=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2007.01.22 19:18:48 =~=~=~=~=~=~=~=~=~=~=~= coni t ^ % Invalid input detected at '^' marker. R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip mu R4(config)#ip multicast- R4(config)#ip multicast-routing R4(config)#int fa 0/0 R4(config-if)#ip pim R4(config-if)#ip pim dw  R4(config-if)#ip pim de R4(config-if)#ip pim dense-mode R4(config-if)#ip igmp jp *Mar 1 00:11:14.459: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.130 on interface FastEthernet0/0 (vrf default) R4(config-if)#ip igmp jp R4(config-if)#ip igmp jp  R4(config-if)#ip igmp join-group 224, .4.4.4 R4(config-if)#^Z R4# *Mar 1 00:11:23.227: %SYS-5-CONFIG_I: Configured from console by console R4# RACK15AS>1 [Resuming connection 1 to r1 ... ] R1# R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int   ip mu R1(config)#ip multicast- R1(config)#ip multicast-routing R1(config)#int e 0/0 R1(config-if)#io  ip pim R1(config-if)#ip pim sp R1(config-if)#ip pim sparse-d R1(config-if)#ip pim sparse-dense-mode R1(config-if)#ip pim sparse-dense-mode *Mar 1 00:10:36.787: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.57.100.1 on interface Ethernet0/0 (vrf default) R1(config-if)#ip pim sparse-dense-mode nt e 0/0  1 R1(config-if)#int e 0/1p pim sparse-dense-mode R1(config-if)#int s 0/0.1 R1(config-subif)# *Mar 1 00:10:43.826: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.100.1.1 on interface Ethernet0/1 (vrf default) R1(config-subif)#int s 0/0.1p pim sparse-dense-mode R1(config-subif)#ip pim sparse-dense-mode nt s 0/0.1  2 R1(config-subif)#int s 0/0.2p pim sparse-dense-mode R1(config-subif)#ip pim sparse-dense-mode nt s 0/0.2  1 R1(config-subif)#no shut R1(config-subif)#do sh ip int brie Interface IP-Address OK? Method Status Protocol Ethernet0/0 17.57.100.1 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 180.40.7.34 YES manual up up Serial0/0.2 180.40.7.66 YES manual up up Ethernet0/1 17.100.1.1 YES manual up up Serial0/1 unassigned YES manual administratively down down R1(config-subif)#^Z R1# RACK15AS>2 [Resuming connection 2 to r2 ... ] R2#coni fi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip mu R2(config)#ip multicast- R2(config)#ip multicast-routing R2(config)#int f a0/1 ^ % Invalid input detected at '^' marker. R2(config)#int f a0/1a0/1  R2(config-if)#ip pi R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#int s 1/ *Mar 1 00:10:55.044: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.98 on interface FastEthernet0/1 (vrf default) R2(config-if)#int s 1/0.1 R2(config-subif)#int s 1/0.1p pim sparse-dense-mode R2(config-subif)#ip pim sparse-dense-mode nt s 1/0.1  2 R2(config-subif)#int s 1/0.2p pim sparse-dense-mode *Mar 1 00:10:58.955: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.35 on interface Serial1/0.1 (vrf default) R2(config-subif)#ip pim sparse-dense-mode R2(config-subif)#ip pim sparse-dense-mode nt s 1/0.2     *Mar 1 00:11:00.766: %PIM-5-NBRCHG: neighbor 180.40.7.66 UP on interface Serial1/0.2 (vrf default) *Mar 1 00:11:00.766: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.66 on interface Serial1/0.2 (vrf default) R2(config-subif)#int s 1/2 R2(config-if)#int s 1/2p pim sparse-dense-mode R2(config-if)# R2(config-if)# R2(config-if)# R2(config-if)#^Z R2# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip mu R3(config)#ip multicast- R3(config)#ip multicast-routing R3(config)#int fa 0/1 R3(config-if)#ip pi R3(config-if)#ip pim sp R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)#ip pim sparse-dense-mode nt fa 0/1 p pim sparse-dense-mode   *Mar 1 00:11:22.882: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.129 on interface FastEthernet0/1 (vrf default) R3(config-if)#int s 1/0 R3(config-if)#int s 1/0p pim sparse-dense-mode R3(config-if)#ip pim sparse-dense-mode nt s 1/0  2 R3(config-if)# *Mar 1 00:11:29.176: %PIM-5-NBRCHG: neighbor 180.40.7.35 UP on interface Serial1/0 (vrf default) *Mar 1 00:11:29.180: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.35 on interface Serial1/0 (vrf default) *Mar 1 00:11:29.240: %PIM-5-NBRCHG: neighbor 180.40.7.34 UP on interface Serial1/0 (vrf default) R3(config-if)#int s 1/2p pim sparse-dense-mode R3(config-if)#^Z R3# *Mar 1 00:11:31.548: %PIM-5-NBRCHG: neighbor 180.40.7.2 UP on interface Serial1/2 (vrf default) R3# *Mar 1 00:11:32.554: %SYS-5-CONFIG_I: Configured from console by console R3# *Mar 1 00:11:50.131: %PIM-5-NBRCHG: neighbor 180.40.7.130 UP on interface FastEthernet0/1 (vrf default) *Mar 1 00:11:50.131: %PIM-5-DRCHG: DR change from neighbor 180.40.7.129 to 180.40.7.130 on interface FastEthernet0/1 (vrf default) R3# RACK15AS>5 [Resuming connection 5 to r5 ... ] S5#conf t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip mu S5(config)#ip multicast- S5(config)#ip multicast-routing S5(config)#int fa 0/2 S5(config-if)#int fa 0/2 1 S5(config-if)#ip pim S5(config-if)#ip pim sp S5(config-if)#ip pim sparse-d S5(config-if)#ip pim sparse-dense-mode S5(config-if)#^Z S5# RACK15AS>6 [Resuming connection 6 to r6 ... ] S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip mu S6(config)#ip multicast- S6(config)#ip multicast-routing S6(config)#int fa 0/2 S6(config-if)#ip pim sp S6(config-if)#ip pim sparse-d S6(config-if)#ip pim sparse-dense-mode S6(config-if)#^Z S6# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#conf y ^ % Invalid input detected at '^' marker. R7# R7#conf y confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip mu R7(config)#ip multicast- R7(config)#ip multicast-routing R7(config)#int fa 0/1 R7(config-if)#ip p pi R7(config-if)#ip pim sp R7(config-if)#ip pim sparse-d R7(config-if)# R7(config-if)#^Z R7# *Mar 1 00:14:00.476: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 00:14:01.310: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 17.100.1.2 on interface FastEthernet0/1 (vrf default) R7#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:00:08/00:02:54, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:00:08/00:00:00 R7# RACK15AS>1 [Resuming connection 1 to r1 ... ] *Mar 1 00:11:46.874: %SYS R1#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:05:04/00:02:42, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Ethernet0/1, Forward/Sparse-Dense, 00:00:25/00:00:00 Serial0/0.1, Forward/Sparse-Dense, 00:02:58/00:00:00 Serial0/0.2, Forward/Sparse-Dense, 00:03:29/00:00:00 Ethernet0/0, Forward/Sparse-Dense, 00:05:04/00:00:00 R1# RACK15AS>7 [Resuming connection 7 to r7 ... ] * R7#pi 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 112 ms Reply to request 0 from 180.40.7.130, 144 ms Reply to request 0 from 180.40.7.130, 132 ms R7# RACK15AS>5 [Resuming connection 5 to r5 ... ] 00:1 S5#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 104 ms Reply to request 0 from 180.40.7.130, 136 ms Reply to request 0 from 180.40.7.130, 124 ms S5# RACK15AS>6 [Resuming connection 6 to r6 ... ] 0 S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 60 ms Reply to request 0 from 180.40.7.130, 108 ms Reply to request 0 from 180.40.7.130, 88 ms S6#coi nfi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#int fa 0/2 S6(config-if)#ip igmp jo S6(config-if)#ip igmp join-group 224.6.6.6.6   S6(config-if)#ip igmp join-group 224.6.6.6 S6(config-if)#^Z S6# RACK15AS>4 [Resuming connection 4 to r4 ... ] *M R4#poi 224.6.6.6 ^ % Invalid input detected at '^' marker. R4#poi 224.6.6.6i 224.6.6.6 \i 224.6.6.6 ^ % Invalid input detected at '^' marker. R4#p\i 224.6.6.6 p\i 224.6.6.6 p 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 80 ms R4# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#sjh  h ip mrotue ^ % Invalid input detected at '^' marker. R3#sh ip mrotue   ute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:05:42/stopped, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:05:32/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:05:34/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:05:42/00:00:00 (17.57.100.2, 224.4.4.4), 00:01:44/00:01:22, flags: T Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:45/00:00:00 Serial1/2, Prune/Sparse-Dense, 00:01:45/00:01:17 (17.100.1.2, 224.4.4.4), 00:02:25/00:00:41, flags: T Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:02:25/00:00:00 Serial1/2, Prune/Sparse-Dense, 00:02:25/00:00:37 --More--   (180.40.7.97, 224.4.4.4), 00:01:47/00:01:17, flags: T Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:01:47/00:00:00 Serial1/2, Prune/Sparse-Dense, 00:01:47/00:01:12 (*, 224.6.6.6), 00:00:28/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:00:28/00:00:00 Serial1/0, Forward/Sparse-Dense, 00:00:28/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:00:28/00:00:00 (180.40.7.130, 224.6.6.6), 00:00:28/00:02:39, flags: T Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:28/00:00:00, A Serial1/2, Prune/Sparse-Dense, 00:00:28/00:02:35, A (*, 224.0.1.40), 00:05:54/00:02:48, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: --More--   R3# RACK15AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b ip m ip multicast-routing ip cef ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode half-duplex ! interface Serial0/0 --More--   no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 102 ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim sparse-dense-mode half-duplex no keepalive ! interface Serial0/1 no ip address --More-- RACK15AS>4 [Resuming connection 4 to r4 ... ] R4#sh run | b ip m ip multicast-routing ip audit po max-events 100 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim dense-mode --More--   ip igmp join-group 224.4.4.4 --More--   duplex auto --More--   speed auto --More--  ! --More--  interface ATM1/0 --More--   ip address 192.10.32.15 255.255.255.0 --More--   ip nat outside --More--   no atm ilmi-keepalive --More--   R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#ip pim st R4(config-if)#ip pim state-refresh ? origination-interval PIM State-Refresh origination interval R4(config-if)#ip pim state-refresh o R4(config-if)#ip pim state-refresh origination-interval ? <1-100> Interval in seconds R4(config-if)#ip pim state-refresh origination-interval 8 R4(config-if)#^Z R4# R4# R4# R4# R4# *Mar 1 00:22:36.971: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip pim int Address Interface Ver/ Nbr Query DR DR Mode Count Intvl Prior 180.40.7.130 FastEthernet0/0 v2/D 1 30 1 180.40.7.130 R4#sh ip pim int fa 0/0 Address Interface Ver/ Nbr Query DR DR Mode Count Intvl Prior 180.40.7.130 FastEthernet0/0 v2/D 1 30 1 180.40.7.130 R4#sh ip pim int fa 0/0      ? ATM ATM interface Async Async interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing count Interface multicast packet count detail PIM detailed information df BIDIR PIM Designated Forwarder tag Interface specific multicast tag information | Output modifiers R4#sh ip pim int de R4#sh ip pim int detail FastEthernet0/0 is up, line protocol is up Internet address is 180.40.7.130/27 Multicast switching: fast Multicast packets in/out: 9/0 Multicast boundary: not set Multicast TTL threshold: 0 PIM: enabled PIM version: 2, mode: dense PIM DR: 180.40.7.130 (this system) PIM neighbor count: 1 PIM Hello/Query interval: 30 seconds PIM State-Refresh processing: enabled PIM State-Refresh origination: enabled, interval: 8 seconds PIM NBMA mode: disabled PIM ATM multipoint signalling: disabled PIM domain border: disabled Multicast Tagswitching: disabled R4#deb ip pim PIM debugging is on R4# R4# R4# R4# RACK15AS>6 [Resuming connection 6 to r6 ... ] 00 S6#pin 224.5.5.5 re S6#pin 224.5.5.5 repeat 1000000 Type escape sequence to abort. Sending 1000000, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: . RACK15AS>4 [Resuming connection 4 to r4 ... ] *M R4#sh ip mrotue ^ % Invalid input detected at '^' marker. R4#sh ip mrotueue ute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:12:21/00:02:46, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:12:21/00:00:00 (*, 224.5.5.5), 00:00:12/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:00:12/00:00:00 (180.40.7.97, 224.5.5.5), 00:00:13/00:02:45, flags: PT Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.0.1.40), 00:12:30/00:02:38, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:12:30/00:00:00 --More--   R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 24 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: disabled, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 24 message lines logged R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#logg buf R4(config)#logg buf   cpon   on R4(config)#^Z R4# *Mar 1 00:24:09.363: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4# R4#confi tsh log ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:13:01/00:02:06, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:13:01/00:00:00 (*, 224.5.5.5), 00:00:52/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:00:52/00:00:00 (180.40.7.97, 224.5.5.5), 00:00:53/00:02:06, flags: PT Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.0.1.40), 00:13:10/00:02:58, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:13:10/00:00:00 --More--   R4# RACK15AS>6 [Resuming connection 6 to r6 ... ] ........................ S6#pin 224.5.5.5 repeat 1000000~ repeat 1000000 repeat 1000000  repeat 1000000 4 repeat 1000000 Type escape sequence to abort. Sending 1000000, 100-byte ICMP Echos to 224.5.5.4, timeout is 2 seconds: RACK15AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 30 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 6 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 25 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 00:24:09.363: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 00:25:53.739: PIM(0): Insert (180.40.7.97,224.5.5.4) prune in nbr 180.40.7.129's queue *Mar 1 00:25:53.739: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 00:25:53.739: PIM(0): Adding v2 (180.40.7.97/32, 224.5.5.4) Prune *Mar 1 00:25:53.739: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) R4#sh deb IP multicast: PIM debugging is on R4#deb ip pim ? Hostname or A.B.C.D IP group address atm PIM ATM signalling activity auto-rp Auto-RP bsr PIM Candidate-RP/BSR activity df PIM RP designated forwarder election activity hello PIM Hello packets tag PIM multicast tagswitching activity vrf Select VPN Routing/Forwarding instance R4#deb ip pim     mu R4#deb ip mu ? mbgp mcache mhbeat mobile mpacket mrm mrouting msdp mtag R4#deb ip mp R4#deb ip mpacket IP multicast packets debugging is on R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa 0/0 R4(config-if)#shut R4(config-if)# *Mar 1 00:26:38.699: %PIM-5-NBRCHG: neighbor 180.40.7.129 DOWN on interface FastEthernet0/0 (vrf default) non DR *Mar 1 00:26:38.703: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-if)# *Mar 1 00:26:38.767: PIM(0): Prune FastEthernet0/0/224.5.5.4 from (*, 224.5.5.4) *Mar 1 00:26:38.767: PIM(0): Prune FastEthernet0/0/224.5.5.5 from (*, 224.5.5.5) R4(config-if)# *Mar 1 00:26:40.699: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down R4(config-if)#no shu *Mar 1 00:26:40.767: PIM(0): Prune FastEthernet0/0/224.4.4.4 from (*, 224.4.4.4) *Mar 1 00:26:40.767: PIM(0): Prune FastEthernet0/0/224.0.1.40 from (*, 224.0.1.40) R4(config-if)#no shut *Mar 1 00:26:41.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down R4(config-if)#no shut R4(config-if)# *Mar 1 00:26:44.651: PIM(0): Check DR after interface: FastEthernet0/0 came up! *Mar 1 00:26:44.651: PIM(0): Changing DR for FastEthernet0/0, from 0.0.0.0 to 180.40.7.130 (this system) *Mar 1 00:26:44.651: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.130 on interface FastEthernet0/0 (vrf default) R4(config-if)# *Mar 1 00:26:44.671: PIM(0): Building Graft message for 224.4.4.4, FastEthernet0/0: no entries *Mar 1 00:26:44.671: PIM(0): Building Graft message for 224.0.1.40, FastEthernet0/0: no entries R4(config-if)# *Mar 1 00:26:44.859: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 00:26:45.859: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R4(config-if)# *Mar 1 00:26:46.651: PIM(0): Check DR after interface: FastEthernet0/0 came up! R4(config-if)#^Z R4# R4# R4# R4# *Mar 1 00:26:51.119: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.5.5.4), 00:01:19/stopped, RP 0.0.0.0, flags: DP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (180.40.7.97, 224.5.5.4), 00:01:19/00:01:40, flags: PT Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.4.4.4), 00:15:52/00:02:31, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:00:29/00:00:00 (*, 224.5.5.5), 00:03:44/00:02:15, RP 0.0.0.0, flags: DP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.0.1.40), 00:16:01/00:02:30, RP 0.0.0.0, flags: DC --More--   Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:00:33/00:00:00 R4# *Mar 1 00:27:26.155: %PIM-5-NBRCHG: neighbor 180.40.7.129 UP on interface FastEthernet0/0 (vrf default) *Mar 1 00:27:26.159: PIM(0): Add FastEthernet0/0/180.40.7.129 to (180.40.7.97, 224.5.5.4), Forward state, by PIM *G Join *Mar 1 00:27:26.159: PIM(0): Add FastEthernet0/0/180.40.7.129 to (*, 224.5.5.4), Forward state, by PIM *G Join *Mar 1 00:27:26.163: PIM(0): Update FastEthernet0/0/180.40.7.129 to (*, 224.4.4.4), Forward state, by PIM *G Join *Mar 1 00:27:26.163: PIM(0): Add FastEthernet0/0/180.40.7.129 to (*, 224.5.5.5), Forward state, by PIM *G Join *Mar 1 00:27:26.163: PIM(0): Update FastEthernet0/0/180.40.7.129 to (*, 224.0.1.40), Forward state, by PIM *G Join *Mar 1 00:27:26.171: PIM(0): Building Graft message for 224.0.1.40, FastEthernet0/0: no entries R4# *Mar 1 00:27:26.171: PIM(0): Building Graft message for 224.5.5.5, FastEthernet0/0: no entries *Mar 1 00:27:26.171: PIM(0): Building Graft message for 224.4.4.4, FastEthernet0/0: no entries *Mar 1 00:27:26.171: PIM(0): Building Graft message for 224.5.5.4, FastEthernet0/0: no entries R4# *Mar 1 00:27:30.879: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4#sh deb Generic IP: IP multicast packets debugging is on IP multicast: PIM debugging is on R4#clea logg Clear logging buffer [confirm] R4# RACK15AS>3 [Resuming connection 3 to r3 ... ] *Mar 1 R3#clea ip mrout * R3# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4# *Mar 1 00:28:31.679: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=137, prot=1, len=114(100), mroute olist null R4#sh log *Mar 1 00:28:33.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=138, prot=1, len=114(100), mroute olist null R4#sh log *Mar 1 00:28:35.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=139, prot=1, len=114(100), mroute olist null R4#sh log  *Mar 1 00:28:37.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=140, prot=1, len=114(100), mroute olist null R4#sh lo      *Mar 1 00:28:39.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=141, prot=1, len=114(100), mroute olist null R4# *Mar 1 00:28:41.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=142, prot=1, len=114(100), mroute olist null R4# *Mar 1 00:28:43.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=143, prot=1, len=114(100), mroute olist null R4# *Mar 1 00:28:45.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=144, prot=1, len=114(100), mroute olist null R4# *Mar 1 00:28:47.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=145, prot=1, len=114(100), mroute olist null R4# *Mar 1 00:28:49.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=146, prot=1, len=114(100), mroute olist null R4# *Mar 1 00:28:51.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=147, prot=1, len=114(100), mroute olist null R4# *Mar 1 00:28:53.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=148, prot=1, len=114(100), mroute olist null R4# *Mar 1 00:28:55.647: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=149, prot=1, len=114(100), mroute olist null *Mar 1 00:28:55.683: PIM(0): Insert (180.40.7.97,224.5.5.4) prune in nbr 180.40.7.129's queue *Mar 1 00:28:55.683: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 00:28:55.683: PIM(0): Adding v2 (180.40.7.97/32, 224.5.5.4) Prune *Mar 1 00:28:55.683: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) *Mar 1 00:28:55.687: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=149, prot=1, len=114(100), mroute olist null R4#u all     u all All possible debugging has been turned off R4#deb ip pim ? Hostname or A.B.C.D IP group address atm PIM ATM signalling activity auto-rp Auto-RP bsr PIM Candidate-RP/BSR activity df PIM RP designated forwarder election activity hello PIM Hello packets tag PIM multicast tagswitching activity vrf Select VPN Routing/Forwarding instance R4#deb ip pim     m? mbgp mcache mhbeat mobile mpacket mrm mrouting msdp mtag R4#deb ip m pim > ? Hostname or A.B.C.D IP group address atm PIM ATM signalling activity auto-rp Auto-RP bsr PIM Candidate-RP/BSR activity df PIM RP designated forwarder election activity hello PIM Hello packets tag PIM multicast tagswitching activity vrf Select VPN Routing/Forwarding instance R4#deb ip pim PIM debugging is on R4# RACK15AS>67~ % Unknown command or computer name, or unable to find computer address RACK15AS> [Resuming connection 4 to r4 ... ] [Special telnet escape help] ^^B sends telnet BREAK ^^C sends telnet IP ^^H sends telnet EC ^^O sends telnet AO ^^T sends telnet AYT ^^U sends telnet EL R4# R4# RACK15AS>6 [Resuming connection 6 to r6 ... ] ... RACK15AS>4 [Resuming connection 4 to r4 ... ] R4# R4# R4# R4# R4# R4# R4# R4# R4#sh pim int de ^ % Invalid input detected at '^' marker. R4#sh pim int de ipim int deppim int de pim int de FastEthernet0/0 is up, line protocol is up Internet address is 180.40.7.130/27 Multicast switching: fast Multicast packets in/out: 27/0 Multicast boundary: not set Multicast TTL threshold: 0 PIM: enabled PIM version: 2, mode: dense PIM DR: 180.40.7.130 (this system) PIM neighbor count: 1 PIM Hello/Query interval: 30 seconds PIM State-Refresh processing: enabled PIM State-Refresh origination: enabled, interval: 8 seconds PIM NBMA mode: disabled PIM ATM multipoint signalling: disabled PIM domain border: disabled Multicast Tagswitching: disabled R4#sh deb IP multicast: PIM debugging is on R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 153 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 129 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 35 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 00:28:31.679: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=137, prot=1, len=114(100), mroute olist null *Mar 1 00:28:33.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=138, prot=1, len=114(100), mroute olist null *Mar 1 00:28:35.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=139, prot=1, len=114(100), mroute olist null *Mar 1 00:28:37.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=140, prot=1, len=114(100), mroute olist null *Mar 1 00:28:39.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=141, prot=1, len=114(100), mroute olist null *Mar 1 00:28:41.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=142, prot=1, len=114(100), mroute olist null *Mar 1 00:28:43.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=143, prot=1, len=114(100), mroute olist null *Mar 1 00:28:45.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=144, prot=1, len=114(100), mroute olist null *Mar 1 00:28:47.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=145, prot=1, len=114(100), mroute olist null *Mar 1 00:28:49.675: IP(0): s=180.40.7.97 (FastEthernet0/0) d=224.5.5.4 id=146, prot=1, len=114(100), mroute olist null --More--   R4#clea logg Clear logging buffer [confirm] R4#sh   log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 153 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 129 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 35 message lines logged --More--   --More--  Log Buffer (4096 bytes): R4#sh run int fa 0/9 0 Building configuration... Current configuration : 208 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 8 ip pim dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4# *Mar 1 00:31:57.707: PIM(0): Insert (180.40.7.97,224.5.5.4) prune in nbr 180.40.7.129's queue *Mar 1 00:31:57.707: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 00:31:57.707: PIM(0): Adding v2 (180.40.7.97/32, 224.5.5.4) Prune *Mar 1 00:31:57.707: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) R4#conf t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip pim st R4(config)#ip pim state-refresh en R4(config)#ip pim state-refresh en  ? disable Disable PIM State-Refresh processing R4(config)#ip pim state-refresh                       RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip pim int de FastEthernet0/1 is up, line protocol is up Internet address is 180.40.7.129/27 Multicast switching: fast Multicast packets in/out: 1/30 Multicast boundary: not set Multicast TTL threshold: 0 PIM: enabled PIM version: 2, mode: sparse-dense PIM DR: 180.40.7.130 PIM neighbor count: 1 PIM Hello/Query interval: 30 seconds PIM State-Refresh processing: enabled PIM State-Refresh origination: disabled PIM NBMA mode: disabled PIM ATM multipoint signalling: disabled PIM domain border: disabled Multicast Tagswitching: disabled Serial1/0 is up, line protocol is up Internet address is 180.40.7.33/27 Multicast switching: fast Multicast packets in/out: 279/1 Multicast boundary: not set Multicast TTL threshold: 0 --More--   R3# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4(config)#^Z R4# R4# *Mar 1 00:33:09.819: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4# R4# R4#shg lo     logg Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 159 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 135 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 36 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 00:31:57.707: PIM(0): Insert (180.40.7.97,224.5.5.4) prune in nbr 180.40.7.129's queue *Mar 1 00:31:57.707: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 00:31:57.707: PIM(0): Adding v2 (180.40.7.97/32, 224.5.5.4) Prune *Mar 1 00:31:57.707: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) *Mar 1 00:33:09.819: %SYS-5-CONFIG_I: Configured from console by console R4#u all All possible debugging has been turned off R4#wr Building configuration... [OK] R4#sh run int fa 0/0 Building configuration... Current configuration : 208 bytes ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip nat inside ip pim state-refresh origination-interval 8 ip pim dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto end R4# R4#reload Proceed with reload? [confirm] *Mar 1 00:35:49.947: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command. System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Copyright (c) 1999 by cisco Systems, Inc. C3600 processor with 65536 Kbytes of main memory Main memory is configured to 32 bit mode with parity disabled RACK15AS> [Resuming connection 4 to r4 ... ] RACK15AS>3 [Resuming connection 3 to r3 ... ] *Ma R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#access-list *Mar 1 00:35:15.294: %PIM-5-NBRCHG: neighbor 180.40.7.130 DOWN on interface FastEthernet0/1 (vrf default) DR *Mar 1 00:35:15.294: %PIM-5-DRCHG: DR change from neighbor 180.40.7.130 to 180.40.7.129 on interface FastEthernet0/1 (vrf default) R3(config)#access-list 1 den 224.20.68.1 R3(config)#access-list 1 per any R3(config)#ip rp R3(config)#ip rp-ad R3(config)#ip rp-add R3(config)#ip rp-add      pim rp-add R3(config)#ip pim rp-address ? A.B.C.D IP address of Rendezvous-point for group R3(config)#ip pim rp-address 180.40.7.129 ? <1-99> Access-list reference for group <1300-1999> Access-list reference for group (expanded range) WORD IP Named Standard Access list override Overrides dynamically learnt RP mappings R3(config)#ip pim rp-address 180.40.7.129 1 ? override Overrides dynamically learnt RP mappings R3(config)#ip pim rp-address 180.40.7.129 1 R3(config)# *Mar 1 00:36:05.729: %PIM-5-NBRCHG: neighbor 180.40.7.130 UP on interface FastEthernet0/1 (vrf default) *Mar 1 00:36:05.729: %PIM-5-DRCHG: DR change from neighbor 180.40.7.129 to 180.40.7.130 on interface FastEthernet0/1 (vrf default) R3(config)#do    ^Z R3#h sh *Mar 1 00:36:11.162: %SYS-5-CONFIG_I: Configured from console by console *Mar 1 00:36:11.679: %OSPF-5-ADJCHG: Process 1, Nbr 192.10.32.15 on FastEthernet0/1 from LOADING to FULL, Loading Done R3#h sh run          sh run | b ip pim rp ip pim rp-address 180.40.7.129 1 ! access-list 1 deny 224.20.68.1 access-list 1 permit any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end --More--   R3# RACK15AS>1 [Resuming connection 1 to r1 ... ]   shutdown --More--   R1#coni fo i t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#ip pim rp-address 180.40.7.129 1 R1(config)#! R1(config)#access-list 1 deny 224.20.68.1 R1(config)#access-list 1 permit any R1(config)#! R1(config)#^Z R1#x2 * *Mar 1 00:38:19.721: %SYS-5-CONFIG_I: Configured from console by console *co   * * *exit R1#con    RACK15AS>2 [Resuming connection 2 to r2 ... ] *Ma R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#ip pim rp-address 180.40.7.129 1 R2(config)#! R2(config)#access-list 1 deny 224.20.68.1 R2(config)#access-list 1 permit any R2(config)#! R2(config)#^Z R2# RACK15AS>4 5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#ip pim rp-address 180.40.7.129 1 S5(config)#! S5(config)#access-list 1 deny 224.20.68.1 S5(config)#access-list 1 permit any S5(config)#! S5(config)#^Z S5# RACK15AS>6 [Resuming connection 6 to r6 ... ] .... RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#ip pim rp-address 180.40.7.129 1 R7(config)#! R7(config)#access-list 1 deny 224.20.68.1 R7(config)#access-list 1 permit any R7(config)#! R7(config)# RACK15AS>4 [Resuming connection 4 to r4 ... ] pro R4> R4> R4>en R4#deb ip pim PIM debugging is on R4# R4# R4# R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 16 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 16 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 21 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 00:00:04.183: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up *Mar 1 00:00:17.111: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 00:00:18.115: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up *Mar 1 00:00:18.827: %SYS-5-CONFIG_I: Configured from memory by console *Mar 1 00:00:20.263: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up *Mar 1 00:00:20.779: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down *Mar 1 00:00:21.391: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up *Mar 1 00:00:22.107: %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3620-IK9O3S7-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Thu 10-Nov-05 03:19 by evmiller *Mar 1 00:00:22.115: %SNMP-5-COLDSTART: SNMP agent on host R4 is undergoing a cold start --More--  *Mar 1 00:00:24.539: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.130 on interface FastEthernet0/0 (vrf default) *Mar 1 00:00:24.751: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up *Mar 1 00:00:25.751: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down *Mar 1 00:00:28.539: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 180.40.7.130 on interface FastEthernet0/0 (vrf default) *Mar 1 00:00:29.115: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up *Mar 1 00:00:58.479: %PIM-5-NBRCHG: neighbor 180.40.7.129 UP on interface FastEthernet0/0 (vrf default) *Mar 1 00:01:04.435: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4# R4# R4# R4# R4#clea ip    logg Clear logging buffer [confirm] R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:03:04/00:02:37, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:02:54/00:00:00 (*, 224.0.1.40), 00:03:04/00:02:40, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:02:53/00:00:00 R4# RACK15AS>2 [Resuming connection 2 to r2 ... ] *Mar R2# R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#!access-list 1 permit anydeny 224.20.68.1! ip pim rp-address 180.40.7.129 1nip pim rp-address 180.40.7.129 1oip pim rp-address 180.40.7.129 1 ip pim rp-address 180.40.7.129 1 R2(config)# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pim rp-address 180.40.7.129 1 nip pim rp-address 180.40.7.129 1 oip pim rp-address 180.40.7.129 1  ip pim rp-address 180.40.7.129 1  R3(config)# RACK15AS>4 [Resuming connection 4 to r4 ... ] *Mar 1 00:03:43.755: PIM(0): Insert (180.40.7.97,224.5.5.4) prune in nbr 180.40.7.129's queue *Mar 1 00:03:43.755: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 00:03:43.755: PIM(0): Adding v2 (180.40.7.97/32, 224.5.5.4) Prune *Mar 1 00:03:43.755: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) R4# R4# R4# R4# R4# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3(config)#int f a0/0 ^ % Invalid input detected at '^' marker. R3(config)#fa 0/0 ^ % Invalid input detected at '^' marker. R3(config)#fa 0/0a\  ifa 0/0nfa 0/0tfa 0/0 fa 0/0 R3(config-if)#ip pim st R3(config-if)#ip pim state-refresh 8 ^ % Invalid input detected at '^' marker. R3(config-if)#ip pim state-refresh 8 i o 8 R3(config-if)# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4# R4# R4# R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int fa / 0/0 R4(config-if)#\ ip pim st R4(config-if)#ip pim state-refresh 10 ^ % Invalid input detected at '^' marker. R4(config-if)#ip pim state-refresh 10o10 10 R4(config-if)#^Z R4# *Mar 1 00:05:07.031: %SYS-5-CONFIG_I: Configured from console by console R4#sh ver Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3620-IK9O3S7-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Thu 10-Nov-05 03:19 by evmiller Image text-base: 0x60008B00, data-base: 0x6193C000 ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) ROM: 3600 Software (C3620-IK9O3S7-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) R4 uptime is 5 minutes System returned to ROM by reload System image file is "flash:flash:c3620-ik9o3s7-mz.123-16a.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you --More--   R4#sh deb IP multicast: PIM debugging is on R4#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled) Console logging: level debugging, 22 messages logged, xml disabled Monitor logging: level debugging, 0 messages logged, xml disabled Buffer logging: level debugging, 22 messages logged, xml disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Trap logging: level informational, 22 message lines logged --More--   Log Buffer (4096 bytes): *Mar 1 00:03:43.755: PIM(0): Insert (180.40.7.97,224.5.5.4) prune in nbr 180.40.7.129's queue *Mar 1 00:03:43.755: PIM(0): Building Join/Prune packet for nbr 180.40.7.129 *Mar 1 00:03:43.755: PIM(0): Adding v2 (180.40.7.97/32, 224.5.5.4) Prune *Mar 1 00:03:43.755: PIM(0): Send v2 join/prune to 180.40.7.129 (FastEthernet0/0) *Mar 1 00:05:07.031: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4# R4# R4# R4# R4# R4#deb ip mr p R4#deb ip mpacket IP multicast packets debugging is on R4#deb ip pim ? Hostname or A.B.C.D IP group address atm PIM ATM signalling activity auto-rp Auto-RP bsr PIM Candidate-RP/BSR activity df PIM RP designated forwarder election activity hello PIM Hello packets tag PIM multicast tagswitching activity vrf Select VPN Routing/Forwarding instance R4#deb ip pim  hello PIM-HELLO debugging is on R4# *Mar 1 00:06:24.075: PIM(0): Received v2 hello on FastEthernet0/0 from 180.40.7.129 R4# *Mar 1 00:06:25.527: PIM(0): Send periodic v2 Hello on FastEthernet0/0 R4#u la  all All possible debugging has been turned off R4# RACK15AS>2 [Resuming connection 2 to r2 ... ] * R2(config)#no ip pim rp-address 180.40.7.129 1no ip pim rp-address 180.40.7.129 1  ip pim rp-address 180.40.7.129 1  R2(config)# RACK15AS>3 [Resuming connection 3 to r3 ... ] * R3(config-if)# *Mar 1 00:41:52.898: %PIM-1-INVALID_RP_REG: Received Register from 180.40.7.2 for 224.5.5.4, not willing to be RP R3(config-if)#ip pim state-refresh o 8 R3(config-if)#ip pim state-refresh o 88 nt fa 0/0 fa 0/0 int f a0/0no ip pim rp-address 180.40.7.129 1 no ip pim rp-address 180.40.7.129 1  ip pim rp-address 180.40.7.129 1  R3(config)#^Z R3# *Mar 1 00:42:03.323: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# R3# R3# RACK15AS>6 [Resuming connection 6 to r6 ... ] .... S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim rp-address 180.40.7.129 1 S6(config)#! S6(config)#access-list 1 deny 224.20.68.1 S6(config)#access-list 1 permit any S6(config)#! S6(config)#^Z S6# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7(config)#!access-list 1 permit any!  ^Z R7#p *Mar 1 00:42:22.246: %SYS-5-CONFIG_I: Configured from console by console R7#ping      sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:04:32/00:02:40, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null R7#piun  mng    ing 224.6 5 6.6.6.  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: . R7#ping 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 88 ms R7# R7# R7# R7# R7# R7# RACK15AS>1 [Resuming connection 1 to r1 ... ] R1#shg    ip ro    mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.5.5.4), 00:05:53/00:01:55, RP 180.40.7.129, flags: SP Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null (*, 224.6.6.6), 00:00:14/stopped, RP 180.40.7.129, flags: SP Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Null (17.100.1.2, 224.6.6.6), 00:00:14/00:03:24, flags: T Incoming interface: Ethernet0/1, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0.2, Forward/Sparse-Dense, 00:00:12/00:03:17 (*, 224.0.1.40), 00:05:55/00:02:59, RP 180.40.7.129, flags: SJCL Incoming interface: Serial0/0.2, RPF nbr 180.40.7.65 Outgoing interface list: Ethernet0/1, Forward/Sparse-Dense, 00:05:55/00:03:21 Ethernet0/0, Forward/Sparse-Dense, 00:05:55/00:03:11 --More--   R1# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#ping 224.6.6.6 p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 124 ms R7# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4#p 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 64 ms R4#p 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 60 ms R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.5.5.4), 00:04:58/00:01:01, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:04:58/00:00:00 (*, 224.4.4.4), 00:08:24/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:08:14/00:00:00 (17.100.1.2, 224.4.4.4), 00:00:35/00:02:23, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.0.1.40), 00:08:25/00:02:21, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:08:14/00:00:00 --More--   R4# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#conf t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#int fa 0/1 R7(config-if)#ip igmp join R7(config-if)#ip igmp join-group 224.7.7.7.  R7(config-if)#^Z R7# RACK15AS>4 [Resuming connection 4 to r4 ... ] p 224.7.7.7 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 124 ms R4#int     cop  onfi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#in tlo 0 ^ % Invalid input detected at '^' marker. R4(config)#u ~int      int lo 0 R4(config-if)#iop    p add 4.4.4.4 255.255.22~55.     55.0 R4(config-if)#ip pim       igmp joi R4(config-if)#ip igmp join-group 224.44.44.44 R4(config-if)#^Z R4# RACK15AS>7 [Resuming connection 7 to r7 ... ] *Marpin 224.44.44.44 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.44.44.44, timeout is 2 seconds: . R7# R7# R7# R7# R7# R7#pin 224.44.44.44 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.44.44.44, timeout is 2 seconds: . R7# RACK15AS>4 [Resuming connection 4 to r4 ... ] *Mar R4#sh ip m  route IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:10:36/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:10:26/00:00:00 (17.100.1.2, 224.4.4.4), 00:02:46/00:00:13, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.0.1.40), 00:10:37/00:02:04, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:10:26/00:00:00 R4#con  fi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int l o0 ^ % Invalid input detected at '^' marker. R4(config)#int l o0o0  R4(config-if)#ip pim de R4(config-if)#ip pim dense-mode R4(config-if)#^Z R4# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#pin 224.44.44.44 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.44.44.44, timeout is 2 seconds: . R7#pin 224.44.44.44 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.44.44.44, timeout is 2 seconds: . R7# RACK15AS>4 [Resuming connection 4 to r4 ... ] *Mar 1 0 R4#confi tsh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:11:16/00:02:32, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:11:06/00:00:00 (*, 224.0.1.40), 00:11:17/00:02:28, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:11:05/00:00:00 (*, 224.44.44.44), 00:00:14/00:02:46, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:00:14/00:00:00 FastEthernet0/0, Forward/Dense, 00:00:14/00:00:00 R4#^x3 % Unknown command or computer name, or unable to find computer address R4# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#ip pim de R3(config-if)#ip pim dense-mode ? proxy-register Send proxy registers R3(config-if)#ip pim dense-mode pre  R3(config-if)#ip pim dense-mode proxy-register ? list Access list route-map Route-map R3(config-if)#ip pim dense-mode proxy-register lo  R3(config-if)#ip pim dense-mode proxy-register list ? <100-199> Extended access list number <2000-2699> Extended access list number (expanded range) WORD IP named extended access list R3(config-if)#ip pim dense-mode proxy-register list 1 ? R3(config-if)#ip pim dense-mode proxy-register list 1                                         access-list             ip pim dense-mode proxy-register list 1 Warning: PIM register rate-limit set to 2 messages per second % Invalid access list name. R3(config-if)#ip pim dense-mode proxy-register list 1                                       exit R3(config)# ip a     access-list 100 per any a     ip any any R3(config)#int fa 0/0 R3(config-if)#int fa 0/0access-list 100 per ip any anyexit ip pim dense-mode proxy-register list 100 R3(config-if)#^Z R3# *Mar 1 00:49:10.680: %SYS-5-CONFIG_I: Configured from console by console R3# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#pin 224.44.44.44 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.44.44.44, timeout is 2 seconds: . R7#pin 224.44.44.44 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.44.44.44, timeout is 2 seconds: . R7#pin 224.44.44.44 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.44.44.44, timeout is 2 seconds: . R7# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4#ping 244.          RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:11:52/00:02:07, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.6.6.6), 00:08:19/00:03:09, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:08:16/00:03:09 (*, 224.7.7.7), 00:06:48/00:02:36, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:06:49/00:02:35 (*, 224.0.1.40), 00:12:17/00:02:59, RP 180.40.7.129, flags: SL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:08:16/00:03:05 --More--   --More--  (*, 224.44.44.44), 00:05:27/stopped, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (17.100.1.2, 224.44.44.44), 00:01:43/00:01:16, flags: P Incoming interface: Serial1/0, RPF nbr 180.40.7.35 Outgoing interface list: Null R3# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int fa 0/0 R3(config-if)#int fa 0/0p pim dense-mode proxy-register list 100nip pim dense-mode proxy-register list 100oip pim dense-mode proxy-register list 100 ip pim dense-mode proxy-register list 100 R3(config-if)#ip pim sp R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4#^x3sh ip mrouteconfi t sh ip mrouteconfi t p 224.7.7.7sh ip mroutep 224.6.6.6 sh ip mroutep 224.7.7.7  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.7.7.7, timeout is 2 seconds: Reply to request 0 from 17.100.1.2, 148 ms Reply to request 0 from 17.100.1.2, 148 ms R4# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3(config-if)#do sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:13:17/00:02:44, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 224.6.6.6), 00:09:44/00:02:45, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:09:41/00:02:45 (*, 224.7.7.7), 00:08:13/stopped, RP 180.40.7.129, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:08:14/00:03:07 (4.4.4.4, 224.7.7.7), 00:00:09/00:03:24, flags: T Incoming interface: FastEthernet0/1, RPF nbr 180.40.7.130 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:00:09/00:03:20 --More--   --More--  (180.40.7.130, 224.7.7.7), 00:00:19/00:03:14, flags: T --More--   Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0 --More--   Outgoing interface list: --More--   Serial1/0, Forward/Sparse-Dense, 00:00:19/00:03:10 (*, 224.0.1.40), 00:14:07/00:03:15, RP 180.40.7.129, flags: SL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/0, Forward/Sparse-Dense, 00:10:06/00:03:15 (*, 224.44.44.44), 00:07:14/00:02:30, RP 180.40.7.129, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null R3(config-if)# RACK15AS> [Resuming connection 3 to r3 ... ] R3(config-if)#do sh ip mrouteip pim sparse-dense-mode no ip pim dense-mode proxy-register list 100no ip pim dense-mode proxy-register list 100  ip pim dense-mode proxy-register list 100  R3(config-if)#^Z R3#sh run *Mar 1 00:53:28.622: %SYS-5-CONFIG_I: Configured from console by console R3#sh run int fa 0/0 Building configuration... Current configuration : 171 bytes ! interface FastEthernet0/0 no ip address ip pim state-refresh origination-interval 8 ip pim dense-mode proxy-register list 100 shutdown duplex auto speed auto end R3# RACK15AS>1 [Resuming connection 1 to r1 ... ] R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#confi t ^ % Invalid input detected at '^' marker. R1(config)# R1(config)#no ip pim rp-add 180.40.7.129 1 R1(config)#no access-list 1 R1(config)# R1(config)# R1(config)#end R1# *Mar 1 01:00:21.079: %SYS-5-CONFIG_I: Configured from console by console R1# RACK15AS>2 [Resuming connection 2 to r2 ... ] confi t ^ % Invalid input detected at '^' marker. R2(config)# R2(config)#no ip pim rp-add 180.40.7.129 1 R2(config)#no access-list 1 R2(config)# R2(config)# R2(config)#end R2# *Mar 1 00:59:15.203: %SYS-5-CONFIG_I: Configured from console by console R2# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4# RACK15AS>5 [Resuming connection 5 to r5 ... ] 00:4 S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#no ip pim rp-add 180.40.7.129 1 S5(config)#no access-list 1 S5(config)# S5(config)# S5(config)#end S5# RACK15AS>6 [Resuming connection 6 to r6 ... ] 00: S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#no ip pim rp-add 180.40.7.129 1 S6(config)#no access-list 1 S6(config)# S6(config)# S6(config)#end S6# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#no ip pim rp-add 180.40.7.129 1 R7(config)#no access-list 1 R7(config)# R7(config)# R7(config)#end R7# *Mar 1 00:59:22.390: %SYS-5-CONFIG_I: Configured from console by console R7# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#no ip pim rp-add 180.40.7.129 1 R3(config)# RACK15AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim ? accept-register Registers accept filter accept-rp RP accept filter autorp Configure AutoRP global operations bidir-enable Enable Bidir-PIM bsr-candidate Candidate bootstrap router (candidate BSR) log-neighbor-changes Log PIM neighbor up/down and DR changes register-rate-limit Rate limit for PIM data registers register-source Source address for PIM Register rp-address PIM RP-address (Rendezvous Point) rp-announce-filter Auto-RP announce message filter rp-candidate To be a PIMv2 RP candidate send-rp-announce Auto-RP send RP announcement send-rp-discovery Auto-RP send RP discovery message (as RP-mapping agent) spt-threshold Source-tree switching threshold ssm Configure Source Specific Multicast state-refresh PIM DM State-Refresh configuration vrf Select VPN Routing/Forwarding instance R2(config)#ip pim send-rp-discovery ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing scope Scope of the RP discovery packets R2(config)#ip pim send-rp-discovery scop ? <1-255> TTL R2(config)#ip pim send-rp-discovery scop 3 R2(config)#^Z R2# *Mar 1 01:01:37.981: %SYS-5-CONFIG_I: Configured from console by console R2#sh run | b i ip    send ip pim send-rp-discovery scope 3 R2# R2#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.6.6.6), 00:02:55/00:02:47, RP 0.0.0.0, flags: DC Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:02:55/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:02:55/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:02:55/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:02:55/00:00:00 (*, 224.0.1.39), 00:00:47/00:02:52, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:00:47/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:00:47/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:00:47/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:00:47/00:00:00 (*, 224.0.1.40), 00:03:06/00:02:38, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 --More--   Outgoing interface list: Serial1/2, Forward/Sparse-Dense, 00:03:09/00:00:00 Serial1/0.2, Forward/Sparse-Dense, 00:03:09/00:00:00 Serial1/0.1, Forward/Sparse-Dense, 00:03:09/00:00:00 FastEthernet0/1, Forward/Sparse-Dense, 00:03:09/00:00:00 R2# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3(config)#do sh access-list Standard IP access list 1 10 deny 224.20.68.1 20 permit any (743 matches) Extended IP access list 100 10 permit ip any any R3(config)#ip pim sen R3(config)#ip pim send-rp-a R3(config)#ip pim send-rp-announce ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config)#ip pim send-rp-announce fa R3(config)#ip pim send-rp-announce fastEthernet 0/1 ? scope RP announcement scope R3(config)#ip pim send-rp-announce fastEthernet 0/1 sc R3(config)#ip pim send-rp-announce fastEthernet 0/1 scope ? <1-255> TTL of the RP announce packet R3(config)#ip pim send-rp-announce fastEthernet 0/1 scope 1 ? group-list Group access-list interval RP announcement interval R3(config)#ip pim send-rp-announce fastEthernet 0/1 scope 1 gr R3(config)#ip pim send-rp-announce fastEthernet 0/1 scope 1 group-list 1 ? interval RP announcement interval R3(config)#ip pim send-rp-announce fastEthernet 0/1 scope 1 group-list 1 in 5 R3(config)#^Z R3# *Mar 1 01:03:27.869: %SYS-5-CONFIG_I: Configured from console by console R3# R3# R3# R3# RACK15AS>2 [Resuming connection 2 to r2 ... ] R2#h sh ip pim rp map PIM Group-to-RP Mappings This system is an RP-mapping agent Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.129 (?), elected via Auto-RP Uptime: 00:00:14, expires: 00:00:11 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.129 (?), elected via Auto-RP Uptime: 00:00:14, expires: 00:00:11 R2# R2# R2# R2# R2# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:45, expires: 00:02:10 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:45, expires: 00:02:15 R7# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4#sh i  p pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:54, expires: 00:02:02 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:54, expires: 00:02:04 R4# R4# R4# R4# R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:29:01/00:02:44, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.0.1.40), 00:29:01/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:28:50/00:00:00 (180.40.7.2, 224.0.1.40), 00:01:01/00:02:58, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (180.40.7.35, 224.0.1.40), 00:01:01/00:02:58, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.44.44.44), 00:17:58/00:02:52, RP 180.40.7.129, flags: SJCL --More--   Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:18:01/00:00:00 R4# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip pim rp mapconfi t pin 224.44.44.44 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.44.44.44, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 124 ms R7# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:29:25/00:02:20, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.0.1.40), 00:29:25/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:29:14/00:00:00 (180.40.7.2, 224.0.1.40), 00:01:25/00:02:34, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (180.40.7.35, 224.0.1.40), 00:01:25/00:02:34, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.44.44.44), 00:18:22/stopped, RP 180.40.7.129, flags: SJCL --More--   Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:18:22/00:00:00 (17.100.1.2, 224.44.44.44), 00:00:11/00:02:56, flags: LJT Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:00:11/00:00:00 R4# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b             RACK15AS>4 [Resuming connection 4 to r4 ... ] R4#conf t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip    np    ip pim ? accept-register Registers accept filter accept-rp RP accept filter autorp Configure AutoRP global operations bidir-enable Enable Bidir-PIM bsr-candidate Candidate bootstrap router (candidate BSR) log-neighbor-changes Log PIM neighbor up/down and DR changes register-rate-limit Rate limit for PIM data registers register-source Source address for PIM Register rp-address PIM RP-address (Rendezvous Point) rp-announce-filter Auto-RP announce message filter rp-candidate To be a PIMv2 RP candidate send-rp-announce Auto-RP send RP announcement send-rp-discovery Auto-RP send RP discovery message (as RP-mapping agent) spt-threshold Source-tree switching threshold ssm Configure Source Specific Multicast state-refresh PIM DM State-Refresh configuration vrf Select VPN Routing/Forwarding instance R4(config)#ip pim ac R4(config)#ip pim accept-rp ? A.B.C.D IP address of RP for group auto-rp only RP-mapping from Auto-RP R4(config)#ip pim accept-rp au / ? <1-99> Access-list reference for group <1300-1999> Access-list reference for group (expanded range) WORD IP Named Standard Access list R4(config)#ip pim accept-rp au nip pim accept-rp au oip pim accept-rp au  ip pim accept-rp au  R4(config)#^Z R4#sh ip pi *Mar 1 00:32:09.219: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip pim p rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:03:55, expires: 00:02:03 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:03:55, expires: 00:02:02 R4#q ~ clea ip pim rp * ^ % Invalid input detected at '^' marker. R4#clea ip pim rp * ? A.B.C.D RP address R4#clea ip pim rp R4#clea ip pim rp *sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip pim rp map PIM Group-to-RP Mappings R4#sh ip mrotue ^ % Invalid input detected at '^' marker. R4#sh ip mrotueue ute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:20/00:02:39, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:00:20/00:00:00 (*, 224.0.1.40), 00:32:26/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:32:15/00:00:00 (180.40.7.2, 224.0.1.40), 00:04:26/00:02:32, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (180.40.7.35, 224.0.1.40), 00:04:26/00:02:32, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null --More--  (*, 224.44.44.44), 00:00:23/00:02:36, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Loopback0, Forward/Dense, 00:00:23/00:00:00 FastEthernet0/0, Forward/Dense, 00:00:23/00:00:00 R4# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b   i send ip pim send-rp-announce FastEthernet0/1 scope 1 group-list 1 interval 5 R3# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:01:01/00:02:51, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.0.1.40), 00:33:07/stopped, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 00:32:56/00:00:00 (180.40.7.2, 224.0.1.40), 00:05:07/00:02:50, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (180.40.7.35, 224.0.1.40), 00:05:07/00:02:50, flags: PLTX Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Null (*, 224.44.44.44), 00:01:03/00:02:50, RP 180.40.7.129, flags: SJCL --More--   Incoming interface: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:01:03/00:00:00 R4#sh ip mroutetuepim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:18, expires: 00:02:40 Group(s) (-)224.20.68.1/32 RP 180.40.7.129 (?), v2v1 Info source: 180.40.7.65 (?), elected via Auto-RP Uptime: 00:00:18, expires: 00:02:37 R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#no ip pim accept-rp au no ip pim accept-rp au  ip pim accept-rp au  R4(config)#^Z R4# *Mar 1 00:34:09.207: %SYS-5-CONFIG_I: Configured from console by console R4# RACK15AS>1 [Resuming connection 1 to r1 ... ] R1#confi9  t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#access-list 1 per 224.20.73.1 15.128.20.0 R1(config)#int e 0/0 R1(config-if)#ip igmp j ? access-group IGMP group access group explicit-tracking Enable/Disable IGMP explicit-tracking helper-address IGMP helper address immediate-leave Leave groups immediately without sending last member query, use for one host network only join-group IGMP join multicast group last-member-query-count IGMP last member query count last-member-query-interval IGMP last member query interval limit IGMP limit mroute-proxy Mroute to IGMP proxy proxy-service Enable IGMP mroute proxy service querier-timeout IGMP previous querier timeout query-interval IGMP host query interval query-max-response-time IGMP max query response value static-group IGMP static multicast group unidirectional-link IGMP unidirectional link multicast routing v3lite Enable/disable IGMPv3 Lite version IGMP version R1(config-if)#ip igmp acc R1(config-if)#ip igmp access-group ? <1-99> Access list number WORD IP Named Standard Access list R1(config-if)#ip igmp access-group 1 ? R1(config-if)#ip igmp access-group 1 R1(config-if)#^Z R1# RACK15AS>5 [Resuming connection 5 to r5 ... ] 0 S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/1 S5(config-if)#iuop   p igmp jo S5(config-if)#ip igmp join-group 225.148.93.1 S5(config-if)#^Z S5# 01:14:30: %SYS-5-CONFIG_I: Configured from console by console S5# RACK15AS>1 [Resuming connection 1 to r1 ... ] *Ma R1#sh ip access Standard IP access list 1 10 permit 224.20.73.1, wildcard bits 15.128.20.0 (1 match) R1# R1# R1# R1# RACK15AS>5 [Resuming connection 5 to r5 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#int fa 0/1 S5(config-if)#int fa 0/1p igmp join-group 225.148.93.1          4.5.5.5 S5(config-if)#^Z S5# 01:15:41: %SYS-5-CONFIG_I: Configured from console by console S5# RACK15AS>65 % 65 is not an open connection RACK15AS>6 [Resuming connection 6 to r6 ... ] 0 S6#p 224..5  5.5.5 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.5.5.5, timeout is 2 seconds: Reply to request 0 from 17.57.100.2, 64 ms S6# S6# S6# RACK15AS>1 [Resuming connection 1 to r1 ... ] R1#sh run | b 0/0 interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip igmp access-group 1 half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 102 ! interface Ethernet0/1 --More--   ip address 17.100.1.1 255.255.255.0 ip pim sparse-dense-mode half-duplex no keepalive ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! ! access-list 1 permit 224.20.73.1 15.128.20.0 ! ! ! ! ! --More--   R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 0/09  R1(config-if)#ip ? Interface IP configuration subcommands: access-group Specify access control for packets accounting Enable IP accounting on this interface address Set the IP address of an interface authentication authentication subcommands bandwidth-percent Set EIGRP bandwidth limit bgp BGP interface commands broadcast-address Set the broadcast address of an interface cef Cisco Express Forwarding interface commands cgmp Enable/disable CGMP dhcp Configure DHCP parameters for this interface directed-broadcast Enable forwarding of directed broadcasts dvmrp DVMRP interface commands flow NetFlow related commands hello-interval Configures IP-EIGRP hello interval helper-address Specify a destination address for UDP broadcasts hold-time Configures IP-EIGRP hold time idle-group Specify interesting packets for idle-timer igmp IGMP interface commands information-reply Enable sending ICMP Information Reply messages irdp ICMP Router Discovery Protocol load-sharing Style of load sharing --More--   local-proxy-arp Enable local-proxy ARP mask-reply Enable sending ICMP Mask Reply messages mobile Mobile IP support mrm Configure IP Multicast Routing Monitor tester mroute-cache Enable switching cache for incoming multicast packets mtu Set IP Maximum Transmission Unit multicast IP multicast interface commands nat NAT interface commands nbar Network-Based Application Recognition next-hop-self Configures IP-EIGRP next-hop-self nhrp NHRP interface subcommands ospf OSPF interface commands pgm PGM Reliable Transport Protocol pim PIM interface commands policy Enable policy routing proxy-arp Enable proxy ARP rarp-server Enable RARP server for static arp entries redirects Enable sending ICMP Redirect messages rgmp Enable/disable RGMP rip Router Information Protocol route-cache Enable fast-switching cache for outgoing packets router IP router interface commands rsvp RSVP Interface Commands --More--   R1(config-if)#ip mu R1(config-if)#ip multicast ? boundary Boundary for administratively scoped multicast addresses helper-map Broadcast to Multicast map OR Multicast to ip-address map netflow NetFlow accounting for multicast rate-limit Rate limit multicast data packets tagswitch Enable IP Multicast Tagswitching ttl-threshold TTL threshold for multicast packets R1(config-if)#ip multicast rate-limit ? in Rate limit incoming packets out Rate limit outgoing packets R1(config-if)#ip multicast rate-limit in ? <0-4294967> Rate in kilobits per second group-list Rate limit for groups source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit in vi ? <0-4294967> Rate in kilobits per second R1(config-if)#ip multicast rate-limit in vi 8  0 ? R1(config-if)#ip multicast rate-limit in vi 80       gr R1(config-if)#ip multicast rate-limit in group-list ? <1-99> Multicast group access-list reference <1300-1999> Multicast group access-list reference (expanded range) WORD IP Named Standard Access list R1(config-if)#ip multicast rate-limit in group-list 2 ? <0-4294967> Rate in kilobits per second source-list Rate limit for sources video Rate limit video only whiteboard Rate limit whiteboard only R1(config-if)#ip multicast rate-limit in group-list 2 vi ? <0-4294967> Rate in kilobits per second R1(config-if)#ip multicast rate-limit in group-list 2 vi 80 R1(config-if)#exit R1(config)#access-; list 2 per 239.0.0.0 0.255.255.255.  R1(config)#ip sp R1(config)#ip sp a R1(config)#ip sap l R1(config)#ip sap li R1(config)#ip sap lis R1(config)#ip sap lis? % Unrecognized command R1(config)#ip sap lis          int fa 0    e 0/0 R1(config-if)#oi  ip sap l R1(config-if)#ip sap listen R1(config-if)#^Z R1#sh run *Mar 1 01:24:58.601: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b 0/0 interface Ethernet0/0 ip address 17.57.100.1 255.255.255.0 ip pim sparse-dense-mode ip multicast rate-limit in group-list 2 video 80 ip igmp access-group 1 ip sap listen half-duplex ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 180.40.7.34 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 103 ! interface Serial0/0.2 point-to-point ip address 180.40.7.66 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 102 --More--  ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim sparse-dense-mode half-duplex no keepalive ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip http server ip classless ! ! access-list 1 permit 224.20.73.1 15.128.20.0 access-list 2 permit 239.0.0.0 0.255.255.255 ! ! --More--   R1#con fi t % Ambiguous command: "con fi t" R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int e 01p sap listen nt e 01 /1 R1(config-if)#ip igmp q R1(config-if)#ip igmp quer? querier-timeout query-interval query-max-response-time R1(config-if)#ip igmp query R1(config-if)#ip igmp query-i R1(config-if)#ip igmp query-interval ? <1-18000> Query interval in seconds R1(config-if)#ip igmp query-interval 90 ? R1(config-if)#ip igmp query-interval 90 R1(config-if)#ip pim ? bidir-neighbor-filter PIM bidir capable peering filter bsr-border Border of PIM domain dense-mode Enable PIM dense-mode operation dr-priority PIM router DR priority nbma-mode Use Non-Broadcast Multi-Access (NBMA) mode on interface neighbor-filter PIM peering filter query-interval PIM router query interval sparse-dense-mode Enable PIM sparse-dense-mode operation sparse-mode Enable PIM sparse-mode operation state-refresh PIM DM State-Refresh configuration version PIM version R1(config-if)#ip pim        do sh ip pim int de Ethernet0/0 is up, line protocol is up Internet address is 17.57.100.1/24 Multicast switching: fast Multicast packets in/out: 1/33 Multicast boundary: not set Multicast TTL threshold: 0 PIM: enabled PIM version: 2, mode: sparse-dense PIM DR: 17.57.100.2 PIM neighbor count: 1 PIM Hello/Query interval: 30 seconds PIM State-Refresh processing: enabled PIM State-Refresh origination: disabled PIM NBMA mode: disabled PIM ATM multipoint signalling: disabled PIM domain border: disabled Multicast Tagswitching: disabled Ethernet0/1 is up, line protocol is up Internet address is 17.100.1.1/24 Multicast switching: fast Multicast packets in/out: 12/35 Multicast boundary: not set Multicast TTL threshold: 0 --More--   R1(config-if)#ip pim q R1(config-if)#ip pim query-interval 990  0 R1(config-if)#^Z R1#s *Mar 1 01:29:42.322: %SYS-5-CONFIG_I: Configured from console by console R1#sh run int e 0/1 Building configuration... Current configuration : 172 bytes ! interface Ethernet0/1 ip address 17.100.1.1 255.255.255.0 ip pim query-interval 90 ip pim sparse-dense-mode ip igmp query-interval 90 half-duplex no keepalive end R1# R1# RACK15AS>2 [Resuming connection 2 to r2 ... ] R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#do sh run | i send ip pim send-rp-discovery scope 3 R2(config)#nono    ip pim send-rp-discovery scope 3 ^ % Invalid input detected at '^' marker. R2(config)#noip pim send-rp-discovery scope 3no ip pim send-rp-discovery scope 3 R2(config)#ip pim ? accept-register Registers accept filter accept-rp RP accept filter autorp Configure AutoRP global operations bidir-enable Enable Bidir-PIM bsr-candidate Candidate bootstrap router (candidate BSR) log-neighbor-changes Log PIM neighbor up/down and DR changes register-rate-limit Rate limit for PIM data registers register-source Source address for PIM Register rp-address PIM RP-address (Rendezvous Point) rp-announce-filter Auto-RP announce message filter rp-candidate To be a PIMv2 RP candidate send-rp-announce Auto-RP send RP announcement send-rp-discovery Auto-RP send RP discovery message (as RP-mapping agent) spt-threshold Source-tree switching threshold ssm Configure Source Specific Multicast state-refresh PIM DM State-Refresh configuration vrf Select VPN Routing/Forwarding instance R2(config)#ip pim bs R2(config)#ip pim bsr-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R2(config)#ip pim bsr-candidate *Mar 1 01:30:05.604: %PIM-6-INVALID_RP_JOIN: Received (*, 224.2.127.254) Join from 0.0.0.0 for invalid RP 180.40.7.129 R2(config)#ip pim bsr-candidate fa 0/1 ? <0-32> Hash Mask length for RP selection R2(config)#ip pim bsr-candidate fa 0/1 R2(config)#^Z R2# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#do sh run | b send ip pim send-rp-announce FastEthernet0/1 scope 1 group-list 1 interval 5 ip pim register-rate-limit 2 ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! --More--   R3(config)#o no ip pim send-rp-announce FastEthernet0/1 scope 1 group-list 1 in$end-rp-announce FastEthernet0/1 scope 1 group-list 1 int erval 5 R3(config)#ip rp-ca R3(config)#ip rp-ca     pim rp-can R3(config)#ip pim rp-candidate ? Async Async interface BRI ISDN Basic Rate Interface BVI Bridge-Group Virtual Interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing R3(config)#ip pim rp-candidate fa 0/1 ? group-list group-list interval RP candidate advertisement interval priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 gr   R3(config)#ip pim rp-candidate fa 0/1 group-list 1 ? interval RP candidate advertisement interval priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 group-list 1 i  n 5 ? priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 group-list 1 in 5 R3(config)#^Z R3# *Mar 1 01:31:31.056: %SYS-5-CONFIG_I: Configured from console by console R3# RACK15AS>2 [Resuming connection 2 to r2 ... ] *M R2#sh ip pim rp map PIM Group-to-RP Mappings This system is the Bootstrap Router (v2) Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.3 (?), via bootstrap, priority 0, holdtime 17 Uptime: 00:00:10, expires: 00:00:16 R2# R2# R2# R2# RACK15AS>3 [Resuming connection 3 to r3 ... ] * R3#sh ip pim rp map PIM Group-to-RP Mappings This system is a candidate RP (v2) R3#sh ip pim rp map PIM Group-to-RP Mappings This system is a candidate RP (v2) Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:04, expires: 00:03:22 R3# R3# R3# R3#sh ip pim rp map PIM Group-to-RP Mappings This system is a candidate RP (v2) Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:00:08, expires: 00:03:18 R3#sh run | i rp-can ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 R3# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:01:03, expires: 00:03:23 R4# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:01:30, expires: 00:02:55 R7# RACK15AS> [Resuming connection 7 to r7 ... ] R7# R7#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.7.7.7), 00:03:17/00:02:13, RP 180.40.7.129, flags: SJPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 00:36:02/00:02:16, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:36:02/00:00:00 R7#^x2 % Unknown command or computer name, or unable to find computer address R7# R7# RACK15AS>2 [Resuming connection 2 to r2 ... ] R2#sh run | i bsr ip pim bsr-candidate FastEthernet0/1 0 R2# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b rp-can ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 ip pim register-rate-limit 2 ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! --More--   R3#confi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip pim ? accept-register Registers accept filter accept-rp RP accept filter autorp Configure AutoRP global operations bidir-enable Enable Bidir-PIM bsr-candidate Candidate bootstrap router (candidate BSR) log-neighbor-changes Log PIM neighbor up/down and DR changes register-rate-limit Rate limit for PIM data registers register-source Source address for PIM Register rp-address PIM RP-address (Rendezvous Point) rp-announce-filter Auto-RP announce message filter rp-candidate To be a PIMv2 RP candidate send-rp-announce Auto-RP send RP announcement send-rp-discovery Auto-RP send RP discovery message (as RP-mapping agent) spt-threshold Source-tree switching threshold ssm Configure Source Specific Multicast state-refresh PIM DM State-Refresh configuration vrf Select VPN Routing/Forwarding instance R3(config)#ip pim sp R3(config)#ip pim spt-threshold ? <0-4294967> Traffic rate in kilobits per second infinity Never switch to source-tree R3(config)#ip pim spt-threshold 1 R3(config)#^Z R3# *Mar 1 01:38:12.702: %SYS-5-CONFIG_I: Configured from console by console R3# RACK15AS>1 [Resuming connection 1 to r1 ... ] R1#ip pim spt-threshold 1 ^ % Invalid input detected at '^' marker. R1# R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pim spt-threshold 1 R1(config)#end R1# RACK15AS>2 [Resuming connection 2 to r2 ... ] R2# R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim spt-threshold 1 R2(config)#end R2# RACK15AS>4 [Resuming connection 4 to r4 ... ] R4# R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#ip pim spt-threshold 1 R4(config)#end R4# RACK15AS>5 [Resuming connection 5 to r5 ... ] S5# S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)#ip pim spt-threshold 1 S5(config)#end S5# RACK15AS>6 [Resuming connection 6 to r6 ... ] S6# S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim spt-threshold 1 S6(config)#end S6# 01:42:52: %SYS-5-CONFIG_I: Configured from console by console^x7 % Unknown command or computer name, or unable to find computer address S6# S6# S6#config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim spt-threshold 1 S6(config)#end S6# 01:42:57: %SYS-5-CONFIG_I: Configured from console by console RACK15AS>77 % 77 is not an open connection RACK15AS>77  [Resuming connection 7 to r7 ... ] R7#config t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip pim spt-threshold 1 R7(config)#end R7#^Z R7# *Mar 1 01:39:56.621: %SYS-5-CONFIG_I: Configured from console by console R7#confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip pim > ? accept-register Registers accept filter accept-rp RP accept filter autorp Configure AutoRP global operations bidir-enable Enable Bidir-PIM bsr-candidate Candidate bootstrap router (candidate BSR) log-neighbor-changes Log PIM neighbor up/down and DR changes register-rate-limit Rate limit for PIM data registers register-source Source address for PIM Register rp-address PIM RP-address (Rendezvous Point) rp-announce-filter Auto-RP announce message filter rp-candidate To be a PIMv2 RP candidate send-rp-announce Auto-RP send RP announcement send-rp-discovery Auto-RP send RP discovery message (as RP-mapping agent) spt-threshold Source-tree switching threshold ssm Configure Source Specific Multicast state-refresh PIM DM State-Refresh configuration vrf Select VPN Routing/Forwarding instance R7(config)#ip pim bidir-enable R7(config)#^Z R7# RACK15AS>1 [Resuming connection 1 to r1 ... ] *M R1#config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#ip pim bidir-enable R1(config)# R1(config)#end R1# R1# *Mar 1 01:44:50.291: %SYS-5-CONFIG_I: Configured from console by console R1# RACK15AS>2 [Resuming connection 2 to r2 ... ] * R2#config t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#ip pim bidir-enable R2(config)# R2(config)#end R2# R2# *Mar 1 01:43:50. RACK15AS>4 [Resuming connection 4 to r4 ... ] *M R4#config t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#ip pim bidir-enable R4(config)# R4(config)#end R4# R4# RACK15AS>5 [Resuming connection 5 to r5 ... ] 0 S5#config t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#ip pim bidir-enable S5(config)# S5(config)#end S5# S5# 01:47:02: %SYS-5-CONFIG_I: Configured from console by console S5# RACK15AS>7 6 [Resuming connection 6 to r6 ... ] config t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#ip pim bidir-enable S6(config)# S6(config)#end S6# S6# 01:47:06: %SYS-5-CONFIG_I: Configured from console by console RACK15AS>3 [Resuming connection 3 to r3 ... ] R3#c config t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#ip pim bidir-enable R3(config)# R3(config)# RACK15AS>7 [Resuming connection 7 to r7 ... ] *M R7#sh ip    run |  b bid ip pim bidir-enable ip pim spt-threshold 1 ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! ! end R7#q sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.7.7.7), 00:01:43/00:01:56, RP 180.40.7.129, flags: SPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 00:45:25/00:01:51, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:45:25/00:00:00 R7#pi 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 120 ms R7#pi 224.4.4.4sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:03/stopped, RP 180.40.7.129, flags: SPF Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (17.100.1.2, 224.4.4.4), 00:00:03/00:02:57, flags: PFT Incoming interface: FastEthernet0/1, RPF nbr 0.0.0.0, Registering Outgoing interface list: Null (*, 224.7.7.7), 00:01:57/00:01:42, RP 180.40.7.129, flags: SPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 00:45:40/00:01:36, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:45:40/00:00:00 R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:12:48, expires: 00:02:42 R7# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3(config)#ip pim bidir-enablespt-threshold 1rp-candidate fa 0/1 group-list 1 in 5 ? bidir Group range treated in bidirectional shared-tree mode priority RP candidate priority R3(config)#ip pim rp-candidate fa 0/1 group-list 1 in 5 bi R3(config)#ip pim rp-candidate fa 0/1 group-list 1 in 5 bidir R3(config)# RACK15AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 180.40.7.129 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 210 Uptime: 00:13:10, expires: 00:03:19 R7#sh ip pim rp mapmroute pi 224.4.4.4sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.7.7.7), 00:00:12/00:02:47, RP 180.40.7.129, flags: BPL Bidir-Upstream: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 00:00:12/00:00:00 (*, 224.0.1.40), 00:46:22/00:02:47, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:46:22/00:00:00 R7#sh ip mroutepim rp mapmroute pi 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 108 ms Reply to request 0 from 180.40.7.130, 124 ms R7#pi 224.4.4.4sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:00:04/00:02:57, RP 180.40.7.129, flags: BP Bidir-Upstream: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 00:00:04/00:00:00 (*, 224.7.7.7), 00:00:30/00:02:29, RP 180.40.7.129, flags: BPL Bidir-Upstream: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 00:00:31/00:00:00 (*, 224.0.1.40), 00:46:41/00:02:28, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 00:46:41/00:00:00 R7# RACK15AS>3 [Resuming connection 3 to r3 ... ] R3(config)# R3(config)#^Z R3#sh run | b *Mar 1 01:47:02.459: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | b     i rp-can ip pim rp-candidate FastEthernet0/1 group-list 1 interval 5 bidir R3# RACK15AS>4 [Resuming connection 4 to r4 ... ] *M R4#sh ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.4.4.4), 00:01:47/00:01:52, RP 180.40.7.129, flags: BPL Bidir-Upstream: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: FastEthernet0/0, Bidir-Upstream/Dense, 00:01:47/00:00:00 (*, 224.0.1.40), 01:11:57/00:02:54, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/0, Forward/Dense, 01:11:46/00:00:00 (*, 224.44.44.44), 00:01:48/00:02:48, RP 180.40.7.129, flags: BCL Bidir-Upstream: FastEthernet0/0, RPF nbr 180.40.7.129 Outgoing interface list: Loopback0, Forward/Dense, 00:01:48/00:02:48 FastEthernet0/0, Bidir-Upstream/Dense, 00:01:48/00:00:00 R4# [Connection to r4 closed by foreign host] RACK15AS>