=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.11.29 06:10:43 =~=~=~=~=~=~=~=~=~=~=~= RACK99AS>7 [Resuming connection 7 to r7 ... ] R7#confi g t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int fa 0/1 R7(config-if)#gl R7(config-if)#glbp ? <0-1023> Group number R7(config-if)#glbp 47 ip ? A.B.C.D Virtual IP address R7(config-if)#glbp 47 ip 180.40.7.134 R7(config-if)#^Z R7#sh gl *Mar 2 14:10:13.558: %SYS-5-CONFIG_I: Configured from console by console R7#sh gl FastEthernet0/1 - Group 47 State is Speak Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.525 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is unknown Standby is unknown Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There are no forwarders R7# *Mar 2 14:10:24.463: %GLBP-6-STATECHANGE: FastEthernet0/1 Grp 47 state Standby -> Active R7# *Mar 2 14:10:34.464: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 47 Fwd 1 state Listen -> Active R7#sh gl FastEthernet0/1 - Group 47 State is Active 2 state changes, last state change 00:00:44 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.027 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is unknown Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Load balancing: round-robin There is 1 forwarder (1 active) Forwarder 1 State is Active 1 state change, last state change 00:00:34 MAC address is 0007.b400.2f01 (default) Owner ID is 0012.7f80.f441 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#trac R7(config)#track ? <1-500> Tracked object resolution Tracking resolution parameters timer Polling interval timers R7(config)#track 1 ? interface Select an interface to track ip IP protocol R7(config)#track 1 ip ? route IP route R7(config)#track 1 ip rou ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R7(config)#track 1 ip rou 20.10.1.0/24 ? metric Route metric reachability Route reachability state R7(config)#track 1 ip rou 20.10.1.0/24 re R7(config)#track 1 ip rou 20.10.1.0/24 reachability R7(config-track)#int fa 0/1 R7(config-if)#gl R7(config-if)#glbp 47 tr R7(config-if)#glbp 47 tr  ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R7(config-if)#glbp 47 we R7(config-if)#glbp 47 weighting ? <1-254> Weighting maximum value track Interface tracking R7(config-if)#glbp 47 weighting tr R7(config-if)#glbp 47 weighting track ? <1-500> Tracked object R7(config-if)#glbp 47 weighting track 1 ? decrement Weighting decrement R7(config-if)#glbp 47 weighting track 1 dec R7(config-if)#glbp 47 weighting track 1 decrement ? <1-255> Decrement value R7(config-if)#glbp 47 weighting track 1 decrement 100 R7(config-if)#^Z R7#sh *Mar 2 14:18:13.228: %SYS-5-CONFIG_I: Configured from console by console R7#sh gl FastEthernet0/1 - Group 47 State is Active 2 state changes, last state change 00:07:51 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.463 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is unknown Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 1 state Up decrement 100 Load balancing: round-robin There is 1 forwarder (1 active) Forwarder 1 State is Active 1 state change, last state change 00:07:41 MAC address is 0007.b400.2f01 (default) Owner ID is 0012.7f80.f441 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 R7# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int     do sh run | b track track 3 ip route 20.10.2.0 255.255.255.0 reachability ! ! ! class-map match-all dscp26 match dscp af31 class-map match-all dscp14 match dscp af13 class-map match-all telnet match protocol telnet class-map match-all ef match dscp ef class-map match-all dscp12 match dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match protocol ftp ! ! policy-map test --More--   R3(config)#tra R3(config)#trak R3(config)#trak c 4 ip rout 10  20.10.1.0/24 re R3(config)#trac 4 ip rout 20.10.1.0/24 reachability R3(config-track)#exit R3(config)#int f 0/0 R3(config-if)#gl R3(config-if)#glbp 47 ip 180.40.7.134 R3(config-if)#gl R3(config-if)#glbp 47 w R3(config-if)#glbp 47 weighting ? <1-254> Weighting maximum value track Interface tracking R3(config-if)#glbp 47 weighting 4 ? lower Weighting lower threshold upper Weighting upper threshold R3(config-if)#glbp 47 weighting 4     tr R3(config-if)#glbp 47 weighting track 4 de R3(config-if)#glbp 47 weighting track 4 decrement 10 R3(config-if)# *Mar 2 18:20:27.113: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 47 Fwd 2 state Listen -> Active R3(config-if)#glbp 47 weighting track 4 decrement 100 R3(config-if)#do sh run int f 0/0 Building configuration... Current configuration : 436 bytes ! interface FastEthernet0/0 ip address dhcp client-id FastEthernet0/0 ip policy route-map Prob1 duplex auto speed auto vrrp 47 ip 180.40.7.133 vrrp 47 priority 150 glbp 47 ip 180.40.7.134 glbp 47 weighting track 4 decrement 100 standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 standby 47 track 3 decrement 60 service-policy input test end R3(config-if)#q do sh run int f 0/0   glbp 47 weighting track 4 decrement 100               1 ? decrement Weighting decrement R3(config-if)#glbp 47 weighting track 1 dec R3(config-if)#glbp 47 weighting track 1 decrement 100 decrement 100 2 decrement 100 R3(config-if)#^Z R3# *Mar 2 18:21:20.364: %SYS-5-CONFIG_I: Configured from console by console R3#sh gl FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:00:55 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.654 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 7.813 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 2 state Up decrement 100 Track object 4 state Up decrement 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0012.7f80.f441 Time to live: 14397.809 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.809 sec) --More--   Forwarder 2 State is Active 1 state change, last state change 00:01:37 MAC address is 0007.b400.2f02 (default) Owner ID is 0012.7f8d.1ea0 Preemption enabled, min delay 30 sec Active is local, weighting 100 R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int f 0/0 R3(config-if)#gl R3(config-if)#glbp 47 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R3(config-if)#glbp 47 tim R3(config-if)#glbp 47 timers ? <1-60> Hello interval in seconds msec Specify hello interval in milliseconds redirect Specify time-out values for failed forwarders R3(config-if)#glbp 47 timers re R3(config-if)#glbp 47 timers redirect ? <0-3600> Interval in seconds to redirect to failed forwarders R3(config-if)#glbp 47 timers redirect                         ^Z R3# *Mar 2 18:26:49.203: %SYS-5-CONFIG_I: Configured from console by console R3# RACK99AS>2 [Resuming connection 2 to r2 ... ] R2#conf Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#shut R2(config-if)# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3# *Mar 2 18:26:59.652: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Active -> Speak *Mar 2 18:27:00.602: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down R3# R3# *Mar 2 18:27:00.602: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 18:27:01.604: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3# R3# R3# R3#sh gl FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:06:35 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.520 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 9.684 sec) Standby is local Priority 100 (default) Weighting 0, low (default 100), thresholds: lower 1, upper 100 Track object 2 state Down decrement 100 Track object 4 state Up decrement 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0012.7f80.f441 Time to live: 14399.680 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.676 sec) --More--   Forwarder 2 State is Active 1 state change, last state change 00:06:44 MAC address is 0007.b400.2f02 (default) Owner ID is 0012.7f8d.1ea0 Preemption enabled, min delay 30 sec Active is local, weighting 0 R3# RACK99AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh gl FastEthernet0/1 - Group 47 State is Active 2 state changes, last state change 00:16:17 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.884 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.129, priority 100 (expires in 8.718 sec) Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 1 state Up decrement 100 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:16:07 MAC address is 0007.b400.2f01 (default) Owner ID is 0012.7f80.f441 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 --More--   Forwarder 2 State is Listen MAC address is 0007.b400.2f02 (learnt) Owner ID is 0012.7f8d.1ea0 Redirection enabled, 598.025 sec remaining (maximum 600 sec) Time to live: 14398.021 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec (4 secs remaining) Active is 180.40.7.129 (primary), weighting 0, low (expires in 8.021 sec) R7# *Mar 2 14:26:46.609: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 47 Fwd 2 state Listen -> Active R7# RACK99AS>3 [Resuming connection 3 to r3 ... ] *M R3# RACK99AS>2 [Resuming connection 2 to r2 ... ] * R2(config-if)#nb  no shut R2(config-if)#^Z R2# RACK99AS>3 [Resuming connection 3 to r3 ... ] R3# *Mar 2 18:28:11.122: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 2 18:28:11.679: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active R3#sh gl FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:07:39 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 0.087 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 9.255 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 2 state Up decrement 100 Track object 4 state Up decrement 100 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0012.7f80.f441 Time to live: 14399.247 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 9.243 sec) --More-- *Mar 2 18:28:12.127: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up --More--   Forwarder 2 State is Listen 2 state changes, last state change 00:00:44 MAC address is 0007.b400.2f02 (default) Owner ID is 0012.7f8d.1ea0 Preemption enabled, min delay 30 sec (26 secs remaining) Active is 180.40.7.131 (secondary), weighting 100 (expires in 9.940 sec) R3#sh gl *Mar 2 18:28:21.258: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from LOADING to FULL, Loading Done R3#sh gl FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:07:49 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 2.002 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 8.161 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 2 state Up decrement 100 Track object 4 state Up decrement 100 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0012.7f80.f441 Time to live: 14398.157 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 8.153 sec) --More--   Forwarder 2 State is Listen 2 state changes, last state change 00:00:53 MAC address is 0007.b400.2f02 (default) Owner ID is 0012.7f8d.1ea0 Preemption enabled, min delay 30 sec (17 secs remaining) Active is 180.40.7.131 (secondary), weighting 100 (expires in 9.760 sec) R3#sh gl FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:07:58 Virtual IP address is 180.40.7.134 Hello time 3 sec, hold time 10 sec Next hello sent in 1.398 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.131, priority 100 (expires in 7.552 sec) Standby is local Priority 100 (default) Weighting 100 (default 100), thresholds: lower 1, upper 100 Track object 2 state Up decrement 100 Track object 4 state Up decrement 100 Load balancing: round-robin There are 2 forwarders (0 active) Forwarder 1 State is Listen MAC address is 0007.b400.2f01 (learnt) Owner ID is 0012.7f80.f441 Time to live: 14397.548 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.548 sec) --More--   Forwarder 2 State is Listen 2 state changes, last state change 00:01:03 MAC address is 0007.b400.2f02 (default) Owner ID is 0012.7f8d.1ea0 Preemption enabled, min delay 30 sec (7 secs remaining) Active is 180.40.7.131 (secondary), weighting 100 (expires in 8.469 sec) R3# *Mar 2 18:28:42.425: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 47 Fwd 2 state Listen -> Active R3#sh gl bri Interface Grp Fwd Pri State Address Active router Standby router Fa0/0 47 - 100 Standby 180.40.7.134 180.40.7.131 local Fa0/0 47 1 7 Listen 0007.b400.2f01 180.40.7.131 - Fa0/0 47 2 7 Active 0007.b400.2f02 local - R3#sh gl bri bri  bri s brit bria brin bri P indicates configured to preempt. | Interface Grp Prio P State Active Standby Virtual IP Fa0/0 47 150 P Active local 180.40.7.131 180.40.7.132 R3#sh stan bri bri  bri  bri  bri v brir brir brip bri Interface Grp Pri Time Own Pre State Master addr Group addr Fa0/0 47 150 3414 Y Master 180.40.7.129 180.40.7.133 R3#sh run int     | b track track 3 ip route 20.10.2.0 255.255.255.0 reachability ! track 4 ip route 20.10.1.0 255.255.255.0 reachability ! ! ! class-map match-all dscp26 match dscp af31 class-map match-all dscp14 match dscp af13 class-map match-all telnet match protocol telnet class-map match-all ef match dscp ef class-map match-all dscp12 match dscp af12 class-map match-all dscp28 match dscp af32 class-map match-all prec3 match ip precedence 3 class-map match-all ftp match protocol ftp ! --More--  ! policy-map test class dscp12 class dscp14 class dscp26 class dscp28 class prec3 class ef policy-map Prob711 class dscp12 priority percent 25 class telnet bandwidth remaining percent 24 class ftp bandwidth remaining percent 51 class class-default bandwidth remaining percent 25 ! ! ! ! ! ! --More--  interface FastEthernet0/0 ip address dhcp client-id FastEthernet0/0 ip policy route-map Prob1 duplex auto speed auto vrrp 47 ip 180.40.7.133 vrrp 47 priority 150 glbp 47 ip 180.40.7.134 glbp 47 weighting track 2 decrement 100 glbp 47 weighting track 4 decrement 100 standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/0 51 standby 47 track Serial1/2 51 standby 47 track 3 decrement 60 service-policy input test ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 --More--   R3# RACK99AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh run | b track track 1 ip route 20.10.1.0 255.255.255.0 reachability ! ! ! class-map match-all S5Other match access-group name S5 class-map match-all S5Telnet match access-group name S5 match protocol telnet class-map match-any JPG match protocol http url "*.jpg" match protocol http url "*.jpe" match protocol http url "*.jpeg" match protocol http mime "*jpeg" match protocol http mime "*jpe" match protocol http mime "*jpg" ! ! policy-map Prob5 class JPG shape average 1000000 class S5Telnet bandwidth 1000 --More--   class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 class class-default ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 ip helper-address 180.40.7.66 speed auto --More--   half-duplex vrrp 47 ip 180.40.7.133 glbp 47 ip 180.40.7.134 glbp 47 weighting track 1 decrement 100 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 ! interface Serial1/0 no ip address encapsulation frame-relay frame-relay interface-queue priority ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 --More--   R7# RACK99AS>6 [Resuming connection 6 to r6 ... ] S6#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   S6#confit Translating "confit" % Unknown command or computer name, or unable to find computer address S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#mls qos map dscp cos       S6(config)#mls qos map dscp-c S6(config)#mls qos map dscp-cos ? <0-63> DSCP values separated by spaces (up to 8 values total) S6(config)#mls qos map dscp-cos 8 9 11 13 15 to 2 S6(config)#mls qos map dsc S6(config)#mls qos map dscp-c S6(config)#mls qos map dscp-cos 24 25 27 29 31 to 2 S6(config)#do sh mls qos map dscp-co Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 02 02 1 : 01 02 01 02 01 02 02 02 02 02 2 : 02 02 02 02 02 02 03 02 03 02 3 : 03 02 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 S6(config)#int g i 0/1 ^ % Invalid input detected at '^' marker. S6(config)#int g i 0/1i 0/1  S6(config-if)#wrr S6(config-if)#wrr-queue ? bandwidth Configure WRR bandwidth cos-map Configure cos-map for a queue id dscp-map Configure dscp-map for a queue threshold queue-limit Configure queue-limit random-detect Configure random-detect threshold Configure queue tail-drop thresholds S6(config-if)#wrr-queue co S6(config-if)#wrr-queue cos-map ? <1-4> enter cos-map queue id S6(config-if)#wrr-queue cos-map 2 0 4 5 6 7 S6(config-if)#wrr-queue cos-map 2 0 4 5 6 7           3 3 S6(config-if)#do sh mls qos int g0/1 q GigabitEthernet0/1 Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 Dscp-threshold map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 01 01 01 01 01 01 01 01 01 01 1 : 01 01 01 01 01 01 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 01 01 01 01 01 01 01 01 4 : 01 01 01 01 01 01 01 01 01 01 5 : 01 01 01 01 01 01 01 01 01 01 6 : 01 01 01 01 Cos-queue map: cos-qid 0 - 2 1 - 1 2 - 2 3 - 3 4 - 2 5 - 2 6 - 2 7 - 2 S6(config-if)#wrr S6(config-if)#wrr-queue ba S6(config-if)#wrr-queue bandwidth 25 50 25 1 S6(config-if)#wrr S6(config-if)#wrr-queue th S6(config-if)#wrr-queue threshold ? <1-4> enter threshold queue id (1-4) S6(config-if)#wrr-queue threshold 1 ? <1-100> enter percent of queue size for threshold 1 S6(config-if)#wrr-queue threshold 1             ? bandwidth Configure WRR bandwidth cos-map Configure cos-map for a queue id dscp-map Configure dscp-map for a queue threshold queue-limit Configure queue-limit random-detect Configure random-detect threshold Configure queue tail-drop thresholds S6(config-if)#wrr-queue ds S6(config-if)#wrr-queue dscp-map ? <1-2> enter dscp-map threshold id (1-2) S6(config-if)#wrr-queue dscp-map 2 10 26 S6(config-if)#wrr-queue dscp-map 2 10 26bandwidth 25 50 25 1do sh mls qos int g0/1 q  GigabitEthernet0/1 Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 50 3 - 25 4 - 1 Dscp-threshold map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 01 01 01 01 01 01 01 01 01 01 1 : 02 01 01 01 01 01 01 01 01 01 2 : 01 01 01 01 01 01 02 01 01 01 3 : 01 01 01 01 01 01 01 01 01 01 4 : 01 01 01 01 01 01 01 01 01 01 5 : 01 01 01 01 01 01 01 01 01 01 6 : 01 01 01 01 Cos-queue map: cos-qid 0 - 2 1 - 1 2 - 2 3 - 3 4 - 2 5 - 2 6 - 2 7 - 2 S6(config-if)#wrr S6(config-if)#wrr-queue th S6(config-if)#wrr-queue threshold 1 ? <1-100> enter percent of queue size for threshold 1 S6(config-if)#wrr-queue threshold 1 40 100 S6(config-if)#wrr-queue threshold 1 40 100        3 60 100 S6(config-if)#^Z S6# 1d18h: %SYS-5-CONFIG_I: Configured from console by console S6#confi tt sh mls qos mapconfig t sh mls qos mapconfit  t sh mls qos int g 0/1 GigabitEthernet0/1 trust state: not trusted trust mode: not trusted COS override: dis default COS: 0 DSCP Mutation Map: Default DSCP Mutation Map Trust device: none S6#sh mls qos int g 0/1 q GigabitEthernet0/1 Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 50 3 - 25 4 - 1 Dscp-threshold map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 01 01 01 01 01 01 01 01 01 01 1 : 02 01 01 01 01 01 01 01 01 01 2 : 01 01 01 01 01 01 02 01 01 01 3 : 01 01 01 01 01 01 01 01 01 01 4 : 01 01 01 01 01 01 01 01 01 01 5 : 01 01 01 01 01 01 01 01 01 01 6 : 01 01 01 01 Cos-queue map: cos-qid 0 - 2 1 - 1 2 - 2 3 - 3 4 - 2 5 - 2 6 - 2 7 - 2 S6#sh run | b mls mls qos map dscp-cos 8 9 11 13 15 24 25 27 to 2 mls qos map dscp-cos 29 31 to 2 mls qos map ip-prec-dscp 0 14 16 28 32 40 48 56 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 no switchport ip address 20.10.2.1 255.255.255.0 --More--  ! interface FastEthernet0/2 no switchport ip address 20.10.1.2 255.255.255.0 ! interface FastEthernet0/3 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport access vlan 10 switchport mode dynamic desirable mls qos cos 5 mls qos trust dscp ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 switchport access vlan 10 switchport mode dynamic desirable --More--   mls qos trust ip-precedence ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable ! interface FastEthernet0/14 switchport mode dynamic desirable ! --More--  interface FastEthernet0/15 switchport mode dynamic desirable ! interface FastEthernet0/16 switchport mode dynamic desirable ! interface FastEthernet0/17 switchport mode dynamic desirable ! interface FastEthernet0/18 switchport mode dynamic desirable ! interface FastEthernet0/19 switchport mode dynamic desirable ! interface FastEthernet0/20 switchport mode dynamic desirable ! interface FastEthernet0/21 switchport mode dynamic desirable ! interface FastEthernet0/22 switchport mode dynamic desirable --More--  ! interface FastEthernet0/23 switchport mode dynamic desirable ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk ! interface GigabitEthernet0/1 switchport mode dynamic desirable wrr-queue bandwidth 25 50 25 1 wrr-queue threshold 1 40 100 wrr-queue threshold 3 60 100 wrr-queue cos-map 1 1 wrr-queue cos-map 2 0 2 4 5 6 7 wrr-queue cos-map 3 3 wrr-queue dscp-map 2 10 26 ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address --More--   S6#interface GigabitEthernet0/2 ^ % Invalid input detected at '^' marker. S6# wrr-queue bandwidth 25 50 25 1 ^ % Invalid input detected at '^' marker. S6# wrr-queue cos-map 1 1 ^ % Invalid input detected at '^' marker. S6# wrr-queue cos-map 2 0 2 4 5 6 7 ^ % Invalid input detected at '^' marker. S6# wrr-queue cos-map 3 3 ^ % Invalid input detected at '^' marker. S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#interface GigabitEthernet0/2 S6(config-if)# wrr-queue bandwidth 25 50 25 1 S6(config-if)# wrr-queue cos-map 1 1 S6(config-if)# wrr-queue cos-map 2 0 2 4 5 6 7 S6(config-if)# wrr-queue cos-map 3 3 S6(config-if)#wrr S6(config-if)#wrr-queue dsc S6(config-if)#wrr-queue dscp-map ? <1-2> enter dscp-map threshold id (1-2) S6(config-if)#wrr-queue dscp-map 2 ? <0-63> DSCP values separated by spaces (up to 8 values total) S6(config-if)#wrr-queue dscp-map 2 26 S6(config-if)#wrr S6(config-if)#wrr-queue ? bandwidth Configure WRR bandwidth cos-map Configure cos-map for a queue id dscp-map Configure dscp-map for a queue threshold queue-limit Configure queue-limit random-detect Configure random-detect threshold Configure queue tail-drop thresholds S6(config-if)#wrr-queue ra S6(config-if)#wrr-queue random-detect ? max-threshold max-thresholds S6(config-if)#wrr-queue random-detect m S6(config-if)#wrr-queue random-detect max-threshold ? <1-4> enter threshold queue id (1-4) S6(config-if)#wrr-queue random-detect max-threshold 3 ? <1-100> enter percent of queue size for threshold 1 S6(config-if)#wrr-queue random-detect max-threshold 3 40 ? <1-100> enter percent of queue size for threshold 2 S6(config-if)#wrr-queue random-detect max-threshold 3 40 80 S6(config-if)#^Z S6# 1d19h: %SYS-5-CONFIG_I: Configured from console by console S6#sh run int gi 0/2 Building configuration... Current configuration : 254 bytes ! interface GigabitEthernet0/2 switchport mode dynamic desirable wrr-queue bandwidth 25 50 25 1 wrr-queue random-detect max-threshold 3 40 80 wrr-queue cos-map 1 1 wrr-queue cos-map 2 0 2 4 5 6 7 wrr-queue cos-map 3 3 wrr-queue dscp-map 2 26 end S6# RACK99AS>7 [Resuming connection 7 to r7 ... ] R7#sh vlas    class Class Map match-all S5Other (id 2) Match access-group name S5 Class Map match-any class-default (id 0) Match any Class Map match-all S5Telnet (id 1) Match access-group name S5 Match protocol telnet Class Map match-any JPG (id 3) Match protocol http url "*.jpg" Match protocol http url "*.jpe" Match protocol http url "*.jpeg" Match protocol http mime "*jpeg" Match protocol http mime "*jpe" Match protocol http mime "*jpg" R7#  conf t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#ip nbar por R7(config)#ip nbar port-map ftp tcp 20 21 R7(config)#class ftp ^ % Invalid input detected at '^' marker. R7(config)#class ftp     R7(config)#class-map       >? % Unrecognized command R7(config)#class > ? % Unrecognized command R7(config)#class   R7(config)#class-map ftp R7(config-cmap)#match pro R7(config-cmap)#match protocol ftp R7(config-cmap)#exit R7(config)#class R7(config)#class-map telnet R7(config-cmap)#match pro telnet R7(config-cmap)#exit R7(config)#pol R7(config)#policy-map Prob20to22 R7(config-pmap)#class R7(config-pmap)#class ftp R7(config-pmap-c)#ban R7(config-pmap-c)#bandwidth per R7(config-pmap-c)#bandwidth percent 2 R7(config-pmap-c)#bandwidth percent 25 R7(config-pmap-c)#exit R7(config-pmap)#class R7(config-pmap)#class telnet R7(config-pmap-c)#class telnetexit bandwidth percent 25 R7(config-pmap-c)#exit R7(config-pmap)#class R7(config-pmap)#class class-deau  fault R7(config-pmap-c)#n ba R7(config-pmap-c)#bandwidth p R7(config-pmap-c)#bandwidth percent 50 R7(config-pmap-c)#int f 0/1 R7(config-if)#int f 0/1 0 R7(config-if)#ser R7(config-if)#service-policy out Prob20to22 I/f FastEthernet0/0 class class-default requested bandwidth 50%, available only 25% R7(config-if)#max R7(config-if)#max-reserved-bandwidth 100 R7(config-if)#max-reserved-bandwidth 100service-policy out Prob20to22 R7(config-if)#^Z R7# *Mar 2 15:05:41.000: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b class class-map match-all telnet match protocol telnet class-map match-all S5Other match access-group name S5 class-map match-all S5Telnet match access-group name S5 match protocol telnet class-map match-any JPG match protocol http url "*.jpg" match protocol http url "*.jpe" match protocol http url "*.jpeg" match protocol http mime "*jpeg" match protocol http mime "*jpe" match protocol http mime "*jpg" class-map match-all ftp match protocol ftp ! ! policy-map Prob5 class JPG shape average 1000000 class S5Telnet bandwidth 1000 --More--   class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 class class-default policy-map Prob20to22 class ftp bandwidth percent 25 class telnet bandwidth percent 25 class class-default bandwidth percent 50 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex max-reserved-bandwidth 100 service-policy output Prob20to22 --More--  ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 ip helper-address 180.40.7.66 speed auto half-duplex vrrp 47 ip 180.40.7.133 glbp 47 ip 180.40.7.134 glbp 47 weighting track 1 decrement 100 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 ! interface Serial1/0 no ip address encapsulation frame-relay frame-relay interface-queue priority ! interface Serial1/0.1 point-to-point --More--   R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#i p  p access-list ex Prob21and22 R7(config-ext-nacl)#per ip host 87.23.11.123 any R7(config-ext-nacl)#per ip host 87.23.11.123 any   ahost 87.23.11.123 nhost 87.23.11.123 yhost 87.23.11.123  host 87.23.11.123  R7(config-ext-nacl)#exity ^ % Invalid input detected at '^' marker. R7(config-ext-nacl)#exity ^ % Invalid input detected at '^' marker. R7(config-ext-nacl)#exity  R7(config)#class R7(config)#class-map sql R7(config-cmap)#match pro R7(config-cmap)#match protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 --More--   custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching (Direct encapsulation only) dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) --More--   ipsec IP Security Protocol (ESP/AH) ipv6 IPV6 ipx Novell IPX irc Internet Relay Chat kazaa2 Kazaa Version 2 kerberos Kerberos l2tp L2F/L2TP tunnel ldap Lightweight Directory Access Protocol llc2 llc2 napster Napster Traffic netbios NetBIOS netshow Microsoft Netshow nfs Network File System nntp Network News Transfer Protocol notes Lotus Notes(R) novadigm Novadigm EDM ntp Network Time Protocol pad PAD links pcanywhere Symantec pcANYWHERE pop3 Post Office Protocol pppoe PPP over Ethernet pptp Point-to-Point Tunneling Protocol printer print spooler/lpd --More--   qllc qllc protocol rcmd BSD r-commands (rsh, rlogin, rexec) rip Routing Information Protocol rsrb Remote Source-Route Bridging rsvp Resource Reservation Protocol rtp Real Time Protocol rtspplayer RTSP players streaming protocol secure-ftp FTP over TLS/SSL secure-http Secured HTTP secure-imap Internet Message Access Protocol over TLS/SSL secure-irc Internet Relay Chat over TLS/SSL secure-ldap Lightweight Directory Access Protocol over TLS/SSL secure-nntp Network News Transfer Protocol over TLS/SSL secure-pop3 Post Office Protocol over TLS/SSL secure-telnet Telnet over TLS/SSL smtp Simple Mail Transfer Protocol snapshot Snapshot routing support snmp Simple Network Management Protocol socks SOCKS sqlnet SQL*NET for Oracle sqlserver MS SQL Server ssh Secured Shell streamwork Xing Technology StreamWorks player --More--   stun Serial Tunnel --More--   sunrpc Sun RPC --More--   syslog System Logging Utility --More--   telnet Telnet --More--   R7(config-cmap)#match protocol sql R7(config-cmap)#match protocol sqln R7(config-cmap)#match protocol sqlnet R7(config-cmap)#match protocol sqlnet     se R7(config-cmap)#exit R7(config)#exitmatch protocol sqlsenet se net class-map sql msqlasqltsqlcsqlhsql-sqlasqlnsqlysql R7(config-cmap)#exit R7(config)#exitclass-map match-anysqlnclass-map match-anysqloclass-map match-anysql class-map match-anysql R7(config)#no class-map match-anysqlexit class-map match-anysql sql R7(config-cmap)#do sh run | b class class-map match-all telnet match protocol telnet class-map match-all S5Other match access-group name S5 class-map match-all S5Telnet match access-group name S5 match protocol telnet class-map match-any JPG match protocol http url "*.jpg" match protocol http url "*.jpe" match protocol http url "*.jpeg" match protocol http mime "*jpeg" match protocol http mime "*jpe" match protocol http mime "*jpg" class-map match-all ftp match protocol ftp class-map match-any sql match protocol sqlnet match protocol sqlserver ! ! policy-map Prob5 class JPG --More--   R7(config-cmap)#exit R7(config)#class R7(config)#class-map Prob    Sq Ql   Prob21and22 R7(config-cmap)#match acc R7(config-cmap)#match access-group ? <1-2699> Access list index name Named Access List R7(config-cmap)#match access-group Prob22 1and22 ^ % Invalid input detected at '^' marker. R7(config-cmap)#match access-group Prob21and22 match access-group Prob21and22nProb21and22aProb21and22mProb21and22eProb21and22 Prob21and22 R7(config-cmap)#match ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R7(config-cmap)#match class-map SQL   sql R7(config-cmap)#exit R7(config)#pol R7(config)#policy-map Prob20to22 R7(config-pmap)#clas R7(config-pmap)#class sql R7(config-pmap-c)#class sql         exit R7(config-pmap)#no class sql R7(config-pmap)#class Prob21and22 R7(config-pmap-c)#pri R7(config-pmap-c)#priority ? <8-2000000> Kilo Bits per second percent % of total bandwidth R7(config-pmap-c)#priority 56 ? <32-2000000> Burst in bytes R7(config-pmap-c)#priority 56 128 I/f FastEthernet0/0 class Prob21and22 requested bandwidth 56 (kbps), available only 0 (kbps) R7(config-pmap-c)#interface FastEthernet0/0 R7(config-if)# R7(config-if)#no service-policy output Prob20to22 R7(config-if)#! R7(config-if)#no policy-map Prob20to22 R7(config)# R7(config)#policy-map Prob20to22 R7(config-pmap)# class Prob21and22 R7(config-pmap-c)# priority 56 128 R7(config-pmap-c)# R7(config-pmap-c)# class ftp R7(config-pmap-c)# bandwidth rem percent 25 R7(config-pmap-c)# class telnet R7(config-pmap-c)# bandwidth rem percent 25 R7(config-pmap-c)# class class-default R7(config-pmap-c)# bandwidth rem percent 50 R7(config-pmap-c)#! R7(config-pmap-c)#interface FastEthernet0/0 R7(config-if)# R7(config-if)#service-policy output Prob20to22 R7(config-if)#! R7(config-if)#^Z R7#sh po *Mar 2 15:14:01.312: %SYS-5-CONFIG_I: Configured from console by console R7#sh pol int fa 0/0 FastEthernet0/0 Service-policy output: Prob20to22 Class-map: Prob21and22 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group name Prob21and22 Match: class-map match-any sql Match: protocol sqlnet 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol sqlserver 0 packets, 0 bytes 5 minute rate 0 bps Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: ftp (match-all) --More--   0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 2 packets, 154 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any --More--   Queueing Output Queue: Conversation 267 Bandwidth remaining 50 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 R7#sh run | b clas class-map match-all telnet match protocol telnet class-map match-all S5Other match access-group name S5 class-map match-all S5Telnet match access-group name S5 match protocol telnet class-map match-any sql match protocol sqlnet match protocol sqlserver class-map match-all Prob21and22 match access-group name Prob21and22 match class-map sql class-map match-any JPG match protocol http url "*.jpg" match protocol http url "*.jpe" match protocol http url "*.jpeg" match protocol http mime "*jpeg" match protocol http mime "*jpe" match protocol http mime "*jpg" class-map match-all ftp match protocol ftp ! --More--  ! policy-map Prob5 class JPG shape average 1000000 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 class class-default policy-map Prob20to22 class Prob21and22 priority 56 128 class ftp bandwidth remaining percent 25 class telnet bandwidth remaining percent 25 class class-default bandwidth remaining percent 50 ! ! ! ! --More--  ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex max-reserved-bandwidth 100 service-policy output Prob20to22 ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 ip helper-address 180.40.7.66 speed auto half-duplex vrrp 47 ip 180.40.7.133 glbp 47 ip 180.40.7.134 glbp 47 weighting track 1 decrement 100 standby 47 ip 180.40.7.132 standby 47 preempt --More--   service-policy output Prob5 ! interface Serial1/0 no ip address encapsulation frame-relay frame-relay interface-queue priority ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address shutdown --More--  ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address --More--   shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server ! ip access-list standard S5 permit 208.28.1.2 ! ip access-list extended Prob21and22 permit ip host 87.23.11.123 any permit ip any host 87.23.11.123 ! ! map-class frame-relay Prob6 frame-relay priority-group 1 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www --More--   R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#pol Prob20to22 R7(config-pmap)#class R7(config-pmap)#class class-default R7(config-pmap-c)#fai R7(config-pmap-c)#fair-queue ? <16-4096> Number Dynamic Conversation Queues R7(config-pmap-c)#fair-queue deconfigure bandwidth before issuing this command in this class R7(config-pmap-c)#ban R7(config-pmap-c)#bandwidth Q           no ban R7(config-pmap-c)#no bandwidth rem per 50 R7(config-pmap-c)#no bandwidth rem per 50fair-queue  R7(config-pmap-c)#do sh pol int fa 0/0 FastEthernet0/0 Service-policy output: Prob20to22 Class-map: Prob21and22 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group name Prob21and22 Match: class-map match-any sql Match: protocol sqlnet 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol sqlserver 0 packets, 0 bytes 5 minute rate 0 bps Queueing Strict Priority Output Queue: Conversation 264 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: ftp (match-all) --More--   0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 265 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 266 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 53 packets, 5070 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any --More--   Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 256 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-pmap-c)#do sh pol int fa 0/0fair-queue do sh pol int fa 0/0 do sh pol int fa 0/0 do sh pol int fa 0/0fair-queue 512 R7(config-pmap-c)#fair-queue 512do sh pol int fa 0/0 FastEthernet0/0 Service-policy output: Prob20to22 Class-map: Prob21and22 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group name Prob21and22 Match: class-map match-any sql Match: protocol sqlnet 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol sqlserver 0 packets, 0 bytes 5 minute rate 0 bps Queueing Strict Priority Output Queue: Conversation 520 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: ftp (match-all) --More--   0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 521 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 522 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 56 packets, 5607 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any --More--   Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 512 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-pmap-c)# ^Z R7#sh *Mar 2 15:18:17.404: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | polbpol pol policy-map Prob5 class JPG shape average 1000000 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 class class-default policy-map Prob20to22 class Prob21and22 priority 56 128 class ftp bandwidth remaining percent 25 class telnet bandwidth remaining percent 25 class class-default fair-queue 512 ! ! ! ! ! --More--   R7#shg    pi p;  ol int f 0/0 FastEthernet0/0 Service-policy output: Prob20to22 Class-map: Prob21and22 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group name Prob21and22 Match: class-map match-any sql Match: protocol sqlnet 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol sqlserver 0 packets, 0 bytes 5 minute rate 0 bps Queueing Strict Priority Output Queue: Conversation 520 Bandwidth 56 (kbps) Burst 128 (Bytes) (pkts matched/bytes matched) 0/0 (total drops/bytes drops) 0/0 Class-map: ftp (match-all) --More--   0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 521 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 522 Bandwidth remaining 25 (%) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 71 packets, 7068 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any --More--   Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 512 (total queued/total drops/no-buffer drops) 0/0/0 R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#pol p Prob23and24 R7(config-pmap)#clas R7(config-pmap)#class ftp R7(config-pmap-c)#pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 256000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 256000 R7(config-pmap-c-police)#do sh pol Policy Map Prob5 Class JPG Traffic Shaping Average Rate Traffic Shaping CIR 1000000 (bps) Max. Buffers Limit 1000 (Packets) Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class S5Other police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 Class class-default Policy Map Prob20to22 Class Prob21and22 Strict Priority Bandwidth 56 (kbps) Burst 128 (Bytes) Class ftp Bandwidth remaining 25 (%) Max Threshold 64 (packets) Class telnet Bandwidth remaining 25 (%) Max Threshold 64 (packets) Class class-default Flow based Fair Queueing --More--   Bandwidth 0 (kbps) Max Threshold 64 (packets) Policy Map Prob23and24 Class ftp police cir 256000 bc 8000 conform-action transmit exceed-action drop R7(config-pmap-c-police)#exit R7(config-pmap-c)#exo it R7(config-pmap)#c;las     class R7(config-pmap)#class telnet R7(config-pmap-c)#pol R7(config-pmap-c)#police 56000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 1400 ? <1000-512000000> Burst bytes be Excess burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 56000 1400 3500 ? conform-action action when rate is less than conform burst R7(config-pmap-c)#police 56000 1400 3500 con R7(config-pmap-c)#police 56000 1400 3500 conform-action set R7(config-pmap-c)#police 56000 1400 3500 conform-action set-p R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit ? <0-7> new precedence R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit                                                         exi R7(config-pmap)#exi R7(config)#class R7(config)#class-map test R7(config-cmap)#match ip pr R7(config-cmap)#match ip precedence ? <0-7> Enter up to 4 precedence values separated by white-spaces critical Match packets with critical precedence (5) flash Match packets with flash precedence (3) flash-override Match packets with flash override precedence (4) immediate Match packets with immediate precedence (2) internet Match packets with internetwork control precedence (6) network Match packets with network control precedence (7) priority Match packets with priority precedence (1) routine Match packets with routine precedence (0) R7(config-cmap)#match ip precedence                     exit R7(config)#no clas R7(config)#no class-map test                 do sh class Class Map match-all telnet (id 5) Match protocol telnet Class Map match-all test (id 8) Match none Class Map match-all S5Other (id 2) Match access-group name S5 Class Map match-any class-default (id 0) Match any Class Map match-all S5Telnet (id 1) Match access-group name S5 Match protocol telnet Class Map match-all Prob21and22 (id 7) Match access-group name Prob21and22 Match class-map sql Class Map match-any JPG (id 3) Match protocol http url "*.jpg" Match protocol http url "*.jpe" --More--   R7(config)#no class test ^ % Invalid input detected at '^' marker. R7(config)#no class test      R7(config)#no class-map test R7(config)#no class-map test test do sh class exit class-map testexi class telnetexit do sh polpolice 256000 class ftp pol Prob23and24 R7(config-pmap)#class telnet R7(config-pmap-c)#pol R7(config-pmap-c)#police 56000 1400 355 00 se   c  c R7(config-pmap-c)#police 56000 1400 3500 conform-action set R7(config-pmap-c)#police 56000 1400 3500 conform-action set-p R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 e$0 1400 3500 conform-action set-prec-transmit 1 ec  R7(config-pmap-c)#$0 1400 3500 conform-action set-prec-transmit 1 ec  R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action se R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action set-p R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 R7(config-pmap-c-police)#do sh pol Policy Map Prob5 Class JPG Traffic Shaping Average Rate Traffic Shaping CIR 1000000 (bps) Max. Buffers Limit 1000 (Packets) Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class S5Other police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 Class class-default Policy Map Prob20to22 Class Prob21and22 Strict Priority Bandwidth 56 (kbps) Burst 128 (Bytes) Class ftp Bandwidth remaining 25 (%) Max Threshold 64 (packets) Class telnet Bandwidth remaining 25 (%) Max Threshold 64 (packets) Class class-default Flow based Fair Queueing --More--   Bandwidth 0 (kbps) Max Threshold 64 (packets) Policy Map Prob23and24 Class ftp police cir 256000 bc 8000 conform-action transmit exceed-action drop Class telnet police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 R7(config-pmap-c-police)#do sh pol v R7(config-pmap-c-police)#violate-action dr R7(config-pmap-c-police)#violate-action drop R7(config-pmap-c-police)#violate-action drop do sh pol $-prec-transmit 1 exceed-action set-prec-transmit 0 do sh pol  Policy Map Prob5 Class JPG Traffic Shaping Average Rate Traffic Shaping CIR 1000000 (bps) Max. Buffers Limit 1000 (Packets) Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class S5Other police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 Class class-default Policy Map Prob20to22 Class Prob21and22 Strict Priority Bandwidth 56 (kbps) Burst 128 (Bytes) Class ftp Bandwidth remaining 25 (%) Max Threshold 64 (packets) Class telnet Bandwidth remaining 25 (%) Max Threshold 64 (packets) Class class-default Flow based Fair Queueing --More--   Bandwidth 0 (kbps) Max Threshold 64 (packets) Policy Map Prob23and24 Class ftp police cir 256000 bc 8000 conform-action transmit exceed-action drop Class telnet police cir 56000 bc 1400 be 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop R7(config-pmap-c-police)# exi R7(config-pmap-c)#exi R7(config-pmap)#v class class-default R7(config-pmap-c)#fa R7(config-pmap-c)#fair-queue R7(config-pmap-c)#qu R7(config-pmap-c)#queue-limit ? <1-4096> Packets R7(config-pmap-c)#queue-limit 100 R7(config-pmap-c)#int s 1/0.1 R7(config-subif)#ser R7(config-subif)#service-policy out Prob23and24 CBWFQ : Not supported on subinterfaces R7(config-subif)#exit R7(config)#map R7(config)#map-cl R7(config)#map-class f R7(config)#map-class frame-relay Prob23and24 R7(config-map-class)#ser R7(config-map-class)#service-policy out Prob23and24 R7(config-map-class)#int s 1/0.1 R7(config-subif)#fram R7(config-subif)#frame-relay class R7(config-subif)#frame-relay class Prob23and24 R7(config-subif)#sh po, int fa    s , int l int  int s1/0.1 ^ % Invalid input detected at '^' marker. R7(config-subif)#sh pol int s1/0.1dsh pol int s1/0.1osh pol int s1/0.1ish pol int s1/0.1 sh pol int s1/0.1sh pol int s1/0.1 sh pol int s1/0.1  sh pol int s1/0.1 R7(config-subif)#int s 1/0 R7(config-if)#fram R7(config-if)#frame-relay traff R7(config-if)#frame-relay traffic-shaping R7(config-if)#frame-relay traffic-shaping int s 1/0 do sh pol int s1/0.1 Serial1/0.1: DLCI 703 - Service-policy output: Prob23and24 Class-map: ftp (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp police: cir 256000 bps, bc 8000 bytes conformed 0 packets, 0 bytes; actions: transmit exceeded 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps Class-map: telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet police: cir 56000 bps, bc 1400 bytes, be 3500 bytes conformed 0 packets, 0 bytes; actions: --More--   set-prec-transmit 1 exceeded 0 packets, 0 bytes; actions: set-prec-transmit 0 violated 0 packets, 0 bytes; actions: drop conformed 0 bps, exceed 0 bps, violate 0 bps Class-map: class-default (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 16 (total queued/total drops/no-buffer drops) 0/0/0 R7(config-if)#do sh fram      traff Interface Se1/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 701 56000 875 7000 0 125 875 - Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 703 56000 875 7000 0 125 875 - Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 702 56000 875 7000 0 125 875 - R7(config-if)#exit R7(config)#pol Prob23and24 R7(config-pmap)#class class-default R7(config-pmap-c)#pol R7(config-pmap-c)#police 256000      512000 R7(config-pmap-c-police)#exit R7(config-pmap-c)#exi R7(config-pmap)# R7(config-pmap)#exit R7(config)#map R7(config)#map-cl R7(config)#map-class f R7(config)#map-class frame-relay Prob23and24 R7(config-map-class)#c fra R7(config-map-class)#frame-relay cir 600000 R7(config-map-class)#^Z R7#sh *Mar 2 15:34:07.954: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | po  b pol policy-map Prob5 class JPG shape average 1000000 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 class class-default policy-map Prob20to22 class Prob21and22 priority 56 128 class ftp bandwidth remaining percent 25 class telnet bandwidth remaining percent 25 class class-default fair-queue 512 policy-map Prob23and24 class ftp police 256000 class telnet police cir 56000 bc 1400 be 3500 --More--   conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0 violate-action drop class class-default fair-queue queue-limit 100 police 512000 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex max-reserved-bandwidth 100 service-policy output Prob20to22 ! interface BRI0/0 no ip address shutdown --More--  ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 ip helper-address 180.40.7.66 speed auto half-duplex vrrp 47 ip 180.40.7.133 glbp 47 ip 180.40.7.134 glbp 47 weighting track 1 decrement 100 standby 47 ip 180.40.7.132 standby 47 preempt service-policy output Prob5 ! interface Serial1/0 no ip address encapsulation frame-relay frame-relay traffic-shaping frame-relay interface-queue priority ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network broadcast ip ospf priority 0 --More--   frame-relay class Prob23and24 frame-relay interface-dlci 703 frame-relay ip tcp header-compression passive ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 --More--   no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server --More--  ! ip access-list standard S5 permit 208.28.1.2 ! ip access-list extended Prob21and22 permit ip host 87.23.11.123 any permit ip any host 87.23.11.123 ! ! map-class frame-relay Prob6 frame-relay priority-group 1 ! map-class frame-relay Prob23and24 frame-relay cir 600000 service-policy output Prob23and24 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www ! ! ! ! ! ! --More--   R7# RACK99AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run int s 1/0.2 Building configuration... Current configuration : 162 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob3 end R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#map-cl R2(config)#map-class fr R2(config)#map-class frame-relay Prob25and26 R2(config-map-class)#fra R2(config-map-class)#frame-relay cir 64000 R2(config-map-class)#fra R2(config-map-class)#frame-relay ad R2(config-map-class)#frame-relay adaptive-shaping b R2(config-map-class)#frame-relay adaptive-shaping becn R2(config-map-class)#fr R2(config-map-class)#frame-relay ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 7000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R2(config-map-class)#frame-relay mi R2(config-map-class)#frame-relay mincir 32000 R2(config-map-class)#do sh run | b map-class map-class frame-relay Prob3 frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn ! map-class frame-relay Prob25and26 frame-relay cir 64000 frame-relay mincir 32000 frame-relay adaptive-shaping becn access-list 100 deny ospf any any access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 --More--   R2(config-map-class)#do sh run map Building configuration... Current configuration: ! map-class frame-relay Prob3 frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn ! map-class frame-relay Prob25and26 frame-relay cir 64000 frame-relay mincir 32000 frame-relay adaptive-shaping becn end R2(config-map-class)#int s 1/0.1 R2(config-subif)#fram class Pro25and26 %Creating new map-class. R2(config-subif)#fram class Pro25and26b25and26 R2(config-subif)#do sh map   run map Building configuration... Current configuration: ! map-class frame-relay Prob3 frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn ! map-class frame-relay Prob25and26 frame-relay cir 64000 frame-relay mincir 32000 frame-relay adaptive-shaping becn ! map-class frame-relay Pro25and26 end R2(config-subif)#exit R2(config)#no map-class frame-relay Pro25and26 R2(config)#^Z R2#sh *Mar 2 19:43:14.804: %SYS-5-CONFIG_I: Configured from console by console R2#sh traff Interface Se1/0 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 201 56000 875 7000 0 125 875 - Interface Se1/0.1 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 203 64000 1000 64000 0 125 1000 BECN Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active 207 64000 5000 64000 32000 125 1000 BECN R2#sh run int s 1/0 Building configuration... Current configuration : 113 bytes ! interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping end R2#sh run int s 1/0traff confi t sh traffrun int s 1/0 sh run | b 1/0 interface Serial1/0 no ip address encapsulation frame-relay no fair-queue frame-relay traffic-shaping ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network broadcast ip ospf priority 0 frame-relay class Prob25and26 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 frame-relay de-group 1 207 frame-relay interface-dlci 207 class Prob3 ! interface Serial1/1 no ip address shutdown ! --More--  interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown --More--  ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! ip http server no ip http secure-server ! ! map-class frame-relay Prob3 frame-relay cir 64000 frame-relay bc 64000 frame-relay be 32000 frame-relay adaptive-shaping becn ! map-class frame-relay Prob25and26 frame-relay cir 64000 frame-relay mincir 32000 frame-relay adaptive-shaping becn access-list 100 deny ospf any any access-list 100 permit ip any any --More--  ! --More--  ! --More--  ! --More--  ! --More--