=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.11.02 18:53:04 =~=~=~=~=~=~=~=~=~=~=~= R2# R2# R2# R2# RACK98AS>4 [Resuming connection 4 to r4 ... ] R4#sh run     ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset up up ATM1/0 192.10.32.1 YES manual up up R4#cpo   o config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int at      default int atm 1./0   /0 Building configuration... default ! ^ % Invalid input detected at '^' marker. default protocol ip 192.10.32.254 broadcast ^ % Invalid input detected at '^' marker. Interface ATM1/0 set to default configuration R4(config)#^Z R4#config tsh ip int brie *Mar 1 05:56:00.486: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset up up ATM1/0 unassigned YES TFTP up up R4#confifg tr ^ % Invalid input detected at '^' marker. R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int at,   m 1/0 R4(config-if)#shut R4(config-if)#^Z R4# *Mar 1 05:56:12.394: %SYS-5-CONFIG_I: Configured from console by console R4# *Mar 1 05:56:14.018: %LINK-5-CHANGED: Interface ATM1/0, changed state to administratively down *Mar 1 05:56:15.018: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ipv R4(config)#ipv6 un R4(config)#ipv6 unicast-routing R4(config)#int lo 0 R4(config-if)#ipv add 2000:4:4::/64 R4(config-if)#int fa 0/0 R4(config-if)#ipv add 2005:0:104::4::  /64 R4(config-if)#ipv add fe80::4 ? link-local Use link-local address R4(config-if)#ipv add fe80::4 link R4(config-if)#^Z R4#s *Mar 1 05:58:02.722: %SYS-5-CONFIG_I: Configured from console by console R4#sh ipv int brie FastEthernet0/0 [up/up] FE80::4 2005:0:104::4 ATM1/0 [administratively down/down] unassigned Loopback0 [up/up] FE80::202:16FF:FE51:F560 2000:4:4:: R4# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv un R1(config)#ipv unicast-routing R1(config)# R1(config)#int e 0/1 R1(config-if)#ipv add 2005:0:104::1/64 R1(config-if)#ipv add fe80::1 link R1(config-if)#int s 0/.1  1 R1(config-if)#int s 0/1pv add fe80::1 link R1(config-if)#ipv add fe80::1 linknt s 0/1 pv add fe80::1 link2005:0:104::1/64::1/64 2::1/64 R1(config-if)#^Z R1#sh *Mar 1 05:58:38.714: %SYS-5-CONFIG_I: Configured from console by console R1#sh ipv int brie Ethernet0/0 [up/up] unassigned Serial0/0 [administratively down/down] unassigned Ethernet0/1 [up/up] FE80::1 2005:0:104::1 Serial0/1 [up/up] FE80::1 2005:0:102::1 R1# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int     ipv un R2(config)#ipv unicast-routing R2(config)#int s 1/1 R2(config-if)#ipv add 2005:0:102::2  /5 64 R2(config-if)#ipv add fe80::2 link R2(config-if)#ipv add fe80::2 link2005:0:102::2/64nt s 1/1  2 R2(config-if)#int s 1/2pv add fe80::2 link R2(config-if)#ipv add 2005:0:1203::2  /64 R2(config-if)#ipv add 2005:0:1203::2/64fe80::2 link nt s 1/2  0.1 R2(config-subif)#int s 1/0.1pv add 2005:0:1203::2/64::2/64 ::2/64 ::2/64 ::2/64 2::2/643::2/647::2/64 R2(config-subif)#ipv add 2005:0:237::2/64nt s 1/0.1 pv add 2005:0:1203::2/64fe80::2 link  R2(config-subif)#ipv add fe80::2 link2005:0:237::2/64nt s 1/0.1  2 R2(config-subif)#int s 1/0.2pv add fe80::2 link R2(config-subif)#ipv add fe80::2 linknt s 1/0.2 pv add fe80::2 link2005:0:237::2/64::2/64 ::2/64 ::2/64 7::2/640::2/642::2/64 R2(config-subif)#end R2#sh ip *Mar 1 05:59:42.927: %SYS-5-CONFIG_I: Configured from console by console R2#sh ipv int brie FastEthernet0/0 [administratively down/down] unassigned BRI0/0 [administratively down/down] unassigned BRI0/0:1 [administratively down/down] unassigned BRI0/0:2 [administratively down/down] unassigned FastEthernet0/1 [administratively down/down] unassigned Serial1/0 [up/up] unassigned Serial1/0.1 [up/up] FE80::2 2005:0:237::2 Serial1/0.2 [up/up] FE80::2 2005:0:702::2 Serial1/1 [up/up] FE80::2 2005:0:102::2 Serial1/2 [up/up] FE80::2 --More--   2005:0:1203::2 Serial1/3 [administratively down/down] unassigned Serial1/4 [administratively down/down] unassigned Serial1/5 [administratively down/down] unassigned Serial1/6 [administratively down/down] unassigned Serial1/7 [administratively down/down] unassigned R2#ping fe80::1 Output Interface: serial1/1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to FE80::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/37/60 ms R2#serial1/1ping fe80::1 Output Interface: ping fe80::1serial1/1  1/1 % Bad interface R2#serial 1/1  RACK98AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ipv i un R3(config)#ipv unicast-routing R3(config)#int lo 0 R3(config-if)#ipv add 2000:3:3::/64 R3(config-if)#int s 1/2 R3(config-if)#ipv add 2005:0:1203::3/64 R3(config-if)#ipv add fe e08  80::3 link R3(config-if)#ipv add fe80::3 link2005:0:1203::3/64nt s 1/2  0 R3(config-if)#int s 1/0pv add fe80::3 link R3(config-if)#ipv add fe80::3 linknt s 1/0 pv add fe80::3 link2005:0:1203::3/64::3/64 ::3/64 ::3/64 ::3/64 2::3/643::3/647::3/64 R3(config-if)#^Z R3# *Mar 1 06:01:29.870: %SYS-5-CONFIG_I: Configured from console by console R3# RACK98AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv un R7(config)#ipv unicast-routing R7(config)#int s 1/0.1 R7(config-subif)#ipov   pv add 2005:0:237::7  /64 R7(config-subif)#ipv add fe80::7 link R7(config-subif)#ipv add fe80::7 link2005:0:237::7/64nt s 1/0.1  2 R7(config-subif)#int s 1/0.2pv add fe80::7 link2005:0:237::7/64fe80::7 link  R7(config-subif)#ipv add fe80::7 linknt s 1/0.2 pv add fe80::7 link2005:0:237::7/64::7/64 ::7/64 ::7/64 7::7/640::7/642::7/64 R7(config-subif)#^Z R7# *Mar 1 06:02:12.725: %SYS-5-CONFIG_I: Configured from console by console R7#ping 2005:0:702::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:702::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/64 ms R7#ping 2005:0:702::2 3::3 ::3 ::3 2::33::37::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: .. RACK98AS>3 [Resuming connection 3 to r3 ... ] R3#sh run int s 1/0 Building configuration... Current configuration : 133 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local end R3#configt Translating "configt" Translating "configt" Translating "configt" % Unknown command or computer name, or unable to find computer address R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#int s 1/0 R3(config-if)#fram map ipv 2005:0:237::2 302 br R3(config-if)#fram map ipv 2005:0:237::2 302 broadcast R3(config-if)#fram map ipv 2005:0:237::2 302 broadcast  302 broadcast 7 302 broadcast  R3(config-if)#fram map ipv 2005:0:237::7 302 broadcast nfram map ipv 2005:0:237::7 302 broadcast ofram map ipv 2005:0:237::7 302 broadcast  fram map ipv 2005:0:237::7 302 broadcast  R3(config-if)#no fram map ipv 2005:0:237::7 302 broadcast fram map ipv 2005:0:237::7 302 broadcast  broadcast 7 broadcast  R3(config-if)#^Z R3# RACK98AS>7 [Resuming connection 7 to r7 ... ] .. R7#ping 2005:0:237::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/61 ms R7# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2#ping 2005:0:1203::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:1203::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms R2#ping 2005:0:1203::3::3 ::3 ::3 ::3 2::33::37::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 56/57/60 ms R2#ping 2005:0:237::3 7 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:237::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 164/165/168 ms R2# R2# R2# R2# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1#ping 2005:0:104::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/8 ms R1#ping 2005:0:104::4:4 2::2 2::2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:102::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/35/52 ms R1#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Ethernet0/0 ip address 180.40.7.66 255.255.255.224 half-duplex ! interface Serial0/0 no ip address shutdown --More--  ! interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::1/64 ipv6 address FE80::1 link-local ! interface Serial0/1 no ip address ipv6 address 2005:0:102::1/64 ipv6 address FE80::1 link-local clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! no ip http server ip classless ! ! ! --More--   R1# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address --More--   shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::2/64 ipv6 address FE80::2 link-local frame-relay interface-dlci 203 ! --More--  interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::2/64 ipv6 address FE80::2 link-local frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ipv6 address FE80::2 link-local ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 address FE80::2 link-local clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown --More--   R2# RACK98AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 no ip address --More--   ipv6 address 2000:3:3::/64 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local frame-relay map ipv6 2005:0:237::2 302 broadcast --More--   frame-relay map ipv6 2005:0:237::7 307 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::3/64 ipv6 address FE80::3 link-local ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! --More--   R3# RACK98AS>4 [Resuming connection 4 to r4 ... ] R4#sh run|      n | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 no ip address ipv6 address 2000:4:4::/64 ! interface FastEthernet0/0 --More--   no ip address duplex auto speed auto ipv6 address 2005:0:104::4/64 ipv6 address FE80::4 link-local ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! no ip http server no ip http secure-server ip classless ! ! ! ! ! ! ! ! line con 0 --More--   R4# RACK98AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | b ipv ipv6 unicast-routing ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address --More--   shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.1 255.255.255.224 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80::7 link-local frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point --More--   ipv6 address 2005:0:702::7/64 --More--   ipv6 address FE80::7 link-local --More--   frame-relay interface-dlci 702 --More--  ! --More--  interface Serial1/1 --More--   no ip address --More--   shutdown --More--  ! --More--   R7# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e e 0/1 R1(config-if)#ipv R1(config-if)#ipv6 rip ? WORD User selected string identifying this RIP process R1(config-if)#ipv6 rip R1Rip en R1(config-if)#int s 1/  90  0. /1 R1(config-if)#int s 0/1pv6 rip R1Rip en R1(config-if)#^Z R1# RACK98AS>4 [Resuming connection 4 to r4 ... ] R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo 0 R4(config-if)#ipv rip R4Rip en R4(config-if)#int fa 0/0 R4(config-if)#int fa 0/0pv rip R4Rip en R4(config-if)#^Z R4# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#int s 1/1 R2(config-if)#ipv rip R2Rip en R2(config-if)#^Z R2# *Mar 1 06:09:43.135: %SYS-5-CONFIG_I: Configured from console by console R2#sh ipv route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::1, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R2#p 2000:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/36/44 ms R2#sh ip v      run | ipv   ripbrip rip ipv6 rip R2Rip enable ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 address FE80::2 link-local clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown --More--  ! interface Serial1/7 no ip address shutdown ! ip classless ! no ip http server no ip http secure-server ! ipv6 router rip R2Rip ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 --More--   R2#sh run | b 1/1 interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ipv6 address FE80::2 link-local ipv6 rip R2Rip enable ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 address FE80::2 link-local clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown --More--   R2# RACK98AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh run i | b 0/1 interface Ethernet0/1 no ip address half-duplex ipv6 address 2005:0:104::1/64 ipv6 address FE80::1 link-local ipv6 rip R1Rip enable ! interface Serial0/1 no ip address ipv6 address 2005:0:102::1/64 ipv6 address FE80::1 link-local ipv6 rip R1Rip enable clock rate 64000 ! router rip version 2 network 180.40.0.0 no auto-summary ! no ip http server ip classless ! ! --More--   R1# RACK98AS>4 [Resuming connection 4 to r4 ... ] * R4#sh rub n | b Lo interface Loopback0 no ip address ipv6 address 2000:4:4::/64 ipv6 rip R4Rip enable ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2005:0:104::4/64 ipv6 address FE80::4 link-local ipv6 rip R4Rip enable ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! no ip http server no ip http secure-server ip classless ! ! --More--   R4# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipv router rtip      rip R1Rip R1(config-rtr)#distr R1(config-rtr)#distribute-list ? prefix-list Filter connections based on an IPv6 prefix-list R1(config-rtr)#distribute-list                 exit R1(config)#ipv R1(config)#ipv6 pe re R1(config)#ipv6 prefix-list ? WORD Name of a prefix list sequence-number Include/exclude sequence numbers in NVGEN R1(config)#ipv6 prefix-list Prob3 ? deny Specify packets to reject description Prefix-list specific description permit Specify packets to forward seq sequence number of an entry R1(config)#ipv6 prefix-list Prob3 den 2000:4:4::/64 R1(config)#ipv6 prefix-list Prob3 den 2000:4:4::/64                 an    per any ^ % Invalid input detected at '^' marker. R1(config)#ipv6 prefix-list Prob3 per any   ::/0 ge ? <0-128> Minimum prefix length R1(config)#ipv6 prefix-list Prob3 per ::/0 ge    le 128 R1(config)#ipv6 prefix-list Prob3 per ::/0 le 128any den 2000:4:4::/64exit ipv router rip R1Rip R1(config-rtr)#di ri R1(config-rtr)#dri  ist R1(config-rtr)#distr R1(config-rtr)#distribute-list p R1(config-rtr)#distribute-list prefix-list Prob3 ? in out R1(config-rtr)#distribute-list prefix-list Prob3 out ? Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface Ethernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R1(config-rtr)#distribute-list prefix-list Prob3 out ser 1 0/1 R1(config-rtr)#^Z R1# *Mar 1 06:15:16.490: %SYS-5-CONFIG_I: Configured from console by console R1# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2#shi  ipv route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::1, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   R2#clea ipv rout * R2#clea ipv rout *sh ipv route  IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:4:4::/64 [120/3] via FE80::1, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   R2#sh ipv ro ip data RIP process "R2Rip", local RIB 2000:4:4::/64, metric 3, installed Serial1/1/FE80::1, expires in 121 secs 2005:0:102::/64, metric 2 Serial1/1/FE80::1, expires in 179 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::1, expires in 179 secs R2#clea ipv rip R2Rip ? R2#clea ipv rip R2Rip R2#clea ipv rip R2Rip sh ipv rip data  RIP process "R2Rip", local RIB R2#dev b ipv rip RIP Routing Protocol debugging is on R2#deb ipv ripsh ipv rip data RIP process "R2Rip", local RIB 2005:0:102::/64, metric 2 Serial1/1/FE80::1, expires in 174 secs 2005:0:104::/64, metric 2, installed Serial1/1/FE80::1, expires in 174 secs R2# *Mar 1 06:15:31.726: RIPng: Sending multicast update on Serial1/1 for R2Rip *Mar 1 06:15:31.726: src=FE80::2 *Mar 1 06:15:31.726: dst=FF02::9 (Serial1/1) *Mar 1 06:15:31.726: sport=521, dport=521, length=32 *Mar 1 06:15:31.726: command=2, version=1, mbz=0, #rte=1 *Mar 1 06:15:31.726: tag=0, metric=1, prefix=2005:0:102::/64 R2#u all All possible debugging has been turned off R2#sh ipv route IPv6 Routing Table - 11 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 L 2005:0:1203::2/128 [0/0] --More--   R2# RACK98AS>4 [Resuming connection 4 to r4 ... ] R4# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1#sh run|  | b ipv6 router ipv6 router rip R1Rip distribute-list prefix-list Prob3 out Serial0/1 ! ! ! ipv6 prefix-list Prob3 seq 5 deny 2000:4:4::/64 ipv6 prefix-list Prob3 seq 10 permit ::/0 le 128 ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1# R1# R1# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#int s 1/2 R2(config-if)#ipv ospf 1 area 20 R2(config-if)# *Mar 1 06:18:43.124: %OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id, please configure manually R2(config-if)#rou   ipv router ospf 1 R2(config-rtr)#rout R2(config-rtr)#router-id 0.0.0.2 R2(config-rtr)#do sh run int s 1/2 Building configuration... Current configuration : 146 bytes ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 20 clock rate 64000 end R2(config-rtr)#^Z R2# *Mar 1 06:19:04.651: %SYS-5-CONFIG_I: Configured from console by console R2# RACK98AS>3 [Resuming connection 3 to r3 ... ] R3#config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ipv router ospf 1 R3(config-rtr)# *Mar 1 06:19:16.940: %OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id, please configure manually R3(config-rtr)#route R3(config-rtr)#router-id 0.0.0.3 R3(config-rtr)#int lo 0 R3(config-if)#ipv ospf 1 area 51 R3(config-if)#int s 1/2 R3(config-if)#int s 1/2pv ospf 1 area 51  20 R3(config-if)# *Mar 1 06:20:00.944: %OSPFv3-5-ADJCHG: Process 1, Nbr 0.0.0.2 on Serial1/2 from LOADING to FULL, Loading Done R3(config-if)#rout    ipv router ospf 1 R3(config-rtr)#area 20 vir R3(config-rtr)#area 20 virtual-link ? A.B.C.D RouterID associated with virtual link neighbor R3(config-rtr)#area 20 virtual-link 0.0.0.2 R3(config-rtr)#^Z R3# RACK98AS>2 [Resuming connection 2 to r2 ... ] *M R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#f ipv router ospf 1 R2(config-rtr)#area 20 vir R2(config-rtr)#area 20 virtual-link 0.0.0.3 R2(config-rtr)#^Z R2# *Mar 1 06:20:39.339: %SYS-5-CONFIG_I: Configured from console by console R2#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 0.0.0.3 1 INIT/ - 00:00:35 28 OSPF_VL0 0.0.0.3 1 FULL/ - 00:00:39 11 Serial1/2 R2# *Mar 1 06:20:48.345: %OSPFv3-5-ADJCHG: Process 1, Nbr 0.0.0.3 on OSPF_VL0 from LOADING to FULL, Loading Done R2# R2# R2# R2#sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 0.0.0.3 1 FULL/ - 00:00:31 28 OSPF_VL0 0.0.0.3 1 FULL/ - 00:00:35 11 Serial1/2 R2#sh ipv ospf iny y t OSPF_VL0 is up, line protocol is up Interface ID 29 Area 0, Process ID 1, Instance ID 0, Router ID 0.0.0.2 Network Type VIRTUAL_LINK, Cost: 781 Configured as demand circuit. Run as demand circuit. DoNotAge LSA allowed. Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:01 Index 1/1/2, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 0.0.0.3 (Hello suppressed) Suppress hello for 1 neighbor(s) Serial1/2 is up, line protocol is up Link Local Address FE80::2, Interface ID 11 Area 20, Process ID 1, Instance ID 0, Router ID 0.0.0.2 Network Type POINT_TO_POINT, Cost: 781 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 --More--   Hello due in 00:00:01 Index 1/1/1, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 1, maximum is 2 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 0.0.0.3 Suppress hello for 0 neighbor(s) R2#sh ip  v        sh ipv route IPv6 Routing Table - 13 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/2 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::2/128 [0/0] via ::, Serial1/0.2 C 2005:0:1203::/64 [0/0] --More--   R2#sh ipv ospf data OSPFv3 Router with ID (0.0.0.2) (Process ID 1) Router Link States (Area 0) ADV Router Age Seq# Fragment ID Link count Bits 0.0.0.2 106 0x80000002 0 1 B 0.0.0.3 1 (DNA) 0x80000003 0 1 B Inter Area Prefix Link States (Area 0) ADV Router Age Seq# Prefix 0.0.0.2 117 0x80000001 2005:0:1203::/64 0.0.0.2 117 0x80000001 2005:0:1203::3/128 0.0.0.2 107 0x80000001 2005:0:1203::2/128 0.0.0.3 5 (DNA) 0x80000001 2005:0:1203::/64 0.0.0.3 5 (DNA) 0x80000001 2005:0:1203::2/128 0.0.0.3 5 (DNA) 0x80000001 2005:0:1203::3/128 0.0.0.3 5 (DNA) 0x80000001 2000:3:3::/128 Link (Type-8) Link States (Area 0) ADV Router Age Seq# Link ID Interface --More--   R2#ping 2000:3:3:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:3:3::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms R2# R2# R2# R2# R2#sh run | b 1/2 interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 20 clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! --More--  interface Serial1/7 no ip address shutdown ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 0.0.0.2 log-adjacency-changes area 20 virtual-link 0.0.0.3 ! ipv6 router rip R2Rip ! ! ! ! ! ! ! ! --More--   R2# RACK98AS>3 [Resuming connection 3 to r3 ... ] *M R3#sh run | b Lo interface Loopback0 no ip address ipv6 address 2000:3:3::/64 ipv6 ospf 1 area 51 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay --More--   ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::3/64 ipv6 address FE80::3 link-local ipv6 ospf 1 area 20 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! --More--  interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! ip classless ! no ip http server no ip http secure-server ! ipv6 router ospf 1 router-id 0.0.0.3 log-adjacency-changes area 20 virtual-link 0.0.0.2 ! ! --More--   R3# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2#confi gt  t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#confi gt ^ % Invalid input detected at '^' marker. R2(config)#a;sndf;awjhdfpiuahsdfpuhasdf ^ % Invalid input detected at '^' marker. R2(config)#rou   ipv router er  rip R2Rip R2(config-rtr)#red R2(config-rtr)#redistribute ? bgp Border Gateway Protocol (BGP) connected Connected Routes isis ISO IS-IS ospf Open Shortest Path First (OSPF) rip IPv6 Routing Information Protocol (RIPv6) static Static Routes R2(config-rtr)#redistribute ospf ? <1-65535> Process ID R2(config-rtr)#redistribute ospf 1 ? match Redistribution of OSPF routes metric Metric for redistributed routes route-map Route map reference R2(config-rtr)#redistribute ospf 1 me R2(config-rtr)#redistribute ospf 1 metric ? <0-16> Default metric transparent Transparently redistribute metric R2(config-rtr)#redistribute ospf 1 metric 1 2 R2(config-rtr)# RACK98AS> [Resuming connection 2 to r2 ... ] R2(config-rtr)# R2(config-rtr)#ipv router ospf 1 R2(config-rtr)#redi R2(config-rtr)#redistribute rip ? WORD User selected string identifying this process R2(config-rtr)#redistribute rip R2Rip ? metric Metric for redistributed routes metric-type OSPF/IS-IS exterior metric type for redistributed routes route-map Route map reference tag Set tag for routes redistributed into OSPF R2(config-rtr)#redistribute rip R2Rip R2(config-rtr)# RACK98AS>3 [Resuming connection 3 to r3 ... ] R3#sh ipv route IPv6 Routing Table - 10 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3::/128 [0/0] via ::, Loopback0 OE2 2005:0:104::/64 [110/20] via FE80::2, Serial1/2 C 2005:0:237::/64 [0/0] via ::, Serial1/0 L 2005:0:237::3/128 [0/0] via ::, Serial1/0 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203::2/128 [110/781] via FE80::2, Serial1/2 L 2005:0:1203::3/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] --More--   via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R3#ping 2005:0:104::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 60/73/96 ms R3# RACK98AS>4 [Resuming connection 4 to r4 ... ] R4#sh ipv route IPv6 Routing Table - 9 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::/128 [120/4] via FE80::1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::/128 [0/0] via ::, Loopback0 R 2005:0:102::/64 [120/2] via FE80::1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:1203::3/128 [120/4] via FE80::1, FastEthernet0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] --More--   via ::, Null0 R4# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2(config-rtr)#redis R2(config-rtr)#redistribute con R2(config-rtr)#redistribute connected R2(config-rtr)#redistribute connected rip R2Rip ipv router ospf 1 redistribute rip R2Rip ipv router ospf 1 redistribute ospf 1 metric 2ipv router rip R2Rip  R2(config-rtr)#ipv router rip R2Ripredistribute connected R2(config-rtr)#^Z R2# RACK98AS>3 [Resuming connection 3 to r3 ... ] R3#sh ipv route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2000:3:3::/64 [0/0] via ::, Loopback0 L 2000:3:3::/128 [0/0] via ::, Loopback0 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/2 OE2 2005:0:104::/64 [110/20] via FE80::2, Serial1/2 C 2005:0:237::/64 [0/0] via ::, Serial1/0 L 2005:0:237::3/128 [0/0] via ::, Serial1/0 OE2 2005:0:702::/64 [110/20] via FE80::2, Serial1/2 C 2005:0:1203::/64 [0/0] via ::, Serial1/2 O 2005:0:1203::2/128 [110/781] --More--   via FE80::2, Serial1/2 L 2005:0:1203::3/128 [0/0] via ::, Serial1/2 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R3# RACK98AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip  v route IPv6 Routing Table - 12 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 R 2000:3:3::/128 [120/4] via FE80::1, FastEthernet0/0 C 2000:4:4::/64 [0/0] via ::, Loopback0 L 2000:4:4::/128 [0/0] via ::, Loopback0 R 2005:0:102::/64 [120/2] via FE80::1, FastEthernet0/0 C 2005:0:104::/64 [0/0] via ::, FastEthernet0/0 L 2005:0:104::4/128 [0/0] via ::, FastEthernet0/0 R 2005:0:237::/64 [120/3] via FE80::1, FastEthernet0/0 R 2005:0:702::/64 [120/3] via FE80::1, FastEthernet0/0 R 2005:0:1203::/64 [120/3] --More--   via FE80::1, FastEthernet0/0 R 2005:0:1203::3/128 [120/4] via FE80::1, FastEthernet0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R4# RACK98AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh run | b router ipv6 router ospf 1 router-id 0.0.0.2 log-adjacency-changes area 20 virtual-link 0.0.0.3 redistribute connected redistribute rip R2Rip ! ipv6 router rip R2Rip redistribute connected redistribute ospf 1 metric 2 ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous --More--   R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#int s 1/0.1 R2(config-subif)#ip ospf v ospf  ospf 1 area 0 R2(config-subif)#ipv ospf 1 area 0nt s 1/0.1  2 R2(config-subif)#int s 1/0.2pv ospf 1 area 0 R2(config-subif)#^Z R2# RACK98AS>7 [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int s 1/0.1 R7(config-subif)#ip  eix  xit R7(config)#ipv router osp[f    f 1 R7(config-rtr)#rout R7(config-rtr)#router-id 0.0.0.67  7 R7(config-rtr)#int s 1/0.1 R7(config-subif)#ipv ospf 1 area 0 R7(config-subif)#ipv ospf 1 area 0nt s 1/0.1  2 R7(config-subif)#int s 1/0.2pv ospf 1 area 0 R7(config-subif)#^Z R7# RACK98AS>3 [Resuming connection 3 to r3 ... ] R3#confi gt ^ % Invalid input detected at '^' marker. R3#coni n fig t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/0 R3(config-if)#ipv ospf 1 area 0 R3(config-if)#do sh ipv ospf int s 1/0 Serial1/0 is up, line protocol is up Link Local Address FE80::3, Interface ID 9 Area 0, Process ID 1, Instance ID 0, Router ID 0.0.0.3 Network Type NON_BROADCAST, Cost: 781 Transmit Delay is 1 sec, State WAITING, Priority 1 No designated router on this network No backup designated router on this network Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 Hello due in 00:00:11 Wait time before Designated router selection 00:01:41 Index 1/2/4, flood queue length 0 Next 0x0(0)/0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) R3(config-if)#ipv ospf net R3(config-if)#ipv ospf network ? broadcast Specify OSPF broadcast multi-access network non-broadcast Specify OSPF NBMA network point-to-multipoint Specify OSPF point-to-multipoint network point-to-point Specify OSPF point-to-point network R3(config-if)#ipv ospf network po R3(config-if)#ipv ospf network point-to-m R3(config-if)#ipv ospf network point-to-multipoint R3(config-if)#ipv ospf hell R3(config-if)#ipv ospf hello-interval ? <1-65535> Seconds R3(config-if)#ipv ospf hello-interval 10 R3(config-if)#do sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 0.0.0.7 1 EXCHANGE/ - 00:00:38 27 Serial1/0 0.0.0.2 1 EXSTART/ - 00:00:38 27 Serial1/0 0.0.0.2 1 FULL/ - - 29 OSPF_VL0 0.0.0.2 1 FULL/ - 00:00:35 11 Serial1/2 R3(config-if)#do sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 0.0.0.7 1 EXCHANGE/ - 00:00:36 27 Serial1/0 0.0.0.2 1 EXSTART/ - 00:00:39 27 Serial1/0 0.0.0.2 1 FULL/ - - 29 OSPF_VL0 0.0.0.2 1 FULL/ - 00:00:38 11 Serial1/2 R3(config-if)#do sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 0.0.0.7 1 EXCHANGE/ - 00:00:35 27 Serial1/0 0.0.0.2 1 EXSTART/ - 00:00:37 27 Serial1/0 0.0.0.2 1 FULL/ - - 29 OSPF_VL0 0.0.0.2 1 FULL/ - 00:00:36 11 Serial1/2 R3(config-if)#do sh ipv ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 0.0.0.7 1 EXCHANGE/ - 00:00:38 27 Serial1/0 0.0.0.2 1 EXSTART/ - 00:00:38 27 Serial1/0 0.0.0.2 1 FULL/ - - 29 OSPF_VL0 0.0.0.2 1 FULL/ - 00:00:35 11 Serial1/2 R3(config-if)#do deb fram pack Frame Relay packet debugging is on R3(config-if)#do u all *Mar 1 06:31:22.048: Serial1/0(i): dlci 302(0x48E1), pkt type 0x86DD, datagramsize 84 R3(config-if)#do u all *Mar 1 06:31:24.308: Serial1/0:Encaps failed--no map entry link 79(IPV6) *Mar 1 06:31:24.336: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 72 *Mar 1 06:31:24.336: Serial1/0:Encaps failed--no map entry link 79(IPV6) *Mar 1 06:31:24.348: Serial1/0(i): dlci 302(0x48E1), pkt type 0x86DD, datagramsize 72 *Mar 1 06:31:24.436: Serial1/0(i): dlci 307(0x4C31), pkt type 0x86DD, datagramsize 84 R3(config-if)#do u all All possible debugging has been turned off R3(config-if)#fram map ipv fe80::7 307 R3(config-if)#fram map ipv fe80::7 307 2 302 2 302 *Mar 1 06:31:59.726: %OSPFv3-5-ADJCHG: Process 1, Nbr 0.0.0.7 on Serial1/0 from LOADING to FULL, Loading Done R3(config-if)#fram map ipv fe80::2 302 R3(config-if)# *Mar 1 06:32:04.818: %OSPFv3-5-ADJCHG: Process 1, Nbr 0.0.0.2 on Serial1/0 from LOADING to FULL, Loading Done R3(config-if)#^Z R3# *Mar 1 06:32:08.444: %SYS RACK98AS>7 [Resuming connection 7 to r7 ... ] * R7#sh ipv route IPv6 Routing Table - 13 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/1562] via FE80::2, Serial1/0.2 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20] via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/1562] via FE80::2, Serial1/0.2 L 2005:0:237::7/128 [0/0] via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] --More--   via FE80::2, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::2, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#ping 2005:0:104::4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:104::4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/96/125 ms R7#^x2 % Unknown command or computer name, or unable to find computer address R7# R7# RACK98AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh run ] |   | b 1/0.1 interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 203 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 207 ! interface Serial1/1 no ip address ipv6 address 2005:0:102::2/64 ipv6 address FE80::2 link-local ipv6 rip R2Rip enable ! interface Serial1/2 no ip address ipv6 address 2005:0:1203::2/64 ipv6 address FE80::2 link-local ipv6 ospf 1 area 20 --More--   R2# RACK98AS>3 [Resuming connection 3 to r3 ... ] -5-CONFIG_I: Configured from console by console R3# R3#sh run |     int s 1/0 Building configuration... Current configuration : 389 bytes ! interface Serial1/0 no ip address encapsulation frame-relay ipv6 address 2005:0:237::3/64 ipv6 address FE80::3 link-local ipv6 ospf network point-to-multipoint ipv6 ospf hello-interval 10 ipv6 ospf 1 area 0 frame-relay map ipv6 FE80::2 302 frame-relay map ipv6 FE80::7 307 frame-relay map ipv6 2005:0:237::2 302 broadcast frame-relay map ipv6 2005:0:237::7 307 broadcast end R3# R3# RACK98AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | v b 1/0.`1  1 interface Serial1/0.1 point-to-point ipv6 address 2005:0:237::7/64 ipv6 address FE80::7 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 703 ! interface Serial1/0.2 point-to-point ipv6 address 2005:0:702::7/64 ipv6 address FE80::7 link-local ipv6 ospf 1 area 0 frame-relay interface-dlci 702 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown --More--   R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int tu 0 R7(config-if)#ipv *Mar 1 06:34:07.944: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R7(config-if)#ipv ad  d R7(config-if)#ipv address 2005:0:17::7/64 R7(config-if)#tun sou fa 0/1 R7(config-if)#tun des 180.40.7.66 R7(config-if)# *Mar 1 06:34:45.578: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R7(config-if)#ipv rip R7Rip en R7(config-if)#^Z R7# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1#confi gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0 R1(config-if)# *Mar 1 06:36:14.332: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#ipv add 2005:0:17::1/64 R1(config-if)#tun sou e 0/0 R1(config-if)#tun det   st 180.40.7.1 R1(config-if)# *Mar 1 06:36:52.274: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-if)#^Z R1#conf *Mar 1 06:36:55.087: %SYS-5-CONFIG_I: Configured from console by console R1#confi gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0 R1(config-if)#ipv rip R1Rip en R1(config-if)#^Z R1# RACK98AS>7 [Resuming connection 7 to r7 ... ] * R7#sh ipv route IPv6 Routing Table - 16 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/0.1 R 2000:4:4::/64 [120/3] via FE80::201:96FF:FEA1:BD20, Tunnel0 C 2005:0:17::/64 [0/0] via ::, Tunnel0 L 2005:0:17::7/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20] via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] --More--   via ::, Serial1/0.1 C 2005:0:702::/64 [0/0] via ::, Serial1/0.2 L 2005:0:702::7/128 [0/0] via ::, Serial1/0.2 OI 2005:0:1203::/64 [110/1562] via FE80::2, Serial1/0.2 via FE80::3, Serial1/0.1 OI 2005:0:1203::2/128 [110/781] via FE80::2, Serial1/0.2 OI 2005:0:1203::3/128 [110/781] via FE80::3, Serial1/0.1 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 R7#p 2000:4:4:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2000:4:4::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R7# RACK98AS>1 [Resuming connection 1 to r1 ... ] *M R1#sh run int tui    0 Building configuration... Current configuration : 151 bytes ! interface Tunnel0 no ip address ipv6 address 2005:0:17::1/64 ipv6 rip R1Rip enable tunnel source Ethernet0/0 tunnel destination 180.40.7.1 end R1#^x  sh     RACK98AS>7 [Resuming connection 7 to r7 ... ] R7#sh run tun 0 ^ % Invalid input detected at '^' marker. R7#sh run tun 0itun 0ntun 0ttun 0 tun 0 Building configuration... Current configuration : 156 bytes ! interface Tunnel0 no ip address ipv6 address 2005:0:17::7/64 ipv6 rip R7Rip enable tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 end R7# R7#sh int tu 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source 180.40.7.1 (FastEthernet0/1), destination 180.40.7.66 Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled Tunnel TTL 255 Checksumming of packets disabled, fast tunneling enabled Last input 00:00:03, output 00:00:12, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 14 packets input, 2172 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 17 packets output, 1740 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R7# R7#confi g  Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int tu 0 R7(config-if)#tun mode ip R7(config-if)#tun mode ipv R7(config-if)#tun mode ipv6ip R7(config-if)#^Z R7# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0 R1(config-if)#i mode      tun mode ipv R1(config-if)#tun mode ipv6ip R1(config-if)#^Z R1# *Mar 1 06:40:03.940: %SYS-5-CONFIG_I: Configured from console by console R1#sh int tu 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source 180.40.7.66 (Ethernet0/0), destination 180.40.7.1 Tunnel protocol/transport IPv6/IP, key disabled, sequencing disabled Tunnel TTL 255 Checksumming of packets disabled, fast tunneling enabled Last input 00:00:28, output 00:00:06, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 12 packets input, 1292 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 20 packets output, 3436 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R1#ping 2005:0:17::7 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2005:0:17::7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms R1#sh rt un int tu 0 Building configuration... Current configuration : 171 bytes ! interface Tunnel0 no ip address ipv6 address 2005:0:17::1/64 ipv6 rip R1Rip enable tunnel source Ethernet0/0 tunnel destination 180.40.7.1 tunnel mode ipv6ip end R1# RACK98AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh run int tu 0 Building configuration... Current configuration : 176 bytes ! interface Tunnel0 no ip address ipv6 address 2005:0:17::7/64 ipv6 rip R7Rip enable tunnel source FastEthernet0/1 tunnel destination 180.40.7.66 tunnel mode ipv6ip end R7#sh int tu 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source 180.40.7.1 (FastEthernet0/1), destination 180.40.7.66 Tunnel protocol/transport IPv6/IP, key disabled, sequencing disabled Tunnel TTL 255 Checksumming of packets disabled, fast tunneling enabled Last input 00:00:13, output 00:00:20, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 24 packets input, 4112 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 29 packets output, 2976 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R7# R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#int tu 0 R7(config-if)#no tun dest R7(config-if)#no ipv add 2005:0:17::7/64 R7(config-if)# *Mar 1 06:41:07.961: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R7(config-if)#no ipv add 2005:0:17::7/64tun dest int tu 0 tun mode ipv6ip 6 R7(config-if)#tun mode ipv6ip 6to4 R7(config-if)# *Mar 1 06:41:17.592: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R7(config-if)#ipv add 2002:b428:701  ::/64 R7(config-if)#exit R7(config)#ipv route R7(config)#ipv route ? X:X:X:X::X/<0-128> IPv6 prefix x:x::y/ R7(config)#ipv route 2002::/16 tun 0 R7(config)# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1#confi gt ^ % Invalid input detected at '^' marker. R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int tu 0 R1(config-if)#no tun dest 180.40.7.1 R1(config-if)#tun mode *Mar 1 06:45:14.517: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R1(config-if)#tun mode ipv R1(config-if)#tun mode ipv6ip 6 R1(config-if)#tun mode ipv6ip 6to4 R1(config-if)#ip  *Mar 1 06:45:20.391: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R1(config-if)#i no ipv add 2005:0:17::1/64 R1(config-if)#ipv add 2002:b412  28:742::/64 R1(config-if)#exit R1(config)#ipv route 2002::/16 tun 0 R1(config)#ipv router rip R2 1Rip R1(config-rtr)#nei R1(config-rtr)#nei? % Unrecognized command R1(config-rtr)#nei   ? default Set a command to its defaults distance Administrative distance distribute-list Filter networks in routing updates exit Exit from IPv6 routing protocol configuration mode maximum-paths Forward packets over multiple paths no Negate a command or set its defaults poison-reverse Poison reverse updates port Port and multicast address redistribute Redistribute IPv6 prefixes from another routing protocol split-horizon Split horizon updates summary-prefix Configure IPv6 summary prefix timers Adjust routing timers R1(config-rtr)#int tu 0 R1(config-if)#ipv rip ? WORD User selected string identifying this RIP process R1(config-if)#ipv rip R1Rip ? default-information Configure handling of default route enable Enable/disable RIP routing metric-offset Adjust default metric increment summary-address Configure address summarization R1(config-if)#ipv rip R1Rip               ^Z R1# RACK98AS>7 [Resuming connection 7 to r7 ... ] R7(config)#^Z R7#sh ipv r *Mar 1 06:45:50.896: %SYS-5-CONFIG_I: Configured from console by console R7#sh ipv route IPv6 Routing Table - 19 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/0.1 R 2000:4:4::/64 [120/3] via FE80::B428:742, Tunnel0 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 OE2 2002:B428:742::/64 [110/20] via FE80::2, Serial1/0.2 R 2005:0:17::/64 [120/2] via FE80::B428:742, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20] --More--   R7#sh ipv route     rip data RIP process "R7Rip", local RIB 2000:3:3::/128, metric 4 Tunnel0/FE80::B428:742, expires in 74 secs 2000:4:4::/64, metric 3, installed Tunnel0/FE80::B428:742, expires in 74 secs 2005:0:17::/64, metric 2, installed Tunnel0/FE80::B428:742, expires in 74 secs 2005:0:102::/64, metric 2 Tunnel0/FE80::B428:742, expires in 74 secs 2005:0:104::/64, metric 2 Tunnel0/FE80::B428:742, expires in 74 secs 2005:0:237::3/128, metric 4 Tunnel0/FE80::B428:742, expires in 74 secs 2005:0:237::/64, metric 3 Tunnel0/FE80::B428:742, expires in 74 secs 2005:0:702::/64, metric 3 Tunnel0/FE80::B428:742, expires in 74 secs 2005:0:1203::3/128, metric 4 Tunnel0/FE80::B428:742, expires in 74 secs 2005:0:1203::/64, metric 3 Tunnel0/FE80::B428:742, expires in 74 secs R7#deb ipv route    rip ^ % Invalid input detected at '^' marker. R7#deb ipv rripip  RIP Routing Protocol debugging is on R7#confi gt ^ % Invalid input detected at '^' marker. R7#confi gt  t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ipv router ospf 1 R7(config-rtr)#nei R7(config-rtr)#nei? % Unrecognized command R7(config-rtr)#nei *Mar 1 06:46:30.630: RIPng: Sending multicast update on Tunnel0 for R7Rip *Mar 1 06:46:30.630: src=FE80::B428:701 *Mar 1 06:46:30.630: dst=FF02::9 (Tunnel0) *Mar 1 06:46:30.630: sport=521, dport=521, length=32 *Mar 1 06:46:30.630: command=2, version=1, mbz=0, #rte=1 *Mar 1 06:46:30.630: tag=0, metric=1, prefix=2002:B428:701::/64 R7(config-rtr)#nei   ? area OSPF area parameters auto-cost Calculate OSPF interface cost according to bandwidth default Set a command to its defaults default-information Distribution of default information default-metric Set metric of redistributed routes discard-route Enable or disable discard-route installation distance Administrative distance distribute-list Filter networks in routing updates exit Exit from IPv6 routing protocol configuration mode ignore Do not complain about specific event log-adjacency-changes Log changes in adjacency state maximum-paths Forward packets over multiple paths no Negate a command or set its defaults passive-interface Suppress routing updates on an interface redistribute Redistribute IPv6 prefixes from another routing protocol router-id router-id for this OSPF process summary-prefix Configure IPv6 summary prefix timers Adjust routing timers R7(config-rtr)#q int s 1/0.1 R7(config-subif)#ipv ospf ? <1-65535> Process ID cost Interface cost database-filter Filter OSPF LSA during synchronization and flooding dead-interval Interval after which a neighbor is declared dead demand-circuit OSPF demand circuit flood-reduction OSPF Flood Reduction hello-interval Time between HELLO packets mtu-ignore Ignores the MTU in DBD packets neighbor OSPF neighbor network Network type priority Router priority retransmit-interval Time between retransmitting lost link state advertisements transmit-delay Link state transmit delay R7(config-subif)#ipv ospf nei R7(config-subif)#ipv ospf neighbor *Mar 1 06:46:57.313: RIPng: Sending multicast update on Tunnel0 for R7Rip *Mar 1 06:46:57.313: src=FE80::B428:701 *Mar 1 06:46:57.313: dst=FF02::9 (Tunnel0) *Mar 1 06:46:57.313: sport=521, dport=521, length=32 *Mar 1 06:46:57.313: command=2, version=1, mbz=0, #rte=1 *Mar 1 06:46:57.313: tag=0, metric=1, prefix=2002:B428:701::/64 R7(config-subif)#ipv ospf neighbor *Mar 1 06:47:14.694: RIPng: 2000:3:3::/128, expired, ttg is 0 *Mar 1 06:47:14.694: RIPng: Deleting 2000:3:3::/128 *Mar 1 06:47:14.694: RIPng: 2000:4:4::/64, expired, ttg is 120 *Mar 1 06:47:14.694: RIPng: 2005:0:17::/64, expired, ttg is 120 *Mar 1 06:47:14.694: RIPng: 2005:0:102::/64, expired, ttg is 0 *Mar 1 06:47:14.694: RIPng: Deleting 2005:0:102::/64 *Mar 1 06:47:14.694: RIPng: 2005:0:104::/64, expired, ttg is 0 *Mar 1 06:47:14.694: RIPng: Deleting 2005:0:104::/64 *Mar 1 06:47:14.698: RIPng: 2005:0:237::3/128, expired, ttg is 0 *Mar 1 06:47:14.698: RIPng: Deleting 2005:0:237::3/128 *Mar 1 06:47:14.698: RIPng: 2005:0:237::/64, expired, ttg is 0 R7(config-subif)#ipv ospf neighbor *Mar 1 06:47:14.698: RIPng: Deleting 2005:0:237::/64 *Mar 1 06:47:14.698: RIPng: 2005:0:702::/64, expired, ttg is 0 *Mar 1 06:47:14.698: RIPng: Deleting 2005:0:702::/64 *Mar 1 06:47:14.698: RIPng: 2005:0:1203::3/128, expired, ttg is 0 *Mar 1 06:47:14.698: RIPng: Deleting 2005:0:1203::3/128 *Mar 1 06:47:14.698: RIPng: 2005:0:1203::/64, expired, ttg is 0 *Mar 1 06:47:14.702: RIPng: Deleting 2005:0:1203::/64 *Mar 1 06:47:14.702: RIPng: Triggered update requested *Mar 1 06:47:14.702: RIPng: Next RIB walk in 2000 R7(config-subif)#ipv ospf neighbor *Mar 1 06:47:15.704: RIPng: generating triggered update for R7Rip *Mar 1 06:47:15.704: RIPng: Suppressed null multicast update on Tunnel0 for R7Rip *Mar 1 06:47:16.701: RIPng: Next RIB walk in 117992 R7(config-subif)#ipv ospf neighbor   *Mar 1 06:47:24.923: RIPng: Sending multicast update on Tunnel0 for R7Rip *Mar 1 06:47:24.923: src=FE80::B428:701 *Mar 1 06:47:24.923: dst=FF02::9 (Tunnel0) *Mar 1 06:47:24.923: sport=521, dport=521, length=32 *Mar 1 06:47:24.923: command=2, version=1, mbz=0, #rte=1 *Mar 1 06:47:24.923: tag=0, metric=1, prefix=2002:B428:701::/64 R7(config-subif)#ipv ospf neighbor                 ^Z R7#u all All possible debugging has been turned off R7# *Mar 1 06:47:28.156: %SYS-5-CONFIG_I: Configured from console by console R7#ping 2002:b47 28:72 42:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:742::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 84/93/112 ms R7# R7# R7# R7#sh ip  v route IPv6 Routing Table - 17 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/0.1 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 OE2 2002:B428:742::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20] via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] --More--   R7# RACK98AS>1 [Resuming connection 1 to r1 ... ] *M R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#int tu 0 R1(config-if)#no ipv rip R1Rip en R1(config-if)#^Z R1# *Mar 1 06:49:28.606: %SYS-5-CONFIG_I: Configured from console by console R1# RACK98AS>2 [Resuming connection 2 to r2 ... ] R2#sh ipv route IPv6 Routing Table - 15 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/2 via FE80::3, Serial1/0.1 R 2002:B428:742::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:102::/64 [0/0] via ::, Serial1/1 L 2005:0:102::2/128 [0/0] via ::, Serial1/1 R 2005:0:104::/64 [120/2] via FE80::1, Serial1/1 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 L 2005:0:237::2/128 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/2 --More--   R2#clea ipv   rip data % No such RIPv6 instance R2#clea ipv rip data    R2Rip R2#^Z R2# RACK98AS>7 [Resuming connection 7 to r7 ... ] R7#sh ipv route IPv6 Routing Table - 16 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 OI 2000:3:3::/128 [110/781] via FE80::3, Serial1/0.1 S 2002::/16 [1/0] via ::, Tunnel0 C 2002:B428:701::/64 [0/0] via ::, Tunnel0 L 2002:B428:701::/128 [0/0] via ::, Tunnel0 OE2 2005:0:102::/64 [110/20] via FE80::2, Serial1/0.2 OE2 2005:0:104::/64 [110/20] via FE80::2, Serial1/0.2 C 2005:0:237::/64 [0/0] via ::, Serial1/0.1 O 2005:0:237::3/128 [110/781] via FE80::3, Serial1/0.1 L 2005:0:237::7/128 [0/0] --More--   R7#sh ipv routeping 2002:b428:742:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:742::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms R7# RACK98AS>1 [Resuming connection 1 to r1 ... ] R1#sh run        p 2002:b428:701  01:: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2002:B428:701::, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms R1#shj    run |     | int tu 0 Building configuration... Current configuration : 142 bytes ! interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:742::/64 tunnel source Ethernet0/0 tunnel mode ipv6ip 6to4 end R1# R1# RACK98AS>7 [Resuming connection 7 to r7 ... ] R7#sh run int tu 0 Building configuration... Current configuration : 169 bytes ! interface Tunnel0 no ip address no ip redirects ipv6 address 2002:B428:701::/64 ipv6 rip R7Rip enable tunnel source FastEthernet0/1 tunnel mode ipv6ip 6to4 end R7# R7#sh run | u i ipv6 route          2002::/  ipv6 route 2002::/16 Tunnel0 R7#conf t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#ipv route 2000:4:4::/64 2002:b4287 :742:: R7(config)#ipv route 2000:4:4::/64 2002:b428:742::nipv route 2000:4:4::/64 2002:b428:742::oipv route 2000:4:4::/64 2002:b428:742:: ipv route 2000:4:4::/64 2002:b428:742:: R7(config)#^Z R7#s *Mar 1 06:57:20.583: %SYS-5-CONFIG_I: Configured from console by console R7#sh run     int tu 0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source 180.40.7.1 (FastEthernet0/1), destination UNKNOWN Tunnel protocol/transport IPv6 6to4, key disabled, sequencing disabled Checksumming of packets disabled Last input 00:05:22, output 00:00:15, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 44 packets input, 8432 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 77 packets output, 7676 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out R7# R7# R7#