=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.02.09 08:55:57 =~=~=~=~=~=~=~=~=~=~=~= sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 225.1.1.1), 13:26:49/00:01:43, RP 180.40.7.129, flags: BP Bidir-Upstream: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 13:26:49/00:00:00 (*, 224.7.7.7), 13:44:58/00:01:40, RP 180.40.7.129, flags: BPL Bidir-Upstream: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 13:44:59/00:00:00 (*, 224.0.1.40), 14:43:11/00:01:45, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 14:43:11/00:00:00 R7# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip ospfd  Routing Process "ospf 1" with ID 180.40.7.98 Supports only single TOS(TOS0) routes Supports opaque LSA Supports Link-local Signaling (LLS) Initial SPF schedule delay 5000 msecs Minimum hold time between two consecutive SPFs 10000 msecs Maximum wait time between two consecutive SPFs 10000 msecs Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs LSA group pacing timer 240 secs Interface flood pacing timer 33 msecs Retransmission pacing timer 66 msecs Number of external LSA 0. Checksum Sum 0x000000 Number of opaque AS LSA 0. Checksum Sum 0x000000 Number of DCbitless external and opaque AS LSA 0 Number of DoNotAge external and opaque AS LSA 0 Number of areas in this router is 1. 1 normal 0 stub 0 nssa External flood list length 0 Area BACKBONE(0) Number of interfaces in this area is 4 Area has no authentication SPF algorithm last executed 18:14:37.047 ago SPF algorithm executed 14 times Area ranges are --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router ospf 1 R2(config-router)#rout R2(config-router)#router-id 180.40.7.98 R2(config-router)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip ospf Routing Process "ospf 1" with ID 180.40.7.129 Supports only single TOS(TOS0) routes Supports opaque LSA Supports Link-local Signaling (LLS) Initial SPF schedule delay 5000 msecs Minimum hold time between two consecutive SPFs 10000 msecs Maximum wait time between two consecutive SPFs 10000 msecs Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs LSA group pacing timer 240 secs Interface flood pacing timer 33 msecs Retransmission pacing timer 66 msecs Number of external LSA 0. Checksum Sum 0x000000 Number of opaque AS LSA 0. Checksum Sum 0x000000 Number of DCbitless external and opaque AS LSA 0 Number of DoNotAge external and opaque AS LSA 0 Number of areas in this router is 1. 1 normal 0 stub 0 nssa External flood list length 0 Area BACKBONE(0) Number of interfaces in this area is 3 Area has no authentication SPF algorithm last executed 18:15:34.257 ago SPF algorithm executed 14 times Area ranges are --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router ospf 1 R3(config-router)#ropui   ou  uter   R3(config-router)#router-id 180.40.7.129 R3(config-router)#do sh ip int broe  ie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.129 YES manual up up Serial1/0 180.40.7.33 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.3 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--  Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down R3(config-router)#int lo 0 R3(config-if)#ip address 223.254.254.254 255.255.255.255 R3(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-router)#int     do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.98 YES manual up up Serial1/0 unassigned YES manual up up Serial1/0.1 180.40.7.35 YES manual up up Serial1/0.2 180.40.7.65 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.2 YES manual up up Serial1/3 unassigned YES unset administratively down down --More--  Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down R2(config-router)#int lo 0 R2(config-if)#ip address 23 23.254.254.254 255.255.255.255 R2(config-if)#do sh run | b router ospf router ospf 1 router-id 180.40.7.98 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ! access-list 100 permit udp any host 255.255.255.255 eq tftp ! ! ! ! ! ! ! ! ! --More--   R2(config-if)#exit R2(config)#ip pi  ms R2(config)#ip msdp ? cache-rejected-sa Store rejected SAs from all peers default-peer Default MSDP peer to accept SA messages from description Peer specific description filter-sa-request Filter SA-Requests from peer keepalive Configure keepalive parameters for a peer mesh-group Configure an MSDP mesh-group originator-id Configure MSDP Originator ID peer Configure an MSDP peer redistribute Inject multicast route entries into MSDP sa-filter Filter SA messages from peer sa-limit Configure SA limit for a peer shutdown Administratively shutdown MSDP peer timer MSDP timer ttl-threshold Configure TTL Threshold for MSDP Peer vrf Select VPN Routing/Forwarding instance R2(config)#ip msdp pee   r er ? Hostname or A.B.C.D Peer name or address R2(config)#ip msdp peer              int lo 1 R2(config-if)#ip address 2.2.2.2 255.255.255.255 R2(config-if)#3 ^ % Invalid input detected at '^' marker. R2(config-if)# R2(config-if)# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#int loo  1 R3(config-if)#ip adde ress 2 3.3.3.3 255.255.255.255 R3(config-if)#exit R3(config)#ip ms R3(config)#ip msdp peer 2.2.2.2 ? connect-source Configure source address used for MSDP connection remote-as Configured AS number R3(config)#ip msdp peer 2.2.2.2 co R3(config)#ip msdp peer 2.2.2.2 connect-source ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config)#ip msdp peer 2.2.2.2 connect-source lo 1 R3(config)#ip ms R3(config)#ip msdp ? cache-rejected-sa Store rejected SAs from all peers default-peer Default MSDP peer to accept SA messages from description Peer specific description filter-sa-request Filter SA-Requests from peer keepalive Configure keepalive parameters for a peer mesh-group Configure an MSDP mesh-group originator-id Configure MSDP Originator ID peer Configure an MSDP peer redistribute Inject multicast route entries into MSDP sa-filter Filter SA messages from peer sa-limit Configure SA limit for a peer shutdown Administratively shutdown MSDP peer timer MSDP timer ttl-threshold Configure TTL Threshold for MSDP Peer vrf Select VPN Routing/Forwarding instance R3(config)#ip msdp or R3(config)#ip msdp originator-id lo 1 R3(config)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#exit R2(config)#ip md s R2(config)#ip msdp peer 3.3.3.3 ? connect-source Configure source address used for MSDP connection remote-as Configured AS number R2(config)#ip msdp peer 3.3.3.3 co R2(config)#ip msdp peer 3.3.3.3 connect-source lo 1 R2(config)# *Mar 1 21:57:11.205: %MSDP-5-PEER_UPDOWN: Session to peer 3.3.3.3 going up R2(config)#ip msdp co R2(config)#ip msdp co  o R2(config)#ip msdp originator-id lo 1 R2(config)#do sh ip msdp peer MSDP Peer 3.3.3.3 (?), AS ? Connection status: State: Up, Resets: 0, Connection source: Loopback1 (2.2.2.2) Uptime(Downtime): 00:00:14, Messages sent/received: 1/2 Output messages discarded: 0 Connection and counters cleared 00:00:15 ago SA Filtering: Input (S,G) filter: none, route-map: none Input RP filter: none, route-map: none Output (S,G) filter: none, route-map: none Output RP filter: none, route-map: none SA-Requests: Input filter: none Peer ttl threshold: 0 SAs learned from this peer: 0 Input queue size: 0, Output queue size: 0 R2(config)# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config)#do sh ip pim rprip pim rpuip pim rpnip pim rphip pim rp ip pim rpip pim rp ip pim rp  ip pim rp|ip pim rp ip pim rpiip pim rp ip pim rp ip pim rp-candidate FastEthernet0/1 group-list 1 interval 10 bidir R3(config)#no ip pim rp-candidate FastEthernet0/1 group-list 1 interval 10 bi$p-candidate FastEthernet0/1 group-list 1 interval 10 bid ir R3(config)#ip pim rp-candidate lo R3(config)#ip pim rp-candidate loopback 0 grou    in 10 bi R3(config)#ip pim rp-candidate loopback 0 in 10 bidir Warning: PIMv2 not configured on Loopback0, Candidate-RP not advertised R3(config)#int lo 0 R3(config-if)#ip pim sp R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)#ip pim sparse-dense-mode nt lo 0  *Mar 1 21:59:06.698: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback0 (vrf default) R3(config-if)#int lo 0p pim rp-candidate loopback 0 in 10 bidir R3(config)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config)#ip pim rp-candidate loopback 0 in 10 bidir Warning: PIMv2 not configured on Loopback0, Candidate-RP not advertised R2(config)#int lo 0 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#ip pim sparse-dense-mode nt lo 0 p pim rp-candidate loopback 0 in 10 bidir *Mar 1 21:59:33.266: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback0 (vrf default) R2(config-if)#ip pim rp-candidate loopback 0 in 10 bidir R2(config)#^Z R2# *Mar 1 21:59:39.384: %SYS-5-CONFIG_I: Configured from console by console R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:37, expires: 00:02:49 R1# R1# R1# R1# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# S6# S6# S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#sh run int f 0/2 Building configuration... Current configuration : 114 bytes ! interface FastEthernet0/2 no switchport ip address 180.40.7.97 255.255.255.224 ip pim sparse-dense-mode end S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/. 2 S6(config-if)#ip ig S6(config-if)#ip igmp joi S6(config-if)#ip igmp join-group 224.6.6.6 S6(config-if)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 124 ms R1# R1# R1# R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config)#s do sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:07:38/00:03:28, RP 223.254.254.254, flags: BC Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:06:59/00:03:28 (*, 224.6.6.6), 00:02:31/00:00:28, RP 223.254.254.254, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:02:31/00:00:28 (*, 224.0.1.40), 15:10:07/00:02:31, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 15:10:07/00:00:00 Serial1/0, Forward/Sparse-Dense, 15:10:07/00:00:00 Serial1/2, Forward/Sparse-Dense, 15:10:07/00:00:00 R3(config)# *Mar 1 22:06:38.258: %PIM-5-NBRCHG: neighbor 180.40.7.130 DOWN on interface FastEthernet0/1 (vrf default) DR R3(config)# *Mar 1 22:06:59.301: %PIM-5-NBRCHG: neighbor 180.40.7.130 UP on interface FastEthernet0/1 (vrf default) R3(config)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.1.1.1), 00:07:26/00:03:21, RP 223.254.254.254, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:07:26/00:03:21 (*, 225.1.1.1), 00:07:36/00:02:47, RP 223.254.254.254, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:07:36/00:02:47 (*, 224.6.6.6), 00:05:07/00:02:41, RP 223.254.254.254, flags: BC Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:05:07/00:02:41 (*, 224.7.7.7), 00:07:37/00:02:45, RP 223.254.254.254, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: --More--   Serial1/0.2, Forward/Sparse-Dense, 00:07:37/00:02:45 (*, 224.0.1.40), 15:11:20/00:02:38, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 15:11:20/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 15:11:20/00:00:00 Serial1/2, Forward/Sparse-Dense, 15:11:20/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 15:11:20/00:00:00 R2#confifg t ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip mrou R2(config)#ip mroute ? A.B.C.D Source address vrf Select VPN Routing/Forwarding instance R2(config)#ip mroute 180.40.7.66 ? A.B.C.D Network mask R2(config)#ip mroute 180.40.7.66 255.255.255.255 ? A.B.C.D RPF neighbor address or route Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing bgp Border Gateway Protocol (BGP) eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) isis ISO IS-IS iso-igrp IGRP for OSI networks mobile Mobile routes odr On Demand stub Routes --More--   R2(config)#ip mroute 180.40.7.66 255.255.255.255                             224.6.6.6 255.255.255.255 180.40.7.66 ? <0-255> Administrative distance for mroute R2(config)#ip mroute 224.6.6.6 255.255.255.255 180.40.7.66 %Invalid source address R2(config)#ip mroute 224.6.6.6 255.255.255.255 180.40.7.66                                                 do sh ip    run | b     i p ip po im bi ip pim bidir-enable R2(config)#no ip pim bidir-enable R2(config)#no ip pim bidir-enabledo sh run | i ip pim biip mroute 224.6.6.6 255.255.255.255 180.40.7.66 do sh run | i ip pim bi no ip pim bidir-enable  do sh rin    un | i ip pim rp R2(config)#do sh run | i ip pim rpno ip pim bidir-enable do sh run | i ip pim biip mroute 224.6.6.6 255.255.255.255 180.40.7.66 pim rp-candidate loopback 0 in 10 bidir        R2(config)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#no ip pim bidir-enable R1(config)#^Z R1# RACK13AS>2 3 [Resuming connection 3 to r3 ... ] R3(config)#no ip pim bidir-enable R3(config)# R3(config)#no ip pim bidir-enabledo sh ip mroute ip pim rp-candidate loopback 0 in 10 bidir         R3(config)# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#no ip pim bidir-enable ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#no ip pim bidir-enable R4(config)#^Z R4# RACK13AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#no ip pim bidir-enable S5(config)#^Z S5# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6(config-if)#no ip pim bidir-enable S6(config)#^Z S6# 18:41:55: %SYS-5-CONFIG_I: Configured from console by console RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#no ip pim bidir-enable R7(config)#^Z R7# *Mar 1 22:15:08.294: %SYS-5-CONFIG_I: Configured from console by console R7# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#config tsh run int f 0/2ping 224.4.4.4  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 48 ms S6# S6# S6# S6# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config)#^Z R2#sh ip *Mar 1 22:15:07.753: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip pim rp Group: 225.1.1.1, RP: 223.254.254.254, v2, next RP-reachable in 00:00:47 Group: 224.1.1.1, RP: 223.254.254.254, v2, next RP-reachable in 00:00:47 Group: 224.4.4.4, RP: 223.254.254.254, v2, next RP-reachable in 00:01:13 Group: 224.6.6.6, RP: 223.254.254.254, v2, next RP-reachable in 00:00:47 Group: 224.7.7.7, RP: 223.254.254.254, v2, next RP-reachable in 00:00:47 R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config)#^Z R3#sh i *Mar 1 22:15:23.752: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip msdp sa R3#sh ip msdp sa-cache MSDP Source-Active Cache - 1 entries (180.40.7.97, 224.4.4.4), RP 2.2.2.2, AS ?,00:00:31/00:05:28, Peer 2.2.2.2 R3# R3# R3# R3# R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:01:18/00:03:19, RP 223.254.254.254, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:01:18/00:00:00 (180.40.7.97, 224.4.4.4), 00:00:49/00:02:50, flags: M Incoming interface: Serial1/2, RPF nbr 180.40.7.2 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:49/00:00:00 (*, 224.0.1.40), 15:19:45/00:02:57, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 15:19:45/00:00:00 Serial1/0, Forward/Sparse-Dense, 15:19:45/00:00:00 Serial1/2, Forward/Sparse-Dense, 15:19:45/00:00:00 R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b int interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface Loopback1 ip address 2.2.2.2 255.255.255.255 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 225.1.1.1 100 duplex auto speed auto --More--  ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.66 201 broadcast frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown --More--  ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 --More--   no ip address shutdown ! router ospf 1 router-id 180.40.7.98 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 10 ip msdp peer 3.3.3.3 connect-source Loopback1 ip msdp originator-id Loopback1 ! access-list 100 permit udp any host 255.255.255.255 eq tftp ! ! ! ! --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | i b int interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface Loopback1 ip address 3.3.3.3 255.255.255.255 ! interface FastEthernet0/0 no ip address ip pim state-refresh origination-interval 88 shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim dense-mode duplex auto speed auto --More--   R3#sh run | b int interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface Loopback1 ip address 3.3.3.3 255.255.255.255 ! interface FastEthernet0/0 no ip address ip pim state-refresh origination-interval 88 shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim dense-mode duplex auto speed auto --More--  ! interface Serial1/0 ip address 180.40.7.33 255.255.255.224 ip pim sparse-dense-mode encapsulation frame-relay ip ospf network point-to-multipoint ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip pim sparse-dense-mode ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! --More--  interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 180.40.7.129 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim spt-threshold 1 ip pim rp-candidate Loopback0 interval 10 --More--  ip msdp peer 2.2.2.2 connect-source Loopback1 --More--  ip msdp originator-id Loopback1 --More--  ! --More--  access-list 1 deny 224.20.68.1 --More--  access-list 1 permit any --More--   R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh run int fa 0/0 Building configuration... Current configuration : 209 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 88 ip pim dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#ip pim sp R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)#^Z R4# *Mar 1 22:25:11.034: %SYS-5-CONFIG_I: Configured from console by console R4# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int     no ip p mu R3(config)#no ip multicast- R3(config)#no ip multicast-routing R3(config)#int s 1/0 R3(config-if)#no ip pim sp R3(config-if)#no ip pim sparse-d R3(config-if)#no ip pim sparse-dense-mode R3(config-if)#int s *Mar 1 22:23:13.105: %PIM-5-NBRCHG: neighbor 180.40.7.35 DOWN on interface Serial1/0 (vrf default) DR *Mar 1 22:23:13.105: %PIM-5-NBRCHG: neighbor 180.40.7.34 DOWN on interface Serial1/0 (vrf default) non DR R3(config-if)#int s 1/2 R3(config-if)#int s 1/2no ip pim sparse-dense-mode R3(config-if)#int fa 0 *Mar 1 22:23:17.164: %PIM-5-NBRCHG: neighbor 180.40.7.2 DOWN on interface Serial1/2 (vrf default) non DR R3(config-if)#int fa 0/0 1 R3(config-if)#int fa 0/1no ip pim sparse-dense-mode R3(config-if)# *Mar 1 22:23:22.428: %PIM-5-NBRCHG: neighbor 180.40.7.130 DOWN on interface FastEthernet0/1 (vrf default) DR R3(config-if)#exit R3(config)#no ip pim rp R3(config)#no ip pim rp-c R3(config)#no ip pim rp-candidate % Incomplete command. R3(config)#no ip pim rp-candidate lo 0 R3(config)#do sh ip    run | i p ip pim ip pim sparse-dense-mode ip pim state-refresh origination-interval 88 ip pim spt-threshold 1 R3(config)#int lo 0 R3(config-if)#int lo 0do sh run | i ip pimno ip pim rp-candidate lo 0 exit no ip pim sparse-dense-mode R3(config-if)#int fa 0/1 R3(config-if)#no ip pim state-refresh origination-interval 88 R3(config-if)#exit R3(config)#no ip pim spt-threshold 1 R3(config)#no ip msdp R3(config)#no ip msdp            sh no ip pim spt-threshold 1exit no ip pim state-refresh origination-interval 88int fa 0/1 no ip pim sparse-dense-mode int lo 0 do sh run | i ip pim   msdp ip msdp peer 2.2.2.2 connect-source Loopback1 ip msdp originator-id Loopback1 R3(config)#no ip msdp peer 2.2.2.2 connect-source Loopback1 R3(config)#no *Mar 1 22:24:44.679: %MSDP-5-PEER_UPDOWN: Session to peer 2.2.2.2 going down R3(config)#no ip msdp originator-id Loopback1 R3(config)# R3(config)#exit R3# *Mar 1 22:24:59.604: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] *M R2#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R2# RACK13AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES manual up up ATM1/0 192.10.32.13 YES manual up up R4(config)#int lo 0 R4(config-if)#ip adder  ress 4.4.4.4 255.255.255.255 R4(config-if)#int tu 0 R4(config-if)# *Mar 1 22:28:51.570: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R4(config-if)#tun sou lo 0 R4(config-if)#tun des 2.2.2.2 R4(config-if)# *Mar 1 22:2 RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int tu 0 R2(config-if)#tun sou *Mar 1 22:26:50.333: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R2(config-if)#tun sou 12  2.2.2.2 R2(config-if)#tun des 4.4.4.4 R2(config-if)# *Mar 1 22:27:01.163: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R2(config-if)#ip add 24.24.24.2 255.255.255.0 R2(config-if)# RACK13AS>4 [Resuming connection 4 to r4 ... ] 958: %LINEPROTO-5-U R4(config-if)#ip add 24.14.   24.24.2 4 255,.25    .5255.25       5 255.255.0 R4(config-if)#ip pim sp R4(config-if)#ip pim sparse- *Mar 1 22:30:21.502: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Mar R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)# *Mar 1 22:28:08.838: %PIM-5-NBRCHG: neighbor 24.24.24.4 UP on interface Tunnel0 (vrf default) R2(config-if)#do sh ip int   pos   ospf int tu 0 Tunnel0 is up, line protocol is up Internet Address 24.24.24.2/24, Area 0 Process ID 1, Router ID 180.40.7.98, Network Type POINT_TO_POINT, Cost: 11111 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 Hello due in 00:00:02 Index 7/7, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 192.10.32.13 Suppress hello for 0 neighbor(s) R2(config-if)#pin   dp o p 24.24.24.4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 24.24.24.4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 36/39/40 ms R2(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/791] via 180.40.7.66, 00:01:21, Serial1/0.2 O 17.100.1.0 [110/791] via 180.40.7.66, 00:01:21, Serial1/0.2 2.0.0.0/32 is subnetted, 1 subnets C 2.2.2.2 is directly connected, Loopback1 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/782] via 180.40.7.3, 00:01:21, Serial1/2 223.254.254.0/32 is subnetted, 1 subnets C 223.254.254.254 is directly connected, Loopback0 4.0.0.0/32 is subnetted, 1 subnets O 4.4.4.4 [110/783] via 180.40.7.3, 00:01:22, Serial1/2 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More--  O 192.10.32.0/24 [110/783] via 180.40.7.3, 00:01:24, Serial1/2 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.128/27 [110/782] via 180.40.7.3, 00:01:24, Serial1/2 C 180.40.7.0/27 is directly connected, Serial1/2 O 180.40.7.33/32 [110/781] via 180.40.7.3, 00:01:24, Serial1/2 C 180.40.7.32/27 is directly connected, Serial1/0.1 O 180.40.7.66/32 [110/781] via 180.40.7.66, 00:01:24, Serial1/0.2 C 180.40.7.64/27 is directly connected, Serial1/0.2 C 180.40.7.96/27 is directly connected, FastEthernet0/1 R2(config-if)#d p 224.4.4.4 % Ambiguous command: "d p 224.4.4.4" R2(config-if)#d p 224.4.4.40 p 224.4.4.4 p 224.4.4.4 o p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 60 ms R2(config-if)# R2(config-if)# R2(config-if)# R2(config-if)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#sh ip int brie Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES manual administratively down down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 180.40.7.97 YES manual up up FastEthernet0/3 unassigned YES unset up up FastEthernet0/4 unassigned YES unset up up FastEthernet0/5 unassigned YES unset down down FastEthernet0/6 unassigned YES unset down down FastEthernet0/7 unassigned YES unset up up FastEthernet0/8 unassigned YES unset down down FastEthernet0/9 unassigned YES unset down down FastEthernet0/10 unassigned YES unset down down FastEthernet0/11 unassigned YES unset down down FastEthernet0/12 unassigned YES unset down down FastEthernet0/13 unassigned YES unset down down FastEthernet0/14 unassigned YES unset down down FastEthernet0/15 unassigned YES unset down down FastEthernet0/16 unassigned YES unset down down FastEthernet0/17 unassigned YES unset down down FastEthernet0/18 unassigned YES unset down down FastEthernet0/19 unassigned YES unset down down FastEthernet0/20 unassigned YES unset down down FastEthernet0/21 unassigned YES unset down down --More--   S6# RACK13AS>4 [Resuming connection 4 to r4 ... ] *Ma R4(config-if)#^Z R4#sh *Mar 1 22:33:52.410: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip route 180.40.7.97 Routing entry for 180.40.7.96/27 Known via "ospf 1", distance 110, metric 783, type intra area Last update from 180.40.7.129 on FastEthernet0/0, 00:03:20 ago Routing Descriptor Blocks: * 180.40.7.129, from 180.40.7.98, 00:03:20 ago, via FastEthernet0/0 Route metric is 783, traffic share count is 1 R4# R4# R4# R4# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#dop    sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 225.1.1.1), 00:11:09/00:03:10, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:11:09/00:03:10 (*, 224.1.1.1), 00:11:09/00:03:13, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:11:09/00:03:13 (*, 224.4.4.4), 00:09:28/00:01:41, RP 223.254.254.254, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.6.6.6), 00:11:15/00:02:17, RP 223.254.254.254, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:11:15/00:02:17 --More--   (*, 224.7.7.7), 00:11:10/00:03:08, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:11:10/00:03:08 (*, 224.0.1.40), 15:38:50/00:02:10, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:06:39/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 15:38:50/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 15:38:50/00:00:00 R2(config-if)#do sh ip mroutep 224.4.4.4  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 56 ms R2(config-if)#do p 224.4.4.4sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 225.1.1.1), 00:11:29/00:02:50, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:11:29/00:02:50 (*, 224.1.1.1), 00:11:29/00:02:53, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:11:29/00:02:53 (*, 224.4.4.4), 00:09:49/stopped, RP 223.254.254.254, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.65, 224.4.4.4), 00:00:05/00:02:54, flags: PA Incoming interface: Serial1/0.2, RPF nbr 0.0.0.0 Outgoing interface list: Null --More--  (180.40.7.98, 224.4.4.4), 00:00:06/00:02:53, flags: PTA Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Null (223.254.254.254, 224.4.4.4), 00:00:06/00:02:53, flags: PTA Incoming interface: Loopback0, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.6.6.6), 00:11:37/00:02:52, RP 223.254.254.254, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:11:37/00:02:52 (*, 224.7.7.7), 00:11:32/00:02:47, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:11:32/00:02:47 (*, 224.0.1.40), 15:39:11/00:02:47, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:07:00/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 15:39:11/00:00:00 --More--   FastEthernet0/1, Forward/Sparse-Dense, 15:39:11/00:00:00 R2(config-if)# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:10:03/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:08:18/00:00:00 FastEthernet0/0, Forward/Sparse-Dense, 00:10:03/00:00:00 (24.24.24.2, 224.4.4.4), 00:01:23/00:01:38, flags: LT Incoming interface: Tunnel0, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Sparse-Dense, 00:01:25/00:00:00 (*, 224.0.1.40), 14:56:54/00:02:19, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:08:19/00:00:00 FastEthernet0/0, Forward/Sparse-Dense, 14:56:54/00:00:00 R4# sh ip m pim rp map PIM Group-to-RP Mappings R4# sh ip pim rp map                 config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 \ 0 R4(config-if)#no ip pim sp R4(config-if)#no ip pim sparse-d R4(config-if)#no ip pim sparse-dense-mode R4(config-if)#int lo 0 R4(config-if)#ip pim sp R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)#ip igm R4(config-if)#ip igmp *Mar 1 22:43:03.610: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 4.4.4.4 on interface Loopback0 (vrf default) R4(config-if)#ip igmp jo R4(config-if)#ip igmp join-group 224.244   4.4.4 R4(config-if)# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#do sh ip mroutep 224.4.4.4  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 56 ms R2(config-if)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip int brieping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config-if)# R4(config-if)#do sh ip pim rp map PIM Group-to-RP Mappings R4(config-if)#exit R4(config)#ip mrou R4(config)#ip mroute 0.0.0.0 0.0.0.0 tu 0 R4(config)# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 36 ms S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 36 ms S6# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config)#do sh run | i ip mroute ip mroute 0.0.0.0 0.0.0.0 Tunnel0 R4(config)#sh ip       do sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:20:23/00:02:20, RP 223.254.254.254, flags: SCL Incoming interface: Tunnel0, RPF nbr 24.24.24.2, Mroute Outgoing interface list: Loopback0, Forward/Sparse-Dense, 00:05:57/00:02:09 (*, 224.0.1.40), 15:07:13/00:02:09, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:18:38/00:00:00 R4(config)#sh  do sh ip[    pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:01:06, expires: 00:03:20 R4(config)# R4# *Mar 1 22:49:43.998: %SYS-5-CONFIG_I: Configured from console by console R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#do sh ip pim rp mapmroute run | i ip mrouteip mroute 0.0.0.0 0.0.0.0 tu 0nip mroute 0.0.0.0 0.0.0.0 tu 0oip mroute 0.0.0.0 0.0.0.0 tu 0 ip mroute 0.0.0.0 0.0.0.0 tu 0 R4(config)#router ospf 1 R4(config-router)#net 4.4.4.4 0.0.0.0 area 4 51 R4(config-router)# *Mar 1 22:50:32.082: %OSPF-6-AREACHG: 4.4.4.4/32 changed from area 0 to area 51 R4(config-router)#int     net 180.40.7.130 0.0.0.0 area 51 R4(config-router)# *Mar 1 22:50:54.546: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-router)# *Mar 1 22:50:54.550: %OSPF-6-AREACHG: 180.40.7.130/32 changed from area 0 to area 51 R4(config-router)# *Mar 1 22:50:54.578: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.129, FastEthernet0/0 R4(config-router)#^Z R4# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#router *Mar 1 22:48:39.383: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 22:48:40.385: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 22:48:40.385: %PIM-5-NBRCHG: neighbor 24.24.24.4 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 22:48:40.385: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.13 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R2(config-if)#router ospf 1 R2(config-router)#net 2.2.2.2 0.0.0.0 REa     AREA 51 R2(config-router)#ne *Mar 1 22:48:53.506: %OSPF-6-AREACHG: 2.2.2.2/32 changed from area 0 to area 51 R2(config-router)#net 180.40.7.3 0.0.0.0 area 51 R2(config-router)#^Z R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#net 180.40.7.3 0.0.0.0 area 512.2.2.2 0.0.0.0 AREA 51 router ospf 1  R2(config-router)#router ospf 1net 180.40.7.3 0.0.0.0 area 515 0.0.0.0 area 51 R2(config-router)#^Z R2# *Mar 1 22:49:42.587: %OSPF-6-AREACHG: 180.40.7.35/32 changed from area 0 to area 51 R2# *Mar 1 22:49:43.809: %SYS-5-CONFIG_I: Configured from console by console R2#^x1 % Unknown command or computer name, or unable to find computer address R2# R2# RACK13AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#router ospf 1 R1(config-router)#net 180.        ^Z R1# *Mar 1 22:52:00.445: %SYS-5-CONFIG_I: Configured from console by console R1# RACK13AS>3 [Resuming connection 3 to r3 ... ] R3(config)#router ospf 1 R3(config-router)#net 0.0.0.0 255.255.255.255 ara   ea 51 R3(config-router)# *Mar 1 22:51:37.251: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-router)# *Mar 1 22:51:37.259: %OSPF-6-AREACHG: 0.0.0.0/0 changed from area 0 to area 51 R3(config-router)#^Z R3# *Mar 1 22:51:38.985: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3# *Mar 1 22:51:39.078: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 22:51:43.333: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.13 on FastEthernet0/1 from LOADING to FULL, Loading Done R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.129 1 FULL/BDR 00:00:35 180.40.7.129 FastEthernet0/0 R4#sh ip ospf int Tunnel0 is up, line protocol is down Internet Address 24.24.24.4/24, Area 0 Process ID 1, Router ID 192.10.32.13, Network Type POINT_TO_POINT, Cost: 11111 Transmit Delay is 1 sec, State DOWN, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 ATM1/0 is up, line protocol is up Internet Address 192.10.32.13/24, Area 0 Process ID 1, Router ID 192.10.32.13, Network Type NON_BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 192.10.32.13, Interface address 192.10.32.13 No backup designated router on this network Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 oob-resync timeout 120 Hello due in 00:00:26 Index 2/2, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) FastEthernet0/0 is up, line protocol is up Internet Address 180.40.7.130/27, Area 51 --More--   R4#sh ip ospf intneiroute  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:00:24, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:24, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:25, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:25, FastEthernet0/0 R4# RACK13AS>2 3 [Resuming connection 3 to r3 ... ] *Mar R3#sh ip ospf neoi  i Neighbor ID Pri State Dead Time Address Interface 192.10.32.13 1 FULL/DR 00:00:34 180.40.7.130 FastEthernet0/1 R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 192.10.32.13 1 FULL/DR 00:00:32 180.40.7.130 FastEthernet0/1 R3# *Mar 1 22:52:39.016: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 192.10.32.13 1 FULL/DR 00:00:35 180.40.7.130 FastEthernet0/1 R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 192.10.32.13 1 FULL/DR 00:00:34 180.40.7.130 FastEthernet0/1 R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 192.10.32.13 1 FULL/DR 00:00:33 180.40.7.130 FastEthernet0/1 R3# *Mar 1 22:52:48.932: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 192.10.32.13 1 FULL/DR 00:00:30 180.40.7.130 FastEthernet0/1 R3# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Ma R2# R2#sh ip proto Routing Protocol is "ospf 1" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Router ID 180.40.7.98 It is an area border router Number of areas in this router is 2. 2 normal 0 stub 0 nssa Maximum path: 4 Routing for Networks: 2.2.2.2 0.0.0.0 area 51 180.40.7.3 0.0.0.0 area 51 180.40.7.35 0.0.0.0 area 51 0.0.0.0 255.255.255.255 area 0 Routing Information Sources: Gateway Distance Last Update 180.40.7.129 110 00:03:10 17.57.100.2 110 00:00:43 17.100.1.2 110 00:00:43 180.40.7.66 110 00:00:43 192.10.32.13 110 00:04:20 Distance: (default is 110) R2# RACK13AS> [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router r ospf 1 R2(config-router)#router ospf 1net 180.40.7.35 0.0.0.0 area 51router ospf 1 net 180.40.7.3 0.0.0.0 area 51nnet 180.40.7.3 0.0.0.0 area 51onet 180.40.7.3 0.0.0.0 area 51 net 180.40.7.3 0.0.0.0 area 51 R2(config-router)#no net 180.40.7.3 0.0.0.0 area 51router ospf 1 net 180.40.7.35 0.0.0.0 area 51router ospf 1 net 180.40.7.3 0.0.0.0 area 51 0.0.0.0 area 51 2 0.0.0.0 area 51 R2(config-router)#^Z R2# *Mar 1 22:53:27.239: %OSPF-6-AREACHG: 180.40.7.2/32 changed from area 0 to area 51 R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] * R3# *Mar 1 22:53:29.002: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3#sh ip protop  Routing Protocol is "ospf 1" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Router ID 180.40.7.129 Number of areas in this router is 1. 1 normal 0 stub 0 nssa Maximum path: 4 Routing for Networks: 0.0.0.0 255.255.255.255 area 51 Routing Information Sources: Gateway Distance Last Update 17.57.100.2 110 00:03:46 17.100.1.2 110 00:03:46 180.40.7.66 110 00:03:46 192.10.32.13 110 00:01:43 180.40.7.98 110 00:03:46 Distance: (default is 110) R3#con *Mar 1 22:53:37.424: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial1/2 from LOADING to FULL, Loading Done R3#config t *Mar 1 22:53:39.018: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3#config t        ^Z R3#sh ip protoospf neiconfig t sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.98 0 FULL/ - 00:00:38 180.40.7.2 Serial1/2 192.10.32.13 1 FULL/DR 00:00:35 180.40.7.130 FastEthernet0/1 R3# *Mar 1 22:53:48.935: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O IA 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:08, FastEthernet0/0 O IA 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:08, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:08, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:00:08, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.25 *Mar 1 22:56:21.566: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 22:56:21.594: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) 4.254 [110/2] via 180.40.7.129, 00:00:10, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More-- *Mar 1 22:56:22.794: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done --More--  C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 4 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:10, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:10, FastEthernet0/0 O 180.40.7.32/27 [110/1563] via 180.40.7.129, 00:00:10, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:17, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:00:17, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:17, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 4 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 --More--  O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:19, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:19, FastEthernet0/0 O 180.40.7.32/27 [110/1563] via 180.40.7.129, 00:00:19, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/11902] via 24.24.24.2, 00:00:16, Tunnel0 O 17.100.1.0 [110/11902] via 24.24.24.2, 00:00:16, Tunnel0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:36, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:00:36, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:00:36, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More--  C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:37, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:37, FastEthernet0/0 O 180.40.7.32/27 [110/1563] via 180.40.7.129, 00:00:37, FastEthernet0/0 O 180.40.7.66/32 [110/11892] via 24.24.24.2, 00:00:17, Tunnel0 O 180.40.7.65/32 [110/11111] via 24.24.24.2, 00:00:17, Tunnel0 O 180.40.7.96/27 [110/11112] via 24.24.24.2, 00:00:17, Tunnel0 R4# R4# R4# R4# R4# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:09, expires: 00:03:19 R4# RACK13AS> [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/11902] via 24.24.24.2, 00:01:02, Tunnel0 O 17.100.1.0 [110/11902] via 24.24.24.2, 00:01:02, Tunnel0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:01:22, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:01:22, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:01:22, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More--  C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:01:27, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:01:27, FastEthernet0/0 O 180.40.7.32/27 [110/1563] via 180.40.7.129, 00:01:27, FastEthernet0/0 O 180.40.7.66/32 [110/11892] via 24.24.24.2, 00:01:07, Tunnel0 O 180.40.7.65/32 [110/11111] via 24.24.24.2, 00:01:07, Tunnel0 O 180.40.7.96/27 [110/11112] via 24.24.24.2, 00:01:07, Tunnel0 R4# RACK13AS> [Resuming connection 4 to r4 ... ] R4#sh ip ospf int Tunnel0 is up, line protocol is up Internet Address 24.24.24.4/24, Area 0 Process ID 1, Router ID 192.10.32.13, Network Type POINT_TO_POINT, Cost: 11111 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 Hello due in 00:00:06 Index 4/4, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 4 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 180.40.7.98 Suppress hello for 0 neighbor(s) ATM1/0 is up, line protocol is up Internet Address 192.10.32.13/24, Area 0 Process ID 1, Router ID 192.10.32.13, Network Type NON_BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 192.10.32.13, Interface address 192.10.32.13 No backup designated router on this network Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 oob-resync timeout 120 Hello due in 00:00:02 --More--   Index 2/2, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) FastEthernet0/0 is up, line protocol is up Internet Address 180.40.7.130/27, Area 51 Process ID 1, Router ID 192.10.32.13, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 192.10.32.13, Interface address 180.40.7.130 Backup Designated router (ID) 180.40.7.129, Interface address 180.40.7.129 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 Hello due in 00:00:05 Index 2/1, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 6, maximum is 6 Last flood scan time is 0 msec, maximum is 4 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 180.40.7.129 (Backup Designated Router) Suppress hello for 0 neighbor(s) Loopback0 is up, line protocol is up --More--   Internet Address 4.4.4.4/32, Area 51 Process ID 1, Router ID 192.10.32.13, Network Type LOOPBACK, Cost: 1 Loopback interface is treated as a stub Host R4# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK13AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#ping 225.5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 225.5.5.5, timeout is 2 seconds: . R2# [Special telnet escape help] ^^B sends telnet BREAK ^^C sends telnet IP ^^H sends telnet EC ^^O sends telnet AO ^^T sends telnet AYT ^^U sends telnet EL ping 225.5.5.5  R2#ping 225.5.5.5    config t sh ip proto^x1 config tping 224.4.4.4sh run | b intping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R2#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 225.1.1.1), 00:32:51/00:03:13, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:32:51/00:03:13 (*, 224.1.1.1), 00:32:51/00:03:10, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:32:51/00:03:10 (*, 224.4.4.4), 00:01:35/stopped, RP 223.254.254.254, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.65, 224.4.4.4), 00:00:07/00:02:52, flags: PA Incoming interface: Serial1/0.2, RPF nbr 0.0.0.0 Outgoing interface list: Null --More--  (180.40.7.97, 224.4.4.4), 00:01:37/00:02:29, flags: PTA Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.98, 224.4.4.4), 00:00:09/00:02:59, flags: PTA Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Null (223.254.254.254, 224.4.4.4), 00:00:09/00:02:59, flags: PTA Incoming interface: Loopback0, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 225.5.5.5), 00:00:20/stopped, RP 223.254.254.254, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.65, 225.5.5.5), 00:00:20/00:02:39, flags: PA Incoming interface: Serial1/0.2, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.98, 225.5.5.5), 00:00:20/00:02:39, flags: PTA Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Null --More--   (223.254.254.254, 225.5.5.5), 00:00:34/00:02:25, flags: PTA Incoming interface: Loopback0, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.6.6.6), 00:33:13/00:02:15, RP 223.254.254.254, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:33:13/00:02:15 (*, 224.7.7.7), 00:33:08/00:02:47, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:33:08/00:02:47 (*, 224.0.1.40), 16:00:48/00:02:12, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:02:46/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 16:00:48/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 16:00:48/00:00:00 R2#sh ip mroute sh ip mrouteping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R2# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#confif t ^ % Invalid input detected at '^' marker. R4#confifg t ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/1 0 R4(config-if)#ip pim sp R4(config-if)#ip pim sparse- R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)# *Mar 1 22:59:51.650: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.130 on interface FastEthernet0/0 (vrf default) R4(config-if)#int lo 0 R4(config-if)#int lo 0p pim sparse-dense-mode  nt fa 0/0 net 180.40.7.130 0.0.0.0 area 514.4.4.4 0.0.0.0 area 51 router ospf 1 no ip mroute 0.0.0.0 0.0.0.0 tu 0do sh ip pim rp map mroute run | i ip mrouteip mroute 0.0.0.0 0.0.0.0 tu 0exit do sh ip pim rp mapip igmp join-group 224.4.4.4nip igmp join-group 224.4.4.4oip igmp join-group 224.4.4.4 ip igmp join-group 224.4.4.4 R4(config-if)#int fa 0/1 ^ % Invalid input detected at '^' marker. R4(config)#int fa 0/1no ip igmp join-group 224.4.4.4int fa 0/1 no ip igmp join-group 224.4.4.4int fa 0/1  0 R4(config-if)#int fa 0/01no ip igmp join-group 224.4.4.4nno ip igmp join-group 224.4.4.4ono ip igmp join-group 224.4.4.4 no ip igmp join-group 224.4.4.4no ip igmp join-group 224.4.4.4 no ip igmp join-group 224.4.4.4 o ip igmp join-group 224.4.4.4 no ip igmp join-group 224.4.4.4  ip igmp join-group 224.4.4.4  R4(config-if)#^Z R4# *Mar 1 23:00:19.186: %SYS-5-CONFIG_I: Configured from console by console R4# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 60 ms R2# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/11902] via 24.24.24.2, 00:04:17, Tunnel0 O 17.100.1.0 [110/11902] via 24.24.24.2, 00:04:17, Tunnel0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:04:37, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:04:37, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 180.40.7.129, 00:04:37, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More--  C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:04:39, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:04:39, FastEthernet0/0 O 180.40.7.32/27 [110/1563] via 180.40.7.129, 00:04:39, FastEthernet0/0 O 180.40.7.66/32 [110/11892] via 24.24.24.2, 00:04:19, Tunnel0 O 180.40.7.65/32 [110/11111] via 24.24.24.2, 00:04:19, Tunnel0 O 180.40.7.96/27 [110/11112] via 24.24.24.2, 00:04:19, Tunnel0 R4#m RACK13AS> [Resuming connection 4 to r4 ... ] % Incomplete command. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#^Z R4# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no int lo 0 R3(config)# *Mar 1 22:59:29.004: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3(config)# *Mar 1 22:59:31.684: %LINK-5-CHANGED: Interface Loopback0, changed state to administratively down R3(config)#do sh ip int *Mar 1 22:59:39.020: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3(config)#do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down BRI0/0 unassigned YES unset administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.129 YES manual up up Serial1/0 180.40.7.33 YES manual up up Serial1/1 unassigned YES unset administratively down down Serial1/2 180.40.7.3 YES manual up up Serial1/3 unassigned YES unset administratively down down Serial1/4 unassigned YES unset administratively down down Serial1/5 unassigned YES unset administratively down down --More--  Serial1/6 unassigned YES unset administratively down down Serial1/7 unassigned YES unset administratively down down Loopback1 3.3.3.3 YES manual up up R3(config)#^Z R3# *Mar 1 22:59:45.431: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 22:59:48.961: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] * R4#config tm sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/11902] via 24.24.24.2, 00:05:45, Tunnel0 O 17.100.1.0 [110/11902] via 24.24.24.2, 00:05:45, Tunnel0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:22, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:00:22, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/11112] via 24.24.24.2, 00:00:22, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More--  C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:25, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:25, FastEthernet0/0 O 180.40.7.32/27 [110/1563] via 180.40.7.129, 00:00:25, FastEthernet0/0 O 180.40.7.66/32 [110/11892] via 24.24.24.2, 00:05:47, Tunnel0 O 180.40.7.65/32 [110/11111] via 24.24.24.2, 00:05:47, Tunnel0 O 180.40.7.96/27 [110/11112] via 24.24.24.2, 00:05:47, Tunnel0 R4# RACK13AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 44 ms S6# RACK13AS>1 7 [Resuming connection 7 to r7 ... ] R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 108 ms R7# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#^Z R4#sh *Mar 1 23:03:46.626: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip pim ro p Group: 224.4.4.4, RP: 223.254.254.254, v2, uptime 00:06:33, expires 00:02:51 R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int tu 0 R4(config-if)#ip igp R4(config-if)#ip igp  R4(config-if)#ip igmp jo R4(config-if)#ip igmp join-group 224.44.44.44 R4(config-if)# RACK13AS>1 [Resuming connection 1 to r1 ... ] R1# RACK13AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.44.44.44 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.44.44.44, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 109 ms R7# R7# R7# RACK13AS>2 [Resuming connection 2 to r2 ... ] R2#sh sh  run | b int  erface Tun interface Tunnel0 ip address 24.24.24.2 255.255.255.0 ip pim sparse-dense-mode tunnel source 2.2.2.2 tunnel destination 4.4.4.4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 225.1.1.1 100 duplex auto speed auto ! --More--  interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.66 201 broadcast frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! --More--  interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address --More--   shutdown ! router ospf 1 router-id 180.40.7.98 log-adjacency-changes network 2.2.2.2 0.0.0.0 area 51 network 180.40.7.2 0.0.0.0 area 51 network 180.40.7.35 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 10 ip msdp peer 3.3.3.3 connect-source Loopback1 ip msdp originator-id Loopback1 ! access-list 100 permit udp any host 255.255.255.255 eq tftp ! ! --More--   R2# RACK13AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 22:59:5 R3#sh *Mar 1 23:16:59.005: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 R3#sh run | b router router ospf 1 router-id 180.40.7.129 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 51 ! ip classless ! no ip http server no ip http secure-server ! access-list 1 deny 224.20.68.1 access-list 1 permit any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 --More-- *Mar 1 23:17:09.078: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.34, Serial1/0 --More--   R3# RACK13AS>4 [Resuming connection 4 to r4 ... ] R4(config-if)#^Z R4#Sh run | *Mar 1 23:19:41.962: %SYS-5-CONFIG_I: Configured from console by console R4#Sh run | b interface Tun interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode ip igmp join-group 224.44.44.44 tunnel source Loopback0 tunnel destination 2.2.2.2 ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 88 ip pim sparse-dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto ! interface ATM1/0 ip address 192.10.32.13 255.255.255.0 ip nat outside no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 broadcast ! --More--  ! router ospf 1 log-adjacency-changes network 4.4.4.4 0.0.0.0 area 51 network 180.40.7.130 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ip nat inside source list IPNAT interface ATM1/0 overload no ip http server no ip http secure-server ip classless ! ip pim spt-threshold 1 ! ! ip access-list standard IPNAT permit 180.40.7.0 0.0.0.255 permit 17.0.0.0 0.255.255.255 ! ! ! ! ! --More--   R4# [Connection to r4 closed by foreign host] RACK13AS>