=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.08.22 08:54:47 =~=~=~=~=~=~=~=~=~=~=~= config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip pim bi R7(config)#ip pim bidir-enable ? R7(config)#ip pim bidir-enable R7(config)# R7# *Mar 1 18:00:39.224: %SYS-5-CONFIG_I: Configured from console by console R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pim bidir-enable R1(config)#^Z R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#conf gt ^ % Invalid input detected at '^' marker. R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim bidir-enable R2(config)# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip pim bidir-enable R4(config)# RACK12AS>5 [Resuming connection 5 to r5 ... ] S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip pim bidir-enable S5(config)#^Z S5# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6#confi gt ^ % Invalid input detected at '^' marker. S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim bidir-enable S6(config)# S6(config)#^Z S6# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pim bidir-enable R3(config)#ip    do sh riun     un | b rp= -ca ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 ip pim register-rate-limit 2 ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 102 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! --More--   R3(config)#ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 ? bidir Group range treated in bidirectional shared-tree mode priority RP candidate priority R3(config)#ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 RACK12AS>1 [Resuming connection 1 to r1 ... ] *Mar R1#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 12:04:28, expires: 00:03:07 R1#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 12:25:45/00:02:14, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 12:24:16/00:00:00 Serial0/0.2, Forward/Sparse-Dense, 12:25:45/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 12:25:45/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 12:25:45/00:00:00 R1#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 124 ms Reply to request 0 from 180.40.7.130, 140 ms R1#ping 224.4.4.4sh ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:03/stopped, RP 180.40.7.129, flags: SP Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null (17.100.1.1, 224.4.4.4), 00:00:03/00:03:26, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:00:03/00:03:26 (*, 224.0.1.40), 12:26:01/00:02:50, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 12:24:32/00:00:00 Serial0/0.2, Forward/Sparse-Dense, 12:26:01/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 12:26:01/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 12:26:01/00:00:00 R1# RACK12AS>3 [Resuming connection 3 to r3 ... ] bi R3(config)#ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 bidir R3(config)# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip mrouteping 224.4.4.4sh ip mroute pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 12:05:19, expires: 00:03:19 R1#sh ip pim rp mapmroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 12:26:34/00:02:46, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 12:25:05/00:00:00 Serial0/0.2, Forward/Sparse-Dense, 12:26:34/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 12:26:34/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 12:26:34/00:00:00 R1#sh ip mroutepim rp mapmroute ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 116 ms Reply to request 0 from 180.40.7.130, 196 ms Reply to request 0 from 180.40.7.130, 172 ms R1#ping 224.4.4.4sh ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 12:26:43/00:02:58, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 12:25:14/00:00:00 Serial0/0.2, Forward/Sparse-Dense, 12:26:43/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 12:26:43/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 12:26:43/00:00:00 R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2(config)#sh    ^Z R2#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:10/00:02:55, RP 180.40.7.129, flags: BP Bidir-Upstream: Serial1/0.1, RPF nbr 180.40.7.33 Outgoing interface list: Serial1/0.1, Bidir-Upstream/Sparse-Dense, 00:00:10/00:00:00 (*, 224.6.6.6), 00:00:30/00:02:30, RP 180.40.7.129, flags: BC Bidir-Upstream: Serial1/0.1, RPF nbr 180.40.7.33 Outgoing interface list: *Mar 1 18:03:26.106: %SYS-5-CONFIG_I: Configured from console by console FastEthernet0/1, Forward/Sparse-Dense, 00:00:30/00:02:30 Serial1/0.1, Bidir-Upstream/Sparse-Dense, 00:00:31/00:00:00 (*, 224.0.1.40), 12:53:59/00:02:28, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 12:53:59/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 12:53:59/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 12:53:59/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 12:53:59/00:00:00 --More--   R2# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4(config)#do sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:58/00:02:33, RP 180.40.7.129, flags: BPL Bidir-Upstream: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: FastEthernet0/0, Bidir-Upstream/Dense, 00:00:58/00:00:00 (*, 224.0.1.40), 13:28:34/00:02:36, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 13:11:34/00:00:00 R4(config)#do sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 12:06:41, expires: 00:02:58 R4(config)# RACK12AS>3 [Resuming connection 3 to r3 ... ] *M R3(config)#ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 bidir   RACK12AS>7 [Resuming connection 7 to r7 ... ] \ % Unknown command or computer name, or unable to find computer address R7#confi gt ^ % Invalid input detected at '^' marker. R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip pim bidir-enable nip pim bidir-enable oip pim bidir-enable  ip pim bidir-enable  R7(config)#^Z R7#s *Mar 1 18:06:41.438: %SYS-5-CONFIG_I: Configured from console by console R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 12:09:08, expires: 00:02:29 R7#cela      clea ip pim rp R7#clea ip pim rpsh ip pim rp map PIM Group-to-RP Mappings R7#sh ip pim rp map PIM Group-to-RP Mappings R7#sh ip pim rp map PIM Group-to-RP Mappings R7#sh ip pim rp map PIM Group-to-RP Mappings R7#sh ip pim rp mapclea ip pim rp  R7#clea ip pim rp R7#clea ip pim rp clea ip pim rpsh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:01, expires: 00:03:28 R7#ping 244  24.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pim bidir-enablenip pim bidir-enableoip pim bidir-enable ip pim bidir-enable R1(config)#^Z R1#clea ip *Mar 1 18:10:06.194: %SYS-5-CONFIG_I: Configured from console by console R1#clea ip pim rp R1#sh ip pim rp map PIM Group-to-RP Mappings R1#~ sh ip pim rp map PIM Group-to-RP Mappings R1#sh ip pim rp map PIM Group-to-RP Mappings R1#sh ip pim rp map PIM Group-to-RP Mappings R1#sh ip pim rp map PIM Group-to-RP Mappings R1#sh ip pim rp map PIM Group-to-RP Mappings R1#sh ip pim rp map PIM Group-to-RP Mappings R1#sh ip pim rp mapclea ip pim rp  R1#clea ip pim rpsh ip pim rp map PIM Group-to-RP Mappings R1#sh ip pim rp map PIM Group-to-RP Mappings R1#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:00, expires: 00:03:29 R1# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#confrig Translating "confrig" Translating "confrig" % Unknown command or computer name, or unable to find computer address R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#no ip pim bidir-enable no ip pim bidir-enable  ip pim bidir-enable  R7(config)#^Z R7#^x1 % Unknown command or computer name, or unable to find computer address R7# *Mar 1 18:10:25.080: %SYS-5-CONFIG_I: Configured from console by console R7# R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#no ip pim bidir-enableno ip pim bidir-enable ip pim bidir-enable ip pim bidir-enable  R1(config)# R1# *Mar 1 18:11:38.497: %SYS-5-CONFIG_I: Configured from console by console R1# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3(config)#ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 bidir R3# *Mar 1 18:11:11.757: %SYS-5-CONFIG_I: Configured from console by console R3# RACK12AS>6 [Resuming connection 6 to r6 ... ] 18 S6# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip dhc R2(config)#ip dhcp P ? aaa Configure aaa attributes binding DHCP address bindings bootp BOOTP specific configuration conflict DHCP address conflict parameters database Configure DHCP database agents excluded-address Prevent DHCP from assigning certain addresses limited-broadcast-address Use all 1's broadcast address ping Specify ping parameters used by DHCP pool Configure DHCP address pools relay DHCP relay agent parameters smart-relay Enable Smart Relay feature R2(config)#ip dhcp pool ? WORD Pool name R2(config)#ip dhcp pool Prob13 R2(dhcp-config)#net R2(dhcp-config)#net? netbios-name-server netbios-node-type network R2(dhcp-config)#netw R2(dhcp-config)#network ? A.B.C.D Network number in dotted-decimal notation R2(dhcp-config)#network 180.40.7.96 ? /nn or A.B.C.D Network mask or prefix length R2(dhcp-config)#network 180.40.7.96 /27 R2(dhcp-config)#exit R2(config)#ip dhcp ex R2(config)#ip dhcp excluded-address 180.40.7.98 R2(config)#^Z R2# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6#deb ip dhc S6#deb ip dhcp ? server DHCP server activity snooping DHCP Snooping S6#deb ip dhcp         dhc S6#deb dhcp ? detail DHCP packet content S6#deb dhcp de S6#deb dhcp detail DHCP client activity debugging is on (detailed) S6#CONFIG T Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/2 S6(config-if)#ip add dh S6(config-if)#ip add dhcp S6(config-if)# 18:24:25: DHCP: DHCP client process started: 10 18:24:25: RAC: Starting DHCP discover on FastEthernet0/2 18:24:25: DHCP: Try 1 to acquire address for FastEthernet0/2 18:24:25: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/2 from FULL to DOWN, Neighbor Down: Interface down or detached 18:24:30: DHCP: allocate request 18:24:30: DHCP: new entry. add to queue 18:24:30: DHCP: SDiscover attempt # 1 for entry: 18:24:30: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/2 18:24:30: Temp sub net mask: 0.0.0.0 18:24:30: DHCP Lease server: 0.0.0.0, state: 1 Selecting 18:24:30: DHCP transaction id: 264 18:24:30: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs 18:24:30: Next timer fires after: 00:00:03 18:24:30: Retry count: 1 Client-ID: cisco-0011.9212.de00-Fa0/2 18:24:30: Hostname: S6 18:24:30: DHCP: SDiscover: sending 294 byte length DHCP packet 18:24:30: DHCP: SDiscover 294 bytes 18:24:30: B'cast on FastEthernet0/2 interface from 0.0.0.0 18:24:32: DHCP: Received a BOOTREP pkt 18:24:32: DHCP: Scan: Message type: DHCP Offer 18:24:32: DHCP: Scan: Server ID Option: 180.40.7.98 = B4280762 18:24:32: DHCP: Scan: Lease Time: 86400 18:24:32: DHCP: Scan: Renewal time: 43200 18:24:32: DHCP: Scan: Rebind time: 75600 18:24:32: DHCP: Scan: Subnet Address Option: 255.255.255.224 18:24:32: DHCP: rcvd pkt source: 180.40.7.98, destination: 255.255.255.255 18:24:32: UDP sport: 43, dport: 44, length: 308 18:24:32: DHCP op: 2, htype: 1, hlen: 6, hops: 0 18:24:32: DHCP server identifier: 180.40.7.98 18:24:32: xid: 264, secs: 0, flags: 8000 18:24:32: client: 0.0.0.0, your: 180.40.7.97 18:24:32: srvr: 0.0.0.0, gw: 0.0.0.0 18:24:32: options block length: 60 18:24:32: DHCP Offer Message Offered Address: 180.40.7.97 18:24:32: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 18:24:32: DHCP: Server ID Option: 180.40.7.98 18:24:32: DHCP: offer received from 180.40.7.98 18:24:32: DHCP: SRequest attempt # 1 for entry: 18:24:32: Temp IP addr: 180.40.7.97 for peer on Interface: FastEthernet0/2 18:24:32: Temp sub net mask: 255.255.255.224 18:24:32: DHCP Lease server: 180.40.7.98, state: 2 Requesting 18:24:32: DHCP transaction id: 264 18:24:32: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs 18:24:32: Next timer fires after: 00:00:02 18:24:32: Retry count: 1 Client-ID: cisco-0011.9212.de00-Fa0/2 18:24:32: Hostname: S6 18:24:32: DHCP: SRequest- Interface FastEthernet0/2 assigned DHCP address 180.40.7.97, mask 255.255.255.224 Server ID option: 180.40.7.98 18:24:32: DHCP: SRequest- Requested IP addr option: 180.40.7.97 18:24:32: DHCP: SRequest placed lease len option: 86400 18:24:32: DHCP: SRequest: 312 bytes 18:24:32: DHCP: SRequest: 312 bytes 18:24:32: B'cast on FastEthernet0/2 interface from 0.0.0.0 18:24:32: DHCP: Received a BOOTREP pkt 18:24:32: DHCP: Scan: Message type: DHCP Ack 18:24:32: DHCP: Scan: Server ID Option: 180.40.7.98 = B4280762 18:24:32: DHCP: Scan: Lease Time: 86400 18:24:32: DHCP: Scan: Renewal time: 43200 18:24:32: DHCP: Scan: Rebind time: 75600 18:24:32: DHCP: Scan: Subnet Address Option: 255.255.255.224 18:24:32: DHCP: rcvd pkt source: 180.40.7.98, destination: 255.255.255.255 18:24:32: UDP sport: 43, dport: 44, length: 308 18:24:32: DHCP op: 2, htype: 1, hlen: 6, hops: 0 18:24:32: DHCP server identifier: 180.40.7.98 18:24:32: xid: 264, secs: 0, flags: 8000 18:24:32: client: 0.0.0.0, your: 180.40.7.97 18:24:32: srvr: 0.0.0.0, gw: 0.0.0.0 18:24:32: options block length: 60 18:24:32: DHCP Ack Message 18:24:32: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 18:24:32: DHCP: Server ID Option: 180.40.7.98 18:24:35: DHCP: Releasing ipl options: 18:24:35: DHCP: Applying DHCP options: 18:24:35: DHCP Client Pooling: ***Allocated IP address: 180.40.7.97 18:24:35: Allocated IP address = 180.40.7.97 255.255.255.224 18:24:45: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/2 from LOADING to FULL, Loading Done S6(config-if)# RACK12AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh ip dhcp bi Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.97 0063.6973.636f.2d30. Mar 02 1993 06:21 PM Automatic 3031.312e.3932.3132. 2e64.6530.302d.4661. 302f.32 R2# *Mar 1 18:23:01.444: %PIM-5-NBRCHG: neighbor 0.0.0.0 DOWN on interface FastEthernet0/1 (vrf default) non DR R2# R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#no ip dhcp pool Prob13 R2(config)#no ip dhcp pool Prob13no ip dhcp pool Prob13  ip dhcp pool Prob13  R2(dhcp-config)#cli R2(dhcp-config)#client-i R2(dhcp-config)#client-identifier 0063.6973.636f.2d30.3031.312e.3932.3132.2e6$tifier 0063.6973.636f.2d30.3031.312e.3932.3132.2e64 .6530.3023.6973.636f.2d30.3031.312e.3932.3132.2e64.6530.302d .4661.302f.2d30.3031.312e.3932.3132.2e64.6530.302d.4661.302f .32 R2(dhcp-config)#host ? A.B.C.D IP address in dotted-decimal notation R2(dhcp-config)#host 1 180.l 40.7.97 ? /nn or A.B.C.D Network mask or prefix length R2(dhcp-config)#host 180.40.7.97 /27 R2(dhcp-config)#^Z R2# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6(config-if)#ip add 180.40.7.97 255.255.255.224 18:30:51: DHCP: SRelease attempt # 1 for entry: 18:30:51: Temp IP addr: 180.40.7.97 for peer on Interface: FastEthernet0/2 18:30:51: Temp sub net mask: 255.255.255.224 18:30:51: DHCP Lease server: 180.40.7.98, state: 7 Releasing 18:30:51: DHCP transaction id: 264 18:30:51: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs 18:30:51: Next timer fires after: 00:00:01 18:30:51: Retry count: 1 Client-ID: cisco-0011.9212.de00-Fa0/2 18:30:51: Hostname: S6 18:30:51: DHCP: SRelease placed Server ID option: 180.40.7.98 18:30:51: DHCP: SRelease: 279 bytes 18:30:51: DHCP: SRelease attempt # 2 for entry: 18:30:51: Temp IP addr: 180.40.7.97 for peer on Interface: FastEthernet0/2 18:30:51: Temp sub net mask: 255.255.255.224 18:30:51: DHCP Lease server: 180.40.7.98, state: 7 Releasing 18:30:51: DHCP transaction id: 264 18:30:51: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs 18:30:51: Next timer fires after: 00:00:00 18:30:51: Retry count: 2 S6(config-if)#^Z S6# Client-ID: cisco-0011.9212.de00-Fa0/2 18:30:51: Hostname: S6 18:30:51: DHCP: SRelease placed Server ID option: 180.40.7.98 18:30:51: DHCP: SRelease: 279 bytes 18:30:51: DHCP: Releasing ipl options: 18:30:52: DHCP: SRelease attempt # 3 for entry: 18:30:52: Temp IP addr: 180.40.7.97 for peer on Interface: FastEthernet0/2 18:30:52: Temp sub net mask: 255.255.255.224 18:30:52: DHCP Lease server: 180.40.7.98, state: 7 Releasing 18:30:52: DHCP transaction id: 264 18:30:52: Lease: 86400u secs, Renewal: 43200 secs, Rebind: 75600 secs 18:30:52: Next timer fires after: 00:00:01 18:30:52: Retry count: 3 Client-ID: cisco-0011.9212.de00-Fa0/2 18:30:52: Hostname: S6 18:30:52: DHCP: SRelease placed Server ID option: 180.40.7.98 18:30:52: DHCP: SRelease: 279 bytes 18:30:53: RAC: DHCP stopped on interface FastEthernet0/2 18:30:53: %SYS-5-CONFIG_I: Configured from console by console all All possible debugging has been turned off S6# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int fa 0/1 R2(config-if)# R2(config-if)#ip ? Interface IP configuration subcommands: access-group Specify access control for packets accounting Enable IP accounting on this interface address Set the IP address of an interface audit Apply IDS audit name auth-proxy Apply authentication proxy authentication authentication subcommands bandwidth-percent Set EIGRP bandwidth limit bgp BGP interface commands broadcast-address Set the broadcast address of an interface cef Cisco Express Forwarding interface commands cgmp Enable/disable CGMP dhcp Configure DHCP parameters for this interface directed-broadcast Enable forwarding of directed broadcasts dvmrp DVMRP interface commands flow NetFlow related commands hello-interval Configures IP-EIGRP hello interval helper-address Specify a destination address for UDP broadcasts hold-time Configures IP-EIGRP hold time idle-group Specify interesting packets for idle-timer igmp IGMP interface commands information-reply Enable sending ICMP Information Reply messages --More--   R2(config-if)#ip mu R2(config-if)#ip multicast ? boundary Boundary for administratively scoped multicast addresses helper-map Broadcast to Multicast map OR Multicast to ip-address map netflow NetFlow accounting for multicast rate-limit Rate limit multicast data packets tagswitch Enable IP Multicast Tagswitching ttl-threshold TTL threshold for multicast packets R2(config-if)#ip multicast hel R2(config-if)#ip multicast helper-map ? A.B.C.D IP multicast address broadcast Broadcast address R2(config-if)#ip multicast helper-map br R2(config-if)#ip multicast helper-map broadcast ? A.B.C.D IP address R2(config-if)#ip multicast helper-map broadcast 224.66.66 . 6.66 ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R2(config-if)#ip multicast helper-map broadcast 224.66.66.66                                                EXIT R2(config)#ip access R2(config)#ip access-list ex R2(config)#ip access-list extended Prob13 ? R2(config)#ip access-list extended Prob13 R2(config-ext-nacl)#per ho    udp host 180.40.7.97 host 255.23556    55.255.255 ? dscp Match packets with given dscp value eq Match only packets on a given port number fragments Check non-initial fragments gt Match only packets with a greater port number log Log matches against this entry log-input Log matches against this entry, including input interface lt Match only packets with a lower port number neq Match only packets not on a given port number precedence Match packets with given precedence value range Match only packets in the range of port numbers reflect Create reflexive access list entry time-range Specify a time-range tos Match packets with given TOS value R2(config-ext-nacl)#per udp host 180.40.7.97 host 255.255.255.255 eq tftp R2(config-ext-nacl)#int fa 0/1 R2(config-if)#ip mu h R2(config-if)#ip mu helper-map br R2(config-if)#ip mu helper-map broadcast 224.66.66.666  ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R2(config-if)#ip mu helper-map broadcast 224.66.66.66 Pr rob13 ? R2(config-if)#ip mu helper-map broadcast 224.66.66.66 Prob13 R2(config-if)#^Z R2# *Mar 1 18:35:07.302: %SYS-5-CONFIG_I: Configured from console by console R2# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int s 0/0.1 R1(config-subif)#shut R1(config-subif)# *Mar 1 18:36:13.936: %PIM-5-NBRCHG: neighbor 180.40.7.33 DOWN on interface Serial0/0.1 (vrf default) non DR R1(config-subif)#shut exit R1(config)#access-list iaccess-list paccess-list  access-list access-list ex Pro13  b13 R1(config-ext-nacl)#per ip host 180.40.7.97 host 224.66.66.66 R1(config-ext-nacl)#int s 0/0.2 R1(config-subif)#ip mu h R1(config-subif)#ip mu helper-map ? A.B.C.D IP multicast address broadcast Broadcast address R1(config-subif)#ip mu helper-map 224.66.66.66 17.100.1.255 ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R1(config-subif)#ip mu helper-map 224.66.66.66 17.100.1.255 Prob13 R1(config-subif)# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#deb ip pack           config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#logg bugg Translating "bugg" ^ % Invalid input detected at '^' marker. R7(config)#logg bugg  ff R7(config)#^Z R7#deb ip pa *Mar 1 18:38:50.372: %SYS-5-CONFIG_I: Configured from console by console R7#deb ip pack IP packet debugging is on R7#deb ip pack *Mar 1 18:38:53.661: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.1, len 28, rcvd 0 R7#deb ip pack de IP packet debugging is on (detailed) R7# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6#coip ~  py tftp run Address or name of remote host []? 255.255.255.255.  Source filename []? test Destination filename [running-config]? Accessing tftp://255.255.255.255/test... RACK12AS>7 [Resuming connection 7 to r7 ... ] *Ma R7# *Mar 1 18:39:17.204: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 18:39:17.801: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 R7# *Mar 1 18:39:19.159: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 18:39:22.805: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 R7# *Mar 1 18:39:25.461: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 R7# *Mar 1 18:39:27.216: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 18:39:27.813: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 R7# *Mar 1 18:39:29.160: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1(config-subif)#int e 0/1 R1(config-if)#ip di R1(config-if)#ip directed-broadcast R1(config-if)#^Z R1# RACK12AS>7 [Resuming connection 7 to r7 ... ] *M R7# RACK12AS>6 [Resuming connection 6 to r6 ... ] RACK12AS>7 [Resuming connection 7 to r7 ... ] *Mar R7# *Mar 1 18:39:50.611: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 58, rcvd 0, proto=103 R7# *Mar 1 18:39:52.069: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 56, rcvd 0, proto=103 R7#sh *Mar 1 18:39:55.262: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 R7#sh log Syslog logging: enabled (9 messages dropped, 3 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 144 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 88 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 64 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 18:38:50.372: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 18:38:53.661: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.1, len 28, rcvd 0 *Mar 1 18:38:55.705: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.1.40, len 28, rcvd 0 *Mar 1 18:38:55.713: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast *Mar 1 18:38:57.175: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 18:38:57.640: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 *Mar 1 18:38:59.158: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 *Mar 1 18:39:02.704: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 *Mar 1 18:39:07.208: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, le *Mar 1 18:39:57.218: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89n 80, rcvd 0, proto=89 *Mar 1 18:39:07.712: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 *Mar 1 18:39:09.159: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 --More--  *Mar 1 18:39:12.721: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 *Mar 1 18:39:17.204: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 18:39:17.801: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 *Mar 1 18:39:19.159: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 *Mar 1 18:39:22.805: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 *Mar 1 18:39:25.461: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 *Mar 1 18:39:27.216: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, *Mar 1 18:39:59.161: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 rcvd 0, proto=89 *Mar 1 18:39:27.813: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 *Mar 1 18:39:29.160: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 *Mar 1 18:39:37.217: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 18:39:39.160: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 *Mar 1 18:39:43.587: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 41, rcvd 2 --More--  *Mar 1 18:39:43.587: UDP src=53290, dst=69 *Mar 1 18:39:47.217: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 18:39:49.160: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 *Mar 1 18:39:50.611: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 58, rcvd 0, proto=103 *Mar 1 18:39:52.069: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 56, rcvd 0, proto=103 *Mar 1 18:39:55.262: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 *Mar 1 18:39:57.218: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# *Mar 1 18:40:07.218: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# *Mar 1 18:40:09.161: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 18:40:17.222: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# *Mar 1 18:40:19.161: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 18:40:24.150: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.1, len 28, rcvd 0, proto=2 *Mar 1 18:40:25.127: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 R7# *Mar 1 18:40:27.247: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 18:40:28.116: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 40, rcvd 0, proto=103 R7# RACK12AS>6 [Resuming connection 6 to r6 ... ] % S6#test255.255.255.255test   S6# S6# RACK12AS>1 [Resuming connection 1 to r1 ... ] * R1#sh ip int e 0/1 Ethernet0/1 is up, line protocol is up Internet address is 17.100.1.1/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is enabled Multicast reserved groups joined: 224.0.0.5 224.0.0.6 224.0.0.1 224.0.0.2 224.0.0.22 224.0.0.13 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF Fast switching turbo vector --More--   R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ip bro R1(config-if)#ip broadcast-address 17.100.1.255 R1(config-if)#^Z R1# RACK12AS>6 [Resuming connection 6 to r6 ... ] test255.255.255.255copy tftp run  Address or name of remote host [255.255.255.255]? Source filename [test]? Destination filename [running-config]? Accessing tftp://255.255.255.255/test... RACK12AS>7 [Resuming connection 7 to r7 ... ] *Ma R7# R7# R7# R7# R7# R7# *Mar 1 18:41:47.262: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 18:41:47.566: IP: tableid=0, s=180.40.7.97 (FastEthernet0/1), d=17.100.1.255 (FastEthernet0/1), routed via RIB *Mar 1 18:41:47.566: IP: s=180.40.7.97 (FastEthernet0/1), d=17.100.1.255 (FastEthernet0/1), len 41, rcvd 3 *Mar 1 18:41:47.566: UDP src=52997, dst=69 R7# *Mar 1 18:41:49.165: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 18:41:52.254: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 56, rcvd 0, proto=103 *Mar 1 18:41:52.567: IP: tableid=0, s=180.40.7.97 (FastEthernet0/1), d=17.100.1.255 (FastEthernet0/1), routed via RIB *Mar 1 18:41:52.567: IP: s=180.40.7.97 (FastEthernet0/1), d=17.100.1.255 (FastEthernet0/1), len 41, rcvd 3 *Mar 1 18:41:52.567: UDP src=52997, dst=69 R7# *Mar 1 18:41:53.284: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 R7# *Mar 1 18:41:54.526: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.1, len 28, rcvd 0, proto=2 R7# *Mar 1 18:41:57.266: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# *Mar 1 18:41:58.564: IP: tableid=0, s=180.40.7.97 (FastEthernet0/1), d=17.100.1.255 (FastEthernet0/1), routed via RIB *Mar 1 18:41:58.564: IP: s=180.40.7.97 (FastEthernet0/1), d=17.100.1.255 (FastEthernet0/1), len 41, rcvd 3 *Mar 1 18:41:58.564: UDP src=52997, dst=69 *Mar 1 18:41:59.165: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 18:42:02.539: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.1.40, len 28, rcvd 0, proto=2 R7#u a *Mar 1 18:42:05.600: IP: tableid=0, s=180.40.7.97 (FastEthernet0/1), d=17.100.1.255 (FastEthernet0/1), routed via RIB *Mar 1 18:42:05.600: IP: s=180.40.7.97 (FastEthernet0/1), d=17.100.1.255 (FastEthernet0/1), len 41, rcvd 3 *Mar 1 18:42:05.600: UDP src=52997, dst=69 R7#u all All possible debugging has been turned off R7# R7# *Mar 1 18:42:07.267: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# RACK12AS>1 [Resuming connection 1 to r1 ... ] *Mar 1 18:42:37.657: %SYS-5-CONFIG_I: R1#sh run | b 0/0 interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip multicast rate-limit in group-list 2 video 80 ip igmp access-group 1 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point shutdown frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map 224.66.66.66 17.100.1.255 Prob13 ip ospf network point-to-multipoint --More--   frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip broadcast-address 17.100.1.255 ip directed-broadcast ip pim query-interval 90 ip pim sparse-dense-mode ip igmp query-interval 90 half-duplex no keepalive ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! --More--  ip pim bidir-enable ip pim spt-threshold 1 ! ! ip access-list extended Prob13 permit ip host 180.40.7.97 host 224.66.66.66 access-list 1 deny 224.20.73.1 15.128.20.0 access-list 1 permit any access-list 2 permit 239.0.0.0 0.255.255.255 ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! --More--   R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b 0/1 interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 224.66.66.66 Prob13 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint --More--   R2#sh run | b 0/1     dhcp ip dhcp excluded-address 180.40.7.98 ! ip dhcp pool Prob13 host 180.40.7.97 255.255.255.224 client-identifier 0063.6973.636f.2d30.3031.312e.3932.3132.2e64.6530.302d.4661.302f.32 ! ip cef no ip domain lookup ip multicast-routing ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! --More--  ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 224.66.66.66 Prob13 duplex auto --More--   speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown --More--  ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 --More--   no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ! ip access-list extended Prob13 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! ! --More--   R2#sh ip p ospf Routing Process "ospf 1" with ID 180.40.7.98 Supports only single TOS(TOS0) routes Supports opaque LSA Supports Link-local Signaling (LLS) Initial SPF schedule delay 5000 msecs Minimum hold time between two consecutive SPFs 10000 msecs Maximum wait time between two consecutive SPFs 10000 msecs Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs LSA group pacing timer 240 secs Interface flood pacing timer 33 msecs Retransmission pacing timer 66 msecs Number of external LSA 0. Checksum Sum 0x000000 Number of opaque AS LSA 0. Checksum Sum 0x000000 Number of DCbitless external and opaque AS LSA 0 Number of DoNotAge external and opaque AS LSA 0 Number of areas in this router is 1. 1 normal 0 stub 0 nssa External flood list length 0 Area BACKBONE(0) Number of interfaces in this area is 4 Area has no authentication SPF algorithm last executed 00:09:10.074 ago SPF algorithm executed 13 times Area ranges are --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router psp   ospf 1 R2(config-router)#route R2(config-router)#router-id 2.2.2.2 Reload or use "clear ip ospf process" command, for this to take effect R2(config-router)#^Z R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] * R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router ospf 1 R3(config-router)#rout R3(config-router)#router-id 3.3.3.3 Reload or use "clear ip ospf process" command, for this to take effect R3(config-router)#in  do sj   h ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES manual administratively down down BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.129 YES manual up up Serial1/0 180.40.7.33 YES manual up up Serial1/1 unassigned YES manual administratively down down Serial1/2 180.40.7.3 YES manual up up Serial1/3 unassigned YES manual administratively down down Serial1/4 unassigned YES manual administratively down down Serial1/5 unassigned YES manual administratively down down --More--  Serial1/6 unassigned YES manual administratively down down Serial1/7 unassigned YES manual administratively down down R3(config-router)#int lo 0 R3(config-if)#ip address 223.254.254.254 255.255.255.255 R3(config-if)#^Z R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int lo 0 R2(config-if)#int lo 0 R2(config-if)#exit R2(config)#ip ms R2(config)#ip msdp ? cache-rejected-sa Store rejected SAs from all peers default-peer Default MSDP peer to accept SA messages from description Peer specific description filter-sa-request Filter SA-Requests from peer keepalive Configure keepalive parameters for a peer mesh-group Configure an MSDP mesh-group originator-id Configure MSDP Originator ID peer Configure an MSDP peer redistribute Inject multicast route entries into MSDP sa-filter Filter SA messages from peer sa-limit Configure SA limit for a peer shutdown Administratively shutdown MSDP peer timer MSDP timer ttl-threshold Configure TTL Threshold for MSDP Peer vrf Select VPN Routing/Forwarding instance R2(config)#ip msdp peer ? Hostname or A.B.C.D Peer name or address R2(config)#ip msdp peer 180.40.7.129 ? connect-source Configure source address used for MSDP connection remote-as Configured AS number R2(config)#ip msdp peer 180.40.7.129 con R2(config)#ip msdp peer 180.40.7.129 connect-source ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config)#ip msdp peer 180.40.7.129 connect-source fa 0/1 R2(config)# RACK12AS>3 [Resuming connection 3 to r3 ... ] * R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip msp R3(config)#ip msp  R3(config)#ip msdp p R3(config)#ip msdp peer 180.40.7.98 con R3(config)#ip msdp peer 180.40.7.98 connect-source fa 0/1 R3(config)#do sh ip msp peer sh ip msp peer ^ % Invalid input detected at '^' marker. R3(config)#do sh ip msp peer do sh ip msp peerdp peer MSDP Peer 180.40.7.98 (?), AS ? Connection status: State: Listen, Resets: 0, Connection source: FastEthernet0/1 (180.40.7.129) Uptime(Downtime): 00:00:12, Messages sent/received: 0/0 Output messages discarded: 0 Connection and counters cleared 00:00:12 ago SA Filtering: Input (S,G) filter: none, route-map: none Input RP filter: none, route-map: none Output (S,G) filter: none, route-map: none Output RP filter: none, route-map: none SA-Requests: Input filter: none Peer ttl threshold: 0 SAs learned from this peer: 0 Input queue size: 0, Output queue size: 0 R3(config)# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#p  RACK12AS>2 [Resuming connection 2 to r2 ... ] *Mar R2(config)#ip pimkj     rp-ca R2(config)#ip pim rp-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config)#ip pim rp-candidate fa    lo 1                        do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES manual administratively down down BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.98 YES manual up up Serial1/0 unassigned YES manual up up Serial1/0.1 180.40.7.35 YES manual up up Serial1/0.2 180.40.7.65 YES manual up up Serial1/1 unassigned YES manual administratively down down Serial1/2 180.40.7.2 YES manual up up Serial1/3 unassigned YES manual administratively down down --More--  Serial1/4 unassigned YES manual administratively down down Serial1/5 unassigned YES manual administratively down down Serial1/6 unassigned YES manual administratively down down Serial1/7 unassigned YES manual administratively down down Loopback0 unassigned YES unset up up R2(config)#int lo 0 R2(config-if)#ip address 223.254.254.254 255.255.255.255 R2(config-if)#exit R2(config)#exitip address 223.254.254.254 255.255.255.255 ^ % Invalid input detected at '^' marker. R2(config)#ip address 223.254.254.254 255.255.255.255exit ip address 223.254.254.254 255.255.255.255nt lo 0 do sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES manual administratively down down BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.98 YES manual up up Serial1/0 unassigned YES manual up up Serial1/0.1 180.40.7.35 YES manual up up Serial1/0.2 180.40.7.65 YES manual up up Serial1/1 unassigned YES manual administratively down down Serial1/2 180.40.7.2 YES manual up up Serial1/3 unassigned YES manual administratively down down --More--  Serial1/4 unassigned YES manual administratively down down Serial1/5 unassigned YES manual administratively down down Serial1/6 unassigned YES manual administratively down down Serial1/7 unassigned YES manual administratively down down Loopback0 223.254.254.254 YES manual up up R2(config)#ip pim rp-cam n R2(config)#ip pim rp-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config)#ip pim rp-candidate lo 0 ? bidir Group range treated in bidirectional shared-tree mode group-list group-list interval RP candidate advertisement interval priority RP candidate priority R2(config)#ip pim rp-candidate lo 0 in R2(config)#ip pim rp-candidate lo 0 interval 5 ? bidir Group range treated in bidirectional shared-tree mode priority RP candidate priority R2(config)#ip pim rp-candidate lo 0 interval 5 bi R2(config)#ip pim rp-candidate lo 0 interval 5 bidir Warning: PIMv2 not configured on Loopback0, Candidate-RP not advertised R2(config)#int lo 0 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#ip pim sparse-dense-mode nt lo 0 p pim rp-candidate lo 0 interval 5 bidir *Mar 1 18:48:59.446: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback0 (vrf default) R2(config-if)#ip pim rp-candidate lo 0 interval 5 bidir R2(config)#^Z R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] *M R3(config)#do sh run | i ip pi     rp-ca ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 bidir R3(config)#no ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 bid$p-candidate FastEthernet0/1 group-list 1 interval 5 bidi r R3(config)#$p-candidate FastEthernet0/1 group-list 1 interval 5 bidir int lo 0 R3(config-if)#ip pim sp R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)#exit R3(config)# *Mar 1 18:49:29.808: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback0 (vrf default) R3(config)#exitip pim sparse-dense-mode nt lo 0 $p-candidate FastEthernet0/1 group-list 1 interval 5 bidir group-list 1 interval 5 bidir  group-list 1 interval 5 bidir t0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir 0 group-list 1 interval 5 bidir l0 group-list 1 interval 5 bidiro0 group-list 1 interval 5 bidirno ip pim rp-candidate lo0 group-list 1 interval 5 bidirno ip pim rp-candidate lo0 group-list 1 interval 5 bidir  ip pim rp-candidate lo0 group-list 1 interval 5 bidir  R3(config)#^Z R3# RACK12AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:52, expires: 00:02:55 R1#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 133 ms R1#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets C 17.57.100.0 is directly connected, Ethernet0/0 C 17.100.1.0 is directly connected, Ethernet0/1 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/65] via 180.40.7.65, 00:03:33, Serial0/0.2 O 192.10.32.0/24 [110/847] via 180.40.7.65, 00:03:33, Serial0/0.2 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.128/27 [110/846] via 180.40.7.65, 00:03:33, Serial0/0.2 O 180.40.7.0/27 [110/845] via 180.40.7.65, 00:03:34, Serial0/0.2 O 180.40.7.35/32 [110/64] via 180.40.7.65, 00:03:34, Serial0/0.2 O 180.40.7.33/32 [110/845] via 180.40.7.65, 00:03:34, Serial0/0.2 O 180.40.7.65/32 [110/64] via 180.40.7.65, 00:03:34, Serial0/0.2 C 180.40.7.64/27 is directly connected, Serial0/0.2 --More--   R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] *M R2#clea ip ospf pro Reset ALL OSPF processes? [no]: y R2# R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] *M R3# *Mar 1 18:54:30.757: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial1/2 from FULL to DOWN, Neighbor Down: Adjacency forced to reset R3#clea ip ospf pro Reset ALL OSPF processes? [no]: y R3# R3# *Mar 1 18:54:37.416: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/2 from INIT to DOWN, Neighbor Down: Interface down or detached *Mar 1 18:54:37.416: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from INIT to DOWN, Neighbor Down: Interface down or detached *Mar 1 18:54:37.416: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial1/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 18:54:37.416: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.12 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 18:54:37.573: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.12 on FastEthernet0/1 from LOADING to FULL, Loading Done R3# *Mar 1 18:54:40.918: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/2 from LOADING to FULL, Loading Done R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip pim bi R3(config)#no ip pim bidir-enable *Mar 1 18:54:55.390: %MSDP-5-PEER_UPDOWN: Session to peer 180.40.7.98 going down R3(config)#no ip pim bidir-enable *Mar 1 18:55:01.051: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/0 from LOADING to FULL, Loading Done R3(config)#no ip pim bidir-enable R3(config)#do hsh   sh i rui n | i ip pim rp-can R3(config)#do sh run | i ip pim rp-canno ip pim bidir-enable  ip pim rp-candidate lo0 group-list 1 interval 5 bidir~        R3(config)#^Z R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Mar R2# *Mar 1 18:55:59.419: %MSDP-5-PEER_UPDOWN: Session to peer 180.40.7.129 going up R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim rp-candidate lo 0 interval 5 bidir        R2(config)#do sh run | b i rp-can ip pim rp-candidate Loopback0 interval 5 R2(config)#^Z R2# *Mar 1 18:56:19.969: %SYS-5-CONFIG_I: Configured from RACK12AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:07:25, expires: 00:03:05 R1#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: *Mar 1 18:57:26.177: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial0/0.2 from FULL to DOWN, Neighbor Down: Dead timer expired Reply to request 0 from 180.40.7.97, 92 ms Reply to request 0 from 180.40.7.97, 104 ms R1#ping 224.6.6.6sh ip pim rp maproute ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 144 ms R1# RACK12AS>2 [Resuming connection 2 to r2 ... ] e by console R2# R2#sh ip mspd    p dp sa R2#sh ip msdp sa-cache MSDP Source-Active Cache - 0 entries R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip ms R3#sh ip msdp as  SA R3#sh ip msdp SA-cache MSDP Source-Active Cache - 2 entries (17.100.1.1, 224.4.4.4), RP 223.254.254.254, AS ?,00:00:27/00:05:44, Peer 180.40.7.98 (17.100.1.1, 224.6.6.6), RP 223.254.254.254, AS ?,00:00:35/00:05:44, Peer 180.40.7.98 R3# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#ip igm R7(config-if)#ip igmp jo R7(config-if)#ip igmp join-group 224.7.7.7.  R7(config-if)#^Z R7#^x4 % Unknown command or computer name, or unable to find computer address R7# R7# *Mar 1 19:00:48.681: %SYS-5-CONFIG_I: Configured from console by console R7# RACK12AS>4 [Resuming connection 4 to r4 ... ] * R4(config)#exut    int fa 0/0 R4(config-if)#ip pim sp R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)#^Z R4#ping *Mar 1 19:03:36.715: %SYS-5-CONFIG_I: Configured from console by console R4#ping 224.7.7.7.7   Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 116 ms R4# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip msdp SA-cache config t sh ip msdp SA-cache MSDP Source-Active Cache - 2 entries (17.100.1.1, 224.4.4.4), RP 223.254.254.254, AS ?,00:04:37/00:03:33, Peer 180.40.7.98 (17.100.1.1, 224.6.6.6), RP 223.254.254.254, AS ?,00:04:45/00:03:33, Peer 180.40.7.98 R3# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip msdp sa-cache MSDP Source-Active Cache - 1 entries (180.40.7.130, 224.7.7.7), RP 223.254.254.254, AS ?,00:00:11/00:05:48, Peer 180.40.7.129 R2#ash     sh run | b Lo interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 224.66.66.66 Prob13 duplex auto speed auto ! interface Serial1/0 no ip address --More--   encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode --More--   clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 --More--   router-id 2.2.2.2 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 5 ip msdp peer 180.40.7.129 connect-source FastEthernet0/1 ! ip access-list extended Prob13 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! ! ! --More--   R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b Lo interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim dense-mode proxy-register list 102 duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.33 255.255.255.224 ip pim sparse-dense-mode --More--   encapsulation frame-relay ip ospf network point-to-multipoint frame-relay map ip 180.40.7.34 301 broadcast frame-relay map ip 180.40.7.35 302 broadcast no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip pim sparse-dense-mode ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 --More--   no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim spt-threshold 1 ip pim rp-candidate Loopback0 group-list 1 interval 5 ip pim register-rate-limit 2 --More--  ip msdp peer 180.40.7.98 connect-source FastEthernet0/1 ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 102 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! --More--   R3#sh run Building configuration... Current configuration : 1939 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R3 ! boot-start-marker boot-end-marker ! ! no network-clock-participate slot 1 no network-clock-participate wic 0 no aaa new-model ip subnet-zero ! ! ! ip cef no ip domain lookup --More--  ip multicast-routing ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 --More--   ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim dense-mode proxy-register list 102 duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.33 255.255.255.224 ip pim sparse-dense-mode encapsulation frame-relay --More--   ip ospf network point-to-multipoint frame-relay map ip 180.40.7.34 301 broadcast frame-relay map ip 180.40.7.35 302 broadcast no frame-relay inverse-arp ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip pim sparse-dense-mode ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address --More--   shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim spt-threshold 1 ip pim rp-candidate Loopback0 group-list 1 interval 5 ip pim register-rate-limit 2 ip msdp peer 180.40.7.98 connect-source FastEthernet0/1 --More--  ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 102 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end --More--   R3# R3#conf gt ^ % Invalid input detected at '^' marker. R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no l int lo 0 R3(config)# *Mar 1 19:04:32.272: %BSR-5-CRP_REMOVED: Candidate-RP on interface Loopback0 has been removed R3(config)# *Mar 1 19:04:34.267: %LINK-5-CHANGED: Interface Loopback0, changed state to administratively down R3(config)#no ip mul R3(config)#no ip multicast- R3(config)#no ip multicast-routing r  R3(config)#no ip multicast-routing nt lo 0  ip pim rp-candidate lo0 group-list 1 interval 5do sh run | i ip pim rp-can  ip pim rp-candidate lo0 group-list 1 interval 5n ip pim rp-candidate lo0 group-list 1 interval 5o ip pim rp-candidate lo0 group-list 1 interval 5 ip pim rp-candidate lo0 group-list 1 interval 5 ^ % Invalid input detected at '^' marker. R3(config)#int fa 0/1 R3(config-if)#no ip pim sp R3(config-if)#no ip pim sparse-d R3(config-if)#no ip pim sparse-dense-mode R3(config-if)#int *Mar 1 19:05:00.041: %PIM-5-NBRCHG: neighbor 180.40.7.130 DOWN on interface FastEthernet0/1 (vrf default) DR R3(config-if)#int s 1/0 R3(config-if)#int s 1/0no ip pim sparse-dense-mode R3(config-if)#no ip pim sparse-dense-mode int s 1/0  *Mar 1 19:05:04.128: %PIM-5-NBRCHG: neighbor 180.40.7.35 DOWN on interface Serial1/0 (vrf default) DR R3(config-if)#int s 1/0 2 R3(config-if)#int s 1/2no ip pim sparse-dense-mode R3(config-if)# *Mar 1 19:05:06.780: %PIM-5-NBRCHG: neighbor 180.40.7.2 DOWN on interface Serial1/2 (vrf default) non DR R3(config-if)#do sh run | i pim ip pim spt-threshold 1 ip pim register-rate-limit 2 R3(config-if)#exit R3(config)#no ip pim register-rate-limit 2 R3(config)#^Z R3# *Mar 1 19:05:53.389: %SYS-5-CONFIG_I: Configured from console by console R3# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int u   tu 0 R4(config-if)# *Mar 1 19:08:59.711: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R4(config-if)#tun *Mar 1 19:09:02.103: %PIM-5-NBRCHG: neighbor 180.40.7.129 DOWN on interface FastEthernet0/0 (vrf default) non DR R4(config-if)#tun sou fa 0/0 R4(config-if)#tun des 180.40.7.98 R4(config-if)#ke *Mar 1 19:09:31.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R4(config-if)#ke R4(config-if)#keepalive R4(config-if)# R4(config-if)# R4(config-if)#ip address 24.24.24.2 2   4 255.255.255.0 R4(config-if)#ip pim sp R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)# RACK12AS>2 [Resuming connection 2 to r2 ... ] *M R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int tu 0 R2(config-if)#ip add *Mar 1 19:07:35.087: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R2(config-if)#ip add 24.24.24.2 255.255.255.0 R2(config-if)#tun sou fa 0/1 R2(config-if)#tun dest 180.40.7.130 R2(config-if)#kee R2(config-if)# *Mar 1 19:07:54.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#^Z R2#ping *Mar 1 19:08:04.848: %SYS-5-CONFIG_I: Configured from console by console R2#ping 244  24.         sh ip pinm *Mar 1 19:08:12.436: %PIM-5-NBRCHG: neighbor 24.24.24.4 UP on interface Tunnel0 (vrf default) R2#sh ip pinm    m nei *Mar 1 19:08:14.508: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.12 on Tunnel0 from LOADING to FULL, Loading Done R2#sh ip pim nei PIM Neighbor Table Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode 180.40.7.97 FastEthernet0/1 14:32:01/00:01:31 v2 1 / B S 180.40.7.66 Serial1/0.2 14:34:42/00:01:34 v2 1 / DR B S 24.24.24.4 Tunnel0 00:00:03/00:01:41 v2 1 / B S R2# R2# R2# R2#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 72 ms R2# R2# R2# RACK12AS>6 [Resuming connection 6 to r6 ... ] %Err S6#ping 22. 4.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK12AS>4 [Resuming connection 4 to r4 ... ] *Mar R4(config-if)#^Z R4#sh i *Mar 1 19:11:30.999: %SYS-5-CONFIG_I: Configured from console by console R4#sh i  p route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:39, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:39, FastEthernet0/0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:40, FastEthernet0/0 O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:40, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:40, FastEthernet0/0 --More--  O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:41, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:41, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:41, FastEthernet0/0 R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:51/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:00:51/00:00:00 FastEthernet0/0, Forward/Sparse-Dense, 00:00:51/00:00:00 (24.24.24.2, 224.4.4.4), 00:00:51/00:02:14, flags: LT Incoming interface: Tunnel0, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Sparse-Dense, 00:00:52/00:00:00 (*, 224.0.1.40), 14:33:58/00:02:19, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:01:07/00:00:00 FastEthernet0/0, Forward/Sparse-Dense, 14:16:58/00:00:00 R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map  R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#configt Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip mrou R4(config)#ip mroute ? A.B.C.D Source address vrf Select VPN Routing/Forwarding instance R4(config)#ip mroute 0.0.0.0 0.0.0.0 tun 0 R4(config)# R4(config)# R4(config)# R4(config)# R4(config)# R4(config)#^Z R4#sh ip *Mar 1 19:13:24.947: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:02:32/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:02:32/00:00:00 FastEthernet0/0, Forward/Sparse-Dense, 00:02:32/00:00:00 (24.24.24.2, 224.4.4.4), 00:02:32/00:00:33, flags: LT Incoming interface: Tunnel0, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Sparse-Dense, 00:02:33/00:00:00 (*, 224.0.1.40), 14:35:40/00:02:43, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:02:49/00:00:00 FastEthernet0/0, Forward/Sparse-Dense, 14:18:39/00:00:00 R4#  sh ip mrouteconfig t t sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:04, expires: 00:03:23 R4# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 36 ms S6# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 104 ms R7# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#ping 224.4  .7.7.7. % Unrecognized host or address, or protocol not running. R4#ping 224.7.7.7.  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 172 ms Reply to request 0 from 17.100.1.2, 172 ms R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:03:36/00:02:41, RP 223.254.254.254, flags: SCL Incoming interface: Tunnel0, RPF nbr 24.24.24.2, Mroute Outgoing interface list: FastEthernet0/0, Forward/Sparse-Dense, 00:03:36/00:02:41 (*, 224.7.7.7), 00:00:08/stopped, RP 223.254.254.254, flags: SPF Incoming interface: Tunnel0, RPF nbr 24.24.24.2, Mroute Outgoing interface list: Null (180.40.7.130, 224.7.7.7), 00:00:09/00:02:58, flags: PFT Incoming interface: FastEthernet0/0, RPF nbr 0.0.0.0, Registering Outgoing interface list: Null (*, 224.0.1.40), 14:36:43/00:02:35, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:03:52/00:00:00 FastEthernet0/0, Forward/Sparse-Dense, 14:19:43/00:00:00 --More--   R4#sh ip mroute s R4#sh ip mroute s % Ambiguous command: "sh ip mroute s" R4#sh ip mroute s st R4#sh ip mroute static Mroute: 0.0.0.0/0, interface: Tunnel0 Protocol: none, distance: 0, route-map: none R4# RACK12AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b Tun interface Tunnel0 ip address 24.24.24.2 255.255.255.0 ip pim sparse-dense-mode keepalive 10 3 tunnel source FastEthernet0/1 tunnel destination 180.40.7.130 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 224.66.66.66 Prob13 duplex auto speed auto --More--  ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! --More--   R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#sh run         RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#sh run |     int tu 0 Building configuration... Current configuration : 167 bytes ! interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode keepalive 10 3 tunnel source FastEthernet0/0 tunnel destination 180.40.7.98 end R4# R4#sh run | i ip mroute ip mroute 0.0.0.0 0.0.0.0 Tunnel0 R4# R4#copnfi      nfig t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#no ip mroute 0.0.0.0 .0.0.     0.0.0.0 tu  tu 0 R4(config)#int tu 0 R4(config-if)#do sh ip ops pf     spf int tu 0 Tunnel0 is up, line protocol is up Internet Address 24.24.24.4/24, Area 0 Process ID 1, Router ID 192.10.32.12, Network Type POINT_TO_POINT, Cost: 11111 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 Hello due in 00:00:09 Index 3/3, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 2.2.2.2 Suppress hello for 0 neighbor(s) R4(config-if)#do sh ip ospf int tu 0int tu 0 do sh ip ospf int tu 0                      int tu 0 R4(config-if)#ip ospf cost 1 R4(config-if)# *Mar 1 19:18:48.847: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 19:18:49.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 19:18:49.847: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 19:18:49.851: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#ip ospf cost 1nip ospf cost 1oip ospf cost 1 ip ospf cost 1 R4(config-if)#exit R4(config)#router eigrp 1 R4(config-router)#no autop ^ % Invalid input detected at '^' marker. R4(config-router)#no autop\  ^ % Invalid input detected at '^' marker. R4(config-router)#no autop  R4(config-router)# *Mar 1 19:19:59.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 19:19:59.887: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4(config-router)# *Mar 1 19:20:01.851: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Tunnel0 from LOADING to FULL, Loading Done R4(config-router)#net 180.40.7.130 0,.0   .0.0.0 R4(config-router)# RACK12AS>3 [Resuming connection 3 to r3 ... ] R3#confit  t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#rouetr     ter eigrp 1 R3(config-router)#no auto R3(config-router)#net 180.40.7.129 0.0.00 .0 R3(config-router)#net 180.40.7.129 0.0.0.0 *Mar 1 19:18:20.233: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor 180.40.7.130 (FastEthernet0/1) is up: new adjacency R3(config-router)#net 180.40.7.129 0.0.0.0 0.0.0.0  0.0.0.0  0.0.0.0 3 0.0.0.0 R3(config-router)# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router os  eigrp 1 R2(config-router)#no auto R2(config-router)#net 180.40.7.98 0.0.0.0 R2(config-router)#net 180.40.7.3              net 180.40.7.98 0.0.0.0nnet 180.40.7.98 0.0.0.0onet 180.40.7.98 0.0.0.0 net 180.40.7.98 0.0.0.0 R2(config-router)#int lo 1 R2(config-if)#ip address 2.2.2.2 255.255.255.255 R2(config-if)#int u 0     tu 0 R2(config-if)#tun sou lo 1 R2(config-if)#tun des 4.4.4.4 R2(config-if)# RACK12AS>4 [Resuming connection 4 to r4 ... ] *Mar R4(config-router)#in tlo    t lo 1 R4(config-if)#ip address 4.4.4.4 255.255.255.255 R4(config-if)#in tu 0 R4(config-if)#tun sou lo 1 R4(config-if)#tun des 2.2.2.2 R4(config-if)#router *Mar 1 19:23:19.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 19:23:19.847: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 19:23:19.851: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#router eigrp 1 R4(config-router)#net 4.4.4.4.  0.0 *Mar 1 19:23:29.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R4(config-router)#net 4.4.4.4 0.0.0.0 R4(config-router)# *Mar 1 19:23:32.443: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4(config-router)# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Mar R2(config-if)#router rigrp \       eigrp 1 R2(config-router)# *Mar 1 19:21:12.868: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.12 on Tunnel0 from LOADING to FULL, Loading Done R2(config-router)#net 2.2.2.2 0.0.0.0 R2(config-router)#do shrun      run | b eigrp router eigrp 1 network 2.2.2.2 0.0.0.0 no auto-summary ! router ospf 1 router-id 2.2.2.2 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 5 ip msdp peer 180.40.7.129 connect-source FastEthernet0/1 ! ip access-list extended Prob13 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! --More--   R2(config-router)#net 180.40.7.2 0.0.0.0 R2(config-router)# RACK12AS>3 4 [Resuming connection 4 to r4 ... ] *M R4(config-router)#^Z R4#sh ip route *Mar 1 19:24:20.759: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:34, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:34, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/20642560] via 180.40.7.129, 00:00:06, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:34, FastEthernet0/0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback1 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:03:30, FastEthernet0/0 O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:39, FastEthernet0/0 R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int tu 0 R4(config-if)#ip ospf cost ` ^ % Invalid input detected at '^' marker. R4(config-if)#ip ospf cost ` 1 R4(config-if)#ip ospf cost 1 ^Z R4#config tsh ip route *Mar 1 19:25:16.271: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 24.24.24.2, 00:00:14, Tunnel0 O 17.100.1.0 [110/792] via 24.24.24.2, 00:00:14, Tunnel0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/20642560] via 180.40.7.129, 00:01:02, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 24.24.24.2, 00:00:14, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback1 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:04:23, FastEthernet0/0 O 180.40.7.35/32 [110/1] via 24.24.24.2, 00:00:16, Tunnel0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:16, FastEthernet0/0 O 180.40.7.66/32 [110/782] via 24.24.24.2, 00:00:16, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:16, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:16, Tunnel0 R4# RACK12AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 64 ms S6# RACK12AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 128 ms R7#^x2 % Unknown command or computer name, or unable to find computer address R7# R7# RACK12AS>2 [Resuming connection 2 to r2 ... ] * R2(config-router)#sh    ^Z R2#sh reun *Mar 1 19:24:35.945: %SYS-5-CONFIG_I: Configured from console by console R2#sh reun     un | b Lo interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface Loopback1 ip address 2.2.2.2 255.255.255.255 ! interface Tunnel0 ip address 24.24.24.2 255.255.255.0 ip pim sparse-dense-mode keepalive 10 3 tunnel source Loopback1 tunnel destination 4.4.4.4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown --More--  ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 224.66.66.66 Prob13 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode --More--   ip ospf network point-to-multipoint frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown --More--  ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router eigrp 1 network 2.2.2.2 0.0.0.0 network 180.40.7.2 0.0.0.0 no auto-summary ! router ospf 1 router-id 2.2.2.2 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server --More--   R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] *Mar R3(config-router)#sh    ^Z R3#dsh      *Mar 1 19:25:18.026: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b router router eigrp 1 network 180.40.7.3 0.0.0.0 network 180.40.7.129 0.0.0.0 no auto-summary ! router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim spt-threshold 1 ip msdp peer 180.40.7.98 connect-source FastEthernet0/1 ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 102 permit ip any any ! ! ! --More--   R3#q config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip pim spt-threshold 1 R3(config)#no ip msdp peer 180.40.7.98 connect-source FastEthernet0/1 R3(config)#^Z R3# *Mar 1 19:25:47.578: %MSDP-5-PEER_UPDOWN: Session to peer 180.40.7.98 going down *Mar 1 19:25:48.399: %SYS-5-CONFIG_I: Configured from console by console R3# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | % Incomplete command. R4# sh run | Lo ^ % Invalid input detected at '^' marker. R4#sh run | Lo bLo Lo interface Loopback1 ip address 4.4.4.4 255.255.255.255 ! interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode ip ospf cost 1 keepalive 10 3 tunnel source Loopback1 tunnel destination 2.2.2.2 ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 8 ip pim sparse-dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto ! interface ATM1/0 ip address 192.10.32.12 255.255.255.0 ip nat outside --More--   no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 broadcast ! ! router eigrp 1 network 4.4.4.4 0.0.0.0 network 180.40.7.130 0.0.0.0 no auto-summary ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip nat inside source list IPNAT interface ATM1/0 overload no ip http server no ip http secure-server ip classless ! ip pim bidir-enable ip pim spt-threshold 1 ! ! --More--   R4# R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int     int tu 0 R4(config-if)#int tu 0p ospf cost 1nip ospf cost 1oip ospf cost 1 ip ospf cost 1 R4(config-if)#no router eigrp 1 *Mar 1 19:29:23.415: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor 180.40.7.129 (FastEthernet0/0) is down: interface down RACK12AS>3 [Resuming connection 3 to r3 ... ] *M R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no rotuer      uter eigrp 1 RACK12AS>4 [Resuming connection 4 to r4 ... ] R4( R4# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router      no rotuer      uter iepg    eigrp 1 R2(config)#router eigrp 1 R2(config-router)#router eigrp 1nrouter eigrp 1orouter eigrp 1 router eigrp 1 R2(config)#router ospf 1 R2(config-router)#net 2.2.2.2 0.0.0.0 area 51 R2(config-router)# *Mar 1 19:28:35.361: %OSPF-6-AREACHG: 2.2.2.2/32 changed from area 0 to area 51 R2(config-router)#net 2.2.2.2 0.0.0.0 area 51 net 180.40.7.2 0.0.0.0 area 41  51 R2(config-router)#^Z R2# *Mar 1 19:28:46.219: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 19:28:46.223: %OSPF-6-AREACHG: 180.40.7.2/32 changed from area 0 to area 51 *Mar 1 19:28:46.784: %SYS-5-CONFIG_I: Configured from console by console R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] *Ma R3(config)#co  router ospf 1 R3(config-router)#net 180.40.7.3 0.0.0.0 area 51 R3(config-router)#net 180.40.7.3 0.0.0.0 area 51 *Mar 1 19:28:55.098: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-router)#net 180.40.7.3 0.0.0.0 area 51 *Mar 1 19:28:55.098: %OSPF-6-AREACHG: 180.40.7.3/32 changed from area 0 to area 51 R3(config-router)#net 180.40.7.3 0.0.0.0 area 51 0.0.0.0 area 51 1 0.0.0.0 area 512 0.0.0.0 area 519 0.0.0.0 area 51 R3(config-router)# *Mar 1 19:29:00.703: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.12 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-router)#^Z R3# *Mar 1 19:29:00.703: %OSPF-6-AREACHG: 180.40.7.129/32 changed from area 0 to area 51 *Mar 1 19:29:01.272: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.130, FastEthernet0/1 R3# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#confi g ^ % Invalid input detected at '^' marker. R4#confi g t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#router ospfg 1 ^ % Invalid input detected at '^' marker. R4(config)# *Mar 1 19:31:38.847: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 19:31:39.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 19:31:39.847: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 19:31:39.851: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config)#router ospfg 1g 1  R4(config-router)#net 4.4.4.4 0.0.0.0 area 51 R4(config-router)#net *Mar 1 19:31:50.119: %OSPF-6-AREACHG: 4.4.4.4/32 changed from area 0 to area 51 R4(config-router)#net 180.40.7.130 0.0.0.0-    0 artea   r ea 51 R4(config-router)#^Z R4# *Mar 1 19:32:03.455: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 19:32:03.459: %OSPF-6-AREACHG: 180.40.7.130/32 changed from area 0 to area 51 R4# *Mar 1 19:32:04.203: %SYS-5-CONFIG_I: Configured from console by console R4# *Mar 1 19:32:11.599: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on FastEthernet0/0 from LOADING to FULL, Loading Done R4# *Mar 1 19:32:49.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R4# *Mar 1 19:32:52.451: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4# *Mar 1 19:33:00.131: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Tunnel0 from LOADING to FULL, Loading Done R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/11902] via 24.24.24.2, 00:00:46, Tunnel0 O 17.100.1.0 [110/11902] via 24.24.24.2, 00:00:46, Tunnel0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:01:36, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/11112] via 24.24.24.2, 00:00:46, Tunnel0 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback1 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:01:39, FastEthernet0/0 O 180.40.7.35/32 [110/11111] via 24.24.24.2, 00:00:49, Tunnel0 O 180.40.7.33/32 [110/11892] via 24.24.24.2, 00:00:49, Tunnel0 O 180.40.7.66/32 [110/11892] via 24.24.24.2, 00:00:49, Tunnel0 O 180.40.7.65/32 [110/11111] via 24.24.24.2, 00:00:49, Tunnel0 O 180.40.7.96/27 [110/11112] via 24.24.24.2, 00:00:49, Tunnel0 R4#sh ip ospf data OSPF Router with ID (192.10.32.12) (Process ID 1) Router Link States (Area 0) Link ID ADV Router Age Seq# Checksum Link count 2.2.2.2 2.2.2.2 88 0x80000013 0x00E002 8 3.3.3.3 3.3.3.3 178 0x80000006 0x007A6A 2 17.57.100.2 17.57.100.2 74 0x80000025 0x00A39F 1 17.100.1.2 17.100.1.2 240 0x80000026 0x0067C5 1 180.40.7.66 180.40.7.66 102 0x8000002F 0x00BBD8 4 180.40.7.97 180.40.7.97 355 0x8000002D 0x00E70A 1 192.10.32.12 192.10.32.12 88 0x8000003B 0x0091AC 3 Net Link States (Area 0) Link ID ADV Router Age Seq# Checksum 17.57.100.2 17.57.100.2 74 0x80000024 0x00B727 17.100.1.1 180.40.7.66 102 0x80000024 0x00F8E1 180.40.7.97 180.40.7.97 355 0x80000002 0x004739 Summary Net Link States (Area 0) --More--  Link ID ADV Router Age Seq# Checksum 2.2.2.2 2.2.2.2 202 0x80000001 0x00FA31 2.2.2.2 3.3.3.3 174 0x80000001 0x007A9D 2.2.2.2 192.10.32.12 128 0x80000001 0x009E8D 4.4.4.4 2.2.2.2 127 0x80000001 0x0046CC 4.4.4.4 3.3.3.3 128 0x80000001 0x008A94 4.4.4.4 192.10.32.12 158 0x80000001 0x009A9A 180.40.7.0 2.2.2.2 197 0x80000001 0x00D38C 180.40.7.0 3.3.3.3 183 0x80000001 0x00B5A6 180.40.7.0 192.10.32.12 128 0x80000001 0x00D996 180.40.7.128 2.2.2.2 131 0x80000003 0x00D408 180.40.7.128 3.3.3.3 133 0x80000003 0x0019CF 180.40.7.128 192.10.32.12 133 0x80000003 0x0033CA Router Link States (Area 51) Link ID ADV Router Age Seq# Checksum Link count 2.2.2.2 2.2.2.2 180 0x80000003 0x00DA47 3 3.3.3.3 3.3.3.3 143 0x80000004 0x00B8A1 3 192.10.32.12 192.10.32.12 143 0x80000003 0x000A4B 2 Net Link States (Area 51) --More--  Link ID ADV Router Age Seq# Checksum 180.40.7.129 3.3.3.3 144 0x80000001 0x009054 Summary Net Link States (Area 51) Link ID ADV Router Age Seq# Checksum 17.57.100.0 2.2.2.2 228 0x80000001 0x0072F9 17.57.100.0 3.3.3.3 204 0x80000001 0x00F166 17.57.100.0 192.10.32.12 95 0x80000001 0x00FCED 17.100.1.0 2.2.2.2 228 0x80000001 0x00B1F2 17.100.1.0 3.3.3.3 204 0x80000001 0x00315F 17.100.1.0 192.10.32.12 95 0x80000001 0x003CE6 24.24.24.0 2.2.2.2 115 0x80000001 0x0078E1 24.24.24.0 3.3.3.3 113 0x80000001 0x00F74E 24.24.24.0 192.10.32.12 115 0x80000001 0x0074F6 180.40.7.33 2.2.2.2 228 0x80000001 0x0043DC 180.40.7.33 3.3.3.3 204 0x80000001 0x0087A4 180.40.7.33 192.10.32.12 95 0x80000001 0x00CDD0 180.40.7.35 2.2.2.2 230 0x80000001 0x00919C 180.40.7.35 3.3.3.3 206 0x80000001 0x001109 180.40.7.35 192.10.32.12 96 0x80000001 0x001C90 180.40.7.65 2.2.2.2 230 0x80000001 0x0064AB 180.40.7.65 3.3.3.3 206 0x80000001 0x00E318 --More--   R4# RACK12AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh run | b ospf ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode clock rate 64000 ! interface Serial1/3 no ip address shutdown --More--  ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 router-id 2.2.2.2 log-adjacency-changes network 2.2.2.2 0.0.0.0 area 51 network 180.40.7.2 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 --More--  ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 5 ip msdp peer 180.40.7.129 connect-source FastEthernet0/1 ! ip access-list extended Prob13 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! ! ! ! ! ! --More--   R2# RACK12AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run | b router router ospf 1 router-id 3.3.3.3 log-adjacency-changes network 180.40.7.3 0.0.0.0 area 51 network 180.40.7.129 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 102 permit ip any any ! ! ! ! ! ! ! ! --More--   R3# RACK12AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b router router ospf 1 log-adjacency-changes network 4.4.4.4 0.0.0.0 area 51 network 180.40.7.130 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ip nat inside source list IPNAT interface ATM1/0 overload no ip http server no ip http secure-server ip classless ! ip pim bidir-enable ip pim spt-threshold 1 ! ! ip access-list standard IPNAT permit 180.40.7.0 0.0.0.255 permit 17.0.0.0 0.255.255.255 ! ! ! ! ! --More--   R4# [Connection to r4 closed by foreign host] RACK12AS>r5 Translating "r5" Trying R5 (1.1.1.1, 2005)... Open ************************************************************** Global Knowledge Hands-On Labs Access Server Access is restricted to Global Knowledge CCIE Students ************************************************************** Please re-enter your password. (This is the same password you used to log onto the Lab website.) If you see a username prompt, please wait 40 seconds and try again. If the username prompt persists, please reset equipment from your "Pod x" link. User Access Verification Password: Password OK S5>en S5# S5# S5# S5#sh lms qwo  o      mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Default DSCP Mutation Map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 S5# S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#mls qos map co S5(config)#mls qos map cos-dscp ? <0-63> 8 dscp values separated by spaces S5(config)#mls qos map cos-dscp              map dsc S5(config)#mls qos map dscp-c S5(config)#mls qos map dscp-cos ? <0-63> DSCP values separated by spaces (up to 8 values total) S5(config)#mls qos map dscp-cos 8 ? <0-63> DSCP values separated by spaces (up to 8 values total) to Specify COS S5(config)#mls qos map dscp-cos 8 to ? <0-7> cos value S5(config)#mls qos map dscp-cos 8 to                           ^Z S5#sh ml 1d00h: %SYS-5-CONFIG_I: Configured from console by console S5#sh mlm   mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int gi 0/1 S5(config-if)#wrr ds S5(config-if)#wrr dscp-map ? <1-2> enter dscp-map threshold id (1-2) S5(config-if)#wrr dscp-map 1 ? <0-63> DSCP values separated by spaces (up to 8 values total) S5(config-if)#wrr dscp-map 1 16 S5(config-if)#do sh w       ^Z S5#sh 1d00h: %SYS-5-CONFIG_I: Configured from console by console S5#sh wrr S5#sh wrr   mls qos wrr S5#sh mls qos wrr? % Unrecognized command S5#sh mls qos wrr           w? % Unrecognized command S5#sh w mls qos in S5#sh mls qos interface ? FastEthernet FastEthernet IEEE 802.3 GigabitEthernet GigabitEthernet IEEE 802.3z buffers Show buffer information policers Show policers information queueing Show queueing information statistics Show statistics | Output modifiers S5#sh mls qos interface qu S5#sh mls qos interface queueing ? | Output modifiers S5#sh mls qos interface queueing          gi 01 /1 GigabitEthernet0/1 QoS is disabled. pass-through mode When QoS is enabled, following settings will be applied trust state: not trusted trust mode: not trusted COS override: dis default COS: 0 DSCP Mutation Map: Default DSCP Mutation Map Trust device: none S5#sh mls qos interface gi 0/1                Au9eub ^ % Invalid input detected at '^' marker. S5# S5#en S5# S5#sh wr S5#sh wr? % Unrecognized command S5#sh wr  qu S5#sh queue? queue queueing S5#sh queue ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface EsconPhy ESCON interface FastEthernet FastEthernet IEEE 802.3 Filter Filter interface Filtergroup Filter Group interface GigabitEthernet GigabitEthernet IEEE 802.3z Group-Async Async Group interface Lex Lex interface LongReachEthernet Long-Reach Ethernet interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Portgroup Portgroup interface Pos-channel POS Channel of interfaces SYSCLOCK Telecom-Bus Clock Controller Tunnel Tunnel interface Vif PGM Multicast Host interface --More--   Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing Vlan Catalyst Vlans fcpa Fiber Channel voaBypassIn VOA-Bypass-In interface voaBypassOut VOA-Bypass-Out interface voaFilterIn VOA-Filter-In interface voaFilterOut VOA-Filter-Out interface voaIn VOA-In interface voaOut VOA-Out interface S5#sh queue int S5#sh queue int   ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface EsconPhy ESCON interface FastEthernet FastEthernet IEEE 802.3 Filter Filter interface Filtergroup Filter Group interface GigabitEthernet GigabitEthernet IEEE 802.3z Group-Async Async Group interface Lex Lex interface LongReachEthernet Long-Reach Ethernet interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Portgroup Portgroup interface Pos-channel POS Channel of interfaces SYSCLOCK Telecom-Bus Clock Controller Tunnel Tunnel interface Vif PGM Multicast Host interface --More--   S5#sh queue qi S5#sh queue qi  gi S5#sh queue gigabitEthernet ? <0-1> GigabitEthernet interface number S5#sh queue gigabitEthernet 0/1 ? <0-16> Queue number | Output modifiers S5#sh queue gigabitEthernet 0/1 'Show queue' not supported with FIFO queueing. S5#sh mls qos map Policed-dscp map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 Dscp-cos map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 01 01 1 : 01 01 01 01 01 01 02 02 02 02 2 : 02 02 02 02 03 03 03 03 03 03 3 : 03 03 04 04 04 04 04 04 04 04 4 : 05 05 05 05 05 05 05 05 06 06 5 : 06 06 06 06 06 06 07 07 07 07 6 : 07 07 07 07 Dscp-switch priority map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 00 00 00 00 00 00 00 00 00 1 : 00 00 00 00 00 00 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 02 02 02 02 02 02 02 02 4 : 02 02 02 02 02 02 02 02 03 03 5 : 03 03 03 03 03 03 03 03 03 03 6 : 03 03 03 03 Cos-dscp map: cos: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 IpPrecedence-dscp map: ipprec: 0 1 2 3 4 5 6 7 -------------------------------- dscp: 0 8 16 24 32 40 48 56 Dscp-dscp mutation map: Default DSCP Mutation Map: --More--   d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 00 01 02 03 04 05 06 07 08 09 1 : 10 11 12 13 14 15 16 17 18 19 2 : 20 21 22 23 24 25 26 27 28 29 3 : 30 31 32 33 34 35 36 37 38 39 4 : 40 41 42 43 44 45 46 47 48 49 5 : 50 51 52 53 54 55 56 57 58 59 6 : 60 61 62 63 S5#sh queue S5#sh queuei S5#sh queueing ? interface custom custom queueing list configuration fair fair queueing configuration priority priority queueing list configuration random-detect random early detection configuration | Output modifiers S5#sh queueing ra S5#sh queueing random-detect ? interface | Output modifiers S5#sh queueing random-detect int g  i 0/1 Current random-detect configuration: S5#sh mls qos ? aggregate-policer Show aggregate-policer information interface Show interface information maps Show mapping information | Output modifiers S5#sh mls qos int ? FastEthernet FastEthernet IEEE 802.3 GigabitEthernet GigabitEthernet IEEE 802.3z buffers Show buffer information policers Show policers information queueing Show queueing information statistics Show statistics | Output modifiers S5#sh mls qos int qu S5#sh mls qos int queueing ? | Output modifiers S5#sh mls qos int queueing          gi 0/1 ? buffers Show buffer information policers Show policers information queueing Show queueing information statistics Show statistics | Output modifiers S5#sh mls qos int gi 0/1 qu S5#sh mls qos int gi 0/1 queueing ? | Output modifiers S5#sh mls qos int gi 0/1 queueing GigabitEthernet0/1 QoS is disabled. Only one queue is used When QoS is enabled, following settings will be applied Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 Dscp-threshold map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 01 01 01 01 01 01 01 01 01 01 1 : 01 01 01 01 01 01 01 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 01 01 01 01 01 01 01 01 4 : 01 01 01 01 01 01 01 01 01 01 5 : 01 01 01 01 01 01 01 01 01 01 6 : 01 01 01 01 Cos-queue map: cos-qid 0 - 1 1 - 1 2 - 2 3 - 2 4 - 3 5 - 3 6 - 4 7 - 4 S5#confi gt ^ % Invalid input detected at '^' marker. S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#on  int gi 0/1 S5(config-if)#int gi 0/1wrr dscp-map 1 161 16 2 16 S5(config-if)#^Z S5#config t gt 1d00h: %SYS-5-CONFIG_I: Configured from console by console S5#confi gtsh mls qos int gi 0/1 queueing GigabitEthernet0/1 QoS is disabled. Only one queue is used When QoS is enabled, following settings will be applied Egress expedite queue: dis wrr bandwidth weights: qid-weights 1 - 25 2 - 25 3 - 25 4 - 25 Dscp-threshold map: d1 : d2 0 1 2 3 4 5 6 7 8 9 --------------------------------------- 0 : 01 01 01 01 01 01 01 01 01 01 1 : 01 01 01 01 01 01 02 01 01 01 2 : 01 01 01 01 01 01 01 01 01 01 3 : 01 01 01 01 01 01 01 01 01 01 4 : 01 01 01 01 01 01 01 01 01 01 5 : 01 01 01 01 01 01 01 01 01 01 6 : 01 01 01 01 Cos-queue map: cos-qid 0 - 1 1 - 1 2 - 2 3 - 2 4 - 3 5 - 3 6 - 4 7 - 4 S5#sh mls qos int gi 0/1 queueing                                q S5 con0 is now available Press RETURN to get started.