=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.02.09 17:56:13 =~=~=~=~=~=~=~=~=~=~=~= R7# R7# R7# R7# R7# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv R1(config)#ipv6 u R1(config)#ipv6 unicast-routing R1(config)#int e 0/1 R1(config-if)#ipv add R1(config-if)#ipv address 2005:0:104::/64 eu R1(config-if)#ipv address 2005:0:104::/64 eui-64 R1(config-if)#int s 0/1 R1(config-if)#int s 0/1pv address 2005:0:104::/64 eui-64 ::/64 eui-64 2::/64 eui-64  R1(config-if)#do sh ipv int brie Ethernet0/0 [up/up] unassigned Serial0/0 [administratively down/down] unassigned Ethernet0/1 [up/up] FE80::20A:8AFF:FEF0:D981 2005:0:104:0:20A:8AFF:FEF0:D981 Serial0/1 [up/up] FE80::20A:8AFF:FEF0:D980 2005:0:102:0:20A:8AFF:FEF0:D980 R1(config-if)# R1# *Mar 1 06:50:45.468: %SYS-5-CONFIG_I: Configured from console by console R1# R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipv un R2(config)#ipv unicast-routing R2(config)#int s 1/1 R2(config-if)#ipv add 2005:0:102::/65 4 eu R2(config-if)#ipv add 2005:0:102::/64 eui-64 R2(config-if)#int s 1/2 R2(config-if)#int s 1/2pv add 2005:0:102::/64 eui-64 ::/64 eui-64 ::/64 eui-64 2::/64 eui-64 0::/64 eui-64 3::/64 eui-64  R2(config-if)#ipv add 2005:0:1203::/64 eui-64 nt s 1/2  0.1 R2(config-subif)#int s 1/0.1pv add 2005:0:1203::/64 eui-64 203::/64 eui-64 203::/64 eui-64 ::/64 eui-64 3::/64 eui-64 7::/64 eui-64  R2(config-subif)#ipv add 2005:0:237::/64 eui-64 nt s 1/0.1  2 R2(config-subif)#int s 1/0.2pv add 2005:0:237::/64 eui-64 ::/64 eui-64 ::/64 eui-64 ::/64 eui-64 7::/64 eui-64 0::/64 eui-64 2::/64 eui-64  R2(config-subif)#do sh ipv int brie FastEthernet0/0 [administratively down/down] unassigned BRI0/0 [administratively down/down] unassigned BRI0/0:1 [administratively down/down] unassigned BRI0/0:2 [administratively down/down] unassigned FastEthernet0/1 [administratively down/down] unassigned Serial1/0 [up/up] unassigned Serial1/0.1 [up/up] FE80::213:60FF:FEF0:FD40 2005:0:237:0:213:60FF:FEF0:FD40 Serial1/0.2 [up/up] FE80::213:60FF:FEF0:FD40 2005:0:702:0:213:60FF:FEF0:FD40 Serial1/1 [up/up] FE80::213:60FF:FEF0:FD40 2005:0:102:0:213:60FF:FEF0:FD40 Serial1/2 [up/up] FE80::213:60FF:FEF0:FD40 --More--   2005:0:1203:0:213:60FF:FEF0:FD40 Serial1/3 [administratively down/down] unassigned Serial1/4 [administratively down/down] unassigned Serial1/5 [administratively down/down] unassigned Serial1/6 [administratively down/down] unassigned Serial1/7 [administratively down/down] unassigned R2(config-subif)# R2# *Mar 1 06:51:23.370: %SYS-5-CONFIG_I: Configured from console by console R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] * R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ipv un R3(config)#ipv unicast-routing R3(config)#int s 1/2 R3(config-if)#ipv add 21  2005:0:1203::/64 en  R3(config-if)#int s 1/0 R3(config-if)#int s 1/0pv add 2005:0:1203::/64 e3::/64 e ::/64 e ::/64 e ::/64 e 2::/64 e3::/64 e7::/64 e R3(config-if)#int lo 0 R3(config-if)#ipv add 2000:3:3::/64 e R3(config-if)#do sh ipb v int brie FastEthernet0/0 [administratively down/down] unassigned BRI0/0 [administratively down/down] unassigned BRI0/0:1 [administratively down/down] unassigned BRI0/0:2 [administratively down/down] unassigned FastEthernet0/1 [up/up] unassigned Serial1/0 [up/up] FE80::213:7FFF:FE12:A4E0 2005:0:237:0:213:7FFF:FE12:A4E0 Serial1/1 [administratively down/down] unassigned Serial1/2 [up/up] FE80::213:7FFF:FE12:A4E0 2005:0:1203:0:213:7FFF:FE12:A4E0 Serial1/3 [administratively down/down] unassigned Serial1/4 [administratively down/down] unassigned Serial1/5 [administratively down/down] --More--   unassigned Serial1/6 [administratively down/down] unassigned Serial1/7 [administratively down/down] unassigned Loopback0 [up/up] FE80::213:7FFF:FE12:A4E0 2000:3:3:0:213:7FFF:FE12:A4E0 R3(config-if)# R3# *Mar 1 06:52:51.250: %SYS-5-CONFIG_I: Configured from console by console R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] *M R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ipb v u R4(config)#int fa 0/0 R4(config-if)#ipv add 2005:0:104::/64 e R4(config-if)#int lo 0 R4(config-if)#ipv add 2000:4:4::/64 e R4(config-if)#do sh ipv int brie FastEthernet0/0 [up/up] FE80::2D0:BAFF:FED3:BA40 2005:0:104:0:2D0:BAFF:FED3:BA40 ATM1/0 [up/up] unassigned Loopback0 [up/up] FE80::2D0:BAFF:FED3:BA40 2000:4:4:0:2D0:BAFF:FED3:BA40 R4(config-if)# R4# *Mar 1 06:56:33.202: %SYS-5-CONFIG_I: Configured from console by console R4# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv u R7(config)#int s 1/0.1 R7(config-subif)#ipv 2005:0:237::/64 e ^ % Invalid input detected at '^' marker. R7(config-subif)#ipv 2005:0:237::/64 ea2005:0:237::/64 ed2005:0:237::/64 ed2005:0:237::/64 e 2005:0:237::/64 e R7(config-subif)#int s 1/0.2 R7(config-subif)#int s 1/0.2pv add 2005:0:237::/64 e::/64 e ::/64 e ::/64 e 7::/64 e0::/64 e2::/64 e R7(config-subif)#do sh ipv int brie FastEthernet0/0 [administratively down/down] unassigned BRI0/0 [administratively down/down] unassigned BRI0/0:1 [administratively down/down] unassigned BRI0/0:2 [administratively down/down] unassigned FastEthernet0/1 [up/up] unassigned Serial1/0 [up/up] unassigned Serial1/0.1 [up/up] FE80::212:43FF:FEAC:6F60 2005:0:237:0:212:43FF:FEAC:6F60 Serial1/0.2 [up/up] FE80::212:43FF:FEAC:6F60 2005:0:702:0:212:43FF:FEAC:6F60 Serial1/1 [administratively down/down] unassigned Serial1/2 [administratively down/down] unassigned Serial1/3 [administratively down/down] --More--   R7(config-subif)# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#p 2005:0:104:0:20A:8AFF:FEF0:D981 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104:0:20A:8AFF:FEF0:D981, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#p 2005:0:102:0:213:60FF:FEF0:FD40 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102:0:213:60FF:FEF0:FD40, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/33 ms R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#p 2005:0:1203:0:213:7FFF:FE12:A4E0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203:0:213:7FFF:FE12:A4E0, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms R2#p 2005:0:237:0:213:7FFF:FE12:A4E0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237:0:213:7FFF:FE12:A4E0, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R2#p 2005:0:702:0:212:43FF:FEAC:6F60 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702:0:212:43FF:FEAC:6F60, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#do sh run int s 1/0 Building configuration... Current configuration : 106 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::/64 eui-64 end R3(config)#int s 1/0 R3(config-if)#fram map ipv 2005:0:237:0:213:60FF:FEF0:FD40 302 br R3(config-if)#fram map ipv 2005:0:237:0:212:43FF:FEAC:6F60 307 br R3(config-if)#^Z R3#pin *Mar 1 06:57:39.582: %SYS-5-CONFIG_I: Configured from console by console R3#pin 2005:0:237:0:212:43FF:FEAC:6F60 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237:0:212:43FF:FEAC:6F60, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/61 ms R3#pin 2005:0:237:0:212:43FF:FEAC:6F60                               2005:0:237:0:213:60FF:FEF0:FD40 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237:0:213:60FF:FEF0:FD40, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Ethernet0/0 ip address 180.40.7.66 255.255.255.224 half-duplex ! interface Serial0/0 no ip address shutdown --More--  ! interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::/64 eui-64 ! interface Serial0/1 no ip address ipv6 address 2005:0:102::/64 eui-64 clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! no ip http server ip classless ! ! ! ! ! --More--  ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address --More--   shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::/64 eui-64 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point --More--   ipv6 address 2005:0:702::/64 eui-64 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::/64 eui-64 ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::/64 eui-64 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip  eru   run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 no ip address --More--   ipv6 address 2000:3:3::/64 eui-64 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::/64 eui-64 frame-relay map ipv6 2005:0:237:0:212:43FF:FEAC:6F60 307 broadcast frame-relay map ipv6 2005:0:237:0:213:60FF:FEF0:FD40 302 broadcast --More--  ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::/64 eui-64 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address --More--   R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 no ip address ipv6 address 2000:4:4::/64 eui-64 ! interface FastEthernet0/0 --More--   no ip address duplex auto speed auto ipv6 address 2005:0:104::/64 eui-64 ! interface ATM1/0 ip address 192.10.32.13 255.255.255.0 no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 broadcast ! ! no ip http server no ip http secure-server ip classless ! ! ! ! ! ! ! ! --More--   R4# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7(config-subif)#^Z R7#sh run | *Mar 1 06:59:57.829: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address --More--   shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.1 255.255.255.224 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::/64 eui-64 frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::/64 eui-64 --More--   frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 --More--   R7# R7# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo 0 R4(config-if)#ipv ? IPv6 interface subcommands: address Configure IPv6 address on interface cef Cisco Express Forwarding for IPv6 enable Enable IPv6 on interface mtu Set IPv6 Maximum Transmission Unit nd IPv6 interface Neighbor Discovery subcommands redirects Enable sending of ICMP Redirect messages rip Configure RIP routing protocol traffic-filter Access control list for packets unnumbered Preferred interface for source address selection verify Enable per packet validation R4(config-if)#ipv rip ? WORD User selected string identifying this RIP process R4(config-if)#ipv rip R4Rip ? default-information Configure handling of default route enable Enable/disable RIP routing metric-offset Adjust default metric increment summary-address Configure address summarization R4(config-if)#ipv rip R4Rip en R4(config-if)#int fa 0/0 R4(config-if)#int fa 0/0pv rip R4Rip en R4(config-if)#^Z R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ipv rip R1Rip en R1(config-if)#int s 0.  0/1 R1(config-if)#int s 0/1pv rip R1Rip en R1(config-if)#^Z R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/1 R2(config-if)#ipv rip R2Rip en R2(config-if)#^Z R2#sh i *Mar 1 07:02:23.071: %SYS-5-CONFIG_I: Configured from console by console R2#sh ipv route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   via ::, Serial1/2 L 2005:0:1203:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#ping 2000:4:4:0:2D0:BAFF:FED3:BA40 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/32 ms R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] * R1#sh ru  n | b interface Ethernet  1 0/1 interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::/64 eui-64 ipv6 rip R1Rip enable ! interface Serial0/1 no ip address ipv6 address 2005:0:102::/64 eui-64 ipv6 rip R1Rip enable clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! no ip http server ip classless ! ! ipv6 router rip R1Rip ! --More--   R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b interface Serial1/1 interface Serial1/1 no ip address ipv6 address 2005:0:102::/64 eui-64 ipv6 rip R2Rip enable ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::/64 eui-64 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 --More--   no ip address shutdown ! interface Serial1/7 no ip address shutdown ! ip classless ! no ip http server no ip http secure-server ! ipv6 router rip R2Rip ! ! ! ! ! ! ! ! ! ! --More--   R2# RACK13AS>4 [Resuming connection 4 to r4 ... ] *M R4#sh run | b int interface Loopback0 no ip address ipv6 address 2000:4:4::/64 eui-64 ipv6 rip R4Rip enable ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2005:0:104::/64 eui-64 ipv6 rip R4Rip enable ! interface ATM1/0 ip address 192.10.32.13 255.255.255.0 no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 broadcast ! ! no ip http server no ip http secure-server ip classless ! --More--  ! ipv6 router rip R4Rip ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R4# R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv router rip R1Rip R1(config-rtr)#dis R1(config-rtr)#dist? distance distribute-list R1(config-rtr)#distr R1(config-rtr)#distribute-list ? prefix-list Filter connections based on an IPv6 prefix-list R1(config-rtr)#distribute-list                 exit R1(config)#ipv pr R1(config)#ipv prefix-list ? WORD Name of a prefix list sequence-number Include/exclude sequence numbers in NVGEN R1(config)#ipv prefix-list Prov b3 ? deny Specify packets to reject description Prefix-list specific description permit Specify packets to forward seq sequence number of an entry R1(config)#ipv prefix-list Prob3 den ? X:X:X:X::X/<0-128> IPv6 prefix / R1(config)#ipv prefix-list Prob3 den 2000:4:4::/64 ? ge Minimum prefix length to be matched le Maximum prefix length to be matched R1(config)#ipv prefix-list Prob3 den 2000:4:4::/64 R1(config)#do sh ipv route IPv6 Routing Table - 7 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/2] via FE80::2D0:BAFF:FED3:BA40, Ethernet0/1 C 2005:0:102::/64 [0/0] via ::, Serial0/1 L 2005:0:102:0:20A:8AFF:FEF0:D980/128 [0/0] via ::, Serial0/1 C 2005:0:104::/64 [0/0] via ::, Ethernet0/1 L 2005:0:104:0:20A:8AFF:FEF0:D981/128 [0/0] via ::, Ethernet0/1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R1(config)#q do sh ipv routeipv prefix-list Prob3 den 2000:4:4::/64                   per ::/0 le 128 R1(config)#ipv prefix-list Prob3 per ::/0 le 128do sh ipv route ipv prefix-list Prob3 den 2000:4:4::/64 exit ipv router rip R1Rip R1(config-rtr)#distr R1(config-rtr)#distribute-list pre R1(config-rtr)#distribute-list prefix-list Prob3 out ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface Ethernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R1(config-rtr)#distribute-list prefix-list Prob3 out ser 1/  0. /1 ? R1(config-rtr)#distribute-list prefix-list Prob3 out ser 0/1 R1(config-rtr)#^Z R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh ipv   v route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   via ::, Serial1/2 L 2005:0:1203:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#cle p ipv route * R2#cle ipv route *sh ipv route  IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   R2#sh ipb  v  v rip data RIP process "R2Rip", local RIB 2000:4:4::/64, metric 3, installed Serial1/1/FE80::20A:8AFF:FEF0:D980, expires in 121 secs 2005:0:102::/64, metric 2 Serial1/1/FE80::20A:8AFF:FEF0:D980, expires in 177 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::20A:8AFF:FEF0:D980, expires in 177 secs R2#clea ipv rip R2#clea ipv rip sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip dataclea ipv rip sh ipv rip dataoute cle ipv route * R2#cle ipv route *sh ipv rip dataclea ipv rip sh ipv rip dataclea ipv rip sh ipv rip data RIP process "R2Rip", local RIB 2005:0:102::/64, metric 2 Serial1/1/FE80::20A:8AFF:FEF0:D980, expires in 174 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::20A:8AFF:FEF0:D980, expires in 174 secs R2#sh ipv route IPv6 Routing Table - 11 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203:0:213:60FF:FEF0:FD40/128 [0/0] --More--   via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b ipv router R3#sh run | b ipv router6 router R3#sh ru   un | b router R3#sh run Building configuration... Current configuration : 1450 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R3 ! boot-start-marker boot-end-marker ! ! no network-clock-participate slot 1 no network-clock-participate wic 0 no aaa new-model ip subnet-zero ! ! ! ip cef no ip domain lookup --More--  ip audit po max-events 100 ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 --More--   R3#^x1 % Unknown command or computer name, or unable to find computer address R3# R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] * R1#sh run | b ipv router R1#sh run | b ipv router6 router ipv6 router rip R1Rip distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1# R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int     do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 unassigned YES manual up up Serial1/0.1 unassigned YES unset up up Serial1/0.2 unassigned YES unset up up Serial1/1 unassigned YES unset up up Serial1/2 unassigned YES unset up up Serial1/3 unassigned YES unset administratively down down --More--  Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down R2(config)#int s 1/2 R2(config-if)#ipv ospf ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R2(config-if)#ipv ospf 1  ? area Set the OSPF area ID R2(config-if)#ipv ospf 1 area 0 ? instance Set the OSPF instance R2(config-if)#ipv ospf 1 area 0 R2(config-if)# *Mar 1 07:12:14.400: %OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id, please configure manually R2(config-if)# R2(config-if)# R2(config-if)# R2(config-if)#ipv router ospf 1 R2(config-rtr)#router R2(config-rtr)#router-id 2.2.2.2 R2(config-rtr)#do sh       ^Z R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ipv router ospf 1 R3(config-rtr)# *Mar 1 07:14:02.229: %OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id, please configure manually R3(config-rtr)# R3(config-rtr)# R3(config-rtr)#router R3(config-rtr)#router-id 3.3.3.3 R3(config-rtr)#int s 1/2 R3(config-if)#ipv ospf 1 area 0 R3(config-if)#int lo 0 R3(config-if)#ipv ospf 1 *Mar 1 07:14:36.649: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/2 from LOADING to FULL, Loading Done R3(config-if)#ipv ospf 1 area 51 R3(config-if)#^Z R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] * R2#ah ru     sh run | b interface Serial1/2 interface Serial1/2 no ip address ipv6 address 2005:0:1203::/64 eui-64 ipv6 ospf 1 area 0 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 --More--   no ip address shutdown ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes ! ipv6 router rip R2Rip ! ! ! ! ! ! ! ! ! ! --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run | b interface Lo interface Loopback0 no ip address ipv6 address 2000:3:3::/64 eui-64 ipv6 ospf 1 area 51 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay --More--   ipv6 address 2005:0:237::/64 eui-64 frame-relay map ipv6 2005:0:237:0:212:43FF:FEAC:6F60 307 broadcast frame-relay map ipv6 2005:0:237:0:213:60FF:FEF0:FD40 302 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::/64 eui-64 ipv6 ospf 1 area 0 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address --More--   shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 3.3.3.3 log-adjacency-changes ! ! ! ! ! --More--   R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipv router ospf 1 R2(config-rtr)#redis R2(config-rtr)#redistribute rip ? WORD User selected string identifying this process R2(config-rtr)#redistribute rip R2Rip ? metric Metric for redistributed routes metric-type OSPF/IS-IS exterior metric type for redistributed routes route-map Route map reference tag Set tag for routes redistributed into OSPF R2(config-rtr)#redistribute rip R2Rip tag 22  ? metric Metric for redistributed routes metric-type OSPF/IS-IS exterior metric type for redistributed routes route-map Route map reference R2(config-rtr)#redistribute rip R2Rip tag 2 R2(config-rtr)#ipv router rip R1Rip R2(config-rtr)#ipv router rip R1Ripnipv router rip R1Rippipv router rip R1Ripoipv router rip R1Rip ipv router rip R1Ripipv router rip R1Rip ipv router rip R1Rip ipv router rip R1Rip oipv router rip R1Rip ipv router rip R1Rip R2(config)#no ipv router rip R1Ripipv router rip R1Rip no ipv router rip R1Ripipv router rip R1Rip Rip 2Rip R2(config-rtr)#res di R2(config-rtr)#redistribute ospf 1 ? match Redistribution of OSPF routes metric Metric for redistributed routes route-map Route map reference R2(config-rtr)#redistribute ospf 1 me R2(config-rtr)#redistribute ospf 1 metric ? <0-16> Default metric transparent Transparently redistribute metric R2(config-rtr)#redistribute ospf 1 metric 2 ? match Redistribution of OSPF routes route-map Route map reference R2(config-rtr)#redistribute ospf 1 metric 2 R2(config-rtr)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#ship   ip  v route IPv6 Routing Table - 8 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3:0:213:7FFF:FE12:A4E0/128 [120/3] via FE80::213:60FF:FEF0:FD40, Serial0/1 R 2000:4:4::/64 [120/2] via FE80::2D0:BAFF:FED3:BA40, Ethernet0/1 C 2005:0:102::/64 [0/0] via ::, Serial0/1 L 2005:0:102:0:20A:8AFF:FEF0:D980/128 [0/0] via ::, Serial0/1 C 2005:0:104::/64 [0/0] via ::, Ethernet0/1 L 2005:0:104:0:20A:8AFF:FEF0:D981/128 [0/0] via ::, Ethernet0/1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R1#p 2000:3:3:0:213:7FFF:FE12:A4E0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3:0:213:7FFF:FE12:A4E0, timeout is 2 seconds: .... RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#p 2000:3:3:0:213:7FFF:FE12:A4E0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3:0:213:7FFF:FE12:A4E0, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/64 ms R4# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-rtr)#redistribute ospf 1 metric 2 ipv router rip R2Rip no ipv router rip R1Ripipv router rip R2Rip redistribute ospf 1 metric 2  redis R2(config-rtr)#redistribute con R2(config-rtr)#redistribute connected 1 ^ % Invalid input detected at '^' marker. R2(config-rtr)#redistribute connected 1   met 1 R2(config-rtr)#ipv router ospf 1 R2(config-rtr)#ipv router ospf 1redistribute connected met 1      R2(config-rtr)#^x1 ^ % Invalid input detected at '^' marker. R2(config-rtr)# R2(config-rtr)# RACK13AS>1 [Resuming connection 1 to r1 ... ] . Suc R1#p 2000:3:3:0:213:7FFF:FE12:A4E0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3:0:213:7FFF:FE12:A4E0, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/61 ms R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-rtr)#^Z R2#sh run *Mar 1 07:23:08.220: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b router ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes redistribute connected redistribute rip R2Rip tag 2 ! ipv6 router rip R2Rip redistribute connected metric 1 redistribute ospf 1 metric 2 ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)#ipv ospf 1 area 0 R2(config-subif)#ipv ospf 1 area 0nt s 1/0.1  2 R2(config-subif)#int s 1/0.2pv ospf 1 area 0 R2(config-subif)# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int     ipv router ospf 1 R7(config-rtr)#router   R7(config-rtr)#router-id 7.7.7.7 R7(config-rtr)#int s 0 1/0.1 R7(config-subif)#ipv ospv f 1 area 0 R7(config-subif)#ipv ospf 1 area 0nt s 1/0.1  2 R7(config-subif)#int s 1/0.2pv ospf 1 area 0 R7(config-subif)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#int s 1/0pv ospf 1 area 51  0 R3(config-if)#^Z R3# *Mar 1 07:25:35.690: %SYS-5-CONFIG_I: Configured from console by console R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:35 11 Serial1/2 R3#deb ipv ospf ? adj OSPF adjacency events database-timer OSPF database timer events OSPF events flood OSPF flooding hello OSPF hello events lsa-generation OSPF lsa generation lsdb OSPF database modifications packet OSPF packets retransmission OSPF retransmission events spf OSPF spf R3#deb ipv ospf ev OSPFv3 events debugging is on R3#deb ipv ospf ev \    pac OSPFv3 packet debugging is on R3# *Mar 1 07:26:04.994: OSPFv3: rcv. v:3 t:1 l:36 rid:7.7.7.7 aid:0.0.0.0 chk:3B48 inst:0 from Serial1/0 R3# *Mar 1 07:26:06.709: OSPFv3: rcv. v:3 t:1 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:9A2C inst:0 from Serial1/0 *Mar 1 07:26:06.765: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 R3# *Mar 1 07:26:14.910: OSPFv3: rcv. v:3 t:1 l:36 rid:7.7.7.7 aid:0.0.0.0 chk:3B48 inst:0 from Serial1/0 R3# *Mar 1 07:26:16.725: OSPFv3: rcv. v:3 t:1 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:9A2C inst:0 from Serial1/0 *Mar 1 07:26:16.765: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 R3# *Mar 1 07:26:24.927: OSPFv3: rcv. v:3 t:1 l:36 rid:7.7.7.7 aid:0.0.0.0 chk:3B48 inst:0 from Serial1/0 R3# *Mar 1 07:26:26.742: OSPFv3: rcv. v:3 t:1 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:9A2C inst:0 from Serial1/0 *Mar 1 07:26:26.766: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 R3# *Mar 1 07:26:34.943: OSPFv3: rcv. v:3 t:1 l:36 rid:7.7.7.7 aid:0.0.0.0 chk:3B48 inst:0 from Serial1/0 R3# *Mar 1 07:26:36.758: OSPFv3: rcv. v:3 t:1 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:9A2C inst:0 from Serial1/0 *Mar 1 07:26:36.766: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 R3#u all All possible debugging has been turned off R3#ip  deb ipv ospf ? adj OSPF adjacency events database-timer OSPF database timer events OSPF events flood OSPF flooding hello OSPF hello events lsa-generation OSPF lsa generation lsdb OSPF database modifications packet OSPF packets retransmission OSPF retransmission events spf OSPF spf R3#deb ipv ospf adj OSPFv3 adjacency events debugging is on R3#deb ipv ospf adj   pack ? R3#deb ipv ospf pack                   u all All possible debugging has been turned off R3#sh ipv ospf int s 1/0 Serial1/0 is up, line protocol is up Link Local Address FE80::213:7FFF:FE12:A4E0, Interface ID 9 Area 0, Process ID 1, Instance ID 0, Router ID 3.3.3.3 Network Type NON_BROADCAST, Cost: 781 Transmit Delay is 1 sec, State WAITING, Priority 1 No designated router on this network No backup designated router on this network Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 Hello due in 00:00:08 Wait time before Designated router selection 00:00:08 Index 1/2/3, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] *M R2(config-subif)#do sh ipv ospf int s 10/  /0.1 Serial1/0.1 is up, line protocol is up Link Local Address FE80::213:60FF:FEF0:FD40, Interface ID 27 Area 0, Process ID 1, Instance ID 0, Router ID 2.2.2.2 Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:07 Index 1/2/2, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) R2(config-subif)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ipv ospf ne R3(config-if)#ipv ospf ne  1 net R3(config-if)#ipv ospf 1 net   ? area Set the OSPF area ID R3(config-if)#ipv ospf 1     ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R3(config-if)#ipv ospf net R3(config-if)#ipv ospf network ? broadcast Specify OSPF broadcast multi-access network non-broadcast Specify OSPF NBMA network point-to-multipoint Specify OSPF point-to-multipoint network point-to-point Specify OSPF point-to-point network R3(config-if)#ipv ospf network po R3(config-if)#ipv ospf network point-to-p R3(config-if)#ipv ospf network point-to-point       m R3(config-if)#ipv ospf ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R3(config-if)#ipv ospf hello-interval 10 ? R3(config-if)#ipv ospf hello-interval 10 R3(config-if)#do sh ipv ospf int s 1/0 Serial1/0 is up, line protocol is up Link Local Address FE80::213:7FFF:FE12:A4E0, Interface ID 9 Area 0, Process ID 1, Instance ID 0, Router ID 3.3.3.3 Network Type POINT_TO_MULTIPOINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:00 Index 1/2/3, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 2, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# *Mar 1 07:32:59.317: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from EXSTART to DOWN, Neighbor Down: Too many retransmits R3(config-if)# *Mar 1 07:33:59.319: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from DOWN to DOWN, Neighbor Down: Ignore timer expired R3(config-if)# *Mar 1 07:36:19.329: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from EXSTART to DOWN, Neighbor Down: Too many retransmits R3(config-if)# *Mar 1 07:37:19.331: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from DOWN to DOWN, Neighbor Down: Ignore timer expired R3(config-if)#do sh ipv ospf int s 1/0ipv ospf hello-interval 10 network point-to-mnt s 1/0 pv ospf network point-to-mhello-interval 10 do sh ipv ospf int s 1/0  fram map ipv FE80::212:43FF:FEAC:6F60 307 br R3(config-if)#fram map ipv *Mar 1 07:38:49.579: %OSPFv3-5-ADJCHG: Process 1, Nbr 7.7.7.7 on Serial1/0 from LOADING to FULL, Loading Done R3(config-if)#fram map ipv FE80::213:60FF:FEF0:FD40 302 br R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# *Mar 1 07:39:14.620: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from LOADING to FULL, Loading Done R3(config-if)# RACK13AS>7 [Resuming connection 7 to r7 ... ] *Ma R7(config-subif)#^Z R7#sh ip *Mar 1 07:39:40.098: %SYS-5-CONFIG_I: Configured from console by console R7#sh ip  v route IPv6 Routing Table - 11 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.2 O 2005:0:1203::/64 [110/1562] --More--   via FE80::213:60FF:FEF0:FD40, Serial1/0.2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip  v route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3:0:213:7FFF:FE12:A4E0/128 [120/4] via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4:0:2D0:BAFF:FED3:BA40/128 [0/0] via ::, Loopback0 R 2005:0:102::/64 [120/2] via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104:0:2D0:BAFF:FED3:BA40/128 [0/0] via ::, FastEthernet0/0 R 2005:0:237::/64 [120/3] via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 R 2005:0:237:0:213:7FFF:FE12:A4E0/128 [120/4] via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 R 2005:0:702::/64 [120/3] --More--   via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 R 2005:0:1203::/64 [120/3] via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R4# RACK13AS>2 [Resuming connection 2 to r2 ... ] * R2(config-subif)#^Z R2#sh *Mar 1 07:40:23.357: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b intere face Serial  1/0 interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::/64 eui-64 ipv6 ospf 1 area 0 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::/64 eui-64 ipv6 ospf 1 area 0 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::/64 eui-64 ipv6 rip R2Rip enable ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::/64 eui-64 ipv6 ospf 1 area 0 --More--   R2#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 7.7.7.7 1 FULL/ - 00:00:37 28 Serial1/0.2 3.3.3.3 1 FULL/ - 00:00:38 9 Serial1/0.1 3.3.3.3 1 FULL/ - 00:00:32 11 Serial1/2 R2#sh ipv ospf nei        io  ospf data OSPFv3 Router with ID (2.2.2.2) (Process ID 1) Router Link States (Area 0) ADV Router Age Seq# Fragment ID Link count Bits 2.2.2.2 153 0x8000000C 0 3 E 3.3.3.3 154 0x8000000C 0 3 B 7.7.7.7 179 0x80000008 0 2 None Inter Area Prefix Link States (Area 0) ADV Router Age Seq# Prefix 3.3.3.3 1619 0x80000001 2000:3:3:0:213:7FFF:FE12:A4E0/128 Link (Type-8) Link States (Area 0) ADV Router Age Seq# Link ID Interface 2.2.2.2 1056 0x80000001 28 Se1/0.2 7.7.7.7 990 0x80000001 28 Se1/0.2 2.2.2.2 1061 0x80000001 27 Se1/0.1 3.3.3.3 714 0x80000001 9 Se1/0.1 2.2.2.2 1751 0x80000001 11 Se1/2 --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#fram map ipv FE80::213:60FF:FEF0:FD40 302 br2:43FF:FEAC:6F60 307 brmfram map ipv FE80::212:43FF:FEAC:6F60 307 brfram map ipv FE80::212:43FF:FEAC:6F60 307 br nfram map ipv FE80::212:43FF:FEAC:6F60 307 brofram map ipv FE80::212:43FF:FEAC:6F60 307 br fram map ipv FE80::212:43FF:FEAC:6F60 307 br R3(config-if)#do s deb ipv ospf adj OSPFv3 adjacency events debugging is on R3(config-if)#do sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:37 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:35 27 Serial1/0 2.2.2.2 1 FULL/ - 00:00:37 11 Serial1/2 R3(config-if)#do sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:37 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:35 27 Serial1/0 2.2.2.2 1 FULL/ - 00:00:37 11 Serial1/2 R3(config-if)#do sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:35 27 Serial1/0 7.7.7.7 1 FULL/ - 00:00:33 27 Serial1/0 2.2.2.2 1 FULL/ - 00:00:35 11 Serial1/2 R3(config-if)# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:36 28 Serial1/0.2 3.3.3.3 1 FULL/ - 00:00:34 9 Serial1/0.1 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:33 28 Serial1/0.2 3.3.3.3 1 FULL/ - 00:00:31 9 Serial1/0.1 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:30 28 Serial1/0.2 3.3.3.3 1 FULL/ - 00:00:38 9 Serial1/0.1 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:39 28 Serial1/0.2 3.3.3.3 1 FULL/ - 00:00:37 9 Serial1/0.1 R7# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#shut R3(config-if)# *Mar 1 07:43:11.893: OSPFv3: Interface Serial1/0 going Down *Mar 1 07:43:11.893: OSPFv3: 2.2.2.2 address FE80::213:60FF:FEF0:FD40 on Serial1/0 is dead, state DOWN *Mar 1 07:43:11.893: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 07:43:11.893: OSPFv3: 7.7.7.7 address FE80::212:43FF:FEAC:6F60 on Serial1/0 is dead, state DOWN R3(config-if)# *Mar 1 07:43:11.897: %OSPFv3-5-ADJCHG: Process 1, Nbr 7.7.7.7 on Serial1/0 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)#no shut R3(config-if)# *Mar 1 07:43:13.893: %LINK-5-CHANGED: Interface Serial1/0, changed state to administratively down *Mar 1 07:43:14.894: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to down R3(config-if)# *Mar 1 07:43:15.832: OSPFv3: Interface Serial1/0 going Up R3(config-if)# *Mar 1 07:43:17.823: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up *Mar 1 07:43:18.825: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up R3(config-if)#do sh ipv ospf pack sh ipv ospf pack ^ % Invalid input detected at '^' marker. R3(config-if)#do sh ipv ospf pack ipv ospf pack  ipv ospf pack d ipv ospf packe ipv ospf packb ipv ospf pack OSPFv3 packet debugging is on R3(config-if)# *Mar 1 07:43:45.372: OSPFv3: rcv. v:3 t:1 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:9A2C inst:0 from Serial1/0 *Mar 1 07:43:46.069: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:843C inst:0 from Serial1/0 *Mar 1 07:43:46.069: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x1169 opt 0x0013 flag 0x7 len 28 mtu 1500 state INIT *Mar 1 07:43:46.069: OSPFv3: 2 Way Communication to 2.2.2.2 on Serial1/0, state 2WAY *Mar 1 07:43:46.073: OSPFv3: Send DBD to 2.2.2.2 on Serial1/0 seq 0x25C5 opt 0x0013 flag 0x7 len 28 *Mar 1 07:43:46.073: OSPFv3: First DBD and we are not SLAVE *Mar 1 07:43:46.226: OSPFv3: rcv. v:3 t:2 l:248 rid:2.2.2.2 aid:0.0.0.0 chk:4A32 inst:0 from Serial1/0 *Mar 1 07:43:46.226: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x25C5 opt 0x0013 flag 0x2 len 248 mtu 1500 state EXSTART *Mar 1 07:43:46.226: OSPFv3: NBR Negotiation Done. We are the MASTER *Mar 1 07:43:46.226: OSPFv3: Send DBD to 2.2.2.2 on Serial1/0 seq 0x25C6 opt 0x0013 flag R3(config-if)# 0x3 len 228 *Mar 1 07:43:46.230: OSPFv3: Database request to 2.2.2.2 *Mar 1 07:43:46.230: OSPFv3: sent LS REQ packet to FE80::213:60FF:FEF0:FD40, length 12 *Mar 1 07:43:46.370: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:6FE6 inst:0 from Serial1/0 *Mar 1 07:43:46.370: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x25C6 opt 0x0013 flag 0x0 len 28 mtu 1500 state EXCHANGE *Mar 1 07:43:46.370: OSPFv3: Send DBD to 2.2.2.2 on Serial1/0 seq 0x25C7 opt 0x0013 flag 0x1 len 28 *Mar 1 07:43:46.382: OSPFv3: rcv. v:3 t:3 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:9583 inst:0 from Serial1/0 *Mar 1 07:43:46.402: OSPFv3: rcv. v:3 t:4 l:76 rid:2.2.2.2 aid:0.0.0.0 chk:B41B inst:0 from Serial1/0 *Mar 1 07:43:46.470: OSPFv3: rcv. v:3 t:2 l:28 rid:2.2.2.2 aid:0.0.0.0 chk:6FE5 inst:0 from Serial1/0 *Mar 1 07:43:46.470: OSPFv3: Rcv DBD from 2.2.2.2 on Serial1/0 seq 0x25C7 opt 0x0013 flag 0x0 len 28 mtu 1500 state EXCHANGE *Mar 1 07:43:46.470: OSPFv3: Exchange Done with 2.2.2.2 on Serial1/0 *Mar 1 07:43:46.474: OSPFv3: Synchronized with 2.2.2.2 on Serial1/0, state FULL *Mar 1 07:43:46.474: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from LOADING to FULL, Loading Done *Mar 1 07:43:46.863: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 *Mar 1 07:43:46.963: OSPFv3: rcv. v:3 t:4 l:92 rid:2.2.2.2 aid:0.0.0.0 chk:377B inst:0 from Serial1/2 *Mar 1 07:43:47.007: OSPFv3: rcv. v:3 t:4 l:92 rid:2.2.2.2 aid:0.0.0.0 chk:377B inst:0 from Serial1/0 *Mar 1 07:43:47.199: OSPFv3: rcv. v:3 t:4 l:76 rid:2.2.2.2 aid:0.0.0.0 chk:D9F7 inst:0 from Serial1/0 *Mar 1 07:43:47.936: OSPFv3: rcv. v:3 t:4 l:76 rid:2.2.2.2 aid:0.0.0.0 chk:8051 inst:0 from Serial1/2 *Mar 1 07:43:47.984: OSPFv3: rcv. v:3 t:4 l:76 rid:2.2.2.2 aid:0.0.0.0 chk:8051 inst:0 from Serial1/0 R3(config-if)# R3(config-if)# *Mar 1 07:43:48.978: OSPFv3: rcv. v:3 t:5 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:BDC7 inst:0 from Serial1/0 *Mar 1 07:43:49.535: OSPFv3: rcv. v:3 t:5 l:36 rid:2.2.2.2 aid:0.0.0.0 chk:EBD7 inst:0 from Serial1/2 *Mar 1 07:43:49.884: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:353A inst:0 from Serial1/0 *Mar 1 07:43:49.884: OSPFv3: 2 Way Communication to 7.7.7.7 on Serial1/0, state 2WAY *Mar 1 07:43:49.884: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0x17A7 opt 0x0013 flag 0x7 len 28 R3(config-if)# *Mar 1 07:43:54.884: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0x17A7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:43:54.884: OSPFv3: Retransmitting DBD to 7.7.7.7 on Serial1/0 [1] *Mar 1 07:43:55.288: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:941E inst:0 from Serial1/0 R3(config-if)# *Mar 1 07:43:56.022: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:28EA inst:0 from Serial1/0 *Mar 1 07:43:56.022: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x7 len 28 mtu 1500 state EXSTART *Mar 1 07:43:56.022: OSPFv3: NBR Negotiation Done. We are the SLAVE *Mar 1 07:43:56.022: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x2 len 228 *Mar 1 07:43:56.863: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 R3(config-if)# *Mar 1 07:43:59.836: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:353A inst:0 from Serial1/0 R3(config-if)# *Mar 1 07:44:01.034: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:28EA inst:0 from Serial1/0 *Mar 1 07:44:01.034: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x7 len 28 mtu 1500 state EXCHANGE *Mar 1 07:44:01.034: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x2 len 228 R3(config-if)# *Mar 1 07:44:05.305: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:941E inst:0 from Serial1/0 *Mar 1 07:44:06.042: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:28EA inst:0 from Serial1/0 *Mar 1 07:44:06.042: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x7 len 28 mtu 1500 state EXCHANGE *Mar 1 07:44:06.042: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x2 len 228 R3(config-if)# *Mar 1 07:44:06.863: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 R3(config-if)# *Mar 1 07:44:09.852: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:353A inst:0 from Serial1/0 R3(config-if)# *Mar 1 07:44:11.050: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:28EA inst:0 from Serial1/0 *Mar 1 07:44:11.050: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x7 len 28 mtu 1500 state EXCHANGE *Mar 1 07:44:11.050: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x2 len 228 R3(config-if)# *Mar 1 07:44:15.325: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:941E inst:0 from Serial1/0 *Mar 1 07:44:16.058: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:28EA inst:0 from Serial1/0 *Mar 1 07:44:16.058: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x7 len 28 mtu 1500 state EXCHANGE *Mar 1 07:44:16.058: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x2 len 228 R3(config-if)# *Mar 1 07:44:16.864: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 R3(config-if)# *Mar 1 07:44:19.869: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:353A inst:0 from Serial1/0 R3(config-if)#do u *Mar 1 07:44:21.067: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:28EA inst:0 from Serial1/0 *Mar 1 07:44:21.067: OSPFv3: Rcv DBD from 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x7 len 28 mtu 1500 state EXCHANGE *Mar 1 07:44:21.067: OSPFv3: Send DBD to 7.7.7.7 on Serial1/0 seq 0xDD7 opt 0x0013 flag 0x2 len 228 R3(config-if)#do u all All possible debugging has been turned off R3(config-if)# RACK13AS>7 [Resuming connection 7 to r7 ... ] *M R7#d s deb ipv ospf adj OSPFv3 adjacency events debugging is on R7#deb ipv ospf adj  *Mar 1 07:44:50.395: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:44:50.395: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [8] R7#deb ipv ospf ad        *Mar 1 07:44:55.395: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:44:55.395: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [9] R7#deb ipv          *Mar 1 07:45:00.395: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:00.395: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [10] R7# *Mar 1 07:45:05.395: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:05.395: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [11] R7# *Mar 1 07:45:10.395: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:10.395: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [12] R7# *Mar 1 07:45:15.396: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:15.396: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [13] R7# *Mar 1 07:45:20.396: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:20.396: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [14] R7# *Mar 1 07:45:25.396: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:25.396: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [15] R7# *Mar 1 07:45:30.396: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:30.396: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [16] R7# *Mar 1 07:45:35.396: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:35.396: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [17] R7# *Mar 1 07:45:40.397: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:40.397: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [18] R7# *Mar 1 07:45:45.397: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:45.397: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [19] R7# *Mar 1 07:45:50.397: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0xDD7 opt 0x0013 flag 0x7 len 28 *Mar 1 07:45:50.397: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [20] R7#u all All possible debugging has been turned off R7# RACK13AS> [Resuming connection 7 to r7 ... ] RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh    deb ipv pack IPv6 unicast packet debugging is on R3(config-if)# *Mar 1 07:46:05.850: IPV6: source FE80::213:7FFF:FE12:A4E0 (local) *Mar 1 07:46:05.850: dest FF02::5 (Serial1/0) *Mar 1 07:46:05.850: traffic class 224, flow 0x0, len 84+0, prot 89, hops 1, originating *Mar 1 07:46:05.850: IPv6: Sending on Serial1/0 *Mar 1 07:46:06.664: IPV6: source FE80::213:7FFF:FE12:A4E0 (local) *Mar 1 07:46:06.664: dest FE80::212:43FF:FEAC:6F60 (Serial1/0) *Mar 1 07:46:06.664: traffic class 224, flow 0x0, len 100+0, prot 89, hops 1, originating *Mar 1 07:46:06.664: IPv6: Encapsulation failed *Mar 1 07:46:06.664: IPV6: source FE80::213:7FFF:FE12:A4E0 (local) *Mar 1 07:46:06.664: dest FE80::213:60FF:FEF0:FD40 R3(config-if)# (Serial1/0) *Mar 1 07:46:06.664: traffic class 224, flow 0x0, len 100+0, prot 89, hops 1, originating *Mar 1 07:46:06.668: IPv6: Sending on Serial1/0 R3(config-if)#do u *Mar 1 07:46:09.132: IPV6: source FE80::213:7FFF:FE12:A4E0 (local) *Mar 1 07:46:09.132: dest FF02::5 (Serial1/2) *Mar 1 07:46:09.132: traffic class 224, flow 0x0, len 76+0, prot 89, hops 1, originating *Mar 1 07:46:09.132: IPv6: Sending on Serial1/2 R3(config-if)#do u all All possible debugging has been turned off R3(config-if)#do u alldeb ipv packu all deb ipv ospf pack RACK13AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:32 28 Serial1/0.2 3.3.3.3 1 EXSTART/ - 00:00:37 9 Serial1/0.1 R7# RACK13AS> [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#logg buff R7(config)#^Z R7#sh lo *Mar 1 07:48:21.373: %SYS-5-CONFIG_I: Configured from console by console R7#sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 90 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 1 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 70 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 07:48:21.373: %SYS-5-CONFIG_I: Configured from console by console R7#q  RACK13AS>3 [Resuming connection 3 to r3 ... ] OSPFv3 packet debugging is on R3(config-if)#shut *Mar 1 07:48:16.873: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 R3(config-if)#shut R3(config-if)# *Mar 1 07:48:19.105: %OSPFv3-5-ADJCHG: Process 1, Nbr 7.7.7.7 on Serial1/0 from EXCHANGE to DOWN, Neighbor Down: Interface down or detached *Mar 1 07:48:19.105: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#deb ipv pack IPv6 unicast packet debugging is on R7# RACK13AS> [Resuming connection 7 to r7 ... ] *Mar 1 07:48:42.175: IPV6: source FE80::212:43FF:FEAC:6F60 (local) *Mar 1 07:48:42.175: dest FF02::5 (Serial1/0.2) *Mar 1 07:48:42.175: traffic class 224, flow 0x0, len 80+0, prot 89, hops 1, originating *Mar 1 07:48:42.175: IPv6: Sending on Serial1/0.2 *Mar 1 07:48:42.832: IPV6: source FE80::212:43FF:FEAC:6F60 (local) *Mar 1 07:48:42.832: dest FF02::5 (Serial1/0.2) *Mar 1 07:48:42.832: traffic class 224, flow 0x0, len 96+0, prot 89, hops 1, originating *Mar 1 07:48:42.832: IPv6: Sending on Serial1/0.2 R7# *Mar 1 07:48:44.246: %OSPFv3-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Serial1/0.1 from EXSTART to DOWN, Neighbor Down: Interface down or detached R7# *Mar 1 07:48:44.779: IPV6: source FE80::212:43FF:FEAC:6F60 (local) *Mar 1 07:48:44.779: dest FF02::5 (Serial1/0.2) *Mar 1 07:48:44.779: traffic class 224, flow 0x0, len 144+0, prot 89, hops 1, originating *Mar 1 07:48:44.779: IPv6: Sending on Serial1/0.2 R7#u all All possible debugging has been turned off R7#ip  deb ikp  pv ospf adj OSPFv3 adjacency events debugging is on R7# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-if)#no shut R3(config-if)# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7# *Mar 1 07:49:04.251: OSPFv3: Interface Serial1/0.1 going Up R7# *Mar 1 07:49:14.247: OSPFv3: Interface Serial1/0.1 going Down R7# *Mar 1 07:49:24.252: OSPFv3: Interface Serial1/0.1 going Up R7# *Mar 1 07:49:41.724: OSPFv3: 2 Way Communication to 3.3.3.3 on Serial1/0.1, state 2WAY *Mar 1 07:49:41.724: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0x571 opt 0x0013 flag 0x7 len 28 R7# *Mar 1 07:49:46.724: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0x571 opt 0x0013 flag 0x7 len 28 *Mar 1 07:49:46.724: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [1] R7# *Mar 1 07:49:51.725: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0x571 opt 0x0013 flag 0x7 len 28 *Mar 1 07:49:51.725: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [2] R7# *Mar 1 07:49:56.725: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0x571 opt 0x0013 flag 0x7 len 28 *Mar 1 07:49:56.725: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [3] R7# *Mar 1 07:50:01.725: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0x571 opt 0x0013 flag 0x7 len 28 *Mar 1 07:50:01.725: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [4] R7# *Mar 1 07:50:06.725: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0x571 opt 0x0013 flag 0x7 len 28 *Mar 1 07:50:06.725: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [5] R7# *Mar 1 07:50:11.725: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0x571 opt 0x0013 flag 0x7 len 28 *Mar 1 07:50:11.725: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [6] R7# *Mar 1 07:50:16.726: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0x571 opt 0x0013 flag 0x7 len 28 *Mar 1 07:50:16.726: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [7] R7# *Mar 1 07:50:21.726: OSPFv3: Send DBD to 3.3.3.3 on Serial1/0.1 seq 0x571 opt 0x0013 flag 0x7 len 28 *Mar 1 07:50:21.726: OSPFv3: Retransmitting DBD to 3.3.3.3 on Serial1/0.1 [8] R7# RACK13AS>3 [Resuming connection 3 to r3 ... ] *M R3(config-if)# *Mar 1 07:50:12.342: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:3150 inst:0 from Serial1/0 R3(config-if)#no shutshut  *Mar 1 07:50:14.474: OSPFv3: rcv. v:3 t:4 l:60 rid:2.2.2.2 aid:0.0.0.0 chk:8B67 inst:0 from Serial1/2 *Mar 1 07:50:14.578: OSPFv3: rcv. v:3 t:4 l:60 rid:2.2.2.2 aid:0.0.0.0 chk:8B67 inst:0 from Serial1/0 *Mar 1 07:50:15.464: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:941E inst:0 from Serial1/0 R3(config-if)#shutdo deb ipv ospf packshut no shut  *Mar 1 07:50:16.878: OSPFv3: rcv. v:3 t:1 l:40 rid:2.2.2.2 aid:0.0.0.0 chk:942E inst:0 from Serial1/2 *Mar 1 07:50:17.363: OSPFv3: rcv. v:3 t:2 l:28 rid:7.7.7.7 aid:0.0.0.0 chk:3150 inst:0 from Serial1/0 R3(config-if)#do u all All possible debugging has been turned off R3(config-if)#do u allno shut shut  *Mar 1 07:50:19.871: OSPFv3: rcv. v:3 t:1 l:40 rid:7.7.7.7 aid:0.0.0.0 chk:353A inst:0 from Serial1/0 R3(config-if)#shutdo deb ipv ospf packu all deb ipv packu all deb ipv ospf packsh ipv ospf pack no shut shut do sh ipv ospf neideb ipv ospf adjno fram map ipv FE80::212:43FF:FEAC:6F60 307 brfram map ipv FE80::213:60FF:FEF0:FD40 302 br no fram map ipv FE80::212:43FF:FEAC:6F60 307 brno fram map ipv FE80::212:43FF:FEAC:6F60 307 br  fram map ipv FE80::212:43FF:FEAC:6F60 307 br  R3(config-if)#^Z R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] *M R2# RACK13AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#u all All possible debugging has been turned off R7# RACK13AS>22~ % Unknown command or computer name, or unable to find computer address RACK13AS> [Resuming connection 7 to r7 ... ] R7# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#no shut R3(config-if)#^Z R3# *Mar 1 07:51:06.131: %SYS-5-CONFIG_I: Configured from console by console R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | i   b intert face Serial  1/0 interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::/64 eui-64 ipv6 ospf 1 area 0 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::/64 eui-64 ipv6 ospf 1 area 0 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::/64 eui-64 ipv6 rip R2Rip enable ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::/64 eui-64 ipv6 ospf 1 area 0 --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b     int s1/0 Building configuration... Current configuration : 452 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::/64 eui-64 ipv6 ospf network point-to-multipoint ipv6 ospf hello-interval 10 ipv6 ospf 1 area 0 frame-relay map ipv6 FE80::212:43FF:FEAC:6F60 307 broadcast frame-relay map ipv6 FE80::213:60FF:FEF0:FD40 302 broadcast frame-relay map ipv6 2005:0:237:0:212:43FF:FEAC:6F60 307 broadcast frame-relay map ipv6 2005:0:237:0:213:60FF:FEF0:FD40 302 broadcast end R3# R3# R3# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b interface Serial1/0 interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::/64 eui-64 ipv6 ospf 1 area 0 frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::/64 eui-64 ipv6 ospf 1 area 0 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 --More--   R7# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config tr ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0 2 R2(config-if)#int     ipv ospf 1 area 20 R2(config-if)#^Z R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#ip ospf 1 area 20 ^ % Invalid input detected at '^' marker. R3(config-if)#ip ospf 1 area 20pv ospf 1 area 20 R3(config-if)# *Mar 1 07:53:44.190: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)# *Mar 1 07:53:49.246: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/2 from LOADING to FULL, Loading Done R3(config-if)# RACK13AS> [Resuming connection 3 to r3 ... ] R3(config-if)#int s 1/2 R3(config-if)#int s 1/2 0 R3(config-if)#\shut ^ % Invalid input detected at '^' marker. R3(config-if)#\shut  \shutint s 1/0 R3(config-if)#shut R3(config-if)# *Mar 1 07:54:33.563: %OSPFv3-5-ADJCHG: Process 1, Nbr 7.7.7.7 on Serial1/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 07:54:33.563: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)# *Mar 1 07:54:35.558: %LINK-5-CHANGED: Interface Serial1/0, changed state to administratively down *Mar 1 07:54:36.560: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to down R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh ip  v route IPv6 Routing Table - 9 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] --More--   via ::, Null0 R2#sh ipv route 2000:3:3:: % Route not found R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh ipv route IPv6 Routing Table - 9 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3:0:213:7FFF:FE12:A4E0/128 [0/0] via ::, Loopback0 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/2 OI 2005:0:702::/64 [110/1562] via FE80::213:60FF:FEF0:FD40, Serial1/2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] --More--   via ::, Null0 R3(config-if)#do clea ipv route * R3(config-if)#do clea ipv route *sh ipv route  IPv6 Routing Table - 9 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3:0:213:7FFF:FE12:A4E0/128 [0/0] via ::, Loopback0 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/2 OI 2005:0:702::/64 [110/1562] via FE80::213:60FF:FEF0:FD40, Serial1/2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] --More--   R3(config-if)#ipv ospf > ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R3(config-if)#ipv ospf 1 ? area Set the OSPF area ID R3(config-if)#ipv ospf 1          1       exit R3(config)#ipv router ospf 1 R3(config-rtr)#? area OSPF area parameters auto-cost Calculate OSPF interface cost according to bandwidth default Set a command to its defaults default-information Distribution of default information default-metric Set metric of redistributed routes discard-route Enable or disable discard-route installation distance Administrative distance distribute-list Filter networks in routing updates exit Exit from IPv6 routing protocol configuration mode ignore Do not complain about specific event log-adjacency-changes Log changes in adjacency state maximum-paths Forward packets over multiple paths no Negate a command or set its defaults passive-interface Suppress routing updates on an interface redistribute Redistribute IPv6 prefixes from another routing protocol router-id router-id for this OSPF process summary-prefix Configure IPv6 summary prefix timers Adjust routing timers R3(config-rtr)#  area ? <0-4294967295> OSPF area ID as a decimal value A.B.C.D OSPF area ID in IP address format R3(config-rtr)#area 20 ? default-cost Set the summary default-cost of a NSSA/stub area nssa Specify a NSSA area range Summarize routes matching address/mask (border routers only) stub Specify a stub area virtual-link Define a virtual link and its parameters R3(config-rtr)#area 20 vi R3(config-rtr)#area 20 virtual-link ? A.B.C.D RouterID associated with virtual link neighbor R3(config-rtr)#area 20 virtual-link 2.2.2.2 ? dead-interval Dead router detection time hello-interval Hello packet interval retransmit-interval LSA retransmit interval transmit-delay LSA transmission delay R3(config-rtr)#area 20 virtual-link 2.2.2.2 R3(config-rtr)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int \     ipv router ospf 1 R2(config-rtr)#area 20 vir 3.3.3.3 R2(config-rtr)#^Z R2#sh ipv *Mar 1 07:58:13.720: %SYS-5-CONFIG_I: Configured from console by console R2#sh ipv ospf vi R2#sh ipv ospf virtual-links Virtual Link OSPF_VL0 to router 3.3.3.3 is up Interface ID 29, IPv6 address 2005:0:1203:0:213:7FFF:FE12:A4E0 Run as demand circuit DoNotAge LSA allowed. Transit area 20, via interface Serial1/2, Cost of using 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Adjacency State INIT (Hello suppressed) Index 0/0/0, retransmission queue length 0, number of retransmission 0 First 0x0(0)/0x0(0)/0x0(0) Next 0x0(0)/0x0(0)/0x0(0) Last retransmission scan length is 0, maximum is 0 Last retransmission scan time is 0 msec, maximum is 0 msec R2# *Mar 1 07:58:21.905: %OSPFv3-5-ADJCHG: Process 1, Nbr 3.3.3.3 on OSPF_VL0 from LOADING to FULL, Loading Done R2#sh ipv ospf virtual-links Virtual Link OSPF_VL0 to router 3.3.3.3 is up Interface ID 29, IPv6 address 2005:0:1203:0:213:7FFF:FE12:A4E0 Run as demand circuit DoNotAge LSA allowed. Transit area 20, via interface Serial1/2, Cost of using 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Adjacency State FULL (Hello suppressed) Index 1/1/3, retransmission queue length 1, number of retransmission 1 First 0x0(0)/0x83D8CEF4(88)/0x0(0) Next 0x0(0)/0x83D8CEF4(88)/0x0(0) Last retransmission scan length is 1, maximum is 1 Last retransmission scan time is 0 msec, maximum is 0 msec Link State retransmission due in 4792 msec R2#ah ip  v ospf             sh ipv ospf route ^ % Invalid input detected at '^' marker. R2#\sh ipv ospf route          route IPv6 Routing Table - 11 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/2 O 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [110/781] --More--   via FE80::213:7FFF:FE12:A4E0, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipv ospf      rpouter      outer ps    ospf 1 R2(config-rtr)#area 20 vi R2(config-rtr)#area 20 virtual-link ? A.B.C.D RouterID associated with virtual link neighbor R2(config-rtr)#area 20 virtual-link 3.3.3.3 ? dead-interval Dead router detection time hello-interval Hello packet interval retransmit-interval LSA retransmit interval transmit-delay LSA transmission delay R2(config-rtr)#area 20 virtual-link 3.3.3.3                              area 0 ? default-cost Set the summary default-cost of a NSSA/stub area nssa Specify a NSSA area range Summarize routes matching address/mask (border routers only) stub Specify a stub area virtual-link Define a virtual link and its parameters R2(config-rtr)#area 0        int s 1/2 R2(config-if)#area      int s     ipv ospf ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R2(config-if)#ipv ospf 1 ? area Set the OSPF area ID R2(config-if)#ipv ospf 1 area 20 ? instance Set the OSPF instance R2(config-if)#ipv ospf 1 area 20                    ipv > ? IPv6 interface subcommands: address Configure IPv6 address on interface cef Cisco Express Forwarding for IPv6 enable Enable IPv6 on interface mtu Set IPv6 Maximum Transmission Unit nat Enable IPv6 NAT on interface nd IPv6 interface Neighbor Discovery subcommands ospf OSPF interface commands redirects Enable sending of ICMP Redirect messages rip Configure RIP routing protocol router IPv6 Router interface commands traffic-filter Access control list for packets unnumbered Preferred interface for source address selection verify Enable per packet validation R2(config-if)#ipv osp  f ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R2(config-if)#ipv ospf 1 ? area Set the OSPF area ID R2(config-if)#ipv ospf 1 area ? <0-4294967295> OSPF area ID as a decimal value A.B.C.D OSPF area ID in IP address format R2(config-if)#ipv ospf 1 area 20 ? instance Set the OSPF instance R2(config-if)#ipv ospf 1 area 20                    exit R2(config)#exit R2# *Mar 1 08:03:59.010: %SYS-5-CONFIG_I: Configured from console by console R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *M R3(config-rtr)#int s 1/0 R3(config-if)#no shut R3(config-if)#^Z R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run int s 1/2 Building configuration... Current configuration : 119 bytes ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::/64 eui-64 ipv6 ospf 1 area 20 clock rate 64000 end R2#sh run int s 1/2         | b router ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes area 20 virtual-link 3.3.3.3 redistribute connected redistribute rip R2Rip tag 2 ! ipv6 router rip R2Rip redistribute connected metric 1 redistribute ospf 1 metric 2 ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous --More-- *Mar 1 08:04:34.993: %OSPFv3-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Serial1/0.1 from LOADING to FULL, Loading Done --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh run |     int s 1/2 Building configuration... Current configuration : 101 bytes ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::/64 eui-64 ipv6 ospf 1 area 20 end R3#sh run | b router ipv6 router ospf 1 router-id 3.3.3.3 log-adjacency-changes area 20 virtual-link 2.2.2.2 ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! --More--   R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0 R1(config-if)# *Mar 1 08:08:14.481: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#ipv add 3005      2005:17:15 7; ::1/64 R1(config-if)#tun spou   ou ether 0/0/  R1(config-if)#tun dest 180/.  .40.7.1 R1(config-if)# *Mar 1 08:10:21.144: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-if)#ipv rip E R1Rip en R1(config-if)# RACK13AS>7 [Resuming connection 7 to r7 ... ] * R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int tu 0 R7(config-if)#ipv *Mar 1 08:09:34.848: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R7(config-if)#ipv add 2005:17:17::7/64 R7(config-if)#rtun    tun sou fa 0/1 R7(config-if)#tun s des 180.40.7.66 R7(config-if)# *Mar 1 08:10:03.912: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R7(config-if)#ipv rip R7Rip en R7(config-if)#^Z R7# *Mar 1 08:10:13.616: %SYS-5-CONFIG_I: Configured from console by console R7#sh ipv route IPv6 Routing Table - 16 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 R 2000:4:4::/64 [120/3] via FE80::20A:8AFF:FEF0:D980, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:212:43FF:FEAC:6F60/128 [0/0] --More--   R7#pinm    2000:4:4:0:2D0:BAFF:FED3:BA40 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms R7#^x1 % Unknown command or computer name, or unable to find computer address R7# R7# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)#^Z R1#sh run *Mar 1 08:12:20.937: %SYS-5-CONFIG_I: Configured from console by console R1#sh run     int tu 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source 180.40.7.66 (Ethernet0/0), destination 180.40.7.1 Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled Tunnel TTL 255 Checksumming of packets disabled, fast tunneling enabled Last input 00:00:04, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 14 packets input, 1452 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 16 packets output, 2724 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R1#sh run int tun 0 Building configuration... Current configuration : 152 bytes ! interface Tunnel0 no ip address ipv6 address 2005:17:17::1/64 ipv6 rip R1Rip enable tunnel source Ethernet0/0 tunnel destination 180.40.7.1 end R1# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int s tu 0 Building configuration... Current configuration : 157 bytes ! interface Tunnel0 no ip address ipv6 address 2005:17:17::7/64 ipv6 rip R7Rip enable tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 end R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#iunt    int tu 0 R7(config-if)#tun mode ipv R7(config-if)#tun mode ipv6ip R7(config-if)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config yt ^ % Invalid input detected at '^' marker. R1#config yt  RACK13AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#^Z R7#config tsh run int tu 0^x1  *Mar 1 08:12:33.457: %SYS-5-CONFIG_I: Configured from console by console R7#^x1pin 2000:4:4:0:2D0:BAFF:FED3:BA40 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: .... RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0 R1(config-if)#tun mode ip R1(config-if)#tun mode ip % Ambiguous command: "tun mode ip" R1(config-if)#tun mode ipv R1(config-if)#tun mode ipv6ip R1(config-if)#^Z R1# RACK13AS>7 [Resuming connection 7 to r7 ... ] . Suc R7#pin 2000:4:4:0:2D0:BAFF:FED3:BA40 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms R7#SH IPV ROUTE IPv6 Routing Table - 16 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 R 2000:4:4::/64 [120/3] via FE80::20A:8AFF:FEF0:D980, Tunnel0 via FE80::B428:742, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 --More--   R7#^X1 % Unknown command or computer name, or unable to find computer address R7# R7# RACK13AS>1 [Resuming connection 1 to r1 ... ] * R1#SH RUN int tu 0 Building configuration... Current configuration : 172 bytes ! interface Tunnel0 no ip address ipv6 address 2005:17:17::1/64 ipv6 rip R1Rip enable tunnel source Ethernet0/0 tunnel destination 180.40.7.1 tunnel mode ipv6ip end R1# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int tu 9 0 Building configuration... Current configuration : 177 bytes ! interface Tunnel0 no ip address ipv6 address 2005:17:17::7/64 ipv6 rip R7Rip enable tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 tunnel mode ipv6ip end R7# R7# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipv pro e R2(config)#ipv prefix-list NoLoop den 2006:2:2::/128 R2(config)#ipv pri NoLoop per ::/0 le 128 ^ % Invalid input detected at '^' marker. R2(config)#ipv pri NoLoop per ::/0 le 128 NoLoop per ::/0 le 128 e NoLoop per ::/0 le 128 R2(config)#ipv router ospf 1 R2(config-rtr)#dis R2(config-rtr)#dist R2(config-rtr)#distr R2(config-rtr)#distribute-list pr R2(config-rtr)#distribute-list prefix-list NoLoop ? in out R2(config-rtr)#distribute-list prefix-list NoLoop out ? bgp Border Gateway Protocol (BGP) connected Connected Routes isis ISO IS-IS rip IPv6 Routing Information Protocol (RIPv6) static Static Routes R2(config-rtr)#distribute-list prefix-list NoLoop out conn R2(config-rtr)#distribute-list prefix-list NoLoop out connected ? R2(config-rtr)#distribute-list prefix-list NoLoop out connected R2(config-rtr)#ipv router rip R2Rip R2(config-rtr)#ipv router rip R2Ripdistribute-list prefix-list NoLoop out connected ^ % Invalid input detected at '^' marker. R2(config-rtr)#distribute-list prefix-list NoLoop out connected               out ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config-rtr)#distribute-list prefix-list NoLoop out s        % Incomplete command. R2(config-rtr)#distribute-list prefix-list NoLoop out R2(config-rtr)#int     do sh ip int briwe sh ip int briwe ^ % Invalid input detected at '^' marker. R2(config-rtr)#do sh ip int briwe   sh ip int bri % Incomplete command. R2(config-rtr)#do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 unassigned YES manual up up Serial1/0.1 unassigned YES unset up up Serial1/0.2 unassigned YES unset up up Serial1/1 unassigned YES unset up up Serial1/2 unassigned YES unset up up Serial1/3 unassigned YES unset administratively down down --More--  Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down R2(config-rtr)#int lo 0 R2(config-if)#ipv add 2006:2:2? X:X:X:X::X X:X:X:X::X/<0-128> R2(config-if)#ipv add 2006:2:2 2::/128 R2(config-if)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#ship   ipv        RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#ipv ospf      router ospf 1 R2(config-rtr)#distr R2(config-rtr)#distribute-list pr NoLoop ? in out R2(config-rtr)#distribute-list pr NoLoop in ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config-rtr)#distribute-list pr NoLoop in    out ? bgp Border Gateway Protocol (BGP) connected Connected Routes isis ISO IS-IS rip IPv6 Routing Information Protocol (RIPv6) static Static Routes R2(config-rtr)#distribute-list pr NoLoop out                               ipv router ospf 1add 2006:2:2::/128nt lo 0 do sh ip int brie weistribute-list prefix-list NoLoop out  out connected ipv router rip R2Rip  R2(config-rtr)#ipv router rip R2Ripospf 1 add 2006:2:2::/128nt lo 0 do sh ip int brie weistribute-list prefix-list NoLoop out ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config-rtr)#distribute-list prefix-list NoLoop out                                         RACK13AS>1 [Resuming connection 1 to r1 ... ] % Type "show ?" for a list of subcommands R1#sh ipb   v route IPv6 Routing Table - 15 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3:0:213:7FFF:FE12:A4E0/128 [120/3] via FE80::213:60FF:FEF0:FD40, Serial0/1 R 2000:4:4::/64 [120/2] via FE80::2D0:BAFF:FED3:BA40, Ethernet0/1 C 2005:0:102::/64 [0/0] via ::, Serial0/1 L 2005:0:102:0:20A:8AFF:FEF0:D980/128 [0/0] via ::, Serial0/1 C 2005:0:104::/64 [0/0] via ::, Ethernet0/1 L 2005:0:104:0:20A:8AFF:FEF0:D981/128 [0/0] via ::, Ethernet0/1 R 2005:0:237::/64 [120/2] via FE80::213:60FF:FEF0:FD40, Serial0/1 R 2005:0:237:0:213:7FFF:FE12:A4E0/128 [120/3] via FE80::213:60FF:FEF0:FD40, Serial0/1 R 2005:0:702::/64 [120/2] --More--   via FE80::213:60FF:FEF0:FD40, Serial0/1 R 2005:0:1203::/64 [120/2] via FE80::213:60FF:FEF0:FD40, Serial0/1 R 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [120/3] via FE80::213:60FF:FEF0:FD40, Serial0/1 C 2005:17:17::/64 [0/0] via ::, Tunnel0 L 2005:17:17::1/128 [0/0] via ::, Tunnel0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R1#^x   RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ipv route IPv6 Routing Table - 13 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3:0:213:7FFF:FE12:A4E0/128 [0/0] via ::, Loopback0 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/2 via FE80::213:60FF:FEF0:FD40, Serial1/0 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/2 via FE80::213:60FF:FEF0:FD40, Serial1/0 C 2005:0:237::/64 [0/0] via ::, Serial1/0 L 2005:0:237:0:213:7FFF:FE12:A4E0/128 [0/0] via ::, Serial1/0 O 2005:0:702::/64 [110/1562] via FE80::213:60FF:FEF0:FD40, Serial1/2 via FE80::212:43FF:FEAC:6F60, Serial1/0 --More--   via FE80::213:60FF:FEF0:FD40, Serial1/0 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203:0:213:60FF:FEF0:FD40/128 [110/781] via FE80::213:60FF:FEF0:FD40, Serial1/2 L 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [0/0] via ::, Serial1/2 OE2 2005:17:17::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/2 via FE80::213:60FF:FEF0:FD40, Serial1/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R3# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int lo 0 R1(config-if)#do sh ip   int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 180.40.7.66 YES manual up up Serial0/0 unassigned YES unset administratively down down Ethernet0/1 unassigned YES unset up up Serial0/1 unassigned YES manual up up Loopback0 unassigned YES unset up up Tunnel0 unassigned YES unset up up R1(config-if)#sh    do sh ip int briev int brie Ethernet0/0 [up/up] unassigned Serial0/0 [administratively down/down] unassigned Ethernet0/1 [up/up] FE80::20A:8AFF:FEF0:D981 2005:0:104:0:20A:8AFF:FEF0:D981 Serial0/1 [up/up] FE80::20A:8AFF:FEF0:D980 2005:0:102:0:20A:8AFF:FEF0:D980 Loopback0 [up/up] unassigned Tunnel0 [up/up] FE80::B428:742 2005:17:17::1 R1(config-if)#ipv add 2006:1:1::/128 R1(config-if)# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo1 R4(config-if)#ipd   v add 2006:3 4:34  4::/128 R4(config-if)#^Z R4# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#do sh ip   int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset up up Serial1/0 unassigned YES unset up up Serial1/1 unassigned YES unset administratively down down Serial1/2 unassigned YES unset up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--   R3(config)#int lo 1 R3(config-if)#ipv add 2006:3:3::/128 R3(config-if)# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#confity     t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip  router bgp 100 R7(config-router)#router R7(config-router)#router      bgp router   R7(config-router)#bgp router-id 7.7.7.7 R7(config-router)#ipv add R7(config-router)#ipv add       add ipv R7(config-router)#add ipv6 R7(config-router)#add ipv6   6 R7(config-router-af)#nei R7(config-router-af)#neighbor 2000:3:3:0:213:7FFF:FE12:A4E0 remot R7(config-router-af)#neighbor 2000:3:3:0:213:7FFF:FE12:A4E0 remote-as 100 R7(config-router-af)#do sh iop    ~ pv int brie FastEthernet0/0 [administratively down/down] unassigned BRI0/0 [administratively down/down] unassigned BRI0/0:1 [administratively down/down] unassigned BRI0/0:2 [administratively down/down] unassigned FastEthernet0/1 [up/up] unassigned Serial1/0 [up/up] unassigned Serial1/0.1 [up/up] FE80::212:43FF:FEAC:6F60 2005:0:237:0:212:43FF:FEAC:6F60 Serial1/0.2 [up/up] FE80::212:43FF:FEAC:6F60 2005:0:702:0:212:43FF:FEAC:6F60 Serial1/1 [administratively down/down] unassigned Serial1/2 [administratively down/down] unassigned Serial1/3 [administratively down/down] --More--   unassigned Serial1/4 [administratively down/down] unassigned Serial1/5 [administratively down/down] unassigned Serial1/6 [administratively down/down] unassigned Serial1/7 [administratively down/down] unassigned Tunnel0 [up/up] FE80::B428:701 2005:17:17::7 R7(config-router-af)#int lo 0 R7(config-if)#ipv add 2006:7:7::/128 R7(config-if)#ipv add 2006:7:7::/128nt lo 0 do sh ipv int brieneighbor 2000:3:3:0:213:7FFF:FE12:A4E0 remote-as 100add ipv6 bgp router-id 7.7.7.7router bgp 100  R7(config-router)#add ipv6 R7(config-router-af)#net 2006:7:7::/128 R7(config-router-af)#nei RACK13AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)#int lo 1 R1(config-if)#ipv add 2000:1:1::1/128 R1(config-if)#ipv rip R1Rip en R1(config-if)#exit R1(config)#do sh run | i ipv pre R1(config)#do sh run | i ipv pre6 pre ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 R1(config)#ip  ipv6 prefix-list Prob3 seq 6 den 2000:1:1::1/128 R1(config)# RACK13AS>7 [Resuming connection 7 to r7 ... ] % Incomplete command. R7(config-router-af)#nei 2000:1:1::1 remote 200 R7(config-router-af)#nei 2000:1:1::1 remote 200          u                 exit R7(config-router)#exit R7(config)#int lo 1 R7(config-if)#ip  v add 2000:7:7::7/128 R7(config-if)#router bgp 100 R7(config-router)#add ipv6 R7(config-router-af)#nei 2000:1:1::1 up R7(config-router-af)#nei 2000:1:1::1 update-source lo 1 R7(config-router-af)#nei 2000:1:1::1 eb R7(config-router-af)#nei 2000:1:1::1 ebgp-multihop 2 R7(config-router-af)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1(config)# R1(config)#router bgp 200 R1(config-router)#rotuer      bgp roter   uter 2 1.1.1.1 R1(config-router)#add ipv6 R1(config-router-af)#nei 2000:7:7::7 remote 100 R1(config-router-af)#nei 2000:7:7::7 remote 100          up lo 1 R1(config-router-af)#nei 2000:7:7::7 up lo 1       eb 2 R1(config-router-af)#net 2006:1; :1::/128 R1(config-router-af)#nei 2005:0:102:0:213:60FF:FEF0:FD40 remote 100 R1(config-router-af)#nei 2005:0:104:0:2D0:BAFF:FED3:BA40 remote 400 R1(config-router-af)#^Z R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-rtr)#do sh run | b rotuer bgp R2(config-rtr)#do sh run | b rotuer bgper bgp er bgp uer bgpter bgp R2(config-rtr)#do sh run | b router bgptuer bgputer bgp exit R2(config)#router bgp 234234 ^ % Invalid input detected at '^' marker. R2(config)#router bgp 234234  R2(config-router)#router bgp 23423nrouter bgp 23423orouter bgp 23423 router bgp 23423 R2(config)#router bgp 100 R2(config-router)#router-id brouter-id grouter-id prouter-id  router-id router-id 2.2.2.2 R2(config-router)#add ipv6 R2(config-router-af)#nei 2005:0:102:0:20A:8AFF:FEF0:D980 remote 100   200 R2(config-router-af)#nei 2000:3:3:0:213:7FFF:FE12:A4E0 remote 100 R2(config-router-af)#net 2006:2:2::/128 R2(config-router-af)#^Z R2# *Mar 1 08:39:15.415: %SYS-5-CONFIG_I: Configured from console by console R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#rotuer      uter bgp 100 R3(config-router)#bgp router 3.3.3.3 R3(config-router)#add ipv6 R3(config-router-af)#nei 2005:0:702:0:213:60FF:FEF0:FD40 % Incomplete command. R3(config-router-af)#nei 2005:0:702:0:213:60FF:FEF0:FD40 remote 100 R3(config-router-af)#nei 2005:0:237:0:212:43FF:FEAC:6F60 remote 100 R3(config-router-af)# *Mar 1 08:40:21.912: %BGP-5-ADJCHANGE: neighbor 2005:0:237:0:212:43FF:FEAC:6F60 Up R3(config-router-af)#nei 2005:0:237:0:212:43FF:FEAC:6F60 remote 100          up R3(config-router-af)#nei 2005:0:237:0:212:43FF:FEAC:6F60 update-source lo 0 R3(config-router-af)#nei 2005:0:237:0:212:43FF:FEAC:6F60 update-source lo 0remote 100 702:0:213:60FF:FEF0:FD40 remote 100          up lo 0 R3(config-router-af)# RACK13AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router r bgp 300 R4(config-router)#bgp routr 4   er 4.4.4.4 R4(config-router)#add ipv6 R4(config-router-af)#neri 2005:0:104:0:20A:8AFF:FEF0:D981 trem    remot 10  200neri 2005:0:104:0:20A:8AFF:FEF0:D981 remot 200  R4(config-router-af)#net 2006:4:4::/128 R4(config-router-af)#^Z R4# *Mar 1 08:44:10.785: %SYS-5-CONFIG_I: Configured from console by console R4#sh bgp sum BGP router identifier 4.4.4.4, local AS number 300 BGP table version is 1, main routing table version 1 Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2005:0:104:0:20A:8AFF:FEF0:D981 4 200 2 2 0 0 0 never Closing R4# *Mar 1 08:44:14.345: %BGP-3-NOTIFICATION: received from neighbor 2005:0:104:0:20A:8AFF:FEF0:D981 2/2 (peer in wrong AS) 2 bytes 012C R4#sh bgp sum BGP router identifier 4.4.4.4, local AS number 300 BGP table version is 1, main routing table version 1 1 network entries using 133 bytes of memory 1 path entries using 72 bytes of memory 1 BGP path attribute entries using 60 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 265 total bytes of memory BGP activity 1/0 prefixes, 1/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2005:0:104:0:20A:8AFF:FEF0:D981 4 200 2 2 0 0 0 never Idle R4#sh bgp sum BGP router identifier 4.4.4.4, local AS number 300 BGP table version is 1, main routing table version 1 1 network entries using 133 bytes of memory 1 path entries using 72 bytes of memory 1 BGP path attribute entries using 60 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 265 total bytes of memory BGP activity 1/0 prefixes, 1/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2005:0:104:0:20A:8AFF:FEF0:D981 4 200 2 2 0 0 0 never Idle R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 3, main routing table version 3 2 network entries using 266 bytes of memory 2 path entries using 144 bytes of memory 2 BGP path attribute entries using 120 bytes of memory 1 BGP AS-PATH entries using 24 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 554 total bytes of memory BGP activity 2/0 prefixes, 2/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:7:7::7 4 100 0 0 0 0 0 never Active 2005:0:102:0:213:60FF:FEF0:FD40 4 100 7 7 3 0 0 00:02:41 1 2005:0:104:0:2D0:BAFF:FED3:BA40 4 400 2 2 0 0 0 never Idle R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#rouetr   ter bgp 200 R1(config-router)#add *Mar 1 08:43:47.562: %BGP-3-NOTIFICATION: sent to neighbor 2005:0:104:0:2D0:BAFF:FED3:BA40 2/2 (peer in wrong AS) 2 bytes 012C R1(config-router)#add ipv FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 012C 00B4 0404 0404 1002 0601 0400 0200 0102 0280 0002 0202 00 R1(config-router)#add ipv6 R1(config-router-af)#add ipv6router bgp 200nei 2005:0:104:0:2D0:BAFF:FED3:BA40 remote 400   300 R1(config-router-af)#nei 2005:0:104:0:2D0:BAFF:FED3:BA40 remote 300add ipv6 router bgp 200nei 2005:0:104:0:2D0:BAFF:FED3:BA40 remote 400nnei 2005:0:104:0:2D0:BAFF:FED3:BA40 remote 400onei 2005:0:104:0:2D0:BAFF:FED3:BA40 remote 400 nei 2005:0:104:0:2D0:BAFF:FED3:BA40 remote 400 R1(config-router-af)#^Z R1#swh *Mar 1 08:44:04.533: %SYS-5-CONFIG_I: Configured from console by console R1#swh     h   sh run | b router bgp router bgp 200 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes neighbor 2000:7:7::7 remote-as 100 neighbor 2000:7:7::7 ebgp-multihop 2 neighbor 2000:7:7::7 update-source Loopback1 no neighbor 2000:7:7::7 activate neighbor 2005:0:102:0:213:60FF:FEF0:FD40 remote-as 100 no neighbor 2005:0:102:0:213:60FF:FEF0:FD40 activate neighbor 2005:0:104:0:2D0:BAFF:FED3:BA40 remote-as 300 no neighbor 2005:0:104:0:2D0:BAFF:FED3:BA40 activate no auto-summary ! address-family ipv6 neighbor 2000:7:7::7 activate neighbor 2005:0:102:0:213:60FF:FEF0:FD40 activate neighbor 2005:0:104:0:2D0:BAFF:FED3:BA40 activate network 2006:1:1::/128 exit-address-family ! no ip http server ip classless --More--  ! ! ipv6 router rip R1Rip distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 6 deny 2000:1:1::1/128 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! --More-- *Mar 1 08:44:37.527: %BGP-5-ADJCHANGE: neighbor 2005:0:104:0:2D0:BAFF:FED3:BA40 Up --More--   R1#sh run | b router bgpconfig t sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 4, main routing table version 4 3 network entries using 399 bytes of memory 3 path entries using 216 bytes of memory 3 BGP path attribute entries using 180 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 843 total bytes of memory BGP activity 3/0 prefixes, 3/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:7:7::7 4 100 0 0 0 0 0 never Active 2005:0:102:0:213:60FF:FEF0:FD40 4 100 9 10 4 0 0 00:04:20 1 2005:0:104:0:2D0:BAFF:FED3:BA40 4 300 9 10 4 0 0 00:00:25 1 R1#sh    sh ip        RACK13AS>7 [Resuming connection 7 to r7 ... ] *Mar R7(config-router-af)#int lo 1 R7(config-if)#ipv rip R7Rip en R7(config-if)# *Mar 1 08:44:30.728: %BGP-5-ADJCHANGE: neighbor 2000:1:1::1 Up R7(config-if)# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh bgp suym\   m BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 5, main routing table version 5 4 network entries using 532 bytes of memory 4 path entries using 288 bytes of memory 3 BGP path attribute entries using 180 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1048 total bytes of memory BGP activity 4/0 prefixes, 4/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:7:7::7 4 100 5 7 4 0 0 00:00:14 1 2005:0:102:0:213:60FF:FEF0:FD40 4 100 10 12 5 0 0 00:05:05 1 2005:0:104:0:2D0:BAFF:FED3:BA40 4 300 10 12 5 0 0 00:01:11 1 R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 R2#sh bgp BGP table version is 4, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-router-af)#nei 2005:0:702:0:213:60FF:FEF0:FD40 up lo 0237:0:212:43FF:FEAC:6F60 update-source lo 0remote 100 update-source lo 0702:0:213:60FF:FEF0:FD40 up lo 0  net 2006:3:3//  ::/128 R3(config-router-af)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh bgpconfig tsh bgp  BGP table version is 4, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2#sh bgp BGP table version is 4, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2#sh bgp BGP table version is 5, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#do sh bgp BGP table version is 5, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2000:1:1::1 0 0 200 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2000:1:1::1 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-router-af)#do sh ru  bgp BGP table version is 6, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i2006:1:1::/128 2000:1:1::1 0 100 0 200 i *>i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 i *>i2006:2:2::/128 2005:0:702:0:213:60FF:FEF0:FD40 0 100 0 i *> 2006:3:3::/128 :: 0 32768 i * i2006:4:4::/128 2000:1:1::1 0 100 0 200 300 i *>i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 300 i *>i2006:7:7::/128 2005:0:237:0:212:43FF:FEAC:6F60 0 100 0 i R3(config-router-af)#do sh bgpnet 2006:3:3::/128i 2005:0:702:0:213:60FF:FEF0:FD40 up lo 0       ro R3(config-router-af)#nei 2005:0:702:0:213:60FF:FEF0:FD40 route-r R3(config-router-af)#$702:0:213:60FF:FEF0:FD40 route-reflector-client R3(config-router-af)#$702:0:213:60FF:FEF0:FD40 route-reflector-client do sh bgp  *Mar 1 08:46:12.547: %BGP-5-ADJCHANGE: neighbor 2005:0:702:0:213:60FF:FEF0:FD40 Down RR client config change R3(config-router-af)#do sh bgpnet 2006:3:3::/128i 2005:0:702:0:213:60FF:FEF0:FD40 up lo 0237:0:212:43FF:FEAC:6F60 update-source lo 0                  rou R3(config-router-af)#nei 2005:0:237:0:212:43FF:FEAC:6F60 route-r R3(config-router-af)#$237:0:212:43FF:FEAC:6F60 route-reflector-client R3(config-router-af)# *Mar 1 08:46:23.465: %BGP-5-ADJCHANGE: neighbor 2005:0:237:0:212:43FF:FEAC:6F60 Down RR client config change R3(config-router-af)#^Z R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] * R2#sh ip    bgp BGP table version is 6, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2#sh bgp BGP table version is 6, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2#sh bgp BGP table version is 6, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2#sh bgp BGP table version is 6, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2#sh bgp BGP table version is 7, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2# *Mar 1 08:46:41.578: %BGP-5-ADJCHANGE: neighbor 2000:3:3:0:213:7FFF:FE12:A4E0 Up R2#sh bgp BGP table version is 7, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2#sh bgp BGP table version is 7, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2#sh bgp BGP table version is 7, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2#sh bgp BGP table version is 7, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i R2# RACK13AS>7 [Resuming connection 7 to r7 ... ] *Ma R7(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh bgp     run | b router bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes neighbor 2005:0:237:0:212:43FF:FEAC:6F60 remote-as 100 neighbor 2005:0:237:0:212:43FF:FEAC:6F60 update-source Loopback0 no neighbor 2005:0:237:0:212:43FF:FEAC:6F60 activate neighbor 2005:0:702:0:213:60FF:FEF0:FD40 remote-as 100 neighbor 2005:0:702:0:213:60FF:FEF0:FD40 update-source Loopback0 no neighbor 2005:0:702:0:213:60FF:FEF0:FD40 activate no auto-summary ! address-family ipv6 neighbor 2005:0:237:0:212:43FF:FEAC:6F60 activate neighbor 2005:0:237:0:212:43FF:FEAC:6F60 route-reflector-client neighbor 2005:0:702:0:213:60FF:FEF0:FD40 activate neighbor 2005:0:702:0:213:60FF:FEF0:FD40 route-reflector-client network 2006:3:3::/128 exit-address-family ! ip classless ! no ip http server --More--   R3#sh    sh bgp BGP table version is 14, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i2006:1:1::/128 2000:1:1::1 0 100 0 200 i *>i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 i *>i2006:2:2::/128 2005:0:702:0:213:60FF:FEF0:FD40 0 100 0 i *> 2006:3:3::/128 :: 0 32768 i * i2006:4:4::/128 2000:1:1::1 0 100 0 200 300 i *>i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 300 i *>i2006:7:7::/128 2005:0:237:0:212:43FF:FEAC:6F60 0 100 0 i R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh bgp BGP table version is 8, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 200 300 i *>i2006:7:7::/128 2005:0:237:0:212:43FF:FEAC:6F60 0 100 0 i R2#sh ipv route IPv6 Routing Table - 21 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 R 2000:7:7::7/128 [120/3] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 --More--   via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/2 O 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 R 2005:17:17::/64 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 B 2006:1:1::/128 [20/0] via FE80::20A:8AFF:FEF0:D980, Serial1/1 LC 2006:2:2::/128 [0/0] via ::, Loopback0 B 2006:3:3::/128 [200/0] via 2000:3:3:0:213:7FFF:FE12:A4E0 B 2006:4:4::/128 [20/0] via FE80::20A:8AFF:FEF0:D980, Serial1/1 B 2006:7:7::/128 [200/0] via 2005:0:237:0:212:43FF:FEAC:6F60 --More--  L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#^Z R2# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#^Z R7#sh bgp BGP table version is 8, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 i *> 2000:1:1::1 0 0 200 i *>i2006:2:2::/128 2005:0:702:0:213:60FF:FEF0:FD40 0 100 0 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i * i2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 300 i *> 2000:1:1::1 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7# *Mar 1 08:48:29.367: %SYS-5-CONFIG_I: Configured from console by console R7#sh ip  v route IPv6 Routing Table - 23 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:1:1::1/128 [120/2] via FE80::B428:742, Tunnel0 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 R 2000:4:4::/64 [120/3] via FE80::B428:742, Tunnel0 LC 2000:7:7::7/128 [0/0] via ::, Loopback1 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] --More--   via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 OI 2005:0:1203:0:213:60FF:FEF0:FD40/128 [110/781] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OI 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:17:17::/64 [0/0] via ::, Tunnel0 L 2005:17:17::7/128 [0/0] via ::, Tunnel0 B 2006:1:1::/128 [20/0] via 2000:1:1::1 B 2006:2:2::/128 [200/0] via 2005:0:702:0:213:60FF:FEF0:FD40 B 2006:3:3::/128 [200/0] via 2000:3:3:0:213:7FFF:FE12:A4E0 B 2006:4:4::/128 [20/0] --More--   R7#sh bgp BGP table version is 8, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i2006:1:1::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 i *> 2000:1:1::1 0 0 200 i *>i2006:2:2::/128 2005:0:702:0:213:60FF:FEF0:FD40 0 100 0 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i * i2006:4:4::/128 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 300 i *> 2000:1:1::1 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7# RACK13AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#sh vf  bgp BGP table version is 6, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:104:0:20A:8AFF:FEF0:D981 0 0 200 i *> 2006:2:2::/128 2005:0:104:0:20A:8AFF:FEF0:D981 0 200 100 i *> 2006:3:3::/128 2005:0:104:0:20A:8AFF:FEF0:D981 0 200 100 i *> 2006:4:4::/128 :: 0 32768 i *> 2006:7:7::/128 2005:0:104:0:20A:8AFF:FEF0:D981 0 200 100 i R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int u 0 ^ % Invalid input detected at '^' marker. R1(config)#int u tu 0 R1(config-if)#tun destntun destotun dest tun dest R1(config-if)# *Mar 1 08:54:24.738: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#do sh tu  run int tu 0 Building configuration... Current configuration : 141 bytes ! interface Tunnel0 no ip address ipv6 address 2005:17:17::1/64 ipv6 rip R1Rip enable tunnel source Ethernet0/0 tunnel mode ipv6ip end R1(config-if)#no ipv6 address 2005:17:17::1/64 R1(config-if)# *Mar 1 08:56:35.797: %BGP-5-ADJCHANGE: neighbor 2000:7:7::7 Down BGP Notification sent R1(config-if)# *Mar 1 08:56:35.797: %BGP-3-NOTIFICATION: sent to neighbor 2000:7:7::7 4/0 (hold time expired) 0 bytes R1(config-if)#ipv add 2002:b428:742::1/128 R1(config-if)#tun mod ipv R1(config-if)#tun mod ipv6ip 6 R1(config-if)#tun mod ipv6ip 6to4 R1(config-if)# *Mar 1 08:57:46.541: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-if)#exit R1(config)#ipv     ipv route R1(config)#ipv route 2002::/16 tun 0 R1(config)# RACK13AS>7 [Resuming connection 7 to r7 ... ] *M R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int tu 0 R7(config-if)#do sh run int tu 0 Building configuration... Current configuration : 177 bytes ! interface Tunnel0 no ip address ipv6 address 2005:17:17::7/64 ipv6 rip R7Rip enable tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 tunnel mode ipv6ip end R7(config-if)#no ipv6 address 2005:17:17::1/64 R7(config-if)#no tunnel destination 180.40.7.66 R7(config-if)#ipv add 2002 *Mar 1 08:57:34.965: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R7(config-if)#ipv add 2002:b428:701::1/128 R7(config-if)#tun mode ipv R7(config-if)#tun mode ipv6ip 6 R7(config-if)#tun mode ipv6ip 6to4 R7(config-if)#exit R7(config)# *Mar 1 08:57:53.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R7(config)#ipv tu  router     \  e 2002::/16 tun 0 R7(config)#ping 2002dping 2002oping 2002 ping 2002ping 2002:b428:742::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:742::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/89/97 ms R7(config)#do sh ipv route IPv6 Routing Table - 24 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 LC 2000:7:7::7/128 [0/0] via ::, Loopback1 S 2002::/16 [1/0] via ::, Tunnel0 LC 2002:B428:701::1/128 [0/0] via ::, Tunnel0 OE2 2002:B428:742::1/128 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:212:43FF:FEAC:6F60/128 [0/0] --More--   via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 OI 2005:0:1203:0:213:60FF:FEF0:FD40/128 [110/781] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OI 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:17:17::/64 [0/0] via ::, Tunnel0 L 2005:17:17::7/128 [0/0] via ::, Tunnel0 B 2006:1:1::/128 [200/0] via 2005:0:102:0:20A:8AFF:FEF0:D980 B 2006:2:2::/128 [200/0] via 2005:0:702:0:213:60FF:FEF0:FD40 B 2006:3:3::/128 [200/0] --More--   via 2000:3:3:0:213:7FFF:FE12:A4E0 B 2006:4:4::/128 [200/0] via 2005:0:102:0:20A:8AFF:FEF0:D980 LC 2006:7:7::/128 [0/0] via ::, Loopback0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7(config)#sh    do sh vg  bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 10, main routing table version 10 5 network entries using 665 bytes of memory 5 path entries using 360 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 1 BGP rrinfo entries using 24 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1337 total bytes of memory BGP activity 6/1 prefixes, 8/3 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:1:1::1 4 200 19 20 0 0 0 00:03:46 Active 2000:3:3:0:213:7FFF:FE12:A4E0 4 100 31 33 10 0 0 00:12:12 4 R7(config)#ipv 2000:1:1::1 2002:b428:742::1 ^ % Invalid input detected at '^' marker. R7(config)#ipv 2000:1:1::1 2002:b428:742::1r2000:1:1::1 2002:b428:742::1o2000:1:1::1 2002:b428:742::1u2000:1:1::1 2002:b428:742::1t2000:1:1::1 2002:b428:742::1e2000:1:1::1 2002:b428:742::1 2000:1:1::1 2002:b428:742::1 ^ % Invalid input detected at '^' marker. R7(config)#ipv route 2000:1:1::1 2002:b428:742::1/ 2002:b428:742::11 2002:b428:742::12 2002:b428:742::18 2002:b428:742::1 R7(config)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1(config)#ipv route 2000:7:7::7  /128 2002:b428:7091  1::1 R1(config)#ping 2000:7:76 ::7 ^ % Invalid input detected at '^' marker. R1(config)#ping 2000:7:7::7dping 2000:7:7::7oping 2000:7:7::7 ping 2000:7:7::7 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:7:7::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/47/56 ms R1(config)#^Z R1#sh *Mar 1 09:02:28.743: %SYS-5-CONFIG_I: Configured from console by console R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 10, main routing table version 10 5 network entries using 665 bytes of memory 5 path entries using 360 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1313 total bytes of memory BGP activity 5/0 prefixes, 10/5 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:7:7::7 4 100 16 23 0 0 0 00:05:56 Active 2005:0:102:0:213:60FF:FEF0:FD40 4 100 30 31 10 0 0 00:21:49 3 2005:0:104:0:2D0:BAFF:FED3:BA40 4 300 26 32 10 0 0 00:17:55 1 R1# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7(config)#do pin 2000:1; :1::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:1:1::1, timeout is 2 seconds: UUUUU Success rate is 0 percent (0/5) R7(config)#do pin 2000:1:1::1ipv route 2000:1:1::1/128 2002:b428:742::1q ^Z R7#sh *Mar 1 09:02:44.152: %SYS-5-CONFIG_I: Configured from console by console R7#sh ipb rout ^ % Invalid input detected at '^' marker. R7#sh ipb routb rout v rout IPv6 Routing Table - 25 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S 2000:1:1::1/128 [1/0] via 2002:B428:742::1 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 LC 2000:7:7::7/128 [0/0] via ::, Loopback1 S 2002::/16 [1/0] via ::, Tunnel0 LC 2002:B428:701::1/128 [0/0] via ::, Tunnel0 OE2 2002:B428:742::1/128 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 C 2005:0:237::/64 [0/0] --More--   via ::, Serial1/0.1 L 2005:0:237:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 OI 2005:0:1203:0:213:60FF:FEF0:FD40/128 [110/781] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OI 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:17:17::/64 [0/0] via ::, Tunnel0 L 2005:17:17::7/128 [0/0] via ::, Tunnel0 B 2006:1:1::/128 [200/0] via 2005:0:102:0:20A:8AFF:FEF0:D980 B 2006:2:2::/128 [200/0] --More--   R7#sh ipv rout s % Ambiguous command: "sh ipv rout s" R7#sh ipv rout sta IPv6 Routing Table - 25 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S 2000:1:1::1/128 [1/0] via 2002:B428:742::1 S 2002::/16 [1/0] via ::, Tunnel0 R7#pin 2002:B428:742::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:742::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/88/89 ms R7#ping 2000:1:1::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:1:1::1, timeout is 2 seconds: UUUUU Success rate is 0 percent (0/5) R7#deb ipv icmp ICMP packet debugging is on R7#deb ipv icmp ping 2000:1:1::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:1:1::1, timeout is 2 seconds: UUUUU Success rate is 0 percent (0/5) R7# *Mar 1 09:04:09.084: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:04:09.152: ICMPv6: Received ICMPv6 packet from 2005:0:702:0:213:60FF:FEF0:FD40, type 1 *Mar 1 09:04:09.156: ICMPv6: Received ICMP unreachable code 0 from 2005:0:702:0:213:60FF:FEF0:FD40 *Mar 1 09:04:09.156: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:04:09.228: ICMPv6: Received ICMPv6 packet from 2005:0:702:0:213:60FF:FEF0:FD40, type 1 *Mar 1 09:04:09.228: ICMPv6: Received ICMP unreachable code 0 from 2005:0:702:0:213:60FF:FEF0:FD40 *Mar 1 09:04:09.228: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:04:09.300: ICMPv6: Received ICMPv6 packet from 2005:0:702:0:213:60FF:FEF0:FD40, type 1 *Mar 1 09:04:09.300: ICMPv6: Received ICMP unreachable code 0 from 2005:0:702:0:213:60FF:FEF0:FD40 *Mar 1 09:04:09.300: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:04:09.372: ICMPv6: Received ICMPv6 packet from 2005:0:702:0:213:60FF:FEF0:FD40, type 1 *Mar 1 09:04:09.372: ICMPv6: R7#Received ICMP unreachable code 0 from 2005:0:702:0:213:60FF:FEF0:FD40 *Mar 1 09:04:09.372: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:04:09.444: ICMPv6: Received ICMPv6 packet from 2005:0:702:0:213:60FF:FEF0:FD40, type 1 *Mar 1 09:04:09.444: ICMPv6: Received ICMP unreachable code 0 from 2005:0:702:0:213:60FF:FEF0:FD40 R7#sh ipv route 210   2000: % Incomplete command. R7#sh ipv route 2000:: % Route not found R7#sh ipv route 2000::1  1:1::1 IPv6 Routing Table - 25 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S 2000:1:1::1/128 [1/0] via 2002:B428:742::1 R7#sh ipv route 2002:     2002:B428:742::1 IPv6 Routing Table - 25 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OE2 2002:B428:742::1/128 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 R7# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv pre R1(config)#ipv prefix-list                 do sh ipv pre ipv6 prefix-list Prob3: 3 entries seq 5 deny 2000:4:4::/64 seq 6 deny 2000:1:1::1/128 seq 10 permit ::/0 le 128 R1(config)#ipv pre R1(config)#ipv prefix-list Prob3 den R1(config)#ipv prefix-list Prob3 deny 2002:B428:742::1/128y 7deny 2002:B428:742::1/128 deny 2002:B428:742::1/128 ^ % Invalid input detected at '^' marker. R1(config)#ipv prefix-list Prob3 7 deny 2002:B428:742::1/128 deny 2002:B428:742::1/128 deny 2002:B428:742::1/128 sdeny 2002:B428:742::1/128edeny 2002:B428:742::1/128qdeny 2002:B428:742::1/128 deny 2002:B428:742::1/1287deny 2002:B428:742::1/128 ^ % Invalid input detected at '^' marker. R1(config)#ipv prefix-list Prob3 seq 7deny 2002:B428:742::1/128 deny 2002:B428:742::1/128 R1(config)#ipv prefix-list Prob3 seq 7 deny 2002:B428:742::1/128deny 2002:B428:742::1/128 7 deny 2002:B428:742::1/128 do sh ipv pre  ipv6 prefix-list Prob3: 4 entries seq 5 deny 2000:4:4::/64 seq 6 deny 2000:1:1::1/128 seq 7 deny 2002:B428:742::1/128 seq 10 permit ::/0 le 128 R1(config)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh ipv route IPv6 Routing Table - 20 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 R 2002:B428:742::1/128 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::20A:8AFF:FEF0:D980, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 --More--   R2#clea ipb v rip R2#clea ipv ripsh ipv route IPv6 Routing Table - 18 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] --More--   via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/2 O 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 B 2006:1:1::/128 [20/0] via FE80::20A:8AFF:FEF0:D980, Serial1/1 LC 2006:2:2::/128 [0/0] via ::, Loopback0 B 2006:3:3::/128 [200/0] via 2000:3:3:0:213:7FFF:FE12:A4E0 B 2006:4:4::/128 [20/0] via FE80::20A:8AFF:FEF0:D980, Serial1/1 B 2006:7:7::/128 [200/0] via 2005:0:237:0:212:43FF:FEAC:6F60 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#clea ipb v route * R2#clea ipv route *sh ipv route  IPv6 Routing Table - 18 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] --More--   via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/2 O 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 B 2006:1:1::/128 [20/0] via FE80::20A:8AFF:FEF0:D980, Serial1/1 LC 2006:2:2::/128 [0/0] via ::, Loopback0 B 2006:3:3::/128 [200/0] via 2000:3:3:0:213:7FFF:FE12:A4E0 B 2006:4:4::/128 [20/0] via FE80::20A:8AFF:FEF0:D980, Serial1/1 B 2006:7:7::/128 [200/0] via 2005:0:237:0:212:43FF:FEAC:6F60 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#sh ipv route IPv6 Routing Table - 18 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:213:60FF:FEF0:FD40/128 [0/0] --More--   via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203:0:213:60FF:FEF0:FD40/128 [0/0] via ::, Serial1/2 O 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/2 B 2006:1:1::/128 [20/0] via FE80::20A:8AFF:FEF0:D980, Serial1/1 LC 2006:2:2::/128 [0/0] via ::, Loopback0 B 2006:3:3::/128 [200/0] via 2000:3:3:0:213:7FFF:FE12:A4E0 B 2006:4:4::/128 [20/0] via FE80::20A:8AFF:FEF0:D980, Serial1/1 B 2006:7:7::/128 [200/0] via 2005:0:237:0:212:43FF:FEAC:6F60 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#sh ipv rip data RIP process "R2Rip", local RIB 2005:0:102::/64, metric 2 Serial1/1/FE80::20A:8AFF:FEF0:D980, expires in 178 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::20A:8AFF:FEF0:D980, expires in 178 secs R2# RACK13AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#sh ipv route 2002:B428:742::10:1:1::1 :  ping 2000:1:1::1 deb ipv icmp ping 2000:1:1::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:1:1::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R7# *Mar 1 09:07:28.046: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:07:28.050: ICMPv6: Received ICMPv6 packet from 2000:1:1::1, type 129 *Mar 1 09:07:28.050: ICMPv6: Received echo reply from 2000:1:1::1 *Mar 1 09:07:28.050: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:07:28.058: ICMPv6: Received ICMPv6 packet from 2000:1:1::1, type 129 *Mar 1 09:07:28.058: ICMPv6: Received echo reply from 2000:1:1::1 *Mar 1 09:07:28.058: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:07:28.062: ICMPv6: Received ICMPv6 packet from 2000:1:1::1, type 129 *Mar 1 09:07:28.062: ICMPv6: Received echo reply from 2000:1:1::1 R7# *Mar 1 09:07:28.062: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:07:28.070: ICMPv6: Received ICMPv6 packet from 2000:1:1::1, type 129 *Mar 1 09:07:28.070: ICMPv6: Received echo reply from 2000:1:1::1 *Mar 1 09:07:28.070: ICMPv6: Sending echo request to 2000:1:1::1 *Mar 1 09:07:28.074: ICMPv6: Received ICMPv6 packet from 2000:1:1::1, type 129 *Mar 1 09:07:28.074: ICMPv6: Received echo reply from 2000:1:1::1 R7#u all All possible debugging has been turned off R7#sh bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 12, main routing table version 12 5 network entries using 665 bytes of memory 7 path entries using 504 bytes of memory 6 BGP path attribute entries using 360 bytes of memory 1 BGP rrinfo entries using 24 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1601 total bytes of memory BGP activity 6/1 prefixes, 10/3 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:1:1::1 4 200 27 26 12 0 0 00:00:22 2 2000:3:3:0:213:7FFF:FE12:A4E0 4 100 39 43 12 0 0 00:20:30 4 R7# R7# R7# R7#sh ipv route IPv6 Routing Table - 24 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S 2000:1:1::1/128 [1/0] via 2002:B428:742::1 OI 2000:3:3:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 LC 2000:7:7::7/128 [0/0] via ::, Loopback1 S 2002::/16 [1/0] via ::, Tunnel0 LC 2002:B428:701::1/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::213:60FF:FEF0:FD40, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237:0:212:43FF:FEAC:6F60/128 [0/0] --More--   via ::, Serial1/0.1 O 2005:0:237:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702:0:212:43FF:FEAC:6F60/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 OI 2005:0:1203:0:213:60FF:FEF0:FD40/128 [110/781] via FE80::213:60FF:FEF0:FD40, Serial1/0.2 OI 2005:0:1203:0:213:7FFF:FE12:A4E0/128 [110/781] via FE80::213:7FFF:FE12:A4E0, Serial1/0.1 C 2005:17:17::/64 [0/0] via ::, Tunnel0 L 2005:17:17::7/128 [0/0] via ::, Tunnel0 B 2006:1:1::/128 [20/0] via 2000:1:1::1 B 2006:2:2::/128 [200/0] via 2005:0:702:0:213:60FF:FEF0:FD40 B 2006:3:3::/128 [200/0] --More--   R7# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router bgp 300 R4(config-router)#add   i add ipv6 R4(config-router-af)#net 2000:4:4::/64 R4(config-router-af)# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#sh bgp BGP table version is 12, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2000:1:1::1 0 0 200 i * i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 i *>i2006:2:2::/128 2005:0:702:0:213:60FF:FEF0:FD40 0 100 0 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2000:1:1::1 0 200 300 i * i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7#sh bgp BGP table version is 12, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2000:1:1::1 0 0 200 i * i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 i *>i2006:2:2::/128 2005:0:702:0:213:60FF:FEF0:FD40 0 100 0 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2000:1:1::1 0 200 300 i * i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7#sh bgp BGP table version is 13, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i2000:4:4::/64 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 300 i *> 2000:1:1::1 0 200 300 i *> 2006:1:1::/128 2000:1:1::1 0 0 200 i * i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 i *>i2006:2:2::/128 2005:0:702:0:213:60FF:FEF0:FD40 0 100 0 i *>i2006:3:3::/128 2000:3:3:0:213:7FFF:FE12:A4E0 0 100 0 i *> 2006:4:4::/128 2000:1:1::1 0 200 300 i * i 2005:0:102:0:20A:8AFF:FEF0:D980 0 100 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7#p 2000:4:4:0:2D0:BAFF:FED3:BA40 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7#ping ipv Target IPv6 address: 2000:4:4:0:2D0:BAFF:FED3:BA40 Repeat count [5]: Datagram size [100]: Timeout in seconds [2]: Extended commands? [no]: y UDP protocol? [no]: Precedence [0]: DSCP [0]: Include extension headers? [no]: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config-router-af)#exit R4(config-router)#exit R4(config)#ipv route ::/0 fa 0/0 R4(config)# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#y2000:4:4:0:2D0:BAFF:FED3:BA40ping ipv  2000:4:4:0:2D0:BAFF:FED3:BA40 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7# RACK13AS>1 [Resuming connection 1 to r1 ... ] * R1(config)#^Z R1#sh *Mar 1 09:12:56.352: %SYS-5-CONFIG_I: Configured from console by console R1#sh ipv route IPv6 Routing Table - 22 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 LC 2000:1:1::1/128 [0/0] via ::, Loopback1 R 2000:3:3:0:213:7FFF:FE12:A4E0/128 [120/3] via FE80::213:60FF:FEF0:FD40, Serial0/1 B 2000:4:4::/64 [20/0] via FE80::2D0:BAFF:FED3:BA40, Ethernet0/1 S 2000:7:7::7/128 [1/0] via 2002:B428:701::1 S 2002::/16 [1/0] via ::, Tunnel0 LC 2002:B428:742::1/128 [0/0] via ::, Tunnel0 C 2005:0:102::/64 [0/0] via ::, Serial0/1 L 2005:0:102:0:20A:8AFF:FEF0:D980/128 [0/0] via ::, Serial0/1 C 2005:0:104::/64 [0/0] --More--   R1# RACK13AS> [Resuming connection 1 to r1 ... ] R1# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config)#^Z R4# *Mar 1 09:14:24.049: %SYS-5-CONFIG_I: Configured from console by console R4#deb ipv icmp ICMP packet debugging is on R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#logg % Incomplete command. R4(config)#logg buff R4(config)#^Z R4# RACK13AS>7 [Resuming connection 7 to r7 ... ] p 2000:4:4:0:2D0:BAFF:FED3:BA40 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: RACK13AS>4 [Resuming connection 4 to r4 ... ] *Mar 1 09:14:38.025: %SYS-5-CONFIG_I: Configured fro R4# *Mar 1 09:14:40.953: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:14:40.953: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:40.953: ICMPv6: Sending echo reply to 2002:B428:701::1 R4# *Mar 1 09:14:42.953: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:14:42.953: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:42.957: ICMPv6: Sending echo reply to 2002:B428:701::1 R4# *Mar 1 09:14:44.957: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:14:44.957: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:44.957: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:14:45.953: ICMPv6: Received ICMPv6 packet from FE80::20A:8AFF:FEF0:D981, type 135 R4# *Mar 1 09:14:46.961: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:14:46.961: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:46.961: ICMPv6: Sending echo reply to 2002:B428:701::1 R4# *Mar 1 09:14:48.961: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:14:48.961: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:48.961: ICMPv6: Sending echo reply to 2002:B428:701::1 R4# *Mar 1 09:14:50.953: ICMPv6: Received ICMPv6 packet from FE80::20A:8AFF:FEF0:D981, type 136 R4# RACK13AS>7 [Resuming connection 7 to r7 ... ] .. R7#p 2000:4:4:0:2D0:BAFF:FED3:BA40 ? data specify data pattern df-bit enable do not fragment bit in IP header repeat specify repeat count size specify datagram size source specify source address or name timeout specify timeout interval validate validate reply data R7#ping 2000:4:4:0:2D0:BAFF:FED3:BA40 sou ? A.B.C.D Source address Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R7#ping 2000:4:4:0:2D0:BAFF:FED3:BA40 sou lo 0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7#ping 2000:4:4:0:2D0:BAFF:FED3:BA40 sou lo 0 1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4:0:2D0:BAFF:FED3:BA40, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7# RACK13AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#sh logg Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 82 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 50 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 38 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 09:14:38.025: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 09:14:40.953: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:14:40.953: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:40.953: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:14:42.953: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:14:42.953: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:42.957: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:14:44.957: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:14:44.957: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:44.957: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:14:45.953: ICMPv6: Received ICMPv6 packet from FE80::20A:8AFF:FEF0:D981, type 135 *Mar 1 09:14:46.961: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:14:46.961: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:46.961: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:14:48.961: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 --More--  *Mar 1 09:14:48.961: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:14:48.961: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:14:50.953: ICMPv6: Received ICMPv6 packet from FE80::20A:8AFF:FEF0:D981, type 136 *Mar 1 09:15:27.613: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:15:27.613: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:15:27.613: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:15:29.613: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:15:29.617: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:15:29.617: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:15:31.613: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:15:31.613: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:15:31.617: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:15:32.609: ICMPv6: Received ICMPv6 packet from FE80::20A:8AFF:FEF0:D981, type 135 *Mar 1 09:15:33.617: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:15:33.617: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:15:33.617: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:15:35.621: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 --More--  *Mar 1 09:15:35.621: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:15:35.621: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:15:37.609: ICMPv6: Received ICMPv6 packet from FE80::20A:8AFF:FEF0:D981, type 136 *Mar 1 09:15:39.413: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:15:39.413: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:15:39.413: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:15:41.409: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:15:41.409: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:15:41.413: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:15:43.413: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:15:43.413: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:15:43.413: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:15:45.417: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:15:45.417: ICMPv6: Received echo request from 2002:B428:701::1 *Mar 1 09:15:45.417: ICMPv6: Sending echo reply to 2002:B428:701::1 *Mar 1 09:15:47.417: ICMPv6: Received ICMPv6 packet from 2002:B428:701::1, type 128 *Mar 1 09:15:47.417: ICMPv6: Received echo request from 2002:B428:701::1 --More--  *Mar 1 09:15:47.417: ICMPv6: Sending echo reply to 2002:B428:701::1 R4#    sh ipv route IPv6 Routing Table - 21 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S ::/0 [1/0] via ::, FastEthernet0/0 R 2000:1:1::1/128 [120/2] via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 R 2000:3:3:0:213:7FFF:FE12:A4E0/128 [120/4] via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4:0:2D0:BAFF:FED3:BA40/128 [0/0] via ::, Loopback0 R 2002:B428:742::1/128 [120/2] via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 R 2005:0:102::/64 [120/2] via FE80::20A:8AFF:FEF0:D981, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104:0:2D0:BAFF:FED3:BA40/128 [0/0] --More-- *Mar 1 09:16:32.589: ICMPv6: Received ICMPv6 packet from FE80::20A:8AFF:FEF0:D981, type 134 --More--   R4#u all All possible debugging has been turned off R4#^Z R4# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b route   r er bgp router bgp 200 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes neighbor 2000:7:7::7 remote-as 100 neighbor 2000:7:7::7 ebgp-multihop 2 neighbor 2000:7:7::7 update-source Loopback1 no neighbor 2000:7:7::7 activate neighbor 2005:0:102:0:213:60FF:FEF0:FD40 remote-as 100 no neighbor 2005:0:102:0:213:60FF:FEF0:FD40 activate neighbor 2005:0:104:0:2D0:BAFF:FED3:BA40 remote-as 300 no neighbor 2005:0:104:0:2D0:BAFF:FED3:BA40 activate no auto-summary ! address-family ipv6 neighbor 2000:7:7::7 activate neighbor 2005:0:102:0:213:60FF:FEF0:FD40 activate neighbor 2005:0:104:0:2D0:BAFF:FED3:BA40 activate network 2006:1:1::/128 exit-address-family ! no ip http server ip classless --More--  ! ! ipv6 route 2000:7:7::7/128 2002:B428:701::1 ipv6 route 2002::/16 Tunnel0 ipv6 router rip R1Rip distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 6 deny 2000:1:1::1/128 ipv6 prefix-list Prob3 seq 7 deny 2002:B428:742::1/128 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 --More--   R1#sh run int tu 0 Building configuration... Current configuration : 167 bytes ! interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:742::1/128 ipv6 rip R1Rip enable tunnel source Ethernet0/0 tunnel mode ipv6ip 6to4 end R1# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b router bgp router bgp 100 no synchronization bgp router-id 2.2.2.2 bgp log-neighbor-changes neighbor 2000:3:3:0:213:7FFF:FE12:A4E0 remote-as 100 no neighbor 2000:3:3:0:213:7FFF:FE12:A4E0 activate neighbor 2005:0:102:0:20A:8AFF:FEF0:D980 remote-as 200 no neighbor 2005:0:102:0:20A:8AFF:FEF0:D980 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3:0:213:7FFF:FE12:A4E0 activate neighbor 2005:0:102:0:20A:8AFF:FEF0:D980 activate network 2006:2:2::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 2.2.2.2 --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b router bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes neighbor 2005:0:237:0:212:43FF:FEAC:6F60 remote-as 100 neighbor 2005:0:237:0:212:43FF:FEAC:6F60 update-source Loopback0 no neighbor 2005:0:237:0:212:43FF:FEAC:6F60 activate neighbor 2005:0:702:0:213:60FF:FEF0:FD40 remote-as 100 neighbor 2005:0:702:0:213:60FF:FEF0:FD40 update-source Loopback0 no neighbor 2005:0:702:0:213:60FF:FEF0:FD40 activate no auto-summary ! address-family ipv6 neighbor 2005:0:237:0:212:43FF:FEAC:6F60 activate neighbor 2005:0:237:0:212:43FF:FEAC:6F60 route-reflector-client neighbor 2005:0:702:0:213:60FF:FEF0:FD40 activate neighbor 2005:0:702:0:213:60FF:FEF0:FD40 route-reflector-client network 2006:3:3::/128 exit-address-family ! ip classless ! no ip http server --More--   R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b router bgp router bgp 300 no synchronization bgp router-id 4.4.4.4 bgp log-neighbor-changes neighbor 2005:0:104:0:20A:8AFF:FEF0:D981 remote-as 200 no neighbor 2005:0:104:0:20A:8AFF:FEF0:D981 activate no auto-summary ! address-family ipv6 neighbor 2005:0:104:0:20A:8AFF:FEF0:D981 activate network 2000:4:4::/64 network 2006:4:4::/128 exit-address-family ! no ip http server no ip http secure-server ip classless ! ! ipv6 route ::/0 FastEthernet0/0 ipv6 router rip R4Rip ! ! --More--   R4# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b router bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:1:1::1 remote-as 200 neighbor 2000:1:1::1 ebgp-multihop 2 neighbor 2000:1:1::1 update-source Loopback1 no neighbor 2000:1:1::1 activate neighbor 2000:3:3:0:213:7FFF:FE12:A4E0 remote-as 100 no neighbor 2000:3:3:0:213:7FFF:FE12:A4E0 activate no auto-summary ! address-family ipv6 neighbor 2000:1:1::1 activate neighbor 2000:3:3:0:213:7FFF:FE12:A4E0 activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! --More--  ipv6 route 2000:1:1::1/128 2002:B428:742::1 ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! ipv6 router rip R7Rip ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 --More--   R7#sh run in t  t tu 0 Building configuration... Current configuration : 202 bytes ! interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:701::1/128 ipv6 address 2005:17:17::7/64 ipv6 rip R7Rip enable tunnel source FastEthernet0/1 tunnel mode ipv6ip 6to4 end R7# R7#