=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.11.28 08:00:15 =~=~=~=~=~=~=~=~=~=~=~= sh run int s 1/0.2 Building configuration... Current configuration : 157 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 702 end R7#sh run int s 1/0.2 1 Building configuration... Current configuration : 213 bytes ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive end R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)# R7(config)# R7(config)#do sh access-list R7(config)#ip access-list sta R7(config)#ip access-list standard S5 R7(config-std-nacl)#per 208.28.1.2 R7(config-std-nacl)#exit R7(config)#class R7(config)#class-map S5Telnet R7(config-cmap)#match acc R7(config-cmap)#match access-group S5 ^ % Invalid input detected at '^' marker. R7(config-cmap)#match access-group S5  ? <1-2699> Access list index name Named Access List R7(config-cmap)#match access-group name S5 R7(config-cmap)#match pro R7(config-cmap)#match protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 --More--   custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching (Direct encapsulation only) dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) --More--   ipsec IP Security Protocol (ESP/AH) ipv6 IPV6 ipx Novell IPX irc Internet Relay Chat kazaa2 Kazaa Version 2 kerberos Kerberos l2tp L2F/L2TP tunnel ldap Lightweight Directory Access Protocol llc2 llc2 napster Napster Traffic netbios NetBIOS netshow Microsoft Netshow nfs Network File System nntp Network News Transfer Protocol notes Lotus Notes(R) novadigm Novadigm EDM ntp Network Time Protocol pad PAD links pcanywhere Symantec pcANYWHERE pop3 Post Office Protocol pppoe PPP over Ethernet pptp Point-to-Point Tunneling Protocol printer print spooler/lpd --More--   qllc qllc protocol rcmd BSD r-commands (rsh, rlogin, rexec) rip Routing Information Protocol rsrb Remote Source-Route Bridging rsvp Resource Reservation Protocol rtp Real Time Protocol rtspplayer RTSP players streaming protocol secure-ftp FTP over TLS/SSL secure-http Secured HTTP secure-imap Internet Message Access Protocol over TLS/SSL secure-irc Internet Relay Chat over TLS/SSL secure-ldap Lightweight Directory Access Protocol over TLS/SSL secure-nntp Network News Transfer Protocol over TLS/SSL secure-pop3 Post Office Protocol over TLS/SSL secure-telnet Telnet over TLS/SSL smtp Simple Mail Transfer Protocol snapshot Snapshot routing support snmp Simple Network Management Protocol socks SOCKS sqlnet SQL*NET for Oracle sqlserver MS SQL Server ssh Secured Shell streamwork Xing Technology StreamWorks player --More--   stun Serial Tunnel sunrpc Sun RPC syslog System Logging Utility telnet Telnet tftp Trivial File Transfer Protocol vdolive VDOLive streaming video vofr voice over Frame Relay packets xwindows X-Windows remote access R7(config-cmap)#match protocol telnet R7(config-cmap)#exit R7(config)#clas R7(config)#class-map S5Other R7(config-cmap)#class-map S5Otherexit match protocol telnetaccess-group name S5 R7(config-cmap)#exit R7(config)#Prob R7(config)#Prob   R7(config)#Pr  pol R7(config)#policy-map Prob5 R7(config-pmap)#exiy ^ % Invalid input detected at '^' marker. R7(config-pmap)#exit R7(config)#class R7(config)#class-map j JPG R7(config-cmap)#mat R7(config-cmap)#match pro R7(config-cmap)#match protocol he t R7(config-cmap)#match protocol http ? host Server Host Name mime Match MIME Type url Match URL String R7(config-cmap)#match protocol http url ? WORD Enter a string as the sub-protocol parameter R7(config-cmap)#match protocol http url *.jpg R7(config-cmap)#match protocol http url *.jpg e R7(config-cmap)#match protocol http url *.jpeg R7(config-cmap)#match protocol http url *.jpeg *.jpeg  *.jpeg  *.jpeg m *.jpegi *.jpegm *.jpege *.jpeg *.jpeg  R7(config-cmap)#match protocol http mime *jpeg  R7(config-cmap)#match protocol http mime *jpe g R7(config-cmap)#do sh class Class Map match-all S5Other (id 2) Match access-group name S5 Class Map match-any class-default (id 0) Match any Class Map match-all S5Telnet (id 1) Match access-group name S5 Match protocol telnet Class Map match-all JPG (id 3) Match protocol http url "*.jpg" Match protocol http url "*.jpe" Match protocol http url "*.jpeg" Match protocol http mime "*jpeg" Match protocol http mime "*jpe" Match protocol http mime "*jpg" R7(config-cmap)#exit R7(config)#exitdo sh classmatch protocol http mime *jpgegurl *.jpeg gclass-map JPG mJPGaJPGtJPGcJPGhJPG-JPGnJPGaJPGJPG JPG aJPGnJPGyJPG JPG R7(config-cmap)#class-map match-any JPGexit do sh class Class Map match-all S5Other (id 2) Match access-group name S5 Class Map match-any class-default (id 0) Match any Class Map match-all S5Telnet (id 1) Match access-group name S5 Match protocol telnet Class Map match-any JPG (id 3) Match protocol http url "*.jpg" Match protocol http url "*.jpe" Match protocol http url "*.jpeg" Match protocol http mime "*jpeg" Match protocol http mime "*jpe" Match protocol http mime "*jpg" R7(config-cmap)#exit R7(config)#pol R7(config)#policy-map Prob5 R7(config-pmap)#clas R7(config-pmap)#class j JGP % class map JGP not configured R7(config-pmap)#class JGP  PG R7(config-pmap-c)#sh R7(config-pmap-c)#shape ? adaptive Enable Traffic Shaping adaptation to BECN average configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc only per interval fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fr-voice-adapt Enable rate adjustment depending on voice presence max-buffers Set Maximum Buffer Limit peak configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc+Be per interval R7(config-pmap-c)#shape pe R7(config-pmap-c)#shape peak % Incomplete command. R7(config-pmap-c)#shape peak ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R7(config-pmap-c)#shape peak 10000   00000 ? <256-154400000> bits per interval, sustained. Needs to be multiple of 128. Recommend not to configure it, the algorithm will find out the best value R7(config-pmap-c)#shape peak 1000000 R7(config-pmap-c)#do sh pol Policy Map Prob5 Class JPG Traffic Shaping Peak Rate Traffic Shaping CIR 1000000 (bps) Max. Buffers Limit 1000 (Packets) R7(config-pmap-c)#int s   f 0/1 R7(config-if)#serv R7(config-if)#service-policy out Prob5 R7(config-if)#service-policy out Prob5int f 0/1 do sh pol int fa 0/1 FastEthernet0/1 Service-policy output: Prob5 Class-map: JPG (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol http url "*.jpg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpe" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http mime "*jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http mime "*jpe" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http mime "*jpg" --More--   0 packets, 0 bytes 5 minute rate 0 bps Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 2000000/1000000 6250 25000 25000 25 6250 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no Class-map: class-default (match-any) 1 packets, 60 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R7(config-if)#do sh pol int fa 0/1service-policy out Prob5int f 0/1 do sh polshape peak 1000000  class JPG GPpolicy-map Prob5 R7(config-pmap)#class JPG R7(config-pmap-c)#class JPGpolicy-map Prob5do sh pol int fa 0/1service-policy out Prob5int f 0/1 do sh polshape peak 1000000  1000000  1000000  1000000  1000000 a 1000000 v 1000000 g 1000000  ^ % Invalid input detected at '^' marker. R7(config-pmap-c)#shape avg 1000000  1000000  R7(config-pmap-c)#shape av 1000000 g 1000000 class JPG policy-map Prob5do sh pol int fa 0/1 FastEthernet0/1 Service-policy output: Prob5 Class-map: JPG (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol http url "*.jpg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpe" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http mime "*jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http mime "*jpe" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http mime "*jpg" --More--   0 packets, 0 bytes 5 minute rate 0 bps Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 1000000/1000000 6250 25000 25000 25 3125 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no Class-map: class-default (match-any) 15 packets, 1468 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R7(config-pmap-c)#exit R7(config-pmap)#class S5Telnet R7(config-pmap-c)#ba R7(config-pmap-c)#bandwidth ? <8-2000000> Kilo Bits per second percent % of total Bandwidth remaining % of the remaining bandwidth R7(config-pmap-c)#bandwidth 1000 R7(config-pmap-c)#exit R7(config-pmap)#exitbandwidth 1000class S5Telnet      Other R7(config-pmap-c)#pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 5000000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 5000000 co R7(config-pmap-c)#police 5000000 conform-action ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#police 5000000 conform-action se R7(config-pmap-c)#police 5000000 conform-action set-p R7(config-pmap-c)#police 5000000 conform-action set-prec-transmit 3 ? exceed-action action when rate is within conform and conform + exceed burst R7(config-pmap-c)#police 5000000 conform-action set-prec-transmit 3 ex R7(config-pmap-c)#$000 conform-action set-prec-transmit 3 exceed-action s R7(config-pmap-c)#$000 conform-action set-prec-transmit 3 exceed-action set-p R7(config-pmap-c)#$et-prec-transmit 3 exceed-action set-prec-transmit 1 R7(config-pmap-c-police)#$ansmit 3 exceed-action set-prec-transmit 1 do sh pol int fa 0/1 FastEthernet0/1 Service-policy output: Prob5 Class-map: JPG (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol http url "*.jpg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpe" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http mime "*jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http mime "*jpe" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http mime "*jpg" --More--   0 packets, 0 bytes 5 minute rate 0 bps Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 1000000/1000000 6250 25000 25000 25 3125 Adapt Queue Packets Bytes Packets Bytes Shaping Active Depth Delayed Delayed Active - 0 0 0 0 0 no Class-map: S5Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group name S5 Match: protocol telnet Queueing Output Queue: Conversation 265 Bandwidth 1000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: S5Other (match-all) --More--   0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group name S5 police: cir 5000000 bps, bc 156250 bytes conformed 0 packets, 0 bytes; actions: set-prec-transmit 3 exceeded 0 packets, 0 bytes; actions: set-prec-transmit 1 conformed 0 bps, exceed 0 bps Class-map: class-default (match-any) 45 packets, 4446 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R7(config-pmap-c-police)#in  clas    exit R7(config-pmap-c)#exit R7(config-pmap)#class S5Telnet R7(config-pmap-c)#fa R7(config-pmap-c)#fa> ? % Unrecognized command R7(config-pmap-c)#fa ? % Unrecognized command R7(config-pmap-c)#f exit R7(config-pmap)#class class-dea fault R7(config-pmap-c)#fa R7(config-pmap-c)#fair-queue            exit R7(config-pmap)#exit R7(config)#exit R7# *Mar 1 14:14:19.247: %SYS-5-CONFIG_I: Configured from console by console R7# RACK99AS>3 [Resuming connection 3 to r3 ... ] *M R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class-map match-all dscp12 R3(config-cmap)# match dscp af12 R3(config-cmap)#class-map match-all dscp14 R3(config-cmap)# match dscp af13 R3(config-cmap)#class-map match-all dscp26 R3(config-cmap)# match dscp af31 R3(config-cmap)#class-map match-all dscp28 R3(config-cmap)# match dscp af32 R3(config-cmap)#class-map match-all prec3 R3(config-cmap)# match ip precedence 3 R3(config-cmap)#policy-map test R3(config-pmap)# class dscp12 R3(config-pmap-c)# class dscp14 R3(config-pmap-c)# class dscp26 R3(config-pmap-c)# class dscp28 R3(config-pmap-c)# class prec3 R3(config-pmap-c)#interface FastEthernet0/0 R3(config-if)# service-policy input test R3(config-if)# R3(config-if)#^Z R3# *Mar 1 18:16:18.985: %SYS-5-CONFIG_I: Configured from console by console R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 5 packets, 490 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK99AS>5 [Resuming connection 5 to r5 ... ] 03: S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 5 packets, 570 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 11 packets, 1078 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK99AS>7 [Resuming connection 7 to r7 ... ] R7#sh run|    | b class class-map match-all S5Other match access-group name S5 class-map match-all S5Telnet match access-group name S5 match protocol telnet class-map match-any JPG match protocol http url "*.jpg" match protocol http url "*.jpe" match protocol http url "*.jpeg" match protocol http mime "*jpeg" match protocol http mime "*jpe" match protocol http mime "*jpg" ! ! policy-map Prob5 class JPG shape average 1000000 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 class class-default --More--  ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex service-policy output Prob5 ! interface Serial1/0 no ip address --More--   encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 --More--   no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! --More--  ip classless ! ip http server no ip http secure-server ! ip access-list standard S5 permit 208.28.1.2 ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pri R7(config)#prio R7(config)#priority-list ? <1-16> Priority list number R7(config)#priority-list 1 ? default Set priority queue for unspecified datagrams interface Establish priorities for packets from a named interface protocol priority queueing by protocol queue-limit Set queue limits for priority queues R7(config)#priority-list 1 pro R7(config)#priority-list 1 protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dlsw Data Link Switching (Direct encapsulation only) ip IP ipv6 IPV6 ipx Novell IPX llc2 llc2 pad PAD links pppoe PPP over Ethernet --More--   qllc qllc protocol rsrb Remote Source-Route Bridging snapshot Snapshot routing support stun Serial Tunnel R7(config)#priority-list 1 protocol ip ? high medium normal low R7(config)#priority-list 1 protocol ip high ? fragments Prioritize fragmented IP packets gt Prioritize packets greater than a specified size list To specify an access list lt Prioritize packets less than a specified size tcp Prioritize TCP packets 'to' or 'from' the specified port udp Prioritize UDP packets 'to' or 'from' the specified port R7(config)#priority-list 1 protocol ip high tcp ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   R7(config)#priority-list 1 protocol ip high tcp tel R7(config)#priority-list 1 protocol ip high tcp telnet R7(config)#priority-list 1 protocol ip high tcp telnet                   p R7(config)#priority-list 1 protocol ip lo R7(config)#priority-list 1 protocol ip low tcp ww R7(config)#priority-list 1 protocol ip low tcp www R7(config)#priority-list 1 protocol ip low tcp www                deg f R7(config)#priority-list 1 protocol defa R7(config)#priority-list 1 protocol defa    ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dlsw Data Link Switching (Direct encapsulation only) ip IP ipv6 IPV6 ipx Novell IPX llc2 llc2 pad PAD links pppoe PPP over Ethernet --More--   R7(config)#priority-list 1 protocol          de R7(config)#priority-list 1 default ? high medium normal low R7(config)#priority-list 1 default no R7(config)#priority-list 1 default normal ? R7(config)#priority-list 1 default normal R7(config)#do sh run |b prio sh run |b prio ^ % Invalid input detected at '^' marker. R7(config)#do sh run |b prio b prio ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address --More--   shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server ! --More--  ip access-list standard S5 permit 208.28.1.2 ! priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! --More--   R7(config)#do sh run | b priob prio priority-list 1 default normal        me R7(config)#priority-list 1 default medium R7(config)#priority-list 1 default medium do sh run | b prio   iority-li priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www priority-list 1 default medium ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R7(config)#do sh run | b priority-lipriority-list 1 default medium npriority-list 1 default medium opriority-list 1 default medium  priority-list 1 default medium  R7(config)#do sh pri % Ambiguous command: "sh pri" R7(config)#do sh prio sh prio ^ % Invalid input detected at '^' marker. R7(config)#do sh prio          int s 1/0.2 R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri? % Unrecognized command R7(config-subif)#pri   exit R7(config)#exitint s 1/0.2   R7(config-if)#pri R7(config-if)#priority-group 1 ? R7(config-if)#priority-group 1 R7(config-if)#^Z R7#de *Mar 1 14:23:59.782: %SYS-5-CONFIG_I: Configured from console by console R7#deb prio R7#deb priority Priority output queueing debugging is on R7# R7# R7# R7# *Mar 1 14:24:06.846: PQ: Serial1/0 output (Pk size/Q 84/0) *Mar 1 14:24:07.046: PQ: Serial1/0 output (Pk size/Q 84/0) R7# R7# R7# R7# *Mar 1 14:24:10.260: PQ: Serial1/0 output (Pk size/Q 13/0) R7#deb priority  ? R7#deb priority *Mar 1 14:24:17.063: PQ: Serial1/0 output (Pk size/Q 84/0) R7#deb priority               *Mar 1 14:24:20.260: PQ: Serial1/0 output (Pk size/Q 13/0) R7#180.40. *Mar 1 14:24:27.103: PQ: Serial1/0 output (Pk size/Q 84/0) R7#180.40.7.162 Trying 180.40.7.162 ... Open R2# *Mar 1 14:24:30.260: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:24:30.849: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:30.849: PQ: Serial1/0 output (Pk size/Q 48/0) *Mar 1 14:24:30.897: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:30.897: PQ: Serial1/0 output (Pk size/Q 44/0) *Mar 1 14:24:30.901: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:30.901: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:30.905: PQ: Serial1/0 output (Pk size/Q 56/0) *Mar 1 14:24:30.905: PQ: Serial1/0 output (Pk size/Q 44/0) *Mar 1 14:24:30.949: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:30.949: PQ: Serial1/0 output (Pk size/Q 47/0) *Mar 1 14:24:30.949: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:30.949: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:30.954: PQ: Serial1/0 output (Pk size/Q 47/0) *Mar 1 14:24:30.954: PQ: Serial1/0 output (Pk size/Q 53/0) *Mar 1 14:24:30.962: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:30.970: PQ: Serial1/0 output (Pk size/Q 47/0) *Mar 1 14:24:31.174: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:31.174: PQ: Serial1/0 output (Pk size/Q 44/0) *Mar 1 14:24:36.663: PQ: Serial1/0: cdp (defaulting) -> normal *Mar 1 14:24:36.663: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:24:36.663: PQ: Serial1/0: cdp (defaulting) -> normal *Mar 1 14:24:36.707: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:24:36.763: PQ: Serial1/0 output (Pk size/Q 84/0) *Mar 1 14:24:37.064: PQ: Serial1/0 output (Pk size/Q 84/0) *Mar 1 14:24:40.261: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:24:47.080: PQ: Serial1/0 output (Pk size/Q 84/0) *Mar 1 14:24:50.261: PQ: Serial1/0 output (Pk size/Q 13/0) R2# *Mar 1 14:24:52.252: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:52.252: PQ: Serial1/0 output (Pk size/Q 46/0) *Mar 1 14:24:52.497: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:52.497: PQ: Serial1/0 output (Pk size/Q 44/0)q [Connection to 180.40.7.162 closed by foreign host] R7# R7# *Mar 1 14:24:53.663: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:53.663: PQ: Serial1/0 output (Pk size/Q 45/0) *Mar 1 14:24:53.771: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:53.771: PQ: Serial1/0 output (Pk size/Q 46/0) *Mar 1 14:24:53.943: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:53.943: PQ: Serial1/0 output (Pk size/Q 44/0) *Mar 1 14:24:53.951: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:24:53.951: PQ: Serial1/0 output (Pk size/Q 44/0) R7#u akl   *Mar 1 14:24:57.096: PQ: Serial1/0 output (Pk size/Q 84/0) R7#u all All possible debugging has been turned off R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0 R7(config-if)#int s 1/0priority-group 1 npriority-group 1 opriority-group 1  priority-group 1  R7(config-if)#exit R7(config)#\ map R7(config)#map-cl R7(config)#map-class f R7(config)#map-class frame-relay Prob6 R7(config-map-class)#p? % Unrecognized command R7(config-map-class)#p fra R7(config-map-class)#frame-relay > ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 7000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R7(config-map-class)#frame-relay pri R7(config-map-class)#frame-relay priority-group 1 ? R7(config-map-class)#frame-relay priority-group 1 R7(config-map-class)#int fa 0/     s 1/0.2 R7(config-subif)#fram class Prob6 R7(config-subif)#do sh fram pvc 702 PVC Statistics for interface Serial1/0 (Frame Relay DTE) DLCI = 702, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.2 input pkts 2903 output pkts 2902 in bytes 485180 out bytes 485240 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 2598 out bcast bytes 453780 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 14:25:54, last time pvc status changed 14:25:54 R7(config-subif)# R7(config-subif)# R7(config-subif)# R7(config-subif)#do sh que R7(config-subif)#do sh que int s 1/0.2 sh que int s 1/0.2 ^ % Invalid input detected at '^' marker. R7(config-subif)#do sh que int s 1/0.2u int s 1/0.2e int s 1/0.2i int s 1/0.2n int s 1/0.2g int s 1/0.2 sh queueing int s 1/0.2 ^ % Invalid input detected at '^' marker. R7(config-subif)#do sh queueing int s 1/0.2                    fram int qu sh fram int qu ^ % Invalid input detected at '^' marker. R7(config-subif)#do sh fram int qu q qu  qu  qu ^Z sh fram qu ^ % Invalid input detected at '^' marker. R7#s *Mar 1 14:27:07.178: %SYS-5-CONFIG_I: Configured from console by console R7#sh fra R7#sh fram R7#sh frame-relay ? end-to-end Frame-relay end-to-end VC information fragment show frame relay fragmentation information ip show frame relay IP statistics lapf show frame relay lapf status/statistics lmi show frame relay lmi statistics map Frame-Relay map table multilink Show Multilink Frame Relay bundle information pvc show frame relay pvc statistics qos-autosense show frame relay qos-autosense information route show frame relay route svc show frame relay SVC stuff traffic Frame-Relay protocol statistics vc-bundle FR VC-Bundle vofr Show frame-relay VoFR statistics R7#sh frame-relay pvc ? interface <16-1022> DLCI | Output modifiers R7#sh frame-relay pvc  int ? % Unrecognized command R7#sh frame-relay pvcint       int ? BRI ISDN Basic Rate Interface Dialer Dialer interface MFR Multilink Frame Relay bundle interface Serial Serial Tunnel Tunnel interface R7#sh frame-relay pv int ser 1/0.2 ? <16-1022> DLCI | Output modifiers R7#sh frame-relay pv int ser 1/0.2 PVC Statistics for interface Serial1/0.2 (Frame Relay DTE) Active Inactive Deleted Static Local 2 0 0 0 Switched 0 0 0 0 Unused 0 1 0 0 DLCI = 702, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.2 input pkts 2907 output pkts 2906 in bytes 485804 out bytes 485864 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 2601 out bcast bytes 454304 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 14:27:07, last time pvc status changed 14:27:07 R7#confi gt ^ % Invalid input detected at '^' marker. R7#sh queu R7#sh queueing pri R7#sh queueing priority Current DLCI priority queue configuration: Current priority queue configuration: List Queue Args 1 high protocol ip tcp port telnet 1 low protocol ip tcp port www R7#confi g t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#it s1/     nt s 1/0 R7(config-if)#fram in R7(config-if)#fram in? interface-dlci interface-queue intf-type inverse-arp R7(config-if)#fram in R7(config-if)#fram int R7(config-if)#fram inter R7(config-if)#fram interface-q R7(config-if)#fram interface-queue ? priority enable PVC interface priority queueing R7(config-if)#fram interface-queue p R7(config-if)#fram interface-queue priority ? <1-1024> High limit R7(config-if)#fram interface-queue priority                               int s 1/0.2 R7(config-subif)#fra R7(config-subif)#fram R7(config-subif)#frame-relay ? class Define a map class on the interface de-group Associate a DE group with a DLCI interface-dlci Define a DLCI on an interface/subinterface inverse-arp Enable/disable FR inverse ARP ip Frame Relay Internet Protocol config commands map Map a protocol address to a DLCI address payload-compression Use payload compression priority-dlci-group Define a priority group of DLCIs vc-bundle configure a frame-relay vc-bundle R7(config-subif)#frame-relay             exit R7(config)#int s 1/0.  R7(config-if)#fram R7(config-if)#frame-relay ta raff R7(config-if)#frame-relay traffic-shaping R7(config-if)#^Z R7#shconfi t *Mar 1 14:29:09.174: %SYS-5-CONFIG_I: Configured from console by console R7#confi tsh queueing priority Current DLCI priority queue configuration: Current priority queue configuration: List Queue Args 1 high protocol ip tcp port telnet 1 low protocol ip tcp port www R7#sh queueing priority confi t sh queueing priority confi gt sh frame-relay pv int ser 1/0.2 PVC Statistics for interface Serial1/0.2 (Frame Relay DTE) Active Inactive Deleted Static Local 2 0 0 0 Switched 0 0 0 0 Unused 0 1 0 0 DLCI = 702, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.2 input pkts 2914 output pkts 2913 in bytes 486936 out bytes 486996 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 2607 out bcast bytes 455352 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 14:28:51, last time pvc status changed 14:28:51 R7#sh fram pvc 702 PVC Statistics for interface Serial1/0 (Frame Relay DTE) DLCI = 702, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.2 input pkts 2914 output pkts 2913 in bytes 486936 out bytes 486996 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 2607 out bcast bytes 455352 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 14:29:02, last time pvc status changed 14:29:02 cir 56000 bc 7000 be 0 byte limit 875 interval 125 mincir 28000 byte increment 875 Adaptive Shaping none pkts 0 bytes 0 pkts delayed 0 bytes delayed 0 shaping inactive traffic shaping drops 0 Queueing strategy: priority-list 1 List Queue Args 1 high protocol ip tcp port telnet --More--   List Queue Args 1 low protocol ip tcp port www Output queue: high 0/20/0, medium 0/40/0, normal 0/60/0, low 0/80/0 R7#deb prio R7#deb priority Priority output queueing debugging is on R7# R7# R7# R7#180.40.7.162 Trying 180.40.7.162 ... Open R2# R2# R2# R2# R2# R2# R2# R2# R2#q [Connection to 180.40.7.162 closed by foreign host] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int s 1/0 R7(config-if)#fram R7(config-if)#frame-relay inter R7(config-if)#frame-relay interface-q R7(config-if)#frame-relay interface-queue ? priority enable PVC interface priority queueing R7(config-if)#frame-relay interface-queue per  ri R7(config-if)#frame-relay interface-queue priority ? <1-1024> High limit R7(config-if)#frame-relay interface-queue priority R7(config-if)# R7(config-if)#^Z R7# R7# R7# *Mar 1 14:30:43.817: %SYS-5-CONFIG_I: Configured from console by console R7#confi t180.40.7.162 Trying 180.40.7.162 ... Open R2# *Mar 1 14:30:47.234: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.234: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:30:47.651: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.651: PQ: Serial1/0 output (Pk size/Q 48/2) *Mar 1 14:30:47.699: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.699: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:30:47.699: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.703: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.703: PQ: Serial1/0 output (Pk size/Q 56/2) *Mar 1 14:30:47.703: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:30:47.747: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.751: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:30:47.751: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.751: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.755: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:30:47.755: PQ: Serial1/0 output (Pk size/Q 53/2) *Mar 1 14:30:47.763: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.767: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:30:47.976: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:47.976: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:30:50.275: PQ: Serial1/0 output (Pk size/Q 13/0) R2# R2# *Mar 1 14:30:54.811: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:54.811: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:30:55.055: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:55.055: PQ: Serial1/0 output (Pk size/Q 44/2) R2# R2# *Mar 1 14:30:55.929: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:55.929: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:30:56.145: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:56.145: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:30:56.329: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:56.329: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:30:56.574: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:56.574: PQ: Serial1/0 output (Pk size/Q 44/2) R2# R2#q *Mar 1 14:30:57.207: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:57.207: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:30:57.251: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:57.251: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:30:57.451: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:57.451: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:30:57.519: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:57.519: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:30:57.768: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:57.768: PQ: Serial1/0 output (Pk size/Q 44/2) [Connection to 180.40.7.162 closed by foreign host] R7# *Mar 1 14:30:58.954: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:58.954: PQ: Serial1/0 output (Pk size/Q 45/2) *Mar 1 14:30:59.066: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:59.066: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:30:59.214: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:59.214: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:30:59.238: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:59.238: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:30:59.238: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:30:59.242: PQ: Serial1/0 output (Pk size/Q 44/2) R7# *Mar 1 14:31:00.276: PQ: Serial1/0 output (Pk size/Q 13/0) R7# R7# R7# *Mar 1 14:31:01.574: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:31:01.574: PQ: Serial1/0 output (Pk size/Q 136/2) *Mar 1 14:31:01.658: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:01.658: PQ: Serial1/0 output (Pk size/Q 136/2) R7#1809  *Mar 1 14:31:06.867: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:31:06.867: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:31:07.167: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:07.167: PQ: Serial1/0 output (Pk size/Q 84/2) R7#180 0.40.7. *Mar 1 14:31:10.276: PQ: Serial1/0 output (Pk size/Q 13/0) R7#180.40.7.66 Trying 180.40.7.66 ... Open R3# R3# *Mar 1 14:31:13.029: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:13.029: PQ: Serial1/0 output (Pk size/Q 48/2) *Mar 1 14:31:13.061: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:13.061: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:31:13.061: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:13.065: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:13.065: PQ: Serial1/0 output (Pk size/Q 56/2) *Mar 1 14:31:13.065: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:31:13.109: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:13.109: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:31:13.109: PQ: Serial1/0 dlci 703 -> normal R3# R3# *Mar 1 14:31:13.113: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:13.113: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:31:13.113: PQ: Serial1/0 output (Pk size/Q 53/2) *Mar 1 14:31:13.117: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:13.117: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:31:13.333: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:13.333: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:31:14.042: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:14.042: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:31:14.219: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:14.219: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:31:14.387: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:14.387: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:31:14.603: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:14.603: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:31:17.207: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:17.207: PQ: Serial1/0 output (Pk size/Q 84/2)u *Mar 1 14:31:20.276: PQ: Serial1/0 output (Pk size/Q 13/0) q *Mar 1 14:31:21.659: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:21.659: PQ: Serial1/0 output (Pk size/Q 45/2) *Mar 1 14:31:21.871: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:21.871: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:31:22.196: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:22.196: PQ: Serial1/0 output (Pk size/Q 45/2) *Mar 1 14:31:22.396: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:22.396: PQ: Serial1/0 output (Pk size/Q 45/2) *Mar 1 14:31:22.612: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:22.612: PQ: Serial1/0 output (Pk size/Q 44/2) [Connection to 180.40.7.66 closed by foreign host] R7# R7# *Mar 1 14:31:23.029: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:23.029: PQ: Serial1/0 output (Pk size/Q 45/2) *Mar 1 14:31:23.213: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:23.213: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:31:23.354: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:23.354: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:31:23.358: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:23.358: PQ: Serial1/0 output (Pk size/Q 44/2) R7# *Mar 1 14:31:27.240: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:31:27.240: PQ: Serial1/0 output (Pk size/Q 84/2) R7# *Mar 1 14:31:30.277: PQ: Serial1/0 output (Pk size/Q 13/0) R7# R7# R7#u all All possible debugging has been turned off R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int s 1/0 R7(config-if)#int s 1/0frame-relay interface-queue priority nframe-relay interface-queue priority oframe-relay interface-queue priority  frame-relay interface-queue priority  R7(config-if)#^Z R7# *Mar 1 14:31:57.373: %SYS-5-CONFIG_I: Configured from console by console R7# R7# R7# R7# R7# R7# R7# RACK99AS>2 [Resuming connection 2 to r2 ... ] * R2#ping Protocol [ip]: Target IP address: 180.40.7.161 Repeat count [5]: 10000000 Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 10000000, 100-byte ICMP Echos to 180.40.7.161, timeout is 2 seconds: !!!!!!!!!!!!!!!! RACK99AS>7 [Resuming connection 7 to r7 ... ] R7#deb pol ^ % Invalid input detected at '^' marker. R7#deb pol  r i ri R7#deb pri % Ambiguous command: "deb pri" R7#deb prio R7#deb priority Priority output queueing debugging is on R7#deb priority  olconfi tu all 180.40.7.66162 Trying 180.40.7.162 ... Open R2# R2# R2# R2# R2#q [Connection to 180.40.7.162 closed by foreign host] R7#sh run int s 1/0/.  .2 Building configuration... Current configuration : 182 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay class Prob6 frame-relay interface-dlci 702 end R7#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 14:32:11, FastEthernet0/1 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.162, 14:32:11, Serial1/0.2 [110/792] via 180.40.7.67, 14:32:11, Serial1/0.1 O 20.10.1.0 [110/782] via 180.40.7.162, 14:32:11, Serial1/0.2 [110/782] via 180.40.7.67, 14:32:11, Serial1/0.1 C 208.28.1.0/24 is directly connected, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 5 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/1 O 180.40.7.162/32 [110/781] via 180.40.7.162, 14:32:12, Serial1/0.2 [110/781] via 180.40.7.67, 14:32:12, Serial1/0.1 C 180.40.7.160/27 is directly connected, Serial1/0.2 --More--  O 180.40.7.0/27 [110/782] via 180.40.7.129, 14:32:19, FastEthernet0/1 C 180.40.7.64/27 is directly connected, Serial1/0.1 R7#sh run int s           s   run int s 1/0.2 Building configuration... Current configuration : 182 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay class Prob6 frame-relay interface-dlci 702 end R7#confi g t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int s 1/0.2 R7(config-subif)#no ip ospf network point-to-multipoint R7(config-subif)#^Z R7# *Mar 1 14:34:23.200: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7# RACK99AS>2 [Resuming connection 2 to r2 ... ] !!!!!!!!!!!! !!!!!!!!!!!!!!!!!. Success rate is 99 percent (1417/1418), round-trip min/avg/max = 84/87/269 ms R2#x config  t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.2 R2(config-subif)#do sh run int s 1/0.2 Building configuration... Current configuration : 199 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob3 end R2(config-subif)#no network         ip ospf network point-to-multipoint R2(config-subif)# R2(config-subif)#^Z R2# *Mar 1 18:35:39.796: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R2# *Mar 1 18:35:41.122: RACK99AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#deb ip pol  ri R7#deb ip prio R7#deb ip prio ^ % Invalid input detected at '^' marker. R7#deb ip prioprio rio prio  Priority output queueing debugging is on R7# R7# R7# R7#deb prioip prioconfi t sh run int s 1/0.2ip route run int s 1/0.2180.40.7.162  Trying 180.40.7.162 ... Open R2# R2# R2# R2# RACK99AS>2 [Resuming connection 2 to r2 ... ] %SYS-5-CONFIG_I: Configured from console by console R2# R2#confi t1000000080.40.7.161ping  Protocol [ip]: Target IP address: pingconfi t1000000080.40.7.161 Repeat count [5]: 10000000~ % A decimal number between 1 and 2147483647. Repeat count [5]: 10000000~ ~ 80.40.7.161 % A decimal number between 1 and 2147483647. Repeat count [5]: 180.40.7.161 10000000 Datagram size [100]: 10000000 % A decimal number between 36 and 18024. Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: 10000000  Type escape sequence to abort. Sending 10000000, 100-byte ICMP Echos to 180.40.7.161, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!! RACK99AS>7 [Resuming connection 7 to r7 ... ] R2# R2# R2# R2# R2# RACK99AS>2 [Resuming connection 2 to r2 ... ] !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!. Success rate is 99 percent (331/332), round-trip min/avg/max = 56/58/157 ms R2#q R2 con0 is now available Press RETURN to get started. R2> R2> R2> R2>en R2# R2# RACK99AS>7 [Resuming connection 7 to r7 ... ] R2#q [Connection to 180.40.7.162 closed by foreign host] R7#u all All possible debugging has been turned off R7# R7# R7# R7# R7#sh run |b    b 1/0 interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 frame-relay class Prob6 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 --More--   no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! --More--  router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server ! ip access-list standard S5 permit 208.28.1.2 ! ! map-class frame-relay Prob6 frame-relay priority-group 1 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! ! ! ! ! --More--   R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int s 1/0 R7(config-if)#no fram R7(config-if)#no frame-relay traff R7(config-if)#int s 1/0.2 R7(config-subif)#no fram R7(config-subif)#no frame-relay class Prob6 R7(config-subif)#fram R7(config-subif)#frame-relay ? class Define a map class on the interface de-group Associate a DE group with a DLCI interface-dlci Define a DLCI on an interface/subinterface inverse-arp Enable/disable FR inverse ARP ip Frame Relay Internet Protocol config commands map Map a protocol address to a DLCI address payload-compression Use payload compression priority-dlci-group Define a priority group of DLCIs vc-bundle configure a frame-relay vc-bundle R7(config-subif)#frame-relay in R7(config-subif)#frame-relay inter R7(config-subif)#frame-relay interface-dlci                   pri R7(config-subif)#frame-rela priority-dlci-group ? <1-16> Assign priority group R7(config-subif)#frame-rela priority-dlci-group 1 ? <16-1007> DLCI for high priority R7(config-subif)#frame-rela priority-dlci-group 1 702 ? <16-1007> DLCI for medium priority R7(config-subif)#frame-rela priority-dlci-group 1 702 R7(config-subif)# *Mar 1 14:39:11.068: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-subif)#^Z R7# *Mar 1 14:39:21.461: %SYS-5-CONFIG_I: Configured from console by console R7# R7# R7# R7# R7# R7# R7# R7# R7# R7# R7# R7# R7#deb prio *Mar 1 14:39:40.384: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7#deb prio R7#deb priority Priority output queueing debugging is on R7# R7# R7# R7#deb priority confi t sh run | b 1/0u all 180.40.7.162 Trying 180.40.7.162 ... Open R2# *Mar 1 14:39:47.873: PQ: Serial1/0: ip -> normal *Mar 1 14:39:47.913: PQ: Serial1/0: ip -> normal *Mar 1 14:39:47.913: PQ: Serial1/0: ip -> normal *Mar 1 14:39:47.913: PQ: Serial1/0: ip -> normal *Mar 1 14:39:47.953: PQ: Serial1/0: ip -> normal *Mar 1 14:39:47.957: PQ: Serial1/0: ip -> normal *Mar 1 14:39:47.957: PQ: Serial1/0: ip -> normal *Mar 1 14:39:47.969: PQ: Serial1/0: ip -> normal *Mar 1 14:39:48.173: PQ: Serial1/0: ip -> normal R2# R2# R2# R2# *Mar 1 14:39:49.599: PQ: Serial1/0: ip -> normal *Mar 1 14:39:49.820: PQ: Serial1/0: ip -> normal *Mar 1 14:39:49.984: PQ: Serial1/0: ip -> normal *Mar 1 14:39:50.152: PQ: Serial1/0: ip -> normal *Mar 1 14:39:50.377: PQ: Serial1/0: ip -> normal *Mar 1 14:39:50.381: PQ: Serial1/0: ip -> normalping *Mar 1 14:39:59.003: PQ: Serial1/0: ip -> normal *Mar 1 14:39:59.231: PQ: Serial1/0: ip -> normal *Mar 1 14:39:59.664: PQ: Serial1/0: ip -> normal *Mar 1 14:39:59.816: PQ: Serial1/0: ip -> normal *Mar 1 14:39:59.944: PQ: Serial1/0: ip -> normal *Mar 1 14:40:00.061: PQ: Serial1/0: ip -> normal *Mar 1 14:40:00.289: PQ: Serial1/0: ip -> normal *Mar 1 14:40:00.377: PQ: Serial1/0: ip -> normal180. *Mar 1 14:40:02.044: PQ: Serial1/0: ip -> normal *Mar 1 14:40:02.168: PQ: Serial1/0: ip -> normal *Mar 1 14:40:02.316: PQ: Serial1/0: ip -> normal *Mar 1 14:40:02.545: PQ: Serial1/0: ip -> normal *Mar 1 14:40:02.553: PQ: Serial1/0: ip -> normal *Mar 1 14:40:02.785: PQ: Serial1/0: ip -> normal40.7. *Mar 1 14:40:03.654: PQ: Serial1/0: ip -> normal *Mar 1 14:40:03.743: PQ: Serial1/0: ip -> normal *Mar 1 14:40:03.971: PQ: Serial1/0: ip -> normal *Mar 1 14:40:03.979: PQ: Serial1/0: ip -> normal *Mar 1 14:40:04.155: PQ: Serial1/0: ip -> normal *Mar 1 14:40:04.348: PQ: Serial1/0: ip -> normal *Mar 1 14:40:04.580: PQ: Serial1/0: ip -> normal1 61 *Mar 1 14:40:06.587: PQ: Serial1/0: ip -> normal *Mar 1 14:40:06.820: PQ: Serial1/0: ip -> normal *Mar 1 14:40:07.324: PQ: Serial1/0: ip -> normal *Mar 1 14:40:07.553: PQ: Serial1/0: ip -> normal *Mar 1 14:40:07.577: PQ: Serial1/0: ip -> normal *Mar 1 14:40:07.721: PQ: Serial1/0: ip -> normal *Mar 1 14:40:07.950: PQ: Serial1/0: ip -> normal *Mar 1 14:40:09.047: PQ: Serial1/0: ip -> normal *Mar 1 14:40:09.280: PQ: Serial1/0: ip -> normalrep 100 *Mar 1 14:40:10.157: PQ: Serial1/0: ip -> normal *Mar 1 14:40:10.213: PQ: Serial1/0: ip -> normal *Mar 1 14:40:10.377: PQ: Serial1/0: ip -> normal *Mar 1 14:40:10.446: PQ: Serial1/0: ip -> normal *Mar 1 14:40:10.446: PQ: Serial1/0: ip -> normal *Mar 1 14:40:10.590: PQ: Serial1/0: ip -> normal *Mar 1 14:40:10.822: PQ: Serial1/0: ip -> normal0000 *Mar 1 14:40:11.347: PQ: Serial1/0: ip -> normal *Mar 1 14:40:11.515: PQ: Serial1/0: ip -> normal *Mar 1 14:40:11.700: PQ: Serial1/0: ip -> normal *Mar 1 14:40:11.932: PQ: Serial1/0: ip -> normal Type escape sequence to abort. Sending 1000000, 100-byte ICMP Echos to 180.40.7.61, timeout is 2 seconds: *Mar 1 14:40:12.449: PQ: Serial1/0: ip -> normal *Mar 1 14:40:12.621: PQ: Serial1/0: ip -> normal *Mar 1 14:40:12.761: PQ: Serial1/0: ip -> normal *Mar 1 14:40:12.930: PQ: Serial1/0: ip -> normal *Mar 1 14:40:13.158: PQ: Serial1/0: ip -> normal *Mar 1 14:40:13.318: PQ: Serial1/0: ip -> normal *Mar 1 14:40:13.547: PQ: Serial1/0: ip -> normal. *Mar 1 14:40:15.566: PQ: Serial1/0: ip -> normal. *Mar 1 14:40:17.569: PQ: Serial1/0: ip -> normal. *Mar 1 14:40:19.573: PQ: Serial1/0: ip -> normal *Mar 1 14:40:20.378: PQ: Serial1/0: ip -> normal. R7# *Mar 1 14:40:21.480: PQ: Serial1/0: ip -> normal R7# *Mar 1 14:40:23.575: PQ: Serial1/0: ip -> normal R7#u all    *Mar 1 14:40:25.578: PQ: Serial1/0: ip -> normal R7#u   q (You have open connections) [confirm] Closing: 180.40.7.162 ! R7 con0 is now available Press RETURN to get started. *Mar 1 14:40:27.582: PQ: Serial1/0: ip -> normal *Mar 1 14:40:28.651: PQ: Serial1/0: ip -> normal *Mar 1 14:40:28.784: PQ: Serial1/0: ip -> normal *Mar 1 14:40:28.788: PQ: Serial1/0: ip -> normal *Mar 1 14:40:30.378: PQ: Serial1/0: ip -> normal R7> R7> R7>en R7#u all All possible debugging has been turned off R7# R7# R7# R7# RACK99AS>2 [Resuming connection 2 to r2 ... ] * R2#en ping Protocol [ip]: Target IP address: 180.40.7.161 Repeat count [5]: 100000 Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 100000, 100-byte ICMP Echos to 180.40.7.161, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!! RACK99AS>7 [Resuming connection 7 to r7 ... ] R7#180.40.7.162 Trying 180.40.7.162 ... Open R2#x  R7#deb prio Priority output queueing debugging is on R7# [Resuming connection 1 to 180.40.7.162 ... ] R2# *Mar 1 14:41:13.200: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.261: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.321: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.381: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.437: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.497: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.557: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.613: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.673: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.733: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.793: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.850: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.866: PQ: Serial1/0: ip -> normal R2# R2# R2# R2# *Mar 1 14:41:13.910: PQ: Serial1/0: ip -> normal *Mar 1 14:41:13.970: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.030: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.042: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.086: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.146: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.206: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.210: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.266: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.326: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.386: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.443: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.475: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.503: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.563: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.623: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.679: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.739: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.755: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.799: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.859: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.915: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.935: PQ: Serial1/0: ip -> normal *Mar 1 14:41:14.975: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.035: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.096: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.104: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.152: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.216: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.276: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.336: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.360: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.392: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.452: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.512: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.572: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.656: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.717: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.777: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.833: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.893: PQ: Serial1/0: ip -> normal *Mar 1 14:41:15.953: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.009: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.069: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.129: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.189: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.245: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.306: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.366: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.426: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.482: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.542: PQ: Serial1/0: ip -> normal R2# R2# *Mar 1 14:41:16.602: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.662: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.718: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.778: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.838: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.899: PQ: Serial1/0: ip -> normal *Mar 1 14:41:16.955: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.015: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.075: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.135: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.191: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.251: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.311: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.371: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.431: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.487: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.532: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.548: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.608: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.668: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.676: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.724: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.784: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.844: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.904: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.932: PQ: Serial1/0: ip -> normal *Mar 1 14:41:17.960: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.020: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.080: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.141: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.197: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.257: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.317: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.377: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.437: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.493: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.553: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.613: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.673: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.730: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.790: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.850: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.906: PQ: Serial1/0: ip -> normal *Mar 1 14:41:18.966: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.026: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.086: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.142: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.202: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.262: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.323: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.379: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.439: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.499: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.559: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.615: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.675: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.735: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.795: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.851: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.911: PQ: Serial1/0: ip -> normal *Mar 1 14:41:19.972: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.032: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.088: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.148: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.208: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.268: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.324: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.380: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.384: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.444: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.504: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.561: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.621: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.681: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.749: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.809: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.869: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.925: PQ: Serial1/0: ip -> normal *Mar 1 14:41:20.985: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.045: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.105: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.162: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.222: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.282: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.338: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.398: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.458: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.518: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.574: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.634: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.694: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.754: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.811: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.871: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.931: PQ: Serial1/0: ip -> normal *Mar 1 14:41:21.991: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.047: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.107: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.167: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.223: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.283: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.343: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.404: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.460: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.520: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.580: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.640: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.696: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.756: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.816: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.876: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.932: PQ: Serial1/0: ip -> normal *Mar 1 14:41:22.993: PQ: Serial1/0: ip -> normal *Mar 1 14:41:23.053: PQ: Serial1/0: ip -> normal *Mar 1 14:41:23.109: PQ: Se RACK99AS> [Resuming connection 7 to r7 ... ] 1:23.289: PQ: Serial1/0: ip -> normal *Mar 1 14:41:23.345: PQ: Serial1/0: ip -> normal *Mar 1 14:41:23.405: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.120: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.176: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.236: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.300: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.360: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.416: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.477: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.537: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.597: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.653: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.713: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.773: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.833: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.889: PQ: Serial1/0: ip -> normal *Mar 1 14:41:25.949: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.009: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.070: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.126: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.186: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.246: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.310: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.370: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.426: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.486: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.546: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.602: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.663: PQ: Serial1/0: R2# R2# R2#ip -> normal *Mar 1 14:41:26.723: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.783: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.839: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.899: PQ: Serial1/0: ip -> normal *Mar 1 14:41:26.959: PQ: Serial1/0: ip -> normal *Mar 1 14:41:27.019: PQ: Serial1/0: ip -> normal *Mar 1 14 R7#*Mar 1 14:41:27.568: PQ: Serial1/0: ip -> normal *Mar 1 14:41:27.628: PQ: Serial1/0: ip -> normal *Mar 1 14:41:27.684: PQ: Serial1/0: ip -> normal *Mar 1 14:41:27.744: PQ: Serial1/0: ip -> normal *Mar 1 14:41:27.772: PQ: Serial1/0: ip -> normal *Mar 1 14:41:27.804: PQ: Serial1/0: ip -> normal *Mar 1 14:41:27.865: PQ: Serial1/0: ip -> normal *Mar 1 14:41:27.921: PQ: Serial1/0: ip -> normal *Mar 1 14:41:27.981: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.041: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.101: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.157: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.217: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.277: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.353: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.413: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.474: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.534: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.594: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.654: PQ: Seri R7#al1/0: ip -> normal *Mar 1 14:41:28.714: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.774: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.834: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.862: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.894: PQ: Serial1/0: ip -> normal *Mar 1 14:41:28.950: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.010: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.070: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.131: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.191: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.251: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.311: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.375: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.435: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.491: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.551: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.611: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.671: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.732: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.792: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.852: PQ: Serial1/0: ip -> normal *Mar 1 14:41:29.912: PQ: Serial1/0: ip -> norma RACK99AS>2 [Resuming connection 2 to r2 ... ] !!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!. Success rate is 99 percent (647/648), round-trip min/avg/max = 56/59/152 ms R2# RACK99AS>7 [Resuming connection 7 to r7 ... ] Q: Serial1/0: ip -> normal *Mar 1 14:41:30.032: PQ: Serial1/0: ip -> normal *Mar 1 14:41:30.092: PQ: Serial1/0: ip -> normal *Mar 1 14:41:30.152: PQ: Serial1/0: ip -> normal *Mar 1 14:41:30.21 [Resuming connection 1 to 180.40.7.162 ... ] R2# R2# *Mar 1 14:41:36.611: PQ: Serial1/0: cdp -> normal *Mar 1 14:41:36.611: PQ: Serial1/0: cdp -> normal *Mar 1 14:41:36.955: PQ: Serial1/0: ip -> normal R2#q [Connection to 180.40.7.162 closed by foreign host] R7# *Mar 1 14:41:37.961: PQ: Serial1/0: ip -> normal *Mar 1 14:41:38.141: PQ: Serial1/0: ip -> normal *Mar 1 14:41:38.374: PQ: Serial1/0: ip -> normal *Mar 1 14:41:38.494: PQ: Serial1/0: ip -> normal *Mar 1 14:41:38.722: PQ: Serial1/0: ip -> normal R7# *Mar 1 14:41:39.111: PQ: Serial1/0: ip -> normal *Mar 1 14:41:39.199: PQ: Serial1/0: ip -> normal *Mar 1 14:41:39.347: PQ: Serial1/0: ip -> normal *Mar 1 14:41:39.351: PQ: Serial1/0: ip -> normal *Mar 1 14:41:39.355: PQ: Serial1/0: ip -> normal *Mar 1 14:41:39.375: PQ: Serial1/0: ip -> normal R7# *Mar 1 14:41:40.397: PQ: Serial1/0: ip -> normal R7# *Mar 1 14:41:50.397: PQ: Serial1/0: ip -> normal R7# *Mar 1 14:42:00.398: PQ: Serial1/0: ip -> normal R7# *Mar 1 14:42:10.398: PQ: Serial1/0: ip -> normal R7# R7# R7# R7# R7#sh ip *Mar 1 14:42:20.399: PQ: Serial1/0: ip -> normal R7#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:02:36, FastEthernet0/1 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.67, 00:02:36, Serial1/0.1 [110/792] via 180.40.7.162, 00:02:36, Serial1/0.2 O 20.10.1.0 [110/782] via 180.40.7.67, 00:02:36, Serial1/0.1 [110/782] via 180.40.7.162, 00:02:36, Serial1/0.2 C 208.28.1.0/24 is directly connected, FastEthernet0/0 180.40.0.0/27 is subnetted, 4 subnets C 180.40.7.128 is directly connected, FastEthernet0/1 C 180.40.7.160 is directly connected, Serial1/0.2 O 180.40.7.0 [110/782] via 180.40.7.129, 00:02:37, FastEthernet0/1 C 180.40.7.64 is directly connected, Serial1/0.1 R7#   confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int *Mar 1 14:42:30.399: PQ: Serial1/0: ip -> normal R7(config)#int s 1/0 R7(config-if)# *Mar 1 14:42:36.613: PQ: Serial1/0: cdp -> normal *Mar 1 14:42:36.613: PQ: Serial1/0: cdp -> normal R7(config-if)# *Mar 1 14:42:40.399: PQ: Serial1/0: ip -> normal R7(config-if)# *Mar 1 14:42:50.400: PQ: Serial1/0: ip -> normal R7(config-if)#fram R7(config-if)#frame-relay inter R7(config-if)#frame-relay interface-q R7(config-if)#frame-relay interface-queue p R7(config-if)#frame-relay interface-queue priority *Mar 1 14:43:00.400: PQ: Serial1/0: ip -> normal R7(config-if)#frame-relay interface-queue priority ? <1-1024> High limit R7(config-if)#frame-relay interface-queue priority R7(config-if)#^Z R7# R7# R7# *Mar 1 14:43:04.222: %SYS-5-CONFIG_I: Configured from console by console R7#confi tsh ip routedeb prio  *Mar 1 14:43:07.340: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:43:07.340: PQ: Serial1/0 output (Pk size/Q 84/2) R7#deb prio180.40.7.162 Trying 180.40.7.162 ... Open R2# *Mar 1 14:43:09.940: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:09.940: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:09.940: PQ: Serial1/0 output (Pk size/Q 48/2) *Mar 1 14:43:09.976: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:09.976: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:09.980: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:43:09.980: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:09.980: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:09.980: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:09.980: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:09.984: PQ: Serial1/0 output (Pk size/Q 56/2) *Mar 1 14:43:09.984: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:43:10.020: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:10.020: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:10.020: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:43:10.024: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:10.024: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:10.024: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:10.024: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:10.028: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:43:10.028: PQ: Serial1/0 output (Pk size/Q 53/2) *Mar 1 14:43:10.036: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:10.036: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:10.040: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:43:10.244: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:10.244: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:10.244: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:43:10.365: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:43:10.401: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:43:10.445: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:10.445: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:43:17.256: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:43:17.256: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:43:20.365: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:43:20.401: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:43:20.461: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:20.461: PQ: Serial1/0 output (Pk size/Q 84/2)q [Connection to 180.40.7.162 closed by foreign host] R7# *Mar 1 14:43:23.775: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:23.779: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:23.779: PQ: Serial1/0 output (Pk size/Q 45/2) *Mar 1 14:43:23.883: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:23.883: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:23.883: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:43:24.027: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:24.027: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:24.027: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:43:24.035: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:24.035: PQ: Serial1/0 dlci 702 -> normal R7#u *Mar 1 14:43:24.039: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:43:24.039: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:43:24.039: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:43:24.043: PQ: Serial1/0 output (Pk size/Q 44/2) R7#u all All possible debugging has been turned off R7# R7# R7# R7# R7#sh run | b inter R7#sh run | b inter     1/0 interface Serial1/0 no ip address encapsulation frame-relay frame-relay interface-queue priority ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address --More--   R7#deb prio Priority output queueing debugging is on R7#deb priosh run | b 1/0u all 180.40.7.162   6 *Mar 1 14:44:07.426: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:07.426: PQ: Serial1/0 output (Pk size/Q 84/2) R7#180.40.7.66 Trying 180.40.7.66 ... Open R3# *Mar 1 14:44:09.642: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:09.642: PQ: Serial1/0 output (Pk size/Q 48/2) *Mar 1 14:44:09.674: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:09.674: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:44:09.674: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:09.678: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:09.678: PQ: Serial1/0 output (Pk size/Q 56/2) *Mar 1 14:44:09.678: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:44:09.714: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:09.714: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:44:09.714: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:09.718: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:44:09.718: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:09.718: PQ: Serial1/0 output (Pk size/Q 53/2) *Mar 1 14:44:09.722: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:09.722: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:44:09.930: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:09.930: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:44:10.539: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:44:10.539: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:44:10.543: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:44:10.543: PQ: Serial1/0 output (Pk size/Q 84/2) R3# R3# R3# R3# *Mar 1 14:44:13.091: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:13.091: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:44:13.252: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:13.252: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:44:13.396: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:13.396: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:44:13.528: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:13.528: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:44:13.744: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:13.744: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:44:17.354: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:17.354: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:44:20.540: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:44:20.540: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:44:20.560: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:44:20.560: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:44:27.371: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:27.371: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:44:30.540: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:44:30.540: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:44:30.576: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:44:30.576: PQ: Serial1/0 output (Pk size/Q 84/2) R3# R3# R3# *Mar 1 14:44:34.871: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:34.871: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:44:35.075: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:35.075: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:44:35.204: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:35.204: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:44:35.420: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:35.420: PQ: Serial1/0 output (Pk size/Q 44/2)q [Connection to 180.40.7.66 closed by foreign host] R7# *Mar 1 14:44:36.730: PQ: Serial1/0: cdp (defaulting) -> normal *Mar 1 14:44:36.730: PQ: Serial1/0: cdp (defaulting) -> normal *Mar 1 14:44:36.786: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:36.786: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:44:36.786: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:44:36.830: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:44:36.958: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:36.958: PQ: Serial1/0 output (Pk size/Q 45/2) *Mar 1 14:44:37.059: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:37.063: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:44:37.195: PQ: Serial1/0 dlci 703 -> normal R7# *Mar 1 14:44:37.195: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:44:37.199: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:37.199: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:44:37.203: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:37.203: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:44:37.219: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:37.219: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:44:37.387: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:37.387: PQ: Serial1/0 output (Pk size/Q 84/2) R7# R7# R7# R7# *Mar 1 14:44:40.540: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:44:40.540: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:44:40.596: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:44:40.596: PQ: Serial1/0 output (Pk size/Q 84/2) R7#180.40.7.129 Trying 180.40.7.129 ... Open R3# R3# R3# R3# *Mar 1 14:44:47.408: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:47.408: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:44:50.541: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:44:50.541: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:44:50.613: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:44:50.613: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:44:57.360: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:44:57.360: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:45:00.541: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:45:00.541: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:45:00.569: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:45:00.569: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:45:07.424: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:45:07.424: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:45:10.542: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:45:10.542: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:45:10.630: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:45:10.630: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:45:17.341: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:45:17.341: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:45:20.542: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:45:20.542: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:45:20.546: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:45:20.546: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:45:27.357: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:45:27.357: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:45:30.542: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:45:30.542: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:45:30.562: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:45:30.562: PQ: Serial1/0 output (Pk size/Q 84/2) R3# R3# R3#q *Mar 1 14:45:36.732: PQ: Serial1/0: cdp (defaulting) -> normal *Mar 1 14:45:36.732: PQ: Serial1/0: cdp (defaulting) -> normal *Mar 1 14:45:36.773: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:45:36.773: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:45:36.773: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:45:36.817: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:45:37.374: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:45:37.374: PQ: Serial1/0 output (Pk size/Q 84/2) [Connection to 180.40.7.129 closed by foreign host] R7# R7#u all All possible debugging has been turned off R7# R7# R7# *Mar 1 14:45:40.543: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:45:40.543: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:45:40.579: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:45:40.579: PQ: Serial1/0 output (Pk size/Q 84/2) R7#sh run | b 1/0 interface Serial1/0 no ip address encapsulation frame-relay frame-relay interface-queue priority ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address --More--   R7#confi g ^ % Invalid input detected at '^' marker. R7#confi g t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0 R7(config-if)# frame-relay priority-dlci-group 1 702 702 702 702 R7(config-if)# R7(config-if)# R7(config-if)# *Mar 1 14:46:59.957: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Dead timer expired R7(config-if)#do sh fram pvc PVC Statistics for interface Serial1/0 (Frame Relay DTE) Active Inactive Deleted Static Local 2 0 0 0 Switched 0 0 0 0 Unused 0 1 0 0 DLCI = 701, DLCI USAGE = UNUSED, PVC STATUS = INACTIVE, INTERFACE = Serial1/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 14:46:41, last time pvc status changed 14:46:41 --More--   DLCI = 702, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 5598 output pkts 4171 in bytes 760827 out bytes 612542 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 2550 out DE pkts 0 out bcast pkts 2718 out bcast bytes 470716 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 14:46:53, last time pvc status changed 14:46:53 Priority DLCI Group 1, DLCI 702 (HIGH), DLCI 702 (MEDIUM) DLCI 702 (NORMAL), DLCI 702 (LOW) --More--   R7(config-if)#do sh fram pvc frame-relay priority-dlci-group 1 702 702 702 702n frame-relay priority-dlci-group 1 702 702 702 702o frame-relay priority-dlci-group 1 702 702 702 702 frame-relay priority-dlci-group 1 702 702 702 702 R7(config-if)#^Z R7#confi tg *Mar 1 14:48:04.547: %SYS-5-CONFIG_I: Configured from console by console R7#confi gt sh fram pvc 702 PVC Statistics for interface Serial1/0 (Frame Relay DTE) DLCI = 702, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 5605 output pkts 4176 in bytes 761663 out bytes 612942 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 2550 out DE pkts 0 out bcast pkts 2718 out bcast bytes 470716 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 14:47:44, last time pvc status changed 14:47:44 R7#s dh  sh run int t   |  b  1 / 0  R7#sh run | b 1/0  b 1/0 R7#sh run | b 1/ interface Serial1/0 no ip address encapsulation frame-relay frame-relay interface-queue priority ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown --More--   R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int s 1/0.2 R7(config-subif)#int s 1/0.2no frame-relay priority-dlci-group 1 702 702 702 702do sh fram pvc  frame-relay priority-dlci-group 1 702 702 702 702 R7(config-subif)#^Z R7#sh *Mar 1 14:49:23.128: %SYS-5-CONFIG_I: Configured from console by console R7#sh fram pvc 702 PVC Statistics for interface Serial1/0 (Frame Relay DTE) DLCI = 702, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0.2 input pkts 5614 output pkts 4186 in bytes 762659 out bytes 614570 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 2550 out DE pkts 0 out bcast pkts 2722 out bcast bytes 471864 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 14:49:05, last time pvc status changed 14:49:05 Priority DLCI Group 1, DLCI 702 (HIGH), DLCI 702 (MEDIUM) DLCI 702 (NORMAL), DLCI 702 (LOW) R7# *Mar 1 14:49:40.540: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7#sh fram pvc 702confi t sh run | b 1/0  0 R7#sh run | b 1/0   interface Serial1/0 no ip address encapsulation frame-relay frame-relay interface-queue priority ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/     s 1/9 ^ % Invalid input detected at '^' marker. R7(config)#int s 1/9 / ^ % Invalid input detected at '^' marker. R7(config)#int s 1// / ^ % Invalid input detected at '^' marker. R7(config)#int s 1//~  / 0 R7(config-if)#fram R7(config-if)#frame-relay tra R7(config-if)#frame-relay traf R7(config-if)#frame-relay traffic-shaping R7(config-if)#int s 1/0.2 R7(config-subif)#nint s 1/0.2frame-relay traffic-shaping int s 1/0 /9 frame-relay priority-dlci-group 1 702 702 702 702n frame-relay priority-dlci-group 1 702 702 702 702o frame-relay priority-dlci-group 1 702 702 702 702 frame-relay priority-dlci-group 1 702 702 702 702 R7(config-subif)# *Mar 1 14:52:04.933: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-subif)#fram class Prob6 R7(config-subif)#^Z R7# *Mar 1 14:52:12.317: %SYS-5-CONFIG_I: Configured from console by console R7# R7# R7# R7#deb prio Priority output queueing debugging is on R7#deb prioconfig tsh run | b 1/0 fram pvc 702confi t sh run | b 1/0 fram pvc 702 *Mar 1 14:52:20.811: PQ: Serial1/0 output (Pk size/Q 13/0) R7#sh fram pvc 702confi t gsh run | b 1/0u all 180.40.7.129  62 *Mar 1 14:52:27.570: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:27.570: PQ: Serial1/0 output (Pk size/Q 84/2) R7#180.40.7.162 Trying 180.40.7.162 ... Open R2# *Mar 1 14:52:29.629: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:29.629: PQ: Serial1/0 output (Pk size/Q 48/2) *Mar 1 14:52:29.701: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:29.701: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:52:29.701: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:29.705: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:29.705: PQ: Serial1/0 output (Pk size/Q 56/2) *Mar 1 14:52:29.705: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:52:29.770: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:29.770: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:52:29.770: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:29.770: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:52:29.774: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:29.774: PQ: Serial1/0 output (Pk size/Q 53/2) *Mar 1 14:52:29.778: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:29.778: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:52:29.982: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:29.982: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:52:30.811: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:52:30.875: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:30.875: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:52:30.875: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:30.875: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:30.919: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:52:30.919: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:52:31.048: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:31.048: PQ: Serial1/0 output (Pk size/Q 80/2) *Mar 1 14:52:31.376: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:31.376: PQ: Serial1/0 output (Pk size/Q 124/2) *Mar 1 14:52:31.677: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:31.677: PQ: Serial1/0 output (Pk size/Q 136/2) *Mar 1 14:52:37.086: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:37.086: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:52:37.086: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:37.130: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:52:37.586: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:37.586: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:52:40.090: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:40.090: PQ: Serial1/0 output (Pk size/Q 68/2) *Mar 1 14:52:40.291: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:40.291: PQ: Serial1/0 output (Pk size/Q 308/2) *Mar 1 14:52:40.491: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:40.491: PQ: Serial1/0 output (Pk size/Q 68/2) *Mar 1 14:52:40.587: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done *Mar 1 14:52:40.812: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:52:40.892: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:40.892: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:52:41.092: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:41.092: PQ: Serial1/0 output (Pk size/Q 148/2) *Mar 1 14:52:41.092: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:41.092: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:41.108: PQ: Serial1/0 output (Pk size/Q 148/2) *Mar 1 14:52:41.108: PQ: Serial1/0 output (Pk size/Q 136/2) *Mar 1 14:52:41.192: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:41.192: PQ: Serial1/0 output (Pk size/Q 136/2) *Mar 1 14:52:47.603: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:47.603: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:52:50.812: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:52:50.908: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:50.908: PQ: Serial1/0 output (Pk size/Q 84/2) R2# R2# R2# *Mar 1 14:52:57.619: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:52:57.619: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:52:59.190: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:59.190: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:52:59.342: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:59.342: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:52:59.502: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:59.502: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:52:59.739: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:52:59.739: PQ: Serial1/0 output (Pk size/Q 44/2)q [Connection to 180.40.7.162 closed by foreign host] R7# *Mar 1 14:53:00.812: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:53:00.925: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:53:00.925: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:53:01.021: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:53:01.021: PQ: Serial1/0 output (Pk size/Q 45/2) *Mar 1 14:53:01.109: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:53:01.109: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:53:01.249: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:53:01.249: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:53:01.273: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:53:01.273: PQ: Serial1/0 output (Pk size/Q 44/2) R7# *Mar 1 14:53:01.277: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:53:01.277: PQ: Serial1/0 output (Pk size/Q 44/2) R7# R7# R7# R7# R7# R7# R7#sh run int s *Mar 1 14:53:07.535: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:53:07.535: PQ: Serial1/0 output (Pk size/Q 84/2) R7#sh run int s 1/0 Building configuration... Current configuration : 136 bytes ! interface Serial1/0 no ip address encapsulation frame-relay frame-relay traffic-shaping frame-relay interface-queue priority end R7# *Mar 1 14:53:10.813: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:53:10.869: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:53:10.869: PQ: Serial1/0 output (Pk size/Q 84/2) R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0 R7(config-if)#no *Mar 1 14:53:17.580: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:53:17.580: PQ: Serial1/0 output (Pk size/Q 84/2) R7(config-if)#no frame-relay interface-queue priority R7(config-if)# R7(config-if)#^Z R7# R7# *Mar 1 14:53:21.170: %SYS-5-CONFIG_I: Configured from console by console R7# R7# R7# R7# R7# R7# R7#config tsh run int s 1/0180.40.7.162  Trying 180.40.7.162 ... Open R2# R2# R2# R2#q [Connection to 180.40.7.162 closed by foreign host] R7#sh deb General network interfaces: Priority output queueing debugging is on R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int s 1/0 R7(config-if)#no fram R7(config-if)#no frame-relay traff R7(config-if)#no frame-relay traffic-shaping R7(config-if)#int s 1/0.2 R7(config-subif)#no int s 1/0.2no frame-relay traffic-shaping int s 1/0 no frame-relay interface-queue priorityint s 1/0 fram class Prob6nfram class Prob6ofram class Prob6 fram class Prob6 R7(config-subif)#frame-relay priority-dlci-group 1 702 702 702 702 R7(config-subif)#^Z R7# *Mar 1 14:55:25.914: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 14:55:26.639: %SYS-5-CONFIG_I: Configured from console by console R7# R7# R7# R7# R7# R7# *Mar 1 14:55:30.834: PQ: Serial1/0: cdp -> normal *Mar 1 14:55:30.834: PQ: Serial1/0: cdp -> normal *Mar 1 14:55:30.834: PQ: Serial1/0: cdp -> normal *Mar 1 14:55:30.834: PQ: Serial1/0: cdp -> normal *Mar 1 14:55:30.834: PQ: Serial1/0: cdp -> normal *Mar 1 14:55:30.838: PQ: Serial1/0: cdp -> normal *Mar 1 14:55:30.838: PQ: Serial1/0: ip -> normal R7# *Mar 1 14:55:37.021: PQ: Serial1/0: cdp -> normal *Mar 1 14:55:37.025: PQ: Serial1/0: cdp -> normal R7# *Mar 1 14:55:39.989: PQ: Serial1/0: ip -> normal *Mar 1 14:55:40.258: PQ: Serial1/0: ip -> normal *Mar 1 14:55:40.386: PQ: Serial1/0: ip -> normal *Mar 1 14:55:40.586: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7#config tsh deb  *Mar 1 14:55:40.839: PQ: Serial1/0: ip -> normal *Mar 1 14:55:41.003: PQ: Serial1/0: ip -> normal *Mar 1 14:55:41.087: PQ: Serial1/0: ip -> normal R7#sh deb180.40.7.162 Trying 180.40.7.162 ... Open R2# R2# R2# R2# R2# *Mar 1 14:55:44.084: PQ: Serial1/0: ip -> normal *Mar 1 14:55:44.116: PQ: Serial1/0: ip -> normal *Mar 1 14:55:44.120: PQ: Serial1/0: ip -> normal *Mar 1 14:55:44.120: PQ: Serial1/0: ip -> normal *Mar 1 14:55:44.152: PQ: Serial1/0: ip -> normal *Mar 1 14:55:44.156: PQ: Serial1/0: ip -> normal *Mar 1 14:55:44.156: PQ: Serial1/0: ip -> normal *Mar 1 14:55:44.168: PQ: Serial1/0: ip -> normal *Mar 1 14:55:44.373: PQ: Serial1/0: ip -> normal *Mar 1 14:55:45.142: PQ: Serial1/0: ip -> normal *Mar 1 14:55:45.314: PQ: Serial1/0: ip -> normal *Mar 1 14:55:45.474: PQ: Serial1/0: ip -> normal *Mar 1 14:55:45.611: PQ: Serial1/0: ip -> normal *Mar 1 14:55:45.851: PQ: Serial1/0: ip -> normal R2# R2# R2# *Mar 1 14:55:50.839: PQ: Serial1/0: ip -> normal *Mar 1 14:55:51.388: PQ: Serial1/0: ip -> normal *Mar 1 14:55:51.572: PQ: Serial1/0: ip -> normal *Mar 1 14:55:51.753: PQ: Serial1/0: ip -> normal *Mar 1 14:55:51.985: PQ: Serial1/0: ip -> normal *Mar 1 14:55:52.374: PQ: Serial1/0: ip -> normal *Mar 1 14:55:52.410: PQ: Serial1/0: ip -> normal *Mar 1 14:56:00.840: PQ: Serial1/0: ip -> normal R2# R2# R2# *Mar 1 14:56:09.870: PQ: Serial1/0: ip -> normal *Mar 1 14:56:10.023: PQ: Serial1/0: ip -> normal *Mar 1 14:56:10.191: PQ: Serial1/0: ip -> normal *Mar 1 14:56:10.423: PQ: Serial1/0: ip -> normal *Mar 1 14:56:10.840: PQ: Serial1/0: ip -> normal RACK99AS> [Resuming connection 7 to r7 ... ] R2# R2# R2# *Mar 1 14:56:13.657: PQ: Serial1/0: ip -> normal *Mar 1 14:56:13.785: PQ: Serial1/0: ip -> normal *Mar 1 14:56:14.017: PQ: Serial1/0: ip -> normalq [Connection to 180.40.7.162 closed by foreign host] R7# *Mar 1 14:56:14.738: PQ: Serial1/0: ip -> normal *Mar 1 14:56:14.971: PQ: Serial1/0: ip -> normal *Mar 1 14:56:15.367: PQ: Serial1/0: ip -> normal *Mar 1 14:56:15.464: PQ: Serial1/0: ip -> normal *Mar 1 14:56:15.628: PQ: Serial1/0: ip -> normal *Mar 1 14:56:15.648: PQ: Serial1/0: ip -> normal *Mar 1 14:56:15.652: PQ: Serial1/0: ip -> normal R7# R7# R7#u all All possible debugging has been turned off R7#sh % Type "show ?" for a list of subcommands R7# R7#sh run int s 1/0 Building configuration... Current configuration : 69 bytes ! interface Serial1/0 no ip address encapsulation frame-relay end R7#sh run int s 1/0 confi gt ^ % Invalid input detected at '^' marker. R7#confi gt ^ % Invalid input detected at '^' marker. R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s1/0 R7(config-if)#fram inter R7(config-if)#fram interface-q R7(config-if)#fram interface-queue pri R7(config-if)#fram interface-queue priority R7(config-if)#^Z R7# *Mar 1 14:57:08.458: %SYS-5-CONFIG_I: Configured from console by console R7# R7# R7# R7#sh pros ^ % Invalid input detected at '^' marker. R7#sh pros  oc CPU utilization for five seconds: 0%/0%; one minute: 1%; five minutes: 3% PID QTy PC Runtime (ms) Invoked uSecs Stacks TTY Process 1 Cwe 8125C7E0 0 1 0 5796/6000 0 Chunk Manager 2 Csp 81D8C274 49 10764 4 2632/3000 0 Load Meter 3 ME 80D68B54 4585 41752 109 7132/9000 0 OSPF Hello 4 Mwe 805B2010 0 449 0 5780/6000 0 DHCPD Timer 5 Mwe 812B8C9C 0 1 023512/24000 0 EDDRI_MAIN 6 Lst 8126ACA0 59709 7297 8182 5752/6000 0 Check heaps 7 Cwe 81270C6C 4 2 2000 5696/6000 0 Pool Manager 8 Mst 8051EE9C 0 2 0 5592/6000 0 Timers 9 Mwe 80078820 4 912 4 5064/6000 0 ARP Input 10 Mwe 8011FDE4 0 2 0 5596/6000 0 ATM Idle Timer 11 Mwe 804F206C 0 2 0 5592/6000 0 AAA high-capacit 12 Mwe 805CEA08 0 3 0 5592/6000 0 DDR Timers 13 Lwe 806BAB0C 8 2 4000 5632/6000 0 Entity MIB API 14 Mwe 8080B3F0 32 2692 11 5772/6000 0 HC Counter Timer 15 Mwe 80FFE65C 0 2 0 5596/6000 0 Serial Backgroun 16 Msi 81A68978 8 1795 4 5608/6000 0 Environmental mo 17 Msp 8055A3D8 112 53817 2 5628/6000 0 GraphIt 18 Mwe 805F3048 4 2 200011596/12000 0 Dialer event 19 Mwe 81004FFC 0 1 0 5788/6000 0 SERIAL A'detect 20 Mwe 817D821C 0 2 0 5608/6000 0 SMART 21 Cwe 8127395C 0 1 0 5808/6000 0 Critical Bkgnd --More--   R7# RACK99AS>2 [Resuming connection 2 to r2 ... ] *M R2# R2# R2# R2# R2# R2# R2#asfdasdf         R2# RACK99AS>7 [Resuming connection 7 to r7 ... ] R7# R7# R7# R7#den b prio Priority output queueing debugging is on R7#deb priosh proc s *Mar 1 14:57:50.824: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:57:50.844: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:57:50.872: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:57:50.872: PQ: Serial1/0 output (Pk size/Q 84/2) R7#sh prosconfig t gtsh run int s 1/0 u all *Mar 1 14:57:57.583: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:57:57.583: PQ: Serial1/0 output (Pk size/Q 84/2) R7#u all180.40.7.162 Trying 180.40.7.162 ... Open R2# *Mar 1 14:58:00.824: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:58:00.844: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:58:00.888: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:00.888: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:02.046: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:58:02.046: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:02.046: PQ: Serial1/0 output (Pk size/Q 48/2) *Mar 1 14:58:02.078: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:58:02.078: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:02.078: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:58:02.082: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:58:02.082: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:02.082: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:58:02.082: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:02.086: PQ: Serial1/0 output (Pk size/Q 56/2) *Mar 1 14:58:02.086: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:58:02.114: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:58:02.118: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:02.118: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:58:02.118: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:58:02.118: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:02.118: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:58:02.118: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:02.122: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:58:02.122: PQ: Serial1/0 output (Pk size/Q 53/2) *Mar 1 14:58:02.130: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:58:02.130: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:02.134: PQ: Serial1/0 output (Pk size/Q 47/2) *Mar 1 14:58:02.335: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:58:02.335: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:02.335: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:58:07.623: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:58:07.623: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:10.825: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:58:10.845: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:58:10.929: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:10.929: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:17.640: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:58:17.640: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:20.825: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:58:20.845: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:58:20.945: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:20.945: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:27.556: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:58:27.556: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:30.825: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:58:30.845: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:58:30.861: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:30.861: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:37.036: PQ: Serial1/0: cdp (defaulting) -> normal *Mar 1 14:58:37.036: PQ: Serial1/0: cdp (defaulting) -> normal *Mar 1 14:58:37.112: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:58:37.112: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:58:37.112: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:37.156: PQ: Serial1/0 output (Pk size/Q 356/2) *Mar 1 14:58:37.613: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:58:37.613: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:40.826: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:58:40.846: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:58:40.918: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:40.918: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:47.629: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:58:47.629: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:50.826: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:58:50.846: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:58:50.934: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:58:50.934: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:58:57.645: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:58:57.645: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:59:00.827: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:59:00.847: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:59:00.851: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:00.851: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:59:07.562: PQ: Serial1/0 dlci 703 -> normal *Mar 1 14:59:07.562: PQ: Serial1/0 output (Pk size/Q 84/2) R2# R2# R2# R2# *Mar 1 14:59:10.827: PQ: Serial1/0 output (Pk size/Q 13/0) *Mar 1 14:59:10.847: PQ: Serial1/0: ip (defaulting) -> normal *Mar 1 14:59:10.867: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:10.867: PQ: Serial1/0 output (Pk size/Q 84/2) *Mar 1 14:59:11.144: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:59:11.148: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:11.148: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:59:11.292: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:59:11.296: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:11.296: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:59:11.440: PQ: Serial1/0: ip (tcp 23) -> highq [Connection to 180.40.7.162 closed by foreign host] R7# *Mar 1 14:59:11.440: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:11.440: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:59:11.580: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:59:11.580: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:11.580: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:59:11.809: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:59:11.809: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:11.809: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:59:12.502: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:59:12.502: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:12.502: PQ: Serial1/0 output (Pk size/Q 45/2) *Mar 1 14:59:12.646: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:59:12.646: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:12.646: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar 1 14:59:12.766: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:59:12.766: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:12.766: PQ: Serial1/0 output (Pk size/Q 46/2) *Mar R7#u 1 14:59:12.798: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:59:12.798: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:12.798: PQ: Serial1/0 output (Pk size/Q 44/2) *Mar 1 14:59:12.798: PQ: Serial1/0: ip (tcp 23) -> high *Mar 1 14:59:12.798: PQ: Serial1/0 dlci 702 -> normal *Mar 1 14:59:12.802: PQ: Serial1/0 output (Pk size/Q 44/2) R7#u all All possible debugging has been turned off R7# R7# R7# R7# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3# R3# R3# R3# R3# R3#confi gt t  t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class   R3(config)#class-map telnet R3(config-cmap)#match prot R3(config-cmap)#match protocol telnet R3(config-cmap)#exit R3(config)#class R3(config)#class-map ftp R3(config-cmap)#match pro R3(config-cmap)#match protocol ftp R3(config-cmap)#do sh ip nbar port ftp port-map ftp tcp 21 R3(config-cmap)# R3(config-cmap)# R3(config-cmap)# R3(config-cmap)#exit R3(config)#ip nbar ? pdlm PDL (protocol description language) Module port-map Map well-known port of a protocol to a new port resources Configure memory usage for tracking Stateful sessions R3(config)#ip nbar po R3(config)#ip nbar port-map ? bgp Border Gateway Protocol citrix Citrix Traffic cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 dhcp Dynamic Host Configuration dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... --More--   gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ipinip IP in IP (encapsulation) ipsec IP Security Protocol (ESP/AH) irc Internet Relay Chat kazaa2 Kazaa Version 2 kerberos Kerberos l2tp L2F/L2TP tunnel ldap Lightweight Directory Access Protocol napster Napster Traffic netbios NetBIOS netshow Microsoft Netshow nfs Network File System nntp Network News Transfer Protocol notes Lotus Notes(R) novadigm Novadigm EDM ntp Network Time Protocol pcanywhere Symantec pcANYWHERE pop3 Post Office Protocol pptp Point-to-Point Tunneling Protocol --More--   R3(config)#ip nbar port-map ftp ? tcp TCP ports R3(config)#ip nbar port-map ftp tcp ? <1-65535> Up to 16 port numbers separated by white-spaces R3(config)#ip nbar port-map ftp tcp 20 21 R3(config)#ip nbar port-map ftp tcp 20 21exit do sh ip nbar port ftp port-map ftp tcp 20 21 R3(config)#pol R3(config)#policy-map Prob7 R3(config-pmap)#class R3(config-pmap)#class tl elnet R3(config-pmap-c)#ban R3(config-pmap-c)#bandwidth re R3(config-pmap-c)#bandwidth remaining ? percent % of the remaining bandwidth R3(config-pmap-c)#bandwidth remaining p R3(config-pmap-c)#bandwidth remaining percent ? <1-100> Percentage R3(config-pmap-c)#bandwidth remaining percent 24 R3(config-pmap-c)#exit R3(config-pmap)#exitbandwidth remaining percent 24class telnet       ftp R3(config-pmap-c)#class ftpexit bandwidth remaining percent 24  51 R3(config-pmap-c)#exit R3(config-pmap)#class R3(config-pmap)#class class-dea fault R3(config-pmap-c)#class class-defaultexit bandwidth remaining percent 51  25 R3(config-pmap-c)#int s 2 1/2 R3(config-if)#max R3(config-if)#max-reserved-bandwidth 100 R3(config-if)#serv out Prob7 R3(config-if)#^Z R3#sh po *Mar 1 19:06:44.015: %SYS-5-CONFIG_I: Configured from console by console R3#sh pol int s 1/2 Serial1/2 Service-policy output: Prob7 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 41 Bandwidth remaining 24 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 42 Bandwidth remaining 51 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 --More--   Class-map: class-default (match-any) 2 packets, 108 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Output Queue: Conversation 43 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 R3#sh run | b class class-map match-all dscp26 match dscp af31 class-map match-all dscp14 match dscp af13 class-map match-all telnet match protocol telnet class-map match-all dscp12 match dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match protocol ftp ! ! policy-map test class dscp12 class dscp14 class dscp26 class dscp28 class prec3 policy-map Prob7 --More--   R3#sh run | b class     nbar ip nbar port-map ftp tcp 20 21 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! class-map match-all dscp26 match dscp af31 --More--  class-map match-all dscp14 match dscp af13 class-map match-all telnet match protocol telnet class-map match-all dscp12 match dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match protocol ftp ! ! policy-map test class dscp12 class dscp14 class dscp26 class dscp28 class prec3 policy-map Prob7 class telnet bandwidth remaining percent 24 --More--   class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address --More--   shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob7 ! interface Serial1/3 no ip address --More--   R3# RACK99AS>6 [Resuming connection 6 to r6 ... ] 03 S6#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Default DSCP Mutation Map: --More--   S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#mls qos map ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S6(config)#mls qos map ip-prec-dscp / ? <0-63> 8 dscp values separated by spaces S6(config)#mls qos map ip-prec-dscp 0 14 16 28 32 40 48 56 S6(config)#do sh ip    mls qos map ip-p IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 14 16 28 32 40 48 56 S6(config)# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol  =    l int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3096 packets, 302421 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK99AS>6 [Resuming connection 6 to r6 ... ] S6(config)#mls qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S6(config)# S6(config)# S6(config)# S6(config)# S6(config)# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#ping 180.40.7.129 10 RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#x 5 Trying 5... % Destination unreachable; gateway or host down % Unknown command or computer name, or unable to find computer address R3# R3#5sh pol int fa 0/05   RACK99AS>5 [Resuming connection 5 to r5 ... ] ^ % Invalid input detected at '^' marker. S5# S5#ping 180.40.7.129 10r10e10p10 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-tr RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#5sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3124 packets, 305325 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK99AS>6 [Resuming connection 6 to r6 ... ] S6(config)#int fa 0/7 S6(config-if)#mls qos tru S6(config-if)#mls qos trust ? cos Classify by packet COS device trusted device class dscp Classify by packet DSCP ip-precedence Classify by packet IP precedence S6(config-if)#mls qos trust ip-precedence S6(config-if)#^Z S6# RACK99AS>5 [Resuming connection 5 to r5 ... ] ping 180.40.7.129 rep 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 1/1/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3134 packets, 306305 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK99AS>6 [Resuming connection 6 to r6 ... ] 22:2 S6#sh run | mls   b mls qos mls qos map ip-prec-dscp 0 14 16 28 32 40 48 56 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 no switchport ip address 20.10.2.1 255.255.255.0 ! interface FastEthernet0/2 --More--   no switchport ip address 20.10.1.2 255.255.255.0 ! interface FastEthernet0/3 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport access vlan 10 switchport mode dynamic desirable ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 switchport access vlan 10 switchport mode dynamic desirable mls qos trust ip-precedence ! interface FastEthernet0/8 switchport mode dynamic desirable --More-- RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#mls qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S5(config)#mls qos ? aggregate-policer Assign aggregate policer cos Configure CoS setting map Define QoS mapping min-reserve Configure min-reserve buffers S5(config)#mls qos mpa  ap ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S5(config)#mls qos map dsc S5(config)#mls qos map dscp-m S5(config)#mls qos map dscp-mutation ? WORD DSCP mutation map name S5(config)#mls qos map dscp-mutation Prob9 ? <0-63> DSCP values separated by spaces (up to 8 values total) S5(config)#mls qos map dscp-mutation Prob9 14 ? <0-63> DSCP values separated by spaces (up to 8 values total) to Specify egress DSCPs S5(config)#mls qos map dscp-mutation Prob9 14 to 12 S5(config)#mls qos map dscp-mutation Prob9 14 to 12        28 to 26 S5(config)#int fa 0/24 S5(config-if)#mls qos mu S5(config-if)#mls qos mu  map ? % Unrecognized command S5(config-if)#mls qos map     ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S5(config-if)#mls qos dsc S5(config-if)#mls qos dscp-mutation ? WORD dscp-mutation name S5(config-if)#mls qos dscp-mutation Prob9  ? WORD S5(config-if)#mls qos dscp-mutation Prob9 ? S5(config-if)#mls qos dscp-mutation Prob9   S5(config-if)#mls qos tru S5(config-if)#mls qos trust dsc S5(config-if)#mls qos trust dscp S5(config-if)#^Z S5#config t 22:31:19: %SYS-5-CONFIG_I: Configured from console by console S5#config tping 180.40.7.129 rep 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 1/2/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3239 packets, 316707 bytes 5 minute offered rate 1000 bps, drop rate 0 bps Match: any R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3242 packets, 317001 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | b mls qos mls qos map dscp-mutation Prob9 14 to 12 mls qos map dscp-mutation Prob9 28 to 26 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport mode dynamic desirable ! interface FastEthernet0/2 --More--   switchport mode dynamic desirable ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport mode dynamic desirable ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 no switchport ip address 208.28.1.2 255.255.255.0 ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 --More--   switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/14 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/15 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! --More--  interface FastEthernet0/16 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/17 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/18 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/19 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/20 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/21 switchport mode dynamic desirable mls qos dscp-mutation Prob9 --More--  ! interface FastEthernet0/22 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/23 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk mls qos trust dscp mls qos dscp-mutation Prob9 ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address --More--   S5#sh run | b mls qosping 180.40.7.129 rep 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 1/2/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3275 packets, 320391 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#confi g t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#int s fa 0/24 S5(config-if)#int fa 0/24mls qos trust dscp dscp-mutation Prob9nmls qos dscp-mutation Prob9omls qos dscp-mutation Prob9 mls qos dscp-mutation Prob9 S5(config-if)#^Z S5#confi tping 180.40.7.129 rep 10 22:33:50: %SYS-5-CONFIG_I: Configured from console by console S5#ping 180.40.7.129 rep 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 1/2/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3293 packets, 322315 bytes 5 minute offered rate 1000 bps, drop rate 0 bps Match: any R3#clea ? aaa Clear AAA values access-list Clear access list statistical information access-template Access-template adjacency Adjacent nodes alps Clear Alps appletalk Reset AppleTalk information arp-cache Clear the entire ARP cache backhaul-session-manager Backhaul Session Manager information bgp Clear BGP connections bridge Reset bridge forwarding cache bsc Clear counters in command bstun Clear counters displayed in show bstun call Call cdp Reset cdp information cef CEF information related to linecard clns CLNS cns CNS agents counters Clear counters on one or all interfaces crypto Encryption subsystem decnet Reset DECnet information dialer Clear dialer statistics dlsw Data Link Switching (DLSw) --More--   R3#clea       RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#^Z S5#sh mls 22:34:20: %SYS-5-CONFIG_I: Configured from console by console S5#sh mls qos int fa0/24 FastEthernet0/24 trust state: trust dscp trust mode: trust dscp COS override: dis default COS: 0 DSCP Mutation Map: Default DSCP Mutation Map Trust device: none S5#do    sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Prob9: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 12 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 26 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-dscp mutation map: Default DSCP Mutation Map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#no mls s qos S5(config)#z ^Z S5# S5#confi tsh mls qos map 22:35:17: %SYS-5-CONFIG_I: Configured from console by console S5#sh mls qos mapint fa0/24confi t sh mls qos int fa0/24map confi t sh mls qos mapint fa0/24 FastEthernet0/24 QoS is disabled. pass-through mode When QoS is enabled, following settings will be applied trust state: trust dscp trust mode: trust dscp COS override: dis default COS: 0 DSCP Mutation Map: Default DSCP Mutation Map Trust device: none S5#sh mls qos int fa0/24confi t sh mls qos mapint fa0/24confi t ping 180.40.7.129 rep 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 1/2/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3312 packets, 324177 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#mls qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S5(config)#do sh n mls qos int fa 0/24 FastEthernet0/24 trust state: trust dscp trust mode: trust dscp COS override: dis default COS: 0 DSCP Mutation Map: Default DSCP Mutation Map Trust device: none S5(config)#^Z S5#config tping 180.40.7.129 rep 10 22:36:01: %SYS-5-CONFIG_I: Configured from console by console S5#ping 180.40.7.129 rep 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 1/2/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3329 packets, 326003 bytes 5 minute offered rate 1000 bps, drop rate 0 bps Match: any R3# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID CR2 Fas 0/8 174 R 2520 Eth 0 R3 Fas 0/3 126 R S 2611XM Fas 0/0 R7 Fas 0/7 175 R S 2611XM Fas 0/0 S6 Fas 0/24 146 R S I WS-C3550-2Fas 0/24 S6 Fas 0/22 146 R S I WS-C3550-2Fas 0/22 S5#confi gt ^ % Invalid input detected at '^' marker. S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#do sh span int fa 0/24 Vlan Role Sts Cost Prio.Nbr Type ---------------- ---- --- --------- -------- -------------------------------- VLAN0001 Altn BLK 19 128.24 P2p VLAN0010 Altn BLK 19 128.24 P2p VLAN0016 Altn BLK 19 128.24 P2p VLAN0020 Altn BLK 19 128.24 P2p VLAN0030 Altn BLK 19 128.24 P2p S5(config)#int fa 0/22 S5(config-if)#int fa 0/22           shut S5(config-if)#^Z S5# 22:37:17: %SYS-5-CONFIG_I: Configured from console by console S5# 22:37:19: %LINK-5-CHANGED: Interface FastEthernet0/22, changed state to administratively down 22:37:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down S5# S5# S5# S5# S5# S5#config t gtg t config t gtsh cdp neiping 180.40.7.129 rep 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: ......!!!! Success rate is 40 percent (4/10), round-trip min/avg/max = 1/2/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3343 packets, 327375 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# *Mar 1 22:34:53.313: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired *Mar 1 22:34:53.329: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R3# *Mar 1 22:35:00.957: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#coni fig t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int f a0/    a 0/24 S5(config-if)#int fa 0/24shut int fa 0/22do sh span int fa 0/24mls qos int fa 0/24mls qos no mls qosmls qos no mls qos dscp-mutation Prob9no mls qos dscp-mutation Prob9  mls qos dscp-mutation Prob9  S5(config-if)#^Z S5#config t 22:38:25: %SYS-5-CONFIG_I: Configured from console by console S5#config tping 180.40.7.129 rep 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 1/2/4 ms S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 3372 packets, 330761 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh mls qos map ^ % Invalid input detected at '^' marker. R3#sh mls qos map RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Prob9: --More--   S5#sh run | b mls qos mls qos map dscp-mutation Prob9 14 to 12 mls qos map dscp-mutation Prob9 28 to 26 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport mode dynamic desirable ! interface FastEthernet0/2 --More--   switchport mode dynamic desirable ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport mode dynamic desirable ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 no switchport ip address 208.28.1.2 255.255.255.0 ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 --More--   switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/14 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/15 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! --More--  interface FastEthernet0/16 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/17 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/18 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/19 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/20 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/21 switchport mode dynamic desirable mls qos dscp-mutation Prob9 --More--  ! interface FastEthernet0/22 switchport mode dynamic desirable shutdown mls qos dscp-mutation Prob9 ! interface FastEthernet0/23 switchport mode dynamic desirable mls qos dscp-mutation Prob9 ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk mls qos trust dscp mls qos dscp-mutation Prob9 ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 --More--   S5#sh mls qos int fa 0/3 qu S5#sh mls qos int fa 0/3 queueing ? | Output modifiers S5#sh mls qos int fa 0/3 queueing FastEthernet0/3 Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 Cos-queue map: cos-qid 0 - 1 1 - 1 2 - 2 3 - 2 4 - 3 5 - 3 6 - 4 7 - 4 S5# RACK99AS>6 [Resuming connection 6 to r6 ... ] 2 ! --More--   S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#int fa 0/4 S6(config-if)# S6(config-if)#mls qos ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S6(config-if)#mls qos cos ? <0-7> Class of service value between 0 and 7 override Force default COS on all packets S6(config-if)#mls qos cos 4 S6(config-if)#^Z S6# 22:47:32: %SYS-5-CONFIG_I: Configured from console by console S6# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#conm  nfig t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/24 S5(config-if)# S5(config-if)#mls qos tru S5(config-if)#mls qos trust cos ? pass-through cos pass-through mode S5(config-if)#mls qos trust cos pas S5(config-if)#mls qos trust cos pass-through dsc S5(config-if)#mls qos trust cos pass-through dscp ? S5(config-if)#mls qos trust cos pass-through dscp S5(config-if)#^Z S5#config tsh mls qos int fa 0/3 queueing 22:48:12: %SYS-5-CONFIG_I: Configured from console by console S5#sh mls qos int fa 0/3 queueing run | b mls qos mls qos map ping 180.40.7.129 rep 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!! Success rate is 100 percent (10/10), round-trip min/avg/max = 1/2/4 ms S5#^x3 % Unknown command or computer name, or unable to find computer address S5# S5# RACK99AS>3 [Resuming connection 3 to r3 ... ] ^ % Invalid input detected at '^' marker. R3#sh mls qos map sh mls qos mappol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More-- RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#mls qos map ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S5(config)#mls qos map co S5(config)#mls qos map cos-dscp ? <0-63> 8 dscp values separated by spaces S5(config)#mls qos map cos-dscp                      do sh mls qos map cos Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 S5(config)#mls qos map cos ? <0-63> 8 dscp values separated by spaces S5(config)#mls qos map cos 0 8 16 24 14 40 48 56 S5(config)#^Z S5# RACK99AS>3 [Resuming connection 3 to r3 ... ]   --More--   Class-map: prec3 (match-all) --More--   R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R4# RACK99AS>3 [Resuming connection 3 to r3 ... ] sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#pol test R4(config-pmap)#class class-dea fault R4(config-pmap-c)#set ip R4(config-pmap-c)#set ip ? dscp Set IP DSCP (DiffServ CodePointint) precedence Set IP precedence R4(config-pmap-c)#set ip dscp ? <0-63> Differentiated services codepoint value af11 Match packets with AF11 dscp (001010) af12 Match packets with AF12 dscp (001100) af13 Match packets with AF13 dscp (001110) af21 Match packets with AF21 dscp (010010) af22 Match packets with AF22 dscp (010100) af23 Match packets with AF23 dscp (010110) af31 Match packets with AF31 dscp (011010) af32 Match packets with AF32 dscp (011100) af33 Match packets with AF33 dscp (011110) af41 Match packets with AF41 dscp (100010) af42 Match packets with AF42 dscp (100100) af43 Match packets with AF43 dscp (100110) cs1 Match packets with CS1(precedence 1) dscp (001000) cs2 Match packets with CS2(precedence 2) dscp (010000) cs3 Match packets with CS3(precedence 3) dscp (011000) cs4 Match packets with CS4(precedence 4) dscp (100000) cs5 Match packets with CS5(precedence 5) dscp (101000) cs6 Match packets with CS6(precedence 6) dscp (110000) cs7 Match packets with CS7(precedence 7) dscp (111000) default Match packets with default dscp (000000) ef Match packets with EF dscp (101110) --More--   R4(config-pmap-c)#set ip dscp 2 12 R4(config-pmap-c)#^Z R4# *Mar 1 22:50:40.886: %SYS-5-CONFIG_I: Configured from console by console R4#confi tping 180.40.7.129confi t  confi tping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R4# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More-- RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#ser out test R4(config-if)#^Z R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ser out test^Z ^ % Invalid input detected at '^' marker. R4# *Mar 1 22:51:12.118: %SYS-5-CONFIG_I: Configured from console by console R4#confi t *Mar 1 22:51:14.026: %SYS-5-CONFIG_I: Configured from console by console R4#confi tping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R4# RACK99AS>3 [Resuming connection 3 to r3 ... ]   --More--   R3#[A % Unknown command or computer name, or unable to find computer address R3#[Ash pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   R3# RACK99AS>6 [Resuming connection 6 to r6 ... ] S6#confi gt  t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#int fa 0/4 S6(config-if)#mls qos tru S6(config-if)#mls qos trust dscp S6(config-if)#^Z S6# 22:52:30: %SYS-5-CONFIG_I: Configured from console by console S6# RACK99AS>5 4 [Resuming connection 4 to r4 ... ] ping 180.40.7.129confi t ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R4# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 6 packets, 668 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   R3#[A   RACK99AS>6 [Resuming connection 6 to r6 ... ] S6#sh run int fa 0/4 Building configuration... Current configuration : 130 bytes ! interface FastEthernet0/4 switchport access vlan 10 switchport mode dynamic desirable mls qos cos 4 mls qos trust dscp end S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#int fa 0/4 S6(config-if)#mls qos cos 5 S6(config-if)# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#confi gt ^ % Invalid input detected at '^' marker. R4#conifi   fig t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#pol test R4(config-pmap)#class class-default R4(config-pmap-c)#set ip dc scp ? <0-63> Differentiated services codepoint value af11 Match packets with AF11 dscp (001010) af12 Match packets with AF12 dscp (001100) af13 Match packets with AF13 dscp (001110) af21 Match packets with AF21 dscp (010010) af22 Match packets with AF22 dscp (010100) af23 Match packets with AF23 dscp (010110) af31 Match packets with AF31 dscp (011010) af32 Match packets with AF32 dscp (011100) af33 Match packets with AF33 dscp (011110) af41 Match packets with AF41 dscp (100010) af42 Match packets with AF42 dscp (100100) af43 Match packets with AF43 dscp (100110) cs1 Match packets with CS1(precedence 1) dscp (001000) cs2 Match packets with CS2(precedence 2) dscp (010000) cs3 Match packets with CS3(precedence 3) dscp (011000) cs4 Match packets with CS4(precedence 4) dscp (100000) cs5 Match packets with CS5(precedence 5) dscp (101000) cs6 Match packets with CS6(precedence 6) dscp (110000) cs7 Match packets with CS7(precedence 7) dscp (111000) default Match packets with default dscp (000000) ef Match packets with EF dscp (101110) --More--   R4(config-pmap-c)#set ip dscp ef R4(config-pmap-c)#^Z R4# RACK99AS>5 [Resuming connection 5 to r5 ... ] 22:4 S5#confi gt ^ % Invalid input detected at '^' marker. S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#mls qos map cos 0 8 16 24 14 40 48 56nmls qos map cos 0 8 16 24 14 40 48 56omls qos map cos 0 8 16 24 14 40 48 56 mls qos map cos 0 8 16 24 14 40 48 56 S5(config)# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#class   R3(config)#class-map ef R3(config-cmap)#match dscp ef R3(config-cmap)#exit R3(config)#pol test R3(config-pmap)#class ef R3(config-pmap-c)#^Z R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] *config t gtping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms R4# RACK99AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 22:52: R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 21 packets, 2138 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: ef (match-all) 8 packets, 860 bytes 5 minute offered rate 0 bps Match: dscp ef (46) Class-map: class-default (match-any) 3588 packets, 352233 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh pol int fa 0/0 confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#class ~   R3(config)#class-map Cos4 R3(config-cmap)#match ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R3(config-cmap)#match cos ? <0-7> Enter up to 4 class-of-service values separated by white-spaces R3(config-cmap)#match cos ? <0-7> Enter up to 4 class-of-service values separated by white-spaces R3(config-cmap)#match cos 4 R3(config-cmap)#exit R3(config)#exitmatch cos 4class-map Cos4 5 R3(config-cmap)#class-map Cos5exit match cos 4 5 R3(config-cmap)#pol test R3(config-pmap)#class Cos4 'match cos' supported only with IEEE 802.1Q/ISL interfaces R3(config-pmap)#exit R3(config)#no cal R3(config)#no call   lass R3(config)#no class-map Cos4 R3(config)#no class-map Cos4 5 R3(config)# R3(config)#^Z R3# *Mar 1 22:59:15.826: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# R3# R3# R3# R3# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5(config)# S5(config)# S5(config)#do sh mls qos int qu    fa 0/24    3 qu FastEthernet0/3 Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 Cos-queue map: cos-qid 0 - 1 1 - 1 2 - 2 3 - 2 4 - 3 5 - 3 6 - 4 7 - 4 S5(config)#int fa 0/3 S5(config-if)#mls ? qos Configure interface QoS parameters S5(config-if)#mls qos ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S5(config-if)#mls qos         q wr S5(config-if)#wrr-queue ? bandwidth Configure WRR bandwidth cos-map Configure cos-map for a queue id min-reserve Configure min-reserve level S5(config-if)#wrr-queue cs S5(config-if)#wrr-queue cs  co S5(config-if)#wrr-queue cos-map ? <1-4> enter cos-map queue id S5(config-if)#wrr-queue cos-map 4 ? <0-7> CoS values separated by spaces (up to 8 values total) S5(config-if)#wrr-queue cos-map 4 5 S5(config-if)#do sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Prob9: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 12 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 26 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-dscp mutation map: Default DSCP Mutation Map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 S5(config-if)#qa  wrr S5(config-if)#wrr-queue cp  S5(config-if)#wrr-queue cos-map ? <1-4> enter cos-map queue id S5(config-if)#wrr-queue cos-map 2 0 45    5   6 7 S5(config-if)#wrr-queue cos-map 2 0 4 6 7         3 3 S5(config-if)#do sh mls qos in fa 0/3 qu FastEthernet0/3 Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 Cos-queue map: cos-qid 0 - 2 1 - 1 2 - 2 3 - 3 4 - 2 5 - 4 6 - 2 7 - 2 S5(config-if)#do sh mls qos map dsc S5(config-if)#do sh mls qos map dscp-co Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 S5(config-if)#exit S5(config)#mls qos map dsc S5(config)#mls qos map dscp-c S5(config)#mls qos map dscp-cos ? <0-63> DSCP values separated by spaces (up to 8 values total) S5(config)#mls qos map dscp-cos 8 9 10 11 13 14 15 ? <0-63> DSCP values separated by spaces (up to 8 values total) to Specify COS S5(config)#mls qos map dscp-cos 8 9 10 11 13 14 15 tp   o 0 S5(config)#mls qos map dscp-cos 8 9 10 11 13 14 15 to 0                       24 25 27 28 29 30 31 to 4 S5(config)#mls qos map dscp-cos 24 25 27 28 29 30 31 to 4                         40 41 43 443 44 453 44 45 3 4 43 44 45 2 43 44 45 43 44 45 47 to 4 S5(config)#do sh mls qos map dscp-co Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 01 00 00 00 02 02 02 02 2 : 02 02 02 02 04 04 03 04 04 04 3 : 04 04 04 04 04 04 04 04 04 04 4 : 04 04 04 04 04 04 05 04 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 S5(config)#int fa 0/3 S5(config-if)#pri S5(config-if)#priority-queue o ou S5(config-if)#priority-queue out     ? out egress priority queue S5(config-if)#priority-queue ou S5(config-if)#priority-queue out S5(config-if)#do sh mls qos int fa 0/3 qwu   FastEthernet0/3 Egress expedite queue: ena wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 when expedite queue is disabled Cos-queue map: cos-qid 0 - 2 1 - 1 2 - 2 3 - 3 4 - 2 5 - 4 6 - 2 7 - 2 S5(config-if)#wrr S5(config-if)#wrr-queue ? bandwidth Configure WRR bandwidth cos-map Configure cos-map for a queue id min-reserve Configure min-reserve level S5(config-if)#wrr-queue ba S5(config-if)#wrr-queue bandwidth ? <1-65536> enter bandwidth weight for qid 1 S5(config-if)#wrr-queue bandwidth 30 40 30 1 S5(config-if)#^Z S5#sh run 23:14:52: %SYS-5-CONFIG_I: Configured from console by console S5#sh run     mls qos int af 0/3 q ^ % Invalid input detected at '^' marker. S5#sh mls qos int af 0/3 qf 0/3 q  FastEthernet0/3 Egress expedite queue: ena wrr bandwidth weights: qid-weights 1 - 30 2 - 40 3 - 30 4 - 1 when expedite queue is disabled Cos-queue map: cos-qid 0 - 2 1 - 1 2 - 2 3 - 3 4 - 2 5 - 4 6 - 2 7 - 2 S5# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R4# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#confi tsh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 21 packets, 2138 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: ef (match-all) 139 packets, 13814 bytes 5 minute offered rate 0 bps Match: dscp ef (46) Class-map: class-default (match-any) 3713 packets, 364447 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] ping 180.40.7.129 ping 180.40.7.129 rep 10000 Type escape sequence to abort. Sending 10000, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!! RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 21 packets, 2138 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: ef (match-all) 705 packets, 78322 bytes 5 minute offered rate 2000 bps Match: dscp ef (46) Class-map: class-default (match-any) 3715 packets, 364643 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 21 packets, 2138 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: ef (match-all) 1540 packets, 173496 bytes 5 minute offered rate 2000 bps Match: dscp ef (46) Class-map: class-default (match-any) 3715 packets, 364643 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# sh pol int fa 0/0 FastEthernet0/0 Service-policy input: test Class-map: dscp12 (match-all) 21 packets, 2138 bytes 5 minute offered rate 0 bps Match: dscp af12 (12) Class-map: dscp14 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: dscp af13 (14) Class-map: dscp26 (match-all) 20 packets, 2280 bytes 5 minute offered rate 0 bps Match: dscp af31 (26) Class-map: dscp28 (match-all) 24 packets, 2736 bytes 5 minute offered rate 0 bps Match: dscp af32 (28) --More--   Class-map: prec3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: ef (match-all) 2244 packets, 253752 bytes 5 minute offered rate 2000 bps Match: dscp ef (46) Class-map: class-default (match-any) 3715 packets, 364643 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#    RACK99AS>4 [Resuming connection 4 to r4 ... ] !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!! R4#sh reun     un | b class class class-default set ip dscp ef ! ! ! ! ! interface Loopback0 ip address 100.1.1.1 255.255.255.0 ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 duplex auto speed auto service-policy output test ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! router ospf 1 log-adjacency-changes --More--   R4#sh run | b class     pol policy-map test class class-default set ip dscp ef ! ! ! ! ! interface Loopback0 ip address 100.1.1.1 255.255.255.0 ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 duplex auto speed auto service-policy output test ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! router ospf 1 --More--   R4# RACK99AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | b mls mls qos map dscp-mutation Prob9 14 to 12 mls qos map dscp-mutation Prob9 28 to 26 mls qos map dscp-cos 8 9 10 11 13 14 15 to 0 mls qos map dscp-cos 24 25 27 28 29 30 31 40 to 4 mls qos map dscp-cos 41 42 43 44 45 47 to 4 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 --More--   switchport mode dynamic desirable ! interface FastEthernet0/2 switchport mode dynamic desirable ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable wrr-queue bandwidth 30 40 30 1 wrr-queue cos-map 1 1 wrr-queue cos-map 2 0 2 4 6 7 wrr-queue cos-map 3 3 wrr-queue cos-map 4 5 priority-queue out ! interface FastEthernet0/4 switchport mode dynamic desirable ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable --More--   S5# RACK99AS>6 [Resuming connection 6 to r6 ... ] S6(config-if)#^Z S6#sh run in 23:19:08: %SYS-5-CONFIG_I: Configured from console by console S6#sh run int fa 0/4 Building configuration... Current configuration : 130 bytes ! interface FastEthernet0/4 switchport access vlan 10 switchport mode dynamic desirable mls qos cos 5 mls qos trust dscp end S6# S6# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#do sh class Class Map match-all dscp26 (id 3) Match dscp af31 (26) Class Map match-all dscp14 (id 2) Match dscp af13 (14) Class Map match-all telnet (id 6) Match protocol telnet Class Map match-all ef (id 8) Match dscp ef (46) Class Map match-all dscp12 (id 1) Match dscp af12 (12) Class Map match-all dscp28 (id 4) Match dscp af32 (28) Class Map match-any class-default (id 0) Match any Class Map match-all prec3 (id 5) Match ip precedence 3 --More--   R3(config)#pol R3(config)#policy-map Prob11 R3(config-pmap)#class dscp12 R3(config-pmap-c)#pri R3(config-pmap-c)#priority per R3(config-pmap-c)#priority percent 25 R3(config-pmap-c)#do sh run int s 1/2 Building configuration... Current configuration : 123 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob7 end R3(config-pmap-c)#do sh run | b pol policy-map test class dscp12 class dscp14 class dscp26 class dscp28 class prec3 class ef policy-map Prob7 class telnet bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 policy-map Prob11 class dscp12 priority percent 25 ! ! ! ! ! ! --More--   R3(config-pmap-c)#exit R3(config-pmap)# no policy-map Prob11 R3(config)#policy-map Prob7 R3(config-pmap)# class dscp12 R3(config-pmap-c)# priority percent 25 R3(config-pmap-c)#do sh pol Policy Map test Class dscp12 Class dscp14 Class dscp26 Class dscp28 Class prec3 Class ef Policy Map Prob7 Class telnet Bandwidth remaining 24 (%) Max Threshold 64 (packets) Class ftp Bandwidth remaining 51 (%) Max Threshold 64 (packets) Class dscp12 Strict Priority Bandwidth 25 (%) Class class-default Bandwidth remaining 25 (%) Max Threshold 64 (packets) R3(config-pmap-c)#do sh rnu  un | b pol policy-map test class dscp12 class dscp14 class dscp26 class dscp28 class prec3 class ef policy-map Prob7 class telnet bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class dscp12 priority percent 25 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 --More--   R3(config-pmap-c)#int s 1/2 R3(config-if)#no serv out Prob7 R3(config-if)#no policy-map Prob7 R3(config)#policy-map Prob711 R3(config-pmap)# class class-default R3(config-pmap-c)# bandwidth remaining percent 25 R3(config-pmap-c)# class telnet R3(config-pmap-c)# bandwidth remaining percent 24 R3(config-pmap-c)# class ftp R3(config-pmap-c)# bandwidth remaining percent 51 R3(config-pmap-c)# class dscp12 R3(config-pmap-c)# priority percent 25 R3(config-pmap-c)# R3(config-pmap-c)#int s 1/2 R3(config-if)#serv out Prob711 R3(config-if)#^Z R3# *Mar 1 23:22:25.164: %SYS-5-CONFIG_I: Configured from console by console R3#sh pol int s 1/2 Serial1/2 Service-policy output: Prob711 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 41 Bandwidth remaining 24 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 42 Bandwidth remaining 51 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 --More--   Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 (12) Queueing Strict Priority Output Queue: Conversation 40 Bandwidth 25 (%) Bandwidth 32 (kbps) Burst 800 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: class-default (match-any) 2 packets, 108 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Output Queue: Conversation 43 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 R3#sh    confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int s 1/2 R3(config-if)#no serv out Prob711 R3(config-if)#no policy-map Prob711 R3(config)#policy-map Prob711 R3(config-pmap)# class dscp12 R3(config-pmap-c)# priority percent 25 R3(config-pmap-c)# class telnet R3(config-pmap-c)# bandwidth remaining percent 24 R3(config-pmap-c)# class ftp R3(config-pmap-c)# bandwidth remaining percent 51 R3(config-pmap-c)# R3(config-pmap-c)# class class-default R3(config-pmap-c)# bandwidth remaining percent 25 R3(config-pmap-c)#int s 1/2 R3(config-if)#serv out Prob711 R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#^Z R3#sh *Mar 1 23:23:26.601: %SYS-5-CONFIG_I: Configured from console by console R3#sh pol int s 1/2 Serial1/2 Service-policy output: Prob711 Class-map: dscp12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: dscp af12 (12) Queueing Strict Priority Output Queue: Conversation 40 Bandwidth 25 (%) Bandwidth 32 (kbps) Burst 800 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 41 Bandwidth remaining 24 (%) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 42 Bandwidth remaining 51 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 1 packets, 84 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Output Queue: Conversation 43 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 R3#sh run | b class class-map match-all dscp26 match dscp af31 class-map match-all dscp14 match dscp af13 class-map match-all telnet match protocol telnet class-map match-all ef match dscp ef class-map match-all dscp12 match dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match protocol ftp ! ! policy-map test class dscp12 class dscp14 class dscp26 class dscp28 --More--   class prec3 class ef policy-map Prob711 class dscp12 priority percent 25 class telnet bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto service-policy input test --More--  ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network broadcast frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address shutdown ! --More--  interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob711 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address --More--   R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# RACK99AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int fa 0/1 R7(config-if)#st  ST R7(config-if)#STandby ? <0-255> group number authentication Authentication delay HSRP initialisation delay ip Enable HSRP and set the virtual IP address mac-address Virtual MAC address name Redundancy name string preempt Overthrow lower priority Active routers priority Priority level redirects Configure sending of ICMP Redirect messages with an HSRP virtual IP address as the gateway IP address timers Hello and hold timers track Priority tracking use-bia HSRP uses interface's burned in address R7(config-if)#STandby 47 ip 180.40.7.132 R7(config-if)#do sh *Mar 1 19:27:42.154: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 47 state Standby -> Active R7(config-if)#do sh st % Ambiguous command: "sh st" R7(config-if)#do sh stand FastEthernet0/1 - Group 47 State is Active 2 state changes, last state change 00:00:05 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.287 secs Preemption disabled Active router is local Standby router is unknown Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/1-47" (default) R7(config-if)#^x3 ^ % Invalid input detected at '^' marker. R7(config-if)# R7(config-if)# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3(config)#int fa 0/0 R3(config-if)#STandby 47 ip 180.40.7.132 R3(config-if)#st R3(config-if)#standby 100   pri R3(config-if)#standby priority 100  50 R3(config-if)#do sh stand FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:00:28 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 1.898 secs Preemption disabled Active router is 180.40.7.131, priority 100 (expires in 7.432 sec) Standby router is local Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/0-47" (default) R3(config-if)#do sh standstandby priority 150no    nstandby priority 150ostandby priority 150 standby priority 150 R3(config-if)#no standby priority 150do sh stand standby priority 1504priority 1507priority 150 priority 150 R3(config-if)#standby 47 priority 150no standby priority 150do sh stand  brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 Standby 180.40.7.131 local 180.40.7.132 R3(config-if)#st R3(config-if)#standby 47 pre R3(config-if)#standby 47 preempt R3(config-if)#standby 47 preempt *Mar 1 23:32:24.414: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active R3(config-if)#standby 47 preempt ? delay Wait before preempting R3(config-if)#standby 47 preempt del ? minimum Delay at least this long reload Delay after reload sync Wait for IP redundancy clients R3(config-if)#standby 47 preempt del mi R3(config-if)#standby 47 preempt del minimum ? <0-3600> Number of seconds for minimum delay R3(config-if)#standby 47 preempt del minimum                                st R3(config-if)#standby 47 tr R3(config-if)#standby 47 track ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing R3(config-if)#standby 47 track ser 1/0 ? <1-255> Decrement value R3(config-if)#standby 47 track ser 1/0 51 R3(config-if)#standby 47 track ser 1/0 51 51 2 51 R3(config-if)#^Z R3# RACK99AS>7 [Resuming connection 7 to r7 ... ] *M R7(config-if)#stan R7(config-if)#standby 47 pre R7(config-if)#standby 47 preempt R7(config-if)#^Z R7# *Mar 1 19:35:11.454: %SYS-5-CONFIG_I: Configured from console by console R7# RACK99AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#int s /2  1/2 R2(config-if)#shut R2(config-if)# *Mar 1 23:36:51.893: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-if)# RACK99AS>3 [Resuming connection 3 to r3 ... ] *Ma9: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Active -> Speak *Mar 1 23:36:49.104: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down R3# R3# *Mar 1 23:36:49.104: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 23:36:50.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 99 P Standby 180.40.7.131 local 180.40.7.132 R3# R3# R3# R3# R3# RACK99AS>2 [Resuming connection 2 to r2 ... ] *Ma R2(config-if)#no shut R2(config-if)#^Z R2# *Mar 1 23:38:19.524: %SYS-5-CONFIG_I: Configured from console by console R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh *Mar 1 23:38:18.527: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active R3#sh run int s 1/2     da  fa 0/0 *Mar 1 23:38:26.536: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from LOADING to FULL, Loading Done R3#sh run int fa 0/0 Building configuration... Current configuration : 288 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 service-policy input test end R3#qsh run int fa 0/0 Building configuration... Current configuration : 288 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 service-policy input test end R3# RACK99AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#shj    run int s   fa 0/1 Building configuration... Current configuration : 176 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 end R7# R7# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:01:42, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.67, 00:01:42, Serial1/0 [110/792] via 180.40.7.2, 00:01:42, Serial1/2 O 20.10.1.0 [110/782] via 180.40.7.67, 00:01:42, Serial1/0 [110/782] via 180.40.7.2, 00:01:42, Serial1/2 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:01:42, FastEthernet0/0 180.40.0.0/27 is subnetted, 4 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 O 180.40.7.160 [110/782] via 180.40.7.131, 00:01:43, FastEthernet0/0 C 180.40.7.0 is directly connected, Serial1/2 C 180.40.7.64 is directly connected, Serial1/0 R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#tr R3(config)#tra R3(config)#trac R3(config)#track ? <1-500> Tracked object resolution Tracking resolution parameters timer Polling interval timers R3(config)#track 1 ? interface Select an interface to track ip IP protocol R3(config)#track 1 ip ? route IP route R3(config)#track 1 ip rou ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R3(config)#track 1 ip rou 20.10.2.0/24 ? metric Route metric reachability Route reachability state R3(config)#track 1 ip rou 20.10.2.0/24 re R3(config)#track 1 ip rou 20.10.2.0/24 reachability ? R3(config)#track 1 ip rou 20.10.2.0/24 reachability % Cannot change object created via HSRP R3(config)#track 1 ip rou 20.10.2.0/24 reachability  ip rou 20.10.2.0/24 reachability 2 ip rou 20.10.2.0/24 reachability  % Cannot change object created via HSRP R3(config)#track 2 ip rou 20.10.2.0/24 reachability  ip rou 20.10.2.0/24 reachability 3 ip rou 20.10.2.0/24 reachability  R3(config-track)#int fa 0/0 R3(config-if)#st R3(config-if)#standby 47 TR R3(config-if)#standby 47 TRack ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing R3(config-if)#standby 47 TRack 3 ? decrement Priority decrement R3(config-if)#standby 47 TRack 3 de R3(config-if)#standby 47 TRack 3 decrement ? <1-255> Decrement value R3(config-if)#standby 47 TRack 3 decrement 60 ? R3(config-if)#standby 47 TRack 3 decrement 60 R3(config-if)#^Z R3# *Mar 1 23:42:14.181: %SYS-5-CONFIG_I: Configured from console by console R3# RACK99AS>6 [Resuming connection 6 to r6 ... ] S6#coni fig t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/1 S6(config-if)#shut S6(config-if)# 23:45:29: %OSPF-5-ADJCHG: RACK99AS>3 [Resuming connection 3 to r3 ... ] R3# R3# R3# R3#sh ip rout Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:00:03, FastEthernet0/0 20.0.0.0/24 is subnetted, 1 subnets O 20.10.1.0 [110/782] via 180.40.7.67, 00:00:03, Serial1/0 [110/782] via 180.40.7.2, 00:00:03, Serial1/2 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:03, FastEthernet0/0 180.40.0.0/27 is subnetted, 4 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 O 180.40.7.160 [110/782] via 180.40.7.131, 00:00:05, FastEthernet0/0 C 180.40.7.0 is directly connected, Serial1/2 C 180.40.7.64 is directly connected, Serial1/0 R3#q sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 P Active local 180.40.7.131 180.40.7.132 R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 90 P Active local 180.40.7.131 180.40.7.132 R3# R3# R3# R3# R3# *Mar 1 23:42:45.725: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Active -> Speak R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 90 P Speak 180.40.7.131 unknown 180.40.7.132 R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 90 P Speak 180.40.7.131 unknown 180.40.7.132 R3#sh stand brie P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 90 P Standby 180.40.7.131 local 180.40.7.132 R3# R3# R3# R3# R3# RACK99AS>6 [Resuming connection 6 to r6 ... ] Process 1, Nbr 20.10.2.2 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached S6(config-if)# S6(config-if)#no shut S6(config-if)#^Z S6# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | trackl  ^ % Invalid input detected at '^' marker. R3#sh run | trackbtrack track track 3 ip route 20.10.2.0 255.255.255.0 reachability ! ! ! class-map match-all dscp26 match dscp af31 class-map match-all dscp14 match dscp af13 class-map match-all telnet match protocol telnet class-map match-all ef match dscp ef class-map match-all dscp12 match dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match protocol ftp ! ! policy-map test --More--   class dscp12 class dscp14 class dscp26 class dscp28 class prec3 class ef policy-map Prob711 class dscp12 priority percent 25 class telnet bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 --More-- *Mar 1 23:44:15.756: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active --More--   ip policy route-map Prob1 duplex auto speed auto standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 standby 47 track 3 decrement 60 service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 --More--   R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int fa 0/0 R3(config-if)#vrrp ? <1-255> Group number R3(config-if)#vrrp 47 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R3(config-if)#vrrp 47 ip 180.40.7.133 R3(config-if)# *Mar 1 23:49:35.064: %VRRP-6-STATECHANGE: Fa0/0 Grp 47 state Init -> Backup R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# *Mar 1 23:49:38.674: %VRRP-6-STATECHANGE: Fa0/0 Grp 47 state Backup -> Master R3(config-if)#vrrp 47 ip 180.40.7.133               pre i R3(config-if)#vrrp 47 priority 150 R3(config-if)#^Z R3#sh *Mar 1 23:50:11.864: %SYS-5-CONFIG_I: Configured from console by console R3#sh vrrp FastEthernet0/0 - Group 47 State is Master Virtual IP address is 180.40.7.133 Virtual MAC address is 0000.5e00.012f Advertisement interval is 1.000 sec Preemption enabled Priority is 150 Master Router is 180.40.7.129 (local), priority is 150 Master Advertisement interval is 1.000 sec Master Down interval is 3.414 sec R3# RACK99AS>7 [Resuming connection 7 to r7 ... ] * R7#conif  fig t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#vrrp 47 ip 190  80.40.7  .133 R7(config-if)# *Mar 1 19:51:05.927: %VRRP-6-STATECHANGE: Fa0/1 Grp 47 state Init -> Backup R7(config-if)#^Z R7# *Mar 1 19:51:07.866: %SYS-5-CONFIG_I: Configured from console by console R7#^x3 % Unknown command or computer name, or unable to find computer address R7# R7# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#iint     nt fa 0/0 R3(config-if)#vrrp 47 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R3(config-if)#vrrp 47         ^Z R3# *Mar 1 23:52:46.225: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# R3# R3#sh run int fa 0/0 Building configuration... Current configuration : 368 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 47 ip 180.40.7.133 vrrp 47 priority 150 standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 standby 47 track 3 decrement 60 service-policy input test end R3#^x4 % Unknown command or computer name, or unable to find computer address R3# R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#no ip pol R4(config)#no ip policy-list           R4(config)#no ip policy-list               p loc R4(config)#no ip local pol R4(config)#no ip local policy rou R4(config)#no ip local policy route-map Prob2 R4(config)#^Z R4# *Mar 1 23:55:56.474: %SYS-5-CONFIG_I: Configured from console by console R4#ping 180.40.7.133 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.133, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/3/4 ms R4#ping 180.40.7.133 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.132, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 4/4/4 ms R4#sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 236 0012.7f80.f441 ARPA FastEthernet0/0 Internet 180.40.7.130 - 0001.96de.2580 ARPA FastEthernet0/0 Internet 180.40.7.129 237 0012.7f8d.1ea0 ARPA FastEthernet0/0 Internet 180.40.7.133 0 0000.5e00.012f ARPA FastEthernet0/0 Internet 180.40.7.132 0 0000.0c07.ac2f ARPA FastEthernet0/0 R4# RACK99AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int s f 0/1 Building configuration... Current configuration : 201 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 47 ip 180.40.7.133 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 end R7# R7# R7# R7# R7# R7# R7# RACK99AS>6 [Resuming connection 6 to r6 ... ] 23 S6#sh cap S6#sh cap? % Unrecognized command S6#sh cap   int ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface EsconPhy ESCON interface FastEthernet FastEthernet IEEE 802.3 Filter Filter interface Filtergroup Filter Group interface GigabitEthernet GigabitEthernet IEEE 802.3z LongReachEthernet Long-Reach Ethernet interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Portgroup Portgroup interface Pos-channel POS Channel of interfaces SYSCLOCK Telecom-Bus Clock Controller Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing --More--   S6#sh int gi 0/1 ? accounting Show interface accounting capabilities Show interface capabilities information controller Show interface status, configuration and controller status counters Show interface counters crb Show interface routing/bridging info dampening Show interface dampening info debounce Show interface debounce time info description Show interface description etherchannel Show interface etherchannel information fair-queue Show interface Weighted Fair Queueing (WFQ) info flowcontrol Show interface flowcontrol information irb Show interface routing/bridging info mac-accounting Show interface MAC accounting info mpls-exp Show interface MPLS experimental accounting info mtu Show interface mtu precedence Show interface precedence accounting info private-vlan Show interface private vlan information pruning Show interface trunk VTP pruning information random-detect Show interface Weighted Random Early Detection (WRED) info rate-limit Show interface rate-limit info stats Show interface packets & octets, in & out, by switching path status Show interface line status --More--   S6#sh int gi 0/1 ac  cap S6#sh int gi 0/1 capabilities ? | Output modifiers S6#sh int gi 0/1 capabilities GigabitEthernet0/1 Model: WS-C3550-24 Type: unknown Speed: 1000 Duplex: full Trunk encap. type: 802.1Q,ISL Trunk mode: on,off,desirable,nonegotiate Channel: yes Broadcast suppression: percentage(0-100) Flowcontrol: rx-(off,on,desired),tx-(off,on,desired) Fast Start: yes QOS scheduling: rx-(1q0t),tx-(4q2t),tx-(1p3q2t) CoS rewrite: yes ToS rewrite: yes UDLD: yes Inline power: no SPAN: source/destination PortSecure: yes Dot1x: yes S6#sh int gi 0/1 capabilities  0/1 capabilities  0/1 capabilities f 0/1 capabilities a 0/1 capabilities  FastEthernet0/1 Model: WS-C3550-24 Type: 10/100BaseTX Speed: 10,100,auto Duplex: half,full,auto Trunk encap. type: 802.1Q,ISL Trunk mode: on,off,desirable,nonegotiate Channel: yes Broadcast suppression: percentage(0-100) Flowcontrol: rx-(off,on,desired),tx-(none) Fast Start: yes QOS scheduling: rx-(1q0t),tx-(4q0t),tx-(1p3q0t) CoS rewrite: yes ToS rewrite: yes UDLD: yes Inline power: no SPAN: source/destination PortSecure: yes Dot1x: yes S6# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#ip dhc R3(config)#ip dhcp ex R3(config)#ip dhcp excluded-address 180.40.7.131 180.40.7.134 R3(config)#ip dchp pool Prob` 15 ^ % Invalid input detected at '^' marker. R3(config)#ip dchp pool Prob15p pool Prob15 p pool Prob15 hp pool Prob15cp pool Prob15 R3(dhcp-config)#net R3(dhcp-config)#netw R3(dhcp-config)#network 180.40.7.128 /27 R3(dhcp-config)#ip de R3(dhcp-config)#ip def R3(dhcp-config)#ip def      def R3(dhcp-config)#default-router ? Hostname or A.B.C.D Router's name or IP address R3(dhcp-config)#default-router 180.40.7.132 R3(dhcp-config)#dom R3(dhcp-config)#domain-name ? WORD Domain name R3(dhcp-config)#domain-name cciestudn  dent.com R3(dhcp-config)#dn R3(dhcp-config)#dns-server 20 8 08.28.1.82 R3(dhcp-config)#op R3(dhcp-config)#option ? <0-254> DHCP option code R3(dhcp-config)#option 255   150 ? ascii Data is an NVT ASCII string hex Data is a hexadecimal string instance Specify the option instance ip Data is one or more IP addresses R3(dhcp-config)#option 150 ip ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#option 150 ip 20.20.20.20 R3(dhcp-config)#^Z R3# *Mar 2 02:06:15.535: %SYS-5-CONFIG_I: Configured from console by console R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#do deb ip dhc  hcp ev deb ip dhcp ev ^ % Invalid input detected at '^' marker. R4(config-if)#do deb ip dhcp ev    de deb ip dhcp de ^ % Invalid input detected at '^' marker. R4(config-if)#^Z R4#de *Mar 2 02:09:47.641: %SYS-5-CONFIG_I: Configured from console by console R4#deb ip dhcp ? server DHCP server activity R4#deb ip dhcp ser ? events Report address assignments, lease expirations, etc. linkage Show database linkage packet Decode message receptions and transmissions R4#deb ip dhcp ser ev                dhcp ? detail DHCP packet content R4#deb dhcp de ? R4#deb dhcp de DHCP client activity debugging is on (detailed) R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#ip add        do sh run int fa 0/0-  Building configuration... Current configuration : 127 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 duplex auto speed auto service-policy output test end R4(config-if)#ip add dhcp R4(config-if)# *Mar 2 02:10:36.125: DHCP: DHCP client process started: 10 *Mar 2 02:10:36.125: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 02:10:36.125: DHCP: Try 1 to acquire address for FastEthernet0/0 R4(config-if)# *Mar 2 02:10:36.129: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from 2WAY to DOWN, Neighbor Down: Interface down or detached *Mar 2 02:10:36.133: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)# *Mar 2 02:10:39.377: DHCP: Shutting down from get_netinfo() *Mar 2 02:10:39.377: DHCP: Attempting to shutdown DHCP Client *Mar 2 02:10:41.157: DHCP: allocate request *Mar 2 02:10:41.157: DHCP: new entry. add to queue *Mar 2 02:10:41.157: DHCP: SDiscover attempt # 1 for entry: *Mar 2 02:10:41.157: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 02:10:41.157: Temp sub net mask: 0.0.0.0 *Mar 2 02:10:41.157: DHCP Lease server: 0.0.0.0, state: 1 Selecting *Mar 2 02:10:41.157: DHCP transaction id: 59E10E1 *Mar 2 02:10:41.157: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 02:10:41.157: Next timer fires after: 00:00:03 *Mar 2 02:10:41.157: Retry count: 1 Client-ID: cisco-0001.96de.2580-Fa0/0 *Mar 2 02:10:41.161: Hostname: R4 R4(config-if)# *Mar 2 02:10:41.161: DHCP: SDiscover: sending 294 byte length DHCP packet *Mar 2 02:10:41.161: DHCP: SDiscover 294 bytes *Mar 2 02:10:41.161: B'cast on FastEthernet0/0 interface from 0.0.0.0 R4(config-if)# *Mar 2 02:10:43.169: DHCP: Received a BOOTREP pkt *Mar 2 02:10:43.169: DHCP: Scan: Message type: DHCP Offer *Mar 2 02:10:43.169: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 02:10:43.169: DHCP: Scan: Lease Time: 86400 *Mar 2 02:10:43.169: DHCP: Scan: Renewal time: 43200 *Mar 2 02:10:43.169: DHCP: Scan: Rebind time: 75600 *Mar 2 02:10:43.169: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 02:10:43.169: DHCP: Scan: Router Option: 180.40.7.132 *Mar 2 02:10:43.173: DHCP: Scan: Domain Name: cciestudent.com *Mar 2 02:10:43.173: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 02:10:43.173: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 02:10:43.173: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 02:10:43.173: UDP sport: 43, dport: 44, length: 317 *Mar 2 02:10:43.173: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 02:10:43.173: DHCP server identifier: 180.40.7.129 *Mar 2 02:10 R4(config-if)#:43.173: xid: 59E10E1, secs: 0, flags: 8000 *Mar 2 02:10:43.173: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 02:10:43.173: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 02:10:43.173: options block length: 69 *Mar 2 02:10:43.177: DHCP Offer Message Offered Address: 180.40.7.130 *Mar 2 02:10:43.177: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 02:10:43.177: DHCP: Server ID Option: 180.40.7.129 *Mar 2 02:10:43.177: DHCP: offer received from 180.40.7.129 *Mar 2 02:10:43.177: DHCP: SRequest attempt # 1 for entry: *Mar 2 02:10:43.177: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 02:10:43.177: Temp sub net mask: 255.255.255.224 *Mar 2 02:10:43.177: DHCP Lease server: 180.40.7.129, state: 2 Requesting *Mar 2 02:10:43.177: DHCP transaction id: 59E10E1 *Mar 2 02:10:43.177: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 02:10:43.181: Next timer fires after: 00:00:01 *Mar 2 02:10:43.181: Retry count: 1 Client-ID: cisco-0001.96de.2580-Fa0/0 *Mar 2 02:10:43.181: Hostname: R4 *Mar 2 02:10:43.181: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 02:10:43.181: DHCP: SRequest- Requested IP addr option: 180.40.7.130 *Mar 2 02:10:43.181: DHCP: SRequest placed lease len option: 86400 *Mar 2 02:10:43.181: DHCP: SRequest: 312 bytes *Mar 2 02:10:43.181: DHCP: SRequest: 312 bytes *Mar 2 02:10:43.185: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 02:10:43.189: DHCP: Received a BOOTREP pkt *Mar 2 02:10:43.189: DHCP: Scan: Message type: DHCP Ack *Mar 2 02:10:43.189: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 02:10:43.189: DHCP: Scan: Lease Time: 86400 *Mar 2 02:10:43.189: DHCP: Scan: Renewal time: 43200 *Mar 2 02:10:43.193: DHCP: Scan: Rebind time: 75600 *Mar 2 02:10:43.193: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 02:10:43.193: DHCP: Scan: Router Option: 180.40.7.132 *Mar 2 02:10:43.193: DHCP: Scan: Domain Name: cciestudent.com *Mar 2 02:10:43.193: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 02:10:43.193: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 02:10:43.193: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 02:10:43.193: UDP sport: 43, dport: 44, length: 317 *Mar 2 02:10:43.193: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 02:10:43.193: DHCP server identifier: 180.40.7.129 *Mar 2 02:10:43.193: xid: 59E10E1, secs: 0, flags: 8000 *Mar 2 02:10:43.193: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 02:10:43.197: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 02:10:43.197: options block length: 69 *Mar 2 02:10:43.197: DHCP Ack Message *Mar 2 02:10:43.197: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 02:10:43.197: DHCP: Server ID Option: 180.40.7.129 *Mar 2 02:10:46.205: DHCP: Releasing ipl options: *Mar 2 02:10:46.209: DHCP: Applying DHCP options: *Mar 2 02:10:46.209: Setting default_gateway to 180.40.7.132 *Mar 2 02:10:46.209: Adding default route 180.40.7.132 R4(config-if)# R4(config-if)# *Mar 2 02:10:47.209: Adding DNS server address 208.28.1.82 *Mar 2 02:10:47.209: Setting default domain to cciestudent.com *Mar 2 02:10:47.209: DHCP Client Pooling: ***Allocated IP address: 180.40.7.130 *Mar 2 02:10:47.305: Allocated IP address = 180.40.7.130 255.255.255.224 R4(config-if)# *Mar 2 02:10:47.305: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.224, hostname R4 R4(config-if)# *Mar 2 02:10:55.277: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 02:10:55.277: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)# RACK99AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh ip dhcp bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 0063.6973.636f.2d30. Mar 03 1993 02:08 AM Automatic 3030.312e.3936.6465. 2e32.3538.302d.4661. 302f.30 R3#clea ip dhcp bin * R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] R4(config-if)#ip add dhcp ? client-id Specify client-id to use hostname Specify value for hostname option R4(config-if)#ip add dhcp cli ? FastEthernet FastEthernet IEEE 802.3 R4(config-if)#ip add dhcp cli fa ? <0-6> FastEthernet interface number R4(config-if)#ip add dhcp cli fa 0. /0 ? hostname Specify value for hostname option R4(config-if)#ip add dhcp cli fa 0/0 *Mar 2 02:12:07.261: DHCP: SRelease attempt # 1 for entry: *Mar 2 02:12:07.261: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 02:12:07.261: Temp sub net mask: 255.255.255.224 *Mar 2 02:12:07.261: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 02:12:07.261: DHCP transaction id: 59E10E1 *Mar 2 02:12:07.261: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 02:12:07.261: Temp default-gateway addr: 180.40.7.132 *Mar 2 02:12:07.265: Next timer fires after: 00:00:01 *Mar 2 02:12:07.265: Retry count: 1 Client-ID: cisco-0001.96de.2580-Fa0/0 *Mar 2 02:12:07.265: Hostname: R4 *Mar 2 02:12:07.265: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 02:12:07.265: DHCP: SRelease: 279 bytes *Mar 2 02:12:07.329: DHCP: SRelease attempt # 2 for entry: *Mar 2 02:12:07.329: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 02:12:07.329: Temp sub net mask: 255.255.255.224 *Mar 2 02:12:07.329: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 02:12:07.329: DHCP transaction id: 59E10E1 *Mar 2 02:12:07.329: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 02:12:07.329: Temp default-gateway addr: 180.40.7.132 *Mar 2 02:12:07.329: Next timer fires after: 00:00:00 *Mar 2 02:12:07.329: Retry count: 2 Client-ID: cisco-0001.96de.2580-Fa0/0 *Mar 2 02:12:07.329: Hostname: R4 *Mar 2 02:12:07.333: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 02:12:07.333: DHCP: SRelease: 279 bytes *Mar 2 02:12:07.333: DHCP: Releasing ipl options: *Mar 2 02:12:07.333: Clearing default gateway and route to 180.40.7.132 *Mar 2 02:12:07.333: Removing old default route 180.40.7.132 *Mar 2 02:12:07.337: Clearing DNS address 208.28.1.82 *Mar 2 02:12:07.337: Clearing default domain of cciestudent.com *Mar 2 02:12:08.261: DHCP: SRelease attempt # 3 for entry: *Mar 2 02:12:08.261: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 02:12:08.261: Temp sub net mask: 255.255.255.224 *Mar 2 02:12:08.261: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 02:12:08.261: DHCP transaction id: 59E10E1 *Mar 2 02:12:08.261: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 02:12:08.261: Next timer fires after: 00:00:01 *Mar 2 02:12:08.261: Retry count: 3 Client-ID: cisco-0001.96de.2580-Fa0/0 *Mar 2 02:12:08.261: Hostname: R4 *Mar 2 02:12:08.261: DHCP: R4(config-if)# SRelease placed Server ID option: 180.40.7.129 *Mar 2 02:12:08.265: DHCP: SRelease: 279 bytes *Mar 2 02:12:09.337: RAC: DHCP stopped on interface FastEthernet0/0 *Mar 2 02:12:09.337: DHCP: DHCP client process started: 10 *Mar 2 02:12:09.337: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 02:12:09.337: DHCP: Try 1 to acquire address for FastEthernet0/0 *Mar 2 02:12:09.341: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 02:12:09.341: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 02:12:09.365: DHCP: allocate request *Mar 2 02:12:09.365: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 02:12:09.365: DHCP: new entry. add to queue *Mar 2 02:12:09.369: DHCP: SDiscover attempt # 1 for entry: *Mar 2 02:12:09.369: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 02:12:09.369: Temp sub net mask: 0.0.0.0 *Mar 2 02:12:09.369: DHCP Lease server: 0.0.0.0, state: 1 Selecting *Mar 2 02:12:09.369: DHCP transaction id: 59F7CA9 *Mar 2 02:12:09.369: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 02:12:09.369: Next timer fires after: 00:00:02 *Mar 2 02:12:09.369: Retry count: 1 Client-ID: 0001.96de.2580 *Mar 2 02:12:09.369: Hostname: R4 *Mar 2 02:12:09.369: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 02:12:09.373: DHCP: SDiscover 274 bytes *Mar 2 02:12:09.373: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 02:12:11.381: DHCP: Received a BOOTREP pkt *Mar 2 02:12:11.381: DHCP: Scan: Message type: DHCP Offer *Mar 2 02:12:11.381: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 02:12:11.381: DHCP: Scan: Lease Time: 86400 *Mar 2 02:12:11.381: DHCP: Scan: Renewal time: 43200 *Mar 2 02:12:11.381: DHCP: Scan: Rebind time: 75600 *Mar 2 02:12:11.381: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 02:12:11.381: DHCP: Scan: Router Option: 180.40.7.132 *Mar 2 02:12:11.381: DHCP: Scan: Domain Name: cciestudent.com *Mar 2 02:12:11.381: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 02:12:11.381: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 02:12:11.385: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 02:12:11.385: UDP sport: 43, dport: 44, length: 317 *Mar 2 02:12:11.385: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 02:12:11.385: DHCP server identifier: 180.40.7.129 *Mar 2 02:12:11.385: xid: 59F7CA9, secs: 0, flags: 8000 *Mar 2 02:12:11.385: client: 0.0.0.0, your: 180.40.7.135 *Mar 2 02:12:11.385: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 02:12:11.385: options block length: 69 *Mar 2 02:12:11.385: DHCP Offer Message Offered Address: 180.40.7.135 *Mar 2 02:12:11.385: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 02:12:11.389: DHCP: Server ID Option: 180.40.7.129 *Mar 2 02:12:11.389: DHCP: offer received from 180.40.7.129 *Mar 2 02:12:11.389: DHCP: SRequest attempt # 1 for entry: *Mar 2 02:12:11.389: Temp IP addr: 180.40.7.135 for peer on Interface: FastEthernet0/0 *Mar 2 02:12:11.389: Temp sub net mask: 255.255.255.224 *Mar 2 02:12:11.389: DHCP Lease server: 180.40.7.129, state: 2 Requesting *Mar 2 02:12:11.389: DHCP transaction id: 59F7CA9 *Mar 2 02:12:11.389: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 02:12:11.389: Next timer fires after: 00:00:02 *Mar 2 02:12:11.389: Retry count: 1 Client-ID: 0001.96de.2580 *Mar 2 02:12:11.389: Hostname: R4 *Mar 2 02:12:11.393: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 02:12:11.393: DHCP: SRequest- Requested IP addr option: 180.40.7.135 *Mar 2 02:12:11.393: DHCP: SRequest placed lease len option: 86400 *Mar 2 02:12:11.393: DHCP: SRequest: 292 bytes *Mar 2 02:12:11.393: DHCP: SRequest: 292 bytes *Mar 2 02:12:11.393: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 02:12:11.401: DHCP: Received a BOOTREP pkt *Mar 2 02:12:11.401: DHCP: Scan: Message type: DHCP Ack *Mar 2 02:12:11.401: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 02:12:11.401: DHCP: Scan: Lease Time: 86400 *Mar 2 02:12:11.401: DHCP: Scan: Renewal time: 43200 *Mar 2 02:12:11.401: DHCP: Scan: Rebind time: 75600 *Mar 2 02:12:11.401: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 02:12:11.401: DHCP: Scan: Router Option: 180.40.7.132 *Mar 2 02:12:11.405: DHCP: Scan: Domain Name: cciestudent.com *Mar 2 02:12:11.405: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 02:12:11.405: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 02:12:11.405: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 02:12:11.405: UDP sport: 43, dport: 44, length: 317 *Mar 2 02:12:11.405: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 02:12:11.405: DHCP server identifier: 180.40.7.129 *Mar 2 02:12:11.405: xid: 59F7CA9, secs: 0, flags: 8000 *Mar 2 02:12:11.405: client: 0.0.0.0, your: 180.40.7.135 *Mar 2 02:12:11.405: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 02:12:11.405: options block length: 69 *Mar 2 02:12:11.405: DHCP Ack Message *Mar 2 02:12:11.409: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 02:12:11.409: DHCP: Server ID Option: 180.40.7.129 *Mar 2 02:12:14.417: DHCP: Releasing ipl options: *Mar 2 02:12:14.421: DHCP: Applying DHCP options: *Mar 2 02:12:14.421: Setting default_gateway to 180.40.7.132 *Mar 2 02:12:14.421: Adding default route 180.40.7.132 *Mar 2 02:12:15.421: Adding DNS server address 208.28.1.82 *Mar 2 02:12:15.421: Setting default domain to cciestudent.com *Mar 2 02:12:15.421: DHCP Client Pooling: ***Allocated IP address: 180.40.7.135 *Mar 2 02:12:15.517: Allocated IP address = 180.40.7.135 255.255.255.224 *Mar 2 02:12:15.517: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.135, mask 255.255.255.224, hostname R4 R4(config-if)# R4(config-if)# *Mar 2 02:12:24.429: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 02:12:25.265: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)# RACK99AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#clea ip dhcp bin *sh ip dhcp bin  Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.135 0100.0196.de25.80 Mar 03 1993 02:09 AM Automatic R3#0001.96de.2580 *Mar 2 02:10:22.443: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired R3#0001.96de.2580              confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#ip dhcp pool FroR4R4 R4 oR4rR4 R3(dhcp-config)#har R3(dhcp-config)#hardware-address ? WORD Dotted-hexadecimal string (aabb.ccdd.eeff ...) R3(dhcp-config)#hardware-address                  cl R3(dhcp-config)#client-i  R3(dhcp-config)#client-i R3(dhcp-config)#client-identifier 01  0001.96de.258000001.96de.258010001.96de.2580.0001.96de.25800001.\96de.258096de.2580 96de.2580 0000196de.2580 00.0196de.25800196de.2580 \25802580 .de2580de25.80 R3(dhcp-config)#host ? A.B.C.D IP address in dotted-decimal notation R3(dhcp-config)#host 180.40.7.130 /27 R3(dhcp-config)#^Z R3# *Mar 2 02:13:23.099: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# R3# RACK99AS> [Resuming connection 3 to r3 ... ] R3# R3#clea ip bg  dhcp bin * R3#^Z R3# RACK99AS>4 [Resuming connection 4 to r4 ... ] *M R4(config-if)#ip add dhcp cli fa 0/0 *Mar 2 02:16:40.513: DHCP: SRelease attempt # 1 for entry: *Mar 2 02:16:40.513: Temp IP addr: 180.40.7.135 for peer on Interface: FastEthernet0/0 *Mar 2 02:16:40.513: Temp sub net mask: 255.255.255.224 *Mar 2 02:16:40.513: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 02:16:40.513: DHCP transaction id: 59F7CA9 *Mar 2 02:16:40.513: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 02:16:40.513: Temp default-gateway addr: 180.40.7.132 *Mar 2 02:16:40.513: Next timer fires after: 00:00:01 *Mar 2 02:16:40.513: Retry count: 1 Client-ID: 0001.96de.2580 *Mar 2 02:16:40.513: Hostname: R4 *Mar 2 02:16:40.517: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 02:16:40.517: DHCP: SRelease: 259 bytes *Mar 2 02:16:40.581: DHCP: SRelease attempt # 2 for entry: *Mar 2 02:16:40.581: Temp IP addr: 180.40.7.135 for peer on Interface: FastEthernet0/0 *Mar 2 02:16:40.581: Temp sub net mask: 255.255.255.224 *Mar 2 02:16:40.581: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 02:16:40.581: DHCP transaction id: 59F7CA9 *Mar 2 02:16:40.581: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 02:16:40.581: Temp default-gateway addr: 180.40.7.132 *Mar 2 02:16:40.581: Next timer fires after: 00:00:00 *Mar 2 02:16:40.581: Retry count: 2 Client-ID: 0001.96de.2580 *Mar 2 02:16:40.581: Hostname: R4 *Mar 2 02:16:40.585: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 02:16:40.585: DHCP: SRelease: 259 bytes *Mar 2 02:16:40.585: DHCP: Releasing ipl options: *Mar 2 02:16:40.585: Clearing default gateway and route to 180.40.7.132 *Mar 2 02:16:40.585: Removing old default route 180.40.7.132 *Mar 2 02:16:40.589: Clearing DNS address 208.28.1.82 *Mar 2 02:16:40.589: Clearing default domain of cciest R4(config-if)#udent.com *Mar 2 02:16:41.513: DHCP: SRelease attempt # 3 for entry: *Mar 2 02:16:41.513: Temp IP addr: 180.40.7.135 for peer on Interface: FastEthernet0/0 *Mar 2 02:16:41.513: Temp sub net mask: 255.255.255.224 *Mar 2 02:16:41.513: DHCP Lease server: 180.40.7.129, state: 7 Releasing *Mar 2 02:16:41.513: DHCP transaction id: 59F7CA9 *Mar 2 02:16:41.513: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 02:16:41.513: Next timer fires after: 00:00:01 *Mar 2 02:16:41.513: Retry count: 3 Client-ID: 0001.96de.2580 *Mar 2 02:16:41.513: Hostname: R4 *Mar 2 02:16:41.513: DHCP: SRelease placed Server ID option: 180.40.7.129 *Mar 2 02:16:41.517: DHCP: SRelease: 259 bytes *Mar 2 02:16:42.589: RAC: DHCP stopped on interface FastEthernet0/0 *Mar 2 02:16:42.589: DHCP: DHCP client process started: 10 *Mar 2 02:16:42.589: RAC: Starting DHCP discover on FastEthernet0/0 *Mar 2 02:16:42.589: DHCP: Try 1 to acquire address for FastEthernet0/0 *Mar 2 02:16:42.593: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 02:16:42.593: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 02:16:42.617: DHCP: allocate request *Mar 2 02:16:42.617: DHCP: zapping entry in DHC_PURGING state for Fa0/0 *Mar 2 02:16:42.617: DHCP: new entry. add to queue *Mar 2 02:16:42.621: DHCP: SDiscover attempt # 1 for entry: *Mar 2 02:16:42.621: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/0 *Mar 2 02:16:42.621: Temp sub net mask: 0.0.0.0 *Mar 2 02:16:42.621: DHCP Lease server: 0.0.0.0, state: 1 Selecting *Mar 2 02:16:42.621: DHCP transaction id: 5A3A29A *Mar 2 02:16:42.621: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 02:16:42.621: Next timer fires after: 00:00:03 *Mar 2 02:16:42.621: Retry count: 1 Client-ID: 0001.96de.2580 *Mar 2 02:16:42.621: Hostname: R4 *Mar 2 02:16:42.621: DHCP: SDiscover: sending 274 byte length DHCP packet *Mar 2 02:16:42.625: DHCP: SDiscover 274 bytes *Mar 2 02:16:42.625: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 02:16:42.633: DHCP: Received a BOOTREP pkt *Mar 2 02:16:42.633: DHCP: Scan: Message type: DHCP Offer *Mar 2 02:16:42.633: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 02:16:42.633: DHCP: Scan: Lease Time: 86400 *Mar 2 02:16:42.633: DHCP: Scan: Renewal time: 43200 *Mar 2 02:16:42.633: DHCP: Scan: Rebind time: 75600 *Mar 2 02:16:42.637: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 02:16:42.637: DHCP: Scan: Router Option: 180.40.7.132 *Mar 2 02:16:42.637: DHCP: Scan: Domain Name: cciestudent.com *Mar 2 02:16:42.637: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 02:16:42.637: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 02:16:42.637: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 02:16:42.637: UDP sport: 43, dport: 44, length: 317 *Mar 2 02:16:42.637: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 02:16:42.637: DHCP server identifier: 180.40.7.129 *Mar 2 02:16:42.637: xid: 5A3A29A, secs: 0, flags: 8000 *Mar 2 02:16:42.637: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 02:16:42.641: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 02:16:42.641: options block length: 69 *Mar 2 02:16:42.641: DHCP Offer Message Offered Address: 180.40.7.130 *Mar 2 02:16:42.641: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 02:16:42.641: DHCP: Server ID Option: 180.40.7.129 *Mar 2 02:16:42.641: DHCP: offer received from 180.40.7.129 *Mar 2 02:16:42.641: DHCP: SRequest attempt # 1 for entry: *Mar 2 02:16:42.641: Temp IP addr: 180.40.7.130 for peer on Interface: FastEthernet0/0 *Mar 2 02:16:42.641: Temp sub net mask: 255.255.255.224 *Mar 2 02:16:42.641: DHCP Lease server: 180.40.7.129, state: 2 Requesting *Mar 2 02:16:42.645: DHCP transaction id: 5A3A29A *Mar 2 02:16:42.645: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs *Mar 2 02:16:42.645: Next timer fires after: 00:00:01 *Mar 2 02:16:42.645: Retry count: 1 Client-ID: 0001.96de.2580 *Mar 2 02:16:42.645: Hostname: R4 *Mar 2 02:16:42.645: DHCP: SRequest- Server ID option: 180.40.7.129 *Mar 2 02:16:42.645: DHCP: SRequest- Requested IP addr option: 180.40.7.130 *Mar 2 02:16:42.645: DHCP: SRequest placed lease len option: 86400 *Mar 2 02:16:42.645: DHCP: SRequest: 292 bytes *Mar 2 02:16:42.645: DHCP: SRequest: 292 bytes *Mar 2 02:16:42.649: B'cast on FastEthernet0/0 interface from 0.0.0.0 *Mar 2 02:16:42.653: DHCP: Received a BOOTREP pkt *Mar 2 02:16:42.653: DHCP: Scan: Message type: DHCP Ack *Mar 2 02:16:42.653: DHCP: Scan: Server ID Option: 180.40.7.129 = B4280781 *Mar 2 02:16:42.653: DHCP: Scan: Lease Time: 86400 *Mar 2 02:16:42.657: DHCP: Scan: Renewal time: 43200 *Mar 2 02:16:42.657: DHCP: Scan: Rebind time: 75600 *Mar 2 02:16:42.657: DHCP: Scan: Subnet Address Option: 255.255.255.224 *Mar 2 02:16:42.657: DHCP: Scan: Router Option: 180.40.7.132 *Mar 2 02:16:42.657: DHCP: Scan: Domain Name: cciestudent.com *Mar 2 02:16:42.657: DHCP: Scan: DNS Name Server Option: 208.28.1.82 *Mar 2 02:16:42.657: DHCP: Scan: TFTP Server address Option: 20.20.20.20 *Mar 2 02:16:42.657: DHCP: rcvd pkt source: 180.40.7.129, destination: 255.255.255.255 *Mar 2 02:16:42.657: UDP sport: 43, dport: 44, length: 317 *Mar 2 02:16:42.657: DHCP op: 2, htype: 1, hlen: 6, hops: 0 *Mar 2 02:16:42.657: DHCP server identifier: 180.40.7.129 *Mar 2 02:16:42.661: xid: 5A3A29A, secs: 0, flags: 8000 *Mar 2 02:16:42.661: client: 0.0.0.0, your: 180.40.7.130 *Mar 2 02:16:42.661: srvr: 0.0.0.0, gw: 0.0.0.0 *Mar 2 02:16:42.661: options block length: 69 *Mar 2 02:16:42.661: DHCP Ack Message *Mar 2 02:16:42.661: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 *Mar 2 02:16:42.661: DHCP: Server ID Option: 180.40.7.129 *Mar 2 02:16:45.669: DHCP: Releasing ipl options: *Mar 2 02:16:45.673: DHCP: Applying DHCP options: *Mar 2 02:16:45.673: Setting default_gateway to 180.40.7.132 *Mar 2 02:16:45.673: Adding default route 180.40.7.132 *Mar 2 02:16:46.673: Adding DNS server address 208.28.1.82 *Mar 2 02:16:46.673: Setting default domain to cciestudent.com *Mar 2 02:16:46.673: DHCP Client Pooling: ***Allocated IP address: 180.40.7.130 *Mar 2 02:16:46.721: Allocated IP address = 180.40.7.130 255.255.255.224 *Mar 2 02:16:46.721: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.224, hostname R4 R4(config-if)# R4(config-if)# *Mar 2 02:16:55.281: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 02:16:55.285: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)# *Mar 2 02:17:12.513: DHCP: QScan: Purging entry *Mar 2 02:17:12.513: DHCP: deleting entry 630532D4 0.0.0.0 from list *Mar 2 02:17:12.513: Temp IP addr: 0.0.0.0 for peer on Interface: unknown *Mar 2 02:17:12.513: Temp sub net mask: 255.255.255.224 *Mar 2 02:17:12.513: DHCP Lease server: 180.40.7.129, state: 8 Purging *Mar 2 02:17:12.513: DHCP transaction id: 59F7CA9 *Mar 2 02:17:12.513: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs *Mar 2 02:17:12.513: Temp default-gateway addr: 180.40.7.132 *Mar 2 02:17:12.513: No timer running *Mar 2 02:17:12.513: Retry count: 0 Client-ID: *Mar 2 02:17:12.513: Hostname: R4 R4(config-if)#^Z R4# *Mar 2 02:17:31.273: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4# R4# R4# R4#sh ip   route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 180.40.7.132 to network 0.0.0.0 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 00:00:23, FastEthernet0/0 [110/793] via 180.40.7.131, 00:00:23, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.129, 00:00:23, FastEthernet0/0 [110/783] via 180.40.7.131, 00:00:23, FastEthernet0/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:00:23, FastEthernet0/0 180.40.0.0/27 is subnetted, 4 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 O 180.40.7.160 [110/782] via 180.40.7.131, 00:00:24, FastEthernet0/0 O 180.40.7.0 [110/782] via 180.40.7.129, 00:00:24, FastEthernet0/0 O 180.40.7.64 [110/782] via 180.40.7.131, 00:00:24, FastEthernet0/0 --More--   [110/782] via 180.40.7.129, 00:00:24, FastEthernet0/0 S* 0.0.0.0/0 [254/0] via 180.40.7.132 R4# R4# R4# RACK99AS>3 [Resuming connection 3 to r3 ... ] *M R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int fa 0/0 R3(config-if)#ip addd p    pool ? WORD Pool name R3(config-if)#ip add pool Prob15 R3(config-if)# *Mar 2 02:17:07.095: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 02:17:07.095: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 02:17:07.095: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Active -> Init *Mar 2 02:17:07.099: %VRRP-6-STATECHANGE: Fa0/0 Grp 47 state Master -> Disable R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#do sh ip inbt  t brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned NO manual up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 180.40.7.66 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.1 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--   R3(config-if)#do s h  h run int fa 0/0 Building configuration... Current configuration : 351 bytes ! interface FastEthernet0/0 ip address pool Prob15 ip policy route-map Prob1 duplex auto speed auto vrrp 47 ip 180.40.7.133 vrrp 47 priority 150 standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 standby 47 track 3 decrement 60 service-policy input test end R3(config-if)#ip add dhcp R3(config-if)#ip add dhcp cli R3(config-if)#ip add dhcp client-id ? FastEthernet FastEthernet IEEE 802.3 Port-channel Ethernet Channel of interfaces R3(config-if)#ip add dhcp client-id fa 0/0 ? hostname Specify value for hostname option R3(config-if)#ip add dhcp client-id fa 0/0 R3(config-if)#end R3# *Mar 2 02:18:14.169: %SYS-5-CONFIG_I: Configured from console by console R3#sh int fa 0/0 FastEthernet0/0 is up, line protocol is up Hardware is AmdFE, address is 0012.7f8d.1ea0 (bia 0012.7f8d.1ea0) Internet address will be negotiated using DHCP MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 1 packets/sec 5 minute output rate 2000 bits/sec, 0 packets/sec 38746 packets input, 4134251 bytes Received 28388 broadcasts, 0 runts, 0 giants, 0 throttles 1 input errors, 0 CRC, 0 frame, 0 overrun, 1 ignored 0 watchdog 0 input packets with dribble condition detected 43944 packets output, 4119876 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets --More--   R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip dhcp[    pool ForR3 R3(dhcp-config)#cli R3(dhcp-config)#client-e R3(dhcp-config)#client-e  R3(dhcp-config)#client-i R3(dhcp-config)#client-identifier 010012.7f8d.1ea0.12.7f8d.1ea012.7f8d.1ea0 7f.8d.1ea08d.1ea0 1e.a0 R3(dhcp-config)#host 180.40.7.129 /27 R3(dhcp-config)#^Z R3# *Mar 2 02:19:06.555: %SYS-5-CONFIG_I: Configured from console by console R3# RACK99AS>7 [Resuming connection 7 to r7 ... ] *M R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int fa 0/1 R7(config-if)#ip dhc ? relay DHCP relay configuration parameters R7(config-if)#ip dhc re ? information DHCP relay information option R7(config-if)#ip dhc re in ? trusted Received DHCP packet may contain relay info option with zero giaddr R7(config-if)#ip dhc re in tr ? R7(config-if)#ip dhc re in tr                 ip help R7(config-if)#ip helper-address ? A.B.C.D IP destination address global Helper-address is global vrf VRF name for helper-address (if different from interface VRF) R7(config-if)#ip helper-address 180.40.7.66 R7(config-if)#^Z R7# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3# R3# R3# R3#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES DHCP up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 180.40.7.66 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.1 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--   R3#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES DHCP up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 180.40.7.66 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.1 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--   R3#sh    confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int fa 0/1 0 R3(config-if)#int fa 0/0host 180.40.7.129 /27client-identifier 0100.127f.8d1e.a0ip dhcp pool ForR3 end  *Mar 2 02:21:11.551: %VRRP-6-STATECHANGE: Fa0/0 Grp 47 state Init -> Backup *Mar 2 02:21:11.555: %VRRP-6-STATECHANGE: Fa0/0 Grp 47 state Backup -> Disable *Mar 2 02:21:11.555: %VRRP-6-STATECHANGE: Fa0/0 Grp 47 state Init -> Backup R3(config-if)#endip add dhcp client-id fa 0/0 end ip dhcp pool ForR3client-identifier 0100.127f.8d1e.a0host 180.40.7.129 /27  *Mar 2 02:21:12.629: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.129, mask 255.255.255.224, hostname R3 R3(config-if)#host 180.40.7.129 /27int fa 0/0   *Mar 2 02:21:13.747: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Listen -> Active R3(config-if)# *Mar 2 02:21:14.973: %VRRP-6-STATECHANGE: Fa0/0 Grp 47 state Backup -> Master R3(config-if)#^Z R3# *Mar 2 02:21:16.928: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 2 02:21:17.734: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# R3# R3#confi t *Mar 2 02:21:18.807: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R3#confi tsh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.129 YES DHCP up up BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 180.40.7.66 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.1 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--   R3#sh run int       | b ip dhcp ip dhcp excluded-address 180.40.7.131 180.40.7.134 ! ip dhcp pool Prob15 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 domain-name cciestudent.com dns-server 208.28.1.82 option 150 ip 20.20.20.20 ! ip dhcp pool ForR4 host 180.40.7.130 255.255.255.224 client-identifier 0100.0196.de25.80 ! ip dhcp pool ForR3 host 180.40.7.129 255.255.255.224 client-identifier 0100.127f.8d1e.a0 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! --More--  ! ! ! ! ! ! ! ! ! ! ! ! ! track 3 ip route 20.10.2.0 255.255.255.0 reachability ! ! ! class-map match-all dscp26 match dscp af31 class-map match-all dscp14 match dscp af13 class-map match-all telnet match protocol telnet --More--  class-map match-all ef match dscp ef class-map match-all dscp12 match dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match protocol ftp ! ! policy-map test class dscp12 class dscp14 class dscp26 class dscp28 class prec3 class ef policy-map Prob711 class dscp12 priority percent 25 class telnet --More--   bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address dhcp client-id FastEthernet0/0 ip policy route-map Prob1 duplex auto speed auto vrrp 47 ip 180.40.7.133 vrrp 47 priority 150 standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 --More--   standby 47 track 3 decrement 60 --More--   service-policy input test --More--  ! --More--   R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 180.40.7.132 to network 0.0.0.0 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:01:49, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.2, 00:01:49, Serial1/2 [110/792] via 180.40.7.67, 00:01:49, Serial1/0 O 20.10.1.0 [110/782] via 180.40.7.67, 00:01:49, Serial1/0 [110/782] via 180.40.7.2, 00:01:49, Serial1/2 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:01:49, FastEthernet0/0 180.40.0.0/27 is subnetted, 4 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 O 180.40.7.160 [110/782] via 180.40.7.131, 00:01:50, FastEthernet0/0 C 180.40.7.0 is directly connected, Serial1/2 C 180.40.7.64 is directly connected, Serial1/0 --More--  S* 0.0.0.0/0 [254/0] via 180.40.7.132 R3#sh stan FastEthernet0/0 - Group 47 State is Active 10 state changes, last state change 00:02:19 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 1.658 secs Preemption enabled Active router is local Standby router is 180.40.7.131, priority 100 (expires in 9.575 sec) Priority 150 (configured 150) Track interface Serial1/0 state Up decrement 51 Track interface Serial1/2 state Up decrement 51 Track object 3 state Up decrement 60 IP redundancy name is "hsrp-Fa0/0-47" (default) R3# RACK99AS>7 [Resuming connection 7 to r7 ... ] * R7#sh run int fa 0/1 Building configuration... Current configuration : 232 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 ip helper-address 180.40.7.66 speed auto half-duplex vrrp 47 ip 180.40.7.133 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 end R7# R7# RACK99AS>2 [Resuming connection 2 to r2 ... ] *M R2#conif t ^ % Invalid input detected at '^' marker. R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#int fa 0/1 R2(config-if)#ip help   R2(config-if)#ip helper-address 208.28.1.99 R2(config-if)#exit R2(config)#ip dhcp pool test R2(dhcp-config)#20.10     netw 20.10.1.2 /24 R2(dhcp-config)#exi    RACK99AS>6 [Resuming connection 6 to r6 ... ] S6#coni fig t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/2 S6(config-if)#ip dhcp    addd    d hdcp ^ % Invalid input detected at '^' marker. S6(config-if)#ip add hdcp    dhcp S6(config-if)# 1d02h: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on FastEthernet0/2 from FULL to DOWN, Neighbor Down: Interface down or detached S6(config-if)#Interface FastEthernet0/2 assigned DHCP address 20.10.1.2, mask 255.255.255.0 S6(config-if)# S6(config-if)# S6(config-if)# S6(config-if)# RACK99AS>2 [Resuming connection 2 to r2 ... ] R2(dhcp-config)#do sh ip dhcp *Mar 2 02:31:54.778: %OSPF-5-ADJCHG: Process 1, Nbr 20.10.2.1 on FastEthernet0/1 from LOADING to FULL, Loading Done R2(dhcp-config)#do sh ip dhcp bin % Ambiguous command: "do sh ip dhcp bin" R2(config)#do sh ip dhcp bind Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 20.10.1.2 0063.6973.636f.2d30. Mar 03 1993 02:31 AM Automatic 3031.322e.3766.3532. 2e31.3138.302d.4661. 302f.32 R2(config)#do sh ip dhcp bind netw 20.10.1.2 /24do sh ip dhcp bin netw 20.10.1.2 /24ip dhcp pool test nip dhcp pool testoip dhcp pool test ip dhcp pool test R2(config)#ip dhcp pool S6 R2(dhcp-config)#clie R2(dhcp-config)#client-i R2(dhcp-config)#client-identifier 0063.6973.636f.2d30.3031.322e.3766.3532.2e3$tifier 0063.6973.636f.2d30.3031.322e.3766.3532.2e31 .3138.3023.6973.636f.2d30.3031.322e.3766.3532.2e31.3138.302d .4661.302f.2d30.3031.322e.3766.3532.2e31.3138.302d.4661.302f .32 R2(dhcp-config)#host 20.10.1.2 /24 R2(dhcp-config)#^Z R2# *Mar 2 02:33:25.078: %S RACK99AS>6 [Resuming connection 6 to r6 ... ] 1d S6(config-if)#ip add 20.10.1.2 254 5.255.255.0 S6(config-if)#^Z S6# 1d02h: %SYS-5-CONFIG_I: Configured from console by console S6# S6# S6# S6# S6# RACK99AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0.2 R7(config-subif)# R7(config-subif)#ip help 208.28.1.99 R7(config-subif)#do sh in  t s 1/0.2 Serial1/0.2 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is 180.40.7.161/27 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never R7(config-subif)#do sh int s 1/0.2rint s 1/0.2uint s 1/0.2nint s 1/0.2 int s 1/0.2 Building configuration... Current configuration : 202 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 end R7(config-subif)# frame-relay interface-dlci 702 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R7(config-subif)# frame-relay interface-dlci 702 pro R7(config-subif)# frame-relay interface-dlci 702 protocol ? A.B.C.D Protocol specific address ip IP R7(config-subif)# frame-relay interface-dlci 702 protocol 180.40.7.162 %Can't add another VC to point-to-point subinterface R7(config-fr-dlci)#no frame-relay interface-dlci 702 R7(config-subif)#no frame-relay interface-dlci 702 frame-relay interface-dlci 702 protocol 180.40.7.162 *Mar 1 22:37:16.868: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-subif)# frame-relay interface-dlci 702 protocol 180.40.7.162 R7(config-fr-dlci)# *Mar 1 22:37:21.628: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7(config-fr-dlci)#^Z R7# *Mar 1 22:37:24.633: %SYS-5-CONFIG_I: Configured from console by console R7# R7# R7# R7# R7# R7#sh run int fa 0/0 Building configuration... Current configuration : 95 bytes ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex end R7#sh run int fa 0/0      s1/0.2 Building configuration... Current configuration : 224 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 end R7# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b dhcp ip dhcp excluded-address 180.40.7.131 180.40.7.134 ! ip dhcp pool Prob15 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 domain-name cciestudent.com dns-server 208.28.1.82 option 150 ip 20.20.20.20 ! ip dhcp pool ForR4 host 180.40.7.130 255.255.255.224 client-identifier 0100.0196.de25.80 ! ip dhcp pool ForR3 host 180.40.7.129 255.255.255.224 client-identifier 0100.127f.8d1e.a0 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! --More--   R3# RACK99AS>2 [Resuming connection 2 to r2 ... ] YS-5-CONFIG_I: Configured from console by console R2# R2#sh run int     | b dhcp ip dhcp pool S6 host 20.10.1.2 255.255.255.0 client-identifier 0063.6973.636f.2d30.3031.322e.3766.3532.2e31.3138.302d.4661.302f.32 ! ip cef no ip domain lookup ip audit po max-events 100 frame-relay de-list 1 protocol ip list 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! --More--  ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto ! interface Serial1/0 --More--   R2#