=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.08.24 17:34:28 =~=~=~=~=~=~=~=~=~=~=~= sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/1 R 180.40.7.32 [120/1] via 180.40.7.2, 00:00:09, FastEthernet0/1 R 180.40.7.64 [120/2] via 180.40.7.2, 00:00:09, FastEthernet0/1 R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#sh config t ^ % Invalid input detected at '^' marker. R1#ip    config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv R1(config)#ipv6 u R1(config)#ipv6 unicast-routing R1(config)#int e 0/1 R1(config-if)#ipv add R1(config-if)#ipv address 2005:0:104::1/64 R1(config-if)#do sh ipv int brie Ethernet0/0 [up/up] unassigned Serial0/0 [administratively down/down] unassigned Ethernet0/1 [up/up] FE80::202:FDFF:FE79:C2A1 2005:0:104::1 Serial0/1 [up/up] unassigned R1(config-if)#int s 1 0/1 R1(config-if)#int s 0/1do sh ipv int brieipv address 2005:0:104::1/64::1/64 2::1/64 R1(config-if)# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#config Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ipv u R4(config)#ipv unicast-routing R4(config)#int fa 0/0 R4(config-if)#ip  v add R4(config-if)#ipv address 2005:0:102 4::4  /5 64 R4(config-if)#int atm 0 1/09  R4(config-if)#shut R4(config-if)#no ip add R4(config-if)#no ip address R4(config-if)# *Mar 1 20:47:58.322: %LINK-5-CHANGED: Interface ATM1/0, changed state to administratively down *Mar 1 20:47:59.322: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down R4(config-if)#int lo 0 R4(config-if)#ip  v add 200-0  0:4:4::4/64 R4(config-if)#^Z R4# *Mar 1 20:48:47.682: %SYS-5-CONFIG_I: Configured from console by console R4#pin 2005:0:104::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/9/20 ms R4# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/1 R2(config-if)#int s 1/1ip           eix  i xity ^ % Invalid input detected at '^' marker. R2(config-if)#~ ipv add 2005:0:>10   102::2/64 R2(config-if)#int s 1/2 R2(config-if)#int s 1/2pv add 2005:0:102::2/64::2/64 ::2/64 2::2/640::2/644::2/64::2/64 3::2/64 R2(config-if)#ipv add 2005:0:1203::2/64nt s 1/2  0.1 R2(config-subif)#int s 1/0.1pv add 2005:0:1203::2/64::2/64 ::2/64 ::2/64 ::2/64 2::2/643::2/647::2/64 R2(config-subif)#ipv add 2005:0:237::2/64nt s 1/0.1  2 R2(config-subif)#int s 1/0.2pv add 2005:0:237::2/64::2/64 ::2/64 ::2/64 7::2/649::2/642::2/64 R2(config-subif)#ipv add 2005:0:792::2/64nipv add 2005:0:792::2/64oipv add 2005:0:792::2/64 ipv add 2005:0:792::2/64 R2(config-subif)#no ipv add 2005:0:792::2/64ipv add 2005:0:792::2/64 2::2/64 02::2/64 R2(config-subif)#do sh run int s 1/0.1 Building configuration... Current configuration : 110 bytes ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::2/64 frame-relay interface-dlci 203 end R2(config-subif)#do sh run int s 1/0.1 2 Building configuration... Current configuration : 110 bytes ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::2/64 frame-relay interface-dlci 207 end R2(config-subif)#^Z R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# RACK12AS>2 [Resuming connection 2 to r2 ... ] * R2#co  sh ipv route IPv6 Routing Table - 10 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] --More--   via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipv R2(config)#ipv6 u R2(config)#ipv6 unicast-routing R2(config)#^Z R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config)#c ipv u R3(config)#ipv unicast-routing R3(config)#int s 1/2 R3(config-if)#ipv add 2005:0:1203::3/64 R3(config-if)#ipv add 2005:0:1203::3/64nt s 1/2  0 R3(config-if)#int s 1/0pv add 2005:0:1203::3/64::3/64 ::3/64 ::3/64 ::3/64 2::3/643::3/647::3/64 R3(config-if)#ipv add 2005:0:237::3/64nt s 1/0      lo 0 R3(config-if)#int lo 0pv add 2005:0:237::3/64::3/64 ::3/64 ::3/64 :3/64 ::3/64 :3/64 ::3/64 0::3/64:::3/643::3/64:::3/643::3/64 R3(config-if)# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv u R7(config)#ipv unicast-routing R7(config)#int s 1/0.1 R7(config-subif)#ipv add 2005:0:237::7/64 R7(config-subif)#ipv add 2005:0:237::7/64nt s 1/0.1 pv unicast-routing nt s 1/0.1  2 R7(config-subif)#int s 1/0.2pv add 2005:0:237::7/64::7/64 ::7/64 ::7/64 7::7/640::7/642::7/64 R7(config-subif)# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh iu nt s 1/0 Serial1/0 is up, line protocol is up Hardware is CD2430 in sync mode MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 7493, LMI stat recvd 7494, LMI upd recvd 0, DTE LMI up LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0 Last input 00:00:06, output 00:00:06, output hang never Last clearing of "show interface" counters 20:49:01 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 9998 packets input, 1005446 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles --More--   R3(config-if)#do sh int s 1/0rint s 1/0uint s 1/0nint s 1/0 int s 1/0 Building configuration... Current configuration : 100 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 end R3(config-if)#int s 1/0 R3(config-if)#fram map ipv 2005:0:237::7 307 R3(config-if)#fram map ipv 2005:0:237::7 307 br R3(config-if)#fram map ipv 2005:0:237::7 307 broadcast R3(config-if)#fram map ipv 2005:0:237::7 307 broadcast \ broadcast  broadcast 2 broadcast  broadcast  broadcast 2 broadcast  302 broadcast 2 302 broadcast  R3(config-if)#do p 2005:0:237::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R3(config-if)#do p 2005:0:237::2 7 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3(config-if)#ipv add 200   fe80::3 li R3(config-if)#ipv add fe80::3 link-local R3(config-if)#do sh run     ipv int brie FastEthernet0/0 [administratively down/down] unassigned BRI0/0 [administratively down/down] unassigned BRI0/0:1 [administratively down/down] unassigned BRI0/0:2 [administratively down/down] unassigned FastEthernet0/1 [up/up] unassigned Serial1/0 [up/up] FE80::3 2005:0:237::3 Serial1/1 [administratively down/down] unassigned Serial1/2 [up/up] FE80::212:80FF:FE14:1A00 2005:0:1203::3 Serial1/3 [administratively down/down] unassigned Serial1/4 [administratively down/down] unassigned Serial1/5 [administratively down/down] --More--   unassigned Serial1/6 [administratively down/down] unassigned Serial1/7 [administratively down/down] unassigned Loopback0 [up/up] FE80::212:80FF:FE14:1A00 2000:3:3::3 R3(config-if)# RACK12AS>2 [Resuming connection 2 to r2 ... ] *M R2#confi g ^ % Invalid input detected at '^' marker. R2#sh ipv int brie FastEthernet0/0 [administratively down/down] unassigned BRI0/0 [administratively down/down] unassigned BRI0/0:1 [administratively down/down] unassigned BRI0/0:2 [administratively down/down] unassigned FastEthernet0/1 [administratively down/down] unassigned Serial1/0 [up/up] unassigned Serial1/0.1 [up/up] FE80::212:80FF:FE14:4D00 2005:0:237::2 Serial1/0.2 [up/up] FE80::212:80FF:FE14:4D00 2005:0:702::2 Serial1/1 [up/up] FE80::212:80FF:FE14:4D00 2005:0:102::2 Serial1/2 [up/up] FE80::212:80FF:FE14:4D00 --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 10 /0.1 R2(config-subif)#ipv add fe80::2 li R2(config-subif)#ipv add fe80::2 link-local R2(config-subif)#^Z R2# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7(config-subif)#ipv add 2005:0:702::7/64nt s 1/0.2 pv add 2005:0:702::7/64nt s 1/0.2  1 R7(config-subif)#ipc  v    v add R7(config-subif)#ipv address fe80::7 li R7(config-subif)#^x3 ^ % Invalid input detected at '^' marker. R7(config-subif)# R7(config-subif)# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh ipv int brieipv add fe80::3 link-local do p 2005:0:237::7 2fram map ipv 2005:0:237::2 302 broadcast do p 2005:0:237::2 7ipv add fe80::3 link-local do sh ipv int brie  do sh ipv int brieipv add fe80::3 link-local do p 2005:0:237::7 2fram map ipv 2005:0:237::2 302 broadcast do p 2005:0:237::2 7ipv add fe80::3 link-local do sh ipv int brie  fram map ipb v fe80::2 302 br R3(config-if)#fram map ipv fe80::2 302 br302 br 7 br 307 br 7 307 br R3(config-if)#^Z R3#pin *Mar 1 20:56:19.947: %SYS-5-CONFIG_I: Configured from console by console R3#pin fe80::2 Output Interface: serial 1/0 % Bad interface R3#serial 1/0pin fe80::2\ ^ % Invalid input detected at '^' marker. R3#pin fe80::2\  Output Interface: pin fe80::2\serial 1/0 1/0  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R3#ping 2005:0:1203::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms R3#ping 2005:0:1203::2serial1/0 pin fe80::2 7 Output Interface: pin fe80::7g 2005:0:1203::2serial1/0  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] * R2#ping 2005:0:702::2 7 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R2#ping 2005:0:702::7config t sh ipv int brieconfig t ping 2005:0:702::7 2005:0:702::7 1::1 ::1 ::1 1::10::12::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms R2# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)#^Z R1#sh run *Mar 1 20:59:09.830: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Ethernet0/0 ip address 180.40.7.66 255.255.255.224 half-duplex ! interface Serial0/0 no ip address shutdown --More--  ! interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::1/64 ! interface Serial0/1 no ip address ipv6 address 2005:0:102::1/64 clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! no ip http server ip classless ! ! ! ! ! --More--   R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address --More--   shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::2/64 ipv6 address FE80::2 link-local frame-relay interface-dlci 203 ! --More--  interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::2/64 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address --More--   R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#sh run \ b     | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 no ip address --More--   ipv6 address 2000:3:3::3/64 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local frame-relay map ipv6 FE80::2 302 broadcast --More--   frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::3/64 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown --More--   R3# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 no ip address ipv6 address 2000:4:4::4/64 ! interface FastEthernet0/0 --More--   no ip address duplex auto speed auto ipv6 address 2005:0:104::4/64 ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 broadcast ! ! no ip http server no ip http secure-server ip classless ! ! ! ! ! ! ! --More--   R4# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7(config-subif)#^Z R7#sh run *Mar 1 21:00:27.088: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address --More--   shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.1 255.255.255.224 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80::7 link-local frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point --More--   ipv6 address 2005:0:702::7/64 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! --More--   R7# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#confi gt ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo 0 R4(config-if)#ipov  v rip R4(config-if)#ipv rip ? WORD User selected string identifying this RIP process R4(config-if)#ipv rip R4Rip ? default-information Configure handling of default route enable Enable/disable RIP routing metric-offset Adjust default metric increment summary-address Configure address summarization R4(config-if)#ipv rip R4Rip en R4(config-if)#int fa 0/0 R4(config-if)#int fa 0/0pv rip R4Rip en R4(config-if)#^Z R4# *Mar 1 21:04:15.390: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4#sh run Building configuration... Current configuration : 863 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R4 ! boot-start-marker boot-end-marker ! ! no aaa new-model ip subnet-zero ! ! ip cef no ip domain lookup ! ip audit po max-events 100 ipv6 unicast-routing --More--  ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 no ip address ipv6 address 2000:4:4::4/64 ipv6 rip R4Rip enable ! interface FastEthernet0/0 --More--   no ip address duplex auto speed auto ipv6 address 2005:0:104::4/64 ipv6 rip R4Rip enable ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 broadcast ! ! no ip http server no ip http secure-server ip classless ! ! ipv6 router rip R4Rip ! ! ! --More--  ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R4#^x1 % Unknown command or computer name, or unable to find computer address R4# R4# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ipv rip R1Rip en R1(config-if)#int s 1/0 ^ % Invalid input detected at '^' marker. R1(config)#int s 1/0   0/1 R1(config-if)#int s 0/11/0pv rip R1Rip en R1(config-if)#^Z R1#^Z R1# *Mar 1 21:03:22.881: %SYS-5-CONFIG_I: Configured from console by console R1#^x2 % Unknown command or computer name, or unable to find computer address R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/1 R2(config-if)#ipv rip R2Rip en R2(config-if)#^Z R2#sh ip *Mar 1 21:02:45.984: %SYS-5-CONFIG_I: Configured from console by console R2#sh ipv route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::202:FDFF:FE79:C2A0, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::202:FDFF:FE79:C2A0, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#ping 2000:4:4::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/36/48 ms R2# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b 0/1 interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::1/64 ipv6 rip R1Rip enable ! interface Serial0/1 no ip address ipv6 address 2005:0:102::1/64 ipv6 rip R1Rip enable clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! no ip http server ip classless ! ! ipv6 router rip R1Rip ! --More--   R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b     int s 1/1 Building configuration... Current configuration : 96 bytes ! interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ipv6 rip R2Rip enable end R2# R2# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b Lo interface Loopback0 no ip address ipv6 address 2000:4:4::4/64 ipv6 rip R4Rip enable ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2005:0:104::4/64 ipv6 rip R4Rip enable ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 broadcast ! ! no ip http server no ip http secure-server ip classless --More--   R4# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv acc R1(config)#ipv access-list ? WORD User selected string identifying this access list log-update Control access list log updates R1(config)#ipv access-list Prob3 ? R1(config)#ipv access-list Prob3 R1(config-ipv6-acl)#? IPv6 Access List configuration commands: default Set a command to its defaults deny Specify packets to reject evaluate Evaluate an access list exit Exit from access-list configuration mode no Negate a command or set its defaults permit Specify packets to forward remark Access list entry comment sequence Sequence number for this entry R1(config-ipv6-acl)#den 2000:4:4:: :/64 ? X:X:X:X::X/<0-128> IPv6 destination prefix x:x::y/ any Any destination prefix host A single destination host R1(config-ipv6-acl)#den 2000:4:4::/64  \                  exit R1(config)#exitipv access-list Prob3 nipv access-list Prob3 oipv access-list Prob3  ipv access-list Prob3  % Access list not found R1(config)#ipv router rip R1Rip R1(config-rtr)#distr R1(config-rtr)#distribute-list ? prefix-list Filter connections based on an IPv6 prefix-list R1(config-rtr)#distribute-list                 exit R1(config)#ipv   R1(config)#ipv6 pr R1(config)#ipv6 prefix-list ? WORD Name of a prefix list sequence-number Include/exclude sequence numbers in NVGEN R1(config)#ipv6 prefix-list Prob3 ? deny Specify packets to reject description Prefix-list specific description permit Specify packets to forward seq sequence number of an entry R1(config)#ipv6 prefix-list Prob3 deny 2000:4:4::/64 R1(config)#ipv6 prefix-list Prob3 deny 2000:4:4::/64                  per any ^ % Invalid input detected at '^' marker. R1(config)#ipv6 prefix-list Prob3 per any   ::/0 le 132 ^ % Invalid input detected at '^' marker. R1(config)#ipv6 prefix-list Prob3 per ::/0 le 132  28 R1(config)#ipv6 prefix-list Prob3 per ::/0 le 12832any deny 2000:4:4::/64exit ipv router rip R1Rip R1(config-rtr)#dirst   str R1(config-rtr)#distribute-list p R1(config-rtr)#distribute-list prefix-list ? WORD Prefix-list name R1(config-rtr)#distribute-list prefix-list Prob3 ? in out R1(config-rtr)#distribute-list prefix-list Prob3 out ser`  R1(config-rtr)#distribute-list prefix-list Prob3 out serial 0/1 R1(config-rtr)#^Z R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#sh ipv route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::202:FDFF:FE79:C2A0, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::202:FDFF:FE79:C2A0, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#clea ipb v route * R2#clea ipv route *sh ipv route  IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::202:FDFF:FE79:C2A0, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::202:FDFF:FE79:C2A0, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   R2#sh ipv riop    p daa ta RIP process "R2Rip", local RIB 2000:4:4::/64, metric 3, installed Serial1/1/FE80::202:FDFF:FE79:C2A0, expires in 138 secs 2005:0:102::/64, metric 2 Serial1/1/FE80::202:FDFF:FE79:C2A0, expires in 165 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::202:FDFF:FE79:C2A0, expires in 165 secs R2#clea ipv riup  p data * ^ % Invalid input detected at '^' marker. R2#clea ipv rip data *  % No such RIPv6 instance R2#clea ipv rip data      R2Rip ? R2#clea ipv rip R2Rip R2#clea ipv rip R2Rip data *sh ipv rip data  RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB R2#sh ipv rip data RIP process "R2Rip", local RIB 2005:0:102::/64, metric 2 Serial1/1/FE80::202:FDFF:FE79:C2A0, expires in 179 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::202:FDFF:FE79:C2A0, expires in 179 secs R2# R2# R2# R2# R2#sh ipv route IPv6 Routing Table - 11 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::202:FDFF:FE79:C2A0, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] --More--   via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#p 2005:0:104::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/32 ms R2#p 2000:4:4::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::4, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R2#cofnfi =      ^x2 1    RACK12AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#distribute-list prefix-list Prob3 out serial 0/1ipv router rip R1Rip 6 prefix-list Prob3 per ::/0 le 12832283228      ge ? <0-128> Minimum prefix length R1(config)#ipv6 prefix-list Prob3 per ::/0 ge 0 R1(config)#do sh run | ipv     pref sh run | pref ^ % Invalid input detected at '^' marker. R1(config)#do sh run | prefbpref sh run | bpref ^ % Invalid input detected at '^' marker. R1(config)#do sh run | bpref pref distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ipv6 prefix-list Prob3 seq 15 permit ::/0 ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1(config)#do sh run | b prefpref pref ipv6 prefix-list Prob3 per ::/0 ge 0Prob3 sper ::/0 ge 0eper ::/0 ge 0qper ::/0 ge 0 per ::/0 ge 01per ::/0 ge 05per ::/0 ge 0 per ::/0 ge 0nipv6 prefix-list Prob3 seq 15 per ::/0 ge 0oipv6 prefix-list Prob3 seq 15 per ::/0 ge 0 ipv6 prefix-list Prob3 seq 15 per ::/0 ge 0 R1(config)#no ipv6 prefix-list Prob3 seq 15 per ::/0 ge 0do sh run | b pref  distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1(config)#^Z R1#s *Mar 1 21:12:38.348: %SYS-5-CONFIG_I: Configured from console by console R1#sh ru  ~ n | b rotuer    uter router rip version 2 network 180.40.0.0 no auto-summary ! no ip http server ip classless ! ! ipv6 router rip R1Rip distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ! ! ! ! ! line con 0 exec-timeout 0 0 --More--   R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2# R2#cofn   onfig t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/2 R2(config-if)#ipv ospf ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R2(config-if)#ipv ospf 1 ? area Set the OSPF area ID R2(config-if)#ipv ospf 1 area ? <0-4294967295> OSPF area ID as a decimal value A.B.C.D OSPF area ID in IP address format R2(config-if)#ipv ospf 1 area 20 ? instance Set the OSPF instance R2(config-if)#ipv ospf 1 area 20 R2(config-if)# *Mar 1 21:12:45.811: %OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id, please configure manually R2(config-if)#rou   ipv router ospf 1 R2(config-rtr)#route R2(config-rtr)#router-id 2.2.2.2 R2(config-rtr)#do sh run int s 1/2 Building configuration... Current configuration : 113 bytes ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 ospf 1 area 20 clock rate 64000 end R2(config-rtr)# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#confi gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ipv router ospf 1 R3(config-rtr)# *Mar 1 21:13:27.023: %OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id, please configure manually R3(config-rtr)#rou R3(config-rtr)#router-id 3.3.3.3 R3(config-rtr)#int s 1/2 R3(config-if)#ipv ospf 1 area 20 R3(config-if)#int lo 0 R3(config-if)#int lo 0pv ospf 1 area 20  51 R3(config-if)# *Mar 1 21:13:54.584: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/2 from LOADING to FULL, Loading Done R3(config-if)#do sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:37 11 Serial1/2 R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Mar R2(config-rtr)#do sh ipv route IPv6 Routing Table - 11 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::202:FDFF:FE79:C2A0, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] --More--   via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2(config-rtr)#area 20 ? default-cost Set the summary default-cost of a NSSA/stub area nssa Specify a NSSA area range Summarize routes matching address/mask (border routers only) stub Specify a stub area virtual-link Define a virtual link and its parameters R2(config-rtr)#area 20 vi R2(config-rtr)#area 20 virtual-link ? A.B.C.D RouterID associated with virtual link neighbor R2(config-rtr)#area 20 virtual-link 3.3.3.3 ? dead-interval Dead router detection time hello-interval Hello packet interval retransmit-interval LSA retransmit interval transmit-delay LSA transmission delay R2(config-rtr)#area 20 virtual-link 3.3.3.3 R2(config-rtr)# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#ipv router ospf 1 R3(config-rtr)#area 20 vir R3(config-rtr)#area 20 virtual-link 2.2.2.2 R3(config-rtr)#^Z R3# *Mar 1 21:15:20.028: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 21:15:24.471: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on OSPF_VL0 from LOADING to FULL, Loading Done R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 21:15 R2(config-rtr)#^Z R2# *Mar 1 21:15:45.370: %SYS-5-CONFIG_I: Configured from console by console R2#sh ipv route IPv6 Routing Table - 13 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::3/128 [110/781] via FE80::212:80FF:FE14:1A00, Serial1/2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::202:FDFF:FE79:C2A0, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] via ::, Serial1/2 O 2005:0:1203::3/128 [110/781] via FE80::212:80FF:FE14:1A00, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#sh ipv ospf data OSPFv3 Router with ID (2.2.2.2) (Process ID 1) Router Link States (Area 0) ADV Router Age Seq# Fragment ID Link count Bits 2.2.2.2 46 0x80000003 0 1 B 3.3.3.3 5 (DNA) 0x80000002 0 1 B Inter Area Prefix Link States (Area 0) ADV Router Age Seq# Prefix 2.2.2.2 52 0x80000001 2005:0:1203::/64 2.2.2.2 52 0x80000001 2005:0:1203::2/128 2.2.2.2 52 0x80000001 2005:0:1203::3/128 3.3.3.3 11 (DNA) 0x80000001 2005:0:1203::/64 3.3.3.3 11 (DNA) 0x80000001 2005:0:1203::2/128 3.3.3.3 11 (DNA) 0x80000001 2000:3:3::3/128 3.3.3.3 1 (DNA) 0x80000001 2005:0:1203::3/128 Link (Type-8) Link States (Area 0) ADV Router Age Seq# Link ID Interface --More--   R2#ping 2000:3:3::34 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::34, timeout is 2 seconds: .. Success rate is 0 percent (0/2) R2#[Aping 2000:3:3::34  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms R2#sh ru  n | b 1/2 interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 ospf 1 area 20 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 --More--   no ip address shutdown ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes area 20 virtual-link 3.3.3.3 ! ipv6 router rip R2Rip ! ! ! ! ! ! ! ! ! --More--   R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b Lo interface Loopback0 no ip address ipv6 address 2000:3:3::3/64 ipv6 ospf 1 area 51 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay --More--   ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local frame-relay map ipv6 FE80::2 302 broadcast frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::3/64 ipv6 ospf 1 area 20 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown --More--  ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 3.3.3.3 log-adjacency-changes area 20 virtual-link 2.2.2.2 ! --More--   R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#config Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. R2(config)#r ipv rotuer      uter ospf 1 R2(config-rtr)#red R2(config-rtr)#redistribute rip ? WORD User selected string identifying this process R2(config-rtr)#redistribute rip R2Rip ? metric Metric for redistributed routes metric-type OSPF/IS-IS exterior metric type for redistributed routes route-map Route map reference tag Set tag for routes redistributed into OSPF R2(config-rtr)#redistribute rip R2Rip tag ? <0-4294967295> 32-bit tag value R2(config-rtr)#redistribute rip R2Rip tag 2 ? metric Metric for redistributed routes metric-type OSPF/IS-IS exterior metric type for redistributed routes route-map Route map reference R2(config-rtr)#redistribute rip R2Rip tag 2 R2(config-rtr)#ipv rotuer      uter rip R2Rip R2(config-rtr)#redis R2(config-rtr)#redistribute ospf 1 ? match Redistribution of OSPF routes metric Metric for redistributed routes route-map Route map reference R2(config-rtr)#redistribute ospf 1                     def R2(config-rtr)#default ? distance Administrative distance distribute-list Filter networks in routing updates maximum-paths Forward packets over multiple paths poison-reverse Poison reverse updates port Port and multicast address redistribute Redistribute IPv6 prefixes from another routing protocol split-horizon Split horizon updates summary-prefix Configure IPv6 summary prefix timers Adjust routing timers R2(config-rtr)#default         red R2(config-rtr)#redistribute ospf 1 me R2(config-rtr)#redistribute ospf 1 metric ? <0-16> Default metric transparent Transparently redistribute metric R2(config-rtr)#redistribute ospf 1 metric  2 ? match Redistribution of OSPF routes route-map Route map reference R2(config-rtr)#redistribute ospf 1 metric 2 R2(config-rtr)# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#shg    ip  v route IPv6 Routing Table - 9 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::3/128 [120/4] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::4/128 [0/0] via ::, Loopback0 R 2005:0:102::/64 [120/2] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:1203::3/128 [120/4] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] --More--   R4#p 2000:3:3::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/68/80 ms R4#2000:3:3::3 Trying 2000:3:3::3 ... Open R3#q [Connection to 2000:3:3::3 closed by foreign host] R4# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#sh ipv rotue ^ % Invalid input detected at '^' marker. R3#sh ipv rotueue ute IPv6 Routing Table - 10 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3::3/128 [0/0] via ::, Loopback0 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/2 C 2005:0:237::/64 [0/0] via ::, Serial1/0 L 2005:0:237::3/128 [0/0] via ::, Serial1/0 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/2 L 2005:0:1203::3/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] --More--   via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2(config-rtr)#red R2(config-rtr)#redistribute co R2(config-rtr)#redistribute connected R2(config-rtr)#redistribute connected ospf 1 metric 2 ipv router rip R2Rip redistribute rip R2Rip tag 2 ipv router ospf 1 area 20 virtual-link 3.3.3.3 ipv router ospf 1 area 20 virtual-link 3.3.3.3 do sh ipv route run int s 1/2ipv route area 20 virtual-link 3.3.3.3 ipv router ospf 1  R2(config-rtr)#ipv router ospf 1redistribute connected R2(config-rtr)#^Z R2# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#2000:3:3::3p 2000:3:3::3sh ipv route  IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::3/128 [120/4] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::4/128 [0/0] via ::, Loopback0 R 2005:0:102::/64 [120/2] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:237::/64 [120/3] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 R 2005:0:702::/64 [120/3] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 R 2005:0:1203::/64 [120/3] --More--   via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 R 2005:0:1203::3/128 [120/4] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R4# RACK12AS>2 3 [Resuming connection 3 to r3 ... ] R3#sh ipv route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3::3/128 [0/0] via ::, Loopback0 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/2 C 2005:0:237::/64 [0/0] via ::, Serial1/0 L 2005:0:237::3/128 [0/0] via ::, Serial1/0 OE2 2005:0:702::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203::2/128 [110/781] --More--   via FE80::212:80FF:FE14:4D00, Serial1/2 L 2005:0:1203::3/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] * R2#sh run | b rotuer R2#sh run | b router ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes area 20 virtual-link 3.3.3.3 redistribute connected redistribute rip R2Rip tag 2 ! ipv6 router rip R2Rip redistribute connected redistribute ospf 1 metric 2 ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous --More--   R2#confi gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s 1/0.1 R2(config-subif)#ipv ospf 1 area 0 R2(config-subif)#ipv ospf 1 area 0nt s 1/0.1  2 R2(config-subif)#int s 1/0.2pv ospf 1 area 0 R2(config-subif)#^Z R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ipv ospf 1 area -0  0 R3(config-if)#^Z R3# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0.1 R7(config-subif)#ipv ospf 1 area               ipv router ospf 1 R7(config-rtr)#rou R7(config-rtr)#router-id 7.7.7.7 R7(config-rtr)#int s 1/0.1 R7(config-subif)#ipv ospf 1 area 0 R7(config-subif)#ipv ospf 1 area 0nt s 1/0.1  2 R7(config-subif)#int s 1/0.2pv ospf 1 area 0 R7(config-subif)#^Z R7# *Mar 1 21:27:37.713: %SYS-5-CONFIG_I: Configured from console by console R7#sh ipv ospf nei R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:39 28 Serial1/0.2 R7# *Mar 1 21:27:46.063: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0.2 from LOADING to FULL, Loading Done R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:38 28 Serial1/0.2 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:37 28 Serial1/0.2 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:39 28 Serial1/0.2 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:39 28 Serial1/0.2 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:39 28 Serial1/0.2 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:38 28 Serial1/0.2 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:38 28 Serial1/0.2 R7#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 2.2.2.2 1 FULL/ - 00:00:38 28 Serial1/0.2 R7# RACK12AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#do sh run int s 1/09 sh run int s 1/09 ^ % Invalid input detected at '^' marker. R3(config-if)#do sh run int s 1/09  Building configuration... Current configuration : 341 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local ipv6 ospf 1 area 0 frame-relay map ipv6 FE80::2 302 broadcast frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast end R3(config-if)#no frame-relay map ipv6 FE80::7 307 broadcast R3(config-if)#do sh ip  v os fint      p  pt f int s 1/0 Serial1/0 is up, line protocol is up Link Local Address FE80::3, Interface ID 9 Area 0, Process ID 1, Instance ID 0, Router ID 3.3.3.3 Network Type NON_BROADCAST, Cost: 781 Transmit Delay is 1 sec, State WAITING, Priority 1 No designated router on this network No backup designated router on this network Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 Hello due in 00:00:27 Wait time before Designated router selection 00:00:27 Index 1/2/4, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) R3(config-if)#^x1 ^ % Invalid input detected at '^' marker. R3(config-if)# R3(config-if)# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh ipv os int s 1/0.2 Serial1/0.2 is up, line protocol is up Link Local Address FE80::212:80FF:FE14:4D00, Interface ID 28 Area 0, Process ID 1, Instance ID 0, Router ID 2.2.2.2 Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:00 Index 1/3/4, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 7.7.7.7 Suppress hello for 0 neighbor(s) R2#sh ipv os int s 1/0.2 ` ^ % Invalid input detected at '^' marker. R2#sh ipv os int s 1/0.` 1 Serial1/0.1 is up, line protocol is up Link Local Address FE80::2, Interface ID 27 Area 0, Process ID 1, Instance ID 0, Router ID 2.2.2.2 Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:03 Index 1/2/3, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) R2#^x   RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#ipv ospf ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R3(config-if)#ipv ospf net R3(config-if)#ipv ospf network po R3(config-if)#ipv ospf network point-to-m R3(config-if)#ipv ospf network point-to-multipoint R3(config-if)#ipv ospf h R3(config-if)#ipv ospf hello-interval 10 R3(config-if)#doi    sh *Mar 1 21:30:15.624: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from LOADING to FULL, Loading Done R3(config-if)#do sh ipv os f  pf nei Neighbor ID Pri State Dead Time Interface ID Interface 7.7.7.7 1 EXCHANGE/ - 00:00:38 27 Serial1/0 2.2.2.2 1 FULL/ - 00:00:38 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:31 11 Serial1/2 R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#do dse  eb fram map deb fram map ^ % Invalid input detected at '^' marker. R3(config-if)#do deb fram map   pack Frame Relay packet debugging is on R3(config-if)# *Mar 1 21:31:27.410: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3(config-if)#do u al *Mar 1 21:31:28.596: Serial1/0(i): dlci 302(0x48E1), pkt type 0x86DD, datagramsize 84l R3(config-if)#do u all *Mar 1 21:31:30.126: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 72 *Mar 1 21:31:30.126: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3(config-if)#do u all *Mar 1 21:31:31.232: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 84 *Mar 1 21:31:32.222: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3(config-if)#do u all *Mar 1 21:31:35.010: Serial1/0: broadcast search *Mar 1 21:31:35.010: Serial1/0: Broadcast on DLCI 302 link 79 *Mar 1 21:31:35.010: Serial1/0(o): dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:35.010: Serial1/0: Broadcast on DLCI 307 link 79 *Mar 1 21:31:35.010: Serial1/0(o): dlci 307(0x4C31), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:35.010: Serial1/0(o): dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:35.063: broadcast dequeue *Mar 1 21:31:35.063: Serial1/0(o):Pkt sent on dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:35.063: broadcast dequeue R3(config-if)#do u all *Mar 1 21:31:35.063: Serial1/0(o):Pkt sent on dlci 307(0x4C31), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:35.063: broadcast dequeue *Mar 1 21:31:35.063: Serial1/0(o):Pkt sent on dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:35.135: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 72 *Mar 1 21:31:35.135: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3(config-if)#do u all *Mar 1 21:31:36.765: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3(config-if)#do u all *Mar 1 21:31:38.612: Serial1/0(i): dlci 302(0x48E1), pkt type 0x86DD, datagramsize 84 R3(config-if)#do u all *Mar 1 21:31:40.143: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 72 *Mar 1 21:31:40.143: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3(config-if)#do u all *Mar 1 21:31:41.249: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 84 *Mar 1 21:31:41.345: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3(config-if)#do u all All possible debugging has been turned off R3(config-if)# *Mar 1 21:31:45.011: Serial1/0: broadcast search *Mar 1 21:31:45.011: Serial1/0: Broadcast on DLCI 302 link 79 *Mar 1 21:31:45.011: Serial1/0(o): dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:45.011: Serial1/0: Broadcast on DLCI 307 link 79 *Mar 1 21:31:45.011: Serial1/0(o): dlci 307(0x4C31), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:45.011: Serial1/0(o): dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:45.079: broadcast dequeue *Mar 1 21:31:45.079: Serial1/0(o):Pkt sent on dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:45.079: broadcast dequeue R3(config-if)# *Mar 1 21:31:45.079: Serial1/0(o):Pkt sent on dlci 307(0x4C31), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:45.079: broadcast dequeue *Mar 1 21:31:45.079: Serial1/0(o):Pkt sent on dlci 302(0x48E1), pkt type 0x86DD(IPV6), datagramsize 88 *Mar 1 21:31:45.151: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 72 *Mar 1 21:31:45.151: Serial1/0:Encaps failed--no map entry link 79(IPV6) R3(config-if)# R3(config-if)# R3(config-if)# R3(config-if)#do u alldeb fram packmap sh ipv ospf neiipv ospf hello-interval 10network point-to-multipoint ^x1 do sh ipv ospf int s 1/0no frame-relay map ipv6 FE80::7 307 broadcastno frame-relay map ipv6 FE80::7 307 broadcast  frame-relay map ipv6 FE80::7 307 broadcast  R3(config-if)#^Z R3# *Mar 1 21:31:57.443: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 21:32:00.656: %OSPFv3-5-ADJCHG: Process 1, Nbr 7.7.7.7 on Serial1/0 from LOADING to FULL, Loading Done R3# R3# R3# R3# R3#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 7.7.7.7 1 FULL/ - 00:00:36 27 Serial1/0 2.2.2.2 1 FULL/ - 00:00:39 27 Serial1/0 2.2.2.2 1 FULL/ - - 29 OSPF_VL0 2.2.2.2 1 FULL/ - 00:00:35 11 Serial1/2 R3# RACK12AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh ipv rotue ^ % Invalid input detected at '^' marker. R7#sh ipv rotue   ute IPv6 Routing Table - 13 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::3/128 [110/781] via FE80::3, Serial1/0.1 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] --More--   via FE80::212:80FF:FE14:4D00, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7# R7#tclsh R7(tcl)#foreach test { +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3::3 +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/88/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/85/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/88/89 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 164/166/169 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms R7# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3# R3#tclsh R3(tcl)#foreach test { +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3::3 +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/74/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/67/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/69/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/40/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/51/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/57/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/74/85 ms R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Mar R2# R2#tclsh R2(tcl)#foreach test { +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3::3 +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/31/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/46/57 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/40/56 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 164/167/169 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R2#^x1    RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#tclsh R1(tcl)#foreach test { +>(tcl)#2000:4:4::4 +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3::3 +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/29 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/67/72 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/70/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/74/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/116/120 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/85/88 ms R1# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#tclsh R4(tcl)#foreach test { +>(tcl)#2000:4:4::4 +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3::3 +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/31/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/69/80 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 76/79/84 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/77/80 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/119/124 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/89/92 ms R4#^x2 % Unknown command or computer name, or unable to find computer address R4# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | 1/0   b 1/0.1 interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::2/64 ipv6 ospf 1 area 0 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ipv6 rip R2Rip enable ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 ospf 1 area 20 clock rate 64000 ! interface Serial1/3 --More--   R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b     int s 1/0 Building configuration... Current configuration : 409 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local ipv6 ospf network point-to-multipoint ipv6 ospf hello-interval 10 ipv6 ospf 1 area 0 frame-relay map ipv6 FE80::2 302 broadcast frame-relay map ipv6 FE80::7 307 broadcast frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast end R3# R3# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#sh ruN | b 1/0 interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80::7 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::7/64 ipv6 ospf 1 area 0 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! --More--   R7#confi g t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int tu 0 R7(config-if)#tun R7(config-if)#tunnel *Mar 1 21:37:27.717: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R7(config-if)#tunnel sou fa -0  0/1 R7(config-if)#tun des 180.40.7.66 R7(config-if)#ke R7(config-if)#keepalive R7(config-if)# *Mar 1 21:37:41.904: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R7(config-if)#ipv add 200 17:17:17::7  /64 R7(config-if)#ipv router       ip R7Rip en R7(config-if)#^Z R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0 R1(config-if)#tun *Mar 1 21:39:27.966: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#tun sou 3 e 0/0 R1(config-if)#tun dest 180.50.7    40.7.1 R1(config-if)#keep R1(config-if)# *Mar 1 21:39:41.496: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-if)#ipv add 200 17:17:17::1  /64 R1(config-if)#ipv rip R1Rip en R1(config-if)#^Z R1# RACK12AS>7 [Resuming connection 7 to r7 ... ] * R7#sh ipv route IPv6 Routing Table - 15 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::3/128 [110/781] via FE80::3, Serial1/0.1 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] --More--   via FE80::212:80FF:FE14:4D00, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 C 2017:17:17::/64 [0/0] via ::, Tunnel0 L 2017:17:17::7/128 [0/0] via ::, Tunnel0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#ping 2017:17:17::1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2017:17:17::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R7#ping 2017:17:17::1sh ipv route  IPv6 Routing Table - 15 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::3/128 [110/781] via FE80::3, Serial1/0.1 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] --More--   via FE80::212:80FF:FE14:4D00, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 C 2017:17:17::/64 [0/0] via ::, Tunnel0 L 2017:17:17::7/128 [0/0] via ::, Tunnel0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#sh ipv route IPv6 Routing Table - 16 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::3/128 [110/781] via FE80::3, Serial1/0.1 R 2000:4:4::/64 [120/3] via FE80::202:FDFF:FE79:C2A0, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] --More--   via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::212:80FF:FE14:4D00, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 C 2017:17:17::/64 [0/0] via ::, Tunnel0 L 2017:17:17::7/128 [0/0] via ::, Tunnel0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#q p 2000:4:4::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R7#tclsh R7(tcl)#foreach test { +>(tcl)#2000:4:4::4 +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3::3 +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/89/92 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/86/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/94/120 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 164/165/169 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#sh run   int tu 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive set (10 sec), retries 3 Tunnel source 180.40.7.66 (Ethernet0/0), destination 180.40.7.1 Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled Tunnel TTL 255 Checksumming of packets disabled, fast tunneling enabled Last input 00:00:09, output 00:00:07, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 38 packets input, 3364 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 38 packets output, 4084 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R1#q sh run int tu 0 Building configuration... Current configuration : 168 bytes ! interface Tunnel0 no ip address ipv6 address 2017:17:17::1/64 ipv6 rip R1Rip enable keepalive 10 3 tunnel source Ethernet0/0 tunnel destination 180.40.7.1 end R1# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int tu 0 Building configuration... Current configuration : 173 bytes ! interface Tunnel0 no ip address ipv6 address 2017:17:17::7/64 ipv6 rip R7Rip enable keepalive 10 3 tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 end R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int ut  tu 0 R7(config-if)#tun mode ? aurp AURP TunnelTalk AppleTalk encapsulation cayman Cayman TunnelTalk AppleTalk encapsulation dvmrp DVMRP multicast tunnel eon EON compatible CLNS tunnel gre generic route encapsulation protocol ipip IP over IP encapsulation iptalk Apple IPTalk encapsulation ipv6ip IPv6 over IP encapsulation mpls MPLS encapsulations nos IP over IP encapsulation (KA9Q/NOS compatible) R7(config-if)#tun mode ipv R7(config-if)#tun mode ipv6ip R7(config-if)# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0-  R1(config-if)#tun mode ipv6ip R1(config-if)#^Z R1#sh *Mar 1 21:43:36.113: %SYS-5-CONFIG_I: Configured from console by console R1#sh config tsh run int tu 0 Building configuration... Current configuration : 188 bytes ! interface Tunnel0 no ip address ipv6 address 2017:17:17::1/64 ipv6 rip R1Rip enable keepalive 10 3 tunnel source Ethernet0/0 tunnel destination 180.40.7.1 tunnel mode ipv6ip end R1# R1# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7(config-if)#^Z R7#sh r *Mar 1 21:43:00.715: %SYS-5-CONFIG_I: Configured from console by console R7#sh run int tu 0 Building configuration... Current configuration : 193 bytes ! interface Tunnel0 no ip address ipv6 address 2017:17:17::7/64 ipv6 rip R7Rip enable keepalive 10 3 tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 tunnel mode ipv6ip end R7# R7#sh int tun 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive set (10 sec), retries 3 Tunnel source 180.40.7.1 (FastEthernet0/1), destination 180.40.7.66 Tunnel protocol/transport IPv6/IP, key disabled, sequencing disabled Tunnel TTL 255 Checksumming of packets disabled, fast tunneling enabled Last input 00:00:24, output 00:00:08, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 50 packets input, 5660 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 65 packets output, 5212 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R7#confi gt  t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int lo 1 R7(config-if)#ipv add 2006:7:6 7::/128 R7(config-if)#^Z R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int lo 1 R1(config-if)#ipv add 2006:1:1::/128 R1(config-if)#^Z R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipv pred  R2(config)#ipv prefix-list ? WORD Name of a prefix list sequence-number Include/exclude sequence numbers in NVGEN R2(config)#ipv prefix-list NoLoop den 2006:2:2::/128 R2(config)#ipv prefix-list NoLoop den 2006:2:2::/128                    per ::/0 le 128 R2(config)#int lo 1 R2(config-if)#ipv router ospf 1 R2(config-rtr)#redis R2(config-rtr)#redistribute              distr R2(config-rtr)#distribute-list p R2(config-rtr)#distribute-list prefix-list NoLoop ? in out R2(config-rtr)#distribute-list prefix-list NoLoop out con R2(config-rtr)#distribute-list prefix-list NoLoop out connected ? R2(config-rtr)#distribute-list prefix-list NoLoop out connected R2(config-rtr)#ipv rotuer      uter rip R2Rip R2(config-rtr)#ipv router rip R2Ripdistribute-list prefix-list NoLoop out connected ^ % Invalid input detected at '^' marker. R2(config-rtr)#distribute-list prefix-list NoLoop out connected           ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config-rtr)#distribute-list prefix-list NoLoop out R2(config-rtr)#distribute-list prefix-list NoLoop out ndistribute-list prefix-list NoLoop out odistribute-list prefix-list NoLoop out  distribute-list prefix-list NoLoop out  R2(config-rtr)#exit R2(config)#route-map NoLoop R2(config-route-map)#match ipv pr R2(config-route-map)#match ipv pre R2(config-route-map)#match ipv pre? % Unrecognized command R2(config-route-map)#match ipv pre       ? as-path Match BGP AS path list clns CLNS information community Match BGP community list extcommunity Match BGP/VPN extended community list interface Match first hop interface of route ip IP specific information ipv6 IPv6 specific information length Packet length metric Match metric of route mpls-label Match routes which have MPLS labels nlri BGP NLRI type policy-list Match IP policy list route-type Match route-type of route tag Match tag of route R2(config-route-map)#match ipv ? address Match address of route next-hop Match next-hop address of route route-source Match advertising source address of route R2(config-route-map)#match ipv add ? WORD IPv6 access-list name prefix-list IPv6 prefix-list R2(config-route-map)#match ipv add pr R2(config-route-map)#match ipv add prefix-list NoLop op R2(config-route-map)#ipv router rip R2Rip R2(config-rtr)#do sh run | b router ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes area 20 virtual-link 3.3.3.3 distribute-list prefix-list NoLoop out connected redistribute connected redistribute rip R2Rip tag 2 ! ipv6 router rip R2Rip redistribute connected redistribute ospf 1 metric 2 ! ! ! ipv6 prefix-list NoLoop seq 5 deny 2006:2:2::/128 ipv6 prefix-list NoLoop seq 10 permit ::/0 le 128 route-map NoLoop permit 10 match ipv6 address prefix-list NoLoop ! ! ! ! ! --More--  ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R2(config-rtr)#redistribute connected rou R2(config-rtr)#redistribute connected route-map ? WORD Pointer to route-map entries R2(config-rtr)#redistribute connected route-map NoLoop ? metric Metric for redistributed routes R2(config-rtr)#redistribute connected route-map NoLoop R2(config-rtr)#^Z R2# *Mar 1 21:50:04.970: %SYS-5-CONFIG_I: Configured from console by console R2#co  config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int lo 1 R2(config-if)#ipv add 2006:3 2:2::/128 R2(config-if)#^Z R2#^x *Mar 1 21:50:20.632: %SYS-5-CONFIG_I: Configured from console by console R2#^x3 % Unknown command or computer name, or unable to find computer address R2# R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int lo 1 R3(config-if)#ipv add 2006:3:3::/128 R3(config-if)#^Z R3# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#confifg t ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo 1 R4(config-if)#ipv add 2006:4:45::   ::/128 R4(config-if)#^Z R4# *Mar 1 21:53:24.806: %SYS-5-CO RACK12AS>1 [Resuming connection 1 to r1 ... ] * R1#shb run int run int  run int lo1 Building configuration... Current configuration : 71 bytes ! interface Loopback1 no ip address ipv6 address 2006:1:1::/128 end R1# RACK12AS>3 [Resuming connection 3 to r3 ... ] *M R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b Lo interface Loopback1 no ip address ipv6 address 2006:2:2::/128 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay --More--  ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::2/64 ipv6 ospf 1 area 0 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ipv6 rip R2Rip enable ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 ospf 1 area 20 clock rate 64000 ! --More--  interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! ip classless ! no ip http server --More--  no ip http secure-server ! ipv6 router ospf 1 router-id 2.2.2.2 log-adjacency-changes area 20 virtual-link 3.3.3.3 distribute-list prefix-list NoLoop out connected redistribute connected redistribute rip R2Rip tag 2 ! ipv6 router rip R2Rip redistribute connected route-map NoLoop redistribute ospf 1 metric 2 ! ! ! ipv6 prefix-list NoLoop seq 5 deny 2006:2:2::/128 ipv6 prefix-list NoLoop seq 10 permit ::/0 le 128 route-map NoLoop permit 10 match ipv6 address prefix-list NoLoop ! ! ! --More--   R2#config t5 ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#rotuer    t ~uter       uter bgp 100 R2(config-router)#ipv add R2(config-router)#ipv add       add R2(config-router)#address-family ipv6 R2(config-router-af)#nei 2000:3:3::4 3 remote 100 R2(config-router-af)#remote        nee i 2005:0:102::1 remote 200 R2(config-router-af)#net 2006:2:23 ::/128 R2(config-router-af)#nei t 2006:2:2::/128i 2005:0:102::1 remote 2000:3:3::3 remote 100           con R2(config-router-af)#nei 2000:3:3::3 conn R2(config-router-af)#nei 2000:3:3::3 conn? % Unrecognized command R2(config-router-af)#nei 2000:3:3::3 conn                    address-family ipv6router bgp 100 ipv add 2006:2:2::/128nt lo 1 redistribute connected route-map NoLoop int lo 1 pv add 2006:2:2::/128router bgp 100 address-family ipv6nei 2000:3:3::3 remote 1005:0:102::1 remote 200t 2006:2:2::/128  net 2006:2:2::/128 net 2006:2:2::/128i 2005:0:102::1 remote 2000:3:3::3 remote 100           up R2(config-router-af)#nei 2000:3:3::3 update-source s 1/1 R2(config-router-af)#^Z R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#router bgp RACK12AS> [Resuming connection 3 to r3 ... ] 100 R3(config-router)# RACK12AS>2 [Resuming connection 2 to r2 ... ] * R2#sh run | b bgp router bgp 100 no synchronization bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 neighbor 2000:3:3::3 update-source Serial1/1 no neighbor 2000:3:3::3 activate neighbor 2005:0:102::1 remote-as 200 no neighbor 2005:0:102::1 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2005:0:102::1 activate network 2006:2:2::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 2.2.2.2 --More-- RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config-router)#add ipv6 R3(config-router-af)#nei 2005:0:102::2 remote 100 R3(config-router-af)#nei 2005:0:102::2 remote 100          up R3(config-router-af)#nei 2005:0:102::2 update-source lo 0 R3(config-router-af)#nei 2005:0:237::7 remote 100 R3(config-router-af)#^x   RACK12AS>7 [Resuming connection 7 to r7 ... ] *M R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#router bgp 100 R7(config-router)#add ipv        RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config-router-af)#do sh ip bg    pro Routing Protocol is "bgp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set IGP synchronization is disabled Automatic route summarization is disabled Maximum path: 1 Routing Information Sources: Gateway Distance Last Update Distance: external 20 internal 200 local 200 R3(config-router-af)#do sh ip prov pro IPv6 Routing Protocol is "connected" IPv6 Routing Protocol is "static" IPv6 Routing Protocol is "ospf 1" Interfaces (Area 0): Serial1/0 OSPF_VL0 Interfaces (Area 20): Serial1/2 Interfaces (Area 51): Loopback0 Redistribution: None IPv6 Routing Protocol is "bgp 100" IGP synchronization is disabled Redistribution: None Neighbor(s): Address FiltIn FiltOut Weight RoutemapIn RoutemapOut 2005:0:102::2 2005:0:237::7 R3(config-router-af)#  sh    do sh bgp % BGP cannot run because the router-id is not configured R3(config-router-af)# *Mar 1 22:02:32.167: %BGP-4-NORTRID: BGP could not pick a router-id. Please configure manually. R3(config-router-af)#exit R3(config-router)#bgp rout R3(config-router)#bgp router-id 3.3.3.3 R3(config-router)# RACK12AS>2 [Resuming connection 2 to r2 ... ]   log-adjacency-changes --More--   R2#c o   config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int   rotuer    uter bgp 1 100 R2(config-router)#bgp rout R2(config-router)#bgp router-id 2.2.2.2 R2(config-router)#^Z R2# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7(config-router)#bgp router R7(config-router)#bgp router-id 7.7.7.7 R7(config-router)#add ipv6 R7(config-router-af)#nei 2000:3:3::3 remote 100 R7(config-router-af)# RACK12AS>3 [Resuming connection 3 to r3 ... ] *M R3(config-router)#add ipv  6 R3(config-router-af)#nei 2005:0:237::7 up lo 0 R3(config-router-af)#^Z R3#sh run | *Mar 1 22:03:55.347: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes neighbor 2005:0:102::2 remote-as 100 neighbor 2005:0:102::2 update-source Loopback0 no neighbor 2005:0:102::2 activate neighbor 2005:0:237::7 remote-as 100 neighbor 2005:0:237::7 update-source Loopback0 no neighbor 2005:0:237::7 activate no auto-summary ! address-family ipv6 neighbor 2005:0:102::2 activate neighbor 2005:0:237::7 activate exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 --More-- *Mar 1 22:04:05.628: %BGP-5-ADJCHANGE: neighbor 2005:0:237::7 Up --More--   R3# RACK12AS>7 [Resuming connection 7 to r7 ... ] *M R7(config-router-af)#nei 2017:17:17::1 remote 200 R7(config-router-af)# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#rotuer bgp          uter bgp 100   200 R1(config-router)#bgp rotu R1(config-router)#bgp rotu  ut R1(config-router)#bgp router-id 1.1.1.1 R1(config-router)#add ipv6 R1(config-router-af)#nei 1 200 17:17:17::7 remote 100 R1(config-router-af)#nei 2005:0:102::2 remote 100 R1(config-router-af)#net i *Mar 1 22:06:21.884: %BGP-5-ADJCHANGE: neighbor 2017:17:17::7 Up R1(config-router-af)#nei 2005:0:104::4 remote 300 R1(config-router-af)#net 2006:1:1::/128 R1(config-router-af)# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#rotue bgp       uter bgp 100 R3(config-router)#add ipv6 R3(config-router-af)#net 2006:3:3::/128 R3(config-router-af)# RACK12AS>7 [Resuming connection 7 to r7 ... ] *Mar 1 R7(config-router-af)#net 2006:7:7::/128 R7(config-router-af)#^X   RACK12AS>4 [Resuming connection 4 to r4 ... ] IG_I: Configured fr R4#COFIG T ^ % Invalid input detected at '^' marker. R4#configt Translating "configt" Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R4#configt  t  Enter configuration commands, one per line. End with CNTL/Z. R4(config)#rotuer bgp er bgp er bgp uer bgp ter bgp  % Incomplete command. R4(config)#router bgp ~ 300 R4(config-router)#bgp rout R4(config-router)#bgp router-id 4.4.4.4 R4(config-router)#add ipv6 R4(config-router-af)#nei 2005:0:104::1 remote 200 R4(config-router-af)#net 2006:4:4::/128 R4(config-router-af)#^Z R4# RACK12AS>1 [Resuming connection 1 to r1 ... ] * R1(config-router-af)#^Z R1#sh ip   *Mar 1 22:07:53.594: %SYS-5-CONFIG_I: Configured from console by console R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 1, main routing table version 1 4 network entries using 532 bytes of memory 4 path entries using 288 bytes of memory 3 BGP path attribute entries using 180 bytes of memory 1 BGP AS-PATH entries using 24 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1024 total bytes of memory BGP activity 4/0 prefixes, 4/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2005:0:102::2 4 100 7 4 0 0 0 00:01:04 2 2005:0:104::4 4 300 0 0 0 0 0 never Active 2017:17:17::7 4 100 6 4 0 0 0 00:01:34 1 R1# R1# R1# R1#sh bgp BGP table version is 1, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2006:1:1::/128 :: 0 32768 i * 2006:2:2::/128 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2005:0:102::2 0 100 i * 2006:7:7::/128 2017:17:17::7 0 0 100 i R1#sh bgp BGP table version is 1, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2006:1:1::/128 :: 0 32768 i * 2006:2:2::/128 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2017:17:17::7 0 100 i * 2005:0:102::2 0 100 i * 2006:7:7::/128 2017:17:17::7 0 0 100 i R1#sh bgp BGP table version is 1, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2006:1:1::/128 :: 0 32768 i * 2006:2:2::/128 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2017:17:17::7 0 100 i * 2005:0:102::2 0 100 i * 2006:7:7::/128 2017:17:17::7 0 0 100 i R1#sh bgp BGP table version is 5, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 :: 0 32768 i *> 2006:2:2::/128 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2017:17:17::7 0 100 i *> 2005:0:102::2 0 100 i *> 2006:7:7::/128 2017:17:17::7 0 0 100 i R1# *Mar 1 22:08:22.229: %BGP-5-ADJCHANGE: neighbor 2005:0:104::4 Up R1#sh bgp BGP table version is 6, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 :: 0 32768 i *> 2006:2:2::/128 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2017:17:17::7 0 100 i *> 2005:0:102::2 0 100 i *> 2006:4:4::/128 2005:0:104::4 0 0 300 i *> 2006:7:7::/128 2017:17:17::7 0 0 100 i R1#sh bgp sumconfig t sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 6, main routing table version 6 5 network entries using 665 bytes of memory 6 path entries using 432 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1385 total bytes of memory BGP activity 5/0 prefixes, 6/0 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2005:0:102::2 4 100 7 7 5 0 0 00:01:36 2 2005:0:104::4 4 300 5 7 5 0 0 00:00:07 1 2017:17:17::7 4 100 8 9 5 0 0 00:02:07 2 R1#sh bgp sum  BGP table version is 6, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 :: 0 32768 i *> 2006:2:2::/128 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2017:17:17::7 0 100 i *> 2005:0:102::2 0 100 i *> 2006:4:4::/128 2005:0:104::4 0 0 300 i *> 2006:7:7::/128 2017:17:17::7 0 0 100 i R1# RACK12AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh bgp BGP table version is 6, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:104::1 0 0 200 i *> 2006:2:2::/128 2005:0:104::1 0 200 100 i *> 2006:3:3::/128 2005:0:104::1 0 200 100 i *> 2006:4:4::/128 :: 0 32768 i *> 2006:7:7::/128 2005:0:104::1 0 200 100 i R4# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config-router-af)#do sh bgp BGP table version is 7, local router ID is 3.3.3.3 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *>i2006:1:1::/128 2005:0:102::1 0 100 0 200 i * i 2017:17:17::1 0 100 0 200 i *>i2006:2:2::/128 2005:0:102::2 0 100 0 i *> 2006:3:3::/128 :: 0 32768 i *>i2006:4:4::/128 2005:0:102::1 0 100 0 200 300 i *>i2006:7:7::/128 2005:0:237::7 0 100 0 i R3(config-router-af)# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh bgp BGP table version is 5, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102::1 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i *> 2006:4:4::/128 2005:0:102::1 0 200 300 i R2#sh bgp BGP table version is 5, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102::1 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i *> 2006:4:4::/128 2005:0:102::1 0 200 300 i R2# sh bgp BGP table version is 5, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102::1 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i *> 2006:4:4::/128 2005:0:102::1 0 200 300 i R2#sh bgp BGP table version is 5, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102::1 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i *> 2006:4:4::/128 2005:0:102::1 0 200 300 i R2#sh bgp BGP table version is 5, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102::1 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i *> 2006:4:4::/128 2005:0:102::1 0 200 300 i R2#sh bgp sum BGP router identifier 2.2.2.2, local AS number 100 BGP table version is 5, main routing table version 5 4 network entries using 532 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1108 total bytes of memory BGP activity 5/1 prefixes, 5/1 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3::3 4 100 10 12 5 0 0 00:05:22 1 2005:0:102::1 4 200 9 8 5 0 0 00:02:48 2 R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config-router-af)#nei 2005:0:237::7 rout R3(config-router-af)#nei 2005:0:237::7 route-r R3(config-router-af)#nei 2005:0:237::7 route-reflector-client R3(config-router-af)# *Mar 1 22:09:41.479: %BGP-5-ADJCHANGE: neighbor 2005:0:237::7 Down RR client config change R3(config-router-af)#do sh run | bg  b bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes neighbor 2005:0:102::2 remote-as 100 neighbor 2005:0:102::2 update-source Loopback0 no neighbor 2005:0:102::2 activate neighbor 2005:0:237::7 remote-as 100 neighbor 2005:0:237::7 update-source Loopback0 no neighbor 2005:0:237::7 activate no auto-summary ! address-family ipv6 neighbor 2005:0:102::2 activate neighbor 2005:0:237::7 activate neighbor 2005:0:237::7 route-reflector-client network 2006:3:3::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server --More-- *Mar 1 22:10:08.230: %BGP-5-ADJCHANGE: neighbor 2005:0:237::7 Up --More--   R3(config-router-af)# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#sh bgp sum  sum  BGP table version is 6, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:102::1 0 0 200 i *> 2006:2:2::/128 :: 0 32768 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i *> 2006:4:4::/128 2005:0:102::1 0 200 300 i *>i2006:7:7::/128 2005:0:237::7 0 100 0 i R2# R2# R2# R2# R2# RACK12AS>7 [Resuming connection 7 to r7 ... ] *M R7(config-router-af)#do sh bgp BGP table version is 8, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i2006:1:1::/128 2005:0:102::1 0 100 0 200 i *> 2017:17:17::1 0 0 200 i *>i2006:2:2::/128 2005:0:102::2 0 100 0 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i * i2006:4:4::/128 2005:0:102::1 0 100 0 200 300 i *> 2017:17:17::1 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7(config-router-af)#^Z R7# *Mar 1 22:12:42.600: %SYS-5-CONFIG_I: Configured from console by console R7#tclsh R7(tcl)#foreach test { +>(tcl)#2000:4:4::4 +>(tcl)#2005:0:104::4 +>(tcl)#2005:0:104::1 +>(tcl)#2005:0:102::1 +>(tcl)#2005:0:102::2 +>(tcl)#2005:0:1203::2 +>(tcl)#2005:0:237::2 +>(tcl)#2005:0:702::2 +>(tcl)#2005:0:1203::3 +>(tcl)#2000:3:3::3 +>(tcl)#2005:0:237::3 +>(tcl)#2005:0:237::7 +>(tcl)#2005:0:702::7 +>(tcl)#2006:1:1:: +>(tcl)#2006:2:2:: +>(tcl)#2006:3:3:: +>(tcl)#2006:4:4:: +>(tcl)#2006:7:7:: +>(tcl)#2005:17:17::1 +>(tcl)#2005:17:17::7 +>(tcl)#} {ping $test rep 2};tclquit Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/89/92 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 85/87/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/86/88 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 164/166/169 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/60/72 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/61 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:1:1::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:2:2::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:3:3::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:7:7::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:17:17::1, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:17:17::7, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b bgp router bgp 200 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes neighbor 2005:0:102::2 remote-as 100 no neighbor 2005:0:102::2 activate neighbor 2005:0:104::4 remote-as 300 no neighbor 2005:0:104::4 activate neighbor 2017:17:17::7 remote-as 100 no neighbor 2017:17:17::7 activate no auto-summary ! address-family ipv6 neighbor 2005:0:102::2 activate neighbor 2005:0:104::4 activate neighbor 2017:17:17::7 activate network 2006:1:1::/128 exit-address-family ! no ip http server ip classless ! ! --More--   R1#^x2 % Unknown command or computer name, or unable to find computer address R1# R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#shg run          run | b bgp router bgp 100 no synchronization bgp router-id 2.2.2.2 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 neighbor 2000:3:3::3 update-source Serial1/1 no neighbor 2000:3:3::3 activate neighbor 2005:0:102::1 remote-as 200 no neighbor 2005:0:102::1 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2005:0:102::1 activate network 2006:2:2::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 --More--   R2# R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config-router-af)#^Z R3#sh run | b *Mar 1 22:14:28.076: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b bgp router bgp 100 no synchronization bgp router-id 3.3.3.3 bgp log-neighbor-changes neighbor 2005:0:102::2 remote-as 100 neighbor 2005:0:102::2 update-source Loopback0 no neighbor 2005:0:102::2 activate neighbor 2005:0:237::7 remote-as 100 neighbor 2005:0:237::7 update-source Loopback0 no neighbor 2005:0:237::7 activate no auto-summary ! address-family ipv6 neighbor 2005:0:102::2 activate neighbor 2005:0:237::7 activate neighbor 2005:0:237::7 route-reflector-client network 2006:3:3::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server --More--   R3# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | bv    bgp router bgp 300 no synchronization bgp router-id 4.4.4.4 bgp log-neighbor-changes neighbor 2005:0:104::1 remote-as 200 no neighbor 2005:0:104::1 activate no auto-summary ! address-family ipv6 neighbor 2005:0:104::1 activate network 2006:4:4::/128 exit-address-family ! no ip http server no ip http secure-server ip classless ! ! ipv6 router rip R4Rip ! ! ! ! --More--   R4# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2017:17:17::1 remote-as 200 no neighbor 2017:17:17::1 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2017:17:17::1 activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 7.7.7.7 --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int tu 0 R7(config-if)#shut R7(config-if)# *Mar 1 22:26:22.672: %BGP-5-ADJCHANGE: neighbor 2017:17:17::1 Down Interface flap R7(config-if)# *Mar 1 22:26:23.930: %LINK-5-CHANGED: Interface Tunnel0, changed state to administratively down *Mar 1 22:26:24.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R7(config-if)#do sh run int tu 0 Building configuration... Current configuration : 203 bytes ! interface Tunnel0 no ip address shutdown ipv6 address 2017:17:17::7/64 ipv6 rip R7Rip enable keepalive 10 3 tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 tunnel mode ipv6ip end R7(config-if)#no tunnel destination 180.40.7.66 R7(config-if)#no ipv6 address 2017:17:17::7/64 R7(config-if)#ipv add 2002:b428:701::/64 R7(config-if)#tun mode ip R7(config-if)#tun mode ipv R7(config-if)#tun mode ipv6ip 6 R7(config-if)#tun mode ipv6ip 6to4 R7(config-if)#exit R7(config)#ipv route 2002::/8   16 tun 0 R7(config)# R7(config)# R7(config)# R7(config)#router bgp 100 R7(config-router)#add ip v pv6 R7(config-router-af)#do sh run| b      | b bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2017:17:17::1 remote-as 200 no neighbor 2017:17:17::1 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2017:17:17::1 activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 --More--   R7(config-router-af)#no neighbor 2017:17:17::1 remote-as 200 R7(config-router-af)#no neighbor 2017:17:17::1 remote-as 200do sh run | b bgp  router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2017:17:17::1 remote-as 200 no neighbor 2017:17:17::1 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2017:17:17::1 activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 --More--   R7(config-router-af)#no neighbor 2017:17:17::1 activate R7(config-router-af)#no neighbor 2017:17:17::1 activatedo sh run | b bgp  router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2017:17:17::1 remote-as 200 no neighbor 2017:17:17::1 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 --More--   R7(config-router-af)#do sh run | b bgpno neighbor 2017:17:17::1 activatedo sh run | b bgp no neighbor 2017:17:17::1 remote-as 200do sh run | b bgp no neighbor 2017:17:17::1 activatedo sh run | b bgp  exit R7(config-router)#exitdo sh run | b bgpno neighbor 2017:17:17::1 activatedo sh run | b bgp no neighbor 2017:17:17::1 remote-as 200 R7(config-router)#no neighbor 2017:17:17::1 remote-as 200 do no neighbor 2017:17:17::1 remote-as 200exit do sh run | b bgpno neighbor 2017:17:17::1 activatedo sh run | b bgp  router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! --More--   R7(config-router)#add ipv6 R7(config-router-af)#nei 202 02:b428:742:: remote 200 R7(config-router-af)# RACK12AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#confif t ^ % Invalid input detected at '^' marker. R1#confifg t ^ % Invalid input detected at '^' marker. R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#int tu 0 R1(config-if)#do sh run int tu 0 Building configuration... Current configuration : 188 bytes ! interface Tunnel0 no ip address ipv6 address 2017:17:17::1/64 ipv6 rip R1Rip enable keepalive 10 3 tunnel source Ethernet0/0 tunnel destination 180.40.7.1 tunnel mode ipv6ip end R1(config-if)#no tunnel destination 180.40.7.1 R1(config-if)#no ipv6 address 2017:17:17::1/64 R1(config-if)#no *Mar 1 22:30:58.084: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#no ipv6 rip R1Rip enable R1(config-if)# tunnel mode ipv6ip 6 R1(config-if)#ipv add *Mar 1 22:31:11.958: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-if)#ipv add 2002:b428:742:: % Incomplete command. R1(config-if)#ipv add 2002:b428:742::/64 R1(config-if)#exit R1(config)#ipv route 2002::/16 tu 0 R1(config)#rotuer bgp          uter bgp 200 R1(config-router)#no nei 2017:17:17::7 remote 2 100 R1(config-router)#do sh run | b bgp router bgp 200 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes neighbor 2005:0:102::2 remote-as 100 no neighbor 2005:0:102::2 activate neighbor 2005:0:104::4 remote-as 300 no neighbor 2005:0:104::4 activate no auto-summary ! address-family ipv6 neighbor 2005:0:102::2 activate neighbor 2005:0:104::4 activate network 2006:1:1::/128 exit-address-family ! no ip http server ip classless ! ! ipv6 route 2002::/16 Tunnel0 ipv6 router rip R1Rip distribute-list prefix-list Prob3 out Serial0/1 --More--   R1(config-router)#ap dd ipv6 R1(config-router-af)#a nei 2002:b428:701:: remote 100 R1(config-router-af)# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7(config-router-af)#int tu 0 R7(config-if)#no shut R7(config-if)# *Mar 1 22:31:43.201: %LINK-3-UPDOWN: Interface Tunnel0, changed state to up *Mar 1 22:31:44.203: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R7(config-if)# R7(config-if)# R7(config-if)# R7(config-if)# R7(config-if)#exit R7(config)#exit R7#ping 2002 *Mar 1 22:31:50.341: %SYS-5-CONFIG_I: Configured from console by console R7#ping 2002:b428:742:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:742::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms R7# R7# R7# R7#sh ipb v route IPv6 Routing Table - 21 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::3/128 [110/781] via FE80::3, Serial1/0.1 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] --More--   via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::212:80FF:FE14:4D00, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 B 2006:1:1::/128 [200/0] via 2005:0:102::1 B 2006:2:2::/128 [200/0] via 2005:0:102::2 B 2006:3:3::/128 [200/0] via 2000:3:3::3 B 2006:4:4::/128 [200/0] via 2005:0:102::1 LC 2006:7:7::/128 [0/0] via ::, Loopback1 L FE80::/10 [0/0] --More--   via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#sh bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 10, main routing table version 10 5 network entries using 665 bytes of memory 5 path entries using 360 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 1 BGP rrinfo entries using 24 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1337 total bytes of memory BGP activity 6/1 prefixes, 8/3 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3::3 4 100 40 42 10 0 0 00:22:07 4 2002:B428:742:: 4 200 0 0 0 0 0 never Idle R7#sh bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 10, main routing table version 10 5 network entries using 665 bytes of memory 5 path entries using 360 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 1 BGP rrinfo entries using 24 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1337 total bytes of memory BGP activity 6/1 prefixes, 8/3 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3::3 4 100 40 42 10 0 0 00:22:42 4 2002:B428:742:: 4 200 0 0 0 0 0 never Idle R7#sh bgp sumipv routeping 2002:b428:742::config t ping 2002:b428:742:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:742::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms R7#deb bgp ? dampening BGP dampening events BGP events ipv6 Address family keepalives BGP keepalives nsap Address family updates BGP updates R7#deb bgp BGP debugging is on R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv rotue     ute 2002:b428:          ::/0 2002:b428:   28:742:: R7(config)#^Z R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1(config-router-af)#do sh ipv route IPv6 Routing Table - 21 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::3/128 [120/3] via FE80::212:80FF:FE14:4D00, Serial0/1 R 2000:4:4::/64 [120/2] via FE80::20E:38FF:FEF1:63E0, Ethernet0/1 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:742::/64 [0/0] via ::, Tunnel0 L 2002:B428:742::/128 [0/0] via ::, Tunnel0 C 2005:0:102::/64 [0/0] via ::, Serial0/1 L 2005:0:102::1/128 [0/0] via ::, Serial0/1 C 2005:0:104::/64 [0/0] via ::, Ethernet0/1 L 2005:0:104::1/128 [0/0] --More--   R1(config-router-af)#exit R1(config-router)#eit  xit R1(config)#ipv route ::/0 2002:b428:79 02:: R1(config)#^Z R1#p *Mar 1 22:35:45.134: %SYS-5-CONFIG_I: Configured from console by console R1#ping 2002:b428:702:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:702::, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R1#sh run int tu 0 Building configuration... Current configuration : 158 bytes ! interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:742::/64 keepalive 10 3 tunnel source Ethernet0/0 tunnel mode ipv6ip 6to4 end R1#sh ipv route s % Ambiguous command: "sh ipv route s" R1#sh ipv route stA IPv6 Routing Table - 22 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 S ::/0 [1/0] via 2002:B428:702:: S 2002::/16 [1/0] via ::, Tunnel0 R1#sh ipv route stA sh ipv route stA COFNIGT Translating "COFNIGT" Translating "COFNIGT" Translating "COFNIGT" % Unknown command or computer name, or unable to find computer address R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#intpv route ::/0 2002:b428:702::exit ipv route ::/0 2002:b428:702::nipv route ::/0 2002:b428:702::oipv route ::/0 2002:b428:702:: ipv route ::/0 2002:b428:702:: R1(config)#no ipv route ::/0 2002:b428:702::ipv route ::/0 2002:b428:702::    1:: R1(config)#^Z R1# *Mar 1 22:36:49.492: %SYS-5-CONFIG_I: Configured from console by console R1#p 2002:b428:701:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:701::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R1#configt Translating "configt" Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R1#configt % Unknown command or computer name, or unable to find computer address R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv route ::/0 2002:b428:701::nipv route ::/0 2002:b428:701::oipv route ::/0 2002:b428:701:: ipv route ::/0 2002:b428:701:: R1(config)#x  RACK12AS>7 [Resuming connection 7 to r7 ... ] *Ma R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv route ::/0 2002:b428:742::exit ipv route ::/0 2002:b428:742::nipv route ::/0 2002:b428:742::oipv route ::/0 2002:b428:742:: ipv route ::/0 2002:b428:742:: R7(config)#rotuer bgp          uter bgp 1 100 R7(config-router)#router bgp 100 nei     add ipv6 R7(config-router-af)#nei 2002:b428:742:: eb R7(config-router-af)#nei 2002:b428:742:: ebgp-multihop 2 R7(config-router-af)# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1(config)#router bgp 1 200 R1(config-router)#add ipv6 R1(config-router-af)#nei 2002:b428:701:: eb 2 R1(config-router-af)#^Z R1#sh run *Mar 1 22:38:26.194: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 22:38:26.883: %BGP-5-ADJCHANGE: neighbor 2002:B428:701:: Up R1#sh run | b            sh ipv route IPv6 Routing Table - 21 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::3/128 [120/3] via FE80::212:80FF:FE14:4D00, Serial0/1 R 2000:4:4::/64 [120/2] via FE80::20E:38FF:FEF1:63E0, Ethernet0/1 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:742::/64 [0/0] via ::, Tunnel0 L 2002:B428:742::/128 [0/0] via ::, Tunnel0 C 2005:0:102::/64 [0/0] via ::, Serial0/1 L 2005:0:102::1/128 [0/0] via ::, Serial0/1 C 2005:0:104::/64 [0/0] via ::, Ethernet0/1 L 2005:0:104::1/128 [0/0] --More--   via ::, Ethernet0/1 --More--  R 2005:0:237::/64 [120/2] --More--   R1# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#pin   ping 2006:7:7:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:7:7::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 120/135/164 ms R4#tre ace 2006:7:7:: Type escape sequence to abort. Tracing the route to 2006:7:7:: 1 2005:0:104::1 4 msec 0 msec 0 msec 2 2005:0:102::2 24 msec 24 msec 24 msec 3 2005:0:237::3 52 msec 68 msec 56 msec 4 2005:0:237::7 84 msec 84 msec 84 msec R4#sh bgp BGP table version is 6, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:104::1 0 0 200 i *> 2006:2:2::/128 2005:0:104::1 0 200 100 i *> 2006:3:3::/128 2005:0:104::1 0 200 100 i *> 2006:4:4::/128 :: 0 32768 i *> 2006:7:7::/128 2005:0:104::1 0 200 100 i R4# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#sh vg  bgp BGP table version is 7, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 :: 0 32768 i * 2006:2:2::/128 2002:B428:701:: 0 100 i *> 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2002:B428:701:: 0 100 i *> 2005:0:102::2 0 100 i *> 2006:4:4::/128 2005:0:104::4 0 0 300 i * 2006:7:7::/128 2002:B428:701:: 0 0 100 i *> 2005:0:102::2 0 100 i R1#configt Translating "configt" Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R1#in  config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 1/  0/1 R1(config-if)#shut R1(config-if)# *Mar 1 22:44:23.432: %BGP-5-ADJCHANGE: neighbor 2005:0:102::2 Down Interface flap R1(config-if)# *Mar 1 22:44:25.079: %LINK-5-CHANGED: Interface Serial0/1, changed state to administratively down *Mar 1 22:44:26.080: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to down R1(config-if)#do sh bgp BGP table version is 10, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 :: 0 32768 i *> 2006:2:2::/128 2002:B428:701:: 0 100 i *> 2006:3:3::/128 2002:B428:701:: 0 100 i *> 2006:4:4::/128 2005:0:104::4 0 0 300 i *> 2006:7:7::/128 2002:B428:701:: 0 0 100 i R1(config-if)#no shut R1(config-if)# *Mar 1 22:44:52.179: %LINK-3-UPDOWN: Interface Serial0/1, changed state to up *Mar 1 22:44:53.181: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up R1(config-if)#^Z R1#config tt *Mar 1 22:44:55.877: %SYS-5-CONFIG_I: Configured from console by console R1#configt sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 11, main routing table version 11 5 network entries using 665 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1241 total bytes of memory BGP activity 5/0 prefixes, 12/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 16 15 11 0 0 00:06:34 2 2005:0:102::2 4 100 44 45 0 0 0 00:00:37 Idle 2005:0:104::4 4 300 41 45 11 0 0 00:36:38 1 R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 11, main routing table version 11 5 network entries using 665 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1241 total bytes of memory BGP activity 5/0 prefixes, 12/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 16 15 11 0 0 00:06:43 2 2005:0:102::2 4 100 44 45 0 0 0 00:00:47 Active 2005:0:104::4 4 300 41 45 11 0 0 00:36:48 1 R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 11, main routing table version 11 5 network entries using 665 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1241 total bytes of memory BGP activity 5/0 prefixes, 12/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 16 15 11 0 0 00:06:45 2 2005:0:102::2 4 100 44 45 0 0 0 00:00:49 Active 2005:0:104::4 4 300 41 45 11 0 0 00:36:50 1 R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 11, main routing table version 11 5 network entries using 665 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1241 total bytes of memory BGP activity 5/0 prefixes, 12/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 16 15 11 0 0 00:06:47 2 2005:0:102::2 4 100 44 45 0 0 0 00:00:51 Active 2005:0:104::4 4 300 41 45 11 0 0 00:36:52 1 R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 11, main routing table version 11 5 network entries using 665 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1241 total bytes of memory BGP activity 5/0 prefixes, 12/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 16 15 11 0 0 00:06:49 2 2005:0:102::2 4 100 44 45 0 0 0 00:00:53 Active 2005:0:104::4 4 300 41 45 11 0 0 00:36:54 1 R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 11, main routing table version 11 5 network entries using 665 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1241 total bytes of memory BGP activity 5/0 prefixes, 12/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 16 15 11 0 0 00:06:51 2 2005:0:102::2 4 100 44 45 0 0 0 00:00:55 Active 2005:0:104::4 4 300 41 45 11 0 0 00:36:56 1 R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 11, main routing table version 11 5 network entries using 665 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1241 total bytes of memory BGP activity 5/0 prefixes, 12/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 16 15 11 0 0 00:06:54 2 2005:0:102::2 4 100 44 45 0 0 0 00:00:57 Active 2005:0:104::4 4 300 41 45 11 0 0 00:36:58 1 R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 11, main routing table version 11 5 network entries using 665 bytes of memory 4 path entries using 288 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1241 total bytes of memory BGP activity 5/0 prefixes, 12/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 16 15 11 0 0 00:06:56 2 2005:0:102::2 4 100 44 45 0 0 0 00:00:59 Active 2005:0:104::4 4 300 42 46 11 0 0 00:37:00 1 R1# *Mar 1 22:45:25.265: %BGP-5-ADJCHANGE: neighbor 2005:0:102::2 Up R1#sh bgp sum BGP router identifier 1.1.1.1, local AS number 200 BGP table version is 12, main routing table version 12 5 network entries using 665 bytes of memory 7 path entries using 504 bytes of memory 4 BGP path attribute entries using 240 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1457 total bytes of memory BGP activity 5/0 prefixes, 15/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2002:B428:701:: 4 100 17 17 12 0 0 00:07:01 2 2005:0:102::2 4 100 50 53 11 0 0 00:00:03 3 2005:0:104::4 4 300 42 47 12 0 0 00:37:06 1 R1#sh bgp sumconfig t t sh bgp ipv routebgp  BGP table version is 12, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 :: 0 32768 i *> 2006:2:2::/128 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2005:0:102::2 0 100 i *> 2002:B428:701:: 0 100 i *> 2006:4:4::/128 2005:0:104::4 0 0 300 i * 2006:7:7::/128 2005:0:102::2 0 100 i *> 2002:B428:701:: 0 0 100 i R1#sh bgp BGP table version is 12, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 :: 0 32768 i *> 2006:2:2::/128 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2005:0:102::2 0 100 i *> 2002:B428:701:: 0 100 i *> 2006:4:4::/128 2005:0:104::4 0 0 300 i * 2006:7:7::/128 2005:0:102::2 0 100 i *> 2002:B428:701:: 0 0 100 i R1# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#sh bgptrace 2006:7:7::ping 2006:7:7::  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:7:7::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 48/48/48 ms R4# RACK12AS>7 [Resuming connection 7 to r7 ... ] * R7(config-router-af)#^Z R7#ping 20 *Mar 1 22:45:20.818: %SYS-5-CONFIG_I: Configured from console by console R7#ping 2006:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:4:4::, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#router bgp 100 R7(config-router)#add ipv6 R7(config-router-af)#net 2002:b428:701:: % Incomplete command. R7(config-router-af)#net 2002:b428:701::/64 R7(config-router-af)#^Z R7# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#ping 2006:7:7::sh bgp  BGP table version is 8, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:104::1 0 0 200 i *> 2006:2:2::/128 2005:0:104::1 0 200 100 i *> 2006:3:3::/128 2005:0:104::1 0 200 100 i *> 2006:4:4::/128 :: 0 32768 i *> 2006:7:7::/128 2005:0:104::1 0 200 100 i R4#sh bgp BGP table version is 8, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:104::1 0 0 200 i *> 2006:2:2::/128 2005:0:104::1 0 200 100 i *> 2006:3:3::/128 2005:0:104::1 0 200 100 i *> 2006:4:4::/128 :: 0 32768 i *> 2006:7:7::/128 2005:0:104::1 0 200 100 i R4#sh bgp BGP table version is 8, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:104::1 0 0 200 i *> 2006:2:2::/128 2005:0:104::1 0 200 100 i *> 2006:3:3::/128 2005:0:104::1 0 200 100 i *> 2006:4:4::/128 :: 0 32768 i *> 2006:7:7::/128 2005:0:104::1 0 200 100 i R4#sh bgp BGP table version is 8, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2006:1:1::/128 2005:0:104::1 0 0 200 i *> 2006:2:2::/128 2005:0:104::1 0 200 100 i *> 2006:3:3::/128 2005:0:104::1 0 200 100 i *> 2006:4:4::/128 :: 0 32768 i *> 2006:7:7::/128 2005:0:104::1 0 200 100 i R4# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Ma R2# RACK12AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh bgp BGP table version is 14, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * i2006:1:1::/128 2005:0:102::1 0 100 0 200 i *> 2002:B428:742:: 0 0 200 i *>i2006:2:2::/128 2005:0:102::2 0 100 0 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i * i2006:4:4::/128 2005:0:102::1 0 100 0 200 300 i *> 2002:B428:742:: 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7#sh bgp BGP table version is 15, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2002:B428:701::/64 :: 0 32768 i * i2006:1:1::/128 2005:0:102::1 0 100 0 200 i *> 2002:B428:742:: 0 0 200 i *>i2006:2:2::/128 2005:0:102::2 0 100 0 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i * i2006:4:4::/128 2005:0:102::1 0 100 0 200 300 i *> 2002:B428:742:: 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7# R7# R7# R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#sh bgp BGP table version is 13, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2002:B428:701::/64 2005:0:102::2 0 100 i *> 2002:B428:701:: 0 0 100 i *> 2006:1:1::/128 :: 0 32768 i * 2006:2:2::/128 2002:B428:701:: 0 100 i *> 2005:0:102::2 0 0 100 i * 2006:3:3::/128 2005:0:102::2 0 100 i *> 2002:B428:701:: 0 100 i *> 2006:4:4::/128 2005:0:104::4 0 0 300 i * 2006:7:7::/128 2005:0:102::2 0 100 i *> 2002:B428:701:: 0 0 100 i R1#q  RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#sh bgpconfig tping 2006:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:4:4::, timeout is 2 seconds: . RACK12AS>7 4 [Resuming connection 4 to r4 ... ] R4#sh bgp BGP table version is 9, local router ID is 4.4.4.4 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path *> 2002:B428:701::/64 2005:0:104::1 0 200 100 i *> 2006:1:1::/128 2005:0:104::1 0 0 200 i *> 2006:2:2::/128 2005:0:104::1 0 200 100 i *> 2006:3:3::/128 2005:0:104::1 0 200 100 i *> 2006:4:4::/128 :: 0 32768 i *> 2006:7:7::/128 2005:0:104::1 0 200 100 i R4# RACK12AS>7 [Resuming connection 7 to r7 ... ] .. R7#ping 2006:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:4:4::, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) R7#sh ipv route IPv6 Routing Table - 21 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::3/128 [110/781] via FE80::3, Serial1/0.1 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] --More--   via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::212:80FF:FE14:4D00, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 B 2006:1:1::/128 [20/0] via 2002:B428:742:: B 2006:2:2::/128 [200/0] via 2005:0:102::2 B 2006:3:3::/128 [200/0] via 2000:3:3::3 B 2006:4:4::/128 [20/0] via 2002:B428:742:: LC 2006:7:7::/128 [0/0] via ::, Loopback1 L FE80::/10 [0/0] --More--   via ::, Null0 --More--  L FF00::/8 [0/0] --More--   via ::, Null0 R7# R7# R7# R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#sh ipv route IPv6 Routing Table - 22 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::3/128 [120/3] via FE80::212:80FF:FE14:4D00, Serial0/1 R 2000:4:4::/64 [120/2] via FE80::20E:38FF:FEF1:63E0, Ethernet0/1 S 2002::/16 [1/0] via ::, Tunnel0 B 2002:B428:701::/64 [20/0] via 2002:B428:701:: C 2002:B428:742::/64 [0/0] via ::, Tunnel0 L 2002:B428:742::/128 [0/0] via ::, Tunnel0 C 2005:0:102::/64 [0/0] via ::, Serial0/1 L 2005:0:102::1/128 [0/0] via ::, Serial0/1 C 2005:0:104::/64 [0/0] --More--   via ::, Ethernet0/1 L 2005:0:104::1/128 [0/0] via ::, Ethernet0/1 R 2005:0:237::/64 [120/2] via FE80::212:80FF:FE14:4D00, Serial0/1 R 2005:0:237::3/128 [120/3] via FE80::212:80FF:FE14:4D00, Serial0/1 R 2005:0:702::/64 [120/2] via FE80::212:80FF:FE14:4D00, Serial0/1 R 2005:0:1203::/64 [120/2] via FE80::212:80FF:FE14:4D00, Serial0/1 R 2005:0:1203::3/128 [120/3] via FE80::212:80FF:FE14:4D00, Serial0/1 LC 2006:1:1::/128 [0/0] via ::, Loopback1 B 2006:2:2::/128 [20/0] via FE80::212:80FF:FE14:4D00, Serial0/1 B 2006:3:3::/128 [20/0] via 2002:B428:701:: B 2006:4:4::/128 [20/0] via FE80::20E:38FF:FEF1:63E0, Ethernet0/1 B 2006:7:7::/128 [20/0] via 2002:B428:701:: --More--  L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R1# via 2002:B428:742:: ^ % Invalid input detected at '^' marker. R1# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#sh ipb v route IPv6 Routing Table - 19 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::3/128 [120/4] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::4/128 [0/0] via ::, Loopback0 B 2002:B428:701::/64 [20/0] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 R 2005:0:102::/64 [120/2] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:237::/64 [120/3] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 R 2005:0:237::3/128 [120/4] --More--   R4# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#sh ipv routeping 2006:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:4:4::, timeout is 2 seconds: .. Success rate is 0 percent (0/2) R7#trace 2006:4:4:: Type escape sequence to abort. Tracing the route to 2006:4:4:: 1 * * * 2 * * R7#ping       *Mar 1 22:49:36.689: BGP: 2002:B428:742:: connection timed out 180491ms (last update) 180000ms (hold time) *Mar 1 22:49:36.689: BGP: 2002:B428:742:: went from Established to Closing *Mar 1 22:49:36.689: %BGP-5-ADJCHANGE: neighbor 2002:B428:742:: Down BGP Notification sent *Mar 1 22:49:36.689: %BGP-3-NOTIFICATION: sent to neighbor 2002:B428:742:: 4/0 (hold time expired) 0 bytes R7# *Mar 1 22:49:36.689: BGP: 2002:B428:742:: send message type 3, length (incl. header) 21 *Mar 1 22:49:37.691: BGP: 2002:B428:742:: local error close after sending NOTIFICATION R7# *Mar 1 22:49:38.692: BGPNSF state: 2002:B428:742:: went from nsf_not_active to nsf_not_active *Mar 1 22:49:38.692: BGP: 2002:B428:742:: went from Closing to Idle *Mar 1 22:49:38.692: BGP: 2002:B428:742:: closing R7# *Mar 1 22:49:58.829: BGP: 2002:B428:742:: went from Idle to Active *Mar 1 22:49:58.829: BGP: 2002:B428:742:: open active, delay 17949ms R7# *Mar 1 22:50:16.779: BGP: 2002:B428:742:: open active, local address 2002:B428:701:: *Mar 1 22:50:16.835: BGP: 2002:B428:742:: went from Active to OpenSent *Mar 1 22:50:16.835: BGP: 2002:B428:742:: sending OPEN, version 4, my as: 100 *Mar 1 22:50:16.839: BGP: 2002:B428:742:: send message type 1, length (incl. header) 45 *Mar 1 22:50:16.935: BGP: 2002:B428:742:: rcv message type 1, length (excl. header) 26 *Mar 1 22:50:16.935: BGP: 2002:B428:742:: rcv OPEN, version 4 *Mar 1 22:50:16.939: BGP: 2002:B428:742:: rcv OPEN w/ OPTION parameter len: 16 *Mar 1 22:50:16.939: BGP: 2002:B428:742:: rcvd OPEN w/ optional parameter type 2 (Capability) len 6 *Mar 1 22:50:16.939: BGP: 2002:B428:742:: OPEN has CAPABILITY code: 1, length 4 *Mar 1 22:50:16.939: BGP: 2002:B428:742:: OPEN has MP_EXT CAP for afi/safi: 2/1 *Mar 1 22:50:16.939: BGP: 2002:B428:742:: rcvd OPEN w/ optional parameter type 2 (Capability) len 2 *Mar 1 22:50:16.939: BGP: 2002:B428:742:: OPEN has CAPABILITY co R7#de: 128, length 0 *Mar 1 22:50:16.939: BGP: 2002:B428:742:: OPEN has ROUTE-REFRESH capability(old) for all address-families *Mar 1 22:50:16.939: BGP: 2002:B428:742:: rcvd OPEN w/ optional parameter type 2 (Capability) len 2 *Mar 1 22:50:16.939: BGP: 2002:B428:742:: OPEN has CAPABILITY code: 2, length 0 *Mar 1 22:50:16.939: BGP: 2002:B428:742:: OPEN has ROUTE-REFRESH capability(new) for all address-families *Mar 1 22:50:16.943: BGP: 2002:B428:742:: went from OpenSent to OpenConfirm *Mar 1 22:50:16.943: BGP: 2002:B428:742:: went from OpenConfirm to Established *Mar 1 22:50:16.943: %BGP-5-ADJCHANGE: neighbor 2002:B428:742:: Up R7# R7# R7# R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#rotuer bgp          uter bgp 100 R7(config-router)#add ipv  6 R7(config-router-af)#add ipv6router bgp 100net 2002:b428:701::/64nnet 2002:b428:701::/64onet 2002:b428:701::/64 net 2002:b428:701::/64 R7(config-router-af)#^Z R7# RACK12AS> [Resuming connection 7 to r7 ... ] *Mar 1 22:50:46.692: %SYS-5-CONFIG_I: Configured from console by console R7# R7#1 Trying 1... % Destination unreachable; gateway or host down % Unknown command or computer name, or unable to find computer address R7# R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] *M R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#do sh ip  run | b pref distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1(config)#q config t ^ % Invalid input detected at '^' marker. R1(config)#ipipv6 prefix-list Prob3 seq ipipv6 prefix-list Prob3 seq pv6 prefix-list Prob3 seq ipv6 prefix-list Prob3 seq 7 den 2002::/16 le 128 R1(config)#ipv router rip R1Rip R1(config-rtr)#redi stati R1(config-rtr)#redi static ? metric Metric for redistributed routes route-map Route map reference R1(config-rtr)#redi static me 2 R1(config-rtr)#^Z R1# *Mar 1 22:52:52.851: %SYS-5-CONFIG_I: Configured from console by console R1# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#sh ipv route IPv6 Routing Table - 19 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::3/128 [120/4] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::4/128 [0/0] via ::, Loopback0 R 2002::/16 [120/3] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 R 2005:0:102::/64 [120/2] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:237::/64 [120/3] via FE80::202:FDFF:FE79:C2A1, FastEthernet0/0 R 2005:0:237::3/128 [120/4] --More--   R4# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#sh bgp sum BGP router identifier 7.7.7.7, local AS number 100 BGP table version is 20, main routing table version 20 5 network entries using 665 bytes of memory 7 path entries using 504 bytes of memory 6 BGP path attribute entries using 360 bytes of memory 1 BGP rrinfo entries using 24 bytes of memory 2 BGP AS-PATH entries using 48 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 1601 total bytes of memory BGP activity 7/2 prefixes, 15/8 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 2000:3:3::3 4 100 63 69 20 0 0 00:42:06 4 2002:B428:742:: 4 200 30 37 20 0 0 00:02:01 2 R7#sh bgp sum1 config ttrace 2006:4:4:: Type escape sequence to abort. Tracing the route to 2006:4:4:: 1 2002:B428:742:: 0 msec 4 msec 4 msec 2 2005:0:104::4 8 msec 4 msec 8 msec R7#trace 2006:4:4::sh bgp sum 1 config ttrace 2006:4:4::ping 2006:4:4::  Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b Tu interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:742::/64 keepalive 10 3 tunnel source Ethernet0/0 tunnel mode ipv6ip 6to4 ! interface Ethernet0/0 ip address 180.40.7.66 255.255.255.224 half-duplex ! interface Serial0/0 no ip address shutdown ! interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::1/64 ipv6 rip R1Rip enable ! interface Serial0/1 --More--   no ip address ipv6 address 2005:0:102::1/64 ipv6 rip R1Rip enable clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! router bgp 200 no synchronization bgp router-id 1.1.1.1 bgp log-neighbor-changes neighbor 2002:B428:701:: remote-as 100 neighbor 2002:B428:701:: ebgp-multihop 2 no neighbor 2002:B428:701:: activate neighbor 2005:0:102::2 remote-as 100 no neighbor 2005:0:102::2 activate neighbor 2005:0:104::4 remote-as 300 no neighbor 2005:0:104::4 activate no auto-summary ! --More--   address-family ipv6 neighbor 2002:B428:701:: activate neighbor 2005:0:102::2 activate neighbor 2005:0:104::4 activate network 2006:1:1::/128 exit-address-family ! no ip http server ip classless ! ! ipv6 route 2002::/16 Tunnel0 ipv6 router rip R1Rip redistribute static metric 2 distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 7 deny 2002::/16 le 128 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ! ! --More--   R1# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b Tu interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:701::/64 ipv6 rip R7Rip enable keepalive 10 3 tunnel source FastEthernet0/1 tunnel mode ipv6ip 6to4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.1 255.255.255.224 duplex auto speed auto --More--  ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80::7 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::7/64 ipv6 ospf 1 area 0 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown --More--  ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router rip version 2 --More--   network 180.40.0.0 no auto-summary ! router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: activate network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv pre R7(config)#ipv prefix-list per     ProbD per 2006:4:4::/128 R7(config)#route-map R7(config)#route-map ProbD R7(config-route-map)#match ipvadd ProbD ^ % Invalid input detected at '^' marker. R7(config-route-map)#match ipvadd ProbD add ProbD R7(config-route-map)#set loca R7(config-route-map)#set local-preference 90 R7(config-route-map)#set local-preference 90match ipv add ProbD add ProbD route-map ProbD  20 R7(config-route-map)#router bgp 100 R7(config-router)#addi  ipv  6 R7(config-router-af)#nei 2002:b428:742:: route R7(config-router-af)#nei 2002:b428:742:: route-m R7(config-router-af)#nei 2002:b428:742:: route-map ProbD in R7(config-router-af)#^Z R7#clea *Mar 1 23:00:46.659: %SYS-5-CONFIG_I: Configured from console by console R7#clea ip    bgp * in R7# *Mar 1 23:00:52.365: BGP: 2000:3:3::3 sending REFRESH_REQ(5) for afi/safi: 2/1 *Mar 1 23:00:52.365: BGP: 2002:B428:742:: sending REFRESH_REQ(5) for afi/safi: 2/1 *Mar 1 23:00:52.365: BGP: 2000:3:3::3 send message type 5, length (incl. header) 23 *Mar 1 23:00:52.365: BGP: 2002:B428:742:: send message type 5, length (incl. header) 23 R7#sh vf     deb     u all All possible debugging has been turned off R7#sh bf gp BGP table version is 22, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2006:1:1::/128 2002:B428:742:: 0 90 0 200 i *>i 2005:0:102::1 0 100 0 200 i *>i2006:2:2::/128 2005:0:102::2 0 100 0 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i * 2006:4:4::/128 2002:B428:742:: 90 0 200 300 i *>i 2005:0:102::1 0 100 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7# R7# R7# R7# R7#sh bgpu all clea bgp * inonfig t sh run | b Tuping 2006:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2006:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/89/92 ms R7#ping 2006:4:4::sh bgp u all clea bgp * inonfig t sh run | b Tuping 2006:4:4::trace 2006:4:4:: Type escape sequence to abort. Tracing the route to 2006:4:4:: 1 2005:0:702::2 44 msec 44 msec 45 msec 2 2005:0:102::1 68 msec 64 msec 68 msec 3 2005:0:104::4 68 msec 68 msec 64 msec R7#sh run | b bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: activate neighbor 2002:B428:742:: route-map ProbD in network 2006:7:7::/128 exit-address-family ! ip classless ! no ip http server no ip http secure-server ! --More--  ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! ipv6 router rip R7Rip ! ! ! ipv6 prefix-list ProbD seq 5 permit 2006:4:4::/128 route-map ProbD permit 10 match ipv6 address ProbD set local-preference 90 ! route-map ProbD permit 20 ! ! ! ! ! ! ! ! --More--   R7#configt Translating "configt" Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip as R7(config)#ip as-path ac R7(config)#ip as-path access-list 1 ? deny Specify packets to reject permit Specify packets to forward R7(config)#ip as-path access-list 1 per _200$     ^200$ R7(config)#route-map ProbE R7(config-route-map)#a match ad R7(config-route-map)#match ad s R7(config-route-map)#match as-path 1 R7(config-route-map)#set as R7(config-route-map)#set as-path p R7(config-route-map)#set as-path prepend ? <1-65535> AS number last-as Prepend last AS to the as-path R7(config-route-map)#set as-path prepend 200 2002 0    200 200 200 R7(config-route-map)#set as-path prepend 200 200 200 200 200match as-path 1 route-map ProbE 20 R7(config-route-map)#rotuer      uter bpg 100 ^ % Invalid input detected at '^' marker. R7(config)#router bpg 100-map ProbE 20r bpg 100  router bpg 100 100  100 g 100p 100 R7(config-router)#addd ipv      ipv6 R7(config-router-af)#exit R7(config-router)#exitadd ipv6router bgp 100pg 100-map ProbE 20nroute-map ProbE 20oroute-map ProbE 20 route-map ProbE 20route-map ProbE 20   R7(config)#do sh ru  n | i route-map neighbor 2002:B428:742:: route-map ProbD in route-map ProbD permit 10 route-map ProbD permit 20 R7(config)#route-map ProbD permit 20 R7(config-route-map)#route-map ProbD permit 20do sh run | i route-map no route-map ProbE exit add ipv6router bgp 100pg 100-map ProbE 20set as-path prepend 200 200 200 200 200match as-path 1  R7(config-route-map)#match as-path 1route-map ProbD permit 20do sh run | i route-map no route-map ProbE exit add ipv6router bgp 100pg 100-map ProbE 20set as-path prepend 200 200 200 200 200 R7(config-route-map)#set as-path prepend 200 200 200 200 200match as-path 1 route-map ProbD permit 20do sh run | i route-map route-map ProbD permit 20  30 R7(config-route-map)#^Z R7# *Mar 1 23:08:04.273: %SYS-5-CONFIG_I: Configured from console by console R7#clea bgp * in R7#sh bgp BGP table version is 22, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2006:1:1::/128 2002:B428:742:: 0 90 0 200 i *>i 2005:0:102::1 0 100 0 200 i *>i2006:2:2::/128 2005:0:102::2 0 100 0 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i * 2006:4:4::/128 2002:B428:742:: 90 0 200 300 i *>i 2005:0:102::1 0 100 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7#sh bgp sh bgp sh bgp BGP table version is 22, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2006:1:1::/128 2002:B428:742:: 0 90 0 200 i *>i 2005:0:102::1 0 100 0 200 i *>i2006:2:2::/128 2005:0:102::2 0 100 0 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i * 2006:4:4::/128 2002:B428:742:: 90 0 200 300 i *>i 2005:0:102::1 0 100 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7#sh run | b bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: activate neighbor 2002:B428:742:: route-map ProbD in network 2006:7:7::/128 exit-address-family ! ip classless ! ip as-path access-list 1 permit ^200$ no ip http server no ip http secure-server --More--  ! ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! ipv6 router rip R7Rip ! ! ! ipv6 prefix-list ProbD seq 5 permit 2006:4:4::/128 route-map ProbD permit 10 match ipv6 address ProbD set local-preference 90 ! route-map ProbD permit 20 match as-path 1 set as-path prepend 200 200 200 200 200 ! route-map ProbD permit 30 ! ! ! --More--   R7#sh ip as   R7#sh ip as-path-access-list AS path access list 1 permit ^200$ R7#sh ip as-path-access-list run | b bgp  router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: activate neighbor 2002:B428:742:: route-map ProbD in network 2006:7:7::/128 exit-address-family ! ip classless ! ip as-path access-list 1 permit ^200$ no ip http server no ip http secure-server --More--   R7#q ~ sh bgp BGP table version is 22, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2006:1:1::/128 2002:B428:742:: 0 90 0 200 i *>i 2005:0:102::1 0 100 0 200 i *>i2006:2:2::/128 2005:0:102::2 0 100 0 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i * 2006:4:4::/128 2002:B428:742:: 90 0 200 300 i *>i 2005:0:102::1 0 100 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7#sh bgprun | b bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: activate neighbor 2002:B428:742:: route-map ProbD in network 2006:7:7::/128 exit-address-family ! ip classless ! ip as-path access-list 1 permit ^200$ no ip http server no ip http secure-server --More--  ! ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! ipv6 router rip R7Rip ! ! ! ipv6 prefix-list ProbD seq 5 permit 2006:4:4::/128 route-map ProbD permit 10 match ipv6 address ProbD set local-preference 90 ! route-map ProbD permit 20 match as-path 1 set as-path prepend 200 200 200 200 200 ! route-map ProbD permit 30 ! ! ! --More--  ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#route-map ProbD permit 30    10 R7(config-route-map)#no match ipv6 address ProbD R7(config-route-map)#no match ipv6 address ProbDpProbDrProbDeProbD ProbDmatch ipv6 address pre ProbD  match ipv6 address pre ProbD  match ipv6 address pre ProbD  R7(config-route-map)#^Z R7# *Mar 1 23:10:59.973: %SYS-5-CONFIG_I: Configured from console by console R7#clea ip    bgp * in R7#clea bgp * inonfig t sh run | b bgpbgp  BGP table version is 22, local router ID is 7.7.7.7 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path * 2006:1:1::/128 2002:B428:742:: 0 0 200 200 200 200 200 200 i *>i 2005:0:102::1 0 100 0 200 i *>i2006:2:2::/128 2005:0:102::2 0 100 0 i *>i2006:3:3::/128 2000:3:3::3 0 100 0 i * 2006:4:4::/128 2002:B428:742:: 90 0 200 300 i *>i 2005:0:102::1 0 100 0 200 300 i *> 2006:7:7::/128 :: 0 32768 i R7#sh ru n|    bgpclea bgp * inonfig t sh run | b bgp router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: activate neighbor 2002:B428:742:: route-map ProbD in network 2006:7:7::/128 exit-address-family ! ip classless ! ip as-path access-list 1 permit ^200$ no ip http server no ip http secure-server --More--  ! ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! ipv6 router rip R7Rip ! ! ! ipv6 prefix-list ProbD seq 5 permit 2006:4:4::/128 route-map ProbD permit 10 match ipv6 address prefix-list ProbD set local-preference 90 ! route-map ProbD permit 20 match as-path 1 set as-path prepend 200 200 200 200 200 ! route-map ProbD permit 30 ! ! ! --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#ipv nat R7(config)#ipv nat ? max-entries Specify maximum number of NAT-PT entries prefix Configure a global NAT-PT prefix service ALG specific translation NAT-PT translation entry configuration v4v6 IPv4 to IPv6 translation v6v4 IPv6 to IPv4 translation R7(config)#ipv nat pre R7(config)#ipv nat prefix ? X:X:X:X::X/<0-128> IPv6 prefix x:x::y/ R7(config)#ipv nat prefix 20 666:^^^   666:666::/64 % Invalid prefix length R7(config)#ipv nat prefix 2666:666:666::/64 5 % Invalid prefix length R7(config)#ipv nat prefix 2666:666:666::/65 6 % Invalid prefix length R7(config)#ipv nat prefix 2666:666:666::/66  96 R7(config)#do sh ii pv route IPv6 Routing Table - 22 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::3/128 [110/781] via FE80::3, Serial1/0.1 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] --More--   via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::212:80FF:FE14:4D00, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 B 2006:1:1::/128 [200/0] via 2005:0:102::1 B 2006:2:2::/128 [200/0] via 2005:0:102::2 B 2006:3:3::/128 [200/0] via 2000:3:3::3 B 2006:4:4::/128 [200/0] via 2005:0:102::1 LC 2006:7:7::/128 [0/0] via ::, Loopback1 C 2666:666:666::/96 [0/0] --More--   via ::, Null0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7(config)#ip route 33.33.33.0 255.255.255.0 null 0 R7(config)#router rip R7(config-router)#redi is R7(config-router)#redistribute st R7(config-router)#redistribute static 2 ^ % Invalid input detected at '^' marker. R7(config-router)#redistribute static 2 m R7(config-router)#redistribute static metric 2 R7(config-router)# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/7 C 180.40.7.32 is directly connected, FastEthernet0/24 R 180.40.7.64 [120/1] via 180.40.7.34, 00:00:20, FastEthernet0/24 S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/7 C 180.40.7.32 is directly connected, FastEthernet0/24 R 180.40.7.64 [120/1] via 180.40.7.34, 00:00:23, FastEthernet0/24 S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/7 C 180.40.7.32 is directly connected, FastEthernet0/24 R 180.40.7.64 [120/1] via 180.40.7.34, 00:00:25, FastEthernet0/24 S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/7 C 180.40.7.32 is directly connected, FastEthernet0/24 R 180.40.7.64 [120/1] via 180.40.7.34, 00:00:27, FastEthernet0/24 S6# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7(config-router)#do sh       do sh ip proto Routing Protocol is "rip" Sending updates every 30 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: static, rip Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain FastEthernet0/1 2 2 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 180.40.0.0 Routing Information Sources: Gateway Distance Last Update 180.40.7.2 120 00:00:17 Distance: (default is 120) Routing Protocol is "bgp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set IGP synchronization is disabled Automatic route summarization is disabled --More--   Maximum path: 1 Routing Information Sources: Gateway Distance Last Update Distance: external 20 internal 200 local 200 R7(config-router)# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/7 C 180.40.7.32 is directly connected, FastEthernet0/24 R 180.40.7.64 [120/1] via 180.40.7.34, 00:00:00, FastEthernet0/24 S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/7 C 180.40.7.32 is directly connected, FastEthernet0/24 R 180.40.7.64 [120/1] via 180.40.7.34, 00:00:09, FastEthernet0/24 S6#sh ip route RACK12AS>7 [Resuming connection 7 to r7 ... ] R7(config-router)#do deb ip rip RIP protocol debugging is on R7(config-router)# *Mar 1 23:19:40.714: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:19:40.714: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:19:40.714: 180.40.7.64/27 via 0.0.0.0 in 2 hops R7(config-router)#do sh run | b router router rip version 2 redistribute static metric 2 network 180.40.0.0 no auto-summary ! router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: activate neighbor 2002:B428:742:: route-map ProbD in network 2006:7:7::/128 exit-address-family --More-- *Mar 1 23:20:07.306: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:20:07.306: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:20:07.310: 180.40.7.64/27 via 0.0.0.0 in 2 hops --More--  ! ip classless ip route 33.33.33.0 255.255.255.0 Null0 ! ip as-path access-list 1 permit ^200$ no ip http server no ip http secure-server ! ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes ! ipv6 router rip R7Rip ! ipv6 nat prefix 2666:666:666::/96 ! ! ipv6 prefix-list ProbD seq 5 permit 2006:4:4::/128 route-map ProbD permit 10 match ipv6 address prefix-list ProbD set local-preference 90 ! --More--  route-map ProbD permit 20 match as-path 1 set as-path prepend 200 200 200 200 200 ! route-map ProbD permit 30 ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! --More-- *Mar 1 23:20:35.512: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:20:35.512: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:20:35.512: 180.40.7.64/27 via 0.0.0.0 in 2 hops --More--   R7(config-router)#do u all All possible debugging has been turned off R7(config-router)#do sh ip rout Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 33.0.0.0/24 is subnetted, 1 subnets S 33.33.33.0 is directly connected, Null0 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/1 R 180.40.7.32 [120/1] via 180.40.7.2, 00:00:11, FastEthernet0/1 R 180.40.7.64 [120/2] via 180.40.7.2, 00:00:11, FastEthernet0/1 R7(config-router)#do sh ip routu all sh run | b routerdeb ip rip  RIP protocol debugging is on R7(config-router)#do clea ip rout * R7(config-router)# *Mar 1 23:21:26.456: RIP: sending request on FastEthernet0/1 to 224.0.0.9 *Mar 1 23:21:26.460: RIP: sending request on FastEthernet0/1 to 224.0.0.9 *Mar 1 23:21:26.460: RIP: sending request on FastEthernet0/1 to 224.0.0.9 *Mar 1 23:21:26.460: RIP: sending request on FastEthernet0/1 to 224.0.0.9 *Mar 1 23:21:26.476: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:21:26.476: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:21:26.476: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 23:21:26.476: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:21:26.480: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:21:26.480: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 23:21:26.480: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:21:26.480: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:21:26.480: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 23:21:26.480: RIP: received v2 update from 180.40 R7(config-rout.7.2 on FastEthernet0/1 *Mar 1 23:21:26.480: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:21:26.484: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 23:21:26.484: RIP: sending request on FastEthernet0/1 to 224.0.0.9 *Mar 1 23:21:26.488: RIP: sending request on FastEthernet0/1 to 224.0.0.9 *Mar 1 23:21:26.488: RIP: sending request on FastEthernet0/1 to 224.0.0.9 *Mar 1 23:21:26.488: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:21:26.492: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:21:26.492: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 23:21:26.492: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:21:26.492: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:21:26.492: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 23:21:26.492: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:21:26.492: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:21:26.496: 180.40.7.64/27 via 0.0.0.0 in 2 hopser)# R7(config-router)# *Mar 1 23:21:28.459: RIP: sending v2 flash update to 224.0.0.9 via FastEthernet0/1 (180.40.7.1) *Mar 1 23:21:28.459: RIP: build flash update entries - suppressing null update R7(config-router)# *Mar 1 23:21:30.001: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:21:30.001: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:21:30.001: 180.40.7.64/27 via 0.0.0.0 in 2 hops *Mar 1 23:21:30.791: RIP: sending v2 flash update to 224.0.0.9 via FastEthernet0/1 (180.40.7.1) *Mar 1 23:21:30.791: RIP: build flash update entries *Mar 1 23:21:30.791: 33.33.33.0/24 via 0.0.0.0, metric 2, tag 0 R7(config-router)# R7(config-router)# R7(config-router)# R7(config-router)# R7(config-router)# RACK12AS>6 [Resuming connection 6 to r6 ... ] Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 33.0.0.0/24 is subnetted, 1 subnets R 33.33.33.0 [120/2] via 180.40.7.1, 00:00:13, FastEthernet0/7 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/7 C 180.40.7.32 is directly connected, FastEthernet0/24 R 180.40.7.64 [120/1] via 180.40.7.34, 00:00:22, FastEthernet0/24 S6# S6# S6# S6# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6# RACK12AS>7 [Resuming connection 7 to r7 ... ] *Ma R7(config-router)# *Mar 1 23:21:59.534: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:21:59.534: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:21:59.534: 180.40.7.64/27 via 0.0.0.0 in 2 hops R7(config-router)#do sh ip proto Routing Protocol is "rip" Sending updates every 30 seconds, next due in 11 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: static, rip Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain FastEthernet0/1 2 2 Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 180.40.0.0 Routing Information Sources: Gateway Distance Last Update 180.40.7.2 120 00:00:08 Distance: (default is 120) Routing Protocol is "bgp 100" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set IGP synchronization is disabled Automatic route summarization is disabled --More--   R7(config-router)# *Mar 1 23:22:18.866: RIP: sending v2 update to 224.0.0.9 via FastEthernet0/1 (180.40.7.1) *Mar 1 23:22:18.866: RIP: build update entries *Mar 1 23:22:18.866: 33.33.33.0/24 via 0.0.0.0, metric 2, tag 0 R7(config-router)#do u all All possible debugging has been turned off R7(config-router)# *Mar 1 23:22:28.722: RIP: received v2 update from 180.40.7.2 on FastEthernet0/1 *Mar 1 23:22:28.722: 180.40.7.32/27 via 0.0.0.0 in 1 hops *Mar 1 23:22:28.722: 180.40.7.64/27 via 0.0.0.0 in 2 hops R7(config-router)# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 33.0.0.0/24 is subnetted, 1 subnets R 33.33.33.0 [120/2] via 180.40.7.1, 00:00:15, FastEthernet0/7 180.40.0.0/27 is subnetted, 3 subnets C 180.40.7.0 is directly connected, FastEthernet0/7 C 180.40.7.32 is directly connected, FastEthernet0/24 R 180.40.7.64 [120/1] via 180.40.7.34, 00:00:15, FastEthernet0/24 S6# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7(config-router)#exit R7(config)#ipv rp  pre R7(config)#ipv prefix-list ProbF per 2666:666:666:                                       do sh ipv route IPv6 Routing Table - 22 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::3/128 [110/781] via FE80::3, Serial1/0.1 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] --More--   via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::212:80FF:FE14:4D00, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 B 2006:1:1::/128 [200/0] via 2005:0:102::1 B 2006:2:2::/128 [200/0] via 2005:0:102::2 B 2006:3:3::/128 [200/0] via 2000:3:3::3 B 2006:4:4::/128 [200/0] via 2005:0:102::1 LC 2006:7:7::/128 [0/0] via ::, Loopback1 C 2666:666:666::/96 [0/0] --More--   via ::, Null0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7(config)#ipv pre R7(config)#ipv prefix-list ProbF per 2666:666:666::/96 R7(config)#router osp          ipv router ospf 1 R7(config-rtr)#redis R7(config-rtr)#redistribute con R7(config-rtr)#redistribute connected R7(config-rtr)#distr R7(config-rtr)#distribute-list p R7(config-rtr)#distribute-list prefix-list ProbF out con R7(config-rtr)#distribute-list prefix-list ProbF out connected R7(config-rtr)# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#sh ipv route IPv6 Routing Table - 19 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3::3/128 [0/0] via ::, Loopback0 OE2 2002:B428:701::/64 [110/20] via FE80::7, Serial1/0 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/2 via FE80::2, Serial1/0 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/2 via FE80::2, Serial1/0 C 2005:0:237::/64 [0/0] via ::, Serial1/0 L 2005:0:237::3/128 [0/0] via ::, Serial1/0 O 2005:0:702::/64 [110/1562] --More--   via FE80::212:80FF:FE14:4D00, Serial1/2 via FE80::2, Serial1/0 via FE80::7, Serial1/0 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/2 L 2005:0:1203::3/128 [0/0] via ::, Serial1/2 B 2006:1:1::/128 [200/0] via 2005:0:102::1 B 2006:2:2::/128 [200/0] via 2005:0:102::2 LC 2006:3:3::/128 [0/0] via ::, Loopback1 B 2006:4:4::/128 [200/0] via 2005:0:102::1 B 2006:7:7::/128 [200/0] via 2005:0:237::7 OE2 2666:666:666::/96 [110/20] via FE80::7, Serial1/0 L FE80::/10 [0/0] via ::, Null0 --More--  L FF00::/8 [0/0] via ::, Null0 R3# sh ipv route IPv6 Routing Table - 18 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3::3/128 [0/0] via ::, Loopback0 OE2 2005:0:102::/64 [110/20] via FE80::212:80FF:FE14:4D00, Serial1/2 via FE80::2, Serial1/0 OE2 2005:0:104::/64 [110/20], tag 2 via FE80::212:80FF:FE14:4D00, Serial1/2 via FE80::2, Serial1/0 C 2005:0:237::/64 [0/0] via ::, Serial1/0 L 2005:0:237::3/128 [0/0] via ::, Serial1/0 O 2005:0:702::/64 [110/1562] via FE80::212:80FF:FE14:4D00, Serial1/2 via FE80::2, Serial1/0 --More--   via FE80::7, Serial1/0 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203::2/128 [110/781] via FE80::212:80FF:FE14:4D00, Serial1/2 L 2005:0:1203::3/128 [0/0] via ::, Serial1/2 B 2006:1:1::/128 [200/0] via 2005:0:102::1 B 2006:2:2::/128 [200/0] via 2005:0:102::2 LC 2006:3:3::/128 [0/0] via ::, Loopback1 B 2006:4:4::/128 [200/0] via 2005:0:102::1 B 2006:7:7::/128 [200/0] via 2005:0:237::7 OE2 2666:666:666::/96 [110/20] via FE80::7, Serial1/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R3# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7(config-rtr)#exit R7(config)#ipv nat ? max-entries Specify maximum number of NAT-PT entries prefix Configure a global NAT-PT prefix service ALG specific translation NAT-PT translation entry configuration v4v6 IPv4 to IPv6 translation v6v4 IPv6 to IPv4 translation R7(config)#ipv nat v6 R7(config)#ipv nat v6v4 ? pool Configure a IPv4 address pool source Source Address Translation R7(config)#ipv nat v6v4 sou R7(config)#ipv nat v6v4 source ? X:X:X:X::X IPv6 address to translate list Specify access list route-map Configure a route-map R7(config)#ipv nat v6v4 source 2005:0:237::3 ? A.B.C.D IPv4 Address R7(config)#ipv nat v6v4 source 2005:0:237::3 33.33.33.33 R7(config)#ipv nat v6v4 source 2005:0:237::3 33.33.33.33 ipv nat v4 R7(config)#ipv nat v4v6 ? pool Configure a IPv6 address pool source Source Address Translation R7(config)#ipv nat v4v6 sou ? A.B.C.D IPv4 address to translate list Specify access list R7(config)#ipv nat v4v6 sou                  access0 -list 1 per 18-0.  0  0.40.7.2 R7(config)#access-list 1 per 180.40.7.2  .33 R7(config)#ipv nat v4 R7(config)#ipv nat v4v6 ? pool Configure a IPv6 address pool source Source Address Translation R7(config)#ipv nat v4v6 sou R7(config)#ipv nat v4v6 source ? A.B.C.D IPv4 address to translate list Specify access list R7(config)#ipv nat v4v6 source li R7(config)#ipv nat v4v6 source list ? <1-199> Access list number WORD Access list name R7(config)#ipv nat v4v6 source list 1 ? pool Specify pool name R7(config)#ipv nat v4v6 source list 1 pool ? WORD Pool name for global addresses R7(config)#ipv nat v4v6 source list 1 pool                                 ipv R7(config)#ipv6 n R7(config)#ipv6 na R7(config)#ipv6 nat ? max-entries Specify maximum number of NAT-PT entries prefix Configure a global NAT-PT prefix service ALG specific translation NAT-PT translation entry configuration v4v6 IPv4 to IPv6 translation v6v4 IPv6 to IPv4 translation R7(config)#ipv6 nat ve 4 R7(config)#ipv6 nat v4v6 po R7(config)#ipv6 nat v4v6 pool ? WORD Pool name R7(config)#ipv6 nat v4v6 pool ProbF ? X:X:X:X::X Start IPv6 address R7(config)#ipv6 nat v4v6 pool ProbF 2666:666:666::6 ? X:X:X:X::X End IPv6 address R7(config)#ipv6 nat v4v6 pool ProbF 2666:666:666::6 2666:666:666::66 ? prefix-length Specify the prefix length R7(config)#ipv6 nat v4v6 pool ProbF 2666:666:666::6 2666:666:666::66 pre R7(config)#$v6 pool ProbF 2666:666:666::6 2666:666:666::66 prefix-length ? <1-128> Prefix length R7(config)#$v6 pool ProbF 2666:666:666::6 2666:666:666::66 prefix-length 96 ? R7(config)#$v6 pool ProbF 2666:666:666::6 2666:666:666::66 prefix-length 96 R7(config)#ipv nat v6 R7(config)#ipv nat v6v4     4 R7(config)#ipv nat v4v6 sou R7(config)#ipv nat v4v6 source li R7(config)#ipv nat v4v6 source list 1 ? pool Specify pool name R7(config)#ipv nat v4v6 source list 1 po R7(config)#ipv nat v4v6 source list 1 pool ProbF ? R7(config)#ipv nat v4v6 source list 1 pool ProbF R7(config)#int fa 0/0 1 R7(config-if)#ipv nat R7(config-if)#int s 1/0.1 R7(config-subif)#int s 1/0.1pv nat  R7(config-subif)#^Z R7# *Mar 1 23:29:53.944: %SYS-5-CONFIG_I: Configured from console by console R7#sh ipv R7#sh ipv6 nat ? statistics Translation statistics translations Translation entries R7#sh ipv6 nat tra R7#sh ipv6 nat translations Prot IPv4 source IPv6 source IPv4 destination IPv6 destination --- 33.33.33.33 2005:0:237::3 --- --- R7# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6#ping 33.33.33.33 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 33.33.33.33, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 68/69/72 ms S6# S6# S6# S6#33.33.33.33 Trying 33.33.33.33 ... Open R3#q [Connection to 33.33.33.33 closed by foreign host] S6# S6# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#sh ipv nat % Incomplete command. R7#sh ipv nat tr Prot IPv4 source IPv6 source IPv4 destination IPv6 destination --- --- --- 180.40.7.2 2666:666:666::6 --- 33.33.33.33 2005:0:237::3 180.40.7.2 2666:666:666::6 --- 33.33.33.33 2005:0:237::3 --- --- R7# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#ping 22 666. :666:666::6 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2666:666:666::6, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/61/69 ms R3# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b 0/1 tunnel source FastEthernet0/1 tunnel mode ipv6ip 6to4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.1 255.255.255.224 duplex auto speed auto ipv6 nat ! interface Serial1/0 no ip address encapsulation frame-relay ! --More--  interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80::7 link-local ipv6 nat ipv6 ospf 1 area 0 frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::7/64 ipv6 ospf 1 area 0 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown --More--  ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router rip version 2 redistribute static metric 2 network 180.40.0.0 no auto-summary ! --More--  router bgp 100 no synchronization bgp router-id 7.7.7.7 bgp log-neighbor-changes neighbor 2000:3:3::3 remote-as 100 no neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: remote-as 200 neighbor 2002:B428:742:: ebgp-multihop 2 no neighbor 2002:B428:742:: activate no auto-summary ! address-family ipv6 neighbor 2000:3:3::3 activate neighbor 2002:B428:742:: activate neighbor 2002:B428:742:: route-map ProbD in network 2006:7:7::/128 exit-address-family ! ip classless ip route 33.33.33.0 255.255.255.0 Null0 ! ip as-path access-list 1 permit ^200$ no ip http server --More--  no ip http secure-server ! access-list 1 permit 180.40.7.2 access-list 1 permit 180.40.7.33 ipv6 route 2002::/16 Tunnel0 ipv6 router ospf 1 router-id 7.7.7.7 log-adjacency-changes distribute-list prefix-list ProbF out connected redistribute connected ! ipv6 router rip R7Rip ! ipv6 nat v4v6 source list 1 pool ProbF ipv6 nat v4v6 pool ProbF 2666:666:666::6 2666:666:666::66 prefix-length 96 ipv6 nat v6v4 source 2005:0:237::3 33.33.33.33 ipv6 nat prefix 2666:666:666::/96 ! ! ipv6 prefix-list ProbD seq 5 permit 2006:4:4::/128 ! ipv6 prefix-list ProbF seq 5 permit 2666:666:666::/96 route-map ProbD permit 10 --More--   match ipv6 address prefix-list ProbD set local-preference 90 ! route-map ProbD permit 20 match as-path 1 set as-path prepend 200 200 200 200 200 ! route-map ProbD permit 30 ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 --More--   R7#