=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.11.02 10:54:52 =~=~=~=~=~=~=~=~=~=~=~=
RACK98AS>7
[Resuming connection 7 to r7 ... ]
R7#config t
Enter configuration commands, one per line. End with CNTL/Z.
R7(config)#int fa 0/1
R7(config-if)#gl
R7(config-if)#glbp ?
<0-1023> Group number
R7(config-if)#glbp 47 ?
authentication Authentication method
forwarder Forwarder configuration
ip Enable group and set virtual IP address
load-balancing Load balancing method
preempt Overthrow lower priority designated routers
priority Priority level
timers Adjust GLBP timers
weighting Gateway weighting and tracking
R7(config-if)#glbp 47 ip ?
A.B.C.D Virtual IP address
<cr>
R7(config-if)#glbp 47 ip 180.40.7.134 ?
secondary Make this IP address a secondary address
<cr>
R7(config-if)#glbp 47 ip 180.40.7.134
R7(config-if)#
*Mar 1 22:19:37.940: %GLBP-6-STATECHANGE: FastEthernet0/1 Grp 47 state Standby -> Active
R7(config-if)#
*Mar 1 22:19:47.941: %GLBP-6-FWDSTATECHANGE: FastEthernet0/1 Grp 47 Fwd 1 state Listen -> Active
R7(config-if)#
R7(config-if)#
R7(config-if)#
R7(config-if)#
R7(config-if)#
RACK98AS>3
[Resuming connection 3 to r3 ... ]
R3#config t
Enter configuration commands, one per line. End with CNTL/Z.
R3(config)#ip in fa 0/0
R3(config-if)#glbp 47 oi ip 180.40.7.134
R3(config-if)#
*Mar 2 21:48:21.181: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 47 Fwd 2 state Listen -> Active
R3(config-if)#
R3(config-if)#
R3(config-if)#do sh glbp
FastEthernet0/0 - Group 47
State is Standby
1 state change, last state change 00:00:46
Virtual IP address is 180.40.7.134
Hello time 3 sec, hold time 10 sec
Next hello sent in 1.879 secs
Redirect time 600 sec, forwarder time-out 14400 sec
Preemption disabled
Active is 180.40.7.131, priority 100 (expires in 8.334 sec)
Standby is local
Priority 100 (default)
Weighting 100 (default 100), thresholds: lower 1, upper 100
Load balancing: round-robin
There are 2 forwarders (1 active)
Forwarder 1
State is Listen
MAC address is 0007.b400.2f01 (learnt)
Owner ID is 0012.7f8d.1dc1
Time to live: 14398.330 sec (maximum 14400 sec)
Preemption enabled, min delay 30 sec
Active is 180.40.7.131 (primary), weighting 100 (expires in 8.330 sec)
Forwarder 2
State is Active
--More-- 1 state change, last state change 00:01:19
MAC address is 0007.b400.2f02 (default)
Owner ID is 0012.7f8d.1ee0
Preemption enabled, min delay 30 sec
Active is local, weighting 100
R3(config-if)#exit
R3(config)#tra
R3(config)#track ?
<1-500> Tracked object
resolution Tracking resolution parameters
timer Polling interval timers
R3(config)#track ?
<1-500> Tracked object
resolution Tracking resolution parameters
timer Polling interval timers
R3(config)#track 4 ?
interface Select an interface to track
ip IP protocol
R3(config)#track 4 ip ?
route IP route
R3(config)#track 4 ip rout 20.10.1.0/24 ?
metric Route metric
reachability Route reachability state
R3(config)#track 4 ip rout 20.10.1.0/24 re
R3(config)#track 4 ip rout 20.10.1.0/24 reachability ?
<cr>
R3(config)#track 4 ip rout 20.10.1.0/24 reachability
R3(config-track)#exit
R3(config)#int fa 0/0
R3(config-if)#gl
R3(config-if)#glbp 46 7 ?
authentication Authentication method
forwarder Forwarder configuration
ip Enable group and set virtual IP address
load-balancing Load balancing method
preempt Overthrow lower priority designated routers
priority Priority level
timers Adjust GLBP timers
weighting Gateway weighting and tracking
R3(config-if)#glbp 47 weighting ?
<1-254> Weighting maximum value
track Interface tracking
R3(config-if)#glbp 47 weighting tra
R3(config-if)#glbp 47 weighting track ?
<1-500> Tracked object
R3(config-if)#glbp 47 weighting track 4 ?
decrement Weighting decrement
<cr>
R3(config-if)#glbp 47 weighting track 4 dec ?
<1-255> Decrement value
R3(config-if)#glbp 47 weighting track 4 dec 25 ?
<cr>
R3(config-if)#glbp 47 weighting track 4 dec 25
R3(config-if)#do sh glb
FastEthernet0/0 - Group 47
State is Standby
1 state change, last state change 00:04:26
Virtual IP address is 180.40.7.134
Hello time 3 sec, hold time 10 sec
Next hello sent in 0.881 secs
Redirect time 600 sec, forwarder time-out 14400 sec
Preemption disabled
Active is 180.40.7.131, priority 100 (expires in 7.344 sec)
Standby is local
Priority 100 (default)
Weighting 100 (default 100), thresholds: lower 1, upper 100
Track object 4 state Up decrement 25
Load balancing: round-robin
There are 2 forwarders (1 active)
Forwarder 1
State is Listen
MAC address is 0007.b400.2f01 (learnt)
Owner ID is 0012.7f8d.1dc1
Time to live: 14397.340 sec (maximum 14400 sec)
Preemption enabled, min delay 30 sec
Active is 180.40.7.131 (primary), weighting 100 (expires in 7.340 sec)
Forwarder 2
--More--
R3(config-if)#do sh glb glbp 47 weighting track 4 dec 25 ?
<1-254> Weighting maximum value
track Interface tracking
R3(config-if)#glbp 47 weighting 90 ?
lower Weighting lower threshold
upper Weighting upper threshold
<cr>
R3(config-if)#glbp 47 weighting 90 10 0 ?
lower Weighting lower threshold
upper Weighting upper threshold
<cr>
R3(config-if)#glbp 47 weighting 100 ?
lower Weighting lower threshold
upper Weighting upper threshold
<cr>
R3(config-if)#glbp 47 weighting 100 lower ?
<1-99> Weighting lower threshold value
R3(config-if)#glbp 47 weighting 100 lower 90 up
R3(config-if)#glbp 47 weighting 100 lower 90 upper 100 ?
<cr>
R3(config-if)#glbp 47 weighting 100 lower 90 upper 100
R3(config-if)#do sh run int s 1/0
Building configuration...
Current configuration : 251 bytes
!
interface Serial1/0
ip address 180.40.7.66 255.255.255.224
encapsulation frame-relay
ip ospf network broadcast
frame-relay map ip 180.40.7.65 307 broadcast tcp header-compression connections 20
frame-relay map ip 180.40.7.67 302 broadcast
end
R3(config-if)#do sh run int s 1/0 fa 0/0
Building configuration...
Current configuration : 441 bytes
!
interface FastEthernet0/0
ip address dhcp
ip policy route-map Prob1
duplex auto
speed auto
vrrp 47 ip 180.40.7.133
vrrp 47 priority 150
glbp 47 ip 180.40.7.134
glbp 47 weighting 100 lower 90
glbp 47 weighting track 4 decrement 25
standby 47 ip 180.40.7.132
standby 47 priority 120
standby 47 preempt
standby 47 track Serial1/0 25
standby 47 track Serial1/2 25
standby 47 track 3 decrement 25
service-policy input test
end
R3(config-if)#do sh run int fa 0/0s 1/0 glbp 47 weighting 100 lower 90 upper 100 do sh glb glbp 47 weighting track 4 dec 25 dec 25 2 dec 25
R3(config-if)#
RACK98AS>7
[Resuming connection 7 to r7 ... ]
R7(config-if)#exit
R7(config)#do sh run | i track
R7(config)#track 1 ip ?
route IP route
R7(config)#track 1 ip rou 1 20.10.1.0/25 4 re
R7(config)#track 1 ip rou 20.10.1.0/24 reachability ?
<cr>
R7(config)#track 1 ip rou 20.10.1.0/24 reachability
R7(config-track)#int fa 0/1
R7(config-if)#glbp 47 w
R7(config-if)#glbp 47 weighting 100 lo
R7(config-if)#glbp 47 weighting 100 lower 90 up 100
R7(config-if)#glbp 47 wei
R7(config-if)#glbp 47 weighting tr
R7(config-if)#glbp 47 weighting track ?
<1-500> Tracked object
R7(config-if)#glbp 47 weighting track 1 ?
decrement Weighting decrement
<cr>
R7(config-if)#glbp 47 weighting track 1 de
R7(config-if)#glbp 47 weighting track 1 decrement 25
R7(config-if)#^Z
R7#
RACK98AS>3
[Resuming connection 3 to r3 ... ]
R3(config-if)#
RACK98AS>2
[Resuming connection 2 to r2 ... ]
R2#config t
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#int s 1/2
R2(config-if)#shut
R2(config-if)#
RACK98AS>3
[Resuming connection 3 to r3 ... ]
R3(config-if)#^Z
R3#s
*Mar 2 21:57:32.401: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down
*Mar 2 21:57:32.401: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached
*Mar 2 21:57:32.826: %HSRP-6-STATECHANGE: FastEthernet0/0 Grp 47 state Active -> Speak
R3#sh g
*Mar 2 21:57:33.062: %SYS-5-CONFIG_I: Configured from console by console
*Mar 2 21:57:33.403: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down
R3#sh glbp
FastEthernet0/0 - Group 47
State is Standby
1 state change, last state change 00:09:07
Virtual IP address is 180.40.7.134
Hello time 3 sec, hold time 10 sec
Next hello sent in 1.982 secs
Redirect time 600 sec, forwarder time-out 14400 sec
Preemption disabled
Active is 180.40.7.131, priority 100 (expires in 8.533 sec)
Standby is local
Priority 100 (default)
Weighting 75, low (configured 100), thresholds: lower 90, upper 100
Track object 2 state Down decrement 25
Track object 4 state Up decrement 25
Load balancing: round-robin
There are 2 forwarders (1 active)
Forwarder 1
State is Listen
MAC address is 0007.b400.2f01 (learnt)
Owner ID is 0012.7f8d.1dc1
Time to live: 14398.533 sec (maximum 14400 sec)
Preemption enabled, min delay 30 sec
Active is 180.40.7.131 (primary), weighting 100 (expires in 8.529 sec)
--More-- Forwarder 2
State is Active
1 state change, last state change 00:09:18
MAC address is 0007.b400.2f02 (default)
Owner ID is 0012.7f8d.1ee0
Preemption enabled, min delay 30 sec
Active is local, weighting 75
R3#sh glbp
FastEthernet0/0 - Group 47
State is Standby
1 state change, last state change 00:09:23
Virtual IP address is 180.40.7.134
Hello time 3 sec, hold time 10 sec
Next hello sent in 0.516 secs
Redirect time 600 sec, forwarder time-out 14400 sec
Preemption disabled
Active is 180.40.7.131, priority 100 (expires in 7.071 sec)
Standby is local
Priority 100 (default)
Weighting 75, low (configured 100), thresholds: lower 90, upper 100
Track object 2 state Down decrement 25
Track object 4 state Up decrement 25
Load balancing: round-robin
There are 2 forwarders (1 active)
Forwarder 1
State is Listen
MAC address is 0007.b400.2f01 (learnt)
Owner ID is 0012.7f8d.1dc1
Time to live: 14397.067 sec (maximum 14400 sec)
Preemption enabled, min delay 30 sec
Active is 180.40.7.131 (primary), weighting 100 (expires in 7.067 sec)
--More-- Forwarder 2
State is Active
1 state change, last state change 00:09:31
MAC address is 0007.b400.2f02 (default)
Owner ID is 0012.7f8d.1ee0
Preemption enabled, min delay 30 sec
Active is local, weighting 75
R3#sh glbp
FastEthernet0/0 - Group 47
State is Standby
1 state change, last state change 00:09:31
Virtual IP address is 180.40.7.134
Hello time 3 sec, hold time 10 sec
Next hello sent in 1.266 secs
Redirect time 600 sec, forwarder time-out 14400 sec
Preemption disabled
Active is 180.40.7.131, priority 100 (expires in 7.821 sec)
Standby is local
Priority 100 (default)
Weighting 75, low (configured 100), thresholds: lower 90, upper 100
Track object 2 state Down decrement 25
Track object 4 state Up decrement 25
Load balancing: round-robin
There are 2 forwarders (1 active)
Forwarder 1
State is Listen
MAC address is 0007.b400.2f01 (learnt)
Owner ID is 0012.7f8d.1dc1
Time to live: 14397.817 sec (maximum 14400 sec)
Preemption enabled, min delay 30 sec
Active is 180.40.7.131 (primary), weighting 100 (expires in 7.817 sec)
--More-- Forwarder 2
State is Listen
2 state changes, last state change 00:00:00
MAC address is 0007.b400.2f02 (default)
Owner ID is 0012.7f8d.1ee0
Preemption enabled, min delay 30 sec
Active is 180.40.7.131 (secondary), weighting 75 (expires in 9.439 sec)
R3#
*Mar 2 21:58:01.356: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 47 Fwd 2 state Active -> Listen
R3#sh glbp
FastEthernet0/0 - Group 47
State is Standby
1 state change, last state change 00:09:36
Virtual IP address is 180.40.7.134
Hello time 3 sec, hold time 10 sec
Next hello sent in 2.643 secs
Redirect time 600 sec, forwarder time-out 14400 sec
Preemption disabled
Active is 180.40.7.131, priority 100 (expires in 9.199 sec)
Standby is local
Priority 100 (default)
Weighting 75, low (configured 100), thresholds: lower 90, upper 100
Track object 2 state Down decrement 25
Track object 4 state Up decrement 25
Load balancing: round-robin
There are 2 forwarders (0 active)
Forwarder 1
State is Listen
MAC address is 0007.b400.2f01 (learnt)
Owner ID is 0012.7f8d.1dc1
Time to live: 14399.195 sec (maximum 14400 sec)
Preemption enabled, min delay 30 sec
Active is 180.40.7.131 (primary), weighting 100 (expires in 9.195 sec)
--More-- Forwarder 2
State is Listen
2 state changes, last state change 00:00:03
MAC address is 0007.b400.2f02 (default)
Owner ID is 0012.7f8d.1ee0
Preemption enabled, min delay 30 sec
Active is 180.40.7.131 (secondary), weighting 100 (expires in 8.690 sec)
R3#
RACK98AS>7
[Resuming connection 7 to r7 ... ]
*Mar
R7#sh glbp brie
Interface Grp Fwd Pri State Address Active router Standby router
Fa0/1 47 - 100 Active 180.40.7.134 local 180.40.7.129
Fa0/1 47 1 7 Active 0007.b400.2f01 local -
Fa0/1 47 2 7 Active 0007.b400.2f02 local -
R7#
R7#
R7#
R7#
R7#sh hsrp brie
^
% Invalid input detected at '^' marker.
R7#sh hsrp brie sta
R7#sh stan
R7#sh standby
R7#sh standby
FastEthernet0/1 - Group 47
State is Active
17 state changes, last state change 00:01:19
Virtual IP address is 180.40.7.132
Active virtual MAC address is 0000.0c07.ac2f
Local virtual MAC address is 0000.0c07.ac2f (default)
Hello time 3 sec, hold time 10 sec
Next hello sent in 1.838 secs
Preemption enabled
Active router is local
Standby router is 180.40.7.129, priority 95 (expires in 9.828 sec)
Priority 100 (default 100)
IP redundancy name is "hsrp-Fa0/1-47" (default)
R7#qsh standby brie
P indicates configured to preempt.
|
Interface Grp Prio P State Active Standby Virtual IP
Fa0/1 47 100 P Active local 180.40.7.129 180.40.7.132
R7#
R7#
R7#sh vrrp brie
Interface Grp Pri Time Own Pre State Master addr Group addr
Fa0/1 47 100 3609 Y Backup 180.40.7.129 180.40.7.133
R7#
R7#
R7#
R7#
RACK98AS>3
[Resuming connection 3 to r3 ... ]
R3#
RACK98AS>2
[Resuming connection 2 to r2 ... ]
*M
R2(config-if)#no shut
R2(config-if)#^Z
R2#
*Mar 2 21:59:22.145
RACK98AS>3
[Resuming connection 3 to r3 ... ]
*Ma
R3#
*Mar 2 21:59:24.068: %LINK-3-UPDOWN: Interface Serial1/2, changed state to up
*Mar 2 21:59:25.070: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up
R3#sh run | b track
track 3 ip route 20.10.2.0 255.255.255.0 reachability
!
track 4 ip route 20.10.1.0 255.255.255.0 reachability
!
!
!
class-map match-all dscp26
match dscp af31
class-map match-all dscp14
match dscp af13
class-map match-all dscp24
match dscp cs3
class-map match-all telnet
match protocol telnet
class-map match-all dscp12
match dscp af12
class-map match-all dscp28
match dscp af32
class-map match-all prec3
match ip precedence 3
class-map match-all ftp
match protocol ftp
!
--More--
*Mar 2 21:59:34.417: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.162 on Serial1/2 from LOADING to FULL, Loading Done
--More-- !
policy-map test
class dscp12
class dscp14
class dscp26
class dscp28
class prec3
policy-map Prob7
class dscp12
priority percent 25
class telnet
bandwidth remaining percent 24
class ftp
bandwidth remaining percent 51
class class-default
bandwidth remaining percent 25
!
!
!
!
!
!
interface FastEthernet0/0
--More-- ip address dhcp
ip policy route-map Prob1
duplex auto
speed auto
vrrp 47 ip 180.40.7.133
vrrp 47 priority 150
glbp 47 ip 180.40.7.134
glbp 47 weighting 100 lower 90
glbp 47 weighting track 2 decrement 25
glbp 47 weighting track 4 decrement 25
standby 47 ip 180.40.7.132
standby 47 priority 120
standby 47 preempt
standby 47 track Serial1/0 25
standby 47 track Serial1/2 25
standby 47 track 3 decrement 25
service-policy input test
!
interface BRI0/0
no ip address
shutdown
!
interface FastEthernet0/1
--More--
R3#
*Mar 2 21:59:55.047: %GLBP-6-FWDSTATECHANGE: FastEthernet0/0 Grp 47 Fwd 2 state Listen -> Active
R3#
RACK98AS>7
[Resuming connection 7 to r7 ... ]
*Mar
R7#sh run | b track
track 1 ip route 20.10.1.0 255.255.255.0 reachability
!
!
!
class-map match-all S5Other
match access-group 1
class-map match-all S5Telnet
match access-group 1
match protocol telnet
class-map match-any jpg
match protocol http url "*jpg"
match protocol http url "*jpeg"
match protocol http url "*jpe"
match protocol http mime "*jpe"
match protocol http mime "*jpeg"
match protocol http mime "*jpg"
!
!
policy-map Prob5
class jpg
shape average 1000000
class S5Telnet
bandwidth 1000
--More-- class S5Other
police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1
!
!
!
!
!
!
interface FastEthernet0/0
ip address 208.28.1.1 255.255.255.0
speed auto
half-duplex
!
interface BRI0/0
no ip address
shutdown
!
interface FastEthernet0/1
ip address 180.40.7.131 255.255.255.224
ip helper-address 180.40.7.66
speed auto
half-duplex
--More-- vrrp 47 ip 180.40.7.133
--More-- glbp 47 ip 180.40.7.134
--More-- glbp 47 weighting 100 lower 90
--More-- glbp 47 weighting track 1 decrement 25
--More-- standby 47 ip 180.40.7.132
--More-- standby 47 preempt
--More-- service-policy output Prob5
--More-- !
--More-- interface Serial1/0
--More-- no ip address
--More-- encapsulation frame-relay
--More--
R7#
RACK98AS>6
[Resuming connection 6 to r6 ... ]
S6#sh mls qos map dscp-co sh mls qos map dscp-co
Dscp-cos map:
d1 : d2 0 1 2 3 4 5 6 7 8 9
---------------------------------------
0 : 00 00 00 00 00 00 00 00 01 01
1 : 01 01 01 01 01 01 02 02 02 02
2 : 02 02 02 02 03 03 03 03 03 03
3 : 03 03 04 04 04 04 04 04 04 04
4 : 05 05 05 05 05 05 05 05 06 06
5 : 06 06 06 06 06 06 07 07 07 07
6 : 07 07 07 07
S6#config t
Enter configuration commands, one per line. End with CNTL/Z.
S6(config)#mls qos dsc
S6(config)#mls qos dscp
S6(config)#mls qos dscp map dscp
S6(config)#mls qos map dscp-co
S6(config)#mls qos map dscp-cos ?
<0-63> DSCP values separated by spaces (up to 8 values total)
S6(config)#mls qos map dscp-cos 8 9 to 0
S6(config)#mls qos map dscp-cos 8 9 to 0nmls qos map dscp-cos 8 9 to 0omls qos map dscp-cos 8 9 to 0 mls qos map dscp-cos 8 9 to 0
S6(config)#int g 0/1
S6(config-if)#do sh mls qos int g0/1 qu
GigabitEthernet0/1
Egress expedite queue: dis
wrr bandwidth weights:
qid-weights
1 - 25
2 - 25
3 - 25
4 - 25
Dscp-threshold map:
d1 : d2 0 1 2 3 4 5 6 7 8 9
---------------------------------------
0 : 01 01 01 01 01 01 01 01 01 01
1 : 01 01 01 01 01 01 01 01 01 01
2 : 01 01 01 01 01 01 01 01 01 01
3 : 01 01 01 01 01 01 01 01 01 01
4 : 01 01 01 01 01 01 01 01 01 01
5 : 01 01 01 01 01 01 01 01 01 01
6 : 01 01 01 01
Cos-queue map:
cos-qid
0 - 1
1 - 1
2 - 2
3 - 2
4 - 3
5 - 3
6 - 4
7 - 4
S6(config-if)#wrr
S6(config-if)#wrr-queue ?
bandwidth Configure WRR bandwidth
cos-map Configure cos-map for a queue id
dscp-map Configure dscp-map for a queue threshold
queue-limit Configure queue-limit
random-detect Configure random-detect
threshold Configure queue tail-drop thresholds
S6(config-if)#wrr-queue co
S6(config-if)#wrr-queue cos-map ?
<1-4> enter cos-map queue id
S6(config-if)#wrr-queue cos-map 2 ?
<0-7> CoS values separated by spaces (up to 8 values total)
S6(config-if)#wrr-queue cos-map 2 0 2 4 5 6 7
S6(config-if)#wrr-queue cos-map 2 0 2 4 5 6 7 7 3 3
S6(config-if)#wrr-queue cos-map 3 32 0 2 4 5 6 7do sh mls qos int g0/1 qu
GigabitEthernet0/1
Egress expedite queue: dis
wrr bandwidth weights:
qid-weights
1 - 25
2 - 25
3 - 25
4 - 25
Dscp-threshold map:
d1 : d2 0 1 2 3 4 5 6 7 8 9
---------------------------------------
0 : 01 01 01 01 01 01 01 01 01 01
1 : 01 01 01 01 01 01 01 01 01 01
2 : 01 01 01 01 01 01 01 01 01 01
3 : 01 01 01 01 01 01 01 01 01 01
4 : 01 01 01 01 01 01 01 01 01 01
5 : 01 01 01 01 01 01 01 01 01 01
6 : 01 01 01 01
Cos-queue map:
cos-qid
0 - 2
1 - 1
2 - 2
3 - 3
4 - 2
5 - 2
6 - 2
7 - 2
S6(config-if)#q wrr
S6(config-if)#wrr-queue ?
bandwidth Configure WRR bandwidth
cos-map Configure cos-map for a queue id
dscp-map Configure dscp-map for a queue threshold
queue-limit Configure queue-limit
random-detect Configure random-detect
threshold Configure queue tail-drop thresholds
S6(config-if)#wrr-queue ba
S6(config-if)#wrr-queue bandwidth ?
<1-65536> enter bandwidth weight for qid 1
S6(config-if)#wrr-queue bandwidth 25 50 25 1
S6(config-if)#wrr
S6(config-if)#wrr-queue dsc
S6(config-if)#wrr-queue dscp-map ?
<1-2> enter dscp-map threshold id (1-2)
S6(config-if)#wrr-queue dscp-map 2 ?
<0-63> DSCP values separated by spaces (up to 8 values total)
S6(config-if)#wrr-queue dscp-map 2 10 26
S6(config-if)#wrr-queue dscp-map 2 10 26bandwidth 25 50 25 1do sh mls qos int g0/1 qu
GigabitEthernet0/1
Egress expedite queue: dis
wrr bandwidth weights:
qid-weights
1 - 25
2 - 50
3 - 25
4 - 1
Dscp-threshold map:
d1 : d2 0 1 2 3 4 5 6 7 8 9
---------------------------------------
0 : 01 01 01 01 01 01 01 01 01 01
1 : 02 01 01 01 01 01 01 01 01 01
2 : 01 01 01 01 01 01 02 01 01 01
3 : 01 01 01 01 01 01 01 01 01 01
4 : 01 01 01 01 01 01 01 01 01 01
5 : 01 01 01 01 01 01 01 01 01 01
6 : 01 01 01 01
Cos-queue map:
cos-qid
0 - 2
1 - 1
2 - 2
3 - 3
4 - 2
5 - 2
6 - 2
7 - 2
S6(config-if)#wrr
S6(config-if)#wrr-queue ?
bandwidth Configure WRR bandwidth
cos-map Configure cos-map for a queue id
dscp-map Configure dscp-map for a queue threshold
queue-limit Configure queue-limit
random-detect Configure random-detect
threshold Configure queue tail-drop thresholds
S6(config-if)#wrr-queue th
S6(config-if)#wrr-queue threshold ?
<1-4> enter threshold queue id (1-4)
S6(config-if)#wrr-queue threshold 1 40 100 ?
<cr>
S6(config-if)#wrr-queue threshold 1 40 100
S6(config-if)#wrr-queue threshold 1 40 100 3 60 1`00 00
S6(config-if)#^Z
S6#
1d22h: %SYS-5-CONFIG_I: Configured from console by console
S6#sh run int g1 0/1
^
% Invalid input detected at '^' marker.
S6#sh run int g1 0/11 0/1
Building configuration...
Current configuration : 270 bytes
!
interface GigabitEthernet0/1
switchport mode dynamic desirable
wrr-queue bandwidth 25 50 25 1
wrr-queue threshold 1 40 100
wrr-queue threshold 3 60 100
wrr-queue cos-map 1 1
wrr-queue cos-map 2 0 2 4 5 6 7
wrr-queue cos-map 3 3
wrr-queue dscp-map 2 10 26
end
S6#
S6#config t
Enter configuration commands, one per line. End with CNTL/Z.
S6(config)#int g 0/2
S6(config-if)# wrr-queue cos-map 1 1
S6(config-if)# wrr-queue cos-map 2 0 2 4 5 6 7
S6(config-if)# wrr-queue cos-map 3 3
S6(config-if)# wrr-queue bandwidth 25 50 25 1
S6(config-if)#?
Interface configuration commands:
arp Set arp type (arpa, probe, snap) or timeout
auto Configure Automation
bandwidth Set bandwidth informational parameter
bgp-policy Apply policy propogated by bgp community string
carrier-delay Specify delay for interface transitions
cdp CDP interface subcommands
channel-group Etherchannel/port bundling configuration
channel-protocol Select the channel protocol (LACP, PAgP)
dampening Enable event dampening
default Set a command to its defaults
delay Specify interface throughput delay
description Interface specific description
dot1x Interface Config Commands for 802.1x
eou EAPoUDP Interface Configuration Commands
exit Exit from interface configuration mode
fair-queue Enable Fair Queuing on an Interface
flowcontrol Configure flow operation.
help Description of the interactive help system
hold-queue Set hold queue depth
ip Interface Internet Protocol config commands
keepalive Enable keepalive
--More--
S6(config-if)#wrr
S6(config-if)#wrr-queue ?
bandwidth Configure WRR bandwidth
cos-map Configure cos-map for a queue id
dscp-map Configure dscp-map for a queue threshold
queue-limit Configure queue-limit
random-detect Configure random-detect
threshold Configure queue tail-drop thresholds
S6(config-if)#wrr-queue ran
S6(config-if)#wrr-queue random-detect ?
max-threshold max-thresholds
S6(config-if)#wrr-queue random-detect max ?
<1-4> enter threshold queue id (1-4)
S6(config-if)#wrr-queue random-detect max 3 ?
<1-100> enter percent of queue size for threshold 1
S6(config-if)#wrr-queue random-detect max 3 wrr
S6(config-if)#wrr-queue dsc
S6(config-if)#wrr-queue dscp-map ?
<1-2> enter dscp-map threshold id (1-2)
S6(config-if)#wrr-queue dscp-map 3 2 ?
<0-63> DSCP values separated by spaces (up to 8 values total)
S6(config-if)#wrr-queue dscp-map 2 28 30
S6(config-if)#wrr
S6(config-if)#wrr-queue ran
S6(config-if)#wrr-queue random-detect ?
max-threshold max-thresholds
S6(config-if)#wrr-queue random-detect m
S6(config-if)#wrr-queue random-detect max-threshold ?
<1-4> enter threshold queue id (1-4)
S6(config-if)#wrr-queue random-detect max-threshold 3 ?
<1-100> enter percent of queue size for threshold 1
S6(config-if)#wrr-queue random-detect max-threshold 3 80 ?
<1-100> enter percent of queue size for threshold 2
S6(config-if)#wrr-queue random-detect max-threshold 3 80 40 ?
<cr>
S6(config-if)#wrr-queue random-detect max-threshold 3 80 40
S6(config-if)#^Z
S6#sh uru
1d22h: %SYS-5-CONFIG_I: Configured from console by console
S6#sh uru run int g 0/2
Building configuration...
Current configuration : 257 bytes
!
interface GigabitEthernet0/2
switchport mode dynamic desirable
wrr-queue bandwidth 25 50 25 1
wrr-queue random-detect max-threshold 3 80 40
wrr-queue cos-map 1 1
wrr-queue cos-map 2 0 2 4 5 6 7
wrr-queue cos-map 3 3
wrr-queue dscp-map 2 28 30
end
S6#
S6#
RACK98AS>7
[Resuming connection 7 to r7 ... ]
R7#sh run int fa 0/0
Building configuration...
Current configuration : 95 bytes
!
interface FastEthernet0/0
ip address 208.28.1.1 255.255.255.0
speed auto
half-duplex
end
R7#configt sh class
R7#sh class-map
Class Map match-all S5Other (id 2)
Match access-group 1
Class Map match-any class-default (id 0)
Match any
Class Map match-all S5Telnet (id 1)
Match access-group 1
Match protocol telnet
Class Map match-any jpg (id 3)
Match protocol http url "*jpg"
Match protocol http url "*jpeg"
Match protocol http url "*jpe"
Match protocol http mime "*jpe"
Match protocol http mime "*jpeg"
Match protocol http mime "*jpg"
R7#config t
Enter configuration commands, one per line. End with CNTL/Z.
R7(config)#class
R7(config)#class-map ftp
R7(config-cmap)#match pro
R7(config-cmap)#match protocol ftp
R7(config-cmap)#exit
R7(config)#class
R7(config)#class-map telnet
R7(config-cmap)#match pro
R7(config-cmap)#match protocol telnet
R7(config-cmap)#exit
R7(config)#nbp
R7(config)#nb ip nb
R7(config)#ip nbar po
R7(config)#ip nbar port-map ?
bgp Border Gateway Protocol
citrix Citrix Traffic
cuseeme CU-SeeMe desktop video conference
custom-01 Custom protocol custom-01
custom-02 Custom protocol custom-02
custom-03 Custom protocol custom-03
custom-04 Custom protocol custom-04
custom-05 Custom protocol custom-05
custom-06 Custom protocol custom-06
custom-07 Custom protocol custom-07
custom-08 Custom protocol custom-08
custom-09 Custom protocol custom-09
custom-10 Custom protocol custom-10
dhcp Dynamic Host Configuration
dns Domain Name Server lookup
egp Exterior Gateway Protocol
eigrp Enhanced Interior Gateway Routing Protocol
exchange MS-RPC for Exchange
fasttrack FastTrack Traffic - KaZaA, Morpheus, Grokster...
finger Finger
ftp File Transfer Protocol
gnutella Gnutella Traffic - BearShare,LimeWire,Gnotella...
--More--
R7(config)#ip nbar port-map ftp 20 21t20 21c20 21p20 21 20 21
R7(config)#pol
R7(config)#policy-map Prob20to22
R7(config-pmap)#clas
R7(config-pmap)#class ftp
R7(config-pmap-c)#ban
R7(config-pmap-c)#bandwidth re
R7(config-pmap-c)#bandwidth remaining p
R7(config-pmap-c)#bandwidth remaining percent 25
R7(config-pmap-c)#bandwidth remaining percent 25class ftp telnet
R7(config-pmap-c)#class telnetbandwidth remaining percent 25
R7(config-pmap-c)#int fa 0/0
R7(config-if)#bban
R7(config-if)#bban re
R7(config-if)#re band max
R7(config-if)#max-reserved-bandwidth 100
R7(config-if)#max-reserved-bandwidth 100nmax-reserved-bandwidth 100omax-reserved-bandwidth 100 max-reserved-bandwidth 100
R7(config-if)#exit
R7(config)#pol
R7(config)#policy-map test
R7(config-pmap)#class
R7(config-pmap)#class ftp
R7(config-pmap-c)#band 25 per 25
R7(config-pmap-c)#class telnet
R7(config-pmap-c)#class telnet band per 25
R7(config-pmap-c)#clas c ss class-deffaulaul ault
R7(config-pmap-c)#ban
R7(config-pmap-c)#bandwidth per 50
R7(config-pmap-c)#int fa 0/0
R7(config-if)#ser out test
I/f FastEthernet0/0 class class-default requested bandwidth 50%, available only 25%
R7(config-if)#max
R7(config-if)#max-reserved-bandwidth 100
R7(config-if)#max-reserved-bandwidth 100ser out test
R7(config-if)#exu ser out testnser out testoser out test ser out test
R7(config-if)#ser out Prob20to22
R7(config-if)#exit
R7(config)#no pol
R7(config)#no policy-map test
R7(config)#^Z
R7#sh
*Mar 1 23:49:35.525: %SYS-5-CONFIG_I: Configured from console by console
R7#sh run | b class
class-map match-all telnet
match protocol telnet
class-map match-all S5Other
match access-group 1
class-map match-all S5Telnet
match access-group 1
match protocol telnet
class-map match-all ftp
match protocol ftp
class-map match-any jpg
match protocol http url "*jpg"
match protocol http url "*jpeg"
match protocol http url "*jpe"
match protocol http mime "*jpe"
match protocol http mime "*jpeg"
match protocol http mime "*jpg"
!
!
policy-map Prob5
class jpg
shape average 1000000
class S5Telnet
bandwidth 1000
--More-- class S5Other
police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1
policy-map Prob20to22
class ftp
bandwidth remaining percent 25
class telnet
bandwidth remaining percent 25
!
!
!
!
!
!
interface FastEthernet0/0
ip address 208.28.1.1 255.255.255.0
speed auto
half-duplex
max-reserved-bandwidth 100
service-policy output Prob20to22
!
interface BRI0/0
no ip address
--More--
R7#config t
Enter configuration commands, one per line. End with CNTL/Z.
R7(config)#po
R7#
*Mar 1 23:50:00.590: %SYS-5-CONFIG_I: Configured from console by console
R7#config t
Enter configuration commands, one per line. End with CNTL/Z.
R7(config)#class
R7(config)#class-map sql
R7(config-cmap)#match pro
R7(config-cmap)#match protocol s?
secure-ftp secure-http secure-imap secure-irc
secure-ldap secure-nntp secure-pop3 secure-telnet
smtp snapshot snmp socks
sqlnet sqlserver ssh streamwork
stun sunrpc syslog
R7(config-cmap)#match protocol sqls
R7(config-cmap)#match protocol sqlserver ?
<cr>
R7(config-cmap)#match protocol sqlserver
R7(config-cmap)#match protocol sqlserver class-map sql no policy-map testexit ser out Prob20to22t Prob20to22 Prob20to22 Prob20to22 Prob20to22 Prob20to22 Prob20to22 Prob20to22 p Prob20to22o Prob20to22l Prob20to22
R7(config-pmap)#class
R7(config-pmap)#class sql
R7(config-pmap-c)#exit
R7(config-pmap)#exit
R7(config)#do s sh access-list
Standard IP access list 1
10 permit 208.28.1.2 (288788 matches)
R7(config)#access-list 2 per 87.23. 100 per ip 87.23.11.123 h87.23.11.123 o87.23.11.123 s87.23.11.123 t87.23.11.123 87.23.11.123 87.23.11.123 any
R7(config)#access-list 100 per ip host 87.23.11.123 any ahost 87.23.11.123 nhost 87.23.11.123 yhost 87.23.11.123 host 87.23.11.123
R7(config)#class
R7(config)#class-map q sql
R7(config-cmap)#match acc
R7(config-cmap)#match access-group 100
R7(config-cmap)#match access-group 100class-map sql access-list 100 per ip any host 87.23.11.123 host 87.23.11.123 any do sh access-list exit class sqlpol Prob20to22
R7(config-pmap)#pol Prob20to22match access-group 100class-map sql
R7(config-cmap)#pri
R7(config-cmap)#prio
R7(config-cmap)#prio > ?
QoS class-map configuration commands:
description Class-Map description
exit Exit from QoS class-map configuration mode
match classification criteria
no Negate or set default values of a command
rename Rename this class-map
R7(config-cmap)#class-map sqlpol Prob20to22match access-group 100class-map sql match access-group 100pol Prob20to22
R7(config-pmap)#CLASS
R7(config-pmap)#CLASS sql
R7(config-pmap-c)#pri
R7(config-pmap-c)#priority ?
<8-2000000> Kilo Bits per second
percent % of total bandwidth
R7(config-pmap-c)#priority 56 ?
<32-2000000> Burst in bytes
<cr>
R7(config-pmap-c)#priority 56 128
R7(config-pmap-c)#^Z
R7#sh ru
*Mar 1 23:57:31.076: %SYS-5-CONFIG_I: Configured from console by console
R7#sh ru n| b n | class
^
% Invalid input detected at '^' marker.
R7#sh run | classbclass class
class-map match-all telnet
match protocol telnet
class-map match-all S5Other
match access-group 1
class-map match-all S5Telnet
match access-group 1
match protocol telnet
class-map match-all ftp
match protocol ftp
class-map match-all sql
match protocol sqlserver
match access-group 100
class-map match-any jpg
match protocol http url "*jpg"
match protocol http url "*jpeg"
match protocol http url "*jpe"
match protocol http mime "*jpe"
match protocol http mime "*jpeg"
match protocol http mime "*jpg"
!
!
policy-map Prob5
class jpg
--More-- shape average 1000000
class S5Telnet
bandwidth 1000
class S5Other
police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1
policy-map Prob20to22
class ftp
bandwidth remaining percent 25
class telnet
bandwidth remaining percent 25
class sql
priority 56 128
!
!
!
!
!
!
interface FastEthernet0/0
ip address 208.28.1.1 255.255.255.0
speed auto
half-duplex
--More--
R7#sh run| b n | b | b access-list
access-list 1 permit 208.28.1.2
access-list 100 permit ip host 87.23.11.123 any
access-list 100 permit ip any host 87.23.11.123
priority-list 1 protocol ip high tcp telnet
priority-list 1 protocol ip low tcp www
priority-list 1 default medium
!
!
!
!
!
!
!
!
!
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
privilege level 15
no login
!
--More--
R7#config t
Enter configuration commands, one per line. End with CNTL/Z.
R7(config)#priority 56 128CLASS sql pol Prob20to22
R7(config-pmap)#class class-deafult
% class map class-deafult not configured
R7(config-pmap)#class class-deafultult ult fultuault
R7(config-pmap-c)#fa
R7(config-pmap-c)#fair-queue
R7(config-pmap-c)#do sh pol int fa 0/0
FastEthernet0/0
Service-policy output: Prob20to22
Class-map: ftp (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: protocol ftp
Queueing
Output Queue: Conversation 265
Bandwidth remaining 25 (%) Max Threshold 64 (packets)
(pkts matched/bytes matched) 0/0
(depth/total drops/no-buffer drops) 0/0/0
Class-map: telnet (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: protocol telnet
Queueing
Output Queue: Conversation 266
Bandwidth remaining 25 (%) Max Threshold 64 (packets)
(pkts matched/bytes matched) 0/0
(depth/total drops/no-buffer drops) 0/0/0
--More--
Class-map: sql (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: protocol sqlserver
Match: access-group 100
Queueing
Strict Priority
Output Queue: Conversation 264
Bandwidth 56 (kbps) Burst 128 (Bytes)
(pkts matched/bytes matched) 0/0
(total drops/bytes drops) 0/0
Class-map: class-default (match-any)
151 packets, 15204 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
Queueing
Flow Based Fair Queueing
Maximum Number of Hashed Queues 256
(total queued/total drops/no-buffer drops) 0/0/0
R7(config-pmap-c)# do sh pol int fa 0/0fair-queue ?
<16-4096> Number Dynamic Conversation Queues
<cr>
R7(config-pmap-c)#fair-queue 512
R7(config-pmap-c)#^Z
R7#sh run
*Mar 1 23:59:47.135: %SYS-5-CONFIG_I: Configured from console by console
R7#sh run | b pol
policy-map Prob5
class jpg
shape average 1000000
class S5Telnet
bandwidth 1000
class S5Other
police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1
policy-map Prob20to22
class ftp
bandwidth remaining percent 25
class telnet
bandwidth remaining percent 25
class sql
priority 56 128
class class-default
fair-queue 512
!
!
!
!
!
!
--More--
R7#q config t
Enter configuration commands, one per line. End with CNTL/Z.
R7(config)#pol
R7(config)#policy-map Prob23and24
R7(config-pmap)#class ftp
R7(config-pmap-c)#po, l
R7(config-pmap-c)#police 256 ?
<8000-2000000000> Bits per second
cir Committed information rate
R7(config-pmap-c)#police 256000
R7(config-pmap-c-police)#exit
R7(config-pmap-c)#class telnet
R7(config-pmap-c)#pol
R7(config-pmap-c)#police 56000 ?
<1000-512000000> Burst bytes
bc Conform burst
conform-action action when rate is less than conform burst
pir Peak Information Rate
<cr>
R7(config-pmap-c)#police 56000 1400 ?
<1000-512000000> Burst bytes
be Excess burst
conform-action action when rate is less than conform burst
pir Peak Information Rate
<cr>
R7(config-pmap-c)#police 56000 1400 3500 ?
conform-action action when rate is less than conform burst
<cr>
R7(config-pmap-c)#police 56000 1400 3500 con
R7(config-pmap-c)#police 56000 1400 3500 conform-action se
R7(config-pmap-c)#police 56000 1400 3500 conform-action set-p
R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit ?
<0-7> new precedence
R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 ?
exceed-action action when rate is within conform and conform + exceed burst
<cr>
R7(config-pmap-c)#police 56000 1400 3500 conform-action set-prec-transmit 1 e$0 1400 3500 conform-action set-prec-transmit 1 ex
R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action se
R7(config-pmap-c)#$0 conform-action set-prec-transmit 1 exceed-action set-p
R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0 > ?
violate-action action when rate is greater than conform + exceed burst
<cr>
R7(config-pmap-c)#$-prec-transmit 1 exceed-action set-prec-transmit 0
R7(config-pmap-c-police)#exit
R7(config-pmap-c)#exit
R7(config-pmap)#class class-default
R7(config-pmap-c)#fa
R7(config-pmap-c)#fair-queue
R7(config-pmap-c)#?
QoS policy-map class configuration commands:
bandwidth Bandwidth
compression Activate Compression
drop Drop all packets
exit Exit from QoS class action configuration mode
fair-queue Enable Flow-based Fair Queuing in this Class
no Negate or set default values of a command
police Police
priority Strict Scheduling Priority for this Class
queue-limit Queue Max Threshold for Tail Drop
random-detect Enable Random Early Detection as drop policy
service-policy Configure QoS Service Policy
set Set QoS values
shape Traffic Shaping
R7(config-pmap-c)#qu
R7(config-pmap-c)#queue-limit ?
<1-4096> Packets
R7(config-pmap-c)#queue-limit 100
R7(config-pmap-c)#int s 1/0.1
R7(config-subif)#ser out Prob23and24
CBWFQ : Not supported on subinterfaces
R7(config-subif)#
R7(config-subif)#
R7(config-subif)#
R7(config-subif)#exit
R7(config)#map
R7(config)#map-cl
R7(config)#map-class fra
R7(config)#map-class frame-relay Prob23and24
R7(config-map-class)#ser
R7(config-map-class)#service-policy out Prob12 23and24
R7(config-map-class)#int s 1/0.1
R7(config-subif)#fra
R7(config-subif)#fram
R7(config-subif)#frame-relay clas
R7(config-subif)#frame-relay class Prob23and24
R7(config-subif)#int s 1/0
R7(config-if)#fram
R7(config-if)#frame-relay traff
R7(config-if)#frame-relay traffic-shaping
R7(config-if)#^Z
R7#sh
*Mar 2 00:05:20.297: %SYS-5-CONFIG_I: Configured from console by console
R7#sh pol int s 1/0.1
Serial1/0.1: DLCI 703 -
Service-policy output: Prob23and24
Class-map: ftp (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: protocol ftp
police:
cir 256000 bps, bc 8000 bytes
conformed 0 packets, 0 bytes; actions:
transmit
exceeded 0 packets, 0 bytes; actions:
drop
conformed 0 bps, exceed 0 bps
Class-map: telnet (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: protocol telnet
police:
cir 56000 bps, bc 1400 bytes
conformed 0 packets, 0 bytes; actions:
--More-- set-prec-transmit 1
exceeded 0 packets, 0 bytes; actions:
set-prec-transmit 0
conformed 0 bps, exceed 0 bps
Class-map: class-default (match-any)
2 packets, 168 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
Queueing
Flow Based Fair Queueing
Maximum Number of Hashed Queues 16
(total queued/total drops/no-buffer drops) 0/0/0
R7#sh run | b pol
policy-map Prob5
class jpg
shape average 1000000
class S5Telnet
bandwidth 1000
class S5Other
police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1
policy-map Prob20to22
class ftp
bandwidth remaining percent 25
class telnet
bandwidth remaining percent 25
class sql
priority 56 128
class class-default
fair-queue 512
policy-map Prob23and24
class ftp
police 256000
class telnet
police 56000 1400 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0
--More-- class class-default
fair-queue
queue-limit 100
!
!
!
!
!
!
interface FastEthernet0/0
ip address 208.28.1.1 255.255.255.0
speed auto
half-duplex
max-reserved-bandwidth 100
service-policy output Prob20to22
!
interface BRI0/0
no ip address
shutdown
!
interface FastEthernet0/1
ip address 180.40.7.131 255.255.255.224
ip helper-address 180.40.7.66
--More--
R7#sh run int s 1/0 |int s 1/0 int s 1/0bint s 1/0 int s 1/0int s 1/0 1/0 1/0 1/0 1/0 1/0
interface Serial1/0
no ip address
encapsulation frame-relay
no fair-queue
frame-relay traffic-shaping
!
interface Serial1/0.1 point-to-point
ip address 180.40.7.65 255.255.255.224
ip ospf network broadcast
ip ospf priority 0
frame-relay class Prob23and24
frame-relay interface-dlci 703
!
interface Serial1/0.2 point-to-point
ip address 180.40.7.161 255.255.255.224
ip helper-address 208.28.1.99
ip ospf network point-to-multipoint
frame-relay priority-dlci-group 1 702 702 702 702
frame-relay interface-dlci 702 protocol ip 180.40.7.162
!
interface Serial1/1
no ip address
shutdown
--More-- !
interface Serial1/2
no ip address
shutdown
!
interface Serial1/3
no ip address
shutdown
!
interface Serial1/4
no ip address
shutdown
!
interface Serial1/5
no ip address
shutdown
!
interface Serial1/6
no ip address
shutdown
!
interface Serial1/7
no ip address
--More-- shutdown
!
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
!
ip classless
!
no ip http server
no ip http secure-server
!
!
map-class frame-relay Prob23and24
service-policy output Prob23and24
access-list 1 permit 208.28.1.2
access-list 100 permit ip host 87.23.11.123 any
access-list 100 permit ip any host 87.23.11.123
priority-list 1 protocol ip high tcp telnet
priority-list 1 protocol ip low tcp www
priority-list 1 default medium
!
!
!
--More--
R7#config t
Enter configuration commands, one per line. End with CNTL/Z.
R7(config)#
R7(config)#i pol frame-relay traffic-shaping int s 1/0 frame-relay class Prob23and24int s 1/0.1 frame-relay class Prob23and24Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 Prob23and24 pProb23and24oProb23and24lProb23and24 Prob23and24
R7(config-pmap)#class class-deaultfault
R7(config-pmap-c)#pol
R7(config-pmap-c)#police 512000
R7(config-pmap-c-police)#exit
R7(config-pmap-c)#exit
R7(config-pmap)#exitpolice 512000class class-defaultpol Prob23and24 frame-relay traffic-shaping int s 1/0 frame-relay class Prob23and24
^
% Invalid input detected at '^' marker.
R7(config-pmap)#exit
R7(config)#map
R7(config)#map-cl
R7(config)#map-class class fram
R7(config)#map-class fram Prob23and24
R7(config-map-class)#fam
R7(config-map-class)#fam ram
R7(config-map-class)#frame-relay cir 600 ?
<1-45000000> Applied to both Incoming/Outgoing CIR, Bits per second
in Incoming CIR
out Outgoing CIR
R7(config-map-class)#frame-relay cir 600000
R7(config-map-class)#^Z
R7#
*Mar 2 00:10:41.456: %SYS-5-CONFIG_I: Configured from console by console
R7#sh run | b pol
policy-map Prob5
class jpg
shape average 1000000
class S5Telnet
bandwidth 1000
class S5Other
police 5000000 conform-action set-prec-transmit 3 exceed-action set-prec-transmit 1
policy-map Prob20to22
class ftp
bandwidth remaining percent 25
class telnet
bandwidth remaining percent 25
class sql
priority 56 128
class class-default
fair-queue 512
policy-map Prob23and24
class ftp
police 256000
class telnet
police 56000 1400 3500 conform-action set-prec-transmit 1 exceed-action set-prec-transmit 0
--More-- class class-default
--More-- fair-queue
--More-- queue-limit 100
--More-- police 512000
--More-- !
--More-- !
--More-- !
!
!
!
interface FastEthernet0/0
ip address 208.28.1.1 255.255.255.0
speed auto
half-duplex
max-reserved-bandwidth 100
service-policy output Prob20to22
!
interface BRI0/0
no ip address
shutdown
!
interface FastEthernet0/1
ip address 180.40.7.131 255.255.255.224
ip helper-address 180.40.7.66
speed auto
half-duplex
vrrp 47 ip 180.40.7.133
glbp 47 ip 180.40.7.134
glbp 47 weighting 100 lower 90
--More-- glbp 47 weighting track 1 decrement 25
standby 47 ip 180.40.7.132
standby 47 preempt
service-policy output Prob5
!
interface Serial1/0
no ip address
encapsulation frame-relay
no fair-queue
frame-relay traffic-shaping
!
interface Serial1/0.1 point-to-point
ip address 180.40.7.65 255.255.255.224
ip ospf network broadcast
ip ospf priority 0
frame-relay class Prob23and24
frame-relay interface-dlci 703
!
interface Serial1/0.2 point-to-point
ip address 180.40.7.161 255.255.255.224
ip helper-address 208.28.1.99
ip ospf network point-to-multipoint
frame-relay priority-dlci-group 1 702 702 702 702
--More-- frame-relay interface-dlci 702 protocol ip 180.40.7.162
!
interface Serial1/1
no ip address
shutdown
!
interface Serial1/2
no ip address
shutdown
!
interface Serial1/3
no ip address
shutdown
!
interface Serial1/4
no ip address
shutdown
!
interface Serial1/5
no ip address
shutdown
!
interface Serial1/6
--More-- no ip address
shutdown
!
interface Serial1/7
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
!
ip classless
!
no ip http server
no ip http secure-server
!
!
map-class frame-relay Prob23and24
frame-relay cir 600000
service-policy output Prob23and24
access-list 1 permit 208.28.1.2
access-list 100 permit ip host 87.23.11.123 any
access-list 100 permit ip any host 87.23.11.123
--More--
R7#
RACK98AS>2
[Resuming connection 2 to r2 ... ]
: %SYS-5-CONFIG_I: Configured from console by console
R2#
R2#config t
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#mlp
R2(config)#mlp ap
R2(config)#map-cl
R2(config)#map-class fram Prob25and26
R2(config-map-class)#far ram cir 64000
R2(config-map-class)#fram
R2(config-map-class)#frame-relay ad
R2(config-map-class)#frame-relay adaptive-shaping be
R2(config-map-class)#frame-relay adaptive-shaping becn
R2(config-map-class)#int s 1/0.1
R2(config-subif)#fram class Prob25and26
R2(config-subif)#^Z
R2#
*Mar 2 23:41:42.643: %SYS-5-CONFIG_I: Configured from console by console
R2#
R2#
R2#
R2#
R2#sh run int s 1/0.1
Building configuration...
Current configuration : 177 bytes
!
interface Serial1/0.1 point-to-point
ip address 180.40.7.67 255.255.255.224
ip ospf network broadcast
frame-relay class Prob25and26
frame-relay interface-dlci 203
end
R2#
R2#sh run | b map-class
map-class frame-relay Prob3
frame-relay cir 64000
frame-relay bc 64000
frame-relay be 32000
frame-relay adaptive-shaping becn
!
map-class frame-relay Prob25and26
frame-relay cir 64000
frame-relay adaptive-shaping becn
access-list 100 deny ospf any any
access-list 100 permit ip any any
!
!
!
!
!
!
!
!
!
line con 0
exec-timeout 0 0
logging synchronous
--More--
R2#sh traff ins 1/0.1
^
% Invalid input detected at '^' marker.
R2#sh traff ins 1/0.1 1/0.1
^
% Invalid input detected at '^' marker.
R2#sh traff in 1/0.11
Interface Se1/0
Access Target Byte Sustain Excess Interval Increment Adapt
VC List Rate Limit bits/int bits/int (ms) (bytes) Active
201 56000 875 7000 0 125 875 -
Interface Se1/0.1
Access Target Byte Sustain Excess Interval Increment Adapt
VC List Rate Limit bits/int bits/int (ms) (bytes) Active
203 64000 1000 64000 0 125 1000 BECN
Interface Se1/0.2
Access Target Byte Sustain Excess Interval Increment Adapt
VC List Rate Limit bits/int bits/int (ms) (bytes) Active
207 64000 5000 64000 32000 125 1000 BECN
R2#
R2#
R2#
R2#
R2#
R2#
R2#sh traff ser 1/0.1
Interface Se1/0.1
Access Target Byte Sustain Excess Interval Increment Adapt
VC List Rate Limit bits/int bits/int (ms) (bytes) Active
203 64000 1000 64000 0 125 1000 BECN
R2#sh traff ser 1/0.1 ?
| Output modifiers
<cr>
R2#sh traff ser 1/0.1 config t
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#in map c ffram class Prob25and26int s 1/0.1 frame-relay adaptive-shaping becn cir 64000 map-class fram Prob25and26
R2(config-map-class)#fram mi
R2(config-map-class)#fram mincir 32000
R2(config-map-class)#^Z
R2#s
*Mar 2 23:43:39.194: %SYS-5-CONFIG_I: Configured from console by console
R2#sconfig tsh traff ser 1/0.1 in 1/0.1s 1/0.1run | b map-class
map-class frame-relay Prob3
frame-relay cir 64000
frame-relay bc 64000
frame-relay be 32000
frame-relay adaptive-shaping becn
!
map-class frame-relay Prob25and26
frame-relay cir 64000
frame-relay mincir 32000
frame-relay adaptive-shaping becn
access-list 100 deny ospf any any
access-list 100 permit ip any any
!
!
!
!
!
!
!
!
!
line con 0
exec-timeout 0 0
--More--
R2#