 area 0 frame-relay map ipv6 FE80::2 302 broadcast frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast end R3#^x7    RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b 1/0 interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80::7 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::7/64 ipv6 address FE80::7 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown --More--   R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int tu 0 R7(config-if)#k *Mar 1 00:57:19.625: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R7(config-if)#kee R7(config-if)#keepalive R7(config-if)#tun fa 0/1 ^ % Invalid input detected at '^' marker. R7(config-if)#tun fa 0/1n sfa 0/1ofa 0/1ufa 0/1 fa 0/1 R7(config-if)#tun de 180.40.7.66 R7(config-if)#ipv *Mar 1 00:57:40.616: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R7(config-if)#ipv add 22~ 005    00: 5:0:17::7/64 R7(config-if)#ipv rip R7R Rip en R7(config-if)#^Z R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#int tu 0 R1(config-if)#keep R1(config-if)# *Mar 1 00:59:17.767: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#tun sou e 0/0 R1(config-if)#tun dest 19-  80.40.7.1 R1(config-if)# *Mar 1 00:59:30.873: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-if)#ipv addd 200      2005:0:17::1/64 R1(config-if)#ipv rip R1Rip en R1(config-if)#^Z R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Mar 1 R7#sh ipv rout IPv6 Routing Table - 15 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/0.1 C 2005:0:17::/64 [0/0] via ::, Tunnel0 L 2005:0:17::7/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] --More--   via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::2, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::2, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#ping 2006 5:0:17::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:17::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/11/24 ms R7#ping 2005:0:17::1 ping 2005:0:17::1sh ipv rout  IPv6 Routing Table - 16 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/0.1 R 2000:4:4::/64 [120/3] via FE80::2D0:BBFF:FEE9:6060, Tunnel0 C 2005:0:17::/64 [0/0] via ::, Tunnel0 L 2005:0:17::7/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] --More--   R7#pin 2000:4:4::~ % Unrecognized host or address, or protocol not running. R7#pin 2000:4:4::~  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms R7#tclsh R7(tcl)#foreach test { +>(tcl)#2000:4:4:: +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3:: +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)#!2006:1:1:: +>(tcl)#!2006:2:2:: +>(tcl)#!2006:3:3:: +>(tcl)#!2006:4:4:: +>(tcl)#!2006:7:7:: +>(tcl)# +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/99/112 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/85/89 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/101/121 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 164/166/169 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/5 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms % Ambiguous command: "ping !2006:1:1:: rep 2" R7(tcl)#tclsh R7(tcl)#foreach test { +>(tcl)#2000:4:4:: +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3:: +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)# +>(tcl)# +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/97/116 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/86/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/99/112 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 164/167/169 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R7# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#tclsh R4(tcl)#foreach test { +>(tcl)#2000:4:4:: +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3:: +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)# +>(tcl)# +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/12/36 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/38/64 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/40/64 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/84/100 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 76/78/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/104/128 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/118/120 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/104/144 ms R4# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#tclsh R1(tcl)#foreach test { +>(tcl)#2000:4:4:: +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3:: +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)# +>(tcl)# +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/43/64 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/43/69 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/34/48 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/69/80 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/83/101 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/72/72 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/118/124 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/87/89 ms R1# R1# R1# R1#sh run |   int tu 0 Building configuration... Current configuration : 167 bytes ! interface Tunnel0 no ip address ipv6 address 2005:0:17::1/64 ipv6 rip R1Rip enable keepalive 10 3 tunnel source Ethernet0/0 tunnel destination 180.40.7.1 end R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int tu 0 Building configuration... Current configuration : 172 bytes ! interface Tunnel0 no ip address ipv6 address 2005:0:17::7/64 ipv6 rip R7Rip enable keepalive 10 3 tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 end R7#sh int tu 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive set (10 sec), retries 3 Tunnel source 180.40.7.1 (FastEthernet0/1), destination 180.40.7.66 Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled Tunnel TTL 255 Checksumming of packets disabled, fast tunneling enabled Last input 00:00:04, output 00:00:02, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 60 packets input, 6660 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 70 packets output, 5728 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R7# R7#conf t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int tu 0 R7(config-if)#tun mode ipv R7(config-if)#tun mode ipv6ip R7(config-if)#^Z R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#iont     nt  tu 0 R1(config-if)#tun mode ipv R1(config-if)#tun mode ipv6ip R1(config-if)#^Z R1# *Mar 1 01:04:51.186: %SYS-5-CONFIG_I: Configured from console by console R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#tclsh R7(tcl)#foreach test { +>(tcl)#2000:4:4:: +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3:: +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)# +>(tcl)# +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/90/92 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 85/87/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/86/89 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 164/165/168 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/67/100 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms R7# R7# R7# R7# R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#sh run int rtu   tu 0 Building configuration... Current configuration : 187 bytes ! interface Tunnel0 no ip address ipv6 address 2005:0:17::1/64 ipv6 rip R1Rip enable keepalive 10 3 tunnel source Ethernet0/0 tunnel destination 180.40.7.1 tunnel mode ipv6ip end R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int tu 0 Building configuration... Current configuration : 192 bytes ! interface Tunnel0 no ip address ipv6 address 2005:0:17::7/64 ipv6 rip R7Rip enable keepalive 10 3 tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 tunnel mode ipv6ip end R7#sh int tu 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive set (10 sec), retries 3 Tunnel source 180.40.7.1 (FastEthernet0/1), destination 180.40.7.66 Tunnel protocol/transport IPv6/IP, key disabled, sequencing disabled Tunnel TTL 255 Checksumming of packets disabled, fast tunneling enabled Last input 00:00:16, output 00:00:05, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 73 packets input, 8516 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 87 packets output, 7248 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R7# R7# R7# R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int ut  tu 0 R7(config-if)#shut R7(config-if)# *Mar 1 01:05:26.996: %LINK-5-CHANGED: Interface Tunnel0, changed state to administratively down *Mar 1 01:05:27.998: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R7(config-if)#do sh run int tu 0 Building configuration... Current configuration : 202 bytes ! interface Tunnel0 no ip address shutdown ipv6 address 2005:0:17::7/64 ipv6 rip R7Rip enable keepalive 10 3 tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 tunnel mode ipv6ip end R7(config-if)#no tunnel destination 180.40.7.66 R7(config-if)#no ipv6 rip R7Rip enable R7(config-if)#no ipv6 address 2005:0:17::7/64 R7(config-if)# tunnel mode ipv6ip ? 6to4 IPv6 automatic tunnelling using 6to4 auto-tunnel IPv6 automatic tunnelling using IPv4 compatible addresses isatap IPv6 automatic tunnelling using ISATAP R7(config-if)# tunnel mode ipv6ip 6 R7(config-if)# tunnel mode ipv6ip 6to4 R7(config-if)#ipv add 2002:b428:701::/64 R7(config-if)#exit R7(config)#ipv route 2002:/16 tu 0 ^ % Invalid input detected at '^' marker. R7(config)#ipv route 2002:/16 tu 0:/16 tu 0 R7(config)# RACK9AS>1 [Resuming connection 1 to r1 ... ] R1#conf ti  t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0 R1(config-if)#do sh tiu   run int tu 0 Building configuration... Current configuration : 187 bytes ! interface Tunnel0 no ip address ipv6 address 2005:0:17::1/64 ipv6 rip R1Rip enable keepalive 10 3 tunnel source Ethernet0/0 tunnel destination 180.40.7.1 tunnel mode ipv6ip end R1(config-if)#no ipv6 address 2005:0:17::1/64 R1(config-if)#no ipv6 rip R1Rip enable R1(config-if)#m no keepalive 10 3 R1(config-if)#no tunnel destination 180.40.7.1 R1(config-if)#tun mode ipv 6 ^ % Invalid input detected at '^' marker. R1(config-if)#tun mode ipv 6   R1(config-if)#tun mode ipv6ip 6 R1(config-if)#tun mode ipv6ip 6to4 R1(config-if)#ipv add 2002:b428:4201    742::/64 R1(config-if)#exit R1(config)#ipv route 2002::/16 tun 0 R1(config)#^Z R1# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7(config)#int tu 0 R7(config-if)#no keep R7(config-if)#no shut R7(config-if)#^Z R7# *Mar 1 01:08:38.987: %SYS-5-CONFIG_I: Configured from console by console R7# *Mar 1 01:08:40.662: %LINK-3-UPDOWN: Interface Tunnel0, changed state to up *Mar 1 01:08:41.663: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R7#ping 2002:b428:742:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:742::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R7#sh ipv route IPv6 Routing Table - 16 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/0.1 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] --More--   R7#conf t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv 2000:4:4::/64 2002:b428:742:: ^ % Invalid input detected at '^' marker. R7(config)#ipv 2000:4:4::/64 2002:b428:742:: r2000:4:4::/64 2002:b428:742::o2000:4:4::/64 2002:b428:742::u2000:4:4::/64 2002:b428:742::t2000:4:4::/64 2002:b428:742::e2000:4:4::/64 2002:b428:742:: 2000:4:4::/64 2002:b428:742:: R7(config)#^Z R7# *Mar 1 01:10:44.849: %SYS-5-CONFIG_I: Configured from console by console R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv     do sh rru  un | pref sh run | pref ^ % Invalid input detected at '^' marker. R1(config)#do sh run | prefipref pref distribute-list prefix-list NoR4Loop out Serial0/1 ipv6 prefix-list NoR4Loop seq 5 deny 2000:4:4::/64 ipv6 prefix-list NoR4Loop seq 10 permit ::/0 le 128 R1(config)#ipv6 prefix-list NoR4Loop seq 7 de 2002:/16 ^ % Invalid input detected at '^' marker. R1(config)#ipv6 prefix-list NoR4Loop seq 7 de 2002:/16:/16 R1(config)#router        ipv rotuer rip R1Rip ^ % Invalid input detected at '^' marker. R1(config)#ipv rotuer rip R1Riper rip R1Rip er rip R1Rip uer rip R1Ripter rip R1Rip R1(config-rtr)#redis R1(config-rtr)#redistribute stat R1(config-rtr)#redistribute static me R1(config-rtr)#redistribute static metric 3 R1(config-rtr)#^Z R1# RACK9AS>4 [Resuming connection 4 to r4 ... ] R4#sh ipv route IPv6 Routing Table - 14 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::/128 [120/4] via FE80::1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::/128 [0/0] via ::, Loopback0 R 2002::/16 [120/4] via FE80::1, FastEthernet0/0 R 2005:0:102::/64 [120/2] via FE80::1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:237::/64 [120/3] via FE80::1, FastEthernet0/0 R 2005:0:237::3/128 [120/4] --More--   R4# RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#ping 2000:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R7# RACK9AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh run | t b tu  Tyu  u interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:742::/64 tunnel source Ethernet0/0 tunnel mode ipv6ip 6to4 ! interface Ethernet0/0 ip address 180.40.7.66 255.255.255.224 half-duplex ! interface Serial0/0 no ip address shutdown ! interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::1/64 ipv6 address FE80::1 link-local ipv6 rip R1Rip enable ! interface Serial0/1 --More--   no ip address ipv6 address 2005:0:102::1/64 ipv6 address FE80::1 link-local ipv6 rip R1Rip enable clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! ip http server ip classless ! ! ipv6 route 2002::/16 Tunnel0 ipv6 router rip R1Rip redistribute static metric 3 distribute-list prefix-list NoR4Loop out Serial0/1 ! ! ! ipv6 prefix-list NoR4Loop seq 5 deny 2000:4:4::/64 --More-- RACK9AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int       | b tun==     Tu interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:701::/64 tunnel source FastEthernet0/1 tunnel mode ipv6ip 6to4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.1 255.255.255.224 duplex auto speed auto ! interface Serial1/0 --More--   no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80::7 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::7/64 ipv6 address FE80::7 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! --More--  interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router rip version 2 network 180.40.0.0 --More--   no auto-summary ! ip classless ! ip http server no ip http secure-server ! ipv6 route 2000:4:4::/64 2002:B428:742:: ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! ipv6 router rip R7Rip ! ! ! ! ! ! ! ! ! --More--   R7#sh int tu 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source 180.40.7.1 (FastEthernet0/1), destination UNKNOWN Tunnel protocol/transport IPv6 6to4, key disabled, sequencing disabled Checksumming of packets disabled Last input 00:02:02, output 00:02:02, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 85 packets input, 10500 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 102 packets output, 8892 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R7# R7#