=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.02.07 09:08:56 =~=~=~=~=~=~=~=~=~=~=~= RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES manual up up ATM1/0 unassigned YES unset administratively down down R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo 0 R4(config-if)#ip addess 100.1.1.1 255.255.255.0 ^ % Invalid input detected at '^' marker. R4(config-if)#ip addess 100.1.1.1 255.255.255.0ress 100.1.1.1 255.255.255.0 R4(config-if)#^Z R4# *Mar 1 18:30:29.131: %SYS-5-CONFIG_I: Configured from console by console R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip access-list R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#access-list ? <1-99> IP standard access list <100-199> IP extended access list <1000-1099> IPX SAP access list <1100-1199> Extended 48-bit MAC address access list <1200-1299> IPX summary address access list <1300-1999> IP standard access list (expanded range) <200-299> Protocol type-code access list <2000-2699> IP extended access list (expanded range) <300-399> DECnet access list <600-699> Appletalk access list <700-799> 48-bit MAC address access list <800-899> IPX standard access list <900-999> IPX extended access list dynamic-extended Extend the dynamic ACL absolute timer rate-limit Simple rate-limit specific access list R3(config)#access-list 100 ? deny Specify packets to reject dynamic Specify a DYNAMIC list of PERMITs or DENYs permit Specify packets to forward remark Access list entry comment R3(config)#access-list 100 per ip    icmp ost 100.1.1.1 host 100.1.1.1 ost 100.1.1.1 host 20.10.1.2 ? <0-255> ICMP message type administratively-prohibited Administratively prohibited alternate-address Alternate address conversion-error Datagram conversion dod-host-prohibited Host prohibited dod-net-prohibited Net prohibited dscp Match packets with given dscp value echo Echo (ping) echo-reply Echo reply fragments Check non-initial fragments general-parameter-problem Parameter problem host-isolated Host isolated host-precedence-unreachable Host unreachable for precedence host-redirect Host redirect host-tos-redirect Host redirect for TOS host-tos-unreachable Host unreachable for TOS host-unknown Host unknown host-unreachable Host unreachable information-reply Information replies information-request Information requests log Log matches against this entry log-input Log matches against this entry, including input --More--   R3(config)#access-list 100 per icmp host 100.1.1.1 host 20.10.1.2 echo R3(config)#access-list 100 per icmp host 100.1.1.1 host 20.10.1.2 echo echo 1 echoaccess-list 100 per icmp host 100.1.1.1 host 20.10.1.1 echo 1 per icmp host 100.1.1.1 host 20.10.1.1 echo R3(config)#access-list 101 per icmp host 100.1.1.1 host 20.10.1.1 echo echo 0 echo echo0 echo. echo0 echo. echo0 echo. echo2 echo5 echo5 ec$ 20.10.1.0 0.0.0.255 echo 20.10.1.0 0.0.0.255 echo  20.10.1.0 0.0.0.255 echo  20.10.1.0 0.0.0.255 echo  per icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo 2 per icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo R3(config)#route-mp   ap Prob1 R3(config-route-map)#match ? as-path Match BGP AS path list clns CLNS information community Match BGP community list extcommunity Match BGP/VPN extended community list interface Match first hop interface of route ip IP specific information ipv6 IPv6 specific information length Packet length metric Match metric of route mpls-label Match routes which have MPLS labels nlri BGP NLRI type policy-list Match IP policy list route-type Match route-type of route tag Match tag of route R3(config-route-map)#match ip 10  add 102 R3(config-route-map)#ma R3(config-route-map)#match l R3(config-route-map)#match length ? <0-2147483647> Minimum packet length R3(config-route-map)#match length 1001 ? <0-2147483647> Maximum packet length R3(config-route-map)#match length 1001 2147483647 R3(config-route-map)#match length 1001 2147483647            1 % Incomplete command. R3(config-route-map)# match length 1001 % Incomplete command. R3(config-route-map)#match length 1001   2147483647 R3(config-route-map)#exit R3(config)#exitmatch length 1001 2147483647   2147483647ip add 102 route-map Prob1  20 R3(config-route-map)#match ip add 102 1 0 R3(config-route-map)#set ? as-path Prepend string for a BGP AS-path attribute automatic-tag Automatically compute TAG value clns OSI summary address comm-list set BGP community list (for deletion) community BGP community attribute dampening Set BGP route flap dampening parameters default Set default information extcommunity BGP extended community attribute interface Output interface ip IP specific information ipv6 IPv6 specific information level Where to import route local-preference BGP local preference path attribute metric Metric value for destination routing protocol metric-type Type of metric for destination routing protocol mpls-label Set MPLS label for prefix nlri BGP NLRI type origin BGP origin code tag Tag value for destination routing protocol traffic-index BGP traffic classification number for accounting weight BGP weight for routing table R3(config-route-map)#set ip ? address Specify IP address default Set default information df Set DF bit next-hop Next hop address precedence Set precedence field qos-group Set QOS Group ID tos Set type of service field R3(config-route-map)#set ip ne R3(config-route-map)#set ip next-hop ? A.B.C.D IP address of next hop peer-address Use peer address (for BGP only) verify-availability Verify if nexthop is a CDP neighbor R3(config-route-map)#set ip next-hop 180  .40.7.67 R3(config-route-map)#set ip next-hop 180.40.7.67match ip add 100 route-map Prob1 20  10 R3(config-route-map)#set ? as-path Prepend string for a BGP AS-path attribute automatic-tag Automatically compute TAG value clns OSI summary address comm-list set BGP community list (for deletion) community BGP community attribute dampening Set BGP route flap dampening parameters default Set default information extcommunity BGP extended community attribute interface Output interface ip IP specific information ipv6 IPv6 specific information level Where to import route local-preference BGP local preference path attribute metric Metric value for destination routing protocol metric-type Type of metric for destination routing protocol mpls-label Set MPLS label for prefix nlri BGP NLRI type origin BGP origin code tag Tag value for destination routing protocol traffic-index BGP traffic classification number for accounting weight BGP weight for routing table R3(config-route-map)#set in R3(config-route-map)#set interface s 1/2 R3(config-route-map)#set interface s 1/2route-map Prob1 10   30 R3(config-route-map)#match ip add 102 1 R3(config-route-map)#match ip add 101route-map Prob1 30set interface s 1/2 R3(config-route-map)#int fa 0/0 R3(config-if)#ip pol R3(config-if)#ip policy rou R3(config-if)#ip policy route-map Prob1 R3(config-if)#^Z R3#shj *Mar 1 18:48:15.410: %SYS-5-CONFIG_I: Configured from console by console R3#shj    route route-map Prob1, permit, sequence 10 Match clauses: ip address (access-lists): 102 length 1001 2147483647 Set clauses: interface Serial1/2 Policy routing matches: 0 packets, 0 bytes route-map Prob1, permit, sequence 20 Match clauses: ip address (access-lists): 100 Set clauses: ip next-hop 180.40.7.67 Policy routing matches: 0 packets, 0 bytes route-map Prob1, permit, sequence 30 Match clauses: ip address (access-lists): 101 Set clauses: interface Serial1/2 Policy routing matches: 0 packets, 0 bytes R3#sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 48 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: disabled, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 54 message lines logged R3#s deb ip pol R3#deb ip policy Policy routing debugging is on R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 00:21:31, FastEthernet0/0 [110/793] via 180.40.7.131, 00:21:31, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.129, 00:21:31, FastEthernet0/0 [110/783] via 180.40.7.131, 00:21:31, FastEthernet0/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:21:31, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.129, 00:21:32, FastEthernet0/0 [110/782] via 180.40.7.131, 00:21:32, FastEthernet0/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:21:32, FastEthernet0/0 --More--   R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:21:53, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.67, 00:21:53, Serial1/0 O 20.10.1.0 [110/782] via 180.40.7.67, 00:21:53, Serial1/0 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:21:53, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:21:54, Serial1/0 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:21:54, FastEthernet0/0 O 180.40.7.67/32 [110/781] via 180.40.7.67, 00:21:54, Serial1/0 O 180.40.7.65/32 [110/1] via 180.40.7.131, 00:21:54, FastEthernet0/0 C 180.40.7.64/27 is directly connected, Serial1/0 R3#sh ip oe sop  pf nei Neighbor ID Pri State Dead Time Address Interface 208.28.1.1 0 FULL/ - 00:01:49 180.40.7.65 Serial1/0 180.40.7.162 0 FULL/ - 00:01:49 180.40.7.67 Serial1/0 180.40.7.130 1 FULL/BDR 00:00:31 180.40.7.130 FastEthernet0/0 208.28.1.1 1 FULL/DR 00:00:31 180.40.7.131 FastEthernet0/0 R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.2 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 ms R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 48 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: disabled, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 54 message lines logged R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#logg buf R3(config)#^Z R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.2 sou 100.1.1.1sh ip route ping 20.10.1.2 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 49 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 1 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 55 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 18:51:20.029: %SYS-5-CONFIG_I: Configured from console by console R3# RACK8AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#shut R7(config-if)# *Mar 1 18:51:52.310: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/1 from 2WAY to DOWN, Neighbor Down: Interface down or detached *Mar 1 18:51:52.310: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.67, 00:00:26, Serial1/0 O 20.10.1.0 [110/782] via 180.40.7.67, 00:00:26, Serial1/0 O 208.28.1.0/24 [110/782] via 180.40.7.65, 00:00:26, Serial1/0 180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:00:26, Serial1/0 O 180.40.7.161/32 [110/781] via 180.40.7.65, 00:00:26, Serial1/0 O 180.40.7.67/32 [110/781] via 180.40.7.67, 00:00:27, Serial1/0 O 180.40.7.65/32 [110/781] via 180.40.7.65, 00:00:27, Serial1/0 C 180.40.7.64/27 is directly connected, Serial1/0 R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4# *Mar 1 18:54:52.167: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 180.40.0.0/27 is subnetted, 1 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 00:00:01, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.129, 00:00:01, FastEthernet0/0 O 208.28.1.0/24 [110/783] via 180.40.7.129, 00:00:01, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.161/32 [110/782] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.67/32 [110/782] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.66/32 [110/1] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:02, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Loopback0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/793] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 20.10.1.0 [110/783] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 208.28.1.0/24 [110/783] via 180.40.7.129, 00:00:05, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/782] via 180.40.7.129, 00:00:06, FastEthernet0/0 O 180.40.7.161/32 [110/782] via 180.40.7.129, 00:00:06, FastEthernet0/0 O 180.40.7.67/32 [110/782] via 180.40.7.129, 00:00:06, FastEthernet0/0 O 180.40.7.66/32 [110/1] via 180.40.7.129, 00:00:06, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:06, FastEthernet0/0 R4#sh ip routeping 20.10.1.2 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/62/64 ms R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Ma87: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy match *Mar 1 18:52:49.087: CEF-IP-POLICY: fib for address 180.40.7.67 is R3#with flag 0 *Mar 1 18:52:49.091: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match *Mar 1 18:52:49.091: IP: route map Prob1, item 20, permit *Mar 1 18:52:49.091: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed *Mar 1 18:52:49.091: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 *Mar 1 18:52:49.151: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy match *Mar 1 18:52:49.151: CEF-IP-POLICY: fib for address 180.40.7.67 is with flag 0 *Mar 1 18:52:49.155: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match *Mar 1 18:52:49.155: IP: route map Prob1, item 20, permit *Mar 1 18:52:49.155: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed *Mar 1 18:52:49.155: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 R3# R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.2 sou 100.1.1.1 sou 100.1.1.1 1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/61/64 ms R4# RACK8AS>4 3 [Resuming connection 3 to r3 ... ] * R3#sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 120 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 72 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 56 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 18:51:20.029: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 18:52:30.729: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired *Mar 1 18:52:48.894: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy match *Mar 1 18:52:48.894: CEF-IP-POLICY: fib for address 180.40.7.67 is with flag 0 *Mar 1 18:52:48.899: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match *Mar 1 18:52:48.899: IP: route map Prob1, item 20, permit *Mar 1 18:52:48.899: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed *Mar 1 18:52:48.899: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 *Mar 1 18:52:48.959: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy match *Mar 1 18:52:48.959: CEF-IP-POLICY: fib for address 180.40.7.67 is with flag 0 *Mar 1 18:52:48.963: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match *Mar 1 18:52:48.963: IP: route map Prob1, item 20, permit *Mar 1 18:52:48.963: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed --More--  *Mar 1 18:52:48.963: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 *Mar 1 18:52:49.023: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy match *Mar 1 18:52:49.023: CEF-IP-POLICY: fib for address 180.40.7.67 is with flag 0 *Mar 1 18:52:49.027: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match *Mar 1 18:52:49.027: IP: route map Prob1, item 20, permit *Mar 1 18:52:49.027: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed *Mar 1 18:52:49.027: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 *Mar 1 18:52:49.087: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy match *Mar 1 18:52:49.087: CEF-IP-POLICY: fib for address 180.40.7.67 is with flag 0 *Mar 1 18:52:49.091: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match *Mar 1 18:52:49.091: IP: route map Prob1, item 20, permit *Mar 1 18:52:49.091: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed *Mar 1 18:52:49.091: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 *Mar 1 18:52:49.151: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy match *Mar 1 18:52:49.151: CEF-IP-POLICY: fib for address 180.40.7.67 is with flag 0 *Mar 1 18:52:49.155: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match --More--  *Mar 1 18:52:49.155: IP: route map Prob1, item 20, permit *Mar 1 18:52:49.155: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed *Mar 1 18:52:49.155: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 *Mar 1 18:53:35.250: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.250: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:53:35.311: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.315: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:53:35.375: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.375: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:53:35.435: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.435: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:53:35.499: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.499: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding R3# sh route route-map Prob1, permit, sequence 10 Match clauses: ip address (access-lists): 102 length 1001 2147483647 Set clauses: interface Serial1/2 Policy routing matches: 0 packets, 0 bytes route-map Prob1, permit, sequence 20 Match clauses: ip address (access-lists): 100 Set clauses: ip next-hop 180.40.7.67 Policy routing matches: 5 packets, 570 bytes route-map Prob1, permit, sequence 30 Match clauses: ip address (access-lists): 101 Set clauses: interface Serial1/2 Policy routing matches: 5 packets, 570 bytes R3#sh access-list Extended IP access list 100 10 permit icmp host 100.1.1.1 host 20.10.1.2 echo (10 matches) Extended IP access list 101 10 permit icmp host 100.1.1.1 host 20.10.1.1 echo (5 matches) Extended IP access list 102 10 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo (15 matches) R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip cef R3(config)#^Z R3# *Mar 1 18:54:47.641: %SYS-5-CONFIG_I: Configured from console by console R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 RACK8AS>3 [Resuming connection 3 to r3 ... ] *.976: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:51.980: IP: route map Prob1, item 30, permit *Mar 1 18:54:51.980: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 18:54:51.980: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 R3# R3# *Mar 1 18:54:53.976: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:53.976: IP: route map Prob1, item 30, permit *Mar 1 18:54:53.976: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 18:54:53.976: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 R3# R3# R3# R3# *Mar 1 18:54:55.975: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:55.975: IP: route map Prob1, item 30, permit *Mar 1 18:54:55.975: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 18:54:55.979: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 R3# *Mar 1 18:54:57.974: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:57.974: IP: route map Prob1, item 30, permit *Mar 1 18:54:57.978: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 18:54:57.978: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 R3# *Mar 1 18:54:59.973: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:59.977: IP: route map Prob1, item 30, permit *Mar 1 18:54:59.977: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 18:54:59.977: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 R3#conmfi   fig t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip cef R3(config)# *Mar 1 18:55:17.771: PR-RP: Set FastEthernet0/0 policy_routemap=Prob1; cached_map=Prob1 *Mar 1 18:55:17.791: PR-RP: Set FastEthernet0/0 policy_routemap=Prob1; cached_map=Prob1 R3(config)#^Z R3# *Mar 1 18:55:40.191: %SYS-5-CONFIG_I: Configured from console by console R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] .. R4#ping 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/64 ms R4#x RACK8AS>3 [Resuming connection 3 to r3 ... ] * R3#swh     sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 179 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 131 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 58 message lines logged --More--   Log Buffer (4096 bytes): 1/0 180.40.7.67 *Mar 1 18:53:35.250: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.250: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:53:35.311: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.315: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:53:35.375: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.375: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:53:35.435: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.435: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:53:35.499: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:53:35.499: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding --More--  *Mar 1 18:54:47.641: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 18:54:51.976: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:51.980: IP: route map Prob1, item 30, permit *Mar 1 18:54:51.980: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 18:54:51.980: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 *Mar 1 18:54:53.976: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:53.976: IP: route map Prob1, item 30, permit *Mar 1 18:54:53.976: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 18:54:53.976: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 *Mar 1 18:54:55.975: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:55.975: IP: route map Prob1, item 30, permit *Mar 1 18:54:55.975: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 18:54:55.979: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 *Mar 1 18:54:57.974: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:57.974: IP: route map Prob1, item 30, permit *Mar 1 18:54:57.978: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed --More--  *Mar 1 18:54:57.978: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 *Mar 1 18:54:59.973: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, policy match *Mar 1 18:54:59.977: IP: route map Prob1, item 30, permit *Mar 1 18:54:59.977: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, policy routed *Mar 1 18:54:59.977: IP: FastEthernet0/0 to Serial1/2 20.10.1.1 *Mar 1 18:55:17.771: PR-RP: Set FastEthernet0/0 policy_routemap=Prob1; cached_map=Prob1 *Mar 1 18:55:17.791: PR-RP: Set FastEthernet0/0 policy_routemap=Prob1; cached_map=Prob1 *Mar 1 18:55:40.191: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 18:55:44.879: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:55:44.883: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:55:44.943: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:55:44.943: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:55:45.003: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:55:45.007: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding --More--  *Mar 1 18:55:45.067: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:55:45.067: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding *Mar 1 18:55:45.127: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 18:55:45.127: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy rejected - normal forwarding R3# sh deb Policy Routing: Policy routing debugging is on R3#clea logg Clear logging buffer [confirm] R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] % Ambiguous command: "x" R4#xping 20.10.1.1 sou 100.1.1.12 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 64/64/64 ms R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Mflag 0 *Mar 1 18:57:01.356: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 100, policy match *Mar 1 18:57:01.356: IP: route map Prob1, item 20, permit *Mar 1 18:57:01.356: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/0), len 100, policy routed *Mar 1 18:57:01.360: IP: FastEthernet0/0 to Serial1/0 180.40.7.67 R3# R3#sh ip ospf int s 1/0 Serial1/0 is up, line protocol is up Internet Address 180.40.7.66/27, Area 0 Process ID 1, Router ID 180.40.7.129, Network Type POINT_TO_MULTIPOINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT, Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 oob-resync timeout 120 Hello due in 00:00:02 Index 2/2, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 2 Last flood scan time is 0 msec, maximum is 4 msec Neighbor Count is 2, Adjacent neighbor count is 2 Adjacent with neighbor 208.28.1.1 Adjacent with neighbor 180.40.7.162 Suppress hello for 0 neighbor(s) R3#sh ip ospf int s 1/0 2 Serial1/2 is up, line protocol is down Internet Address 180.40.7.1/27, Area 0 Process ID 1, Router ID 180.40.7.129, Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State DOWN, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 R3# RACK8AS>2 [Resuming connection 2 to r2 ... ] R2#sh % Type "show ?" for a list of subcommands R2# R2#sh inht s 1/       t 1/2 ^ % Invalid input detected at '^' marker. R2#sh int s 1/2 Serial1/2 is up, line protocol is down Hardware is CD2430 in sync mode Internet address is 180.40.7.2/27 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input never, output 00:00:07, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 7329 packets output, 223340 bytes, 0 underruns 0 output errors, 0 collisions, 2422 interface resets 0 output buffer failures, 0 output buffers swapped out --More--   R2#sh run int clock       s 1/2 Building configuration... Current configuration : 66 bytes ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 end R2#sh control s 1/2 CD2430 Slot 1, Port 2, Controller 0, Channel 2, Revision 19 Channel mode is synchronous serial idb 0x83794468, buffer size 1524, V.35 DCE cable Global registers rpilr 0x2, rir 0x0, risr 0x0, rfoc 0x0, rdr 0x0 tpilr 0x1, tir 0x2, tisr 0x68, tftc 0x0, tdr 0x0 mpilr 0x3, mir 0x2, misr 0x60 bercnt 0xFF, stk 0x0 Per-channel registers for channel 2 Option registers 0x02 0x00 0x42 0x67 0x60 0x00 0x00 Command and status registers cmr 0xC0, ccr 0x00, csr 0x8C, msvr-rts 0xE1, msvr-dtr 0xE1 Clock option registers rcor 0x80, rbpr 0x81, tcor 0x00, tbpr 0x81 Interrupt registers ier 0x89, livr 0x08, licr 0x08 DMA buffer status 0x20 DMA receive registers arbaddr 0x7DE7E44, arbcnt 1548, arbsts 0x1 brbaddr 0x7DE77C4, brbcnt 1548, brbsts 0x1 rcbaddr 0x0 --More--   R2#q config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#clock rate 128000 R2(config-if)#^Z R2# *Mar 1 18:59:41.319: %SYS-5-CONFIG_I: Configured from console by console R2#sh int s /\ 1 ~  1/2 Serial1/2 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is 180.40.7.2/27 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input 00:00:08, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 5 packets input, 1193 bytes, 0 no buffer Received 4 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 7336 packets output, 223508 bytes, 0 underruns 0 output errors, 0 collisions, 2424 interface resets 0 output buffer failures, 0 output buffers swapped out --More-- *Mar 1 18:59:53.398: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up *Mar 1 18:59:53.883: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from LOADING to FULL, Loading Done --More--   R2# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:00:03, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.67, 00:00:03, Serial1/0 [110/792] via 180.40.7.2, 00:00:03, Serial1/2 O 20.10.1.0 [110/782] via 180.40.7.67, 00:00:03, Serial1/0 [110/782] via 180.40.7.2, 00:00:03, Serial1/2 O 208.28.1.0/24 [110/782] via 180.40.7.65, 00:00:03, Serial1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:00:04, Serial1/0 [110/781] via 180.40.7.2, 00:00:04, Serial1/2 O 180.40.7.161/32 [110/781] via 180.40.7.65, 00:00:04, Serial1/0 --More--   R3#sh    clea log Clear logging buffer [confirm] R3#sh cef % Incomplete command. R3#sh ip cef Prefix Next Hop Interface 0.0.0.0/0 drop Null0 (default route handler entry) 0.0.0.0/32 receive 20.10.1.0/24 180.40.7.67 Serial1/0 180.40.7.2 Serial1/2 20.10.2.0/24 180.40.7.67 Serial1/0 180.40.7.2 Serial1/2 100.1.1.1/32 180.40.7.130 FastEthernet0/0 180.40.7.0/27 attached Serial1/2 180.40.7.0/32 receive 180.40.7.1/32 receive 180.40.7.31/32 receive 180.40.7.64/27 attached Serial1/0 180.40.7.64/32 receive 180.40.7.65/32 180.40.7.65 Serial1/0 180.40.7.66/32 receive 180.40.7.67/32 180.40.7.67 Serial1/0 180.40.7.2 Serial1/2 180.40.7.95/32 receive 180.40.7.128/27 attached FastEthernet0/0 180.40.7.128/32 receive 180.40.7.129/32 receive 180.40.7.130/32 180.40.7.130 FastEthernet0/0 --More--   R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.2 sou 100.1.1.1x ping 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/18/20 ms R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Mted *Mar 1 19:00:27.194: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 19:00:27.194: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed R3# R3# R3# R3# R3# R3# R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#piong   ng ip Target IP address: 20.10.1.2 Repeat count [5]: Datagram size [100]: 1499 Timeout in seconds [2]: Extended commands [n]: y Source address or interface: 100.1.1.1 Type of service [0]: Set DF bit in IP header? [no]: Validate reply data? [no]: Data pattern [0xABCD]: Loose, Strict, Record, Timestamp, Verbose[none]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 5, 1499-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 196/196/196 ms R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] *M), len 1499, FIB policy routed R3# R3# *Mar 1 19:01:35.454: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1499, FIB policy match *Mar 1 19:01:35.454: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1499, FIB policy routed *Mar 1 19:01:35.650: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1499, FIB policy match *Mar 1 19:01:35.650: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1499, FIB policy routed R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#ping 20.10.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/17/20 ms R4# R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 291 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 243 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 60 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 19:00:27.118: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 19:00:27.118: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed *Mar 1 19:00:27.138: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 19:00:27.138: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed *Mar 1 19:00:27.158: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 19:00:27.158: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed *Mar 1 19:00:27.174: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 19:00:27.178: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed *Mar 1 19:00:27.194: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1, len 100, FIB policy match *Mar 1 19:00:27.194: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.1 (Serial1/2), len 100, FIB policy routed --More--  *Mar 1 19:01:34.861: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1499, FIB policy match *Mar 1 19:01:34.861: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1499, FIB policy routed *Mar 1 19:01:35.061: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1499, FIB policy match *Mar 1 19:01:35.061: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1499, FIB policy routed *Mar 1 19:01:35.257: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1499, FIB policy match *Mar 1 19:01:35.257: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1499, FIB policy routed *Mar 1 19:01:35.454: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1499, FIB policy match *Mar 1 19:01:35.454: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1499, FIB policy routed *Mar 1 19:01:35.650: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2, len 1499, FIB policy match *Mar 1 19:01:35.650: IP: s=100.1.1.1 (FastEthernet0/0), d=20.10.1.2 (Serial1/2), len 1499, FIB policy routed *Mar 1 19:02:08.187: IP: s=180.40.7.130 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy rejected(no match) - normal forwarding *Mar 1 19:02:08.207: IP: s=180.40.7.130 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy rejected(no match) - normal forwarding --More--  *Mar 1 19:02:08.227: IP: s=180.40.7.130 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy rejected(no match) - normal forwarding *Mar 1 19:02:08.243: IP: s=180.40.7.130 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy rejected(no match) - normal forwarding *Mar 1 19:02:08.263: IP: s=180.40.7.130 (FastEthernet0/0), d=20.10.1.2, len 100, FIB policy rejected(no match) - normal forwarding R3#    sh run | b interface Faster thernet1 /0 R3#sh run | b interface Fastethernet/0log run | b interface Fastethernet/00/0 R3#sh run | b interface Fastethernet0/0thernet0/0 Ethernet0/0 interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast frame-relay map ip 180.40.7.67 302 broadcast ! --More--  interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! --More--  interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo ! route-map Prob1 permit 10 match ip address 102 match length 1001 2147483647 set interface Serial1/2 ! route-map Prob1 permit 20 --More--   match ip address 100 set ip next-hop 180.40.7.67 ! route-map Prob1 permit 30 match ip address 101 set interface Serial1/2 ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! --More--   R3# RACK8AS>7 [Resuming connection 7 to r7 ... ] *M R7(config-if)#no shut R7(config-if)#^Z R7# *Mar 1 19:19:06.769: %SYS-5-CONFIG_I: Configured from console by console R7# *Mar 1 19:19:08.452: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Mar 1 19:19:09.453: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R7# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#sh access-list R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#access-list 100 icmp any any ech *Mar 1 19:22:14.775: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config)#access-list 100 icmp any any echo ^ % Invalid input detected at '^' marker. R4(config)#access-list 100 icmp any any echopicmp any any echoeicmp any any echoricmp any any echo icmp any any echo R4(config)#access-list 100 per icmp any any echo   R4(config)#access-list 100 per icmp any any echo-r R4(config)#access-list 100 per icmp any any echo-reply R4(config)#route-map Prob2 R4(config-route-map)#match ip add 100 R4(config-route-map)#set ip h ne R4(config-route-map)#set ip next-hop 180.40.7.129 R4(config-route-map)#exit R4(config)#ip lo R4(config)#ip local ? policy Enable policy routing pool IP Local address pool lists R4(config)#ip local po R4(config)#ip local pol R4(config)#ip local policy ? route-map Policy route map R4(config)#ip local policy route R4(config)#ip local policy route-map Prob2                               no route-map Prob2 R4(config)#no route-map Prob2 3no route-map Prob3  route-map Prob3  R4(config-route-map)# route-map Prob3no route-map Prob2exit set ip next-hop 180.40.7.129 R4(config-route-map)#set ip next-hop 180.40.7.129 route-map Prob3 no route-map Prob2exit set ip next-hop 180.40.7.129match ip add 100  R4(config-route-map)#ip local pol route Prob3 R4(config)#^Z R4# *Mar 1 19:25:26.155: %SYS-5-CONFIG_I: Configured from console by console R4#deb ip pol Policy routing debugging is on R4#pindeb ip polconfig t sh access-listping 20.10.1.2100.1.1.1 y 149920.10.1.2ping ip 20.10.1.1 sou 100.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 20.10.1.1, timeout is 2 seconds: Packet sent with a source address of 100.1.1.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 20/20/24 ms R4# *Mar 1 19:25:38.243: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100, policy match *Mar 1 19:25:38.243: IP: route map Prob3, item 10, permit *Mar 1 19:25:38.243: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 19:25:38.243: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 19:25:38.263: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100, policy match *Mar 1 19:25:38.263: IP: route map Prob3, item 10, permit *Mar 1 19:25:38.263: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 19:25:38.263: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 19:25:38.283: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100, policy match *Mar 1 19:25:38.287: IP: route map Prob3, item 10, permit *Mar 1 19:25:38.287: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 19:25:38.287: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 19:25:38.307: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100 R4#, policy match *Mar 1 19:25:38.307: IP: route map Prob3, item 10, permit *Mar 1 19:25:38.307: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 19:25:38.307: IP: local to FastEthernet0/0 180.40.7.129 *Mar 1 19:25:38.327: IP: s=100.1.1.1 (local), d=20.10.1.1, len 100, policy match *Mar 1 19:25:38.327: IP: route map Prob3, item 10, permit *Mar 1 19:25:38.331: IP: s=100.1.1.1 (local), d=20.10.1.1 (FastEthernet0/0), len 100, policy routed *Mar 1 19:25:38.331: IP: local to FastEthernet0/0 180.40.7.129 R4#tr R4#traceroute 20.10.1.1 Type escape sequence to abort. Tracing the route to 20.10.1.1 1 180.40.7.129 4 msec 180.40.7.131 4 msec 180.40.7.129 4 msec 2 180.40.7.162 32 msec 180.40.7.2 24 msec *Mar 1 19:26:05.331: IP: s=180.40.7.130 (local), d=20.10.1.1, len 28, policy rejected -- normal forwarding *Mar 1 19:26:05.335: IP: s=180.40.7.130 (local), d=20.10.1.1, len 28, policy rejected -- normal forwarding *Mar 1 19:26:05.339: IP: s=180.40.7.130 (local), d=20.10.1.1, len 28, policy rejected -- normal forwarding *Mar 1 19:26:05.343: IP: s=180.40.7.130 (local), d=20.10.1.1, len 28, policy rejected -- normal forwarding *Mar 1 19:26:05.375: IP: s=180.40.7.130 (local), d=20.10.1.1, len 28, policy rejected -- normal forwarding *Mar 1 19:26:05.403: IP: s=180.40.7.130 (local), d=20.10.1.1, len 28, policy rejected -- normal forwarding * R4#sh run  | b ip local ip local policy route-map Prob3 no ip http server no ip http secure-server ip classless ! ! access-list 100 permit icmp any any echo access-list 100 permit icmp any any echo-reply ! route-map Prob3 permit 10 match ip address 100 set ip next-hop 180.40.7.129 ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 --More--   R4# R4# RACK8AS>2 [Resuming connection 2 to r2 ... ] R2#sh access-list R2#dpla[spdlf[asplfd[pasldf[paldf~                               config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.2 R2(config-subif)#tr R2(config-subif)#traffic-shape ? adaptive Enable Traffic Shaping adaptation to BECN fecn-adapt Enable Traffic Shaping reflection of FECN as BECN group configure token bucket: group CIR (bps) [Bc (bits) [Be (bits)]] rate configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]] R2(config-subif)#traffic-shape ratew    ? <8000-100000000> Target Bit Rate (bits per second) R2(config-subif)#traffic-shape rate 64000 ? <0-100000000> bits per interval, sustained R2(config-subif)#traffic-shape rate 64000 64000 ? <0-100000000> bits per interval, excess in first interval R2(config-subif)#traffic-shape rate 64000 64000 32000 ? <0-4096> Set buffer limit R2(config-subif)#traffic-shape rate 64000 64000 32000 R2(config-subif)#tr R2(config-subif)#traffic-shape ad R2(config-subif)#traffic-shape adaptive ? <1-100000000> Lower Bound Target Bit Rate (bits per second) R2(config-subif)#traffic-shape adaptive 43  32000 ? R2(config-subif)#traffic-shape adaptive 32000 R2(config-subif)#exit R2(config)#map R2(config)#map-c R2(config)#map-class  fr R2(config)#map-class frame-relay test R2(config-map-class)#fram ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 7000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R2(config-map-class)#fram      exit R2(config)#nexitmap-class frame-relay test nmap-class frame-relay test omap-class frame-relay test  map-class frame-relay test  R2(config)#access-list 100   1 per ospf any anyr ospf any any  ospf any any  ospf any any d ospf any anye ospf any anyn ospf any anyy ospf any any R2(config)#access-list 101 per ip[    any any R2(config)#fram R2(config)#frame-relay de` R2(config)#frame-relay de`  R2(config)#frame-relay de-list ? <1-10> DE list numbers R2(config)#frame-relay de-list 1 ? interface Identify packets from a named interface protocol Identify packets by protocol R2(config)#frame-relay de-list 1 pro R2(config)#frame-relay de-list 1 protocol ? appletalk AppleTalk arp IP ARP bridge Bridging clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System compressedtcp Compressed TCP decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 ip IP ipx Novell IPX R2(config)#frame-relay de-list 1 protocol ipo    ? fragments Classify fragmented IP packets gt Identify packets greater than a specified size list To specify an access list lt Identify packets less than a specified size tcp Classify TCP packets 'to' or 'from' the specified port udp Classify UDP packets 'to' or 'from' the specified port R2(config)#frame-relay de-list 1 protocol ip li R2(config)#frame-relay de-list 1 protocol ip list ? <1-199> IP access list <1300-2699> IP access list R2(config)#frame-relay de-list 1 protocol ip list 101 R2(config)#int s 1. /0.2 R2(config-subif)#fram R2(config-subif)#frame-relay ? class Define a map class on the interface de-group Associate a DE group with a DLCI interface-dlci Define a DLCI on an interface/subinterface inverse-arp Enable/disable FR inverse ARP ip Frame Relay Internet Protocol config commands map Map a protocol address to a DLCI address payload-compression Use payload compression priority-dlci-group Define a priority group of DLCIs vc-bundle configure a frame-relay vc-bundle R2(config-subif)#frame-relay de R2(config-subif)#frame-relay de-group ? <1-10> DE group number R2(config-subif)#frame-relay de-group 1 ? <16-1007> DLCI value R2(config-subif)#frame-relay de-group 1 207 ? R2(config-subif)#frame-relay de-group 1 207 R2(config-subif)#^Z R2#sg  *Mar 1 19:50:36.916: %SYS-5-CONFIG_I: Configured from console by console R2#sh tra R2#sh traf R2#sh traffic-shape ser 1/2 0.2 Interface Se1/0.2 Access Target Byte Sustain Excess Interval Increment Adapt VC List Rate Limit bits/int bits/int (ms) (bytes) Active - 64000 12000 64000 32000 1000 8000 BECN R2# R2# R2# R2# R2# R2#sh run | b interface Serial  1/0 interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 64000 32000 1000 traffic-shape adaptive 32000 frame-relay de-group 1 207 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 --More--   clock rate 128000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 --More--   log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 101 deny ospf any any access-list 101 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 --More--   R2#sh run | b fram frame-relay de-list 1 protocol ip list 101 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address --More--   shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ip address 180.40.7.67 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point --More--   ip address 180.40.7.162 255.255.255.224 ip ospf network point-to-multipoint traffic-shape rate 64000 64000 32000 1000 traffic-shape adaptive 32000 frame-relay de-group 1 207 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 clock rate 128000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! --More--  interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 101 deny ospf any any access-list 101 permit ip any any --More--  ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R2# R2# RACK8AS>3 [Resuming connection 3 to r3 ... ] * R3#wr Building configuration... [OK] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ip tcp ? adjust-mss Adjust the mss of transit packets compression-connections Maximum number of compressed connections header-compression Enable TCP header compression R3(config-if)#ip tcp he R3(config-if)#ip tcp header-compression ? passive Compress only for destinations which send compressed headers R3(config-if)#ip tcp header-compression                           fram   R3(config-if)#frame-relay map IP    ip ? A.B.C.D Protocol specific address R3(config-if)#frame-relay map ip                    do sh run int s 1/0 Building configuration... Current configuration : 223 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast frame-relay map ip 180.40.7.67 302 broadcast end R3(config-if)#frame-relay map ip 180.40.7.65 307 ? broadcast Broadcasts should be forwarded to this address cisco Use CISCO Encapsulation compress Enable TCP/IP and RTP/IP header compression ietf Use RFC1490/RFC2427 Encapsulation nocompress Do not compress TCP/IP headers payload-compression Use payload compression rtp RTP header compression parameters tcp TCP header compression parameters R3(config-if)#frame-relay map ip 180.40.7.65 307 br R3(config-if)#frame-relay map ip 180.40.7.65 307 broadcast ? cisco Use CISCO Encapsulation compress Enable TCP/IP and RTP/IP header compression ietf Use RFC1490/RFC2427 Encapsulation nocompress Do not compress TCP/IP headers payload-compression Use payload compression rtp RTP header compression parameters tcp TCP header compression parameters R3(config-if)#frame-relay map ip 180.40.7.65 307 broadcast co R3(config-if)#frame-relay map ip 180.40.7.65 307 broadcast compress          tcp ? header-compression Enable TCP/IP header compression R3(config-if)#frame-relay map ip 180.40.7.65 307 broadcast tcp h R3(config-if)#$ map ip 180.40.7.65 307 broadcast tcp header-compression ? active Always compress TCP/IP headers connections Maximum number of compressed TCP connections passive Compress for destinations sending compressed headers R3(config-if)#$ map ip 180.40.7.65 307 broadcast tcp header-compression con R3(config-if)#$0.40.7.65 307 broadcast tcp header-compression connections ? <3-256> Number of TCP connections R3(config-if)#$0.40.7.65 307 broadcast tcp header-compression connections 20 R3(config-if)#$0.40.7.65 307 broadcast tcp header-compression connections 20 $0.40.7.65 307 broadcast tcp header-compression connections 20 R3(config-if)#$0.40.7.65 307 broadcast tcp header-compression connections 20do sh run int s 1/0  Building configuration... Current configuration : 261 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast end R3(config-if)#end R3#x *Mar 1 19:57:25.922: %SYS-5-CONFIG_I: Configured from console by console R3#x RACK8AS>7 [Resuming connection 7 to r7 ... ] *M R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 0/0.1 ^ % Invalid input detected at '^' marker. R7(config)#int s 0/0.1/0.1 1/0.1 R7(config-subif)# RACK8AS>3 [Resuming connection 3 to r3 ... ] % Ambiguous command: "x" R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int   int s fa 0/0 R3(config-if)#shut R3(config-if)# *Mar 1 19:59:58.140: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 19:59:58.140: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)#^Z R3# *Mar 1 19:59:59.991: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 20:00:00.135: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down R3#te *Mar 1 20:00:01.136: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R3#te  180.40.7.65 Trying 180.40.7.65 ... Open R3#disc Closing connection to 180.40.7.65 [confirm] R3#deb ip pack IP packet debugging is on R3#deb ip packisc 180.40.7.65 Trying 180.40.7.65 ... Open *Mar 1 20:00:43.133: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:43.133: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 44, sending *Mar 1 20:00:43.165: IP: tableid=0, s=180.40.7.65 (Serial1/0), d=180.40.7.66 (Serial1/0), routed via RIB *Mar 1 20:00:43.165: IP: s=180.40.7.65 (Serial1/0), d=180.40.7.66 (Serial1/0), len 44, rcvd 3 *Mar 1 20:00:43.169: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:43.169: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 40, sending *Mar 1 20:00:43.169: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:43.169: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 52, sending *Mar 1 20:00:43.173: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:43.173: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 40, sending *Mar 1 20:00:43.262: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:00:43.887: IP: s=180.40.7.1 (local), d=224.0.0.5 (Serial1/2), len 80, sending broad/multicast *Mar 1 20:00:45.012: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:45.012: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 52, sending *Mar 1 20:00:45.169: IP: tableid=0, s=180.40.7.65 (Serial1/0), d=180.40.7.66 (Serial1/0), routed via RIB *Mar 1 20:00:45.169: IP: s=180.40.7.65 (Serial1/0), d=180.40.7.66 (Serial1/0), len 44, rcvd 3 *Mar 1 20:00:45.169: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:45.169: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 40, sending *Mar 1 20:00:48.686: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:48.686: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 52, sending *Mar 1 20:00:49.171: IP: tableid=0, s=180.40.7.65 (Serial1/0), d=180.40.7.66 (Serial1/0), routed via RIB *Mar 1 20:00:49.171: IP: s=180.40.7.65 (Serial1/0), d=180.40.7.66 (Serial1/0), len 44, rcvd 3 *Mar 1 20:00:49.171: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:49.171: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 40, sending *Mar 1 20:00:53.262: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:00:53.887: IP: s=180.40.7.1 (local), d=224.0.0.5 (Serial1/2), len 80, sending broad/multicast *Mar 1 20:00:56.034: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:56.034: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 52, sending *Mar 1 20:00:56.255: IP: s=180.40.7.65 (Serial1/0), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:00:56.748: IP: s=180.40.7.67 (Serial1/0), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:00:57.172: IP: tableid=0, s=180.40.7.65 (Serial1/0), d=180.40.7.66 (Serial1/0), routed via RIB *Mar 1 20:00:57.172: IP: s=180.40.7.65 (Serial1/0), d=180.40.7.66 (Serial1/0), len 44, rcvd 3 *Mar 1 20:00:57.172: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:00:57.172: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 40, sending *Mar 1 20:00:58.062: IP: s=180.40.7.66 (local), d=224.0.0.5 (Serial1/0), len 84, sending broad/multicast *Mar 1 20:01:03.262: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:01:03.887: IP: s=180.40.7.1 (local), d=224.0.0.5 (Serial1/2), len 80, sending broad/multicast *Mar 1 20:01:10.731: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:10.731: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 52, sending *Mar 1 20:01:13.263: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:01:13.888: IP: s=180.40.7.1 (local), d=224.0.0.5 (Serial1/2), len 80, sending broad/multicastu all *Mar 1 20:01:17.950: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:17.950: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:18.047: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:18.047: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:18.167: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:18.167: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:18.279: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:18.283: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:18.447: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:18.447: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:18.708: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:18.708: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:01:23.263: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:01:23.888: IP: s=180.40.7.1 (local), d=224.0.0.5 (Serial1/2), len 80, sending broad/multicast *Mar 1 20:01:26.304: IP: s=180.40.7.65 (Serial1/0), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:01:26.801: IP: s=180.40.7.67 (Serial1/0), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:01:28.063: IP: s=180.40.7.66 (local), d=224.0.0.5 (Serial1/0), len 84, sending broad/multicastu all *Mar 1 20:01:30.599: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:30.599: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:30.715: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:30.715: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:30.844: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:30.844: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:31.000: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:31.000: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:31.152: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:31.152: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 41, sending *Mar 1 20:01:31.360: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:31.360: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:01:33.263: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:01:33.889: IP: s=180.40.7.1 (local), d=224.0.0.5 (Serial1/2), len 80, sending broad/multicast *Mar 1 20:01:40.123: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:40.123: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 66, sending *Mar 1 20:01:43.264: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0 *Mar 1 20:01:43.889: IP: s=180.40.7.1 (local), d=224.0.0.5 (Serial1/2), len 80, sending broad/multicast^[[A *Mar 1 20:01:45.203: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:45.207: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 43, sending *Mar 1 20:01:45.215: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:45.215: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:01:45.367: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:45.367: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:01:46.325: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:46.325: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:01:46.501: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:46.501: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:01:46.661: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:46.661: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:01:46.814: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:46.814: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending R3# *Mar 1 20:01:48.789: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:01:48.789: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 40, sending R3#u all All possible debugging has been turned off R3#deb ip pack de IP packet debugging is on (detailed) R3# [Resuming connection 1 to 180.40.7.65 ... ] *Mar 1 20:02:51.940: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:51.940: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 40, sending *Mar 1 20:02:51.940: TCP src=30258, dst=23, seq=609010638, ack=4035928424, win=4128 ACK *Mar 1 20:02:52.882: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:52.882: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:52.882: TCP src=30258, dst=23, seq=609010638, ack=4035928424, win=4128 ACK PSH *Mar 1 20:02:53.195: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:53.195: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:53.199: TCP src=30258, dst=23, seq=609010640, ack=4035928424, win=4128 ACK PSH *Mar 1 20:02:53.267: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 20:02:53.375: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:53.375: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:53.375: TCP src=30258, dst=23, seq=609010642, ack=4035928424, win=4128 ACK PSH *Mar 1 20:02:53.531: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:53.535: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:53.535: TCP src=30258, dst=23, seq=609010644, ack=4035928424, win=4128 ACK PSH *Mar 1 20:02:53.892: IP: s=180.40.7.1 (local), d=224.0.0.5 (Serial1/2), len 80, sending broad/multicast, proto=89 RACK8AS> [Resuming connection 3 to r3 ... ] *Mar R3# *Mar 1 20:02:59.597: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:59.597: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:59.597: TCP src=30258, dst=23, seq=609010646, ack=4035928424, win=4128 ACK PSH R3#u a *Mar 1 20:03:00.987: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:03:00.991: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 40, sending *Mar 1 20:03:00.991: TCP src=30258, dst=23, seq=609010648, ack=4035928424, win=4128 ACK R3#u all All possible debugging has been turned off R3#disc Closing connection to 180.40.7.65 [confirm] R3# RACK8AS>7 [Resuming connection 7 to r7 ... ] * R7(config-subif)#fram ? class Define a map class on the interface de-group Associate a DE group with a DLCI interface-dlci Define a DLCI on an interface/subinterface inverse-arp Enable/disable FR inverse ARP ip Frame Relay Internet Protocol config commands map Map a protocol address to a DLCI address payload-compression Use payload compression priority-dlci-group Define a priority group of DLCIs vc-bundle configure a frame-relay vc-bundle R7(config-subif)#fram ip ? rtp RTP header compression parameters tcp TCP header compression parameters R7(config-subif)#fram ip tvcp     cp             do wr Building configuration... [OK] R7(config-subif)#fram ip tcp ? compression-connections Maximum number of compressed TCP connections header-compression Enable TCP/IP header compression R7(config-subif)#fram ip tcp h R7(config-subif)#fram ip tcp header-compression ? passive Compress for destinations sending compressed headers R7(config-subif)#fram ip tcp header-compression                    con R7(config-subif)#fram ip tcp con m R7(config-subif)#fram ip tcp compression-connections ? <3-256> Number of TCP connections R7(config-subif)#fram ip tcp compression-connections 20 Interface Serial1/0.1 not configured for TCP header compression R7(config-subif)#fram ip tcp compression-connections 20do wr fram ip tcp compression-connections 20                          he R7(config-subif)#fram ip tcp header-compression R7(config-subif)#fram ip tcp header-compression compression-connections 20 R7(config-subif)#do sh run           ^Z R7# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/0 Building configuration... Current configuration : 261 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast end R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#fram ip ? rtp RTP header compression parameters tcp TCP header compression parameters R3(config-if)#fram ip tcp ? compression-connections Maximum number of compressed TCP connections header-compression Enable TCP/IP header compression R3(config-if)#fram ip tcp             ^Z R3# *Mar 1 20:06:43.720: %SYS-5-CONFIG_I: Configured from console by console R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#no hs  shut R3(config-if)#^Z R3# *Mar 1 20:08:07.858: %SYS-5-CONFIG_I: Configured from console by console R3#sh *Mar 1 20:08:09.357: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 20:08:10.358: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3#sh run int s 1/0 Building configuration... Current configuration : 261 bytes ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast end R3# RACK8AS>7 [Resuming connection 7 to r7 ... ] * R7#sh run inr    t   nt s 1/0.1 Building configuration... Current configuration : 242 bytes ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 703 frame-relay ip tcp header-compression frame-relay ip tcp compression-connections 20 end R7# R7# *Mar 1 20:08:54.703: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/1 from LOADING to FULL, Loading Done R7# RACK8AS>3 [Resuming connection 3 to r3 ... ] * R3#sh run int s 1/0config t sh run int s 1/0disc u alldeb ip pack deu all 180.40.7.65 Trying 180.40.7.65 ... Open R7# R7# R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#^Z R7#^x  x  R3# [Resuming connection 1 to 180.40.7.65 ... ] R7# RACK8AS> [Resuming connection 3 to r3 ... ] R7# R7# R3#disc Closing connection to 180.40.7.65 [confirm] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s   f 0/0 R3(config-if)#shut R3(config-if)#^Z R3#config tdisc 180.40.7.65 *Mar 1 20:10:39.791: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 20:10:39.791: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 20:10:40.152: %SYS-5-CONFIG_I: Configured from console by console R3#180.40.7.65 Trying 180.40.7.65 ... *Mar 1 20:10:41.791: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 1 20:10:42.792: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to downOpen R7# R7# R7# R7# R7# R7#q [Connection to 180.40.7.65 closed by foreign host] R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#no shut R3(config-if)#^Z R3# *Mar 1 20:11:22.541: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 20:11:23.683: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 20:11:24.685: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3# *Mar 1 20:12:09.691: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 20:12:09.699: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3# RACK8AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#access-list 1 pre    er host 208.28.1.2 R7(config)#class-map R7(config)#class-map S5Telnet R7(config-cmap)#match ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R7(config-cmap)#match acc R7(config-cmap)#match access-group 1 R7(config-cmap)#mat R7(config-cmap)#match pr R7(config-cmap)#match pro R7(config-cmap)#match protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 --More--   custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching (Direct encapsulation only) dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) --More--   ipsec IP Security Protocol (ESP/AH) ipv6 IPV6 ipx Novell IPX irc Internet Relay Chat kazaa2 Kazaa Version 2 kerberos Kerberos l2tp L2F/L2TP tunnel ldap Lightweight Directory Access Protocol llc2 llc2 napster Napster Traffic netbios NetBIOS netshow Microsoft Netshow nfs Network File System nntp Network News Transfer Protocol notes Lotus Notes(R) novadigm Novadigm EDM ntp Network Time Protocol pad PAD links pcanywhere Symantec pcANYWHERE pop3 Post Office Protocol pppoe PPP over Ethernet pptp Point-to-Point Tunneling Protocol printer print spooler/lpd --More--   qllc qllc protocol rcmd BSD r-commands (rsh, rlogin, rexec) rip Routing Information Protocol rsrb Remote Source-Route Bridging rsvp Resource Reservation Protocol rtp Real Time Protocol rtspplayer RTSP players streaming protocol secure-ftp FTP over TLS/SSL secure-http Secured HTTP secure-imap Internet Message Access Protocol over TLS/SSL secure-irc Internet Relay Chat over TLS/SSL secure-ldap Lightweight Directory Access Protocol over TLS/SSL secure-nntp Network News Transfer Protocol over TLS/SSL secure-pop3 Post Office Protocol over TLS/SSL secure-telnet Telnet over TLS/SSL smtp Simple Mail Transfer Protocol snapshot Snapshot routing support snmp Simple Network Management Protocol socks SOCKS sqlnet SQL*NET for Oracle sqlserver MS SQL Server ssh Secured Shell streamwork Xing Technology StreamWorks player --More--   stun Serial Tunnel sunrpc Sun RPC syslog System Logging Utility telnet Telnet tftp Trivial File Transfer Protocol vdolive VDOLive streaming video vofr voice over Frame Relay packets xwindows X-Windows remote access R7(config-cmap)#match protocol telnet R7(config-cmap)#exit R7(config)#class-map S5Other R7(config-cmap)#match acc R7(config-cmap)#match access-group 1 R7(config-cmap)#exit R7(config)#class-map ma R7(config)#class-map match-any R7(config)#class-map match-any JPEG R7(config-cmap)#mat R7(config-cmap)#match pro R7(config-cmap)#match protocol ht R7(config-cmap)#match protocol http mim ? WORD Enter a string as the sub-protocol parameter R7(config-cmap)#match protocol http mim "*jpeg" R7(config-cmap)# match protocol http url *.jpeg R7(config-cmap)# match protocol http url *.jpg R7(config-cmap)# match protocol http url *.jpe R7(config-cmap)#exit R7(config)#pol R7(config)#policy-map Prob6 R7(config-pmap)#class R7(config-pmap)#class S5YT  Telnet R7(config-pmap-c)#ba R7(config-pmap-c)#bandwidth ? <8-2000000> Kilo Bits per second percent % of total Bandwidth remaining % of the remaining bandwidth R7(config-pmap-c)#bandwidth 1000 R7(config-pmap-c)#exit R7(config-pmap)#class R7(config-pmap)#class S5Other R7(config-pmap-c)#pol R7(config-pmap-c)#police ? <8000-2000000000> Bits per second cir Committed information rate R7(config-pmap-c)#police 5000000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 5000000 ? <1000-512000000> Burst bytes bc Conform burst conform-action action when rate is less than conform burst pir Peak Information Rate R7(config-pmap-c)#police 5000000 con R7(config-pmap-c)#police 5000000 conform-action ? drop drop packet exceed-action action when rate is within conform and conform + exceed burst set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#police 5000000 conform-action se R7(config-pmap-c)#police 5000000 conform-action set-p R7(config-pmap-c)#police 5000000 conform-action set-prec-transmit ? <0-7> new precedence R7(config-pmap-c)#police 5000000 conform-action set-prec-transmit 3 ? exceed-action action when rate is within conform and conform + exceed burst R7(config-pmap-c)#police 5000000 conform-action set-prec-transmit 3 ex R7(config-pmap-c)#$000 conform-action set-prec-transmit 3 exceed-action ? drop drop packet set-clp-transmit set atm clp and send it set-discard-class-transmit set discard-class and send it set-dscp-transmit set dscp and send it set-frde-transmit set FR DE and send it set-mpls-exp-imposition-transmit set exp at tag imposition and send it set-mpls-exp-topmost-transmit set exp on topmost label and send it set-prec-transmit rewrite packet precedence and send it set-qos-transmit set qos-group and send it transmit transmit packet R7(config-pmap-c)#$000 conform-action set-prec-transmit 3 exceed-action se R7(config-pmap-c)#$000 conform-action set-prec-transmit 3 exceed-action set-p R7(config-pmap-c)#$et-prec-transmit 3 exceed-action set-prec-transmit 1 R7(config-pmap-c-police)#exit R7(config-pmap-c)#exit R7(config-pmap)#class JPEG R7(config-pmap-c)#shap ? adaptive Enable Traffic Shaping adaptation to BECN average configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc only per interval fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fr-voice-adapt Enable rate adjustment depending on voice presence max-buffers Set Maximum Buffer Limit peak configure token bucket: CIR (bps) [Bc (bits) [Be (bits)]], send out Bc+Be per interval R7(config-pmap-c)#shap av R7(config-pmap-c)#shap average 10  ? <8000-154400000> Target Bit Rate (bits per second), the value needs to be multiple of 8000 percent % of interface bandwidth for Committed information rate R7(config-pmap-c)#shap average 1000000 R7(config-pmap-c)#int s   f 0/1 R7(config-if)#ser R7(config-if)#service-policy Prob    ? history Keep history of QoS metrics input Assign policy-map to the input of an interface output Assign policy-map to the output of an interface R7(config-if)#service-policy out Prob6 R7(config-if)#^Z R7#sh po *Mar 1 21:02:01.800: %SYS-5-CONFIG_I: Configured from console by console R7#sh pol R7#sh policy-map Policy Map Prob6 Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class S5Other police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 Class JPEG Traffic Shaping Average Rate Traffic Shaping CIR 1000000 (bps) Max. Buffers Limit 1000 (Packets) R7#sh ru | b poli % Ambiguous command: "sh ru " R7#sh ru | b poli sh ru | b polin | b poli policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 class JPEG shape average 1000000 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! --More--   R7#q  R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#policy Prob6 R7(config-pmap)#no class S5Other R7(config-pmap)#class S5Other R7(config-pmap-c)# police 5000000 conform-action set-prec-transmit 3 exceed$000000 conform-action set-prec-transmit 3 exceed- action seform-action set-prec-transmit 3 exceed-action set -prec-tran set-prec-transmit 3 exceed-action set-prec-tran smit 1 R7(config-pmap-c-police)# R7(config-pmap-c-police)#^Z R7#sh *Mar 1 21:05:03.017: %SYS-5-CONFIG_I: Configured from console by console R7#sh pol R7#sh policy-map Policy Map Prob6 Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class JPEG Traffic Shaping Average Rate Traffic Shaping CIR 1000000 (bps) Max. Buffers Limit 1000 (Packets) Class S5Other police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 R7#xo  config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#$form-action set-prec-transmit 3 exceed-action set-prec-transmit 1class S5Other no class S5Otherpolicy Prob6  R7(config-pmap)#policy Prob6$n set-prec-transmit 3 exceed-action set-prec-transmit 1class S5Other nclass S5Otheroclass S5Other class S5Other R7(config-pmap)#no class JPEG R7(config-pmap)#exit R7(config)#pol R7(config)#policy-map Prob6a R7(config-pmap)#class R7(config-pmap)#class    R7(config-pmap)#class class-default R7(config-pmap-c)# police cir 5000000 bc 156250 R7(config-pmap-c-police)# conform-action set-prec-transmit 3 R7(config-pmap-c-police)# exceed-action set-prec-transmit 1 R7(config-pmap-c-police)#exi R7(config-pmap-c)#exi R7(config-pmap)#exi R7(config)#pol R7(config)#policy-map Prob6b R7(config-pmap)#class JPEG R7(config-pmap-c)#shap aver 100000                exit R7(config-pmap)#exit R7(config)#no pol R7(config)#no policy-map Prob6b R7(config)#no policy-map Prob6bexit class JPEGpolicy-map Prob6b a R7(config-pmap)#class JPEG R7(config-pmap-c)#sha av 1000000 R7(config-pmap-c)#exit R7(config-pmap)#exit R7(config)#pol R7(config)#policy-map Prob6 R7(config-pmap)#class S5Other R7(config-pmap-c)#? QoS policy-map class configuration commands: bandwidth Bandwidth compression Activate Compression drop Drop all packets exit Exit from QoS class action configuration mode no Negate or set default values of a command police Police priority Strict Scheduling Priority for this Class queue-limit Queue Max Threshold for Tail Drop random-detect Enable Random Early Detection as drop policy service-policy Configure QoS Service Policy set Set QoS values shape Traffic Shaping R7(config-pmap-c)#ser R7(config-pmap-c)#service-policy ? WORD policy-map name R7(config-pmap-c)#service-policy Prob6a GTS : Can be enabled only at the first level R7(config-pmap-c)#do sh run | b pol policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other policy-map Prob6a class JPEG shape average 1000000 class class-default police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 --More--   R7(config-pmap-c)#o exit R7(config-pmap)#exit R7(config)#no policy-map Prob6a R7(config)#pol Prov b6 R7(config-pmap)#class JPEG R7(config-pmap-c)# shape average 1000000 R7(config-pmap-c)# class class-default R7(config-pmap-c)# police cir 5000000 bc 156250 R7(config-pmap-c-police)# conform-action set-prec-transmit 3 R7(config-pmap-c-police)# exceed-action set-prec-transmit 1 R7(config-pmap-c-police)#^Z R7# *Mar 1 21:16:26.713: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b pol policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other class JPEG shape average 1000000 class class-default police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address --More--   R7#sh run | b class class-map match-any JPEG match protocol http mime "*jpeg" match protocol http url "*.jpeg" match protocol http url "*.jpg" match protocol http url "*.jpe" class-map match-all S5Other match access-group 1 class-map match-all S5Telnet match access-group 1 match protocol telnet ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other class JPEG shape average 1000000 class class-default police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 ! --More--  ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex service-policy output Prob6 ! interface Serial1/0 no ip address encapsulation frame-relay --More--  ! interface Serial1/0.1 point-to-point ip address 180.40.7.65 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 703 frame-relay ip tcp header-compression frame-relay ip tcp compression-connections 20 ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address --More--   shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless --More--  ! no ip http server no ip http secure-server ! access-list 1 permit 208.28.1.2 ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! --More--   R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pol Prob6 R7(config-pmap)#pol Prob6 exceed-action set-prec-transmit 1conform-action set-prec-transmit 3police cir 5000000 bc 156250 class class-default n class class-defaulto class class-default class class-default R7(config-pmap)#class S5Other R7(config-pmap-c)#class S5Otherno class class-defaultpol Prob6  exceed-action set-prec-transmit 1conform-action set-prec-transmit 3police cir 5000000 bc 156250  R7(config-pmap-c-police)# police cir 5000000 bc 156250class S5Other no class class-defaultpol Prob6  exceed-action set-prec-transmit 1conform-action set-prec-transmit 3 R7(config-pmap-c-police)# conform-action set-prec-transmit 3police cir 5000000 bc 156250 class S5Other no class class-defaultpol Prob6  exceed-action set-prec-transmit 1 R7(config-pmap-c-police)#^Z R7# *Mar 1 21:19:46.016: %SYS-5-CONFIG_I: Configured from console by console R7#sh pol R7#sh policy-map int fa 0/1 FastEthernet0/1 Service-policy output: Prob6 Class-map: S5Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 1 Match: protocol telnet Queueing Output Queue: Conversation 265 Bandwidth 1000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: S5Other (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 1 police: cir 5000000 bps, bc 156250 bytes conformed 0 packets, 0 bytes; actions: set-prec-transmit 3 --More--   exceeded 0 packets, 0 bytes; actions: set-prec-transmit 1 conformed 0 bps, exceed 0 bps Class-map: JPEG (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol http mime "*jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpe" 0 packets, 0 bytes 5 minute rate 0 bps Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 1000000/1000000 6250 25000 25000 25 3125 --More-- RACK8AS>c7 [confirm] [OK] RACK8AS>r7 Trying R7 (1.1.1.1, 2007)... Open ************************************************************** Global Knowledge Hands-On Labs Access Server Access is restricted to Global Knowledge CCIE Students ************************************************************** Please re-enter your password. (This is the same password you used to log onto the Lab website.) If you see a username prompt, please wait 40 seconds and try again. If the username prompt persists, please reset equipment from your "Pod x" link. User Access Verification Password: Password OK   --More--   Adapt Queue Packets Bytes Packets Bytes Shaping --More--   R7#180.40.7.130 Trying 180.40.7.130 ... Open R4# RACK8AS>3 7 [Resuming connection 7 to r7 ... ] [Connection to r7 closed by foreign host] RACK8AS> [Resuming connection 8 to r7 ... ]  R4# R4# RACK8AS> [Resuming connection 8 to r7 ... ] R4#q [Connection to 180.40.7.130 closed by foreign host] R7# R7# RACK8AS>5 [Resuming connection 5 to r5 ... ] 20 S5#180.40.7.130 Trying 180.40.7.130 ... Open R4# RACK8AS>7 % 7 is not an open connection RACK8AS> [Resuming connection 5 to r5 ... ]  R4# RACK8AS>sh sess Conn Host Address Byte Idle Conn Name 1 r1 1.1.1.1 0 03:08 r1 2 r2 1.1.1.1 0 01:28 r2 3 r3 1.1.1.1 0 47 r3 4 r4 1.1.1.1 6 01:55 r4 * 5 r5 1.1.1.1 0 0 r5 6 r6 1.1.1.1 4 03:08 r6 8 r7 1.1.1.1 0 0 RACK8AS>8 [Resuming connection 8 to r7 ... ] R7#sh 180.40.7.130sh policy-map int fa 0/1 FastEthernet0/1 Service-policy output: Prob6 Class-map: S5Telnet (match-all) 15 packets, 849 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 1 Match: protocol telnet Queueing Output Queue: Conversation 265 Bandwidth 1000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: S5Other (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 1 police: cir 5000000 bps, bc 156250 bytes conformed 0 packets, 0 bytes; actions: set-prec-transmit 3 --More--   exceeded 0 packets, 0 bytes; actions: set-prec-transmit 1 conformed 0 bps, exceed 0 bps Class-map: JPEG (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol http mime "*jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpe" 0 packets, 0 bytes 5 minute rate 0 bps Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 1000000/1000000 6250 25000 25000 25 3125 --More--   R7# RACK8AS>5 [Resuming connection 5 to r5 ... ] R4#q [Connection to 180.40.7.130 closed by foreign host] S5# S5#ping 1180.40.7.130p180.40.7.130 180.40.7.130 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.130, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms S5# RACK8AS>8 [Resuming connection 8 to r7 ... ] R7#sh policy-map int fa 0/1 FastEthernet0/1 Service-policy output: Prob6 Class-map: S5Telnet (match-all) 21 packets, 1178 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 1 Match: protocol telnet Queueing Output Queue: Conversation 265 Bandwidth 1000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: S5Other (match-all) 5 packets, 570 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 1 police: cir 5000000 bps, bc 156250 bytes conformed 5 packets, 570 bytes; actions: set-prec-transmit 3 --More--   exceeded 0 packets, 0 bytes; actions: set-prec-transmit 1 conformed 0 bps, exceed 0 bps Class-map: JPEG (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol http mime "*jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpe" 0 packets, 0 bytes 5 minute rate 0 bps Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 1000000/1000000 6250 25000 25000 25 3125 --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#pri R7(config)#prio R7(config)#priority-list 1 ? default Set priority queue for unspecified datagrams interface Establish priorities for packets from a named interface protocol priority queueing by protocol queue-limit Set queue limits for priority queues R7(config)#priority-list 1 pro R7(config)#priority-list 1 protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dlsw Data Link Switching (Direct encapsulation only) ip IP ipv6 IPV6 ipx Novell IPX llc2 llc2 pad PAD links pppoe PPP over Ethernet --More--   qllc qllc protocol rsrb Remote Source-Route Bridging snapshot Snapshot routing support stun Serial Tunnel R7(config)#priority-list 1 protocol ip ? high medium normal low R7(config)#priority-list 1 protocol ip high ? fragments Prioritize fragmented IP packets gt Prioritize packets greater than a specified size list To specify an access list lt Prioritize packets less than a specified size tcp Prioritize TCP packets 'to' or 'from' the specified port udp Prioritize UDP packets 'to' or 'from' the specified port R7(config)#priority-list 1 protocol ip high tcp ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   R7(config)#priority-list 1 protocol ip high tcp tel R7(config)#priority-list 1 protocol ip high tcp telnet R7(config)#pi ri R7(config)#prio R7(config)#priority-list 1 prro  o R7(config)#priority-list 1 protocol ip loq we    ? fragments Prioritize fragmented IP packets gt Prioritize packets greater than a specified size list To specify an access list lt Prioritize packets less than a specified size tcp Prioritize TCP packets 'to' or 'from' the specified port udp Prioritize UDP packets 'to' or 'from' the specified port R7(config)#priority-list 1 protocol ip low tcp ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   pop2 Post Office Protocol v2 (109) pop3 Post Office Protocol v3 (110) smtp Simple Mail Transport Protocol (25) sunrpc Sun Remote Procedure Call (111) syslog Syslog (514) tacacs TAC Access Control System (49) talk Talk (517) telnet Telnet (23) time Time (37) uucp Unix-to-Unix Copy Program (540) whois Nicname (43) www World Wide Web (HTTP, 80) R7(config)#priority-list 1 protocol ip low tcp www R7(config)#int s 1/0.2 R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#pri R7(config-subif)#prio R7(config-subif)#prio R7(config-subif)#prio R7(config-subif)#prio R7(config-subif)#prio R7(config-subif)#prio R7(config-subif)#prio R7(config-subif)#prio R7(config-subif)#prio  ? % Unrecognized command R7(config-subif)#pr  int s 1/0 R7(config-if)#pri R7(config-if)#priority-group                int s 1/0.2 R7(config-subif)#fram  R7(config-subif)#fram pir  ri R7(config-subif)#fram priority-dlci-group ? <1-16> Assign priority group R7(config-subif)#fram priority-dlci-group 1 ? <16-1007> DLCI for high priority R7(config-subif)#fram priority-dlci-group 1 7-2    02 ? <16-1007> DLCI for medium priority R7(config-subif)#fram priority-dlci-group 1 702 702 ? <16-1007> DLCI for normal priority R7(config-subif)#fram priority-dlci-group 1 702 702 702 702 R7(config-subif)# *Mar 1 21:27:44.905: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-subif)#fram priority-dlci-group 1 702 702 702 702 \              sh    do shj r    h run int s 1/0.2 Building configuration... Current configuration : 208 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 end R7(config-subif)#no frame-relay priority-dlci-group 1 702 702 702 702 R7(config-subif)#no frame-relay priority-dlci-group 1 702 702 702 702do sh run int s 1/0.2 fram priority-dlci-group 1 702 702 702 702              R7(config-subif)#fram priority-dlci-group 1 702 no frame-relay priority-dlci-group 1 702 702 702 702do sh run int s 1/0.2  Building configuration... Current configuration : 208 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 end R7(config-subif)# *Mar 1 21:29:27.666: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7(config-subif)#sh    ^Z R7#sh *Mar 1 21:31:55.728: %SYS-5-CONFIG_I: Configured from console by console R7#sh   h run | b interface Serial1/0.2 interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 --More--   no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 1 permit 208.28.1.2 priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp www --More--  ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R7# R7# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#qu R3(config)#queue-list ? <1-16> Queue list number R3(config)#queue-list 1 ? default Set custom queue for unspecified datagrams interface Establish priorities for packets from a named interface lowest-custom Set lowest number of queue to be treated as custom protocol priority queueing by protocol queue Configure parameters for a particular queue stun Establish priorities for stun packets R3(config)#queue-list 1 pro R3(config)#queue-list 1 protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dlsw Data Link Switching (Direct encapsulation only) ip IP ipv6 IPV6 ipx Novell IPX llc2 llc2 pad PAD links pppoe PPP over Ethernet --More--   R3(config)#queue-list 1 protocol ip ? <0-16> queue number R3(config)#queue-list 1 protocol ip 1 ? fragments Prioritize fragmented IP packets gt Classify packets greater than a specified size list To specify an access list lt Classify packets less than a specified size tcp Prioritize TCP packets 'to' or 'from' the specified port udp Prioritize UDP packets 'to' or 'from' the specified port R3(config)#queue-list 1 protocol ip 1 tcp ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) --More--   R3(config)#queue-list 1 protocol ip 1 tcp tp    ftp R3(config)#queue-list 1 protocol ip 1 tcp ftp- R3(config)#queue-list 1 protocol ip 1 tcp ftp-data R3(config)#queue-list 1 protocol ip 1 tcp ftp-data          telp 1 tcp tel 2 tcp tel R3(config)#queue-list 1 protocol ip 2 tcp tel                     default 3 R3(config)#que R3(config)#queue-list 1 ? default Set custom queue for unspecified datagrams interface Establish priorities for packets from a named interface lowest-custom Set lowest number of queue to be treated as custom protocol priority queueing by protocol queue Configure parameters for a particular queue stun Establish priorities for stun packets R3(config)#queue-list 1 qu R3(config)#queue-list 1 queue ? <0-16> queue number R3(config)#queue-list 1 queue 1 ? byte-count Specify size in bytes of a particular queue limit Set queue entry limit of a particular queue R3(config)#queue-list 1 queue 1 by R3(config)#queue-list 1 queue 1 byte-count 2673 R3(config)#queue-list 1 queue 1 byte-count 2673    1295 byte-count 1295 2 byte-count 1295 R3(config)#queue-list 1 queue 2 byte-count 1295 4 byte-count 1294 3 byte-count 1294 R3(config)#int s 1/2 R3(config-if)#cu R3(config-if)#custom-queue-list 1 ? R3(config-if)#custom-queue-list 1 R3(config-if)#^Z R3# *Mar 1 21:43:14.850: %SYS-5-CONFIG_I: Configured from console by console R3#sh run s   | b interface Serial1/2 interface Serial1/2 ip address 180.40.7.1 255.255.255.224 custom-queue-list 1 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown --More--  ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 100 permit icmp host 100.1.1.1 host 20.10.1.2 echo access-list 101 permit icmp host 100.1.1.1 host 20.10.1.1 echo access-list 102 permit icmp host 100.1.1.1 20.10.1.0 0.0.0.255 echo queue-list 1 protocol ip 1 tcp ftp queue-list 1 protocol ip 1 tcp ftp-data queue-list 1 protocol ip 2 tcp telnet queue-list 1 default 3 queue-list 1 queue 1 byte-count 2673 queue-list 1 queue 2 byte-count 1295 queue-list 1 queue 3 byte-count 1294 ! route-map Prob1 permit 10 match ip address 102 --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#map R3(config)#map-c R3(config)#map-class fra test R3(config-map-class)#fra ? adaptive-shaping Adaptive traffic rate adjustment, Default = none bc Committed burst size (Bc), Default = 7000 bits be Excess burst size (Be), Default = 0 bits cir Committed Information Rate (CIR), Default = 56000 bps congestion Congestion management parameters custom-queue-list VC custom queueing end-to-end Configure frame-relay end-to-end VC parameters fair-queue VC fair queueing fecn-adapt Enable Traffic Shaping reflection of FECN as BECN fragment fragmentation - Requires Frame Relay traffic-shaping to be configured at the interface level holdq Hold queue size for VC idle-timer Idle timeout for a SVC, Default = 120 sec interface-queue PVC interface queue parameters ip Assign a priority queue for RTP streams mincir Minimum acceptable CIR, Default = CIR/2 bps priority-group VC priority queueing tc Policing Measurement Interval (Tc) traffic-rate VC traffic rate voice voice options R3(config-map-class)#fra     ? Static maps class configuration commands: default Set a command to its defaults exit-class Exit from static map class configuration mode frame-relay Configure Map parameters help Description of the interactive help system no Negate a command or set its defaults service-policy class-based service policy R3(config-map-class)#exit R3(config)#exitmap-class fra testnmap-class fra testomap-class fra test map-class fra test R3(config)# R3(config)# R3(config)# RACK8AS>7 % 7 is not an open connection RACK8AS> [Resuming connection 3 to r3 ... ] R3(config)# RACK8AS>8 [Resuming connection 8 to r7 ... ] R7#sh run | b class class-map match-any JPEG match protocol http mime "*jpeg" match protocol http url "*.jpeg" match protocol http url "*.jpg" match protocol http url "*.jpe" class-map match-all S5Other match access-group 1 class-map match-all S5Telnet match access-group 1 match protocol telnet ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 class JPEG shape average 1000000 ! ! --More--   R7# R7# R7# R7# R7# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3(config)#en % Ambiguous command: "en" R3(config)#end R3# *Mar 2 01:33:50.727: %SYS-5-CONFIG_I: Configured from console by console R3#rel R3#reload ? LINE Reason for reload at Reload at a specific time/date cancel Cancel pending reload in Reload after a time interval R3#reload at ? hh:mm Time to reload (hh:mm) R3#reload at           config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rel R3(config)#rel? % Unrecognized command R3(config)#rel   end R3# *Mar 2 01:34:35.700: %SYS-5-CONFIG_I: Configured from console by console R3#cre   test crash Buffered messages: eid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:52.882: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:52.882: TCP src=30258, dst=23, seq=609010638, ack=4035928424, win=4128 ACK PSH *Mar 1 20:02:53.195: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:53.195: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:53.199: TCP src=30258, dst=23, seq=609010640, ack=4035928424, win=4128 ACK PSH *Mar 1 20:02:53.267: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 20:02:53.375: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:53.375: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:53.375: TCP src=30258, dst=23, seq=609010642, ack=4035928424, win=4128 ACK PSH *Mar 1 20:02:53.531: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:53.535: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:53.535: TCP src=30258, dst=23, seq=609010644, ack=4035928424, win=4128 ACK PSH *Mar 1 20:02:53.892: IP: s=180.40.7.1 (local), d=224.0.0.5 (Serial1/2), len 80, sending broad/multicast, proto=89 *Mar 1 20:02:56.292: IP: s=180.40.7.65 (Serial1/0), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 20:02:56.820: IP: s=180.40.7.67 (Serial1/0), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 20:02:58.066: IP: s=180.40.7.66 (local), d=224.0.0.5 (Serial1/0), len 84, sending broad/multicast, proto=89 *Mar 1 20:02:59.597: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:02:59.597: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 42, sending *Mar 1 20:02:59.597: TCP src=30258, dst=23, seq=609010646, ack=4035928424, win=4128 ACK PSH *Mar 1 20:03:00.987: IP: tableid=0, s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), routed via FIB *Mar 1 20:03:00.991: IP: s=180.40.7.66 (local), d=180.40.7.65 (Serial1/0), len 40, sending *Mar 1 20:03:00.991: TCP src=30258, dst=23, seq=609010648, ack=4035928424, win=4128 ACK *Mar 1 20:06:43.720: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 20:08:07.858: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 20:08:09.357: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 20:08:10.358: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up *Mar 1 20:08:54.367: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 20:08:54.375: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 20:10:39.791: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 20:10:39.791: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 20:10:40.152: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 20:10:41.791: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 1 20:10:42.792: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down *Mar 1 20:11:22.541: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 20:11:23.683: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 20:11:24.685: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up *Mar 1 20:12:09.691: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 20:12:09.699: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done *Mar 1 21:43:14.850: %SYS-5-CONFIG_I: Configured from console by console *Mar 2 01:33:50.727: %SYS-5-CONFIG_I: Configured from console by console *Mar 2 01:34:35.700: %SYS-5-CONFIG_I: Configured from console by console Queued messages:WARNING: Command selections marked with '(crash router)' will crash router when issued. However a selection 'C' will need to be issued IMMEDIATELY before these selections to enable them. Type the number for the selected crash: -------------------------------------- 1 (crash router) Bus Error, due to invalid address access 2 (crash router) Bus Error, due to parity error in Main memory 3 (crash router) Bus Error, due to parity error in I/O memory 4 (crash router) Address Error, due to fetching code from odd address 5 (crash router) Jump to zero 6 (crash router) Software forced crash 7 (crash router) Illegal read of address zero 8 (crash router) Divide by zero 9 (crash router) Corrupt memory C Enable crash router selection marked with (crash router) R (crash router) User enter read bus error address U (crash router) User enter write bus error address W (crash router) Software watchdog timeout (*** Watch Dog Timeout ***) w (crash router) Process watchdog timeout (SYS-2-WATCHDOG) d Disable crashinfo collection e Enable crashinfo collection i Display contents of current crashinfo flash file m Write crashinfo on crashinfo RAM n Change crashinfo flash file name q Exit crash menu s Save crashinfo to current crashinfo flash file c Close current crashinfo flash file t Write crashinfo on console TTY x Exit crash menu ? x R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#int fa 0/0end  no map-class fra testexit map-class fra testexit no map-class fra testen dint fa 0/0 do sh run int fa 0/0 Building configuration... Current configuration : 126 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto end R3(config-if)#int s 1/2 R3(config-if)#int s 1/2do sh run int fa 0/0      s 1/2 Building configuration... Current configuration : 87 bytes ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 custom-queue-list 1 end R3(config-if)#no custom-queue-list 1 R3(config-if)#exit R3(config)#do sh run | i class ip classless R3(config)#cl  class-map FTP R3(config-cmap)#match pro R3(config-cmap)#match protocol ? aarp AppleTalk ARP appletalk AppleTalk arp IP ARP bgp Border Gateway Protocol bridge Bridging bstun Block Serial Tunnel cdp Cisco Discovery Protocol citrix Citrix Traffic clns ISO CLNS clns_es ISO CLNS End System clns_is ISO CLNS Intermediate System cmns ISO CMNS compressedtcp Compressed TCP cuseeme CU-SeeMe desktop video conference custom-01 Custom protocol custom-01 custom-02 Custom protocol custom-02 custom-03 Custom protocol custom-03 custom-04 Custom protocol custom-04 custom-05 Custom protocol custom-05 custom-06 Custom protocol custom-06 custom-07 Custom protocol custom-07 custom-08 Custom protocol custom-08 --More--   custom-09 Custom protocol custom-09 custom-10 Custom protocol custom-10 decnet DECnet decnet_node DECnet Node decnet_router-l1 DECnet Router L1 decnet_router-l2 DECnet Router L2 dhcp Dynamic Host Configuration dlsw Data Link Switching (Direct encapsulation only) dns Domain Name Server lookup egp Exterior Gateway Protocol eigrp Enhanced Interior Gateway Routing Protocol exchange MS-RPC for Exchange fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster... finger Finger ftp File Transfer Protocol gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella... gopher Gopher gre Generic Routing Encapsulation http World Wide Web traffic icmp Internet Control Message imap Internet Message Access Protocol ip IP ipinip IP in IP (encapsulation) --More--   R3(config-cmap)#match protocol ftp R3(config-cmap)#exit R3(config)#clea R3(config)#clea   R3(config)#cla R3(config)#class-map Telnet R3(config-cmap)#match p[ rot telnet R3(config-cmap)#exit R3(config)#pol R3(config)#policy-map Prob9 R3(config-pmap)#class R3(config-pmap)#class f FTP R3(config-pmap-c)#ban R3(config-pmap-c)#bandwidth ? <8-2000000> Kilo Bits per second percent % of total Bandwidth remaining % of the remaining bandwidth R3(config-pmap-c)#bandwidth per 50 R3(config-pmap-c)#exit R3(config-pmap)#class Telnet R3(config-pmap-c)#ban per 25 R3(config-pmap-c)#int s 1/2 R3(config-if)#ser R3(config-if)#serv R3(config-if)#service-policy out Prob9 R3(config-if)#do sh pol int s 1/2 Serial1/2 Service-policy output: Prob9 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 41 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 42 Bandwidth 25 (%) Bandwidth 32 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 2 packets, 108 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3(config-if)#do sh pol int s 1/2service-policy out Prob9nservice-policy out Prob9oservice-policy out Prob9 service-policy out Prob9 R3(config-if)#exit R3(config)#pol Prob9 R3(config-pmap)#clas class-default R3(config-pmap-c)#ban R3(config-pmap-c)#bandwidth per R3(config-pmap-c)#bandwidth percent 25 R3(config-pmap-c)#int  s 1/2 R3(config-if)#int s 1/2bandwidth percent 25clas class-default pol Prob9 exit no service-policy out Prob9do sh pol int s 1/2 service-policy out Prob9 I/f Serial1/2 class class-default requested bandwidth 25%, available only 0% R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#max R3(config-if)#max-reserved-bandwidth ? <1-100> Max. reservable bandwidth as % of interface bandwidth R3(config-if)#max-reserved-bandwidth 100 R3(config-if)#max-reserved-bandwidth 100service-policy out Prob9  R3(config-if)#service-policy out Prob9max-reserved-bandwidth 100service-policy out Prob9 int s 1/2 bandwidth percent 25clas class-default pol Prob9 exit no service-policy out Prob9 R3(config-if)#no service-policy out Prob9service-policy out Prob9  R3(config-if)#DO SH POL INT S 1/2 Serial1/2 Service-policy output: Prob9 Class-map: FTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol ftp Queueing Output Queue: Conversation 41 Bandwidth 50 (%) Bandwidth 64 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: Telnet (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol telnet Queueing Output Queue: Conversation 42 Bandwidth 25 (%) Bandwidth 32 (kbps) Max Threshold 64 (packets) --More--   (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: class-default (match-any) 2 packets, 108 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any Queueing Output Queue: Conversation 43 Bandwidth 25 (%) Bandwidth 32 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 R3(config)#do sh int s 1/2 Serial1/2 is up, line protocol is up Hardware is CD2430 in sync mode Internet address is 180.40.7.1/27 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input 00:00:06, output 00:00:06, output hang 06:46:59 Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: Class-based queueing Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 3/3 (allocated/max allocated) Available Bandwidth 0 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 5454 packets input, 430373 bytes, 0 no buffer Received 2850 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 12286 packets output, 599761 bytes, 0 underruns 0 output errors, 0 collisions, 6847 interface resets 0 output buffer failures, 0 output buffers swapped out --More--   R3(config)#end R3# *Mar 2 01:48:37.909: %SYS-5-CONFIG_I: Configured from console by console R3#sasodfasodfapsdfkoaskodf                        sh run | b class class-map match-all Telnet match protocol telnet class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class Telnet bandwidth percent 25 class class-default bandwidth percent 25 ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto --More--   speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20 frame-relay map ip 180.40.7.67 302 broadcast ! interface Serial1/1 no ip address shutdown --More--  ! interface Serial1/2 ip address 180.40.7.1 255.255.255.224 max-reserved-bandwidth 100 service-policy output Prob9 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#st R3(config-if)#standby n ? <0-255> group number authentication Authentication delay HSRP initialisation delay ip Enable HSRP and set the virtual IP address mac-address Virtual MAC address name Redundancy name string preempt Overthrow lower priority Active routers priority Priority level redirects Configure sending of ICMP Redirect messages with an HSRP virtual IP address as the gateway IP address timers Hello and hold timers track Priority tracking use-bia HSRP uses interface's burned in address R3(config-if)#standby 47 ip 180.40.7.132 R3(config-if)#stan R3(config-if)#standby pri R3(config-if)#standby priority ? <0-255> Priority value R3(config-if)#standby priority 150 *Mar 2 01:59:14.609: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active R3(config-if)#standby priority 150 priority 1504 priority 1507 priority 150 R3(config-if)#stand 47 pre R3(config-if)#stand 47 preempt R3(config-if)#stand 47 preempt nstand 47 preempt ostand 47 preempt  stand 47 preempt  R3(config-if)# RACK8AS>7 % 7 is not an open connection RACK8AS> [Resuming connection 3 to r3 ... ] R3(config-if)# RACK8AS>8 [Resuming connection 8 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#standby 47 ip 180.40.7.132 ^ % Invalid input detected at '^' marker. R7(config)#int fa 0/1 R7(config-if)#int fa 0/1standby 47 ip 180.40.7.132 R7(config-if)#st  standby 47 priority 200 R7(config-if)#do sh stand FastEthernet0/1 - Group 47 State is Speak Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.364 secs Preemption disabled Active router is 180.40.7.129, priority 150 (expires in 8.245 sec) Standby router is unknown Priority 200 (configured 200) IP redundancy name is "hsrp-Fa0/1-47" (default) R7(config-if)#do sh stand FastEthernet0/1 - Group 47 State is Standby 1 state change, last state change 00:00:02 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.648 secs Preemption disabled Active router is 180.40.7.129, priority 150 (expires in 7.532 sec) Standby router is local Priority 200 (configured 200) IP redundancy name is "hsrp-Fa0/1-47" (default) R7(config-if)#do sh standstandby 47 priority 200   101 R7(config-if)# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#tra R3(config-if)#tra   stan R3(config-if)#standby 47 tra R3(config-if)#standby 47 track ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing R3(config-if)#standby 47 track ser 1/2 R3(config-if)#do sh stand FastEthernet0/0 - Group 47 State is Active 2 state changes, last state change 00:03:47 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.893 secs Preemption disabled Active router is local Standby router is 180.40.7.131, priority 101 (expires in 8.005 sec) Priority 150 (configured 150) Track interface Serial1/2 state Up decrement 10 IP redundancy name is "hsrp-Fa0/0-47" (default) R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#do sh stand standby 47 track ser 1/2 50 R3(config-if)#int s `1/2    1/2 R3(config-if)#shut R3(config-if)# *Mar 2 02:03:37.255: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-if)# *Mar 2 02:03:39.250: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down *Mar 2 02:03:40.252: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down R3(config-if)#shutint s 1/2standby 47 track ser 1/2 50do sh stand  FastEthernet0/0 - Group 47 State is Active 2 state changes, last state change 00:04:30 Virtual IP address is 180.40.7.132 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.076 secs Preemption disabled Active router is local Standby router is 180.40.7.131, priority 101 (expires in 7.188 sec) Priority 100 (configured 150) Track interface Serial1/2 state Down decrement 50 IP redundancy name is "hsrp-Fa0/0-47" (default) R3(config-if)# RACK8AS>8 [Resuming connection 8 to r7 ... ] R7(config-if)#stan R7(config-if)#standby 47 pre R7(config-if)#standby 47 preempt R7(config-if)# *Mar 2 02:04:12.297: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 47 state Standby -> Active R7(config-if)# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-if)#no shut R3(config-if)#^Z R3# *Mar 2 02:05:01.261: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 2 02:05:02.811: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up *Mar 2 02:05:03.813: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up R3# *Mar 2 02:05:12.884: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from LOADING to FULL, Loading Done R3#sh    config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/    dfa   fa 0/0 R3(config-if)#stand 47 pree R3(config-if)# *Mar 2 02:05:35.753: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active R3(config-if)#^Z R3# *Mar 2 02:05:40.942: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int fa 0/0 Building configuration... Current configuration : 230 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/2 50 end R3# RACK8AS>8 [Resuming connection 8 to r7 ... ] *Mar R7(config-if)#^Z R7#sh run int fa *Mar 2 02:06:00.903: %SYS-5-CONFIG_I: Configured from console by console R7#sh run int fa 0/1 Building configuration... Current configuration : 201 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex standby 47 ip 180.40.7.132 standby 47 priority 101 standby 47 preempt service-policy output Prob6 end R7# R7# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#stan R3(config-if)#standby 47 track s 1/2 0 R3(config-if)#standby 47 track s 1/0 standby 47 track s 1/0 50 R3(config-if)#end R3#sh *Mar 2 02:10:26.458: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int s  fa 0/      fa - 0/0 Building configuration... Current configuration : 261 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/2 50 standby 47 track Serial1/0 50 end R3# R3#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/32 is subnetted, 1 subnets O 100.1.1.1 [110/2] via 180.40.7.130, 00:06:13, FastEthernet0/0 20.0.0.0/24 is subnetted, 2 subnets O 20.10.2.0 [110/792] via 180.40.7.67, 00:06:13, Serial1/0 [110/792] via 180.40.7.2, 00:06:13, Serial1/2 O 20.10.1.0 [110/782] via 180.40.7.67, 00:06:13, Serial1/0 [110/782] via 180.40.7.2, 00:06:13, Serial1/2 O 208.28.1.0/24 [110/2] via 180.40.7.131, 00:06:13, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.162/32 [110/781] via 180.40.7.67, 00:06:14, Serial1/0 [110/781] via 180.40.7.2, 00:06:14, Serial1/2 O 180.40.7.161/32 [110/1] via 180.40.7.131, 00:06:14, FastEthernet0/0 --More--   R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#tr R3(config)#tr R3(config)#trA R3(config)#trA ac R3(config)#track ? <1-500> Tracked object resolution Tracking resolution parameters timer Polling interval timers R3(config)#track 1 ? interface Select an interface to track ip IP protocol R3(config)#track 1 ip ? route IP route R3(config)#track 1 ip route ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R3(config)#track 1 ip route 20.10.2.0/24 ? metric Route metric reachability Route reachability state R3(config)#track 1 ip route 20.10.2.0/24 re R3(config)#track 1 ip route 20.10.2.0/24 reachability ? R3(config)#track 1 ip route 20.10.2.0/24 reachability % Cannot change object created via HSRP R3(config)#track 1 ip route 20.10.2.0/24 reachability  ip route 20.10.2.0/24 reachability 3 ip route 20.10.2.0/24 reachability  R3(config-track)#exit R3(config)#int fa 0/0 R3(config-if)#sta R3(config-if)#standby 47 ? authentication Authentication ip Enable HSRP and set the virtual IP address mac-address Virtual MAC address name Redundancy name string preempt Overthrow lower priority Active routers priority Priority level timers Hello and hold timers track Priority tracking R3(config-if)#standby 47 tr R3(config-if)#standby 47 track ? <1-500> Tracked object number Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-TokenRing Virtual TokenRing R3(config-if)#standby 47 track 3 ? decrement Priority decrement R3(config-if)#standby 47 track 3 de R3(config-if)#standby 47 track 3 decrement 50 R3(config-if)#end R3#sh r *Mar 2 02:19:40.534: %SYS-5-CONFIG_I: Configured from console by console R3#sh ru |    n | b track track 3 ip route 20.10.2.0 255.255.255.0 reachability ! ! ! class-map match-all Telnet match protocol telnet class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class Telnet bandwidth percent 25 class class-default bandwidth percent 25 ! ! ! ! ! ! --More--  interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/2 50 standby 47 track Serial1/0 50 standby 47 track 3 decrement 50 ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 --More--   R3#sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 131 0012.43ac.6e61 ARPA FastEthernet0/0 Internet 180.40.7.130 131 000e.38f1.08e0 ARPA FastEthernet0/0 Internet 180.40.7.129 - 0012.8014.1900 ARPA FastEthernet0/0 Internet 180.40.7.132 - 0000.0c07.ac2f ARPA FastEthernet0/0 R3# R3# R3# R3# R3# R3# R3# R3#sh run int fa 0/0 Building configuration... Current configuration : 294 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto standby 47 ip 180.40.7.132 standby 47 priority 150 standby 47 preempt standby 47 track Serial1/2 50 standby 47 track Serial1/0 50 standby 47 track 3 decrement 50 end R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no standby 47 ip 180.40.7.132 ^ % Invalid input detected at '^' marker. R3(config)#int fa 0/90 ^ % Invalid input detected at '^' marker. R3(config)#int fa 0/90  0 R3(config-if)#int fa 0/090no standby 47 ip 180.40.7.132 R3(config-if)#no *Mar 2 02:25:05.427: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Active -> Disabled R3(config-if)#no    no stand 47 R3(config-if)#sh run int dsh run int osh run int  sh run int sh run int fa 0/0 Building configuration... Current configuration : 126 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto end R3(config-if)# RACK8AS>8 [Resuming connection 8 to r7 ... ] *Ma R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#no stand 47 R7(config-if)# *Mar 2 02:25:32.219: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 47 state Active -> Disabled R7(config-if)#vrr R7(config-if)#vrrp ? <1-255> Group number R7(config-if)#vrrp 1 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R7(config-if)#vrrp 1 ip ? A.B.C.D VRRP group IP address R7(config-if)#vrrp 1 ip 180.5 40.7.`32   132 1 2 R7(config-if)# *Mar 2 02:27:43.554: %VRRP-6-STATECHANGE: Fa0/1 Grp 1 state Init -> Backup R7(config-if)# *Mar 2 02:27:47.164: %VRRP-6-STATECHANGE: Fa0/1 Grp 1 state Backup -> Master R7(config-if)#vrrp 1 ? authentication Authentication string description Group specific description ip Enable Virtual Router Redundancy Protocol (VRRP) for IP preempt Enable preemption of lower priority Master priority Priority of this VRRP group timers Set the VRRP timers R7(config-if)#vrrp 1 pri R7(config-if)#vrrp 1 priority 101 R7(config-if)# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#vrrp 1 ip 180.40.7.132 R3(config-if)# *Mar 2 02:28:39.353: %VRRP-6-STATECHANGE: Fa0/0 Grp 1 state Init -> Backup R3(config-if)#vrrp 1 pri R3(config-if)#vrrp 1 priority 10 50 R3(config-if)#vrrp 1 pre R3(config-if)#vrrp 1 preempt R3(config-if)# *Mar 2 02:28:49.286: %VRRP-6-STATECHANGE: Fa0/0 Grp 1 state Backup -> Master R3(config-if)#^Z R3# *Mar 2 02:28:54.434: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int fa 0/0-  Building configuration... Current configuration : 171 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto vrrp 1 ip 180.40.7.132 vrrp 1 priority 150 end R3# RACK8AS> [Resuming connection 3 to r3 ... ] R3#sh r vrrp FastEthernet0/0 - Group 1 State is Master Virtual IP address is 180.40.7.132 Virtual MAC address is 0000.5e00.0101 Advertisement interval is 1.000 sec Preemption enabled Priority is 150 Master Router is 180.40.7.129 (local), priority is 150 Master Advertisement interval is 1.000 sec Master Down interval is 3.414 sec R3# RACK8AS>7 % 7 is not an open connection RACK8AS> [Resuming connection 3 to r3 ... ] RACK8AS>8 [Resuming connection 8 to r7 ... ] * R7(config-if)#^Z R7#sh vr *Mar 2 02:29:25.297: %SYS-5-CONFIG_I: Configured from console by console R7#sh vrrp FastEthernet0/1 - Group 1 State is Backup Virtual IP address is 180.40.7.132 Virtual MAC address is 0000.5e00.0101 Advertisement interval is 1.000 sec Preemption enabled Priority is 101 Master Router is 180.40.7.129, priority is 150 Master Advertisement interval is 1.000 sec Master Down interval is 3.605 sec (expires in 3.136 sec) R7#sh run int fa 0/1 Building configuration... Current configuration : 173 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 1 ip 180.40.7.132 vrrp 1 priority 101 service-policy output Prob6 end R7# R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#stand 47 ip 180 5   0.40.7.133 R7(config-if)#do sh rubn    n int fa 0/1 Building configuration... Current configuration : 201 bytes ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex vrrp 1 ip 180.40.7.132 vrrp 1 priority 101 standby 47 ip 180.40.7.133 service-policy output Prob6 end R7(config-if)#ah    do sh vrrp FastEthernet0/1 - Group 1 State is Backup Virtual IP address is 180.40.7.132 Virtual MAC address is 0000.5e00.0101 Advertisement interval is 1.000 sec Preemption enabled Priority is 101 Master Router is 180.40.7.129, priority is 150 Master Advertisement interval is 1.000 sec Master Down interval is 3.605 sec (expires in 3.140 sec) R7(config-if)#do sh stand FastEthernet0/1 - Group 47 State is Speak Virtual IP address is 180.40.7.133 Active virtual MAC address is unknown Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 1.987 secs Preemption disabled Active router is unknown Standby router is unknown Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/1-47" (default) R7(config-if)# *Mar 2 02:31:16.427: %HSRP-6-STATECHANGE: FastEthernet0/1 Grp 47 state Standby -> Active R7(config-if)#do sh standvrrp  FastEthernet0/1 - Group 1 State is Backup Virtual IP address is 180.40.7.132 Virtual MAC address is 0000.5e00.0101 Advertisement interval is 1.000 sec Preemption enabled Priority is 101 Master Router is 180.40.7.129, priority is 150 Master Advertisement interval is 1.000 sec Master Down interval is 3.605 sec (expires in 2.868 sec) R7(config-if)#do sh vrrpstand FastEthernet0/1 - Group 47 State is Active 2 state changes, last state change 00:00:12 Virtual IP address is 180.40.7.133 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 2.672 secs Preemption disabled Active router is local Standby router is unknown Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/1-47" (default) R7(config-if)#vrrp ? <1-255> Group number R7(config-if)#vrrp      stan R7(config-if)#standby 47 pri 150 R7(config-if)#stand 47 pre R7(config-if)# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s f 0/0 R3(config-if)#stand 47 ip 180.40.7.133 R3(config-if)#stan 47 prin            ^Z R3# *Mar 2 02:33:30.719: %SYS-5-CONFIG_I: Configured from console by console R3#sh stand FastEthernet0/0 - Group 47 State is Listen Virtual IP address is 180.40.7.133 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Preemption disabled Active router is 180.40.7.131, priority 150 (expires in 8.165 sec) Standby router is unknown Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/0-47" (default) R3#sh bsr   B   B    sh stand FastEthernet0/0 - Group 47 State is Standby 1 state change, last state change 00:00:20 Virtual IP address is 180.40.7.133 Active virtual MAC address is 0000.0c07.ac2f Local virtual MAC address is 0000.0c07.ac2f (default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.220 secs Preemption disabled Active router is 180.40.7.131, priority 150 (expires in 7.741 sec) Standby router is local Priority 100 (default 100) IP redundancy name is "hsrp-Fa0/0-47" (default) R3#sh vrrp FastEthernet0/0 - Group 1 State is Master Virtual IP address is 180.40.7.132 Virtual MAC address is 0000.5e00.0101 Advertisement interval is 1.000 sec Preemption enabled Priority is 150 Master Router is 180.40.7.129 (local), priority is 150 Master Advertisement interval is 1.000 sec Master Down interval is 3.414 sec R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip dh R3(config)#ip dhcp ? aaa Configure aaa attributes binding DHCP address bindings bootp BOOTP specific configuration conflict DHCP address conflict parameters database Configure DHCP database agents excluded-address Prevent DHCP from assigning certain addresses limited-broadcast-address Use all 1's broadcast address ping Specify ping parameters used by DHCP pool Configure DHCP address pools relay DHCP relay agent parameters smart-relay Enable Smart Relay feature R3(config)#ip dhcp ex R3(config)#ip dhcp excluded-address ? A.B.C.D Low IP address R3(config)#ip dhcp excluded-address 180.40.7.129 ? A.B.C.D High IP address R3(config)#ip dhcp excluded-address 180.40.7.129 R3(config)#ip dhcp excluded-address 180.40.7.129    31 180.40.7.132 R3(config)#do sh run | i ip dhcp ip dhcp excluded-address 180.40.7.129 ip dhcp excluded-address 180.40.7.131 180.40.7.132 R3(config)#ip dhs cp poo R3(config)#ip dhcp pool ? WORD Pool name R3(config)#ip dhcp pool Prob13 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#netwo R3(dhcp-config)#network > \ ? A.B.C.D Network number in dotted-decimal notation R3(dhcp-config)#network 180.40.7.128 ? /nn or A.B.C.D Network mask or prefix length R3(dhcp-config)#network 180.40.7.128 /27 ? R3(dhcp-config)#network 180.40.7.128 /27 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#def R3(dhcp-config)#default-router 180.40.7.132 R3(dhcp-config)#d R3(dhcp-config)#do R3(dhcp-config)#domain-name            ns R3(dhcp-config)#dns-server ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#dns-server 208.28.1.82 ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#dns-server 208.28.1.82 R3(dhcp-config)#dom R3(dhcp-config)#domain-name ? WORD Domain name R3(dhcp-config)#domain-name ccie.com R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   utilization Configure various utilization parameters vrf Associate this pool with a VRF R3(dhcp-config)#op R3(dhcp-config)#option ? <0-254> DHCP option code R3(dhcp-config)#option 150 ? ascii Data is an NVT ASCII string hex Data is a hexadecimal string instance Specify the option instance ip Data is one or more IP addresses R3(dhcp-config)#option 150 ip ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#option 150 ip 20.20.290  0.20 ? Hostname or A.B.C.D Server's name or IP address R3(dhcp-config)#option 150 ip 20.20.20.20 R3(dhcp-config)#exit R3(config)#do sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 154 0012.43ac.6e61 ARPA FastEthernet0/0 Internet 180.40.7.130 154 000e.38f1.08e0 ARPA FastEthernet0/0 Internet 180.40.7.129 - 0012.8014.1900 ARPA FastEthernet0/0 Internet 180.40.7.132 - 0000.5e00.0101 ARPA FastEthernet0/0 R3(config)# R3#con *Mar 2 02:45:33.095: %SYS-5-CONFIG_I: Configured from console by console R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip dhcp pool Prob13 R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#host ? A.B.C.D IP address in dotted-decimal notation R3(dhcp-config)#host      har R3(dhcp-config)#hardware-address ? WORD Dotted-hexadecimal string (aabb.ccdd.eeff ...) R3(dhcp-config)#hardware-address 000e.38f1.08e0 ? <0-255> ARP hardware type from "Assigned Numbers" RFC ethernet 10Mb Ethernet ieee802 IEEE 802 networks R3(dhcp-config)#hardware-address 000e.38f1.08e0 % This command may not be used with network, origin or vrf pools. R3(dhcp-config)#exit R3(config)#ip dcp~   hcp pool ForR4 R3(dhcp-config)#har R3(dhcp-config)#hardware-address 000e.38f1.08e0 R3(dhcp-config)#host ? A.B.C.D IP address in dotted-decimal notation R3(dhcp-config)#host 180.40.7.130 ? /nn or A.B.C.D Network mask or prefix length R3(dhcp-config)#host 180.40.7.130 /27 ? R3(dhcp-config)#host 180.40.7.130 /27 R3(dhcp-config)#^Z R3#sh ip h *Mar 2 02:47:17.234: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip h dhcp bin R3#sh ip dhcp binding Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 000e.38f1.08e0 Infinite Manual R3# R3# R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip dhcp ? aaa Configure aaa attributes binding DHCP address bindings bootp BOOTP specific configuration conflict DHCP address conflict parameters database Configure DHCP database agents excluded-address Prevent DHCP from assigning certain addresses limited-broadcast-address Use all 1's broadcast address ping Specify ping parameters used by DHCP pool Configure DHCP address pools relay DHCP relay agent parameters smart-relay Enable Smart Relay feature R3(config)#ip dhcp         ^Z R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip    ip dhcp data ? WORD Uniform Resource Locator (URL) R4(config)#ip dhcp data ert ? timeout Set the database transfer timeout write-delay Set the database write delay R4(config)#ip dhcp data ert                  int fa 0/0 R4(config-if)#ip dhcp ? relay DHCP relay configuration parameters R4(config-if)#ip dhcp      add dhcp ? client-id Specify client-id to use hostname Specify value for hostname option R4(config-if)#ip add dhcp R4(config-if)# *Mar 2 02:53:12.377: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 2 02:53:12.381: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#^Z R4# *Mar 2 02:53:17.405: IP: s=0.0.0.0 (local), d=255.255.255.255, len 604, policy rejected -- normal forwarding R4# *Mar 2 02:53:18.033: %SYS-5-CONFIG_I: Configured from console by console R4# *Mar 2 02:53:20.405: IP: s=0.0.0.0 (local), d=255.255.255.255, len 604, policy rejected -- normal forwarding *Mar 2 02:53:20.917: IP: s=0.0.0.0 (local), d=255.255.255.255, len 604, policy rejected -- normal forwarding R4# *Mar 2 02:53:24.961: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.134, mask 255.255.255.224, hostname R4 R4#sh acp  rp Protocol Address Age (min) Hardware Addr Type Interface Internet 180.40.7.131 0 0012.43ac.6e61 ARPA FastEthernet0/0 Internet 180.40.7.134 - 000e.38f1.08e0 ARPA FastEthernet0/0 R4# *Mar 2 02:54:03.933: IP: s=180.40.7.134 (local), d=180.40.7.129 (FastEthernet0/0), len 64, policy rejected -- normal forwarding *Mar 2 02:54:03.937: IP: s=180.40.7.134 (local), d=180.40.7.131 (FastEthernet0/0), len 64, policy rejected -- normal forwarding *Mar 2 02:54:03.941: IP: s=180.40.7.134 (local), d=180.40.7.131 (FastEthernet0/0), len 284, policy rejected -- normal forwarding *Mar 2 02:54:03.949: IP: s=180.40.7.134 (local), d=180.40.7.131 (FastEthernet0/0), len 64, policy rejected -- normal forwarding *Mar 2 02:54:03.949: IP: s=180.40.7.134 (local), d=180.40.7.131 (FastEthernet0/0), len 56, policy rejected -- normal forwarding *Mar 2 02:54:03.953: IP: s=180.40.7.134 (local), d=180.40.7.131 (FastEthernet0/0), len 96, policy rejected -- normal forwarding *Mar 2 02:54:03.957: IP: s=180.40.7.134 (local), d=180.40.7.131 (FastEthernet0/0), len 64, policy rejected -- normal forwarding R4# *Mar 2 02:54:03.961: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#u all All possible debugging has been turned off R4# *Mar 2 02:54:08.949: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh ip dhcp bin R3#sh ip dhcp binding ? A.B.C.D IP address in dotted-decimal notation | Output modifiers R3#sh ip dhcp binding Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 000e.38f1.08e0 Infinite Manual 180.40.7.134 0063.6973.636f.2d30. Mar 03 1993 02:50 AM Automatic 3030.652e.3338.6631. 2e30.3865.302d.4661. 302f.30 R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#host 180.40.7.130 /27 ardware-address 000e.38f1.08e0ip dhcp pool ForR4  R3(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R3(dhcp-config)#cli R3(dhcp-config)#client-n R3(dhcp-config)#client-name ? WORD Client name (domain should not be included) R3(dhcp-config)#client-name R4 R3(dhcp-config)#^Z R3# *Mar 2 02:53:19.340: %SYS-5-CONFIG_I: Configured from console by console R3#clea ip dhcp binm  % Incomplete command. R3#clea ip dhcp bin * R3# RACK8AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#shut R4(config-if)# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID CR2 Fas 0/8 128 R 2520 Eth 0 CCIE-S1-HUB Fas 0/23 163 T S WS-C2924-XFas 0/8 R3 Fas 0/3 168 R S 2611XM Fas 0/0 R7 Fas 0/7 166 R S 2611XM Fas 0/0 S6 Fas 0/24 130 R S I WS-C3550-2Fas 0/24 S5# RACK8AS>6 [Resuming connection 6 to r6 ... ] 18 S6#sh cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID Local Intrfce Holdtme Capability Platform Port ID R2 Fas 0/2 156 R S 2611XM Fas 0/1 R1 Fas 0/1 146 R 2611 Eth 0/1 R7 Fas 0/7 156 R S 2611XM Fas 0/1 S5 Fas 0/24 170 R S I WS-C3550-2Fas 0/24 S6#c  RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int     do sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/4, Fa0/5 Fa0/6, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Gi0/1, Gi0/2 10 VLAN0010 active Fa0/3 16 VLAN0016 active 20 VLAN0020 active 30 VLAN0030 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 16 enet 100016 1500 - - - - - 0 0 --More--   S5(config)# RACK8AS>6 [Resuming connection 6 to r6 ... ] S6#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/3, Fa0/5, Fa0/6, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Gi0/1 Gi0/2 10 VLAN0010 active Fa0/4, Fa0/7 16 VLAN0016 active 20 VLAN0020 active 30 VLAN0030 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 16 enet 100016 1500 - - - - - 0 0 --More--   S6#do  config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/4 S6(config-if)#sp S6(config-if)#span S6(config-if)#spanning-tree po S6(config-if)#spanning-tree portr f S6(config-if)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/4 but will only have effect when the interface is in a non-trunking mode. S6(config-if)#^Z S6#^x4 % Unknown command or computer name, or unable to find computer address S6# S6# 1d02h: %SYS-5-CONFIG_I: Configured from console by console S6# RACK8AS>4 [Resuming connection 4 to r4 ... ] * R4(config-if)#no shut R4(config-if)# *Mar 2 02:57:10.029: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 2 02:57:11.029: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R4(config-if)# *Mar 2 02:57:19.133: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.135, mask 255.255.255.224, hostname R4 R4(config-if)# RACK8AS> [Resuming connection 4 to r4 ... ] R4(config-if)#no   *Mar 2 02:57:28.085: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)#shut RACK8AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#clea ip dhcp bin *  % Incomplete command. R3#clea ip dhcp bin * R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#client-name R4ip dhcp pool ForR4host 180.40.7.130 /27 ip dhcp pool ForR4 client-name R4 ip dhcp pool ForR4 R3(dhcp-config)#c R3(dhcp-config)#client-? client-identifier client-name R3(dhcp-config)#client-i R3(dhcp-config)#client-identifier 0063.6973.636f.2d30.3030.652e.3338.6631.2e3$tifier 0063.6973.636f.2d30.3030.652e.3338.6631.2e30 .3865.3023.6973.636f.2d30.3030.652e.3338.6631.2e30.3865.302d .4661.302f.2d30.3030.652e.3338.6631.2e30.3865.302d.4661.302f .30 R3(dhcp-config)#^Z R3#sh ip *Mar 2 02:55:37.831: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip dc hcp bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.130 0063.6973.636f.2d30. Infinite Manual 3030.652e.3338.6631. 2e30.3865.302d.4661. 302f.30 R3#\sh ip dhcp bin\   RACK8AS>4 [Resuming connection 4 to r4 ... ] R4(con R4(config-if)#no shut R4(config-if)# *Mar 2 02:58:15.513: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 2 02:58:16.513: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R4(config-if)# *Mar 2 02:58:22.577: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 180.40.7.130, mask 255.255.255.224, hostname R4 R4(config-if)# *Mar 2 02:58:31.565: %OSPF-5-ADJCHG: Process 1, Nbr 208.28.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)# *Mar 2 02:58:32.881: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-if)#^Z R4# *Mar 2 02:59:42.865: %SYS-5-CONFIG_I: Configured from console by console R4# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run | ip dhcp ^ % Invalid input detected at '^' marker. R3#sh run | ip dhcpbip dhcp ip dhcp ip dhcp excluded-address 180.40.7.129 ip dhcp excluded-address 180.40.7.131 180.40.7.132 ! ip dhcp pool Prob13 network 180.40.7.128 255.255.255.224 default-router 180.40.7.132 dns-server 208.28.1.82 domain-name ccie.com option 150 ip 20.20.20.20 ! ip dhcp pool ForR4 host 180.40.7.130 255.255.255.224 client-identifier 0063.6973.636f.2d30.3030.652e.3338.6631.2e30.3865.302d.4661.302f.30 client-name R4 ! ip cef no ip domain lookup ip audit po max-events 100 ! ! ! ! --More--   R3# RACK8AS>2 [Resuming connection 2 to r2 ... ] *M R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa 0/1 R2(config-if)#ip hel R2(config-if)#ip help R2(config-if)#ip helper-address 208.28.1.99 R2(config-if)#^Z R2# *Mar 2 03:12:58.705: %SYS-5-CONFIG_I: Configured from console by console R2# RACK8AS>8 [Resuming connection 8 to r7 ... ] *Mar R7(config-if)#int s  1/0.2 R7(config-subif)#ip   p healp\    lper 1 208.28.1.99 R7(config-subif)#do sh run int s 1/0.2 Building configuration... Current configuration : 239 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 end R7(config-subif)# frame-relay interface-dlci 702 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R7(config-subif)# frame-relay interface-dlci 702 pro R7(config-subif)# frame-relay interface-dlci 702 protocol ? A.B.C.D Protocol specific address ip IP R7(config-subif)# frame-relay interface-dlci 702 protocol ip ? A.B.C.D Protocol specific address R7(config-subif)# frame-relay interface-dlci 702 protocol ip 180.40.7.162 %Can't add another VC to point-to-point subinterface R7(config-fr-dlci)# frame-relay interface-dlci 702 protocol ip 180.40.7.162do sh run int s 1/0.2  frame-relay interface-dlci 702 protocol ip 180.40.7.162 no frame-relay interface-dlci 702 R7(config-subif)#no frame-relay interface-dlci 702 *Mar 2 03:17:34.533: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from FULL to DOWN, Neighbor Down: Interface down or detached R7(config-subif)#no frame-relay interface-dlci 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 R7(config-fr-dlci)# *Mar 2 03:17:58.877: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/0.2 from LOADING to FULL, Loading Done R7(config-fr-dlci)#^Z R7# RACK8AS>2 [Resuming connection 2 to r2 ... ] * R2#sh run int fa 0/0 Building configuration... Current configuration : 83 bytes ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto end R2#sh run int fa 0/0 1 Building configuration... Current configuration : 125 bytes ! interface FastEthernet0/1 ip address 20.10.1.1 255.255.255.0 ip helper-address 208.28.1.99 duplex auto speed auto end R2# RACK8AS>8 [Resuming connection 8 to r7 ... ] *M R7#sh run int s 1/0.2 Building configuration... Current configuration : 261 bytes ! interface Serial1/0.2 point-to-point ip address 180.40.7.161 255.255.255.224 ip helper-address 208.28.1.99 ip ospf network point-to-multipoint frame-relay priority-dlci-group 1 702 702 702 702 frame-relay interface-dlci 702 protocol ip 180.40.7.162 end R7#sh fram map Serial1/0.1 (up): point-to-point dlci, dlci 703(0x2BF,0xACF0), broadcast status defined, active, TCP/IP Header Compression (inherited), connections: 20 Serial1/0.2 (up): point-to-point dlci, dlci 702(0x2BE,0xACE0), broadcast status defined, active Priority DLCI Group 1, DLCI 702 (HIGH), DLCI 702 (MEDIUM) DLCI 702 (NORMAL), DLCI 702 (LOW) R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#no vrrp 1 R7(config-if)#b *Mar 2 03:25:13.145: %VRRP-6-STATECHANGE: Fa0/1 Grp 1 state Backup -> Disable R7(config-if)#b no stan 47 R7(config-if)# RACK8AS>3 [Resuming connection 3 to r3 ... ] *93: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Standby -> Active R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#no vrrp 1 R3(config-if)#no *Mar 2 03:25:26.182: %VRRP-6-STATECHANGE: Fa0/0 Grp 1 state Master -> Disable R3(config-if)#no stand 47 R3(config-if)# *Mar 2 03:25:30.221: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Active -> Disabled R3(config-if)#gl R3(config-if)#glbp ? <0-1023> Group number R3(config-if)#glbp 0 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R3(config-if)#glbp 0 ip ? A.B.C.D Virtual IP address R3(config-if)#glbp 0 ip 180.40.7.132 ? secondary Make this IP address a secondary address R3(config-if)#glbp 0 ip 180.40.7.132 R3(config-if)#gl R3(config-if)#glbp 0 ? authentication Authentication method forwarder Forwarder configuration ip Enable group and set virtual IP address load-balancing Load balancing method preempt Overthrow lower priority designated routers priority Priority level timers Adjust GLBP timers weighting Gateway weighting and tracking R3(config-if)#glbp 0 pr R3(config-if)#glbp 0 pr  pri R3(config-if)#glbp 0 priority ? <1-255> Priority value R3(config-if)#glbp 0 priority *Mar 2 03:26:22.743: %GLBP-6-STATECHANGE: FastEthernet0/0 Grp 0 state Standby -> Active R3(config-if)#glbp 0 priority *Mar 2 03:26:32.743: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 0 Fwd 1 state Listen -> Active R3(config-if)#glbp 0 priority          wei R3(config-if)#glbp 0 weighting ? <1-254> Weighting maximum value track Interface tracking R3(config-if)#glbp 0 weighting                  exit R3(config)#tra R3(config)#trac R3(config)#track k 4 ? interface Select an interface to track ip IP protocol R3(config)#track 4 ip ? route IP route R3(config)#track 4 ip route ? A.B.C.D {/nn || A.B.C.D} Prefix and mask R3(config)#track 4 ip route 20.10.1.1  ~/24     1/24 re R3(config)#track 4 ip route 20.10.1.1/24 reachability R3(config-track)#exit R3(config)#int fa 0/0 R3(config-if)#gp R3(config-if)#gp l R3(config-if)#glbp 0 we R3(config-if)#glbp 0 weighting tr R3(config-if)#glbp 0 weighting track ? <1-500> Tracked object R3(config-if)#glbp 0 weighting track 4 ? decrement Weighting decrement R3(config-if)#glbp 0 weighting track 4 dec R3(config-if)#glbp 0 weighting track 4 decrement ? <1-255> Decrement value R3(config-if)#glbp 0 weighting track 4 decrement                   100 ? lower Weighting lower threshold upper Weighting upper threshold R3(config-if)#glbp 0 weighting 100 lo R3(config-if)#glbp 0 weighting 100 lower 75 100     ? upper Weighting upper threshold R3(config-if)#glbp 0 weighting 100 lower 75 up R3(config-if)#glbp 0 weighting 100 lower 75 upper 100 ? R3(config-if)#glbp 0 weighting 100 lower 75 upper 100 R3(config-if)#glbp 0 weighting 100 lower 75 upper 100                        tr R3(config-if)#glbp 0 weighting track 4 d ? decrement Weighting decrement R3(config-if)#glbp 0 weighting track 4 dec R3(config-if)#glbp 0 weighting track 4 decrement 50 R3(config-if)#^Z R3# sh ru *Mar 2 03:32:44.357: %SYS-5-CONFIG_I: Configured from console by console R3# sh run int fa 0/0 Building configuration... Current configuration : 220 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 0 ip 180.40.7.132 glbp 0 weighting 100 lower 75 glbp 0 weighting track 4 decrement 50 end R3# R3#^x7 % Unknown command or computer name, or unable to find computer address R3# R3# RACK8AS>8 [Resuming connection 8 to r7 ... ] *Mar R7(config-if)#exit R7(config)#track 4 ip ? route IP route R7(config)#track 4 ip route 20/.1   .10.1.0  /24 re R7(config)#track 4 ip route 20.10.1.0/24 reachability R7(config-track)#int fa 0/1 R7(config-if)#glbp 0 ip 180.40.7.132 R7(config-if)# glbp 0 weighting 100 lower 75 R7(config-if)# glbp 0 weighting track 4 decrement 50 R7(config-if)# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no track 4 R3(config)#track 4 ip route 20.10.1.1~0   0/24 re R3(config-track)#do sh run int fa 0/1 0 Building configuration... Current configuration : 220 bytes ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 0 ip 180.40.7.132 glbp 0 weighting 100 lower 75 glbp 0 weighting track 4 decrement 50 end R3(config-track)#^Z R3# *Mar 2 03:34:24.264: %SYS-5-CONFIG_I: Configured from console by console R3#sh glbp FastEthernet0/0 - Group 0 State is Active 2 state changes, last state change 00:08:05 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 0.944 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is local Standby is 180.40.7.131, priority 100 (expires in 7.283 sec) Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 4 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Active 1 state change, last state change 00:07:55 MAC address is 0007.b400.0001 (default) Owner ID is 0012.8014.1900 Redirection enabled Preemption enabled, min delay 30 sec Active is local, weighting 100 --More--   Forwarder 2 State is Listen MAC address is 0007.b400.0002 (learnt) Owner ID is 0012.43ac.6e61 Redirection enabled, 597.900 sec remaining (maximum 600 sec) Time to live: 14397.900 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.131 (primary), weighting 100 (expires in 7.896 sec) R3# RACK8AS>8 [Resuming connection 8 to r7 ... ] * R7(config-if)#^Z R7#sh glbp FastEthernet0/1 - Group 0 State is Standby 1 state change, last state change 00:00:56 Virtual IP address is 180.40.7.132 Hello time 3 sec, hold time 10 sec Next hello sent in 0.371 secs Redirect time 600 sec, forwarder time-out 14400 sec Preemption disabled Active is 180.40.7.129, priority 100 (expires in 8.025 sec) Standby is local Priority 100 (default) Weighting 100 (configured 100), thresholds: lower 75, upper 100 Track object 4 state Up decrement 50 Load balancing: round-robin There are 2 forwarders (1 active) Forwarder 1 State is Listen MAC address is 0007.b400.0001 (learnt) Owner ID is 0012.8014.1900 Time to live: 14398.021 sec (maximum 14400 sec) Preemption enabled, min delay 30 sec Active is 180.40.7.129 (primary), weighting 100 (expires in 8.021 sec) Forwarder 2 --More-- *Mar 2 03:35:02.619: %SYS-5-CONFIG_I: Configured from console by console --More--   State is Active 1 state change, last state change 00:01:04 MAC address is 0007.b400.0002 (default) Owner ID is 0012.43ac.6e61 Preemption enabled, min delay 30 sec Active is local, weighting 100 R7# R7# R7# R7# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b track track 3 ip route 20.10.2.0 255.255.255.0 reachability ! track 4 ip route 20.10.1.0 255.255.255.0 reachability ! ! ! class-map match-all Telnet match protocol telnet class-map match-all FTP match protocol ftp ! ! policy-map Prob9 class FTP bandwidth percent 50 class Telnet bandwidth percent 25 class class-default bandwidth percent 25 ! ! ! ! --More--  ! ! interface FastEthernet0/0 ip address 180.40.7.129 255.255.255.224 ip policy route-map Prob1 duplex auto speed auto glbp 0 ip 180.40.7.132 glbp 0 weighting 100 lower 75 glbp 0 weighting track 4 decrement 50 ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.66 255.255.255.224 --More--   R3# RACK8AS>8 [Resuming connection 8 to r7 ... ] R7#sh ru | b rout         n | bg    te rac track 4 ip route 20.10.1.0 255.255.255.0 reachability ! ! ! class-map match-any JPEG match protocol http mime "*jpeg" match protocol http url "*.jpeg" match protocol http url "*.jpg" match protocol http url "*.jpe" class-map match-all S5Other match access-group 1 class-map match-all S5Telnet match access-group 1 match protocol telnet ! ! policy-map Prob6 class S5Telnet bandwidth 1000 class S5Other police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 --More--   class JPEG shape average 1000000 ! ! ! ! ! ! interface FastEthernet0/0 ip address 208.28.1.1 255.255.255.0 speed auto half-duplex ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.131 255.255.255.224 speed auto half-duplex glbp 0 ip 180.40.7.132 glbp 0 weighting 100 lower 75 --More--   glbp 0 weighting track 4 decrement 50 --More--   service-policy output Prob6 --More--  ! --More--  interface Serial1/0 --More--   R7# RACK8AS>6 [Resuming connection 6 to r6 ... ] 1 S6#sh in  run int fa 0 % Incomplete command. S6#4sh run int fa 0/4 Building configuration... Current configuration : 119 bytes ! interface FastEthernet0/4 switchport access vlan 10 switchport mode dynamic desirable spanning-tree portfast end S6#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Default DSCP Mutation Map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --More--   --------------------------------------- --More--   0 : 00 01 02 03 04 05 06 07 08 09 --More--   1 : 10 11 12 13 14 15 16 17 18 19 --More--   S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#mls qos ? aggregate-policer Assign aggregate policer cos Configure CoS setting map Define QoS mapping min-reserve Configure min-reserve buffers S6(config)#mls qos map ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S6(config)#mls qos map ip ? <0-63> 8 dscp values separated by spaces S6(config)#mls qos map ip 0 14 16 28 32 40 48 56 S6(config)#mls qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S6(config)#int fa 0/7 S6(config-if)#mls qos ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S6(config-if)#mls qos tr S6(config-if)#mls qos trust ? cos Classify by packet COS device trusted device class dscp Classify by packet DSCP ip-precedence Classify by packet IP precedence S6(config-if)#mls qos trust S6(config-if)#mls qos trust ip S6(config-if)#^Z S6# 1d03h: %SYS-5-CONFIG_I: Configured from console by console S6#sh run | b mls qos mls qos map ip-prec-dscp 0 14 16 28 32 40 48 56 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 no switchport ip address 20.10.2.1 255.255.255.0 ! interface FastEthernet0/2 --More--   no switchport ip address 20.10.1.2 255.255.255.0 ! interface FastEthernet0/3 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport access vlan 10 switchport mode dynamic desirable spanning-tree portfast ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 switchport access vlan 10 switchport mode dynamic desirable mls qos trust ip-precedence ! interface FastEthernet0/8 --More--   S6# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5(config)#mls qos QoS: ensure flow-control on all interfaces are OFF for proper operation. S5(config)#int fa 0/24 S5(config-if)#mls qos tru S5(config-if)#exit S5(config)#mls qos map ? cos-dscp Map COS to DSCP dscp-cos Map DSCP to COS dscp-mutation Configure dscp-mutation map dscp-switch-priority Map DSCP to switch priority ip-prec-dscp DSCP values for IP precedences 0-7 policed-dscp Map DSCP to policed DSCP S5(config)#mls qos map dsc S5(config)#mls qos map dscp-m S5(config)#mls qos map dscp-mutation ? WORD DSCP mutation map name S5(config)#mls qos map dscp-mutation 14 to 12 ^ % Invalid input detected at '^' marker. S5(config)#mls qos map dscp-mutation 14 to 12     ? <0-63> DSCP values separated by spaces (up to 8 values total) S5(config)#mls qos map dscp-mutation 14    Prob17 ? <0-63> DSCP values separated by spaces (up to 8 values total) S5(config)#mls qos map dscp-mutation Prob17 14 ? <0-63> DSCP values separated by spaces (up to 8 values total) to Specify egress DSCPs S5(config)#mls qos map dscp-mutation Prob17 14 to 12 S5(config)#mls qos map dscp-mutation Prob17 14 to 1214 to 12 Prob17 14 to 12        28 to 25 S5(config)#int fa 0/3 S5(config-if)#mls qos ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S5(config-if)#mls qos ds S5(config-if)#mls qos dscp-mutation Prob17 ? S5(config-if)#mls qos dscp-mutation Prob17   S5(config-if)#^Z S5# sh run | 1d04h: %SYS-5-CONFIG_I: Configured from console by console S5# sh run | b mls mls qos map dscp-mutation Prob17 14 to 12 mls qos map dscp-mutation Prob17 28 to 25 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! --More--  interface FastEthernet0/2 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/4 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/5 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/6 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/7 no switchport --More--   S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#class S5(config)#class-map AF13 S5(config-cmap)#match ? access-group Access group class-map Class map ip IP specific values vlan VLANs to match S5(config-cmap)#match ip ? dscp Match IP DSCP (DiffServ CodePoints) precedence Match IP precedence S5(config-cmap)#match ip dscp ? <0-63> Differentiated services codepoint value af11 Match packets with AF11 dscp (001010) af12 Match packets with AF12 dscp (001100) af13 Match packets with AF13 dscp (001110) af21 Match packets with AF21 dscp (010010) af22 Match packets with AF22 dscp (010100) af23 Match packets with AF23 dscp (010110) af31 Match packets with AF31 dscp (011010) af32 Match packets with AF32 dscp (011100) af33 Match packets with AF33 dscp (011110) af41 Match packets with AF41 dscp (100010) af42 Match packets with AF42 dscp (100100) af43 Match packets with AF43 dscp (100110) cs1 Match packets with CS1(precedence 1) dscp (001000) cs2 Match packets with CS2(precedence 2) dscp (010000) cs3 Match packets with CS3(precedence 3) dscp (011000) cs4 Match packets with CS4(precedence 4) dscp (100000) cs5 Match packets with CS5(precedence 5) dscp (101000) cs6 Match packets with CS6(precedence 6) dscp (110000) cs7 Match packets with CS7(precedence 7) dscp (111000) default Match packets with default dscp (000000) ef Match packets with EF dscp (101110) --More--   S5(config-cmap)#match ip dscp f   af13 ? <0-63> Differentiated services codepoint value af11 Match packets with AF11 dscp (001010) af12 Match packets with AF12 dscp (001100) af13 Match packets with AF13 dscp (001110) af21 Match packets with AF21 dscp (010010) af22 Match packets with AF22 dscp (010100) af23 Match packets with AF23 dscp (010110) af31 Match packets with AF31 dscp (011010) af32 Match packets with AF32 dscp (011100) af33 Match packets with AF33 dscp (011110) af41 Match packets with AF41 dscp (100010) af42 Match packets with AF42 dscp (100100) af43 Match packets with AF43 dscp (100110) cs1 Match packets with CS1(precedence 1) dscp (001000) cs2 Match packets with CS2(precedence 2) dscp (010000) cs3 Match packets with CS3(precedence 3) dscp (011000) cs4 Match packets with CS4(precedence 4) dscp (100000) cs5 Match packets with CS5(precedence 5) dscp (101000) cs6 Match packets with CS6(precedence 6) dscp (110000) cs7 Match packets with CS7(precedence 7) dscp (111000) default Match packets with default dscp (000000) ef Match packets with EF dscp (101110) --More--   --More--   S5(config-cmap)#match ip dscp af13 S5(config-cmap)#exit S5(config)#exitmatch ip dscp af13 class-map AF13    32 S5(config-cmap)#match ip dscp af31 2 S5(config-cmap)#exit S5(config)#pol S5(config)#policy-map S5(config)#policy-map Prob17 S5(config-pmap)#clas S5(config-pmap)#class AF13 S5(config-pmap-c)#? QoS policy-map class configuration commands: exit Exit from QoS class action configuration mode no Negate or set default values of a command police Police set Set QoS values trust Set trust value for the class S5(config-pmap-c)#set ? cos Set IEEE 802.1Q/ISL class of service/user priority dscp Set DSCP in IP(v4) and IPv6 packets ip Set IP specific values precedence Set precedence in IP(v4) and IPv6 packets S5(config-pmap-c)#set dscp ? <0-63> Differentiated services codepoint value af11 Match packets with AF11 dscp (001010) af12 Match packets with AF12 dscp (001100) af13 Match packets with AF13 dscp (001110) af21 Match packets with AF21 dscp (010010) af22 Match packets with AF22 dscp (010100) af23 Match packets with AF23 dscp (010110) af31 Match packets with AF31 dscp (011010) af32 Match packets with AF32 dscp (011100) af33 Match packets with AF33 dscp (011110) af41 Match packets with AF41 dscp (100010) af42 Match packets with AF42 dscp (100100) af43 Match packets with AF43 dscp (100110) cs1 Match packets with CS1(precedence 1) dscp (001000) cs2 Match packets with CS2(precedence 2) dscp (010000) cs3 Match packets with CS3(precedence 3) dscp (011000) cs4 Match packets with CS4(precedence 4) dscp (100000) cs5 Match packets with CS5(precedence 5) dscp (101000) cs6 Match packets with CS6(precedence 6) dscp (110000) cs7 Match packets with CS7(precedence 7) dscp (111000) default Match packets with default dscp (000000) ef Match packets with EF dscp (101110) --More--   S5(config-pmap-c)#set dscp af12 S5(config-pmap-c)#exit S5(config-pmap)#exitset dscp af12class AF13   32 2 S5(config-pmap-c)#set dscp af31 S5(config-pmap-c)#int fa 0/3 S5(config-if)#ser S5(config-if)#service-policy out prob17 policy map prob17 not configured S5(config-if)#service-policy out prob17rob17 Prob17 S5(config-if)# 1d04h: %QM-4-NOT_SUPPORTED: Action 'set' is not supported for a policymap attached to output side. 1d04h: %QM-4-NOT_SUPPORTED: Action 'set' is not supported for a policymap attached to output side. S5(config-if)#int fa 0/24 S5(config-if)#exit S5(config)#access-lisst  t 180   1 per 180.40.7.129 S5(config)#class S5(config)#class-map AF13 S5(config-cmap)#match ? access-group Access group class-map Class map ip IP specific values vlan VLANs to match S5(config-cmap)#match access S5(config-cmap)#match access-group 1 ? S5(config-cmap)#match access-group 1 QoS: Policy-map Prob17 failed checking. Policymap is detached from the interface(s). S5(config-cmap)# 1d04h: %QM-4-CLASS_NOT_SUPPORTED: Classification is not supported in classmap AF13 1d04h: %QM-4-CLASS_NOT_SUPPORTED: Classification is not supported in classmap AF13 1d04h: %QM-4-CLASS_NOT_SUPPORTED: Classification is not supported in classmap AF13 1d04h: %QM-4-ACTION_NOT_SUPPORTED: Action is not supported in policymap Prob17 S5(config-cmap)#int fa 0/3 S5(config-if)#no serv S5(config-if)#no service-policy out Prob17 Service Policy Prob17 not attached S5(config-if)#int fa 0/24 S5(config-if)#serv S5(config-if)#service-policy inb    Prob17 S5(config-if)# 1d04h: %QM-4-CLASS_NOT_SUPPORTED: Classification is not supported in classmap AF13 1d04h: %QM-4-CLASS_NOT_SUPPORTED: Classification is not supported in classmap AF13 1d04h: %QM-4-CLASS_NOT_SUPPORTED: Classification is not supported in classmap AF13 S5(config-if)#no class S5(config-if)#no class- S5(config-if)#no class-m S5(config-if)#no class-map AF13 Class-map AF13 is being used S5(config)#no class-map AF13  32 Class-map AF32 is being used S5(config)#no pol Prob17 % Ambiguous command: "no pol Prob17" S5(config)#no pol Prob17 Prob17        l S5(config)#no policy-map S5(config)#no policy-map   ? policy-manager policy-map S5(config)#no policy-map Prob17 S5(config)# 1d04h: %QM-4-CLASS_NOT_SUPPORTED: Classification is not supported in classmap AF13 1d04h: %QM-4-CLASS_NOT_SUPPORTED: Classification is not supported in classmap AF13 S5(config)#no policy-map Prob17 Prob17 class-map AF32 S5(config)#no class-map AF32policy-map Prob17 Prob17 class-map AF3213 S5(config)#^Z S5#sh 1d04h: %SYS-5-CONFIG_I: Configured from console by console S5#sh run Building configuration... Current configuration : 2896 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname S5 ! ! no aaa new-model mls qos map dscp-mutation Prob17 14 to 12 mls qos map dscp-mutation Prob17 28 to 25 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! --More--  ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/2 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/4 --More--   switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/5 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/6 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/7 no switchport ip address 208.28.1.2 255.255.255.0 mls qos dscp-mutation Prob17 ! interface FastEthernet0/8 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/9 switchport mode dynamic desirable mls qos dscp-mutation Prob17 --More--  ! interface FastEthernet0/10 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/11 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/12 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/13 switchport mode dynamic desirable ! interface FastEthernet0/14 switchport mode dynamic desirable ! interface FastEthernet0/15 switchport mode dynamic desirable ! interface FastEthernet0/16 --More--   switchport mode dynamic desirable ! interface FastEthernet0/17 switchport mode dynamic desirable ! interface FastEthernet0/18 switchport mode dynamic desirable ! interface FastEthernet0/19 switchport mode dynamic desirable ! interface FastEthernet0/20 switchport mode dynamic desirable ! interface FastEthernet0/21 switchport mode dynamic desirable ! interface FastEthernet0/22 switchport mode dynamic desirable ! interface FastEthernet0/23 switchport mode dynamic desirable ! --More--  interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk mls qos trust dscp ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ip http server ip http secure-server ! --More--   S5#onfig       config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/24 S5(config-if)# mls qos dscp-mutation Prob17 S5(config-if)#int f range fa 0/1   - 12 S5(config-if-range)#no mls qos dscp-mutation Prob17 S5(config-if-range)#^Z S5#sh run Building configuration... Current configuration : 2896 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname S5 ! ! no aaa new-model mls qos map dscp-mutation Prob17 14 to 12 mls qos map dscp-mutation Prob17 28 to 25 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! --More-- 1d04h: %SYS-5-CONFIG_I: Configured from console by console --More--  ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport mode dynamic desirable ! interface FastEthernet0/2 switchport mode dynamic desirable ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport mode dynamic desirable ! interface FastEthernet0/5 --More--   switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 no switchport ip address 208.28.1.2 255.255.255.0 ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable --More--  ! interface FastEthernet0/13 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/14 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/15 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/16 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/17 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/18 switchport mode dynamic desirable --More--   mls qos dscp-mutation Prob17 ! interface FastEthernet0/19 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/20 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/21 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/22 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/23 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/24 --More--   switchport trunk encapsulation dot1q switchport mode trunk mls qos trust dscp mls qos dscp-mutation Prob17 ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ip http server ip http secure-server ! --More--  ! access-list 1 permit 180.40.7.129 ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous line vty 0 4 privilege level 15 no login line vty 5 15 no login ! ! end S5# S5# S5# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#DEB IP ? address IP address activity audit IDS audit events auth-proxy Authentication proxy debug bgp BGP information cache IP cache operations cef IP CEF operations cgmp CGMP protocol activity dhcp Dynamic Host Configuration Protocol director Director agent information drp Director response protocol dvmrp DVMRP protocol activity eigrp IP-EIGRP information error IP error debugging flow IP Flow switching operations ftp FTP dialogue html HTML connections http HTTP connections icmp ICMP transactions igmp IGMP protocol activity inspect Stateful inspection events interface IP interface configuration changes mbgp MBGP information --More--   mcache IP multicast cache operations mhbeat IP multicast heartbeat monitoring mobile IP Mobility mpacket IP multicast packet debugging mrm IP Multicast Routing Monitor mrouting IP multicast routing table activity msdp Multicast Source Discovery Protocol (MSDP) mtag IP multicast tagswitching activity nat NAT events nbar StILE - traffic classification Engine ospf OSPF information packet General IP debugging and IPSO security transactions peer IP peer address activity pgm PGM Reliable Transport Protocol pim PIM protocol activity policy Policy routing postoffice PostOffice audit events rgmp RGMP protocol activity rip RIP protocol transactions routing Routing table events rsvp RSVP protocol activity rtp RTP information scp Secure Copy --More--   sctp SCTP information sd Session Directory (SD) security IP security options snat Stateful NAT events socket Socket event ssh Incoming ssh connections tcp TCP information tempacl IP temporary ACL trigger-authentication Trigger authentication udp UDP based transactions urd URL RenDezvous (URD) urlfilter IOS URL filter events wccp WCCP information R3#DEB IP PACK DE`  IP packet debugging is on (detailed) R3# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#ping 180.40.7.; 129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Mar 2 04:19:26.823: IP: s=208.28.1.2 (FastEthernet0/0), d=180.40.7.129 (FastEthernet0/0), len 100, rcvd 3 *Mar 2 04:19:26.823: ICMP type=8, code=0 *Mar 2 04:19:26.823: IP: tableid=0, s=180.40.7.129 (local), d=208.28.1.2 (FastEthernet0/0), routed via FIB *Mar 2 04:19:26.823: IP: s=180.40.7.129 (local), d=208.28.1.2 (FastEthernet0/0), len 100, sending *Mar 2 04:19:26.823: ICMP type=0, code=0 *Mar 2 04:19:26.827: IP: tableid=0, s=208.28.1.2 (FastEthernet0/0), d=180.40.7.129 (FastEthernet0/0), routed via RIB *Mar 2 04:19:26.827: IP: s=208.28.1.2 (FastEthernet0/0), d=180.40.7.129 (FastEthernet0/0), len 100, rcvd 3 *Mar 2 04:19:26.827: ICMP type=8, code=0 *Mar 2 04:19:26.827: IP: tableid=0, s=180.40.7.129 (local), d=208.28.1.2 (FastEthernet0/0), routed via FIB *Mar 2 04:19:26.831: IP: s=180.40.7.129 (local), d=208.28.1.2 (FastEthernet0/0), len 100, sending *Mar 2 04:19:26.831: ICMP type=0, code=0 *Mar 2 04:19:26.831: IP: tableid=0, s=208.28.1.2 (FastEthernet0/0), d=180.40.7.129 (FastEthernet0/0), routed via RIB *Mar 2 04:19:26.831: IP: s=208.28.1.2 (FastEthernet0/0), d=180.40.7.129 (FastEthernet0/0), len 100, rcvd 3 *Mar 2 04:19:26.835: ICMP type=8, code=0 *Mar 2 04:19:26.835: IP: tableid=0, s=180.40.7.129 (local), d=208.28.1.2 (FastEthernet0/0), routed via FIB *Mar 2 04:19:26.835: IP: s=180.40.7.129 (local), d=208.28.1.2 (FastEthernet0/0), len 100, sending *Mar 2 04:19:26.835: ICMP type=0, code=0 *Mar 2 04:19:27.327: IP: s=180.40.7.65 (Serial1/0), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 2 04:19:28.177: IP: s=180.40.7.67 (Serial1/0), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 2 04:19:29.251: IP: s=180.40.7.66 (local), d=224.0.0.5 (Serial1/0), len 84, sending broad/multicast, proto=89 *Mar 2 04:19:29.299: IP: s=180.40.7.131 (FastEthernet0/0), d=224.0.0.102, len 88, rcvd 2 *Mar 2 04:19:29.299: UDP src=3222, dst=3222 *Mar 2 04:19:29.331: IP: s=180.40.7.131 (FastEthernet0/0), d=224.0.0.5, len 84, rcvd 0, proto=89 *Mar 2 04:19:29.815: IP: s=180.40.7.129 (local), d=224.0.0.102 (FastEthernet0/0), len 88, sending broad/multicast *Mar 2 04:19:29.815: UDP src=3222, dst=3222 *Mar 2 04:19:29.920: IP: s=180.40.7.130 (FastEthernet0/0), d=224.0.0.5, len 84, rcvd 0, proto=89 R3# R3#u all All possible debugging has been turned off R3# *Mar 2 04:19:32.300: IP: s=180.40.7.131 (FastEthernet0/0), d=224.0.0.102, len 88, rcvd 2 *Mar 2 04:19:32.300: UDP src=3222, dst=3222 *Mar 2 04:19:32.816: IP: s=180.40.7.129 (local), d=224.0.0.102 (FastEthernet0/0), len 88, sending broad/multicast *Mar 2 04:19:32.816: UDP src=3222, dst=3222 *Mar 2 04:19:33.213: IP: s=180.40.7.2 (Serial1/2), d=224.0.0.5, len 80, rcvd 0, proto=89 R3# R3#deb      RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#sdh    h mls ? qos Show QoS information S5#sh mls qos ? aggregate-policer Show aggregate-policer information interface Show interface information maps Show mapping information | Output modifiers S5#sh mls qos QoS is enabled S5#sh mls qos int fa 0/25 ^ % Invalid input detected at '^' marker. S5#sh mls qos int fa 0/25 4sh mls qos int fa 0/25 4 FastEthernet0/24 trust state: trust dscp trust mode: trust dscp COS override: dis default COS: 0 DSCP Mutation Map: Prob17 Trust device: none S5#sh mls qos int fa 0/24 ? buffers Show buffer information policers Show policers information queueing Show queueing information statistics Show statistics | Output modifiers S5#sh mls qos int fa 0/24 sta S5#sh mls qos int fa 0/24 statistics FastEthernet0/24 Ingress dscp: incoming no_change classified policed dropped (in bytes) Others: 97872 96964 908 0 0 Egress dscp: incoming no_change classified policed dropped (in bytes) Others: 7496988 n/a n/a 0 0 S5#sh mls qos int fa 0/24 statistics   sh mls qos int fa 0/24 statistics  sh mls qos int fa 0/24 statistics FastEthernet0/24 Ingress dscp: incoming no_change classified policed dropped (in bytes) Others: 101345 100437 908 0 0 Egress dscp: incoming no_change classified policed dropped (in bytes) Others: 7742213 n/a n/a 0 0 S5#sh mls qos int fa 0/24 statistics  5 ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129sh mls qos int fa 0/24 statistics FastEthernet0/24 Ingress dscp: incoming no_change classified policed dropped (in bytes) Others: 102691 101193 1498 0 0 Egress dscp: incoming no_change classified policed dropped (in bytes) Others: 7805189 n/a n/a 0 0 S5#sh mls qos int fa 0/24 statistics ? | Output modifiers S5#sh mls qos int fa 0/24 statistics                        ? aggregate-policer Show aggregate-policer information interface Show interface information maps Show mapping information | Output modifiers S5#sh mls qos mP ? % Unrecognized command S5#sh mls qos mP   AP ? cos-dscp Show COS to DSCP map dscp-cos Show DSCP to COS map dscp-mutation Show dscp-mutation map dscp-switch-priority Show DSCP to switch priority map ip-prec-dscp Show IP precedence to DSCP map policed-dscp Show DSCP to policed mark down DSCP map | Output modifiers S5#sh mls qos mAP dsc S5#sh mls qos mAP dscp-m S5#sh mls qos mAP dscp-mutation ? WORD dscp-mutation map name | Output modifiers S5#sh mls qos mAP dscp-mutation Dscp-dscp mutation map: Prob17: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 12 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 25 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-dscp mutation map: Default DSCP Mutation Map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 --More--   S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol R3#sh policy-map Policy Map Prob9 Class FTP Bandwidth 50 (%) Max Threshold 64 (packets) Class Telnet Bandwidth 25 (%) Max Threshold 64 (packets) Class class-default Bandwidth 25 (%) Max Threshold 64 (packets) R3#sh pol int fa 0/0 R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class   R3(config)#class-map m AF12 R3(config-cmap)#match R3(config-cmap)#match ip dsc R3(config-cmap)#match ip dscp AF12 R3(config-cmap)#match ip dscp AF12class-map AF12 do sh run int fa 0/0class-map AF12   31 R3(config-cmap)#class-map AF31match ip dscp AF12  31 R3(config-cmap)#pol Prob17Test R3(config-pmap)#class AF12 R3(config-pmap-c)#class AF12 do sh pol Policy Map Prob9 Class FTP Bandwidth 50 (%) Max Threshold 64 (packets) Class Telnet Bandwidth 25 (%) Max Threshold 64 (packets) Class class-default Bandwidth 25 (%) Max Threshold 64 (packets) Policy Map Prob17Test Class AF12 R3(config-pmap-c)#do sh polclass AF12do sh pol  exit R3(config-pmap)#exitdo sh polclass AF12  31 R3(config-pmap-c)#int fa 0/0 R3(config-if)#serv R3(config-if)#service-policy Prob17Test iProb17Test nProb17Test  Prob17Test  R3(config-if)#^Z R3#s *Mar 2 04:24:44.744: %SYS-5-CONFIG_I: Configured from console by console R3#sh pi ol int fa 0/0 FastEthernet0/0 Service-policy input: Prob17Test Class-map: AF12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af12 (12) Class-map: AF31 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af31 (26) Class-map: class-default (match-any) 5 packets, 502 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#sh mls qos mAP dscp-mutation int fa 0/24 statistics ping 180.40.7.129  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: Prob17Test Class-map: AF12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af12 (12) Class-map: AF31 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af31 (26) Class-map: class-default (match-any) 26 packets, 2816 bytes 5 minute offered rate 1000 bps, drop rate 0 bps Match: any R3# R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#classn  R3(config)#class-map AF32 R3(config-cmap)#match ip dcp af32 ^ % Invalid input detected at '^' marker. R3(config-cmap)#match ip dcp af32scp af32 R3(config-cmap)#class-map AF13 R3(config-cmap)#match ip dscp af13 R3(config-cmap)#pol prob17Trob17T Prob17Trob17Test R3(config-pmap)#class af  af1   AF13 R3(config-pmap-c)#class AF13  32 R3(config-pmap-c)#^Z R3#sg h *Mar 2 04:26:29.539: %SYS-5-CONFIG_I: Configured from console by console R3#sh pol Policy Map Prob9 Class FTP Bandwidth 50 (%) Max Threshold 64 (packets) Class Telnet Bandwidth 25 (%) Max Threshold 64 (packets) Class class-default Bandwidth 25 (%) Max Threshold 64 (packets) Policy Map Prob17Test Class AF12 Class AF31 Class AF13 Class AF32 R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: Prob17Test Class-map: AF12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af12 (12) Class-map: AF31 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af31 (26) Class-map: AF13 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af13 (14) Class-map: AF32 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af32 (28) --More--   Class-map: class-default (match-any) 75 packets, 7742 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#ping 180.40.7.129sh mls qos mAP dscp-mutation Dscp-dscp mutation map: Prob17: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 12 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 25 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-dscp mutation map: Default DSCP Mutation Map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 --More--   S5#[Bqsh mls qos mAP dscp-mutation ping 180.40.7.129  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: Prob17Test Class-map: AF12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af12 (12) Class-map: AF31 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af31 (26) Class-map: AF13 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af13 (14) Class-map: AF32 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af32 (28) --More--   Class-map: class-default (match-any) 96 packets, 10056 bytes 5 minute offered rate 1000 bps, drop rate 0 bps Match: any R3# RACK8AS>7 8 [Resuming connection 8 to r7 ... ] R7#sh pol Policy Map Prob6 Class S5Telnet Bandwidth 1000 (kbps) Max Threshold 64 (packets) Class S5Other police cir 5000000 bc 156250 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1 Class JPEG Traffic Shaping Average Rate Traffic Shaping CIR 1000000 (bps) Max. Buffers Limit 1000 (Packets) R7#sh pol int fa 0/1 FastEthernet0/1 Service-policy output: Prob6 Class-map: S5Telnet (match-all) 21 packets, 1178 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 1 Match: protocol telnet Queueing Output Queue: Conversation 265 Bandwidth 1000 (kbps) Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 Class-map: S5Other (match-all) 45 packets, 5130 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: access-group 1 police: cir 5000000 bps, bc 156250 bytes conformed 45 packets, 5130 bytes; actions: set-prec-transmit 3 --More--   exceeded 0 packets, 0 bytes; actions: set-prec-transmit 1 conformed 0 bps, exceed 0 bps Class-map: JPEG (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol http mime "*jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpeg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpg" 0 packets, 0 bytes 5 minute rate 0 bps Match: protocol http url "*.jpe" 0 packets, 0 bytes 5 minute rate 0 bps Traffic Shaping Target/Average Byte Sustain Excess Interval Increment Rate Limit bits/int bits/int (ms) (bytes) 1000000/1000000 6250 25000 25000 25 3125 --More--   R7#^x6 % Unknown command or computer name, or unable to find computer address R7# R7# RACK8AS>6 [Resuming connection 6 to r6 ... ] S6#sh run int fa 0/7 Building configuration... Current configuration : 124 bytes ! interface FastEthernet0/7 switchport access vlan 10 switchport mode dynamic desirable mls qos trust ip-precedence end S6# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class Pre2 ^ % Invalid input detected at '^' marker. R3(config)#class Pre2 3- Pre3m Pre3a Pre3p Pre3 R3(config-cmap)#match ? access-group Access group any Any packets class-map Class map cos IEEE 802.1Q/ISL class of service/user priority values destination-address Destination address discard-class Discard behavior identifier dscp Match DSCP in IP(v4) and IPv6 packets fr-de Match on Frame-relay DE bit fr-dlci Match on fr-dlci input-interface Select an input interface to match ip IP specific values mpls Multi Protocol Label Switching specific values not Negate this match result packet Layer 3 Packet length precedence Match Precedence in IP(v4) and IPv6 packets protocol Protocol qos-group Qos-group source-address Source address R3(config-cmap)#match ip ? dscp Match IP DSCP (DiffServ CodePoints) precedence Match IP precedence rtp Match RTP port nos R3(config-cmap)#match ip pre R3(config-cmap)#match ip precedence 3 R3(config-cmap)#match ip precedence 3class-map Pre3  Pre2 AF3213pol Prob17Test R3(config-pmap)#class Pre3 R3(config-pmap-c)#^Z R3# RACK8AS>5 [Resuming connection 5 to r5 ... ] ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#config t gtsh pol int fa 0/0 FastEthernet0/0 Service-policy input: Prob17Test Class-map: AF12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af12 (12) Class-map: AF31 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af31 (26) Class-map: AF13 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af13 (14) Class-map: AF32 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af32 (28) --More--   Class-map: Pre3 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: class-default (match-any) 165 packets, 16990 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3#x  RACK8AS>6 [Resuming connection 6 to r6 ... ] S6#co  sh run     n int fa 0/7 Building configuration... Current configuration : 124 bytes ! interface FastEthernet0/7 switchport access vlan 10 switchport mode dynamic desirable mls qos trust ip-precedence end S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#mls qos tr ^ % Invalid input detected at '^' marker. S6(config)#mls qos tr  int fa 0/6 S6(config-if)#int fa 0/6 7 S6(config-if)#int fa 0/76mls qos tr S6(config-if)# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | i mls qos mls qos map dscp-mutation Prob17 14 to 12 mls qos map dscp-mutation Prob17 28 to 25 mls qos mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos trust dscp mls qos dscp-mutation Prob17 S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh    config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class-map DSCP25 R3(config-cmap)#match ip dscp 25 R3(config-cmap)#match ip dscp 25class-map DSCP25 Pre3 pol Prob17Test R3(config-pmap)#class P DSCP25 R3(config-pmap-c)#^Z R3# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | i mls qosping 180.40.7.129  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Mconfig tsh pol int fa 0/0 FastEthernet0/0 Service-policy input: Prob17Test Class-map: AF12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af12 (12) Class-map: AF31 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af31 (26) Class-map: AF13 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af13 (14) Class-map: AF32 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af32 (28) --More--   Class-map: Pre3 (match-all) 15 packets, 1710 bytes 5 minute offered rate 0 bps Match: ip precedence 3 Class-map: DSCP25 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp 25 Class-map: class-default (match-any) 304 packets, 30912 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK8AS>6 [Resuming connection 6 to r6 ... ] S6(config-if)#int fa 0/3 S6(config-if)#mls qos ? cos Configure interface COS parameters dscp-mutation Apply DSCP-DSCP map to DSCP trusted port monitor Collect QoS statistics trust Configure trust state of interface S6(config-if)#mls qos int fa 0/3 7 S6(config-if)#int fa 0/7  RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#class DSCP25pol Prob17Test R3(config-pmap)#no class Pre3 R3(config-pmap)#^Z R3# *Mar 2 04:34:22.631: %SY RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] S-5-CONFIG_I: Configured from console by console R3# R3#config tsh pol int fa 0/0 FastEthernet0/0 Service-policy input: Prob17Test Class-map: AF12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af12 (12) Class-map: AF31 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af31 (26) Class-map: AF13 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af13 (14) Class-map: AF32 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af32 (28) --More--   Class-map: DSCP25 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp 25 Class-map: class-default (match-any) 351 packets, 35702 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK8AS>6 [Resuming connection 6 to r6 ... ] S6(config-if)#^Z S6# 1d04h: %SYS-5-CONFIG_I: Configured from console by console S6#wr Building configuration... [OK] S6#reload Proceed with reload? [confirm] 1d04h: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command. 1d04h: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on FastEthernet0/2 from FULL to DOWN, Neighbor Down: Interface down or detached 1d04h: %OSPF-5-ADJCHG: Process 1, Nbr 20.10.2.2 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detachedBase ethernet MAC Address: 00:11:92:12:ed:80 Xmodem file system is available. The password-recovery mechanism is enabled. Initializing Flash... flashfs[0]: 81 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 15998976 flashfs[0]: Bytes used: 9976320 flashfs[0]: Bytes available: 6022656 flashfs[0]: flashfs fsck took 18 seconds. ...done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Loading "flash:a.bin"...flash:a.bin: no such file or directory Error loading "flash:a.bin" Interrupt within 5 seconds to abort boot process. Loading "flash:/c3550-ipservicesk9-mz.122-25.SED.bin"...############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################# File "flash:/c3550-ipservicesk9-mz.122-25.SED.bin" uncompressed and installed, entry point: 0x3000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(25)SED, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Sat 22-Oct-05 12:14 by yenanh Image text-base: 0x00003000, data-base: 0x00D6EDC8 Initializing flashfs... flashfs[1]: 81 files, 4 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 15998976 flashfs[1]: Bytes used: 9976320 flashfs[1]: Bytes available: 6022656 flashfs[1]: flashfs fsck took 9 seconds. flashfs[1]: Initialization complete. ...done Initializing flashfs. POST: CPU Buffer Tests : Begin POST: CPU Buffer Tests : End, Status Passed POST: CPU Interface Tests : Begin POST: CPU Interface Tests : End, Status Passed POST: Switch Core Tests : Begin POST: Switch Core Tests : End, Status Passed POST: CPU Interface 2nd Stage Tests : Begin POST: CPU Interface 2nd Stage Tests : End, Status Passed POST: CAM Subsystem Tests : Begin POST: CAM Subsystem Tests : End, Status Passed POST: Ethernet Controller Tests : Begin POST: Ethernet Controller Tests : End, Status Passed POST: ILP Controller Tests : Begin POST: ILP Controller Tests : End, Status Passed POST: Loopback Tests : Begin POST: Loopback Tests : End, Status Passed This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. Cisco WS-C3550-24-PWR (PowerPC) processor (revision G0) with 65526K/8192K bytes of memory. Processor board ID CAT0825Z0GL Last reset from warm-reset Running Layer2/3 Switching Image Ethernet-controller 1 has 12 Fast Ethernet/IEEE 802.3 interfaces Ethernet-controller 2 has 12 Fast Ethernet/IEEE 802.3 interfaces Ethernet-controller 3 has 1 Gigabit Ethernet/IEEE 802.3 interface Ethernet-controller 4 has 1 Gigabit Ethernet/IEEE 802.3 interface 24 FastEthernet interfaces 2 Gigabit Ethernet interfaces The password-recovery mechanism is enabled. 384K bytes of flash-simulated NVRAM. Base ethernet MAC Address: 00:11:92:12:ED:80 Motherboard assembly number: 73-8100-08 Power supply part number: 341-0029-03 Motherboard serial number: CAT082408FR Power supply serial number: DTH08201YRN Model revision number: G0 Motherboard revision number: A0 Model number: WS-C3550-24PWR-EMI System serial number: CAT0825Z0GLFailed to generate persistent self-signed certificate. Secure server will use temporary self-signed certificate.  Press RETURN to get started! 00:00:38: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan 00:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down 00:00:40: %SYS-5-CONFIG_I: Configured from memory by console 00:00:41: %SYS-5-RESTART: System restarted -- Cisco IOS Software, C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(25)SED, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Sat 22-Oct-05 12:14 by yenanh 00:00:42: %LINK-5-CHANGED: Interface Vlan1, S6> S6>changed state to administratively down 00:00:44: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up 00:00:44: %LINK-3-UPDOWN: Interface FastEthernet0/4, changed state to up 00:00:44: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to up 00:00:44: %LINK-3-UPDOWN: Interface FastEthernet0/24, changed state to up 00:00:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up 00:00:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, cha S6>nged state to down 00:00:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down 00:00:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down 00:00:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down 00:00:46: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down S6> 00:00:47: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up 00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up S6>en S6# 00:00:49: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up S6#sh run int 00:00:50: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up 00:00:50: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to up 00:00:51: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up S6#sh run int fa 0/7 Building configuration... Current configuration : 115 bytes ! interface FastEthernet0/7 switchport access vlan 10 switchport mode dynamic desirable mls qos trust dscp end S6#sh run int fa 0/7en sh run int fa 0/7 config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/7 S6(config-if)#mls qis tr       os ip S6(config-if)#mls qos ip? % Unrecognized command S6(config-if)#mls qos ip  tr S6(config-if)#mls qos trust ? cos Classify by packet COS device trusted device class dscp Classify by packet DSCP ip-precedence Classify by packet IP precedence S6(config-if)#mls qos trust ip S6(config-if)# 00:01:30: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on FastEthernet0/2 from LOADING to FULL, Loading Done S6(config-if)# RACK8AS>5 [Resuming connection 5 to r5 ... ] 1d S5#ping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/31/32 ms S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] *Mar R3# *Mar 2 04:44:36.369: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/0 from LOADING to FULL, Loading Done R3#sh pol int fa 0/0config t sh pol int fa 0/0 FastEthernet0/0 Service-policy input: Prob17Test Class-map: AF12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af12 (12) Class-map: AF31 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af31 (26) Class-map: AF13 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af13 (14) Class-map: AF32 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af32 (28) --More--   Class-map: DSCP25 (match-all) 5 packets, 570 bytes 5 minute offered rate 0 bps Match: ip dscp 25 Class-map: class-default (match-any) 620 packets, 63264 bytes 5 minute offered rate 2000 bps, drop rate 0 bps Match: any R3# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | b mls mls qos map dscp-mutation Prob17 14 to 12 mls qos map dscp-mutation Prob17 28 to 25 mls qos ip subnet-zero ip routing no ip domain-lookup ! ! ! ! ! ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! ! interface FastEthernet0/1 switchport mode dynamic desirable ! interface FastEthernet0/2 --More--   switchport mode dynamic desirable ! interface FastEthernet0/3 switchport access vlan 10 switchport mode dynamic desirable ! interface FastEthernet0/4 switchport mode dynamic desirable ! interface FastEthernet0/5 switchport mode dynamic desirable ! interface FastEthernet0/6 switchport mode dynamic desirable ! interface FastEthernet0/7 no switchport ip address 208.28.1.2 255.255.255.0 ! interface FastEthernet0/8 switchport mode dynamic desirable ! interface FastEthernet0/9 --More--   switchport mode dynamic desirable ! interface FastEthernet0/10 switchport mode dynamic desirable ! interface FastEthernet0/11 switchport mode dynamic desirable ! interface FastEthernet0/12 switchport mode dynamic desirable ! interface FastEthernet0/13 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/14 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/15 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! --More--  interface FastEthernet0/16 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/17 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/18 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/19 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/20 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/21 switchport mode dynamic desirable mls qos dscp-mutation Prob17 --More--  ! interface FastEthernet0/22 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/23 switchport mode dynamic desirable mls qos dscp-mutation Prob17 ! interface FastEthernet0/24 switchport trunk encapsulation dot1q switchport mode trunk mls qos trust dscp mls qos dscp-mutation Prob17 ! interface GigabitEthernet0/1 switchport mode dynamic desirable ! interface GigabitEthernet0/2 switchport mode dynamic desirable ! interface Vlan1 no ip address --More--   S5# S5#sh run | b mlsping 180.40.7.129 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 180.40.7.129, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms S5# RACK8AS>3 [Resuming connection 3 to r3 ... ] R3#sh pol int fa 0/0 FastEthernet0/0 Service-policy input: Prob17Test Class-map: AF12 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af12 (12) Class-map: AF31 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af31 (26) Class-map: AF13 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af13 (14) Class-map: AF32 (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps Match: ip dscp af32 (28) --More--   Class-map: DSCP25 (match-all) 10 packets, 1140 bytes 5 minute offered rate 0 bps Match: ip dscp 25 Class-map: class-default (match-any) 689 packets, 70198 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any R3# RACK8AS>5 [Resuming connection 5 to r5 ... ] S5#sh run | i mls qos mls qos map dscp-mutation Prob17 14 to 12 mls qos map dscp-mutation Prob17 28 to 25 mls qos mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos dscp-mutation Prob17 mls qos trust dscp mls qos dscp-mutation Prob17 S5#q config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#no mls qos map dscp-mutation Prob17 28 to 25 S5(config)#no mls qos map dscp-mutation Prob17 28 to 25 6no mls qos map dscp-mutation Prob17 28 to 26  mls qos map dscp-mutation Prob17 28 to 26  S5(config)#^Z S5# 1d04h: %SYS-5-CONFIG_I: Configured from console by console S5# [Connection to r5 closed by foreign host] RACK8AS>