=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2007.01.29 14:53:28 =~=~=~=~=~=~=~=~=~=~=~= confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip mu R1(config)#ip multicast- R1(config)#ip multicast-routing R1(config)#int s e 0/0 R1(config-if)#ip pim R1(config-if)#ip pim s R1(config-if)#ip pim sp R1(config-if)#ip pim sparse-d R1(config-if)#ip pim sparse-dense-mode R1(config-if)#ip pim sparse-dense-mode nt e 0/0  1 R1(config-if)#int e 0/1p pim sparse-dense-mode R1(config-if)# *Mar 1 04:51:38.059: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.57.100.1 on interface Ethernet0/0 (vrf default) R1(config-if)#int s 1/0;.      *Mar 1 04:51:40.543: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.100.1.1 on interface Ethernet0/1 (vrf default) R1(config-if)#int s 0/0.1 R1(config-subif)#int s 0/0.1p pim sparse-dense-mode R1(config-subif)#ip pim sparse-dense-mode nt s 0/0.1  2 R1(config-subif)#int s 0/0.2p pim sparse-dense-mode R1(config-subif)#int p pim sparse-dense-mode nt s 0/0.2 p pim sparse-dense-mode nt s 0/0.1  R1(config-subif)#shu   no shut R1(config-subif)#^Z R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip mu R2(config)#ip multicast- R2(config)#ip multicast-routing R2(config)#iu  int fa 0/1 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#int s 1/2 R2(config-if)#int s 1/2p pim sparse-dense-mode *Mar 1 04:51:23.086: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.98 on interface FastEthernet0/1 (vrf default) R2(config-if)#ip pim sparse-dense-mode R2(config-if)#ip pim sparse-dense-mode nt s 1/2  0.1 R2(config-subif)#int s 1/0.1p pim sparse-dense-mode R2(config-subif)#ip pim sparse-dense-mode nt s 1/0.1  2 R2(config-subif)#int s 1/0.2p pim sparse-dense-mode R2(config-subif)#^Z R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s 1/2 R3(config-if)#exit R3(config)#ip mu R3(config)#ip multicast- R3(config)#ip multicast-routing R3(config)#int s 1/2 R3(config-if)#ip pim sp R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)#ip pim sparse-dense-mode nt s 1/2  *Mar 1 04:51:42.859: %PIM-5-NBRCHG: neighbor 180.40.7.2 UP on interface Serial1/2 (vrf default) R3(config-if)#int s 1/2 0 R3(config-if)#int s 1/0p pim sparse-dense-mode R3(config-if)# *Mar 1 04:51:46.048: %PIM-5-NBRCHG: neighbor 180.40.7.35 UP on interface Serial1/0 (vrf default) *Mar 1 04:51:46.048: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.35 on interface Serial1/0 (vrf default) R3(config-if)#int fa 0/1 R3(config-if)#int fa 0/1p pim sparse-dense-mode R3(config-if)#^Z R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip mu R4(config)#ip multicast0 R4(config)#ip multicast0 - R4(config)#ip multicast-routing int      R4(config)#int fa 0/0 R4(config-if)#ip pim sp  de R4(config-if)#ip pim dense-mode R4(config-if)#ip igm R4(config-if)#ip igmp *Mar 1 04:54:31.678: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.130 on interface FastEthernet0/0 (vrf default) R4(config-if)#ip igmp join R4(config-if)#ip igmp join-group 224.4.4.4 R4(config-if)#^Z R4# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#confi t~  Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip mu S5(config)#ip multicast- S5(config)#ip multicast-routing S5(config)#int fa 0/1 S5(config-if)#ip op  pim sp S5(config-if)#ip pim sparse-d S5(config-if)#ip pim sparse-dense-mode S5(config-if)#^Z S5# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#copn  nfi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip mu S6(config)#ip multicast- S6(config)#ip multicast-routing S6(config)#int fa 0/2 S6(config-if)#ip pim sp S6(config-if)#ip pim sparse-d S6(config-if)#ip pim sparse-dense-mode S6(config-if)#^Z S6# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip mu R7(config)#ip multicast- R7(config)#ip multicast-routing R7(config)#in  t fa 0/1 R7(config-if)#ip pim sp R7(config-if)#ip pim sparse-d R7(config-if)#ip pim sparse-dense-mode R7(config-if)#^Z R7# *Mar 1 04:52:57.253: %PIM-5-NBRCHG: neighbor 17.100.1.1 UP on interface FastEthernet0/1 (vrf default) *Mar 1 04:52:57.689: %SYS-5-CONFIG_I: Configured from console by console R7# *Mar 1 04:52:59.224: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.100.1.2 on interface FastEthernet0/1 (vrf default) R7#ping 224.;4.4    4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 144 ms Reply to request 0 from 180.40.7.130, 192 ms Reply to request 0 from 180.40.7.130, 176 ms R7# RACK11AS>5 [Resuming connection 5 to r5 ... ] 04: S5#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 128 ms Reply to request 0 from 180.40.7.130, 176 ms Reply to request 0 from 180.40.7.130, 160 ms S5# RACK11AS>6 [Resuming connection 6 to r6 ... ] 04: S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 60 ms Reply to request 0 from 180.40.7.130, 112 ms Reply to request 0 from 180.40.7.130, 88 ms S6#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:45/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/2, Forward/Sparse-Dense, 00:00:43/00:00:00 (17.57.100.2, 224.4.4.4), 00:00:14/00:02:45, flags: PT Incoming interface: FastEthernet0/2, RPF nbr 180.40.7.98 Outgoing interface list: Null (17.100.1.2, 224.4.4.4), 00:00:45/00:02:14, flags: PTX Incoming interface: FastEthernet0/2, RPF nbr 180.40.7.98 Outgoing interface list: Null (*, 224.0.1.40), 00:01:13/00:02:59, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/2, Forward/Sparse-Dense, 00:01:13/00:00:00 S6#   RACK11AS>1 [Resuming connection 1 to r1 ... ] * R1#ah    sh run | b ip mu;l  l ip multicast-routing ip cef ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode half-duplex ! interface Serial0/0 --More--   no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim sparse-dense-mode half-duplex no keepalive ! interface Serial0/1 no ip address --More-- RACK11AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#sh run | b ip mul ip multicast-routing ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim dense-mode --More--   ip igmp join-group 224.4.4.4 --More--   duplex auto --More--   speed auto --More--  ! --More--  interface ATM1/0 --More--   R4# R4# R4# R4# R4#coni   fi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#fa  int fa 90  0/09  R4(config-if)#ip pim st R4(config-if)#ip pim state-refresh ? origination-interval PIM State-Refresh origination interval R4(config-if)#ip pim state-refresh o R4(config-if)#ip pim state-refresh origination-interval ? <1-100> Interval in seconds R4(config-if)#ip pim state-refresh origination-interval 8 R4(config-if)#^Z R4#sh *Mar 1 04:58:54.018: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip pim int Address Interface Ver/ Nbr Query DR DR Mode Count Intvl Prior 180.40.7.130 FastEthernet0/0 v2/D 1 30 1 180.40.7.130 R4#sh ip pim int  de FastEthernet0/0 is up, line protocol is up Internet address is 180.40.7.130/27 Multicast switching: fast Multicast packets in/out: 9/0 Multicast boundary: not set Multicast TTL threshold: 0 PIM: enabled PIM version: 2, mode: dense PIM DR: 180.40.7.130 (this system) PIM neighbor count: 1 PIM Hello/Query interval: 30 seconds PIM State-Refresh processing: enabled PIM State-Refresh origination: enabled, interval: 8 seconds PIM NBMA mode: disabled PIM ATM multipoint signalling: disabled PIM domain border: disabled Multicast Tagswitching: disabled R4#deb ip mp R4#deb ip mpacket ? Hostname or A.B.C.D IP group address detail Print IP header fields and MAC addresses fastswitch Print IP header fields on the fast path list Access-list R4#deb ip mpacket de R4#deb ip mpacket detail IP multicast packets debugging is on (detailed) R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#logg buff R4(config)#^Z R4# R4# R4# R4# R4# R4# *Mar 1 04:59:24.726: %SYS-5-CONFIG_I: Configured from console by console R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: . S6#ping 224.6.6.6 re 1000 Type escape sequence to abort. Sending 1000, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: RACK11AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh lof ^ % Invalid input detected at '^' marker. R4#sh lof g Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 39 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 19 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 26 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 04:59:24.726: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 04:59:32.054: IP(0): MAC sa=0012.7f8d.3ca1 (FastEthernet0/0), IP last-hop=180.40.7.129 *Mar 1 04:59:32.054: IP(0): IP tos=0x0, len=100, id=1, ttl=252, prot=1 *Mar 1 04:59:32.054: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.6.6.6 id=1, prot=1, len=114(100), mroute olist null *Mar 1 04:59:32.066: IP(0): MAC sa=0012.7f8d.3ca1 (FastEthernet0/0), IP last-hop=180.40.7.129 *Mar 1 04:59:32.066: IP(0): IP tos=0x0, len=100, id=1, ttl=252, prot=1 *Mar 1 04:59:32.066: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.6.6.6 id=1, prot=1, len=114(100), mroute olist null R4#deb ip pim PIM debugging is on R4#deb ip pim ? Hostname or A.B.C.D IP group address atm PIM ATM signalling activity auto-rp Auto-RP bsr PIM Candidate-RP/BSR activity df PIM RP designated forwarder election activity hello PIM Hello packets tag PIM multicast tagswitching activity vrf Select VPN Routing/Forwarding instance R4#deb ip pim             RACK11AS>6 [Resuming connection 6 to r6 ... ] .... S6#ping 224.6.6.6 re 1000  re 1000 7 re 1000 Type escape sequence to abort. Sending 1000, 100-byte ICMP Echos to 224.6.6.7, timeout is 2 seconds: RACK11AS>4 [Resuming connection 4 to r4 ... ] * prot=1 *Mar 1 05:00:20.158: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.6.6.7 id=21, prot=1, len=114(100), mroute olist null *Mar 1 05:00:20.210: PIM(0): Insert (180.40.7.97,224.6.6.7) prune in nbr 180.40.7.129's queue R4# R4# *Mar 1 05:00:20.210: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 05:00:20.210: PIM(0): Adding v2 (180.40.7.97/32, 224.6.6.7) Prune *Mar 1 05:00:20.210: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) R4#sh run int fa 0/0 Building configuration... Current configuration : 208 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 8 ip pim dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4#clea log Clear logging buffer [confirm] R4# R4# R4# R4# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#a ip access-list st No  Prob    NoGroup R7(config-std-nacl)#den 224.20.68.1 R7(config-std-nacl)#per any R7(config-std-nacl)#exit R7(config)#ip pim rp-add R7(config)#ip pim rp-address ? A.B.C.D IP address of Rendezvous-point for group R7(config)#ip pim rp-address 180.40.7.129 ? <1-99> Access-list reference for group <1300-1999> Access-list reference for group (expanded range) WORD IP Named Standard Access list override Overrides dynamically learnt RP mappings R7(config)#ip pim rp-address 180.40.7.129 NoGroup ? override Overrides dynamically learnt RP mappings R7(config)#ip pim rp-address 180.40.7.129 NoGroup R7(config)#exit R7#sh run *Mar 1 05:00:18.824: %SYS-5-CONFIG_I: Configured from console by console R7#sh run | b rp-add ip pim rp-address 180.40.7.129 NoGroup ! ip access-list standard NoGroup deny 224.20.68.1 permit any ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! --More--   R7# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip pim rp-address 180.40.7.129 NoGroup S5(config)#! S5(config)#ip access-list standard NoGroup S5(config-std-nacl)# deny 224.20.68.1 S5(config-std-nacl)# permit any S5(config-std-nacl)#! S5(config-std-nacl)#! S5(config-std-nacl)# RACK11AS>1 [Resuming connection 1 to r1 ... ] *Mar  shutdown --More--   R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pim rp-address 180.40.7.129 NoGroup R1(config)#! R1(config)#ip access-list standard NoGroup R1(config-std-nacl)# deny 224.20.68.1 R1(config-std-nacl)# permit any R1(config-std-nacl)#! R1(config-std-nacl)#! R1(config-std-nacl)#^Z R1# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sg lo    h log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 62 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 42 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 26 message lines logged --More--   Log Buffer (4096 bytes): R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 62 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 42 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 26 message lines logged --More--   Log Buffer (4096 bytes): R4# *Mar 1 05:03:22.138: IP(0): MAC sa=0012.7f8d.3ca1 (FastEthernet0/0), IP last-hop=180.40.7.129 *Mar 1 05:03:22.142: IP(0): IP tos=0x0, len=100, id=112, ttl=252, prot=1 *Mar 1 05:03:22.142: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.6.6.7 id=112, prot=1, len=114(100), mroute olist null *Mar 1 05:03:22.162: PIM(0): Insert (180.40.7.97,224.6.6.7) prune in nbr 180.40.7.129's queue *Mar 1 05:03:22.162: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 05:03:22.162: PIM(0): Adding v2 (180.40.7.97/32, 224.6.6.7) Prune *Mar 1 05:03:22.162: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) R4# R4# R4# R4# R4#clea o log Clear logging buffer [confirm] R4# R4# R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/1 R3(config-if)#ip pim ? bidir-neighbor-filter PIM bidir capable peering filter bsr-border Border of PIM domain dense-mode Enable PIM dense-mode operation dr-priority PIM router DR priority nbma-mode Use Non-Broadcast Multi-Access (NBMA) mode on interface neighbor-filter PIM peering filter query-interval PIM router query interval sparse-dense-mode Enable PIM sparse-dense-mode operation sparse-mode Enable PIM sparse-mode operation state-refresh PIM DM State-Refresh configuration version PIM version R3(config-if)#ip pim        ^Z R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#shg    log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 76 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 56 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 26 message lines logged --More--   Log Buffer (4096 bytes): R4# R4# R4# R4# R4#sh clock *05:06:06.730 UTC Mon Mar 1 1993 R4# *Mar 1 05:06:24.146: IP(0): MAC sa=0012.7f8d.3ca1 (FastEthernet0/0), IP last-hop=180.40.7.129 *Mar 1 05:06:24.146: IP(0): IP tos=0x0, len=100, id=203, ttl=252, prot=1 *Mar 1 05:06:24.146: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.6.6.7 id=203, prot=1, len=114(100), mroute olist null *Mar 1 05:06:24.162: PIM(0): Insert (180.40.7.97,224.6.6.7) prune in nbr 180.40.7.129's queue *Mar 1 05:06:24.162: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 05:06:24.162: PIM(0): Adding v2 (180.40.7.97/32, 224.6.6.7) Prune *Mar 1 05:06:24.162: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) R4#sh l cloc ck *05:06:40.646 UTC Mon Mar 1 1993 R4#u all All possible debugging has been turned off R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] .... S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim rp-address 180.40.7.129 NoGroup S6(config)#! S6(config)#ip access-list standard NoGroup S6(config-std-nacl)# deny 224.20.68.1 S6(config-std-nacl)# permit any S6(config-std-nacl)#! S6(config-std-nacl)#^Z S6# RACK11AS>2 [Resuming connection 2 to r2 ... ] * R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim rp-address 180.40.7.129 NoGroup R2(config)#! R2(config)#ip access-list standard NoGroup R2(config-std-nacl)# deny 224.20.68.1 R2(config-std-nacl)# permit any R2(config-std-nacl)#! R2(config-std-nacl)# *Mar 1 05:04:50.165: %PIM-6-INVALID_RP_JOIN: Received (*, 224.0.1.40) Join from 0.0.0.0 for invalid RP 180.40.7.129 R2(config-std-nacl)#^Z R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4# R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *M R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pim rp-address 180.40.7.129 NoGroup R3(config)#! R3(config)#ip access-list standard NoGroup R3(config-std-nacl)# deny 224.20.68.1 R3(config-std-nacl)# permit any R3(config-std-nacl)#! R3(config-std-nacl)#^Z R3# *Mar 1 05:04:56.375: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] 0 S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:59/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.4.4.4), 00:00:59/00:02:00, flags: P Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (*, 224.0.1.40), 00:01:08/00:03:13, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:17/00:03:12 FastEthernet0/1, Forward/Sparse-Dense, 00:01:09/00:01:51 Serial1/2, Forward/Sparse-Dense, 00:01:09/00:01:51 R3# cle ip mrout * R3# cle ip mrout *sh ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:00:02/00:02:57, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:00:02/00:02:57 R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute  cle ip mrout *sh ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:00:21/00:02:38, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:00:21/00:02:38 R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/1 R3(config-if)#ip pim de R3(config-if)#ip pim dense-mode p R3(config-if)#ip pim dense-mode proxy-register ? list Access list route-map Route-map R3(config-if)#ip pim dense-mode proxy-register lisdy ? % Unrecognized command R3(config-if)#ip pim dense-mode proxy-register lisdy     ? <100-199> Extended access list number <2000-2699> Extended access list number (expanded range) WORD IP named extended access list R3(config-if)#ip pim dense-mode proxy-register lis pRO   Prob9 ? R3(config-if)#ip pim dense-mode proxy-register lis Prob9 Warning: PIM register rate-limit set to 2 messages per second R3(config-if)#exit R3(config)#ip access R3(config)#ip access-list ex R3(config)#ip access-list extended Prob9 R3(config-ext-nacl)#per ip any any R3(config-ext-nacl)#^Z R3# *Mar 1 05:07:27.655: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:38/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.4.4.4), 00:00:02/00:02:58, flags: P Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (*, 224.0.1.40), 00:01:32/00:03:29, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:01:01/00:03:27 Serial1/2, Forward/Sparse-Dense, 00:01:33/00:01:27 R3#, 224.4.4.4), 00:00:59/stopped, RP 180.40.7.129, flags: SP ^ % Invalid input detected at '^' marker. R3# Incoming interface: Null, RPF nbr 0.0.0.0 ^ % Invalid input detected at '^' marker. R3# Outgoing interface list: Null ^ % Invalid input detected at '^' marker. R3# Outgoing interface list: Null ^ % Invalid input detected at '^' marker. R3# Outgoing interface list: NullIncoming interface: Null, RPF nbr 0.0.0.0, 224.4.4.4), 00:00:59/stopped, RP 180.40.7.129, flags: SPsh ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:46/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.4.4.4), 00:00:09/00:02:50, flags: P Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (*, 224.0.1.40), 00:01:39/00:03:21, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:01:08/00:03:20 Serial1/2, Forward/Sparse-Dense, 00:01:40/00:01:19 R3#   R3# R3# R3#conif t ^ % Invalid input detected at '^' marker. R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int     ^Z R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/4 S6(config-if)#sp S6(config-if)#spn S6(config-if)#spn an S6(config-if)#spanning-tree po S6(config-if)#spanning-tree portd f S6(config-if)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/4 but will only have effect when the interface is in a non-trunking mode. S6(config-if)#^Z S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#shut R4(config-if)#no shu *Mar 1 05:11:06.070: %PIM-5-NBRCHG: neighbor 180.40.7.129 DOWN on interface FastEthernet0/0 (vrf default) non DR *Mar 1 05:11:06.074: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#no shut R4(config-if)#^Z R4# *Mar 1 05:11:08.070: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 1 05:11:08.354: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 05:11:09.070: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:01:43/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.4.4.4), 00:01:06/00:01:53, flags: P Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (*, 224.0.1.40), 00:02:37/00:03:22, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:02:06/00:03:21 Serial1/2, Forward/Sparse-Dense, 00:02:38/00:00:22 R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:01:48/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.4.4.4), 00:01:11/00:01:49, flags: P Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (*, 224.0.1.40), 00:02:41/00:03:18, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:02:10/00:03:17 Serial1/2, Forward/Sparse-Dense, 00:02:42/00:00:18 R3#qclea ip          clea ip mrout * R3#clea ip mrout * *Mar 1 05:09:07.511: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.11 on FastEthernet0/1 from LOADING to FULL, Loading Done R3#clea ip mrout *sh ip mroute  IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:00:01/00:02:58, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:01/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:01/00:02:58 R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:00:05/00:02:54, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:05/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:05/00:02:54 R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] 0confi tp 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:09/stopped, RP 180.40.7.129, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:09/00:00:00 (180.40.7.97, 224.4.4.4), 00:00:09/00:02:59, flags: JT Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:09/00:00:00 (*, 224.0.1.40), 00:00:20/00:02:39, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:20/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:00:20/00:02:39 R3#sh run int fa 0/1 Building configuration... Current configuration : 144 bytes ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim dense-mode proxy-register list Prob9 duplex auto speed auto end R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh run int f a0/\ \     a0/0 Building configuration... Current configuration : 208 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 8 ip pim dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#in tlo 0 ^ % Invalid input detected at '^' marker. R4(config)#int  lo 0 R4(config-if)#ip addres 4.4.4.4 255.255.255.0 R4(config-if)# ip igmp join-group 224.4.4.4 R4(config-if)#int fa 0/0 R4(config-if)#no ip igmp join-group 224.4.4.4 R4(config-if)#^Z R4# *Mar 1 05:12:40.366: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:01:09/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.4.4.4), 00:01:09/00:01:59, flags: PJT Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null (*, 224.0.1.40), 00:01:19/00:02:45, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:46/00:02:43 FastEthernet0/1, Forward/Dense, 00:01:20/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:01:20/00:01:39 R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6#con    RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo 0 R4(config-if)#ip pim de R4(config-if)#ip pim dense-mode R4(config-if)#^Z R4# *Mar 1 05:14:24.858: %SYS-5-CONFIG_I: Configured from console by console R4# *Mar 1 05:14:25.882: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 4.4.4.4 on interface Loopback0 (vrf default) R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:02:55/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.4.4.4), 00:02:55/00:01:31, flags: JT Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:09/00:00:00 (*, 224.0.1.40), 00:03:05/00:02:56, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:02:32/00:02:55 FastEthernet0/1, Forward/Dense, 00:03:06/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:03:06/00:00:00 R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 48 ms Reply to request 0 from 180.40.7.130, 60 ms S6# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:03:15/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.4.4.4), 00:03:15/00:02:53, flags: JT Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:00:28/00:00:00 (*, 224.0.1.40), 00:03:25/00:02:37, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:02:51/00:02:36 FastEthernet0/1, Forward/Dense, 00:03:26/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:03:26/00:00:00 R3#sh urnu    run        sh run int fa 0/1 Building configuration... Current configuration : 144 bytes ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim dense-mode proxy-register list Prob9 duplex auto speed auto end R3# R3# R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:04:29/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.4.4.4), 00:04:29/00:01:39, flags: JT Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Dense, 00:01:43/00:00:00 (*, 224.0.1.40), 00:04:40/00:03:20, RP 180.40.7.129, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:04:06/00:03:19 FastEthernet0/1, Forward/Dense, 00:04:41/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:04:41/00:00:00 R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:21:38/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:01:50/00:00:00 FastEthernet0/0, Forward/Dense, 00:05:06/00:00:00 (180.40.7.97, 224.4.4.4), 00:01:31/00:01:36, flags: LT Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:01:33/00:00:00 (*, 224.0.1.40), 00:01:53/00:02:51, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:01:53/00:00:00 FastEthernet0/0, Forward/Dense, 00:01:53/00:00:00 R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b ip pimb ip pim  ipu ip pim ip pim i ip pim ip pim  pim  pim      rp-a add ip pim rp-address 180.40.7.129 NoGroup R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip pim rp-address 180.40.7.129 NoGroup R3(config)#^Z R3# RACK11AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#conf toi   Enter configuration commands, one per line. End with CNTL/Z. R1(config)#no ip pim rp-address 180.40.7.129 NoGroup R1(config)#^Z R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#no ip pim rp-address 180.40.7.129 NoGroup R2(config)#^Z R2# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5(config-std-nacl)#no ip pim rp-address 180.40.7.129 NoGroup S5(config)#^Z S5# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#no ip pim rp-address 180.40.7.129 NoGroup S6(config)#^Z S6# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#no ip pim rp-address 180.40.7.129 NoGroup R7(config)#^Z R7# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim R2(config)#ip pim se R2(config)#ip pim send-rp-d R2(config)#ip pim send-rp-discovery ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing scope Scope of the RP discovery packets R2(config)#ip pim send-rp-discovery scop R2(config)#ip pim send-rp-discovery scope ? <1-255> TTL R2(config)#ip pim send-rp-discovery scope 2 R2(config)#ip pim send-rp-discovery scope 2 ? R2(config)#ip pim send-rp-discovery scope 2                                  ^Z R2#sh run | *Mar 1 05:17:03.940: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | i send ip pim send-rp-discovery scope 2 R2# R2#^x3 % Unknown command or computer name, or unable to find computer address R2# R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pims se R3(config)#ip pims se       sen R3(config)#ip pim send-rp-a R3(config)#ip pim send-rp-announce ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config)#ip pim send-rp-announce fa 0/1 ? scope RP announcement scope R3(config)#ip pim send-rp-announce fa 0/1 sc R3(config)#ip pim send-rp-announce fa 0/1 scope ? <1-255> TTL of the RP announce packet R3(config)#ip pim send-rp-announce fa 0/1 scope 1 ? group-list Group access-list interval RP announcement interval R3(config)#ip pim send-rp-announce fa 0/1 scope 1 gr R3(config)#ip pim send-rp-announce fa 0/1 scope 1 group-list NoGroup ? interval RP announcement interval R3(config)#ip pim send-rp-announce fa 0/1 scope 1 group-list NoGroup in R3(config)#$-rp-announce fa 0/1 scope 1 group-list NoGroup interval ? <1-16383> number of seconds R3(config)#$-rp-announce fa 0/1 scope 1 group-list NoGroup interval 5 R3(config)#^Z R3# RACK11AS>6 [Resuming connection 6 to r6 ... ] 05: S6#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP Uptime: 00:00:07, expires: 00:02:49 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP Uptime: 00:00:07, expires: 00:02:50 S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp a map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4# RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar R7#sh ip pim m rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:48, expires: 00:02:09 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:48, expires: 00:02:12 R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3# RACK11AS>5 [Resuming connection 5 to r5 ... ] 05:18 S5#ash     sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:01:00, expires: 00:02:58 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:01:00, expires: 00:02:56 S5# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:27:18/00:02:10, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:07:29/00:00:00 FastEthernet0/0, Forward/Dense, 00:10:45/00:00:00 (*, 224.0.1.40), 00:07:31/00:02:13, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:07:32/00:00:00 FastEthernet0/0, Forward/Dense, 00:07:32/00:00:00 R4#sh ip mroutepim rp map PIM Group-to-RP Mappings R4# RACK11AS> [Resuming connection 4 to r4 ... ] R4#sh run int fa 0/0 Building configuration... Current configuration : 178 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 8 ip pim dense-mode duplex auto speed auto end R4#sh run int fa 0/0ip pim rp map  PIM Group-to-RP Mappings R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip pim rp mapconfi t p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 40 ms S6# S6# S6# S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp map PIM Group-to-RP Mappings R4# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#no ip pim rp-address 180.40.7.129 NoGroup!  permit anydeny 224.20.68.1permit any ! no ip pim rp-address 180.40.7.129 NoGroupip pim send-rp-discovery scope 2  3 R2(config)#^Z R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4# R4# R4# R4#sh    ship pi      ip pim map ^ % Invalid input detected at '^' marker. R4#\sh ip pim maprmappmap map PIM Group-to-RP Mappings R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#int fa 0/0 1 R3(config-if)#int fa 0/10$-rp-announce fa 0/1 scope 1 group-list NoGroup interval 5int fa 0/0           ip pim sp R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)#^Z R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:06, expires: 00:02:53 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:00:06, expires: 00:02:51 R4#sh ip int           sh ip pim int Address Interface Ver/ Nbr Query DR DR Mode Count Intvl Prior 180.40.7.130 FastEthernet0/0 v2/D 1 30 1 180.40.7.130 4.4.4.4 Loopback0 v2/D 0 30 1 4.4.4.4 R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:29:33/00:02:53, RP 180.40.7.129, flags: SJCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:09:45/00:00:00 (*, 224.0.1.40), 00:09:46/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:09:46/00:00:00 FastEthernet0/0, Forward/Dense, 00:09:47/00:00:00 (180.40.7.2, 224.0.1.40), 00:00:44/00:02:21, flags: LT Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:00:44/00:00:00 (180.40.7.35, 224.0.1.40), 00:00:44/00:02:21, flags: LT Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 --More--   Outgoing interface list: Loopback0, Forward/Dense, 00:01:18/00:00:00 R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:30:11/00:02:15, RP 180.40.7.129, flags: SJCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:10:23/00:00:00 (*, 224.0.1.40), 00:10:24/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:10:24/00:00:00 FastEthernet0/0, Forward/Dense, 00:10:26/00:00:00 (180.40.7.2, 224.0.1.40), 00:01:22/00:02:43, flags: LT Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:01:22/00:00:00 (180.40.7.35, 224.0.1.40), 00:01:22/00:02:43, flags: LT Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 --More--   R4#[Ash ip mroutepim intrp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:01:24, expires: 00:02:35 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.35 (?), elected via Auto-RP Uptime: 00:01:24, expires: 00:02:32 R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh run   | i ip    send ip pim send-rp-announce FastEthernet0/1 scope 1 group-list NoGroup interval 5 R3# R3#con   ^Z R3# RACK11AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip  int f e 0/0 R1(config-if)#ip ig R1(config-if)#ip igmp ? access-group IGMP group access group explicit-tracking Enable/Disable IGMP explicit-tracking helper-address IGMP helper address immediate-leave Leave groups immediately without sending last member query, use for one host network only join-group IGMP join multicast group last-member-query-count IGMP last member query count last-member-query-interval IGMP last member query interval limit IGMP limit mroute-proxy Mroute to IGMP proxy proxy-service Enable IGMP mroute proxy service querier-timeout IGMP previous querier timeout query-interval IGMP host query interval query-max-response-time IGMP max query response value static-group IGMP static multicast group unidirectional-link IGMP unidirectional link multicast routing v3lite Enable/disable IGMPv3 Lite version IGMP version R1(config-if)#ip igmp a R1(config-if)#ip igmp access-group ? <1-99> Access list number WORD IP Named Standard Access list R1(config-if)#ip igmp access-group                      exit R1(config)#ip pro   Prob6aProb6cProb6cProb6eProb6sProb6sProb6 Prob6sProb6tProb6 Prob6 R1(config-std-nacl)#per 224.20.73.1 15.128.20.0 R1(config-std-nacl)#int e 0/0 R1(config-if)#\ ip ig R1(config-if)#ip igmp a R1(config-if)#ip igmp access-group Prob6 ? R1(config-if)#ip igmp access-group Prob6 R1(config-if)#^Z R1#^x *Mar 1 05:31:43.426: %SYS-5-CONFIG_I: Configured from console by console R1#^x5 % Unknown command or computer name, or unable to find computer address R1# R1# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/1 S5(config-if)#ip ig S5(config-if)#ip igmp j S5(config-if)#ip igmp join-group 224.14 8\  48/ .93.1 S5(config-if)# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip access Standard IP access list NoGroup 10 deny 224.20.68.1 20 permit any (197 matches) Standard IP access list Prob6 10 permit 224.20.73.1, wildcard bits 15.128.20.0 (1 match) R1#sdh     sh run | b 0/0 interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip igmp access-group Prob6 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 102 ! interface Ethernet0/1 --More--   R1#sh run | b 0/0 interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip igmp access-group Prob6 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 102 ! interface Ethernet0/1 --More--   ip address 17.100.1.1 255.255.255.0 ip pim sparse-dense-mode half-duplex no keepalive ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! ! ! ip access-list standard NoGroup deny 224.20.68.1 permit any ip access-list standard Prob6 permit 224.20.73.1 15.128.20.0 --More--  ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1# R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/0 R1(config-if)#ip mu R1(config-if)#ip multicast r R1(config-if)#ip multicast rate-limit ? in Rate limit incoming packets out Rate limit outgoing packets R1(config-if)#ip multicast rate-limit in ? <0-4294967> Rate in kilobits per second group-list Rate limit for groups source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit in vi ? <0-4294967> Rate in kilobits per second R1(config-if)#ip multicast rate-limit in vi 80 ? R1(config-if)#ip multicast rate-limit in vi 80                                  exit R1(config)#ip acces        exitint e 0/0 R1(config-if)#ip mu R1(config-if)#ip multicast r R1(config-if)#ip multicast rate-limit l R1(config-if)#ip multicast rate-limit l g R1(config-if)#ip multicast rate-limit grr  R1(config-if)#ip multicast rate-limit gr    ? in Rate limit incoming packets out Rate limit outgoing packets R1(config-if)#ip multicast rate-limit in ? <0-4294967> Rate in kilobits per second group-list Rate limit for groups source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit in gr  R1(config-if)#ip multicast rate-limit in gr / ? <1-99> Multicast group access-list reference <1300-1999> Multicast group access-list reference (expanded range) WORD IP Named Standard Access list R1(config-if)#ip multicast rate-limit in gr                               exit R1(config)#ip p access-lo  st Prob7 R1(config-std-nacl)#per 239.0.0.09  0.255.255.255 R1(config-std-nacl)#int e 0/0 R1(config-if)#ip mu R1(config-if)#ip multicast r R1(config-if)#ip multicast rate-limit in g R1(config-if)#ip multicast rate-limit in group-list Prob7 ? <0-4294967> Rate in kilobits per second source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit in group-list Prob7 vi ? <0-4294967> Rate in kilobits per second R1(config-if)#ip multicast rate-limit in group-list Prob7 vi 80 R1(config-if)#exi R1(config)#ip s R1(config)#ip sa R1(config)#ip sap ? cache-timeout Timeout period for entries R1(config)#ip sap        int e 0/0 R1(config-if)#ip sap ? listen Listen for sap packets on interface R1(config-if)#ip sap l R1(config-if)#ip sap listen ? R1(config-if)#ip sap listen R1(config-if)#^Z R1# *Mar 1 05:36:23.746: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int     | b int   0/0 interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip multicast rate-limit in group-list Prob7 video 80 ip igmp access-group Prob6 ip sap listen half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 102 --More--  ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim sparse-dense-mode half-duplex no keepalive ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! ! ! ip access-list standard NoGroup deny 224.20.68.1 permit any --More--  ip access-list standard Prob6 permit 224.20.73.1 15.128.20.0 ip access-list standard Prob7 permit 239.0.0.0 0.255.255.255 ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R1# R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/1 R1(config-if)#ip ? Interface IP configuration subcommands: access-group Specify access control for packets accounting Enable IP accounting on this interface address Set the IP address of an interface authentication authentication subcommands bandwidth-percent Set EIGRP bandwidth limit bgp BGP interface commands broadcast-address Set the broadcast address of an interface cef Cisco Express Forwarding interface commands cgmp Enable/disable CGMP dhcp Configure DHCP parameters for this interface directed-broadcast Enable forwarding of directed broadcasts dvmrp DVMRP interface commands flow NetFlow related commands hello-interval Configures IP-EIGRP hello interval helper-address Specify a destination address for UDP broadcasts hold-time Configures IP-EIGRP hold time idle-group Specify interesting packets for idle-timer igmp IGMP interface commands information-reply Enable sending ICMP Information Reply messages irdp ICMP Router Discovery Protocol load-sharing Style of load sharing --More--   local-proxy-arp Enable local-proxy ARP mask-reply Enable sending ICMP Mask Reply messages mobile Mobile IP support mrm Configure IP Multicast Routing Monitor tester mroute-cache Enable switching cache for incoming multicast packets mtu Set IP Maximum Transmission Unit multicast IP multicast interface commands nat NAT interface commands nbar Network-Based Application Recognition next-hop-self Configures IP-EIGRP next-hop-self nhrp NHRP interface subcommands ospf OSPF interface commands pgm PGM Reliable Transport Protocol pim PIM interface commands policy Enable policy routing proxy-arp Enable proxy ARP rarp-server Enable RARP server for static arp entries redirects Enable sending ICMP Redirect messages rgmp Enable/disable RGMP rip Router Information Protocol route-cache Enable fast-switching cache for outgoing packets router IP router interface commands rsvp RSVP Interface Commands --More--   R1(config-if)#ip pim R1(config-if)#ip pim ? bidir-neighbor-filter PIM bidir capable peering filter bsr-border Border of PIM domain dense-mode Enable PIM dense-mode operation dr-priority PIM router DR priority nbma-mode Use Non-Broadcast Multi-Access (NBMA) mode on interface neighbor-filter PIM peering filter query-interval PIM router query interval sparse-dense-mode Enable PIM sparse-dense-mode operation sparse-mode Enable PIM sparse-mode operation state-refresh PIM DM State-Refresh configuration version PIM version R1(config-if)#ip pim q R1(config-if)#ip pim query-interval ? <1-65535> Query interval in seconds or milliseconds R1(config-if)#ip pim query-interval 90 R1(config-if)#do sh ip pin int e 0/1 de sh ip pin int e 0/1 de ^ % Invalid input detected at '^' marker. R1(config-if)#do sh ip pin int e 0/1 de int e 0/1 de m int e 0/1 de Ethernet0/1 is up, line protocol is up Internet address is 17.100.1.1/24 Multicast switching: fast Multicast packets in/out: 1/24 Multicast boundary: not set Multicast TTL threshold: 0 PIM: enabled PIM version: 2, mode: sparse-dense PIM DR: 17.100.1.2 PIM neighbor count: 1 PIM Hello/Query interval: 90 seconds PIM State-Refresh processing: enabled PIM State-Refresh origination: disabled PIM NBMA mode: disabled PIM ATM multipoint signalling: disabled PIM domain border: disabled Multicast Tagswitching: disabled R1(config-if)#do sh ip igmp int e 0/1 Ethernet0/1 is up, line protocol is up Internet address is 17.100.1.1/24 IGMP is enabled on interface Current IGMP host version is 2 Current IGMP router version is 2 IGMP query interval is 60 seconds IGMP querier timeout is 120 seconds IGMP max query response time is 10 seconds Last member query count is 2 Last member query response interval is 1000 ms Inbound IGMP access group is not set IGMP activity: 1 joins, 0 leaves Multicast routing is enabled on interface Multicast TTL threshold is 0 Multicast designated router (DR) is 17.100.1.2 IGMP querying router is 17.100.1.1 (this system) No multicast groups joined by this system R1(config-if)#ip ig R1(config-if)#ip igmp q R1(config-if)#ip igmp quer? querier-timeout query-interval query-max-response-time R1(config-if)#ip igmp query-int R1(config-if)#ip igmp query-interval ? <1-18000> Query interval in seconds R1(config-if)#ip igmp query-interval 90 R1(config-if)#^Z R1#sh r *Mar 1 05:39:15.800: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int e 9 0/1 Building configuration... Current configuration : 172 bytes ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim query-interval 90 ip pim sparse-dense-mode ip igmp query-interval 90 half-duplex no keepalive end R1# R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#do sh run | i send ip pim send-rp-discovery scope 3 R2(config)#no ip pim send-rp-discovery scope 3 R2(config)#ip bs R2(config)#ip bs  pim bs R2(config)#ip pim bsr-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config)#ip pim bsr-candidate fa 0/1 ? <0-32> Hash Mask length for RP selection R2(config)#ip pim bsr-candidate fa 0/1 R2(config)#^Z R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#do sh run | i send ip pim send-rp-announce FastEthernet0/1 scope 1 group-list NoGroup interval 5 R3(config)#no ip pim send-rp-announce FastEthernet0/1 scope 1 group-list NoGr$end-rp-announce FastEthernet0/1 scope 1 group-list NoGro up inte R3(config)#$end-rp-announce FastEthernet0/1 scope 1 group-list NoGroup inteno ip pim send-rp-announce FastEthernet0/1 scope 1 group-list NoGro$ ip   pi R3(config)#ip pim rp- R3(config)#ip pim rp-ca R3(config)#ip pim rp-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config)#ip pim rp-candidate fa 0/1 ? group-list group-list interval RP candidate advertisement interval priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 grou R3(config)#ip pim rp-candidate fa 0/1 group-list NoGroup ? interval RP candidate advertisement interval priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 group-list NoGroup in R3(config)#ip pim rp-candidate fa 0/1 group-list NoGroup interval 5 R3(config)#^Z R3# *Mar 1 05:43:35.577: %SYS-5-CONFIG_I: RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP, via bootstrap, priority 0 Uptime: 00:25:33, expires: 00:01:11 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP Uptime: 00:25:33, expires: 00:01:15 S6#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP, via bootstrap, priority 0 Uptime: 00:25:41, expires: 00:01:03 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP Uptime: 00:25:41, expires: 00:01:06 S6#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP, via bootstrap, priority 0 Uptime: 00:25:43, expires: 00:01:01 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.98 (?), elected via Auto-RP Uptime: 00:25:43, expires: 00:01:05 S6#cel ip       lea ip pim rp ? A.B.C.D RP address S6#clea ip pim rp S6#clea ip pim rp sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6# S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#^x2 % Unknown command or computer name, or unable to find computer address S6# S6# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh ip pi im rp map PIM Group-to-RP Mappings This system is the Bootstrap Router (v2) Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.3 (?), via bootstrap, priority 0, holdtime 17 Uptime: 00:01:07, expires: 00:00:14 R2# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#^x2sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings S6#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0 Uptime: 00:00:00, expires: 00:03:26 S6# S6# S6# S6# S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim map rp      rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:14, expires: 00:03:12 R1# R1# R1# R1# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:22, expires: 00:03:04 R4# R4# R4# R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:01:29/00:02:24, RP 180.40.7.129, flags: SJCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:01:29/00:00:00 (*, 224.0.1.40), 00:34:22/00:02:24, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:34:22/00:00:00 FastEthernet0/0, Forward/Dense, 00:34:23/00:00:00 R4#   RACK11AS>6 [Resuming connection 6 to r6 ... ] pi 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 40 ms S6# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh run \ | i bsr ip pim bsr-candidate FastEthernet0/1 0 R2# R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] from console by console R3 R3#sh run | i rp-can ip pim rp-candidate FastEthernet0/1 group-list NoGroup interval 5 R3# R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pim ? accept-register Registers accept filter accept-rp RP accept filter autorp Configure AutoRP global operations bidir-enable Enable Bidir-PIM bsr-candidate Candidate bootstrap router (candidate BSR) log-neighbor-changes Log PIM neighbor up/down and DR changes register-rate-limit Rate limit for PIM data registers register-source Source address for PIM Register rp-address PIM RP-address (Rendezvous Point) rp-announce-filter Auto-RP announce message filter rp-candidate To be a PIMv2 RP candidate send-rp-announce Auto-RP send RP announcement send-rp-discovery Auto-RP send RP discovery message (as RP-mapping agent) spt-threshold Source-tree switching threshold ssm Configure Source Specific Multicast state-refresh PIM DM State-Refresh configuration vrf Select VPN Routing/Forwarding instance R3(config)#ip pim sp R3(config)#ip pim spt-threshold ? <0-4294967> Traffic rate in kilobits per second infinity Never switch to source-tree R3(config)#ip pim spt-threshold 1 ? group-list Group address access-list R3(config)#ip pim spt-threshold 1 R3(config)#^Z R3# *Mar 1 05:48:51.856: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pim spt-threshold 1 R1(config)#end R1# *Mar 1 05:50:05.954: %SYS-5-CONFIG_I: Configured from console by console R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim spt-threshold 1 R2(config)#end R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip pim spt-threshold 1 R4(config)#end R4# *Mar 1 05:51:38.92 RACK11AS>5 [Resuming connection 5 to r5 ... ] S5(config-if)#confi t ^ % Invalid input detected at '^' marker. S5(config-if)#ip pim spt-threshold 1 S5(config)#end S5# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim spt-threshold 1 S6(config)#end S6# RACK11AS>7 [Resuming connection 7 to r7 ... ] *M R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip pim spt-threshold 1 R7(config)#end R7# *Mar 1 05:49:32.851: %SYS-5-CONFIG_I: Configured from console by console R7# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pim bi R1(config)#ip pim bidir-enable R1(config)# R1# *Mar 1 05:51:04.594: %SYS-5-CONFIG_I: Configured from console by console R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] * R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#ip pim bidir-enable R2(config)# R2(config)# R2(config)#end R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] S-5-CONFIG_I: Configu R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#ip pim bidir-enable R4(config)# R4(config)# R4(config)#end R4# *Mar 1 05 RACK11AS>5 [Resuming connection 5 to r5 ... ] 05:52:23: %confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#ip pim bidir-enable S5(config)# S5(config)# S5(config)#end S5# RACK11AS>6 [Resuming connection 6 to r6 ... ] 05:5 S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#ip pim bidir-enable S6(config)# S6(config)# S6(config)#end S6# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#ip pim bidir-enable R7(config)# R7(config)# R7(config)#end R7# *Mar 1 05:50:41.215: %SYS-5-CONFIG_I: Configured from console by console R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3# R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#ip pim bidir-enable R3(config)# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#sh run | i ip pim ip pim sparse-dense-mode ip pim bidir-enable ip pim spt-threshold 1 R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:05:20, expires: 00:03:07 R7#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:35:50/00:02:22, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:35:50/00:00:00 R7#   RACK11AS> [Resuming connection 7 to r7 ... ] R7#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 124 ms Reply to request 0 from 180.40.7.130, 136 ms R7# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.148.93.1), 00:01:17/00:03:23, RP 180.40.7.129, flags: SC Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:01:04/00:03:23 (*, 224.4.4.4), 00:00:10/stopped, RP 180.40.7.129, flags: SP Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null (17.100.1.2, 224.4.4.4), 00:00:11/00:02:50, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:00:09/00:03:20 (*, 224.0.1.40), 00:36:29/00:04:21, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:36:29/00:00:00 --More--   Serial0/0.1, Forward/Sparse-Dense, 00:36:29/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 00:36:30/00:00:00 Ethernet0/0, Forward/Sparse-Dense, 00:36:30/00:00:00 (*, 224.2.127.254), 00:01:36/00:03:09, RP 180.40.7.129, flags: SCL Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:00:20/00:03:09 (*, 239.255.255.255), 00:01:36/00:03:07, RP 180.40.7.129, flags: SCL Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:00:22/00:03:07 R1# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config)#ip pim bidir-enablespt-threshold 1 rp-candidate fa 0/1 group-list NoGroup interval 5 ? bidir Group range treated in bidirectional shared-tree mode priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 group-list NoGroup interval 5 bi R3(config)#ip pim rp-candidate fa 0/1 group-list NoGroup interval 5 bidir R3(config)# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.4.4.4sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:36:33/00:02:54, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:36:33/00:00:00 R7#qsh ip mroutep 224.4.4.4 sh ip mroutepim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:06:19, expires: 00:03:13 R7#sh ip pim rp mapmroute p 224.4.4.4  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#p 224.4.4.4 p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.148.93.1), 00:00:30/00:02:49, RP 180.40.7.129, flags: BC Bidir-Upstream: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/0, Forward/Sparse-Dense, 00:00:29/00:03:05 Serial0/0.2, Bidir-Upstream/Sparse-Dense, 00:00:30/00:00:00 (*, 224.4.4.4), 00:00:12/00:02:53, RP 180.40.7.129, flags: BP Bidir-Upstream: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Serial0/0.2, Bidir-Upstream/Sparse-Dense, 00:00:14/00:00:00 (*, 224.0.1.40), 00:37:17/00:03:58, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:37:17/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 00:37:17/00:00:00 Ethernet0/1, Forward/Sparse-Dense, 00:37:17/00:00:00 Ethernet0/0, Forward/Sparse-Dense, 00:37:17/00:00:00 --More--   R1# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config)#sh ip mroute ^ % Invalid input detected at '^' marker. R3(config)#sh ip mroutedsh ip mrouteosh ip mroute sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.148.93.1), 00:00:40/00:02:49, RP 180.40.7.129, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:40/00:02:49 (*, 224.4.4.4), 00:00:44/00:02:15, RP 180.40.7.129, flags: BP Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.0.1.40), 00:37:40/00:02:15, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:37:41/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:37:41/00:00:00 Serial1/2, Forward/Sparse-Dense, 00:37:41/00:00:00 (*, 224.2.127.254), 00:00:42/00:02:47, RP 180.40.7.129, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 --More--   Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:44/00:02:46 (*, 239.255.255.255), 00:00:44/00:02:46, RP 180.40.7.129, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:44/00:02:46 R3(config)# RACK11AS>4 [Resuming connection 4 to r4 ... ] 5.874: %SYS-5-CONFIG_ R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:58/00:02:49, RP 180.40.7.129, flags: BCL Bidir-Upstream: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:00:58/00:02:49 FastEthernet0/0, Bidir-Upstream/Dense, 00:00:58/00:00:00 (*, 224.0.1.40), 00:40:56/00:02:48, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:40:57/00:00:00 FastEthernet0/0, Forward/Dense, 00:40:57/00:00:00 R4# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 117 ms R7# R7# R7# R7# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3(config)#^Z R3#sh run | *Mar 1 05:53:34.655: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | i ip    rp-can ip pim rp-candidate FastEthernet0/1 group-list NoGroup interval 5 bidir R3# R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip dhcp po R2(config)#ip dhcp pool ? WORD Pool name R2(config)#ip dhcp pool test R2(dhcp-config)#? DHCP pool configuration commands: accounting Send Accounting Start/Stop messages bootfile Boot file name client-identifier Client identifier client-name Client name default-router Default routers dns-server DNS servers domain-name Domain name exit Exit from DHCP pool configuration mode hardware-address Client hardware address host Client IP address and mask import Programatically importing DHCP option parameters lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network number and mask next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options origin Configure the origin of the pool subnet Subnet allocation commands update Dynamic updates --More--   R2(dhcp-config)#net R2(dhcp-config)#netw R2(dhcp-config)#network 180.40.7.96 /27 R2(dhcp-config)# RACK11AS>6 [Resuming connection 6 to r6 ... ] 05:5 S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#do deb dhcp ev deb dhcp ev ^ % Invalid input detected at '^' marker. S6(config)#^Z S6#deb dh 06:00:16: %SYS-5-CONFIG_I: Configured from console by console S6#deb dhcp ? detail DHCP packet content S6#deb dhcp de S6#deb dhcp detail DHCP client activity debugging is on (detailed) S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/2 S6(config-if)#ip    do sh run int f a0/2a0/2  Building configuration... Current configuration : 114 bytes ! interface FastEthernet0/2 no switchport ip address 180.40.7.97 255.255.255.224 ip pim sparse-dense-mode end S6(config-if)#ip add h dhcp S6(config-if)# 06:01:09: DHCP: DHCP client process started: 10 06:01:09: RAC: Starting DHCP discover on FastEthernet0/2 06:01:09: DHCP: Try 1 to acquire address for FastEthernet0/2 06:01:09: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/2 from FULL to DOWN, Neighbor Down: Interface down or detached 06:01:14: DHCP: allocate request 06:01:14: DHCP: new entry. add to queue 06:01:14: DHCP: SDiscover attempt # 1 for entry: 06:01:14: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/2 06:01:14: Temp sub net mask: 0.0.0.0 06:01:14: DHCP Lease server: 0.0.0.0, state: 1 Selecting 06:01:14: DHCP transaction id: 1E20 06:01:14: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs 06:01:14: Next timer fires after: 00:00:03 06:01:14: Retry count: 1 Client-ID: cisco-000a.f49a.2380-Fa0/2 06:01:14: Hostname: S6 06:01:14: DHCP: SDiscover: sending 294 byte length DHCP packet 06:01:14: DHCP: SDiscover 294 bytes 06:01:14: B'cast on FastEthernet0/2 interface from 0.0.0.0 06:01:16: DHCP: Received a BOOTREP pkt 06:01:16: DHCP: Scan: Message type: DHCP Offer 06:01:16: DHCP: Scan: Server ID Option: 180.40.7.98 = B4280762 06:01:16: DHCP: Scan: Lease Time: 86400 06:01:16: DHCP: Scan: Renewal time: 43200 06:01:16: DHCP: Scan: Rebind time: 75600 06:01:16: DHCP: Scan: Subnet Address Option: 255.255.255.224 06:01:16: DHCP: rcvd pkt source: 180.40.7.98, destination: 255.255.255.255 06:01:16: UDP sport: 43, dport: 44, length: 308 06:01:16: DHCP op: 2, htype: 1, hlen: 6, hops: 0 06:01:16: DHCP server identifier: 180.40.7.98 06:01:16: xid: 1E20, secs: 0, flags: 8000 06:01:16: client: 0.0.0.0, your: 180.40.7.97 06:01:16: srvr: 0.0.0.0, gw: 0.0.0.0 06:01:16: options block length: 60 06:01:16: DHCP Offer Message Offered Address: 180.40.7.97 06:01:16: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 06:01:16: DHCP: Server ID Option: 180.40.7.98 06:01:16: DHCP: offer received from 180.40.7.98 06:01:16: DHCP: SRequest attempt # 1 for entry: 06:01:16: Temp IP addr: 180.40.7.97 for peer on Interface: FastEthernet0/2 06:01:16: Temp sub net mask: 255.255.255.224 06:01:16: DHCP Lease server: 180.40.7.98, state: 2 Requesting 06:01:16: DHCP transaction id: 1E20 06:01:16: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs 06:01:16: Next timer fires after: 00:00:02 06:01:16: Retry count: 1 Client-ID: cisco-000a.f49a.2380-Fa0/2 06:01:16: Hostname: S6 06:01:16: DHCP: SRequestInterface FastEthernet0/2 assigned DHCP address 180.40.7.97, mask 255.255.255.224 - Server ID option: 180.40.7.98 06:01:16: DHCP: SRequest- Requested IP addr option: 180.40.7.97 06:01:16: DHCP: SRequest placed lease len option: 86400 06:01:16: DHCP: SRequest: 312 bytes 06:01:16: DHCP: SRequest: 312 bytes 06:01:16: B'cast on FastEthernet0/2 interface from 0.0.0.0 06:01:16: DHCP: Received a BOOTREP pkt 06:01:16: DHCP: Scan: Message type: DHCP Ack 06:01:16: DHCP: Scan: Server ID Option: 180.40.7.98 = B4280762 06:01:16: DHCP: Scan: Lease Time: 86400 06:01:16: DHCP: Scan: Renewal time: 43200 06:01:16: DHCP: Scan: Rebind time: 75600 06:01:16: DHCP: Scan: Subnet Address Option: 255.255.255.224 06:01:16: DHCP: rcvd pkt source: 180.40.7.98, destination: 255.255.255.255 06:01:16: UDP sport: 43, dport: 44, length: 308 06:01:16: DHCP op: 2, htype: 1, hlen: 6, hops: 0 06:01:16: DHCP server identifier: 180.40.7.98 06:01:16: xid: 1E20, secs: 0, flags: 8000 06:01:16: client: 0.0.0.0, your: 180.40.7.97 06:01:16: srvr: 0.0.0.0, gw: 0.0.0.0 06:01:16: options block length: 60 06:01:16: DHCP Ack Message 06:01:16: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 06:01:16: DHCP: Server ID Option: 180.40.7.98 06:01:19: DHCP: Releasing ipl options: 06:01:19: DHCP: Applying DHCP options: 06:01:19: DHCP Client Pooling: ***Allocated IP address: 180.40.7.97 06:01:19: Allocated IP address = 180.40.7.97 255.255.255.224 06:01:28: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/2 from LOADING to FULL, Loading Done RACK11AS>2 [Resuming connection 2 to r2 ... ] *Ma R2(dhcp-config)#do sh ip dhcp bin % Ambiguous command: "do sh ip dhcp bin" R2(config)#do sh ip dhcp bind Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.97 0063.6973.636f.2d30. Mar 02 1993 05:58 AM Automatic 3030.612e.6634.3961. 2e32.3338.302d.4661. 302f.32 R2(config)# *Mar 1 05:59:50.123: %PIM-5-NBRCHG: neighbor 0.0.0.0 DOWN on interface FastEthernet0/1 (vrf default) non DR R2(config)#no ip dhcp pool tgest    est R2(config)#ip dhcp pool S6 R2(dhcp-config)#cli R2(dhcp-config)#client-i R2(dhcp-config)#client-identifier 0063.6973.636f.2d30.3030.612e.6634.3961.2e3$tifier 0063.6973.636f.2d30.3030.612e.6634.3961.2e32 .3338.3023.6973.636f.2d30.3030.612e.6634.3961.2e32.3338.302d .4661.302f.2d30.3030.612e.6634.3961.2e32.3338.302d.4661.302f .32 R2(dhcp-config)#hoy   st 180.40.7.97 /27 R2(dhcp-config)#exit R2(config)#int fa 0/2 1 R2(config-if)#ip mu R2(config-if)#ip multicast h R2(config-if)#ip multicast helper-map ? A.B.C.D IP multicast address broadcast Broadcast address R2(config-if)#ip multicast helper-map broad R2(config-if)#ip multicast helper-map broadcast ? A.B.C.D IP address R2(config-if)#ip multicast helper-map broadcast 226.6.6.6 ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R2(config-if)#ip multicast helper-map broadcast 226.6.6.6 Prob12 ? R2(config-if)#ip multicast helper-map broadcast 226.6.6.6 Prob12 R2(config-if)#exit R2(config)#ip access R2(config)#ip access-list ex R2(config)#ip access-list extended Prob12 R2(config-ext-nacl)#per 180.40.7.97 h180.40.7.97 o180.40.7.97 s180.40.7.97 t180.40.7.97  180.40.7.97 180.40.7.97 uhost 180.40.7.97 dhost 180.40.7.97 phost 180.40.7.97  host 180.40.7.97 host 180.40.7.97 host 255.255.255.255 eq tftp R2(config-ext-nacl)#^Z R2# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip access-list ex Prob9 R1(config-ext-nacl)#per udp host 180.40.7.97 any eq 69 R1(config-ext-nacl)#int s 0/90  0.1 R1(config-subif)#shut R1(config-subif)# *Mar 1 06:08:03.448: %PIM-5-NBRCHG: neighbor 180.40.7.33 DOWN on interface Serial0/0.1 (vrf default) non DR R1(config-subif)#shutint s 0/0.1 2 R1(config-subif)#ip mu R1(config-subif)#ip multicast h R1(config-subif)#ip multicast helper-map ? A.B.C.D IP multicast address broadcast Broadcast address R1(config-subif)#ip multicast helper-map 226.6.6.6 ? A.B.C.D IP address R1(config-subif)#ip multicast helper-map 226.6.6.6 17.100.1.255 ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R1(config-subif)#ip multicast helper-map 226.6.6.6 17.100.1.255 Prob9 ? R1(config-subif)#ip multicast helper-map 226.6.6.6 17.100.1.255 Prob9 R1(config-subif)# RACK11AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#logg buff R7(config)#^Z R7#deb ip *Mar 1 06:08:10.587: %SYS-5-CONFIG_I: Configured from console by console R7#deb ip pack de IP packet debugging is on (detailed) R7# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6(config-if)#^Z S6# 06:11:26: %SYS-5-CONFIG_I: Configured from console by consolecopy tftp run Address or name of remote host []? 255.255.255.255 Source filename []? test Destination filename [running-config]? Accessing tftp://255.255.255.255/test... RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar R7# *Mar 1 06:08:33.016: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 06:08:33.473: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 R7# *Mar 1 06:08:37.419: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 06:08:42.680: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 06:08:43.016: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7#do sh    *Mar 1 06:08:45.180: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 64, sending broad/multicast, proto=89 R7#do s    dh *Mar 1 06:08:47.420: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7#dh    sh log Syslog logging: enabled (9 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 89 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 37 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 59 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 06:08:10.587: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 06:08:17.418: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 *Mar 1 06:08:23.016: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 06:08:27.419: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 *Mar 1 06:08:33.016: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 06:08:33.473: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 *Mar 1 06:08:37.419: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 *Mar 1 06:08:42.680: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 06:08:43.016: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 *Mar 1 06:08:45.180: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 64, sending broad/multicast, proto=89 *Mar 1 06:08:47.420: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 06:08:51.050: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 56, rcvd 0, proto=103 R7# *Mar 1 06:08:53.017: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7#q  RACK11AS>1 [Resuming connection 1 to r1 ... ] R1(config-subif)#do sh int e 0/1 Ethernet0/1 is up, line protocol is up Hardware is AmdP2, address is 0050.7358.c201 (bia 0050.7358.c201) Internet address is 17.100.1.1/24 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:07, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 3679 packets input, 406006 bytes, 0 no buffer Received 3665 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 3061 packets output, 381782 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier --More--   R1(config-subif)#[Ado sh int e 0/1iint e 0/1pint e 0/1 int e 0/1 Ethernet0/1 is up, line protocol is up Internet address is 17.100.1.1/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Multicast reserved groups joined: 224.0.0.5 224.0.0.6 224.0.0.1 224.0.0.2 224.0.0.22 224.0.0.13 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF Fast switching turbo vector --More--   R1(config-subif)#n int e 0/1 R1(config-if)#ip di R1(config-if)#ip directed-broadcast R1(config-if)# RACK11AS>6 [Resuming connection 6 to r6 ... ] % S6#test255.255.255.255copy tftp run  Address or name of remote host [255.255.255.255]? Source filename [test]? Destination filename [running-config]? Accessing tftp://255.255.255.255/test... RACK11AS>7 [Resuming connection 7 to r7 ... ] *Mar d=255.255.255.255, len 41, rcvd 2 *Mar 1 06:09:45.459: UDP src=51970, dst=69 R7# R7# *Mar 1 06:09:47.422: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 06:09:49.457: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 41, rcvd 2 *Mar 1 06:09:49.457: UDP src=51970, dst=69 R7# *Mar 1 06:09:51.180: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 56, rcvd 0, proto=103 R7# *Mar 1 06:09:53.019: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# *Mar 1 06:09:54.457: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 41, rcvd 2 *Mar 1 06:09:54.457: UDP src=51970, dst=69 R7#u all All possible debugging has been turned off R7# *Mar 1 06:09:57.422: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)#^Z R1#sh run *Mar 1 06:11:56.234: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b 0/0.2 interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map 226.6.6.6 17.100.1.255 Prob9 ip ospf network point-to-multipoint frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip directed-broadcast ip pim query-interval 90 ip pim sparse-dense-mode ip igmp query-interval 90 half-duplex no keepalive ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 --More--  ! no ip http server ip classless ! ip pim bidir-enable ip pim spt-threshold 1 ! ! ip access-list standard NoGroup deny 224.20.68.1 permit any ip access-list standard Prob6 permit 224.20.73.1 15.128.20.0 ip access-list standard Prob7 permit 239.0.0.0 0.255.255.255 ! ip access-list extended Prob9 permit udp host 180.40.7.97 any eq tftp ! ! ! ! ! --More--   R1# RACK11AS>6 [Resuming connection 6 to r6 ... ] %Er S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/2 S6(config-if)# ip address 180.40.7.97 255.255.255.224 06:14:55: DHCP: SRelease attempt # 1 for entry: 06:14:55: Temp IP addr: 180.40.7.97 for peer on Interface: FastEthernet0/2 06:14:55: Temp sub net mask: 255.255.255.224 06:14:55: DHCP Lease server: 180.40.7.98, state: 7 Releasing 06:14:55: DHCP transaction id: 1E20 06:14:55: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs 06:14:55: Next timer fires after: 00:00:00 06:14:55: Retry count: 1 Client-ID: cisco-000a.f49a.2380-Fa0/2 06:14:55: Hostname: S6 06:14:55: DHCP: SRelease placed Server ID option: 180.40.7.98 06:14:55: DHCP: SRelease: 279 bytes 06:14:55: DHCP: SRelease attempt # 2 for entry: 06:14:55: Temp IP addr: 180.40.7.97 for peer on Interface: FastEthernet0/2 06:14:55: Temp sub net mask: 255.255.255.224 06:14:55: DHCP Lease server: 180.40.7.98, state: 7 Releasing 06:14:55: DHCP transaction id: 1E20 06:14:55: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs 06:14:55: Next timer fires after: 00:00:00 06:14:55: Retry count: S6(config-if)#^Z S6# 2 Client-ID: cisco-000a.f49a.2380-Fa0/2 06:14:55: Hostname: S6 06:14:55: DHCP: SRelease placed Server ID option: 180.40.7.98 06:14:55: DHCP: SRelease: 279 bytes 06:14:55: DHCP: Releasing ipl options: 06:14:56: DHCP: SRelease attempt # 3 for entry: 06:14:56: Temp IP addr: 180.40.7.97 for peer on Interface: FastEthernet0/2 06:14:56: Temp sub net mask: 255.255.255.224 06:14:56: DHCP Lease server: 180.40.7.98, state: 7 Releasing 06:14:56: DHCP transaction id: 1E20 06:14:56: Lease: 86u all400 secs, Renewal: 43200 secs, Rebind: 75600 secs 06:14:56: Next timer fires after: 00:00:01 06:14:56: Retry count: 3 Client-ID: cisco-000a.f49a.2380-Fa0/2 06:14:56: Hostname: S6 06:14:56: DHCP: SRelease placed Server ID option: 180.40.7.98 06:14:56: DHCP: SRelease: 279 bytes 06:14:57: RAC: DHCP stopped on interface FastEthernet0/2 06:14:57: %SYS-5-CONFIG_I: Configured from console by console All possible debugging has been turned off S6# RACK11AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh run | b 0/1 interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 226.6.6.6 Prob12 duplex auto speed auto ! interface Serial1/0 no ip address encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint --More--   frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! --More--  interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ! ip access-list standard NoGroup deny 224.20.68.1 permit any --More--  ! ip access-list extended Prob12 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end --More--   R2# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#no ip access ex Prob9 R1(config)#ip access-list extended Prob12 R1(config-ext-nacl)# permit udp host 180.40.7.97 any eq tftp R1(config-ext-nacl)#! R1(config-ext-nacl)#^Z R1# *Mar 1 06:13:42.624: %SYS-5-CONFIG_I: Configured from console by console R1#^x4 % Unknown command or computer name, or unable to find computer address R1# R1# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/1 ^ % Invalid input detected at '^' marker. R4(config)#int fa 0/1 0 R4(config-if)#ip pim sp R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)#int lo 0 R4(config-if)#int lo 0p pim sparse-dense-mode R4(config-if)#^Z R4# *Mar 1 06:15:58.118: %SYS-5-CONFIG_I: Configured from console by console R4# RACK11AS>1 [Resuming connection 1 to r1 ... ] R1#^x2 % Unknown command or computer name, or unable to find computer address R1# R1# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip add      in tlo 0 ^ % Invalid input detected at '^' marker. R2(config)#in tlo 0lo 0 lo 0 tlo 0 lo 0 R2(config-if)#ip add 223.254.254.254 255.255.255.255 R2(config-if)#^x3 ^ % Invalid input detected at '^' marker. R2(config-if)# R2(config-if)# RACK11AS>3 [Resuming connection 3 to r3 ... ] * R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int lo 0 R3(config-if)#ip add 223.254.254.254 255.255.255.255.  R3(config-if)#do sh ip    run | i rp-can ip pim rp-candidate FastEthernet0/1 group-list NoGroup interval 5 bidir R3(config-if)#no ip pim rp-candidate FastEthernet0/1 group-list NoGroup inter$p-candidate FastEthernet0/1 group-list NoGroup interv al 5 bidie FastEthernet0/1 group-list NoGroup interval 5 bidir  R3(config)#$p-candidate FastEthernet0/1 group-list NoGroup interval 5 bidir group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir  group-list NoGroup interval 5 bidir l group-list NoGroup interval 5 bidiro group-list NoGroup interval 5 bidiro group-list NoGroup interval 5 bidirp group-list NoGroup interval 5 bidir0 group-list NoGroup interval 5 bidir R3(config)#no ip pim rp-candidate loop0 group-list NoGroup interval 5 bidirno ip pim rp-candidate loop0 group-list NoGroup interval 5 bidir  ip pim rp-candidate loop0 group-list NoGroup interval 5 bidir  Warning: PIMv2 not configured on Loopback0, Candidate-RP not advertised R3(config)#int lo 0 R3(config-if)#ip pim R3(config-if)#ip pim sp R3(config-if)#ip pim sparse- R3(config-if)#ip pim sparse-s  *Mar 1 06:15:19.574: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback0 (vrf default) R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-d nt lo 0  ip pim rp-candidate loop0 group-list NoGroup interval 5 bidir R3(config)#ip ms R3(config)#ip msdp ? cache-rejected-sa Store rejected SAs from all peers default-peer Default MSDP peer to accept SA messages from description Peer specific description filter-sa-request Filter SA-Requests from peer keepalive Configure keepalive parameters for a peer mesh-group Configure an MSDP mesh-group originator-id Configure MSDP Originator ID peer Configure an MSDP peer redistribute Inject multicast route entries into MSDP sa-filter Filter SA messages from peer sa-limit Configure SA limit for a peer shutdown Administratively shutdown MSDP peer timer MSDP timer ttl-threshold Configure TTL Threshold for MSDP Peer vrf Select VPN Routing/Forwarding instance R3(config)#ip msdp peer R3(config)#ip msdp peer ? Hostname or A.B.C.D Peer name or address R3(config)#ip msdp peer 180.7.  40.7.2 R3(config)# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#exit R2(config)#ip ms R2(config)#ip msdp p R2(config)#ip msdp peer 180.40.7.3 R2(config)# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 R3(config)#do ship int brie ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES manual administratively down down BRI0/0 unassigned YES manual administratively down down BRI0/0:1 unassigned YES unset administratively down down BRI0/0:2 unassigned YES unset administratively down down FastEthernet0/1 180.40.7.129 YES manual up up Serial1/0 180.40.7.33 YES manual up up Serial1/1 unassigned YES manual administratively down down Serial1/2 180.40.7.3 YES manual up up Serial1/3 unassigned YES manual administratively down down Serial1/4 unassigned YES manual administratively down down Serial1/5 unassigned YES manual administratively down down --More--  Serial1/6 unassigned YES manual administratively down down Serial1/7 unassigned YES manual administratively down down Loopback0 223.254.254.254 YES manual up up R3(config)#q^Z % Incomplete command. R3# *Mar 1 06:16:26.913: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2(config)#ip rp-ca R2(config)#ip rp-can R2(config)#ip rp-can      pim rp-ca R2(config)#ip pim rp-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config)#ip pim rp-candidate lo 0 ? bidir Group range treated in bidirectional shared-tree mode group-list group-list interval RP candidate advertisement interval priority RP candidate priority R2(config)#ip pim rp-candidate lo 0 in 5 bi Warning: PIMv2 not configured on Loopback0, Candidate-RP not advertised R2(config)#inty    t l,o  o 0 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#ip pim sparse-dense-mode nt lo 0 p pim rp-candidate lo 0 in 5 bi R2(config)# *Mar 1 06:17:37.585: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback0 (vrf default) R2(config)#^Z R2# *Mar 1 06:17:42.224: %SYS-5-CONFIG_I: Configured from console by console R2# R2# R2# R2# R2# R2#sh ip pim rp m map PIM Group-to-RP Mappings This system is a candidate RP (v2) This system is the Bootstrap Router (v2) Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 17 Uptime: 00:02:24, expires: 00:00:16 R2#sh ip msdp peer MSDP Peer 180.40.7.3 (?), AS ? Connection status: State: Up, Resets: 0, Connection source: none configured Uptime(Downtime): 00:01:41, Messages sent/received: 2/2 Output messages discarded: 0 Connection and counters cleared 00:01:41 ago SA Filtering: Input (S,G) filter: none, route-map: none Input RP filter: none, route-map: none Output (S,G) filter: none, route-map: none Output RP filter: none, route-map: none SA-Requests: Input filter: none Peer ttl threshold: 0 SAs learned from this peer: 0 Input queue size: 0, Output queue size: 0 R2# R2# R2# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#pin     shj    run int fa 0/2 Building configuration... Current configuration : 114 bytes ! interface FastEthernet0/2 no switchport ip address 180.40.7.97 255.255.255.224 ip pim sparse-dense-mode end S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#int fa 0/2 S6(config-if)#ip igmp jpo   S6(config-if)#ip igmp join-group 224.6.6.6 S6(config-if)#^Z S6# 06:22:03: %SYS-5-CONFIG_I: Configured from console by console RACK11AS>5 [Resuming connection 5 to r5 ... ] 0 S5#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0 Uptime: 00:03:41, expires: 00:03:20 S5#p 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 60 ms S5# S5# S5# S5#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 239.255.255.255), 00:04:00/00:02:07, RP 223.254.254.254, flags: BP Bidir-Upstream: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 00:03:57/00:00:00 (*, 224.2.127.254), 00:04:00/00:02:58, RP 223.254.254.254, flags: BP Bidir-Upstream: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 00:03:57/00:00:00 (*, 224.148.93.1), 00:04:20/00:01:59, RP 223.254.254.254, flags: BPL Bidir-Upstream: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 00:03:58/00:00:00 (*, 224.6.6.6), 00:00:09/00:02:56, RP 223.254.254.254, flags: BP Bidir-Upstream: FastEthernet0/1, RPF nbr 17.57.100.1 Outgoing interface list: --More--   FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 00:00:09/00:00:00 (*, 224.0.1.40), 01:04:00/00:02:59, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 01:04:00/00:00:00 S5#p 22.4  4.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S5# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip msd R3#sh ip msdp sa R3#sh ip msdp sa-cache MSDP Source-Active Cache - 0 entries R3#^x2 % Unknown command or computer name, or unable to find computer address R3# R3#^x2 % Unknown command or computer name, or unable to find computer address R3# R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.148.93.1), 00:02:26/00:03:01, RP 223.254.254.254, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:02:26/00:03:01 (*, 224.4.4.4), 00:00:42/00:02:17, RP 223.254.254.254, flags: BP Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.6.6.6), 00:01:22/00:02:49, RP 223.254.254.254, flags: BC Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:22/00:02:49 (*, 226.6.6.6), 00:02:27/00:03:01, RP 223.254.254.254, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:02:27/00:03:01 --More--   (*, 224.0.1.40), 01:04:57/00:02:45, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 01:04:57/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 01:04:57/00:00:00 Serial1/2, Forward/Sparse-Dense, 01:04:57/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 01:04:57/00:00:00 (*, 224.2.127.254), 00:02:29/00:02:58, RP 223.254.254.254, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:02:29/00:02:58 (*, 239.255.255.255), 00:02:29/00:02:58, RP 223.254.254.254, flags: B Bidir-Upstream: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:02:29/00:02:58 R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim rp-candidate lo 0 in 5 bi   R2(config)#do sh run | i ra p-can ip pim rp-candidate Loopback0 interval 5 R2(config)#^Z R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#qdo sh ip int brieip msdp peer 180.40.7.2 ip pim rp-candidate loop0 group-list NoGroup interval 5 bidir       R3(config)#do sh run | i rp-ca ip pim rp-candidate Loopback0 group-list NoGroup interval 5 R3(config)#^Z R3# RACK11AS>5 [Resuming connection 5 to r5 ... ] S5#sh ip pim m rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0 Uptime: 00:05:57, expires: 00:03:05 S5#pin sh ip pim rp mapp 224.4.4.4 sh ip mroutep 224.6.6.6  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 68 ms S5#p 224.6.6.6sh ip pim rp mapp 224.4.4.4  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 124 ms S5# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#sh ip ms R2#sh ip msdp s R2#sh ip msdp sa R2#sh ip msdp sa-cache MSDP Source-Active Cache - 0 entries R2#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.148.93.1), 00:00:58/00:03:29, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:00:58/00:03:29 (*, 224.4.4.4), 00:00:23/stopped, RP 223.254.254.254, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (17.57.100.2, 224.4.4.4), 00:00:24/00:02:35, flags: A Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: Serial1/0.1, Forward/Sparse-Dense, 00:00:24/00:03:05 (*, 226.6.6.6), 00:00:59/00:02:30, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:00:59/00:02:30 --More--   (*, 224.6.6.6), 00:01:02/stopped, RP 223.254.254.254, flags: SJC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:02/00:02:01 (17.57.100.2, 224.6.6.6), 00:00:31/00:02:28, flags: A Incoming interface: Serial1/0.2, RPF nbr 180.40.7.66 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:31/00:02:28 (*, 224.0.1.40), 01:06:39/00:02:06, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 01:06:39/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 01:06:39/00:00:00 Serial1/2, Forward/Sparse-Dense, 01:06:39/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 01:06:39/00:00:00 (*, 224.2.127.254), 00:00:29/00:03:00, RP 223.254.254.254, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0.2, Forward/Sparse-Dense, 00:00:29/00:03:00 --More-- RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#sh ip msdpsa ^ % Invalid input detected at '^' marker. R3#sh ip msdpsap sa MSDP Source-Active Cache - 2 entries (17.57.100.2, 224.4.4.4), RP 223.254.254.254, AS ?,00:00:37/00:05:50, Peer 180.40.7.2 (17.57.100.2, 224.6.6.6), RP 223.254.254.254, AS ?,00:00:41/00:05:50, Peer 180.40.7.2 R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#po    224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 60 ms Reply to request 0 from 180.40.7.97, 84 ms R4# RACK11AS>2 [Resuming connection 2 to r2 ... ]   --More--   R2#sh ip mroutesdp sa-cache MSDP Source-Active Cache - 2 entries (4.4.4.4, 224.6.6.6), RP 223.254.254.254, AS ?,00:00:09/00:05:50, Peer 180.40.7.3 (180.40.7.130, 224.6.6.6), RP 223.254.254.254, AS ?,00:00:09/00:05:50, Peer 180.40.7.3 R2#sh run | b Lo interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 226.6.6.6 Prob12 duplex auto speed auto ! interface Serial1/0 no ip address --More--   encapsulation frame-relay ! interface Serial1/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay map ip 180.40.7.33 203 broadcast frame-relay map ip 180.40.7.34 203 broadcast frame-relay interface-dlci 203 ! interface Serial1/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 201 ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode --More--   clock rate 64000 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 --More--   log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 5 ip msdp peer 180.40.7.3 ! ip access-list standard NoGroup deny 224.20.68.1 permit any ! ip access-list extended Prob12 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! --More--   R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b Lo interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim sparse-dense-mode duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.33 255.255.255.224 ip pim sparse-dense-mode --More--   encapsulation frame-relay ip ospf network point-to-multipoint ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip pim sparse-dense-mode ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! --More--  interface Serial1/6 no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim rp-candidate Loopback0 group-list NoGroup interval 5 ip pim register-rate-limit 2 ip msdp peer 180.40.7.2 ! ip access-list standard NoGroup --More--   R3#sh run |     Building configuration... Current configuration : 1802 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R3 ! boot-start-marker boot-end-marker ! ! no network-clock-participate slot 1 no network-clock-participate wic 0 no aaa new-model ip subnet-zero ! ! ! ip cef no ip domain lookup --More--  ip multicast-routing ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Loopback0 --More--   ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim sparse-dense-mode duplex auto speed auto ! interface Serial1/0 ip address 180.40.7.33 255.255.255.224 ip pim sparse-dense-mode encapsulation frame-relay --More--   ip ospf network point-to-multipoint ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ip pim sparse-dense-mode ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 --More--   no ip address shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim rp-candidate Loopback0 group-list NoGroup interval 5 ip pim register-rate-limit 2 ip msdp peer 180.40.7.2 ! ip access-list standard NoGroup deny 224.20.68.1 --More--   permit any ! ip access-list extended Prob9 permit ip any any ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! --More--  end R3# R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip mu R3(config)#no ip multicast- R3(config)#no ip multicast-routing R3(config)#no ip multicast-routing do sh run | i rp-ca  ip pim rp-candidate loop0 group-list NoGroup interval 5n ip pim rp-candidate loop0 group-list NoGroup interval 5o ip pim rp-candidate loop0 group-list NoGroup interval 5 ip pim rp-candidate loop0 group-list NoGroup interval 5 R3(config)#no in tlo 0 ^ % Invalid input detected at '^' marker. R3(config)#no in tlo 0      t lo 0 R3(config)#int fa 0/ *Mar 1 06:25:04.670: %LINK-5-CHANGED: Interface Loopback0, changed state to administratively down R3(config)#int fa 0/1 R3(config-if)#no ip pim R3(config-if)#no ip pim sp R3(config-if)#no ip pim sparse-a d R3(config-if)#no ip pim sparse-dense-mode R3(config-if)#\  *Mar 1 06:25:10.864: %PIM-5-NBRCHG: neighbor 180.40.7.130 DOWN on interface FastEthernet0/1 (vrf default) DR R3(config-if)#int s 1/2 R3(config-if)#int s 1/2no ip pim sparse-dense-mode R3(config-if)#iunt  *Mar 1 06:25:15.203: %PIM-5-NBRCHG: neighbor 180.40.7.2 DOWN on interface Serial1/2 (vrf default) non DR R3(config-if)#iun  nt s 1/0 R3(config-if)#~~int s 1/0no ip pim sparse-dense-mode R3(config-if)# *Mar 1 06:25:21.433: %PIM-5-NBRCHG: neighbor 180.40.7.35 DOWN on interface Serial1/0 (vrf default) DR R3(config-if)#do sh run | i ip pim ip pim spt-threshold 1 ip pim register-rate-limit 2 R3(config-if)#exit R3(config)#no ip msdp peer 180.40.7.2 R3(config)# *Mar 1 06:25:46.194: %MSDP-5-PEER_UPDOWN: Session to peer 180.40.7.2 going down R3(config)# R3(config)# R3(config)# R3(config)#no ip msdp peer 180.40.7.2exit do sh run | i ip pimno ip pim sparse-dense-mode do sh run | i ip pim  ip pim spt-threshold 1 ip pim register-rate-limit 2 R3(config)#no ip pim spt-threshold 1 R3(config)#no ip pim register-rate-limit 2 R3(config)#^Z R3# *Mar 1 06:26:31.159: %SYS-5-CONFIG_I: Configured from console by console R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] *M R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#i  nt l     in tu t u 0-  R4(config-if)#tun *Mar 1 06:29:21.502: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R4(config-if)#tun sou lo 0 R4(config-if)#tun dew st 2.2.2.2 R4(config-if)#keep R4(config-if)#ip address 24.24.24.4 255.255.255.90  0 R4(config-if)#ip pim R4(config-if)#ip pim sp R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)#^Z R4# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#in  t lo 1 R2(config-if)#ip add 2;.2.    .2.2.2 255.255.255.0 R2(config-if)#int tu 0 R2(config-if)#tun sou *Mar 1 06:28:37.070: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R2(config-if)#tun sou lo 1 R2(config-if)#tun dest 4.4.4.4.  R2(config-if)#keep R2(config-if)# *Mar 1 06:28:46.653: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R2(config-if)#ip add 24.24.24.2 255.255.255.0 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#^Z R2# *Mar 1 06:28:58.958: %SYS-5-CONFIG_I: Configured from console by console R2#p 24.24.24. *Mar 1 06:29:02.860: %PIM-5-NBRCHG: neighbor 24.24.24.4 UP on interface Tunnel0 (vrf default) R2#p 24.24.24.4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 24.24.24.4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 36/46/76 ms R2# *Mar 1 06:29:05.092: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.11 on Tunnel0 from LOADING to FULL, Loading Done R2# R2# R2# R2# R2#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 56 ms R2# RACK11AS>67~ % Unknown command or computer name, or unable to find computer address RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:38, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:38, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:38, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:38, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:39, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:39, FastEthernet0/0 R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip mrout R4(config)#ip mroute 0.0.0.0 0.0.0.0 tu 0 R4(config)# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4(config)#^Z R4#sh ip *Mar 1 06:33:09.910: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip pim m rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:03, expires: 00:03:25 R4# R4# R4# R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 40 ms S6# S6# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | b Lo interface Loopback0 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface Loopback1 ip address 2.2.2.2 255.255.255.0 ! interface Tunnel0 ip address 24.24.24.2 255.255.255.0 ip pim sparse-dense-mode keepalive 10 3 tunnel source Loopback1 tunnel destination 4.4.4.4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface BRI0/0 no ip address shutdown --More--   R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b Lo interface Loopback0 ip address 4.4.4.4 255.255.255.0 ip pim sparse-dense-mode ip igmp join-group 224.4.4.4 ! interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode keepalive 10 3 tunnel source Loopback0 tunnel destination 2.2.2.2 ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 8 ip pim sparse-dense-mode duplex auto speed auto ! interface ATM1/0 ip address 192.10.32.11 255.255.255.0 ip nat outside --More--   no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 broadcast ! ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip nat inside source list IPNAT interface ATM1/0 overload no ip http server no ip http secure-server ip classless ! ip pim bidir-enable ip pim spt-threshold 1 ip mroute 0.0.0.0 0.0.0.0 Tunnel0 ! ! ip access-list standard IPNAT permit 180.40.7.0 0.0.0.255 permit 17.0.0.0 0.255.255.255 ! --More--   R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int     ip mroute 0.0.0.0 0.0.0.0 tu 0nip mroute 0.0.0.0 0.0.0.0 tu 0oip mroute 0.0.0.0 0.0.0.0 tu 0 ip mroute 0.0.0.0 0.0.0.0 tu 0 R4(config)#inty    tu 0 R4(config-if)#do sh ip ospf int tu 0 Tunnel0 is up, line protocol is up Internet Address 24.24.24.4/24, Area 0 Process ID 1, Router ID 192.10.32.11, Network Type POINT_TO_POINT, Cost: 11111 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 Hello due in 00:00:05 Index 4/4, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 180.40.7.98 Suppress hello for 0 neighbor(s) R4(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:04:09, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:04:09, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:04:09, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:04:09, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:04:12, FastEthernet0/0 O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:04:12, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:04:12, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:04:12, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:04:12, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:04:12, FastEthernet0/0 R4(config-if)#ip ospf co 1 R4(config-if)# *Mar 1 06:36:10.498: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 06:36:11.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 06:36:11.498: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 06:36:11.502: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#ip ospf co 1nip ospf co 1oip ospf co 1 ip ospf co 1 R4(config-if)# *Mar 1 06:37:21.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 06:37:21.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4(config-if)# *Mar 1 06:37:23.962: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config-if)#exit R4(config)#ip access-list ex    st NoLoop R4(config-std-nacl)#den 2.2.2.2 R4(config-std-nacl)#per any R4(config-std-nacl)#exit R4(config)#router ospf 1 R4(config-router)#distr R4(config-router)#distribute-list NoP Loop in tun 0 R4(config-router)#int tu 1 90  0 R4(config-if)#ip so  ospf cost 1 R4(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 24.24.24.2, 00:00:06, Tunnel0 O 17.100.1.0 [110/792] via 24.24.24.2, 00:00:06, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 24.24.24.2, 00:00:06, Tunnel0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:07, FastEthernet0/0 --More--   [110/782] via 24.24.24.2, 00:00:07, Tunnel0 O 180.40.7.35/32 [110/1] via 24.24.24.2, 00:00:13, Tunnel0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:13, FastEthernet0/0 O 180.40.7.66/32 [110/782] via 24.24.24.2, 00:00:13, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:13, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:13, Tunnel0 R4(config-if)# *Mar 1 06:40:31.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 06:40:31.498: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 06:40:31.502: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:01, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:01, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:01, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:01, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets O 24.24.24.0 [110/11893] via 180.40.7.129, 00:00:02, FastEthernet0/0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:05, FastEthernet0/0 R4(config-if)# *Mar 1 06:40:41.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 06:40:41.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4(config-if)# *Mar 1 06:40:43.974: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:00, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:00, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:00, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:00, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:02, FastEthernet0/0 R4(config-if)#do sh ip routeip ospf cost 1do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:06, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:06, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/783] via 180.40.7.129, 00:00:06, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:06, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--   R4(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 24.24.24.2, 00:00:00, Tunnel0 O 17.100.1.0 [110/792] via 24.24.24.2, 00:00:00, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 24.24.24.2, 00:00:00, Tunnel0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:01, FastEthernet0/0 --More--   [110/782] via 24.24.24.2, 00:00:01, Tunnel0 O 180.40.7.35/32 [110/1] via 24.24.24.2, 00:00:03, Tunnel0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:03, FastEthernet0/0 O 180.40.7.66/32 [110/782] via 24.24.24.2, 00:00:03, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:03, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:03, Tunnel0 R4(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 24.24.24.2, 00:00:04, Tunnel0 O 17.100.1.0 [110/792] via 24.24.24.2, 00:00:04, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 24.24.24.2, 00:00:04, Tunnel0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:06, FastEthernet0/0 --More--   [110/782] via 24.24.24.2, 00:00:06, Tunnel0 O 180.40.7.35/32 [110/1] via 24.24.24.2, 00:00:06, Tunnel0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:06, FastEthernet0/0 O 180.40.7.66/32 [110/782] via 24.24.24.2, 00:00:06, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:06, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:06, Tunnel0 R4(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/792] via 24.24.24.2, 00:00:09, Tunnel0 O 17.100.1.0 [110/792] via 24.24.24.2, 00:00:09, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 24.24.24.2, 00:00:09, Tunnel0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:10, FastEthernet0/0 --More--   [110/782] via 24.24.24.2, 00:00:10, Tunnel0 O 180.40.7.35/32 [110/1] via 24.24.24.2, 00:00:10, Tunnel0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:10, FastEthernet0/0 O 180.40.7.66/32 [110/782] via 24.24.24.2, 00:00:10, Tunnel0 O 180.40.7.65/32 [110/1] via 24.24.24.2, 00:00:10, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:10, Tunnel0 R4(config-if)#do sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets O 24.24.24.0 [110/1] via 24.24.24.4, 00:00:01, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 3 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:15, FastEthernet0/0 O 180.40.7.33/32 [110/1] *Mar 1 06:41:11.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 06:41:11.498: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 06:41:11.502: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detachedvia 180.40.7.129, 00:00:15, FastEthernet0/0 R4(config-if)# *Mar 1 06:41:21.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 06:41:21.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4(config-if)# *Mar 1 06:41:23.974: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config-if)#  dh run       o sh run | ospf sh run | ospf ^ % Invalid input detected at '^' marker. R4(config-if)#do sh run | ospf\ \     b router router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 distribute-list NoLoop in Tunnel0 ! ip nat inside source list IPNAT interface ATM1/0 overload no ip http server no ip http secure-server ip classless ! ip pim bidir-enable ip pim spt-threshold 1 ! ! ip access-list standard IPNAT permit 180.40.7.0 0.0.0.255 permit 17.0.0.0 0.255.255.255 ip access-list standard NoLoop deny 2.2.2.2 permit any ! ! ! --More--   R4(config-if)# R4(config-if)# *Mar 1 06:41:51.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 06:41:51.498: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 (vrf default) non DR *Mar 1 06:41:51.502: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)#router o        do sh run | b routerospf ip route ip ospf cost 1nip ospf cost 1oip ospf cost 1 ip ospf cost 1 R4(config-if)#router bgp     *Mar 1 06:42:01.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 06:42:01.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4(config-if)#router b po   *Mar 1 06:42:03.978: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config-if)#router ospf 1 R4(config-router)#no dire  str R4(config-router)#no distribute-list NoLoop in tun 0 R4(config-router)#router eigrp 100 R4(config-router)#no autpo  ^ % Invalid input detected at '^' marker. R4(config-router)#no autp  to R4(config-router)#net 4.4.4.4 0.0.0.0 R4(config-router)#net 180.40.7.130 0.0.0.0 R4(config-router)# RACK11AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router eigrp 100 R3(config-router)#no auto R3(config-router)#net 180.40.7.129 0.0.0.0 R3(config-router)#net 180.40.7.129 0.0.0.0 0.0.0.0  0.0.0.0  *Mar 1 06:41:03.341: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.130 (FastEthernet0/1) is up: new adjacency R3(config-router)#net 180.40.7.1 0.0.0.0 0.0.0.0 3 0.0.0.0 R3(config-router)# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#sh    cio o  onfi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router eigrp 100 R2(config-router)#net 2.2.2.2 0.0.0.0 R2(config-router)#net 180.40.7.2 0.0.0.0 R2(config-router)# *Mar 1 06:41:31.595: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.3 (Serial1/2) is up: new adjacency R2(config-router)#int lo 1 R2(config-if)#ip ospf net po R2(config-if)#ip ospf net point-to-p R2(config-if)#ip ospf net point-to-point R2(config-if)# RACK11AS>4 [Resuming connection 4 to r4 ... ] * R4(config-router)#int tu 09  R4(config-if)#int tu 0net 180.40.7.130 0.0.0.04.4.4.4 0.0.0.0 o auto prouter eigrp 100no distribute-list NoLoop in tun 0router ospf 1 no ip ospf cost 1 R4(config-if)#no ip ospf cost 1no\ ip ospf cost 1 ip ospf cost 1  ip ospf cost 1  ip ospf cost 1  R4(config-if)#^Z R4#sh ip *Mar 1 06:44:35.918: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:20, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:20, FastEthernet0/0 2.0.0.0/8 is variably subnetted, 2 subnets, 2 masks O 2.2.2.0/24 [110/783] via 180.40.7.129, 00:00:20, FastEthernet0/0 D 2.0.0.0/8 [90/20642560] via 180.40.7.129, 00:00:47, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:20, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 --More-- RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(config-if)#router bgp     eirgp 100 ^ % Invalid input detected at '^' marker. R2(config)#router eirgp 100       grp 100 R2(config-router)#no auyt  to R2(config-router)#^Z R2# RACK11AS>4 [Resuming connection 4 to r4 ... ] *Ma  180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--   R4#[Ash ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:08, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:08, FastEthernet0/0 2.0.0.0/24 is subnetted, 1 subnets O 2.2.2.0 [110/783] via 180.40.7.129, 00:00:08, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:08, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets O 24.24.24.0 [110/11893] via 180.40.7.129, 00:00:09, FastEthernet0/0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:01:41, FastEthernet0/0 O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:12, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:12, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:12, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:12, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:12, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:15, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:15, FastEthernet0/0 2.0.0.0/24 is subnetted, 1 subnets D 2.2.2.0 [90/20642560] via 180.40.7.129, 00:00:06, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:15, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets O 24.24.24.0 [110/11893] via 180.40.7.129, 00:00:16, FastEthernet0/0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--   R4#sh ip route ei 2.0.0.0/24 is subnetted, 1 subnets D 2.2.2.0 [90/20642560] via 180.40.7.129, 00:00:16, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:01:54, FastEthernet0/0 R4#sh ip route ei  opf Translating "opf" ^ % Invalid input detected at '^' marker. R4#sh ip route opfspf 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:10, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:10, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:10, FastEthernet0/0 24.0.0.0/24 is subnetted, 1 subnets O 24.24.24.0 [110/11893] via 180.40.7.129, 00:00:10, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:10, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:10, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:10, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:10, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:10, FastEthernet0/0 R4#sh ip route ospf sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES manual up up ATM1/0 192.10.32.11 YES manual up up Loopback0 4.4.4.4 YES manual up up Tunnel0 24.24.24.4 YES manual up down R4# R4# R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES manual up up ATM1/0 192.10.32.11 YES manual up up Loopback0 4.4.4.4 YES manual up up Tunnel0 24.24.24.4 YES manual up down R4#sh i  *Mar 1 06:46:01.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 06:46:01.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4#sh *Mar 1 06:46:04.066: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4#sh ip int brieroute ospf 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:01, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:01, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:01, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:01, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:01, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:01, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:01, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:01, FastEthernet0/0 R4#sh ip route ospf 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:05, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:05, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:05, FastEthernet0/0 R4#sh ip route ospf 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/1573] via 180.40.7.129, 00:00:07, FastEthernet0/0 O 17.100.1.0 [110/1573] via 180.40.7.129, 00:00:07, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/783] via 180.40.7.129, 00:00:07, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks O 180.40.7.35/32 [110/782] via 180.40.7.129, 00:00:07, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:07, FastEthernet0/0 O 180.40.7.66/32 [110/1563] via 180.40.7.129, 00:00:07, FastEthernet0/0 O 180.40.7.65/32 [110/782] via 180.40.7.129, 00:00:07, FastEthernet0/0 O 180.40.7.96/27 [110/783] via 180.40.7.129, 00:00:07, FastEthernet0/0 R4#sh ip route ospfint brie route ospfpf ei  2.0.0.0/24 is subnetted, 1 subnets D 2.2.2.0 [90/20642560] via 180.40.7.129, 00:01:11, FastEthernet0/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks D 180.40.7.0/27 [90/20514560] via 180.40.7.129, 00:02:50, FastEthernet0/0 R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 44 ms S6# RACK11AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh run | b router router eigrp 100 network 2.2.2.2 0.0.0.0 network 180.40.7.2 0.0.0.0 no auto-summary ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 5 ip msdp peer 180.40.7.3 ! ip access-list standard NoGroup deny 224.20.68.1 permit any ! --More--   R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] * R3(config-router)#^Z R3#sh run *Mar 1 06:45:14.441: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b i eigrp router eigrp 100 network 180.40.7.3 0.0.0.0 network 180.40.7.129 0.0.0.0 no auto-summary ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! ip access-list standard NoGroup deny 224.20.68.1 permit any ! ip access-list extended Prob9 permit ip any any ! ! ! --More--   R3# RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b Tu interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode ip ospf cost 1 keepalive 10 3 tunnel source Loopback0 tunnel destination 2.2.2.2 ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 8 ip pim sparse-dense-mode duplex auto speed auto ! interface ATM1/0 ip address 192.10.32.11 255.255.255.0 ip nat outside no atm ilmi-keepalive pvc 0/72 protocol ip 192.10.32.254 broadcast ! --More--  ! router eigrp 100 network 4.4.4.4 0.0.0.0 network 180.40.7.130 0.0.0.0 no auto-summary ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ip nat inside source list IPNAT interface ATM1/0 overload no ip http server no ip http secure-server ip classless ! ip pim bidir-enable ip pim spt-threshold 1 ! ! ip access-list standard IPNAT permit 180.40.7.0 0.0.0.255 permit 17.0.0.0 0.255.255.255 ip access-list standard NoLoop --More--   R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#no router eigrp 100 RACK11AS>3 [Resuming connection 3 to r3 ... ] *M R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no router eigrp 100 RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar R2#confit  t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#no router eigrp 100 RACK11AS>4 [Resuming connection 4 to r4 ... ] *Mar 1 R4(config)#int tu 0 R4(config-if)#no ip ospf cost 1 R4(config-if)# *Mar 1 06:49:51.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 06:49:51.526: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4(config-if)# *Mar 1 06:49:54.086: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config-if)#ex ~  router ospf 1 R4(config-router)#net 4.4.4.4 0.0.0.0 area 51 R4(config-router)# *Mar 1 06:50:13.926: %OSPF-6-AREACHG: 4.4.4.4/32 changed from area 0 to area 51 R4(config-router)#net 180.40.7.130 0.0.0.0 area 51 R4(config-router)# *Mar 1 06:50:24.722: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 06:50:24.726: %OSPF-6-AREACHG: 180.40.7.130/32 changed from area 0 to area 51 R4(config-router)#Z *Mar 1 06:50:25.262: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.129, FastEthernet0/0 R4(config-router)#Z\  ^Z R4# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Mar R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router ospf 1 R3(config-router)#net 180.40.7.129 0.0.0.0 area 51 R3(config-router)#net 180.40.7.129 0.0.0.0 area 51 *Mar 1 06:48:21.415: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.11 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached R3(config-router)#net 180.40.7.129 0.0.0.0 area 51 *Mar 1 06:48:21.419: %OSPF-6-AREACHG: 180.40.7.129/32 changed from area 0 to area 51 R3(config-router)#net 180.40.7.129 0.0.0.0 area 51 0.0.0.0 area 51  0.0.0.0 area 51  0.0.0.0 area 51 3 0.0.0.0 area 51 R3(config-router)#^Z R3# *Mar 1 06:48:25.963: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 06:48:25.967: %OSPF-6-AREACHG: 180.40.7.3/32 changed from area 0 to area 51 *Mar 1 06:48:26.472: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.2, Serial1/2 R3# RACK11AS>2 [Resuming connection 2 to r2 ... ] R2(c R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#router ospf 1 R2(config-router)#net 2.2.2.2 0.0.0.0 area 51 R2(config-router)#ne *Mar 1 06:48:39.882: %OSPF-6-AREACHG: 2.2.2.2/32 changed from area 0 to area 51t R2(config-router)#net 180.40.7.2 0.0.0.0 area 41  51 R2(config-router)# *Mar 1 06:48:48.247: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 06:48:48.247: %OSPF-6-AREACHG: 180.40.7.2/32 changed from area 0 to area 51 R2(config-router)#^Z R2# *Mar 1 06:48:48.848: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial1/2 from LOADING to FULL, Loading Done *Mar 1 06:48:49.129: %SYS-5-CONFIG_I: Configured from console by console R2# RACK11AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.98 0 FULL/ - 00:01:55 180.40.7.35 Serial1/0 180.40.7.98 0 FULL/ - 00:00:38 180.40.7.2 Serial1/2 192.10.32.11 1 2WAY/DROTHER 00:00:36 180.40.7.130 FastEthernet0/1 R3# *Mar 1 06:49:03.392: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.11 on FastEthernet0/1 from LOADING to FULL, Loading Done R3# R3# R3# R3#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.98 0 FULL/ - 00:01:52 180.40.7.35 Serial1/0 180.40.7.98 0 FULL/ - 00:00:39 180.40.7.2 Serial1/2 192.10.32.11 1 FULL/DR 00:00:39 180.40.7.130 FastEthernet0/1 R3# RACK11AS>r4 Translating "r4" Trying R4 (1.1.1.1, 2004)... Open ************************************************************** Global Knowledge Hands-On Labs Access Server Access is restricted to Global Knowledge CCIE Students ************************************************************** Please re-enter your password. (This is the same password you used to log onto the Lab website.) If you see a username prompt, please wait 40 seconds and try again. If the username prompt persists, please reset equipment from your "Pod x" link. This console appears to be occupied. Use the 'Clear Line' option on the browser to release it. Then try again. [Connection to r4 closed by foreign host] RACK11AS>4 [Resuming connection 4 to r4 ... ] *Ma R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.129 1 FULL/BDR 00:00:33 180.40.7.129 FastEthernet0/0 R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES manual up up ATM1/0 192.10.32.11 YES manual up up Loopback0 4.4.4.4 YES manual up up Tunnel0 24.24.24.4 YES manual up down R4# R4# R4# R4# *Mar 1 06:51:51.498: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R4# R4# R4# R4#sh ip int brieospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.98 0 INIT/ - 00:00:38 24.24.24.2 Tunnel0 180.40.7.129 1 FULL/BDR 00:00:35 180.40.7.129 FastEthernet0/0 R4# *Mar 1 06:51:55.806: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 (vrf default) R4# *Mar 1 06:52:01.778: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4# R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.98 0 FULL/ - 00:00:39 24.24.24.2 Tunnel0 180.40.7.129 1 FULL/BDR 00:00:37 180.40.7.129 FastEthernet0/0 R4#sh uip route ^ % Invalid input detected at '^' marker. R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 2.0.0.0/24 is subnetted, 1 subnets O 2.2.2.0 [110/783] via 180.40.7.129, 00:00:29, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 O 180.40.7.0 [110/782] via 180.40.7.129, 00:00:29, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 2.0.0.0/24 is subnetted, 1 subnets O 2.2.2.0 [110/783] via 180.40.7.129, 00:00:32, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/27 is subnetted, 2 subnets C 180.40.7.128 is directly connected, FastEthernet0/0 O 180.40.7.0 [110/782] via 180.40.7.129, 00:00:32, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/11902] via 24.24.24.2, 00:00:06, Tunnel0 O 17.100.1.0 [110/11902] via 24.24.24.2, 00:00:06, Tunnel0 2.0.0.0/24 is subnetted, 1 subnets O 2.2.2.0 [110/783] via 180.40.7.129, 00:00:43, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/11112] via 24.24.24.2, 00:00:06, Tunnel0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 C 192.10.32.0/24 is directly connected, ATM1/0 180.40.0.0/16 is variably subnetted, 7 subnets, 2 masks --More--  C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/782] via 180.40.7.129, 00:00:44, FastEthernet0/0 O 180.40.7.35/32 [110/11111] via 24.24.24.2, 00:00:07, Tunnel0 O 180.40.7.33/32 [110/11892] via 24.24.24.2, 00:00:07, Tunnel0 O 180.40.7.66/32 [110/11892] via 24.24.24.2, 00:00:07, Tunnel0 O 180.40.7.65/32 [110/11111] via 24.24.24.2, 00:00:07, Tunnel0 O 180.40.7.96/27 [110/11112] via 24.24.24.2, 00:00:07, Tunnel0 R4# RACK11AS>6 [Resuming connection 6 to r6 ... ] S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 40 ms S6# RACK11AS>2 [Resuming connection 2 to r2 ... ] *Mar 1 R2#sh run | b router router ospf 1 log-adjacency-changes network 2.2.2.2 0.0.0.0 area 51 network 180.40.7.2 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback0 interval 5 ip msdp peer 180.40.7.3 ! ip access-list standard NoGroup deny 224.20.68.1 permit any ! ip access-list extended Prob12 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! --More--   R2# RACK11AS>s 3 [Resuming connection 3 to r3 ... ] R3#sh rnu | ospf ^ % Invalid input detected at '^' marker. R3#sh rnu | ospfbospf ospf ^ % Invalid input detected at '^' marker. R3#sh run | b ospf ip ospf network point-to-multipoint ! interface Serial1/1 no ip address shutdown ! interface Serial1/2 ip address 180.40.7.3 255.255.255.224 ! interface Serial1/3 no ip address shutdown ! interface Serial1/4 no ip address shutdown ! interface Serial1/5 no ip address shutdown ! interface Serial1/6 no ip address --More--   shutdown ! interface Serial1/7 no ip address shutdown ! router ospf 1 log-adjacency-changes network 180.40.7.3 0.0.0.0 area 51 network 180.40.7.129 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ip classless ! no ip http server no ip http secure-server ! ip access-list standard NoGroup deny 224.20.68.1 permit any ! ip access-list extended Prob9 permit ip any any --More-- RACK11AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b router router ospf 1 log-adjacency-changes network 4.4.4.4 0.0.0.0 area 51 network 180.40.7.130 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ip nat inside source list IPNAT interface ATM1/0 overload no ip http server no ip http secure-server ip classless ! ip pim bidir-enable ip pim spt-threshold 1 ! ! ip access-list standard IPNAT permit 180.40.7.0 0.0.0.255 permit 17.0.0.0 0.255.255.255 ip access-list standard NoLoop deny 2.2.2.2 permit any ! ! --More--