=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2007.03.13 10:55:57 =~=~=~=~=~=~=~=~=~=~=~= confi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)#ip sp R7(config)#ip sp  pim R7(config)#ip pim sp R7(config)#ip pim spt-threshold ? <0-4294967> Traffic rate in kilobits per second infinity Never switch to source-tree R7(config)#ip pim spt-threshold 1 R7(config)#^Z R7# *Mar 1 19:31:03.445: %SYS-5-CONFIG_I: Configured from console by console R7# RACK1AS>1 [Resuming connection 1 to r1 ... ] [OK] R1# R1#confi t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# R1(config)#ip pim spt-threshold 1 R1(config)#^Z R1# RACK1AS>2 [Resuming connection 2 to r4 ... ] [OK] R2# R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)#ip pim spt-threshold 1 R2(config)#^Z R2# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar 13 03:5 R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#ip pim spt-threshold 1 R3(config)#^Z R3# RACK1AS>4 [Resuming connection 4 to r2 ... ] [OK] R4# R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#ip pim spt-threshold 1 R4(config)#^Z R4# RACK1AS>5 [Resuming connection 5 to s1 ... ] S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#ip pim spt-threshold 1 S5(config)#^Z S5# RACK1AS>6 [Resuming connection 6 to s2 ... ] S6#confi t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip igmp jo 224.20.68.1~~~~~~~~~~~~~~~~                                       S6(config)#ip pim spt-threshold 1 S6(config)#^Z S6# 19:42:51: %SYS-5-CONFIG_I: Configured from console by console S6# S6# S6#conf t Enter configuration commands, one per line. End with CNTL/Z. S6(config)#ip pim S6(config)#ip pim bi S6(config)#ip pim bidir-enable ? S6(config)#ip pim bidir-enable S6(config)#^Z S6# RACK1AS>1 [Resuming connection 1 to r1 ... ] *Mar 1 19:31:47.305: R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip pim bidir-enable R1(config)#^Z R1# RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 18:06 R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)# R2(config)# R2(config)# R2(config)#ip pim bidir-enable R2(config)# R2(config)# R2(config)#^Z R2# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar 13 18:06:5 R3# R3#ip pim bidir-enable ^ % Invalid input detected at '^' marker. R3# R3# R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)# R3(config)#ip pim bidir-enable R3(config)# R3(config)# R3(config)# RACK1AS>4 [Resuming connection 4 to r2 ... ] *Mar 1 19:31:58. R4#conf t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# R4(config)#ip pim bidir-enable R4(config)# R4(config)# R4(config)# RACK1AS>5 [Resuming connection 5 to s1 ... ] 19:42:36: %SYS- S5#confi t Enter configuration commands, one per line. End with CNTL/Z. S5(config)# S5(config)#ip pim bidir-enable S5(config)# S5(config)# S5(config)# RACK1AS>6 [Resuming connection 6 to s2 ... ] 19:43:55: %SYS-5-CONF S6#conf t Enter configuration commands, one per line. End with CNTL/Z. S6(config)# S6(config)#ip pim bidir-enable S6(config)# S6(config)# S6(config)# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7#co  nfi t Enter configuration commands, one per line. End with CNTL/Z. R7(config)# R7(config)#ip pim bidir-enable R7(config)# R7(config)# R7(config)#do sh ip mr IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 239.148.93.1), 00:00:05/00:02:54, RP 3.3.3.3, flags: SPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 14:46:35/00:02:54, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 14:46:35/00:00:00 R7(config)# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3(config)#ip pim bidir-enablespt-threshold 1bidir-enable  do sh run | i rp-can ip pim rp-candidate Loopback0 group-list 1 interval 5 R3(config)#ip pim rp-candidate Loopback0 group-list 1 interval 5 ? bidir Group range treated in bidirectional shared-tree mode priority RP candidate priority R3(config)#ip pim rp-candidate Loopback0 group-list 1 interval 5 bidir ? R3(config)#ip pim rp-candidate Loopback0 group-list 1 interval 5 bidir R3(config)# RACK1AS>7 [Resuming connection 7 to r7 ... ] do sh ip mr IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 239.148.93.1), 00:00:02/00:02:57, RP 3.3.3.3, flags: BPL Bidir-Upstream: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: FastEthernet0/1, Bidir-Upstream/Sparse-Dense, 00:00:02/00:00:00 (*, 224.0.1.40), 14:47:51/00:02:57, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 14:47:51/00:00:00 R7(config)#q ^Z R7#sh ip p *Mar 1 19:35:40.311: %SYS-5-CONFIG_I: Configured from console by console R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 3.3.3.3 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 150 Uptime: 14:16:16, expires: 00:02:14 R7# R7# R7# R7# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3(config)#^Z R3#sh run *Mar 13 18:11:46.143: %SYS-5-CONFIG_I: Configured from console by console R3#sh run | i rp-can ip pim rp-candidate Loopback0 group-list 1 interval 5 bidir R3# RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 18:08:51.39 R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip dhcp pool test R2(dhcp-config)#net 180.40.7.96 ? % Ambiguous command: "net 180.40.7.96 " R2(dhcp-config)#net 180.40.7.96 w 180.40.7.96  180.40.7.96 ? /nn or A.B.C.D Network mask or prefix length R2(dhcp-config)#netw 180.40.7.96 /27 R2(dhcp-config)# RACK1AS>6 [Resuming connection 6 to s2 ... ] S6(config)#int fa 0/4 S6(config-if)#do sh run int fa 0/4 Building configuration... Current configuration : 176 bytes ! interface FastEthernet0/4 no switchport ip address 180.40.7.97 255.255.255.224 ip pim sparse-dense-mode ip igmp join-group 224.6.6.6 ip igmp join-group 224.20.68.1 end S6(config-if)#ip add dhcp S6(config-if)# 20:04:56: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/4 from FULL to DOWN, Neighbor Down: Interface down or detached S6(config-if)# S6(config-if)# S6(config-if)#dol    Interface FastEthernet0/4 assigned DHCP address 180.40.7.97, mask 255.255.255.224 deb dhcp DHCP client activity debugging is on S6(config-if)# 20:05:11: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/4 from LOADING to FULL, Loading Done S6(config-if)# S6(config-if)# S6(config-if)#shut 20:05:19: DHCP: SRelease attempt # 1 for entry: 20:05:19: DHCP: SRelease placed Server ID option: 180.40.7.98 20:05:19: DHCP: SRelease: 279 bytes 20:05:19: DHCP: SRelease attempt # 2 for entry: 20:05:19: DHCP: SRelease placed Server ID option: 180.40.7.98 20:05:19: DHCP: SRelease: 279 bytes 20:05:20: DHCP: SRelease attempt # 3 for entry: 20:05:20: DHCP: SRelease placed Server ID option: 180.40.7.98 20:05:20: DHCP: SRelease: 279 bytes S6(config-if)# 20:05:21: RAC: DHCP stopped on interface FastEthernet0/4 S6(config-if)# S6(config-if)# S6(config-if)# 20:05:21: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/4 from FULL to DOWN, Neighbor Down: Interface down or detached 20:05:23: %LINK-5-CHANGED: Interface FastEthernet0/4, changed state to administratively down 20:05:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to down S6(config-if)# S6(config-if)# S6(config-if)#no shut S6(config-if)# 20:05:29: DHCP: DHCP client process started: 10 20:05:29: RAC: Delaying starting DHCP because interface FastEthernet0/4 not up 20:05:29: DHCP: DHCP client process started: 10 20:05:29: RAC: Delaying starting DHCP because interface FastEthernet0/4 not up 20:05:31: %LINK-3-UPDOWN: Interface FastEthernet0/4, changed state to up 20:05:31: DHCP: DHCP client process started: 10 20:05:31: RAC: Starting DHCP discover on FastEthernet0/4 20:05:31: DHCP: Try 1 to acquire address for FastEthernet0/4 20:05:31: DHCP: allocate request 20:05:31: DHCP: zapping entry in DHC_PURGING state for Fa0/4 20:05:31: DHCP: new entry. add to queue 20:05:31: DHCP: SDiscover attempt # 1 for entry: 20:05:31: DHCP: SDiscover: sending 294 byte length DHCP packet 20:05:31: DHCP: SDiscover 294 bytes 20:05:31: B'cast on FastEthernet0/4 interface from 0.0.0.0 20:05:32: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up 20:05:33: DHCP: Received a BOOTREP pkt 20:05:33: DHCP: offer received from 180.40.7.98 20:05:33: DHCP: SRequest attempt # 1 for entry: 20:05:33: DHCP: SRequest- Server ID option: 180.40.7.98 20:05:33: DHCP: SRequest- Requested IP addr option: 180.40.7.99 20:05:33: DHCP: SRequest placed lease len option: 86400 20:05:33: DHCP: SRequest: 312 bytes 20:05:33: DHCP: SRequest: 312 bytes 20:05:33: B'cast on FastEthernet0/4 interface from 0.0.0.0 20:05:33: DHCP: Received a BOOTREP pktInterface FastEthernet0/4 assigned DHCP address 180.40.7.99, mask 255.255.255.224 20:05:36: DHCP Client Pooling: ***Allocated IP address: 180.40.7.99 20:05:36: Allocated IP address = 180.40.7.99 255.255.255.224 20:05:51: DHCP: deleting entry 2168868 0.0.0.0 from list S6(config-if)#do u al 20:06:16: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/4 from LOADING to FULL, Loading Donel All possible debugging has been turned off S6(config-if)#do deb dhcp det DHCP client activity debugging is on (detailed) S6(config-if)#no ip add 20:06:32: DHCP: SRelease attempt # 1 for entry: 20:06:32: Temp IP addr: 180.40.7.99 for peer on Interface: FastEthernet0/4 20:06:32: Temp sub net mask: 255.255.255.224 20:06:32: DHCP Lease server: 180.40.7.98, state: 7 Releasing 20:06:32: DHCP transaction id: 19D7 20:06:32: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs 20:06:32: Next timer fires after: 00:00:01 20:06:32: Retry count: 1 Client-ID: cisco-0012.7f58.1300-Fa0/4 20:06:32: Hostname: S6 20:06:32: DHCP: SRelease placed Server ID option: 180.40.7.98 20:06:32: DHCP: SRelease: 279 bytes 20:06:32: DHCP: SRelease attempt # 2 for entry: 20:06:32: Temp IP addr: 180.40.7.99 for peer on Interface: FastEthernet0/4 20:06:32: Temp sub net mask: 255.255.255.224 20:06:32: DHCP Lease server: 180.40.7.98, state: 7 Releasing 20:06:32: DHCP transaction id: 19D7 20:06:32: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs 20:06:32: Next timer fires after: 00:00:00 20:06:32: Retry count: S6(config-if)# 2 Client-ID: cisco-0012.7f58.1300-Fa0/4 20:06:32: Hostname: S6 20:06:32: DHCP: SRelease placed Server ID option: 180.40.7.98 20:06:32: DHCP: SRelease: 279 bytes 20:06:32: DHCP: Releasing ipl options: 20:06:33: DHCP: SRelease attempt # 3 for entry: 20:06:33: Temp IP addr: 180.40.7.99 for peer on Interface: FastEthernet0/4 20:06:33: Temp sub net mask: 255.255.255.224 20:06:33: DHCP Lease server: 180.40.7.98, state: 7 Releasing 20:06:33: DHCP transaction id: 19D7 20:06:33: Lease: 86 S6(config-if)#400 secs, Renewal: 43200 secs, Rebind: 75600 secs 20:06:33: Next timer fires after: 00:00:01 20:06:33: Retry count: 3 Client-ID: cisco-0012.7f58.1300-Fa0/4 20:06:33: Hostname: S6 20:06:33: DHCP: SRelease placed Server ID option: 180.40.7.98 20:06:33: DHCP: SRelease: 279 bytes 20:06:34: RAC: DHCP stopped on interface FastEthernet0/4 20:06:34: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/4 from FULL to DOWN, Neighbor Down: Interface down or detachedip add dhcp S6(config-if)# 20:06:38: DHCP: DHCP client process started: 10 20:06:38: RAC: Starting DHCP discover on FastEthernet0/4 20:06:38: DHCP: Try 1 to acquire address for FastEthernet0/4 20:06:38: DHCP: allocate request 20:06:38: DHCP: zapping entry in DHC_PURGING state for Fa0/4 20:06:38: DHCP: new entry. add to queue 20:06:38: DHCP: SDiscover attempt # 1 for entry: 20:06:38: Temp IP addr: 0.0.0.0 for peer on Interface: FastEthernet0/4 20:06:38: Temp sub net mask: 0.0.0.0 20:06:38: DHCP Lease server: 0.0.0.0, state: 1 Selecting 20:06:38: DHCP transaction id: A1E 20:06:38: Lease: 0 secs, Renewal: 0 secs, Rebind: 0 secs 20:06:38: Next timer fires after: 00:00:03 20:06:38: Retry count: 1 Client-ID: cisco-0012.7f58.1300-Fa0/4 20:06:38: Hostname: S6 20:06:38: DHCP: SDiscover: sending 294 byte length DHCP packet 20:06:38: DHCP: SDiscover 294 bytes 20:06:38: B'cast on FastEthernet0/4 interface from 0.0.0.0 20:06:40: DHCP: Received a BOOTREP pkt 20:06:40: DHCP: Scan: Message type: DHCP Offer 20:06:40: DHCP: Scan: Server ID Option: 180.40.7.98 = B4280762 20:06:40: DHCP: Scan: Lease Time: 86400 20:06:40: DHCP: Scan: Renewal time: 43200 20:06:40: DHCP: Scan: Rebind time: 75600 20:06:40: DHCP: Scan: Subnet Address Option: 255.255.255.224 20:06:40: DHCP: rcvd pkt source: 180.40.7.98, destination: 255.255.255.255 20:06:40: UDP sport: 43, dport: 44, length: 308 20:06:40: DHCP op: 2, htype: 1, hlen: 6, hops: 0 20:06:40: DHCP server identifier: 180.40.7.98 20:06:40: xid: A1E, secs: 0, flags: 8000 20:06:40: client: 0.0.0.0, your: 180.40.7.100 20:06:40: srvr: 0.0.0.0, gw: 0.0.0.0 20:06:40: options block length: 60 20:06:40: DHCP Offer Message Offered Address: 180.40.7.100 20:06:40: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 20:06:40: DHCP: Server ID Option: 180.40.7.98 20:06:40: DHCP: offer received from 180.40.7.98 20:06:40: DHCP: SRequest attempt # 1 for entry: 20:06:40: Temp IP addr: 180.40.7.100 for peer on Interface: FastEthernet0/4 20:06:40: Temp sub net mask: 255.255.255.224 20:06:40: DHCP Lease server: 180.40.7.98, state: 2 Requesting 20:06:40: DHCP transaction id: A1E 20:06:40: Lease: 86400 secs, Renewal: 0 secs, Rebind: 0 secs 20:06:40: Next timer fires after: 00:00:02 20:06:40: Retry count: 1 Client-ID: cisco-0012.7f58.1300-Fa0/4 20:06:40: Hostname: S6 20:06:40: DHCP: SRequesInterface FastEthernet0/4 assigned DHCP address 180.40.7.100, mask 255.255.255.224 t- Server ID option: 180.40.7.98 20:06:40: DHCP: SRequest- Requested IP addr option: 180.40.7.100 20:06:40: DHCP: SRequest placed lease len option: 86400 20:06:40: DHCP: SRequest: 312 bytes 20:06:40: DHCP: SRequest: 312 bytes 20:06:40: B'cast on FastEthernet0/4 interface from 0.0.0.0 20:06:40: DHCP: Received a BOOTREP pkt 20:06:40: DHCP: Scan: Message type: DHCP Ack 20:06:40: DHCP: Scan: Server ID Option: 180.40.7.98 = B4280762 20:06:40: DHCP: Scan: Lease Time: 86400 20:06:40: DHCP: Scan: Renewal time: 43200 20:06:40: DHCP: Scan: Rebind time: 75600 20:06:40: DHCP: Scan: Host Name: S6 20:06:40: DHCP: Scan: Subnet Address Option: 255.255.255.224 20:06:40: DHCP: rcvd pkt source: 180.40.7.98, destination: 255.255.255.255 20:06:40: UDP sport: 43, dport: 44, length: 308 20:06:40: DHCP op: 2, htype: 1, hlen: 6, hops: 0 20:06:40: DHCP server identifier: 180.40.7.98 20:06:40: xid: A1E, secs: 0, flags: 8000 20:06:40: client: 0.0.0.0, your: 180.40.7.100 20:06:40: srvr: 0.0.0.0, gw: 0.0.0.0 20:06:40: options block length: 60 20:06:40: DHCP Ack Message 20:06:40: DHCP: Lease Seconds: 86400 Renewal secs: 43200 Rebind secs: 75600 20:06:40: DHCP: Server ID Option: 180.40.7.98 20:06:40: DHCP Host Name Option: S6 20:06:43: DHCP: Releasing ipl options: 20:06:43: DHCP: Applying DHCP options: 20:06:43: DHCP Client Pooling: ***Allocated IP address: 180.40.7.100 20:06:43: Allocated IP address = 180.40.7.100 255.255.255.224 20:07:04: DHCP: QScan: Purging entry 20:07:04: DHCP: deleting entry 20A8C80 0.0.0.0 from list 20:07:04: Temp IP addr: 0.0.0.0 for peer on Interface: unknown 20:07:04: Temp sub net mask: 255.255.255.224 20:07:04: DHCP Lease server: 180.40.7.98, state: 8 Purging 20:07:04: DHCP transaction id: 19D7 20:07:04: Lease: 86400 secs, Renewal: 43200 secs, Rebind: 75600 secs 20:07:04: No timer running 20:07:04: Retry count: 0 Client-ID: 20:07:04: Hostname: S6do uy all uy all ^ % Invalid input detected at '^' marker. S6(config-if)#do u all All possible debugging has been turned off S6(config-if)# RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 18:29:25. R2(dhcp-config)# *Mar 13 18:31:57.523: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.97 on FastEthernet0/1 from LOADING to FULL, Loading Done R2(dhcp-config)#do sh ip dhcp bi % Ambiguous command: "do sh ip dhcp bi" R2(config)# *Mar 13 18:32:20.511: %PIM-5-NBRCHG: neighbor 180.40.7.99 DOWN on interface FastEthernet0/1 non DR R2(config)#do sh ip dhcp bin Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 180.40.7.100 0063.6973.636f.2d30. Mar 14 2007 06:31 PM Automatic 3031.322e.3766.3538. 2e31.3330.302d.4661. 302f.34 R2(config)# *Mar 13 18:32:52.399: %PIM-5-NBRCHG: neighbor 0.0.0.0 DOWN on interface FastEthernet0/1 non DR R2(config)#no ip djhcp pool hcp pool hcp pool test R2(config)#ip dhcp pool S6 R2(dhcp-config)#clie R2(dhcp-config)#client-i R2(dhcp-config)#client-identifier ^ % Invalid input detected at '^' marker. R2(dhcp-config)#R2(dhcp-config)# ^ % Invalid input detected at '^' marker. R2(dhcp-config)#R2(dhcp-config)# R2(dhcp-config)#client-identifier 0063.6973.636f.2d30.3031.322e.3766.3538.2e3$tifier 0063.6973.636f.2d30.3031.322e.3766.3538.2e31 .3330.3023.6973.636f.2d30.3031.322e.3766.3538.2e31.3330.302d .4661.302f.2d30.3031.322e.3766.3538.2e31.3330.302d.4661.302f .34 R2(dhcp-config)#hoi  ost R2(dhcp-config)#host ? A.B.C.D IP address in dotted-decimal notation R2(dhcp-config)#host 180.40.7.97 /27 R2(dhcp-config)# RACK1AS>6 [Resuming connection 6 to s2 ... ] 20:07:28: %OSP S6(config-if)# ip address 180.40.7.97 255.255.255.224 S6(config-if)# 20:13:23: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on FastEthernet0/4 from FULL to DOWN, Neighbor Down: Interface down or detached S6(config-if)# S6(config-if)# S6(config-if)#^Z S6# RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 18:37:53.226 R2(dhcp-config)# R2(dhcp-config)#exit R2(config)#int fa 0/1 R2(config-if)#ip m,u  u R2(config-if)#ip multicast h R2(config-if)#ip multicast helper-map ? A.B.C.D IP multicast address broadcast Broadcast address R2(config-if)#ip multicast helper-map *Mar 13 18:38:32.522: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.97 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Dead timer expired *Mar 13 18:38:33.230: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.97 on FastEthernet0/1 from LOADING to FULL, Loading Done R2(config-if)#ip multicast helper-map br R2(config-if)#ip multicast helper-map broadcast ? A.B.C.D IP address R2(config-if)#ip multicast helper-map broadcast 246  26.6.6.6 ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R2(config-if)#ip multicast helper-map broadcast 226.6.6.6                                             e *Mar 13 18:39:21.534: %PIM-5-NBRCHG: neighbor 180.40.7.100 DOWN on interface FastEthernet0/1 DR *Mar 13 18:39:21.534: %PIM-5-DRCHG: DR change from neighbor 180.40.7.100 to 180.40.7.98 on interface FastEthernet0/1 R2(config-if)#exit R2(config)#ip access R2(config)#ip access-list Prob13eProb13xProb13 Prob13Prob13 R2(config-ext-nacl)#per udp host 180.40.7.97 host 255.255.255.2555  eq tftp R2(config-ext-nacl)#int fa 0/1 R2(config-if)#ip mu R2(config-if)#ip multicast h R2(config-if)#ip multicast helper-map b R2(config-if)#ip multicast helper-map broadcast 226.6.6.6 ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R2(config-if)#ip multicast helper-map broadcast 226.6.6.6 Prob13 ? ttl TTL re-mapping R2(config-if)#ip multicast helper-map broadcast 226.6.6.6 Prob13 R2(config-if)# RACK1AS>1 [Resuming connection 1 to r1 ... ] *Mar 1 19:33:3 R1#sh ip io  int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 17.57.100.1 YES manual up up Serial0/0 unassigned YES manual up up Serial0/0.1 180.40.7.34 YES manual administratively down down Serial0/0.2 180.40.7.66 YES manual up up FastEthernet0/1 17.100.1.1 YES manual up up Serial0/1 unassigned YES manual administratively down down R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ip access R1(config)#ip access-list ex Prob13 R1(config-ext-nacl)#per udp host 180.40.7.97 host 226.6.6.6 eq tftp R1(config-ext-nacl)#int s 0/0.2 R1(config-subif)#ip mu R1(config-subif)#ip multicast h R1(config-subif)#ip multicast helper-map ? A.B.C.D IP multicast address broadcast Broadcast address R1(config-subif)#ip multicast helper-map 226.6.6.6 ? A.B.C.D IP address R1(config-subif)#ip multicast helper-map 226.6.6.6 17.100.1.255 ? <100-199> access-list <2000-2699> access-list (expanded range) WORD IP Named Extended Access list R1(config-subif)#ip multicast helper-map 226.6.6.6 17.100.1.255 Prob134    ? ttl TTL re-mapping R1(config-subif)#ip multicast helper-map 226.6.6.6 17.100.1.255 Prob13 R1(config-subif)# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7#deb ip pack det IP packet debugging is on (detailed) R7# *Mar 1 20:10:49.096: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 20:10:50.842: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 R7# *Mar 1 20:10:52.433: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 56, rcvd 0, proto=103 R7# RACK1AS>6 [Resuming connection 6 to s2 ... ] 20:13:29: %SYS-5-CONF S6#copy tftp rt  run Address or name of remote host []? 255.255.255.255 Source filename []? test Destination filename [running-config]? Accessing tftp://255.255.255.255/test... RACK1AS>7 [Resuming connection 7 to r7 ... ] *Mar 1 20:10:55. R7# R7# *Mar 1 20:11:25.599: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# *Mar 1 20:11:29.101: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 20:11:35.600: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# *Mar 1 20:11:39.102: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 20:11:45.600: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# *Mar 1 20:11:49.102: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 20:11:50.664: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 58, sending broad/multicast, proto=103 R7# *Mar 1 20:11:52.447: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.13, len 56, rcvd 0, proto=103 R7# *Mar 1 20:11:55.601: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7# *Mar 1 20:11:57.215: IP: s=17.100.1.2 (local), d=224.0.0.13 (FastEthernet0/1), len 54, sending broad/multicast, proto=103 R7# RACK1AS>1 [Resuming connection 1 to r1 ... ] R1(config-subif)#sh    do sh ip int fa 0/1 FastEthernet0/1 is up, line protocol is up Internet address is 17.100.1.1/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Multicast reserved groups joined: 224.0.0.5 224.0.0.6 224.0.0.1 224.0.0.2 224.0.0.22 224.0.0.13 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF Fast switching turbo vector --More--   R1(config-subif)#int fa 0/1 R1(config-if)#ip di R1(config-if)#ip directed-broadcast R1(config-if)# RACK1AS>6 [Resuming connection 6 to s2 ... ] %Error opening S6#test255.255.255.255copy tftp run  Address or name of remote host [255.255.255.255]? Source filename [test]? Destination filename [running-config]? Accessing tftp://255.255.255.255/test... RACK1AS>7 [Resuming connection 7 to r7 ... ] *Mar 1 20:11:59.113: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 41, rcvd 2 *Mar 1 20:12:37.413: UDP src=55153, dst=69 R7# R7# *Mar 1 20:12:39.104: IP: s=17.100.1.2 (local), d=224.0.0.5 (FastEthernet0/1), len 80, sending broad/multicast, proto=89 R7# *Mar 1 20:12:41.099: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.1, len 28, rcvd 0, proto=2 *Mar 1 20:12:41.416: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 41, rcvd 2 *Mar 1 20:12:41.416: UDP src=55153, dst=69 R7# *Mar 1 20:12:45.094: IP: s=17.100.1.2 (local), d=239.148.93.1 (FastEthernet0/1), len 28, sending broad/multicast, proto=2 *Mar 1 20:12:45.599: IP: s=17.100.1.1 (FastEthernet0/1), d=224.0.0.5, len 80, rcvd 0, proto=89 R7#u a *Mar 1 20:12:46.416: IP: s=180.40.7.97 (FastEthernet0/1), d=255.255.255.255, len 41, rcvd 2 *Mar 1 20:12:46.416: UDP src=55153, dst=69 R7#u all All possible debugging has been turned off R7# RACK1AS>2 [Resuming connection 2 to r4 ... ] R2(config-if)#^Z R2# RACK1AS>21 % 21 is not an open connection RACK1AS> RACK1AS>1 [Resuming connection 1 to r1 ... ] R1(config-if)# R1(config-if)#^Z R1# *Mar 1 20:18:28.973: %SYS-5-CONFIG_I: Configured from console by console R1#sh run | b 0/1 interface FastEthernet0/1 ip address 17.100.1.1 255.255.255.0 ip directed-broadcast ip pim query-interval 90 ip pim sparse-dense-mode ip igmp query-interval 90 speed auto half-duplex no keepalive ! interface Serial0/1 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ! ! no ip http server no ip http secure-server ip pim bidir-enable --More--  ip pim spt-threshold 1 ! ip access-list extended Prob13 permit udp host 180.40.7.97 host 226.6.6.6 eq tftp ! access-list 1 permit 224.20.73.1 15.128.20.0 access-list 2 permit 239.0.0.0 0.255.255.255 ! ! ! control-plane ! ! ! ! ! ! dial-peer cor custom ! ! ! ! ! --More-- RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 18:53:25.566: R2#sh run | b dhcp no ip dhcp use vrf connected ! ip dhcp pool S6 host 180.40.7.97 255.255.255.224 client-identifier 0063.6973.636f.2d30.3031.322e.3766.3538.2e31.3330.302d.4661.302f.34 ! ! no ip domain lookup ip multicast-routing ! ! voice-card 0 no dspfarm ! ! ! ! ! ! ! ! ! --More--  ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 226.6.6.6 Prob13 duplex auto speed auto --More--  ! --More--  interface Serial0/0/0 --More--   no ip address --More--   encapsulation frame-relay --More--   no fair-queue --More--  ! interface Serial0/0/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 203 ! interface Serial0/0/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 201 ! interface Serial0/0/1 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode ! interface Serial0/1/0 no ip address shutdown ! interface Serial0/1/1 no ip address --More--   shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ! ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ! ip access-list extended Prob13 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! control-plane ! --More-- RACK1AS>4 [Resuming connection 4 to r2 ... ] R4(config)#int fa 0/0 R4(config-if)#ip pim sp R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)#^Z R4# RACK1AS>2 [Resuming connection 2 to r4 ... ]  ! --More--   R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int lo 0 R2(config-if)#ip a *Mar 13 18:57:06.526: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up R2(config-if)#ip add 2.2.2.2 255.2555. ~  .255.2 0 R2(config-if)#exit R2(config)#ip ms R2(config)#ip msdp pee R2(config)#ip msdp peer ? Hostname or A.B.C.D Peer name or address R2(config)#ip msdp peer 3.3.3.3 ? connect-source Configure source address used for MSDP connection remote-as Configured AS number R2(config)#ip msdp peer 3.3.3.3 co R2(config)#ip msdp peer 3.3.3.3 connect-source ? Async Async interface BVI Bridge-Group Virtual Interface CDMA-Ix CDMA Ix interface CTunnel CTunnel interface Dialer Dialer interface FastEthernet FastEthernet IEEE 802.3 Lex Lex interface Loopback Loopback interface MFR Multilink Frame Relay bundle interface Multilink Multilink-group interface Null Null interface Port-channel Ethernet Channel of interfaces Serial Serial Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-PPP Virtual PPP interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing XTagATM Extended Tag ATM interface R2(config)#ip msdp peer 3.3.3.3 connect-source lo 0 R2(config)#ip msdp peer 3.3.3.3 connect-source lo 0 ? remote-as Configured AS number R2(config)#ip msdp peer 3.3.3.3 connect-source lo 0                                           RACK1AS>3 [Resuming connection 3 to r3 ... ] R3#co f t    nfig t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#ip ms R3(config)#ip msdp pee R3(config)#ip msdp peer 2.2.2.2 co R3(config)#ip msdp peer 2.2.2.2 connect-source lo 0 R3(config)#do sh ip msdp peer MSDP Peer 2.2.2.2 (?), AS ? Connection status: State: Listen, Resets: 0, Connection source: Loopback0 (3.3.3.3) Uptime(Downtime): 00:00:08, Messages sent/received: 0/0 Output messages discarded: 0 Connection and counters cleared 00:00:08 ago SA Filtering: Input (S,G) filter: none, route-map: none Input RP filter: none, route-map: none Output (S,G) filter: none, route-map: none Output RP filter: none, route-map: none SA-Requests: Input filter: none Peer ttl threshold: 0 SAs learned from this peer: 0 Input queue size: 0, Output queue size: 0 R3(config)#do sh ip msdp peer MSDP Peer 2.2.2.2 (?), AS ? Connection status: State: Listen, Resets: 0, Connection source: Loopback0 (3.3.3.3) Uptime(Downtime): 00:00:21, Messages sent/received: 0/0 Output messages discarded: 0 Connection and counters cleared 00:00:21 ago SA Filtering: Input (S,G) filter: none, route-map: none Input RP filter: none, route-map: none Output (S,G) filter: none, route-map: none Output RP filter: none, route-map: none SA-Requests: Input filter: none Peer ttl threshold: 0 SAs learned from this peer: 0 Input queue size: 0, Output queue size: 0 R3(config)#do sh ip msdp peer      sh ip msdp % Incomplete command. R3(config)#do sh ip msdp^Z sh ip msdp % Incomplete command. R3#sh ip m *Mar 13 18:58:40.798: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip msdp *Mar 13 18:58:44.098: %MSDP-5-PEER_UPDOWN: Session to peer 2.2.2.2 going up R3#sh ip msdp            sh ip msdp peer MSDP Peer 2.2.2.2 (?), AS ? Connection status: State: Up, Resets: 0, Connection source: Loopback0 (3.3.3.3) Uptime(Downtime): 00:00:35, Messages sent/received: 1/1 Output messages discarded: 0 Connection and counters cleared 00:01:09 ago SA Filtering: Input (S,G) filter: none, route-map: none Input RP filter: none, route-map: none Output (S,G) filter: none, route-map: none Output RP filter: none, route-map: none SA-Requests: Input filter: none Peer ttl threshold: 0 SAs learned from this peer: 0 Input queue size: 0, Output queue size: 0 R3#sh ip mspd sa ^ % Invalid input detected at '^' marker. R3#sh ip mspd sa     dp sa R3#sh ip msdp sa-cache MSDP Source-Active Cache - 0 entries R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int lo 1 R3(config-if)#ip add 22 *Mar 13 18:59:54.862: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up R3(config-if)#ip add 223.254.254.254     254 255.255.255.255 R3(config-if)#exit R3(config)#do sh run | i rp-can ip pim rp-candidate Loopback0 group-list 1 interval 5 bidir R3(config)#no ip pim rp-candidate Loopback0 group-list 1 interval 5 bidir R3(config)#no ip pim rp-candidate Loopback0 group-list 1 interval 5 bidir group-list 1 interval 5 bidir 1 group-list 1 interval 5 bidirno ip pim rp-candidate Loopback1 group-list 1 interval 5 bidir  ip pim rp-candidate Loopback1 group-list 1 interval 5 bidir  Warning: PIMv2 not configured on Loopback1, Candidate-RP not advertised R3(config)#int lo 1 R3(config-if)#ip pim sp R3(config-if)#ip pim sparse-d R3(config-if)#ip pim sparse-dense-mode R3(config-if)#exit R3(config)# *Mar 13 19:00:52.430: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback1 R3(config)#exitip pim sparse-dense-mode nt lo 1  ip pim rp-candidate Loopback1 group-list 1 interval 5 bidir R3(config)# RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 18:58:45.142 R2(config)#int lo \  lo 1 R2(config-if)#ip add *Mar 13 19:01:07.810: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up R2(config-if)#ip add 223.254.254.254 255.255.255.255 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#exit R2(config)# *Mar 13 19:01:22.130: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 223.254.254.254 on interface Loopback1 R2(config)#ip pim rp-candidate Loopback1 group-list 1 interval 5 bidir R2(config)#^Z R2#sh ip *Mar 13 19:01:31.202: %SYS-5-CONFIG_I: Configured from console by console R2#sh ip pim rp map PIM Group-to-RP Mappings This system is a candidate RP (v2) This system is the Bootstrap Router (v2) Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2, bidir Info source: 180.40.7.3 (?), via bootstrap, priority 0, holdtime 12 Uptime: 00:00:40, expires: 00:00:08 R2# RACK1AS>6 [Resuming connection 6 to s2 ... ] %Error open S6#sh ip    run int fa 0/4 Building configuration... Current configuration : 176 bytes ! interface FastEthernet0/4 no switchport ip address 180.40.7.97 255.255.255.224 ip pim sparse-dense-mode ip igmp join-group 224.6.6.6 ip igmp join-group 224.20.68.1 end S6# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 36 ms R7# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3(config)#do sh ip msp s   dp sa MSDP Source-Active Cache - 0 entries R3(config)# RACK1AS>87  7 [Resuming connection 7 to r7 ... ] R7#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2, bidir Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 150 Uptime: 00:02:21, expires: 00:02:13 R7# R7# R7# R7# RACK1AS>2 [Resuming connection 2 to r4 ... ] R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ip pim rp-candidate Loopback1 group-list 1 interval 5 bidir      R2(config)#do sh run | i rp-can ip pim rp-candidate Loopback1 group-list 1 interval 5 R2(config)#^Z R2# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3(config)#do sh ip msdp sa ip pim rp-candidate Loopback1 group-list 1 interval 5 bidir       R3(config)#^Z R3# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7#sh ip pim rp map PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 150 Uptime: 00:03:41, expires: 00:02:24 R7#sh ip mr IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 239.148.93.1), 00:00:08/00:02:51, RP 223.254.254.254, flags: SPCL Incoming interface: FastEthernet0/1, RPF nbr 17.100.1.1 Outgoing interface list: Null (*, 224.0.1.40), 15:41:52/00:02:51, RP 0.0.0.0, flags: DCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: FastEthernet0/1, Forward/Sparse-Dense, 15:41:52/00:00:00 R7#sh ip mrpim rp mapp 224.4.4.4  Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 180.40.7.130, 64 ms R7# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar 13 19:04:32.6 R3#conf t sh ip msdp sa MSDP Source-Active Cache - 1 entries (17.100.1.2, 224.4.4.4), RP 223.254.254.254, AS ?,00:00:14/00:05:45, Peer 2.2.2.2 R3# R3# R3# RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 19:04:28 R2#sh ip msdp sa MSDP Source-Active Cache - 0 entries R2# R2# R2# R2# RACK1AS>4 [Resuming connection 4 to r2 ... ] *Mar 1 20:20:46.7 R4#p 224.6.6.6 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.6.6.6, timeout is 2 seconds: Reply to request 0 from 180.40.7.97, 24 ms R4# RACK1AS>2 [Resuming connection 2 to r4 ... ] R2#sh ip msdp sa MSDP Source-Active Cache - 1 entries (180.40.7.130, 224.6.6.6), RP 223.254.254.254, AS ?,00:00:04/00:05:55, Peer 3.3.3.3 R2#sh run | ip        b Lo interface Loopback0 ip address 2.2.2.2 255.255.255.0 ! interface Loopback1 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 226.6.6.6 Prob13 duplex auto speed auto ! interface Serial0/0/0 no ip address encapsulation frame-relay --More--   no fair-queue ! interface Serial0/0/0.1 multipoint ip address 180.40.7.35 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-multipoint frame-relay interface-dlci 203 ! interface Serial0/0/0.2 multipoint ip address 180.40.7.65 255.255.255.224 ip pim sparse-dense-mode ip ospf network point-to-point frame-relay interface-dlci 201 ! interface Serial0/0/1 ip address 180.40.7.2 255.255.255.224 ip pim sparse-dense-mode ! interface Serial0/1/0 no ip address shutdown ! interface Serial0/1/1 --More--   no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ! ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback1 group-list 1 interval 5 ip msdp peer 3.3.3.3 connect-source Loopback0 ! ip access-list extended Prob13 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! --More--   R2# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3#sh run | b Lo interface Loopback0 ip address 3.3.3.3 255.255.255.0 ip pim sparse-dense-mode ! interface Loopback1 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim sparse-dense-mode duplex auto speed auto ! interface Serial0/0/0 ip address 180.40.7.33 255.255.255.224 ip pim sparse-dense-mode --More--   encapsulation frame-relay ip ospf network point-to-multipoint no fair-queue ! interface Serial0/0/1 ip address 180.40.7.3 255.255.255.224 ip pim sparse-dense-mode clock rate 2000000 ! interface Serial0/1/0 no ip address shutdown clock rate 2000000 ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ! ! no ip http server no ip http secure-server ip pim bidir-enable --More--  ip pim spt-threshold 1 ip pim rp-candidate Loopback1 group-list 1 interval 5 ip pim register-rate-limit 2 ip msdp peer 2.2.2.2 connect-source Loopback0 ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! control-plane ! ! ! ! ! ! dial-peer cor custom ! ! ! --More--   R3#sh run Building configuration... Current configuration : 1673 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R3 ! boot-start-marker boot-end-marker ! logging buffered 4096 debugging ! no aaa new-model ! ! ip cef ! ! no ip domain lookup ip multicast-routing --More--  ! ! voice-card 0 no dspfarm ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! --More--  ! interface Loopback0 ip address 3.3.3.3 255.255.255.0 ip pim sparse-dense-mode ! interface Loopback1 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 ip address 180.40.7.129 255.255.255.224 ip pim sparse-dense-mode duplex auto speed auto ! interface Serial0/0/0 ip address 180.40.7.33 255.255.255.224 --More--   ip pim sparse-dense-mode encapsulation frame-relay ip ospf network point-to-multipoint no fair-queue ! interface Serial0/0/1 ip address 180.40.7.3 255.255.255.224 ip pim sparse-dense-mode clock rate 2000000 ! interface Serial0/1/0 no ip address shutdown clock rate 2000000 ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ! ! no ip http server no ip http secure-server --More--  ip pim bidir-enable ip pim spt-threshold 1 ip pim rp-candidate Loopback1 group-list 1 interval 5 ip pim register-rate-limit 2 ip msdp peer 2.2.2.2 connect-source Loopback0 ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! control-plane ! ! ! ! ! ! dial-peer cor custom ! ! --More--  ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login ! scheduler allocate 20000 1000 ! end R3# confi8 t ^ % Invalid input detected at '^' marker. R3#coin  nfi t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#no ip multicast-routing R3(config)#! R3(config)#interface Loopback0 R3(config-if)#no ip pim sparse-dense-mode R3(config-if)#! R3(config-if)#no interface Loopback1 R3(config)#! R3(config)#! R3(config)#interface FastEthernet0/1 R3(config-if)#no ip pim sparse-dense-mode R3(config-if)#! R3(config-if)#interface Serial0/0/0 R3(config-if)#no ip pim sparse-dense-mode R3(config-if)#! R3(config-if)#interface Serial0/0/1 R3(config-if)#no ip pim sparse-dense-mode R3(config-if)#! R3(config-if)#! R3(config-if)#! R3(config-if)#! R3(config-if)#no ip http server R3(config)#no ip http secure-server R3(config)#no ip pim bidir-enable R3(config)#no ip pim spt-threshold 1 R3(config)#no ip pim rp-candidate Loopback1 group-list 1 interval 5 ^ % Invalid input detected at '^' marker. R3(config)#no ip pim register-rate-limit 2 R3(config)#no ip msdp peer 2.2.2.2 connect-source Loopback0 R3(config)#! R3(config)# *Mar 13 19:10:56.970: %BSR-5-CRP_REMOVED: Candidate-RP on interface Loopback1 has been removed *Mar 13 19:10:57.066: %PIM-5-NBRCHG: neighbor 180.40.7.130 DOWN on interface FastEthernet0/1 DR *Mar 13 19:10:57.122: %PIM-5-NBRCHG: neighbor 180.40.7.35 DOWN on interface Serial0/0/0 DR *Mar 13 19:10:57.182: %PIM-5-NBRCHG: neighbor 180.40.7.2 DOWN on interface Serial0/0/1 non DR *Mar 13 19:10:57.474: %MSDP-5-PEER_UPDOWN: Session to peer 2.2.2.2 going down R3(config)# *Mar 13 19:10:58.966: %LINK-5-CHANGED: Interface Loopback1, changed state to administratively down *Mar 13 19:10:59.966: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to down R3(config)# R3(config)# R3(config)# R3(config)# R3(config)#^Z R3# *Mar 13 19:11:07.946: %SYS-5-CONFIG_I: Configured from console by console R3#sh ip    run | i pim R3# R3# R3# R3# R3# RACK1AS>4 [Resuming connection 4 to r2 ... ] R4#coni fig t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int lo 0 R4(config-if)#ip add 4 *Mar 1 20:37:07.844: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up R4(config-if)#ip add 4.4.4.4 255.255.255.0 R4(config-if)# *Mar 1 20:37:36.651: %PIM-5-NBRCHG: neighbor 180.40.7.129 DOWN on interface FastEthernet0/0 non DR R4(config-if)#int tu 0 R4(config-if)#tun *Mar 1 20:37:58.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R4(config-if)#tun sou lo 0 R4(config-if)#tn dest 2.,2   .2.2.2 ^ % Invalid input detected at '^' marker. R4(config-if)#tn dest 2.2.2.2un dest 2.2.2.2 R4(config-if)# *Mar 1 20:38:14.649: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R4(config-if)#ip add 24.24.24.2 \4  4 255.255.255.0 R4(config-if)#kee R4(config-if)#keepalive R4(config-if)#ip pim sp R4(config-if)#ip pim sparse-d R4(config-if)#ip pim sparse-dense-mode R4(config-if)# RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 19:10 R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int tu 0 R2(config-if)#tun sou *Mar 13 19:14:24.182: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down R2(config-if)#tun sou lo 0 R2(config-if)#tun des 4.4.4.4 R2(config-if)#ke R2(config-if)#keepalive R2(config-if)#ip a *Mar 13 19:14:35.426: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up R2(config-if)#ip add 24.24.24.2 255.255.255.0 R2(config-if)#ip pim sp R2(config-if)#ip pim sparse-d R2(config-if)#ip pim sparse-dense-mode R2(config-if)#^Z R2# *Mar 13 19:14:51.814: %SYS-5-CONFIG_I: Configured from console by console R2# R2# R2# R2# *Mar 13 19:14:53.286: %PIM-5-NBRCHG: neighbor 24.24.24.4 UP on interface Tunnel0 *Mar 13 19:14:53.338: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on Tunnel0 from LOADING to FULL, Loading Done R2# R2# R2#p 24.24.24.4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 24.24.24.4, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms R2#sh ip pim nei           p route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/65] via 180.40.7.66, 00:00:20, Serial0/0/0.2 O 17.100.1.0 [110/65] via 180.40.7.66, 00:00:20, Serial0/0/0.2 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, Loopback0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/65] via 180.40.7.33, 00:00:20, Serial0/0/0.1 [110/65] via 180.40.7.3, 00:00:20, Serial0/0/1 223.254.254.0/32 is subnetted, 1 subnets C 223.254.254.254 is directly connected, Loopback1 4.0.0.0/32 is subnetted, 1 subnets O 4.4.4.4 [110/66] via 180.40.7.33, 00:00:22, Serial0/0/0.1 [110/66] via 180.40.7.3, 00:00:22, Serial0/0/1 --More--   24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks O 180.40.7.128/27 [110/65] via 180.40.7.33, 00:00:24, Serial0/0/0.1 [110/65] via 180.40.7.3, 00:00:24, Serial0/0/1 C 180.40.7.0/27 is directly connected, Serial0/0/1 O 180.40.7.33/32 [110/64] via 180.40.7.33, 00:00:24, Serial0/0/0.1 [110/64] via 180.40.7.3, 00:00:24, Serial0/0/1 C 180.40.7.32/27 is directly connected, Serial0/0/0.1 C 180.40.7.64/27 is directly connected, Serial0/0/0.2 C 180.40.7.96/27 is directly connected, FastEthernet0/1 R2#sh ip pim int Address Interface Ver/ Nbr Query DR DR Mode Count Intvl Prior 180.40.7.98 FastEthernet0/1 v2/SD 1 30 1 180.40.7.98 180.40.7.35 Serial0/0/0.1 v2/SD 0 30 1 180.40.7.35 180.40.7.65 Serial0/0/0.2 v2/SD 1 30 1 180.40.7.66 180.40.7.2 Serial0/0/1 v2/SD 0 30 1 0.0.0.0 223.254.254.254 Loopback1 v2/SD 0 30 1 223.254.254.254 24.24.24.2 Tunnel0 v2/SD 1 30 1 0.0.0.0 R2#p 222~4.4.      4.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 4 ms R2#[29~x6       RACK1AS>6 [Resuming connection 6 to s2 ... ] S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# S6# S6# S6# RACK1AS>4 [Resuming connection 4 to r2 ... ] *Mar 1 20:39: R4(config-if)#^Z R4#sh ip rout *Mar 1 20:43:53.128: %SYS-5-CONFIG_I: Configured from console by console R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/130] via 180.40.7.129, 00:04:01, FastEthernet0/0 O 17.100.1.0 [110/130] via 180.40.7.129, 00:04:01, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/66] via 180.40.7.129, 00:04:01, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:04:01, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/66] via 180.40.7.129, 00:04:02, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More--   180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/65] via 180.40.7.129, 00:04:04, FastEthernet0/0 O 180.40.7.35/32 [110/65] via 180.40.7.129, 00:04:04, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:04:04, FastEthernet0/0 O 180.40.7.64/27 [110/129] via 180.40.7.129, 00:04:04, FastEthernet0/0 O 180.40.7.96/27 [110/66] via 180.40.7.129, 00:04:04, FastEthernet0/0 R4# *Mar 1 20:43:57.872: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 R4#conf t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int tu 0 0  R4(config-if)#do sh ip ospf int Tunnel0 is up, line protocol is up Internet Address 24.24.24.4/24, Area 0 Process ID 1, Router ID 180.40.7.130, Network Type POINT_TO_POINT, Cost: 11111 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 Hello due in 00:00:01 Supports Link-local Signaling (LLS) Index 3/3, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 180.40.7.98 Suppress hello for 0 neighbor(s) Loopback0 is up, line protocol is up Internet Address 4.4.4.4/24, Area 0 Process ID 1, Router ID 180.40.7.130, Network Type LOOPBACK, Cost: 1 Loopback interface is treated as a stub Host FastEthernet0/0 is up, line protocol is up Internet Address 180.40.7.130/27, Area 0 Process ID 1, Router ID 180.40.7.130, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 --More--   R4(config-if)#ip ospf co 1 R4(config-if)# *Mar 1 20:45:57.993: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 20:45:58.994: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 20:45:58.994: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 20:45:59.034: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 non DR R4(config-if)# *Mar 1 20:46:06.799: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 R4(config-if)# *Mar 1 20:47:09.013: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 20:47:09.021: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 R4(config-if)# *Mar 1 20:47:09.522: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 R4(config-if)# *Mar 1 20:47:18.068: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config-if)# *Mar 1 20:47:28.012: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 20:47:29.014: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 20:47:29.014: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 20:47:29.054: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 non DR R4(config-if)#ip ospf co 1nip ospf co 1oip ospf co 1 ip ospf co 1 R4(config-if)#exit R4(config)#ip mrou R4(config)#ip mroute 0.0.0.0 0.0.0.0 tu 0 R4(config)# RACK1AS>6 [Resuming connection 6 to s2 ... ] p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: . S6# RACK1AS>4 [Resuming connection 4 to r2 ... ] *Mar 1 20:48 R4(config)#do sh ip pim rp map PIM Group-to-RP Mappings R4(config)#do sh ip pim rp map PIM Group-to-RP Mappings R4(config)#do sh ip pim rp map PIM Group-to-RP Mappings R4(config)# *Mar 1 20:48:39.017: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 20:48:39.025: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 *Mar 1 20:48:39.093: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4(config)#do sh ip pim rp map PIM Group-to-RP Mappings R4(config)#do sh ip pim rp map PIM Group-to-RP Mappings R4(config)#do sh ip pim rp mapip mroute 0.0.0.0 0.0.0.0 tu 0exit no ip ospf co 1exit ip mroute 0.0.0.0 0.0.0.0 tu 0do sh ip pim rp map  do sh ip pim rp mapip mroute 0.0.0.0 0.0.0.0 tu 0do sh ip pim rp map  PIM Group-to-RP Mappings Group(s) 224.0.0.0/4 RP 223.254.254.254 (?), v2 Info source: 180.40.7.98 (?), via bootstrap, priority 0, holdtime 150 Uptime: 00:00:02, expires: 00:02:27 R4(config)#^  RACK1AS>6 [Resuming connection 6 to s2 ... ] S6#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 16 ms S6# RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 19:21 R2#sh run | b Lo interface Loopback0 ip address 2.2.2.2 255.255.255.0 ! interface Loopback1 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface Tunnel0 ip address 24.24.24.2 255.255.255.0 ip pim sparse-dense-mode keepalive 10 3 tunnel source Loopback0 tunnel destination 4.4.4.4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode --More--   R2# RACK1AS>4 [Resuming connection 4 to r2 ... ] *Mar 1 20:49:10.881: R4(config)# *Mar 1 20:50:11.035: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 R4(config)#^Z R4#sh run | b *Mar 1 20:50:12.931: %SYS-5-CONFIG_I: Configured from console by console R4#sh run | b Lo interface Loopback0 ip address 4.4.4.4 255.255.255.0 ! interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode keepalive 10 3 tunnel source Loopback0 tunnel destination 2.2.2.2 ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip pim state-refresh origination-interval 8 ip pim sparse-dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto ! interface Serial0/0 no ip address shutdown no fair-queue ! --More-- *Mar 1 20:51:11.194: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 --More-- *Mar 1 20:52:11.301: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 --More--  interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/1 no ip address shutdown ! interface Serial0/2 no ip address shutdown ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ! ! ip http server no ip http secure-server ip pim bidir-enable --More--  ip pim spt-threshold 1 ip mroute 0.0.0.0 0.0.0.0 Tunnel0 ! ! ! ! control-plane ! ! ! ! ! ! ! ! ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 --More-- *Mar 1 20:53:11.399: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 --More--   R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#do sh ip pim rp mapip mroute 0.0.0.0 0.0.0.0 tu 0nip mroute 0.0.0.0 0.0.0.0 tu 0oip mroute 0.0.0.0 0.0.0.0 tu 0 ip mroute 0.0.0.0 0.0.0.0 tu 0 R4(config)#^Z R4# *Mar 1 20:53:46.080: %SYS-5-CONFIG_I: Configured from console by console R4# *Mar 1 20:54:11.498: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 R4#confi t Enter configuration commands, one per line. End with CNTL/Z. R4(config)# *Mar 1 20:55:11.596: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 R4(config)#router ei gr   grp 100 R4(config-router)#no auto R4(config-router)#net 4.4.4.4 0.0.0.0 R4(config-router)#net 17 80.40.7.130 0.0.0.0 R4(config-router)#int tu 0 R4(config-if)#ip ospf co 1 R4(config-if)#^Z R4# RACK1AS>3 [Resuming connection 3 to r3 ... ] R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router eigrp 100 R3(config-router)#no ao ur ^ % Invalid input detected at '^' marker. R3(config-router)#no aur t R3(config-router)#net 180.40.7.129 0.0.0.0 R3(config-router)# *Mar 13 19:31:56.854: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.130 (FastEthernet0/1) is up: new adjacency R3(config-router)#net 180.40.7.3 0.0.0.0 R3(config-router)#^Z R3# RACK1AS>2 [Resuming connection 2 to r4 ... ] R2#conf t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#routeer    r is  eigrp 100 *Mar 13 19:32:15.414: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on Tunnel0 from FULL to DOWN, Neighbor Down: Dead timer expired R2(config)#router eigrp 100 R2(config-router)#no autop  R2(config-router)#net 2.2.2.2 0.0.0.0 R2(config-router)#net 180.40.7.2 0.0.0.0 R2(config-router)# *Mar 13 19:32:30.942: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.3 (Serial0/0/1) is up: new adjacency R2(config-router)# RACK1AS>4 [Resuming connection 4 to r2 ... ] *Mar 1 20:56:35.265: R4# R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/130] via 180.40.7.129, 00:00:25, FastEthernet0/0 O 17.100.1.0 [110/130] via 180.40.7.129, 00:00:25, FastEthernet0/0 2.0.0.0/8 is variably subnetted, 2 subnets, 2 masks O 2.2.2.2/32 [110/66] via 180.40.7.129, 00:00:25, FastEthernet0/0 D 2.2.2.0/24 [90/2300416] via 180.40.7.129, 00:00:15, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:00:25, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/66] via 180.40.7.129, 00:00:26, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets --More-- *Mar 1 20:57:49.118: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 20:57:49.126: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 *Mar 1 20:57:49.178: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done --More-- *Mar 1 20:57:58.117: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 20:57:59.119: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 20:57:59.119: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 20:57:59.159: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 non DR --More-- *Mar 1 20:58:05.141: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 --More-- RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 19 R2(config-router)#int lo 0 R2(config-if)#ip ospf net p R2(config-if)#ip ospf net point-to-p R2(config-if)#ip ospf net point-to-point R2(config-if)#^Z R2# *Mar 13 19:33:27.454: %SYS-5-CONFIG_I: Configured from console by console R2# RACK1AS>4 [Resuming connection 4 to r2 ... ]  O 24.24.24.0 --More--   R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/130] via 180.40.7.129, 00:00:02, FastEthernet0/0 O 17.100.1.0 [110/130] via 180.40.7.129, 00:00:02, FastEthernet0/0 2.0.0.0/24 is subnetted, 1 subnets D 2.2.2.0 [90/2300416] via 180.40.7.129, 00:01:04, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:00:02, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/66] via 180.40.7.129, 00:00:03, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets O 24.24.24.0 [110/11176] via 180.40.7.129, 00:00:03, FastEthernet0/0 --More--   180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/2172416] via 180.40.7.129, 00:01:42, FastEthernet0/0 O 180.40.7.35/32 [110/65] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.64/27 [110/129] via 180.40.7.129, 00:00:05, FastEthernet0/0 O 180.40.7.96/27 [110/66] via 180.40.7.129, 00:00:05, FastEthernet0/0 R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/130] via 180.40.7.129, 00:00:13, FastEthernet0/0 O 17.100.1.0 [110/130] via 180.40.7.129, 00:00:13, FastEthernet0/0 2.0.0.0/24 is subnetted, 1 subnets D 2.2.2.0 [90/2300416] via 180.40.7.129, 00:01:24, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:00:13, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/66] via 180.40.7.129, 00:00:14, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets O 24.24.24.0 [110/11176] via 180.40.7.129, 00:00:14, FastEthernet0/0 --More--   180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/2172416] via 180.40.7.129, 00:01:51, FastEthernet0/0 O 180.40.7.35/32 [110/65] via 180.40.7.129, 00:00:14, FastEthernet0/0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:14, FastEthernet0/0 O 180.40.7.64/27 [110/129] via 180.40.7.129, 00:00:14, FastEthernet0/0 O 180.40.7.96/27 [110/66] via 180.40.7.129, 00:00:14, FastEthernet0/0 R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES manual up up Serial0/0 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial0/1 unassigned YES unset administratively down down Serial0/2 unassigned YES unset administratively down down Loopback0 4.4.4.4 YES manual up up Tunnel0 24.24.24.4 YES manual up up R4# *Mar 1 20:59:09.121: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 20:59:09.129: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 *Mar 1 20:59:09.178: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done R4# *Mar 1 20:59:09.630: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 R4# R4# R4# R4#sh ip int brieroute  Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/66] via 24.24.24.2, 00:00:02, Tunnel0 O 17.100.1.0 [110/66] via 24.24.24.2, 00:00:02, Tunnel0 2.0.0.0/24 is subnetted, 1 subnets D 2.2.2.0 [90/2300416] via 180.40.7.129, 00:01:50, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 180.40.7.129, 00:00:02, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/2] via 24.24.24.2, 00:00:02, Tunnel0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More--   180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 D 180.40.7.0/27 [90/2172416] via 180.40.7.129, 00:02:17, FastEthernet0/0 O 180.40.7.35/32 [110/1] via 24.24.24.2, 00:00:04, Tunnel0 O 180.40.7.33/32 [110/1] via 180.40.7.129, 00:00:04, FastEthernet0/0 O 180.40.7.64/27 [110/65] via 24.24.24.2, 00:00:04, Tunnel0 O 180.40.7.96/27 [110/2] via 24.24.24.2, 00:00:04, Tunnel0 R4# R4# R4# R4# RACK1AS>7 [Resuming connection 7 to r7 ... ] R7#p 224.4.4.4 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 224.4.4.4, timeout is 2 seconds: Reply to request 0 from 24.24.24.4, 40 ms R7# R7# R7# R7# RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 19:33:36.526: R2#sh run | b eigrp router eigrp 100 network 2.2.2.2 0.0.0.0 network 180.40.7.2 0.0.0.0 no auto-summary ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ! ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback1 group-list 1 interval 5 ip msdp peer 3.3.3.3 connect-source Loopback0 ! ip access-list extended Prob13 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! --More--   R2#sh run int lo 0 Building configuration... Current configuration : 93 bytes ! interface Loopback0 ip address 2.2.2.2 255.255.255.0 ip ospf network point-to-point end R2# RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar 13 19:32:05. R3#sh run | b eigrp router eigrp 100 network 180.40.7.3 0.0.0.0 network 180.40.7.129 0.0.0.0 no auto-summary ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ! ! no ip http server no ip http secure-server ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! control-plane ! --More-- RACK1AS>4 [Resuming connection 4 to r2 ... ] R4#sbh    h run | b Tu interface Tunnel0 ip address 24.24.24.4 255.255.255.0 ip pim sparse-dense-mode ip ospf cost 1 keepalive 10 3 tunnel source Loopback0 tunnel destination 2.2.2.2 ! interface FastEthernet0/0 ip address 180.40.7.130 255.255.255.224 ip pim state-refresh origination-interval 8 ip pim sparse-dense-mode ip igmp join-group 224.4.4.4 duplex auto speed auto ! interface Serial0/0 no ip address shutdown no fair-queue ! interface FastEthernet0/1 no ip address --More--   shutdown duplex auto speed auto ! interface Serial0/1 no ip address shutdown ! interface Serial0/2 no ip address shutdown ! router eigrp 100 network 4.4.4.4 0.0.0.0 network 180.40.7.130 0.0.0.0 no auto-summary ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! ! ! --More--   R4#onf t ^ % Invalid input detected at '^' marker. R4#conf t Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int tu 0 R4(config-if)#no ip ospf co R4(config-if)#exit R4(config)#no router ieg     eigrp *Mar 1 21:02:36.638: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 188 R4(config)#no router eigrp 100 *Mar 1 21:02:39.038: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.129 (FastEthernet0/0) is down: interface down RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar 13 19:37 ! --More--   R3#conf t Enter configuration commands, one per line. End with CNTL/Z. R3(config)#router      no router eigrp 100 RACK1AS>2 [Resuming connection 2 to r4 ... ] *Mar 13 19:37:53.514: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 180.40.7.3 (Serial0/0/1) is down: Interface Goodbye received R2# R2#confi t Enter configuration commands, one per line. End with CNTL/Z. R2(config)#nbo router           o router eigrp 100 R2(config)#router ospf 1 R2(config-router)#net 2.2.2.2 0.0.0.0 area 51 R2(config-router)#net *Mar 13 19:40:00.694: %OSPF-6-AREACHG: 2.2.2.2/32 changed from area 0 to area 51 R2(config-router)#net 180.40.7.2 0.0.0.0 area 00    51 R2(config-router)# *Mar 13 19:40:10.546: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on Serial0/0/1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 13 19:40:10.546: %OSPF-6-AREACHG: 180.40.7.2/32 changed from area 0 to area 51 R2(config-router)#^Z R2# *Mar 13 19:40:11.050: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virt RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar 13 19:37:52.490: R3(config)#router ospf 1 R3(config-router)#net 180.; 40./ 7.3 0.0.0.0 area 51 R3(config-router)#net 180.40.7.3 0.0.0.0 area 51 *Mar 13 19:40:26.066: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial0/0/1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 13 19:40:26.070: %OSPF-6-AREACHG: 180.40.7.3/32 changed from area 0 to area 51 R3(config-router)#net 180.40.7.3 0.0.0.0 area 51 *Mar 13 19:40:26.086: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Serial0/0/1 from LOADING to FULL, Loading Done R3(config-router)#net 180.40.7.3 0.0.0.0 area 51 0.0.0.0 area 51 1 0.0.0.0 area 512 0.0.0.0 area 519 0.0.0.0 area 51 R3(config-router)#^Z R3# *Mar 13 19:40:31.118: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.130 on FastEthernet0/1 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 13 19:40:31.122: %OSPF-6-AREACHG: 180.40.7.129/32 changed from area 0 to area 51 *Mar 13 19:40:31.654: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 180.40.7.130, FastEthernet0/1 R3# RACK1AS>4 [Resuming connection 4 to r2 ... ] R4(config)# R4(config)#router ospf 1 R4(config-router)#area  \     net 4.4.4.4.  0.0.0.0 area 51 R4(config-router)#n *Mar 1 21:05:42.446: %OSPF-6-AREACHG: 4.4.4.4/32 changed from area 0 to area 51 R4(config-router)#net 180.40.7.130 0.0.0.0 *Mar 1 21:05:48.256: %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing *Mar 1 21:05:49.257: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to down *Mar 1 21:05:49.257: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from FULL to DOWN, Neighbor Down: Interface down or detached *Mar 1 21:05:49.297: %PIM-5-NBRCHG: neighbor 24.24.24.2 DOWN on interface Tunnel0 non DR R4(config-router)#net 180.40.7.130 0.0.0.0 area 51 R4(config-router)# *Mar 1 21:05:50.996: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from FULL to DOWN, Neighbor Down: Interface down or detached R4(config-router)#^Z R4# *Mar 1 21:05:51.000: %OSPF-6-AREACHG: 180.40.7.130/32 changed from area 0 to area 51 R4# *Mar 1 21:05:51.609: %SYS-5-CONFIG_I: Configured from console by console R4# R4# R4# R4# R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.129 1 2WAY/DROTHER 00:00:36 180.40.7.129 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.129 1 2WAY/DROTHER 00:00:37 180.40.7.129 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.129 1 FULL/BDR 00:00:39 180.40.7.129 FastEthernet0/0 R4# *Mar 1 21:06:31.014: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.129 on FastEthernet0/0 from LOADING to FULL, Loading Done R4# R4# R4# R4# R4# R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.129 1 FULL/BDR 00:00:36 180.40.7.129 FastEthernet0/0 R4#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 180.40.7.129 1 FULL/BDR 00:00:34 180.40.7.129 FastEthernet0/0 R4#sh ip int brie Interface IP-Address OK? Method Status Protocol FastEthernet0/0 180.40.7.130 YES manual up up Serial0/0 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial0/1 unassigned YES unset administratively down down Serial0/2 unassigned YES unset administratively down down Loopback0 4.4.4.4 YES manual up up Tunnel0 24.24.24.4 YES manual up down R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O IA 17.57.100.0 [110/130] via 180.40.7.129, 00:00:16, FastEthernet0/0 O IA 17.100.1.0 [110/130] via 180.40.7.129, 00:00:16, FastEthernet0/0 2.0.0.0/24 is subnetted, 1 subnets O 2.2.2.0 [110/66] via 180.40.7.129, 00:00:16, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O IA 3.3.3.3 [110/2] via 180.40.7.129, 00:00:16, FastEthernet0/0 223.254.254.0/32 is subnetted, 1 subnets O IA 223.254.254.254 [110/66] via 180.40.7.129, 00:00:17, FastEthernet0/0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 --More-- *Mar 1 21:06:59.260: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel0, changed state to up *Mar 1 21:06:59.268: %PIM-5-NBRCHG: neighbor 24.24.24.2 UP on interface Tunnel0 *Mar 1 21:06:59.340: %OSPF-5-ADJCHG: Process 1, Nbr 180.40.7.98 on Tunnel0 from LOADING to FULL, Loading Done --More--  O 180.40.7.0/27 [110/65] via 180.40.7.129, 00:00:02, FastEthernet0/0 R4# R4# R4#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 17.0.0.0/24 is subnetted, 2 subnets O 17.57.100.0 [110/11176] via 24.24.24.2, 00:00:00, Tunnel0 O 17.100.1.0 [110/11176] via 24.24.24.2, 00:00:00, Tunnel0 2.0.0.0/24 is subnetted, 1 subnets O 2.2.2.0 [110/66] via 180.40.7.129, 00:00:00, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/11176] via 24.24.24.2, 00:00:00, Tunnel0 223.254.254.0/32 is subnetted, 1 subnets O 223.254.254.254 [110/11112] via 24.24.24.2, 00:00:00, Tunnel0 4.0.0.0/24 is subnetted, 1 subnets C 4.4.4.0 is directly connected, Loopback0 24.0.0.0/24 is subnetted, 1 subnets C 24.24.24.0 is directly connected, Tunnel0 --More--   180.40.0.0/16 is variably subnetted, 6 subnets, 2 masks C 180.40.7.128/27 is directly connected, FastEthernet0/0 O 180.40.7.0/27 [110/65] via 180.40.7.129, 00:00:01, FastEthernet0/0 O 180.40.7.35/32 [110/11111] via 24.24.24.2, 00:00:01, Tunnel0 O 180.40.7.33/32 [110/11175] via 24.24.24.2, 00:00:01, Tunnel0 O 180.40.7.64/27 [110/11175] via 24.24.24.2, 00:00:01, Tunnel0 O 180.40.7.96/27 [110/11112] via 24.24.24.2, 00:00:01, Tunnel0 R4# RACK1AS>2 [Resuming connection 2 to r4 ... ] ual-link but not found R2#sh run | b ospf ip ospf network point-to-point ! interface Loopback1 ip address 223.254.254.254 255.255.255.255 ip pim sparse-dense-mode ! interface Tunnel0 ip address 24.24.24.2 255.255.255.0 ip pim sparse-dense-mode keepalive 10 3 tunnel source Loopback0 tunnel destination 4.4.4.4 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 ip address 180.40.7.98 255.255.255.224 ip pim sparse-dense-mode ip multicast helper-map broadcast 226.6.6.6 Prob13 --More--   R2#sh run | b router router ospf 1 log-adjacency-changes network 2.2.2.2 0.0.0.0 area 51 network 180.40.7.2 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ! ! no ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ip pim bsr-candidate FastEthernet0/1 0 ip pim rp-candidate Loopback1 group-list 1 interval 5 ip msdp peer 3.3.3.3 connect-source Loopback0 ! ip access-list extended Prob13 permit udp host 180.40.7.97 host 255.255.255.255 eq tftp ! ! ! ! ! --More-- RACK1AS>3 [Resuming connection 3 to r3 ... ] *Mar 13 19:40:31. R3#sh run | b router router ospf 1 log-adjacency-changes network 180.40.7.3 0.0.0.0 area 51 network 180.40.7.129 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ! ! no ip http server no ip http secure-server ! access-list 1 deny 224.20.68.1 access-list 1 permit any access-list 100 permit ip any any ! ! ! ! control-plane ! ! ! ! --More-- RACK1AS>4 [Resuming connection 4 to r2 ... ] R4#sh run | b router router ospf 1 log-adjacency-changes network 4.4.4.4 0.0.0.0 area 51 network 180.40.7.130 0.0.0.0 area 51 network 0.0.0.0 255.255.255.255 area 0 ! ! ! ip http server no ip http secure-server ip pim bidir-enable ip pim spt-threshold 1 ! ! ! ! control-plane ! ! ! ! ! ! --More--